| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 71e41286203c017d24f041a7cd71abea7ca7b1e0.
mmap()/munmap() can not be backed by kmalloced pages :
We fault in :
VM_BUG_ON_PAGE(PageSlab(page), page);
unmap_single_vma+0x8a/0x110
unmap_vmas+0x4b/0x90
unmap_region+0xc9/0x140
do_munmap+0x274/0x360
vm_munmap+0x81/0xc0
SyS_munmap+0x2b/0x40
do_syscall_64+0x13e/0x1c0
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Fixes: 71e41286203c ("packet: switch kvzalloc to allocate memory")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: John Sperbeck <jsperbeck@google.com>
Bisected-by: John Sperbeck <jsperbeck@google.com>
Cc: Zhang Yu <zhangyu31@baidu.com>
Cc: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patches includes following change:
*Use modern kvzalloc()/kvfree() instead of custom allocations.
*Remove order argument for alloc_pg_vec, it can get from req.
*Remove order argument for free_pg_vec, free_pg_vec now uses
kvfree which does not need order argument.
*Remove pg_vec_order from struct packet_ring_buffer, no longer
need to save/restore 'order'
*Remove variable 'order' for packet_set_ring, it is now unused
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes in RXRPC, changing to ktime_get_seconds() whilst
adding some tracepoints.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes: eb73190f4fbe ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These semicolons are not needed. Just remove them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts were trivial overlapping changes, so reasonably
easy to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If variable length link layer headers result in a packet shorter
than dev->hard_header_len, reset the network header offset. Else
skb->mac_len may exceed skb->len after skb_mac_reset_len.
packet_sendmsg_spkt already has similar logic.
Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a generic version of the ndo_select_queue functions for
either returning 0 or selecting a queue based on the processor ID. This is
generally meant to just reduce the number of functions we have to change
in the future when we have to deal with ndo_select_queue changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba19978 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For raw layer-2 packets, copy the desired future transmit time from
the CMSG cookie into the skb.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We should put copy_skb in receive_queue only after
a successful call to virtio_net_hdr_from_skb().
syzbot report :
BUG: KASAN: use-after-free in __skb_unlink include/linux/skbuff.h:1843 [inline]
BUG: KASAN: use-after-free in __skb_dequeue include/linux/skbuff.h:1863 [inline]
BUG: KASAN: use-after-free in skb_dequeue+0x16a/0x180 net/core/skbuff.c:2815
Read of size 8 at addr ffff8801b044ecc0 by task syz-executor217/4553
CPU: 0 PID: 4553 Comm: syz-executor217 Not tainted 4.18.0-rc1+ #111
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
__skb_unlink include/linux/skbuff.h:1843 [inline]
__skb_dequeue include/linux/skbuff.h:1863 [inline]
skb_dequeue+0x16a/0x180 net/core/skbuff.c:2815
skb_queue_purge+0x26/0x40 net/core/skbuff.c:2852
packet_set_ring+0x675/0x1da0 net/packet/af_packet.c:4331
packet_release+0x630/0xd90 net/packet/af_packet.c:2991
__sock_release+0xd7/0x260 net/socket.c:603
sock_close+0x19/0x20 net/socket.c:1186
__fput+0x35b/0x8b0 fs/file_table.c:209
____fput+0x15/0x20 fs/file_table.c:243
task_work_run+0x1ec/0x2a0 kernel/task_work.c:113
exit_task_work include/linux/task_work.h:22 [inline]
do_exit+0x1b08/0x2750 kernel/exit.c:865
do_group_exit+0x177/0x440 kernel/exit.c:968
__do_sys_exit_group kernel/exit.c:979 [inline]
__se_sys_exit_group kernel/exit.c:977 [inline]
__x64_sys_exit_group+0x3e/0x50 kernel/exit.c:977
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4448e9
Code: Bad RIP value.
