From 5ac04bf190e6f8b17238aef179ebd7f2bdfec919 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Wed, 3 Aug 2011 16:46:48 +0800 Subject: xHCI: fix port U3 status check condition Fix the port U3 status check when Clear PORT_SUSPEND Feature. The port status should be masked with PORT_PLS_MASK to check if it's in U3 state. This should be backported to kernels as old as 2.6.37. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci-hub.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index 0be788cc2fdb..cddcdccadbf7 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -664,7 +664,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, xhci_dbg(xhci, "PORTSC %04x\n", temp); if (temp & PORT_RESET) goto error; - if (temp & XDEV_U3) { + if ((temp & PORT_PLS_MASK) == XDEV_U3) { if ((temp & PORT_PE) == 0) goto error; -- cgit v1.2.3 From 8a8ff2f9399b23b968901f585ccb5a70a537c5ae Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Wed, 3 Aug 2011 16:46:49 +0800 Subject: xHCI: report USB2 port in resuming as suspend When a USB2 port initiate a remote wakeup, software shall ensure that resume is signaled for at least 20ms, and then write '0' to the PLS field. According to this, xhci driver do the following things: 1. When receive a remote wakeup event in irq_handler, set the resume_done value as jiffies + 20ms, and modify rh_timer to poll root hub status at that time; 2. When receive a GetPortStatus request, if the jiffies is after the resume_done value, clear the resume signal and resume_done. However, if usb_port_resume() is called before the rh_timer triggered, it will indicate the port as Suspend Cleared and skip the clear resume signal part. The device will fail the usb_get_status request in finish_port_resume(), and usbcore will try a reset-resume instead. Device will work OK after reset-resume, but resume_done value is not cleared in this case, and xhci_bus_suspend() will fail because when it finds a non-zero resume_done value, it will regard the port as resuming and return -EBUSY. This causes issue on some platforms that the system fail to suspend after remote wakeup from suspend by USB2 devices connected to xHCI port. To fix this issue, report the port status as suspend if the resume is signaling less that 20ms, and usb_port_resume() will wait 25ms and check port status again, so xHCI driver can clear the resume signaling and resume_done value. This should be backported to kernels as old as 2.6.37. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci-hub.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index cddcdccadbf7..1e96d1f1fe6b 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -463,11 +463,12 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, && (temp & PORT_POWER)) status |= USB_PORT_STAT_SUSPEND; } - if ((temp & PORT_PLS_MASK) == XDEV_RESUME) { + if ((temp & PORT_PLS_MASK) == XDEV_RESUME && + !DEV_SUPERSPEED(temp)) { if ((temp & PORT_RESET) || !(temp & PORT_PE)) goto error; - if (!DEV_SUPERSPEED(temp) && time_after_eq(jiffies, - bus_state->resume_done[wIndex])) { + if (time_after_eq(jiffies, + bus_state->resume_done[wIndex])) { xhci_dbg(xhci, "Resume USB2 port %d\n", wIndex + 1); bus_state->resume_done[wIndex] = 0; @@ -487,6 +488,14 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, xhci_ring_device(xhci, slot_id); bus_state->port_c_suspend |= 1 << wIndex; bus_state->suspended_ports &= ~(1 << wIndex); + } else { + /* + * The resume has been signaling for less than + * 20ms. Report the port status as SUSPEND, + * let the usbcore check port status again + * and clear resume signaling later. + */ + status |= USB_PORT_STAT_SUSPEND; } } if ((temp & PORT_PLS_MASK) == XDEV_U0 -- cgit v1.2.3 From d13565c12828ce0cd2a3862bf6260164a0653352 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Fri, 22 Jul 2011 14:34:34 -0700 Subject: xhci: Fix memory leak during failed enqueue. When the isochronous transfer support was introduced, and the xHCI driver switched to using urb->hcpriv to store an "urb_priv" pointer, a couple of memory leaks were introduced into the URB enqueue function in its error handling paths. xhci_urb_enqueue allocates urb_priv, but it doesn't free it if changing the control endpoint's max packet size fails or the bulk endpoint is in the middle of allocating or deallocating streams. xhci_urb_enqueue also doesn't free urb_priv if any of the four endpoint types' enqueue functions fail. Instead, it expects those functions to free urb_priv if an error occurs. However, the bulk, control, and interrupt enqueue functions do not free urb_priv if the endpoint ring is NULL. It will, however, get freed if prepare_transfer() fails in those enqueue functions. Several of the error paths in the isochronous endpoint enqueue function also fail to free it. xhci_queue_isoc_tx_prepare() doesn't free urb_priv if prepare_ring() indicates there is not enough room for all the isochronous TDs in this URB. If individual isochronous TDs fail to be queued (perhaps due to an endpoint state change), urb_priv is also leaked. This argues that the freeing of urb_priv should be done in the function that allocated it, xhci_urb_enqueue. This patch looks rather ugly, but refactoring the code will have to wait because this patch needs to be backported to stable kernels. This patch should be backported to kernels as old as 2.6.36. Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 5 +---- drivers/usb/host/xhci.c | 21 +++++++++++++++++---- 2 files changed, 18 insertions(+), 8 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 7113d16e2d3a..9d3f9dd1ad28 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2500,11 +2500,8 @@ static int prepare_transfer(struct xhci_hcd *xhci, if (td_index == 0) { ret = usb_hcd_link_urb_to_ep(bus_to_hcd(urb->dev->bus), urb); - if (unlikely(ret)) { - xhci_urb_free_priv(xhci, urb_priv); - urb->hcpriv = NULL; + if (unlikely(ret)) return ret; - } } td->urb = urb; diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 1c4432d8fc10..8e84acff1134 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1085,8 +1085,11 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) if (urb->dev->speed == USB_SPEED_FULL) { ret = xhci_check_maxpacket(xhci, slot_id, ep_index, urb); - if (ret < 0) + if (ret < 0) { + xhci_urb_free_priv(xhci, urb_priv); + urb->hcpriv = NULL; return ret; + } } /* We have a spinlock and interrupts disabled, so we must pass @@ -1097,6 +1100,8 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto dying; ret = xhci_queue_ctrl_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); + if (ret) + goto free_priv; spin_unlock_irqrestore(&xhci->lock, flags); } else if (usb_endpoint_xfer_bulk(&urb->ep->desc)) { spin_lock_irqsave(&xhci->lock, flags); @@ -1117,6 +1122,8 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) ret = xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); } + if (ret) + goto free_priv; spin_unlock_irqrestore(&xhci->lock, flags); } else if (usb_endpoint_xfer_int(&urb->ep->desc)) { spin_lock_irqsave(&xhci->lock, flags); @@ -1124,6 +1131,8 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto dying; ret = xhci_queue_intr_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); + if (ret) + goto free_priv; spin_unlock_irqrestore(&xhci->lock, flags); } else { spin_lock_irqsave(&xhci->lock, flags); @@ -1131,18 +1140,22 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto dying; ret = xhci_queue_isoc_tx_prepare(xhci, GFP_ATOMIC, urb, slot_id, ep_index); + if (ret) + goto free_priv; spin_unlock_irqrestore(&xhci->lock, flags); } exit: return ret; dying: - xhci_urb_free_priv(xhci, urb_priv); - urb->hcpriv = NULL; xhci_dbg(xhci, "Ep 0x%x: URB %p submitted for " "non-responsive xHCI host.