aboutsummaryrefslogtreecommitdiff
path: root/net/ncsi
AgeCommit message (Collapse)Author
2018-11-27net/ncsi: Add NCSI Mellanox OEM commandVijay Khemka
This patch adds OEM Mellanox commands and response handling. It also defines OEM Get MAC Address handler to get and configure the device. ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for getting mac address. ncsi_rsp_handler_oem_mlx: This handles response received for all mellanox OEM commands. ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and set it to device. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Configure multi-package, multi-channel modes with failoverSamuel Mendoza-Jonas
This patch extends the ncsi-netlink interface with two new commands and three new attributes to configure multiple packages and/or channels at once, and configure specific failover modes. NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist of packages or channels allowed to be configured with the NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes respectively. If one of these whitelists is set only packages or channels matching the whitelist are considered for the channel queue in ncsi_choose_active_channel(). These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that multiple packages or channels may be configured simultaneously. NCSI hardware arbitration (HWA) must be available in order to enable multi-package mode. Multi-channel mode is always available. If the NCSI_ATTR_CHANNEL_ID attribute is present in the NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as with the NCSI_CMD_SET_INTERFACE command. The combination of preferred channel and channel whitelist defines a primary channel and the allowed failover channels. If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred channel is configured for Tx/Rx and the other channels are enabled only for Rx. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Reset channel state in ncsi_start_dev()Samuel Mendoza-Jonas
When the NCSI driver is stopped with ncsi_stop_dev() the channel monitors are stopped and the state set to "inactive". However the channels are still configured and active from the perspective of the network controller. We should suspend each active channel but in the context of ncsi_stop_dev() the transmit queue has been or is about to be stopped so we won't have time to do so. Instead when ncsi_start_dev() is called if the NCSI topology has already been probed then call ncsi_reset_dev() to suspend any channels that were previously active. This resets the network controller to a known state, provides an up to date view of channel link state, and makes sure that mode flags such as NCSI_MODE_TX_ENABLE are properly reset. In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c to update the channel configuration more cleanly. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't mark configured channels inactiveSamuel Mendoza-Jonas
The concepts of a channel being 'active' and it having link are slightly muddled in the NCSI driver. Tweak this slightly so that NCSI_CHANNEL_ACTIVE represents a channel that has been configured and enabled, and NCSI_CHANNEL_INACTIVE represents a de-configured channel. This distinction is important because a channel can be 'active' but have its link down; in this case the channel may still need to be configured so that it may receive AEN link-state-change packets. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't deselect package in suspend if activeSamuel Mendoza-Jonas
When a package is deselected all channels of that package cease communication. If there are other channels active on the package of the suspended channel this will disable them as well, so only send a deselect-package command if no other channels are active. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Probe single packages to avoid conflictSamuel Mendoza-Jonas
Currently the NCSI driver sends a select-package command to all possible packages simultaneously to discover what packages are available. However at this stage in the probe process the driver does not know if hardware arbitration is available: if it isn't then this process could cause collisions on the RMII bus when packages try to respond. Update the probe loop to probe each package one by one, and once complete check if HWA is universally supported. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't enable all channels when HWA availableSamuel Mendoza-Jonas
