From f41fad3cb8b76cc0e5deebd4d535d0c7c7b43b43 Mon Sep 17 00:00:00 2001 From: Vladimir Oltean Date: Mon, 31 May 2021 01:59:38 +0300 Subject: net: dsa: sja1105: always keep RGMII ports in the MAC role In SJA1105, the xMII Mode Parameters Table field called PHY_MAC denotes the 'role' of the port, be it a PHY or a MAC. This makes a difference in the MII and RMII protocols, but RGMII is symmetric, so either PHY or MAC settings result in the same hardware behavior. The SJA1110 is different, and the RGMII ports only work when configured in MAC mode, so keep the port roles in MAC mode unconditionally. Why we had an RGMII port in the PHY role in the first place was because we wanted to have a way in the driver to denote whether RGMII delays should be applied based on the phy-mode property or not. This is already done in sja1105_parse_rgmii_delays() based on an intermediary struct sja1105_dt_port (which contains the port role). So it is a logical fallacy to use the hardware configuration as a scratchpad for driver data, it isn't necessary. We can also remove the gating condition for applying RGMII delays only for ports in the PHY role. The .setup_rgmii_delay() method looks at the priv->rgmii_rx_delay[port] and priv->rgmii_tx_delay[port] properties which are already populated properly (in the case of a port in the MAC role they are false). Removing this condition generates a few more SPI writes for these ports (clearing the RGMII delays) which are perhaps useless for SJA1105P/Q/R/S, where we know that the delays are disabled by default. But for SJA1110, the firmware on the embedded microcontroller might have done something funny, so it's always a good idea to clear the RGMII delays if that's what Linux expects. Signed-off-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: Jakub Kicinski --- drivers/net/dsa/sja1105/sja1105_clocking.c | 7 +------ drivers/net/dsa/sja1105/sja1105_main.c | 8 +++++++- 2 files changed, 8 insertions(+), 7 deletions(-) diff --git a/drivers/net/dsa/sja1105/sja1105_clocking.c b/drivers/net/dsa/sja1105/sja1105_clocking.c index 03173397d950..ae297648611f 100644 --- a/drivers/net/dsa/sja1105/sja1105_clocking.c +++ b/drivers/net/dsa/sja1105/sja1105_clocking.c @@ -566,14 +566,9 @@ static int sja1105_rgmii_clocking_setup(struct sja1105_private *priv, int port, dev_err(dev, "Failed to configure Tx pad registers\n"); return rc; } + if (!priv->info->setup_rgmii_delay) return 0; - /* The role has no hardware effect for RGMII. However we use it as - * a proxy for this interface being a MAC-to-MAC connection, with - * the RGMII internal delays needing to be applied by us. - */ - if (role == XMII_MAC) - return 0; return priv->info->setup_rgmii_delay(priv, port); } diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c index 5beafe003268..84edd054781b 100644 --- a/drivers/net/dsa/sja1105/sja1105_main.c +++ b/drivers/net/dsa/sja1105/sja1105_main.c @@ -218,8 +218,14 @@ unsupported: /* Even though the SerDes port is able to drive SGMII autoneg * like a PHY would, from the perspective of the XMII tables, * the SGMII port should always be put in MAC mode. + * Similarly, RGMII is a symmetric protocol electrically + * speaking, and the 'RGMII PHY' role does not mean anything to + * hardware. Just keep the 'PHY role' notation relevant to the + * driver to mean 'the switch port should apply RGMII delays', + * but unconditionally put the port in the MAC role. */ - if (ports[i].phy_mode == PHY_INTERFACE_MODE_SGMII) + if (ports[i].phy_mode == PHY_INTERFACE_MODE_SGMII || + phy_interface_mode_is_rgmii(ports[i].phy_mode)) mii->phy_mac[i] = XMII_MAC; else mii->phy_mac[i] = ports[i].role; -- cgit v1.2.3