| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
* tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: enable acpi support in RCPM driver
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
tty: serial: ucc_uart: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: qe: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: guts: fix comment syntax in file
soc: fsl: guts: remove unneeded semicolon
soc: fsl: qe: Use DEFINE_SPINLOCK() for spinlock
soc: fsl: qbman: Delete useless kfree code
soc: fsl: qbman: Ensure device cleanup is run for kexec
Link: https://lore.kernel.org/r/20210409205719.27927-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.13 - Tegra SoC
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
* tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory: tegra20: mc: Convert to schema
dt-bindings: memory: tegra124: emc: Replace core regulator with power domain
dt-bindings: memory: tegra30: emc: Replace core regulator with power domain
dt-bindings: memory: tegra20: emc: Replace core regulator with power domain
memory: tegra: Print out info-level once per driver probe
memory: tegra20: Protect debug code with a lock
memory: tegra20: Correct comment to MC_STAT registers writes
memory: tegra20: Add debug statistics
memory: tegra: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
Link: https://lore.kernel.org/r/20210407161333.73013-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.
There is a new user coming with the same constant in use. It will also
make its life easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 6ac9b61786cc64ae5cbfb69413137656f72e8204.
This commit was required because at that time, ioread/iowrite
functions were sub-optimal on powerpc/32 compared to the
architecture specific in_/out_ IO accessors.
But there are now equivalent since
commit 894fa235eb4c ("powerpc: inline iomap accessors").
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Add debug statistics collection support. The statistics is available
via debugfs in '/sys/kernel/debug/mc/stats', it shows percent of memory
controller utilization for each memory client. This information is
intended to help with debugging of memory performance issues, it already
was proven to be useful by helping to improve memory bandwidth management
of the display driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210319130933.23261-1-digetx@gmail.com
|
|
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
1637 | void at91_pinctrl_gpio_suspend(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
1661 | void at91_pinctrl_gpio_resume(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Cc: Russell King <linux@armlinux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210303124149.3149511-1-lee.jones@linaro.org
|
|
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It'll simplify the firmware handling for most consumers.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.
Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.
I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.
We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.
We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new PGID that is used not to forward frames anywhere. It is used
by MRP to make sure that MRP Test frames will not reach CPU port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
|
|
Add a clock provider driver for the Canaan Kendryte K210 RISC-V SoC.
This new driver with the compatible string "canaan,k210-clk" implements
support for the full clock structure of the K210 SoC. Since it is
required for the correct operation of the SoC, this driver is
selected by default for compilation when the SOC_CANAAN option is
selected.
With this change, the k210-sysctl driver is turned into a simple
platform driver which enables its power bus clock and triggers
populating its child nodes. The sysctl driver retains the SOC early
initialization code, but the implementation now relies on the new
function k210_clk_early_init() provided by the new clk-k210 driver.
The clock structure implemented and many of the coding ideas for the
driver come from the work by Sean Anderson on the K210 support for the
U-Boot project.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM SMMU and Mediatek updates from Will Deacon:
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU perf driver to be built independently from IOMMU
- Some tidy-up in IOVA and core code
- Conversion of the AMD IOMMU code to use the generic IO-page-table
framework
- Intel VT-d updates from Lu Baolu:
- Audit capability consistency among different IOMMUs
- Add SATC reporting structure support
- Add iotlb_sync_map callback support
- SDHI support for Renesas IOMMU driver
- Misc cleanups and other small improvments
* tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (94 commits)
iommu/amd: Fix performance counter initialization
MAINTAINERS: repair file pattern in MEDIATEK IOMMU DRIVER
iommu/mediatek: Fix error code in probe()
iommu/mediatek: Fix unsigned domid comparison with less than zero
iommu/vt-d: Parse SATC reporting structure
iommu/vt-d: Add new enum value and structure for SATC
iommu/vt-d: Add iotlb_sync_map callback
iommu/vt-d: Move capability check code to cap_audit files
iommu/vt-d: Audit IOMMU Capabilities and add helper functions
iommu/vt-d: Fix 'physical' typos
iommu: Properly pass gfp_t in _iommu_map() to avoid atomic sleeping
iommu/vt-d: Fix compile error [-Werror=implicit-function-declaration]
driver/perf: Remove ARM_SMMU_V3_PMU dependency on ARM_SMMU_V3
MAINTAINERS: Add entry for MediaTek IOMMU
iommu/mediatek: Add mt8192 support
iommu/mediatek: Remove unnecessary check in attach_device
iommu/mediatek: Support master use iova over 32bit
iommu/mediatek: Add iova reserved function
iommu/mediatek: Support for multi domains
iommu/mediatek: Add get_domain_id from dev->dma_range_map
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released() function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not belong into
any other subsystem, most of them living in drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere"
* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
soc: aspeed: socinfo: Add new systems
soc: aspeed: snoop: Add clock control logic
memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
optee: simplify i2c access
drivers: soc: atmel: fix type for same7
tee: optee: remove need_resched() before cond_resched()
soc: qcom: ocmem: don't return NULL in of_get_ocmem
optee: sync OP-TEE headers
tee: optee: fix 'physical' typos
drivers: optee: use flexible-array member instead of zero-length array
tee: fix some comment typos in header files
soc: ti: k3-ringacc: Use of_device_get_match_data()
soc: ti: pruss: Refactor the CFG sub-module init
soc: mediatek: pm-domains: Don't print an error if child domain is deferred
soc: mediatek: pm-domains: Add domain regulator supply
dt-bindings: power: Add domain regulator supply
soc: mediatek: cmdq: Remove cmdq_pkt_flush()
soc: mediatek: pm-domains: Add support for mt8167
...
|
|
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.
