Age | Commit message (Collapse) | Author |
|
Christian Brauner reported that if you use the TIOCGPTPEER ioctl() to
get a slave pty file descriptor, the resulting file descriptor doesn't
look right in /proc/<pid>/fd/<fd>. In particular, he wanted to use
readlink() on /proc/self/fd/<fd> to get the pathname of the slave pty
(basically implementing "ptsname{_r}()").
The reason for that was that we had generated the wrong 'struct path'
when we create the pty in ptmx_open().
In particular, the dentry was correct, but the vfsmount pointed to the
mount of the ptmx node. That _can_ be correct - in case you use
"/dev/pts/ptmx" to open the master - but usually is not. The normal
case is to use /dev/ptmx, which then looks up the pts/ directory, and
then the vfsmount of the ptmx node is obviously the /dev directory, not
the /dev/pts/ directory.
We actually did have the right vfsmount available, but in the wrong
place (it gets looked up in 'devpts_acquire()' when we get a reference
to the pts filesystem), and so ptmx_open() used the wrong mnt pointer.
The end result of this confusion was that the pty worked fine, but when
if you did TIOCGPTPEER to get the slave side of the pty, end end result
would also work, but have that dodgy 'struct path'.
And then when doing "d_path()" on to get the pathname, the vfsmount
would not match the root of the pts directory, and d_path() would return
an empty pathname thinking that the entry had escaped a bind mount into
another mount.
This fixes the problem by making devpts_acquire() return the vfsmount
for the pts filesystem, allowing ptmx_open() to trivially just use the
right mount for the pts dentry, and create the proper 'struct path'.
Reported-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of minor fixes (st, ses) and some bigger driver fixes for
qla2xxx (crash triggered by fw dump) and ipr (lockdep problems with
mq)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ses: Fix wrong page error
scsi: ipr: Fix scsi-mq lockdep issue
scsi: st: fix blk_get_queue usage
scsi: qla2xxx: Fix system crash while triggering FW dump
|
|
Pull networking fixes from David Miller:
1) Fix TCP checksum offload handling in iwlwifi driver, from Emmanuel
Grumbach.
2) In ksz DSA tagging code, free SKB if skb_put_padto() fails. From
Vivien Didelot.
3) Fix two regressions with bonding on wireless, from Andreas Born.
4) Fix build when busypoll is disabled, from Daniel Borkmann.
5) Fix copy_linear_skb() wrt. SO_PEEK_OFF, from Eric Dumazet.
6) Set SKB cached route properly in inet_rtm_getroute(), from Florian
Westphal.
7) Fix PCI-E relaxed ordering handling in cxgb4 driver, from Ding
Tianhong.
8) Fix module refcnt leak in ULP code, from Sabrina Dubroca.
9) Fix use of GFP_KERNEL in atomic contexts in AF_KEY code, from Eric
Dumazet.
10) Need to purge socket write queue in dccp_destroy_sock(), also from
Eric Dumazet.
11) Make bpf_trace_printk() work properly on 32-bit architectures, from
Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
bpf: fix bpf_trace_printk on 32 bit archs
PCI: fix oops when try to find Root Port for a PCI device
sfc: don't try and read ef10 data on non-ef10 NIC
net_sched: remove warning from qdisc_hash_add
net_sched/sfq: update hierarchical backlog when drop packet
net_sched: reset pointers to tcf blocks in classful qdiscs' destructors
ipv4: fix NULL dereference in free_fib_info_rcu()
net: Fix a typo in comment about sock flags.
ipv6: fix NULL dereference in ip6_route_dev_notify()
tcp: fix possible deadlock in TCP stack vs BPF filter
dccp: purge write queue in dccp_destroy_sock()
udp: fix linear skb reception with PEEK_OFF
ipv6: release rt6->rt6i_idev properly during ifdown
af_key: do not use GFP_KERNEL in atomic contexts
tcp: ulp: avoid module refcnt leak in tcp_set_ulp
net/cxgb4vf: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
net/cxgb4: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
PCI: Disable Relaxed Ordering Attributes for AMD A1100
PCI: Disable Relaxed Ordering for some Intel processors
PCI: Disable PCIe Relaxed Ordering if unsupported
...
