| Age | Commit message (Collapse) | Author |
|---|
|
This commit adds support for PKTDMA in k3-udma glue driver. Use new
psil_endpoint_config struct to get static data for a given channel or a
flow during setup. Make sure that the RX flows being mapped to a RX
channel is within the range of flows that is been allocated to that RX
channel.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-21-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The DMAs in AM64 have built in rings compared to AM654/J721e/J7200 where a
separate and generic ringacc is used.
The ring SW interface is similar to ringacc with some major architectural
differences, like
They are part of the DMA (BCDMA or PKTDMA).
They are dual mode rings are modeled as pair of Rings objects which has
common configuration and memory buffer, but separate real-time control
register sets for each direction mem2dev (forward) and dev2mem (reverse).
The ringacc driver must be initialized for DMA rings use with
k3_ringacc_dmarings_init() as it is not an independent device as ringacc
is.
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-17-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In k3 architecture a DMA channel (in TR momde) can be triggered by global
events, origination from different modules.
The events for triggers can be sent from any module which is connected to
PSI-L fabric, but the event number to be sent is DMA channel specific, it
is only known after the channel itself is requested.
The router operation needs to be split up:
- route_allocate: configure the dma_spec for the DMA and store the
configuration which is needed for the router's input
- set_event: callback used by the DMA driver to set the event number for
the channel and enable the routing
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-16-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Additional fields needed for K3 PKTDMA to be able to handle the mapped
channels (channels are locked to handle specific threads) and flow ranges
for these mapped threads.
PKTDMA also introduces tflow for tx channels which can not be found in
K3 UDMA architecture.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-14-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If the DMA device supports per channel coherency configuration (a channel
can be configured to have coherent or not coherent view) then a single
device (the DMA controller's device) can not be used for dma_api for all
channels as channels can have different coherency.
Introduce custom_dma_mapping flag for the dma_chan and a new helper to get
the device pointer to be used for dma_api for the given channel.
Client drivers should be updated to be able to support per channel
coherency by:
- dma_map_single(chan->device->dev, ptr, size, DMA_TO_DEVICE);
+ struct device *dma_dev = dmaengine_get_dma_device(chan);
+
+ dma_map_single(dma_dev, ptr, size, DMA_TO_DEVICE);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-9-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Additional configuration for the DMA event router might be needed for a
channel which can not be done during device_alloc_chan_resources callback
since the router information is not yet present for the drivers.
If there is a need for additional configuration for the channel if DMA
router is in use, then the driver can implement the device_router_config
callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-8-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Glue layer users should use the device of the DMA for DMA mapping and
allocations as it is the DMA which accesses to descriptors and buffers,
not the clients
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-5-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
drivers: soc: TI SOC changes for 5.11
- ti_sci changes towards DMSS support
- Static warning fixes
- Kconfig update for Keystone ARM64 socs
- AM64X SOC family support
|
|
This controller provides DMAengine capabilities for a variety of peripheral
buses such as I2C, UART, and SPI. By using GPI dmaengine driver, bus
drivers can use a standardize interface that is protocol independent to
transfer data between memory and peripheral.
Link: https://lore.kernel.org/r/20201109085450.24843-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some complex dmaengine controllers have capability to program the
peripheral device, so pass on the peripheral configuration as part of
dma_slave_config
Link: https://lore.kernel.org/r/20201109085450.24843-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In RING mode the ringacc does not access the ring memory. In this access
mode the ringacc coherency does not have meaning.
If the ring is configured in RING mode, then the ringacc itself will not
access to the ring memory. Only the requester (user) of the ring is going
to read/write to the memory.
Extend the ring configuration parameters with a device pointer to be used
for DMA API when the ring is configured in RING mode.
Extending the ring configuration struct will allow per ring selection of
device to be used for allocation, thus allowing per ring coherency.
To avoid regression, fall back to use the ringacc dev in case the alloc_dev
is not provided.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The ringacc driver has been converted to use the new set_cfg function to
configure the ring, the old config ops can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The sysfw ring configuration message has been extended to include virtid
and asel value for the ring.
Add the ASEL_VALID to TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER as it is required
for DMA rings.
Instead of extending the current .config() ops - which would need same
patch change in the ringacc driver - add ti_sci_msg_rm_ring_cfg struct and
a new ops using it to configure the ring.
