| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
drivers/bluetooth/ath3k.c
drivers/bluetooth/btusb.c
|
|
Clear IEEE80211_STA_NULLFUNC_ACKED flag on disabling power
save. Without this fix, there is a chance of setting CONF_PS
before sending nullfunc frame.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"def_bool n" without prompt is pointless, this should be just "bool".
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The module parameter ieee80211_disable_40mhz_24ghz
was meant to allow disabling 40 MHz operation in
the 2.4 GHz band by default. However, it is buggy
as implemented because while it advertises to the
AP that the device doesn't support 40 MHz, it will
itself still use 40 MHz configurations.
To fix this, clear the 40 MHz bits from the sband
completely instead of overriding where used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-next-2.6
|
|
Low level driver could pass rx frames to us after disassociate, what
can lead to run conn_mon_timer by ieee80211_sta_rx_notify(). That
is obviously wrong, but nothing happens until we unload modules and
resources are used after free. If kernel debugging is enabled following
warning could be observed:
WARNING: at lib/debugobjects.c:259 debug_print_object+0x65/0x70()
Hardware name: HP xw8600 Workstation
ODEBUG: free active (active state 0) object type: timer_list
Modules linked in: iwlagn(-) iwlcore mac80211 cfg80211 aes_x86_64 aes_generic fuse cpufreq_ondemand acpi_cpufreq freq_table mperf xt_physdev ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ext3 jbd dm_mirror dm_region_hash dm_log dm_mod uinput hp_wmi sparse_keymap sg wmi arc4 microcode serio_raw ecb tg3 shpchp rfkill ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif firewire_ohci firewire_core crc_itu_t mptsas mptscsih mptbase scsi_transport_sas ahci libahci pata_acpi ata_generic ata_piix floppy nouveau ttm drm_kms_helper drm i2c_algo_bit i2c_core video [last unloaded: cfg80211]
Pid: 13827, comm: rmmod Tainted: G W 2.6.38-rc4-wl+ #22
Call Trace:
[<ffffffff810649cf>] ? warn_slowpath_common+0x7f/0xc0
[<ffffffff81064ac6>] ? warn_slowpath_fmt+0x46/0x50
[<ffffffff81226fc5>] ? debug_print_object+0x65/0x70
[<ffffffff81227625>] ? debug_check_no_obj_freed+0x125/0x210
[<ffffffff8109ebd7>] ? debug_check_no_locks_freed+0xf7/0x170
[<ffffffff81156092>] ? kfree+0xc2/0x2f0
[<ffffffff813ec5c5>] ? netdev_release+0x45/0x60
[<ffffffff812f1067>] ? device_release+0x27/0xa0
[<ffffffff81216ddd>] ? kobject_release+0x8d/0x1a0
[<ffffffff81216d50>] ? kobject_release+0x0/0x1a0
[<ffffffff812183b7>] ? kref_put+0x37/0x70
[<ffffffff81216c57>] ? kobject_put+0x27/0x60
[<ffffffff813d5d1b>] ? netdev_run_todo+0x1ab/0x270
[<ffffffff813e771e>] ? rtnl_unlock+0xe/0x10
[<ffffffffa0581188>] ? ieee80211_unregister_hw+0x58/0x120 [mac80211]
[<ffffffffa0377ed7>] ? iwl_pci_remove+0xdb/0x22a [iwlagn]
[<ffffffff8123cde2>] ? pci_device_remove+0x52/0x120
[<ffffffff812f5205>] ? __device_release_driver+0x75/0xe0
[<ffffffff812f5348>] ? driver_detach+0xd8/0xe0
[<ffffffff812f4111>] ? bus_remove_driver+0x91/0x100
[<ffffffff812f5b62>] ? driver_unregister+0x62/0xa0
[<ffffffff8123d194>] ? pci_unregister_driver+0x44/0xa0
[<ffffffffa0377df5>] ? iwl_exit+0x15/0x1c [iwlagn]
[<ffffffff810ab492>] ? sys_delete_module+0x1a2/0x270
[<ffffffff81498889>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff8100bf42>] ? system_call_fastpath+0x16/0x1b
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
As warned by checkpatch.pl, use #include <linux/uaccess.h> instead of
<asm/uaccess.h>.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
If the new connection update parameter are accepted, the LE master
host sends the LE Connection Update Command to its controller informing
the new requested parameters.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.
