| Age | Commit message (Collapse) | Author |
|---|
|
af_iucv sockets over z/VM IUCV require that their skbs are allocated
in DMA memory. This restriction doesn't apply to connections over
HiperSockets. So only set this limit for z/VM IUCV sockets, thereby
increasing the likelihood that the large (and linear!) allocations for
HiperTransport messages succeed.
Fixes: 3881ac441f64 ("af_iucv: add HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Module autoload for masquerade and redirection does not work.
2) Leak in unqueued packets in nf_ct_frag6_queue(). Ignore duplicated
fragments, pretend they are placed into the queue. Patches from
Guillaume Nault.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, hvsock can enter into a state where epoll_wait on EPOLLOUT will
not return even when the hvsock socket is writable, under some race
condition. This can happen under the following sequence:
- fd = socket(hvsocket)
- fd_out = dup(fd)
- fd_in = dup(fd)
- start a writer thread that writes data to fd_out with a combination of
epoll_wait(fd_out, EPOLLOUT) and
- start a reader thread that reads data from fd_in with a combination of
epoll_wait(fd_in, EPOLLIN)
- On the host, there are two threads that are reading/writing data to the
hvsocket
stack:
hvs_stream_has_space
hvs_notify_poll_out
vsock_poll
sock_poll
ep_poll
Race condition:
check for epollout from ep_poll():
assume no writable space in the socket
hvs_stream_has_space() returns 0
check for epollin from ep_poll():
assume socket has some free space < HVS_PKT_LEN(HVS_SEND_BUF_SIZE)
hvs_stream_has_space() will clear the channel pending send size
host will not notify the guest because the pending send size has
been cleared and so the hvsocket will never mark the
socket writable
Now, the EPOLLOUT will never return even if the socket write buffer is
empty.
The fix is to set the pending size to the default size and never change it.
This way the host will always notify the guest whenever the writable space
is bigger than the pending size. The host is already optimized to *only*
notify the guest when the pending size threshold boundary is crossed and
not everytime.
This change also reduces the cpu usage somewhat since hv_stream_has_space()
is in the hotpath of send:
vsock_stream_sendmsg()->hv_stream_has_space()
Earlier hv_stream_has_space was setting/clearing the pending size on every
call.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes an issue where TX Timestamps are not arriving on the error queue
when UDP_SEGMENT CMSG type is combined with CMSG type SO_TIMESTAMPING.
This can be illustrated with an updated updgso_bench_tx program which
includes the '-T' option to test for this condition. It also introduces
the '-P' option which will call poll() before reading the error queue.
./udpgso_bench_tx -4ucTPv -S 1472 -l2 -D 172.16.120.18
poll timeout
udp tx: 0 MB/s 1 calls/s 1 msg/s
The "poll timeout" message above indicates that TX timestamp never
arrived.
This patch preserves tx_flags for the first UDP GSO segment. Only the
first segment is timestamped, even though in some cases there may be
benefital in timestamping both the first and last segment.
Factors in deciding on first segment timestamp only:
- Timestamping both first and last segmented is not feasible. Hardware
can only have one outstanding TS request at a time.
- Timestamping last segment may under report network latency of the
previous segments. Even though the doorbell is suppressed, the ring
producer counter has been incremented.
- Timestamping the first segment has the upside in that it reports
timestamps from the application's view, e.g. RTT.
- Timestamping the first segment has the downside that it may
underreport tx host network latency. It appears that we have to pick
one or the other. And possibly follow-up with a config flag to choose
behavior.
v2: Remove tests as noted by Willem de Bruijn <willemb@google.com>
Moving tests from net to net-next
v3: Update only relevant tx_flag bits as per
Willem de Bruijn <willemb@google.com>
v4: Update comments and commit message as per
Willem de Bruijn <willemb@google.com>
Fixes: ee80d1ebe5ba ("udp: add udp gso")
Signed-off-by: Fred Klassen <fklassen@appneta.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Brendan reports that the use of netem's packet corruption capability
leads to strange crashes. This seems to be caused by
commit d66280b12bd7 ("net: netem: use a list in addition to rbtree")
which uses skb->next pointer to construct a fast-path queue of
in-order skbs.
Packet corruption code has to invoke skb_gso_segment() in case
of skbs in need of GSO. skb_gso_segment() returns a list of
skbs. If next pointers of the skbs on that list do not get cleared
fast path list may point to freed skbs or skbs which are also on
the RB tree.
Let's say skb gets segmented into 3 frames:
A -> B -> C
A gets hooked to the t_head t_tail list by tfifo_enqueue(), but it's
next pointer didn't get cleared so we have:
h t
|/
A -> B -> C
Now if B and C get also get enqueued successfully all is fine, because
tfifo_enqueue() will overwrite the list in order. IOW:
Enqueue B:
h t
| |
A -> B C
Enqueue C:
h t
| |
A -> B -> C
But if B and C get reordered we may end up with:
h t RB tree
|/ |
A -> B -> C B
\
C
Or if they get dropped just:
h t
|/
A -> B -> C
where A and B are already freed.
To reproduce either limit has to be set low to cause freeing of
segs or reorders have to happen (due to delay jitter).
Note that we only have to mark the first segment as not on the
list, "finish_segs" handling of other frags already does that.