|
|
Eric report a oops when booting the system after applying
the commit a99b646afa8a ("PCI: Disable PCIe Relaxed..."):
[ 4.241029] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
[ 4.247001] IP: pci_find_pcie_root_port+0x62/0x80
[ 4.253011] PGD 0
[ 4.253011] P4D 0
[ 4.253011]
[ 4.258013] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 4.262015] Modules linked in:
[ 4.265005] CPU: 31 PID: 1 Comm: swapper/0 Not tainted 4.13.0-dbx-DEV #316
[ 4.271002] Hardware name: Intel RML,PCH/Iota_QC_19, BIOS 2.40.0 06/22/2016
[ 4.279002] task: ffffa2ee38cfa040 task.stack: ffffa51ec0004000
[ 4.285001] RIP: 0010:pci_find_pcie_root_port+0x62/0x80
[ 4.290012] RSP: 0000:ffffa51ec0007ab8 EFLAGS: 00010246
[ 4.295003] RAX: 0000000000000000 RBX: ffffa2ee36bae000 RCX: 0000000000000006
[ 4.303002] RDX: 000000000000081c RSI: ffffa2ee38cfa8c8 RDI: ffffa2ee36bae000
[ 4.310013] RBP: ffffa51ec0007b58 R08: 0000000000000001 R09: 0000000000000000
[ 4.317001] R10: 0000000000000000 R11: 0000000000000000 R12: ffffa51ec0007ad0
[ 4.324005] R13: ffffa2ee36bae098 R14: 0000000000000002 R15: ffffa2ee37204818
[ 4.331002] FS: 0000000000000000(0000) GS:ffffa2ee3fcc0000(0000) knlGS:0000000000000000
[ 4.339002] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4.345001] CR2: 0000000000000050 CR3: 000000401000f000 CR4: 00000000001406e0
[ 4.351002] Call Trace:
[ 4.354012] ? pci_configure_device+0x19f/0x570
[ 4.359002] ? pci_conf1_read+0xb8/0xf0
[ 4.363002] ? raw_pci_read+0x23/0x40
[ 4.366011] ? pci_read+0x2c/0x30
[ 4.370014] ? pci_read_config_word+0x67/0x70
[ 4.374012] pci_device_add+0x28/0x230
[ 4.378012] ? pci_vpd_f0_read+0x50/0x80
[ 4.382014] pci_scan_single_device+0x96/0xc0
[ 4.386012] pci_scan_slot+0x79/0xf0
[ 4.389001] pci_scan_child_bus+0x31/0x180
[ 4.394014] acpi_pci_root_create+0x1c6/0x240
[ 4.398013] pci_acpi_scan_root+0x15f/0x1b0
[ 4.402012] acpi_pci_root_add+0x2e6/0x400
[ 4.406012] ? acpi_evaluate_integer+0x37/0x60
[ 4.411002] acpi_bus_attach+0xdf/0x200
[ 4.415002] acpi_bus_attach+0x6a/0x200
[ 4.418014] acpi_bus_attach+0x6a/0x200
[ 4.422013] acpi_bus_scan+0x38/0x70
[ 4.426011] acpi_scan_init+0x10c/0x271
[ 4.429001] acpi_init+0x2fa/0x348
[ 4.433004] ? acpi_sleep_proc_init+0x2d/0x2d
[ 4.437001] do_one_initcall+0x43/0x169
[ 4.441001] kernel_init_freeable+0x1d0/0x258
[ 4.445003] ? rest_init+0xe0/0xe0
[ 4.449001] kernel_init+0xe/0x150
====================== cut here =============================
It looks like the pci_find_pcie_root_port() was trying to
find the Root Port for the PCI device which is the Root
Port already, it will return NULL and trigger the problem,
so check the highest_pcie_bridge to fix thie problem.
Fixes: a99b646afa8a ("PCI: Disable PCIe Relaxed Ordering if unsupported")
Fixes: c56d4450eb68 ("PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC stats command takes a port ID, which doesn't exist on
pre-ef10 NICs (5000- and 6000- series). This is extracted from the
NIC specific data; we misinterpret this as the ef10 data structure,
causing us to read potentially unallocated data. With a KASAN kernel
this can cause errors with:
BUG: KASAN: slab-out-of-bounds in efx_mcdi_mac_stats
Fixes: 0a2ab4d988d7 ("sfc: set the port-id when calling MC_CMD_MAC_STATS")
Reported-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4vf Ethernet driver now queries PCIe configuration space to
determine if it can send TLPs to it with the Relaxed Ordering
Attribute set, just like the pf did.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4 Ethernet driver now queries PCIe configuration space to determine
if it can send TLPs to it with the Relaxed Ordering Attribute set.
Remove the enable_pcie_relaxed_ordering() to avoid enable PCIe Capability
Device Control[Relaxed Ordering Enable] at probe routine, to make sure
the driver will not send the Relaxed Ordering TLPs to the Root Complex which
could not deal the Relaxed Ordering TLPs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Casey reported that the AMD ARM A1100 SoC has a bug in its PCIe
Root Port where Upstream Transaction Layer Packets with the Relaxed
Ordering Attribute clear are allowed to bypass earlier TLPs with
Relaxed Ordering set, it would cause Data Corruption, so we need
to disable Relaxed Ordering Attribute when Upstream TLPs to the
Root Port.
Reported-and-suggested-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the Intel spec section 3.9.1 said:
3.9.1 Optimizing PCIe Performance for Accesses Toward Coherent Memory
and Toward MMIO Regions (P2P)
In order to maximize performance for PCIe devices in the processors
listed in Table 3-6 below, the soft- ware should determine whether the
accesses are toward coherent memory (system memory) or toward MMIO
regions (P2P access to other devices). If the access is toward MMIO
region, then software can command HW to set the RO bit in the TLP
header, as this would allow hardware to achieve maximum throughput for
these types of accesses. For accesses toward coherent memory, software
can command HW to clear the RO bit in the TLP header (no RO), as this
would allow hardware to achieve maximum throughput for these types of
accesses.
