| Age | Commit message (Collapse) | Author |
|---|
|
Revert commit 4ef451487019 (cpufreq: intel_pstate: Avoid calculation for
max/min) as it depends on commit 37afb0003242 (cpufreq: intel_pstate: Use
ACPI perf configuration) that causes problems to happen and needs to be
reverted.
Conflicts:
drivers/cpufreq/intel_pstate.c
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is wrong to use do_div() with 32-bit dividends (unsigned long is
32 bits on 32-bit architectures).
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
gov_queue_work() acquires cpufreq_governor_lock to allow
cpufreq_governor_stop() to drain delayed work items possibly scheduled
on CPUs that share the policy with a CPU being taken offline.
However, the same goal may be achieved in a more straightforward way if
the policy pointer in the struct cpu_dbs_info matching the policy CPU is
reset upfront by cpufreq_governor_stop() under the timer_mutex belonging
to it and checked against NULL, under the same lock, at the beginning of
dbs_timer().
In that case every instance of dbs_timer() run for a struct cpu_dbs_info
sharing the policy pointer in question after cpufreq_governor_stop() has
started will notice that that pointer is NULL and bail out immediately
without queuing up any new work items. In turn, gov_cancel_work()
called by cpufreq_governor_stop() before destroying timer_mutex will
wait for all of the delayed work items currently running on the CPUs
sharing the policy to drop the mutex, so it may be destroyed safely.
Make cpufreq_governor_stop() and dbs_timer() work as described and
modify gov_queue_work() so it does not acquire cpufreq_governor_lock any
more.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When booting an HWP enabled system the kernel displays one "HWP enabled"
message for each cpu. The messages are superfluous since HWP is globally
enabled across all CPUs. This patch also adds an informational message
when HWP is disabled via intel_pstate=no_hwp.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The check for correct frequency being set in bL_cpufreq_set_rate is
broken when the big.LITTLE switcher is active, for two reasons.
1. The 'new_rate' variable gets overwritten before the test by the
code calculating the frequency of the old cluster.
2. The frequency returned by bL_cpufreq_get_rate will be the virtual
frequency, not the actual one the intended version of new_rate contains.
This means the function always returns an error causing an endless
stream of: "cpufreq: __target_index: Failed to change cpu frequency: -5"
As the intent is to check for errors that clk_set_rate doesn't report
lets move the check to immediately after that and directly use
clk_get_rate, rather than the arm_big_little helpers which only confuse
matters. Also, update the comment to be hopefully clearer about the
purpose of the code.
Fixes: 0a95e630b49a (cpufreq: arm_big_little: check if the frequency is set correctly)
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The sysfs policy directory is postfixed currently with the CPU number
for which the policy was created, which isn't necessarily the first CPU
in related_cpus mask.
To make it more consistent and predictable, lets postfix the policy with
the first cpu in related-cpus mask.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq sysfs interface had been a bit inconsistent as one of the
CPUs for a policy had a real directory within its sysfs 'cpuX' directory
and all other CPUs had links to it. That also made the code a bit
complex as we need to take care of moving the sysfs directory if the CPU
containing the real directory is getting physically hot-unplugged.
Solve this by creating 'policyX' directories (per-policy) in
/sys/devices/system/cpu/cpufreq/ directory, where X is the CPU for which
the policy was first created.
This also removes the need of keeping kobj_cpu and we can remove it now.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: is more of a general agreement from the person that he is
Reviewed-by: is a more strict tag and implies that the reviewer has
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
They don't do anything special now, remove the unnecessary wrapper.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Later patches will need to create policy specific directories in
/sys/devices/system/cpu/cpufreq/ directory and so the cpufreq directory
wouldn't be ever empty.
And so no fun creating/destroying it on need basis anymore. Create it
once on system boot.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
->related_cpus is empty at this point of time and copying ->cpus to it
or orring ->related_cpus with ->cpus would result in the same value. But
cpumask_copy makes it rather clear.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
'timer_mutex' is required to sync work-handlers of policy->cpus.
update_sampling_rate() is just canceling the works and queuing them
again. This isn't protecting anything at all in update_sampling_rate()
and is not gonna be of any use.
Even if a work-handler is already running for a CPU,
cancel_delayed_work_sync() will wait for it to finish.
Drop these unnecessary locks.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On systems that initialize the intel_pstate driver with the performance
governor, and then switch to the powersave governor will not transition to
lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct
is set to a low value.