\n", urb->ep->desc.bEndpointAddress, urb); + ret = -ESHUTDOWN; +free_priv: + xhci_urb_free_priv(xhci, urb_priv); + urb->hcpriv = NULL; spin_unlock_irqrestore(&xhci->lock, flags); - return -ESHUTDOWN; + return ret; } /* Get the right ring for the given URB. -- cgit v1.2.3 From 522989a27c7badb608155b1f1dea3487ed431f74 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Fri, 29 Jul 2011 12:44:32 -0700 Subject: xhci: Fix failed enqueue in the middle of isoch TD. When an isochronous transfer is enqueued, xhci_queue_isoc_tx_prepare() will ensure that there is enough room on the transfer rings for all of the isochronous TDs for that URB. However, when xhci_queue_isoc_tx() is enqueueing individual isoc TDs, the prepare_transfer() function can fail if the endpoint state has changed to disabled, error, or some other unknown state. With the current code, if Nth TD (not the first TD) fails, the ring is left in a sorry state. The partially enqueued TDs are left on the ring, and the first TRB of the TD is not given back to the hardware. The enqueue pointer is left on the TRB after the last successfully enqueued TD. This means the ring is basically useless. Any new transfers will be enqueued after the failed TDs, which the hardware will never read because the cycle bit indicates it does not own them. The ring will fill up with untransferred TDs, and the endpoint will be basically unusable. The untransferred TDs will also remain on the TD list. Since the td_list is a FIFO, this basically means the ring handler will be waiting on TDs that will never be completed (or worse, dereference memory that doesn't exist any more). Change the code to clean up the isochronous ring after a failed transfer. If the first TD failed, simply return and allow the xhci_urb_enqueue function to free the urb_priv. If the Nth TD failed, first remove the TDs from the td_list. Then convert the TRBs that were enqueued into No-op TRBs. Make sure to flip the cycle bit on all enqueued TRBs (including any link TRBs in the middle or between TDs), but leave the cycle bit of the first TRB (which will show software-owned) intact. Then move the ring enqueue pointer back to the first TRB and make sure to change the xhci_ring's cycle state to what is appropriate for that ring segment. This ensures that the No-op TRBs will be overwritten by subsequent TDs, and the hardware will not start executing random TRBs because the cycle bit was left as hardware-owned. This bug is unlikely to be hit, but it was something I noticed while tracking down the watchdog timer issue. I verified that the fix works by injecting some errors on the 250th isochronous URB queued, although I could not verify that the ring is in the correct state because uvcvideo refused to talk to the device after the first usb_submit_urb() failed. Ring debugging shows that the ring looks correct, however. This patch should be backported to kernels as old as 2.6.36. Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 50 ++++++++++++++++++++++++++++++++++++++------ 1 file changed, 44 insertions(+), 6 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 9d3f9dd1ad28..f72149b666b1 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -514,8 +514,12 @@ void xhci_find_new_dequeue_state(struct xhci_hcd *xhci, (unsigned long long) addr); } +/* flip_cycle means flip the cycle bit of all but the first and last TRB. + * (The last TRB actually points to the ring enqueue pointer, which is not part + * of this TD.) This is used to remove partially enqueued isoc TDs from a ring. + */ static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, - struct xhci_td *cur_td) + struct xhci_td *cur_td, bool flip_cycle) { struct xhci_segment *cur_seg; union xhci_trb *cur_trb; @@ -528,6 +532,12 @@ static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, * leave the pointers intact. */ cur_trb->generic.field[3] &= cpu_to_le32(~TRB_CHAIN); + /* Flip the cycle bit (link TRBs can't be the first + * or last TRB). + */ + if (flip_cycle) + cur_trb->generic.field[3] ^= + cpu_to_le32(TRB_CYCLE); xhci_dbg(xhci, "Cancel (unchain) link TRB\n"); xhci_dbg(xhci, "Address = %p (0x%llx dma); " "in seg %p (0x%llx dma)\n", @@ -541,6 +551,11 @@ static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, cur_trb->generic.field[2] = 0; /* Preserve only the cycle bit of this TRB */ cur_trb->generic.field[3] &= cpu_to_le32(TRB_CYCLE); + /* Flip the cycle bit except on the first or last TRB */ + if (flip_cycle && cur_trb != cur_td->first_trb && + cur_trb != cur_td->last_trb) + cur_trb->generic.field[3] ^= + cpu_to_le32(TRB_CYCLE); cur_trb->generic.field[3] |= cpu_to_le32( TRB_TYPE(TRB_TR_NOOP)); xhci_dbg(xhci, "Cancel TRB %p (0x%llx dma) " @@ -719,7 +734,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, cur_td->urb->stream_id, cur_td, &deq_state); else - td_to_noop(xhci, ep_ring, cur_td); + td_to_noop(xhci, ep_ring, cur_td, false); remove_finished_td: /* * The event handler won't see a completion for this TD anymore, @@ -3223,6 +3238,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, start_trb = &ep_ring->enqueue->generic; start_cycle = ep_ring->cycle_state; + urb_priv = urb->hcpriv; /* Queue the first TRB, even if it's zero-length */ for (i = 0; i < num_tds; i++) { unsigned int total_packet_count; @@ -3246,12 +3262,13 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index, urb->stream_id, trbs_per_td, urb, i, mem_flags); - if (ret < 0) - return ret; + if (ret < 0) { + if (i == 0) + return ret; + goto cleanup; + } - urb_priv = urb->hcpriv; td = urb_priv->td[i]; - for (j = 0; j < trbs_per_td; j++) { u32 remainder = 0; field = TRB_TBC(burst_count) | TRB_TLBPC(residue); @@ -3341,6 +3358,27 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, start_cycle, start_trb); return 0; +cleanup: + /* Clean up a partially enqueued isoc transfer. */ + + for (i--; i >= 0; i--) + list_del(&urb_priv->td[i]->td_list); + + /* Use the first TD as a temporary variable to turn the TDs we've queued + * into No-ops with a software-owned cycle bit. That way the hardware + * won't accidentally start executing bogus TDs when we partially + * overwrite them. td->first_trb and td->start_seg are already set. + */ + urb_priv->td[0]->last_trb = ep_ring->enqueue; + /* Every TRB except the first & last will have its cycle bit flipped. */ + td_to_noop(xhci, ep_ring, urb_priv->td[0], true); + + /* Reset the ring enqueue back to the first TRB and its cycle bit. */ + ep_ring->enqueue = urb_priv->td[0]->first_trb; + ep_ring->enq_seg = urb_priv->td[0]->start_seg; + ep_ring->cycle_state = start_cycle; + usb_hcd_unlink_urb_from_ep(bus_to_hcd(urb->dev->bus), urb); + return ret; } /* -- cgit v1.2.3 From 585df1d90cb07a02ca6c7a7d339e56e46d50dafb Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 2 Aug 2011 15:43:40 -0700 Subject: xhci: Remove TDs from TD lists when URBs are canceled. When a driver tries to cancel an URB, and the host controller is dying, xhci_urb_dequeue will giveback the URB without removing the xhci_tds that comprise that URB from the td_list or the cancelled_td_list. This can cause a race condition between the driver calling URB dequeue and the stop endpoint command watchdog timer. If the timer fires on a dying host, and a driver attempts to resubmit while the watchdog timer has dropped the xhci->lock to giveback a cancelled URB, URBs may be given back by the xhci_urb_dequeue() function. At that point, the URB's priv pointer will be freed and set to NULL, but the TDs will remain on the td_list. This will cause an oops in xhci_giveback_urb_in_irq() when the watchdog timer attempts to loop through the endpoints' td_lists, giving back killed URBs. Make sure that xhci_urb_dequeue() removes TDs from the TD lists and canceled TD lists before it gives back the URB. This patch should be backported to kernels as old as 2.6.36. Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 16 ++++++++-------- drivers/usb/host/xhci.c | 7 +++++++ 2 files changed, 15 insertions(+), 8 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index f72149b666b1..b2d654b7477e 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -741,7 +741,7 @@ remove_finished_td: * so remove it from the endpoint ring's TD list. Keep it in * the cancelled TD list for URB completion later. */ - list_del(&cur_td->td_list); + list_del_init(&cur_td->td_list); } last_unlinked_td = cur_td; xhci_stop_watchdog_timer_in_irq(xhci, ep); @@ -769,7 +769,7 @@ remove_finished_td: do { cur_td = list_entry(ep->cancelled_td_list.next, struct xhci_td, cancelled_td_list); - list_del(&cur_td->cancelled_td_list); + list_del_init(&cur_td->cancelled_td_list); /* Clean up the cancelled URB */ /* Doesn't matter what we pass for status, since the core will @@ -877,9 +877,9 @@ void xhci_stop_endpoint_command_watchdog(unsigned long arg) cur_td = list_first_entry(&ring->td_list, struct xhci_td, td_list); - list_del(&cur_td->td_list); + list_del_init(&cur_td->td_list); if (!list_empty(&cur_td->cancelled_td_list)) - list_del(&cur_td->cancelled_td_list); + list_del_init(&cur_td->cancelled_td_list); xhci_giveback_urb_in_irq(xhci, cur_td, -ESHUTDOWN, "killed"); } @@ -888,7 +888,7 @@ void xhci_stop_endpoint_command_watchdog(unsigned long arg) &temp_ep->cancelled_td_list, struct xhci_td, cancelled_td_list); - list_del(&cur_td->cancelled_td_list); + list_del_init(&cur_td->cancelled_td_list); xhci_giveback_urb_in_irq(xhci, cur_td, -ESHUTDOWN, "killed"); } @@ -1580,10 +1580,10 @@ td_cleanup: else *status = 0; } - list_del(&td->td_list); + list_del_init(&td->td_list); /* Was this TD slated to be cancelled but completed anyway? */ if (!list_empty(&td->cancelled_td_list)) - list_del(&td->cancelled_td_list); + list_del_init(&td->cancelled_td_list); urb_priv->td_cnt++; /* Giveback the urb when all the tds are completed */ @@ -3362,7 +3362,7 @@ cleanup: /* Clean up a partially enqueued isoc transfer. */ for (i--; i >= 0; i--) - list_del(&urb_priv->td[i]->td_list); + list_del_init(&urb_priv->td[i]->td_list); /* Use the first TD as a temporary variable to turn the TDs we've queued * into No-ops with a software-owned cycle bit. That way the hardware diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 8e84acff1134..3a0f695138f4 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1252,6 +1252,13 @@ int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_HALTED)) { xhci_dbg(xhci, "HW died, freeing TD.\n"); urb_priv = urb->hcpriv; + for (i = urb_priv->td_cnt; i < urb_priv->length; i++) { + td = urb_priv->td[i]; + if (!list_empty(&td->td_list)) + list_del_init(&td->td_list); + if (!list_empty(&td->cancelled_td_list)) + list_del_init(&td->cancelled_td_list); + } usb_hcd_unlink_urb_from_ep(hcd, urb); spin_unlock_irqrestore(&xhci->lock, flags); -- cgit v1.2.3 From 567b20e02bc1b2bcd69e8bfc022dec3da3fefb89 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Tue, 12 Jul 2011 19:05:29 +0800 Subject: usb: gadget: s3c2410_udc: fix unterminated platform_device_id table platform_device_id structures need a NULL terminating entry, add it. Signed-off-by: Axel Lin Signed-off-by: Felipe Balbi --- drivers/usb/gadget/s3c2410_udc.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/gadget/s3c2410_udc.c b/drivers/usb/gadget/s3c2410_udc.c index 85c1b0d66293..8d31848aab09 100644 --- a/drivers/usb/gadget/s3c2410_udc.c +++ b/drivers/usb/gadget/s3c2410_udc.c @@ -2060,6 +2060,7 @@ static int s3c2410_udc_resume(struct platform_device *pdev) static const struct platform_device_id s3c_udc_ids[] = { { "s3c2410-usbgadget", }, { "s3c2440-usbgadget", }, + { } }; MODULE_DEVICE_TABLE(platform, s3c_udc_ids); -- cgit v1.2.3 From aba1350fdac7cb52f86e6818addb26d03b3ef9bc Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Tue, 19 Jul 2011 21:47:01 +0200 Subject: usb: gadget: fusb300: remove #if 0 block The code in this block is unused and the Author is fine with removing: | These functions were used to debug unstable hw fifo while developing | fusb300. It's much more stable now. | So these functions can be removed. Cc: "Wendy Yuan-Hsin Chen" Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Felipe Balbi --- drivers/usb/gadget/fusb300_udc.c | 101 --------------------------------------- 1 file changed, 101 deletions(-) diff --git a/drivers/usb/gadget/fusb300_udc.c b/drivers/usb/gadget/fusb300_udc.c index 24a924330c81..4ec888f90002 100644 --- a/drivers/usb/gadget/fusb300_udc.c +++ b/drivers/usb/gadget/fusb300_udc.c @@ -609,107 +609,6 @@ void fusb300_rdcxf(struct fusb300 *fusb300, } } -#if 0 -static void fusb300_dbg_fifo(struct fusb300_ep *ep, - u8 entry, u16 length) -{ - u32 reg; - u32 i = 0; - u32 j = 0; - - reg = ioread32(ep->fusb300->reg + FUSB300_OFFSET_GTM); - reg &= ~(FUSB300_GTM_TST_EP_ENTRY(0xF) | - FUSB300_GTM_TST_EP_NUM(0xF) | FUSB300_GTM_TST_FIFO_DEG); - reg |= (FUSB300_GTM_TST_EP_ENTRY(entry) | - FUSB300_GTM_TST_EP_NUM(ep->epnum) | FUSB300_GTM_TST_FIFO_DEG); - iowrite32(reg, ep->fusb300->reg + FUSB300_OFFSET_GTM); - - for (i = 0; i < (length >> 2); i++) { - if (i * 4 == 1024) - break; - reg = ioread32(ep->fusb300->reg + - FUSB300_OFFSET_BUFDBG_START + i * 4); - printk(KERN_DEBUG" 0x%-8x", reg); - j++; - if ((j % 4) == 0) - printk(KERN_DEBUG "\n"); - } - - if (length % 4) { - reg = ioread32(ep->fusb300->reg + - FUSB300_OFFSET_BUFDBG_START + i * 4); - printk(KERN_DEBUG " 0x%x\n", reg); - } - - if ((j % 4) != 0) - printk(KERN_DEBUG "\n"); - - fusb300_disable_bit(ep->fusb300, FUSB300_OFFSET_GTM, - FUSB300_GTM_TST_FIFO_DEG); -} - -static void fusb300_cmp_dbg_fifo(struct fusb300_ep *ep, - u8 entry, u16 length, u8 *golden) -{ - u32 reg; - u32 i = 0; - u32 golden_value; - u8 *tmp; - - tmp = golden; - - printk(KERN_DEBUG "fusb300_cmp_dbg_fifo (entry %d) : start\n", entry); - - reg = ioread32(ep->fusb300->reg + FUSB300_OFFSET_GTM); - reg &= ~(FUSB300_GTM_TST_EP_ENTRY(0xF) | - FUSB300_GTM_TST_EP_NUM(0xF) | FUSB300_GTM_TST_FIFO_DEG); - reg |= (FUSB300_GTM_TST_EP_ENTRY(entry) | - FUSB300_GTM_TST_EP_NUM(ep->epnum) | FUSB300_GTM_TST_FIFO_DEG); - iowrite32(reg, ep->fusb300->reg + FUSB300_OFFSET_GTM); - - for (i = 0; i < (length >> 2); i++) { - if (i * 4 == 1024) - break; - golden_value = *tmp | *(tmp + 1) << 8 | - *(tmp + 2) << 16 | *(tmp + 3) << 24; - - reg = ioread32(ep->fusb300->reg + - FUSB300_OFFSET_BUFDBG_START + i*4); - - if (reg != golden_value) { - printk(KERN_DEBUG "0x%x : ", (u32)(ep->fusb300->reg + - FUSB300_OFFSET_BUFDBG_START + i*4)); - printk(KERN_DEBUG " golden = 0x%x, reg = 0x%x\n", - golden_value, reg); - } - tmp += 4; - } - - switch (length % 4) { - case 1: - golden_value = *tmp; - case 2: - golden_value = *tmp | *(tmp + 1) << 8; - case 3: - golden_value = *tmp | *(tmp + 1) << 8 | *(tmp + 2) << 16; - default: - break; - - reg = ioread32(ep->fusb300->reg + FUSB300_OFFSET_BUFDBG_START + i*4); - if (reg != golden_value) { - printk(KERN_DEBUG "0x%x:", (u32)(ep->fusb300->reg + - FUSB300_OFFSET_BUFDBG_START + i*4)); - printk(KERN_DEBUG " golden = 0x%x, reg = 0x%x\n", - golden_value, reg); - } - } - - printk(KERN_DEBUG "fusb300_cmp_dbg_fifo : end\n"); - fusb300_disable_bit(ep->fusb300, FUSB300_OFFSET_GTM, - FUSB300_GTM_TST_FIFO_DEG); -} -#endif - static void fusb300_rdfifo(struct fusb300_ep *ep, struct fusb300_request *req, u32 length) -- cgit v1.2.3 From 6a22158c596c1531b143c884d479285ef90608d1 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Tue, 19 Jul 2011 20:21:52 +0200 Subject: usb: gadget: composite: fix bMaxPacketSize for SuperSpeed For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket. This is fine in most cases, however on SuperSpeed bMaxPacketSize0 specifies the exponent instead of the actual size in bytes. The only valid value on SS is 9 which denotes 512 bytes. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Felipe Balbi --- drivers/usb/gadget/composite.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c index 5ef87794fd32..aef47414f5d5 100644 --- a/drivers/usb/gadget/composite.c +++ b/drivers/usb/gadget/composite.c @@ -1079,10 +1079,12 @@ composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) cdev->desc.bMaxPacketSize0 = cdev->gadget->ep0->maxpacket; if (gadget_is_superspeed(gadget)) { - if (gadget->speed >= USB_SPEED_SUPER) + if (gadget->speed >= USB_SPEED_SUPER) { cdev->desc.bcdUSB = cpu_to_le16(0x0300); - else + cdev->desc.bMaxPacketSize0 = 9; + } else { cdev->desc.bcdUSB = cpu_to_le16(0x0210); + } } value = min(w_length, (u16) sizeof cdev->desc); -- cgit v1.2.3 From 74c6f3a42a5af424dd954916a5e69d00271b943a Mon Sep 17 00:00:00 2001 From: Sergei Trofimovich Date: Sun, 17 Jul 2011 18:28:00 +0300 Subject: usb: musb: tusb6010_omap: fix build failure: error: 'musb' undeclared CC drivers/usb/musb/tusb6010_omap.o drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq': drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function) drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.) Signed-off-by: Sergei Trofimovich Signed-off-by: Felipe Balbi --- drivers/usb/musb/tusb6010_omap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/musb/tusb6010_omap.c b/drivers/usb/musb/tusb6010_omap.c index c784e6c03aac..07c8a73dfe41 100644 --- a/drivers/usb/musb/tusb6010_omap.c +++ b/drivers/usb/musb/tusb6010_omap.c @@ -89,7 +89,7 @@ static inline int tusb_omap_use_shared_dmareq(struct tusb_omap_dma_ch *chdat) u32 reg = musb_readl(chdat->tbase, TUSB_DMA_EP_MAP); if (reg != 0) { - dev_dbg(musb->controller, "ep%i dmareq0 is busy for ep%i\n", + dev_dbg(chdat->musb->controller, "ep%i dmareq0 is busy for ep%i\n", chdat->epnum, reg & 0xf); return -EAGAIN; } -- cgit v1.2.3 From 26e5c3e227d15a44402e1c9ab817fe48142b4b99 Mon Sep 17 00:00:00 2001 From: Rabin Vincent Date: Mon, 18 Jul 2011 18:38:47 +0530 Subject: usb: musb: fix Kconfig After 622859634 (usb: musb: drop a gigantic amount of ifdeferry): - USB_GADGET_MUSB_HDRC is no longer selectable because it depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG options - The Kconfig comment still says "Enable Host or Gadget support to see Inventra options", even though you now need to enable both of them to see Inventra options. Fix the dependency and drop the anyway unnecessary comment. Signed-off-by: Rabin Vincent Signed-off-by: Felipe Balbi --- drivers/usb/gadget/Kconfig | 2 +- drivers/usb/musb/Kconfig | 3 --- 2 files changed, 1 insertion(+), 4 deletions(-) diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index 44b6b40aafb4..5a084b9cfa3c 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -310,7 +310,7 @@ config USB_PXA_U2O # musb builds in ../musb along with host support config USB_GADGET_MUSB_HDRC tristate "Inventra HDRC USB Peripheral (TI, ADI, ...)" - depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG) + depends on USB_MUSB_HDRC select USB_GADGET_DUALSPEED help This OTG-capable silicon IP is used in dual designs including diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index 6192b45959f4..fc34b8b11910 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -3,9 +3,6 @@ # for silicon based on Mentor Graphics INVENTRA designs # -comment "Enable Host or Gadget support to see Inventra options" - depends on !USB && USB_GADGET=n - # (M)HDRC = (Multipoint) Highspeed Dual-Role Controller config USB_MUSB_HDRC depends on USB && USB_GADGET -- cgit v1.2.3 From 71964b9a0c06f2804be3b6ff47fab07a9468ecb4 Mon Sep 17 00:00:00 2001 From: Sebastian Bauer Date: Thu, 21 Jul 2011 15:40:07 +0200 Subject: usb: gadget: hid: don't STALL when processing a HID Descriptor request This is a patch to fix an issue with the HID gadget which, at the moment, returns STALL on a HID descriptor request. Essentially, the patch changes the hid gadget such that a request for the HID descriptor is handled by copying the descriptor into the response buffer, rather than falling through the default case, in which the request is answered by a STALL. Signed-off-by: Sebastian Bauer Acked-by: Peter Korsgaard Signed-off-by: Felipe Balbi --- drivers/usb/gadget/f_hid.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/gadget/f_hid.c b/drivers/usb/gadget/f_hid.c index 403a48bcf560..83a266bdb40e 100644 --- a/drivers/usb/gadget/f_hid.c +++ b/drivers/usb/gadget/f_hid.c @@ -367,6 +367,13 @@ static int hidg_setup(struct usb_function *f, case ((USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_INTERFACE) << 8 | USB_REQ_GET_DESCRIPTOR): switch (value >> 8) { + case HID_DT_HID: + VDBG(cdev, "USB_REQ_GET_DESCRIPTOR: HID\n"); + length = min_t(unsigned short, length, + hidg_desc.bLength); + memcpy(req->buf, &hidg_desc, length); + goto respond; + break; case HID_DT_REPORT: VDBG(cdev, "USB_REQ_GET_DESCRIPTOR: REPORT\n"); length = min_t(unsigned short, length, -- cgit v1.2.3 From 15154962f777e4ab38adb7641ccae92194c9a96b Mon Sep 17 00:00:00 2001 From: Ming Lei Date: Thu, 28 Jul 2011 22:59:53 +0800 Subject: usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1) Obviously, disabling & put regulator and iounmap(hcd->regs) are missed in .remove and failure handling path of .probe, so add them. Signed-off-by: Ming Lei Acked-by: Alan Stern Tested-by: Keshava Munegowda Signed-off-by: Felipe Balbi --- drivers/usb/host/ehci-omap.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index 55a57c23dd0f..45240321ca09 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -98,6 +98,18 @@ static void omap_ehci_soft_phy_reset(struct platform_device *pdev, u8 port) } } +static void disable_put_regulator( + struct ehci_hcd_omap_platform_data *pdata) +{ + int i; + + for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) { + if (pdata->regulator[i]) { + regulator_disable(pdata->regulator[i]); + regulator_put(pdata->regulator[i]); + } + } +} /* configure so an HC device and id are always provided */ /* always called with process context; sleeping is OK */ @@ -231,9 +243,11 @@ err_add_hcd: omap_usbhs_disable(dev); err_enable: + disable_put_regulator(pdata); usb_put_hcd(hcd); err_io: + iounmap(regs); return ret; } @@ -253,6 +267,8 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev) usb_remove_hcd(hcd); omap_usbhs_disable(dev); + disable_put_regulator(dev->platform_data); + iounmap(hcd->regs); usb_put_hcd(hcd); return 0; } -- cgit v1.2.3 From 93e098a8fc02c579875e64001f7a511b7e75a16c Mon Sep 17 00:00:00 2001 From: John Stultz Date: Wed, 20 Jul 2011 17:09:34 -0700 Subject: usb: musb: fix oops on musb_gadget_pullup an 'unhandled fault' is causes when a gadget driver calls usb_gadget_connect() while the USB cable isn't plugged into the OTG port. the fault is caused by an access to MUSB's memory space while its clock is turned off due to pm_runtime kicking in. in order to fix the fault, we enclose musb_gadget_pullup() with pm_runtime_get_sync() ... pm_runtime_put() calls to be sure we will always reach that path with clock turned on. [ balbi@ti.com : simplified commit log; removed few things which didn't belong there ] Cc: stable@kernel.org Reported-by: Zach Pfeffer Signed-off-by: John Stultz Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_gadget.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index b67a062f556b..8c41a2e6ea77 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1698,6 +1698,8 @@ static int musb_gadget_pullup(struct usb_gadget *gadget, int is_on) is_on = !!is_on; + pm_runtime_get_sync(musb->controller); + /* NOTE: this assumes we are sensing vbus; we'd rather * not pullup unless the B-session is active. */ @@ -1707,6 +1709,9 @@ static int musb_gadget_pullup(struct usb_gadget *gadget, int is_on) musb_pullup(musb, is_on); } spin_unlock_irqrestore(&musb->lock, flags); + + pm_runtime_put(musb->controller); + return 0; } -- cgit v1.2.3 From d366d39bab562545ccb4a5931d62d0fd9e6a8ffc Mon Sep 17 00:00:00 2001 From: Per Forlin Date: Tue, 2 Aug 2011 17:33:39 +0200 Subject: usb: musb: ux500: set dma config for both src and dst The dma driver requires both src and dst to be set. This fix is needed in order to run gadget mass storage. Patch is verified on snowball. Signed-off-by: Per Forlin Acked-by: Mian Yousaf Kaukab Acked-by: Linus Walleij Signed-off-by: Felipe Balbi --- drivers/usb/musb/ux500_dma.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/usb/musb/ux500_dma.c b/drivers/usb/musb/ux500_dma.c index cecace411832..23134754b7c0 100644 --- a/drivers/usb/musb/ux500_dma.c +++ b/drivers/usb/musb/ux500_dma.c @@ -133,15 +133,13 @@ static bool ux500_configure_channel(struct dma_channel *channel, DMA_SLAVE_BUSWIDTH_4_BYTES; slave_conf.direction = direction; - if (direction == DMA_FROM_DEVICE) { - slave_conf.src_addr = usb_fifo_addr; - slave_conf.src_addr_width = addr_width; - slave_conf.src_maxburst = 16; - } else { - slave_conf.dst_addr = usb_fifo_addr; - slave_conf.dst_addr_width = addr_width; - slave_conf.dst_maxburst = 16; - } + slave_conf.src_addr = usb_fifo_addr; + slave_conf.src_addr_width = addr_width; + slave_conf.src_maxburst = 16; + slave_conf.dst_addr = usb_fifo_addr; + slave_conf.dst_addr_width = addr_width; + slave_conf.dst_maxburst = 16; + dma_chan->device->device_control(dma_chan, DMA_SLAVE_CONFIG, (unsigned long) &slave_conf); -- cgit v1.2.3 From afbd0749c0507d5fea980b3bfa76efc43af83d60 Mon Sep 17 00:00:00 2001 From: Per Forlin Date: Wed, 3 Aug 2011 14:22:17 +0200 Subject: usb: musb: ux500: replace missing DBG with dev_dbg ux500_dma.c fail to compile becase DBG has been removed from musb_debug. Use dev_dbg for all prints. Cc: stable@vger.kernel.org Signed-off-by: Per Forlin Acked-by: Mian Yousaf Kaukab Signed-off-by: Felipe Balbi --- drivers/usb/musb/ux500_dma.c | 22 ++++++++++++++-------- 1 