aboutsummaryrefslogtreecommitdiff
path: root/net/mac80211/ieee80211_i.h
AgeCommit message (Collapse)Author
2019-11-22mac80211: Implement Airtime-based Queue Limit (AQL)Kan Yan
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate effectively to control excessive queueing latency, the CoDel algorithm requires an accurate measure of how long packets stays in the queue, AKA sojourn time. The sojourn time measured at the mac80211 layer doesn't include queueing latency in the lower layer (firmware/hardware) and CoDel expects lower layer to have a short queue. However, most 802.11ac chipsets offload tasks such TX aggregation to firmware or hardware, thus have a deep lower layer queue. Without a mechanism to control the lower layer queue size, packets only stay in mac80211 layer transiently before being sent to firmware queue. As a result, the sojourn time measured by CoDel in the mac80211 layer is almost always lower than the CoDel latency target, hence CoDel does little to control the latency, even when the lower layer queue causes excessive latency. The Byte Queue Limits (BQL) mechanism is commonly used to address the similar issue with wired network interface. However, this method cannot be applied directly to the wireless network interface. "Bytes" is not a suitable measure of queue depth in the wireless network, as the data rate can vary dramatically from station to station in the same network, from a few Mbps to over Gbps. This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work effectively with wireless drivers that utilized firmware/hardware offloading. AQL allows each txq to release just enough packets to the lower layer to form 1-2 large aggregations to keep hardware fully utilized and retains the rest of the frames in mac80211 layer to be controlled by the CoDel algorithm. Signed-off-by: Kan Yan <kyan@google.com> [ Toke: Keep API to set pending airtime internal, fix nits in commit msg ] Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-11-22mac80211: Import airtime calculation code from mt76Toke Høiland-Jørgensen
Felix recently added code to calculate airtime of packets to the mt76 driver. Import this into mac80211 so we can use it for airtime queue limit calculations. The airtime.c file is copied verbatim from the mt76 driver, and adjusted to be usable in mac80211. This involves: - Switching to mac80211 data structures. - Adding support for 160 MHz channels and HE mode. - Moving the symbol and duration calculations around a bit to avoid rounding with the higher rates and longer symbol times used for HE rates. The per-rate TX rate calculation is also split out to its own function so it can be used directly for the AQL calculations later. Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com [fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-09-11mac80211: IBSS: send deauth when expiring inactive STAsJohannes Berg
When we expire an inactive station, try to send it a deauth. This helps if it's actually still around, and just has issues with beacon distribution (or we do), and it will not also remove us. Then, if we have shared state, this may not be reset properly, causing problems; for example, we saw a case where aggregation sessions weren't removed properly (due to the TX start being offloaded to firmware and it relying on deauth for stop), causing a lot of traffic to get lost due to the SN reset after remove/add of the peer. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20190830112451.21655-9-luca@coelho.fi Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-31mac80211: allow setting spatial reuse parameters from bss_confJohn Crispin
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or when a station connects to an AP. This allows the driver to configure the HW accordingly. Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-29mac80211: add support for the ADDBA extension elementJohn Crispin
HE allows peers to negotiate the aggregation fragmentation level to be used during transmission. The level can be 1-3. The Ext element is added behind the ADDBA request inside the action frame. The responder will then reply with the same level or a lower one if the requested one is not supported. This patch only handles the negotiation part as the ADDBA frames get passed to the ATH11k firmware, which does the rest of the magic for us aswell as generating the requests. Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com> Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20190729104512.27615-1-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-29mac80211: propagate HE operation info into bss_confJohn Crispin
Upon a successful assoc a station shall store the content of the HE operation element inside bss_conf so that the driver can setup the hardware accordingly. Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20190729102342.8659-2-john@phrozen.org [use struct copy] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-26mac80211: implement HE support for meshSven Eckelmann
Implement the basics required for supporting high efficiency with mesh: include HE information elements in beacons, probe responses, and peering action frames, and check for compatible HE configurations when peering. Signed-off-by: Sven Eckelmann <seckelmann@datto.com> Forwarded: https://patchwork.kernel.org/patch/11029299/ Link: https://lore.kernel.org/r/20190724163359.3507-2-sven@narfation.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-26mac80211: HE: add Spatial Reuse element parsing supportJohn Crispin
