| Age | Commit message (Collapse) | Author |
|---|
|
commit d2f19eec510424caa55ea949f016ddabe2d8173a upstream.
The "spi" parameters of spi_get_chipselect() and spi_get_csgpiod() can
be const.
Fixes: 303feb3cc06ac066 ("spi: Add APIs in spi core to set/get spi->chip_select and spi->cs_gpiod")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b112de79e7a1e9095a3b6ff22b639f39e39d7748.1678704562.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 303feb3cc06ac0665d0ee9c1414941200e60e8a3 ]
Supporting multi-cs in spi core and spi controller drivers would require
the chip_select & cs_gpiod members of struct spi_device to be an array.
But changing the type of these members to array would break the spi driver
functionality. To make the transition smoother introduced four new APIs to
get/set the spi->chip_select & spi->cs_gpiod and replaced all
spi->chip_select and spi->cs_gpiod references in spi core with the API
calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119185342.2093323-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fc70d643a2f6 ("spi: atmel: Fix clock issue when using devices with different polarities")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aea672d054a21782ed8450c75febb6ba3c208ca4 ]
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: ee4d79055aee ("iio: imu: adis16475: add spi_device_id table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bef4a48f4ef798c4feddf045d49e53c8a97d5e37 ]
A race condition exists where a synchronous (noqueue) transfer can be
active during a system suspend. This can cause a null pointer
dereference exception to occur when the system resumes.
Example order of events leading to the exception:
1. spi_sync() calls __spi_transfer_message_noqueue() which sets
ctlr->cur_msg
2. Spi transfer begins via spi_transfer_one_message()
3. System is suspended interrupting the transfer context
4. System is resumed
6. spi_controller_resume() calls spi_start_queue() which resets cur_msg
to NULL
7. Spi transfer context resumes and spi_finalize_current_message() is
called which dereferences cur_msg (which is now NULL)
Wait for synchronous transfers to complete before suspending by
acquiring the bus mutex and setting/checking a suspend flag.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20231107144743.v1.1.I7987f05f61901f567f7661763646cb7d7919b528@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description"
* tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: aspeed: Fix window offset of CE1
spi: qup: support using GPIO as chip select line
spi: intel: Fix the offset to get the 64K erase opcode
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
spi: mpc52xx: Replace NO_IRQ by 0
spi: spi-mem: Fix typo (of -> or)
spi: spi-gxp: fix typo in SPDX identifier line
spi: tegra210-quad: Fix combined sequence
|
|
In this instance, "or" makes more sense than "of", so I guess that "or"
was intended and "of" was a typo.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221008151459.1421406-1-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been
no work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in
the same message going to the same page
- Update the fsl_spi driver to use transfer_one() rather than a
custom transfer function
- Support for configuring transfer speeds with the AMD SPI controller
- Support for a second chip select and 64K erase on Intel SPI
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588"
* tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (73 commits)
spi: Ensure that sg_table won't be used after being freed
spi: spi-gxp: Use devm_platform_ioremap_resource()
spi: s3c64xx: Fix large transfers with DMA
spi: Split transfers larger than max size
spi: Fix cache corruption due to DMA/PIO overlap
spi: Save current RX and TX DMA devices
spi: mt65xx: Add dma max segment size declaration
spi: migrate mt7621 text bindings to YAML
spi: renesas,sh-msiof: Add r8a779g0 support
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
spi: s3c24xx: Switch to use devm_spi_alloc_master()
spi: xilinx: Switch to use devm_spi_alloc_master()
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
spi: aspeed: Remove redundant dev_err call
spi: spi-mpc52xx: switch to using gpiod API
...
|
|
Save the current RX and TX DMA devices to avoid having to duplicate the
logic to pick them, since we'll need access to them in some more
functions to fix a bug in the cache handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 5e0531f6b90a ("spi: Add capability to perform some transfer
with chipselect off") added a new flag but squeezed it into a wrong
group of struct spi_transfer members (note that SPI_NBITS_* are macros
for easier interpretation of the tx_nbits and rx_nbits bitfields).
Group cs_change and cs_off flags together and their doc strings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908130518.32186-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some components require a few clock cycles with chipselect off before
or/and after the data transfer done with CS on.
Typically IDT 801034 QUAD PCM CODEC datasheet states "Note *: CCLK
should have one cycle before CS goes low, and two cycles after
CS goes high".