We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.
Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not be unconditionally enabling address learning, since doing
that is actively detrimential when a port is standalone and not offloading
a bridge. Namely, if a port in the switch is standalone and others are
offloading the bridge, then we could enter a situation where we learn an
address towards the standalone port, but the bridged ports could not
forward the packet there, because the CPU is the only path between the
standalone and the bridged ports. The solution of course is to not
enable address learning unless the bridge asks for it.
We need to set up the initial port flags for no learning and flooding
everything, and also when the port joins and leaves the bridge.
The flood configuration was already configured ok for standalone mode
in ocelot_init, we just need to disable learning in ocelot_init_port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation of offloading the bridge port flags which have
independent settings for unknown multicast and for broadcast, we should
also start reserving one destination Port Group ID for the flooding of
broadcast packets, to allow configuring it individually.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for 5.12
The socinfo driver gains support for dumping information about the platform's
PMICs, as well as new definitions for a number of platforms. The LLCC driver
gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
support for MSM8994 power domains. In addition to this it contains a few minor
fixes in the ocmem, rpmh and llcc drivers.
* tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ocmem: don't return NULL in of_get_ocmem
soc: qcom: socinfo: Remove unwanted le32_to_cpu()
soc: qcom: aoss: Add SM8350 compatible
drivers: soc: qcom: rpmpd: Add msm8994 RPM Power Domains
soc: qcom: socinfo: Fix an off by one in qcom_show_pmic_model()
soc: qcom: socinfo: Fix off-by-one array index bounds check
soc: qcom: socinfo: Add MDM9607 IDs
soc: qcom: socinfo: Add SoC IDs for APQ/MSM8998
soc: qcom: socinfo: Add SoC IDs for 630 family
soc: qcom: socinfo: Open read access to all for debugfs
soc: qcom: socinfo: add info from PMIC models array
soc: qcom: socinfo: add several PMIC IDs
soc: qcom: socinfo: add qrb5165 SoC ID
soc: qcom: rpmh: Remove serialization of TCS commands
soc: qcom: smem: use %*ph to print small buffer
dt-bindings: soc: qcom: convert qcom,smem bindings to yaml
drivers: qcom: rpmh-rsc: Do not read back the register write on trigger
soc: qcom: llcc-qcom: Add support for SM8250 SoC
soc: qcom: llcc-qcom: Extract major hardware version
dt-bindings: msm: Add LLCC for SM8250
Link: https://lore.kernel.org/r/20210204052258.388890-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot switch has been supporting LAG offload since its initial
commit, however felix could not make use of that, due to lack of a LAG
abstraction in DSA. Now that we have that, let's forward DSA's calls
towards the ocelot library, who will deal with setting up the bonding.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.
Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.
Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.
In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.
We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
into arm/drivers
This pull request contains Broadcom SoCs drivers changes for 5.12,
please pull the following:
- Rafal adds support for the Power Management Bus (PMB) which is used in
a variety of DSL/Cable modem/STB SoCs with a primary target being the
4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
get the chip identification (family and revision) to permit the
Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB
- Florian removes an unused function and its header
* tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Remove soc_is_brcmstb()
soc: bcm: brcmstb: add stubs for getting platform IDs
soc: bcm: add PM driver for Broadcom's PMB
dt-bindings: power: document Broadcom's PMB binding
Link: https://lore.kernel.org/r/20210131221721.685974-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.12 - Tegra SoC
1. Make the tegra124-emc driver modular.
2. Add interconnect support to Tegra124 memory controller drivers.
3. Minor fixes.
* tag 'memory-controller-drv-tegra-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: tegra: Remove calls to dev_pm_opp_set_clkname()
memory: tegra: Check whether reset is already asserted
memory: tegra124: Support interconnect framework
memory: tegra124-emc: Continue probing if timings are missing in device-tree
memory: tegra124-emc: Make driver modular
Link: https://lore.kernel.org/r/20210131180109.11510-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.12
1. Mediatek SMI: fix PM usage counter and make the driver modular.
2. Renesas RPC-IF: add support for RZ/G2 series.
3. Minor fixes.
* tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: mtk-smi: Allow building as module
memory: ti-aemif: Drop child node when jumping out loop
memory: mtk-smi: Use platform_register_drivers
memory: renesas-rpc-if: Add RZ/G2 to Kconfig description
dt-bindings: memory: renesas,rpc-if: Add support for RZ/G2 Series
memory: emif: Use DEFINE_SPINLOCK() for spinlock
memory: mtk-smi: Fix PM usage counter unbalance in mtk_smi ops
Link: https://lore.kernel.org/r/20210131180109.11510-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into arm/smmu
Arm SMMU updates for 5.12
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
|
|
After extending v7s, our pagetable already support iova reach
16GB(34bit). the master got the iova via dma_alloc_attrs may reach
34bits, but its HW register still is 32bit. then how to set the
bit32/bit33 iova? this depend on a SMI larb setting(bank_sel).