NCSI hardware arbitration allows multiple packages to be enabled at once and share the same wiring. If the NCSI driver recognises that HWA is available it unconditionally enables all packages and channels; but that is a configuration decision rather than something required by HWA. Additionally the current implementation will not failover on link events which can cause connectivity to be lost unless the interface is manually bounced. Retain basic HWA support but remove the separate configuration path to enable all channels, leaving this to be handled by a later implementation. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17net/ncsi: Add NCSI Broadcom OEM commandVijay Khemka
This patch adds OEM Broadcom commands and response handling. It also defines OEM Get MAC Address handler to get and configure the device. ncsi_oem_gma_handler_bcm: This handler send NCSI broadcom command for getting mac address. ncsi_rsp_handler_oem_bcm: This handles response received for all broadcom OEM commands. ncsi_rsp_handler_oem_bcm_gma: This handles get mac address response and set it to device. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15net/ncsi: Extend NC-SI Netlink interface to allow user space to send NC-SI ↵Justin.Lee1@Dell.com
command The new command (NCSI_CMD_SEND_CMD) is added to allow user space application to send NC-SI command to the network card. Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response. The work flow is as below. Request: User space application -> Netlink interface (msg) -> new Netlink handler - ncsi_send_cmd_nl() -> ncsi_xmit_cmd() Response: Response received - ncsi_rcv_rsp() -> internal response handler - ncsi_rsp_handler_xxx() -> ncsi_rsp_handler_netlink() -> ncsi_send_netlink_rsp () -> Netlink interface (msg) -> user space application Command timeout - ncsi_request_timeout() -> ncsi_send_netlink_timeout () -> Netlink interface (msg with zero data length) -> user space application Error: Error detected -> ncsi_send_netlink_err () -> Netlink interface (err msg) -> user space application Signed-off-by: Justin Lee <justin.lee1@dell.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05net/ncsi: Add NCSI OEM command supportVijay Khemka
This patch adds OEM commands and response handling. It also defines OEM command and response structure as per NCSI specification along with its handlers. ncsi_cmd_handler_oem: This is a generic command request handler for OEM commands ncsi_rsp_handler_oem: This is a generic response handler for OEM commands Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Justin Lee <justin.lee1@dell.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-29net/ncsi: remove duplicated include from ncsi-netlink.cYueHaibing
Remove duplicated include. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-22net/ncsi: Fixup .dumpit message flags and ID check in Netlink handlerSamuel Mendoza-Jonas
The ncsi_pkg_info_all_nl() .dumpit handler is missing the NLM_F_MULTI flag, causing additional package information after the first to be lost. Also fixup a sanity check in ncsi_write_package_info() to reject out of range package IDs. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Use netdev_dbg for debug messagesJoel Stanley
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to netdev_dbg. As Joe explains: > netdev_dbg is not included in object code unless > DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set. > And then, it is not emitted into the log unless > DEBUG is set or this specific netdev_dbg is enabled > via the dynamic debug control file. Which is what we're after in this case. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Drop no more channels messageJoel Stanley
This does not provide useful information. As the ncsi maintainer said: > either we get a channel or broadcom has gone out to lunch Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Silence debug messagesJoel Stanley
In normal operation we see this series of messages as the host drives the network device: ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up This makes all of these messages netdev_dbg. They are still useful to debug eg. misbehaving network device firmware, but we do not need them filling up the kernel logs in normal operation. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03net/ncsi: Avoid GFP_KERNEL in response handlerSamuel Mendoza-Jonas