Another caveat is that qdisc_drop_all() still has to free all
segments correctly in case of drop of first segment, therefore
we re-link segs before calling it.
v2:
- re-link before drop, v1 was leaking non-first segs if limit
was hit at the first seg
- better commit message which lead to discovering the above :)
Reported-by: Brendan Galloway <brendan.galloway@netronome.com>
Fixes: d66280b12bd7 ("net: netem: use a list in addition to rbtree")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When GSO frame has to be corrupted netem uses skb_gso_segment()
to produce the list of frames, and re-enqueues the segments one
by one. The backlog length has to be adjusted to account for
new frames.
The current calculation is incorrect, leading to wrong backlog
lengths in the parent qdisc (both bytes and packets), and
incorrect packet backlog count in netem itself.
Parent backlog goes negative, netem's packet backlog counts
all non-first segments twice (thus remaining non-zero even
after qdisc is emptied).
Move the variables used to count the adjustment into local
scope to make 100% sure they aren't used at any stage in
backports.
Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
udp_tunnel(6)_xmit_skb() called by tipc_udp_xmit() expects a tunnel device
to count packets on dev->tstats, a perpcu variable. However, TIPC is using
udp tunnel with no tunnel device, and pass the lower dev, like veth device
that only initializes dev->lstats(a perpcu variable) when creating it.
Later iptunnel_xmit_stats() called by ip(6)tunnel_xmit() thinks the dev as
a tunnel device, and uses dev->tstats instead of dev->lstats. tstats' each
pointer points to a bigger struct than lstats, so when tstats->tx_bytes is
increased, other percpu variable's members could be overwritten.
syzbot has reported quite a few crashes due to fib_nh_common percpu member
'nhc_pcpu_rth_output' overwritten, call traces are like:
BUG: KASAN: slab-out-of-bounds in rt_cache_valid+0x158/0x190
net/ipv4/route.c:1556
rt_cache_valid+0x158/0x190 net/ipv4/route.c:1556
__mkroute_output net/ipv4/route.c:2332 [inline]
ip_route_output_key_hash_rcu+0x819/0x2d50 net/ipv4/route.c:2564
ip_route_output_key_hash+0x1ef/0x360 net/ipv4/route.c:2393
__ip_route_output_key include/net/route.h:125 [inline]
ip_route_output_flow+0x28/0xc0 net/ipv4/route.c:2651
ip_route_output_key include/net/route.h:135 [inline]
...
or:
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:dst_dev_put+0x24/0x290 net/core/dst.c:168
<IRQ>
rt_fibinfo_free_cpus net/ipv4/fib_semantics.c:200 [inline]
free_fib_info_rcu+0x2e1/0x490 net/ipv4/fib_semantics.c:217
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2437 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2716 [inline]
rcu_process_callbacks+0x100a/0x1ac0 kernel/rcu/tree.c:2697
...
The issue exists since tunnel stats update is moved to iptunnel_xmit by
Commit 039f50629b7f ("ip_tunnel: Move stats update to iptunnel_xmit()"),
and here to fix it by passing a NULL tunnel dev to udp_tunnel(6)_xmit_skb
so that the packets counting won't happen on dev->tstats.
Reported-by: syzbot+9d4c12bfd45a58738d0a@syzkaller.appspotmail.com
Reported-by: syzbot+a9e23ea2aa21044c2798@syzkaller.appspotmail.com
Reported-by: syzbot+c4c4b2bb358bb936ad7e@syzkaller.appspotmail.com
Reported-by: syzbot+0290d2290a607e035ba1@syzkaller.appspotmail.com
Reported-by: syzbot+a43d8d4e7e8a7a9e149e@syzkaller.appspotmail.com
Reported-by: syzbot+a47c5f4c6c00fc1ed16e@syzkaller.appspotmail.com
Fixes: 039f50629b7f ("ip_tunnel: Move stats update to iptunnel_xmit()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
iptunnel_xmit() works as a common function, also used by a udp tunnel
which doesn't have to have a tunnel device, like how TIPC works with
udp media.
In these cases, we should allow not to count pkts on dev's tstats, so
that udp tunnel can work with no tunnel device safely.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In sock_getsockopt(), 'optlen' is fetched the first time from userspace.
'len < 0' is then checked. Then in condition 'SO_MEMINFO', 'optlen' is
fetched the second time from userspace.
If change it between two fetches may cause security problems or unexpected
behaivor, and there is no reason to fetch it a second time.
To fix this, we need to remove the second fetch.
Signed-off-by: JingYi Hou <houjingyi647@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It appears that a FAILOVER_MSG can come from peer even when the failure
link is resetting (i.e. just after the 'node_write_unlock()'...). This
means the failover procedure on the node has not been started yet.
The situation is as follows:
node1 node2
linkb linka linka linkb
| | | |
| | x failure |
| | RESETTING |
| | | |
| x failure RESET |
| RESETTING FAILINGOVER |
| | (FAILOVER_MSG) | |
|<-------------------------------------------------|
| *FAILINGOVER | | |
| | (dummy FAILOVER_MSG) | |
|------------------------------------------------->|
| RESET | | FAILOVER_END
| FAILINGOVER RESET |
. . . .
. . . .
. . . .
