| Age | Commit message (Collapse) | Author |
|---|
|
'clk-socfpga-parent' and 'clk-struct-size' into clk-next
- Various DT of_node refcount fixes
- Support for fixed rate clks populated from an MMIO register
- Remove clps711x driver as the board support is gone
* clk-of-refcount:
clk: dove: fix refcount leak in dove_clk_init()
clk: mv98dx3236: fix refcount leak in mv98dx3236_clk_init()
clk: armada-xp: fix refcount leak in axp_clk_init()
clk: kirkwood: fix refcount leak in kirkwood_clk_init()
clk: armada-370: fix refcount leak in a370_clk_init()
clk: vf610: fix refcount leak in vf610_clocks_init()
clk: imx7d: fix refcount leak in imx7d_clocks_init()
clk: imx6sx: fix refcount leak in imx6sx_clocks_init()
clk: imx6q: fix refcount leak in imx6q_clocks_init()
clk: samsung: exynos4: fix refcount leak in exynos4_get_xom()
clk: socfpga: fix refcount leak
clk: ti: fix refcount leak in ti_dt_clocks_register()
clk: qoriq: fix refcount leak in clockgen_init()
clk: highbank: fix refcount leak in hb_clk_init()
* clk-mmio-fixed-clock:
clk: Add Fixed MMIO clock driver
dt-bindings: clk: Add bindings for Fixed MMIO clock
* clk-remove-clps:
clk: clps711x: Remove board support
* clk-socfpga-parent:
clk: socfpga: Don't have get_parent for single parent ops
* clk-struct-size:
clk: imx: imx7ulp: use struct_size() in kzalloc()
|
|
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
|
|
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
|
|
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
? 0xffffffffc0e40000
? 0xffffffffc0e40000
? 0xffffffffc0e40000
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
Allocated by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
kmalloc include/linux/slab.h:545 [inline]
kzalloc include/linux/slab.h:740 [inline]
mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kfree+0xe1/0x270 mm/slub.c:3938
device_release+0x78/0x200 drivers/base/core.c:919
kobject_cleanup lib/kobject.c:662 [inline]
kobject_release lib/kobject.c:691 [inline]
kref_put include/linux/kref.h:67 [inline]
kobject_put+0x146/0x240 lib/kobject.c:708
put_device+0x1c/0x30 drivers/base/core.c:2060
__mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881dc824c80
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The intended optimization should be A ^ 0 = A, not A ^ -1 = A.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To communicate to PF each of ThunderX NIC VF uses mailbox which is
pair of 64 bit registers available to both VFn and PF.
This commit is to change the xcast message structure in order to
fit it into 64 bit.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
private for each of them.
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct STREERING to STEERING at macro name for BGX steering register.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.
Fixes: f1d22a1e0595 ("team: account for oper state")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.
Signed-off-by: David Chen <david.chen7@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.
This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
* Spawn container & change ipvlan mode setting inside of it:
# docker run -dt --cap-add=NET_ADMIN --network cilium-net --name client -l app=test cilium/netperf
9fff485d69dcb5ce37c9e33ca20a11ccafc236d690105aadbfb77e4f4170879c
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
# docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns (mode switched to l2):
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:
# docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"This contains a single i915 tiled display fix, and a set of
amdgpu/radeon fixes.
i915:
- tiled display fix
amdgpu/radeon:
- runtime PM fix
- bulk moves disable (fix is too large for 5.0)
- a set of display fixes that are all cc'ed stable so we didn't want
to leave them until -next"
* tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: disable bulk moves for now
drm/amd/display: set clocks to 0 on suspend on dce80
drm/amd/display: fix optimize_bandwidth func pointer for dce80
drm/amd/display: Fix negative cursor pos programming
drm/i915/fbdev: Actually configure untiled displays
drm/amd/display: Raise dispclk value for dce11
drm/amd/display: Fix MST reboot/poweroff sequence
drm/amdgpu: Update sdma golden setting for vega20
drm/amdgpu: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
gpu: drm: radeon: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
|
|
Pull rdma fixes from Jason Gunthorpe:
"Small set of three regression fixing patches, things are looking
pretty good here.
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
iw_cxgb4: cq/qp mask depends on bar2 pages in a host page
cxgb4: Export sge_host_page_size to ulds
RDMA/srp: Rework SCSI device reset handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few more fixes for clk drivers causing regressions this release.
