| Age | Commit message (Collapse) | Author |
|---|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- ignore self-generated loop detect MAC addresses in translation table,
by Simon Wunderlich
- install uapi batman_adv.h header, by Sven Eckelmann
- bump copyright years, by Sven Eckelmann
- Remove an unused variable in translation table code, by Sven Eckelmann
- Handle NET_XMIT_CN like NET_XMIT_SUCCESS (revised according to Davids
suggestion), and a follow up code clean up, by Gao Feng (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The bridge loop avoidance (BLA) feature of batman-adv sends packets to
probe for Mesh/LAN packet loops. Those packets are not sent by real
clients and should therefore not be added to the translation table (TT).
Signed-off-by: Simon Wunderlich <simon.wunderlich@open-mesh.com>
|
|
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738376d ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f49b ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dacec ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A failure during the submission also causes dropped packets.
batadv_interface_tx should therefore also increase the DROPPED counter for
these returns.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
kfree_skb assumes that an skb is dropped after an failure and notes that.
consume_skb should be used in non-failure situations. Such information is
important for dropmonitor netlink which tells how many packets were dropped
and where this drop happened.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
With this patch, (re)broadcasting on a specific interfaces is avoided:
* No neighbor: There is no need to broadcast on an interface if there
is no node behind it.
* Single neighbor is source: If there is just one neighbor on an
interface and if this neighbor is the one we actually got this
broadcast packet from, then we do not need to echo it back.
* Single neighbor is originator: If there is just one neighbor on
an interface and if this neighbor is the originator of this
broadcast packet, then we do not need to echo it back.
Goodies for BATMAN V:
("Upgrade your BATMAN IV network to V now to get these for free!")
Thanks to the split of OGMv1 into two packet types, OGMv2 and ELP
that is, we can now apply the same optimizations stated above to OGMv2
packets, too.
Furthermore, with BATMAN V, rebroadcasts can be reduced in certain
multi interface cases, too, where BATMAN IV cannot. This is thanks to
the removal of the "secondary interface originator" concept in BATMAN V.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_sum_counter is only used in soft-interface.c and has no
special relevance for main.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_send_skb_unicast is not acquiring a reference for an
orig_node nor removing it from any datastructure. It still reduces the
reference counter for an object which is still in the hands of the caller.
This is confusing and can lead in the future to problems in the reference
handling of the caller function.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Postponing the removal of the interface breaks the expected behavior of
NETDEV_UNREGISTER and NETDEV_PRE_TYPE_CHANGE. This is especially
problematic when an interface is removed and added in quick succession.
This reverts commit 5bc44dc8458c ("batman-adv: postpone sysfs removal when
unregistering").
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The throughput meter module is a simple, kernel-space replacement for
throughtput measurements tool like iperf and netperf. It is intended to
approximate TCP behaviour.
It is invoked through batctl: the protocol is connection oriented, with
cumulative acknowledgment and a dynamic-size sliding window.
The test *can* be interrupted by batctl. A receiver side timeout avoids
unlimited waitings for sender packets: after one second of inactivity, the
receiver abort the ongoing test.
Based on a prototype from Edo Monticelli <montik@autistici.org>
Signed-off-by: Antonio Quartulli <antonio.quartulli@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- two patches with minimal clean up work by Antonio Quartulli and
Simon Wunderlich
- eight patches of B.A.T.M.A.N. V, API and documentation clean
up work, by Antonio Quartulli and Marek Lindner
- Andrew Lunn fixed the skb priority adoption when forwarding
fragmented packets (two patches)
- Multicast optimization support is now enabled for bridges which
comes with some protocol updates, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch changes relevant to a node's own multicast flags are
printed to the 'mcast' log level.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The bat_algo functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~15%, 103
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
To reduce the field pollution in our main batadv_priv data structure
we've already created some substructures so that we could group fields
in a convenient manner.
However gw_mode and gw_sel_class are still part of the main object.
More both fields to the GW private substructure.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.
Fixes: 5d2c05b21337 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
It is easier to understand that the returned value of a specific function
doesn't have to be 0 when the functions was successful when the actual
return type is bool. This is especially true when all surrounding functions
with return type int use negative values to return the error code.
Reported-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
When creating a soft interface, create it in the same netns as the
hard interface. Replace all references to init_net with the correct
name space for the interface being manipulated.
Suggested-by: Daniel Ehlers <danielehlers@mindeye.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The batX soft interface should not be moved between network name
spaces. This is similar to bridges, bonds, tunnels, which are not
allowed to move between network namespaces.