The behavior of governor switching changed after commit a04759924e25
("[cpufreq] intel_pstate: honor user space min_perf_pct override on
resume"). The commit introduced tracking of performance percentage
changes via sysfs in order to restore userspace changes during
suspend/resume. The problem occurs because the global values of the newly
introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor
change and this causes the powersave governor to inherit the performance
governor's settings.
A simple change would have been to reset max_sysfs_pct to 100 and
min_sysfs_pct to 0 on a governor change, which fixes the problem with
governor switching. However, since we cannot break userspace[1] the fix
is now to give each governor its own limits storage area so that governor
specific changes are tracked.
I successfully tested this by booting with both the performance governor
and the powersave governor by default, and switching between the two
governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values,
and looking at the output of cpupower frequency-info). Suspend/Resume
testing was performed by Doug Smythies.
[1] Systems which suspend/resume using the unmaintained pm-utils package
will always transition to the performance governor before the suspend and
after the resume. This means a system using the powersave governor will
go from powersave to performance, then suspend/resume, performance to
powersave. The simple change during governor changes would have been
overwritten when the governor changed before and after the suspend/resume.
I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225
against Fedora to remove the 94cpufreq file that causes the problem. It
should be noted that pm-utils is obsoleted with newer versions of systemd.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When requested from cpufreq to set policy, look into _pss and get
control values, instead of using max/min perf calculations. These
calculation misses next control state in boundary conditions.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use ACPI _PSS to limit the Intel P State turbo, max and min ratios.
This driver uses acpi processor perf lib calls to register performance.
The following logic is used to adjust Intel P state driver limits:
- If there is no turbo entry in _PSS, then disable Intel P state turbo
and limit to non turbo max
- If the non turbo max ratio is more than _PSS max non turbo value, then
set the max non turbo ratio to _PSS non turbo max
- If the min ratio is less than _PSS min then change the min ratio
matching _PSS min
- Scale the _PSS turbo frequency to max turbo frequency based on control
value.
This feature can be disabled by using kernel parameters:
intel_pstate=no_acpi
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Systems with configurable TDP have multiple max non turbo p state. Intel
P state uses max non turbo P state for scaling. But using the real max
non turbo p state causes underestimation of next P state. So using
the physical max non turbo P state as before for scaling.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After Ivybridge, the max non turbo ratio obtained from platform info msr
is not always guaranteed P1 on client platforms. The max non turbo
activation ratio (TAR), determines the max for the current level of TDP.
The ratio in platform info is physical max. The TAR MSR can be locked,
so updating this value is not possible on all platforms.
This change gets this ratio from MSR TURBO_ACTIVATION_RATIO if
available,
but also do some sanity checking to make sure that this value is
correct.
The sanity check involves reading the TDP ratio for the current tdp
control value when platform has configurable TDP present and matching
TAC
with this.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We just made sure policy->cpu is online and this check will always fail
as the policy is active. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three bug fixes, two of which are regressions from
recent updates (the 3ware one from 4.1 and the device handler fixes
from 4.2)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: don't unmap bounce buffered commands
scsi_dh: Use the correct module name when loading device handler
libiscsi: Fix iscsi_check_transport_timeouts possible infinite loop
|
|
Pull md bugfix from Neil Brown:
"One bug fix for raid1/raid10.
Very careless bug earler in 4.3-rc, now fixed :-)"
* tag 'md/4.3-rc4-fix' of git://neil.brown.name/md:
crash in md-raid1 and md-raid10 due to incorrect list manipulation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these
have been in linux-next for a while"
* tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: Add device quirk for Logitech PTZ cameras
USB: chaoskey read offset bug
USB: Add reset-resume quirk for two Plantronics usb headphones.
usb: renesas_usbhs: Add support for R-Car H3
usb: renesas_usbhs: fix build warning if 64-bit architecture
usb: gadget: bdc: fix memory leak
phy: berlin-sata: Fix module autoload for OF platform driver
phy: rockchip-usb: power down phy when rockchip phy probe
phy: qcom-ufs: fix build error when the component is built as a module
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a few bug fixes for the tty core that resolve reported
issues, and some serial driver fixes as well (including the
much-reported imx driver problem)
All of these have been in linux-next with no reported problems"
* tag 'tty-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
drivers/tty: require read access for controlling terminal
serial: 8250: add uart_config entry for PORT_RT2880
tty: fix data race on tty_buffer.commit
tty: fix data race in tty_buffer_flush
tty: fix data race in flush_to_ldisc
tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.c
serial: atmel: fix error path of probe function
tty: don't leak cdev in tty_cdev_add()
Revert "serial: imx: remove unbalanced clk_prepare"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two tiny staging tree fixes for 4.3-rc5.