ncsi_rsp_handler_gc() allocates the filter arrays using GFP_KERNEL in softirq context, causing the below backtrace. This allocation is only a few dozen bytes during probing so allocate with GFP_ATOMIC instead. [ 42.813372] BUG: sleeping function called from invalid context at mm/slab.h:416 [ 42.820900] in_atomic(): 1, irqs_disabled(): 0, pid: 213, name: kworker/0:1 [ 42.827893] INFO: lockdep is turned off. [ 42.832023] CPU: 0 PID: 213 Comm: kworker/0:1 Tainted: G W 4.13.16-01441-gad99b38 #65 [ 42.841007] Hardware name: Generic DT based system [ 42.845966] Workqueue: events ncsi_dev_work [ 42.850251] [<8010a494>] (unwind_backtrace) from [<80107510>] (show_stack+0x20/0x24) [ 42.858046] [<80107510>] (show_stack) from [<80612770>] (dump_stack+0x20/0x28) [ 42.865309] [<80612770>] (dump_stack) from [<80148248>] (___might_sleep+0x230/0x2b0) [ 42.873241] [<80148248>] (___might_sleep) from [<80148334>] (__might_sleep+0x6c/0xac) [ 42.881129] [<80148334>] (__might_sleep) from [<80240d6c>] (__kmalloc+0x210/0x2fc) [ 42.888737] [<80240d6c>] (__kmalloc) from [<8060ad54>] (ncsi_rsp_handler_gc+0xd0/0x170) [ 42.896770] [<8060ad54>] (ncsi_rsp_handler_gc) from [<8060b454>] (ncsi_rcv_rsp+0x16c/0x1d4) [ 42.905314] [<8060b454>] (ncsi_rcv_rsp) from [<804d86c8>] (__netif_receive_skb_core+0x3c8/0xb50) [ 42.914158] [<804d86c8>] (__netif_receive_skb_core) from [<804d96cc>] (__netif_receive_skb+0x20/0x7c) [ 42.923420] [<804d96cc>] (__netif_receive_skb) from [<804de4b0>] (netif_receive_skb_internal+0x78/0x6a4) [ 42.932931] [<804de4b0>] (netif_receive_skb_internal) from [<804df980>] (netif_receive_skb+0x78/0x158) [ 42.942292] [<804df980>] (netif_receive_skb) from [<8042f204>] (ftgmac100_poll+0x43c/0x4e8) [ 42.950855] [<8042f204>] (ftgmac100_poll) from [<804e094c>] (net_rx_action+0x278/0x4c4) [ 42.958918] [<804e094c>] (net_rx_action) from [<801016a8>] (__do_softirq+0xe0/0x4c4) [ 42.966716] [<801016a8>] (__do_softirq) from [<8011cd9c>] (do_softirq.part.4+0x50/0x78) [ 42.974756] [<8011cd9c>] (do_softirq.part.4) from [<8011cebc>] (__local_bh_enable_ip+0xf8/0x11c) [ 42.983579] [<8011cebc>] (__local_bh_enable_ip) from [<804dde08>] (__dev_queue_xmit+0x260/0x890) [ 42.992392] [<804dde08>] (__dev_queue_xmit) from [<804df1f0>] (dev_queue_xmit+0x1c/0x20) [ 43.000689] [<804df1f0>] (dev_queue_xmit) from [<806099c0>] (ncsi_xmit_cmd+0x1c0/0x244) [ 43.008763] [<806099c0>] (ncsi_xmit_cmd) from [<8060dc14>] (ncsi_dev_work+0x2e0/0x4c8) [ 43.016725] [<8060dc14>] (ncsi_dev_work) from [<80133dfc>] (process_one_work+0x214/0x6f8) [ 43.024940] [<80133dfc>] (process_one_work) from [<80134328>] (worker_thread+0x48/0x558) [ 43.033070] [<80134328>] (worker_thread) from [<8013ba80>] (kthread+0x130/0x174) [ 43.040506] [<8013ba80>] (kthread) from [<80102950>] (ret_from_fork+0x14/0x24) Fixes: 062b3e1b6d4f ("net/ncsi: Refactor MAC, VLAN filters") Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Filling in the padding slot in the bpf structure as a bug fix in 'ne' overlapped with actually using that padding area for something in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-31net/ncsi: Fix array size in dumpit handlerSamuel Mendoza-Jonas
With CONFIG_CC_STACKPROTECTOR enabled the kernel panics as below when parsing a NCSI_CMD_PKG_INFO command: [ 150.149711] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08 [ 150.149711] [ 150.159919] CPU: 0 PID: 1301 Comm: ncsi-netlink Not tainted 4.13.16-468cbec6d2c91239332cb91b1f0a73aafcb6f0c6 #1 [ 150.170004] Hardware name: Generic DT based system [ 150.174852] [<80109930>] (unwind_backtrace) from [<80106bc4>] (show_stack+0x20/0x24) [ 150.182641] [<80106bc4>] (show_stack) from [<805d36e4>] (dump_stack+0x20/0x28) [ 150.189888] [<805d36e4>] (dump_stack) from [<801163ac>] (panic+0xdc/0x278) [ 150.196780] [<801163ac>] (panic) from [<801162cc>] (__stack_chk_fail+0x20/0x24) [ 150.204111] [<801162cc>] (__stack_chk_fail) from [<805cff08>] (ncsi_pkg_info_all_nl+0x244/0x258) [ 150.212912] [<805cff08>] (ncsi_pkg_info_all_nl) from [<804f939c>] (genl_lock_dumpit+0x3c/0x54) [ 150.221535] [<804f939c>] (genl_lock_dumpit) from [<804f873c>] (netlink_dump+0xf8/0x284) [ 150.229550] [<804f873c>] (netlink_dump) from [<804f8d44>] (__netlink_dump_start+0x124/0x17c) [ 150.237992] [<804f8d44>] (__netlink_dump_start) from [<804f9880>] (genl_rcv_msg+0x1c8/0x3d4) [ 150.246440] [<804f9880>] (genl_rcv_msg) from [<804f9174>] (netlink_rcv_skb+0xd8/0x134) [ 150.254361] [<804f9174>] (netlink_rcv_skb) from [<804f96a4>] (genl_rcv+0x30/0x44) [ 150.261850] [<804f96a4>] (genl_rcv) from [<804f7790>] (netlink_unicast+0x198/0x234) [ 150.269511] [<804f7790>] (netlink_unicast) from [<804f7ffc>] (netlink_sendmsg+0x368/0x3b0) [ 150.277783] [<804f7ffc>] (netlink_sendmsg) from [<804abea4>] (sock_sendmsg+0x24/0x34) [ 150.285625] [<804abea4>] (sock_sendmsg) from [<804ac1dc>] (___sys_sendmsg+0x244/0x260) [ 150.293556] [<804ac1dc>] (___sys_sendmsg) from [<804ad98c>] (__sys_sendmsg+0x5c/0x9c) [ 150.301400] [<804ad98c>] (__sys_sendmsg) from [<804ad9e4>] (SyS_sendmsg+0x18/0x1c) [ 150.308984] [<804ad9e4>] (SyS_sendmsg) from [<80102640>] (ret_fast_syscall+0x0/0x3c) [ 150.316743] ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08 This turns out to be because the attrs array in ncsi_pkg_info_all_nl() is initialised to a length of NCSI_ATTR_MAX which is the maximum attribute number, not the number of attributes. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-29net: remove unnecessary genlmsg_cancel() callsYueHaibing