RSP: 002b:00007ffd5f777ca8 EFLAGS: 00000202 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00000000004448e9
RDX: 00000000004448e9 RSI: 000000000000fcfb RDI: 0000000000000001
RBP: 00000000006cf018 R08: 00007ffd0000a45b R09: 0000000000000000
R10: 00007ffd5f777e48 R11: 0000000000000202 R12: 00000000004021f0
R13: 0000000000402280 R14: 0000000000000000 R15: 0000000000000000
Allocated by task 4553:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc4/0xe0 mm/kasan/kasan.c:553
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490
kmem_cache_alloc+0x12e/0x760 mm/slab.c:3554
skb_clone+0x1f5/0x500 net/core/skbuff.c:1282
tpacket_rcv+0x28f7/0x3200 net/packet/af_packet.c:2221
deliver_skb net/core/dev.c:1925 [inline]
deliver_ptype_list_skb net/core/dev.c:1940 [inline]
__netif_receive_skb_core+0x1bfb/0x3680 net/core/dev.c:4611
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693
netif_receive_skb_internal+0x12e/0x7d0 net/core/dev.c:4767
netif_receive_skb+0xbf/0x420 net/core/dev.c:4791
tun_rx_batched.isra.55+0x4ba/0x8c0 drivers/net/tun.c:1571
tun_get_user+0x2af1/0x42f0 drivers/net/tun.c:1981
tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:2009
call_write_iter include/linux/fs.h:1795 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x6c6/0x9f0 fs/read_write.c:487
vfs_write+0x1f8/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 4553:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kmem_cache_free+0x86/0x2d0 mm/slab.c:3756
kfree_skbmem+0x154/0x230 net/core/skbuff.c:582
__kfree_skb net/core/skbuff.c:642 [inline]
kfree_skb+0x1a5/0x580 net/core/skbuff.c:659
tpacket_rcv+0x189e/0x3200 net/packet/af_packet.c:2385
deliver_skb net/core/dev.c:1925 [inline]
deliver_ptype_list_skb net/core/dev.c:1940 [inline]
__netif_receive_skb_core+0x1bfb/0x3680 net/core/dev.c:4611
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693
netif_receive_skb_internal+0x12e/0x7d0 net/core/dev.c:4767
netif_receive_skb+0xbf/0x420 net/core/dev.c:4791
tun_rx_batched.isra.55+0x4ba/0x8c0 drivers/net/tun.c:1571
tun_get_user+0x2af1/0x42f0 drivers/net/tun.c:1981
tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:2009
call_write_iter include/linux/fs.h:1795 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x6c6/0x9f0 fs/read_write.c:487
vfs_write+0x1f8/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8801b044ecc0
which belongs to the cache skbuff_head_cache of size 232
The buggy address is located 0 bytes inside of
232-byte region [ffff8801b044ecc0, ffff8801b044eda8)
The buggy address belongs to the page:
page:ffffea0006c11380 count:1 mapcount:0 mapping:ffff8801d9be96c0 index:0x0
flags: 0x2fffc0000000100(slab)
raw: 02fffc0000000100 ffffea0006c17988 ffff8801d9bec248 ffff8801d9be96c0
raw: 0000000000000000 ffff8801b044e040 000000010000000c 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801b044eb80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff8801b044ec00: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
>ffff8801b044ec80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^
ffff8801b044ed00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801b044ed80: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
Fixes: 58d19b19cd99 ("packet: vnet_hdr support for tpacket_rcv")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vzalloc() function has no 2-factor argument form, so multiplication
factors need to be wrapped in array_size(). This patch replaces cases of:
vzalloc(a * b)
with:
vzalloc(array_size(a, b))
as well as handling cases of:
vzalloc(a * b * c)
with:
vzalloc(array3_size(a, b, c))
This does, however, attempt to ignore constant size factors like:
vzalloc(4 * 1024)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
vzalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
vzalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
vzalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
vzalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
vzalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
vzalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
vzalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
vzalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
vzalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
vzalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
vzalloc(
- sizeof(TYPE) * (COUNT_ID)
+ array_size(COUNT_ID, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(TYPE) * COUNT_ID
+ array_size(COUNT_ID, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(TYPE) * (COUNT_CONST)
+ array_size(COUNT_CONST, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(TYPE) * COUNT_CONST
+ array_size(COUNT_CONST, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(THING) * (COUNT_ID)
+ array_size(COUNT_ID, sizeof(THING))
, ...)
|
vzalloc(
- sizeof(THING) * COUNT_ID
+ array_size(COUNT_ID, sizeof(THING))
, ...)
|
vzalloc(
- sizeof(THING) * (COUNT_CONST)
+ array_size(COUNT_CONST, sizeof(THING))
, ...)
|
vzalloc(
- sizeof(THING) * COUNT_CONST
+ array_size(COUNT_CONST, sizeof(THING))
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
vzalloc(
- SIZE * COUNT
+ array_size(COUNT, SIZE)
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
vzalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vzalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
vzalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
vzalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
vzalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
vzalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
vzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
vzalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
vzalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
vzalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
vzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
vzalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vzalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
vzalloc(C1 * C2 * C3, ...)
|
vzalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants.
