| Age | Commit message (Collapse) | Author |
|---|
|
Offloading police with action TC_ACT_UNSPEC was erroneously disabled even
though it was supported by mlx5 matchall offload implementation, which
didn't verify the action type but instead assumed that any single police
action attached to matchall classifier is a 'continue' action. Lack of
action type check made it non-obvious what mlx5 matchall implementation
actually supports and caused implementers and reviewers of referenced
commits to disallow it as a part of improved validation code.
Fixes: b8cd5831c61c ("net: flow_offload: add tc police action parameters")
Fixes: b50e462bc22d ("net/sched: act_police: Add extack messages for offload failure")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If during an action flush operation one of the actions is still being
referenced, the flush operation is aborted and the kernel returns to
user space with an error. However, if the kernel was able to flush, for
example, 3 actions and failed on the fourth, the kernel will not notify
user space that it deleted 3 actions before failing.
This patch fixes that behaviour by notifying user space of how many
actions were deleted before flush failed and by setting extack with a
message describing what happened.
Fixes: 55334a5db5cd ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As reported by Yuming, currently tc always show a latency of UINT_MAX
for netem Qdisc's on 32-bit platforms:
$ tc qdisc add dev dummy0 root netem latency 100ms
$ tc qdisc show dev dummy0
qdisc netem 8001: root refcnt 2 limit 1000 delay 275s 275s
^^^^^^^^^^^^^^^^
Let us take a closer look at netem_dump():
qopt.latency = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->latency,
UINT_MAX);
qopt.latency is __u32, psched_tdiff_t is signed long,
(psched_tdiff_t)(UINT_MAX) is negative for 32-bit platforms, so
qopt.latency is always UINT_MAX.
Fix it by using psched_time_t (u64) instead.
Note: confusingly, users have two ways to specify 'latency':
1. normally, via '__u32 latency' in struct tc_netem_qopt;
2. via the TCA_NETEM_LATENCY64 attribute, which is s64.
For the second case, theoretically 'latency' could be negative. This
patch ignores that corner case, since it is broken (i.e. assigning a
negative s64 to __u32) anyways, and should be handled separately.
Thanks Ted Lin for the analysis [1] .
[1] https://github.com/raspberrypi/linux/issues/3512
Reported-by: Yuming Chen <chenyuming.junnan@bytedance.com>
Fixes: 112f9cb65643 ("netem: convert to qdisc_watchdog_schedule_ns")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20220616234336.2443-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The tcf_ct_flow_table_fill_tuple_ipv6() function is supposed to return
false on failure. It should not return negatives because that means
succes/true.
Fixes: fcb6aa86532c ("act_ct: Support GRE offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://lore.kernel.org/r/YpYFnbDxFl6tQ3Bn@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
drivers/net/ethernet/mellanox/mlx5/core/main.c
b33886971dbc ("net/mlx5: Initialize flow steering during driver probe")
40379a0084c2 ("net/mlx5_fpga: Drop INNOVA TLS support")
f2b41b32cde8 ("net/mlx5: Remove ipsec_ops function table")
https://lore.kernel.org/all/20220519040345.6yrjromcdistu7vh@sx1/
16d42d313350 ("net/mlx5: Drain fw_reset when removing device")
8324a02c342a ("net/mlx5: Add exit route when waiting for FW")
https://lore.kernel.org/all/20220519114119.060ce014@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
e274f7154008 ("selftests: mptcp: add subflow limits test-cases")
b6e074e171bc ("selftests: mptcp: add infinite map testcase")
5ac1d2d63451 ("selftests: mptcp: Add tests for userspace PM type")
https://lore.kernel.org/all/20220516111918.366d747f@canb.auug.org.au/
net/mptcp/options.c
ba2c89e0ea74 ("mptcp: fix checksum byte order")
1e39e5a32ad7 ("mptcp: infinite mapping sending")
ea66758c1795 ("tcp: allow MPTCP to update the announced window")
https://lore.kernel.org/all/20220519115146.751c3a37@canb.auug.org.au/
net/mptcp/pm.c
95d686517884 ("mptcp: fix subflow accounting on close")
4d25247d3ae4 ("mptcp: bypass in-kernel PM restrictions for non-kernel PMs")
https://lore.kernel.org/all/20220516111435.72f35dca@canb.auug.org.au/
net/mptcp/subflow.c
ae66fb2ba6c3 ("mptcp: Do TCP fallback on early DSS checksum failure")
0348c690ed37 ("mptcp: add the fallback check")
f8d4bcacff3b ("mptcp: infinite mapping receiving")