file changed, 14 insertions(+), 8 deletions(-) diff --git a/drivers/usb/musb/ux500_dma.c b/drivers/usb/musb/ux500_dma.c index 23134754b7c0..ef4333f4bbe0 100644 --- a/drivers/usb/musb/ux500_dma.c +++ b/drivers/usb/musb/ux500_dma.c @@ -65,7 +65,8 @@ static void ux500_tx_work(struct work_struct *data) struct musb *musb = hw_ep->musb; unsigned long flags; - DBG(4, "DMA tx transfer done on hw_ep=%d\n", hw_ep->epnum); + dev_dbg(musb->controller, "DMA tx transfer done on hw_ep=%d\n", + hw_ep->epnum); spin_lock_irqsave(&musb->lock, flags); ux500_channel->channel.actual_len = ux500_channel->cur_len; @@ -84,7 +85,8 @@ static void ux500_rx_work(struct work_struct *data) struct musb *musb = hw_ep->musb; unsigned long flags; - DBG(4, "DMA rx transfer done on hw_ep=%d\n", hw_ep->epnum); + dev_dbg(musb->controller, "DMA rx transfer done on hw_ep=%d\n", + hw_ep->epnum); spin_lock_irqsave(&musb->lock, flags); ux500_channel->channel.actual_len = ux500_channel->cur_len; @@ -116,9 +118,11 @@ static bool ux500_configure_channel(struct dma_channel *channel, enum dma_slave_buswidth addr_width; dma_addr_t usb_fifo_addr = (MUSB_FIFO_OFFSET(hw_ep->epnum) + ux500_channel->controller->phy_base); + struct musb *musb = ux500_channel->controller->private_data; - DBG(4, "packet_sz=%d, mode=%d, dma_addr=0x%x, len=%d is_tx=%d\n", - packet_sz, mode, dma_addr, len, ux500_channel->is_tx); + dev_dbg(musb->controller, + "packet_sz=%d, mode=%d, dma_addr=0x%x, len=%d is_tx=%d\n", + packet_sz, mode, dma_addr, len, ux500_channel->is_tx); ux500_channel->cur_len = len; @@ -164,6 +168,7 @@ static struct dma_channel *ux500_dma_channel_allocate(struct dma_controller *c, struct ux500_dma_controller *controller = container_of(c, struct ux500_dma_controller, controller); struct ux500_dma_channel *ux500_channel = NULL; + struct musb *musb = controller->private_data; u8 ch_num = hw_ep->epnum - 1; u32 max_ch; @@ -190,7 +195,7 @@ static struct dma_channel *ux500_dma_channel_allocate(struct dma_controller *c, ux500_channel->hw_ep = hw_ep; ux500_channel->is_allocated = 1; - DBG(7, "hw_ep=%d, is_tx=0x%x, channel=%d\n", + dev_dbg(musb->controller, "hw_ep=%d, is_tx=0x%x, channel=%d\n", hw_ep->epnum, is_tx, ch_num); return &(ux500_channel->channel); @@ -199,8 +204,9 @@ static struct dma_channel *ux500_dma_channel_allocate(struct dma_controller *c, static void ux500_dma_channel_release(struct dma_channel *channel) { struct ux500_dma_channel *ux500_channel = channel->private_data; + struct musb *musb = ux500_channel->controller->private_data; - DBG(7, "channel=%d\n", ux500_channel->ch_num); + dev_dbg(musb->controller, "channel=%d\n", ux500_channel->ch_num); if (ux500_channel->is_allocated) { ux500_channel->is_allocated = 0; @@ -250,8 +256,8 @@ static int ux500_dma_channel_abort(struct dma_channel *channel) void __iomem *epio = musb->endpoints[ux500_channel->hw_ep->epnum].regs; u16 csr; - DBG(4, "channel=%d, is_tx=%d\n", ux500_channel->ch_num, - ux500_channel->is_tx); + dev_dbg(musb->controller, "channel=%d, is_tx=%d\n", + ux500_channel->ch_num, ux500_channel->is_tx); if (channel->status == MUSB_DMA_STATUS_BUSY) { if (ux500_channel->is_tx) { -- cgit v1.2.3 From f847a79ab3c1faca3022061045cd22e4678c1b1c Mon Sep 17 00:00:00 2001 From: Per Forlin Date: Wed, 3 Aug 2011 15:39:15 +0200 Subject: usb: musb: cppi: fix build errors due to DBG and missing musb variable Replace DBG with dev_dbg and fix invalid access of musb->controller. With this patch cppi_dma builds successfully. Cc: Signed-off-by: Per Forlin Signed-off-by: Felipe Balbi --- drivers/usb/musb/cppi_dma.c | 26 +++++++++++++++++--------- 1 file changed, 17 insertions(+), 9 deletions(-) diff --git a/drivers/usb/musb/cppi_dma.c b/drivers/usb/musb/cppi_dma.c index 149f3f310a0a..318fb4e8a885 100644 --- a/drivers/usb/musb/cppi_dma.c +++ b/drivers/usb/musb/cppi_dma.c @@ -226,8 +226,10 @@ static int cppi_controller_stop(struct dma_controller *c) struct cppi *controller; void __iomem *tibase; int i; + struct musb *musb; controller = container_of(c, struct cppi, controller); + musb = controller->musb; tibase = controller->tibase; /* DISABLE INDIVIDUAL CHANNEL Interrupts */ @@ -289,9 +291,11 @@ cppi_channel_allocate(struct dma_controller *c, u8 index; struct cppi_channel *cppi_ch; void __iomem *tibase; + struct musb *musb; controller = container_of(c, struct cppi, controller); tibase = controller->tibase; + musb = controller->musb; /* ep0 doesn't use DMA; remember cppi indices are 0..N-1 */ index = ep->epnum - 1; @@ -339,7 +343,8 @@ static void cppi_channel_release(struct dma_channel *channel) c = container_of(channel, struct cppi_channel, channel); tibase = c->controller->tibase; if (!c->hw_ep) - dev_dbg(musb->controller, "releasing idle DMA channel %p\n", c); + dev_dbg(c->controller->musb->controller, + "releasing idle DMA channel %p\n", c); else if (!c->transmit) core_rxirq_enable(tibase, c->index + 1); @@ -357,10 +362,11 @@ cppi_dump_rx(int level, struct cppi_channel *c, const char *tag) musb_ep_select(base, c->index + 1); - DBG(level, "RX DMA%d%s: %d left, csr %04x, " - "%08x H%08x S%08x C%08x, " - "B%08x L%08x %08x .. %08x" - "\n", + dev_dbg(c->controller->musb->controller, + "RX DMA%d%s: %d left, csr %04x, " + "%08x H%08x S%08x C%08x, " + "B%08x L%08x %08x .. %08x" + "\n", c->index, tag, musb_readl(c->controller->tibase, DAVINCI_RXCPPI_BUFCNT0_REG + 4 * c->index), @@ -387,10 +393,11 @@ cppi_dump_tx(int level, struct cppi_channel *c, const char *tag) musb_ep_select(base, c->index + 1); - DBG(level, "TX DMA%d%s: csr %04x, " - "H%08x S%08x C%08x %08x, " - "F%08x L%08x .. %08x" - "\n", + dev_dbg(c->controller->musb->controller, + "TX DMA%d%s: csr %04x, " + "H%08x S%08x C%08x %08x, " + "F%08x L%08x .. %08x" + "\n", c->index, tag, musb_readw(c->hw_ep->regs, MUSB_TXCSR), @@ -1022,6 +1029,7 @@ static bool cppi_rx_scan(struct cppi *cppi, unsigned ch) int i; dma_addr_t safe2ack; void __iomem *regs = rx->hw_ep->regs; + struct musb *musb = cppi->musb; cppi_dump_rx(6, rx, "/K"); -- cgit v1.2.3 From cf6808cb09e72fa7ee8713bf48219a2eb98da91b Mon Sep 17 00:00:00 2001 From: Kuninori Morimoto Date: Wed, 3 Aug 2011 21:41:26 -0700 Subject: usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h Include dma-mapping.h to fix build of the renesas_usbhs driver | CC drivers/usb/renesas_usbhs/mod_gadget.o | drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map': | drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single' | drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device' | drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error' | drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap': | drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single' | drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu' | make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1 | make[4]: *** [drivers/usb/renesas_usbhs] Error 2 Reported-by: Magnus Damm Signed-off-by: Kuninori Morimoto Signed-off-by: Felipe Balbi --- drivers/usb/renesas_usbhs/mod_gadget.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/renesas_usbhs/mod_gadget.c b/drivers/usb/renesas_usbhs/mod_gadget.c index ba79dbf5adbc..e7101dc31e41 100644 --- a/drivers/usb/renesas_usbhs/mod_gadget.c +++ b/drivers/usb/renesas_usbhs/mod_gadget.c @@ -14,6 +14,7 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA * */ +#include #include #include #include -- cgit v1.2.3 From 240a16e2cd831cb25361b1d1797bd04e8faf8b4f Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Fri, 5 Aug 2011 13:29:49 +0300 Subject: usb: musb: tusb6010: fix compilation earlier commits have broken compilation of tusb6010 glue layer, fix it. Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_core.h | 12 ++++++++---- drivers/usb/musb/musb_regs.h | 6 ++++-- drivers/usb/musb/tusb6010.c | 1 + drivers/usb/musb/tusb6010_omap.c | 1 + 4 files changed, 14 insertions(+), 6 deletions(-) diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 668eeef601ae..b3c065ab9dbc 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -172,7 +172,8 @@ enum musb_g_ep0_state { #endif /* TUSB mapping: "flat" plus ep0 special cases */ -#if defined(CONFIG_USB_MUSB_TUSB6010) +#if defined(CONFIG_USB_MUSB_TUSB6010) || \ + defined(CONFIG_USB_MUSB_TUSB6010_MODULE) #define musb_ep_select(_mbase, _epnum) \ musb_writeb((_mbase), MUSB_INDEX, (_epnum)) #define MUSB_EP_OFFSET MUSB_TUSB_OFFSET @@ -241,7 +242,8 @@ struct musb_hw_ep { void __iomem *fifo; void __iomem *regs; -#ifdef CONFIG_USB_MUSB_TUSB6010 +#if defined(CONFIG_USB_MUSB_TUSB6010) || \ + defined(CONFIG_USB_MUSB_TUSB6010_MODULE) void __iomem *conf; #endif @@ -258,7 +260,8 @@ struct musb_hw_ep { struct dma_channel *tx_channel; struct dma_channel *rx_channel; -#ifdef CONFIG_USB_MUSB_TUSB6010 +#if defined(CONFIG_USB_MUSB_TUSB6010) || \ + defined(CONFIG_USB_MUSB_TUSB6010_MODULE) /* TUSB has "asynchronous" and "synchronous" dma modes */ dma_addr_t fifo_async; dma_addr_t fifo_sync; @@ -356,7 +359,8 @@ struct musb { void __iomem *ctrl_base; void __iomem *mregs; -#ifdef CONFIG_USB_MUSB_TUSB6010 +#if defined(CONFIG_USB_MUSB_TUSB6010) || \ + defined(CONFIG_USB_MUSB_TUSB6010_MODULE) dma_addr_t async; dma_addr_t sync; void __iomem *sync_va; diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h index 82410703dcd3..03f2655af290 100644 --- a/drivers/usb/musb/musb_regs.h +++ b/drivers/usb/musb/musb_regs.h @@ -234,7 +234,8 @@ #define MUSB_TESTMODE 0x0F /* 8 bit */ /* Get offset for a given FIFO from musb->mregs */ -#ifdef CONFIG_USB_MUSB_TUSB6010 +#if defined(CONFIG_USB_MUSB_TUSB6010) || \ + defined(CONFIG_USB_MUSB_TUSB6010_MODULE) #define MUSB_FIFO_OFFSET(epnum) (0x200 + ((epnum) * 0x20)) #else #define MUSB_FIFO_OFFSET(epnum) (0x20 + ((epnum) * 4)) @@ -295,7 +296,8 @@ #define MUSB_FLAT_OFFSET(_epnum, _offset) \ (0x100 + (0x10*(_epnum)) + (_offset)) -#ifdef CONFIG_USB_MUSB_TUSB6010 +#if defined(CONFIG_USB_MUSB_TUSB6010) || \ + defined(CONFIG_USB_MUSB_TUSB6010_MODULE) /* TUSB6010 EP0 configuration register is special */ #define MUSB_TUSB_OFFSET(_epnum, _offset) \ (0x10 + _offset) diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index 9eec41fbf3a4..ec1480191f78 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -18,6 +18,7 @@ #include #include #include +#include #include #include #include diff --git a/drivers/usb/musb/tusb6010_omap.c b/drivers/usb/musb/tusb6010_omap.c index 07c8a73dfe41..b67b4bc596c1 100644 --- a/drivers/usb/musb/tusb6010_omap.c +++ b/drivers/usb/musb/tusb6010_omap.c @@ -20,6 +20,7 @@ #include #include "musb_core.h" +#include "tusb6010.h" #define to_chdat(c) ((struct tusb_omap_dma_ch *)(c)->private_data) -- cgit v1.2.3 From ad50c1b20ff27780afbb8bcd3d153393d360419e Mon Sep 17 00:00:00 2001 From: Bob Liu Date: Fri, 5 Aug 2011 17:33:05 +0800 Subject: usb: musb: blackfin: include prefetch head file After the prefetch/list.h restructure, drivers need to explicitly include linux/prefetch.h in order to use the prefetch() function. Otherwise, the current driver fails to build: drivers/usb/musb/blackfin.c: In function 'musb_write_fifo': drivers/usb/musb/blackfin.c:43: error: implicit declaration of function 'prefetch' Signed-off-by: Bob Liu Signed-off-by: Felipe Balbi --- drivers/usb/musb/blackfin.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c index ae8c39617743..5e7cfba5b079 100644 --- a/drivers/usb/musb/blackfin.c +++ b/drivers/usb/musb/blackfin.c @@ -17,6 +17,7 @@ #include #include #include +#include #include -- cgit v1.2.3 From bb8070c29ca87ac0aa24e04a1207cc932f62258f Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Fri, 5 Aug 2011 22:14:46 +0200 Subject: usb: gadget: f_phonet: unlock in error case Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Felipe Balbi --- drivers/usb/gadget/f_phonet.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/gadget/f_phonet.c b/drivers/usb/gadget/f_phonet.c index 8f8d3f6cd89e..8f3eab1af885 100644 --- a/drivers/usb/gadget/f_phonet.c +++ b/drivers/usb/gadget/f_phonet.c @@ -434,6 +434,7 @@ static int pn_set_alt(struct usb_function *f, unsigned intf, unsigned alt) config_ep_by_speed(gadget, f, fp->out_ep)) { fp->in_ep->desc = NULL; fp->out_ep->desc = NULL; + spin_unlock(&port->lock); return -EINVAL; } usb_ep_enable(fp->out_ep); -- cgit v1.2.3 From 6193d6997c90535af8f8491fc0019f785a3322b0 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Wed, 10 Aug 2011 11:01:57 +0200 Subject: usb: musb: gadget: fix error path In case one "forgot" to load the receiver i.e. doing |modprobe omap2430 |modprobe musb_hdrc he ends up with: |musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) |HS USB OTG: no transceiver configured |musb-hdrc musb-hdrc: musb_init_controller failed with status -19 |(NULL device *): gadget not registered. |Unable to handle kernel NULL pointer dereference at virtual address 0000001c |Internal error: Oops: 17 [#1] SMP |[] (sysfs_find_dirent+0x4/0x60) from [] (sysfs_get_dirent+0x28/0x78) |[] (sysfs_get_dirent+0x28/0x78) from [] (sysfs_unmerge_group+0x1c/0x90) |[] (sysfs_unmerge_group+0x1c/0x90) from [] (dpm_sysfs_remove+0x14/0x3c) |[] (dpm_sysfs_remove+0x14/0x3c) from [] (device_del+0x40/0x1b4) |[] (device_del+0x40/0x1b4) from [] (device_unregister+0xc/0x18) |[] (device_unregister+0xc/0x18) from [] (musb_free+0x24/0x88 [musb_hdrc]) |[] (musb_free+0x24/0x88 [musb_hdrc]) from [] (musb_probe+0xb50/0xe3c [musb_hdrc]) |[] (musb_probe+0xb50/0xe3c [musb_hdrc]) from [] (platform_drv_probe+0x1c/0x24) The problem is that musb_free() tries to figure out what was initializued and what wasn't and clean up only the initialized part. This works well for usb_del_gadget_udc() but device_unregister() can't deal with it. Therefore we rely on the fact the we always have a parent device and only then remove the device. I broke this in 0f91349 ("usb: gadget: convert all users to the new udc infrastructure") Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_gadget.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 8c41a2e6ea77..e81820370d6f 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1856,6 +1856,7 @@ int __init musb_gadget_setup(struct musb *musb) return 0; err: + musb->g.dev.parent = NULL; device_unregister(&musb->g.dev); return status; } @@ -1863,7 +1864,8 @@ err: void musb_gadget_cleanup(struct musb *musb) { usb_del_gadget_udc(&musb->g); - device_unregister(&musb->g.dev); + if (musb->g.dev.parent) + device_unregister(&musb->g.dev); } /* -- cgit v1.2.3 From 8a9af4fdf6d5eeb3200a088354d266a87e8260b0 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 9 Aug 2011 16:31:54 -0700 Subject: USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth. usb_ifnum_to_if() can return NULL if the USB device does not have a configuration installed (usb_device->actconfig == NULL), or if we can't find the interface number in the installed configuration. Return an error instead of crashing. Signed-off-by: Sarah Sharp --- drivers/usb/core/hcd.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index 8669ba3fe794..73cbbd85219f 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -1775,6 +1775,8 @@ int usb_hcd_alloc_bandwidth(struct usb_device *udev, struct usb_interface *iface = usb_ifnum_to_if(udev, cur_alt->desc.bInterfaceNumber); + if (!iface) + return -EINVAL; if (iface->resetting_device) { /* * The USB core just reset the device, so the xHCI host -- cgit v1.2.3 From 48df4a6fd8c40c0bbcbca2044f5f2bc75dcf6db1 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Fri, 12 Aug 2011 10:23:01 -0700 Subject: xhci: Handle zero-length isochronous packets. For a long time, the xHCI driver has had this note: /* FIXME: Ignoring zero-length packets, can those happen? */ It turns out that, yes, there are drivers that need to queue zero-length transfers for isochronous OUT transfers. Without this patch, users will see kernel hang messages when a driver attempts to enqueue an isochronous URB with a zero length transfer (because count_isoc_trbs_needed will return zero for that TD, xhci_td->last_trb will never be set, and updating the dequeue pointer will cause an infinite loop). Matěj ran into this issue when using an NI Audio4DJ USB soundcard with the snd-usb-caiaq driver. See https://bugzilla.kernel.org/show_bug.cgi?id=40702 Fix count_isoc_trbs_needed() to return 1 for zero-length transfers (thanks Alan on the math help). Update the various TRB field calculations to deal with zero-length transfers. We're still transferring one packet with a zero-length data payload, so the total_packet_count should be 1. The Transfer Burst Count (TBC) and Transfer Last Burst Packet Count (TLBPC) fields should be set to zero. This patch should be backported to