Add support to mac80211 for parsing SPR elements as per P802.11ax_D4.0 section 9.4.2.241. Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com> Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20190618061915.7102-2-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-26mac80211: propagate struct ieee80211_tx_status into ieee80211_tx_monitor()John Crispin
This will allow use to report HE rates on the radiotap interface. Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20190714154419.11854-3-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-26mac80211: add support for parsing ADDBA_EXT IEsJohn Crispin
ADDBA_EXT IEs can be used to negotiate the BA fragmentation level. Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20190713163642.18491-2-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-08Merge branch 'linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto updates from Herbert Xu: "Here is the crypto update for 5.3: API: - Test shash interface directly in testmgr - cra_driver_name is now mandatory Algorithms: - Replace arc4 crypto_cipher with library helper - Implement 5 way interleave for ECB, CBC and CTR on arm64 - Add xxhash - Add continuous self-test on noise source to drbg - Update jitter RNG Drivers: - Add support for SHA204A random number generator - Add support for 7211 in iproc-rng200 - Fix fuzz test failures in inside-secure - Fix fuzz test failures in talitos - Fix fuzz test failures in qat" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits) crypto: stm32/hash - remove interruptible condition for dma crypto: stm32/hash - Fix hmac issue more than 256 bytes crypto: stm32/crc32 - rename driver file crypto: amcc - remove memset after dma_alloc_coherent crypto: ccp - Switch to SPDX license identifiers crypto: ccp - Validate the the error value used to index error messages crypto: doc - Fix formatting of new crypto engine content crypto: doc - Add parameter documentation crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR crypto: arm64/aes-ce - add 5 way interleave routines crypto: talitos - drop icv_ool crypto: talitos - fix hash on SEC1. crypto: talitos - move struct talitos_edesc into talitos.h lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE crypto/NX: Set receive window credits to max number of CRBs in RxFIFO crypto: asymmetric_keys - select CRYPTO_HASH where needed crypto: serpent - mark __serpent_setkey_sbox noinline crypto: testmgr - dynamically allocate crypto_shash crypto: testmgr - dynamically allocate testvec_config crypto: talitos - eliminate unneeded 'done' functions at build time ...
2019-06-21Merge tag 'spdx-5.2-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx Pull still more SPDX updates from Greg KH: "Another round of SPDX updates for 5.2-rc6 Here is what I am guessing is going to be the last "big" SPDX update for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that were "easy" to determine by pattern matching. The ones after this are going to be a bit more difficult and the people on the spdx list will be discussing them on a case-by-case basis now. Another 5000+ files are fixed up, so our overall totals are: Files checked: 64545 Files with SPDX: 45529 Compared to the 5.1 kernel which was: Files checked: 63848 Files with SPDX: 22576 This is a huge improvement. Also, we deleted another 20000 lines of boilerplate license crud, always nice to see in a diffstat" * tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits) treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485 ...
2019-06-20net/mac80211: move WEP handling to ARC4 library interfaceArd Biesheuvel
The WEP code in the mac80211 subsystem currently uses the crypto API to access the arc4 (RC4) cipher, which is overly complicated, and doesn't really have an upside in this particular case, since ciphers are always synchronous and therefore always implemented in software. Given that we have no accelerated software implementations either, it is much more straightforward to invoke a generic library interface directly. Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-14mac80211: do not start any work during reconfigure flowNaftali Goldstein
It is not a good idea to try to perform any work (e.g. send an auth frame) during reconfigure flow. Prevent this from happening, and at the end of the reconfigure flow requeue all the works. Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-06-14mac80211: only warn once on chanctx_conf being NULLYibo Zhao
In multiple SSID cases, it takes time to prepare every AP interface to be ready in initializing phase. If a sta already knows everything it needs to join one of the APs and sends authentication to the AP which is not fully prepared at this point of time, AP's channel context could be NULL. As a result, warning message occurs. Even worse, if the AP is under attack via tools such as MDK3 and massive authentication requests are received in a very short time, console will be hung due to kernel warning messages. WARN_ON_ONCE() could be a better way for indicating warning messages without duplicate messages to flood the console. Johannes: We still need to address the underlying problem, but we don't really have a good handle on it yet. Suppress the worst side-effects for now. Signed-off-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Yibo Zhao <yiboz@codeaurora.org> [johannes: add note, change subject] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-05-24mac80211: handle deauthentication/disassociation from TDLS peerYu Wang
