From d2477de7a63a332a8fe75008fa87e05290c5caac Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Thu, 10 Jan 2013 18:25:04 -0500 Subject: drivers/net: delete old 8 bit ISA Racal ni5010 support. These cards were only available in 8bit format, and in addition they only had AUI and BNC(10-Base2) interfaces (i.e. no RJ-45). In fact, they are so rare, that an internet search on these old cards almost comes up empty, unless the "Micom interlan" name is used. This puts them in the equivalent domain as the 3c501, so there should be no strong opposition to the driver removal, as nobody is seriously using 3.9+ with 8 bit ISA hardware. In doing so, the whole "ethernet/racal" category becomes empty, so we clean up the Makefile/Kconfig and subdir appropriately. Cc: Andreas Mohr Cc: Jan-Pascal van Best Signed-off-by: Paul Gortmaker --- MAINTAINERS | 7 ------- 1 file changed, 7 deletions(-) (limited to 'MAINTAINERS') diff --git a/MAINTAINERS b/MAINTAINERS index cd5b31fec01c..88866e6f7b7c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -5370,13 +5370,6 @@ F: include/linux/sunrpc/ F: include/uapi/linux/nfs* F: include/uapi/linux/sunrpc/ -NI5010 NETWORK DRIVER -M: Jan-Pascal van Best -M: Andreas Mohr -L: netdev@vger.kernel.org -S: Maintained -F: drivers/net/ethernet/racal/ni5010.* - NILFS2 FILESYSTEM M: KONISHI Ryusuke L: linux-nilfs@vger.kernel.org -- cgit v1.2.3 From bb37f1223a7ba9e0abf21d5392d0bb4aedce78f5 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Sun, 13 Jan 2013 19:41:14 -0500 Subject: drivers/net: delete old fujitsu based eth16i driver This is another driver for relatively rare 10Mbit hardware that originated in the early 1990's. So we select it for removal at this point in time as well. Cc: Mika Kuoppala Signed-off-by: Paul Gortmaker --- MAINTAINERS | 5 - drivers/net/Space.c | 4 - drivers/net/ethernet/fujitsu/Kconfig | 11 - drivers/net/ethernet/fujitsu/Makefile | 1 - drivers/net/ethernet/fujitsu/eth16i.c | 1483 --------------------------------- 5 files changed, 1504 deletions(-) delete mode 100644 drivers/net/ethernet/fujitsu/eth16i.c (limited to 'MAINTAINERS') diff --git a/MAINTAINERS b/MAINTAINERS index 88866e6f7b7c..a7aadea909df 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2974,11 +2974,6 @@ S: Maintained F: include/linux/netfilter_bridge/ F: net/bridge/ -ETHERTEAM 16I DRIVER -M: Mika Kuoppala -S: Maintained -F: drivers/net/ethernet/fujitsu/eth16i.c - EXT2 FILE SYSTEM M: Jan Kara L: linux-ext4@vger.kernel.org diff --git a/drivers/net/Space.c b/drivers/net/Space.c index e7d916d5232e..15de20bed4fc 100644 --- a/drivers/net/Space.c +++ b/drivers/net/Space.c @@ -45,7 +45,6 @@ extern struct net_device *ne_probe(int unit); extern struct net_device *hp_probe(int unit); extern struct net_device *hp_plus_probe(int unit); extern struct net_device *fmv18x_probe(int unit); -extern struct net_device *eth16i_probe(int unit); extern struct net_device *i82596_probe(int unit); extern struct net_device *ewrk3_probe(int unit); extern struct net_device *e2100_probe(int unit); @@ -139,9 +138,6 @@ static struct devprobe2 isa_probes[] __initdata = { {cs89x0_probe, 0}, #endif #endif -#ifdef CONFIG_ETH16I - {eth16i_probe, 0}, /* ICL EtherTeam 16i/32 */ -#endif #ifdef CONFIG_EWRK3 /* DEC EtherWORKS 3 */ {ewrk3_probe, 0}, #endif diff --git a/drivers/net/ethernet/fujitsu/Kconfig b/drivers/net/ethernet/fujitsu/Kconfig index af114fd51141..c6a87625898a 100644 --- a/drivers/net/ethernet/fujitsu/Kconfig +++ b/drivers/net/ethernet/fujitsu/Kconfig @@ -28,15 +28,4 @@ config PCMCIA_FMVJ18X To compile this driver as a module, choose M here: the module will be called fmvj18x_cs. If unsure, say N. -config ETH16I - tristate "ICL EtherTeam 16i/32 support" - depends on ISA - ---help--- - If you have a network (Ethernet) card of this type, say Y and read - the Ethernet-HOWTO, available from - . - - To compile this driver as a module, choose M here. The module - will be called eth16i. - endif # NET_VENDOR_FUJITSU diff --git a/drivers/net/ethernet/fujitsu/Makefile b/drivers/net/ethernet/fujitsu/Makefile index e54d0af771d0..21561fdcc69f 100644 --- a/drivers/net/ethernet/fujitsu/Makefile +++ b/drivers/net/ethernet/fujitsu/Makefile @@ -2,5 +2,4 @@ # Makefile for the Fujitsu network device drivers. # -obj-$(CONFIG_ETH16I) += eth16i.o obj-$(CONFIG_PCMCIA_FMVJ18X) += fmvj18x_cs.o diff --git a/drivers/net/ethernet/fujitsu/eth16i.c b/drivers/net/ethernet/fujitsu/eth16i.c deleted file mode 100644 index a992d1f7e0d2..000000000000 --- a/drivers/net/ethernet/fujitsu/eth16i.c +++ /dev/null @@ -1,1483 +0,0 @@ -/* eth16i.c An ICL EtherTeam 16i and 32 EISA ethernet driver for Linux - - Written 1994-1999 by Mika Kuoppala - - Copyright (C) 1994-1999 by Mika Kuoppala - Based on skeleton.c and heavily on at1700.c by Donald Becker - - This software