aboutsummaryrefslogtreecommitdiff
path: root/net/mac80211/util.c
AgeCommit message (Collapse)Author
2022-03-11mac80211: Add support to trigger sta disconnect on hardware restartYoughandhar Chintala
Currently in case of target hardware restart, we just reconfig and re-enable the security keys and enable the network queues to start data traffic back from where it was interrupted. Many ath10k wifi chipsets have sequence numbers for the data packets assigned by firmware and the mac sequence number will restart from zero after target hardware restart leading to mismatch in the sequence number expected by the remote peer vs the sequence number of the frame sent by the target firmware. This mismatch in sequence number will cause out-of-order packets on the remote peer and all the frames sent by the device are dropped until we reach the sequence number which was sent before we restarted the target hardware In order to fix this, we trigger a sta disconnect, in case of target hw restart. After this there will be a fresh connection and thereby avoiding the dropping of frames by remote peer. The right fix would be to pull the entire data path into the host which is not feasible or would need lots of complex changes and will still be inefficient. Tested on ath10k using WCN3990, QCA6174 Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org> Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Add EHT capabilities to association/probe requestIlan Peer
Add the EHT capabilities element to both probe request and association request frames, if advertised by the driver. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.2ec94388acee.I40d2ef06099cb091e9c2c01f8ef521b993a3d559@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Add initial support for EHT and 320 MHz channelsIlan Peer
Add initial support for EHT and 320 MHz bandwidth in mac80211. As a new IEEE80211_STA_RX_BW_320 is added to enum ieee80211_sta_rx_bandwidth, update the drivers to avoid compilation warnings. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.0f144cc0bba6.Iad18111264da87eed5fd7b017f0cc6e58c604e07@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Support parsing EHT elementsIlan Peer
Parse the new EHT elements in the element parsing utilities. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.4d52ddaf1af4.Ib6beb1aa85e25b71ce40d3260b2e5b117cc42308@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: parse only HE capability elements with valid sizeJohannes Berg
The code validates the HE capability element size later, but slightly wrong, so use the new helper to do it right and only accept it if it has a good size. Link: https://lore.kernel.org/r/20220214172920.b5b06f264a61.I645ac1e2dc0ace223ef3e551cd5a71c88bd55e04@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-04mac80211: Remove redundent assignment channel_typeJiapeng Chong
Fix the following coccicheck warnings: net/mac80211/util.c:3265:3: warning: Value stored to 'channel_type' is never read [clang-analyzer-deadcode.DeadStores]. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Link: https://lore.kernel.org/r/20220113161557.129427-1-jiapeng.chong@linux.alibaba.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-04mac80211: limit bandwidth in HE capabilitiesJohannes Berg
If we're limiting bandwidth for some reason such as regulatory restrictions, then advertise that limitation just like we do for VHT today, so the AP is aware we cannot use the higher BW it might be using. Fixes: 41cbb0f5a295 ("mac80211: add support for HE") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20220202104617.70c8e3e7ee76.If317630de69ff1146bec7d47f5b83038695eb71d@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-01-04mac80211: Add stations iterator where the iterator function may sleepMartin Blumenstingl
ieee80211_iterate_active_interfaces() and ieee80211_iterate_active_interfaces_atomic() already exist, where the former allows the iterator function to sleep. Add ieee80211_iterate_stations() which is similar to ieee80211_iterate_stations_atomic() but allows the iterator to sleep. This is needed for adding SDIO support to the rtw88 driver. Some interators there are reading or writing registers. With the SDIO ops (sdio_readb, sdio_writeb and friends) this means that the iterator function may sleep. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20211228211501.468981-2-martin.blumenstingl@googlemail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-12-14mac80211: do drv_reconfig_complete() before restarting allJohannes Berg