One fixes the broken speakup subsystem as reported by a user, and the
other removes an entry in the MAINTAINERS file for a developer that
doesn't want to be listed anymore"
* tag 'staging-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: speakup: fix speakup-r regression
MAINTAINERS: Remove myself as nvec co-maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small fixes for some misc drivers that resolve some
reported issues. All of these have been linux-next for a while"
* tag 'char-misc-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mcb: Fix error handling in mcb_pci_probe()
mei: hbm: fix error in state check logic
nvmem: sunxi: Check for memory allocation failure
nvmem: core: Fix memory leak in nvmem_cell_write
nvmem: core: Handle shift bits in-place if cell->nbits is non-zero
nvmem: core: fix the out-of-range leak in read/write()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are four fixes for bugs in the devfreq and cpufreq subsystems,
including two regression fixes (one for a recent regression and one
for a problem introduced in 4.2).
Specifics:
- Two fixes for cpufreq regressions, an acpi-cpufreq driver one
introduced during the 4.2 cycle when we started to preserve cpufreq
directories for offline CPUs and a general one introduced recently
(Srinivas Pandruvada).
- Two devfreq fixes, one for a double kfree() in an error code path
and one for a confusing sysfs-related failure (Geliang Tang, Tobias
Jakobi)"
* tag 'pm+acpi-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: prevent lockup on reading scaling_available_frequencies
cpufreq: acpi_cpufreq: prevent crash on reading freqdomain_cpus
PM / devfreq: fix double kfree
PM / devfreq: Fix governor_store()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A Samsung driver fix and a handful of TI driver fixes"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: dflt: fix enable_reg validity check
clk: ti: fix dual-registration of uart4_ick
clk: ti: clk-7xx: Remove hardwired ABE clock configuration
clk: samsung: fix cpu clock's flags checking
|
|
Pull MMC fixes from Ulf Hansson:
"MMC host:
- omap_hsmmc: Fix boot regressions for omap4430
- omap_hsmmc: Fix legacy boot regression for omap3
- sdhci-pxav3: Fix some clock issues for Armada 38x
- sdhci-pxav3: Fix error handling at probe
- sdhci-of-at91: Fix clock stabilization problem"
* tag 'mmc-v4.3-rc4' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-of-at91: use SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk
mmc: sdhci: add quirk SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST
mmc: sdhci-pxav3: fix error handling of armada_38x_quirks
mmc: sdhci-pxav3: disable clock inversion for HS MMC cards
mmc: sdhci-pxav3: remove broken clock base quirk for Armada 38x sdhci driver
mmc: host: omap_hsmmc: Fix MMC for omap3 legacy booting
Revert "mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull dm fixes from Mike Snitzer:
"Three stable fixes:
- DM core AB-BA deadlock fix in the device destruction path (vs
device creation's DM table swap).
- DM raid fix to properly round up the region_size to the next
power-of-2.
- DM cache fix for a NULL pointer seen while switching from the
"cleaner" cache policy.
Two fixes for regressions introduced during the 4.3 merge:
- request-based DM error propagation regressed due to incorrect
changes introduced when adding the bi_error field to bio.
- DM snapshot fix to only support snapshots that overflow if the
client (e.g. lvm2) is prepared to deal with the associated
snapshot status interface change"
* tag 'dm-4.3-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: add new persistent store option to support overflow
dm cache: fix NULL pointer when switching from cleaner policy
dm: fix request-based dm error reporting
dm raid: fix round up of default region size
dm: fix AB-BA deadlock in __dm_destroy()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"The fixes for this week include one small patch that was years in the
making and that finally fixes using all eight CPUs on exynos542x.
The rest are lots of minor changes for sunxi, imx, exynos and shmobile
- fixing the minimum voltage for Allwinner A20
- thermal boot issue on SMDK5250.
- invalid clock used for FIMD IOMMU.