This will allow easy update path in case new members are added for the ring
configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The ring_get_cfg (0x1111 message) is not used and it is not supported by
sysfw for a long time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Sysfw added 'extended_ch_type' to the tx_ch_cfg_req message which should be
used when BCDMA block copy channels are configured:
extended_ch_type = 0 : the channel is split tx channel (tchan)
extended_ch_type = 1 : the channel is block copy channel (bchan)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Sysfw added support for a second range in the resource range API to be able
to describe complex allocations mainly for DMA channels.
Update the ti_sci part to consider the second range as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Use the ti_sci_resource_desc directly and update it's start and num members
directly instead of requiring individual parameters for them.
This will allow easy extension of the RM parameters without changing API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The system controller's resource manager have support for configuring the
TDTYPE of TCHAN_CFG register on j721e.
With this parameter the teardown completion can be controlled:
TDTYPE == 0: Return without waiting for peer to complete the teardown
TDTYPE == 1: Wait for peer to complete the teardown
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 453431a54934 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"Just a trivial fix for kernel-doc warnings"
* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlocks: Fix kernel-doc warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become 000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom
Pull random32 updates from Willy Tarreau:
"Make prandom_u32() less predictable.
This is the cleanup of the latest series of prandom_u32
experimentations consisting in using SipHash instead of Tausworthe to
produce the randoms used by the network stack.
The changes to the files were kept minimal, and the controversial
commit that used to take noise from the fast_pool (f227e3ec3b5c) was
reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
fed from various sources of activities (networking, scheduling) to
perturb the SipHash state using fast, non-trivially predictable data,
instead of keeping it fully deterministic. The goal is essentially to
make any occasional memory leakage or brute-force attempt useless.
The resulting code was verified to be very slightly faster on x86_64
than what is was with the controversial commit above, though this
remains barely above measurement noise. It was also tested on i386 and
arm, and build- tested only on arm64"
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
random32: add a selftest for the prandom32 code
random32: add noise from network and scheduling activity
random32: make prandom_u32() output unpredictable
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph
- rdma error handling fixes (Chao Leng)
- fc error handling and reconnect fixes (James Smart)
- fix the qid displace when tracing ioctl command (Keith Busch)
- don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
- fix MTDT for passthru (Logan Gunthorpe)
- blacklist Write Same on more devices (Kai-Heng Feng)
- fix an uninitialized work struct (zhenwei pi)"
- lightnvm out-of-bounds fix (Colin)
- SG allocation leak fix (Doug)
- rnbd fixes (Gioh, Guoqing, Jack)
- zone error translation fixes (Keith)
- kerneldoc markup fix (Mauro)
- zram lockdep fix (Peter)
- Kill unused io_context members (Yufen)
- NUMA memory allocation cleanup (Xianting)
- NBD config wakeup fix (Xiubo)
* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
block: blk-mq: fix a kernel-doc markup
nvme-fc: shorten reconnect delay if possible for FC
nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
nvme-fc: fix error loop in create_hw_io_queues
nvme-fc: fix io timeout to abort I/O
null_blk: use zone status for max active/open
nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
nvmet: cleanup nvmet_passthru_map_sg()
nvmet: limit passthru MTDS by BIO_MAX_PAGES
nvmet: fix uninitialized work for zero kato
nvme-pci: disable Write Zeroes on Sandisk Skyhawk
nvme: use queuedata for nvme_req_qid
nvme-rdma: fix crash due to incorrect cqe
nvme-rdma: fix crash when connect rejected
block: remove unused members for io_context
blk-mq: remove the calling of local_memory_node()
zram: Fix __zram_bvec_{read,write}() locking order
skd_main: remove unused including <linux/version.h>
sgl_alloc_order: fix memory leak
lightnvm: fix out-of-bounds write to array devices->info[]
...
|
|
Pull io_uring fixes from Jens Axboe:
- fsize was missed in previous unification of work flags
- Few fixes cleaning up the flags unification creds cases (Pavel)
- Fix NUMA affinities for completely unplugged/replugged node for io-wq
- Two fallout fixes from the set_fs changes. One local to io_uring, one
for the splice entry point that io_uring uses.
