Age | Commit message (Collapse) | Author |
|
commit d8e42a2b0addf238be8b3b37dcd9795a5c1be459 upstream.
If the user set an MTU value, it usually means that there are special
requirements for the MTU. But if an interface gots activated, the MTU was
always recalculated and then the user set value was overwritten.
The only reason why this user set value has to be overwritten, is when the
MTU has to be decreased because batman-adv is not able to transfer packets
with the user specified size.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6a953cce8d0438391e6da48c8d0793d3fbfcfa6 upstream.
If an interface changes the MTU, it is expected that an NETDEV_PRECHANGEMTU
and NETDEV_CHANGEMTU notification events is triggered. This worked fine for
.ndo_change_mtu based changes because core networking code took care of it.
But for auto-adjustments after hard-interfaces changes, these events were
simply missing.
Due to this problem, non-batman-adv components weren't aware of MTU changes
and thus couldn't perform their own tasks correctly.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The system hangs up when batman-adv soft-interface is created on
hard-interface with small MTU. For example, the following commands
create batman-adv soft-interface on dummy interface with zero MTU:
# ip link add name dummy0 type dummy
# ip link set mtu 0 dev dummy0
# ip link set up dev dummy0
# ip link add name bat0 type batadv
# ip link set dev dummy0 master bat0
These commands cause the system hang up with the following messages:
[ 90.578925][ T6689] batman_adv: bat0: Adding interface: dummy0
[ 90.580884][ T6689] batman_adv: bat0: The MTU of interface dummy0 is too small (0) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 90.586264][ T6689] batman_adv: bat0: Interface activated: dummy0
[ 90.590061][ T6689] batman_adv: bat0: Forced to purge local tt entries to fit new maximum fragment MTU (-320)
[ 90.595517][ T6689] batman_adv: bat0: Forced to purge local tt entries to fit new maximum fragment MTU (-320)
[ 90.598499][ T6689] batman_adv: bat0: Forced to purge local tt entries to fit new maximum fragment MTU (-320)
This patch fixes this issue by returning error when enabling
hard-interface with small MTU size.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Most protocol-specific pointers in struct net_device are under
a respective ifdef. Wireless is the notable exception. Since
there's a sizable number of custom-built kernels for datacenter
workloads which don't build wireless it seems reasonable to
ifdefy those pointers as well.
While at it move IPv4 and IPv6 pointers up, those are special
for obvious reasons.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> # ieee802154
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/batman-adv/hard-interface.c
commit 690bb6fb64f5 ("batman-adv: Request iflink once in batadv-on-batadv check")
commit 6ee3c393eeb7 ("batman-adv: Demote batadv-on-batadv skip error message")
https://lore.kernel.org/all/20220302163049.101957-1-sw@simonwunderlich.de/
net/smc/af_smc.c
commit 4d08b7b57ece ("net/smc: Fix cleanup when register ULP fails")
commit 462791bbfa35 ("net/smc: add sysctl interface for SMC")
https://lore.kernel.org/all/20220302112209.355def40@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ifindex doesn't have to be unique for multiple network namespaces on
the same machine.
$ ip netns add test1
$ ip -net test1 link add dummy1 type dummy
$ ip netns add test2
$ ip -net test2 link add dummy2 type dummy
$ ip -net test1 link show dev dummy1
6: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 96:81:55:1e:dd:85 brd ff:ff:ff:ff:ff:ff
$ ip -net test2 link show dev dummy2
6: dummy2: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 5a:3c:af:35:07:c3 brd ff:ff:ff:ff:ff:ff
But the batman-adv code to walk through the various layers of virtual
interfaces uses this assumption because dev_get_iflink handles it
internally and doesn't return the actual netns of the iflink. And
dev_get_iflink only documents the situation where ifindex == iflink for
physical devices.