@@
expression E1, E2;
constant C1, C2;
@@
(
vzalloc(C1 * C2, ...)
|
vzalloc(
- E1 * E2
+ array_size(E1, E2)
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Tun, tap, virtio, packet and uml vector all use struct virtio_net_hdr
to communicate packet metadata to userspace.
For skbuffs with vlan, the first two return the packet as it may have
existed on the wire, inserting the VLAN tag in the user buffer. Then
virtio_net_hdr.csum_start needs to be adjusted by VLAN_HLEN bytes.
Commit f09e2249c4f5 ("macvtap: restore vlan header on user read")
added this feature to macvtap. Commit 3ce9b20f1971 ("macvtap: Fix
csum_start when VLAN tags are present") then fixed up csum_start.
Virtio, packet and uml do not insert the vlan header in the user
buffer.
When introducing virtio_net_hdr_from_skb to deduplicate filling in
the virtio_net_hdr, the variant from macvtap which adds VLAN_HLEN was
applied uniformly, breaking csum offset for packets with vlan on
virtio and packet.
Make insertion of VLAN_HLEN optional. Convert the callers to pass it
when needed.
Fixes: e858fae2b0b8f4 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Fixes: 1276f24eeef2 ("packet: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull procfs updates from Al Viro:
"Christoph's proc_create_... cleanups series"
* 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (44 commits)
xfs, proc: hide unused xfs procfs helpers
isdn/gigaset: add back gigaset_procinfo assignment
proc: update SIZEOF_PDE_INLINE_NAME for the new pde fields
tty: replace ->proc_fops with ->proc_show
ide: replace ->proc_fops with ->proc_show
ide: remove ide_driver_proc_write
isdn: replace ->proc_fops with ->proc_show
atm: switch to proc_create_seq_private
atm: simplify procfs code
bluetooth: switch to proc_create_seq_data
netfilter/x_tables: switch to proc_create_seq_private
netfilter/xt_hashlimit: switch to proc_create_{seq,single}_data
neigh: switch to proc_create_seq_data
hostap: switch to proc_create_{seq,single}_data
bonding: switch to proc_create_seq_data
rtc/proc: switch to proc_create_single_data
drbd: switch to proc_create_single
resource: switch to proc_create_seq_data
staging/rtl8192u: simplify procfs code
jfs: simplify procfs code
...
|
|
syzbot was able to trick af_packet again [1]
Various commits tried to address the problem in the past,
but failed to take into account V3 header size.
[1]
tpacket_rcv: packet too big, clamped from 72 to 4294967224. macoff=96
BUG: KASAN: use-after-free in prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline]
BUG: KASAN: use-after-free in prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039
Write of size 2 at addr ffff8801cb62000e by task kworker/1:2/2106
CPU: 1 PID: 2106 Comm: kworker/1:2 Not tainted 4.17.0-rc7+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b9/0x294 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
__asan_report_store2_noabort+0x17/0x20 mm/kasan/report.c:436
prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline]
prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039
__packet_lookup_frame_in_block net/packet/af_packet.c:1094 [inline]
packet_current_rx_frame net/packet/af_packet.c:1117 [inline]
tpacket_rcv+0x1866/0x3340 net/packet/af_packet.c:2282
dev_queue_xmit_nit+0x891/0xb90 net/core/dev.c:2018
xmit_one net/core/dev.c:3049 [inline]
dev_hard_start_xmit+0x16b/0xc10 net/core/dev.c:3069
__dev_queue_xmit+0x2724/0x34c0 net/core/dev.c:3584
dev_queue_xmit+0x17/0x20 net/core/dev.c:3617
neigh_resolve_output+0x679/0xad0 net/core/neighbour.c:1358
neigh_output include/net/neighbour.h:482 [inline]
ip6_finish_output2+0xc9c/0x2810 net/ipv6/ip6_output.c:120
ip6_finish_output+0x5fe/0xbc0 net/ipv6/ip6_output.c:154
NF_HOOK_COND include/linux/netfilter.h:277 [inline]
ip6_output+0x227/0x9b0 net/ipv6/ip6_output.c:171
dst_output include/net/dst.h:444 [inline]
NF_HOOK include/linux/netfilter.h:288 [inline]
ndisc_send_skb+0x100d/0x1570 net/ipv6/ndisc.c:491
ndisc_send_ns+0x3c1/0x8d0 net/ipv6/ndisc.c:633
addrconf_dad_work+0xbef/0x1340 net/ipv6/addrconf.c:4033
process_one_work+0xc1e/0x1b50 kernel/workqueue.c:2145
worker_thread+0x1cc/0x1440 kernel/workqueue.c:2279
kthread+0x345/0x410 kernel/kthread.c:240
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:412