When we reconfigure, the driver might do some things to complete the reconfiguration. It's strange and could be broken in some cases because we restart other works (e.g. remain-on-channel and TX) before this happens, yet only start queues later. Change this to do the reconfig complete when reconfiguration is actually complete, not when we've already started doing other things again. For iwlwifi, this should fix a race where the reconfig can race with TX, for ath10k and ath11k that also use this it won't make a difference because they just start queues there, and mac80211 also stopped the queues and will restart them later as before. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cab99f22fe19.Iefe494687f15fd85f77c1b989d1149c8efdfdc36@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-12-14mac80211: Fix the size used for building probe requestIlan Peer
Instead of using the hard-coded value of '100' use the correct scan IEs length as calculated during HW registration to mac80211. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20211129152938.0a82d6891719.I8ded1f2e0bccb9e71222c945666bcd86537f2e35@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-12-14mac80211: validate extended element ID is presentJohannes Berg
Before attempting to parse an extended element, verify that the extended element ID is present. Fixes: 41cbb0f5a295 ("mac80211: add support for HE") Reported-by: syzbot+59bdff68edce82e393b6@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20211211201023.f30a1b128c07.I5cacc176da94ba316877c6e10fe3ceec8b4dbd7d@changeid Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-11-15mac80211: fix monitor_sdata RCU/locking assertionsJohannes Berg
Since commit a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") we've not only been protecting the pointer to monitor_sdata with the RTNL, but also with the wiphy->mtx. This is relevant in a number of lockdep assertions, e.g. the one we hit in ieee80211_set_monitor_channel(). However, we're now protecting all the assignments/dereferences, even the one in interface iter, with the wiphy->mtx, so switch over the lockdep assertions to that lock. Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20211112135143.cb8e8ceffef3.Iaa210f16f6904c8a7a24954fb3396da0ef86ec08@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-09-27mac80211: add parse regulatory info in 6 GHz operation informationWen Gong
This patch is to convert the regulatory info subfield in HE operation element to power type and save in struct cfg80211_chan_def. Signed-off-by: Wen Gong <wgong@codeaurora.org> Link: https://lore.kernel.org/r/20210924100052.32029-3-wgong@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-09-23mac80211: always allocate struct ieee802_11_elemsJohannes Berg
As the 802.11 spec evolves, we need to parse more and more elements. This is causing the struct to grow, and we can no longer get away with putting it on the stack. Change the API to always dynamically allocate and return an allocated pointer that must be kfree()d later. As an alternative, I contemplated a scheme whereby we'd say in the code which elements we needed, e.g. DECLARE_ELEMENT_PARSER(elems, SUPPORTED_CHANNELS, CHANNEL_SWITCH, EXT(KEY_DELIVERY)); ieee802_11_parse_elems(..., &elems, ...); and while I think this is possible and will save us a lot since most individual places only care about a small subset of the elements, it ended up being a bit more work since a lot of places do the parsing and then pass the struct to other functions, sometimes with multiple levels. Link: https://lore.kernel.org/r/20210920154009.26caff6b5998.I05ae58768e990e611aee8eca8abefd9d7bc15e05@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-09-23mac80211: mlme: find auth challenge directlyJohannes Berg
There's no need to parse all elements etc. just to find the authentication challenge - use cfg80211_find_elem() instead. This also allows us to remove WLAN_EID_CHALLENGE handling from the element parsing entirely. Link: https://lore.kernel.org/r/20210920154009.45f9b3a15722.Ice3159ffad03a007d6154cbf1fb3a8c48489e86f@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-09-23mac80211: move CRC into struct ieee802_11_elemsJohannes Berg
We're currently returning this value, but to prepare for returning the allocated structure, move it into there. Link: https://lore.kernel.org/r/20210920154009.479b8ebf999d.If0d4ba75ee38998dc3eeae25058aa748efcb2fc9@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-08-26mac80211: parse transmit power envelope elementWen Gong
Parse and store the transmit power envelope element. Signed-off-by: Wen Gong <wgong@codeaurora.org> Link: https://lore.kernel.org/r/20210820122041.12157-8-wgong@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-23mac80211: add HE 6 GHz capability only if supportedJohannes Berg
The HE 6 GHz capability should only be included if there are actually available channels on 6 GHz, and if that's the case we need to get it from the 6 GHz band data, not whatever other band we're on now. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618133832.290bf5c87030.I178aff1c3a6e32456d4ac9238e4a2eb47d209ccd@changeid Link: https://lore.kernel.org/r/iwlwifi.20210618133832.05e935e8dd98.I83ff7eb2ae8ebdf2e30c4fa2461344d9e569f599@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-23mac80211: always include HE 6GHz capability in probe requestJohannes Berg