https://lore.kernel.org/all/20220519115837.380bb8d4@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot was able to trigger an Out-of-Bound on the pedit action:
UBSAN: shift-out-of-bounds in net/sched/act_pedit.c:238:43
shift exponent 1400735974 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 3606 Comm: syz-executor151 Not tainted 5.18.0-rc5-syzkaller-00165-g810c2f0a3f86 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x50 lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x187 lib/ubsan.c:322
tcf_pedit_init.cold+0x1a/0x1f net/sched/act_pedit.c:238
tcf_action_init_1+0x414/0x690 net/sched/act_api.c:1367
tcf_action_init+0x530/0x8d0 net/sched/act_api.c:1432
tcf_action_add+0xf9/0x480 net/sched/act_api.c:1956
tc_ctl_action+0x346/0x470 net/sched/act_api.c:2015
rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5993
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:725
____sys_sendmsg+0x6e2/0x800 net/socket.c:2413
___sys_sendmsg+0xf3/0x170 net/socket.c:2467
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fe36e9e1b59
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffef796fe88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe36e9e1b59
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
RBP: 00007fe36e9a5d00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe36e9a5d90
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com
Fixes: 8b796475fd78 ("net/sched: act_pedit: really ensure the skb is writable")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk->sk_bound_dev_if can change under us, use READ_ONCE() annotation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently pedit tries to ensure that the accessed skb offset
is writable via skb_unclone(). The action potentially allows
touching any skb bytes, so it may end-up modifying shared data.
The above causes some sporadic MPTCP self-test failures, due to
this code:
tc -n $ns2 filter add dev ns2eth$i egress \
protocol ip prio 1000 \
handle 42 fw \
action pedit munge offset 148 u8 invert \
pipe csum tcp \
index 100
The above modifies a data byte outside the skb head and the skb is
a cloned one, carrying a TCP output packet.
This change addresses the issue by keeping track of a rough
over-estimate highest skb offset accessed by the action and ensuring
such offset is really writable.
Note that this may cause performance regressions in some scenarios,
but hopefully pedit is not in the critical path.
Fixes: db2c24175d14 ("act_pedit: access skb->data safely")
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/1fcf78e6679d0a287dd61bb0f04730ce33b3255d.1652194627.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
d08ed852560e ("net: lan966x: Make sure to release ptp interrupt")
c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before this patch the existence of vlan filters was conditional on the vlan
protocol being matched in the tc rule. For example, the following rule:
tc filter add dev eth1 ingress flower vlan_prio 5
was illegal because vlan protocol (e.g. 802.1q) does not appear in the rule.
Remove the above restriction by looking at the num_of_vlans filter to
allow further matching on vlan attributes. The following rule becomes
legal as a result of this commit:
tc filter add dev eth1 ingress flower num_of_vlans 1 vlan_prio 5
because having num_of_vlans==1 implies that the packet is single tagged.
Change is_vlan_key helper to look at the number of vlans in addition to
the vlan ethertype. The outcome of this change is that outer (e.g. vlan_prio)
and inner (e.g. cvlan_prio) tag vlan filters require the number of vlan
tags to be greater then 0 and 1 accordingly.
As a result of is_vlan_key change, the ethertype may be set to 0 when
matching on the number of vlans. Update fl_set_key_vlan to avoid setting
key, mask vlan_tpid for the 0 ethertype.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are bookkeeping parts of the new num_of_vlans filter.
Defines, dump, load and set are being done here.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whitespace only.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are somewhat repetitive ethertype checks in fl_set_key. Refactor
them into is_vlan_key helper function.
To make the changes clearer, avoid touching identation levels. This is
the job for the next patch in the series.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows users to pick queue_mapping, range
from A to B. Then we can load balance packets from A
to B tx queue. The range is an unsigned 16bit value
in decimal format.