Two Allwinner index fixes for A31 and V3 and two Microchip AT91 fixes
for an incorrect clk parent linkage and a miscalculated number of
clks"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: fix masterck name
clk: at91: fix at91sam9x5 peripheral clock number
clk: sunxi: A31: Fix wrong AHB gate number
clk: sunxi-ng: v3s: Fix TCON reset de-assert bit
|
|
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
* pm-cpufreq-fixes:
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
|
|
into drm-fixes
A bit bigger than normal for this week due to fixes for some long
standing display issues that are bound for stable. These changes would
be going to stable anyway, so I figured it was better via 5.0 than 5.1.
- Several display fixes
- Fix PX systems due to core changes in runtime pm
- Disable bulk moves. They are fixed in 5.1, but fix is too invasive for 5.0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220225715.3240-1-alexander.deucher@amd.com
|
|
This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:
6a9e461f6fe4 bonding: pass link-local packets to bonding master also.
... to:
b89f04c61efe bonding: deliver link-local packets with skb->dev set to link that packets arrived on
While 6a9e461f6fe4 restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.
Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.
At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.
This elegantly solves all issues so far:
- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces
Fixes: 6a9e461f6fe4 (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similiar to commit e94cd8113ce63 ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An issue has been found while testing zero-copy XDP that
causes a reset to be triggered. As it takes some time to
turn the carrier on after setting zc, and we already
start trying to transmit some packets, watchdog considers
this as an erroneous state and triggers a reset.
Don't do any work if netif carrier is not OK.
Fixes: 8221c5eba8c13 (ixgbe: add AF_XDP zero-copy Tx support)
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the driver clears the XDP xmit ring due to re-configuration or
teardown, in-progress ndo_xdp_xmit must be taken into consideration.
The ndo_xdp_xmit function is typically called from a NAPI context that
the driver does not control. Therefore, we must be careful not to
clear the XDP ring, while the call is on-going. This patch adds a
synchronize_rcu() to wait for napi(s) (preempt-disable regions and
softirqs), prior clearing the queue. Further, the __I40E_CONFIG_BUSY
flag is checked in the ndo_xdp_xmit implementation to avoid touching
the XDP xmit queue during re-configuration.
Fixes: d9314c474d4f ("i40e: add support for XDP_REDIRECT")
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers so
that packets can be received. Usually these are kernel buffers, but
for AF_XDP in zero-copy mode, these are user-space buffers and in this
case the application might not have sent down any buffers to the
driver at this point. And if no buffers are allocated at ring creation
time, no packets can be received and no interrupts will be generated so
the NAPI poll function that allocates buffers to the rings will never
get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once after
an XDP program has loaded and once after the umem is registered. This
take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The enabling L3/L4 filtering for transmit switched packets for all
devices caused unforeseen issue on older devices when trying to send UDP
traffic in an ordered sequence. This bit was originally intended for X550
devices, which supported this feature, so limit the scope of this bit to
only X550 devices.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
When rpm_resume() desactivates the autosuspend timer, it should only
try to cancel hrtimer but not wait for the handler to finish, because
both rpm_resume() and pm_suspend_timer_fn() take the power.lock.
A deadlock is possible as follows:
CPU0 CPU1
rpm_resume()
spin_lock_irqsave
pm_suspend_timer_fn()
spin_lock_irqsave
pm_runtime_deactivate_timer()
hrtimer_cancel()
It is sufficient to call hrtimer_try_to_cancel() from
pm_runtime_deactivate_timer(), because dev->power.timer_expires
reset to 0 by it, so use that function instead of hrtimer_cancel().
