| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
|
|
Due to a confusion I thought that eth_type_trans() was called by the
network stack whereas it can actually be called by network drivers to
figure out the skb protocol and next packet_type handlers.
In light of the above, it is not safe to store the frame type from the
DSA tagger's .filter callback (first entry point on RX path), since GRO
is yet to be invoked on the received traffic. Hence it is very likely
that the skb->cb will actually get overwritten between eth_type_trans()
and the actual DSA packet_type handler.
Of course, what this patch fixes is the actual overwriting of the
SJA1105_SKB_CB(skb)->type field from the GRO layer, which made all
frames be seen as SJA1105_FRAME_TYPE_NORMAL (0).
Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
|
|
Tools like tcpdump need to be able to decode the significance of fake
VLAN headers that DSA uses to separate switch ports.
But currently these have no global significance - they are simply an
ordered list of DSA_MAX_SWITCHES x DSA_MAX_PORTS numbers ending at 4095.
The reason why this is submitted as a fix is that the existing mapping
of VIDs should not enter into a stable kernel, so we can pretend that
only the new format exists. This way tcpdump won't need to try to make
something out of the VLAN tags on 5.2 kernels.
Fixes: f9bbe4477c30 ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 802.1Q tagging performs an unbalanced setup in terms of RX VIDs on
the CPU port. For the ingress path of a 802.1Q switch to work, the RX
VID of a port needs to be seen as tagged egress on the CPU port.
While configuring the other front-panel ports to be part of this VID,
for bridge scenarios, the untagged flag is applied even on the CPU port
in dsa_switch_vlan_add. This happens because DSA applies the same flags
on the CPU port as on the (bridge-controlled) slave ports, and the
effect in this case is that the CPU port tagged settings get deleted.
Instead of fixing DSA by introducing a way to control VLAN flags on the
CPU port (and hence stop inheriting from the slave ports) - a hard,
perhaps intractable problem - avoid this situation by moving the setup
part of the RX VID on the CPU port after all the other front-panel ports
have been added to the VID.
Fixes: f9bbe4477c30 ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sk_buff control block can have any contents on xmit put there by the
stack, so initialization is mandatory, since we are checking its value
after the actual DSA xmit (the tagger may have changed it).
The DSA_SKB_ZERO() macro could have been used for this purpose, but:
- Zeroizing a 48-byte memory region in the hotpath is best avoided.
- It would have triggered a warning with newer compilers since
__dsa_skb_cb contains a structure within a structure, and the {0}
initializer was incorrect for that purpose.
So simply remove the DSA_SKB_ZERO() macro and initialize the
deferred_xmit variable by hand (which should be done for all further
dsa_skb_cb variables which need initialization - currently none - to
avoid the performance penalty).
Fixes: 97a69a0dea9a ("net: dsa: Add support for deferred xmit")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix gcc build error:
net/dsa/tag_brcm.c:211:16: error: brcm_prepend_netdev_ops undeclared here (not in a function); did you mean brcm_netdev_ops?
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
^
./include/net/dsa.h:708:10: note: in definition of macro DSA_TAG_DRIVER
.ops = &__ops, \
^~~~~
./include/net/dsa.h:701:36: warning: dsa_tag_driver_brcm_prepend_netdev_ops defined but not used [-Wunused-variable]
#define DSA_TAG_DRIVER_NAME(__ops) dsa_tag_driver ## _ ## __ops
^
./include/net/dsa.h:707:30: note: in expansion of macro DSA_TAG_DRIVER_NAME
static struct dsa_tag_driver DSA_TAG_DRIVER_NAME(__ops) = { \
^~~~~~~~~~~~~~~~~~~
net/dsa/tag_brcm.c:211:1: note: in expansion of macro DSA_TAG_DRIVER
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
Like the CONFIG_NET_DSA_TAG_BRCM case,
brcm_prepend_netdev_ops and DSA_TAG_PROTO_BRCM_PREPEND
should be wrappeed by CONFIG_NET_DSA_TAG_BRCM_PREPEND.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b74b70c44986 ("net: dsa: Support prepended Broadcom tag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor conflict with the DSA legacy code removal.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BUG: unable to handle kernel paging request at ffffffffa01c5430
PGD 3270067 P4D 3270067 PUD 3271063 PMD 230bc5067 PTE 0
Oops: 0000 [#1
CPU: 0 PID: 6159 Comm: modprobe Not tainted 5.1.0+ #33
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:raw_notifier_chain_register+0x16/0x40
Code: 63 f8 66 90 e9 5d ff ff ff 90 90 90 90 90 90 90 90 90 90 90 55 48 8b 07 48 89 e5 48 85 c0 74 1c 8b 56 10 3b 50 10 7e 07 eb 12 <39> 50 10 7c 0d 48 8d 78 08 48 8b 40 08 48 85 c0 75 ee 48 89 46 08
RSP: 0018:ffffc90001c33c08 EFLAGS: 00010282
RAX: ffffffffa01c5420 RBX: ffffffffa01db420 RCX: 4fcef45928070a8b
RDX: 0000000000000000 RSI: ffffffffa01db420 RDI: ffffffffa01b0068
RBP: ffffc90001c33c08 R08: 000000003e0a33d0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000094443661 R12: ffff88822c320700
R13: ffff88823109be80 R14: 0000000000000000 R15: ffffc90001c33e78
FS: 00007fab8bd08540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa01c5430 CR3: 00000002297ea000 CR4: 00000000000006f0
Call Trace:
register_netdevice_notifier+0x43/0x250
? 0xffffffffa01e0000
dsa_slave_register_notifier+0x13/0x70 [dsa_core
? 0xffffffffa01e0000
dsa_init_module+0x2e/0x1000 [dsa_core
do_one_initcall+0x6c/0x3cc
? do_init_module+0x22/0x1f1
? rcu_read_lock_sched_held+0x97/0xb0
? kmem_cache_alloc_trace+0x325/0x3b0
do_init_module+0x5b/0x1f1
load_module+0x1db1/0x2690
? m_show+0x1d0/0x1d0
__do_sys_finit_module+0xc5/0xd0
__x64_sys_finit_module+0x15/0x20
do_syscall_64+0x6b/0x1d0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Cleanup allocated resourses if there are errors,
otherwise it will trgger memleak.