$ tc filter ... action skbedit queue_mapping skbhash A B
"skbedit queue_mapping QUEUE_MAPPING" (from "man 8 tc-skbedit")
is enhanced with flags: SKBEDIT_F_TXQ_SKBHASH
+----+ +----+ +----+
| P1 | | P2 | | Pn |
+----+ +----+ +----+
| | |
+-----------+-----------+
|
| clsact/skbedit
| MQ
v
+-----------+-----------+
| q0 | qn | qm
v v v
HTB/FQ FIFO ... FIFO
For example:
If P1 sends out packets to different Pods on other host, and
we want distribute flows from qn - qm. Then we can use skb->hash
as hash.
setup commands:
$ NETDEV=eth0
$ ip netns add n1
$ ip link add ipv1 link $NETDEV type ipvlan mode l2
$ ip link set ipv1 netns n1
$ ip netns exec n1 ifconfig ipv1 2.2.2.100/24 up
$ tc qdisc add dev $NETDEV clsact
$ tc filter add dev $NETDEV egress protocol ip prio 1 \
flower skip_hw src_ip 2.2.2.100 action skbedit queue_mapping skbhash 2 6
$ tc qdisc add dev $NETDEV handle 1: root mq
$ tc qdisc add dev $NETDEV parent 1:1 handle 2: htb
$ tc class add dev $NETDEV parent 2: classid 2:1 htb rate 100kbit
$ tc class add dev $NETDEV parent 2: classid 2:2 htb rate 200kbit
$ tc qdisc add dev $NETDEV parent 1:2 tbf rate 100mbit burst 100mb latency 1
$ tc qdisc add dev $NETDEV parent 1:3 pfifo
$ tc qdisc add dev $NETDEV parent 1:4 pfifo
$ tc qdisc add dev $NETDEV parent 1:5 pfifo
$ tc qdisc add dev $NETDEV parent 1:6 pfifo
$ tc qdisc add dev $NETDEV parent 1:7 pfifo
$ ip netns exec n1 iperf3 -c 2.2.2.1 -i 1 -t 10 -P 10
pick txqueue from 2 - 6:
$ ethtool -S $NETDEV | grep -i tx_queue_[0-9]_bytes
tx_queue_0_bytes: 42
tx_queue_1_bytes: 0
tx_queue_2_bytes: 11442586444
tx_queue_3_bytes: 7383615334
tx_queue_4_bytes: 3981365579
tx_queue_5_bytes: 3983235051
tx_queue_6_bytes: 6706236461
tx_queue_7_bytes: 42
tx_queue_8_bytes: 0
tx_queue_9_bytes: 0
txqueues 2 - 6 are mapped to classid 1:3 - 1:7
$ tc -s class show dev $NETDEV
...
class mq 1:3 root leaf 8002:
Sent 11949133672 bytes 7929798 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq 1:4 root leaf 8003:
Sent 7710449050 bytes 5117279 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq 1:5 root leaf 8004:
Sent 4157648675 bytes 2758990 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq 1:6 root leaf 8005:
Sent 4159632195 bytes 2759990 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq 1:7 root leaf 8006:
Sent 7003169603 bytes 4646912 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
...
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexander Lobakin <alobakin@pm.me>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Wei Wang <weiwan@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch fixes issue:
* If we install tc filters with act_skbedit in clsact hook.
It doesn't work, because netdev_core_pick_tx() overwrites
queue_mapping.
$ tc filter ... action skbedit queue_mapping 1
And this patch is useful:
* We can use FQ + EDT to implement efficient policies. Tx queues
are picked by xps, ndo_select_queue of netdev driver, or skb hash
in netdev_core_pick_tx(). In fact, the netdev driver, and skb
hash are _not_ under control. xps uses the CPUs map to select Tx
queues, but we can't figure out which task_struct of pod/containter
running on this cpu in most case. We can use clsact filters to classify
one pod/container traffic to one Tx queue. Why ?
In containter networking environment, there are two kinds of pod/
containter/net-namespace. One kind (e.g. P1, P2), the high throughput
is key in these applications. But avoid running out of network resource,
the outbound traffic of these pods is limited, using or sharing one
dedicated Tx queues assigned HTB/TBF/FQ Qdisc. Other kind of pods
(e.g. Pn), the low latency of data access is key. And the traffic is not
limited. Pods use or share other dedicated Tx queues assigned FIFO Qdisc.
This choice provides two benefits. First, contention on the HTB/FQ Qdisc
lock is significantly reduced since fewer CPUs contend for the same queue.
More importantly, Qdisc contention can be eliminated completely if each
CPU has its own FIFO Qdisc for the second kind of pods.
There must be a mechanism in place to support classifying traffic based on
pods/container to different Tx queues. Note that clsact is outside of Qdisc
while Qdisc can run a classifier to select a sub-queue under the lock.
In general recording the decision in the skb seems a little heavy handed.
This patch introduces a per-CPU variable, suggested by Eric.
The xmit.skip_txqueue flag is firstly cleared in __dev_queue_xmit().
