aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-01-21be2net: ethtool self test reorganization.Sarveshwar Bandi
The ddr dma ethtool self test needs to be performed even when ETH_TEST_FL_OFFLINE is not set. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21vhost: fix TUN=m VHOST_NET=yMichael S. Tsirkin
drivers/built-in.o: In function `get_tun_socket': net.c:(.text+0x15436e): undefined reference to `tun_get_socket' If tun is a module, vhost must be a module, too. If tun is built-in or disabled, vhost can be built-in. Note: TUN || !TUN might look a bit strange until you realize that boolean logic rules do not apply for tristate variables. Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21phy: add RTBI mode for m88e1111Liu Yu-B13201
Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21ucc_geth: update the tbi-phy settingLiu Yu-B13201
Old method only set tbi-phy for eth0. Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Add 57765 phy ID and enable devices.Matt Carlson
This patch rounds out the 57765 asic rev support by adding the 57765 phy ID and entering the 57765 device IDs in the pci table. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Bypass power source switching for 57765Matt Carlson
The 57765 repurposes all the GPIOs normally used to switch power sources when configured as a NIC device. This patch changes the code to avoid touching the GPIOs for this asic rev. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Turn off the debug UART for 57765Matt Carlson
If the debug UART is left enabled, the LEDs will not work properly. This patch disables the debug UART. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Fix tx mailbox initializationMatt Carlson
If a device supports MSI-X interrupts, the driver assumes TSS will be available. This is not true for the 57765. This patch changes the code so that only the default tx mailbox is initialized if TSS is not available. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Supply a nicaddr for 57765 jumbo RCBMatt Carlson
The 57765 needs the driver to supply a nic address to the jumbo RCB, just like all other devices except the 5717. This patch changes the test to single out the 5717 rather than maintain a lengthy whitelist of asic revs. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Fix 5717 and 57765 memory selftestsMatt Carlson
Both the 5717 and the 57765 will fail 'ethtool -t' selftests at the memory selftest portion. The memory map for these two devices differs from the rest of the asic revs and each other. This patch adds a new memory map to use for memory selftests. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Abort phy init for 5717 serdes devicesMatt Carlson
The 5717 serdes devices have a different phy register layout than all other previous serdes devices. This patch aborts the phy init sequence in tg3_phy_reset() if the device is a 5717 serdes. It also aborts the tg3_phy_toggle_apd() operation. Most other operations in the MII_SERDES path are O.K. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Add 5717 serdes phy IDMatt Carlson
The serdes and copper phys of the 5717 asic rev have different phy IDs. This patch adds the serdes phy ID. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Improve internal resource allocationsMatt Carlson
The 5717 and the 57765 have more resources at their disposal internally. This patch tunes the driver to get better performance. The adjustments made here only apply to the 57765 and 5717 asic revs. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Enable PLL PD when CLKREQ disabled for 5717A0Matt Carlson
PCIe PLL power down cannot be used if CLKREQ is enabled because data corruption will occur. If CLKREQ is disabled though, enabling PCIE P1 PLL power-down saves some power. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-19Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 Conflicts: drivers/net/wireless/iwlwifi/iwl-core.h
2010-01-19ppp_generic.c severly whitespace damanged by ↵Lennart Sorensen
9c705260feea6ae329bc6b6d5f6d2ef0227eda0a I was just looking at ppp_generic, and noticed that it fairly recently (as in the last year) got rather mangled with many spaces turned into tabs in places they very much shouldn't have been. I tracked it down to commit 9c705260feea6ae329bc6b6d5f6d2ef0227eda0a (ppp: ppp_mp_explode() redesign). I am amazed if that patch passed the patch checking script. I have no idea what kind of weird editor setting did this, but it has to have been a weird editor setting or a very unfortunate search and replace gone wrong. I only found it trying to apply a patch I was playing with and wondering why it wouldn't apply. Then I found there were tabs in the middle of comments that used to be spaces. Well here is a patch that should fix it up as far as I can tell. Purely whitespace repair. No actual code changes. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-18drivers/net: Eliminate useless codeJulia Lawall
The variable qdev is initialized twice to the same (side effect-free) expression. Drop one initialization. A simplified version of the semantic match that finds this problem is: (http://coccinelle.lip6.fr/) // <smpl> @forall@ idexpression *x; identifier f!=ERR_PTR; @@ x = f(...) ... when != x ( x = f(...,<+...x...+>,...) | * x = f(...) ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-17bnx2: Save statistics during reset.Michael Chan
MTU changes, ring size changes, etc cause the chip to be reset and the statisctics flushed. To keep track of the accumulated statistics, we add code to save the whole statistics block before reset. We also modify the macros and statistics functions to return the sum of the saved and current counters. Based on original patch by Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-17bnx2: Refine statistics code.Michael Chan
Refine the statistics macros by passing in just the name of the counter field. This makes it a lot easier and cleaner to add counters saved before the last reset in the next patch. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-17net: spread __net_init, __net_exitAlexey Dobriyan
__net_init/__net_exit are apparently not going away, so use them to full extent. In some cases __net_init was removed, because it was called from __net_exit code. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16NET: Add Qlogic ethernet driver for CNA devicesAmit Kumar Salecha
o Separate Ethernet driver for Qlogic CNA devices Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlcnic: Qlogic ethernet driver for CNA devicesAmit Kumar Salecha
o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16macvlan: add GRO bit to features maskPatrick Mullaney
Allow macvlan devices to support GRO. Signed-off-by: Patrick Mullaney <pmullaney@novell.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add module param to force firmware core dump.Ron Mercer
Default setting is 'off', don't allow force firmware dump. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add xgmac reg blocks to firwmare dump.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add serdes reg blocks dump to firmware dump.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add alternate function's reg dump to fw dump.Ron Mercer
Get the 2nd (other) nic function register values. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add RAM dump to firmware dump.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add probe regs to firmware dump.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add basic firmware dump.Ron Mercer
Adding the infrstructure and basic data for the firmware core dump. The firmware coredump is turned OFF by default. There will be no memory allocations for data dumps to the log. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-16qlge: Add data for firmware dump.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-15b43: N-PHY: drop unused definition, uncomment needed callRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement TX power control coef setupRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add RX IQ calibrationi for rev < 3Rafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add huge calculating TX IQ LORafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement calculating IQ gain paramsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: update TX calibration ladderRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add RX radio cores calibrationRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add TX LP FBW (TX filter 40 related)Rafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement getting TX gainsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement calculating RX IQ compRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement RX IQ estimationRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement restoring general configurationRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>a Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement workaround for TX IQRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement RX IQ coeffsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add function than forces (not) staying in carrier searchRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add RSSI calibration restoreRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>` Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: implement PA overriding (RF control related)Rafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: RSSI calibration for rev < 3Rafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-15b43: N-PHY: add RSSI polling and setting 2055 (radio) VCMRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-28 14:49:54 +0000