Table 3-6. Intel Processor CPU RP Device IDs for Processors Optimizing
PCIe Performance
Processor CPU RP Device IDs
Intel Xeon processors based on 6F01H-6F0EH
Broadwell microarchitecture
Intel Xeon processors based on 2F01H-2F0EH
Haswell microarchitecture
It means some Intel processors has performance issue when use the Relaxed
Ordering Attribute, so disable Relaxed Ordering for these root port.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MD fixes from Shaohua Li:
"Fix several bugs:
- fix a rcu stall issue introduced in 4.12 (Neil Brown)
- fix two raid5 cache race conditions (Song Liu)"
* tag 'md/4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: not clear ->safemode for external metadata array
md/r5cache: fix io_unit handling in r5l_log_endio()
md/r5cache: call mddev_lock/unlock() in r5c_journal_mode_set
md: fix test in md_write_start()
md: always clear ->safemode when md_check_recovery gets the mddev lock.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix an error path bug in ixp4xx as well as a read overrun in
sha1-avx2"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/sha1 - Fix reads beyond the number of blocks passed
crypto: ixp4xx - Fix error handling path in 'aead_perform()'
|
|
The firmware feature check introduced for multi-scheduled scan turned out
to be failing for bcm4343{0,1,8} devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Fixes: 9fe929aaace6 ("brcmfmac: add firmware feature detection for gscan feature")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
bond_miimon_commit() handles the UP transition for each slave of a bond
in the case of MII. It is triggered 10 times per second for the default
MII Polling interval of 100ms. For device drivers that do not implement
__ethtool_get_link_ksettings() the call to bond_update_speed_duplex()
fails persistently while the MII status could remain UP. That is, in
this and other cases where the speed/duplex update keeps failing over a
longer period of time while the MII state is UP, a warning is printed
every MII polling interval.
To address these excessive warnings net_ratelimit() should be used.
Printing a warning once would not be sufficient since the call to
bond_update_speed_duplex() could recover to succeed and fail again
later. In that case there would be no new indication what went wrong.
Fixes: b5bf0f5b16b9c (bonding: correctly update link status during mii-commit phase)
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are three firmware core fixes for 4.13-rc5.
All three of these fix reported issues and have been floating around
for a few weeks. They have been in linux-next with no reported
problems"
* tag 'driver-core-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: avoid invalid fallback aborts by using killable wait
firmware: fix batched requests - send wake up on failure on direct lookups
firmware: fix batched requests - wake all waiters
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues"
* tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Do not enumerate more ports from DROM than the controller has
mei: exclude device from suspend direct complete optimization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/iio fixes from Greg KH:
"Here are some Staging and IIO driver fixes for 4.13-rc5.
Nothing major, just a number of small fixes for reported issues. All
of these have been in linux-next for a while now with no reported
issues. Full details are in the shortlog"
* tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: comedi_fops: do not call blocking ops when !TASK_RUNNING
iio: aspeed-adc: wait for initial sequence.
iio: accel: bmc150: Always restore device to normal mode after suspend-resume
staging:iio:resolver:ad2s1210 fix negative IIO_ANGL_VEL read
iio: adc: axp288: Fix the GPADC pin reading often wrongly returning 0
iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits
iio: accel: st_accel: add SPI-3wire support
iio: adc: Revert "axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"
iio: adc: sun4i-gpadc-iio: fix unbalanced irq enable/disable
iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
iio: light: tsl2563: use correct event code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add new ATEN device id
usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
USB: Check for dropped connection before switching to full speed
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
USB: serial: option: add D-Link DWM-222 device ID
usb: musb: fix tx fifo flush handling again
usb: core: unlink urbs from the tail of the endpoint's urb_list
usb-storage: fix deadlock involving host lock and scsi_done
uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
USB: hcd: Mark secondary HCD as dead if the primary one died
USB: serial: cp210x: add support for Qivicon USB ZigBee dongle
|
|
Pull another MTD fix from Brian Norris:
"An mtdblock regression occurred in -rc1 (all writes were broken!), in
the process of some block subsystem refactoring. Noticed and fixed
last week, but I'm a little slow on the uptake"
* tag 'for-linus-20170812' of git://git.infradead.org/linux-mtd:
mtd: blkdevs: Fix mtd block write failure
|
|
All the MTD block write requests are failing with
following error messages
mkfs.ext4 /dev/mtdblock0
print_req_error: I/O error, dev mtdblock0, sector 0
Buffer I/O error on dev mtdblock0, logical block 0,
lost async page write
The control is going to default case after block write request
because of missing return.