- Linked timeout fixes (Pavel)
- Removal of ->flush() ->files work-around that we don't need anymore
with referenced files (Pavel)
- Various cleanups (Pavel)
* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
splice: change exported internal do_splice() helper to take kernel offset
io_uring: make loop_rw_iter() use original user supplied pointers
io_uring: remove req cancel in ->flush()
io-wq: re-set NUMA node affinities if CPUs come online
io_uring: don't reuse linked_timeout
io_uring: unify fsize with def->work_flags
io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
io_uring: do poll's hash_node init in common code
io_uring: inline io_poll_task_handler()
io_uring: remove extra ->file check in poll prep
io_uring: make cached_cq_overflow non atomic_t
io_uring: inline io_fail_links()
io_uring: kill ref get/drop in personality init
io_uring: flags-based creds init in queue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff all over the place (the largest group here is
Christoph's stat cleanups)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: remove KSTAT_QUERY_FLAGS
fs: remove vfs_stat_set_lookup_flags
fs: move vfs_fstatat out of line
fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
fs: remove vfs_statx_fd
fs: omfs: use kmemdup() rather than kmalloc+memcpy
[PATCH] reduce boilerplate in fsid handling
fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
selftests: mount: add nosymfollow tests
Add a "nosymfollow" mount option.
|
|
Pull dma-mapping fixes from Christoph Hellwig:
- document the new dma_{alloc,free}_pages() API
- two fixups for the dma-mapping.h split
* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: document dma_{alloc,free}_pages
dma-mapping: move more functions to dma-map-ops.h
ARM/sa1111: add a missing include of dma-map-ops.h
|
|
With the removal of the interrupt perturbations in previous random32
change (random32: make prandom_u32() output unpredictable), the PRNG
has become 100% deterministic again. While SipHash is expected to be
way more robust against brute force than the previous Tausworthe LFSR,
there's still the risk that whoever has even one temporary access to
the PRNG's internal state is able to predict all subsequent draws till
the next reseed (roughly every minute). This may happen through a side
channel attack or any data leak.
This patch restores the spirit of commit f227e3ec3b5c ("random32: update
the net random state on interrupt and activity") in that it will perturb
the internal PRNG's statee using externally collected noise, except that
it will not pick that noise from the random pool's bits nor upon
interrupt, but will rather combine a few elements along the Tx path
that are collectively hard to predict, such as dev, skb and txq
pointers, packet length and jiffies values. These ones are combined
using a single round of SipHash into a single long variable that is
mixed with the net_rand_state upon each invocation.
The operation was inlined because it produces very small and efficient
code, typically 3 xor, 2 add and 2 rol. The performance was measured
to be the same (even very slightly better) than before the switch to
SipHash; on a 6-core 12-thread Core i7-8700k equipped with a 40G NIC
(i40e), the connection rate dropped from 556k/s to 555k/s while the
SYN cookie rate grew from 5.38 Mpps to 5.45 Mpps.
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
|
|
Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output. An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.
It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack. Oops.
This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key. (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.) Speed is prioritized over security;
attacks are rare, while performance is always wanted.
Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution. This patch replaces
it.
Reported-by: Amit Klein <aksecurity@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of f227e3ec3b5c; moved SIPROUND definitions
to prandom.h for later use; merged George's prandom_seed() proposal;
inlined siprand_u32(); replaced the net_rand_state[] array with 4
members to fix a build issue; cosmetic cleanups to make checkpatch
happy; fixed RANDOM32_SELFTEST build ]
Signed-off-by: Willy Tarreau <w@1wt.eu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
"Just a single patch set: the remainder of Christoph's work to remove
set_fs, including the RISC-V portion"
* tag 'riscv-for-linus-5.10-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove address space overrides using set_fs()
riscv: implement __get_kernel_nofault and __put_user_nofault
riscv: refactor __get_user and __put_user
riscv: use memcpy based uaccess for nommu again
asm-generic: make the set_fs implementation optional
asm-generic: add nommu implementations of __{get,put}_kernel_nofault
asm-generic: improve the nommu {get,put}_user handling
uaccess: provide a generic TASK_SIZE_MAX definition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"First of all, the adaptive voltage scaling (AVS) drivers go to new
platform-specific locations as planned (this part was reported to have
merge conflicts against the new arm-soc updates in linux-next).