If HE/6GHz is available (thus we consider dot11HE6GOptionImplemented to be true), then always include the corresponding capability in the probe request as required by the spec. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618133832.25ee4a54a7d0.I8cebd799c85524c8123a11941a104dbdefc03762@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-23mac80211: conditionally advertise HE in probe requestsJohannes Berg
While building probe requests, only enable HE capability if there are actually any channels in the band with HE enabled, otherwise we're not really capable. We're doing the same in association requests, so doing it here makes it consistent. This also makes HE not appear available if it isn't due to regulatory constraints. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618133832.b5513f2af335.Ic01862678712ae4238cea43ad2185928865efad2@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-23mac80211: remove use of ieee80211_get_he_sta_cap()Johannes Berg
All uses of ieee80211_get_he_sta_cap() were actually wrong, in net/mac80211/mlme.c they were wrong because that code is also used for P2P (which is a different interface type), in net/mac80211/main.c that should check all interface types. Fix all that. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618133832.ede114bc8b46.Ibcd9a5d98430e936344eb6d242ef8a65c2f59b74@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-23mac80211: free skb in WEP error caseJohannes Berg
If, for some strange reason, ieee80211_wep_encrypt() fails in ieee80211_send_auth() free the SKB instead of sending out the useless frame, in addition to the warning. This can't really happen since the SKB was freshly allocated. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618133832.98f058d7a8b2.Ie605e6a10e72eae02f5734032826af48b85b6d11@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-18mac80211: handle various extensible elements correctlyJohannes Berg
Various elements are parsed with a requirement to have an exact size, when really we should only check that they have the minimum size that we need. Check only that and therefore ignore any additional data that they might carry. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618133832.cd101f8040a4.Iadf0e9b37b100c6c6e79c7b298cc657c2be9151a@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-06-09mac80211: move interface shutdown out of wiphy lockJohannes Berg
When reconfiguration fails, we shut down everything, but we cannot call cfg80211_shutdown_all_interfaces() with the wiphy mutex held. Since cfg80211 now calls it on resume errors, we only need to do likewise for where we call reconfig (whether directly or indirectly), but not under the wiphy lock. Cc: stable@vger.kernel.org Fixes: 2fe8ef106238 ("cfg80211: change netdev registration/unregistration semantics") Link: https://lore.kernel.org/r/20210608113226.78233c80f548.Iecc104aceb89f0568f50e9670a9cb191a1c8887b@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-04-19mac80211: make ieee80211_vif_to_wdev work when the vif isn't in the driverEmmanuel Grumbach
This will allow the low level driver to get the wdev during the add_interface flow. In order to do that, remove a few checks from there and do not return NULL for vifs that were not yet added to the driver. Note that all the current callers of this helper function assume that the vif already exists: - The callers from the drivers already have a vif pointer. Before this change, ieee80211_vif_to_wdev would return NULL in some cases, but those callers don't even check they get a non-NULL pointer from ieee80211_vif_to_wdev. - The callers from net/mac80211/cfg.c assume the vif is already added to the driver as well. So, this change has no impact on existing callers of this helper function. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210409123755.6078d3517095.I1907a45f267a62dab052bcc44428aa7a2005ffc9@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-03-16mac80211: Allow HE operation to be longer than expected.Brian Norris
We observed some Cisco APs sending the following HE Operation IE in associate response: ff 0a 24 f4 3f 00 01 fc ff 00 00 00 Its HE operation parameter is 0x003ff4, so the expected total length is 7 which does not match the actual length = 10. This causes association failing with "HE AP is missing HE Capability/operation." According to P802.11ax_D4 Table9-94, HE operation is extensible, and according to 802.11-2016 10.27.8, STA should discard the part beyond the maximum length and parse the truncated element. Allow HE operation element to be longer than expected to handle this case and future extensions. Fixes: e4d005b80dee ("mac80211: refactor extended element parsing") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org> Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-01-26cfg80211: avoid holding the RTNL when calling the driverJohannes Berg