But only checking for dev->netdev_ops->ndo_get_iflink is also not an option
because ipoib_get_iflink implements it even when it sometimes returns an
iflink != ifindex and sometimes iflink == ifindex. The caller must
therefore make sure itself to check both netns and iflink + ifindex for
equality. Only when they are equal, a "physical" interface was detected
which should stop the traversal. On the other hand, vxcan_get_iflink can
also return 0 in case there was currently no valid peer. In this case, it
is still necessary to stop.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_get_real_netdevice. And since some of the
ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_is_on_batman_iface. And since some of the
.ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The error message "Cannot find parent device" was shown for users of
macvtap (on batadv devices) whenever the macvtap was moved to a different
netns. This happens because macvtap doesn't provide an implementation for
rtnl_link_ops->get_link_net.
The situation for which this message is printed is actually not an error
but just a warning that the optional sanity check was skipped. So demote
the message from error to warning and adjust the text to better explain
what happened.
Reported-by: Leonardo Mörlein <freifunk@irrelefant.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit d2a8ebbf8192 ("kernel.h: split out container_of() and
typeof_member() macros") introduced a new header for the container_of
related macros from (previously) linux/kernel.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The check if a batman-adv related object is NULL or not is now directly in
the batadv_*_put functions. It is not needed anymore to perform this check
outside these function:
The changes were generated using a coccinelle semantic patch:
@@
expression E;
@@
- if (likely(E != NULL))
(
batadv_backbone_gw_put
|
batadv_claim_put
|
batadv_dat_entry_put
|
batadv_gw_node_put
|
batadv_hardif_neigh_put
|
batadv_hardif_put
|
batadv_nc_node_put
|
batadv_nc_path_put
|
batadv_neigh_ifinfo_put
|
batadv_neigh_node_put
|
batadv_orig_ifinfo_put
|
batadv_orig_node_put
|
batadv_orig_node_vlan_put
|
batadv_softif_vlan_put
|
batadv_tp_vars_put
|
batadv_tt_global_entry_put
|
batadv_tt_local_entry_put
|
batadv_tt_orig_list_entry_put
|
batadv_tt_req_node_put
|
batadv_tvlv_container_put
|
batadv_tvlv_handler_put
)(E);
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
If batadv_hardif_enable_interface is called then its called from its
callback ndo_add_slave. It is therefore not necessary to check if it is a
batadv interface.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batadv_hardif_enable_interface is now only called from the callback
ndo_add_slave. This callback is only used by do_set_master in the rtnetlink
code which only does two things:
1. remove the net_device from its old master
2. add the net_device to its new batadv master
The code to replicate the first step in batman-adv is therefore unused
since the sysfs code was dropped.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The sysfs code for the batman-adv/mesh_iface file was receiving a string of
the batadv interface. This interface name was then provided to the code
which shared sysfs+rtnetlink code for attaching an hard-interface to an
batadv interface. The rtnetlink code was also using the (extracted)
interface name from the ndo_add_slave callback to increase the shared code
- even when it would have been more efficient to use the provided
net_device object directly instead of searching it again (based on its
name) in batadv_hardif_enable_interface.
But this indirect handling is no longer necessary because the sysfs code
was dropped. There is now only a single code path which is using
batadv_hardif_enable_interface.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The sysfs code in batman-adv was could create a new batadv interfaces on
demand when a string (interface name) was written to the
batman-adv/mesh_iface file. But the code no longer exists in the current
batman-adv codebase. The helper code to implement this behavior must be
considered as unused and can be dropped.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Fix some spelling mistakes in comments:
containg ==> containing
dont ==> don't
datas ==> data
brodcast ==> broadcast
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv source code was using the year of publication (to net-next)
as "last" year for the copyright statement. The whole source code mentioned
in the MAINTAINERS "BATMAN ADVANCED" section was handled as a single entity
regarding the publishing year.
This avoided having outdated (in sense of year information - not copyright
holder) publishing information inside several files. But since the simple
"update copyright year" commit (without other changes) in the file was not
well received in the upstream kernel, the option to not have a copyright
year (for initial and last publication) in the files are chosen instead.