The cycles "before" are implicitely provided by all previous activity
on the SPI bus. But the cycles "after" must be provided in order to
terminate the SPI transfer.
In order to use that kind of component, add a cs_off flag to
spi_transfer struct. When this flag is set, the transfer is performed
with chipselect off. This allows consummer to add a dummy transfer
at the end of the transfer list which is performed with chipselect
OFF, providing the required additional clock cycles.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/434165c46f06d802690208a11e7ea2500e8da4c7.1662558898.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi-mux driver is rather too clever and attempts to resubmit any
message that is submitted to it to the parent controller with some
adjusted callbacks. This does not play at all nicely with the fast
path which now sets flags on the message indicating that it's being
handled through the fast path, we see async messages flagged as being on
the fast path. Ideally the spi-mux code would duplicate the message but
that's rather invasive and a bit fragile in that it relies on the mux
knowing which fields in the message to copy. Instead teach the core
that there are controllers which can't cope with the fast path and have
the mux flag itself as being such a controller, ensuring that messages
going via the mux don't get partially handled via the fast path.
This will reduce the performance of any spi-mux connected device since
we'll now always use the thread for both the actual controller and the
mux controller instead of just the actual controller but given that we
were always hitting the slow path anyway it's hopefully not too much of
an additional cost and it allows us to keep the fast path.
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Casper Andersson <casper.casan@gmail.com>
Tested-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220901120732.49245-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Capitalize first word in comment where appropriate and add
parentheses to function names.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220629142519.3985486-3-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are only a few drivers that do not call
spi_finalize_current_message() in the context of transfer_one_message(),
and even for those cases the completion ctlr->cur_msg_completion is not
needed always. The calls to complete() and wait_for_completion() each
take a spin-lock, which is costly. This patch makes it possible to avoid
those calls in the big majority of cases, by introducing two flags that
with the help of ordering via barriers can avoid using the completion
safely. In case of a race with the context calling
spi_finalize_current_message(), the scheme errs on the safe side and takes
the completion.
The impact of this patch is worth the effort: On a i.MX8MM SoC, the time
the SPI bus is idle between two consecutive calls to spi_sync(), is
reduced from 19.6us to 16.8us... roughly 15%.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-12-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch introduces a completion that is completed in
spi_finalize_current_message() and waited for in
__spi_pump_transfer_message(). This way all manipulation of ctlr->cur_msg
is done with the io_mutex held and strictly ordered:
__spi_pump_transfer_message() will not return until
spi_finalize_current_message() is done using ctlr->cur_msg, and its
calling context is only touching ctlr->cur_msg after returning.
Due to this, we can safely drop the spin-locks around ctlr->cur_msg.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-11-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ctlr->idling flag is never checked now, so we don't need to set it
either.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-8-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The interaction with the controller message queue and its corresponding
auxiliary flags and variables requires the use of the queue_lock which is
costly. Since spi_sync will transfer the complete message anyway, and not
return until it is finished, there is no need to put the message into the
queue if the queue is empty. This can save a lot of overhead.
As an example of how significant this is, when using the MCP2518FD SPI CAN
controller on a i.MX8MM SoC, the time during which the interrupt line
stays active (during 3 relatively short spi_sync messages), is reduced
from 98us to 72us by this patch.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-3-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This enables the possibility to transfer a message that is not at the
current tip of the async message queue.
This is in preparation of the next patch(es) which enable spi_sync messages
to skip the queue altogether.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-2-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On 32 bit systems, the following kernel BUG is hit:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x18/0x24
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc1-00001-g6ae0aec8a366 #181
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
dump_backtrace from show_stack+0x20/0x24
r7:81024ffd r6:00000000 r5:81024ffd r4:60000013
show_stack from dump_stack_lvl+0x60/0x78
dump_stack_lvl from dump_stack+0x14/0x1c
r7:81024ffd r6:80f652de r5:80bec180 r4:819a2500
dump_stack from check_preemption_disabled+0xc8/0xf0
check_preemption_disabled from debug_smp_processor_id+0x18/0x24
r8:8119b7e0 r7:81205534 r6:819f5c00 r5:819f4c00 r4:c083d724
debug_smp_processor_id from __spi_sync+0x78/0x220
__spi_sync from spi_sync+0x34/0x4c
r10:bb7bf4e0 r9:c083d724 r8:00000007 r7:81a068c0 r6:822a83c0 r5:c083d724
r4:819f4c00
spi_sync from spi_mem_exec_op+0x338/0x370
r5:000000b4 r4:c083d910
spi_mem_exec_op from spi_nor_read_id+0x98/0xdc
r10:bb7bf4e0 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:82358040
r4:819f7c40
spi_nor_read_id from spi_nor_detect+0x38/0x114
r7:82358040 r6:00000000 r5:819f7c40 r4:819f7c40
spi_nor_detect from spi_nor_scan+0x11c/0xbec
r10:bb7bf4e0 r9:00000000 r8:00000000 r7:c083da4c r6:00000000 r5:00010101
r4:819f7c40
spi_nor_scan from spi_nor_probe+0x10c/0x2d0
r10:bb7bf4e0 r9:bb7bf4d0 r8:00000000 r7:819f4c00 r6:00000000 r5:00000000
r4:819f7c40
per-cpu access needs to be guarded against preemption.