kernels as old as 2.6.36. Signed-off-by: Sarah Sharp Tested-by: Matěj Laitl Cc: Daniel Mack Cc: Alan Stern Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index b2d654b7477e..54139a2f06ce 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2684,6 +2684,10 @@ static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len, { int packets_transferred; + /* One TRB with a zero-length data packet. */ + if (running_total == 0 && trb_buff_len == 0) + return 0; + /* All the TRB queueing functions don't count the current TRB in * running_total. */ @@ -3125,20 +3129,15 @@ static int count_isoc_trbs_needed(struct xhci_hcd *xhci, struct urb *urb, int i) { int num_trbs = 0; - u64 addr, td_len, running_total; + u64 addr, td_len; addr = (u64) (urb->transfer_dma + urb->iso_frame_desc[i].offset); td_len = urb->iso_frame_desc[i].length; - running_total = TRB_MAX_BUFF_SIZE - (addr & (TRB_MAX_BUFF_SIZE - 1)); - running_total &= TRB_MAX_BUFF_SIZE - 1; - if (running_total != 0) - num_trbs++; - - while (running_total < td_len) { + num_trbs = DIV_ROUND_UP(td_len + (addr & (TRB_MAX_BUFF_SIZE - 1)), + TRB_MAX_BUFF_SIZE); + if (num_trbs == 0) num_trbs++; - running_total += TRB_MAX_BUFF_SIZE; - } return num_trbs; } @@ -3250,9 +3249,11 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, addr = start_addr + urb->iso_frame_desc[i].offset; td_len = urb->iso_frame_desc[i].length; td_remain_len = td_len; - /* FIXME: Ignoring zero-length packets, can those happen? */ total_packet_count = roundup(td_len, le16_to_cpu(urb->ep->desc.wMaxPacketSize)); + /* A zero-length transfer still involves at least one packet. */ + if (total_packet_count == 0) + total_packet_count++; burst_count = xhci_get_burst_count(xhci, urb->dev, urb, total_packet_count); residue = xhci_get_last_burst_packet_count(xhci, -- cgit v1.2.3 From 0e69d75ccb2f091757b38d4d6a2ed739e06b615e Mon Sep 17 00:00:00 2001 From: Andrew Bird Date: Tue, 16 Aug 2011 13:57:14 -0600 Subject: USB option driver add PID of Huawei Vodafone K3806 This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband modem to option.c. This is necessary so that the driver gets loaded on demand without the intervention of usb_modeswitch. This has the benefit of it becoming available faster and also ensures that the option driver is not bound to a network interface that should be claimed by cdc_ether. Signed-off-by: Andrew Bird Signed-off-by: Alex Chiang Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 815656198914..6e042229e4be 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -148,6 +148,7 @@ static void option_instat_callback(struct urb *urb); #define HUAWEI_PRODUCT_K4505 0x1464 #define HUAWEI_PRODUCT_K3765 0x1465 #define HUAWEI_PRODUCT_E14AC 0x14AC +#define HUAWEI_PRODUCT_K3806 0x14AE #define HUAWEI_PRODUCT_K3770 0x14C9 #define HUAWEI_PRODUCT_K3771 0x14CA #define HUAWEI_PRODUCT_K4510 0x14CB @@ -551,6 +552,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_ETS1220, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3806, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3770, 0xff, 0x02, 0x31) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3770, 0xff, 0x02, 0x32) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3771, 0xff, 0x02, 0x31) }, -- cgit v1.2.3 From 7e1805844da18a37e6d251d286f93c94b52d791e Mon Sep 17 00:00:00 2001 From: Andrew Bird Date: Tue, 16 Aug 2011 13:58:21 -0600 Subject: USB option driver add PID of Huawei Vodafone K4605 This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband modem to option.c. This is necessary so that the driver gets loaded on demand without the intervention of usb_modeswitch. This has the benefit of it becoming available faster and also ensures that the option driver is not bound to a network interface that should be claimed by suitable network driver. Signed-off-by: Andrew Bird Signed-off-by: Alex Chiang Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 6e042229e4be..ab86e0dd7f33 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -149,6 +149,7 @@ static void option_instat_callback(struct urb *urb); #define HUAWEI_PRODUCT_K3765 0x1465 #define HUAWEI_PRODUCT_E14AC 0x14AC #define HUAWEI_PRODUCT_K3806 0x14AE +#define HUAWEI_PRODUCT_K4605 0x14C6 #define HUAWEI_PRODUCT_K3770 0x14C9 #define HUAWEI_PRODUCT_K3771 0x14CA #define HUAWEI_PRODUCT_K4510 0x14CB @@ -553,6 +554,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_ETS1220, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3806, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4605, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3770, 0xff, 0x02, 0x31) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3770, 0xff, 0x02, 0x32) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3771, 0xff, 0x02, 0x31) }, @@ -1136,10 +1138,11 @@ static int option_probe(struct usb_serial *serial, serial->interface->cur_altsetting->desc.bInterfaceClass != 0xff) return -ENODEV; - /* Don't bind network interfaces on Huawei K3765 & K4505 */ + /* Don't bind network interfaces on Huawei K3765, K4505 & K4605 */ if (serial->dev->descriptor.idVendor == HUAWEI_VENDOR_ID && (serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K3765 || - serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K4505) && + serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K4505 || + serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K4605) && serial->interface->cur_altsetting->desc.bInterfaceNumber == 1) return -ENODEV; -- cgit v1.2.3 From d0f2fb2500b1c5fe4967eb45d8c9bc758d7aef80 Mon Sep 17 00:00:00 2001 From: Wang Zhi Date: Wed, 17 Aug 2011 10:39:31 +0800 Subject: USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume(). From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss the action of clearing PORT_RESUME. This will cause unexpected long resume signal on USB bus. Signed-off-by: Wang Zhi Signed-off-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hub.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index e051b30c1847..4c32cb19b405 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -343,7 +343,7 @@ static int ehci_bus_resume (struct usb_hcd *hcd) u32 temp; u32 power_okay; int i; - u8 resume_needed = 0; + unsigned long resume_needed = 0; if (time_before (jiffies, ehci->next_statechange)) msleep(5); @@ -416,7 +416,7 @@ static int ehci_bus_resume (struct usb_hcd *hcd) if (test_bit(i, &ehci->bus_suspended) && (temp & PORT_SUSPEND)) { temp |= PORT_RESUME; - resume_needed = 1; + set_bit(i, &resume_needed); } ehci_writel(ehci, temp, &ehci->regs->port_status [i]); } @@ -431,8 +431,7 @@ static int ehci_bus_resume (struct usb_hcd *hcd) i = HCS_N_PORTS (ehci->hcs_params); while (i--) { temp = ehci_readl(ehci, &ehci->regs->port_status [i]); - if (test_bit(i, &ehci->bus_suspended) && - (temp & PORT_SUSPEND)) { + if (test_bit(i, &resume_needed)) { temp &= ~(PORT_RWC_BITS | PORT_RESUME); ehci_writel(ehci, temp, &ehci->regs->port_status [i]); ehci_vdbg (ehci, "resumed port %d\n", i + 1); -- cgit v1.2.3 From e5d3d4463fb30998385f9e78ab3c7f63b5813000 Mon Sep 17 00:00:00 2001 From: Yulgon Kim Date: Thu, 18 Aug 2011 14:02:45 +0900 Subject: usb: s5p-ehci: fix a NULL pointer deference This patch fixes a NULL pointer deference. A NULL pointer dereference happens since s5p_ehci->hcd field is not initialized yet in probe function. [jg1.han@samsung.com: edit commit message] Signed-off-by: Yulgon Kim Signed-off-by: Jingoo Han Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-s5p.