the message be freed immediately, no need to trim it back to the previous size. Inspired by commit 7a9b3ec1e19f ("nl80211: remove unnecessary genlmsg_cancel() calls") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-17net/ncsi: prevent a couple array underflowsDan Carpenter
We recently refactored this code and introduced a static checker warning. Smatch complains that if cmd->index is zero then we would underflow the arrays. That's obviously true. The question is whether we prevent cmd->index from being zero at a different level. I've looked at the code and I don't immediately see a check for that. Fixes: 062b3e1b6d4f ("net/ncsi: Refactor MAC, VLAN filters") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-17net/ncsi: Refactor MAC, VLAN filtersSamuel Mendoza-Jonas
The NCSI driver defines a generic ncsi_channel_filter struct that can be used to store arbitrarily formatted filters, and several generic methods of accessing data stored in such a filter. However in both the driver and as defined in the NCSI specification there are only two actual filters: VLAN ID filters and MAC address filters. The splitting of the MAC filter into unicast, multicast, and mixed is also technically not necessary as these are stored in the same location in hardware. To save complexity, particularly in the set up and accessing of these generic filters, remove them in favour of two specific structs. These can be acted on directly and do not need several generic helper functions to use. This also fixes a memory error found by KASAN on ARM32 (which is not upstream yet), where response handlers accessing a filter's data field could write past allocated memory. [ 114.926512] ================================================================== [ 114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58 [ 114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546 [ 114.947593] [ 114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13 ... [ 115.170233] The buggy address belongs to the object at 94888540 [ 115.170233] which belongs to the cache kmalloc-32 of size 32 [ 115.181917] The buggy address is located 24 bytes inside of [ 115.181917] 32-byte region [94888540, 94888560) [ 115.192115] The buggy address belongs to the page: [ 115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1 [ 115.204200] flags: 0x100(slab) [ 115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0 [ 115.215444] page dumped because: kasan: bad access detected [ 115.221036] [ 115.222544] Memory state around the buggy address: [ 115.227384] 94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc [ 115.233959] 94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc [ 115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc [ 115.247077] ^ [ 115.252523] 94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc [ 115.259093] 94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc [ 115.265639] ================================================================== Reported-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-27net/ncsi: check for null return from call to nla_nest_startColin Ian King
The call to nla_nest_start calls nla_put which can lead to a NULL return so it's possible for attr to become NULL and we can potentially get a NULL pointer dereference on attr. Fix this by checking for a NULL return. Detected by CoverityScan, CID#1466125 ("Dereference null return") Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-08net/ncsi: unlock on error in ncsi_set_interface_nl()Dan Carpenter
There are two error paths which are missing unlocks in this function. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-08net/ncsi: use kfree_skb() instead of kfree()Dan Carpenter
We're supposed to use kfree_skb() to free these sk_buffs. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-05net/ncsi: Add generic netlink familySamuel Mendoza-Jonas