- Tx Qdisc may install that skbedit actions, then xmit.skip_txqueue flag
is set in qdisc->enqueue() though tx queue has been selected in
netdev_tx_queue_mapping() or netdev_core_pick_tx(). That flag is cleared
firstly in __dev_queue_xmit(), is useful:
- Avoid picking Tx queue with netdev_tx_queue_mapping() in next netdev
in such case: eth0 macvlan - eth0.3 vlan - eth0 ixgbe-phy:
For example, eth0, macvlan in pod, which root Qdisc install skbedit
queue_mapping, send packets to eth0.3, vlan in host. In __dev_queue_xmit() of
eth0.3, clear the flag, does not select tx queue according to skb->queue_mapping
because there is no filters in clsact or tx Qdisc of this netdev.
Same action taked in eth0, ixgbe in Host.
- Avoid picking Tx queue for next packet. If we set xmit.skip_txqueue
in tx Qdisc (qdisc->enqueue()), the proper way to clear it is clearing it
in __dev_queue_xmit when processing next packets.
For performance reasons, use the static key. If user does not config the NET_EGRESS,
the patch will not be compiled.
+----+ +----+ +----+
| P1 | | P2 | | Pn |
+----+ +----+ +----+
| | |
+-----------+-----------+
|
| clsact/skbedit
| MQ
v
+-----------+-----------+
| q0 | q1 | qn
v v v
HTB/FQ HTB/FQ ... FIFO
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexander Lobakin <alobakin@pm.me>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Wei Wang <weiwan@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While investigating a related syzbot report,
I found that whenever call to tcf_exts_init()
from u32_init_knode() is failing, we end up
with an elevated refcount on ht->refcnt
To avoid that, only increase the refcount after
all possible errors have been evaluated.
Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We are now able to detect extra put_net() at the moment
they happen, instead of much later in correct code paths.
u32_init_knode() / tcf_exts_init() populates the ->exts.net
pointer, but as mentioned in tcf_exts_init(),
the refcount on netns has not been elevated yet.
The refcount is taken only once tcf_exts_get_net()
is called.
So the two u32_destroy_key() calls from u32_change()
are attempting to release an invalid reference on the netns.
syzbot report:
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 0 PID: 21708 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Modules linked in:
CPU: 0 PID: 21708 Comm: syz-executor.5 Not tainted 5.18.0-rc2-next-20220412-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Code: 1d 14 b6 b2 09 31 ff 89 de e8 6d e9 89 fd 84 db 75 e0 e8 84 e5 89 fd 48 c7 c7 40 aa 26 8a c6 05 f4 b5 b2 09 01 e8 e5 81 2e 05 <0f> 0b eb c4 e8 68 e5 89 fd 0f b6 1d e3 b5 b2 09 31 ff 89 de e8 38
RSP: 0018:ffffc900051af1b0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000040000 RSI: ffffffff8160a0c8 RDI: fffff52000a35e28
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff81604a9e R11: 0000000000000000 R12: 1ffff92000a35e3b
R13: 00000000ffffffef R14: ffff8880211a0194 R15: ffff8880577d0a00
FS: 00007f25d183e700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f19c859c028 CR3: 0000000051009000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__refcount_dec include/linux/refcount.h:344 [inline]
refcount_dec include/linux/refcount.h:359 [inline]
ref_tracker_free+0x535/0x6b0 lib/ref_tracker.c:118
netns_tracker_free include/net/net_namespace.h:327 [inline]
put_net_track include/net/net_namespace.h:341 [inline]
tcf_exts_put_net include/net/pkt_cls.h:255 [inline]
u32_destroy_key.isra.0+0xa7/0x2b0 net/sched/cls_u32.c:394
u32_change+0xe01/0x3140 net/sched/cls_u32.c:909
tc_new_tfilter+0x98d/0x2200 net/sched/cls_api.c:2148
rtnetlink_rcv_msg+0x80d/0xb80 net/core/rtnetlink.c:6016
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2495
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:725
____sys_sendmsg+0x6e2/0x800 net/socket.c:2413
___sys_sendmsg+0xf3/0x170 net/socket.c:2467
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f25d0689049
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f25d183e168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f25d079c030 RCX: 00007f25d0689049
RDX: 0000000000000000 RSI: 0000000020000340 RDI: 0000000000000005
RBP: 00007f25d06e308d R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffd0b752e3f R14: 00007f25d183e300 R15: 0000000000022000
</TASK>
Fixes: 35c55fc156d8 ("cls_u32: use tcf_exts_get_net() before call_rcu()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For some unknown reason qdisc_reset() is using
a convoluted way of freeing two lists of skbs.
