From 6eb583da959cf751eb951cc5ff488dd4e41f1b2f Mon Sep 17 00:00:00 2001
From: Sivaram Nair
Date: Tue, 20 Nov 2012 09:29:16 +0200
Subject: ARM: tegra: select correct parent clk for pll_p

For Tegra30, pll_p clk's parent is wrongly specified as clk_m instead of
pll_ref in the tegra30_clk_init_table and this is resulting in a
boot-time warning. This patch fixes this by correcting the clk init
table.

Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
---
 arch/arm/mach-tegra/common.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-tegra/common.c b/arch/arm/mach-tegra/common.c
index 0b0a5f556d34..988549a77b69 100644
--- a/arch/arm/mach-tegra/common.c
+++ b/arch/arm/mach-tegra/common.c
@@ -102,7 +102,7 @@ static __initdata struct tegra_clk_init_table tegra20_clk_init_table[] = {
 static __initdata struct tegra_clk_init_table tegra30_clk_init_table[] = {
 	/* name		parent		rate		enabled */
 	{ "clk_m",	NULL,		0,		true },
-	{ "pll_p",	"clk_m",	408000000,	true },
+	{ "pll_p",	"pll_ref",	408000000,	true },
 	{ "pll_p_out1",	"pll_p",	9600000,	true },
 	{ NULL,		NULL,		0,		0},
 };
-- 
cgit v1.2.3


From 6e25e1b178ee3caf34f229bacfad5ae6780bcec6 Mon Sep 17 00:00:00 2001
From: Sivaram Nair
Date: Wed, 21 Nov 2012 13:42:27 +0200
Subject: ARM: tegra: fix comment in dsib clk set_parent

Since the clk framework has already taken necessary locks before calling
into the arch clk ops code, no further locks are needed while setting
the parent of dsib clk. This patch removes a comment that indicated
otherwise, and yet did not take any locks.

Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
---
 arch/arm/mach-tegra/tegra30_clocks.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/arm/mach-tegra/tegra30_clocks.c b/arch/arm/mach-tegra/tegra30_clocks.c
index e9de5dfd94ec..c2102a312bc5 100644
--- a/arch/arm/mach-tegra/tegra30_clocks.c
+++ b/arch/arm/mach-tegra/tegra30_clocks.c
@@ -1913,9 +1913,7 @@ struct clk_ops tegra30_periph_clk_ops = {
 static int tegra30_dsib_clk_set_parent(struct clk_hw *hw, u8 index)
 {
 	struct clk *d = clk_get_sys(NULL, "pll_d");
-	/* The DSIB parent selection bit is in PLLD base
-	   register - can not do direct r-m-w, must be
-	   protected by PLLD lock */
+	/* The DSIB parent selection bit is in PLLD base register */
 	tegra_clk_cfg_ex(
 		d, TEGRA_CLK_PLLD_MIPI_MUX_SEL, index);
 
-- 
cgit v1.2.3


From f110174910896b7a7d91c0c60d19136815f68c54 Mon Sep 17 00:00:00 2001
From: Hiroshi Doyu
Date: Wed, 21 Nov 2012 14:41:37 +0200
Subject: amba: tegra-ahb: Fix warning w/o PM_SLEEP

Fix build warning w/o PM_SLEEP.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
---
 drivers/amba/tegra-ahb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/amba/tegra-ahb.c b/drivers/amba/tegra-ahb.c
index 0b6f0b28a487..ce8fdadf3696 100644
--- a/drivers/amba/tegra-ahb.c
+++ b/drivers/amba/tegra-ahb.c
@@ -156,6 +156,7 @@ int tegra_ahb_enable_smmu(struct device_node *dn)
 EXPORT_SYMBOL(tegra_ahb_enable_smmu);
 #endif
 
+#ifdef CONFIG_PM_SLEEP
 static int tegra_ahb_suspend(struct device *dev)
 {
 	int i;
@@ -175,6 +176,7 @@ static int tegra_ahb_resume(struct device *dev)
 		gizmo_writel(ahb, ahb->ctx[i], tegra_ahb_gizmo[i]);
 	return 0;
 }
+#endif
 
 static UNIVERSAL_DEV_PM_OPS(tegra_ahb_pm,
 			    tegra_ahb_suspend,
-- 
cgit v1.2.3


From 210dce5faf89c9677ac1a6273bc53f130843539f Mon Sep 17 00:00:00 2001
From: Florian Fainelli
Date: Mon, 10 Dec 2012 22:21:19 +0100
Subject: ARM: ep93xx: properly wait for UART FIFO to be empty

This patch changes the busy-waiting loop around in the decompressor
putc() function on the UART FIFO register. Without a proper wait, the
output of the decompressor was corrupted like this:

Uncompressing Linx. done, booting th enl

To highlight the issue more evidently, looping 100 times instead of 1000
makes the issue appear much faster. This patch takes the approach of
using an active while loop until the FIFO is empty (not FULL).
This issue happened to me on Sim.One running at 200Mhz.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
---
 arch/arm/mach-ep93xx/include/mach/uncompress.h | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/arch/arm/mach-ep93xx/include/mach/uncompress.h b/arch/arm/mach-ep93xx/include/mach/uncompress.h
index 16026c2b1c8c..d64274fc5760 100644
--- a/arch/arm/mach-ep93xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ep93xx/include/mach/uncompress.h
@@ -47,13 +47,9 @@ static void __raw_writel(unsigned int value, unsigned int ptr)
 
 static inline void putc(int c)
 {
-	int i;
-
-	for (i = 0; i < 1000; i++) {
-		/* Transmit fifo not full?  */
-		if (!(__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF))
-			break;
-	}
+	/* Transmit fifo not full?  */
+	while (__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF)
+		;
 
 	__raw_writeb(c, PHYS_UART_DATA);
 }
-- 
cgit v1.2.3


From 34cceb7464f2db0da4da900afa82a210f4470b89 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Tue, 27 Nov 2012 11:22:39 -0600
Subject: ARM: OMAP2+: Fix realtime_counter_init warning in timer.c

In commit fa6d79d (ARM: OMAP: Add initialisation for the real-time
counter), the function realtime_counter_init() was added. However, if
the kernel configuration option CONFIG_SOC_OMAP5 is not selected then
the following compiler warning is observed.

  CC      arch/arm/mach-omap2/timer.o
  arch/arm/mach-omap2/timer.c:489:20: warning: ‘realtime_counter_init’
  defined but not used [-Wunused-function]

Commit fa6d79d also introduced the kernel configuration option
CONFIG_SOC_HAS_REALTIME_COUNTER. If this option is not selected then the
a stub function for realtime_counter_init() is defined.

For non-OMAP5 devices, there is no realtime counter and so
realtime_counter_init() function and stub function are not used for
these devices. Therefore, fix this warning by only allowing the kernel
configuration option CONFIG_SOC_HAS_REALTIME_COUNTER to be enabled for
OMAP5 devices.

Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by Santosh Shilimkar <santosh.shilimkar@ti.com>
---
 arch/arm/mach-omap2/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index be0f62bf9037..41b581fd0213 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -26,6 +26,8 @@ config SOC_HAS_OMAP2_SDRC
 
 config SOC_HAS_REALTIME_COUNTER
 	bool "Real time free running counter"
+	depends on SOC_OMAP5
+	default y
 
 config ARCH_OMAP2
 	bool "TI OMAP2"
@@ -79,7 +81,6 @@ config SOC_OMAP5
 	select ARM_GIC
 	select CPU_V7
 	select HAVE_SMP
-	select SOC_HAS_REALTIME_COUNTER
 	select COMMON_CLK
 
 comment "OMAP Core Type"
-- 
cgit v1.2.3


From e0c3e27ce19fcc81156ba49c91d83a676144a103 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Tue, 27 Nov 2012 15:24:12 -0600
Subject: ARM: AM335x: Fix warning in timer.c

When compiling the kernel with configuration options ...

 # CONFIG_ARCH_OMAP2 is not set
 # CONFIG_ARCH_OMAP3 is not set
 # CONFIG_ARCH_OMAP4 is not set
 # CONFIG_SOC_OMAP5 is not set
 CONFIG_SOC_AM33XX=y

 ... the following build warning is seen.

  CC      arch/arm/mach-omap2/timer.o
  arch/arm/mach-omap2/timer.c:395:19: warning: ‘omap2_sync32k_clocksource_init’
  	defined but not used [-Wunused-function]

This issue was introduced by commit 6f80b3b (ARM: OMAP2+: timer: remove
CONFIG_OMAP_32K_TIMER) where the omap2_sync32k_clocksource_init() is no
longer referenced by the timer initialisation function for the AM335x
device as it has no 32k-sync timer.

Fix this by adding the "__maybe_unused" compiler directive to the
omap2_sync32k_clocksource_init() function to indicate that this function
may be used for certain configurations.

Cc: Igor Grinberg <grinberg@compulab.co.il>

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
---
 arch/arm/mach-omap2/timer.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index 7016637b531c..e2ffe0adc28b 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -392,7 +392,7 @@ static struct of_device_id omap_counter_match[] __initdata = {
 };
 
 /* Setup free-running counter for clocksource */
-static int __init omap2_sync32k_clocksource_init(void)
+static int __init __maybe_unused omap2_sync32k_clocksource_init(void)
 {
 	int ret;
 	struct device_node *np = NULL;
-- 
cgit v1.2.3


From bf85f205d95eb223e849914101e0db1a5a576a3c Mon Sep 17 00:00:00 2001
From: Vaibhav Hiremath
Date: Wed, 28 Nov 2012 15:56:41 -0600
Subject: ARM: OMAP2+: Fix sparse warnings in timer.c

Sparse generates the following warnings when compiling mach-omap2/timer.c.

  CHECK   arch/arm/mach-omap2/timer.c
  arch/arm/mach-omap2/timer.c:193:13: warning: symbol 'omap_dmtimer_init'
  was not declared. Should it be static?
  arch/arm/mach-omap2/timer.c:213:12: warning: symbol
  'omap_dm_timer_get_errata' was not declared. Should it be static?

Add static to function declaration to fix warnings.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
---
 arch/arm/mach-omap2/timer.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index e2ffe0adc28b..06e141543623 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -190,7 +190,7 @@ static struct device_node * __init omap_get_timer_dt(struct of_device_id *match,
  * kernel registering these devices remove them dynamically from the device
  * tree on boot.
  */
-void __init omap_dmtimer_init(void)
+static void __init omap_dmtimer_init(void)
 {
 	struct device_node *np;
 
@@ -210,7 +210,7 @@ void __init omap_dmtimer_init(void)
  *
  * Get the timer errata flags that are specific to the OMAP device being used.
  */
-u32 __init omap_dm_timer_get_errata(void)
+static u32 __init omap_dm_timer_get_errata(void)
 {
 	if (cpu_is_omap24xx())
 		return 0;
-- 
cgit v1.2.3


From ca2e16faa7378878c1522a7c1b6c38211de3331d Mon Sep 17 00:00:00 2001
From: Tomi Valkeinen
Date: Thu, 22 Nov 2012 10:39:56 +0200
Subject: OMAP: board-files: fix i2c_bus for tfp410

The i2c handling in tfp410 driver, which handles converting parallel RGB
to DVI, was changed in 958f2717b84e88bf833d996997fda8f73276f2af
(OMAPDSS: TFP410: pdata rewrite). The patch changed what value the
driver considers as invalid/undefined.  Before the patch, 0 was the
invalid value, but as 0 is a valid bus number, the patch changed this to
-1.

However, the fact was missed that many board files do not define the bus
number at all, thus it's left to 0. This causes the driver to fail to
get the i2c bus, exiting from the driver's probe with an error, meaning
that the DVI output does not work for those boards.

This patch fixes the issue by changing the i2c_bus number field in the
driver's platform data from u16 to int, and setting the bus number to -1
in the board files for the boards that did not define the bus. The
exception is devkit8000, for which the bus is set to 1, which is the
correct bus for that board.

