| Age | Commit message (Collapse) | Author |
|---|
|
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f040 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f040 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.
Fixes: 5950c7c0a68c ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.
In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.
To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.
Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.
[This is a duplicate of commit 2c0ab32b73cf ("hinic: Replace memcpy()
with direct assignment") which was applied to net-next.]
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
vxge-main.c"
This reverts commit 8fc74d18639a2402ca52b177e990428e26ea881f.
BAR0 is the main (only?) register bank for this device. We most
obviously can't unmap it before the netdev is unregistered.
This was pointed out in review but the patch got reposted and
merged, anyway.
The author of the patch was only testing it with a QEMU model,
which I presume does not emulate enough for the netdev to be brought
up (author's replies are not visible in lore because they kept sending
their emails in HTML).
Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/
Fixes: 8fc74d18639a ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon reports that if two LAN9514 USB adapters are directly connected
without an intermediate switch, the link fails to come up and link LEDs
remain dark. The issue was introduced by commit 1ce8b37241ed ("usbnet:
smsc95xx: Forward PHY interrupts to PHY driver to avoid polling").
The PHY suffers from a known erratum wherein link detection becomes
unreliable if Energy Detect Power-Down is used. In poll mode, the
driver works around the erratum by briefly disabling EDPD for 640 msec
to detect a neighbor, then re-enabling it to save power.
In interrupt mode, no interrupt is signaled if EDPD is used by both link
partners, so it must not be enabled at all.
We'll recoup the power savings by enabling SUSPEND1 mode on affected
LAN95xx chips in a forthcoming commit.
Fixes: 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Latest kernel will explode on the PHY interrupt config, since it depends
now on allocated priv. So, run probe to allocate priv to fix it.
ar9331_switch ethernet.1:10 lan0 (uninitialized): PHY [!ahb!ethernet@1a000000!mdio!switch@10:00] driver [Qualcomm Atheros AR9331 built-in PHY] (irq=13)
CPU 0 Unable to handle kernel paging request at virtual address 0000000a, epc == 8050e8a8, ra == 80504b34
...
Call Trace:
[<8050e8a8>] at803x_config_intr+0x5c/0xd0
[<80504b34>] phy_request_interrupt+0xa8/0xd0
[<8050289c>] phylink_bringup_phy+0x2d8/0x3ac
[<80502b68>] phylink_fwnode_phy_connect+0x118/0x130
[<8074d8ec>] dsa_slave_create+0x270/0x420
[<80743b04>] dsa_port_setup+0x12c/0x148
[<8074580c>] dsa_register_switch+0xaf0/0xcc0
[<80511344>] ar9331_sw_probe+0x370/0x388
[<8050cb78>] mdio_probe+0x44/0x70
[<804df300>] really_probe+0x200/0x424
[<804df7b4>] __driver_probe_device+0x290/0x298
[<804df810>] driver_probe_device+0x54/0xe4
[<804dfd50>] __device_attach_driver+0xe4/0x130
[<804dcb00>] bus_for_each_drv+0xb4/0xd8
[<804dfac4>] __device_attach+0x104/0x1a4
[<804ddd24>] bus_probe_device+0x48/0xc4
[<804deb44>] deferred_probe_work_func+0xf0/0x10c
[<800a0ffc>] process_one_work+0x314/0x4d4
[<800a17fc>] worker_thread+0x2a4/0x354
[<800a9a54>] kthread+0x134/0x13c
[<8006306c>] ret_from_kernel_thread+0x14/0x1c
Same Issue would affect some other PHYs (QCA8081, QCA9561), so fix it
too.
Fixes: 3265f4218878 ("net: phy: at803x: add fiber support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointer vdev points to a memory region adjacent to a net_device
structure ndev, which is a field of hldev. At line 4740, the invocation
to vxge_device_unregister unregisters device hldev, and it also releases
the memory region pointed by vdev->bar0. At line 4743, the freed memory
region is referenced (i.e., iounmap(vdev->bar0)), resulting in a
use-after-free vulnerability. We can fix the bug by calling iounmap
before vxge_device_unregister.
4721. static void vxge_remove(struct pci_dev *pdev)
4722. {
4723. struct __vxge_hw_device *hldev;
4724. struct vxgedev *vdev;
…
4731. vdev = netdev_priv(hldev->ndev);
…
4740. vxge_device_unregister(hldev);
4741. /* Do not call pci_disable_sriov here, as it
will break child devices */
4742. vxge_hw_device_terminate(hldev);
4743. iounmap(vdev->bar0);
…
4749 vxge_debug_init(vdev->level_trace, "%s:%d
Device unregistered",
4750 __func__, __LINE__);
4751 vxge_debug_entryexit(vdev->level_trace, "%s:%d
Exiting...", __func__,
4752 __LINE__);
4753. }
This is the screenshot when the vulnerability is triggered by using
KASAN. We can see that there is a use-after-free reported by KASAN.