When receiving a deauthentication/disassociation frame from a TDLS peer, a station should not disconnect the current AP, but only disable the current TDLS link if it's enabled. Without this change, a TDLS issue can be reproduced by following the steps as below: 1. STA-1 and STA-2 are connected to AP, bidirection traffic is running between STA-1 and STA-2. 2. Set up TDLS link between STA-1 and STA-2, stay for a while, then teardown TDLS link. 3. Repeat step #2 and monitor the connection between STA and AP. During the test, one STA may send a deauthentication/disassociation frame to another, after TDLS teardown, with reason code 6/7, which means: Class 2/3 frame received from nonassociated STA. On receive this frame, the receiver STA will disconnect the current AP and then reconnect. It's not a expected behavior, purpose of this frame should be disabling the TDLS link, not the link with AP. Cc: stable@vger.kernel.org Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-04-26mac80211: probe unexercised mesh linksRajkumar Manoharan
The requirement for mesh link metric refreshing, is that from one mesh point we be able to send some data frames to other mesh points which are not currently selected as a primary traffic path, but which are only 1 hop away. The absence of the primary path to the chosen node makes it necessary to apply some form of marking on a chosen packet stream so that the packets can be properly steered to the selected node for testing, and not by the regular mesh path lookup. Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-04-26mac80211: add option for setting control flagsRajkumar Manoharan
Allows setting of control flags of skb cb - if needed - when calling ieee80211_subif_start_xmit(). Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-04-26mac80211: debugfs option to force TX status framesJulius Niedworok
At Technical University of Munich we use MAC 802.11 TX status frames to perform several measurements in MAC 802.11 setups. With ath based drivers this was possible until commit d94a461d7a7df6 ("ath9k: use ieee80211_tx_status_noskb where possible") as the driver ignored the IEEE80211_TX_CTL_REQ_TX_STATUS flag and always delivered tx_status frames. Since that commit, this behavior was changed and the driver now adheres to IEEE80211_TX_CTL_REQ_TX_STATUS. Due to performance reasons, IEEE80211_TX_CTL_REQ_TX_STATUS is not set for data frames from interfaces in managed mode. Hence, frames that are sent from a managed mode interface do never deliver tx_status frames. This remains true even if a monitor mode interface (the measurement interface) is added to the same ieee80211 physical device. Thus, there is no possibility for receiving tx_status frames for frames sent on an interface in managed mode, if the driver adheres to IEEE80211_TX_CTL_REQ_TX_STATUS. In order to force delivery of tx_status frames for research and debugging purposes, implement a debugfs option force_tx_status for ieee80211 physical devices. When this option is set for a physical device, IEEE80211_TX_CTL_REQ_TX_STATUS is enabled in all packets sent from that device. This option can be set via /sys/kernel/debug/ieee80211/<dev>/force_tx_status. The default is disabled. Co-developed-by: Charlie Groh <ga58taw@mytum.de> Signed-off-by: Charlie Groh <ga58taw@mytum.de> Signed-off-by: Julius Niedworok <julius.n@gmx.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-04-26mac80211: IEEE 802.11 Extended Key ID supportAlexander Wetzel
Add support for Extended Key ID as defined in IEEE 802.11-2016. - Implement the nl80211 API for Extended Key ID - Extend mac80211 API to allow drivers to support Extended Key ID - Enable Extended Key ID by default for drivers only supporting SW crypto (e.g. mac80211_hwsim) - Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX) - Select the decryption key based on the MPDU keyid - Enforce existing assumptions in the code that rekeys don't change the cipher Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de> [remove module parameter] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-04-26mac80211: support profile split between elementsSara Sharon
Since an element is limited to 255 octets, a profile may be split split to several elements. Support the split as defined in the 11ax draft 3. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-22mac80211: support max channel switch time elementSara Sharon
2018 REVmd of the spec introduces the max channel switch time element which is optionally included in beacons/probes when there is a channel switch / extended channel switch element. The value represents the maximum delay between the time the AP transmitted the last beacon in current channel and the expected time of the first beacon in the new channel, in TU. Parse the value and pass it to the driver. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-22cfg80211: Report Association Request frame IEs in association eventsJouni Malinen