The buggy address belongs to the page:
page:ffffea00072d8800 count:0 mapcount:-127 mapping:0000000000000000 index:0xffff8801cb620e80
flags: 0x2fffc0000000000()
raw: 02fffc0000000000 0000000000000000 ffff8801cb620e80 00000000ffffff80
raw: ffffea00072e3820 ffffea0007132d20 0000000000000002 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801cb61ff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff8801cb61ff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8801cb620000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff8801cb620080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff8801cb620100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Fixes: 2b6867c2ce76 ("net/packet: fix overflow in check for priv area size")
Fixes: dc808110bb62 ("packet: handle too big packets for PACKET_V3")
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of easy overlapping changes in the confict
resolutions here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit b84bbaf7a6c8 ("packet: in packet_snd start writing at link
layer allocation") ensures that packet_snd always starts writing
the link layer header in reserved headroom allocated for this
purpose.
This is needed because packets may be shorter than hard_header_len,
in which case the space up to hard_header_len may be zeroed. But
that necessary padding is not accounted for in skb->len.
The fix, however, is buggy. It calls skb_push, which grows skb->len
when moving skb->data back. But in this case packet length should not
change.
Instead, call skb_reserve, which moves both skb->data and skb->tail
back, without changing length.
Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation")
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variants of proc_create{,_data} that directly take a struct seq_operations
and deal with network namespaces in ->open and ->release. All callers of
proc_create + seq_open_net converted over, and seq_{open,release}_net are
removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Packet sockets allow construction of packets shorter than
dev->hard_header_len to accommodate protocols with variable length
link layer headers. These packets are padded to dev->hard_header_len,
because some device drivers interpret that as a minimum packet size.
packet_snd reserves dev->hard_header_len bytes on allocation.
SOCK_DGRAM sockets call skb_push in dev_hard_header() to ensure that
link layer headers are stored in the reserved range. SOCK_RAW sockets
do the same in tpacket_snd, but not in packet_snd.
Syzbot was able to send a zero byte packet to a device with massive
116B link layer header, causing padding to cross over into skb_shinfo.
Fix this by writing from the start of the llheader reserved range also
in the case of packet_snd/SOCK_RAW.
Update skb_set_network_header to the new offset. This also corrects
it for SOCK_DGRAM, where it incorrectly double counted reserve due to
the skb_push in dev_hard_header.
Fixes: 9ed988cd5915 ("packet: validate variable length ll headers")
Reported-by: syzbot+71d74a5406d02057d559@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new dev_direct_xmit will be used by AF_XDP in later commits.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Updates to the bitfields in struct packet_sock are not atomic.
Serialize these read-modify-write cycles.
Move po->running into a separate variable. Its writes are protected by
po->bind_lock (except for one startup case at packet_create). Also
replace a textual precondition warning with lockdep annotation.
All others are set only in packet_setsockopt. Serialize these
updates by holding the socket lock. Analogous to other field updates,
also hold the lock when testing whether a ring is active (pg_vec).
Fixes: 8dc419447415 ("[PACKET]: Add optional checksum computation for recvmsg")
Reported-by: DaeRyong Jeong <threeearcat@gmail.com>
Reported-by: Byoungyoung Lee <byoungyoung@purdue.edu>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to remove the race caught by syzbot [1], we need
to lock the socket before using po->tp_version as this could
change under us otherwise.
This means lock_sock() and release_sock() must be done by
packet_set_ring() callers.