/***************************start**************************/
root@kernel:~# echo 1 > /sys/bus/pci/devices/0000:00:03.0/remove
[ 178.296316] vxge_remove
[ 182.057081]
==================================================================
[ 182.057548] BUG: KASAN: use-after-free in vxge_remove+0xe0/0x15c
[ 182.057760] Read of size 8 at addr ffff888006c76598 by task bash/119
[ 182.057983]
[ 182.058747] CPU: 0 PID: 119 Comm: bash Not tainted 5.18.0 #5
[ 182.058919] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 182.059463] Call Trace:
[ 182.059726] <TASK>
[ 182.060017] dump_stack_lvl+0x34/0x44
[ 182.060316] print_report.cold+0xb2/0x6b7
[ 182.060401] ? kfree+0x89/0x290
[ 182.060478] ? vxge_remove+0xe0/0x15c
[ 182.060545] kasan_report+0xa9/0x120
[ 182.060629] ? vxge_remove+0xe0/0x15c
[ 182.060706] vxge_remove+0xe0/0x15c
[ 182.060793] pci_device_remove+0x5d/0xe0
[ 182.060968] device_release_driver_internal+0xf1/0x180
[ 182.061063] pci_stop_bus_device+0xae/0xe0
[ 182.061150] pci_stop_and_remove_bus_device_locked+0x11/0x20
[ 182.061236] remove_store+0xc6/0xe0
[ 182.061297] ? subordinate_bus_number_show+0xc0/0xc0
[ 182.061359] ? __mutex_lock_slowpath+0x10/0x10
[ 182.061438] ? sysfs_kf_write+0x6d/0xa0
[ 182.061525] kernfs_fop_write_iter+0x1b0/0x260
[ 182.061610] ? sysfs_kf_bin_read+0xf0/0xf0
[ 182.061695] new_sync_write+0x209/0x310
[ 182.061789] ? new_sync_read+0x310/0x310
[ 182.061865] ? cgroup_rstat_updated+0x5c/0x170
[ 182.061937] ? preempt_count_sub+0xf/0xb0
[ 182.061995] ? pick_next_entity+0x13a/0x220
[ 182.062063] ? __inode_security_revalidate+0x44/0x80
[ 182.062155] ? security_file_permission+0x46/0x2a0
[ 182.062230] vfs_write+0x33f/0x3e0
[ 182.062303] ksys_write+0xb4/0x150
[ 182.062369] ? __ia32_sys_read+0x40/0x40
[ 182.062451] do_syscall_64+0x3b/0x90
[ 182.062531] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 182.062894] RIP: 0033:0x7f3f37d17274
[ 182.063558] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f
80 00 00 00 00 48 8d 05 89 54 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53
[ 182.063797] RSP: 002b:00007ffd5ba9e178 EFLAGS: 00000246
ORIG_RAX: 0000000000000001
[ 182.064117] RAX: ffffffffffffffda RBX: 0000000000000002
RCX: 00007f3f37d17274
[ 182.064219] RDX: 0000000000000002 RSI: 000055bbec327180
RDI: 0000000000000001
[ 182.064315] RBP: 000055bbec327180 R08: 000000000000000a
R09: 00007f3f37de7cf0
[ 182.064414] R10: 000000000000000a R11: 0000000000000246
R12: 00007f3f37de8760
[ 182.064513] R13: 0000000000000002 R14: 00007f3f37de3760
R15: 0000000000000002
[ 182.064691] </TASK>
[ 182.064916]
[ 182.065224] The buggy address belongs to the physical page:
[ 182.065804] page:00000000ef31e4f4 refcount:0 mapcount:0
mapping:0000000000000000 index:0x0 pfn:0x6c76
[ 182.067419] flags: 0x100000000000000(node=0|zone=1)
[ 182.068997] raw: 0100000000000000 0000000000000000
ffffea00001b1d88 0000000000000000
[ 182.069118] raw: 0000000000000000 0000000000000000
00000000ffffffff 0000000000000000
[ 182.069294] page dumped because: kasan: bad access detected
[ 182.069331]
[ 182.069360] Memory state around the buggy address:
[ 182.070006] ffff888006c76480: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 182.070136] ffff888006c76500: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 182.070230] >ffff888006c76580: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 182.070305] ^
[ 182.070456] ffff888006c76600: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 182.070505] ffff888006c76680: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 182.070606]
==================================================================
[ 182.071374] Disabling lock debugging due to kernel taint
/*****************************end*****************************/
After fixing the bug as done in the patch, we can find KASAN do not report
the bug and the device(00:03.0) has been successfully removed.
/*****************************start***************************/
root@kernel:~# echo 1 > /sys/bus/pci/devices/0000:00:03.0/remove
root@kernel:~#
/******************************end****************************/
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bonding ARP monitor fails to decrement send_peer_notif, the
number of peer notifications (gratuitous ARP or ND) to be sent. This
results in a continuous series of notifications.
Correct this by decrementing the counter for each notification.
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: b0929915e035 ("bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for ab arp monitor")
Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/9400.1655407960@famine
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following use-after-free bug in igb_clean_tx_ring routine when
the NIC is running in XDP mode. The issue can be triggered redirecting
traffic into the igb NIC and then closing the device while the traffic
is flowing.