Fixes: commit 2a842acab109 ("block: introduce new block status code type")
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights include:
- Fix iscsi-target payload memory leak during
ISCSI_FLAG_TEXT_CONTINUE (Varun Prakash)
- Fix tcm_qla2xxx incorrect use of tcm_qla2xxx_free_cmd during ABORT
(Pascal de Bruijn + Himanshu Madhani + nab)
- Fix iscsi-target long-standing issue with parallel delete of a
single network portal across multiple target instances (Gary Guo +
nab)
- Fix target dynamic se_node GPF during uncached shutdown regression
(Justin Maggard + nab)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix node_acl demo-mode + uncached dynamic shutdown regression
iscsi-target: Fix iscsi_np reset hung task during parallel delete
qla2xxx: Fix incorrect tcm_qla2xxx_free_cmd use during TMR ABORT (v2)
cxgbit: fix sg_nents calculation
iscsi-target: fix invalid flags in text response
iscsi-target: fix memory leak in iscsit_setup_text_cmd()
cxgbit: add missing __kfree_skb()
tcmu: free old string on reconfig
tcmu: Fix possible to/from address overflow when doing the memcpy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some fixes for Xen:
- a fix for a regression introduced in 4.13 for a Xen HVM-guest
configured with KASLR
- a fix for a possible deadlock in the xenbus driver when booting the
system
- a fix for lost interrupts in Xen guests"
* tag 'for-linus-4.13b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: Fix interrupt lost during irq_disable and irq_enable
xen: avoid deadlock in xenbus
xen: fix hvm guest with kaslr enabled
xen: split up xen_hvm_init_shared_info()
x86: provide an init_mem_mapping hypervisor hook
|
|
->safemode should be triggered by mdadm for external metadaa array, otherwise
array's state confuses mdadm.
Fixes: 33182d15c6bf(md: always clear ->safemode when md_check_recovery gets the mddev lock.)
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
If mISDN_FsmNew() fails to allocate memory for jumpmatrix
then null pointer dereference will occur on any write to
jumpmatrix.
The patch adds check on successful allocation and
corresponding error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Flower app may receive a request to update the MTU of a representor
netdev upon receipt of a control message from the firmware. This requires
the RTNL lock which needs to be taken outside of the packet processing
path.
As a handling of this correctly seems a little to invasive for a fix simply
skip setting the MTU for now.
Relevant backtrace:
[ 1496.288489] BUG: scheduling while atomic: kworker/0:3/373/0x00000100
[ 1496.294911] dca syscopyarea sysfillrect sysimgblt fb_sys_fops ptp drm mxm_wmi ahci pps_core libahci i2c_algo_bit wmi [last unloaded: nfp]
[ 1496.294918] CPU: 0 PID: 373 Comm: kworker/0:3 Tainted: G OE 4.13.0-rc3+ #3
[ 1496.294919] Hardware name: Supermicro X10DRi/X10DRi, BIOS 2.0 12/28/2015
[ 1496.294923] Workqueue: events work_for_cpu_fn
[ 1496.294924] Call Trace:
[ 1496.294927] <IRQ>
[ 1496.294931] dump_stack+0x63/0x82
[ 1496.294935] __schedule_bug+0x54/0x70
[ 1496.294937] __schedule+0x62f/0x890
[ 1496.294941] ? intel_unmap_sg+0x90/0x90
[ 1496.294942] schedule+0x36/0x80
[ 1496.294943] schedule_preempt_disabled+0xe/0x10
[ 1496.294945] __mutex_lock.isra.2+0x445/0x4a0
[ 1496.294947] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294950] ? kfree+0x162/0x170
[ 1496.294952] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294953] ? iommu_should_identity_map+0x50/0xe0
[ 1496.294954] __mutex_lock_slowpath+0x13/0x20
[ 1496.294955] ? iommu_no_mapping+0x48/0xd0
[ 1496.294956] ? __mutex_lock_slowpath+0x13/0x20
[ 1496.294957] mutex_lock+0x2f/0x40
[ 1496.294960] rtnl_lock+0x15/0x20
[ 1496.294979] nfp_flower_cmsg_rx+0xc8/0x150 [nfp]
[ 1496.294986] nfp_ctrl_poll+0x286/0x350 [nfp]
[ 1496.294989] tasklet_action+0xf6/0x110
[ 1496.294992] __do_softirq+0xed/0x278
[ 1496.294993] irq_exit+0xb6/0xc0
[ 1496.294994] do_IRQ+0x4f/0xd0
[ 1496.294996] common_interrupt+0x89/0x89
Fixes: 948faa46c05b ("nfp: add support for control messages for flower app")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the function stmmac_mdio_register() is only used by
stmmac_dvr_probe() from stmmac_main.c, in order to register the MDIO bus
and probe information about the PHY. As this function is called before
calling register_netdev(), all messages logged from stmmac_mdio_register
are prefixed by "(unnamed net_device)". The goal of netdev_info or
netdev_err is to dump useful infos about a net_device, when this data
structure is partially initialized, there is no point for using these
functions.
This commit fixes the issue by replacing all netdev_*() by the
corresponding dev_*() function for logging. The last netdev_info is
replaced by phy_attached_info(), as a valid phydev can be used at this
point.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes: c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"A set of fixes that should go into this series. This contains:
- Fix from Bart for blk-mq requeue queue running, preventing a
continued loop of run/restart.
- Fix for a bio/blk-integrity issue, in two parts. One from
Christoph, fixing where verification happens, and one from Milan,
for a NULL profile.