This extends the NL80211_CMD_ASSOCIATE event case to report NL80211_ATTR_REQ_IE similarly to what is already done with the NL80211_CMD_CONNECT events if the driver provides this information. In practice, this adds (Re)Association Request frame information element reporting to mac80211 drivers for the cases where user space SME is used. This provides more information for user space to figure out which capabilities were negotiated for the association. For example, this can be used to determine whether HT, VHT, or HE is used. Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-08mac80211: support multi-bssidSara Sharon
Add support for multi-bssid. This includes: - Parsing multi-bssid element - Overriding DTIM values - Taking into account in various places the inner BSSID instead of transmitter BSSID - Save aside some multi-bssid properties needed by drivers Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-08mac80211: pass bssids to elements parsing functionSara Sharon
In multiple BSSID, we have nested IEs inside the multiple BSSID IE, that override the external ones for that specific BSS. As preparation for supporting that, pass 2 BSSIDs to the parse function, the transmitter, and the selected BSSID, so it can know which IEs to choose. If the selected BSSID is NULL, the outer ones will be applied. Change ieee80211_bss_info_update to parse elements itself, instead of receiving them parsed, so we have the relevant bss entry in hand. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-19mac80211: Add airtime accounting and scheduling to TXQsToke Høiland-Jørgensen
This adds airtime accounting and scheduling to the mac80211 TXQ scheduler. A new callback, ieee80211_sta_register_airtime(), is added that drivers can call to report airtime usage for stations. When airtime information is present, mac80211 will schedule TXQs (through ieee80211_next_txq()) in a way that enforces airtime fairness between active stations. This scheduling works the same way as the ath9k in-driver airtime fairness scheduling. If no airtime usage is reported by the driver, the scheduler will default to round-robin scheduling. For drivers that don't control TXQ scheduling in software, a new API function, ieee80211_txq_may_transmit(), is added which the driver can use to check if the TXQ is eligible for transmission, or should be throttled to enforce fairness. Calls to this function must also be enclosed in ieee80211_txq_schedule_{start,end}() calls to ensure proper locking. The API ieee80211_txq_may_transmit() also ensures that TXQ list will be aligned aginst driver's own round-robin scheduler list. i.e it rotates the TXQ list till it makes the requested node becomes the first entry in TXQ list. Thus both the TXQ list and driver's list are in sync. Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by: Louie Lu <git@louie.lu> [added debugfs write op to reset airtime counter] Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-19mac80211: Add TXQ scheduling APIToke Høiland-Jørgensen
This adds an API to mac80211 to handle scheduling of TXQs. The interface between driver and mac80211 for TXQ handling is changed by adding two new functions: ieee80211_next_txq(), which will return the next TXQ to schedule in the current round-robin rotation, and ieee80211_return_txq(), which the driver uses to indicate that it has finished scheduling a TXQ (which will then be put back in the scheduling rotation if it isn't empty). The driver must call ieee80211_txq_schedule_start() at the start of each scheduling session, and ieee80211_txq_schedule_end() at the end. The API then guarantees that the same TXQ is not returned twice in the same session (so a driver can loop on ieee80211_next_txq() without worrying about breaking the loop. Usage of the new API is optional, so drivers can be ported one at a time. In this patch, the actual scheduling performed by mac80211 is simple round-robin, but a subsequent commit adds airtime fairness awareness to the scheduler. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> [minor kernel-doc fix, propagate sparse locking checks out] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-12-18mac80211: update driver when MU EDCA params changeShaul Triebitz
Similar to WMM IE, if MU_EDCA IE parameters changed (or ceased to exist) tell the Driver about it. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11mac80211: Extend SAE authentication in infra BSS STA modeJouni Malinen
Previous implementation of SAE authentication in infrastructure BSS was somewhat restricting and not exactly clean way of handling the two auth() operations. This ended up removing and re-adding the STA entry for the AP in the middle of authentication and also messing up authentication state tracking through the sequence of four Authentication frames. Furthermore, this did not work if the AP ended up sending out SAE Confirm (auth trans #2) immediately after SAE Commit (auth trans #1) before the station had time to transmit its SAE Confirm. Clean up authentication state handling for the SAE case to allow two rounds of auth() calls without dropping all state between those operations. Track peer Confirmed status and mark authentication completed only once both ends have confirmed. ieee80211_mgd_auth() check for EBUSY cases is now handling only the pending association (ifmgd->assoc_data) while all pending authentication (ifmgd->auth_data) cases are allowed to proceed to allow user space to start a new connection attempt from scratch even if the previously requested authentication is still waiting completion. This is needed to avoid making SAE error cases with retries take excessive amount of time with no means for the user space to stop that (apart from setting the netdev down). As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing SAE authentication since the new ieee80211_mark_sta_auth() helper function can handle both completion of authentication and updates to the STA entry under the same condition and there is no need to return from the function between those operations. Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-09-05mac80211: add ability to parse CCFS2Johannes Berg