In addition to that, there are some fixes (intel_idle, intel_pstate,
RAPL, acpi_cpufreq), the addition of on/off notifiers and idle state
accounting support to the generic power domains (genpd) code and some
janitorial changes all over.
Specifics:
- Move the AVS drivers to new platform-specific locations and get rid
of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra)"
* tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
PM: sleep: remove unreachable break
PM: AVS: Drop the avs directory and the corresponding Kconfig
PM: AVS: qcom-cpr: Move the driver to the qcom specific drivers
PM: runtime: Fix typo in pm_runtime_set_active() helper comment
PM: domains: Fix build error for genpd notifiers
powercap: Fix typo in Kconfig "Plance" -> "Plane"
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
PM: AVS: smartreflex Move driver to soc specific drivers
PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers
PM: domains: enable domain idle state accounting
PM: domains: Add curly braces to delimit comment + statement block
PM: domains: Add support for PM domain on/off notifiers for genpd
powercap/intel_rapl: enumerate Psys RAPL domain together with package RAPL domain
powercap/intel_rapl: Fix domain detection
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for ADC driven joysticks
- a new Zintix touchscreen driver
- enhancements to Intel SoC button array driver
- support for F3A "function" in Synaptics RMI4 driver
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: Add MAINTAINERS entry for SiS i2c touch input driver
Input: evdev - per-client waitgroups
Input: synaptics - enable InterTouch for ThinkPad T14 Gen 1
Input: synaptics - enable InterTouch for ThinkPad P1/X1E gen 2
Input: synaptics-rmi4 - support bootloader v8 in f34v7
Input: synaptics-rmi4 - add support for F3A
Input: synaptics-rmi4 - rename f30_data to gpio_data
Input: add zinitix touchscreen driver
dt-bindings: input/touchscreen: add bindings for zinitix
Input: joystick - add ADC attached joystick driver.
dt-bindings: input: Add docs for ADC driven joystick
Input: sun4i-ps2 - fix handling of platform_get_irq() error
Input: twl4030_keypad - fix handling of platform_get_irq() error
Input: omap4-keypad - fix handling of platform_get_irq() error
Input: ep93xx_keypad - fix handling of platform_get_irq() error
Input: stmfts - fix a & vs && typo
Input: imx6ul_tsc - unify open/close and PM paths
Input: imx6ul_tsc - clean up some errors in imx6ul_tsc_resume()
Input: elants_i2c - fix typo for an attribute to show calibration count
Input: elants_i2c - report resolution of ABS_MT_TOUCH_MAJOR by FW information.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late in
the 5.9 cycle started depending on a return code from a function
which changed with the 5.10 PR from the usb subsystem
Current release regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous release regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu() to
synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems; the
property is not populated correctly by the firmware, but firmware
configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is light
and only wants to schedule napi (and do so through a _irqoff()
variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it"
* tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
tcp: fix to update snd_wl1 in bulk receiver fast path
net: Properly typecast int values to set sk_max_pacing_rate
netfilter: nf_fwd_netdev: clear timestamp in forwarding path
ibmvnic: save changed mac address to adapter->mac_addr
selftests: mptcp: depends on built-in IPv6
Revert "virtio-net: ethtool configurable RXCSUM"
rtnetlink: fix data overflow in rtnl_calcit()
net: ethernet: mtk-star-emac: select REGMAP_MMIO
net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup
net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device
bpf, libbpf: Guard bpf inline asm from bpf_tail_call_static
bpf, selftests: Extend test_tc_redirect to use modified bpf_redirect_neigh()
bpf: Fix bpf_redirect_neigh helper api to support supplying nexthop
mptcp: depends on IPV6 but not as a module
sfc: move initialisation of efx->filter_sem to efx_init_struct()
mpls: load mpls_gso after mpls_iptunnel
net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN tunnels
net/sched: act_gate: Unlock ->tcfa_lock in tc_setup_flow_action()
net: dsa: bcm_sf2: make const array static, makes object smaller
mptcp: MPTCP_IPV6 should depend on IPV6 instead of selecting it
...
|
|
Pull clone/dedupe/remap code refactoring from Darrick Wong:
"Move the generic file range remap (aka reflink and dedupe) functions
out of mm/filemap.c and fs/read_write.c and into fs/remap_range.c to
reduce clutter in the first two files"
* tag 'vfs-5.10-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
vfs: move the generic write and copy checks out of mm
vfs: move the remap range helpers to remap_range.c
vfs: move generic_remap_checks out of mm
|
|
Pull KVM updates from Paolo Bonzini:
"For x86, there is a new alternative and (in the future) more scalable
implementation of extended page tables that does not need a reverse
map from guest physical addresses to host physical addresses.