- NVMe pull request, most of the changes being for nvme-fc, but also
a few trivial core/pci fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix directive command numd calculation
nvme: fix nvme reset command timeout handling
nvme-pci: fix CMB sysfs file removal in reset path
lpfc: support nvmet_fc defer_rcv callback
nvmet_fc: add defer_req callback for deferment of cmd buffer return
nvme: strip trailing 0-bytes in wwid_show
block: Make blk_mq_delay_kick_requeue_list() rerun the queue at a quiet time
bio-integrity: only verify integrity on the lowest stacked driver
bio-integrity: Fix regression if profile verify_fn is NULL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- fix lockdep splat when removing mmc_block module
- fix the logic for setting eMMC HS400ES signal voltage
MMC host:
- omap_hsmmc: add CMD23 capability to fix -EIO errors"
* tag 'mmc-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: fix lockdep splat when removing mmc_block module
mmc: mmc: correct the logic for setting HS400ES signal voltage
mmc: host: omap_hsmmc: Add CMD23 capability to omap_hsmmc driver
|
|
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- allow user to disable write combined mapping in efifb driver (Dave
Airlie)
- fix use after free bugs on driver removal in imxfb driver (Dan
Carpenter)
- fix unused variable warning in omapfb driver (Arnd Bergmann)
* tag 'fbdev-v4.13-rc5' of git://github.com/bzolnier/linux:
efifb: allow user to disable write combined mapping.
fbdev: omapfb: remove unused variable
video: fbdev: imxfb: use after free in imxfb_remove()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Fix a NULL-pointer dereference in arm_smmu_add_device"
* tag 'iommu-fixes-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix null-pointer dereference in arm_smmu_add_device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"All fixes for code that went in this cycle.
- a revert of an optimisation to the syscall exit path, which could
lead to an oops on either older machines or machines with > 1TB of
memory
- disable some deep idle states if the firmware configuration for
them fails
- re-enable HARD/SOFT lockup detectors in defconfigs after a Kconfig
change
- six fairly small patches fixing bugs in our new watchdog code
Thanks to: Gautham R Shenoy, Nicholas Piggin"
* tag 'powerpc-4.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/watchdog: add locking around init/exit functions
powerpc/watchdog: Fix marking of stuck CPUs
powerpc/watchdog: Fix final-check recovered case
powerpc/watchdog: Moderate touch_nmi_watchdog overhead
powerpc/watchdog: Improve watchdog lock primitive
powerpc: NMI IPI improve lock primitive
powerpc/configs: Re-enable HARD/SOFT lockup detectors
powerpc/powernv/idle: Disable LOSE_FULL_CONTEXT states when stop-api fails
Revert "powerpc/64: Avoid restore_math call if possible in syscall exit"
|
|
Commit c54451a "iommu/arm-smmu: Fix the error path in arm_smmu_add_device"
removed fwspec assignment in legacy_binding path as redundant which is
wrong. It needs to be updated after fwspec initialisation in
arm_smmu_register_legacy_master() as it is dereferenced later. Without
this there is a NULL-pointer dereference panic during boot on some hosts.
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Here is a device has xen-pirq-MSI interrupt. Dom0 might lost interrupt
during driver irq_disable/irq_enable. Here is the scenario,
1. irq_disable -> disable_dynirq -> mask_evtchn(irq channel)
2. dev interrupt raised by HW and Xen mark its evtchn as pending
3. irq_enable -> startup_pirq -> eoi_pirq ->
clear_evtchn(channel of irq) -> clear pending status
4. consume_one_event process the irq event without pending bit assert
which result in interrupt lost once
5. No HW interrupt raising anymore.
Now use enable_dynirq for enable_pirq of xen_pirq_chip to remove
eoi_pirq when irq_enable.
Signed-off-by: Liu Shuo <shuo.a.liu@intel.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When starting the xenwatch thread a theoretical deadlock situation is
possible:
xs_init() contains:
task = kthread_run(xenwatch_thread, NULL, "xenwatch");
if (IS_ERR(task))
return PTR_ERR(task);
xenwatch_pid = task->pid;
And xenwatch_thread() does:
mutex_lock(&xenwatch_mutex);
...
event->handle->callback();
...
mutex_unlock(&xenwatch_mutex);
The callback could call unregister_xenbus_watch() which does:
...
if (current->pid != xenwatch_pid)
mutex_lock(&xenwatch_mutex);
...
In case a watch is firing before xenwatch_pid could be set and the
callback of that watch unregisters a watch, then a self-deadlock would
occur.
Avoid this by setting xenwatch_pid in xenwatch_thread().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Pull NVMe fixes from Christoph:
"A few more small fixes - the fc/lpfc update is the biggest by far."
