| Age | Commit message (Collapse) | Author |
|---|
|
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to kill PTP on a DSA switch completely and absolutely,
until a reboot, with a simple command:
tcpdump -i eth2 -j adapter_unsynced
where eth2 is the switch's DSA master.
Why? Well, in short, the PTP API in place today is a bit rudimentary and
relies on applications to retrieve the TX timestamps by polling the
error queue and looking at the cmsg structure. But there is no timestamp
identification of any sorts (except whether it's HW or SW), you don't
know how many more timestamps are there to come, which one is this one,
from whom it is, etc. In other words, the SO_TIMESTAMPING API is
fundamentally limited in that you can get a single HW timestamp from the
stack.
And the "-j adapter_unsynced" flag of tcpdump enables hardware
timestamping.
So let's imagine what happens when the DSA master decides it wants to
deliver TX timestamps to the skb's socket too:
- The timestamp that the user space sees is taken by the DSA master.
Whereas the RX timestamp will eventually be overwritten by the DSA
switch. So the RX and TX timestamps will be in different time bases
(aka garbage).
- The user space applications have no way to deal with the second (real)
TX timestamp finally delivered by the DSA switch, or even to know to
wait for it.
Take ptp4l from the linuxptp project, for example. This is its behavior
after running tcpdump, before the patch:
ptp4l[172]: [6469.594] Unexpected data on socket err queue:
ptp4l[172]: [6469.693] rms 8 max 16 freq -21257 +/- 11 delay 748 +/- 0
ptp4l[172]: [6469.711] Unexpected data on socket err queue:
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 05 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.721] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b1 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.838] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 06 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.848] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 13 02
ptp4l[172]: 0010 00 36 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 04 1a 45 05 7f
ptp4l[172]: 0030 00 00 5e 05 41 32 27 c2 1a 68 00 04 9f ff fe 05
ptp4l[172]: 0040 de 06 00 01
ptp4l[172]: [6469.855] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b2 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.974] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 07 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
The ptp4l program itself is heavily patched to show this (more details
here [0]). Otherwise, by default it just hangs.
On the other hand, with the DSA patch to disallow HW timestamping
applied:
tcpdump -i eth2 -j adapter_unsynced
tcpdump: SIOCSHWTSTAMP failed: Device or resource busy
So it is a fact of life that PTP timestamping on the DSA master is
incompatible with timestamping on the switch MAC, at least with the
current API. And if the switch supports PTP, taking the timestamps from
the switch MAC is highly preferable anyway, due to the fact that those
don't contain the queuing latencies of the switch. So just disallow PTP
on the DSA master if there is any PTP-capable switch attached.
[0]: https://sourceforge.net/p/linuxptp/mailman/message/36880648/
Fixes: 0336369d3a4d ("net: dsa: forward hardware timestamping ioctls to switch driver")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge the CPU port registers dump into the master interface registers
dump through ethtool, by nesting the ethtool_drvinfo and ethtool_regs
structures of the CPU port into the dump.
drvinfo->regdump_len will contain the full data length, while regs->len
will contain only the master interface registers dump length.
This allows for example to dump the CPU port registers on a ZII Dev
C board like this:
# ethtool -d eth1
0x004: 0x00000000
0x008: 0x0a8000aa
0x010: 0x01000000
0x014: 0x00000000
0x024: 0xf0000102
0x040: 0x6d82c800
0x044: 0x00000020
0x064: 0x40000000
0x084: RCR (Receive Control Register) 0x47c00104
MAX_FL (Maximum frame length) 1984
FCE (Flow control enable) 0
BC_REJ (Broadcast frame reject) 0
PROM (Promiscuous mode) 0
DRT (Disable receive on transmit) 0
LOOP (Internal loopback) 0
0x0c4: TCR (Transmit Control Register) 0x00000004
RFC_PAUSE (Receive frame control pause) 0
TFC_PAUSE (Transmit frame control pause) 0
FDEN (Full duplex enable) 1
HBC (Heartbeat control) 0
GTS (Graceful transmit stop) 0
0x0e4: 0x76735d6d
0x0e8: 0x7e9e8808
0x0ec: 0x00010000
.
.
.
88E6352 Switch Port Registers
------------------------------
00: Port Status 0x4d04
Pause Enabled 0
My Pause 1
802.3 PHY Detected 0
Link Status Up
Duplex Full
Speed 100 or 200 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0x4
01: Physical Control 0x003d
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Up
Force Link 1
Duplex's Forced value Full
Force Duplex 1
Force Speed 100 or 200 Mbps
.
.