For now it is disabled by default because it is still lacking a few of
the existing MMU's bells and whistles. However it is a very solid
piece of work and it is already available for people to hammer on it.
Other updates:
ARM:
- New page table code for both hypervisor and guest stage-2
- Introduction of a new EL2-private host context
- Allow EL2 to have its own private per-CPU variables
- Support of PMU event filtering
- Complete rework of the Spectre mitigation
PPC:
- Fix for running nested guests with in-kernel IRQ chip
- Fix race condition causing occasional host hard lockup
- Minor cleanups and bugfixes
x86:
- allow trapping unknown MSRs to userspace
- allow userspace to force #GP on specific MSRs
- INVPCID support on AMD
- nested AMD cleanup, on demand allocation of nested SVM state
- hide PV MSRs and hypercalls for features not enabled in CPUID
- new test for MSR_IA32_TSC writes from host and guest
- cleanups: MMU, CPUID, shared MSRs
- LAPIC latency optimizations ad bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (232 commits)
kvm: x86/mmu: NX largepage recovery for TDP MMU
kvm: x86/mmu: Don't clear write flooding count for direct roots
kvm: x86/mmu: Support MMIO in the TDP MMU
kvm: x86/mmu: Support write protection for nesting in tdp MMU
kvm: x86/mmu: Support disabling dirty logging for the tdp MMU
kvm: x86/mmu: Support dirty logging for the TDP MMU
kvm: x86/mmu: Support changed pte notifier in tdp MMU
kvm: x86/mmu: Add access tracking for tdp_mmu
kvm: x86/mmu: Support invalidate range MMU notifier for TDP MMU
kvm: x86/mmu: Allocate struct kvm_mmu_pages for all pages in TDP MMU
kvm: x86/mmu: Add TDP MMU PF handler
kvm: x86/mmu: Remove disallowed_hugepage_adjust shadow_walk_iterator arg
kvm: x86/mmu: Support zapping SPTEs in the TDP MMU
KVM: Cache as_id in kvm_memory_slot
kvm: x86/mmu: Add functions to handle changed TDP SPTEs
kvm: x86/mmu: Allocate and free TDP MMU roots
kvm: x86/mmu: Init / Uninit the TDP MMU
kvm: x86/mmu: Introduce tdp_iter
KVM: mmu: extract spte.h and spte.c
KVM: mmu: Separate updating a PTE from kvm_set_pte_rmapp
...
|
|
Pull virtio updates from Michael Tsirkin:
"vhost, vdpa, and virtio cleanups and fixes
A very quiet cycle, no new features"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
MAINTAINERS: add URL for virtio-mem
vhost_vdpa: remove unnecessary spin_lock in vhost_vring_call
vringh: fix __vringh_iov() when riov and wiov are different
vdpa/mlx5: Setup driver only if VIRTIO_CONFIG_S_DRIVER_OK
s390: virtio: PV needs VIRTIO I/O device protection
virtio: let arch advertise guest's memory access restrictions
vhost_vdpa: Fix duplicate included kernel.h
vhost: reduce stack usage in log_used
virtio-mem: Constify mem_id_table
virtio_input: Constify id_table
virtio-balloon: Constify id_table
vdpa/mlx5: Fix failure to bring link up
vdpa/mlx5: Make use of a specific 16 bit endianness API
|
|
Pull arch task_work cleanups from Jens Axboe:
"Two cleanups that don't fit other categories:
- Finally get the task_work_add() cleanup done properly, so we don't
have random 0/1/false/true/TWA_SIGNAL confusing use cases. Updates
all callers, and also fixes up the documentation for
task_work_add().