[ 73.322719] CPU: 1 PID: 487 Comm: xdp_redirect Not tainted 5.18.3-apu2 #9
[ 73.330639] Hardware name: PC Engines APU2/APU2, BIOS 4.0.7 02/28/2017
[ 73.337434] RIP: 0010:refcount_warn_saturate+0xa7/0xf0
[ 73.362283] RSP: 0018:ffffc9000081f798 EFLAGS: 00010282
[ 73.367761] RAX: 0000000000000000 RBX: ffffc90000420f80 RCX: 0000000000000000
[ 73.375200] RDX: ffff88811ad22d00 RSI: ffff88811ad171e0 RDI: ffff88811ad171e0
[ 73.382590] RBP: 0000000000000900 R08: ffffffff82298f28 R09: 0000000000000058
[ 73.390008] R10: 0000000000000219 R11: ffffffff82280f40 R12: 0000000000000090
[ 73.397356] R13: ffff888102343a40 R14: ffff88810359e0e4 R15: 0000000000000000
[ 73.404806] FS: 00007ff38d31d740(0000) GS:ffff88811ad00000(0000) knlGS:0000000000000000
[ 73.413129] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 73.419096] CR2: 000055cff35f13f8 CR3: 0000000106391000 CR4: 00000000000406e0
[ 73.426565] Call Trace:
[ 73.429087] <TASK>
[ 73.431314] igb_clean_tx_ring+0x43/0x140 [igb]
[ 73.436002] igb_down+0x1d7/0x220 [igb]
[ 73.439974] __igb_close+0x3c/0x120 [igb]
[ 73.444118] igb_xdp+0x10c/0x150 [igb]
[ 73.447983] ? igb_pci_sriov_configure+0x70/0x70 [igb]
[ 73.453362] dev_xdp_install+0xda/0x110
[ 73.457371] dev_xdp_attach+0x1da/0x550
[ 73.461369] do_setlink+0xfd0/0x10f0
[ 73.465166] ? __nla_validate_parse+0x89/0xc70
[ 73.469714] rtnl_setlink+0x11a/0x1e0
[ 73.473547] rtnetlink_rcv_msg+0x145/0x3d0
[ 73.477709] ? rtnl_calcit.isra.0+0x130/0x130
[ 73.482258] netlink_rcv_skb+0x8d/0x110
[ 73.486229] netlink_unicast+0x230/0x340
[ 73.490317] netlink_sendmsg+0x215/0x470
[ 73.494395] __sys_sendto+0x179/0x190
[ 73.498268] ? move_addr_to_user+0x37/0x70
[ 73.502547] ? __sys_getsockname+0x84/0xe0
[ 73.506853] ? netlink_setsockopt+0x1c1/0x4a0
[ 73.511349] ? __sys_setsockopt+0xc8/0x1d0
[ 73.515636] __x64_sys_sendto+0x20/0x30
[ 73.519603] do_syscall_64+0x3b/0x80
[ 73.523399] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 73.528712] RIP: 0033:0x7ff38d41f20c
[ 73.551866] RSP: 002b:00007fff3b945a68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[ 73.559640] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ff38d41f20c
[ 73.567066] RDX: 0000000000000034 RSI: 00007fff3b945b30 RDI: 0000000000000003
[ 73.574457] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
[ 73.581852] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff3b945ab0
[ 73.589179] R13: 0000000000000000 R14: 0000000000000003 R15: 00007fff3b945b30
[ 73.596545] </TASK>
[ 73.598842] ---[ end trace 0000000000000000 ]---
Fixes: 9cbc948b5a20c ("igb: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/e5c01d549dc37bff18e46aeabd6fb28a7bcf84be.1655388571.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hulk Robot reports incorrect sp->rx_count_cooked value in decode_std_command().
This should be caused by the subtracting from sp->rx_count_cooked before.
It seems that sp->rx_count_cooked value is changed to 0, which bypassed the
previous judgment.
The situation is shown below:
(Thread 1) | (Thread 2)
decode_std_command() | resync_tnc()
... |
if (rest == 2) |
sp->rx_count_cooked -= 2; |
else if (rest == 3) | ...
| sp->rx_count_cooked = 0;
sp->rx_count_cooked -= 1; |
for (i = 0; i < sp->rx_count_cooked; i++) // report error
checksum += sp->cooked_buf[i];
sp->rx_count_cooked is a shared variable but is not protected by a lock.
The same applies to sp->rx_count. This patch adds a lock to fix the bug.
The fail log is shown below:
=======================================================================
UBSAN: array-index-out-of-bounds in drivers/net/hamradio/6pack.c:925:31
index 400 is out of range for type 'unsigned char [400]'
CPU: 3 PID: 7433 Comm: kworker/u10:1 Not tainted 5.18.0-rc5-00163-g4b97bac0756a #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
Workqueue: events_unbound flush_to_ldisc
Call Trace:
<TASK>
dump_stack_lvl+0xcd/0x134
ubsan_epilogue+0xb/0x50
__ubsan_handle_out_of_bounds.cold+0x62/0x6c
sixpack_receive_buf+0xfda/0x1330
tty_ldisc_receive_buf+0x13e/0x180
tty_port_default_receive_buf+0x6d/0xa0
flush_to_ldisc+0x213/0x3f0
process_one_work+0x98f/0x1620
worker_thread+0x665/0x1080
kthread+0x2e9/0x3a0
ret_from_fork+0x1f/0x30
...
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xu Jia <xujia39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 21a75f0915dd ("bonding: Fix ARP monitor validation"),
the bonding ARP / ND link monitors depend on the trans_start time to
determine link availability. NETIF_F_LLTX drivers must update trans_start
directly, which veth does not do. This prevents use of the ARP or ND link
monitors with veth interfaces in a bond.
Resolve this by having veth_xmit update the trans_start time.
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 21a75f0915dd ("bonding: Fix ARP monitor validation")
Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even when the eth port is resticted to work with speeds not higher than 1G,
and so the eth driver is requesting the phy (via phylink) to advertise up
to 1000BASET support, the aquantia phy device is still advertising for 2.5G
and 5G speeds.
Clear these advertising defaults when requested.