Once this happens, the link failover procedure will be triggered
wrongly on the receiving node since the node isn't in FAILINGOVER state
but then another link failover will be carried out.
The consequences are:
1) A peer might get stuck in FAILINGOVER state because the 'sync_point'
was set, reset and set incorrectly, the criteria to end the failover
would not be met, it could keep waiting for a message that has already
received.
2) The early FAILOVER_MSG(s) could be queued in the link failover
deferdq but would be purged or not pulled out because the 'drop_point'
was not set correctly.
3) The early FAILOVER_MSG(s) could be dropped too.
4) The dummy FAILOVER_MSG could make the peer leaving FAILINGOVER state
shortly, but later on it would be restarted.
The same situation can also happen when the link is in PEER_RESET state
and a FAILOVER_MSG arrives.
The commit resolves the issues by forcing the link down immediately, so
the failover procedure will be started normally (which is the same as
when receiving a FAILOVER_MSG and the link is in up state).
Also, the function "tipc_node_link_failover()" is toughen to avoid such
a situation from happening.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
|
|
Eric Dumazet says:
====================
tcp: make sack processing more robust
Jonathan Looney brought to our attention multiple problems
in TCP stack at the sender side.
SACK processing can be abused by malicious peers to either
cause overflows, or increase of memory usage.
First two patches fix the immediate problems.
Since the malicious peers abuse senders by advertizing a very
small MSS in their SYN or SYNACK packet, the last two
patches add a new sysctl so that admins can chose a higher
limit for MSS clamping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lapb_register calls lapb_create_cb, which initializes the control-
block's ref-count to one, and __lapb_insert_cb, which increments it when
adding the new block to the list of blocks.
lapb_unregister calls __lapb_remove_cb, which decrements the ref-count
when removing control-block from the list of blocks, and calls lapb_put
itself to decrement the ref-count before returning.
However, lapb_unregister also calls __lapb_devtostruct to look up the
right control-block for the given net_device, and __lapb_devtostruct
also bumps the ref-count, which means that when lapb_unregister returns
the ref-count is still 1 and the control-block is leaked.
Call lapb_put after __lapb_devtostruct to fix leak.
Reported-by: syzbot+afb980676c836b4a0afa@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c93 ("tipc: guarantee group unicast doesn't bypass group broadcast")
Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before thread in process context uses bh_lock_sock()
we must disable bh.
sysbot reported :
WARNING: inconsistent lock state
5.2.0-rc3+ #32 Not tainted
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
blkid/26581 [HC0[0]:SC1[1]:HE1:SE0] takes:
00000000e0da85ee (slock-AF_AX25){+.?.}, at: spin_lock include/linux/spinlock.h:338 [inline]
00000000e0da85ee (slock-AF_AX25){+.?.}, at: ax25_destroy_timer+0x53/0xc0 net/ax25/af_ax25.c:275
{SOFTIRQ-ON-W} state was registered at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4303
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
spin_lock include/linux/spinlock.h:338 [inline]
ax25_rt_autobind+0x3ca/0x720 net/ax25/ax25_route.c:429
ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1221
__sys_connect+0x264/0x330 net/socket.c:1834
__do_sys_connect net/socket.c:1845 [inline]
__se_sys_connect net/socket.c:1842 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1842
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
irq event stamp: 2272
hardirqs last enabled at (2272): [<ffffffff810065f3>] trace_hardirqs_on_thunk+0x1a/0x1c
hardirqs last disabled at (2271): [<ffffffff8100660f>] trace_hardirqs_off_thunk+0x1a/0x1c
softirqs last enabled at (1522): [<ffffffff87400654>] __do_softirq+0x654/0x94c kernel/softirq.c:320
softirqs last disabled at (2267): [<ffffffff81449010>] invoke_softirq kernel/softirq.c:374 [inline]
softirqs last disabled at (2267): [<ffffffff81449010>] irq_exit+0x180/0x1d0 kernel/softirq.c:414
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(slock-AF_AX25);
<Interrupt>
lock(slock-AF_AX25);
*** DEADLOCK ***
1 lock held by blkid/26581:
#0: 0000000010fd154d ((&ax25->dtimer)){+.-.}, at: lockdep_copy_map include/linux/lockdep.h:175 [inline]
#0: 0000000010fd154d ((&ax25->dtimer)){+.-.}, at: call_timer_fn+0xe0/0x720 kernel/time/timer.c:1312
stack backtrace:
CPU: 1 PID: 26581 Comm: blkid Not tainted 5.2.0-rc3+ #32
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_usage_bug.cold+0x393/0x4a2 kernel/locking/lockdep.c:2935
valid_state kernel/locking/lockdep.c:2948 [inline]
mark_lock_irq kernel/locking/lockdep.c:3138 [inline]
mark_lock+0xd46/0x1370 kernel/locking/lockdep.c:3513
mark_irqflags kernel/locking/lockdep.c:3391 [inline]
__lock_acquire+0x159f/0x5490 kernel/locking/lockdep.c:3745
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4303
