From f5e9fdaeb3ba48d9a5a6882614f42d0303355fae Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 10 Jul 2015 15:30:46 +0900 Subject: spi: xcomm: Drop owner assignment from i2c_driver i2c_driver does not need to set an owner because i2c_register_driver() will set it. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Mark Brown --- drivers/spi/spi-xcomm.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/spi/spi-xcomm.c b/drivers/spi/spi-xcomm.c index bb478dccf1d8..d0561a8d9f16 100644 --- a/drivers/spi/spi-xcomm.c +++ b/drivers/spi/spi-xcomm.c @@ -241,7 +241,6 @@ static const struct i2c_device_id spi_xcomm_ids[] = { static struct i2c_driver spi_xcomm_driver = { .driver = { .name = "spi-xcomm", - .owner = THIS_MODULE, }, .id_table = spi_xcomm_ids, .probe = spi_xcomm_probe, -- cgit v1.2.3 From 98c7863c36bdf20c07e38d8bea5261902b52f98d Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 30 Jul 2015 18:18:27 +0200 Subject: spi: xcomm: Export I2C module alias information The I2C core always reports the MODALIAS uevent as "i2c: Signed-off-by: Mark Brown --- drivers/spi/spi-xcomm.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/spi/spi-xcomm.c b/drivers/spi/spi-xcomm.c index d0561a8d9f16..3c28e24b10f5 100644 --- a/drivers/spi/spi-xcomm.c +++ b/drivers/spi/spi-xcomm.c @@ -237,6 +237,7 @@ static const struct i2c_device_id spi_xcomm_ids[] = { { "spi-xcomm" }, { }, }; +MODULE_DEVICE_TABLE(i2c, spi_xcomm_ids); static struct i2c_driver spi_xcomm_driver = { .driver = { -- cgit v1.2.3 From f682c4ffd25a19594d21987c19a69fa123242eb7 Mon Sep 17 00:00:00 2001 From: Vignesh R Date: Thu, 20 Aug 2015 16:00:59 +0530 Subject: spi: ti-qspi: use 128 bit transfer mode where possible TI QSPI has four 32 bit data regsiters which can be used to transfer 16 bytes of data at once. The register group QSPI_SPI_DATA_REG_3, QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is treated as a single 128-bit word for shifting data in and out. The bit at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out in case of 128 bit transfer mode. Therefore the first byte to be written to flash should be at QSPI_SPI_DATA_REG_3[31-25] position. Instead of writing 1 byte at a time when interacting with spi-nor flash, make use of all the four registers so that 16 bytes can be transferred in one go. This reduces number of register writes and Word Complete interrupts for a given transfer message size, thereby increasing the write performance. Without this patch the raw flash write speed is ~100KB/s, with this patch the write speed increases to ~400 kB/s on DRA74 EVM. Signed-off-by: Vignesh R Signed-off-by: Mark Brown --- drivers/spi/spi-ti-qspi.c | 34 ++++++++++++++++++++++++++++++---- 1 file changed, 30 insertions(+), 4 deletions(-) diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index 5c0616870358..aa6d284131e0 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -99,6 +99,8 @@ struct ti_qspi { #define QSPI_INVAL (4 << 16) #define QSPI_WC_CMD_INT_EN (1 << 14) #define QSPI_FLEN(n) ((n - 1) << 0) +#define QSPI_WLEN_MAX_BITS 128 +#define QSPI_WLEN_MAX_BYTES 16 /* STATUS REGISTER */ #define BUSY 0x01 @@ -217,14 +219,16 @@ static inline u32 qspi_is_busy(struct ti_qspi *qspi) static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t) { - int wlen, count; + int