The bug exists in v3.5+ kernels.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Thomas Weber <thomas@tomweber.eu>
Cc: Thomas Weber <thomas@tomweber.eu>
Cc: <stable@vger.kernel.org> # v3.5+
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-3430sdp.c      | 1 +
 arch/arm/mach-omap2/board-am3517evm.c    | 1 +
 arch/arm/mach-omap2/board-cm-t35.c       | 1 +
 arch/arm/mach-omap2/board-devkit8000.c   | 1 +
 arch/arm/mach-omap2/board-omap3evm.c     | 1 +
 arch/arm/mach-omap2/board-omap3stalker.c | 1 +
 include/video/omap-panel-tfp410.h        | 2 +-
 7 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 7b201546834d..bb73afc9ac17 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -157,6 +157,7 @@ static struct omap_dss_device sdp3430_lcd_device = {
 
 static struct tfp410_platform_data dvi_panel = {
 	.power_down_gpio	= -1,
+	.i2c_bus_num		= -1,
 };
 
 static struct omap_dss_device sdp3430_dvi_device = {
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 4be58fd071f6..f81a303b87ff 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -208,6 +208,7 @@ static struct omap_dss_device am3517_evm_tv_device = {
 
 static struct tfp410_platform_data dvi_panel = {
 	.power_down_gpio	= -1,
+	.i2c_bus_num		= -1,
 };
 
 static struct omap_dss_device am3517_evm_dvi_device = {
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index c8e37dc00892..b3102c2f4a3c 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -241,6 +241,7 @@ static struct omap_dss_device cm_t35_lcd_device = {
 
 static struct tfp410_platform_data dvi_panel = {
 	.power_down_gpio	= CM_T35_DVI_EN_GPIO,
+	.i2c_bus_num		= -1,
 };
 
 static struct omap_dss_device cm_t35_dvi_device = {
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 7667eb749522..12865af25d3a 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -141,6 +141,7 @@ static struct omap_dss_device devkit8000_lcd_device = {
 
 static struct tfp410_platform_data dvi_panel = {
 	.power_down_gpio	= -1,
+	.i2c_bus_num		= 1,
 };
 
 static struct omap_dss_device devkit8000_dvi_device = {
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 54647d6286b4..3985f35aee06 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -240,6 +240,7 @@ static struct omap_dss_device omap3_evm_tv_device = {
 
 static struct tfp410_platform_data dvi_panel = {
 	.power_down_gpio	= OMAP3EVM_DVI_PANEL_EN_GPIO,
+	.i2c_bus_num		= -1,
 };
 
 static struct omap_dss_device omap3_evm_dvi_device = {
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
index d8638b3b4f94..53a6cbcf9747 100644
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ b/arch/arm/mach-omap2/board-omap3stalker.c
@@ -118,6 +118,7 @@ static struct omap_dss_device omap3_stalker_tv_device = {
 
 static struct tfp410_platform_data dvi_panel = {
 	.power_down_gpio	= DSS_ENABLE_GPIO,
+	.i2c_bus_num		= -1,
 };
 
 static struct omap_dss_device omap3_stalker_dvi_device = {
diff --git a/include/video/omap-panel-tfp410.h b/include/video/omap-panel-tfp410.h
index 68c31d79c571..aef35e48bc7e 100644
--- a/include/video/omap-panel-tfp410.h
+++ b/include/video/omap-panel-tfp410.h
@@ -28,7 +28,7 @@ struct omap_dss_device;
  * @power_down_gpio: gpio number for PD pin (or -1 if not available)
  */
 struct tfp410_platform_data {
-	u16 i2c_bus_num;
+	int i2c_bus_num;
 	int power_down_gpio;
 };
 
-- 
cgit v1.2.3


From 421e84509980206fb3b3bc039bc05bae1dd41c7b Mon Sep 17 00:00:00 2001
From: Oleg Matcovschi
Date: Mon, 26 Nov 2012 17:02:03 -0800
Subject: OMAP2+: mux: Fixed gpio mux mode analysis

OMAP_MODE_GPIO() macro verified only OMAP_MUX_MODE4.
It is not correct for following platforms:
    2430 - gpio mux mode 3
    44xx - gpio mux mode 3
    54xx - gpio mux mode 6

Patch reserves first 3 bits in partition flags for storing gpio mux
mode in same format as stored in control pad register.
Modified OMAP_MODE_GPIO() macro to handle all possible cases of gpio mux mode.
Modified omap_mux_init() flags of omap34xx to include OMAP_MUX_GPIO_IN_MODE4.

Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/mux.c     | 10 ++++------
 arch/arm/mach-omap2/mux.h     | 20 +++++++++++++++-----
 arch/arm/mach-omap2/mux34xx.c |  2 +-
 3 files changed, 20 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 26126343d6ac..6a217c98db54 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -135,10 +135,7 @@ static int __init _omap_mux_init_gpio(struct omap_mux_partition *partition,
 
 	old_mode = omap_mux_read(partition, gpio_mux->reg_offset);
 	mux_mode = val & ~(OMAP_MUX_NR_MODES - 1);
-	if (partition->flags & OMAP_MUX_GPIO_IN_MODE3)
-		mux_mode |= OMAP_MUX_MODE3;
-	else
-		mux_mode |= OMAP_MUX_MODE4;
+	mux_mode |= partition->gpio;
 	pr_debug("%s: Setting signal %s.gpio%i 0x%04x -> 0x%04x\n", __func__,
 		 gpio_mux->muxnames[0], gpio, old_mode, mux_mode);
 	omap_mux_write(partition, mux_mode, gpio_mux->reg_offset);
@@ -800,7 +797,7 @@ int __init omap_mux_late_init(void)
 			struct omap_mux *m = &e->mux;
 			u16 mode = omap_mux_read(partition, m->reg_offset);
 
-			if (OMAP_MODE_GPIO(mode))
+			if (OMAP_MODE_GPIO(partition, mode))
 				continue;
 
 #ifndef CONFIG_DEBUG_FS
@@ -1065,7 +1062,7 @@ static void __init omap_mux_init_list(struct omap_mux_partition *partition,
 		}
 #else
 		/* Skip pins that are not muxed as GPIO by bootloader */
-		if (!OMAP_MODE_GPIO(omap_mux_read(partition,
+		if (!OMAP_MODE_GPIO(partition, omap_mux_read(partition,
 				    superset->reg_offset))) {
 			superset++;
 			continue;
@@ -1132,6 +1129,7 @@ int __init omap_mux_init(const char *name, u32 flags,
 
 	partition->name = name;
 	partition->flags = flags;
+	partition->gpio = flags & OMAP_MUX_MODE7;
 	partition->size = mux_size;
 	partition->phys = mux_pbase;
 	partition->base = ioremap(mux_pbase, mux_size);
diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h
index 76f9b3c2f586..fdb22f14021f 100644
--- a/arch/arm/mach-omap2/mux.h
+++ b/arch/arm/mach-omap2/mux.h
@@ -58,7 +58,8 @@
 #define OMAP_PIN_OFF_INPUT_PULLDOWN	(OMAP_OFF_EN | OMAP_OFF_PULL_EN)
 #define OMAP_PIN_OFF_WAKEUPENABLE	OMAP_WAKEUP_EN
 
-#define OMAP_MODE_GPIO(x)	(((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE4)
+#define OMAP_MODE_GPIO(partition, x)	(((x) & OMAP_MUX_MODE7) == \
+					  partition->gpio)
 #define OMAP_MODE_UART(x)	(((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE0)
 
 /* Flags for omapX_mux_init */
@@ -79,13 +80,20 @@
 /*
  * omap_mux_init flags definition:
  *
+ * OMAP_GPIO_MUX_MODE, bits 0-2: gpio muxing mode, same like pad control
+ *      register which includes values from 0-7.
  * OMAP_MUX_REG_8BIT: Ensure that access to padconf is done in 8 bits.
  * The default value is 16 bits.
- * OMAP_MUX_GPIO_IN_MODE3: The GPIO is selected in mode3.
- * The default is mode4.
  */
-#define OMAP_MUX_REG_8BIT		(1 << 0)
-#define OMAP_MUX_GPIO_IN_MODE3		(1 << 1)
+#define OMAP_MUX_GPIO_IN_MODE0		OMAP_MUX_MODE0
+#define OMAP_MUX_GPIO_IN_MODE1		OMAP_MUX_MODE1
+#define OMAP_MUX_GPIO_IN_MODE2		OMAP_MUX_MODE2
+#define OMAP_MUX_GPIO_IN_MODE3		OMAP_MUX_MODE3
+#define OMAP_MUX_GPIO_IN_MODE4		OMAP_MUX_MODE4
+#define OMAP_MUX_GPIO_IN_MODE5		OMAP_MUX_MODE5
+#define OMAP_MUX_GPIO_IN_MODE6		OMAP_MUX_MODE6
+#define OMAP_MUX_GPIO_IN_MODE7		OMAP_MUX_MODE7
+#define OMAP_MUX_REG_8BIT		(1 << 3)
 
 /**
  * struct omap_board_data - board specific device data
@@ -105,6 +113,7 @@ struct omap_board_data {
  * struct mux_partition - contain partition related information
  * @name: name of the current partition
  * @flags: flags specific to this partition
+ * @gpio: gpio mux mode
  * @phys: physical address
  * @size: partition size
  * @base: virtual address after ioremap
@@ -114,6 +123,7 @@ struct omap_board_data {
 struct omap_mux_partition {
 	const char		*name;
 	u32			flags;
+	u32			gpio;
 	u32			phys;
 	u32			size;
 	void __iomem		*base;
diff --git a/arch/arm/mach-omap2/mux34xx.c b/arch/arm/mach-omap2/mux34xx.c
index c47140bbbec4..c53609f46294 100644
--- a/arch/arm/mach-omap2/mux34xx.c
+++ b/arch/arm/mach-omap2/mux34xx.c
@@ -2053,7 +2053,7 @@ int __init omap3_mux_init(struct omap_board_mux *board_subset, int flags)
 		return -EINVAL;
 	}
 
-	return omap_mux_init("core", 0,
+	return omap_mux_init("core", OMAP_MUX_GPIO_IN_MODE4,
 			     OMAP3_CONTROL_PADCONF_MUX_PBASE,
 			     OMAP3_CONTROL_PADCONF_MUX_SIZE,
 			     omap3_muxmodes, package_subset, board_subset,
-- 
cgit v1.2.3


From 86c35960852b726a1d773ae65302dcfb24267180 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Tue, 13 Nov 2012 16:02:19 -0600
Subject: ARM: OMAP2420: Fix ethernet support for OMAP2420 H4

Ethernet is not currently working on the OMAP2420 H4 board. In commit
f604931 (ARM: OMAP: abstract debug card setup (smc, leds)) the function
h4_init_smc91x() that initialised the ethernet controller was renamed to
h4_init_debug() but was never called when initialising the board.