Add a generic netlink family for NCSI. This supports three commands; NCSI_CMD_PKG_INFO which returns information on packages and their associated channels, NCSI_CMD_SET_INTERFACE which allows a specific package or package/channel combination to be set as the preferred choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-18net/ncsi: Don't take any action on HNCDSC AENSamuel Mendoza-Jonas
The current HNCDSC handler takes the status flag from the AEN packet and will update or change the current channel based on this flag and the current channel status. However the flag from the HNCDSC packet merely represents the host link state. While the state of the host interface is potentially interesting information it should not affect the state of the NCSI link. Indeed the NCSI specification makes no mention of any recommended action related to the host network controller driver state. Update the HNCDSC handler to record the host network driver status but take no other action. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-21treewide: setup_timer() -> timer_setup() (2 field)Kees Cook
This converts all remaining setup_timer() calls that use a nested field to reach a struct timer_list. Coccinelle does not have an easy way to match multiple fields, so a new script is needed to change the matches of "&_E->_timer" into "&_E->_field1._timer" in all the rules. spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup-2fields.cocci @fix_address_of depends@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _field1; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_field1._timer, NULL, _E); +timer_setup(&_E->_field1._timer, NULL, 0); | -setup_timer(&_E->_field1._timer, NULL, (_cast_data)_E); +timer_setup(&_E->_field1._timer, NULL, 0); | -setup_timer(&_E._field1._timer, NULL, &_E); +timer_setup(&_E._field1._timer, NULL, 0); | -setup_timer(&_E._field1._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._field1._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _field1; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_field1._timer, _callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, &_callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, _callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)_callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | _E->_field1._timer@_stl.function = _callback; | _E->_field1._timer@_stl.function = &_callback; | _E->_field1._timer@_stl.function = (_cast_func)_callback; | _E->_field1._timer@_stl.function = (_cast_func)&_callback; | _E._field1._timer@_stl.function = _callback; | _E._field1._timer@_stl.function = &_callback; | _E._field1._timer@_stl.function = (_cast_func)_callback; | _E._field1._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _field1._timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _field1._timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _field1._timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_field1._timer, _callback, 0); +setup_timer(&_E->_field1._timer, _callback, (_cast_data)_E); | -timer_setup(&_E._field1._timer, _callback, 0); +setup_timer(&_E._field1._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_field1._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_field1._timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_field1._timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_field1._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_field1._timer | -(_cast_data)&_E +&_E._field1._timer | -_E +&_E->_field1._timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _field1; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_field1._timer, _callback, 0); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, _callback, 0L); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, _callback, 0UL); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, 0); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, 0L); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, 0UL); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_field1._timer, _callback, 0); +timer_setup(&_field1._timer, _callback, 0); | -setup_timer(&_field1._timer, _callback, 0L); +timer_setup(&_field1._timer, _callback, 0); | -setup_timer(&_field1._timer, _callback, 0UL); +timer_setup(&_field1._timer, _callback, 0); | -setup_timer(_field1._timer, _callback, 0); +timer_setup(_field1._timer, _callback, 0); | -setup_timer(_field1._timer, _callback, 0L); +timer_setup(_field1._timer, _callback, 0); | -setup_timer(_field1._timer, _callback, 0UL); +timer_setup(_field1._timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-11net/ncsi: Don't return error on normal responseSamuel Mendoza-Jonas