Fixes: c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().
The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.
However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.
Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.
This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.
The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).
One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.
There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).
Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>-
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if VLAN filtering is global, DSA will call this callback once per
each port. Drivers should not have to compare the global state with the
requested change. So let DSA do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ports are standalone (after they left the bridge), they should have
no VLAN filtering semantics (they should pass all traffic to the CPU).
Currently this is not true for switchdev drivers, because the bridge
"forgets" to unset that.
Normally one would think that doing this at the bridge layer would be a
better idea, i.e. call br_vlan_filter_toggle() from br_del_if(), similar
to how nbp_vlan_init() is called from br_add_if().
However what complicates that approach, and makes this one preferable,
is the fact that for the bridge core, vlan_filtering is a per-bridge
setting, whereas for switchdev/DSA it is per-port. Also there are
switches where the setting is per the entire device, and unsetting
vlan_filtering one by one, for each leaving port, would not be possible
from the bridge core without a certain level of awareness. So do this in
DSA and let drivers be unaware of it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the CONFIG symbols tristate and add help text.
The broadcom and Microchip KSZ tag drivers support two different
tagging protocols in one driver. Add a configuration option for the
drivers, and then options to select the protocol.
Create a submenu for the tagging drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
tab/space cleanup
Help text wording
NET_DSA_TAG_BRCM_COMMON and NET_DSA_TAG_KZS_COMMON hidden
v3:
More tabification
Punctuation
v4:
trailler->trailer
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible that the driver is compiled with both
CONFIG_NET_DSA_TAG_BRCM and CONFIG_NET_DSA_TAG_BRCM_PREPEND disabled.
This results in warnings about unused symbols. Add some conditional
compilation to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Reorder patch to before tag drivers can be modules
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the _get and _put functions to make use of the list of tag
drivers. Also, trigger the loading of the module, based on the alias
information. The _get function takes a reference on the tag driver, so
it cannot be unloaded, and the _put function releases the reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Make tag_driver_register void
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a DSA switch driver is unloaded, the lock on the tag driver
should be released so the module can be unloaded. Add the needed calls,
but leave the actual release code as a stub.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dsa_resolve_tag_protocol() is used to find the tagging driver needed
by a switch driver. When the tagging drivers become modules, it will
be necassary to take a reference on the module to prevent it being
unloaded. So rename this function to _get() to indicate it has some
locking properties.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The none tagger is special in that it does not live in a tag_*.c file,
but is within the core. Register/unregister when DSA is
loaded/unloaded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the tag drivers register themselves with the DSA core, keeping
them in a linked list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the tag drivers are some variant of GPL. Add a MODULE_LICENSE()
indicating this, so the drivers can later be compiled as modules.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the tag drivers become modules, we will need to dynamically load
them based on what the switch drivers need. Add aliases to map between
the TAG protocol and the driver.
In order to do this, we need the tag protocol number as something
which the C pre-processor can stringinfy. Only the compiler knows the
value of an enum, CPP cannot use them. So add #defines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an SPDX header, and remove the license boilerplate text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get(). Leave
ndo_get_port_parent_id implementation only for legacy.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flow_dissect for qca tagged packet to get the right hash.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since each non-legacy slave has its own devlink port instance
correctly set, rely on devlink core to generate correct phys port name.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for devlink compat functions to work, implement
ndo_get_devlink_port. Legacy slaves does not have devlink port instances
created for themselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When phylink_of_phy_connect fails, dsa_slave_phy_setup tries to save the
day by connecting to an alternative PHY, none other than a PHY on the
switch's internal MDIO bus, at an address equal to the port's index.
However this does not take into consideration the scenario when the
switch that failed to probe an external PHY does not have an internal
MDIO bus at all.
Fixes: aab9c4067d23 ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