Adding a call to h4_init_debug() fixes ethernet support, however,
instead of using the legacy H4 code migrate the H4 to use the
gpmc_smc91x_init() function instead and remove the legacy H4 code.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-h4.c | 83 ++++++++++--------------------------------
 1 file changed, 20 insertions(+), 63 deletions(-)

diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index 9a3878ec2256..3be1311f9e33 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -27,14 +27,12 @@
 #include <linux/io.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/mfd/menelaus.h>
+#include <linux/omap-dma.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <linux/omap-dma.h>
-#include <plat/debug-devices.h>
-
 #include <video/omapdss.h>
 #include <video/omap-panel-generic-dpi.h>
 
@@ -42,11 +40,9 @@
 #include "mux.h"
 #include "control.h"
 #include "gpmc.h"
+#include "gpmc-smc91x.h"
 
 #define H4_FLASH_CS	0
-#define H4_SMC91X_CS	1
-
-#define H4_ETHR_GPIO_IRQ		92
 
 #if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
 static const uint32_t board_matrix_keys[] = {
@@ -250,71 +246,31 @@ static u32 is_gpmc_muxed(void)
 		return 0;
 }
 
-static inline void __init h4_init_debug(void)
-{
-	int eth_cs;
-	unsigned long cs_mem_base;
-	unsigned int muxed, rate;
-	struct clk *gpmc_fck;
-
-	eth_cs	= H4_SMC91X_CS;
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91x_MODULE)
 
-	gpmc_fck = clk_get(NULL, "gpmc_fck");	/* Always on ENABLE_ON_INIT */
-	if (IS_ERR(gpmc_fck)) {
-		WARN_ON(1);
-		return;
-	}
-
-	clk_prepare_enable(gpmc_fck);
-	rate = clk_get_rate(gpmc_fck);
-	clk_disable_unprepare(gpmc_fck);
-	clk_put(gpmc_fck);
+static struct omap_smc91x_platform_data board_smc91x_data = {
+	.cs		= 1,
+	.gpio_irq	= 92,
+	.flags		= GPMC_TIMINGS_SMC91C96 | IORESOURCE_IRQ_LOWLEVEL,
+};
 
+static void __init board_smc91x_init(void)
+{
 	if (is_gpmc_muxed())
-		muxed = 0x200;
-	else
-		muxed = 0;
-
-	/* Make sure CS1 timings are correct */
-	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1,
-			  0x00011000 | muxed);
-
-	if (rate >= 160000000) {
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
-	} else if (rate >= 130000000) {
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
-	} else {/* rate = 100000000 */
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
-	}
-
-	if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
-		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
-		goto out;
-	}
+		board_smc91x_data.flags |= GPMC_MUX_ADD_DATA;
 
-	udelay(100);
+	omap_mux_init_gpio(board_smc91x_data.gpio_irq, OMAP_PIN_INPUT);
+	gpmc_smc91x_init(&board_smc91x_data);
+}
 
-	omap_mux_init_gpio(92, 0);
-	if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
-		gpmc_cs_free(eth_cs);
+#else
 
-out:
-	clk_disable_unprepare(gpmc_fck);
-	clk_put(gpmc_fck);
+static inline void board_smc91x_init(void)
+{
 }
 
+#endif
+
 static void __init h4_init_flash(void)
 {
 	unsigned long base;
@@ -371,6 +327,7 @@ static void __init omap_h4_init(void)
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	h4_init_flash();
+	board_smc91x_init();
 
 	omap_display_init(&h4_dss_data);
 }
-- 
cgit v1.2.3


From 657b9deeed33cfb6f7171361accc6982727d2e0b Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Tue, 13 Nov 2012 16:02:20 -0600
Subject: ARM: OMAP: Remove debug-devices.c

The OMAP2420 H4 board was the only board using the
plat-omap/debug-devices.c code for configuring ethernet support. Now
that OMAP2420 H4 has been migrated to use the generic gpmc code for
configuring ethernet support, the debug-devices.c file is no longer
used and so remove it and its header file.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/Makefile                     |  1 -
 arch/arm/plat-omap/debug-devices.c              | 92 -------------------------
 arch/arm/plat-omap/include/plat/debug-devices.h |  2 -
 3 files changed, 95 deletions(-)
 delete mode 100644 arch/arm/plat-omap/debug-devices.c
 delete mode 100644 arch/arm/plat-omap/include/plat/debug-devices.h

diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile
index 8d885848600a..9d9aa2f55129 100644
--- a/arch/arm/plat-omap/Makefile
+++ b/arch/arm/plat-omap/Makefile
@@ -11,7 +11,6 @@ obj-  :=
 # omap_device support (OMAP2+ only at the moment)
 
 obj-$(CONFIG_OMAP_DM_TIMER) += dmtimer.o
-obj-$(CONFIG_OMAP_DEBUG_DEVICES) += debug-devices.o
 obj-$(CONFIG_OMAP_DEBUG_LEDS) += debug-leds.o
 i2c-omap-$(CONFIG_I2C_OMAP) := i2c.o
 obj-y += $(i2c-omap-m) $(i2c-omap-y)
diff --git a/arch/arm/plat-omap/debug-devices.c b/arch/arm/plat-omap/debug-devices.c
deleted file mode 100644
index a609e2161817..000000000000
--- a/arch/arm/plat-omap/debug-devices.c
+++ /dev/null
@@ -1,92 +0,0 @@
-/*
- * linux/arch/arm/plat-omap/debug-devices.c
- *
- * Copyright (C) 2005 Nokia Corporation
- * Modified from mach-omap2/board-h4.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/smc91x.h>
-
-#include <plat/debug-devices.h>
-
-/* Many OMAP development platforms reuse the same "debug board"; these
- * platforms include H2, H3, H4, and Perseus2.
- */
-
-static struct smc91x_platdata smc91x_info = {
-	.flags	= SMC91X_USE_16BIT | SMC91X_NOWAIT,
-	.leda	= RPC_LED_100_10,
-	.ledb	= RPC_LED_TX_RX,
-};
-
-static struct resource smc91x_resources[] = {
-	[0] = {
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
-	},
-};
-
-static struct platform_device smc91x_device = {
-	.name		= "smc91x",
-	.id		= -1,
-	.dev		= {
-		.platform_data = &smc91x_info,
-	},
-	.num_resources	= ARRAY_SIZE(smc91x_resources),
-	.resource	= smc91x_resources,
-};
-
-static struct resource led_resources[] = {
-	[0] = {
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device led_device = {
-	.name		= "omap_dbg_led",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(led_resources),
-	.resource	= led_resources,
-};
-
-static struct platform_device *debug_devices[] __initdata = {
-	&smc91x_device,
-	&led_device,
-	/* ps2 kbd + mouse ports */
-	/* 4 extra uarts */
-	/* 6 input dip switches */
-	/* 8 output pins */
-};
-
-int __init debug_card_init(u32 addr, unsigned gpio)
-{
-	int	status;
-
-	smc91x_resources[0].start = addr + 0x300;
-	smc91x_resources[0].end   = addr + 0x30f;
-
-	smc91x_resources[1].start = gpio_to_irq(gpio);
-	smc91x_resources[1].end   = gpio_to_irq(gpio);
-
-	status = gpio_request(gpio, "SMC91x irq");
-	if (status < 0) {
-		printk(KERN_ERR "GPIO%d unavailable for smc91x IRQ\n", gpio);
-		return status;
-	}
-	gpio_direction_input(gpio);
-
-	led_resources[0].start = addr;
-	led_resources[0].end   = addr + SZ_4K - 1;
-
-	return platform_add_devices(debug_devices, ARRAY_SIZE(debug_devices));
-}
diff --git a/arch/arm/plat-omap/include/plat/debug-devices.h b/arch/arm/plat-omap/include/plat/debug-devices.h
deleted file mode 100644
index 8fc4287222dd..000000000000
--- a/arch/arm/plat-omap/include/plat/debug-devices.h
+++ /dev/null
@@ -1,2 +0,0 @@
-/* for TI reference platforms sharing the same debug card */
-extern int debug_card_init(u32 addr, unsigned gpio);
-- 
cgit v1.2.3


From 63b68901dfd590cc13d4fe5c08dec2ca75b3c4aa Mon Sep 17 00:00:00 2001
From: Roger Quadros
Date: Fri, 14 Dec 2012 09:09:11 -0800
Subject: mfd: omap-usb-host: get rid of cpu_is_omap..() macros

Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.

The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/usb-host.c         | 4 ++++
 drivers/mfd/omap-usb-host.c            | 3 +--
 include/linux/platform_data/usb-omap.h | 3 +++
 3 files changed, 8 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c
index d1dbe125b34f..2e44e8a22884 100644
--- a/arch/arm/mach-omap2/usb-host.c
+++ b/arch/arm/mach-omap2/usb-host.c
@@ -508,6 +508,10 @@ void __init usbhs_init(const struct usbhs_omap_board_data *pdata)
 	if (cpu_is_omap34xx()) {
 		setup_ehci_io_mux(pdata->port_mode);
 		setup_ohci_io_mux(pdata->port_mode);
+
+		if (omap_rev() <= OMAP3430_REV_ES2_1)
+			usbhs_data.single_ulpi_bypass = true;
+
 	} else if (cpu_is_omap44xx()) {
 		setup_4430ehci_io_mux(pdata->port_mode);
 		setup_4430ohci_io_mux(pdata->port_mode);
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 770a0d01e0b9..05164d7f054b 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -25,7 +25,6 @@
 #include <linux/dma-mapping.h>
 #include <linux/spinlock.h>
 #include <linux/gpio.h>
-#include <plat/cpu.h>
 #include <linux/platform_device.h>
 #include <linux/platform_data/usb-omap.h>
 #include <linux/pm_runtime.h>
@@ -384,7 +383,7 @@ static void omap_usbhs_init(struct device *dev)
 			reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
 
 		/* Bypass the TLL module for PHY mode operation */
-		if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
+		if (pdata->single_ulpi_bypass) {
 			dev_dbg(dev, "OMAP3 ES version <= ES2.1\n");
 			if (is_ehci_phy_mode(pdata->port_mode[0]) ||
 				is_ehci_phy_mode(pdata->port_mode[1]) ||
diff --git a/include/linux/platform_data/usb-omap.h b/include/linux/platform_data/usb-omap.h
index 8570bcfe6311..ef65b67c56c3 100644
--- a/include/linux/platform_data/usb-omap.h
+++ b/include/linux/platform_data/usb-omap.h
@@ -59,6 +59,9 @@ struct usbhs_omap_platform_data {
 
 	struct ehci_hcd_omap_platform_data	*ehci_data;
 	struct ohci_hcd_omap_platform_data	*ohci_data;
+
+	/* OMAP3 <= ES2.1 have a single ulpi bypass control bit */
+	unsigned				single_ulpi_bypass:1;
 };
 
 /*-------------------------------------------------------------------------*/
-- 
cgit v1.2.3


From d695c82f250237f5bb1dba85cfc292fdf2b661ed Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Fri, 14 Dec 2012 14:34:18 -0600
Subject: ARM: dts: OMAP2420: Correct H4 board memory size

The system memory node for the OMAP2420 H4 was incorrectly defined as
start address followed by end address, instead of start address and
size. No noticable side-effects were observed but fix this for
correctness.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/omap2420-h4.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/omap2420-h4.dts
index 77b84e17c477..9b0d07746cba 100644
--- a/arch/arm/boot/dts/omap2420-h4.dts
+++ b/arch/arm/boot/dts/omap2420-h4.dts
@@ -15,6 +15,6 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x80000000 0x84000000>; /* 64 MB */
+		reg = <0x80000000 0x4000000>; /* 64 MB */
 	};
 };
-- 
cgit v1.2.3


From 30a6998ef4474b18d81d8c459f2cbd9e49ff0736 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Fri, 14 Dec 2012 15:55:39 -0600
Subject: ARM: dts: Add build target for omap4-panda-a4

Commit 0d9250c (ARM: dts: omap4-panda: Add pinmux configuration for
HDMI) added a new device-tree source file for Rev A4 of the OMAP4430
Panda board but it did not add this version to the makefile. Hence,
add this file to the makefile.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/boot/dts/Makefile | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 2af359cfe985..f8b4ff49b237 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -105,6 +105,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-evm.dtb \
 	omap3-tobi.dtb \
 	omap4-panda.dtb \
+	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \
 	omap4-var-som.dtb \
 	omap4-sdp.dtb \
-- 
cgit v1.2.3


From d9ba573718666df2e7e30d671f81bba39d07f91c Mon Sep 17 00:00:00 2001
From: Tony Lindgren
Date: Fri, 14 Dec 2012 09:09:11 -0800
Subject: ARM: OMAP: Move plat/omap-serial.h to
 include/linux/platform_data/serial-omap.h

We need to move this file to allow ARM multiplatform configurations
to build for omap2+. This can now be done as this file now only
contains platform_data.

cc: Russell King <linux@arm.linux.org.uk>
cc: Alan Cox <alan@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Govindraj.R <govindraj.raja@ti.com>
cc: Kevin Hilman <khilman@ti.com>
cc: linux-serial@vger.kernel.org
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/serial.c                  |  3 +-
 arch/arm/plat-omap/include/plat/omap-serial.h | 51 ---------------------------
 drivers/tty/serial/omap-serial.c              |  3 +-
 include/linux/platform_data/serial-omap.h     | 51 +++++++++++++++++++++++++++
 4 files changed, 53 insertions(+), 55 deletions(-)
 delete mode 100644 arch/arm/plat-omap/include/plat/omap-serial.h
 create mode 100644 include/linux/platform_data/serial-omap.h