Several response handlers return EBUSY if the data corresponding to the command/response pair is already set. There is no reason to return an error here; the channel is advertising something as enabled because we told it to enable it, and it's possible that the feature has been enabled previously. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-11net/ncsi: Improve general state loggingSamuel Mendoza-Jonas
The NCSI driver is mostly silent which becomes a headache when trying to determine what has occurred on the NCSI connection. This adds additional logging in a few key areas such as state transitions and calling out certain errors more visibly. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-03net/ncsi: Make local function ncsi_get_filter() staticWei Yongjun
Fixes the following sparse warnings: net/ncsi/ncsi-manage.c:41:5: warning: symbol 'ncsi_get_filter' was not declared. Should it be static? Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Fix length of GVI response packetGavin Shan
The length of GVI (GetVersionInfo) response packet should be 40 instead of 36. This issue was found from /sys/kernel/debug/ncsi/eth0/stats. # ethtool --ncsi eth0 swstats : RESPONSE OK TIMEOUT ERROR ======================================= GVI 0 0 2 With this applied, no error reported on GVI response packets: # ethtool --ncsi eth0 swstats : RESPONSE OK TIMEOUT ERROR ======================================= GVI 2 0 0 Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Enforce failover on link monitor timeoutGavin Shan
The NCSI channel has been configured to provide service if its link monitor timer is enabled, regardless of its state (inactive or active). So the timeout event on the link monitor indicates the out-of-service on that channel, for which a failover is needed. This sets NCSI_DEV_RESHUFFLE flag to enforce failover on link monitor timeout, regardless the channel's original state (inactive or active). Also, the link is put into "down" state to give the failing channel lowest priority when selecting for the active channel. The state of failing channel should be set to active in order for deinitialization and failover to be done. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Disable HWA mode when no channels are foundGavin Shan
When there are no NCSI channels probed, HWA (Hardware Arbitration) mode is enabled. It's not correct because HWA depends on the fact: NCSI channels exist and all of them support HWA mode. This disables HWA when no channels are probed. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Stop monitor if channel times out or is inactiveSamuel Mendoza-Jonas
ncsi_channel_monitor() misses stopping the channel monitor in several places that it should, causing a WARN_ON_ONCE() to trigger when the monitor is re-started later, eg: [ 459.040000] WARNING: CPU: 0 PID: 1093 at net/ncsi/ncsi-manage.c:269 ncsi_start_channel_monitor+0x7c/0x90 [ 459.040000] CPU: 0 PID: 1093 Comm: kworker/0:3 Not tainted 4.10.17-gaca2fdd #140 [ 459.040000] Hardware name: ASpeed SoC [ 459.040000] Workqueue: events ncsi_dev_work [ 459.040000] [<80010094>] (unwind_backtrace) from [<8000d950>] (show_stack+0x20/0x24) [ 459.040000] [<8000d950>] (show_stack) from [<801dbf70>] (dump_stack+0x20/0x28) [ 459.040000] [<801dbf70>] (dump_stack) from [<80018d7c>] (__warn+0xe0/0x108) [ 459.040000] [<80018d7c>] (__warn) from [<80018e70>] (warn_slowpath_null+0x30/0x38) [ 459.040000] [<80018e70>] (warn_slowpath_null) from [<803f6a08>] (ncsi_start_channel_monitor+0x7c/0x90) [ 459.040000] [<803f6a08>] (ncsi_start_channel_monitor) from [<803f7664>] (ncsi_configure_channel+0xdc/0x5fc) [ 459.040000] [<803f7664>] (ncsi_configure_channel) from [<803f8160>] (ncsi_dev_work+0xac/0x474) [ 459.040000] [<803f8160>] (ncsi_dev_work) from [<8002d244>] (process_one_work+0x1e0/0x450) [ 459.040000] [<8002d244>] (process_one_work) from [<8002d510>] (worker_thread+0x5c/0x570) [ 459.040000] [<8002d510>] (worker_thread) from [<80033614>] (kthread+0x124/0x164) [ 459.040000] [<80033614>] (kthread) from [<8000a5e8>] (ret_from_fork+0x14/0x2c) This also updates the monitor instead of just returning if ncsi_xmit_cmd() fails to send the get-link-status command so that the monitor properly times out. Fixes: e6f44ed6d04d3 "net/ncsi: Package and channel management" Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Fix AEN HNCDSC packet lengthSamuel Mendoza-Jonas
Correct the value of the HNCDSC AEN packet. Fixes: 7a82ecf4cfb85 "net/ncsi: NCSI AEN packet handler" Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-11net/ncsi: Don't limit vids based on hot_channelSamuel Mendoza-Jonas