Currently, _everything_ in cfg80211 holds the RTNL, and if you have a slow USB device (or a few) you can get some bad lock contention on that. Fix that by re-adding a mutex to each wiphy/rdev as we had at some point, so we have locking for the wireless_dev lists and all the other things in there, and also so that drivers still don't have to worry too much about it (they still won't get parallel calls for a single device). Then, we can restrict the RTNL to a few cases where we add or remove interfaces and really need the added protection. Some of the global list management still also uses the RTNL, since we need to have it anyway for netdev management, but we only hold the RTNL for very short periods of time here. Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-12-12Merge tag 'mac80211-next-for-net-next-2020-12-11' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== A new set of wireless changes: * validate key indices for key deletion * more preamble support in mac80211 * various 6 GHz scan fixes/improvements * a common SAR power limitations API * various small fixes & code improvements * tag 'mac80211-next-for-net-next-2020-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits) mac80211: add ieee80211_set_sar_specs nl80211: add common API to configure SAR power limitations mac80211: fix a mistake check for rx_stats update mac80211: mlme: save ssid info to ieee80211_bss_conf while assoc mac80211: Update rate control on channel change mac80211: don't filter out beacons once we start CSA mac80211: Fix calculation of minimal channel width mac80211: ignore country element TX power on 6 GHz mac80211: use bitfield helpers for BA session action frames mac80211: support Rx timestamp calculation for all preamble types mac80211: don't set set TDLS STA bandwidth wider than possible mac80211: support driver-based disconnect with reconnect hint cfg80211: support immediate reconnect request hint mac80211: use struct assignment for he_obss_pd cfg80211: remove struct ieee80211_he_bss_color nl80211: validate key indexes for cfg80211_registered_device cfg80211: include block-tx flag in channel switch started event mac80211: disallow band-switch during CSA ieee80211: update reduced neighbor report TBTT info length cfg80211: Save the regulatory domain when setting custom regulatory ... ==================== Link: https://lore.kernel.org/r/20201211142552.209018-1-johannes@sipsolutions.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
xdp_return_frame_bulk() needs to pass a xdp_buff to __xdp_return(). strlcpy got converted to strscpy but here it makes no functional difference, so just keep the right code. Conflicts: net/netfilter/nf_tables_api.c Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-11mac80211: support Rx timestamp calculation for all preamble typesAvraham Stern
Add support for calculating the Rx timestamp for HE frames. Since now all frame types are supported, allow setting the Rx timestamp regardless of the frame type. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201206145305.4786559af475.Ia54486bb0a12e5351f9d5c60ef6fcda7c9e7141c@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-12-04mac80211: fix return value of ieee80211_chandef_he_6ghz_operWen Gong
ieee80211_chandef_he_6ghz_oper() needs to return true if it determined a value 6 GHz chandef, fix that. Fixes: 1d00ce807efa ("mac80211: support S1G association") Signed-off-by: Wen Gong <wgong@codeaurora.org> Link: https://lore.kernel.org/r/1606121152-3452-1-git-send-email-wgong@codeaurora.org [rewrite commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-11-13Merge tag 'mac80211-next-for-net-next-2020-11-13' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Some updates: * injection/radiotap updates for new test capabilities * remove WDS support - even years ago when we turned it off by default it was already basically unusable * support for HE (802.11ax) rates for beacons * support for some vendor-specific HE rates * many other small features/cleanups * tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits) nl80211: fix kernel-doc warning in the new SAE attribute cfg80211: remove WDS code mac80211: remove WDS-related code rt2x00: remove WDS code b43legacy: remove WDS code b43: remove WDS code carl9170: remove WDS code ath9k: remove WDS code wireless: remove CONFIG_WIRELESS_WDS mac80211: assure that certain drivers adhere to DONT_REORDER flag mac80211: don't overwrite QoS TID of injected frames mac80211: adhere to Tx control flag that prevents frame reordering mac80211: add radiotap flag to assure frames are not reordered mac80211: save HE oper info in BSS config for mesh cfg80211: add support to configure HE MCS for beacon rate nl80211: fix beacon tx rate mask validation nl80211/cfg80211: fix potential infinite loop cfg80211: Add support to calculate and report 4096-QAM HE rates cfg80211: Add support to configure SAE PWE value to drivers ieee80211: Add definition for WFA DPP ... ==================== Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-11mac80211: remove WDS-related codeJohannes Berg