we separate whole 16GB iova to four banks:
bank: 0: 0~4G; 1: 4~8G; 2: 8-12G; 3: 12-16G;
The bank number is (iova >> 32).
We will preassign which bank the larbs belong to. currently we don't
have a interface for master to adjust its bank number.
Each a bank is a iova_region which is a independent iommu-domain.
the iova range for each iommu-domain can't cross 4G.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> #for memory part
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-31-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Use the common memory header(larb-port) in the source code.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-9-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Unlike sja1105, the only other user of the software-defined tag_8021q.c
tagger format, the implementation we choose for the Felix DSA switch
driver preserves full functionality under a vlan_filtering bridge
(i.e. IP termination works through the DSA user ports under all
circumstances).
The tag_8021q protocol just wants:
- Identifying the ingress switch port based on the RX VLAN ID, as seen
by the CPU. We achieve this by using the TCAM engines (which are also
used for tc-flower offload) to push the RX VLAN as a second, outer
tag, on egress towards the CPU port.
- Steering traffic injected into the switch from the network stack
towards the correct front port based on the TX VLAN, and consuming
(popping) that header on the switch's egress.
A tc-flower pseudocode of the static configuration done by the driver
would look like this:
$ tc qdisc add dev <cpu-port> clsact
$ for eth in swp0 swp1 swp2 swp3; do \
tc filter add dev <cpu-port> egress flower indev ${eth} \
action vlan push id <rxvlan> protocol 802.1ad; \
tc filter add dev <cpu-port> ingress protocol 802.1Q flower
vlan_id <txvlan> action vlan pop \
action mirred egress redirect dev ${eth}; \
done
but of course since DSA does not register network interfaces for the CPU
port, this configuration would be impossible for the user to do. Also,
due to the same reason, it is impossible for the user to inadvertently
delete these rules using tc. These rules do not collide in any way with
tc-flower, they just consume some TCAM space, which is something we can
live with.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Context: Ocelot switches put the injection/extraction frame header in
front of the Ethernet header. When used in NPI mode, a DSA master would
see junk instead of the destination MAC address, and it would most
likely drop the packets. So the Ocelot frame header can have an optional
prefix, which is just "ff:ff:ff:ff:ff:fe > ff:ff:ff:ff:ff:ff" padding
put before the actual tag (still before the real Ethernet header) such
that the DSA master thinks it's looking at a broadcast frame with a
strange EtherType.
Unfortunately, a lesson learned in commit 69df578c5f4b ("net: mscc:
ocelot: eliminate confusion between CPU and NPI port") seems to have
been forgotten in the meanwhile.
The CPU port module and the NPI port have independent settings for the
length of the tag prefix. However, the driver is using the same variable
to program both of them.
There is no reason really to use any tag prefix with the CPU port
module, since that is not connected to any Ethernet port. So this patch
makes the inj_prefix and xtr_prefix variables apply only to the NPI
port (which the switchdev ocelot_vsc7514 driver does not use).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We will be adding some private VCAP filters that should not interfere in
any way with the filters added using tc-flower. So we need to allocate
some IDs which will not be used by tc.
Currently ocelot uses an u32 id derived from the flow cookie, which in
itself is an unsigned long. This is a problem in itself, since on 64 bit
systems, sizeof(unsigned long)=8, so the driver is already truncating
these.
Create a struct ocelot_vcap_id which contains the full unsigned long
cookie from tc, as well as a boolean that is supposed to namespace the
filters added by tc with the ones that aren't.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Felix driver will need to preinstall some VCAP filters for its
tag_8021q implementation (outside of the tc-flower offload logic), so
these need to be exported to the common includes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have no in tree or out of tree users of this function, remove it and
the header providing its prototype.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add support for building the SMI driver as module. Switch MTK_SMI to
tristate, and add module_exit/module_license.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210126060055.11050-1-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The bd_mem_part member of ucc_geth_info always has the value
MEM_PART_SYSTEM, and AFAICT, there has never been any code setting it
to any other value. Moreover, muram is a somewhat precious resource,
so there's no point using that when normal memory serves just as well.
Apart from removing a lot of dead code, this is also motivated by
wanting to clean up the "store result from kmalloc() in a u32" mess.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper that takes a virtual address rather than the muram
offset. This will be used in a couple of places to avoid having to
store both the offset and the virtual address, as well as removing
NULL checks from the callers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow passing const-qualified pointers without requiring a cast in the
caller.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