Currently we drop any new VLAN ids if there are more than the current (or last used) channel can support. Most importantly this is a problem if no channel has been selected yet, resulting in a segfault. Secondly this does not necessarily reflect the capabilities of any other channels. Instead only drop a new VLAN id if we are already tracking the maximum allowed by the NCSI specification. Per-channel limits are already handled by ncsi_add_filter(), but add a message to set_one_vid() to make it obvious that the channel can not support any more VLAN ids. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-05net/ncsi: fix ncsi_vlan_rx_{add,kill}_vid referencesArnd Bergmann
We get a new link error in allmodconfig kernels after ftgmac100 started using the ncsi helpers: ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined! ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined! Related to that, we get another error when CONFIG_NET_NCSI is disabled: drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'? drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'? This fixes both problems at once, using a 'static inline' stub helper for the disabled case, and exporting the functions when they are present. Fixes: 51564585d8c6 ("ftgmac100: Support NCSI VLAN filtering when available") Fixes: 21acf63013ed ("net/ncsi: Configure VLAN tag filter") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-28net/ncsi: Configure VLAN tag filterSamuel Mendoza-Jonas
Make use of the ndo_vlan_rx_{add,kill}_vid callbacks to have the NCSI stack process new VLAN tags and configure the channel VLAN filter appropriately. Several VLAN tags can be set and a "Set VLAN Filter" packet must be sent for each one, meaning the ncsi_dev_state_config_svf state must be repeated. An internal list of VLAN tags is maintained, and compared against the current channel's ncsi_channel_filter in order to keep track within the state. VLAN filters are removed in a similar manner, with the introduction of the ncsi_dev_state_config_clear_vids state. The maximum number of VLAN tag filters is determined by the "Get Capabilities" response from the channel. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-28net/ncsi: Fix several packet definitionsSamuel Mendoza-Jonas
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: make skb_push & __skb_push return void pointersJohannes Berg
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: convert many more places to skb_put_zero()Johannes Berg
There were many places that my previous spatch didn't find, as pointed out by yuan linyu in various patches. The following spatch found many more and also removes the now unnecessary casts: @@ identifier p, p2; expression len; expression skb; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_zero(skb, len); | -p = (t)skb_put(skb, len); +p = skb_put_zero(skb, len); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, len); | -memset(p, 0, len); ) @@ type t, t2; identifier p, p2; expression skb; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, sizeof(*p)); | -memset(p, 0, sizeof(*p)); ) @@ expression skb, len; @@ -memset(skb_put(skb, len), 0, len); +skb_put_zero(skb, len); Apply it to the tree (with one manual fixup to keep the comment in vxlan.c, which spatch removed.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Improve HNCDSC AEN handlerGavin Shan
This improves AEN handler for Host Network Controller Driver Status Change (HNCDSC): * The channel's lock should be hold when accessing its state. * Do failover when host driver isn't ready. * Configure channel when host driver becomes ready. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Choose hot channel as active one if necessaryGavin Shan
The issue was found on BCM5718 which has two NCSI channels in one package: C0 and C1. C0 is in link-up state while C1 is in link-down state. C0 is chosen as active channel until unplugging and plugging C0's cable: On unplugging C0's cable, LSC (Link State Change) AEN packet received on C0 to report link-down event. After that, C1 is chosen as active channel. LSC AEN for link-up event is lost on C0 when plugging C0's cable back. We lose the network even C0 is usable. This resolves the issue by recording the (hot) channel that was ever chosen as active one. The hot channel is chosen to be active one if none of available channels in link-up state. With this, C0 is still the active one after unplugging C0's cable. LSC AEN packet received on C0 when plugging its cable back. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Fix stale link state of inactive channels on failoverGavin Shan