Use __skb_queue_purge() instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20220414011004.2378350-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
A user may set the SO_TXTIME socket option to ensure a packet is send
at a given time. The taprio scheduler has to confirm, that it is allowed
to send a packet at that given time, by a check against the packet time
schedule. The scheduler drop the packet, if the gates are closed at the
given send time.
The check, if SO_TXTIME is set, may fail since sk_flags are part of an
union and the union is used otherwise. This happen, if a socket is not
a full socket, like a request socket for example.
Add a check to verify, if the union is used for sk_flags.
Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode")
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when inserting a new filter that needs to sit at the head
of chain 0, it will first update the heads pointer on all devices using
the (shared) block, and only then complete the initialization of the new
element so that it has a "next" element.
This can lead to a situation that the chain 0 head is propagated to
another CPU before the "next" initialization is done. When this race
condition is triggered, packets being matched on that CPU will simply
miss all other filters, and will flow through the stack as if there were
no other filters installed. If the system is using OVS + TC, such
packets will get handled by vswitchd via upcall, which results in much
higher latency and reordering. For other applications it may result in
packet drops.
This is reproducible with a tc only setup, but it varies from system to
system. It could be reproduced with a shared block amongst 10 veth
tunnels, and an ingress filter mirroring packets to another veth.
That's because using the last added veth tunnel to the shared block to
do the actual traffic, it makes the race window bigger and easier to
trigger.
The fix is rather simple, to just initialize the next pointer of the new
filter instance (tp) before propagating the head change.
The fixes tag is pointing to the original code though this issue should
only be observed when using it unlocked.
Fixes: 2190d1d0944f ("net: sched: introduce helpers to work with filter chains")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/b97d5f4eaffeeb9d058155bcab63347527261abf.1649341369.git.marcelo.leitner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The various error paths of tc_setup_offload_action() now report specific
error messages. Remove the generic messages to avoid overwriting the
more specific ones.
Before:
# tc filter add dev dummy0 ingress pref 1 proto ip flower skip_sw dst_ip 198.51.100.1 action police rate 100Mbit burst 10000
Error: cls_flower: Failed to setup flow action.
We have an error talking to the kernel
After:
# tc filter add dev dummy0 ingress pref 1 proto ip flower skip_sw dst_ip 198.51.100.1 action police rate 100Mbit burst 10000
Error: act_police: Offload not supported when conform/exceed action is "reclassify".
We have an error talking to the kernel
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The various error paths of tc_setup_offload_action() now report specific
error messages. Remove the generic messages to avoid overwriting the
more specific ones.
Before:
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action police rate 100Mbit burst 10000
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
After:
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action police rate 100Mbit burst 10000
Error: act_police: Offload not supported when conform/exceed action is "reclassify".
We have an error talking to the kernel
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add an extack message when the
requested action does not support offload.
Example:
# echo 1 > /sys/kernel/tracing/events/netlink/netlink_extack/enable
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action nat ingress 192.0.2.1 198.51.100.1
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-181 [000] b..1. 88.406093: netlink_extack: msg=Action does not support offload
tc-181 [000] ..... 88.406108: netlink_extack: msg=cls_matchall: Failed to setup flow action
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add an extack message when
vlan action offload fails.
Currently, the failure cannot be triggered, but add a message in case
the action is extended in the future to support more than the current
set of modes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add an extack message when
tunnel_key action offload fails.
Currently, the failure cannot be triggered, but add a message in case
the action is extended in the future to support more than set/release
modes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add extack messages when
skbedit action offload fails.
Example:
# echo 1 > /sys/kernel/tracing/events/netlink/netlink_extack/enable
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action skbedit queue_mapping 1234
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-185 [002] b..1. 31.802414: netlink_extack: msg=act_skbedit: Offload not supported when "queue_mapping" option is used
tc-185 [002] ..... 31.802418: netlink_extack: msg=cls_matchall: Failed to setup flow action
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action skbedit inheritdsfield
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-187 [002] b..1. 45.985145: netlink_extack: msg=act_skbedit: Offload not supported when "inheritdsfield" option is used
tc-187 [002] ..... 45.985160: netlink_extack: msg=cls_matchall: Failed to setup flow action
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add extack messages when
police action offload fails.