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too earth shattering here, it just seems like lots of little
things all over the place.
msm has probably the larger amount of changes, but they all seem fine,
otherwise, some rockchip, i915, etnaviv and exynos fixes, along with
one nouveau regression fix for some older GPUs"
* tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/nouveau/disp/nv04: avoid creation of output paths
drm: make DRM_STM default n
drm/exynos: forbid creating framebuffers from too small GEM buffers
drm/etnaviv: Fix off-by-one error in reloc checking
drm/i915: fix backlight invert for non-zero minimum brightness
drm/i915/shrinker: Wrap need_resched() inside preempt-disable
drm/i915/perf: fix flex eu registers programming
drm/i915: Fix out-of-bounds array access in bdw_load_gamma_lut
drm/i915/gvt: Change the max length of mmio_reg_rw from 4 to 8
drm/i915/gvt: Initialize MMIO Block with HW state
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
drm/i915/gvt: clean workload queue if error happened
drm/i915/gvt: change resetting to resetting_eng
drm/msm: gpu: don't abuse dma_alloc for non-DMA allocations
drm/msm: gpu: call qcom_mdt interfaces only for ARCH_QCOM
drm/msm/adreno: Prevent unclocked access when retrieving timestamps
drm/msm: Remove __user from __u64 data types
...
|
|
Merge misc fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
userfaultfd: replace ENOSPC with ESRCH in case mm has gone during copy/zeropage
zram: rework copy of compressor name in comp_algorithm_store()
rmap: do not call mmu_notifier_invalidate_page() under ptl
mm: fix list corruptions on shmem shrinklist
mm/balloon_compaction.c: don't zero ballooned pages
MAINTAINERS: copy virtio on balloon_compaction.c
mm: fix KSM data corruption
mm: fix MADV_[FREE|DONTNEED] TLB flush miss problem
mm: make tlb_flush_pending global
mm: refactor TLB gathering API
Revert "mm: numa: defer TLB flush for THP migration as long as possible"
mm: migrate: fix barriers around tlb_flush_pending
mm: migrate: prevent racy access to tlb_flush_pending
fault-inject: fix wrong should_fail() decision in task context
test_kmod: fix small memory leak on filesystem tests
test_kmod: fix the lock in register_test_dev_kmod()
test_kmod: fix bug which allows negative values on two config options
test_kmod: fix spelling mistake: "EMTPY" -> "EMPTY"
userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
mm: ratelimit PFNs busy info message
...
|
|
comp_algorithm_store() passes the size of the source buffer to strlcpy()
instead of the destination buffer size. Make it explicit that the two
buffers have the same size and use strcpy() instead of strlcpy(). The
latter can be done safely since the function ensures that the string in
the source buffer is terminated.
Link: http://lkml.kernel.org/r/20170803163350.45245-1-mka@chromium.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Work around Renesas uPD72020x 32-bit DMA issue"
* tag 'pci-v4.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue
PCI: Add pci_reset_function_locked()
|
|
Some Alpine Ridge LP DROMs (there might be others) erroneusly list more
ports than the controller actually has. Most probably because DROM of
the full Dual/Single port Thunderbolt controller was reused for LP
version. The current DROM parser does not check the upper bound thus it
leads to crash when sw->ports[] is accessed over bounds:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002ec
IP: tb_drom_read+0x383/0x890 [thunderbolt]
PGD 0
P4D 0
Oops: 0000 [#1] SMP
CPU: 3 PID: 12248 Comm: systemd-udevd Not tainted 4.13.0-rc1-next-20170719 #1
Hardware name: LENOVO 20HF000YGE/20HF000YGE, BIOS N1WET32W (1.11 ) 05/23/2017
task: ffff8a293e4bcd80 task.stack: ffffa698027a8000
RIP: 0010:tb_drom_read+0x383/0x890 [thunderbolt]
RSP: 0018:ffffa698027ab990 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8a2940af7800 RCX: 0000000000000000
RDX: ffff8a2940ebb400 RSI: 0000000000000000 RDI: ffffa698027ab9a0
RBP: ffffa698027ab9d0 R08: 0000000000000001 R09: 0000000000000002
R10: ffff8a2940ebb5b0 R11: 0000000000000000 R12: ffff8a293bfa968c
R13: 000000000000002c R14: 0000000000000056 R15: 0000000000000056
FS: 00007f0a945a38c0(0000) GS:ffff8a2961580000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000002ec CR3: 000000043e785000 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
tb_switch_add+0x9d/0x730 [thunderbolt]
? tb_switch_alloc+0x3cd/0x4d0 [thunderbolt]
icm_start+0x5a/0xa0 [thunderbolt]
tb_domain_add+0xc3/0xf0 [thunderbolt]
nhi_probe+0x19e/0x310 [thunderbolt]
local_pci_probe+0x42/0xa0
pci_device_probe+0x18d/0x1a0
driver_probe_device+0x2ff/0x450
__driver_attach+0xa4/0xe0
? driver_probe_device+0x450/0x450
bus_for_each_dev+0x6e/0xb0
driver_attach+0x1e/0x20
bus_add_driver+0x1d0/0x270
? 0xffffffffc0bbb000
driver_register+0x60/0xe0
? 0xffffffffc0bbb000
__pci_register_driver+0x4c/0x50
nhi_init+0x28/0x1000 [thunderbolt]
do_one_initcall+0x50/0x190
? __vunmap+0x81/0xb0
? _cond_resched+0x1a/0x50
? kmem_cache_alloc_trace+0x15f/0x1c0
? do_init_module+0x27/0x1e9
do_init_module+0x5f/0x1e9
load_module+0x24e7/0x2a60
? vfs_read+0x115/0x130
SYSC_finit_module+0xfc/0x120
? SYSC_finit_module+0xfc/0x120
SyS_finit_module+0xe/0x10
do_syscall_64+0x67/0x170
entry_SYSCALL64_slow_path+0x25/0x25
Fix this by making sure we only enumerate DROM port entries the hardware
actually has.