Cc: Ondrej Spacek <ondrej.spacek@nxp.com>
Fixes: 09c4c57f7bc41 ("net: phy: aquantia: add support for auto-negotiation configuration")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220610084037.7625-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Mostly driver fixes.
Current release - regressions:
- Revert "net: Add a second bind table hashed by port and address",
needs more work
- amd-xgbe: use platform_irq_count(), static setup of IRQ resources
had been removed from DT core
- dts: at91: ksz9477_evb: add phy-mode to fix port/phy validation
Current release - new code bugs:
- hns3: modify the ring param print info
Previous releases - always broken:
- axienet: make the 64b addressable DMA depends on 64b architectures
- iavf: fix issue with MAC address of VF shown as zero
- ice: fix PTP TX timestamp offset calculation
- usb: ax88179_178a needs FLAG_SEND_ZLP
Misc:
- document some net.sctp.* sysctls"
* tag 'net-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (31 commits)
net: axienet: add missing error return code in axienet_probe()
Revert "net: Add a second bind table hashed by port and address"
net: ax25: Fix deadlock caused by skb_recv_datagram in ax25_recvmsg
net: usb: ax88179_178a needs FLAG_SEND_ZLP
MAINTAINERS: add include/dt-bindings/net to NETWORKING DRIVERS
ARM: dts: at91: ksz9477_evb: fix port/phy validation
net: bgmac: Fix an erroneous kfree() in bgmac_remove()
ice: Fix memory corruption in VF driver
ice: Fix queue config fail handling
ice: Sync VLAN filtering features for DVM
ice: Fix PTP TX timestamp offset calculation
mlxsw: spectrum_cnt: Reorder counter pools
docs: networking: phy: Fix a typo
amd-xgbe: Use platform_irq_count()
octeontx2-vf: Add support for adaptive interrupt coalescing
xilinx: Fix build on x86.
net: axienet: Use iowrite64 to write all 64b descriptor pointers
net: axienet: make the 64b addresable DMA depends on 64b archectures
net: hns3: fix tm port shapping of fibre port is incorrect after driver initialization
net: hns3: fix PF rss size initialization bug
...
|
|
It should return error code in error path in axienet_probe().
Fixes: 00be43a74ca2 ("net: axienet: make the 64b addresable DMA depends on 64b archectures")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220616062917.3601-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The extra byte inserted by usbnet.c when
(length % dev->maxpacket == 0) is causing problems to device.
This patch sets FLAG_SEND_ZLP to avoid this.
Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
"message authentication code incorrect"
This happens because the tcp message sent is corrupted during the
USB "Bulk out". The device calculate the tcp checksum and send a
valid tcp message to the remote sshd. Then the encryption detects
the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
The "Bulk in" continue receiving packets normally.
The host sends "Bulk out" and the device responds with -ECONNRESET.
(The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.
A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination} # 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-14
This series contains updates to ice driver only.
Michal fixes incorrect Tx timestamp offset calculation for E822 devices.
Roman enforces required VLAN filtering settings for double VLAN mode.
Przemyslaw fixes memory corruption issues with VFs by ensuring
queues are disabled in the error path of VF queue configuration and to
disabled VFs during reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'bgmac' is part of a managed resource allocated with bgmac_alloc(). It
should not be freed explicitly.
Remove the erroneous kfree() from the .remove() function.
Fixes: 34a5102c3235 ("net: bgmac: allocate struct bgmac just once & don't copy it")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/a026153108dd21239036a032b95c25b5cece253b.1655153616.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Disable VF's RX/TX queues, when it's disabled. VF can have queues enabled,
when it requests a reset. If PF driver assumes that VF is disabled,
while VF still has queues configured, VF may unmap DMA resources.
In such scenario device still can map packets to memory, which ends up
silently corrupting it.
Previously, VF driver could experience memory corruption, which lead to
crash:
[ 5119.170157] BUG: unable to handle kernel paging request at 00001b9780003237
[ 5119.170166] PGD 0 P4D 0
[ 5119.170173] Oops: 0002 [#1] PREEMPT_RT SMP PTI
[ 5119.170181] CPU: 30 PID: 427592 Comm: kworker/u96:2 Kdump: loaded Tainted: G W I --------- - - 4.18.0-372.9.1.rt7.166.el8.x86_64 #1
[ 5119.170189] Hardware name: Dell Inc. PowerEdge R740/014X06, BIOS 2.3.10 08/15/2019
[ 5119.170193] Workqueue: iavf iavf_adminq_task [iavf]
[ 5119.170219] RIP: 0010:__page_frag_cache_drain+0x5/0x30
[ 5119.170238] Code: 0f 0f b6 77 51 85 f6 74 07 31 d2 e9 05 df ff ff e9 90 fe ff ff 48 8b 05 49 db 33 01 eb b4 0f 1f 80 00 00 00 00 0f 1f 44 00 00 <f0> 29 77 34 74 01 c3 48 8b 07 f6 c4 80 74 0f 0f b6 77 51 85 f6 74
[ 5119.170244] RSP: 0018:ffffa43b0bdcfd78 EFLAGS: 00010282
[ 5119.170250] RAX: ffffffff896b3e40 RBX: ffff8fb282524000 RCX: 0000000000000002
[ 5119.170254] RDX: 0000000049000000 RSI: 0000000000000000 RDI: 00001b9780003203
[ 5119.170259] RBP: ffff8fb248217b00 R08: 0000000000000022 R09: 0000000000000009
[ 5119.170262] R10: 2b849d6300000000 R11: 0000000000000020 R12: 0000000000000000