With newer VHT implementations, it's necessary to look at the HT operation's CCFS2 field to identify the actual bandwidth used. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-09-05mac80211: introduce capability flags for VHT EXT NSS supportJohannes Berg
Depending on whether or not rate control supports selecting rates depending on the bandwidth, we can use VHT extended NSS support. In essence, this is dot11VHTExtendedNSSBWCapable from the spec, since depending on that we'll need to parse the bandwidth. If needed, also set/clear the VHT Capability Element bit for this capability so that we don't advertise it erroneously or don't advertise it when we actually use it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28mac80211: add stop/start logic for software TXQsManikanta Pubbisetty
Sometimes, it is required to stop the transmissions momentarily and resume it later; stopping the txqs becomes very critical in scenarios where the packet transmission has to be ceased completely. For example, during the hardware restart, during off channel operations, when initiating CSA(upon detecting a radar on the DFS channel), etc. The TX queue stop/start logic in mac80211 works well in stopping the TX when drivers make use of netdev queues, i.e, when Qdiscs in network layer take care of traffic scheduling. Since the devices implementing wake_tx_queue can run without Qdiscs, packets will be handed to mac80211 directly without queueing them in the netdev queues. Also, mac80211 does not invoke any of the netif_stop_*/netif_wake_* APIs if wake_tx_queue is implemented. Since the queues are not stopped in this case, transmissions can continue and this will impact negatively on the operation of the wireless device. For example, During hardware restart, we stop the netdev queues so that packets are not sent to the driver. Since ath10k implements wake_tx_queue, TX queues will not be stopped and packets might reach the hardware while it is restarting; this can make hardware unresponsive and the only possible option for recovery is to reboot the entire system. There is another problem to this, it is observed that the packets were sent on the DFS channel for a prolonged duration after radar detection impacting the channel closing time. We can still invoke netif stop/wake APIs when wake_tx_queue is implemented but this could lead to packet drops in network layer; adding stop/start logic for software TXQs in mac80211 instead makes more sense; the change proposed adds the same in mac80211. Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-06-18mac80211: add support for HELuca Coelho
Add support for HE in mac80211 conforming with P802.11ax_D1.4. Johannes: Fix another bug with the buf_size comparison in agg-rx.c. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Ido Yariv <idox.yariv@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-06-15mac80211: support scan features for improved scan privacyJohannes Berg
Support the new random SN and minimal probe request contents scan flags for the case of software scan - for hardware scan the drivers need to opt in, but may need to do only that, depending on their implementation. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2018-06-15mac80211: split ieee80211_send_probe_req()Johannes Berg
This function is passed many more parameters in the scan case than in the MLME case, and differentiates the two cases inside. Split it up and make both versions static to simplify things. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2018-06-15mac80211: add probe request building flagsJohannes Berg
Add flags to pass through to probe request building and change the "bool directed" to be one of them. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2018-05-08mac80211: Support the new cfg80211 TXQ stats APIToke Høiland-Jørgensen
This adds support to mac80211 to export TXQ stats via the newly added cfg80211 API. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29mac80211: Send control port frames over nl80211Denis Kenzior
If userspace requested control port frames to go over 80211, then do so. The control packets are intercepted just prior to delivery of the packet to the underlying network device. Pre-authentication type frames (protocol: 0x88c7) are also forwarded over nl80211. Signed-off-by: Denis Kenzior <denkenz@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29mac80211: Add support for tx_control_portDenis Kenzior
Signed-off-by: Denis Kenzior <denkenz@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29mac80211: limit wmm params to comply with ETSI requirementsHaim Dreyfuss