Reported-by: Christian Kellner <ckellner@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Christian Kellner <ckellner@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MEI device performs link reset during system suspend sequence.
The link reset cannot be performed while device is in
runtime suspend state. The resume sequence is bypassed with
suspend direct complete optimization,so the optimization should be
disabled for mei devices.
Fixes:
[ 192.940537] Restarting tasks ...
[ 192.940610] PGI is not set
[ 192.940619] ------------[ cut here ]------------ [ 192.940623]
WARNING: CPU: 0
me.c:653 mei_me_pg_exit_sync+0x351/0x360 [ 192.940624] Modules
linked
in:
[ 192.940627] CPU: 0 PID: 1661 Comm: kworker/0:3 Not tainted
4.13.0-rc2+
#2 [ 192.940628] Hardware name: Dell Inc. XPS 13 9343/0TM99H, BIOS
A11
12/08/2016 [ 192.940630] Workqueue: pm pm_runtime_work <snip> [
192.940642] Call Trace:
[ 192.940646] ? pci_pme_active+0x1de/0x1f0 [ 192.940649] ?
pci_restore_standard_config+0x50/0x50
[ 192.940651] ? kfree+0x172/0x190
[ 192.940653] ? kfree+0x172/0x190
[ 192.940655] ? pci_restore_standard_config+0x50/0x50
[ 192.940663] mei_me_pm_runtime_resume+0x3f/0xc0
[ 192.940665] pci_pm_runtime_resume+0x7a/0xa0 [ 192.940667]
__rpm_callback+0xb9/0x1e0 [ 192.940668] ?
preempt_count_add+0x6d/0xc0 [ 192.940670] rpm_callback+0x24/0x90 [
192.940672] ? pci_restore_standard_config+0x50/0x50
[ 192.940674] rpm_resume+0x4e8/0x800 [ 192.940676]
pm_runtime_work+0x55/0xb0 [ 192.940678]
process_one_work+0x184/0x3e0 [ 192.940680]
worker_thread+0x4d/0x3a0 [ 192.940681] ?
preempt_count_sub+0x9b/0x100 [ 192.940683]
kthread+0x122/0x140 [ 192.940684] ? process_one_work+0x3e0/0x3e0 [
192.940685] ? __kthread_create_on_node+0x1a0/0x1a0
[ 192.940688] ret_from_fork+0x27/0x40 [ 192.940690] Code: 96 3a
9e ff 48 8b 7d 98 e8 cd 21 58 00 83 bb bc 01 00 00
04 0f 85 40 fe ff ff e9 41 fe ff ff 48 c7 c7 5f 04 99 96 e8 93 6b 9f
ff <0f> ff e9 5d fd ff ff e8 33 fe 99 ff 0f 1f 00 0f 1f 44 00 00 55
[ 192.940719] ---[ end trace
a86955597774ead8 ]--- [ 192.942540] done.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion
is interrupted") added via 4.0 added support to abort the fallback mechanism
when a signal was detected and wait_for_completion_interruptible() returned
-ERESTARTSYS -- for instance when a user hits CTRL-C. The abort was overly
*too* effective.
When a child process terminates (successful or not) the signal SIGCHLD can
be sent to the parent process which ran the child in the background and
later triggered a sync request for firmware through a sysfs interface which
relies on the fallback mechanism. This signal in turn can be recieved by the
interruptible wait we constructed on firmware_class and detects it as an
abort *before* userspace could get a chance to write the firmware. Upon
failure -EAGAIN is returned, so userspace is also kept in the dark about
exactly what happened.
We can reproduce the issue with the fw_fallback.sh selftest:
Before this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: error - sync firmware request cancelled due to SIGCHLD
After this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: SIGCHLD on sync ignored as expected
Fix this by making the wait killable -- only killable by SIGKILL (kill -9).
We loose the ability to allow userspace to cancel a write with CTRL-C
(SIGINT), however its been decided the compromise to require SIGKILL is
worth the gains.
Chances of this issue occuring are low due to the number of drivers upstream
exclusively relying on the fallback mechanism for firmware (2 drivers),
however this is observed in the field with custom drivers with sysfs
triggers to load firmware. Only distributions relying on the fallback
mechanism are impacted as well. An example reported issue was on Android,
as follows:
1) Android init (pid=1) fork()s (say pid=42) [this child process is totally
unrelated to firmware loading, it could be sleep 2; for all we care ]
2) Android init (pid=1) does a write() on a (driver custom) sysfs file which
ends up calling request_firmware() kernel side
3) The firmware loading fallback mechanism is used, the request is sent to
userspace and pid 1 waits in the kernel on wait_*
4) before firmware loading completes pid 42 dies (for any reason, even
normal termination)
5) Kernel delivers SIGCHLD to pid=1 to tell it a child has died, which
causes -ERESTARTSYS to be returned from wait_*
6) The kernel's wait aborts and return -EAGAIN for the
request_firmware() caller.