wlen, count, xfer_len; unsigned int cmd; const u8 *txbuf; + u32 data; txbuf = t->tx_buf; cmd = qspi->cmd | QSPI_WR_SNGL; count = t->len; wlen = t->bits_per_word >> 3; /* in bytes */ + xfer_len = wlen; while (count) { if (qspi_is_busy(qspi)) @@ -234,7 +238,29 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t) case 1: dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %02x\n", cmd, qspi->dc, *txbuf); - writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG); + if (count >= QSPI_WLEN_MAX_BYTES) { + u32 *txp = (u32 *)txbuf; + + data = cpu_to_be32(*txp++); + writel(data, qspi->base + + QSPI_SPI_DATA_REG_3); + data = cpu_to_be32(*txp++); + writel(data, qspi->base + + QSPI_SPI_DATA_REG_2); + data = cpu_to_be32(*txp++); + writel(data, qspi->base + + QSPI_SPI_DATA_REG_1); + data = cpu_to_be32(*txp++); + writel(data, qspi->base + + QSPI_SPI_DATA_REG); + xfer_len = QSPI_WLEN_MAX_BYTES; + cmd |= QSPI_WLEN(QSPI_WLEN_MAX_BITS); + } else { + writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG); + cmd = qspi->cmd | QSPI_WR_SNGL; + xfer_len = wlen; + cmd |= QSPI_WLEN(wlen); + } break; case 2: dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %04x\n", @@ -254,8 +280,8 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t) dev_err(qspi->dev, "write timed out\n"); return -ETIMEDOUT; } - txbuf += wlen; - count -= wlen; + txbuf += xfer_len; + count -= xfer_len; } return 0; -- cgit v1.2.3 From d8c80d49cfa08b83841a3e315fa13dd310bec006 Mon Sep 17 00:00:00 2001 From: Kamlakant Patel Date: Thu, 27 Aug 2015 17:49:28 +0530 Subject: spi/xlp: SPI controller driver for Netlogic XLP SoCs Add SPI Master controller driver for the SPI interface on XLP8XX, XLP3XX, XLP2XX, XLP9XX and XLP5XX family of Netlogic XLP MIPS64 processors. Signed-off-by: Kamlakant Patel Signed-off-by: Mark Brown --- drivers/spi/Kconfig | 11 ++ drivers/spi/Makefile | 1 + drivers/spi/spi-xlp.c | 456 ++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 468 insertions(+) create mode 100644 drivers/spi/spi-xlp.c diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 0cae1694014d..85b33b57c929 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -598,6 +598,17 @@ config SPI_XILINX Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)" +config SPI_XLP + tristate "Netlogic XLP SPI controller driver" + depends on CPU_XLP || COMPILE_TEST + help + Enable support for the SPI controller on the Netlogic XLP SoCs. + Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX + and XLP5XX. + + If you have a Netlogic XLP platform say Y here. + If unsure, say N. + config SPI_XTENSA_XTFPGA tristate "Xtensa SPI controller for xtfpga" depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 1154dbac8f2c..87d43c7bc898 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -88,5 +88,6 @@ obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi-topcliff-pch.o obj-$(CONFIG_SPI_TXX9) += spi-txx9.o obj-$(CONFIG_SPI_XCOMM) += spi-xcomm.o obj-$(CONFIG_SPI_XILINX) += spi-xilinx.o +obj-$(CONFIG_SPI_XLP) += spi-xlp.o obj-$(CONFIG_SPI_XTENSA_XTFPGA) += spi-xtensa-xtfpga.o obj-$(CONFIG_SPI_ZYNQMP_GQSPI) += spi-zynqmp-gqspi.o diff --git a/drivers/spi/spi-xlp.c b/drivers/spi/spi-xlp.c new file mode 100644 index 000000000000..8f04feca6ee3 --- /dev/null +++ b/drivers/spi/spi-xlp.c @@ -0,0 +1,456 @@ +/* + * Copyright (C) 