[1] :
BUG: KMSAN: uninit-value in packet_set_ring+0x1254/0x3870 net/packet/af_packet.c:4249
CPU: 0 PID: 20195 Comm: syzkaller707632 Not tainted 4.16.0+ #83
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676
packet_set_ring+0x1254/0x3870 net/packet/af_packet.c:4249
packet_setsockopt+0x12c6/0x5a90 net/packet/af_packet.c:3662
SYSC_setsockopt+0x4b8/0x570 net/socket.c:1849
SyS_setsockopt+0x76/0xa0 net/socket.c:1828
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x449099
RSP: 002b:00007f42b5307ce8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 000000000070003c RCX: 0000000000449099
RDX: 0000000000000005 RSI: 0000000000000107 RDI: 0000000000000003
RBP: 0000000000700038 R08: 000000000000001c R09: 0000000000000000
R10: 00000000200000c0 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000080eecf R14: 00007f42b53089c0 R15: 0000000000000001
Local variable description: ----req_u@packet_setsockopt
Variable was created at:
packet_setsockopt+0x13f/0x5a90 net/packet/af_packet.c:3612
SYSC_setsockopt+0x4b8/0x570 net/socket.c:1849
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These pernet_operations just create and destroy /proc entry,
and another operations do not touch it.
Also, nobody else are interested in foreign net::packet::sklist.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
|
|
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612f0b0adb6046f19b906609e4fe8b1ba
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements asynchronous crypto callbacks
and a backlog handler that can be used when IPsec
is done at layer 2 in the TX path. It also extends
the skb validate functions so that we can update
the driver transmit return codes based on async
crypto operation or to indicate that we queued the
packet in a backlog queue.
Joint work with: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
syzbot reported crashes [1] and provided a C repro easing bug hunting.
When/if packet_do_bind() calls __unregister_prot_hook() and releases
po->bind_lock, another thread can run packet_notifier() and process an
NETDEV_UP event.
This calls register_prot_hook() and hooks again the socket right before
first thread is able to grab again po->bind_lock.
Fixes this issue by temporarily setting po->num to 0, as suggested by
David Miller.
[1]
dev_remove_pack: ffff8801bf16fa80 not found
------------[ cut here ]------------
kernel BUG at net/core/dev.c:7945! ( BUG_ON(!list_empty(&dev->ptype_all)); )
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
device syz0 entered promiscuous mode
CPU: 0 PID: 3161 Comm: syzkaller404108 Not tainted 4.14.0+ #190
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801cc57a500 task.stack: ffff8801cc588000
RIP: 0010:netdev_run_todo+0x772/0xae0 net/core/dev.c:7945
RSP: 0018:ffff8801cc58f598 EFLAGS: 00010293
RAX: ffff8801cc57a500 RBX: dffffc0000000000 RCX: ffffffff841f75b2
RDX: 0000000000000000 RSI: 1ffff100398b1ede RDI: ffff8801bf1f8810
device syz0 entered promiscuous mode
RBP: ffff8801cc58f898 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801bf1f8cd8
R13: ffff8801cc58f870 R14: ffff8801bf1f8780 R15: ffff8801cc58f7f0
FS: 0000000001716880(0000) GS:ffff8801db400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020b13000 CR3: 0000000005e25000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
rtnl_unlock+0xe/0x10 net/core/rtnetlink.c:106
tun_detach drivers/net/tun.c:670 [inline]
tun_chr_close+0x49/0x60 drivers/net/tun.c:2845
__fput+0x333/0x7f0 fs/file_table.c:210
____fput+0x15/0x20 fs/file_table.c:244
task_work_run+0x199/0x270 kernel/task_work.c:113
exit_task_work include/linux/task_work.h:22 [inline]
do_exit+0x9bb/0x1ae0 kernel/exit.c:865
do_group_exit+0x149/0x400 kernel/exit.c:968
SYSC_exit_group kernel/exit.c:979 [inline]
SyS_exit_group+0x1d/0x20 kernel/exit.c:977
entry_SYSCALL_64_fastpath+0x1f/0x96
RIP: 0033:0x44ad19
Fixes: 30f7ea1c2b5f ("packet: race condition in packet_bind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller found a race condition fanout_demux_rollover() while removing
a packet socket from a fanout group.
po->rollover is read and operated on during packet_rcv_fanout(), via
fanout_demux_rollover(), but the pointer is currently cleared before the
synchronization in packet_release(). It is safer to delay the cleanup
until after synchronize_net() has been called, ensuring all calls to
packet_rcv_fanout() for this socket have finished.
To further simplify synchronization around the rollover structure, set
po->rollover in fanout_add() only if there are no errors. This removes
the need for rcu in the struct and in the call to
packet_getsockopt(..., PACKET_ROLLOVER_STATS, ...).