- While working on some TIF related changes for 5.11, this
TIF_NOTIFY_RESUME cleanup fell out of that. Remove some arch
duplication for how that is handled"
* tag 'arch-cleanup-2020-10-22' of git://git.kernel.dk/linux-block:
task_work: cleanup notification modes
tracehook: clear TIF_NOTIFY_RESUME in tracehook_notify_resume()
|
|
* pm-core:
PM: runtime: Fix typo in pm_runtime_set_active() helper comment
* pm-sleep:
PM: sleep: remove unreachable break
* pm-tools:
cpupower: speed up generating git version string
cpupowerutils: fix spelling mistake "dependant" -> "dependent"
* powercap:
powercap: Fix typo in Kconfig "Plance" -> "Plane"
powercap/intel_rapl: enumerate Psys RAPL domain together with package RAPL domain
powercap/intel_rapl: Fix domain detection
|
|
* pm-cpufreq:
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
cpufreq: Improve code around unlisted freq check
* pm-cpuidle:
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
|
|
Dirty logging is a key feature of the KVM MMU and must be supported by
the TDP MMU. Add support for both the write protection and PML dirty
logging modes.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-16-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When starting a HP machine with HIL driver but without an HIL keyboard
or HIL mouse attached, it may happen that data written to the HIL loop
gets stuck (e.g. because the transaction queue is full). Usually one
will then have to reboot the machine because all you see is and endless
output of:
Transaction add failed: transaction already queued?
In the higher layers hp_sdc_enqueue_transaction() is called to queued up
a HIL packet. This function returns an error code, and this patch adds
the necessary checks for this return code and disables the HIL driver if
further packets can't be sent.
Tested on a HP 730 and a HP 715/64 machine.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
|
|
With the set_fs change, we can no longer rely on copy_{to,from}_user()
accepting a kernel pointer, and it was bad form to do so anyway. Clean
this up and change the internal helper that io_uring uses to deal with
kernel pointers instead. This puts the offset copy in/out in __do_splice()
instead, which just calls the same helper.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull VFIO updates from Alex Williamson:
- New fsl-mc vfio bus driver supporting userspace drivers of objects
within NXP's DPAA2 architecture (Diana Craciun)
- Support for exposing zPCI information on s390 (Matthew Rosato)
- Fixes for "detached" VFs on s390 (Matthew Rosato)
- Fixes for pin-pages and dma-rw accesses (Yan Zhao)
- Cleanups and optimize vconfig regen (Zenghui Yu)
- Fix duplicate irq-bypass token registration (Alex Williamson)
* tag 'vfio-v5.10-rc1' of git://github.com/awilliam/linux-vfio: (30 commits)
vfio iommu type1: Fix memory leak in vfio_iommu_type1_pin_pages
vfio/pci: Clear token on bypass registration failure
vfio/fsl-mc: fix the return of the uninitialized variable ret
vfio/fsl-mc: Fix the dead code in vfio_fsl_mc_set_irq_trigger
vfio/fsl-mc: Fixed vfio-fsl-mc driver compilation on 32 bit
MAINTAINERS: Add entry for s390 vfio-pci
vfio-pci/zdev: Add zPCI capabilities to VFIO_DEVICE_GET_INFO
vfio/fsl-mc: Add support for device reset
vfio/fsl-mc: Add read/write support for fsl-mc devices
vfio/fsl-mc: trigger an interrupt via eventfd
vfio/fsl-mc: Add irq infrastructure for fsl-mc devices
vfio/fsl-mc: Added lock support in preparation for interrupt handling
vfio/fsl-mc: Allow userspace to MMAP fsl-mc device MMIO regions
vfio/fsl-mc: Implement VFIO_DEVICE_GET_REGION_INFO ioctl call
vfio/fsl-mc: Implement VFIO_DEVICE_GET_INFO ioctl
vfio/fsl-mc: Scan DPRC objects on vfio-fsl-mc driver bind
vfio: Introduce capability definitions for VFIO_DEVICE_GET_INFO
s390/pci: track whether util_str is valid in the zpci_dev
s390/pci: stash version in the zpci_dev
vfio/fsl-mc: Add VFIO framework skeleton for fsl-mc devices
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces support for the Mediatek MT9182 SCP and controlling
the Cortex R5F processors found in TI K3 platforms. It clones the
longstanding debugfs interface for controlling crash handling to
sysfs. Lastly it solves a bug where after a warm reset of Qualcomm
platforms the modem would crash upon first boot"
* tag 'rproc-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc/mediatek: Remove non-standard dsb()
remoteproc: Add recovery configuration to the sysfs interface
remoteproc: Add coredump as part of sysfs interface
remoteproc: Change default dump configuration to "disabled"
remoteproc: k3-r5: Add loading support for on-chip SRAM regions
remoteproc: k3-r5: Initialize TCM memories for ECC
remoteproc: k3-r5: Add a remoteproc driver for R5F subsystem
dt-bindings: remoteproc: Add bindings for R5F subsystem on TI K3 SoCs
remoteproc/mediatek: Add support for mt8192 SCP
remoteproc: Fixup coredump debugfs disable request
remoteproc: qcom_q6v5: Assign mpss region to Q6 before MBA boot
remoteproc/mediatek: fix null pointer dereference on null scp pointer
remoteproc: stm32: Fix pointer assignement
remoteproc: scp: add COMPILE_TEST dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"The siginificant new ext4 feature this time around is Harshad's new
fast_commit mode.