may be used and distributed according to the terms - of the GNU General Public License, incorporated herein by reference. - - The author may be reached as miku@iki.fi - - This driver supports following cards : - - ICL EtherTeam 16i - - ICL EtherTeam 32 EISA - (Uses true 32 bit transfers rather than 16i compatibility mode) - - Example Module usage: - insmod eth16i.o io=0x2a0 mediatype=bnc - - mediatype can be one of the following: bnc,tp,dix,auto,eprom - - 'auto' will try to autoprobe mediatype. - 'eprom' will use whatever type defined in eprom. - - I have benchmarked driver with PII/300Mhz as a ftp client - and 486/33Mhz as a ftp server. Top speed was 1128.37 kilobytes/sec. - - Sources: - - skeleton.c a sample network driver core for linux, - written by Donald Becker - - at1700.c a driver for Allied Telesis AT1700, written - by Donald Becker. - - e16iSRV.asm a Netware 3.X Server Driver for ICL EtherTeam16i - written by Markku Viima - - The Fujitsu MB86965 databook. - - Author thanks following persons due to their valueble assistance: - Markku Viima (ICL) - Ari Valve (ICL) - Donald Becker - Kurt Huwig - - Revision history: - - Version Date Description - - 0.01 15.12-94 Initial version (card detection) - 0.02 23.01-95 Interrupt is now hooked correctly - 0.03 01.02-95 Rewrote initialization part - 0.04 07.02-95 Base skeleton done... - Made a few changes to signature checking - to make it a bit reliable. - - fixed bug in tx_buf mapping - - fixed bug in initialization (DLC_EN - wasn't enabled when initialization - was done.) - 0.05 08.02-95 If there were more than one packet to send, - transmit was jammed due to invalid - register write...now fixed - 0.06 19.02-95 Rewrote interrupt handling - 0.07 13.04-95 Wrote EEPROM read routines - Card configuration now set according to - data read from EEPROM - 0.08 23.06-95 Wrote part that tries to probe used interface - port if AUTO is selected - - 0.09 01.09-95 Added module support - - 0.10 04.09-95 Fixed receive packet allocation to work - with kernels > 1.3.x - - 0.20 20.09-95 Added support for EtherTeam32 EISA - - 0.21 17.10-95 Removed the unnecessary extern - init_etherdev() declaration. Some - other cleanups. - - 0.22 22.02-96 Receive buffer was not flushed - correctly when faulty packet was - received. Now fixed. - - 0.23 26.02-96 Made resetting the adapter - more reliable. - - 0.24 27.02-96 Rewrote faulty packet handling in eth16i_rx - - 0.25 22.05-96 kfree() was missing from cleanup_module. - - 0.26 11.06-96 Sometimes card was not found by - check_signature(). Now made more reliable. - - 0.27 23.06-96 Oops. 16 consecutive collisions halted - adapter. Now will try to retransmit - MAX_COL_16 times before finally giving up. - - 0.28 28.10-97 Added dev_id parameter (NULL) for free_irq - - 0.29 29.10-97 Multiple card support for module users - - 0.30 30.10-97 Fixed irq allocation bug. - (request_irq moved from probe to open) - - 0.30a 21.08-98 Card detection made more relaxed. Driver - had problems with some TCP/IP-PROM boots - to find the card. Suggested by - Kurt Huwig - - 0.31 28.08-98 Media interface port can now be selected - with module parameters or kernel - boot parameters. - - 0.32 31.08-98 IRQ was never freed if open/close - pair wasn't called. Now fixed. - - 0.33 10.09-98 When eth16i_open() was called after - eth16i_close() chip never recovered. - Now more shallow reset is made on - close. - - 0.34 29.06-99 Fixed one bad #ifdef. - Changed ioaddr -> io for consistency - - 0.35 01.07-99 transmit,-receive bytes were never - updated in stats. - - Bugs: - In some cases the media interface autoprobing code doesn't find - the correct interface type. In this case you can - manually choose the interface type in DOS with E16IC.EXE which is - configuration software for EtherTeam16i and EtherTeam32 cards. - This is also true for IRQ setting. You cannot use module - parameter to configure IRQ of the card (yet). - - To do: - - Real multicast support - - Rewrite the media interface autoprobing code. Its _horrible_ ! - - Possibly merge all the MB86965 specific code to external - module for use by eth16.c and Donald's at1700.c - - IRQ configuration with module parameter. I will do - this when i will get enough info about setting - irq without configuration utility. -*/ - -static char *version = - "eth16i.c: v0.35 01-Jul-1999 Mika Kuoppala (miku@iki.fi)\n"; - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include - - - -/* Few macros */ -#define BITSET(ioaddr, bnum) ((outb(((inb(ioaddr)) | (bnum)), ioaddr))) -#define BITCLR(ioaddr, bnum) ((outb(((inb(ioaddr)) & (~(bnum))), ioaddr))) - -/* This is the I/O address space for Etherteam 16i adapter. */ -#define ETH16I_IO_EXTENT 32 - -/* Ticks before deciding that transmit has timed out */ -#define TX_TIMEOUT (400*HZ/1000) - -/* Maximum loop count when receiving packets */ -#define MAX_RX_LOOP 20 - -/* Some interrupt masks */ -#define ETH16I_INTR_ON 0xef8a /* Higher is receive mask */ -#define ETH16I_INTR_OFF 0x0000 - -/* Buffers header status byte meanings */ -#define PKT_GOOD BIT(5) -#define PKT_GOOD_RMT BIT(4) -#define PKT_SHORT BIT(3) -#define PKT_ALIGN_ERR BIT(2) -#define PKT_CRC_ERR BIT(1) -#define PKT_RX_BUF_OVERFLOW BIT(0) - -/* Transmit status register (DLCR0) */ -#define TX_STATUS_REG 0 -#define TX_DONE BIT(7) -#define NET_BUSY BIT(6) -#define TX_PKT_RCD BIT(5) -#define CR_LOST BIT(4) -#define TX_JABBER_ERR BIT(3) -#define COLLISION BIT(2) -#define COLLISIONS_16 BIT(1) - -/* Receive status register (DLCR1) */ -#define RX_STATUS_REG 1 -#define RX_PKT BIT(7) /* Packet received */ -#define BUS_RD_ERR BIT(6) -#define SHORT_PKT_ERR BIT(3) -#define ALIGN_ERR BIT(2) -#define CRC_ERR BIT(1) -#define RX_BUF_OVERFLOW BIT(0) - -/* Transmit Interrupt Enable Register (DLCR2) */ -#define TX_INTR_REG 2 -#define TX_INTR_DONE BIT(7) -#define TX_INTR_COL BIT(2) -#define TX_INTR_16_COL BIT(1) - -/* Receive Interrupt Enable Register (DLCR3) */ -#define RX_INTR_REG 3 -#define RX_INTR_RECEIVE BIT(7) -#define RX_INTR_SHORT_PKT BIT(3) -#define RX_INTR_CRC_ERR BIT(1) -#define RX_INTR_BUF_OVERFLOW BIT(0) - -/* Transmit Mode Register (DLCR4) */ -#define TRANSMIT_MODE_REG 4 -#define LOOPBACK_CONTROL BIT(1) -#define CONTROL_OUTPUT BIT(2) - -/* Receive Mode Register (DLCR5) */ -#define RECEIVE_MODE_REG 5 -#define RX_BUFFER_EMPTY BIT(6) -#define ACCEPT_BAD_PACKETS BIT(5) -#define RECEIVE_SHORT_ADDR BIT(4) -#define ACCEPT_SHORT_PACKETS BIT(3) -#define REMOTE_RESET BIT(2) - -#define ADDRESS_FILTER_MODE BIT(1) | BIT(0) -#define REJECT_ALL 0 -#define ACCEPT_ALL 3 -#define MODE_1 1 /* NODE ID, BC, MC, 2-24th bit */ -#define MODE_2 2 /* NODE ID, BC, MC, Hash Table */ - -/* Configuration Register 0 (DLCR6) */ -#define CONFIG_REG_0 6 -#define DLC_EN BIT(7) -#define SRAM_CYCLE_TIME_100NS BIT(6) -#define SYSTEM_BUS_WIDTH_8 BIT(5) /* 1 = 8bit, 0 = 16bit */ -#define BUFFER_WIDTH_8 BIT(4) /* 1 = 8bit, 0 = 16bit */ -#define TBS1 BIT(3) -#define TBS0 BIT(2) -#define SRAM_BS1 BIT(1) /* 00=8kb, 01=16kb */ -#define SRAM_BS0 BIT(0) /* 10=32kb, 11=64kb */ - -#ifndef ETH16I_TX_BUF_SIZE /* 0 = 2kb, 1 = 4kb */ -#define ETH16I_TX_BUF_SIZE 3 /* 2 = 8kb, 3 = 16kb */ -#endif -#define TX_BUF_1x2048 0 -#define TX_BUF_2x2048 1 -#define TX_BUF_2x4098 2 -#define TX_BUF_2x8192 3 - -/* Configuration Register 1 (DLCR7) */ -#define CONFIG_REG_1 7 -#define POWERUP BIT(5) - -/* Transmit start register */ -#define TRANSMIT_START_REG 10 -#define TRANSMIT_START_RB 2 -#define TX_START BIT(7) /* Rest of register bit indicate*/ - /* number of packets in tx buffer*/ -/* Node ID registers (DLCR8-13) */ -#define NODE_ID_0 8 -#define NODE_ID_RB 0 - -/* Hash Table registers (HT8-15) */ -#define HASH_TABLE_0 8 -#define HASH_TABLE_RB 1 - -/* Buffer memory ports */ -#define BUFFER_MEM_PORT_LB 8 -#define DATAPORT BUFFER_MEM_PORT_LB -#define BUFFER_MEM_PORT_HB 9 - -/* 16 Collision control register (BMPR11) */ -#define COL_16_REG 11 -#define HALT_ON_16 0x00 -#define RETRANS_AND_HALT_ON_16 0x02 - -/* Maximum number of attempts to send after 16 concecutive collisions */ -#define MAX_COL_16 10 - -/* DMA Burst and Transceiver Mode Register (BMPR13) */ -#define TRANSCEIVER_MODE_REG 13 -#define TRANSCEIVER_MODE_RB 2 -#define IO_BASE_UNLOCK BIT(7) -#define LOWER_SQUELCH_TRESH BIT(6) -#define LINK_TEST_DISABLE BIT(5) -#define AUI_SELECT BIT(4) -#define DIS_AUTO_PORT_SEL BIT(3) - -/* Filter Self Receive Register (BMPR14) */ -#define FILTER_SELF_RX_REG 14 -#define SKIP_RX_PACKET BIT(2) -#define FILTER_SELF_RECEIVE BIT(0) - -/* EEPROM Control Register (BMPR 16) */ -#define EEPROM_CTRL_REG 16 - -/* EEPROM Data Register (BMPR 17) */ -#define EEPROM_DATA_REG 17 - -/* NMC93CSx6 EEPROM Control Bits */ -#define CS_0 0x00 -#define CS_1 0x20 -#define SK_0 0x00 -#define SK_1 0x40 -#define DI_0 0x00 -#define DI_1 0x80 - -/* NMC93CSx6 EEPROM Instructions */ -#define EEPROM_READ 0x80 - -/* NMC93CSx6 EEPROM Addresses */ -#define E_NODEID_0 0x02 -#define E_NODEID_1 0x03 -#define E_NODEID_2 0x04 -#define E_PORT_SELECT 0x14 - #define E_PORT_BNC 0x00 - #define E_PORT_DIX 0x01 - #define E_PORT_TP 0x02 - #define E_PORT_AUTO 0x03 - #define E_PORT_FROM_EPROM 0x04 -#define E_PRODUCT_CFG 0x30 - - -/* Macro to slow down io between EEPROM clock transitions */ -#define eeprom_slow_io() do { int _i = 40; while(--_i > 0) { inb(0x80); }}while(0) - -/* Jumperless Configuration Register (BMPR19) */ -#define JUMPERLESS_CONFIG 19 - -/* ID ROM registers, writing to them also resets some parts of chip */ -#define ID_ROM_0 24 -#define ID_ROM_7 31 -#define RESET ID_ROM_0 - -/* This is the I/O address list to be probed when seeking