Fixes: 6598b91b5ac3 ("spi: spi.c: Convert statistics to per-cpu u64_stats_t")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220609121334.2984808-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes these "make htmldocs" warnings:
include/linux/spi/spi.h:82: warning: Function parameter or member 'syncp' not described in 'spi_statistics'
include/linux/spi/spi.h:213: warning: Function parameter or member 'pcpu_statistics' not described in 'spi_device'
include/linux/spi/spi.h:676: warning: Function parameter or member 'pcpu_statistics' not described in 'spi_controller'
Fixes: 6598b91b5ac3 ("spi: spi.c: Convert statistics to per-cpu u64_stats_t")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Jander <david@protonic.nl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220608153309.2899565-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This change gives a dramatic performance improvement in the hot path,
since many costly spin_lock_irqsave() calls can be avoided.
On an i.MX8MM system with a MCP2518FD CAN controller connected via SPI,
the time the driver takes to handle interrupts, or in other words the time
the IRQ line of the CAN controller stays low is mainly dominated by the
time it takes to do 3 relatively short sync SPI transfers. The effect of
this patch is a reduction of this time from 136us down to only 98us.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220524091808.2269898-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-13-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
|
|
This fixes the corresponding warnings during building the docs.
Signed-off-by: Siddh Raman Pant <siddhpant.gh@gmail.com>
Link: https://lore.kernel.org/r/4e6187a4-d0f8-4750-e407-e09cc1c91789@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use a helper to set driver_override to the reduce amount of duplicated
code.
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
|
|
Commit d40f0b6f2e21 instroduced last_cs_enable to avoid setting
chipselect if it's not necessary, but it also introduces a bug. The
chipselect may not be set correctly on multi-device SPI busses. The
reason is that we can't judge the chipselect by bool last_cs_enable,
since chipselect may be modified after other devices were accessed.
So we should record the specific state of chipselect in case of
confusion.
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Link: https://lore.kernel.org/r/20220217141234.72737-1-yun.zhou@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All drivers using GPIOs as chip select have been rewritten to use
GPIO descriptors passing the ->use_gpio_descriptors flag. Retire
the code and fields used by the legacy GPIO API.
Do not drop the ->use_gpio_descriptors flag: it now only indicates
that we want to use GPIOs in addition to native chip selects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220210231954.807904-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Soon the SPI-NAND core will need a way to request a SPI controller to
enable ECC support for a given operation. This is because of the
pipelined integration of certain ECC engines, which are directly managed
by the SPI controller itself.
Introduce a spi_mem_op additional field for this purpose: ecc.
So far this field is left unset and checked to be false by all
the SPI controller drivers in their ->supports_op() hook, as they all
call spi_mem_default_supports_op().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-7-miquel.raynal@bootlin.com
|
|
Now that spi_mem_default_supports_op() has access to the static
controller capabilities (relating to memory operations), and now that
these capabilities have been filled by the relevant controllers, there
is no need for a specific helper checking only DTR operations, so let's
just kill spi_mem_dtr_supports_op() and simply use
spi_mem_default_supports_op() instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-6-miquel.raynal@bootlin.com
|
|
Create a spi_controller_mem_caps structure and put it within the
spi_controller structure close to the spi_controller_mem_ops
strucure. So far the only field in this structure is the support for dtr
operations, but soon we will add another parameter.
Also create a helper to parse the capabilities and check if the
requested capability has been set or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-2-miquel.raynal@bootlin.com
|
|
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
this series goal is to change the spi remove callback's return value to void.