Now that all the mac80211-based drivers have removed WDS code and in particular the ability to advertise such devices, also remove all the code related to WDS here. Link: https://lore.kernel.org/r/20201109105103.38960c413d46.I3603c90a44562d847c39d15d5ff33d8c00df5834@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-11-07net: mac80211: convert tasklets to use new tasklet_setup() APIAllen Pais
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-09-28mac80211: Support not iterating over not-sdata-in-driver ifacesBen Greear
Allow drivers to request that interface-iterator does NOT iterate over interfaces that are not sdata-in-driver. This will allow us to fix crashes in ath10k (and possibly other drivers). To summarize Johannes' explanation: Consider add interface wlan0 add interface wlan1 iterate active interfaces -> wlan0 wlan1 add interface wlan2 iterate active interfaces -> wlan0 wlan1 wlan2 If you apply this scenario to a restart, which ought to be functionally equivalent to the normal startup, just compressed in time, you're basically saying that today you get add interface wlan0 add interface wlan1 iterate active interfaces -> wlan0 wlan1 wlan2 << problem here add interface wlan2 iterate active interfaces -> wlan0 wlan1 wlan2 which yeah, totally seems wrong. But fixing that to be add interface wlan0 add interface wlan1 iterate active interfaces -> <nothing> add interface wlan2 iterate active interfaces -> <nothing> (or maybe -> wlan0 wlan1 wlan2 if the reconfig already completed) This is also at least somewhat wrong, but better to not iterate over something that exists in the driver than iterate over something that does not. Originally the first issue was causing crashes in testing with lots of station vdevs on an ath10k radio, combined with firmware crashing. I ran with a similar patch for years with no obvious bad results, including significant testing with ath9k and ath10k. Signed-off-by: Ben Greear <greearb@candelatech.com> Link: https://lore.kernel.org/r/20200922191957.25257-1-greearb@candelatech.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28mac80211: support S1G associationThomas Pedersen
The changes required for associating in S1G are: - apply S1G BSS channel info before assoc - mark all S1G STAs as QoS STAs - include and parse AID request element - handle new Association Response format - don't fail assoc if supported rates element is missing Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com [pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss'] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28mac80211: receive and process S1G beaconsThomas Pedersen
S1G beacons are 802.11 Extension Frames, so the fixed header part differs from regular beacons. Add a handler to process S1G beacons and abstract out the fetching of BSSID and element start locations in the beacon body handler. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com [don't rename, small coding style cleanups] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28mac80211: encode listen interval for S1GThomas Pedersen
S1G allows listen interval up to 2^14 * 10000 beacon intervals. In order to do this listen interval needs a scaling factor applied to the lower 14 bits. Calculate this and properly encode the listen interval for S1G STAs. See IEEE802.11ah-2016 Table 9-44a for reference. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-10-thomas@adapt-ip.com [move listen_int_usf into function using it] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28mac80211: convert S1G beacon to scan resultsThomas Pedersen
This commit finds the correct offset for Information Elements in S1G beacon frames so they can be reported in scan results. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-8-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28mac80211: support S1G STA capabilitiesThomas Pedersen
Include the S1G Capabilities element in an association request, and support the cfg80211 capability overrides. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-5-thomas@adapt-ip.com [pass skb to ieee80211_add_s1g_capab_ie(), small code style edits] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-18mac80211: fix 80 MHz association to 160/80+80 AP on 6 GHzJohn Crispin