Crashing stack trace:
fanout_demux_rollover+0xb6/0x4d0 net/packet/af_packet.c:1392
packet_rcv_fanout+0x649/0x7c8 net/packet/af_packet.c:1487
dev_queue_xmit_nit+0x835/0xc10 net/core/dev.c:1953
xmit_one net/core/dev.c:2975 [inline]
dev_hard_start_xmit+0x16b/0xac0 net/core/dev.c:2995
__dev_queue_xmit+0x17a4/0x2050 net/core/dev.c:3476
dev_queue_xmit+0x17/0x20 net/core/dev.c:3509
neigh_connected_output+0x489/0x720 net/core/neighbour.c:1379
neigh_output include/net/neighbour.h:482 [inline]
ip6_finish_output2+0xad1/0x22a0 net/ipv6/ip6_output.c:120
ip6_finish_output+0x2f9/0x920 net/ipv6/ip6_output.c:146
NF_HOOK_COND include/linux/netfilter.h:239 [inline]
ip6_output+0x1f4/0x850 net/ipv6/ip6_output.c:163
dst_output include/net/dst.h:459 [inline]
NF_HOOK.constprop.35+0xff/0x630 include/linux/netfilter.h:250
mld_sendpack+0x6a8/0xcc0 net/ipv6/mcast.c:1660
mld_send_initial_cr.part.24+0x103/0x150 net/ipv6/mcast.c:2072
mld_send_initial_cr net/ipv6/mcast.c:2056 [inline]
ipv6_mc_dad_complete+0x99/0x130 net/ipv6/mcast.c:2079
addrconf_dad_completed+0x595/0x970 net/ipv6/addrconf.c:4039
addrconf_dad_work+0xac9/0x1160 net/ipv6/addrconf.c:3971
process_one_work+0xbf0/0x1bc0 kernel/workqueue.c:2113
worker_thread+0x223/0x1990 kernel/workqueue.c:2247
kthread+0x35e/0x430 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:432
Fixes: 0648ab70afe6 ("packet: rollover prepare: per-socket state")
Fixes: 509c7a1ecc860 ("packet: avoid panic in packet_getsockopt()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Mike Maloney <maloney@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Be sure that packet.sklist initialized in net_init hook was return
to initial state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Mike Maloney <maloney@google.com>
Cc: Jarno Rajahalme <jarno@ovn.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller got crashes in packet_getsockopt() processing
PACKET_ROLLOVER_STATS command while another thread was managing
to change po->rollover
Using RCU will fix this bug. We might later add proper RCU annotations
for sparse sake.
In v2: I replaced kfree(rollover) in fanout_add() to kfree_rcu()
variant, as spotted by John.
Fixes: a9b6391814d5 ("packet: rollover statistics")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: John Sperbeck <jsperbeck@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet socket option po->has_vnet_hdr can be updated concurrently with
other operations if no ring is attached.
Do not test the option twice in packet_snd, as the value may change in
between calls. A race on setsockopt disable may cause a packet > mtu
to be sent without having GSO options set.
Fixes: bfd5f4a3d605 ("packet: Add GSO/csum offload support.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once a socket has po->fanout set, it remains a member of the group
until it is destroyed. The prot_hook must be constant and identical
across sockets in the group.
If fanout_add races with packet_do_bind between the test of po->fanout
and taking the lock, the bind call may make type or dev inconsistent
with that of the fanout group.
Hold po->bind_lock when testing po->fanout to avoid this race.
I had to introduce artificial delay (local_bh_enable) to actually
observe the race.
Fixes: dc99f600698d ("packet: Add fanout support.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet socket bind operations must hold the po->bind_lock. This keeps
po->running consistent with whether the socket is actually on a ptype
list to receive packets.
fanout_add unbinds a socket and its packet_rcv/tpacket_rcv call, then
binds the fanout object to receive through packet_rcv_fanout.
Make it hold the po->bind_lock when testing po->running and rebinding.
Else, it can race with other rebind operations, such as that in
packet_set_ring from packet_rcv to tpacket_rcv. Concurrent updates
can result in a socket being added to a fanout group twice, causing
use-after-free KASAN bug reports, among others.
Reported independently by both trinity and syzkaller.
Verified that the syzkaller reproducer passes after this patch.
Fixes: dc99f600698d ("packet: Add fanout support.")
Reported-by: nixioaming <nixiaoming@huawei.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
