| Age | Commit message (Collapse) | Author |
|---|
|
All uses of MTD_MAX_{OOBFREE,ECCPOS}_ENTRIES_LARGE have been removed as
commit ef5eeea6e911 ("mtd: nand: brcm: switch to mtd_ooblayout_ops") and
commit aab616e31d1c ("mtd: kill the nand_ecclayout struct") replaced
struct nand_ecclayout by the new mtd_ooblayout_ops interface. Remove
these two macros therefore.
Reported-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210830083356.31702-1-gongruiqi1@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
|
|
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
|
|
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
|
|
Make use of spi-mem poll status APIs to let advanced controllers
optimize wait operations.
This should also fix the high CPU usage for system that don't have
a dedicated STATUS poll block logic.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210518162754.15940-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
|
|
The struct gpio_desc is declared in the middle of the rawnand.h header,
right before the first function using it (nand_gpio_waitrdy). Before
adding a new function and to make it clear: move the declaration to the
top of the file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-2-miquel.raynal@bootlin.com
|
|
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
|
|
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
|
|
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
|
|
When parsing the ONFI parameter page, save the available NV-DDR timing
modes in the core's dynamic ONFI structure. Once available to the rest
of the core out of the ONFI driver, these values will then be used to
derive the best timing mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-10-miquel.raynal@bootlin.com
|
|
Create the relevant ONFI NV-DDR timings structure and fill it with
default values from the ONFI specification.
Add the relevant structure entries and helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-9-miquel.raynal@bootlin.com
|
|
Both src_sync_timing_mode and src_ssync_features entries of the ONFI
parameter page have been updated and now are named nvddr_timing_modes,
nvddr2_timing_modes and nvddr_nvddr2_features, which is much more
understandable for someone which do not know the history of the ONFI
specification. Update the relevant structure with regard to these
changes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-8-miquel.raynal@bootlin.com
|
|
In particular, first ONFI specifications referred to SDR modes as
asynchronous modes, which is not the term we usually have in mind. The
spec has then been updated, so do the same here in the NAND subsystem to
avoid any possible confusion.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-7-miquel.raynal@bootlin.com
|
|
The current link to the ONFI specification is broken, the onfi.org
website now points to materials on Micron's website. Update the URL
accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-6-miquel.raynal@bootlin.com
|
|
Update the onfi.h header to use the BIT() macro.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-5-miquel.raynal@bootlin.com
|
|
Name it nand_interface_is_sdr() which will make even more sense when
nand_interface_is_nvddr() will be introduced.
Use it when relevant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-2-miquel.raynal@bootlin.com
|
|
Flash OTP regions can already be read via user space. Some boards have
their serial number or MAC addresses stored in the OTP regions. Add
support for them being a (read-only) nvmem provider.
The API to read the OTP data is already in place. It distinguishes
between factory and user OTP, thus there are up to two different
providers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210424110608.15748-6-michael@walle.cc
|
|
The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
|
|
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org
|
|
Use the new OTP ops to implement OTP access on Winbond flashes. Most
Winbond flashes provides up to four different OTP regions ("Security
Registers").
Winbond devices use a special opcode to read and write to the OTP
regions, just like the RDSFDP opcode. In fact, it seems that the
(undocumented) first OTP area of the newer flashes is the actual SFDP
table.
On a side note, Winbond devices also allow erasing the OTP regions as
long as the area isn't locked down.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-3-michael@walle.cc
|
|
linux/mtd/nand.h has been included at line 17.
So we remove the duplicate one at line 21.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323031737.259365-1-wanjiabing@vivo.com
|
|
This may sound like a contradiction but some SPI-NOR flashes really
support erasing their OTP region until it is finally locked. Having the
possibility to erase an OTP region might come in handy during
development.
The ioctl argument follows the OTPLOCK style.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210303201819.2752-1-michael@walle.cc
|
|
'linux/mtd/nand.h' included in 'rawnand.h' is duplicated.
It is also included in the 17th line.
Signed-off-by: Zhang Yunkai <zhang.yunkai@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210313105702.365878-1-zhang.yunkai@zte.com.cn
|
|
Get rid of central chrdev MTD lock, which prevents simultaneous operations
on completely independent physical MTD chips. Replace it with newly
introduced per-master mutex.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210217211845.43364-2-alexander.sverdlin@nokia.com
|
|
This patch introduces the module_mtd_blktrans macro which is a convenience
macro for mtd blktrans modules similar to module_platform_driver.