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
spin_lock include/linux/spinlock.h:338 [inline]
ax25_destroy_timer+0x53/0xc0 net/ax25/af_ax25.c:275
call_timer_fn+0x193/0x720 kernel/time/timer.c:1322
expire_timers kernel/time/timer.c:1366 [inline]
__run_timers kernel/time/timer.c:1685 [inline]
__run_timers kernel/time/timer.c:1653 [inline]
run_timer_softirq+0x66f/0x1740 kernel/time/timer.c:1698
__do_softirq+0x25c/0x94c kernel/softirq.c:293
invoke_softirq kernel/softirq.c:374 [inline]
irq_exit+0x180/0x1d0 kernel/softirq.c:414
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0x13b/0x550 arch/x86/kernel/apic/apic.c:1068
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:806
</IRQ>
RIP: 0033:0x7f858d5c3232
Code: 8b 61 08 48 8b 84 24 d8 00 00 00 4c 89 44 24 28 48 8b ac 24 d0 00 00 00 4c 8b b4 24 e8 00 00 00 48 89 7c 24 68 48 89 4c 24 78 <48> 89 44 24 58 8b 84 24 e0 00 00 00 89 84 24 84 00 00 00 8b 84 24
RSP: 002b:00007ffcaf0cf5c0 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13
RAX: 00007f858d7d27a8 RBX: 00007f858d7d8820 RCX: 00007f858d3940d8
RDX: 00007ffcaf0cf798 RSI: 00000000f5e616f3 RDI: 00007f858d394fee
RBP: 0000000000000000 R08: 00007ffcaf0cf780 R09: 00007f858d7db480
R10: 0000000000000000 R11: 0000000009691a75 R12: 0000000000000005
R13: 00000000f5e616f3 R14: 0000000000000000 R15: 00007ffcaf0cf798
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nine years ago, I added RCU handling to neighbours, not pneighbours.
(pneigh are not commonly used)
Unfortunately I missed that /proc dump operations would use a
common entry and exit point : neigh_seq_start() and neigh_seq_stop()
We need to read_lock(tbl->lock) or risk use-after-free while
iterating the pneigh structures.
We might later convert pneigh to RCU and revert this patch.
sysbot reported :
BUG: KASAN: use-after-free in pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158
Read of size 8 at addr ffff888097f2a700 by task syz-executor.0/9825
CPU: 1 PID: 9825 Comm: syz-executor.0 Not tainted 5.2.0-rc4+ #32
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188
__kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
kasan_report+0x12/0x20 mm/kasan/common.c:614
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158
neigh_seq_next+0xdb/0x210 net/core/neighbour.c:3240
seq_read+0x9cf/0x1110 fs/seq_file.c:258
proc_reg_read+0x1fc/0x2c0 fs/proc/inode.c:221
do_loop_readv_writev fs/read_write.c:714 [inline]
do_loop_readv_writev fs/read_write.c:701 [inline]
do_iter_read+0x4a4/0x660 fs/read_write.c:935
vfs_readv+0xf0/0x160 fs/read_write.c:997
kernel_readv fs/splice.c:359 [inline]
default_file_splice_read+0x475/0x890 fs/splice.c:414
do_splice_to+0x127/0x180 fs/splice.c:877
splice_direct_to_actor+0x2d2/0x970 fs/splice.c:954
do_splice_direct+0x1da/0x2a0 fs/splice.c:1063
do_sendfile+0x597/0xd00 fs/read_write.c:1464
__do_sys_sendfile64 fs/read_write.c:1525 [inline]
__se_sys_sendfile64 fs/read_write.c:1511 [inline]
__x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4592c9
Code: fd b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f4aab51dc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028
RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00000000004592c9
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000005
RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000080000000 R11: 0000000000000246 R12: 00007f4aab51e6d4
R13: 00000000004c689d R14: 00000000004db828 R15: 00000000ffffffff
Allocated by task 9827:
save_stack+0x23/0x90 mm/kasan/common.c:71
set_track mm/kasan/common.c:79 [inline]
__kasan_kmalloc mm/kasan/common.c:489 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462
kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503
__do_kmalloc mm/slab.c:3660 [inline]
__kmalloc+0x15c/0x740 mm/slab.c:3669
kmalloc include/linux/slab.h:552 [inline]
pneigh_lookup+0x19c/0x4a0 net/core/neighbour.c:731
arp_req_set_public net/ipv4/arp.c:1010 [inline]
arp_req_set+0x613/0x720 net/ipv4/arp.c:1026
arp_ioctl+0x652/0x7f0 net/ipv4/arp.c:1226
inet_ioctl+0x2a0/0x340 net/ipv4/af_inet.c:926
sock_do_ioctl+0xd8/0x2f0 net/socket.c:1043
sock_ioctl+0x3ed/0x780 net/socket.c:1194
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xd5f/0x1380 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 9824:
save_stack+0x23/0x90 mm/kasan/common.c:71
set_track mm/kasan/common.c:79 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:451
kasan_slab_free+0xe/0x10 mm/kasan/common.c:459
__cache_free mm/slab.c:3432 [inline]
kfree+0xcf/0x220 mm/slab.c:3755
pneigh_ifdown_and_unlock net/core/neighbour.c:812 [inline]
__neigh_ifdown+0x236/0x2f0 net/core/neighbour.c:356
neigh_ifdown+0x20/0x30 net/core/neighbour.c:372
arp_ifdown+0x1d/0x21 net/ipv4/arp.c:1274
inetdev_destroy net/ipv4/devinet.c:319 [inline]
inetdev_event+0xa14/0x11f0 net/ipv4/devinet.c:1544
notifier_call_chain+0xc2/0x230 kernel/notifier.c:95
__raw_notifier_call_chain kernel/notifier.c:396 [inline]
raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:403
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1749
call_netdevice_notifiers_extack net/core/dev.c:1761 [inline]