More detailed information about the years can still be retrieved from the
SCM system.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The only way to automatically drop batadv mesh interfaces when all soft
interfaces were removed was dropped with the sysfs support. It is no longer
needed to have them handled by kernel anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The debugfs support in batman-adv was marked as deprecated by the commit
00caf6a2b318 ("batman-adv: Mark debugfs functionality as deprecated") and
scheduled for removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The sysfs in batman-adv support was marked as deprecated by the commit
42cdd521487f ("batman-adv: ABI: Mark sysfs files as deprecated") and
scheduled for removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit b296a6d53339 ("kernel.h: split out min()/max() et al. helpers")
moved the min/max helper functionality from kernel.h to minmax.h. Adjust
the kernel code accordingly to avoid fragile indirect includes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
If a batman-adv packets has to be fragmented, then the original batman-adv
packet header is not stripped away. Instead, only a new header is added in
front of the packet after it was split.
This size must be considered to avoid cost intensive reallocations during
the transmission through the various device layers.
Fixes: 7bca68c7844b ("batman-adv: Add lower layer needed_(head|tail)room to own ones")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
checkpatch found various instances of "Possible repeated word" in various
comments.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_hardif_remove_interfaces was meant to remove all
interfaces which are currently in the list of known (compatible) hardifs
during module unload. But the function unregister_netdevice_notifier is
called in batadv_exit before batadv_hardif_remove_interfaces. This will
trigger NETDEV_UNREGISTER events for all available interfaces and in this
process remove all interfaces from batadv_hardif_list. And
batadv_hardif_remove_interfaces only operated on this (empty) list.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
In some setups multiple hard interfaces with similar link qualities
or throughput values are available. But people have expressed the desire
to consider one of them as a backup only.
Some creative solutions are currently in use: Such people are
configuring multiple batman-adv mesh/soft interfaces, wire them
together with some veth pairs and then tune the hop penalty to achieve
an effect similar to a tunable per interface hop penalty.
This patch introduces a new, configurable, per hard interface hop penalty
to simplify such setups.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
In commit a63fc6b75cca ("rcu: Upgrade rcu_swap_protected() to
rcu_replace_pointer()") a new helper macro named rcu_replace_pointer() was
introduced to simplify code requiring to switch an rcu pointer to a new
value while extracting the old one.
Use rcu_replace_pointer() where appropriate to make code slimer.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Each slave interface of an B.A.T.M.A.N. IV virtual interface has an OGM
packet buffer which is initialized using data from netdevice notifier and
other rtnetlink related hooks. It is sent regularly via various slave
interfaces of the batadv virtual interface and in this process also
modified (realloced) to integrate additional state information via TVLV
containers.
It must be avoided that the worker item is executed without a common lock
with the netdevice notifier/rtnetlink helpers. Otherwise it can either
happen that half modified/freed data is sent out or functions modifying the
OGM buffer try to access already freed memory regions.
Reported-by: syzbot+0cc629f19ccb8534935b@syzkaller.appspotmail.com
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Two cases of overlapping changes, nothing fancy.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care if debugfs works or not, this trickles back a bit
so we can clean things up by making some functions return void instead
of an error value that is never going to fail.
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[sven@narfation.org: drop unused variables]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The state of slave interfaces are handled differently depending on whether
the interface is up or not. All active interfaces (IFF_UP) will transmit
OGMs. But for B.A.T.M.A.N. IV, also non-active interfaces are scheduling
(low TTL) OGMs on active interfaces. The code which setups and schedules
the OGMs must therefore already be called when the interfaces gets added as
slave interface and the transmit function must then check whether it has to
send out the OGM or not on the specific slave interface.
But the commit f0d97253fb5f ("batman-adv: remove ogm_emit and ogm_schedule
API calls") moved the setup code from the enable function to the activate
function. The latter is called either when the added slave was already up
when batadv_hardif_enable_interface processed the new interface or when a
NETDEV_UP event was received for this slave interfac. As result, each
NETDEV_UP would schedule a new OGM worker for the interface and thus OGMs
would be send a lot more than expected.