the card */ -static unsigned int eth16i_portlist[] __initdata = { - 0x260, 0x280, 0x2A0, 0x240, 0x340, 0x320, 0x380, 0x300, 0 -}; - -static unsigned int eth32i_portlist[] __initdata = { - 0x1000, 0x2000, 0x3000, 0x4000, 0x5000, 0x6000, 0x7000, 0x8000, - 0x9000, 0xA000, 0xB000, 0xC000, 0xD000, 0xE000, 0xF000, 0 -}; - -/* This is the Interrupt lookup table for Eth16i card */ -static unsigned int eth16i_irqmap[] __initdata = { 9, 10, 5, 15, 0 }; -#define NUM_OF_ISA_IRQS 4 - -/* This is the Interrupt lookup table for Eth32i card */ -static unsigned int eth32i_irqmap[] __initdata = { 3, 5, 7, 9, 10, 11, 12, 15, 0 }; -#define EISA_IRQ_REG 0xc89 -#define NUM_OF_EISA_IRQS 8 - -static unsigned int eth16i_tx_buf_map[] = { 2048, 2048, 4096, 8192 }; - -/* Use 0 for production, 1 for verification, >2 for debug */ -#ifndef ETH16I_DEBUG -#define ETH16I_DEBUG 0 -#endif -static unsigned int eth16i_debug = ETH16I_DEBUG; - -/* Information for each board */ - -struct eth16i_local { - unsigned char tx_started; - unsigned char tx_buf_busy; - unsigned short tx_queue; /* Number of packets in transmit buffer */ - unsigned short tx_queue_len; - unsigned int tx_buf_size; - unsigned long open_time; - unsigned long tx_buffered_packets; - unsigned long tx_buffered_bytes; - unsigned long col_16; - spinlock_t lock; -}; - -/* Function prototypes */ - -static int eth16i_probe1(struct net_device *dev, int ioaddr); -static int eth16i_check_signature(int ioaddr); -static int eth16i_probe_port(int ioaddr); -static void eth16i_set_port(int ioaddr, int porttype); -static int eth16i_send_probe_packet(int ioaddr, unsigned char *b, int l); -static int eth16i_receive_probe_packet(int ioaddr); -static int eth16i_get_irq(int ioaddr); -static int eth16i_read_eeprom(int ioaddr, int offset); -static int eth16i_read_eeprom_word(int ioaddr); -static void eth16i_eeprom_cmd(int ioaddr, unsigned char command); -static int eth16i_open(struct net_device *dev); -static int eth16i_close(struct net_device *dev); -static netdev_tx_t eth16i_tx(struct sk_buff *skb, struct net_device *dev); -static void eth16i_rx(struct net_device *dev); -static void eth16i_timeout(struct net_device *dev); -static irqreturn_t eth16i_interrupt(int irq, void *dev_id); -static void eth16i_reset(struct net_device *dev); -static void eth16i_timeout(struct net_device *dev); -static void eth16i_skip_packet(struct net_device *dev); -static void eth16i_multicast(struct net_device *dev); -static void eth16i_select_regbank(unsigned char regbank, int ioaddr); -static void eth16i_initialize(struct net_device *dev, int boot); - -#if 0 -static int eth16i_set_irq(struct net_device *dev); -#endif - -#ifdef MODULE -static ushort eth16i_parse_mediatype(const char* s); -#endif - -static char cardname[] __initdata = "ICL EtherTeam 16i/32"; - -static int __init do_eth16i_probe(struct net_device *dev) -{ - int i; - int ioaddr; - int base_addr = dev->base_addr; - - if(eth16i_debug > 4) - printk(KERN_DEBUG "Probing started for %s\n", cardname); - - if(base_addr > 0x1ff) /* Check only single location */ - return eth16i_probe1(dev, base_addr); - else if(base_addr != 0) /* Don't probe at all */ - return -ENXIO; - - /* Seek card from the ISA io address space */ - for(i = 0; (ioaddr = eth16i_portlist[i]) ; i++) - if(eth16i_probe1(dev, ioaddr) == 0) - return 0; - - /* Seek card from the EISA io address space */ - for(i = 0; (ioaddr = eth32i_portlist[i]) ; i++) - if(eth16i_probe1(dev, ioaddr) == 0) - return 0; - - return -ENODEV; -} - -#ifndef MODULE -struct net_device * __init eth16i_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(sizeof(struct eth16i_local)); - int err; - - if (!dev) - return ERR_PTR(-ENOMEM); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - err = do_eth16i_probe(dev); - if (err) - goto out; - return dev; -out: - free_netdev(dev); - return ERR_PTR(err); -} -#endif - -static const struct net_device_ops eth16i_netdev_ops = { - .ndo_open = eth16i_open, - .ndo_stop = eth16i_close, - .ndo_start_xmit = eth16i_tx, - .ndo_set_rx_mode = eth16i_multicast, - .ndo_tx_timeout = eth16i_timeout, - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -static int __init eth16i_probe1(struct net_device *dev, int ioaddr) -{ - struct eth16i_local *lp = netdev_priv(dev); - static unsigned version_printed; - int retval; - - /* Let's grab the region */ - if (!request_region(ioaddr, ETH16I_IO_EXTENT, cardname)) - return -EBUSY; - - /* - The MB86985 chip has on register which holds information in which - io address the chip lies. First read this register and compare - it to our current io address and if match then this could - be our chip. - */ - - if(ioaddr < 0x1000) { - if(eth16i_portlist[(inb(ioaddr + JUMPERLESS_CONFIG) & 0x07)] - != ioaddr) { - retval = -ENODEV; - goto out; - } - } - - /* Now we