Cc: stable <stable@vger.kernel.org> # 4.0
Fixes: 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion is interrupted")
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix batched requests from waiting forever on failure.
The firmware API batched requests feature has been broken since the API call
request_firmware_direct() was introduced on commit bba3a87e982ad ("firmware:
Introduce request_firmware_direct()"), added on v3.14 *iff* the firmware
being requested was not present in *certain kernel builds* [0].
When no firmware is found the worker which goes on to finish never informs
waiters queued up of this, so any batched request will stall in what seems
to be forever (MAX_SCHEDULE_TIMEOUT). Sadly, a reboot will also stall, as
the reboot notifier was only designed to kill custom fallback workers. The
issue seems to the user as a type of soft lockup, what *actually* happens
underneath the hood is a wait call which never completes as we failed to
issue a completion on error.
For device drivers with optional firmware schemes (ie, Intel iwlwifi, or
Netronome -- even though it uses request_firmware() and not
request_firmware_direct()), this could mean that when you boot a system with
multiple cards the firmware will seem to never load on the system, or that
the card is just not responsive even the driver initialization. Due to
differences in scheduling possible this should not always trigger --
one would need to to ensure that multiple requests are in place at the
right time for this to work, also release_firmware() must not be called
prior to any other incoming request. The complexity may not be worth
supporting batched requests in the future given the wait mechanism is
only used also for the fallback mechanism. We'll keep it for now and
just fix it.
Its reported that at least with the Intel WiFi cards on one system this
issue was creeping up 50% of the boots [0].
Before this commit batched requests testing revealed:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
Ater this commit batched testing results:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
[0] https://bugzilla.kernel.org/show_bug.cgi?id=195477
Cc: stable <stable@vger.kernel.org> # v3.14
Fixes: bba3a87e982ad ("firmware: Introduce request_firmware_direct()"
Reported-by: Nicolas <nbroeking@me.com>
Reported-by: John Ewalt <jewalt@lgsinnovations.com>
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The firmware cache mechanism serves two purposes, the secondary purpose is
not well documented nor understood. This fixes a regression with the
secondary purpose of the firmware cache mechanism: batched requests on
successful lookups. Without this fix *any* time a batched request is
triggered, secondary requests for which the batched request mechanism
was designed for will seem to last forver and seem to never return.
This issue is present for all kernel builds possible, and a hard reset
is required.
The firmware cache is used for:
1) Addressing races with file lookups during the suspend/resume cycle
by keeping firmware in memory during the suspend/resume cycle
2) Batched requests for the same file rely only on work from the first file
lookup, which keeps the firmware in memory until the last
release_firmware() is called
Batched requests *only* take effect if secondary requests come in prior to
the first user calling release_firmware(). The devres name used for the
internal firmware cache is used as a hint other pending requests are
ongoing, the firmware buffer data is kept in memory until the last user of
the buffer calls release_firmware(), therefore serializing requests and
delaying the release until all requests are done.
Batched requests wait for a wakup or signal so we can rely on the first file
fetch to write to the pending secondary requests. Commit 5b029624948d
("firmware: do not use fw_lock for fw_state protection") ported the firmware
API to use swait, and in doing so failed to convert complete_all() to
swake_up_all() -- it used swake_up(), loosing the ability for *some* batched
requests to take effect.
We *could* fix this by just using swake_up_all() *but* swait is now known
to be very special use case, so its best to just move away from it. So we
just go back to using completions as before commit 5b029624948d ("firmware:
do not use fw_lock for fw_state protection") given this was using
complete_all().
Without this fix it has been reported plugging in two Intel 6260 Wifi cards
on a system will end up enumerating the two devices only 50% of the time
[0]. The ported swake_up() should have actually handled the case with two
devices, however, *if more than two cards are used* the swake_up() would
not have sufficed. This change is only part of the required fixes for
batched requests. Another fix is provided in the next patch.
This particular change should fix the cases where more than three requests
with the same firmware name is used, otherwise batched requests will wait
for MAX_SCHEDULE_TIMEOUT and just timeout eventually.
Below is a summary of tests triggering batched requests on different
kernel builds.
Before this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
After this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
[0] https://bugzilla.kernel.org/show_bug.cgi?id=195477
CC: <stable@vger.kernel.org> [4.10+]
Cc: Ming Lei <ming.lei@redhat.com>
Fixes: 5b029624948d ("firmware: do not use fw_lock for fw_state protection")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: stable <stable@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.
The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.
Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure. This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.
The logic for doing this is careful to check that the device is still
connected. But this check is inadequate if the device disconnects and
reconnects before the check is done. The symptom is that a device
works, but much more slowly than it is capable of operating.
The situation was made worse recently by commit 22547c4cc4fe ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.
This patch makes the check more robust. If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|