.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Creating a macvtap on a DSA-backed interface results in the following
splat when lockdep is enabled:
[ 19.638080] IPv6: ADDRCONF(NETDEV_CHANGE): lan0: link becomes ready
[ 23.041198] device lan0 entered promiscuous mode
[ 23.043445] device eth0 entered promiscuous mode
[ 23.049255]
[ 23.049557] ============================================
[ 23.055021] WARNING: possible recursive locking detected
[ 23.060490] 5.0.0-rc3-00013-g56c857a1b8d3 #118 Not tainted
[ 23.066132] --------------------------------------------
[ 23.071598] ip/2861 is trying to acquire lock:
[ 23.076171] 00000000f61990cb (_xmit_ETHER){+...}, at: dev_set_rx_mode+0x1c/0x38
[ 23.083693]
[ 23.083693] but task is already holding lock:
[ 23.089696] 00000000ecf0c3b4 (_xmit_ETHER){+...}, at: dev_uc_add+0x24/0x70
[ 23.096774]
[ 23.096774] other info that might help us debug this:
[ 23.103494] Possible unsafe locking scenario:
[ 23.103494]
[ 23.109584] CPU0
[ 23.112093] ----
[ 23.114601] lock(_xmit_ETHER);
[ 23.117917] lock(_xmit_ETHER);
[ 23.121233]
[ 23.121233] *** DEADLOCK ***
[ 23.121233]
[ 23.127325] May be due to missing lock nesting notation
[ 23.127325]
[ 23.134315] 2 locks held by ip/2861:
[ 23.137987] #0: 000000003b766c72 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x338/0x4e0
[ 23.146231] #1: 00000000ecf0c3b4 (_xmit_ETHER){+...}, at: dev_uc_add+0x24/0x70
[ 23.153757]
[ 23.153757] stack backtrace:
[ 23.158243] CPU: 0 PID: 2861 Comm: ip Not tainted 5.0.0-rc3-00013-g56c857a1b8d3 #118
[ 23.166212] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
[ 23.172843] Call trace:
[ 23.175358] dump_backtrace+0x0/0x188
[ 23.179116] show_stack+0x14/0x20
[ 23.182524] dump_stack+0xb4/0xec
[ 23.185928] __lock_acquire+0x123c/0x1860
[ 23.190048] lock_acquire+0xc8/0x248
[ 23.193724] _raw_spin_lock_bh+0x40/0x58
[ 23.197755] dev_set_rx_mode+0x1c/0x38
[ 23.201607] dev_set_promiscuity+0x3c/0x50
[ 23.205820] dsa_slave_change_rx_flags+0x5c/0x70
[ 23.210567] __dev_set_promiscuity+0x148/0x1e0
[ 23.215136] __dev_set_rx_mode+0x74/0x98
[ 23.219167] dev_uc_add+0x54/0x70
[ 23.222575] macvlan_open+0x170/0x1d0
[ 23.226336] __dev_open+0xe0/0x160
[ 23.229830] __dev_change_flags+0x16c/0x1b8
[ 23.234132] dev_change_flags+0x20/0x60
[ 23.238074] do_setlink+0x2d0/0xc50
[ 23.241658] __rtnl_newlink+0x5f8/0x6e8
[ 23.245601] rtnl_newlink+0x50/0x78
[ 23.249184] rtnetlink_rcv_msg+0x360/0x4e0
[ 23.253397] netlink_rcv_skb+0xe8/0x130
[ 23.257338] rtnetlink_rcv+0x14/0x20
[ 23.261012] netlink_unicast+0x190/0x210
[ 23.265043] netlink_sendmsg+0x288/0x350
[ 23.269075] sock_sendmsg+0x18/0x30
[ 23.272659] ___sys_sendmsg+0x29c/0x2c8
[ 23.276602] __sys_sendmsg+0x60/0xb8
[ 23.280276] __arm64_sys_sendmsg+0x1c/0x28
[ 23.284488] el0_svc_common+0xd8/0x138
[ 23.288340] el0_svc_handler+0x24/0x80
[ 23.292192] el0_svc+0x8/0xc
This looks fairly harmless (no actual deadlock occurs), and is
fixed in a similar way to c6894dec8ea9 ("bridge: fix lockdep
addr_list_lock false positive splat") by putting the addr_list_lock
in its own lockdep class.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing static keyword.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A previous change tries to set the MTU on the master device to take
into account the DSA overheads. This patch tries to reset the master
device back to the default MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA tagging of frames sent over the master interface to the switch
increases the size of the frame. Such frames can then be bigger than
the normal MTU of the master interface, and it may drop them. Use the
overhead information from the tagger to set the MTU of the master
device to include this overhead.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While introducing the DSA tagging protocol attribute, it was added to the DSA
slave network devices, but those actually see untagged traffic (that is their
whole purpose). Correct this mistake by putting the tagging sysfs attribute
under the DSA master network device where this is the information that we need.
While at it, also correct the sysfs documentation mistake that missed the
"dsa/" directory component of the attribute.
Fixes: 98cdb4807123 ("net: dsa: Expose tagging protocol to user-space")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the same type of ethtool diversion that we have for
ETH_SS_STATS and make it work with ETH_SS_PHY_STATS. This allows
providing PHY level statistics for CPU ports that are directly
connecting to a PHY device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is completely redundant with what netdev_set_default_ethtool_ops()
does, we are always guaranteed to have a valid dev->ethtool_ops pointer,
however, within that structure, not all function calls may be populated,
so we still have to check them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DSA helpers to setup and teardown a master net device wired to its
CPU port. This centralizes the dsa_ptr assignment.
This also makes the master ethtool helpers static at the same time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With DSA, a master net device (CPU facing interface) has a dsa_ptr
pointer to which hangs a dsa_switch_tree. This is not correct because a
master interface is wired to a dedicated switch port, and because we can
theoretically have several master interfaces pointing to several CPU
ports of the same switch fabric.
Change the master interface's dsa_ptr for the CPU dsa_port pointer.
This is a step towards supporting multiple CPU ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make it clear that the master device is linked to a CPU port by using
"cpu_dp" for the dsa_port variable in master.c instead of "port", then
use a "port" variable to describe the port index, as usually seen in
other places of DSA core.
This will make the future patch touching dsa_ptr more readable. There is
no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA overrides the master device ethtool ops, so that it can inject stats
from its dedicated switch CPU port as well.
The related code is currently split in dsa.c and slave.c, but it only
scopes the master net device. Move it to a new master.c DSA core file.
This file will be later extented with master net device specific code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