In addition, thanks to Mauricio for fixing a race where mmap'ed pages
that are being changed in parallel with a data=journal transaction
commit could result in bad checksums in the failure that could cause
journal replays to fail.
Also notable is Ritesh's buffered write optimization which can result
in significant improvements on parallel write workloads. (The kernel
test robot reported a 330.6% improvement on fio.write_iops on a 96
core system using DAX)
Besides that, we have the usual miscellaneous cleanups and bug fixes"
Link: https://lore.kernel.org/r/20200925071217.GO28663@shao2-debian
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (46 commits)
ext4: fix invalid inode checksum
ext4: add fast commit stats in procfs
ext4: add a mount opt to forcefully turn fast commits on
ext4: fast commit recovery path
jbd2: fast commit recovery path
ext4: main fast-commit commit path
jbd2: add fast commit machinery
ext4 / jbd2: add fast commit initialization
ext4: add fast_commit feature and handling for extended mount options
doc: update ext4 and journalling docs to include fast commit feature
ext4: Detect already used quota file early
jbd2: avoid transaction reuse after reformatting
ext4: use the normal helper to get the actual inode
ext4: fix bs < ps issue reported with dioread_nolock mount opt
ext4: data=journal: write-protect pages on j_submit_inode_data_buffers()
ext4: data=journal: fixes for ext4_page_mkwrite()
jbd2, ext4, ocfs2: introduce/use journal callbacks j_submit|finish_inode_data_buffers()
jbd2: introduce/export functions jbd2_journal_submit|finish_inode_data_buffers()
ext4: introduce ext4_sb_bread_unmovable() to replace sb_bread_unmovable()
ext4: use ext4_sb_bread() instead of sb_bread()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull initial set_fs() removal from Al Viro:
"Christoph's set_fs base series + fixups"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Allow a NULL pos pointer to __kernel_read
fs: Allow a NULL pos pointer to __kernel_write
powerpc: remove address space overrides using set_fs()
powerpc: use non-set_fs based maccess routines
x86: remove address space overrides using set_fs()
x86: make TASK_SIZE_MAX usable from assembly code
x86: move PAGE_OFFSET, TASK_SIZE & friends to page_{32,64}_types.h
lkdtm: remove set_fs-based tests
test_bitmap: remove user bitmap tests
uaccess: add infrastructure for kernel builds with set_fs()
fs: don't allow splice read/write without explicit ops
fs: don't allow kernel reads and writes without iter ops
sysctl: Convert to iter interfaces
proc: add a read_iter method to proc proc_ops
proc: cleanup the compat vs no compat file ops
proc: remove a level of indentation in proc_get_inode
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-10-22
1) Fix enforcing NULL check in verifier for new helper return types of
RET_PTR_TO_{BTF_ID,MEM_OR_BTF_ID}_OR_NULL, from Martin KaFai Lau.
2) Fix bpf_redirect_neigh() helper API before it becomes frozen by adding
nexthop information as argument, from Toke Høiland-Jørgensen.
3) Guard & fix compilation of bpf_tail_call_static() when __bpf__ arch is
not defined by compiler or clang too old, from Daniel Borkmann.
4) Remove misplaced break after return in attach_type_to_prog_type(), from
Tom Rix.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