It is intended to be used by drivers which init/exit section does nothing
but register/unregister the mtd blktrans driver. By using this macro it is
possible to eliminate a few lines of boilerplate code per mtd blktrans
driver.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210213164600.409061-2-zhengdejin5@gmail.com
|
|
The software Hamming ECC engine stores the nsteps variable in its own
private structure while it is also exported as a public ECC field.
Let's get rid of the redundant private one and let's use the
nand_ecc_context structure when possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-10-miquel.raynal@bootlin.com
|
|
The software BCH ECC engine stores the nsteps variable in its own
private structure while it is also exported as a public ECC field.
Let's get rid of the redundant private one and let's use the
nand_ecc_context structure when possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-9-miquel.raynal@bootlin.com
|
|
This operation is very common and deserves a helper. It of course only
works after the ECC engine initialization.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-6-miquel.raynal@bootlin.com
|
|
This operation is very common and deserves a helper. It of course only
works after the ECC engine initialization.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-5-miquel.raynal@bootlin.com
|
|
This is an information that might be useful for specific uses, so
export it, which might avoid having to guess the number of steps when
necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-2-miquel.raynal@bootlin.com
|
|
The Global Block Unlock command has different names depending
on the manufacturer, but always the same command value: 0x98.
Macronix's MX25U12835F names it Gang Block Unlock, Winbond's
W25Q128FV names it Global Block Unlock and Microchip's
SST26VF064B names it Global Block Protection Unlock.
Used in the Individual Block Protection mode, which is mutually
exclusive with the Block Protection mode (BP0-3).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210121110546.382633-1-tudor.ambarus@microchip.com
|
|
SPI NOR core changes:
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
|
|
Some identifiers have different names between their prototypes
and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/9ed47a57d12c40e73a9b01612ee119d39baa6236.1603469755.git.mchehab+huawei@kernel.org
|
|
Add the logic in the NAND core to find the right ECC engine depending
on the NAND chip requirements and the user desires. Right now, the
choice may be made between (more will come):
* software Hamming
* software BCH
* on-die (SPI-NAND devices only)
Once the ECC engine has been found, the ECC engine must be
configured.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-2-miquel.raynal@bootlin.com
|
|
Before making use of the ECC engines, we must retrieve them. Add the
necessary boilerplate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-5-miquel.raynal@bootlin.com
|
|
Make use of the existing functions taken from the SPI-NAND core to
instantiate an on-die ECC engine specific to the SPI-NAND core. The
next step will be to tweak the core to use this object instead of
calling the helpers directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-4-miquel.raynal@bootlin.com
|
|
Before making use of the ECC engines, we must retrieve them. Add the
boilerplate for the ones already available: software engines (Hamming
and BCH).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-21-miquel.raynal@bootlin.com
|
|
Let's continue introducing the generic ECC engine abstraction in the
NAND subsystem by instantiating a second ECC engine: software
Hamming.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-20-miquel.raynal@bootlin.com
|
|
There is no reason to always embed the software Hamming ECC engine
implementation. By default it is (with raw NAND), but we can let the
user decide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-19-miquel.raynal@bootlin.com
|
|
Most of the includes are simply useless, drop them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-18-miquel.raynal@bootlin.com
|
|
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure. This means adding proper init/cleanup helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-17-miquel.raynal@bootlin.com
|
|
Prefix by ecc_sw_hamming_ the functions which should be internal only
but are exported for "raw" operations.
Prefix by nand_ecc_sw_hamming_ the other functions which will be used
in the context of the declaration of an Hamming proper ECC engine
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-16-miquel.raynal@bootlin.com
|
|
The include file pretends being the header for "ECC algorithm", while
it is just the header for the Hamming implementation. Make this clear
by rewording the sentence.
Do the same with the module description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-13-miquel.raynal@bootlin.com
|
|
Hamming ECC code might be later re-used by the SPI NAND layer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-12-miquel.raynal@bootlin.com
|
|
nand_ecc_ctrl embeds a private pointer which only has a meaning in the
sunxi driver. This structure will soon be deprecated, but as this
field is actually not needed, let's just drop it.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-11-miquel.raynal@bootlin.com
|
|
Let's continue introducing the generic ECC engine abstraction in the
NAND subsystem by instantiating a first ECC engine: the software
BCH one.
While at it, make a very tidy ecc_sw_bch_init() function and move all
the sanity checks and user input management in
nand_ecc_sw_bch_init_ctx(). This second helper will be called from the
raw RAND core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-10-miquel.raynal@bootlin.com
|