Example:
# echo 1 > /sys/kernel/tracing/events/netlink/netlink_extack/enable
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action police rate 100Mbit burst 10000
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-182 [000] b..1. 21.592969: netlink_extack: msg=act_police: Offload not supported when conform/exceed action is "reclassify"
tc-182 [000] ..... 21.592982: netlink_extack: msg=cls_matchall: Failed to setup flow action
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action police rate 100Mbit burst 10000 conform-exceed drop/continue
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-184 [000] b..1. 38.882579: netlink_extack: msg=act_police: Offload not supported when conform/exceed action is "continue"
tc-184 [000] ..... 38.882593: netlink_extack: msg=cls_matchall: Failed to setup flow action
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add an extack message when
pedit action offload fails.
Currently, the failure cannot be triggered, but add a message in case
the action is extended in the future to support more than set/add
commands.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add extack messages when mpls
action offload fails.
Example:
# echo 1 > /sys/kernel/tracing/events/netlink/netlink_extack/enable
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action mpls dec_ttl
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-182 [000] b..1. 18.693915: netlink_extack: msg=act_mpls: Offload not supported when "dec_ttl" option is used
tc-182 [000] ..... 18.693921: netlink_extack: msg=cls_matchall: Failed to setup flow action
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add an extack message when
mirred action offload fails.
Currently, the failure cannot be triggered, but add a message in case
the action is extended in the future to support more than ingress/egress
mirror/redirect.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better error reporting to user space, add extack messages when gact
action offload fails.
Example:
# echo 1 > /sys/kernel/tracing/events/netlink/netlink_extack/enable
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action continue
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-181 [002] b..1. 105.493450: netlink_extack: msg=act_gact: Offload of "continue" action is not supported
tc-181 [002] ..... 105.493466: netlink_extack: msg=cls_matchall: Failed to setup flow action
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action reclassify
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-183 [002] b..1. 124.126477: netlink_extack: msg=act_gact: Offload of "reclassify" action is not supported
tc-183 [002] ..... 124.126489: netlink_extack: msg=cls_matchall: Failed to setup flow action
# tc filter add dev dummy0 ingress pref 1 proto all matchall skip_sw action pipe action drop
Error: cls_matchall: Failed to setup flow action.
We have an error talking to the kernel
# cat /sys/kernel/tracing/trace_pipe
tc-185 [002] b..1. 137.097791: netlink_extack: msg=act_gact: Offload of "pipe" action is not supported
tc-185 [002] ..... 137.097804: netlink_extack: msg=cls_matchall: Failed to setup flow action
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The callback is used by various actions to populate the flow action
structure prior to offload. Pass extack to this callback so that the
various actions will be able to report accurate error messages to user
space.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The verbose flag was added in commit 81c7288b170a ("sched: cls: enable
verbose logging") to avoid suppressing logging of error messages that
occur "when the rule is not to be exclusively executed by the hardware".
However, such error messages are currently suppressed when setup of flow
action fails. Take the verbose flag into account to avoid suppressing
error messages. This is done by using the extack pointer initialized by
tc_cls_common_offload_init(), which performs the necessary checks.
Before:
# tc filter add dev dummy0 ingress pref 1 proto ip flower dst_ip 198.51.100.1 action police rate 100Mbit burst 10000
# tc filter add dev dummy0 ingress pref 2 proto ip flower verbose dst_ip 198.51.100.1 action police rate 100Mbit burst 10000
After:
# tc filter add dev dummy0 ingress pref 1 proto ip flower dst_ip 198.51.100.1 action police rate 100Mbit burst 10000
# tc filter add dev dummy0 ingress pref 2 proto ip flower verbose dst_ip 198.51.100.1 action police rate 100Mbit burst 10000
Warning: cls_flower: Failed to setup flow action.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The verbose flag was added in commit 81c7288b170a ("sched: cls: enable
verbose logging") to avoid suppressing logging of error messages that
occur "when the rule is not to be exclusively executed by the hardware".
However, such error messages are currently suppressed when setup of flow
action fails. Take the verbose flag into account to avoid suppressing
error messages. This is done by using the extack pointer initialized by
tc_cls_common_offload_init(), which performs the necessary checks.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A tc flower filter matching TCA_FLOWER_KEY_VLAN_ETH_TYPE is expected to
match the L2 ethertype following the first VLAN header, as confirmed by
linked discussion with the maintainer. However, such rule also matches
packets that have additional second VLAN header, even though filter has
both eth_type and vlan_ethtype set to "ipv4". Looking at the code this
seems to be mostly an artifact of the way flower uses flow dissector.
First, even though looking at the uAPI eth_type and vlan_ethtype appear
like a distinct fields, in flower they are all mapped to the same
key->basic.n_proto. Second, flow dissector skips following VLAN header as
no keys for FLOW_DISSECTOR_KEY_CVLAN are set and eventually assigns the
value of n_proto to last parsed header. With these, such filters ignore any
headers present between first VLAN header and first "non magic"
header (ipv4 in this case) that doesn't result
FLOW_DISSECT_RET_PROTO_AGAIN.