call_netdevice_notifiers net/core/dev.c:1775 [inline]
rollback_registered_many+0x9b9/0xfc0 net/core/dev.c:8178
rollback_registered+0x109/0x1d0 net/core/dev.c:8220
unregister_netdevice_queue net/core/dev.c:9267 [inline]
unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9260
unregister_netdevice include/linux/netdevice.h:2631 [inline]
__tun_detach+0xd8a/0x1040 drivers/net/tun.c:724
tun_detach drivers/net/tun.c:741 [inline]
tun_chr_close+0xe0/0x180 drivers/net/tun.c:3451
__fput+0x2ff/0x890 fs/file_table.c:280
____fput+0x16/0x20 fs/file_table.c:313
task_work_run+0x145/0x1c0 kernel/task_work.c:113
tracehook_notify_resume include/linux/tracehook.h:185 [inline]
exit_to_usermode_loop+0x273/0x2c0 arch/x86/entry/common.c:168
prepare_exit_to_usermode arch/x86/entry/common.c:199 [inline]
syscall_return_slowpath arch/x86/entry/common.c:279 [inline]
do_syscall_64+0x58e/0x680 arch/x86/entry/common.c:304
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff888097f2a700
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes inside of
64-byte region [ffff888097f2a700, ffff888097f2a740)
The buggy address belongs to the page:
page:ffffea00025fca80 refcount:1 mapcount:0 mapping:ffff8880aa400340 index:0x0
flags: 0x1fffc0000000200(slab)
raw: 01fffc0000000200 ffffea000250d548 ffffea00025726c8 ffff8880aa400340
raw: 0000000000000000 ffff888097f2a000 0000000100000020 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888097f2a600: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
ffff888097f2a680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888097f2a700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ffff888097f2a780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888097f2a800: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_tx_skb_cache_key and tcp_rx_skb_cache_key must be available
even if CONFIG_SYSCTL is not set.
Fixes: 0b7d7f6b2208 ("tcp: add tcp_tx_skb_cache sysctl")
Fixes: ede61ca474a0 ("tcp: add tcp_rx_skb_cache sysctl")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc 8.2.0 may report these bogus warnings under some condition:
warning: ‘vnew’ may be used uninitialized in this function
warning: ‘hvs_new’ may be used uninitialized in this function
Actually, the 2 pointers are only initialized and used if the variable
"conn_from_host" is true. The code is not buggy here.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When stack receives pkt: [802.1P vlan 0][802.1AD vlan 100][IPv4],
vlan_do_receive() returns false if it does not find vlan_dev. Later
__netif_receive_skb_core() fails to find packet type handler for
skb->protocol 801.1AD and drops the packet.
801.1P header with vlan id 0 should be handled as untagged packets.
This patch fixes it by checking if vlan_id is 0 and processes next vlan
header.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mtu probing is enabled tcp_mtu_probing() could very well end up
with a too small MSS.
Use the new sysctl tcp_min_snd_mss to make sure MSS search
is performed in an acceptable range.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f118 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jonathan Looney reported that a malicious peer can force a sender
to fragment its retransmit queue into tiny skbs, inflating memory
usage and/or overflow 32bit counters.
TCP allows an application to queue up to sk_sndbuf bytes,
so we need to give some allowance for non malicious splitting
of retransmit queue.
A new SNMP counter is added to monitor how many times TCP
did not allow to split an skb if the allowance was exceeded.
Note that this counter might increase in the case applications
use SO_SNDBUF socket option to lower sk_sndbuf.
CVE-2019-11478 : tcp_fragment, prevent fragmenting a packet when the
socket is already using more than half the allowed space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jonathan Looney reported that TCP can trigger the following crash
in tcp_shifted_skb() :
BUG_ON(tcp_skb_pcount(skb) < pcount);
This can happen if the remote peer has advertized the smallest
MSS that linux TCP accepts : 48
An skb can hold 17 fragments, and each fragment can hold 32KB
on x86, or 64KB on PowerPC.
This means that the 16bit witdh of TCP_SKB_CB(skb)->tcp_gso_segs
can overflow.
Note that tcp_sendmsg() builds skbs with less than 64KB
of payload, so this problem needs SACK to be enabled.
SACK blocks allow TCP to coalesce multiple skbs in the retransmit
queue, thus filling the 17 fragments to maximal capacity.
CVE-2019-11477 -- u16 overflow of TCP_SKB_CB(skb)->tcp_gso_segs
Fixes: 832d11c5cd07 ("tcp: Try to restore large SKBs while SACK processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2019-06-15
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix stack layout of JITed x64 bpf code, from Alexei.
2) fix out of bounds memory access in bpf_sk_storage, from Arthur.
3) fix lpm trie walk, from Jonathan.
4) fix nested bpf_perf_event_output, from Matt.
5) and several other fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpf_sk_storage maps use multiple spin locks to reduce contention.
