| Age | Commit message (Collapse) | Author |
|---|
|
Change struct ib_class_port_info to conform to IB Spec 1.3
That in order to get specific capability mask from ClassPortInfo mad.
>From the IB Spec, ClassPortInfo section:
"CapabilityMask2 Bits 0-26: Additional class-specific capabilities...
RespTimeValue the rest 5 bits"
The new struct now has one field for capabilitymask2 (previously was the
reserved field) and the resp_time field.
And it fixes up qib and srpt, use of the field repurposed to be used as
capabilitymask2:
IB/qib: Change pma_get_classportinfo
IB/srpt: Adjust the use of ib_class_port_info
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In ib_mad.h, ib_mad_snoop_handler uses send_buf rather than send_wr
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Stop abusing wr_id and just pass the parameter explicitly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Receipt of CM MAD with other than the Send method for an attribute
other than the ClassPortInfo attribute is invalid.
CM attributes other than ClassPortInfo only use the send method.
The SRP initiator does not maintain a timeout policy for CM connect
requests relies on the CM layer to do that. The result was that
the SRP initiator hung as the connect request never completed.
A new SRP target has been observed to respond to Send CM REQ
with GetResp of CM REQ with bad status. This is non conformant
with IBA spec but exposes a vulnerability in the current MAD/CM
code which will respond to the incoming GetResp of CM REQ as if
it was a valid incoming Send of CM REQ rather than tossing
this on the floor. It also causes the MAD layer not to
retransmit the original REQ even though it has not received a REP.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When the hfi1 driver was added these definitions were moved from the qib driver
to ib_mad.h to be used by both qib and hfi1. They should have been moved to
ib_smi.h instead.
Fixes: d4ab347005fb ("IB/core: Add core header changes needed for OPA")
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove the unused IB_NOTICE_REPRESS_* defines.
When the hfi1 driver was added these definitions were moved from the qib driver
to ib_mad.h. They should have been removed instead.
Fixes: d4ab347005fb ("IB/core: Add core header changes needed for OPA")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The pd now has a local_dma_lkey member which completely replaces
ib_get_dma_mr, use it instead.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds the value of the CNP opcode to the existing list of enumerated
opcodes in ib_pack.h
Add common OPA header definitions for driver
build:
- opa_port_info.h
- opa_smi.h
- hfi1_user.h
Additionally, ib_mad.h, has additional definitions
that are common to ib_drivers including:
- trap support
- cca support
The qib driver has the duplication removed in favor
those in ib_mad.h
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: John, Jubin <jubin.john@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
For devices which support OPA MADs
1) Use previously defined SMP support functions.
2) Pass correct base version to ib_create_send_mad when processing OPA MADs.
3) Process out_mad_key_index returned by agents for a response. This is
necessary because OPA SMP packets must carry a valid pkey.
4) Carry the correct segment size (OPA vs IBTA) of RMPP messages within
ib_mad_recv_wc.
5) Handle variable length OPA MADs by:
* Adjusting the 'fake' WC for locally routed SMP's to represent the
proper incoming byte_len
* out_mad_size is used from the local HCA agents
1) when sending agent responses on the wire
2) when passing responses through the local_completions
function
NOTE: wc.byte_len includes the GRH length and therefore is different
from the in_mad_size specified to the local HCA agents.
out_mad_size should _not_ include the GRH length as it is added
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch is the first of 3 which adds processing of OPA MADs
1) Add Intel Omni-Path Architecture defines
2) Increase max management version to accommodate OPA
3) update ib_create_send_mad
If the device supports OPA MADs and the MAD being sent is the OPA base
version alter the MAD size and sg lengths as appropriate
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add max MAD size to the device immutable data set and have all drivers that
support MADs report the current IB MAD size (IB_MGMT_MAD_SIZE) to the core.
Verify MAD size data in both the MAD core and when reading the immutable data.
OPA drivers will report alternate MAD sizes in subsequent patches.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In preparation to support the new OPA MAD Base version, add a base version
parameter to ib_create_send_mad and set it to IB_MGMT_BASE_VERSION for current
users.