Fix the issue by extending flow dissector VLAN key structure with new
'vlan_eth_type' field that matches first ethertype following previously
parsed VLAN header. Modify flower classifier to set the new
flow_dissector_key_vlan->vlan_eth_type with value obtained from
TCA_FLOWER_KEY_VLAN_ETH_TYPE/TCA_FLOWER_KEY_CVLAN_ETH_TYPE uAPIs.
Link: https://lore.kernel.org/all/Yjhgi48BpTGh6dig@nanopsycho/
Fixes: 9399ae9a6cb2 ("net_sched: flower: Add vlan support")
Fixes: d64efd0926ba ("net/sched: flower: Add supprt for matching on QinQ vlan headers")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When switching zones or network namespaces without doing a ct clear in
between, it is now leaking a reference to the old ct entry. That's
because tcf_ct_skb_nfct_cached() returns false and
tcf_ct_flow_table_lookup() may simply overwrite it.
The fix is to, as the ct entry is not reusable, free it already at
tcf_ct_skb_nfct_cached().
Reported-by: Florian Westphal <fw@strlen.de>
Fixes: 2f131de361f6 ("net/sched: act_ct: Fix flow table lookup after ct clear or switching zones")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Revert CHECKSUM_UNNECESSARY for UDP packet from conntrack.
2) Reject unsupported families when creating tables, from Phil Sutter.
3) GRE support for the flowtable, from Toshiaki Makita.
4) Add GRE offload support for act_ct, also from Toshiaki.
5) Update mlx5 driver to support for GRE flowtable offload,
from Toshiaki Makita.
6) Oneliner to clean up incorrect indentation in nf_conntrack_bridge,
from Jiapeng Chong.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: bridge: clean up some inconsistent indenting
net/mlx5: Support GRE conntrack offload
act_ct: Support GRE offload
netfilter: flowtable: Support GRE
netfilter: nf_tables: Reject tables of unsupported family
Revert "netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY"
====================
Link: https://lore.kernel.org/r/20220315091513.66544-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Options are as follows: PDU_TYPE:QFI and they refernce to
the fields from the PDU Session Protocol. PDU Session data
is conveyed in GTP-U Extension Header.
GTP-U Extension Header is described in 3GPP TS 29.281.
PDU Session Protocol is described in 3GPP TS 38.415.
PDU_TYPE - indicates the type of the PDU Session Information (4 bits)
QFI - QoS Flow Identifier (6 bits)
# ip link add gtp_dev type gtp role sgsn
# tc qdisc add dev gtp_dev ingress
# tc filter add dev gtp_dev protocol ip parent ffff: \
flower \
enc_key_id 11 \
gtp_opts 1:8/ff:ff \
action mirred egress redirect dev eth0
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
net/batman-adv/hard-interface.c
commit 690bb6fb64f5 ("batman-adv: Request iflink once in batadv-on-batadv check")
commit 6ee3c393eeb7 ("batman-adv: Demote batadv-on-batadv skip error message")
https://lore.kernel.org/all/20220302163049.101957-1-sw@simonwunderlich.de/
net/smc/af_smc.c
commit 4d08b7b57ece ("net/smc: Fix cleanup when register ULP fails")
commit 462791bbfa35 ("net/smc: add sysctl interface for SMC")
https://lore.kernel.org/all/20220302112209.355def40@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current tc-bpf@ingress reads and writes the __sk_buff->tstamp
as a (rcv) timestamp which currently could either be 0 (not available)
or ktime_get_real(). This patch is to backward compatible with the
(rcv) timestamp expectation at ingress. If the skb->tstamp has
the delivery_time, the bpf insn rewrite will read 0 for tc-bpf
running at ingress as it is not available. When writing at ingress,
it will also clear the skb->mono_delivery_time bit.
/* BPF_READ: a = __sk_buff->tstamp */
if (!skb->tc_at_ingress || !skb->mono_delivery_time)
a = skb->tstamp;
else
a = 0
/* BPF_WRITE: __sk_buff->tstamp = a */
if (skb->tc_at_ingress)
skb->mono_delivery_time = 0;
skb->tstamp = a;
[ A note on the BPF_CGROUP_INET_INGRESS which can also access
skb->tstamp. At that point, the skb is delivered locally
and skb_clear_delivery_time() has already been done,
so the skb->tstamp will only have the (rcv) timestamp. ]
If the tc-bpf@egress writes 0 to skb->tstamp, the skb->mono_delivery_time
has to be cleared also. It could be done together during
convert_ctx_access(). However, the latter patch will also expose
the skb->mono_delivery_time bit as __sk_buff->delivery_time_type.