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 93d102535c85..04fdbc4c499b 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -27,8 +27,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/console.h>
 #include <linux/omap-dma.h>
-
-#include <plat/omap-serial.h>
+#include <linux/platform_data/serial-omap.h>
 
 #include "common.h"
 #include "omap_hwmod.h"
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
deleted file mode 100644
index ff9b0aab5281..000000000000
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * Driver for OMAP-UART controller.
- * Based on drivers/serial/8250.c
- *
- * Copyright (C) 2010 Texas Instruments.
- *
- * Authors:
- *	Govindraj R	<govindraj.raja@ti.com>
- *	Thara Gopinath	<thara@ti.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef __OMAP_SERIAL_H__
-#define __OMAP_SERIAL_H__
-
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/pm_qos.h>
-
-#define DRIVER_NAME	"omap_uart"
-
-/*
- * Use tty device name as ttyO, [O -> OMAP]
- * in bootargs we specify as console=ttyO0 if uart1
- * is used as console uart.
- */
-#define OMAP_SERIAL_NAME	"ttyO"
-
-struct omap_uart_port_info {
-	bool			dma_enabled;	/* To specify DMA Mode */
-	unsigned int		uartclk;	/* UART clock rate */
-	upf_t			flags;		/* UPF_* flags */
-	unsigned int		dma_rx_buf_size;
-	unsigned int		dma_rx_timeout;
-	unsigned int		autosuspend_timeout;
-	unsigned int		dma_rx_poll_rate;
-	int			DTR_gpio;
-	int			DTR_inverted;
-	int			DTR_present;
-
-	int (*get_context_loss_count)(struct device *);
-	void (*set_forceidle)(struct device *);
-	void (*set_noidle)(struct device *);
-	void (*enable_wakeup)(struct device *, bool);
-};
-
-#endif /* __OMAP_SERIAL_H__ */
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 23f797eb7a28..57d6b29c039c 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -41,8 +41,7 @@
 #include <linux/of.h>
 #include <linux/gpio.h>
 #include <linux/pinctrl/consumer.h>
-
-#include <plat/omap-serial.h>
+#include <linux/platform_data/serial-omap.h>
 
 #define OMAP_MAX_HSUART_PORTS	6
 
diff --git a/include/linux/platform_data/serial-omap.h b/include/linux/platform_data/serial-omap.h
new file mode 100644
index 000000000000..ff9b0aab5281
--- /dev/null
+++ b/include/linux/platform_data/serial-omap.h
@@ -0,0 +1,51 @@
+/*
+ * Driver for OMAP-UART controller.
+ * Based on drivers/serial/8250.c
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * Authors:
+ *	Govindraj R	<govindraj.raja@ti.com>
+ *	Thara Gopinath	<thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __OMAP_SERIAL_H__
+#define __OMAP_SERIAL_H__
+
+#include <linux/serial_core.h>
+#include <linux/device.h>
+#include <linux/pm_qos.h>
+
+#define DRIVER_NAME	"omap_uart"
+
+/*
+ * Use tty device name as ttyO, [O -> OMAP]
+ * in bootargs we specify as console=ttyO0 if uart1
+ * is used as console uart.
+ */
+#define OMAP_SERIAL_NAME	"ttyO"
+
+struct omap_uart_port_info {
+	bool			dma_enabled;	/* To specify DMA Mode */
+	unsigned int		uartclk;	/* UART clock rate */
+	upf_t			flags;		/* UPF_* flags */
+	unsigned int		dma_rx_buf_size;
+	unsigned int		dma_rx_timeout;
+	unsigned int		autosuspend_timeout;
+	unsigned int		dma_rx_poll_rate;
+	int			DTR_gpio;
+	int			DTR_inverted;
+	int			DTR_present;
+
+	int (*get_context_loss_count)(struct device *);
+	void (*set_forceidle)(struct device *);
+	void (*set_noidle)(struct device *);
+	void (*enable_wakeup)(struct device *, bool);
+};
+
+#endif /* __OMAP_SERIAL_H__ */
-- 
cgit v1.2.3


From ba68c7eff599705b5fe3b42895dd7d2757cb368a Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Sat, 15 Dec 2012 01:35:39 -0700
Subject: ARM: OMAP4: Update timer clock aliases

Commit "ARM: dts: OMAP4: Update timer addresses" updated the device-tree
names of the OMAP4 timers 5-7 because the default address for the timers
was changed from the L3 address to the MPU private address. When booting
with device-tree, this introduces a regression when attempting to set
the parent clock of timers 5-7 to the sys_clk_div_ck. Therefore, update
the clock aliases for timer 5-7 to reflect the updated device-tree name
for the timers.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply after the CCF conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/cclock44xx_data.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index aa56c3e5bb34..a1f0b55b78e3 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -1935,10 +1935,10 @@ static struct omap_clk omap44xx_clks[] = {
 	CLK("4803e000.timer",	"timer_sys_ck",	&sys_clkin_ck,	CK_443X),
 	CLK("48086000.timer",	"timer_sys_ck",	&sys_clkin_ck,	CK_443X),
 	CLK("48088000.timer",	"timer_sys_ck",	&sys_clkin_ck,	CK_443X),
-	CLK("49038000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
-	CLK("4903a000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
-	CLK("4903c000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
-	CLK("4903e000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
+	CLK("40138000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
+	CLK("4013a000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
+	CLK("4013c000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
+	CLK("4013e000.timer",	"timer_sys_ck",	&syc_clk_div_ck,	CK_443X),
 	CLK(NULL,	"cpufreq_ck",	&dpll_mpu_ck,	CK_443X),
 };
 
-- 
cgit v1.2.3


From 9b4fcc86941ec0c12b27fefa39dc85e32244dc64 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Sat, 15 Dec 2012 01:35:43 -0700
Subject: ARM: OMAP4: Add function table for non-M4X dplls

Currently all OMAP4 non-core DPLLs use the same function table for
configuring DPLLs. For these DPLLs, the function
omap4_dpll_regm4xen_recalc() is used to recalculate the DPLL rate and
the function omap4_dpll_regm4xen_round_rate() is used to calculate the
closest rate to that requested. However, these omap4_dpll_regm4xen_xxx()
functions are only applicable to the ABE DPLL and not the other non-core
DPLLs. Therefore, add a new function table for non-core DPLLs that do
not include the 4X-multiplier (M4X).

Please note that using these omap4_dpll_regm4x_xxx() function works for
the non-M4X DPLLs today because we only check to see if the 4X
multiplier is enabled when calculating the rate. However, it is planned
that the dpll functions will be enhanced to enable the 4X multiplier as
necessary (in order to achieve the requested rate) and so calling these
functions for non-M4X dplls will no longer work.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/cclock44xx_data.c | 17 +++++++++++++----
 1 file changed, 13 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index a1f0b55b78e3..7c1ffe61ec1b 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -365,6 +365,15 @@ static struct dpll_data dpll_iva_dd = {
 
 static struct clk dpll_iva_ck;
 
+static const struct clk_ops dpll_ck_ops = {
+	.enable		= &omap3_noncore_dpll_enable,
+	.disable	= &omap3_noncore_dpll_disable,
+	.recalc_rate	= &omap3_dpll_recalc,
+	.round_rate	= &omap2_dpll_round_rate,
+	.set_rate	= &omap3_noncore_dpll_set_rate,
+	.get_parent	= &omap2_init_dpll_parent,
+};
+
 static struct clk_hw_omap dpll_iva_ck_hw = {
 	.hw = {
 		.clk = &dpll_iva_ck,
@@ -373,7 +382,7 @@ static struct clk_hw_omap dpll_iva_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_iva_ck, dpll_core_ck_parents, dpll_abe_ck_ops);
+DEFINE_STRUCT_CLK(dpll_iva_ck, dpll_core_ck_parents, dpll_ck_ops);
 
 static const char *dpll_iva_x2_ck_parents[] = {
 	"dpll_iva_ck",
@@ -426,7 +435,7 @@ static struct clk_hw_omap dpll_mpu_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_mpu_ck, dpll_core_ck_parents, dpll_abe_ck_ops);
+DEFINE_STRUCT_CLK(dpll_mpu_ck, dpll_core_ck_parents, dpll_ck_ops);
 
 DEFINE_CLK_FIXED_FACTOR(mpu_periphclk, "dpll_mpu_ck", &dpll_mpu_ck, 0x0, 1, 2);
 
@@ -475,7 +484,7 @@ static struct clk_hw_omap dpll_per_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_per_ck, dpll_core_ck_parents, dpll_abe_ck_ops);
+DEFINE_STRUCT_CLK(dpll_per_ck, dpll_core_ck_parents, dpll_ck_ops);
 
 DEFINE_CLK_DIVIDER(dpll_per_m2_ck, "dpll_per_ck", &dpll_per_ck, 0x0,
 		   OMAP4430_CM_DIV_M2_DPLL_PER, OMAP4430_DPLL_CLKOUT_DIV_SHIFT,
@@ -569,7 +578,7 @@ static struct clk_hw_omap dpll_usb_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_usb_ck, dpll_core_ck_parents, dpll_abe_ck_ops);
+DEFINE_STRUCT_CLK(dpll_usb_ck, dpll_core_ck_parents, dpll_ck_ops);
 
 static const char *dpll_usb_clkdcoldo_ck_parents[] = {
 	"dpll_usb_ck",
-- 
cgit v1.2.3


From 3ff51ed8287d3d2c7899f18f0487348e3448afb5 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Sat, 15 Dec 2012 01:35:46 -0700
Subject: ARM: OMAP4: Enhance support for DPLLs with 4X multiplier

On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can
be enabled or disabled in addition to the standard configurable
multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X
multiplier is accounted for by checking to see whether it is enabled or
not. However, when calculating a new rate we only check to see if the
rate can be achieved with the current setting for the 4X multiplier.
Enhance the round_rate() function for such DPLLs to see if the rate
can be achieved with the 4X multiplier if it cannot be achieved without
the 4X multiplier.

This change is necessary, because when using the 32kHz clock as the
source clock for the ABE DPLL, the default DPLL frequency for the ABE
DPLL cannot be achieved without enabling the 4X multiplier.

When using the 32kHz clock as the source clock for the ABE DPLL and
attempting to lock the DPLL to 98.304MHz (default frequency), it was
found that the DPLL would fail to lock if the low-power mode for the DPLL
was not enabled. From reviewing boot-loader settings that configure the
ABE DPLL it was found that the low-power mode is enabled when using the
32kHz clock source, however, the documentation for OMAP does not state
that this is a requirement. Therefore, introduce a new function for
OMAP4 devices to see if low-power mode can be enabled when calculating a
new rate to ensure the DPLL will lock.

New variables for the last calculated 4X multiplier and low-power
setting have been added to the dpll data structure as well as variables
defining the bit mask for enabling these features via the DPLL's
control_reg. It is possible that we could eliminate these bit masks from
the dpll data structure as these bit masks are not unique to OMAP4, if
it is preferred.