2003-2015 Broadcom Corporation + * All Rights Reserved + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 (GPL v2) + * as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include +#include +#include +#include +#include +#include +#include + +/* SPI Configuration Register */ +#define XLP_SPI_CONFIG 0x00 +#define XLP_SPI_CPHA BIT(0) +#define XLP_SPI_CPOL BIT(1) +#define XLP_SPI_CS_POL BIT(2) +#define XLP_SPI_TXMISO_EN BIT(3) +#define XLP_SPI_TXMOSI_EN BIT(4) +#define XLP_SPI_RXMISO_EN BIT(5) +#define XLP_SPI_CS_LSBFE BIT(10) +#define XLP_SPI_RXCAP_EN BIT(11) + +/* SPI Frequency Divider Register */ +#define XLP_SPI_FDIV 0x04 + +/* SPI Command Register */ +#define XLP_SPI_CMD 0x08 +#define XLP_SPI_CMD_IDLE_MASK 0x0 +#define XLP_SPI_CMD_TX_MASK 0x1 +#define XLP_SPI_CMD_RX_MASK 0x2 +#define XLP_SPI_CMD_TXRX_MASK 0x3 +#define XLP_SPI_CMD_CONT BIT(4) +#define XLP_SPI_XFR_BITCNT_SHIFT 16 + +/* SPI Status Register */ +#define XLP_SPI_STATUS 0x0c +#define XLP_SPI_XFR_PENDING BIT(0) +#define XLP_SPI_XFR_DONE BIT(1) +#define XLP_SPI_TX_INT BIT(2) +#define XLP_SPI_RX_INT BIT(3) +#define XLP_SPI_TX_UF BIT(4) +#define XLP_SPI_RX_OF BIT(5) +#define XLP_SPI_STAT_MASK 0x3f + +/* SPI Interrupt Enable Register */ +#define XLP_SPI_INTR_EN 0x10 +#define XLP_SPI_INTR_DONE BIT(0) +#define XLP_SPI_INTR_TXTH BIT(1) +#define XLP_SPI_INTR_RXTH BIT(2) +#define XLP_SPI_INTR_TXUF BIT(3) +#define XLP_SPI_INTR_RXOF BIT(4) + +/* SPI FIFO Threshold Register */ +#define XLP_SPI_FIFO_THRESH 0x14 + +/* SPI FIFO Word Count Register */ +#define XLP_SPI_FIFO_WCNT 0x18 +#define XLP_SPI_RXFIFO_WCNT_MASK 0xf +#define XLP_SPI_TXFIFO_WCNT_MASK 0xf0 +#define XLP_SPI_TXFIFO_WCNT_SHIFT 4 + +/* SPI Transmit Data FIFO Register */ +#define XLP_SPI_TXDATA_FIFO 0x1c + +/* SPI Receive Data FIFO Register */ +#define XLP_SPI_RXDATA_FIFO 0x20 + +/* SPI System Control Register */ +#define XLP_SPI_SYSCTRL 0x100 +#define XLP_SPI_SYS_RESET BIT(0) +#define XLP_SPI_SYS_CLKDIS BIT(1) +#define XLP_SPI_SYS_PMEN BIT(8) + +#define SPI_CS_OFFSET 0x40 +#define XLP_SPI_TXRXTH 0x80 +#define XLP_SPI_FIFO_SIZE 8 +#define XLP_SPI_MAX_CS 4 +#define XLP_SPI_DEFAULT_FREQ 133333333 +#define XLP_SPI_FDIV_MIN 4 +#define XLP_SPI_FDIV_MAX 65535 +/* + * SPI can transfer only 28 bytes properly at a time. So split the + * transfer into 28 bytes size. + */ +#define XLP_SPI_XFER_SIZE 28 + +struct xlp_spi_priv { + struct device dev; /* device structure */ + void __iomem *base; /* spi registers base address */ + const u8 *tx_buf; /* tx data buffer */ + u8 *rx_buf; /* rx data buffer */ + int tx_len; /* tx xfer length */ + int rx_len; /* rx xfer length */ + int txerrors; /* TXFIFO underflow count */ + int rxerrors; /* RXFIFO overflow count */ + int cs; /* slave device chip select */ + u32 spi_clk; /* spi clock frequency */ + bool cmd_cont; /* cs active */ + struct completion done; /* completion notification */ +}; + +static inline u32 xlp_spi_reg_read(struct xlp_spi_priv *priv, + int cs, int regoff) +{ + return readl(priv->base + regoff + cs * SPI_CS_OFFSET); +} + +static inline void xlp_spi_reg_write(struct xlp_spi_priv *priv, int cs, + int regoff, u32 val) +{ + writel(val, priv->base + regoff + cs * SPI_CS_OFFSET); +} + +static inline void xlp_spi_sysctl_write(struct xlp_spi_priv *priv, + int regoff, u32 val) +{ + writel(val, priv->base + regoff); +} + +/* + * Setup global SPI_SYSCTRL register for all SPI channels. + */ +static void xlp_spi_sysctl_setup(struct xlp_spi_priv *xspi) +{ + int cs; + + for (cs = 0; cs < XLP_SPI_MAX_CS; cs++) + xlp_spi_sysctl_write(xspi, XLP_SPI_SYSCTRL, + XLP_SPI_SYS_RESET << cs); + xlp_spi_sysctl_write(xspi, XLP_SPI_SYSCTRL, XLP_SPI_SYS_PMEN); +} + +static int xlp_spi_setup(struct spi_device *spi) +{ + struct xlp_spi_priv *xspi; + u32 fdiv, cfg; + int cs; + + xspi = spi_master_get_devdata(spi->master); + cs = spi->chip_select; + /* + * The value of fdiv must be between 4 and 65535. + */ + fdiv = DIV_ROUND_UP(xspi->spi_clk, spi->max_speed_hz); + if (fdiv > XLP_SPI_FDIV_MAX) + fdiv = XLP_SPI_FDIV_MAX; + else if (fdiv < XLP_SPI_FDIV_MIN) + fdiv = XLP_SPI_FDIV_MIN; + + xlp_spi_reg_write(xspi, cs, XLP_SPI_FDIV, fdiv); + xlp_spi_reg_write(xspi, cs, XLP_SPI_FIFO_THRESH, XLP_SPI_TXRXTH); + cfg = xlp_spi_reg_read(xspi, cs, XLP_SPI_CONFIG); + if (spi->mode & SPI_CPHA) + cfg |= XLP_SPI_CPHA; + else + cfg &= ~XLP_SPI_CPHA; + if (spi->mode & SPI_CPOL) + cfg |= XLP_SPI_CPOL; + else + cfg &= ~XLP_SPI_CPOL; + if (!(spi->mode & SPI_CS_HIGH)) + cfg |= XLP_SPI_CS_POL; + else + cfg &= ~XLP_SPI_CS_POL; + if (spi->mode & SPI_LSB_FIRST) + cfg |= XLP_SPI_CS_LSBFE; + else + cfg &= ~XLP_SPI_CS_LSBFE; + + cfg |= XLP_SPI_TXMOSI_EN | XLP_SPI_RXMISO_EN; + if (fdiv == 4) + cfg |= XLP_SPI_RXCAP_EN; + xlp_spi_reg_write(xspi, cs, XLP_SPI_CONFIG, cfg); + + return 0; +} + +static void xlp_spi_read_rxfifo(struct xlp_spi_priv *xspi) +{ + u32 rx_data, rxfifo_cnt; + int i, j, nbytes; + + rxfifo_cnt = xlp_spi_reg_read(xspi, xspi->cs, XLP_SPI_FIFO_WCNT); + rxfifo_cnt &= XLP_SPI_RXFIFO_WCNT_MASK; + while (rxfifo_cnt) { + rx_data = xlp_spi_reg_read(xspi, xspi->cs, XLP_SPI_RXDATA_FIFO); + j = 0; + nbytes = min(xspi->rx_len, 4); + for (i = nbytes - 1; i >= 0; i--, j++) + xspi->rx_buf[i] = (rx_data >> (j * 8)) & 0xff; + + xspi->rx_len -= nbytes; + xspi->rx_buf += nbytes; + rxfifo_cnt--; + } +} + +static void xlp_spi_fill_txfifo(struct xlp_spi_priv *xspi) +{ + u32 tx_data, txfifo_cnt; + int i, j, nbytes; + + txfifo_cnt = xlp_spi_reg_read(xspi, xspi->cs, XLP_SPI_FIFO_WCNT); + txfifo_cnt &= XLP_SPI_TXFIFO_WCNT_MASK; + txfifo_cnt >>= XLP_SPI_TXFIFO_WCNT_SHIFT; + while (xspi->tx_len && (txfifo_cnt < XLP_SPI_FIFO_SIZE)) { + j = 0; + tx_data = 0; + nbytes = min(xspi->tx_len, 4); + for (i = nbytes - 1; i >= 0; i--, j++) + tx_data |= xspi->tx_buf[i] << (j * 8); + + xlp_spi_reg_write(xspi, xspi->cs, XLP_SPI_TXDATA_FIFO, tx_data); + xspi->tx_len -= nbytes; + xspi->tx_buf += nbytes; + txfifo_cnt++; + } +} + +static irqreturn_t xlp_spi_interrupt(int irq, void *dev_id) +{ + struct xlp_spi_priv *xspi = dev_id; + u32 stat; + + stat = xlp_spi_reg_read(xspi, xspi->cs, XLP_SPI_STATUS) & + XLP_SPI_STAT_MASK; + if (!stat) + return IRQ_NONE; + + if (stat & XLP_SPI_TX_INT) { + if (xspi->tx_len) + xlp_spi_fill_txfifo(xspi); + if (stat & XLP_SPI_TX_UF) + xspi->txerrors++; + } + + if (stat & XLP_SPI_RX_INT) { + if (xspi->rx_len) + xlp_spi_read_rxfifo(xspi); + if (stat & XLP_SPI_RX_OF) + xspi->rxerrors++; + } + + /* write status back to clear interrupts */ + xlp_spi_reg_write(xspi, xspi->cs, XLP_SPI_STATUS, stat); + if (stat & XLP_SPI_XFR_DONE) + complete(&xspi->done); + + return IRQ_HANDLED; +} + +static