Changing the delivery_time_type in the background may surprise
the user, e.g. the 2nd read on __sk_buff->delivery_time_type
may need a READ_ONCE() to avoid compiler optimization. Thus,
in expecting the needs in the latter patch, this patch does a
check on !skb->tstamp after running the tc-bpf and clears the
skb->mono_delivery_time bit if needed. The earlier discussion
on v4 [0].
The bpf insn rewrite requires the skb's mono_delivery_time bit and
tc_at_ingress bit. They are moved up in sk_buff so that bpf rewrite
can be done at a fixed offset. tc_skip_classify is moved together with
tc_at_ingress. To get one bit for mono_delivery_time, csum_not_inet is
moved down and this bit is currently used by sctp.
[0]: https://lore.kernel.org/bpf/20220217015043.khqwqklx45c4m4se@kafai-mbp.dhcp.thefacebook.com/
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support GREv0 without NAT.
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Acked-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add extack message to return exact message to user when adding invalid
filter with conflict flags for TC action.
In previous implement we just return EINVAL which is confusing for user.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Link: https://lore.kernel.org/r/1646191769-17761-1-git-send-email-baowen.zheng@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Use kfree_rcu(ptr, rcu) variant, using kfree_rcu(ptr) was not
intentional. From Eric Dumazet.
2) Use-after-free in netfilter hook core, from Eric Dumazet.
3) Missing rcu read lock side for netfilter egress hook,
from Florian Westphal.
4) nf_queue assume state->sk is full socket while it might not be.
Invoke sock_gen_put(), from Florian Westphal.
5) Add selftest to exercise the reported KASAN splat in 4)
6) Fix possible use-after-free in nf_queue in case sk_refcnt is 0.
Also from Florian.
7) Use input interface index only for hardware offload, not for
the software plane. This breaks tc ct action. Patch from Paul Blakey.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
net/sched: act_ct: Fix flow table lookup failure with no originating ifindex
netfilter: nf_queue: handle socket prefetch
netfilter: nf_queue: fix possible use-after-free
selftests: netfilter: add nfqueue TCP_NEW_SYN_RECV socket race test
netfilter: nf_queue: don't assume sk is full socket
netfilter: egress: silence egress hook lockdep splats
netfilter: fix use-after-free in __nf_register_net_hook()
netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
====================
Link: https://lore.kernel.org/r/20220301215337.378405-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After cited commit optimizted hw insertion, flow table entries are
populated with ifindex information which was intended to only be used
for HW offload. This tuple ifindex is hashed in the flow table key, so
it must be filled for lookup to be successful. But tuple ifindex is only
relevant for the netfilter flowtables (nft), so it's not filled in
act_ct flow table lookup, resulting in lookup failure, and no SW
offload and no offload teardown for TCP connection FIN/RST packets.
To fix this, add new tc ifindex field to tuple, which will
only be used for offloading, not for lookup, as it will not be
part of the tuple hash.
Fixes: 9795ded7f924 ("net/sched: act_ct: Fill offloading tuple iifidx")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The current police offload action entry is missing exceed/notexceed
actions and parameters that can be configured by tc police action.
Add the missing parameters as a pre-step for offloading police actions
to hardware.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/mptcp/mptcp_join.sh
34aa6e3bccd8 ("selftests: mptcp: add ip mptcp wrappers")
857898eb4b28 ("selftests: mptcp: add missing join check")
6ef84b1517e0 ("selftests: mptcp: more robust signal race test")
https://lore.kernel.org/all/20220221131842.468893-1-broonie@kernel.org/
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/act.h
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/ct.c
fb7e76ea3f3b6 ("net/mlx5e: TC, Skip redundant ct clear actions")
c63741b426e11 ("net/mlx5e: Fix MPLSoUDP encap to use MPLS action information")
09bf97923224f ("net/mlx5e: TC, Move pedit_headers_action to parse_attr")
84ba8062e383 ("net/mlx5e: Test CT and SAMPLE on flow attr")
efe6f961cd2e ("net/mlx5e: CT, Don't set flow flag CT for ct clear flow")
3b49a7edec1d ("net/mlx5e: TC, Reject rules with multiple CT actions")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