[ 5119.170265] R13: 0000000000001000 R14: 0000000000000009 R15: 0000000000000000
[ 5119.170269] FS: 0000000000000000(0000) GS:ffff8fb1201c0000(0000) knlGS:0000000000000000
[ 5119.170274] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5119.170279] CR2: 00001b9780003237 CR3: 00000008f3e1a003 CR4: 00000000007726e0
[ 5119.170283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 5119.170286] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 5119.170290] PKRU: 55555554
[ 5119.170292] Call Trace:
[ 5119.170298] iavf_clean_rx_ring+0xad/0x110 [iavf]
[ 5119.170324] iavf_free_rx_resources+0xe/0x50 [iavf]
[ 5119.170342] iavf_free_all_rx_resources.part.51+0x30/0x40 [iavf]
[ 5119.170358] iavf_virtchnl_completion+0xd8a/0x15b0 [iavf]
[ 5119.170377] ? iavf_clean_arq_element+0x210/0x280 [iavf]
[ 5119.170397] iavf_adminq_task+0x126/0x2e0 [iavf]
[ 5119.170416] process_one_work+0x18f/0x420
[ 5119.170429] worker_thread+0x30/0x370
[ 5119.170437] ? process_one_work+0x420/0x420
[ 5119.170445] kthread+0x151/0x170
[ 5119.170452] ? set_kthread_struct+0x40/0x40
[ 5119.170460] ret_from_fork+0x35/0x40
[ 5119.170477] Modules linked in: iavf sctp ip6_udp_tunnel udp_tunnel mlx4_en mlx4_core nfp tls vhost_net vhost vhost_iotlb tap tun xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink bridge stp llc rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache sunrpc intel_rapl_msr iTCO_wdt iTCO_vendor_support dell_smbios wmi_bmof dell_wmi_descriptor dcdbas kvm_intel kvm irqbypass intel_rapl_common isst_if_common skx_edac irdma nfit libnvdimm x86_pkg_temp_thermal i40e intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ib_uverbs rapl ipmi_ssif intel_cstate intel_uncore mei_me pcspkr acpi_ipmi ib_core mei lpc_ich i2c_i801 ipmi_si ipmi_devintf wmi ipmi_msghandler acpi_power_meter xfs libcrc32c sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ice ahci drm libahci crc32c_intel libata tg3 megaraid_sas
[ 5119.170613] i2c_algo_bit dm_mirror dm_region_hash dm_log dm_mod fuse [last unloaded: iavf]
[ 5119.170627] CR2: 00001b9780003237
Fixes: ec4f5a436bdf ("ice: Check if VF is disabled for Opcode and other operations")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Co-developed-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Disable VF's RX/TX queues, when VIRTCHNL_OP_CONFIG_VSI_QUEUES fail.
Not disabling them might lead to scenario, where PF driver leaves VF
queues enabled, when VF's VSI failed queue config.
In this scenario VF should not have RX/TX queues enabled. If PF failed
to set up VF's queues, VF will reset due to TX timeouts in VF driver.
Initialize iterator 'i' to -1, so if error happens prior to configuring
queues then error path code will not disable queue 0. Loop that
configures queues will is using same iterator, so error path code will
only disable queues that were configured.
Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Suggested-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
VLAN filtering features, that is C-Tag and S-Tag, in DVM mode must be
both enabled or disabled.
In case of turning off/on only one of the features, another feature must
be turned off/on automatically with issuing an appropriate message to
the kernel log.
Fixes: 1babaf77f49d ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev")
Signed-off-by: Roman Storozhenko <roman.storozhenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The offset was being incorrectly calculated for E822 - that led to
collisions in choosing TX timestamp register location when more than
one port was trying to use timestamping mechanism.
In E822 one quad is being logically split between ports, so quad 0 is
having trackers for ports 0-3, quad 1 ports 4-7 etc. Each port should
have separate memory location for tracking timestamps. Due to error for
example ports 1 and 2 had been assigned to quad 0 with same offset (0),
while port 1 should have offset 0 and 1 offset 16.
Fix it by correctly calculating quad offset.
Fixes: 3a7496234d17 ("ice: implement basic E822 PTP support")
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 MMIO stale data fixes from Thomas Gleixner:
"Yet another hw vulnerability with a software mitigation: Processor
MMIO Stale Data.
They are a class of MMIO-related weaknesses which can expose stale
data by propagating it into core fill buffers. Data which can then be
leaked using the usual speculative execution methods.
Mitigations include this set along with microcode updates and are
similar to MDS and TAA vulnerabilities: VERW now clears those buffers
too"
* tag 'x86-bugs-2022-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/mmio: Print SMT warning
KVM: x86/speculation: Disable Fill buffer clear within guests
x86/speculation/mmio: Reuse SRBDS mitigation for SBDS
x86/speculation/srbds: Update SRBDS mitigation selection
x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data
x86/speculation/mmio: Enable CPU Fill buffer clearing on idle
x86/bugs: Group MDS, TAA & Processor MMIO Stale Data mitigations
x86/speculation/mmio: Add mitigation for Processor MMIO Stale Data
x86/speculation: Add a common function for MD_CLEAR mitigation update
x86/speculation/mmio: Enumerate Processor MMIO Stale Data bug
Documentation: Add documentation for Processor MMIO Stale Data
|
|
Both RIF and ACL flow counters use a 24-bit SW-managed counter address to
communicate which counter they want to bind.