The number of locks to use is determined by the number of possible CPUs.
With only 1 possible CPU, bucket_log == 0, and 2^0 = 1 locks are used.
When updating elements, the correct lock is determined with hash_ptr().
Calling hash_ptr() with 0 bits is undefined behavior, as it does:
x >> (64 - bits)
Using the value results in an out of bounds memory access.
In my case, this manifested itself as a page fault when raw_spin_lock_bh()
is called later, when running the self tests:
./tools/testing/selftests/bpf/test_verifier 773 775
[ 16.366342] BUG: unable to handle page fault for address: ffff8fe7a66f93f8
Force the minimum number of locks to two.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Fixes: 6ac99e8f23d4 ("bpf: Introduce bpf sk local storage")
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Set the SOCK_DONE flag to match the TCP_CLOSING state when a peer has
shut down and there is nothing left to read.
This fixes the following bug:
1) Peer sends SHUTDOWN(RDWR).
2) Socket enters TCP_CLOSING but SOCK_DONE is not set.
3) read() returns -ENOTCONN until close() is called, then returns 0.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From linux-3.7, (commit 5640f7685831 "net: use a per task frag
allocator") TCP sendmsg() has preferred using order-3 allocations.
While it gives good results for most cases, we had reports
that heavy uses of TCP over loopback were hitting a spinlock
contention in page allocations/freeing.
This commits adds a sysctl so that admins can opt-in
for order-0 allocations. Hopefully mm layer might optimize
order-3 allocations in the future since it could give us
a nice boost (see 8 lines of following benchmark)
The following benchmark shows a win when more than 8 TCP_STREAM
threads are running (56 x86 cores server in my tests)
for thr in {1..30}
do
sysctl -wq net.core.high_order_alloc_disable=0
T0=`./super_netperf $thr -H 127.0.0.1 -l 15`
sysctl -wq net.core.high_order_alloc_disable=1
T1=`./super_netperf $thr -H 127.0.0.1 -l 15`
echo $thr:$T0:$T1
done
1: 49979: 37267
2: 98745: 76286
3: 141088: 110051
4: 177414: 144772
5: 197587: 173563
6: 215377: 208448
7: 241061: 234087
8: 267155: 263373
9: 295069: 297402
10: 312393: 335213
11: 340462: 368778
12: 371366: 403954
13: 412344: 443713
14: 426617: 473580
15: 474418: 507861
16: 503261: 538539
17: 522331: 563096
18: 532409: 567084
19: 550824: 605240
20: 525493: 641988
21: 564574: 665843
22: 567349: 690868
23: 583846: 710917
24: 588715: 736306
25: 603212: 763494
26: 604083: 792654
27: 602241: 796450
28: 604291: 797993
29: 611610: 833249
30: 577356: 841062
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Feng Tang reported a performance regression after introduction
of per TCP socket tx/rx caches, for TCP over loopback (netperf)
There is high chance the regression is caused by a change on
how well the 32 KB per-thread page (current->task_frag) can
be recycled, and lack of pcp caches for order-3 pages.
I could not reproduce the regression myself, cpus all being
spinning on the mm spinlocks for page allocs/freeing, regardless
of enabling or disabling the per tcp socket caches.
It seems best to disable the feature by default, and let
admins enabling it.
MM layer either needs to provide scalable order-3 pages
allocations, or could attempt a trylock on zone->lock if
the caller only attempts to get a high-order page and is
able to fallback to order-0 ones in case of pressure.
Tests run on a 56 cores host (112 hyper threads)
- 35.49% netperf [kernel.vmlinux] [k] queued_spin_lock_slowpath
- 35.49% queued_spin_lock_slowpath
- 18.18% get_page_from_freelist
- __alloc_pages_nodemask
- 18.18% alloc_pages_current
skb_page_frag_refill
sk_page_frag_refill
tcp_sendmsg_locked
tcp_sendmsg
inet_sendmsg
sock_sendmsg
__sys_sendto
__x64_sys_sendto
do_syscall_64
entry_SYSCALL_64_after_hwframe
__libc_send
+ 17.31% __free_pages_ok
+ 31.43% swapper [kernel.vmlinux] [k] intel_idle
+ 9.12% netperf [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 6.53% netserver [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 0.69% netserver [kernel.vmlinux] [k] queued_spin_lock_slowpath
+ 0.68% netperf [kernel.vmlinux] [k] skb_release_data
+ 0.52% netperf [kernel.vmlinux] [k] tcp_sendmsg_locked
0.46% netperf [kernel.vmlinux] [k] _raw_spin_lock_irqsave
Fixes: 472c2e07eef0 ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current flower mask creating code assumes that temporary mask that is used
when inserting new filter is stack allocated. To prevent race condition
with data patch synchronize_rcu() is called every time fl_create_new_mask()
replaces temporary stack allocated mask. As reported by Jiri, this
increases runtime of creating 20000 flower classifiers from 4 seconds to
163 seconds. However, this design is no longer necessary since temporary
mask was converted to be dynamically allocated by commit 2cddd2014782
("net/sched: cls_flower: allocate mask dynamically in fl_change()").
Remove synchronize_rcu() calls from mask creation code. Instead, refactor
fl_change() to always deallocate temporary mask with rcu grace period.