2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
If the fail happens the HCI del_timer may timeout after the the hci dev
unregister. This lead to a kernel crash.
Reported-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Implements L2CAP Connection Parameter Update Response defined in
the Bluetooth Core Specification, Volume 3, Part A, section 4.21.
Address the LE Connection Parameter Procedure initiated by the slave.
Connection Interval Minimum and Maximum have the same range: 6 to
3200. Time = N * 1.25ms. Minimum shall be less or equal to Maximum.
The Slave Latency field shall have a value in the range of 0 to
((connSupervisionTimeout / connIntervalMax) - 1). Latency field shall
be less than 500. connSupervisionTimeout = Timeout Multiplier * 10 ms.
Multiplier field shall have a value in the range of 10 to 3200.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch splits the L2CAP command handling function in order to
have a clear separation between the commands related to BR/EDR and
LE. Commands and responses in the LE signaling channel are not being
handled yet, command reject is sent to all received requests. Bluetooth
Core Specification, Volume 3, Part A, section 4 defines the signaling
packets formats and allowed commands/responses over the LE signaling
channel.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Separate LE and ACL timeouts. Othervise ACL connections
on non LE hw will time out after 45 secs.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Fix LE connections not being marked as master.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
l2cap over LE links can be disconnected without sending
disconnect command first.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Add support for LE server sockets.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Add basic LE connection support to L2CAP. LE
connection can be created by specifying cid
in struct sockaddr_l2
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Vladislav P <vladisslav@inbox.ru>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
l2cap_load() was added to trigger l2cap.ko module loading from the RFCOMM
and BNEP modules. Now that L2CAP module is gone, we don't need it anymore.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
WFA certification and the WMM spec require that we
always reply to unicast probe requests, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ieee80211_rx_h_check returned RX_DROP_MONITOR in case the if statement
in question was true but the same return value is also used directly
after the if clause. Hence, we can just drop the whole if clause and as
such simplify the code.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Actually doesn't make sense have these modules built separately.
The L2CAP layer is needed by almost all Bluetooth protocols and profiles.
There isn't any real use case without having L2CAP loaded.
SCO is only essential for Audio transfers, but it is so small that we can
have it loaded always in bluetooth.ko without problems.
If you really doesn't want it you can disable SCO in the kernel config.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
struct sco_conninfo has one padding byte in the end. Local variable
cinfo of type sco_conninfo is copied to userspace with this uninizialized
one byte, leading to old stack contents leak.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Struct ca is copied from userspace. It is not checked whether the "device"
field is NULL terminated. This potentially leads to BUG() inside of
alloc_netdev_mqs() and/or information leak by creating a device with a name
made of contents of kernel stack.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Structure l2cap_options has one padding byte between max_tx and
txwin_size fields. This byte in "opts" is copied to userspace
uninitialized.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
My previous patch to optimize scanning on operating channel
accidentally removed the code that would ensure power was
set to maximum for scanning.
This patch re-adds that functionality.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Narrow channel types can function within larger channel types.
So, use existing channel type for work items when possible.