void xlp_spi_send_cmd(struct xlp_spi_priv *xspi, int xfer_len, + int cmd_cont) +{ + u32 cmd = 0; + + if (xspi->tx_buf) + cmd |= XLP_SPI_CMD_TX_MASK; + if (xspi->rx_buf) + cmd |= XLP_SPI_CMD_RX_MASK; + if (cmd_cont) + cmd |= XLP_SPI_CMD_CONT; + cmd |= ((xfer_len * 8 - 1) << XLP_SPI_XFR_BITCNT_SHIFT); + xlp_spi_reg_write(xspi, xspi->cs, XLP_SPI_CMD, cmd); +} + +static int xlp_spi_xfer_block(struct xlp_spi_priv *xs, + const unsigned char *tx_buf, + unsigned char *rx_buf, int xfer_len, int cmd_cont) +{ + int timeout; + u32 intr_mask = 0; + + xs->tx_buf = tx_buf; + xs->rx_buf = rx_buf; + xs->tx_len = (xs->tx_buf == NULL) ? 0 : xfer_len; + xs->rx_len = (xs->rx_buf == NULL) ? 0 : xfer_len; + xs->txerrors = xs->rxerrors = 0; + + /* fill TXDATA_FIFO, then send the CMD */ + if (xs->tx_len) + xlp_spi_fill_txfifo(xs); + + xlp_spi_send_cmd(xs, xfer_len, cmd_cont); + + /* + * We are getting some spurious tx interrupts, so avoid enabling + * tx interrupts when only rx is in process. + * Enable all the interrupts in tx case. + */ + if (xs->tx_len) + intr_mask |= XLP_SPI_INTR_TXTH | XLP_SPI_INTR_TXUF | + XLP_SPI_INTR_RXTH | XLP_SPI_INTR_RXOF; + else + intr_mask |= XLP_SPI_INTR_RXTH | XLP_SPI_INTR_RXOF; + + intr_mask |= XLP_SPI_INTR_DONE; + xlp_spi_reg_write(xs, xs->cs, XLP_SPI_INTR_EN, intr_mask); + + timeout = wait_for_completion_timeout(&xs->done, + msecs_to_jiffies(1000)); + /* Disable interrupts */ + xlp_spi_reg_write(xs, xs->cs, XLP_SPI_INTR_EN, 0x0); + if (!timeout) { + dev_err(&xs->dev, "xfer timedout!\n"); + goto out; + } + if (xs->txerrors || xs->rxerrors) + dev_err(&xs->dev, "Over/Underflow rx %d tx %d xfer %d!\n", + xs->rxerrors, xs->txerrors, xfer_len); + + return xfer_len; +out: + return -ETIMEDOUT; +} + +static int xlp_spi_txrx_bufs(struct xlp_spi_priv *xs, struct spi_transfer *t) +{ + int bytesleft, sz; + unsigned char *rx_buf; + const unsigned char *tx_buf; + + tx_buf = t->tx_buf; + rx_buf = t->rx_buf; + bytesleft = t->len; + while (bytesleft) { + if (bytesleft > XLP_SPI_XFER_SIZE) + sz = xlp_spi_xfer_block(xs, tx_buf, rx_buf, + XLP_SPI_XFER_SIZE, 1); + else + sz = xlp_spi_xfer_block(xs, tx_buf, rx_buf, + bytesleft, xs->cmd_cont); + if (sz < 0) + return sz; + bytesleft -= sz; + if (tx_buf) + tx_buf += sz; + if (rx_buf) + rx_buf += sz; + } + return bytesleft; +} + +static int xlp_spi_transfer_one(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *t) +{ + struct xlp_spi_priv *xspi = spi_master_get_devdata(master); + int ret = 0; + + xspi->cs = spi->chip_select; + xspi->dev = spi->dev; + + if (spi_transfer_is_last(master, t)) + xspi->cmd_cont = 0; + else + xspi->cmd_cont = 1; + + if (xlp_spi_txrx_bufs(xspi, t)) + ret = -EIO; + + spi_finalize_current_transfer(master); + return ret; +} + +static int xlp_spi_probe(struct platform_device *pdev) +{ + struct spi_master *master; + struct xlp_spi_priv *xspi; + struct resource *res; + struct clk *clk; + int irq, err; + + xspi = devm_kzalloc(&pdev->dev, sizeof(*xspi), GFP_KERNEL); + if (!xspi) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + xspi->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(xspi->base)) + return PTR_ERR(xspi->base); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "no IRQ resource found\n"); + return -EINVAL; + } + err = devm_request_irq(&pdev->dev, irq, xlp_spi_interrupt, 