Fixes: 8234f6734c5d ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Sunzhaosheng Sun(Zhaosheng) <sunzhaosheng@hisilicon.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Booting 4.20 on SolidRun Clearfog issues this warning with DMA API
debug enabled:
WARNING: CPU: 0 PID: 555 at kernel/dma/debug.c:1230 check_sync+0x514/0x5bc
mvneta f1070000.ethernet: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000002dd7dc00] [size=240 bytes]
Modules linked in: ahci mv88e6xxx dsa_core xhci_plat_hcd xhci_hcd devlink armada_thermal marvell_cesa des_generic ehci_orion phy_armada38x_comphy mcp3021 spi_orion evbug sfp mdio_i2c ip_tables x_tables
CPU: 0 PID: 555 Comm: bridge-network- Not tainted 4.20.0+ #291
Hardware name: Marvell Armada 380/385 (Device Tree)
[<c0019638>] (unwind_backtrace) from [<c0014888>] (show_stack+0x10/0x14)
[<c0014888>] (show_stack) from [<c07f54e0>] (dump_stack+0x9c/0xd4)
[<c07f54e0>] (dump_stack) from [<c00312bc>] (__warn+0xf8/0x124)
[<c00312bc>] (__warn) from [<c00313b0>] (warn_slowpath_fmt+0x38/0x48)
[<c00313b0>] (warn_slowpath_fmt) from [<c00b0370>] (check_sync+0x514/0x5bc)
[<c00b0370>] (check_sync) from [<c00b04f8>] (debug_dma_sync_single_range_for_cpu+0x6c/0x74)
[<c00b04f8>] (debug_dma_sync_single_range_for_cpu) from [<c051bd14>] (mvneta_poll+0x298/0xf58)
[<c051bd14>] (mvneta_poll) from [<c0656194>] (net_rx_action+0x128/0x424)
[<c0656194>] (net_rx_action) from [<c000a230>] (__do_softirq+0xf0/0x540)
[<c000a230>] (__do_softirq) from [<c00386e0>] (irq_exit+0x124/0x144)
[<c00386e0>] (irq_exit) from [<c009b5e0>] (__handle_domain_irq+0x58/0xb0)
[<c009b5e0>] (__handle_domain_irq) from [<c03a63c4>] (gic_handle_irq+0x48/0x98)
[<c03a63c4>] (gic_handle_irq) from [<c0009a10>] (__irq_svc+0x70/0x98)
...
This appears to be caused by mvneta_rx_hwbm() calling
dma_sync_single_range_for_cpu() with the wrong struct device pointer,
as the buffer manager device pointer is used to map and unmap the
buffer. Fix this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The changes to fix those are two invasive for backporting.
Just disable the feature in 4.20 and 5.0.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org> [4.20+]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect
[How]
change it to dce100_optimize_bandwidth
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The master clock is actually named masterck earlier in the driver. Having
"mck" in the parent list means that it can never be selected.
Fixes: 1eabdc2f9dd8 ("clk: at91: add at91sam9x5 PMCs driver")
Fixes: a2038077de9a ("clk: at91: add sama5d2 PMC driver")
Fixes: 084b696bb509 ("clk: at91: add sama5d4 pmc driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
nck() looks at the last id in an array and unfortunately,
at91sam9x35_periphck has a sentinel, hence the id is 0 and the calculated
number of peripheral clocks is 1 instead of a maximum of 31.
Fixes: 1eabdc2f9dd8 ("clk: at91: add at91sam9x5 PMCs driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some final pin control fixes (I hope) to round off the v5.0 pin
control development cycle.
Only driver fixes, one for stable:
- Meson8B fixup for the sdc pins
- Fix SDC tile position for Qualcomm QCS404"
* tag 'pinctrl-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: meson: meson8b: fix the sdxc_a data 1..3 pins
pinctrl: qcom: qcs404: Correct SDC tile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes for the v5.0 series:
- Per-instance irqchip on the MT7621
- Avoid direction setting using pin control on MMP2"
* tag 'gpio-v5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pxa: avoid attempting to set pin direction via pinctrl on MMP2
gpio: MT7621: use a per instance irq_chip structure
|
|
Pull MTD fixes from Boris Brezillon:
- Don't add a digit to MTD-backed nvmem device names
- Make sure powernv flash names are unique
* tag 'mtd/fixes-for-5.0-rc8' of git://git.infradead.org/linux-mtd:
mtd: powernv_flash: Fix device registration error
mtd: Use mtd->name when registering nvmem device
|
|
If we skipped all the connectors that were not part of a tile, we would
leave conn_seq=0 and conn_configured=0, convincing ourselves that we
had stagnated in our configuration attempts. Avoid this situation by
starting conn_seq=ALL_CONNECTORS, and repeating until we find no more
connectors to configure.
Fixes: 754a76591b12 ("drm/i915/fbdev: Stop repeating tile configuration on stagnation")
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190215123019.32283-1-chris@chris-wilson.co.uk
Cc: <stable@vger.kernel.org> # v3.19+
(cherry picked from commit d9b308b1f8a1acc0c3279f443d4fe0f9f663252e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