Fixes: f0d97253fb5f ("batman-adv: remove ogm_emit and ogm_schedule API calls")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit 54d50897d544 ("linux/kernel.h: split *_MAX and *_MIN macros into
<linux/limits.h>") moved the U32_MAX/INT_MAX/ULONG_MAX from linux/kernel.h
to linux/limits.h. Adjust the includes accordingly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
All files got a SPDX-License-Identifier with commit 7db7d9f369a4
("batman-adv: Add SPDX license identifier above copyright header"). All the
required information about the license conditions can be found in
LICENSES/.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
It is not allowed to use WARN* helpers on potential incorrect input from
the user or transient problems because systems configured as panic_on_warn
will reboot due to such a problem.
A NULL return value of __dev_get_by_index can be caused by various problems
which can either be related to the system configuration or problems
(incorrectly returned network namespaces) in other (virtual) net_device
drivers. batman-adv should not cause a (harmful) WARN in this situation and
instead only report it via a simple message.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Reported-by: syzbot+c764de0fcfadca9a8595@syzkaller.appspotmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
batman-adv is creating special debugfs directories in the init
net_namespace for each created soft-interface (batadv net_device). But it
is possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new batadv net_device with
the name "bat0". batman-adv is then also adding a new directory under
$debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "bat1" and registers a
different batadv device with the name "bat0". batman-adv will then try to
create a directory with the name "bat0" under $debugfs/batman-adv/ again.
But there already exists one with this name under this path and thus this
fails. batman-adv will detect a problem and rollback the registering of
this device.
batman-adv must therefore take care of renaming the debugfs directories for
soft-interfaces whenever it detects such a net_device rename.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
batman-adv is creating special debugfs directories in the init
net_namespace for each valid hard-interface (net_device). But it is
possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new net_device which gets
the name "wlan0" assigned by default. batman-adv is also adding a new
directory under $debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "wl_pri" and registers a
different device. The kernel may now decide to use the name "wlan0" again
for this new device. batman-adv will detect it as a valid net_device and
tries to create a directory with the name "wlan0" under
$debugfs/batman-adv/. But there already exists one with this name under
this path and thus this fails. batman-adv will detect a problem and
rollback the registering of this device.
batman-adv must therefore take care of renaming the debugfs directories
for hard-interfaces whenever it detects such a net_device rename.
Fixes: 5bc7c1eb44f2 ("batman-adv: add debugfs structure for information per interface")
Reported-by: John Soros <sorosj@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
batman-adv uses internal indices for each enabled and active interface.
It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the
correct position in the ogm_cnt bitmaps.
The type for the number of enabled interfaces (which defines the next
interface index) was set to char. This type can be (depending on the
architecture) either signed (limiting batman-adv to 127 active slave
interfaces) or unsigned (limiting batman-adv to 255 active slave
interfaces).
This limit was not correctly checked when an interface was enabled and thus
an overflow happened. This was only catched on systems with the signed char
type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with
a negative size.
The if_num interface index was only a s16 and therefore significantly
smaller than the ifindex (int) used by the code net code.
Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be
(unsigned) int to support the same number of slave interfaces as the net
core code. And the interface activation code must check the number of
active slave interfaces to avoid integer overflows.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the kernel-doc documentation, externally visible functions
should be documented. This refers to all all non-static function which can
(and will) be used by functions in other sources files.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should
therefore be included instead of linux/fs.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The "Linux kernel licensing rules" require that each file has a SPDX
license identifier as first line (and sometimes as second line).
The FSFE REUSE practices [1] would also require the same tags but have no
restrictions on the placement in the source file. Using the "Linux kernel
licensing rules" is therefore also fulfilling the FSFE REUSE practices
requirements at the same time.
[1] https://reuse.software/practices/
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Cleanup patches to make checkpatch happy, by Sven Eckelmann (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|