0, + pdev->name, xspi); + if (err) { + dev_err(&pdev->dev, "unable to request irq %d\n", irq); + return err; + } + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "could not get spi clock\n"); + return -ENODEV; + } + xspi->spi_clk = clk_get_rate(clk); + + master = spi_alloc_master(&pdev->dev, 0); + if (!master) { + dev_err(&pdev->dev, "could not alloc master\n"); + return -ENOMEM; + } + + master->bus_num = 0; + master->num_chipselect = XLP_SPI_MAX_CS; + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; + master->setup = xlp_spi_setup; + master->transfer_one = xlp_spi_transfer_one; + master->dev.of_node = pdev->dev.of_node; + + init_completion(&xspi->done); + spi_master_set_devdata(master, xspi); + xlp_spi_sysctl_setup(xspi); + + /* register spi controller */ + err = devm_spi_register_master(&pdev->dev, master); + if (err) { + dev_err(&pdev->dev, "spi register master failed!\n"); + spi_master_put(master); + return err; + } + + return 0; +} + +static const struct of_device_id xlp_spi_dt_id[] = { + { .compatible = "netlogic,xlp832-spi" }, + { }, +}; + +static struct platform_driver xlp_spi_driver = { + .probe = xlp_spi_probe, + .driver = { + .name = "xlp-spi", + .of_match_table = xlp_spi_dt_id, + }, +}; +module_platform_driver(xlp_spi_driver); + +MODULE_AUTHOR("Kamlakant Patel "); +MODULE_DESCRIPTION("Netlogic XLP SPI controller driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From bf9628373418328daf67b6508fc3713fc6f5067d Mon Sep 17 00:00:00 2001 From: Kamlakant Patel Date: Thu, 27 Aug 2015 17:49:29 +0530 Subject: spi: Add DT bindings documentation for Netlogic XLP SPI controller Add DT bindings documentation for SPI controller driver used by Netlogic XLP MIPS64 SoCs. Signed-off-by: Kamlakant Patel Signed-off-by: Mark Brown --- Documentation/devicetree/bindings/spi/spi-xlp.txt | 39 +++++++++++++++++++++++ 1 file changed, 39 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/spi-xlp.txt diff --git a/Documentation/devicetree/bindings/spi/spi-xlp.txt b/Documentation/devicetree/bindings/spi/spi-xlp.txt new file mode 100644 index 000000000000..40e82d51efec --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xlp.txt @@ -0,0 +1,39 @@ +SPI Master controller for Netlogic XLP MIPS64 SOCs +================================================== + +Currently this SPI controller driver is supported for the following +Netlogic XLP SoCs: + XLP832, XLP316, XLP208, XLP980, XLP532 + +Required properties: +- compatible : Should be "netlogic,xlp832-spi". +- #address-cells : Number of cells required to define a chip select address + on the SPI bus. +- #size-cells : Should be zero. +- reg : Should contain register location and length. +- clocks : Phandle of the spi clock +- interrupts : Interrupt number used by this controller. +- interrupt-parent : Phandle of the parent interrupt controller. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + + spi: xlp_spi@3a100 { + compatible = "netlogic,xlp832-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x3a100 0x100>; + clocks = <&spi_clk>; + interrupts = <34>; + interrupt-parent = <&pic>; + + spi_nor@1 { + compatible = "spansion,s25sl12801"; + #address-cells = <1>; + #size-cells = <1>; + reg = <1>; /* Chip Select */ + spi-max-frequency = <40000000>; + }; +}; -- cgit v1.2.3