Suggested-by: Daniel Ehlers <danielehlers@mindeye.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The callers of batadv_interface_rx have to make sure that enough data can
be pulled from the skb when they read the batman-adv header. The only two
functions using it are either calling pskb_may_pull with hdr_size directly
(batadv_recv_bcast_packet) or indirectly via batadv_check_unicast_packet
(batadv_recv_unicast_packet).
Reported-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Antonio Quartulli says:
====================
pull request: batman-adv 20160504
In this pull request you have:
- two changes to the MAINTAINERS file where one marks our mailing list
as moderated and the other adds a missing documentation file
- kernel-doc fixes
- code refactoring and various cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:
struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)
Compile tested only.
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Antonio Quartulli <a@unstable.cc>
[sven@narfation.org: Fix additional names]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The encapsulated ethernet and VLAN header may be outside the received
ethernet frame. Thus the skb buffer size has to be checked before it can be
parsed to find out if it encapsulates another batman-adv packet.
Fixes: 420193573f11 ("batman-adv: softif bridge loop avoidance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The maximum of hard_header_len and maximum of all needed_(head|tail)room of
all slave interfaces of a batman-adv device must be used to define the
batman-adv device needed_(head|tail)room. This is required to avoid too
small buffer problems when these slave devices try to send the encapsulated
packet in a tx path without the possibility to resize the skbuff.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
(s|u)(8|16|32|64) are the preferred types in the kernel. The use of the
standard C99 types u?int(8|16|32|64)_t are objected by some people and even
checkpatch now warns about using them.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Antonio Quartulli says:
====================
Included changes:
- avoid integer overflow in GW selection routine
- prevent race condition by making capability bit changes atomic (use
clear/set/test_bit)
- fix synchronization issue in mcast tvlv handler
- fix crash on double list removal of TT Request objects
- fix leak by puring packets enqueued for sending upon iface removal
- ensure network header pointer is set in skb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The two commits noted below added calls to ip_hdr() and ipv6_hdr(). They
need a correctly set skb network header.
Unfortunately we cannot rely on the device drivers to set it for us.
Therefore setting it in the beginning of the according ndo_start_xmit
handler.
Fixes: 1d8ab8d3c176 ("batman-adv: Modified forwarding behaviour for multicast packets")
Fixes: ab49886e3da7 ("batman-adv: Add IPv4 link-local/IPv6-ll-all-nodes multicast support")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
batadv_softif_vlan_get() may return NULL which has to be verified
by the caller.
Fixes: 35df3b298fc8 ("batman-adv: fix TT VLAN inconsistency on VLAN re-add")
Reported-by: Ryan Thompson <ryan@eero.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The MAC address of the soft-interface is used to initialise
the "non-purge" TT entry of each existing VLAN. Therefore
when the user invokes ndo_set_mac_address() all the
"non-purge" TT entries have to be updated, not only the one
belonging to the non-tagged network.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.
Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.
The order for include blocks are:
* primary headers (main.h and the *.h file of a *.c file)
* global linux headers
* required local headers
* extra forward declarations for pointers in function/struct declarations
The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The current default settings for optional features in batman-adv seems to
be based around the idea that the user only compiles what he requires. They
will automatically enabled when they are compiled in. For example the
network coding part of batman-adv is by default disabled in the out-of-tree
module but will be enabled when the code is compiled during the module
build.
But distributions like Debian just enable all features of the batman-adv
kernel module and hope that more experimental features or features with
possible negative effects have to be enabled using some runtime
configuration interface.
The network_coding feature can help in specific setups but also has
drawbacks and is not disabled by default in the out-of-tree module.
Disabling by default in the runtime config seems to be also quite sane.
The bridge_loop_avoidance is the only feature which is disabled by default
but may be necessary even in simple setups. Packet loops may even be
created during the initial node setup when this is not enabled. This is
different than STP on bridges because mesh is usually used on Adhoc WiFi.
Having two nodes (by accident) in the same LAN segment and in the same mesh
network is rather common in this situation.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The default hop penalty is currently set to 15, which is applied like
that for multi interface devices (e.g. dual band APs). Single band
devices will still use an effective penalty of 30 (hop penalty + wifi
penalty).
After receiving reports of too long paths in mesh networks with dual
band APs which were fixed by increasing the hop penalty, we'd like to
suggest to increase that default value in the default setting as well.
We've evaluated that increase in a handful of medium sized mesh
networks (5-20 nodes) with single and dual band devices, with changes
for the better (shorter routes, higher throughput) or no change at all.
This patch changes the hop penalty to 30, which will give an effective
penalty of 60 on single band devices (hop penalty + wifi penalty).
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