- audio on Renesas r8a7790/r8a7791
- invalid clock used for FIMD IOMMU
- LEDs on exynos5422-odroidxu3-common
- usb pin control for imx-rex
- imx53: fix PMIC interrupt level
- a Makefile typo"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
ARM: dts: Fix bootup thermal issue on smdk5250
ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
arm-cci500: Don't enable PMU driver by default
ARM: dts: fix usb pin control for imx-rex dts
ARM: imx53: qsrb: fix PMIC interrupt level
ARM: imx53: include IRQ dt-bindings header
ARM: dts: add suspend opp to exynos4412
ARM: dts: Fix LEDs on exynos5422-odroidxu3
ARM: EXYNOS: reset Little cores when cpu is up
ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications
|
|
Commit 76c44f6d80 introduced the possibly for "Overflow" to be reported
by the snapshot device's status. Older userspace (e.g. lvm2) does not
handle the "Overflow" status response.
Fix this incompatibility by requiring newer userspace code, that can
cope with "Overflow", request the persistent store with overflow support
by using "PO" (Persistent with Overflow) for the snapshot store type.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Fixes: 76c44f6d80 ("dm snapshot: don't invalidate on-disk image on snapshot write overflow")
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
* pm-devfreq:
PM / devfreq: fix double kfree
PM / devfreq: Fix governor_store()
* pm-cpufreq:
cpufreq: prevent lockup on reading scaling_available_frequencies
cpufreq: acpi_cpufreq: prevent crash on reading freqdomain_cpus
|
|
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
The commit 55ce74d4bfe1b9444436264c637f39a152d1e5ac (md/raid1: ensure
device failure recorded before write request returns) is causing crash in
the LVM2 testsuite test shell/lvchange-raid.sh. For me the crash is 100%
reproducible.
The reason for the crash is that the newly added code in raid1d moves the
list from conf->bio_end_io_list to tmp, then tests if tmp is non-empty and
then incorrectly pops the bio from conf->bio_end_io_list (which is empty
because the list was alrady moved).
Raid-10 has a similar bug.
Kernel Fault: Code=15 regs=000000006ccb8640 (Addr=0000000100000000)
CPU: 3 PID: 1930 Comm: mdX_raid1 Not tainted 4.2.0-rc5-bisect+ #35
task: 000000006cc1f258 ti: 000000006ccb8000 task.ti: 000000006ccb8000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111111000001111 Not tainted
r00-03 000000ff0804fe0f 000000001059d000 000000001059f818 000000007f16be38
r04-07 000000001059d000 000000007f16be08 0000000000200200 0000000000000001
r08-11 000000006ccb8260 000000007b7934d0 0000000000000001 0000000000000000
r12-15 000000004056f320 0000000000000000 0000000000013dd0 0000000000000000
r16-19 00000000f0d00ae0 0000000000000000 0000000000000000 0000000000000001
r20-23 000000000800000f 0000000042200390 0000000000000000 0000000000000000
r24-27 0000000000000001 000000000800000f 000000007f16be08 000000001059d000
r28-31 0000000100000000 000000006ccb8560 000000006ccb8640 0000000000000000
sr00-03 0000000000249800 0000000000000000 0000000000000000 0000000000249800
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 000000001059f61c 000000001059f620
IIR: 0f8010c6 ISR: 0000000000000000 IOR: 0000000100000000
CPU: 3 CR30: 000000006ccb8000 CR31: 0000000000000000
ORIG_R28: 000000001059d000
IAOQ[0]: call_bio_endio+0x34/0x1a8 [raid1]
IAOQ[1]: call_bio_endio+0x38/0x1a8 [raid1]
RP(r2): raid_end_bio_io+0x88/0x168 [raid1]
Backtrace:
[<000000001059f818>] raid_end_bio_io+0x88/0x168 [raid1]
[<00000000105a4f64>] raid1d+0x144/0x1640 [raid1]
[<000000004017fd5c>] kthread+0x144/0x160
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 55ce74d4bfe1 ("md/raid1: ensure device failure recorded before write request returns.")
Fixes: 95af587e95aa ("md/raid10: ensure device failure recorded before write request returns.")
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
When scaling_available_frequencies is read on an offlined cpu, then
either lockup or junk values are displayed. This is caused by
freed freq_table, which policy is using.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When freqdomain_cpus attribute is read from an offlined cpu, it will
cause crash. This change prevents calling cpufreq_show_cpus when
policy driver_data is NULL.