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/host/ehci-s5p.c b/drivers/usb/host/ehci-s5p.c index b3958b3d3163..9e77f1c8bdbd 100644 --- a/drivers/usb/host/ehci-s5p.c +++ b/drivers/usb/host/ehci-s5p.c @@ -86,6 +86,7 @@ static int __devinit s5p_ehci_probe(struct platform_device *pdev) goto fail_hcd; } + s5p_ehci->hcd = hcd; s5p_ehci->clk = clk_get(&pdev->dev, "usbhost"); if (IS_ERR(s5p_ehci->clk)) { -- cgit v1.2.3 From c6eb2d75ffcdfafa37ff010bf467de20d468ef79 Mon Sep 17 00:00:00 2001 From: Gavin.zhu Date: Mon, 22 Aug 2011 13:51:53 -0700 Subject: USB: option: add YUGA device id to driver Signed-off-by: Gavin.zhu Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 92 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 92 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index ab86e0dd7f33..78452baca88b 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -418,6 +418,56 @@ static void option_instat_callback(struct urb *urb); #define SAMSUNG_VENDOR_ID 0x04e8 #define SAMSUNG_PRODUCT_GT_B3730 0x6889 +/* YUGA products www.yuga-info.com*/ +#define YUGA_VENDOR_ID 0x257A +#define YUGA_PRODUCT_CEM600 0x1601 +#define YUGA_PRODUCT_CEM610 0x1602 +#define YUGA_PRODUCT_CEM500 0x1603 +#define YUGA_PRODUCT_CEM510 0x1604 +#define YUGA_PRODUCT_CEM800 0x1605 +#define YUGA_PRODUCT_CEM900 0x1606 + +#define YUGA_PRODUCT_CEU818 0x1607 +#define YUGA_PRODUCT_CEU816 0x1608 +#define YUGA_PRODUCT_CEU828 0x1609 +#define YUGA_PRODUCT_CEU826 0x160A +#define YUGA_PRODUCT_CEU518 0x160B +#define YUGA_PRODUCT_CEU516 0x160C +#define YUGA_PRODUCT_CEU528 0x160D +#define YUGA_PRODUCT_CEU526 0x160F + +#define YUGA_PRODUCT_CWM600 0x2601 +#define YUGA_PRODUCT_CWM610 0x2602 +#define YUGA_PRODUCT_CWM500 0x2603 +#define YUGA_PRODUCT_CWM510 0x2604 +#define YUGA_PRODUCT_CWM800 0x2605 +#define YUGA_PRODUCT_CWM900 0x2606 + +#define YUGA_PRODUCT_CWU718 0x2607 +#define YUGA_PRODUCT_CWU716 0x2608 +#define YUGA_PRODUCT_CWU728 0x2609 +#define YUGA_PRODUCT_CWU726 0x260A +#define YUGA_PRODUCT_CWU518 0x260B +#define YUGA_PRODUCT_CWU516 0x260C +#define YUGA_PRODUCT_CWU528 0x260D +#define YUGA_PRODUCT_CWU526 0x260F + +#define YUGA_PRODUCT_CLM600 0x2601 +#define YUGA_PRODUCT_CLM610 0x2602 +#define YUGA_PRODUCT_CLM500 0x2603 +#define YUGA_PRODUCT_CLM510 0x2604 +#define YUGA_PRODUCT_CLM800 0x2605 +#define YUGA_PRODUCT_CLM900 0x2606 + +#define YUGA_PRODUCT_CLU718 0x2607 +#define YUGA_PRODUCT_CLU716 0x2608 +#define YUGA_PRODUCT_CLU728 0x2609 +#define YUGA_PRODUCT_CLU726 0x260A +#define YUGA_PRODUCT_CLU518 0x260B +#define YUGA_PRODUCT_CLU516 0x260C +#define YUGA_PRODUCT_CLU528 0x260D +#define YUGA_PRODUCT_CLU526 0x260F + /* some devices interfaces need special handling due to a number of reasons */ enum option_blacklist_reason { OPTION_BLACKLIST_NONE = 0, @@ -1009,6 +1059,48 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(CELOT_VENDOR_ID, CELOT_PRODUCT_CT680M) }, /* CT-650 CDMA 450 1xEVDO modem */ { USB_DEVICE(ONDA_VENDOR_ID, ONDA_MT825UP) }, /* ONDA MT825UP modem */ { USB_DEVICE_AND_INTERFACE_INFO(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_GT_B3730, USB_CLASS_CDC_DATA, 0x00, 0x00) }, /* Samsung GT-B3730 LTE USB modem.*/ + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM600) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM610) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM500) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM510) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM800) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM900) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU818) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU816) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU828) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU826) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU518) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU516) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU528) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEU526) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWM600) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWM610) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWM500) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWM510) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWM800) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWM900) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU718) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU716) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU728) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU726) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU518) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU516) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU528) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CWU526) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLM600) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLM610) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLM500) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLM510) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLM800) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLM900) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU718) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU716) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU728) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU726) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU518) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU516) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU528) }, + { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CLU526) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, option_ids); -- cgit v1.2.3 From 6118514e8749105334f46ccec6faf9a439be6cf9 Mon Sep 17 00:00:00 2001 From: Andrew Bird Date: Wed, 17 Aug 2011 00:20:03 +0100 Subject: USB option driver K3765/K4505 avoid CDC_DATA interface Currently the Option driver avoids binding interface 1 on Huawei K3765 and K4505 broadband modems as it should be handled by the cdc_ether driver instead. This patch ensures we don't bind the interface 2 on those devices as that is CDC_DATA. Signed-off-by: Andrew Bird Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 78452baca88b..fe22e90bc879 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -1235,7 +1235,8 @@ static int option_probe(struct usb_serial *serial, (serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K3765 || serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K4505 || serial->dev->descriptor.idProduct == HUAWEI_PRODUCT_K4605) && - serial->interface->cur_altsetting->desc.bInterfaceNumber == 1) + (serial->interface->cur_altsetting->desc.bInterfaceNumber == 1 || + serial->interface->cur_altsetting->desc.bInterfaceNumber == 2)) return -ENODEV; /* Don't bind network interface on Samsung GT-B3730, it is handled by a separate module */ -- cgit v1.2.3 From c96fbdd0ab97235f930ebf24b38fa42a2e3458cf Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Thu, 25 Aug 2011 11:46:58 +0200 Subject: USB: ftdi_sio: add Calao reference board support Calao use on there dev kits a FT2232 where the port 0 is used for the JTAG and port 1 for the UART They use the same VID and PID as FTDI Chip but they program the manufacturer name in the eeprom So use this information to detect it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Cc: Gregory Hermant Cc: Alan Cox Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 20 +++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 78a2cf9551cc..5fc13e717911 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -101,6 +101,7 @@ static int ftdi_jtag_probe(struct usb_serial *serial); static int ftdi_mtxorb_hack_setup(struct usb_serial *serial); static int ftdi_NDI_device_setup(struct usb_serial *serial); static int ftdi_stmclite_probe(struct usb_serial *serial); +static int ftdi_8u2232c_probe(struct usb_serial *serial); static void ftdi_USB_UIRT_setup(struct ftdi_private *priv); static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv); @@ -128,6 +129,10 @@ static struct ftdi_sio_quirk ftdi_stmclite_quirk = { .probe = ftdi_stmclite_probe, }; +static struct ftdi_sio_quirk ftdi_8u2232c_quirk = { + .probe = ftdi_8u2232c_probe, +}; + /* * The 8U232AM has the same API as the sio except for: * - it can support MUCH higher baudrates; up to: @@ -178,7 +183,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_232RL_PID) }, - { USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) , + .driver_info = (kernel_ulong_t)&ftdi_8u2232c_quirk }, { USB_DEVICE(FTDI_VID, FTDI_4232H_PID) }, { USB_DEVICE(FTDI_VID, FTDI_232H_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MICRO_CHAMELEON_PID) }, @@ -1737,6 +1743,18 @@ static int ftdi_jtag_probe(struct usb_serial *serial) return 0; } +static int ftdi_8u2232c_probe(struct usb_serial *serial) +{ + struct usb_device *udev = serial->dev; + + dbg("%s", __func__); + + if (strcmp(udev->manufacturer, "CALAO Systems") == 0) + return ftdi_jtag_probe(serial); + + return 0; +} + /* * First and second port on STMCLiteadaptors is reserved for JTAG interface * and the forth port for pio -- cgit v1.2.3