The function omap3_noncore_program_dpll() has been updated to avoid
passing the calculated values for the multiplier (M) and divider (N) as
these are stored in the clk structure.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/cclock44xx_data.c |  2 ++
 arch/arm/mach-omap2/clock.h           | 10 ++++++
 arch/arm/mach-omap2/dpll3xxx.c        | 46 +++++++++++++++++--------
 arch/arm/mach-omap2/dpll44xx.c        | 64 ++++++++++++++++++++++++++++++-----
 4 files changed, 99 insertions(+), 23 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index 7c1ffe61ec1b..44ef54fa118b 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -124,6 +124,8 @@ static struct dpll_data dpll_abe_dd = {
 	.enable_mask	= OMAP4430_DPLL_EN_MASK,
 	.autoidle_mask	= OMAP4430_AUTO_DPLL_MODE_MASK,
 	.idlest_mask	= OMAP4430_ST_DPLL_CLK_MASK,
+	.m4xen_mask	= OMAP4430_DPLL_REGM4XEN_MASK,
+	.lpmode_mask	= OMAP4430_DPLL_LPMODE_EN_MASK,
 	.max_multiplier	= 2047,
 	.max_divider	= 128,
 	.min_divider	= 1,
diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
index 9917f793c3b6..b40204837bd7 100644
--- a/arch/arm/mach-omap2/clock.h
+++ b/arch/arm/mach-omap2/clock.h
@@ -195,6 +195,10 @@ struct clksel {
  * @enable_mask: mask of the DPLL mode bitfield in @control_reg
  * @last_rounded_rate: cache of the last rate result of omap2_dpll_round_rate()
  * @last_rounded_m: cache of the last M result of omap2_dpll_round_rate()
+ * @last_rounded_m4xen: cache of the last M4X result of
+ *			omap4_dpll_regm4xen_round_rate()
+ * @last_rounded_lpmode: cache of the last lpmode result of
+ *			 omap4_dpll_lpmode_recalc()
  * @max_multiplier: maximum valid non-bypass multiplier value (actual)
  * @last_rounded_n: cache of the last N result of omap2_dpll_round_rate()
  * @min_divider: minimum valid non-bypass divider value (actual)
@@ -205,6 +209,8 @@ struct clksel {
  * @autoidle_mask: mask of the DPLL autoidle mode bitfield in @autoidle_reg
  * @freqsel_mask: mask of the DPLL jitter correction bitfield in @control_reg
  * @idlest_mask: mask of the DPLL idle status bitfield in @idlest_reg
+ * @lpmode_mask: mask of the DPLL low-power mode bitfield in @control_reg
+ * @m4xen_mask: mask of the DPLL M4X multiplier bitfield in @control_reg
  * @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg
  * @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs
  * @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs
@@ -233,6 +239,8 @@ struct dpll_data {
 	u32			enable_mask;
 	unsigned long		last_rounded_rate;
 	u16			last_rounded_m;
+	u8			last_rounded_m4xen;
+	u8			last_rounded_lpmode;
 	u16			max_multiplier;
 	u8			last_rounded_n;
 	u8			min_divider;
@@ -245,6 +253,8 @@ struct dpll_data {
 	u32			idlest_mask;
 	u32			dco_mask;
 	u32			sddiv_mask;
+	u32			lpmode_mask;
+	u32			m4xen_mask;
 	u8			auto_recal_bit;
 	u8			recal_en_bit;
 	u8			recal_st_bit;
diff --git a/arch/arm/mach-omap2/dpll3xxx.c b/arch/arm/mach-omap2/dpll3xxx.c
index fafb28c0dcbc..2bb18838cba9 100644
--- a/arch/arm/mach-omap2/dpll3xxx.c
+++ b/arch/arm/mach-omap2/dpll3xxx.c
@@ -291,16 +291,13 @@ static void _lookup_sddiv(struct clk_hw_omap *clk, u8 *sd_div, u16 m, u8 n)
 
 /*
  * _omap3_noncore_dpll_program - set non-core DPLL M,N values directly
- * @clk: struct clk * of DPLL to set
- * @m: DPLL multiplier to set
- * @n: DPLL divider to set
- * @freqsel: FREQSEL value to set
+ * @clk:	struct clk * of DPLL to set
+ * @freqsel:	FREQSEL value to set
  *
- * Program the DPLL with the supplied M, N values, and wait for the DPLL to
- * lock..  Returns -EINVAL upon error, or 0 upon success.
+ * Program the DPLL with the last M, N values calculated, and wait for
+ * the DPLL to lock. Returns -EINVAL upon error, or 0 upon success.
  */
-static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 m, u8 n,
-				      u16 freqsel)
+static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel)
 {
 	struct dpll_data *dd = clk->dpll_data;
 	u8 dco, sd_div;
@@ -323,23 +320,45 @@ static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 m, u8 n,
 	/* Set DPLL multiplier, divider */
 	v = __raw_readl(dd->mult_div1_reg);
 	v &= ~(dd->mult_mask | dd->div1_mask);
-	v |= m << __ffs(dd->mult_mask);
-	v |= (n - 1) << __ffs(dd->div1_mask);
+	v |= dd->last_rounded_m << __ffs(dd->mult_mask);
+	v |= (dd->last_rounded_n - 1) << __ffs(dd->div1_mask);
 
 	/* Configure dco and sd_div for dplls that have these fields */
 	if (dd->dco_mask) {
-		_lookup_dco(clk, &dco, m, n);
+		_lookup_dco(clk, &dco, dd->last_rounded_m, dd->last_rounded_n);
 		v &= ~(dd->dco_mask);
 		v |= dco << __ffs(dd->dco_mask);
 	}
 	if (dd->sddiv_mask) {
-		_lookup_sddiv(clk, &sd_div, m, n);
+		_lookup_sddiv(clk, &sd_div, dd->last_rounded_m,
+			      dd->last_rounded_n);
 		v &= ~(dd->sddiv_mask);
 		v |= sd_div << __ffs(dd->sddiv_mask);
 	}
 
 	__raw_writel(v, dd->mult_div1_reg);
 
+	/* Set 4X multiplier and low-power mode */
+	if (dd->m4xen_mask || dd->lpmode_mask) {
+		v = __raw_readl(dd->control_reg);
+
+		if (dd->m4xen_mask) {
+			if (dd->last_rounded_m4xen)
+				v |= dd->m4xen_mask;
+			else
+				v &= ~dd->m4xen_mask;
+		}
+
+		if (dd->lpmode_mask) {
+			if (dd->last_rounded_lpmode)
+				v |= dd->lpmode_mask;
+			else
+				v &= ~dd->lpmode_mask;
+		}
+
+		__raw_writel(v, dd->control_reg);
+	}
+
 	/* We let the clock framework set the other output dividers later */
 
 	/* REVISIT: Set ramp-up delay? */
@@ -492,8 +511,7 @@ int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate,
 		pr_debug("%s: %s: set rate: locking rate to %lu.\n",
 			 __func__, __clk_get_name(hw->clk), rate);
 
-		ret = omap3_noncore_dpll_program(clk, dd->last_rounded_m,
-						dd->last_rounded_n, freqsel);
+		ret = omap3_noncore_dpll_program(clk, freqsel);
 		if (!ret)
 			new_parent = dd->clk_ref;
 	}
diff --git a/arch/arm/mach-omap2/dpll44xx.c b/arch/arm/mach-omap2/dpll44xx.c
index d3326c474fdc..d28b0f726715 100644
--- a/arch/arm/mach-omap2/dpll44xx.c
+++ b/arch/arm/mach-omap2/dpll44xx.c
@@ -20,6 +20,15 @@
 #include "clock44xx.h"
 #include "cm-regbits-44xx.h"
 
+/*
+ * Maximum DPLL input frequency (FINT) and output frequency (FOUT) that
+ * can supported when using the DPLL low-power mode. Frequencies are
+ * defined in OMAP4430/60 Public TRM section 3.6.3.3.2 "Enable Control,
+ * Status, and Low-Power Operation Mode".
+ */
+#define OMAP4_DPLL_LP_FINT_MAX	1000000
+#define OMAP4_DPLL_LP_FOUT_MAX	100000000
+
 /* Supported only on OMAP4 */
 int omap4_dpllmx_gatectrl_read(struct clk_hw_omap *clk)
 {
@@ -81,6 +90,31 @@ const struct clk_hw_omap_ops clkhwops_omap4_dpllmx = {
 	.deny_idle      = omap4_dpllmx_deny_gatectrl,
 };
 
+/**
+ * omap4_dpll_lpmode_recalc - compute DPLL low-power setting
+ * @dd: pointer to the dpll data structure
+ *
+ * Calculates if low-power mode can be enabled based upon the last
+ * multiplier and divider values calculated. If low-power mode can be
+ * enabled, then the bit to enable low-power mode is stored in the
+ * last_rounded_lpmode variable. This implementation is based upon the
+ * criteria for enabling low-power mode as described in the OMAP4430/60
+ * Public TRM section 3.6.3.3.2 "Enable Control, Status, and Low-Power
+ * Operation Mode".
+ */
+static void omap4_dpll_lpmode_recalc(struct dpll_data *dd)
+{
+	long fint, fout;
+
+	fint = __clk_get_rate(dd->clk_ref) / (dd->last_rounded_n + 1);
+	fout = fint * dd->last_rounded_m;
+
+	if ((fint < OMAP4_DPLL_LP_FINT_MAX) && (fout < OMAP4_DPLL_LP_FOUT_MAX))
+		dd->last_rounded_lpmode = 1;
+	else
+		dd->last_rounded_lpmode = 0;
+}
+
 /**
  * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit
  * @clk: struct clk * of the DPLL to compute the rate for
@@ -130,7 +164,6 @@ long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw,
 				    unsigned long *parent_rate)
 {
 	struct clk_hw_omap *clk = to_clk_hw_omap(hw);
-	u32 v;
 	struct dpll_data *dd;
 	long r;
 
@@ -139,18 +172,31 @@ long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw,
 
 	dd = clk->dpll_data;
 
-	/* regm4xen adds a multiplier of 4 to DPLL calculations */
-	v = __raw_readl(dd->control_reg) & OMAP4430_DPLL_REGM4XEN_MASK;
-
-	if (v)
-		target_rate = target_rate / OMAP4430_REGM4XEN_MULT;
+	dd->last_rounded_m4xen = 0;
 
+	/*
+	 * First try to compute the DPLL configuration for
+	 * target rate without using the 4X multiplier.
+	 */
 	r = omap2_dpll_round_rate(hw, target_rate, NULL);
+	if (r != ~0)
+		goto out;
+
+	/*
+	 * If we did not find a valid DPLL configuration, try again, but
+	 * this time see if using the 4X multiplier can help. Enabling the
+	 * 4X multiplier is equivalent to dividing the target rate by 4.
+	 */
+	r = omap2_dpll_round_rate(hw, target_rate / OMAP4430_REGM4XEN_MULT,
+				  NULL);
 	if (r == ~0)
 		return r;
 
-	if (v)
-		clk->dpll_data->last_rounded_rate *= OMAP4430_REGM4XEN_MULT;
+	dd->last_rounded_rate *= OMAP4430_REGM4XEN_MULT;
+	dd->last_rounded_m4xen = 1;
+
+out:
+	omap4_dpll_lpmode_recalc(dd);
 
-	return clk->dpll_data->last_rounded_rate;
+	return dd->last_rounded_rate;
 }
-- 
cgit v1.2.3


From 8c197ccfb60032859a32381b2e4bd4d2b8fdd338 Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Sat, 15 Dec 2012 01:35:50 -0700
Subject: ARM: OMAP4460: Workaround ABE DPLL failing to turn-on

With the latest mainline u-boot bootloader (v2012.10), timers (5-8) in
the ABE power domain are failing to turn-on. The timers never come out
of the disabled state when setting the module-mode field to enable.

The problem was exposed when u-boot was updated to NOT configure and
lock the ABE DPLL on start-up. If the ABE DPLL is configured and locked
by u-boot the problem does not occur. However, if the ABE DPLL is in the
idle low-power bypass state and we attempt to enable a timer in the ABE
power domain, it remains stuck in the disabled state. It appears to be a
problem the timer interface clock as this comes from the ABE DPLL.

If we place the ABE DPLL in the MN-bypass state and not the idle
low-power state, then this problem is not seen.

This problem only appears to occur on OMAP4460 and not OMAP4430.