When trying to associate to an AP support 180 or 80+80 MHz on 6 GHz with a STA that only has 80 Mhz support the cf2 field inside the chandef will get set causing the association to fail when trying to validate the chandef. Fix this by checking the support flags prior to setting cf2. Fixes: 57fa5e85d53ce ("mac80211: determine chandef from HE 6 GHz operation") Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20200918115304.1135693-1-john@phrozen.org [reword commit message a bit] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Resolved kernel/bpf/btf.c using instructions from merge commit 69138b34a7248d2396ab85c8652e20c0c39beaba Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-31mac80211: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20200707204548.GA9320@embeddedor Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-07-31nl80211: S1G band and channel definitionsThomas Pedersen
Gives drivers the definitions needed to advertise support for S1G bands. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-07-30mac80211: fix warning in 6 GHz IE addition in mesh modeRajkumar Manoharan
The commit 24a2042cb22f ("mac80211: add HE 6 GHz Band Capability element") failed to check device capability before adding HE 6 GHz capability element. Below warning is reported in 11ac device in mesh. Fix that by checking device capability at HE 6 GHz cap IE addition in mesh beacon and association request. WARNING: CPU: 1 PID: 1897 at net/mac80211/util.c:2878 ieee80211_ie_build_he_6ghz_cap+0x149/0x150 [mac80211] [ 3138.720358] Call Trace: [ 3138.720361] ieee80211_mesh_build_beacon+0x462/0x530 [mac80211] [ 3138.720363] ieee80211_start_mesh+0xa8/0xf0 [mac80211] [ 3138.720365] __cfg80211_join_mesh+0x122/0x3e0 [cfg80211] [ 3138.720368] nl80211_join_mesh+0x3d3/0x510 [cfg80211] Fixes: 24a2042cb22f ("mac80211: add HE 6 GHz Band Capability element") Reported-by: Markus Theil <markus.theil@tu-ilmenau.de> Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Link: https://lore.kernel.org/r/1593656424-18240-1-git-send-email-rmanohar@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: Add HE 6GHz capabilities element to probe requestIlan Peer
On 6 GHz, the 6 GHz capabilities element should be added, do that. Signed-off-by: Ilan Peer <ilan.peer@intel.com> [add commit message] Link: https://lore.kernel.org/r/20200528213443.8ee764f0cde0.I2b0c66b60e11818c97c9803e04a6a197c6376243@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: determine chandef from HE 6 GHz operationJohannes Berg
Support connecting to HE 6 GHz APs and mesh networks on 6 GHz, where the HT/VHT information is missing but instead the HE 6 GHz band capability is present, and the 6 GHz Operation information field is used to encode the channel configuration instead of the HT/VHT operation elements. Also add some other bits needed to connect to 6 GHz networks. Link: https://lore.kernel.org/r/1589399105-25472-10-git-send-email-rmanohar@codeaurora.org Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Link: https://lore.kernel.org/r/20200528213443.25687d2695bc.I3f9747c1147480f65445f13eda5c4a5ed4e86757@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: avoid using ext NSS high BW if not supportedJohannes Berg
If the AP advertises inconsistent data, namely it has CCFS1 or CCFS2, but doesn't advertise support for 160/80+80 bandwidth or "Extended NSS BW Support", then we cannot use any MCSes in the the higher bandwidth. Thus, avoid connecting with higher bandwidth since it's less efficient that way. Link: https://lore.kernel.org/r/20200528213443.0e55d40c3ccc.I6fd0b4708ebd087e5e46466c3e91f6efbcbef668@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: build HE operation with 6 GHz oper informationRajkumar Manoharan
Add 6 GHz operation information (IEEE 802.11ax/D6.0, Figure 9-787k) while building HE operation element for non-HE AP. This field is used to determine channel information in the absence of HT/VHT IEs. Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Link: https://lore.kernel.org/r/1589399105-25472-8-git-send-email-rmanohar@codeaurora.org [fix skb allocation size] Link: https://lore.kernel.org/r/20200528193455.76796-1-johannes@sipsolutions.net Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: add HE 6 GHz Band Capability elementRajkumar Manoharan
Construct HE 6 GHz band capability element (IEEE 802.11ax/D6.0, 9.4.2.261) for association request and mesh beacon. The 6 GHz capability information is passed by driver through iftypes caps. Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Link: https://lore.kernel.org/r/1589399105-25472-7-git-send-email-rmanohar@codeaurora.org [handle SMPS, adjust for previous patches, reserve SKB space properly, change to handle SKB directly] Link: https://lore.kernel.org/r/20200528213443.643aa8101111.I3f9747c1147480f65445f13eda5c4a5ed4e86757@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-17 22:46:39 +0000