Fixes: 195c234d15c9 ("net: sched: flower: handle concurrent mask insertion")
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on comments from Xin, even after fixes for our recent syzbot
report of cookie memory leaks, its possible to get a resend of an INIT
chunk which would lead to us leaking cookie memory.
To ensure that we don't leak cookie memory, free any previously
allocated cookie first.
Change notes
v1->v2
update subsystem tag in subject (davem)
repeat kfree check for peer_random and peer_hmacs (xin)
v2->v3
net->sctp
also free peer_chunks
v3->v4
fix subject tags
v4->v5
remove cut line
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: Xin Long <lucien.xin@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check that the NFC_ATTR_TARGET_INDEX attributes (in addition to
NFC_ATTR_DEVICE_INDEX) are provided by the netlink client prior to
accessing them. This prevents potential unhandled NULL pointer dereference
exceptions which can be triggered by malicious user-mode programs,
if they omit one or both of these attributes.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of reporting the AP's TSF, host time was reported. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In wiphy_new_nm(), if an error occurs after dev_set_name() and
device_initialize() have already been called, it's necessary to call
put_device() (via wiphy_free()) to avoid a memory leak.
Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com
Fixes: 1f87f7d3a3b4 ("cfg80211: add rfkill support")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The bits of Rx MCS Map in VHT capability were enumerated
with index transform - index i -> (i + 1) bit => nss i. BUG!
while it should be - index i -> (i + 1) bit => (i + 1) nss.
The bug was exposed in commit a53b2a0b1245 ("iwlwifi: mvm: implement VHT
extended NSS support in rs.c"), where iwlwifi started using the
function.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: b0aa75f0b1b2 ("ieee80211: add new VHT capability fields/parsing")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It is not a good idea to try to perform any work (e.g. send an auth
frame) during reconfigure flow.
Prevent this from happening, and at the end of the reconfigure flow
requeue all the works.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The seen_indices variable is u64 and in other parts of the code we
assume mbssid_index_ie[2] can be up to 45, so we should use the 64-bit
versions of BIT, namely, BIT_ULL().
Reported-by: Dan Carpented <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In multiple SSID cases, it takes time to prepare every AP interface
to be ready in initializing phase. If a sta already knows everything it
needs to join one of the APs and sends authentication to the AP which
is not fully prepared at this point of time, AP's channel context
could be NULL. As a result, warning message occurs.
Even worse, if the AP is under attack via tools such as MDK3 and massive
authentication requests are received in a very short time, console will
be hung due to kernel warning messages.
WARN_ON_ONCE() could be a better way for indicating warning messages
without duplicate messages to flood the console.
Johannes: We still need to address the underlying problem, but we
don't really have a good handle on it yet. Suppress the
worst side-effects for now.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
[johannes: add note, change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When receiving a robust management frame, drop it if we don't have
rx->sta since then we don't have a security association and thus
couldn't possibly validate the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
tls_sw_do_sendpage needs to return the total number of bytes sent
regardless of how many sk_msgs are allocated. Unfortunately, copied
(the value we return up the stack) is zero'd before each new sk_msg
is allocated so we only return the copied size of the last sk_msg used.
The caller (splice, etc.) of sendpage will then believe only part
of its data was sent and send the missing chunks again. However,
because the data actually was sent the receiver will get multiple
copies of the same data.
To reproduce this do multiple sendfile calls with a length close to
the max record size. This will in turn call splice/sendpage, sendpage
may use multiple sk_msg in this case and then returns the incorrect
number of bytes. This will cause splice to resend creating duplicate
data on the receiver. Andre created a C program that can easily
generate this case so we will push a similar selftest for this to
bpf-next shortly.
The fix is to _not_ zero the copied field so that the total sent
bytes is returned.
Reported-by: Steinar H. Gunderson <steinar+kernel@gunderson.no>
Reported-by: Andre Tomt <andre@tomt.net>
Tested-by: Andre Tomt <andre@tomt.net>
Fixes: d829e9c4112b ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get the ingress interface and increment ICMP counters based on that
instead of skb->dev when the the dev is a VRF device.
This is a follow up on the following message:
https://www.spinics.net/lists/netdev/msg560268.html
v2: Avoid changing skb->dev since it has unintended effect for local
delivery (David Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using ethtool, users can specify a classification action matching on the
full vlan tag, which includes the DEI bit (also previously called CFI).
However, when converting the ethool_flow_spec to a flow_rule, we use
dissector keys to represent the matching patterns.
Since the vlan dissector key doesn't include the DEI bit, this
information was silently discarded when translating the ethtool
flow spec in to a flow_rule.
This commit adds the DEI bit into the vlan dissector key, and allows
propagating the information to the driver when parsing the ethtool flow
spec.
Fixes: eca4205f9ec3 ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Randy reported that selecting MPLS_ROUTING without PROC_FS breaks
the build, because since commit c1a9d65954c6 ("mpls: fix af_mpls
dependencies"), MPLS_ROUTING selects PROC_SYSCTL, but Kconfig's select
doesn't recursively handle dependencies.
Change the select into a dependency.
Fixes: c1a9d65954c6 ("mpls: fix af_mpls dependencies")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not call 'ndo_bpf()' or 'dev_put()' with NULL argument.