Workaround this problem by locking the ABE DPLL for OMAP4460 in the
kernel on boot. By locking the ABE DPLL, when clocks from the ABE DPLL
are not being requested the DPLL will transition into a low-power stop
mode.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/cclock44xx_data.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index 44ef54fa118b..30da1ad7ec8d 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -40,6 +40,14 @@
 #define OMAP4430_MODULEMODE_HWCTRL_SHIFT		0
 #define OMAP4430_MODULEMODE_SWCTRL_SHIFT		1
 
+/*
+ * OMAP4 ABE DPLL default frequency. In OMAP4460 TRM version V, section
+ * "3.6.3.2.3 CM1_ABE Clock Generator" states that the "DPLL_ABE_X2_CLK
+ * must be set to 196.608 MHz" and hence, the DPLL locked frequency is
+ * half of this value.
+ */
+#define OMAP4_DPLL_ABE_DEFFREQ				98304000
+
 /* Root clocks */
 
 DEFINE_CLK_FIXED_RATE(extalt_clkin_ck, CLK_IS_ROOT, 59000000, 0x0);
@@ -1966,6 +1974,7 @@ int __init omap4xxx_clk_init(void)
 {
 	u32 cpu_clkflg;
 	struct omap_clk *c;
+	int rc;
 
 	if (cpu_is_omap443x()) {
 		cpu_mask = RATE_IN_4430;
@@ -1994,5 +2003,18 @@ int __init omap4xxx_clk_init(void)
 	omap2_clk_enable_init_clocks(enable_init_clks,
 				     ARRAY_SIZE(enable_init_clks));
 
+	/*
+	 * On OMAP4460 the ABE DPLL fails to turn on if in idle low-power
+	 * state when turning the ABE clock domain. Workaround this by
+	 * locking the ABE DPLL on boot.
+	 */
+	if (cpu_is_omap446x()) {
+		rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
+		if (!rc)
+			rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
+		if (rc)
+			pr_err("%s: failed to configure ABE DPLL!\n", __func__);
+	}
+
 	return 0;
 }
-- 
cgit v1.2.3


From 29f0667f9239c2af48ef51c50b12c0250c65bb2a Mon Sep 17 00:00:00 2001
From: Jon Hunter
Date: Sat, 15 Dec 2012 01:35:54 -0700
Subject: ARM: OMAP4: Fix EMU clock domain always on

Commit d043d87 (ARM: OMAP2+: clockdomain: bypass clockdomain handling
when disabling unused clks) skips the decrementing of a clock-domains
use count if the clocks use count is zero. However, for OMAP4 devices
this is causing the EMU clock-domain to be stuck ON as the use count is
not getting decremented correctly.

The scenario that leads to this problem is described below ...

omap_hwmod_setup_all
--> _setup
    --> clkdm_hwmod_enable
    	--> EMU clock domain usecount = 1
    --> _enable_clocks
        --> clk_enable
	    --> trace_clk_div_div usecount = 1
            --> clkdm_hwmod_enable
    	        --> EMU clock domain usecount = 2
--> _idle
    --> _disable_clocks
	--> clk_disable
            --> trace_clk_div_div usecount = 0
            --> clkdm_hwmod_disable
                --> skips decrement of EMU clock domain usecount
		    because trace_clk_div_div is 0!
    	        --> EMU clock domain usecount = 2
    --> clkdm_hwmod_disable
    	--> EMU clock domain usecount = 1

Hence, due to the order that a clocks use count is decremented and the
clock domain is disabled, it is possible that the clock domain can have
a non-zero use count when the actual clock has a use count of 0.
Therefore, we should only bypass the clock-domain handling when both the
clock-domain and clock in the clock-domain have a use count of 0 and
warn when the clock-domain has a zero use count and the clock has a
non-zero use count.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/clockdomain.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/clockdomain.c b/arch/arm/mach-omap2/clockdomain.c
index 384873580b23..7faf82d4e85c 100644
--- a/arch/arm/mach-omap2/clockdomain.c
+++ b/arch/arm/mach-omap2/clockdomain.c
@@ -998,7 +998,8 @@ int clkdm_clk_disable(struct clockdomain *clkdm, struct clk *clk)
 	spin_lock_irqsave(&clkdm->lock, flags);
 
 	/* corner case: disabling unused clocks */
-	if (__clk_get_enable_count(clk) == 0)
+	if ((__clk_get_enable_count(clk) == 0) &&
+	    (atomic_read(&clkdm->usecount) == 0))
 		goto ccd_exit;
 
 	if (atomic_read(&clkdm->usecount) == 0) {
-- 
cgit v1.2.3


From 628a37d40e27886f94946d91d71ac323b826809c Mon Sep 17 00:00:00 2001
From: Paul Walmsley
Date: Sat, 15 Dec 2012 01:35:58 -0700
Subject: ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider

The OMAP4 clock divider "div_iva_hs_clk" is listed in the clock data
as an OMAP HSDIVIDER, but it's actually a power-of-two divider.  This
causes a warning during boot on an OMAP4460 Pandaboard-ES with a
recent u-boot:

WARNING: at arch/arm/mach-omap2/clkt_clksel.c:143 omap2_clksel_recalc+0xf4/0x12c()
clock: div_iva_hs_clk: could not find fieldval 0 for parent dpll_core_m5x2_ck

Fix by converting the data for this clock to a power-of-two divider.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
---
 arch/arm/mach-omap2/cclock44xx_data.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index 30da1ad7ec8d..259280ad6059 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -296,9 +296,9 @@ DEFINE_CLK_DIVIDER(div_core_ck, "dpll_core_m5x2_ck", &dpll_core_m5x2_ck, 0x0,
 		   OMAP4430_CM_CLKSEL_CORE, OMAP4430_CLKSEL_CORE_SHIFT,
 		   OMAP4430_CLKSEL_CORE_WIDTH, 0x0, NULL);
 
-DEFINE_CLK_OMAP_HSDIVIDER(div_iva_hs_clk, "dpll_core_m5x2_ck",
-			  &dpll_core_m5x2_ck, 0x0, OMAP4430_CM_BYPCLK_DPLL_IVA,
-			  OMAP4430_CLKSEL_0_1_MASK);
+DEFINE_CLK_DIVIDER(div_iva_hs_clk, "dpll_core_m5x2_ck", &dpll_core_m5x2_ck,
+		   0x0, OMAP4430_CM_BYPCLK_DPLL_IVA, OMAP4430_CLKSEL_0_1_SHIFT,
+		   OMAP4430_CLKSEL_0_1_WIDTH, CLK_DIVIDER_POWER_OF_TWO, NULL);
 
 DEFINE_CLK_DIVIDER(div_mpu_hs_clk, "dpll_core_m5x2_ck", &dpll_core_m5x2_ck,
 		   0x0, OMAP4430_CM_BYPCLK_DPLL_MPU, OMAP4430_CLKSEL_0_1_SHIFT,
-- 
cgit v1.2.3


From b8675e2c04fd368f0a726b7e4583946f7b8e7125 Mon Sep 17 00:00:00 2001
From: Paul Walmsley
Date: Sat, 15 Dec 2012 01:36:04 -0700
Subject: ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their
 parent lists

Booting OMAP4460 Pandaboard ES with a recent u-boot results in this
warning:

WARNING: at arch/arm/mach-omap2/dpll3xxx.c:427 omap3_noncore_dpll_enable+0xf4/0x110()

The OMAP4 DPLL parent clock names only listed the reference clocks,
not the bypass clocks.  Fix by adding the bypass clocks to the DPLL
parent lists.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>---
 arch/arm/mach-omap2/cclock44xx_data.c | 31 +++++++++++++++++++++++++------
 1 file changed, 25 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index 259280ad6059..5789a5e25563 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -243,7 +243,7 @@ static struct dpll_data dpll_core_dd = {
 
 
 static const char *dpll_core_ck_parents[] = {
-	"sys_clkin_ck",
+	"sys_clkin_ck", "core_hsd_byp_clk_mux_ck"
 };
 
 static struct clk dpll_core_ck;
@@ -373,6 +373,10 @@ static struct dpll_data dpll_iva_dd = {
 	.min_divider	= 1,
 };
 
+static const char *dpll_iva_ck_parents[] = {
+	"sys_clkin_ck", "iva_hsd_byp_clk_mux_ck"
+};
+
 static struct clk dpll_iva_ck;
 
 static const struct clk_ops dpll_ck_ops = {
@@ -392,7 +396,7 @@ static struct clk_hw_omap dpll_iva_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_iva_ck, dpll_core_ck_parents, dpll_ck_ops);
+DEFINE_STRUCT_CLK(dpll_iva_ck, dpll_iva_ck_parents, dpll_ck_ops);
 
 static const char *dpll_iva_x2_ck_parents[] = {
 	"dpll_iva_ck",
@@ -435,6 +439,10 @@ static struct dpll_data dpll_mpu_dd = {
 	.min_divider	= 1,
 };
 
+static const char *dpll_mpu_ck_parents[] = {
+	"sys_clkin_ck", "div_mpu_hs_clk"
+};
+
 static struct clk dpll_mpu_ck;
 
 static struct clk_hw_omap dpll_mpu_ck_hw = {
@@ -445,7 +453,7 @@ static struct clk_hw_omap dpll_mpu_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_mpu_ck, dpll_core_ck_parents, dpll_ck_ops);
+DEFINE_STRUCT_CLK(dpll_mpu_ck, dpll_mpu_ck_parents, dpll_ck_ops);
 
 DEFINE_CLK_FIXED_FACTOR(mpu_periphclk, "dpll_mpu_ck", &dpll_mpu_ck, 0x0, 1, 2);
 
@@ -483,6 +491,9 @@ static struct dpll_data dpll_per_dd = {
 	.min_divider	= 1,
 };
 
+static const char *dpll_per_ck_parents[] = {
+	"sys_clkin_ck", "per_hsd_byp_clk_mux_ck"
+};
 
 static struct clk dpll_per_ck;
 
@@ -494,7 +505,7 @@ static struct clk_hw_omap dpll_per_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_per_ck, dpll_core_ck_parents, dpll_ck_ops);
+DEFINE_STRUCT_CLK(dpll_per_ck, dpll_per_ck_parents, dpll_ck_ops);
 
 DEFINE_CLK_DIVIDER(dpll_per_m2_ck, "dpll_per_ck", &dpll_per_ck, 0x0,
 		   OMAP4430_CM_DIV_M2_DPLL_PER, OMAP4430_DPLL_CLKOUT_DIV_SHIFT,
@@ -578,6 +589,10 @@ static struct dpll_data dpll_usb_dd = {
 	.min_divider	= 1,
 };
 
+static const char *dpll_usb_ck_parents[] = {
+	"sys_clkin_ck", "usb_hs_clk_div_ck"
+};
+
 static struct clk dpll_usb_ck;
 
 static struct clk_hw_omap dpll_usb_ck_hw = {
@@ -588,7 +603,7 @@ static struct clk_hw_omap dpll_usb_ck_hw = {
 	.ops		= &clkhwops_omap3_dpll,
 };
 
-DEFINE_STRUCT_CLK(dpll_usb_ck, dpll_core_ck_parents, dpll_ck_ops);
+DEFINE_STRUCT_CLK(dpll_usb_ck, dpll_usb_ck_parents, dpll_ck_ops);
 
 static const char *dpll_usb_clkdcoldo_ck_parents[] = {
 	"dpll_usb_ck",
@@ -715,9 +730,13 @@ DEFINE_CLK_DIVIDER(syc_clk_div_ck, "sys_clkin_ck", &sys_clkin_ck, 0x0,
 		   OMAP4430_CM_ABE_DSS_SYS_CLKSEL, OMAP4430_CLKSEL_0_0_SHIFT,
 		   OMAP4430_CLKSEL_0_0_WIDTH, 0x0, NULL);
 
+static const char *dbgclk_mux_ck_parents[] = {
+	"sys_clkin_ck"
+};
+
 static struct clk dbgclk_mux_ck;
 DEFINE_STRUCT_CLK_HW_OMAP(dbgclk_mux_ck, NULL);
-DEFINE_STRUCT_CLK(dbgclk_mux_ck, dpll_core_ck_parents,
+DEFINE_STRUCT_CLK(dbgclk_mux_ck, dbgclk_mux_ck_parents,
 		  dpll_usb_clkdcoldo_ck_ops);
 
 /* Leaf clocks controlled by modules */
-- 
cgit v1.2.3


From 9db316b6bf0234d9391f87dd0d28b23f5a44facb Mon Sep 17 00:00:00 2001
From: Paul Walmsley
Date: Sat, 15 Dec 2012 01:39:19 -0700
Subject: ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings

Fix the following sparse warnings in the OMAP3/4 CPUIdle code:

arch/arm/mach-omap2/cpuidle34xx.c:272:1: warning: symbol 'omap3_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle34xx.c:274:23: warning: symbol 'omap3_idle_driver' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:164:1: warning: symbol 'omap4_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:166:23: warning: symbol 'omap4_idle_driver' was not declared. Should it be static?