In a number of Spectrum FW releases, binding a RIF counter is broken and
slices the counter index to 16 bits. As a result, on Spectrum-2 and above,
no more than about 410 RIF counters can be effectively used. This
translates to 205 netdevices for which L3 HW stats can be enabled. (This
does not happen on Spectrum-1, because there are fewer counters available
overall and the counter index never exceeds 16 bits.)
Binding counters to ACLs does not have this issue. Therefore reorder the
counter allocation scheme so that RIF counters come first and therefore get
lower indices that are below the 16-bit barrier.
Fixes: 98e60dce4da1 ("Merge branch 'mlxsw-Introduce-initial-Spectrum-2-support'")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220613125017.2018162-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The AMD XGbE driver currently counts the number of interrupts assigned
to the device by inspecting the pdev->resource array. Since commit
a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from DT
core") removed IRQs from this array, the driver now attempts to get all
interrupts from 1 to -1U and gives up probing once it reaches an invalid
interrupt index.
Obtain the number of IRQs with platform_irq_count() instead.
Fixes: a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from DT core")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220609161457.69614-1-jean-philippe@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixes: 6e144b47f560 (octeontx2-pf: Add support for adaptive interrupt coalescing)
Added support for VF interfaces as well.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_64BIT is not sufficient for checking for availability of
iowrite64() and friends.
Also, the out_addr helpers need to be inline.
Fixes: b690f8df6497 ("net: axienet: Use iowrite64 to write all 64b descriptor pointers")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to commit f735c40ed93c ("net: axienet: Autodetect 64-bit DMA
capability") and AXI-DMA spec (pg021), on 64-bit capable dma, only
writing MSB part of tail descriptor pointer causes DMA engine to start
fetching descriptors. However, we found that it is true only if dma is in
idle state. In other words, dma would use a tailp even if it only has LSB
updated, when the dma is running.
The non-atomicity of this behavior could be problematic if enough
delay were introduced in between the 2 writes. For example, if an
interrupt comes right after the LSB write and the cpu spends long
enough time in the handler for the dma to get back into idle state by
completing descriptors, then the seconcd write to MSB would treat dma
to start fetching descriptors again. Since the descriptor next to the
one pointed by current tail pointer is not filled by the kernel yet,
fetching a null descriptor here causes a dma internal error and halt
the dma engine down.
We suggest that the dma engine should start process a 64-bit MMIO write
to the descriptor pointer only if ONE 32-bit part of it is written on all
states. Or we should restrict the use of 64-bit addressable dma on 32-bit
platforms, since those devices have no instruction to guarantee the write
to LSB and MSB part of tail pointer occurs atomically to the dma.
initial condition:
curp = x-3;
tailp = x-2;
LSB = x;
MSB = 0;
cpu: |dma:
iowrite32(LSB, tailp) | completes #(x-3) desc, curp = x-3
... | tailp updated
=> irq | completes #(x-2) desc, curp = x-2
... | completes #(x-1) desc, curp = x-1
... | ...
... | completes #x desc, curp = tailp = x
<= irqreturn | reaches tailp == curp = x, idle
iowrite32(MSB, tailp + 4) | ...
| tailp updated, starts fetching...
| fetches #(x + 1) desc, sees cntrl = 0
| post Tx error, halt
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reported-by: Max Hsu <max.hsu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it is not safe to config the IP as 64-bit addressable on 32-bit
archectures, which cannot perform a double-word store on its descriptor
pointers. The pointer is 64-bit wide if the IP is configured as 64-bit,
and the device would process the partially updated pointer on some
states if the pointer was updated via two store-words. To prevent such
condition, we force a probe fail if we discover that the IP has 64-bit
capability but it is not running on a 64-Bit kernel.
This is a series of patch (1/2). The next patch must be applied in order
to make 64b DMA safe on 64b archectures.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reported-by: Max Hsu <max.hsu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
initialization
Currently in driver initialization process, driver will set shapping
parameters of tm port to default speed read from firmware. However, the
speed of SFP module may not be default speed, so shapping parameters of
tm port may be incorrect.
To fix this problem, driver sets new shapping parameters for tm port
after getting exact speed of SFP module in this case.
Fixes: 88d10bd6f730 ("net: hns3: add support for multiple media type")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently hns3 driver misuses the VF rss size to initialize the PF rss size
in hclge_tm_vport_tc_info_update. So this patch fix it by checking the
vport id before initialization.
Fixes: 7347255ea389 ("net: hns3: refactor PF rss get APIs with new common rss get APIs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, settings parameters of schedule mode, dwrr, shaper of tm
priority or qset of one tc are only be set when tc is enabled, they are
not restored to the default settings when tc is disabled. It confuses
users when they cat tm_priority or tm_qset files of debugfs. So this
patch fixes it.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently tx push is also a ring param. So the original ring param print
info in hns3_is_ringparam_changed should be adjusted.
Fixes: 07fdc163ac88 ("net: hns3: refactor hns3_set_ringparam()")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's unnecessary to push link state to unalive VF, and the VF will
query link state from PF when it being start works.
Fixes: 18b6e31f8bf4 ("net: hns3: PF add support for pushing link status to VFs")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When modify port base vlan, the port base vlan tbl_sta needs to set to
false before removing old vlan, to indicate this operation is not finish.