ETSI has recently added new requirements that restrict the WMM parameter values for 5GHz frequencies. We need to take care of the following scenarios in order to comply with these new requirements: 1. When using mac80211 default values; 2. When the userspace tries to configure its own values; 3. When associating to an AP which advertises WWM IE. When associating to an AP, the client uses the values in the advertised WMM IE. But the AP may not comply with the new ETSI requirements, so the client needs to check the current regulatory rules and use those limits accordingly. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29mac80211: Use proper chan_width enum in sta opmode eventtamizhr@codeaurora.org
Bandwidth change value reported via nl80211 contains mac80211 specific enum value(ieee80211_sta_rx_bw) and which is not understand by userspace application. Map the mac80211 specific value to nl80211_chan_width enum value to avoid using wrong value in the userspace application. And used station's ht/vht capability to map IEEE80211_STA_RX_BW_20 and IEEE80211_STA_RX_BW_160 with proper nl80211 value. Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-03-29mac80211: Use proper smps_mode enum in sta opmode eventtamizhr@codeaurora.org
SMPS_MODE change value notified via nl80211 contains mac80211 specific value(ieee80211_smps_mode) and user space application will not know those values. This patch add support to map the mac80211 enum value to nl80211_smps_mode which will be understood by the userspace application. Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-02-22Merge tag 'mac80211-for-davem-2018-02-22' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Various fixes across the tree, the shortlog basically says it all: cfg80211: fix cfg80211_beacon_dup -> old bug in this code cfg80211: clear wep keys after disconnection -> certain ways of disconnecting left the keys mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4 -> alignment issues with using 14 bytes mac80211: Do not disconnect on invalid operating class -> if the AP has a bogus operating class, let it be mac80211: Fix sending ADDBA response for an ongoing session -> don't send the same frame twice cfg80211: use only 1Mbps for basic rates in mesh -> interop issue with old versions of our code mac80211_hwsim: don't use WQ_MEM_RECLAIM -> it causes splats because it flushes work on a non-reclaim WQ regulatory: add NUL to request alpha2 -> nla_put_string() issue from Kees mac80211: mesh: fix wrong mesh TTL offset calculation -> protocol issue mac80211: fix a possible leak of station stats -> error path might leak memory mac80211: fix calling sleeping function in atomic context -> percpu allocations need to be made with gfp flags ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-31mac80211: mesh: fix wrong mesh TTL offset calculationPeter Oh
mesh TTL offset in Mesh Channel Switch Parameters element depends on not only Secondary Channel Offset element, but also affected by HT Control field and Wide Bandwidth Channel Switch element. So use element structure to manipulate mesh channel swich param IE after removing its constant attribution to correct the miscalculation. Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-19Revert "mac80211: Add TXQ scheduling API"Johannes Berg
This reverts commit e937b8da5a591f141fe41aa48a2e898df9888c95. Turns out that a new driver (mt76) is coming in through Kalle's tree, and will conflict with this. It also has some conflicting requirements, so we'll revisit this later. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-19Revert "mac80211: Add airtime account and scheduling to TXQs"Johannes Berg
This reverts commit b0d52ad821843a6c5badebd80feef9f871904fa6. We need to revert the TXQ scheduling API due to conflicts with a new driver, and this depends on that API. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-11mac80211: Add airtime account and scheduling to TXQsToke Høiland-Jørgensen
This adds airtime accounting and scheduling to the mac80211 TXQ scheduler. A new hardware flag, AIRTIME_ACCOUNTING, is added that drivers can set if they support reporting airtime usage of transmissions. When this flag is set, mac80211 will expect the actual airtime usage to be reported in the tx_time and rx_time fields of the respective status structs. When airtime information is present, mac80211 will schedule TXQs (through ieee80211_next_txq()) in a way that enforces airtime fairness between active stations. This scheduling works the same way as the ath9k in-driver airtime fairness scheduling. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-11mac80211: Add TXQ scheduling APIToke Høiland-Jørgensen
This adds an API to mac80211 to handle scheduling of TXQs and changes the interface between driver and mac80211 for TXQ handling as follows: - The wake_tx_queue callback interface no longer includes the TXQ. Instead, the driver is expected to retrieve that from ieee80211_next_txq() - Two new mac80211 functions are added: ieee80211_next_txq() and ieee80211_schedule_txq(). The former returns the next TXQ that should be scheduled, and is how the driver gets a queue to pull packets from. The latter is called internally by mac80211 to start scheduling a queue, and the driver is supposed to call it to re-schedule the TXQ after it is finished pulling packets from it (unless the queue emptied). The ath9k and ath10k drivers are changed to use the new API. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-11mac80211: make __ieee80211_start_rx_ba_session staticJohannes Berg
The function is only used with the file, so make it static. Signed-off-by: Johannes Berg <johannes.berg@intel.com>