Definition of the new base version and it's processing will occur in later
patches.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The following functions only need read access to the data passed to them.
ib_mad_kernel_rmpp_agent
is_rmpp_data_mad
rcv_has_same_gid
ib_find_send_mad
Clarify with const specifiers
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
ib_response_mad only needs read access to the MAD header, not write access
to the entire mad struct, so replace struct ib_mad with const struct
ib_mad_hdr
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Using the new registration mechanism, define a flag that indicates the
user wishes to process RMPP messages in user space rather than have
the kernel process them.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Registrations options are specified through flags. Definitions of flags will
be in subsequent patches.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
It needs parentheses around the argument, so that it can be used with
complex arguments (e.g., "n+5").
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Add defines for MAD error codes so that they can be used when
returning error responses.
Signed-off-by: Swapna Thete <swapna.thete@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
'mlx4', 'mthca', 'nes' and 'sysfs' into for-next
|
|
Fix ib_set_rmpp_flags() to use the correct bit mask for RRespTime. In
the 8-bit field of the RMPP header, the first 5 bits are RRespTime and
next 3 bits are RMPPFlags. Hence to retain the first 5 bits, the mask
should be 0xF8 instead of 0xF1.
ack_recv()-->format_ack() calls ib_set_rmpp_flags() and due to the
incorrect ANDing with 0xF1, RRespTime got changed incorrectly and RMPP
Acks sent back always had a RRespTime of 0x1E (30) which caused the
other end to consider the time outs to be approximately 4297 seconds
(i.e. in the order of 4*2^30) instead of the usual ~4 seconds (order
of 4*2^20).
Signed-off-by: Ramachandra K <ramachandra.kuchimanchi@qlogic.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The base versions handle constant folding just fine, use them
directly. The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.
This patch does not affect code generation at all.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Remove subversion $Id lines and improve readability by fixing other
coding style problems pointed out by checkpatch.pl.
Signed-off-by: Dotan Barak <dotanba@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
To allow ULPs to tune timeout values and capture retry statistics,
report the number of times that a mad send operation was retried.
For RMPP mads, report the total number of times that the any portion
(send window) of the send operation was retried.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ib_mad.h uses struct list_head, so while linux/list.h seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include linux/list.h directly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
MADs sent to the SA should use the the default P_Key (0x7fff/0xffff).
There's no requirement that the default P_Key is stored at index 0 in
the local P_Key table, so add code to the sa_query module to look up
the index of the default P_Key when creating an address handle for the
SA (which is done any time the P_Key table might change), and use this
index for all SA queries.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port). Without this, RMPP transactions get aborted because
of duplicate packets.
This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add RMPP support for additional management classes that support it.
Also, validate RMPP is consistent with management class specified.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add support for sending and receiving large RMPP transfers. The old
code supports transfers only as large as a single contiguous kernel
memory allocation. This patch uses linked list of memory buffers when
sending and receiving data to avoid needing contiguous pages for
larger transfers.
Receive side: copy the arriving MADs in chunks instead of coalescing
to one large buffer in kernel space.
Send side: split a multipacket MAD buffer to a list of segments,
(multipacket_list) and send these using a gather list of size 2.
Also, save pointer to last sent segment, and retrieve requested
segments by walking list starting at last sent segment. Finally,
save pointer to last-acked segment. When retrying, retrieve
segments for resending relative to this pointer. When updating last
ack, start at this pointer.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The MAD layer was violating the DMA API by touching data buffers used
for sends after the DMA mapping was done. This causes problems on
non-cache-coherent architectures, because the device doing DMA won't
see updates to the payload buffers that exist only in the CPU cache.
Fix this by having all MAD consumers use ib_create_send_mad() to
allocate their send buffers, and moving the DMA mapping into the MAD
layer so it can be done just before calling send (and after any
modifications of the send buffer by the MAD layer).
Tested on a non-cache-coherent PowerPC 440SPe system.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Clean up code by using enums instead of hard-coded magic numbers.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add structure definition for ClassPortInfo format. This is
needed for (at least) handling CM redirects.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