Fixes: c0f46de30c96 ("net: hns3: fix port base vlan add fail when concurrent with reset")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Highlights:
- Fix hp-wmi regression on HP Omen laptops introduced in 5.18
- Several hardware-id additions
- A couple of other tiny fixes"
* tag 'platform-drivers-x86-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/intel: hid: Add Surface Go to VGBS allow list
platform/x86: hp-wmi: Use zero insize parameter only when supported
platform/x86: hp-wmi: Resolve WMI query failures on some devices
platform/x86: gigabyte-wmi: Add support for B450M DS3H-CF
platform/x86: gigabyte-wmi: Add Z690M AORUS ELITE AX DDR4 support
platform/x86: barco-p50-gpio: Add check for platform_driver_register
platform/x86/intel: pmc: Support Intel Raptorlake P
platform/x86/intel: Fix pmt_crashlog array reference
platform/mellanox: Add static in struct declaration.
platform/mellanox: Spelling s/platfom/platform/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- A fix for a 5.19 regression for a case in which early device tree
initializes the RNG, which flips a static branch.
On most plaforms, jump labels aren't initialized until much later, so
this caused splats. On a few mailing list threads, we cooked up easy
fixes for arm64, arm32, and risc-v. But then things looked slightly
more involved for xtensa, powerpc, arc, and mips. And at that point,
when we're patching 7 architectures in a place before the console is
even available, it seems like the cost/risk just wasn't worth it.
So random.c works around it now by checking the already exported
`static_key_initialized` boolean, as though somebody already ran into
this issue in the past. I'm not super jazzed about that; it'd be
prettier to not have to complicate downstream code. But I suppose
it's practical.
- A few small code nits and adding a missing __init annotation.
- A change to the default config values to use the cpu and bootloader's
seeds for initializing the RNG earlier.
This brings them into line with what all the distros do (Fedora/RHEL,
Debian, Ubuntu, Gentoo, Arch, NixOS, Alpine, SUSE, and Void... at
least), and moreover will now give us test coverage in various test
beds that might have caught the above device tree bug earlier.
- A change to WireGuard CI's configuration to increase test coverage
around the RNG.
- A documentation comment fix to unrelated maintainerless CRC code that
I was asked to take, I guess because it has to do with polynomials
(which the RNG thankfully no longer uses).
* tag 'random-5.19-rc2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
wireguard: selftests: use maximum cpu features and allow rng seeding
random: remove rng_has_arch_random()
random: credit cpu and bootloader seeds by default
random: do not use jump labels before they are initialized
random: account for arch randomness in bits
random: mark bootloader randomness code as __init
random: avoid checking crng_ready() twice in random_init()
crc-itu-t: fix typo in CRC ITU-T polynomial comment
|
|
The Surface Go reports Chassis Type 9 (Laptop,) so the device needs to be
added to dmi_vgbs_allow_list to enable tablet mode when an attached Type
Cover is folded back.
BugLink: https://github.com/linux-surface/linux-surface/issues/837
Signed-off-by: Duke Lee <krnhotwings@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220607213654.5567-1-krnhotwings@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
commit be9d73e64957 ("platform/x86: hp-wmi: Fix 0x05 error code reported by
several WMI calls") and commit 12b19f14a21a ("platform/x86: hp-wmi: Fix
hp_wmi_read_int() reporting error (0x05)") cause ACPI BIOS Error (bug):
Attempt to CreateField of length zero (20211217/dsopcode-133) because of
the ACPI method HWMC, which unconditionally creates a Field of
size (insize*8) bits:
CreateField (Arg1, 0x80, (Local5 * 0x08), DAIN)
In cases where args->insize = 0, the Field size is 0, resulting in
an error.
Fix this by using zero insize only if 0x5 error code is returned
Tested on Omen 15 AMD (2020) board ID: 8786.
Fixes: be9d73e64957 ("platform/x86: hp-wmi: Fix 0x05 error code reported by several WMI calls")
Signed-off-by: Bedant Patnaik <bedant.patnaik@gmail.com>
Tested-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://lore.kernel.org/r/41be46743d21c78741232a47bbb5f1cdbcc3d21e.camel@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
WMI queries fail on some devices where the ACPI method HWMC
unconditionally attempts to create Fields beyond the buffer
if the buffer is too small, this breaks essential features
such as power profiles:
CreateByteField (Arg1, 0x10, D008)
CreateByteField (Arg1, 0x11, D009)
CreateByteField (Arg1, 0x12, D010)
CreateDWordField (Arg1, 0x10, D032)
CreateField (Arg1, 0x80, 0x0400, D128)
In cases where args->data had zero length, ACPI BIOS Error
(bug): AE_AML_BUFFER_LIMIT, Field [D008] at bit
offset/length 128/8 exceeds size of target Buffer (128 bits)
(20211217/dsopcode-198) was obtained.
ACPI BIOS Error (bug): AE_AML_BUFFER_LIMIT, Field [D009] at bit
offset/length 136/8 exceeds size of target Buffer (136bits)
(20211217/dsopcode-198)
The original code created a buffer size of 128 bytes regardless if
the WMI call required a smaller buffer or not. This particular
behavior occurs in older BIOS and reproduced in OMEN laptops. Newer
BIOS handles buffer sizes properly and meets the latest specification
requirements. This is the reason why testing with a dynamically
allocated buffer did not uncover any failures with the test systems at
hand.
This patch was tested on several OMEN, Elite, and Zbooks. It was
confirmed the patch resolves HPWMI_FAN GET/SET calls in an OMEN
Laptop 15-ek0xxx. No problems were reported when testing on several Elite
and Zbooks notebooks.