The issue was found on BCM5718 which has two NCSI channels in one package: C0 and C1. Both of them are connected to different LANs, means they are in link-up state and C0 is chosen as the active one until resetting BCM5718 happens as below. Resetting BCM5718 results in LSC (Link State Change) AEN packet received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet received on C0 to report link-down, it fails over to C1 because C1 is in link-up state as software can see. However, C1 is in link-down state in hardware. It means the link state is out of synchronization between hardware and software, resulting in inappropriate channel (C1) selected as active one. This resolves the issue by sending separate GLS (Get Link Status) commands to all channels in the package before trying to do failover. The last link states of all channels in the package are retrieved. With it, C0 (not C1) is selected as active one as expected. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Avoid if statements in ncsi_suspend_channel()Gavin Shan
There are several if/else statements in the state machine implemented by switch/case in ncsi_suspend_channel() to avoid duplicated code. It makes the code a bit hard to be understood. This drops if/else statements in ncsi_suspend_channel() to improve the code readability as Joel Stanley suggested. Also, it becomes easy to add more states in the state machine without affecting current code. No logical changes introduced by this. Suggested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Introduce ncsi_stop_dev()Gavin Shan
This introduces ncsi_stop_dev(), as counterpart to ncsi_start_dev(), to stop the NCSI device so that it can be reenabled in future. This API should be called when the network device driver is going to shutdown the device. There are 3 things done in the function: Stop the channel monitoring; Reset channels to inactive state; Report NCSI link down. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Rework the channel monitoringGavin Shan
The original NCSI channel monitoring was implemented based on a backoff algorithm: the GLS response should be received in the specified interval. Otherwise, the channel is regarded as dead and failover should be taken if current channel is an active one. There are several problems in the implementation: (A) On BCM5718, we found when the IID (Instance ID) in the GLS command packet changes from 255 to 1, the response corresponding to IID#1 never comes in. It means we cannot make the unfair judgement that the channel is dead when one response is missed. (B) The code's readability should be improved. (C) We should do failover when current channel is active one and the channel monitoring should be marked as disabled before doing failover. This reworks the channel monitoring to address all above issues. The fields for channel monitoring is put into separate struct and the state of channel monitoring is predefined. The channel is regarded alive if the network controller responses to one of two GLS commands or both of them in 5 seconds. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Allow to extend NCSI request propertiesGavin Shan
There is only one NCSI request property for now: the response for the sent command need drive the workqueue or not. So we had one field (@driven) for the purpose. We lost the flexibility to extend NCSI request properties. This replaces @driven with @flags and @req_flags in NCSI request and NCSI command argument struct. Each bit of the newly introduced field can be used for one property. No functional changes introduced. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Rework request index allocationGavin Shan
The NCSI request index (struct ncsi_request::id) is put into instance ID (IID) field while sending NCSI command packet. It was designed the available IDs are given in round-robin fashion. @ndp->request_id was introduced to represent the next available ID, but it has been used as number of successively allocated IDs. It breaks the round-robin design. Besides, we shouldn't put 0 to NCSI command packet's IID field, meaning ID#0 should be reserved according section 6.3.1.1 in NCSI spec (v1.1.0). This fixes above two issues. With it applied, the available IDs will be assigned in round-robin fashion and ID#0 won't be assigned. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 08:54:07 +0000