Crash info:
[ 170.814949] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
[ 170.814990] IP: [<ffffffff813b2490>] _find_next_bit.part.0+0x10/0x70
[ 170.815021] PGD 227d30067 PUD 229e56067 PMD 0
[ 170.815043] Oops: 0000 [#2] SMP
[ 170.816022] CPU: 3 PID: 3121 Comm: cat Tainted: G D OE 4.3.0-rc3+ #33
...
...
[ 170.816657] Call Trace:
[ 170.816672] [<ffffffff813b2505>] ? find_next_bit+0x15/0x20
[ 170.816696] [<ffffffff8160e47c>] cpufreq_show_cpus+0x5c/0xd0
[ 170.816722] [<ffffffffa031a409>] show_freqdomain_cpus+0x19/0x20 [acpi_cpufreq]
[ 170.816749] [<ffffffff8160e65b>] show+0x3b/0x60
[ 170.816769] [<ffffffff8129b31c>] sysfs_kf_seq_show+0xbc/0x130
[ 170.816793] [<ffffffff81299be3>] kernfs_seq_show+0x23/0x30
[ 170.816816] [<ffffffff81240f2c>] seq_read+0xec/0x390
[ 170.816837] [<ffffffff8129a64a>] kernfs_fop_read+0x10a/0x160
[ 170.816861] [<ffffffff8121d9b7>] __vfs_read+0x37/0x100
[ 170.816883] [<ffffffff813217c0>] ? security_file_permission+0xa0/0xc0
[ 170.816909] [<ffffffff8121e2e3>] vfs_read+0x83/0x130
[ 170.816930] [<ffffffff8121f035>] SyS_read+0x55/0xc0
...
...
[ 170.817185] ---[ end trace bc6eadf82b2b965a ]---
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.2+ <stable@vger.kernel.org> # 4.2+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Atmel sdhci device needs the
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the
internal clock could never stabilised when changing the sd clock
frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of armada_38x_quirks error, all clocks should be cleaned-up, same
as after mv_conf_mbus_windows failure.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Starting with commit 7d607f917008 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc") MMC on omap3 stopped working
for legacy booting.
This is because legacy booting sets up some of the resource in the
platform init code, and for optional regulators always seem to
return -EPROBE_DEFER for the legacy booting.
Let's fix the issue by checking for device tree based booting for
now. Then when omap3 boots in device tree only mode, this patch
can be just reverted.
Fixes: 7d607f917008 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit c55d7a0553643a7e8f120688b82b594471084d3c.
Without reverting this commit we get "unbalanced disables for pbias_mmc_omap4"
errors on omap4430. It seems that 4430 and 4460 behave in a different way for
the PBIAS regulator registers and until that has been debugged further we
cannot rely on the regulator status registers in hardare on 4430.
Fixes: 7d607f917008 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- fbdev: Minor fixes to broadsheetfb, fsl-diu-fb, mb862xxfb, tridentfb,
omapfb
- display-timing: Fix memory leak in error path
* tag 'fbdev-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: of: fix memory leak
fbdev: broadsheetfb: fix memory leak
OMAPDSS: panel-sony-acx565akm: Export OF module alias information
fbdev: omap2: connector-dvi: use of_get_i2c_adapter_by_node interface
tridentfb: Fix set_lwidth on TGUI9440 and CYBER9320
tridentfb: fix hang on Blade3D with CONFIG_CC_OPTIMIZE_FOR_SIZE
video: fbdev: mb862xx: Fix module autoload for OF platform driver
video: fbdev: fsl: Fix the sleep function for FSL DIU module
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A couple of fixes for the debugfs information on the register map,
fixing issues with very small reads potentially causing underflows and
wraparounds"
* tag 'regmap-fix-v4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: debugfs: Don't bother actually printing when calculating max length
regmap: debugfs: Ensure we don't underflow when printing access masks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of very minor fixes, one for error handling in the Davinci
driver probe function and another making the Renesas sh-msiof DT
binding documentation correspond to what's actually implemented"
* tag 'spi-fix-v4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sh-msiof: Match renesas,rx-fifo-size in DT bindings doc with driver
spi: davinci: fix handling platform_get_irq result
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Two fixes here, one device specific fix for axp20x and a core fix for
cases where one regulator is supplying another which broke probe
deferral, substituting in a dummy regulator too aggressively"
* tag 'regulator-fix-v4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Handle probe deferral from DT when resolving supplies
regulator: axp20x: Fix enable bit indexes for DCDC4 and DCDC5
|
|
If of_parse_display_timing() fails we are printing an error message and
jumping to the error path but we missed freeing "dt".
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