Fixes: 4b4967cbd268 ("platform/x86: hp-wmi: Changing bios_args.data to be dynamically allocated")
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220608212923.8585-2-jorge.lopez2@hp.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A set of fixes. Most address the new warning we emit at build time
when irq chips are not immutable with some additional tweaks to
gpio-crystalcove from Andy and a small tweak to gpio-dwapd.
- make irq_chip structs immutable in several Diolan and intel drivers
to get rid of the new warning we emit when fiddling with irq chips
- don't print error messages on probe deferral in gpio-dwapb"
* tag 'gpio-fixes-for-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: dwapb: Don't print error on -EPROBE_DEFER
gpio: dln2: make irq_chip immutable
gpio: sch: make irq_chip immutable
gpio: merrifield: make irq_chip immutable
gpio: wcove: make irq_chip immutable
gpio: crystalcove: Join function declarations and long lines
gpio: crystalcove: Use specific type and API for IRQ number
gpio: crystalcove: make irq_chip immutable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Driver fixes and and one core patch.
Nine of the driver patches are minor fixes and reworks to lpfc and the
rest are trivial and minor fixes elsewhere"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pmcraid: Fix missing resource cleanup in error case
scsi: ipr: Fix missing/incorrect resource cleanup in error case
scsi: mpt3sas: Fix out-of-bounds compiler warning
scsi: lpfc: Update lpfc version to 14.2.0.4
scsi: lpfc: Allow reduced polling rate for nvme_admin_async_event cmd completion
scsi: lpfc: Add more logging of cmd and cqe information for aborted NVMe cmds
scsi: lpfc: Fix port stuck in bypassed state after LIP in PT2PT topology
scsi: lpfc: Resolve NULL ptr dereference after an ELS LOGO is aborted
scsi: lpfc: Address NULL pointer dereference after starget_to_rport()
scsi: lpfc: Resolve some cleanup issues following SLI path refactoring
scsi: lpfc: Resolve some cleanup issues following abort path refactoring
scsi: lpfc: Correct BDE type for XMIT_SEQ64_WQE in lpfc_ct_reject_event()
scsi: vmw_pvscsi: Expand vcpuHint to 16 bits
scsi: sd: Fix interpretation of VPD B9h length
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes all over the place, most notably fixes for latent bugs in
drivers that got exposed by suppressing interrupts before DRIVER_OK,
which in turn has been done by 8b4ec69d7e09 ("virtio: harden vring
IRQ")"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
um: virt-pci: set device ready in probe()
vdpa: make get_vq_group and set_group_asid optional
virtio: Fix all occurences of the "the the" typo
vduse: Fix NULL pointer dereference on sysfs access
vringh: Fix loop descriptors check in the indirect cases
vdpa/mlx5: clean up indenting in handle_ctrl_vlan()
vdpa/mlx5: fix error code for deleting vlan
virtio-mmio: fix missing put_device() when vm_cmdline_parent registration failed
vdpa/mlx5: Fix syntax errors in comments
virtio-rng: make device ready before making request
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-09
Grzegorz prevents addition of TC flower filters to TC0 and fixes queue
iteration for VF ADQ to number of actual queues for i40e.
Aleksandr prevents running of ethtool tests when device is being reset
for i40e.
Michal resolves an issue where iavf does not report its MAC address
properly.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix issue with MAC address of VF shown as zero
i40e: Fix call trace in setup_tx_descriptors
i40e: Fix calculating the number of queue pairs
i40e: Fix adding ADQ filter to TC0
====================
Link: https://lore.kernel.org/r/20220609162620.2619258-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM core's bioset initialization so that blk integrity pool is
properly setup. Remove now unused bioset_init_from_src.
- Fix DM zoned hang from locking imbalance due to needless check in
clone_endio().
* tag 'for-5.19/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix zoned locking imbalance due to needless check in clone_endio
block: remove bioset_init_from_src
dm: fix bio_set allocation
|
|
Tested and works on my system.
Signed-off-by: August Wikerfors <git@augustwikerfors.se>
Link: https://lore.kernel.org/r/20220608212028.28307-1-git@augustwikerfors.se
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add dmi_system_id of Gigabyte Z690M AORUS ELITE AX DDR4 board.
Tested on my PC.
Signed-off-by: Piotr Chmura <chmooreck@gmail.com>
Link: https://lore.kernel.org/r/bd83567e-ebf5-0b31-074b-5f6dc7f7c147@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 86af1d02d458 ("platform/x86: Support for EC-connected GPIOs for identify LED/button on Barco P50 board")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Link: https://lore.kernel.org/r/20220526090345.1444172-1-jiasheng@iscas.ac.cn
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add Raptorlake P to the list of the platforms that intel_pmc_core driver
supports for pmc_core device. Raptorlake P PCH is based on Alderlake P
PCH.
Signed-off-by: George D Sworo <george.d.sworo@intel.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220602012617.20100-1-george.d.sworo@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The probe function pmt_crashlog_probe() may incorrectly reference
the 'priv->entry array' as it uses 'i' to reference the array instead
of 'priv->num_entries' as it should. This is similar to the problem
that was addressed in pmt_telemetry_probe via commit 2cdfa0c20d58
("platform/x86/intel: Fix 'rmmod pmt_telemetry' panic").
Cc: "David E. Box" <david.e.box@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <markgross@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David Arcari <darcari@redhat.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220526203140.339120-1-darcari@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