will go a bit deeper and try to find the chip's signature */ - - if(eth16i_check_signature(ioaddr) != 0) { - retval = -ENODEV; - goto out; - } - - /* - Now it seems that we have found a ethernet chip in this particular - ioaddr. The MB86985 chip has this feature, that when you read a - certain register it will increase it's io base address to next - configurable slot. Now when we have found the chip, first thing is - to make sure that the chip's ioaddr will hold still here. - */ - - eth16i_select_regbank(TRANSCEIVER_MODE_RB, ioaddr); - outb(0x00, ioaddr + TRANSCEIVER_MODE_REG); - - outb(0x00, ioaddr + RESET); /* Reset some parts of chip */ - BITSET(ioaddr + CONFIG_REG_0, BIT(7)); /* Disable the data link */ - - if( (eth16i_debug & version_printed++) == 0) - printk(KERN_INFO "%s", version); - - dev->base_addr = ioaddr; - dev->irq = eth16i_get_irq(ioaddr); - - /* Try to obtain interrupt vector */ - - if ((retval = request_irq(dev->irq, (void *)ð16i_interrupt, 0, cardname, dev))) { - printk(KERN_WARNING "%s at %#3x, but is unusable due to conflicting IRQ %d.\n", - cardname, ioaddr, dev->irq); - goto out; - } - - printk(KERN_INFO "%s: %s at %#3x, IRQ %d, ", - dev->name, cardname, ioaddr, dev->irq); - - - /* Now we will have to lock the chip's io address */ - eth16i_select_regbank(TRANSCEIVER_MODE_RB, ioaddr); - outb(0x38, ioaddr + TRANSCEIVER_MODE_REG); - - eth16i_initialize(dev, 1); /* Initialize rest of the chip's registers */ - - /* Now let's same some energy by shutting down the chip ;) */ - BITCLR(ioaddr + CONFIG_REG_1, POWERUP); - - /* Initialize the device structure */ - dev->netdev_ops = ð16i_netdev_ops; - dev->watchdog_timeo = TX_TIMEOUT; - spin_lock_init(&lp->lock); - - retval = register_netdev(dev); - if (retval) - goto out1; - return 0; -out1: - free_irq(dev->irq, dev); -out: - release_region(ioaddr, ETH16I_IO_EXTENT); - return retval; -} - - -static void eth16i_initialize(struct net_device *dev, int boot) -{ - int ioaddr = dev->base_addr; - int i, node_w = 0; - unsigned char node_byte = 0; - - /* Setup station address */ - eth16i_select_regbank(NODE_ID_RB, ioaddr); - for(i = 0 ; i < 3 ; i++) { - unsigned short node_val = eth16i_read_eeprom(ioaddr, E_NODEID_0 + i); - ((unsigned short *)dev->dev_addr)[i] = ntohs(node_val); - } - - for(i = 0; i < 6; i++) { - outb( ((unsigned char *)dev->dev_addr)[i], ioaddr + NODE_ID_0 + i); - if(boot) { - printk("%02x", inb(ioaddr + NODE_ID_0 + i)); - if(i != 5) - printk(":"); - } - } - - /* Now we will set multicast addresses to accept none */ - eth16i_select_regbank(HASH_TABLE_RB, ioaddr); - for(i = 0; i < 8; i++) - outb(0x00, ioaddr + HASH_TABLE_0 + i); - - /* - Now let's disable the transmitter and receiver, set the buffer ram - cycle time, bus width and buffer data path width. Also we shall - set transmit buffer size and total buffer size. - */ - - eth16i_select_regbank(2, ioaddr); - - node_byte = 0; - node_w = eth16i_read_eeprom(ioaddr, E_PRODUCT_CFG); - - if( (node_w & 0xFF00) == 0x0800) - node_byte |= BUFFER_WIDTH_8; - - node_byte |= SRAM_BS1; - - if( (node_w & 0x00FF) == 64) - node_byte |= SRAM_BS0; - - node_byte |= DLC_EN | SRAM_CYCLE_TIME_100NS | (ETH16I_TX_BUF_SIZE << 2); - - outb(node_byte, ioaddr + CONFIG_REG_0); - - /* We shall halt the transmitting, if 16 collisions are detected */ - outb(HALT_ON_16, ioaddr + COL_16_REG); - -#ifdef MODULE - /* if_port already set by init_module() */ -#else - dev->if_port = (dev->mem_start < E_PORT_FROM_EPROM) ? - dev->mem_start : E_PORT_FROM_EPROM; -#endif - - /* Set interface port type */ - if(boot) { - static const char * const porttype[] = { - "BNC", "DIX", "TP", "AUTO", "FROM_EPROM" - }; - - switch(dev->if_port) - { - - case E_PORT_FROM_EPROM: - dev->if_port = eth16i_read_eeprom(ioaddr, E_PORT_SELECT); - break; - - case E_PORT_AUTO: - dev->if_port = eth16i_probe_port(ioaddr); - break; - - case E_PORT_BNC: - case E_PORT_TP: - case E_PORT_DIX: - break; - } - - printk(" %s interface.\n", porttype[dev->if_port]); - - eth16i_set_port(ioaddr, dev->if_port); - } - - /* Set Receive Mode to normal operation */ - outb(MODE_2, ioaddr + RECEIVE_MODE_REG); -} - -static int eth16i_probe_port(int ioaddr) -{ - int i; - int retcode; - unsigned char dummy_packet[64]; - - /* Powerup the chip */ - outb(0xc0 | POWERUP, ioaddr + CONFIG_REG_1); - - BITSET(ioaddr + CONFIG_REG_0, DLC_EN); - - eth16i_select_regbank(NODE_ID_RB, ioaddr); - - for(i = 0; i < 6; i++) { - dummy_packet[i] = inb(ioaddr + NODE_ID_0 + i); - dummy_packet[i+6] = inb(ioaddr + NODE_ID_0 + i); - } - - dummy_packet[12] = 0x00; - dummy_packet[13] = 0x04; - memset(dummy_packet + 14, 0, sizeof(dummy_packet) - 14); - - eth16i_select_regbank(2, ioaddr); - - for(i = 0; i < 3; i++) { - BITSET(ioaddr + CONFIG_REG_0, DLC_EN); - BITCLR(ioaddr + CONFIG_REG_0, DLC_EN); - eth16i_set_port(ioaddr, i); - - if(eth16i_debug > 1) - printk(KERN_DEBUG "Set port number %d\n", i); - - retcode = eth16i_send_probe_packet(ioaddr, dummy_packet, 64); - if(retcode == 0) { - retcode = eth16i_receive_probe_packet(ioaddr); - if(retcode != -1) { - if(eth16i_debug > 1) - printk(KERN_DEBUG "Eth16i interface port found at %d\n", i); - return i; - } - } - else { - if(eth16i_debug > 1) - printk(KERN_DEBUG "TRANSMIT_DONE timeout when probing interface port\n"); - } - } - - if( eth16i_debug > 1) - printk(KERN_DEBUG "Using default port\n"); - - return E_PORT_BNC; -} - -static void eth16i_set_port(int ioaddr, int porttype) -{ - unsigned short temp = 0; - - eth16i_select_regbank(TRANSCEIVER_MODE_RB, ioaddr); - outb(LOOPBACK_CONTROL, ioaddr + TRANSMIT_MODE_REG); - - temp |= DIS_AUTO_PORT_SEL; - - switch(porttype) { - - case E_PORT_BNC : - temp |= AUI_SELECT; - break; - - case E_PORT_TP : - break; - - case E_PORT_DIX : - temp |= AUI_SELECT; - BITSET(ioaddr + TRANSMIT_MODE_REG, CONTROL_OUTPUT); - break; - } - - outb(temp, ioaddr + TRANSCEIVER_MODE_REG); - - if(eth16i_debug > 1) { - printk(KERN_DEBUG "TRANSMIT_MODE_REG = %x\n", inb(ioaddr + TRANSMIT_MODE_REG)); - printk(KERN_DEBUG "TRANSCEIVER_MODE_REG = %x\n", - inb(ioaddr+TRANSCEIVER_MODE_REG)); - } -} - -static int eth16i_send_probe_packet(int ioaddr, unsigned char *b, int l) -{ - unsigned long starttime; - - outb(0xff, ioaddr + TX_STATUS_REG); - - outw(l, ioaddr + DATAPORT); - outsw(ioaddr + DATAPORT, (unsigned short *)b, (l + 1) >> 1); - - starttime = jiffies; - outb(TX_START | 1, ioaddr + TRANSMIT_START_REG); - - while( (inb(ioaddr + TX_STATUS_REG) & 0x80) == 0) { - if( time_after(jiffies, starttime + TX_TIMEOUT)) { - return -1; - } - } - - return 0; -} - -static int eth16i_receive_probe_packet(int ioaddr) -{ - unsigned long starttime; - - starttime = jiffies; - - while((inb(ioaddr + TX_STATUS_REG) & 0x20) == 0) { - if( time_after(jiffies, starttime + TX_TIMEOUT)) { - - if(eth16i_debug > 1) - printk(KERN_DEBUG "Timeout occurred waiting transmit packet received\n"); - starttime = jiffies; - while((inb(ioaddr + RX_STATUS_REG) & 0x80) == 0) { - if( time_after(jiffies, starttime + TX_TIMEOUT)) { - if(eth16i_debug > 1) - printk(KERN_DEBUG "Timeout occurred waiting receive packet\n"); - return -1; - } - } - - if(eth16i_debug > 1) - printk(KERN_DEBUG "RECEIVE_PACKET\n"); - return 0; /* Found receive packet */ - } - } - - if(eth16i_debug > 1) { - printk(KERN_DEBUG "TRANSMIT_PACKET_RECEIVED %x\n", inb(ioaddr + TX_STATUS_REG)); - printk(KERN_DEBUG "RX_STATUS_REG = %x\n", inb(ioaddr + RX_STATUS_REG)); - } - - return 0; /* Return success */ -} - -#if 0 -static int eth16i_set_irq(struct net_device* dev) -{ - const int ioaddr = dev->base_addr; - const int irq = dev->irq; - int i = 0; - - if(ioaddr < 0x1000) { - while(eth16i_irqmap[i] && eth16i_irqmap[i] != irq) - i++; - - if(i < NUM_OF_ISA_IRQS) { - u8 cbyte = inb(ioaddr + JUMPERLESS_CONFIG); - cbyte = (cbyte & 0x3F) | (i << 6); - outb(cbyte, ioaddr + JUMPERLESS_CONFIG); - return 0; - } - } - else { - printk(KERN_NOTICE "%s: EISA Interrupt cannot be set. Use EISA Configuration utility.\n", dev->name); - } - - return -1; - -} -#endif - -static int __init eth16i_get_irq(int ioaddr) -{ - unsigned char cbyte; - - if( ioaddr < 0x1000) { - cbyte = inb(ioaddr + JUMPERLESS_CONFIG); - return eth16i_irqmap[((cbyte & 0xC0) >> 6)]; - } else { /* Oh..the card is EISA so method getting IRQ different */ - unsigned short index = 0; - cbyte = inb(ioaddr + EISA_IRQ_REG); - while( (cbyte & 0x01) == 0) { - cbyte = cbyte >> 1; - index++; - } - return eth32i_irqmap[index]; - } -} - -static int __init eth16i_check_signature(int ioaddr) -{ - int i; - unsigned char creg[4] = { 0 }; - - for(i = 0; i < 4 ; i++) { - - creg[i] = inb(ioaddr + TRANSMIT_MODE_REG + i); - - if(eth16i_debug > 1) - printk("eth16i: read signature byte %x at %x\n", - creg[i], - ioaddr + TRANSMIT_MODE_REG + i); - } - - creg[0] &= 0x0F; /* Mask collision cnr */ - creg[2] &= 0x7F; /* Mask DCLEN bit */ - -#if 0 - /* - This was removed because the card was sometimes left to state - from which it couldn't be find anymore. If there is need - to more strict check still this have to be fixed. - */ - if( ! ((creg[0] == 0x06) && (creg[1] == 0x41)) ) { - if(creg[1] != 0x42) - return -1; - } -#endif - - if( !((creg[2] == 0x36) && (creg[3] == 0xE0)) ) { - creg[2] &= 0x40; - creg[3] &= 0x03; - - if( !