Also fix the following checkpatch warnings:

WARNING: please, no space before tabs
#44: FILE: arch/arm/mach-omap2/cpuidle34xx.c:105:
+^I.name = ^I"omap3_idle",$

WARNING: please, no space before tabs
#45: FILE: arch/arm/mach-omap2/cpuidle34xx.c:106:
+^I.owner = ^ITHIS_MODULE,$

ERROR: code indent should use tabs where possible
#211: FILE: arch/arm/mach-omap2/cpuidle44xx.c:74:
+                        /* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */$


Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>---
 arch/arm/mach-omap2/cpuidle34xx.c | 14 +++++++++-----
 arch/arm/mach-omap2/cpuidle44xx.c | 28 ++++++++++++++++------------
 2 files changed, 25 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c
index bca7a8885703..22590dbe8f14 100644
--- a/arch/arm/mach-omap2/cpuidle34xx.c
+++ b/arch/arm/mach-omap2/cpuidle34xx.c
@@ -40,6 +40,8 @@ struct omap3_idle_statedata {
 	u32 core_state;
 };
 
+static struct powerdomain *mpu_pd, *core_pd, *per_pd, *cam_pd;
+
 static struct omap3_idle_statedata omap3_idle_data[] = {
 	{
 		.mpu_state = PWRDM_POWER_ON,
@@ -71,7 +73,7 @@ static struct omap3_idle_statedata omap3_idle_data[] = {
 	},
 };
 
-static struct powerdomain *mpu_pd, *core_pd, *per_pd, *cam_pd;
+/* Private functions */
 
 static int __omap3_enter_idle(struct cpuidle_device *dev,
 				struct cpuidle_driver *drv,
@@ -260,11 +262,11 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev,
 	return ret;
 }
 
-DEFINE_PER_CPU(struct cpuidle_device, omap3_idle_dev);
+static DEFINE_PER_CPU(struct cpuidle_device, omap3_idle_dev);
 
-struct cpuidle_driver omap3_idle_driver = {
-	.name = 	"omap3_idle",
-	.owner = 	THIS_MODULE,
+static struct cpuidle_driver omap3_idle_driver = {
+	.name =		"omap3_idle",
+	.owner =	THIS_MODULE,
 	.states = {
 		{
 			.enter		  = omap3_enter_idle_bm,
@@ -327,6 +329,8 @@ struct cpuidle_driver omap3_idle_driver = {
 	.safe_state_index = 0,
 };
 
+/* Public functions */
+
 /**
  * omap3_idle_init - Init routine for OMAP3 idle
  *
diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c
index 288bee6cbb76..d639aef0deda 100644
--- a/arch/arm/mach-omap2/cpuidle44xx.c
+++ b/arch/arm/mach-omap2/cpuidle44xx.c
@@ -54,6 +54,8 @@ static struct clockdomain *cpu_clkdm[NR_CPUS];
 static atomic_t abort_barrier;
 static bool cpu_done[NR_CPUS];
 
+/* Private functions */
+
 /**
  * omap4_enter_idle_coupled_[simple/coupled] - OMAP4 cpuidle entry functions
  * @dev: cpuidle device
@@ -161,9 +163,19 @@ fail:
 	return index;
 }
 
-DEFINE_PER_CPU(struct cpuidle_device, omap4_idle_dev);
+/*
+ * For each cpu, setup the broadcast timer because local timers
+ * stops for the states above C1.
+ */
+static void omap_setup_broadcast_timer(void *arg)
+{
+	int cpu = smp_processor_id();
+	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &cpu);
+}
+
+static DEFINE_PER_CPU(struct cpuidle_device, omap4_idle_dev);
 
-struct cpuidle_driver omap4_idle_driver = {
+static struct cpuidle_driver omap4_idle_driver = {
 	.name				= "omap4_idle",
 	.owner				= THIS_MODULE,
 	.en_core_tk_irqen		= 1,
@@ -178,7 +190,7 @@ struct cpuidle_driver omap4_idle_driver = {
 			.desc = "MPUSS ON"
 		},
 		{
-                        /* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */
+			/* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */
 			.exit_latency = 328 + 440,
 			.target_residency = 960,
 			.flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_COUPLED,
@@ -200,15 +212,7 @@ struct cpuidle_driver omap4_idle_driver = {
 	.safe_state_index = 0,
 };
 
-/*
- * For each cpu, setup the broadcast timer because local timers
- * stops for the states above C1.
- */
-static void omap_setup_broadcast_timer(void *arg)
-{
-	int cpu = smp_processor_id();
-	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &cpu);
-}
+/* Public functions */
 
 /**
  * omap4_idle_init - Init routine for OMAP4 idle
-- 
cgit v1.2.3


From d7dde8c191d136415819e4456e21f2b0cc00c326 Mon Sep 17 00:00:00 2001
From: Javier Martinez Canillas
Date: Sun, 16 Dec 2012 03:48:52 +0100
Subject: ARM: OMAP2+: common: remove use of vram

commit 966458f OMAP: remove vram allocator

Removed the OMAP specific vram allocator but OMAP2 common was
still trying to use it and this lead to the following build error:

CC      arch/arm/mach-omap2/common.o
arch/arm/mach-omap2/common.c:19:23: fatal error: plat/vram.h: No such file or directory
compilation terminated.
make[1]: *** [arch/arm/mach-omap2/common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/common.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/arch/arm/mach-omap2/common.c b/arch/arm/mach-omap2/common.c
index 5c2fd4863b2b..2dabb9ecb986 100644
--- a/arch/arm/mach-omap2/common.c
+++ b/arch/arm/mach-omap2/common.c
@@ -16,8 +16,6 @@
 #include <linux/init.h>
 #include <linux/platform_data/dsp-omap.h>
 
-#include <plat/vram.h>
-
 #include "common.h"
 #include "omap-secure.h"
 
@@ -32,7 +30,6 @@ int __weak omap_secure_ram_reserve_memblock(void)
 
 void __init omap_reserve(void)
 {
-	omap_vram_reserve_sdram_memblock();
 	omap_dsp_reserve_sdram_memblock();
 	omap_secure_ram_reserve_memblock();
 	omap_barrier_reserve_memblock();
-- 
cgit v1.2.3


From 3e24b05ba3be5281c3fbf0b126953f5810f9d8ab Mon Sep 17 00:00:00 2001
From: Fabio Estevam
Date: Wed, 21 Nov 2012 17:19:38 -0200
Subject: ARM: dts: mx27: Fix the AIPI bus for FEC

FEC controller is connected to AIPI2 bus.

Also fix the AIPI1 address range.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/boot/dts/imx27-3ds.dts            |  8 ++++----
 arch/arm/boot/dts/imx27-phytec-phycore.dts | 13 +++++++------
 arch/arm/boot/dts/imx27.dtsi               | 11 ++++++++++-
 3 files changed, 21 insertions(+), 11 deletions(-)

diff --git a/arch/arm/boot/dts/imx27-3ds.dts b/arch/arm/boot/dts/imx27-3ds.dts
index b01c0d745fc5..fa04c7b18bcb 100644
--- a/arch/arm/boot/dts/imx27-3ds.dts
+++ b/arch/arm/boot/dts/imx27-3ds.dts
@@ -21,17 +21,17 @@
 	};
 
 	soc {
-		aipi@10000000 { /* aipi */
-
+		aipi@10000000 { /* aipi1 */
 			uart1: serial@1000a000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
+		};
 
-			fec@1002b000 {
+		aipi@10020000 { /* aipi2 */
+			ethernet@1002b000 {
 				status = "okay";
 			};
 		};
 	};
-
 };
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore.dts b/arch/arm/boot/dts/imx27-phytec-phycore.dts
index af50469e34b2..53b0ec0c228e 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore.dts
+++ b/arch/arm/boot/dts/imx27-phytec-phycore.dts
@@ -21,8 +21,7 @@
 	};
 
 	soc {
-		aipi@10000000 { /* aipi */
-
+		aipi@10000000 { /* aipi1 */
 			serial@1000a000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
@@ -38,10 +37,6 @@
 				status = "okay";
 			};
 
-			ethernet@1002b000 {
-				status = "okay";
-			};
-
 			i2c@1001d000 {
 				clock-frequency = <400000>;
 				status = "okay";
@@ -60,6 +55,12 @@
 				};
 			};
 		};
+
+		aipi@10020000 { /* aipi2 */
+			ethernet@1002b000 {
+				status = "okay";
+			};
+		};
 	};
 
 	nor_flash@c0000000 {
diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
index b8d3905915ac..5a82cb5707a8 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/imx27.dtsi
@@ -55,7 +55,7 @@
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			reg = <0x10000000 0x10000000>;
+			reg = <0x10000000 0x20000>;
 			ranges;
 
 			wdog: wdog@10002000 {
@@ -211,6 +211,15 @@
 				status = "disabled";
 			};
 
+		};
+
+		aipi@10020000 { /* AIPI2 */
+			compatible = "fsl,aipi-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x10020000 0x20000>;
+			ranges;
+
 			fec: ethernet@1002b000 {
 				compatible = "fsl,imx27-fec";
 				reg = <0x1002b000 0x4000>;
-- 
cgit v1.2.3


From 69155fd66d340d47cf25eff0099b3e13548ed50c Mon Sep 17 00:00:00 2001
From: Sascha Hauer
Date: Tue, 11 Dec 2012 10:08:50 +0100
Subject: ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks

The MIPI/HSP clocks were recently turned on in the i.MX51 clock tree.
It turned out that the system does not work properly when the MIPI/HSP
clocks are enabled, but the IPU clock is disabled. This happens when
IPU support is disabled. In this case the IPU clock gets disabled when
the clock framework turns off unused clock in a late_initcall. This
is broken since:

| commit 9a2d4825a9368e018003a2732a61be063d178f67
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date:   Tue Jun 5 13:53:32 2012 +0200
|
|     ARM i.MX5: switch IPU clk support to devicetree bindings
|
|     The i.MX5 clk support has platform based clock bindings for the
|     IPU. IPU support is devicetree only, so move them over to devicetree
|     based bindings. Also, enable MIPI clocks which do not have a device
|     associated with, but still need to be enabled to do graphics on
|     i.MX51.

This patch fixes this by setting some reserved bits in the CCM as recommended
in the reference manual.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
---
 arch/arm/mach-imx/clk-imx51-imx53.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm/mach-imx/clk-imx51-imx53.c b/arch/arm/mach-imx/clk-imx51-imx53.c
index e8c0473c7568..579023f59dc1 100644
--- a/arch/arm/mach-imx/clk-imx51-imx53.c
+++ b/arch/arm/mach-imx/clk-imx51-imx53.c
@@ -319,6 +319,7 @@ int __init mx51_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 			unsigned long rate_ckih1, unsigned long rate_ckih2)
 {
 	int i;
+	u32 val;
 	struct device_node *np;
 
 	clk[pll1_sw] = imx_clk_pllv2("pll1_sw", "osc", MX51_DPLL1_BASE);
@@ -390,6 +391,21 @@ int __init mx51_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	imx_print_silicon_rev("i.MX51", mx51_revision());
 	clk_disable_unprepare(clk[iim_gate]);
 
+	/*
+	 * Reference Manual says: Functionality of CCDR[18] and CLPCR[23] is no
+	 * longer supported. Set to one for better power saving.
+	 *
+	 * The effect of not setting these bits is that MIPI clocks can't be
+	 * enabled without the IPU clock being enabled aswell.
+	 */
+	val = readl(MXC_CCM_CCDR);
+	val |= 1 << 18;
+	writel(val, MXC_CCM_CCDR);
+
+	val = readl(MXC_CCM_CLPCR);
+	val |= 1 << 23;
+	writel(val, MXC_CCM_CLPCR);
+
 	return 0;
 }
 
-- 
cgit v1.2.3


From 027c0a6af42efa4f2f6034421349bd26a3ca4923 Mon Sep 17 00:00:00 2001
From: Fabio Estevam
Date: Mon, 26 Nov 2012 14:11:22 -0200
Subject: ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices

Move platform-mx2-emma to arch/arm/mach-imx/devices and fix the following build
error:

make[2]: *** No rule to make target `arch/arm/mach-imx/devices/platform-mx2-emma.o', needed by `arch/arm/mach-imx/devices/built-in.o'.  Stop.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-imx/devices/platform-mx2-emma.c | 40 +++++++++++++++++++++++++++
 arch/arm/plat-mxc/devices/platform-mx2-emma.c | 40 ---------------------------
 2 files changed, 40 insertions(+), 40 deletions(-)
 create mode 100644 arch/arm/mach-imx/devices/platform-mx2-emma.c
 delete mode 100644 arch/arm/plat-mxc/devices/platform-mx2-emma.c

diff --git a/arch/arm/mach-imx/devices/platform-mx2-emma.c b/arch/arm/mach-imx/devices/platform-mx2-emma.c
new file mode 100644
index 000000000000..11bd01d402f2
--- /dev/null
+++ b/arch/arm/mach-imx/devices/platform-mx2-emma.c
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2010 Pengutronix
+ * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ */
+#include "../hardware.h"
+#include "devices-common.h"
+
+#define imx_mx2_emmaprp_data_entry_single(soc)				\
+	{								\
+		.iobase = soc ## _EMMAPRP_BASE_ADDR,			\
+		.iosize = SZ_32,					\
+		.irq = soc ## _INT_EMMAPRP,				\
+	}
+
+#ifdef CONFIG_SOC_IMX27
+const struct imx_mx2_emma_data imx27_mx2_emmaprp_data __initconst =
+	imx_mx2_emmaprp_data_entry_single(MX27);
+#endif /* ifdef CONFIG_SOC_IMX27 */
+
+struct platform_device *__init imx_add_mx2_emmaprp(
+		const struct imx_mx2_emma_data *data)
+{
+	struct resource res[] = {
+		{
+			.start = data->iobase,
+			.end = data->iobase + data->iosize - 1,
+			.flags = IORESOURCE_MEM,
+		}, {
+			.start = data->irq,
+			.end = data->irq,
+			.flags = IORESOURCE_IRQ,
+		},
+	};
+	return imx_add_platform_device_dmamask("m2m-emmaprp", 0,
+			res, 2, NULL, 0, DMA_BIT_MASK(32));
+}
diff --git a/arch/arm/plat-mxc/devices/platform-mx2-emma.c b/arch/arm/plat-mxc/devices/platform-mx2-emma.c
deleted file mode 100644
index 508404ddd4ea..000000000000
--- a/arch/arm/plat-mxc/devices/platform-mx2-emma.c
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or modify it under
- * the terms of the GNU General Public License version 2 as published by the
- * Free Software Foundation.
- */
-#include <mach/hardware.h>
-#include <mach/devices-common.h>
-
-#define imx_mx2_emmaprp_data_entry_single(soc)				\
-	{								\
-		.iobase = soc ## _EMMAPRP_BASE_ADDR,			\
-		.iosize = SZ_32,					\
-		.irq = soc ## _INT_EMMAPRP,				\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mx2_emma_data imx27_mx2_emmaprp_data __initconst =
-	imx_mx2_emmaprp_data_entry_single(MX27);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_mx2_emmaprp(
-		const struct imx_mx2_emma_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask("m2m-emmaprp", 0,
-			res, 2, NULL, 0, DMA_BIT_MASK(32));
-}
-- 
cgit v1.2.3


From d0c2e4e4676431c8b25f034d2e3fe041542a5281 Mon Sep 17 00:00:00 2001
From: Olof Johansson
Date: Sat, 15 Dec 2012 09:43:47 -0800
Subject: ARM: exynos: Fix warning due to missing 'inline' in stub

In file included from arch/arm/mach-exynos/clock-exynos5.c:29:0:
arch/arm/mach-exynos/common.h:28:12: warning: 'exynos_pm_late_initcall' defined but not used [-Wunused-function]

Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
---
 arch/arm/mach-exynos/common.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
index dac146df79ac..04744f9c120f 100644
--- a/arch/arm/mach-exynos/common.h
+++ b/arch/arm/mach-exynos/common.h
@@ -25,7 +25,7 @@ void exynos_init_late(void);
 #ifdef CONFIG_PM_GENERIC_DOMAINS
 int exynos_pm_late_initcall(void);
 #else
-static int exynos_pm_late_initcall(void) { return 0; }
+static inline int exynos_pm_late_initcall(void) { return 0; }
 #endif
 
 #ifdef CONFIG_ARCH_EXYNOS4
-- 
cgit v1.2.3


From 6a2461a49dad961c1a7feea6617bf8252826ee3f Mon Sep 17 00:00:00 2001
From: Olof Johansson
Date: Sat, 15 Dec 2012 11:10:25 -0800
Subject: ARM: davinci: fix build break due to missing include

arch/arm/mach-davinci/board-da850-evm.c: In function 'da850_evm_init':
arch/arm/mach-davinci/board-da850-evm.c:1516:2: error: implicit declaration of function 'sram_get_gen_pool' [-Werror=implicit-function-declaration]
arch/arm/mach-davinci/board-da850-evm.c:1516:31: warning: assignment makes pointer from integer without a cast [enabled by default]

Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
---
 arch/arm/mach-davinci/board-da850-evm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 7211772edd9d..0299915575a8 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -41,6 +41,7 @@
 #include <mach/cp_intc.h>
 #include <mach/da8xx.h>
 #include <mach/mux.h>
+#include <mach/sram.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
-- 
cgit v1.2.3


From 761dc26d439e6195462a0257d6cf92c251d50198 Mon Sep 17 00:00:00 2001
From: Linus Walleij
Date: Fri, 14 Dec 2012 15:17:02 +0100
Subject: ARM: u300: delete custom pin hog code

With recent changes in the kernel, the MMCI and PL011 UART
drivers will autonomously request their pins to be muxed in,
so this machine-specific pin hogging code is just interfering
with the proper mechanism and causing regressions in the v3.8
kernel. Delete it and the problems go away.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
---
 arch/arm/mach-u300/core.c | 34 ----------------------------------
 1 file changed, 34 deletions(-)

diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 12f3994c43db..0374b9863e9b 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -27,7 +27,6 @@
 #include <linux/mtd/nand.h>
 #include <linux/mtd/fsmc.h>
 #include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/consumer.h>
 #include <linux/pinctrl/pinconf-generic.h>
 #include <linux/dma-mapping.h>
 #include <linux/platform_data/clk-u300.h>
@@ -1543,39 +1542,6 @@ static struct pinctrl_map __initdata u300_pinmux_map[] = {
 				    pin_highz_conf),
 };
 
-struct u300_mux_hog {
-	struct device *dev;
-	struct pinctrl *p;
-};
-
-static struct u300_mux_hog u300_mux_hogs[] = {
-	{
-		.dev = &uart0_device.dev,
-	},
-	{
-		.dev = &mmcsd_device.dev,
-	},
-};
-
-static int __init u300_pinctrl_fetch(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(u300_mux_hogs); i++) {
-		struct pinctrl *p;
-
-		p = pinctrl_get_select_default(u300_mux_hogs[i].dev);
-		if (IS_ERR(p)) {
-			pr_err("u300: could not get pinmux hog for dev %s\n",
-			       dev_name(u300_mux_hogs[i].dev));
-			continue;
-		}
-		u300_mux_hogs[i].p = p;
-	}
-	return 0;
-}
-subsys_initcall(u300_pinctrl_fetch);
-
 /*
  * Notice that AMBA devices are initialized before platform devices.
  *
-- 
cgit v1.2.3


From 2cdda350672dc30e1530ab562f96dae4d843d145 Mon Sep 17 00:00:00 2001
From: Linus Walleij
Date: Fri, 14 Dec 2012 16:26:28 +0100
Subject: ARM: ux500: fix missing include

Commit db298da2c31e1dcf7c9b7c9cef6217ad3449ebb7
"ARM: nomadik: move platform_data definition"
moved the Ux500-specific musb header from <mach/usb.h>
to <linux/platform_data/usb-musb-ux500.h>

However that makes some board code fail to compile
now:

CC      arch/arm/mach-ux500/board-mop500.o
linux/arch/arm/mach-ux500/cpu-db8500.c: In function 'u8500_init_devices':
linux/arch/arm/mach-ux500/cpu-db8500.c:226:2: error: implicit declaration of function 'ux500_add_usb' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [arch/arm/mach-ux500/cpu-db8500.o] Error 1
make[3]: *** Waiting for unfinished jobs....
make[2]: *** [arch/arm/mach-ux500] Error 2
make[2]: *** Waiting for unfinished jobs....

So fix this up by adding the proper include file that
appears to have been brought in implicitly one or another
way in the past.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
---
 arch/arm/mach-ux500/devices-db8500.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-ux500/devices-db8500.h b/arch/arm/mach-ux500/devices-db8500.h
index 4b24c9992654..a5e05f6e256f 100644
--- a/arch/arm/mach-ux500/devices-db8500.h
+++ b/arch/arm/mach-ux500/devices-db8500.h
@@ -8,6 +8,7 @@
 #ifndef __DEVICES_DB8500_H
 #define __DEVICES_DB8500_H
 
+#include <linux/platform_data/usb-musb-ux500.h>
 #include <mach/irqs.h>
 #include "devices-common.h"
 
-- 
cgit v1.2.3


From 68136b105cbb798b13e9545b9952e568d04e347c Mon Sep 17 00:00:00 2001
From: Maxime Ripard
Date: Wed, 12 Dec 2012 17:08:23 +0100
Subject: ARM: sunxi: Change device tree naming scheme for sunxi

There is several different SoCs sharing the sun5i codename: A10s, A12
and A13. Since there is enough differences to not consider those the
same SoCs, change a bit the naming scheme to reflect this.

Moreover, some boards like the olinuxino come in A10s and A13 variants,
which also share the same SoC codename.

So change the naming scheme to reflect both the codename and the market
name of the SoCs used in the dtsi and in the board files

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
---
 arch/arm/boot/dts/Makefile             | 4 ++--
 arch/arm/boot/dts/sun4i-cubieboard.dts | 4 ++--
 arch/arm/boot/dts/sun5i-olinuxino.dts  | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0f441740c22a..ca6fb8e7f17d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -131,8 +131,8 @@ dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \
 	spear320-evb.dtb \
 	spear320-hmi.dtb
 dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
-dtb-$(CONFIG_ARCH_SUNXI) += sun4i-cubieboard.dtb \
-	sun5i-olinuxino.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun4i-a10-cubieboard.dtb \
+	sun5i-a13-olinuxino.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
diff --git a/arch/arm/boot/dts/sun4i-cubieboard.dts b/arch/arm/boot/dts/sun4i-cubieboard.dts
index f4ca126ad994..5cab82540437 100644
--- a/arch/arm/boot/dts/sun4i-cubieboard.dts
+++ b/arch/arm/boot/dts/sun4i-cubieboard.dts
@@ -11,11 +11,11 @@
  */
 
 /dts-v1/;
-/include/ "sun4i.dtsi"
+/include/ "sun4i-a10.dtsi"
 
 / {
 	model = "Cubietech Cubieboard";
-	compatible = "cubietech,cubieboard", "allwinner,sun4i";
+	compatible = "cubietech,a10-cubieboard", "allwinner,sun4i-a10";
 
 	aliases {
 		serial0 = &uart0;
diff --git a/arch/arm/boot/dts/sun5i-olinuxino.dts b/arch/arm/boot/dts/sun5i-olinuxino.dts
index d6ff889a5d87..498a091a4ea2 100644
--- a/arch/arm/boot/dts/sun5i-olinuxino.dts
+++ b/arch/arm/boot/dts/sun5i-olinuxino.dts
@@ -12,11 +12,11 @@
  */
 
 /dts-v1/;
-/include/ "sun5i.dtsi"
+/include/ "sun5i-a13.dtsi"
 
 / {
 	model = "Olimex A13-Olinuxino";
-	compatible = "olimex,a13-olinuxino", "allwinner,sun5i";
+	compatible = "olimex,a13-olinuxino", "allwinner,sun5i-a13";
 
 	chosen {
 		bootargs = "earlyprintk console=ttyS0,115200";
-- 
cgit v1.2.3