Fixes: c9b47cc1fabc ("xsk: fix bug when trying to use both copy and zero-copy on one queue id")
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The cloned sk should not carry its parent-listener's sk_bpf_storage.
This patch fixes it by setting it back to NULL.
Fixes: 6ac99e8f23d4 ("bpf: Introduce bpf sk local storage")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In order to create an internal vport, internal_dev_create() is used and
that calls register_netdevice() internally.
If register_netdevice() fails, it calls dev->priv_destructor() to free
private data of netdev. actually, a private data of this is a vport.
Hence internal_dev_create() should not free and use a vport after failure
of register_netdevice().
Test command
ovs-dpctl add-dp bonding_masters
Splat looks like:
[ 1035.667767] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 1035.675958] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 1035.676916] CPU: 1 PID: 1028 Comm: ovs-vswitchd Tainted: G B 5.2.0-rc3+ #240
[ 1035.676916] RIP: 0010:internal_dev_create+0x2e5/0x4e0 [openvswitch]
[ 1035.676916] Code: 48 c1 ea 03 80 3c 02 00 0f 85 9f 01 00 00 4c 8b 23 48 b8 00 00 00 00 00 fc ff df 49 8d bc 24 60 05 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 86 01 00 00 49 8b bc 24 60 05 00 00 e8 e4 68 f4
[ 1035.713720] RSP: 0018:ffff88810dcb7578 EFLAGS: 00010206
[ 1035.713720] RAX: dffffc0000000000 RBX: ffff88810d13fe08 RCX: ffffffff84297704
[ 1035.713720] RDX: 00000000000000ac RSI: 0000000000000000 RDI: 0000000000000560
[ 1035.713720] RBP: 00000000ffffffef R08: fffffbfff0d3b881 R09: fffffbfff0d3b881
[ 1035.713720] R10: 0000000000000001 R11: fffffbfff0d3b880 R12: 0000000000000000
[ 1035.768776] R13: 0000607ee460b900 R14: ffff88810dcb7690 R15: ffff88810dcb7698
[ 1035.777709] FS: 00007f02095fc980(0000) GS:ffff88811b400000(0000) knlGS:0000000000000000
[ 1035.777709] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1035.777709] CR2: 00007ffdf01d2f28 CR3: 0000000108258000 CR4: 00000000001006e0
[ 1035.777709] Call Trace:
[ 1035.777709] ovs_vport_add+0x267/0x4f0 [openvswitch]
[ 1035.777709] new_vport+0x15/0x1e0 [openvswitch]
[ 1035.777709] ovs_vport_cmd_new+0x567/0xd10 [openvswitch]
[ 1035.777709] ? ovs_dp_cmd_dump+0x490/0x490 [openvswitch]
[ 1035.777709] ? __kmalloc+0x131/0x2e0
[ 1035.777709] ? genl_family_rcv_msg+0xa54/0x1030
[ 1035.777709] genl_family_rcv_msg+0x63a/0x1030
[ 1035.777709] ? genl_unregister_family+0x630/0x630
[ 1035.841681] ? debug_show_all_locks+0x2d0/0x2d0
[ ... ]
Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The below patch fixes an incorrect zerocopy refcnt increment when
appending with MSG_MORE to an existing zerocopy udp skb.
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt 1
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt still 1 (bar frags)
But it missed that zerocopy need not be passed at the first send. The
right test whether the uarg is newly allocated and thus has extra
refcnt 1 is not !skb, but !skb_zcopy.
send(.., MSG_MORE); // <no uarg>
send(.., MSG_ZEROCOPY); // refcnt 1
Fixes: 100f6d8e09905 ("net: correct zerocopy refcnt with udp MSG_MORE")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 794200d66273 ("tcp: undo cwnd on Fast Open spurious SYNACK
retransmit") may cause tcp_fastretrans_alert() to warn about pending
retransmission in Open state. This is triggered when the Fast Open
server both sends data and has spurious SYNACK retransmission during
the handshake, and the data packets were lost or reordered.
The root cause is a bit complicated:
(1) Upon receiving SYN-data: a full socket is created with
snd_una = ISN + 1 by tcp_create_openreq_child()
(2) On SYNACK timeout the server/sender enters CA_Loss state.
(3) Upon receiving the final ACK to complete the handshake, sender
does not mark FLAG_SND_UNA_ADVANCED since (1)
Sender then calls tcp_process_loss since state is CA_loss by (2)
(4) tcp_process_loss() does not invoke undo operations but instead
mark REXMIT_LOST to force retransmission
(5) tcp_rcv_synrecv_state_fastopen() calls tcp_try_undo_loss(). It
changes state to CA_Open but has positive tp->retrans_out
(6) Next ACK triggers the WARN_ON in tcp_fastretrans_alert()
The step that goes wrong is (4) where the undo operation should
have been invoked because the ACK successfully acknowledged the
SYN sequence. This fixes that by specifically checking undo
when the SYN-ACK sequence is acknowledged. Then after
tcp_process_loss() the state would be further adjusted based
in tcp_fastretrans_alert() to avoid triggering the warning in (6).
Fixes: 794200d66273 ("tcp: undo cwnd on Fast Open spurious SYNACK retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPLS routing code relies on sysctl to work, so let it select PROC_SYSCTL.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