After numerous patches nearly all drivers already return 0 unconditionally.
The four first patches in this series convert the remaining three drivers to
return 0, the final patch changes the remove prototype and converts all
implementers.
base-commit: 26291c54e111ff6ba87a164d85d4a4e134b7315c
|
|
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
This series enhances the helpers for ACPI resources to cope with
multiple resources and exports them for use in the x86 platform code's
multi-instantiate driver.
|
|
Some ACPI nodes may have more than one Spi Resource.
To be able to handle these case, its necessary to have
a way of counting these resources.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If a node contains more than one SPI resource it may be necessary to
use an index to select which one you want to allocate a spi device for.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This can then be used to find a spi resource inside an
ACPI node, and allocate a spi device.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This functions were previously made private since they
were not used. However, these functions will be needed
again.
Partial revert of commit da21fde0fdb3
("spi: Make several public functions private to spi.c")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This converts the PXA2xx SPI driver to use GPIO descriptors
exclusively to retrieve GPIO chip select lines.
The device tree and ACPI paths of the driver already use
descriptors, hence ->use_gpio_descriptors is already set and
this codepath is well tested.
Convert all the PXA boards providing chip select GPIOs as
platform data and drop the old GPIO chipselect handling in
favor of the core managing it exclusively.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220125005836.494807-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver has a bunch of custom oldstyle GPIO number-passing
fields and a custom set-up callback.
The good thing is: nothing in the kernel is using it.
Convert the driver to use GPIO descriptors with a SPI_MASTER_GPIO_SS
flag so that the local CS callback also get invoked as the hardware
needs this.
New users of this driver can provide GPIO descriptor tables like
the other converted drivers.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220119000914.192553-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit b42faeee718c ("spi: Add a PTP system timestamp
to the transfer structure") added an include of ptp_clock_kernel.h
to spi.h for struct ptp_system_timestamp but a forward declaration
is enough. Let's use that to limit the number of objects we have
to rebuild every time we touch networking headers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210904013140.2377609-1-kuba@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no user of the enable_loopback member in the struct pxa2xx_spi_chip.
Remote this legacy member completely.
The mentioned in the documentation the testing phase can be performed with
spidev_test tool.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211123192723.44537-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the last user of the custom ->cs_control() gone, we may get rid of
this legacy API completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211123192723.44537-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a single new driver, new features in others and some cleanups
all over the place.
Nothing really stands out and it is all relatively small.
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for
gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead
of accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom
interrupt code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force
one interrupt per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups"
* tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
virtio_gpio: drop packed attribute
gpio: virtio: Add IRQ support
gpio: realtek-otto: fix GPIO line IRQ offset
gpio: clean up Kconfig file
net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
gpio: mlxbf2: Introduce IRQ support
gpio: mc33880: Drop if with an always false condition
gpio: max730x: Make __max730x_remove() return void
gpio: aggregator: Wrap access to gpiochip_fwd.tmp[]
gpio: modepin: Add driver support for modepin GPIO controller
dt-bindings: gpio: zynqmp: Add binding documentation for modepin
firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
gpio: tps65218: drop unneeded MODULE_ALIAS
gpio: max77620: drop unneeded MODULE_ALIAS
gpio: xilinx: simplify getting .driver_data
gpio: tegra186: Support multiple interrupts per bank
gpio: tegra186: Force one interrupt per bank
gpio: uniphier: Use helper functions to get private data from IRQ data
gpio: uniphier: Use helper function to get IRQ hardware number
dt-bindings: gpio: add gpio-line-names to rockchip,gpio-bank.yaml
|
|
|
|
Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled. This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock. Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.
This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An spi or i2c remove callback is only called for devices that probed
successfully. In this case this implies that __max730x_probe() set a
non-NULL driver data. So the check ts == NULL is never true. With this
check dropped, __max730x_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
All these functions have no callers apart from drivers/spi/spi.c. So
drop their declarations in include/linux/spi/spi.h and don't export
them.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211007121415.2401638-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The last user is gone since commit
2962db71c703 ("staging/fbtft: Remove fbtft_device")
in 2019.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211007121415.2401638-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The functions in the platform data struct to initialize, cleanup and
apply custom filters are not in use by any mainline board.
Remove support for them to pave the road for more cleanups to come.
The enum was moved as it has no users outside of the driver code
itself.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210907200726.2034962-3-daniel@zonque.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