((creg[2] == 0x40) && (creg[3] == 0x00)) ) - return -1; - } - - if(eth16i_read_eeprom(ioaddr, E_NODEID_0) != 0) - return -1; - - if((eth16i_read_eeprom(ioaddr, E_NODEID_1) & 0xFF00) != 0x4B00) - return -1; - - return 0; -} - -static int eth16i_read_eeprom(int ioaddr, int offset) -{ - int data = 0; - - eth16i_eeprom_cmd(ioaddr, EEPROM_READ | offset); - outb(CS_1, ioaddr + EEPROM_CTRL_REG); - data = eth16i_read_eeprom_word(ioaddr); - outb(CS_0 | SK_0, ioaddr + EEPROM_CTRL_REG); - - return data; -} - -static int eth16i_read_eeprom_word(int ioaddr) -{ - int i; - int data = 0; - - for(i = 16; i > 0; i--) { - outb(CS_1 | SK_0, ioaddr + EEPROM_CTRL_REG); - eeprom_slow_io(); - outb(CS_1 | SK_1, ioaddr + EEPROM_CTRL_REG); - eeprom_slow_io(); - data = (data << 1) | - ((inb(ioaddr + EEPROM_DATA_REG) & DI_1) ? 1 : 0); - - eeprom_slow_io(); - } - - return data; -} - -static void eth16i_eeprom_cmd(int ioaddr, unsigned char command) -{ - int i; - - outb(CS_0 | SK_0, ioaddr + EEPROM_CTRL_REG); - outb(DI_0, ioaddr + EEPROM_DATA_REG); - outb(CS_1 | SK_0, ioaddr + EEPROM_CTRL_REG); - outb(DI_1, ioaddr + EEPROM_DATA_REG); - outb(CS_1 | SK_1, ioaddr + EEPROM_CTRL_REG); - - for(i = 7; i >= 0; i--) { - short cmd = ( (command & (1 << i)) ? DI_1 : DI_0 ); - outb(cmd, ioaddr + EEPROM_DATA_REG); - outb(CS_1 | SK_0, ioaddr + EEPROM_CTRL_REG); - eeprom_slow_io(); - outb(CS_1 | SK_1, ioaddr + EEPROM_CTRL_REG); - eeprom_slow_io(); - } -} - -static int eth16i_open(struct net_device *dev) -{ - struct eth16i_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - /* Powerup the chip */ - outb(0xc0 | POWERUP, ioaddr + CONFIG_REG_1); - - /* Initialize the chip */ - eth16i_initialize(dev, 0); - - /* Set the transmit buffer size */ - lp->tx_buf_size = eth16i_tx_buf_map[ETH16I_TX_BUF_SIZE & 0x03]; - - if(eth16i_debug > 0) - printk(KERN_DEBUG "%s: transmit buffer size %d\n", - dev->name, lp->tx_buf_size); - - /* Now enable Transmitter and Receiver sections */ - BITCLR(ioaddr + CONFIG_REG_0, DLC_EN); - - /* Now switch to register bank 2, for run time operation */ - eth16i_select_regbank(2, ioaddr); - - lp->open_time = jiffies; - lp->tx_started = 0; - lp->tx_queue = 0; - lp->tx_queue_len = 0; - - /* Turn on interrupts*/ - outw(ETH16I_INTR_ON, ioaddr + TX_INTR_REG); - - netif_start_queue(dev); - return 0; -} - -static int eth16i_close(struct net_device *dev) -{ - struct eth16i_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - eth16i_reset(dev); - - /* Turn off interrupts*/ - outw(ETH16I_INTR_OFF, ioaddr + TX_INTR_REG); - - netif_stop_queue(dev); - - lp->open_time = 0; - - /* Disable transmit and receive */ - BITSET(ioaddr + CONFIG_REG_0, DLC_EN); - - /* Reset the chip */ - /* outb(0xff, ioaddr + RESET); */ - /* outw(0xffff, ioaddr + TX_STATUS_REG); */ - - outb(0x00, ioaddr + CONFIG_REG_1); - - return 0; -} - -static void eth16i_timeout(struct net_device *dev) -{ - struct eth16i_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - /* - If we get here, some higher level has decided that - we are broken. There should really be a "kick me" - function call instead. - */ - - outw(ETH16I_INTR_OFF, ioaddr + TX_INTR_REG); - printk(KERN_WARNING "%s: transmit timed out with status %04x, %s ?\n", - dev->name, - inw(ioaddr + TX_STATUS_REG), (inb(ioaddr + TX_STATUS_REG) & TX_DONE) ? - "IRQ conflict" : "network cable problem"); - - dev->trans_start = jiffies; /* prevent tx timeout */ - - /* Let's dump all registers */ - if(eth16i_debug > 0) { - printk(KERN_DEBUG "%s: timeout: %02x %02x %02x %02x %02x %02x %02x %02x.\n", - dev->name, inb(ioaddr + 0), - inb(ioaddr + 1), inb(ioaddr + 2), - inb(ioaddr + 3), inb(ioaddr + 4), - inb(ioaddr + 5), - inb(ioaddr + 6), inb(ioaddr + 7)); - - printk(KERN_DEBUG "%s: transmit start reg: %02x. collision reg %02x\n", - dev->name, inb(ioaddr + TRANSMIT_START_REG), - inb(ioaddr + COL_16_REG)); - printk(KERN_DEBUG "lp->tx_queue = %d\n", lp->tx_queue); - printk(KERN_DEBUG "lp->tx_queue_len = %d\n", lp->tx_queue_len); - printk(KERN_DEBUG "lp->tx_started = %d\n", lp->tx_started); - } - dev->stats.tx_errors++; - eth16i_reset(dev); - dev->trans_start = jiffies; /* prevent tx timeout */ - outw(ETH16I_INTR_ON, ioaddr + TX_INTR_REG); - netif_wake_queue(dev); -} - -static netdev_tx_t eth16i_tx(struct sk_buff *skb, struct net_device *dev) -{ - struct eth16i_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - int status = 0; - ushort length = skb->len; - unsigned char *buf; - unsigned long flags; - - if (length < ETH_ZLEN) { - if (skb_padto(skb, ETH_ZLEN)) - return NETDEV_TX_OK; - length = ETH_ZLEN; - } - buf = skb->data; - - netif_stop_queue(dev); - - /* Turn off TX interrupts */ - outw(ETH16I_INTR_OFF, ioaddr + TX_INTR_REG); - - /* We would be better doing the disable_irq tricks the 3c509 does, - that would make this suck a lot less */ - - spin_lock_irqsave(&lp->lock, flags); - - if( (length + 2) > (lp->tx_buf_size - lp->tx_queue_len)) { - if(eth16i_debug > 0) - printk(KERN_WARNING "%s: Transmit buffer full.