This decreases hardware channel changes significantly when
using non NO_HT channel types on the operating channel.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Previous code set the channel type to NO_HT, but it
appears that NO_HT packets can be sent on any channel
type, so we do not need to change the channel type
as long as the channel is correct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some were indirectly set to NO_HT (zero), but I think
it's better to explicitly set it in case the enum ever
changes. In cfg.c, it seems the channel-type was just
ignored (and thus always set to NO_HT).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When suspending an associated system, and then resuming,
the station vif is being reconfigured without taking the
sdata->u.mgd.mtx lock, which results in the following warning:
WARNING: at net/mac80211/mlme.c:101 ieee80211_ap_probereq_get+0x58/0xb8 [mac80211]()
Modules linked in: wl12xx_sdio wl12xx firmware_class crc7 mac80211 cfg80211 [last unloaded: crc7]
Backtrace:
[<c005432c>] (dump_backtrace+0x0/0x118) from [<c0376e28>] (dump_stack+0x20/0x24)
r7:00000000 r6:bf12d6ec r5:bf154aac r4:00000065
[<c0376e08>] (dump_stack+0x0/0x24) from [<c0079104>] (warn_slowpath_common+0x5c/0x74)
[<c00790a8>] (warn_slowpath_common+0x0/0x74) from [<c0079148>] (warn_slowpath_null+0x2c/0x34)
r9:000024ff r8:cd006460 r7:00000001 r6:00000000 r5:00000000
r4:cf1394a0
[<c007911c>] (warn_slowpath_null+0x0/0x34) from [<bf12d6ec>] (ieee80211_ap_probereq_get+0x58/0xb8 [mac80211])
[<bf12d694>] (ieee80211_ap_probereq_get+0x0/0xb8 [mac80211]) from [<bf19cd04>] (wl1271_cmd_build_ap_probe_req+0x30/0xf8 [wl12xx])
r4:cd007440
[<bf19ccd4>] (wl1271_cmd_build_ap_probe_req+0x0/0xf8 [wl12xx]) from [<bf1995f4>] (wl1271_op_bss_info_changed+0x4c4/0x808 [wl12xx])
r5:cd007440 r4:000003b4
[<bf199130>] (wl1271_op_bss_info_changed+0x0/0x808 [wl12xx]) from [<bf122168>] (ieee80211_bss_info_change_notify+0x1a4/0x1f8 [mac80211])
[<bf121fc4>] (ieee80211_bss_info_change_notify+0x0/0x1f8 [mac80211]) from [<bf141e80>] (ieee80211_reconfig+0x4d0/0x668 [mac80211])
r8:cf0eeea4 r7:cd00671c r6:00000000 r5:cd006460 r4:cf1394a0
[<bf1419b0>] (ieee80211_reconfig+0x0/0x668 [mac80211]) from [<bf137dd4>] (ieee80211_resume+0x60/0x70 [mac80211])
[<bf137d74>] (ieee80211_resume+0x0/0x70 [mac80211]) from [<bf0eb930>] (wiphy_resume+0x6c/0x7c [cfg80211])
r5:cd006248 r4:cd006110
[<bf0eb8c4>] (wiphy_resume+0x0/0x7c [cfg80211]) from [<c0241024>] (legacy_resume+0x38/0x70)
r7:00000000 r6:00000000 r5:cd006248 r4:cd0062fc
[<c0240fec>] (legacy_resume+0x0/0x70) from [<c0241478>] (device_resume+0x168/0x1a0)
r8:c04ca8d8 r7:cd00627c r6:00000010 r5:cd006248 r4:cd0062fc
[<c0241310>] (device_resume+0x0/0x1a0) from [<c0241600>] (dpm_resume_end+0xf8/0x3bc)
r7:00000000 r6:00000005 r5:cd006248 r4:cd0062fc
[<c0241508>] (dpm_resume_end+0x0/0x3bc) from [<c00b2a24>] (suspend_devices_and_enter+0x1b0/0x204)
[<c00b2874>] (suspend_devices_and_enter+0x0/0x204) from [<c00b2b68>] (enter_state+0xf0/0x148)
r7:c037e978 r6:00000003 r5:c043d807 r4:00000000
[<c00b2a78>] (enter_state+0x0/0x148) from [<c00b20a4>] (state_store+0xa4/0xcc)
r7:c037e978 r6:00000003 r5:00000003 r4:c043d807
[<c00b2000>] (state_store+0x0/0xcc) from [<c01fc90c>] (kobj_attr_store+0x20/0x24)
[<c01fc8ec>] (kobj_attr_store+0x0/0x24) from [<c0157120>] (sysfs_write_file+0x11c/0x150)
[<c0157004>] (sysfs_write_file+0x0/0x150) from [<c0100f84>] (vfs_write+0xc0/0x14c)
[<c0100ec4>] (vfs_write+0x0/0x14c) from [<c01010e4>] (sys_write+0x4c/0x78)
r8:40126000 r7:00000004 r6:cf1a7c80 r5:00000000 r4:00000000
[<c0101098>] (sys_write+0x0/0x78) from [<c00500c0>] (ret_fast_syscall+0x0/0x30)
r8:c00502c8 r7:00000004 r6:403525e8 r5:40126000 r4:00000004
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
|
|
Change hcid to bluetoothd.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Also moves some L2CAP sending functions declaration to l2cap.h
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Declare __l2cap_wait_ack() and l2cap_sock_clear_timer() in l2cap.h
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
It causes the move of the declaration of 3 functions to l2cap.h:
l2cap_get_ident(), l2cap_send_cmd(), l2cap_build_conf_req()
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