\n", dev->name); - } - else { - outw(length, ioaddr + DATAPORT); - - if( ioaddr < 0x1000 ) - outsw(ioaddr + DATAPORT, buf, (length + 1) >> 1); - else { - unsigned char frag = length % 4; - outsl(ioaddr + DATAPORT, buf, length >> 2); - if( frag != 0 ) { - outsw(ioaddr + DATAPORT, (buf + (length & 0xFFFC)), 1); - if( frag == 3 ) - outsw(ioaddr + DATAPORT, - (buf + (length & 0xFFFC) + 2), 1); - } - } - lp->tx_buffered_packets++; - lp->tx_buffered_bytes = length; - lp->tx_queue++; - lp->tx_queue_len += length + 2; - } - lp->tx_buf_busy = 0; - - if(lp->tx_started == 0) { - /* If the transmitter is idle..always trigger a transmit */ - outb(TX_START | lp->tx_queue, ioaddr + TRANSMIT_START_REG); - lp->tx_queue = 0; - lp->tx_queue_len = 0; - lp->tx_started = 1; - netif_wake_queue(dev); - } - else if(lp->tx_queue_len < lp->tx_buf_size - (ETH_FRAME_LEN + 2)) { - /* There is still more room for one more packet in tx buffer */ - netif_wake_queue(dev); - } - - spin_unlock_irqrestore(&lp->lock, flags); - - outw(ETH16I_INTR_ON, ioaddr + TX_INTR_REG); - /* Turn TX interrupts back on */ - /* outb(TX_INTR_DONE | TX_INTR_16_COL, ioaddr + TX_INTR_REG); */ - status = 0; - dev_kfree_skb(skb); - return NETDEV_TX_OK; -} - -static void eth16i_rx(struct net_device *dev) -{ - int ioaddr = dev->base_addr; - int boguscount = MAX_RX_LOOP; - - /* Loop until all packets have been read */ - while( (inb(ioaddr + RECEIVE_MODE_REG) & RX_BUFFER_EMPTY) == 0) { - - /* Read status byte from receive buffer */ - ushort status = inw(ioaddr + DATAPORT); - - /* Get the size of the packet from receive buffer */ - ushort pkt_len = inw(ioaddr + DATAPORT); - - if(eth16i_debug > 4) - printk(KERN_DEBUG "%s: Receiving packet mode %02x status %04x.\n", - dev->name, - inb(ioaddr + RECEIVE_MODE_REG), status); - - if( !(status & PKT_GOOD) ) { - dev->stats.rx_errors++; - - if( (pkt_len < ETH_ZLEN) || (pkt_len > ETH_FRAME_LEN) ) { - dev->stats.rx_length_errors++; - eth16i_reset(dev); - return; - } - else { - eth16i_skip_packet(dev); - dev->stats.rx_dropped++; - } - } - else { /* Ok so now we should have a good packet */ - struct sk_buff *skb; - - skb = netdev_alloc_skb(dev, pkt_len + 3); - if( skb == NULL ) { - printk(KERN_WARNING "%s: Could'n allocate memory for packet (len %d)\n", - dev->name, pkt_len); - eth16i_skip_packet(dev); - dev->stats.rx_dropped++; - break; - } - - skb_reserve(skb,2); - - /* - Now let's get the packet out of buffer. - size is (pkt_len + 1) >> 1, cause we are now reading words - and it have to be even aligned. - */ - - if(ioaddr < 0x1000) - insw(ioaddr + DATAPORT, skb_put(skb, pkt_len), - (pkt_len + 1) >> 1); - else { - unsigned char *buf = skb_put(skb, pkt_len); - unsigned char frag = pkt_len % 4; - - insl(ioaddr + DATAPORT, buf, pkt_len >> 2); - - if(frag != 0) { - unsigned short rest[2]; - rest[0] = inw( ioaddr + DATAPORT ); - if(frag == 3) - rest[1] = inw( ioaddr + DATAPORT ); - - memcpy(buf + (pkt_len & 0xfffc), (char *)rest, frag); - } - } - - skb->protocol=eth_type_trans(skb, dev); - - if( eth16i_debug > 5 ) { - int i; - printk(KERN_DEBUG "%s: Received packet of length %d.\n", - dev->name, pkt_len); - for(i = 0; i < 14; i++) - printk(KERN_DEBUG " %02x", skb->data[i]); - printk(KERN_DEBUG ".\n"); - } - netif_rx(skb); - dev->stats.rx_packets++; - dev->stats.rx_bytes += pkt_len; - - } /* else */ - - if(--boguscount <= 0) - break; - - } /* while */ -} - -static irqreturn_t eth16i_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - struct eth16i_local *lp; - int ioaddr = 0, status; - int handled = 0; - - ioaddr = dev->base_addr; - lp = netdev_priv(dev); - - /* Turn off all interrupts from adapter */ - outw(ETH16I_INTR_OFF, ioaddr + TX_INTR_REG); - - /* eth16i_tx won't be called */ - spin_lock(&lp->lock); - - status = inw(ioaddr + TX_STATUS_REG); /* Get the status */ - outw(status, ioaddr + TX_STATUS_REG); /* Clear status bits */ - - if (status) - handled = 1; - - if(eth16i_debug > 3) - printk(KERN_DEBUG "%s: Interrupt with status %04x.\n", dev->name, status); - - if( status & 0x7f00 ) { - - dev->stats.rx_errors++; - - if(status & (BUS_RD_ERR << 8) ) - printk(KERN_WARNING "%s: Bus read error.\n",dev->name); - if(status & (SHORT_PKT_ERR << 8) ) dev->stats.rx_length_errors++; - if(status & (ALIGN_ERR << 8) ) dev->stats.rx_frame_errors++; - if(status & (CRC_ERR << 8) ) dev->stats.rx_crc_errors++; - if(status & (RX_BUF_OVERFLOW << 8) ) dev->stats.rx_over_errors++; - } - if( status & 0x001a) { - - dev->stats.tx_errors++; - - if(status & CR_LOST) dev->stats.tx_carrier_errors++; - if(status & TX_JABBER_ERR) dev->stats.tx_window_errors++; - -#if 0 - if(status & COLLISION) { - dev->stats.collisions += - ((inb(ioaddr+TRANSMIT_MODE_REG) & 0xF0) >> 4); - } -#endif - if(status & COLLISIONS_16) { - if(lp->col_16 < MAX_COL_16) { - lp->col_16++; - dev->stats.collisions++; - /* Resume transmitting, skip failed packet */ - outb(0x02, ioaddr + COL_16_REG); - } - else { - printk(KERN_WARNING "%s: bailing out due to many consecutive 16-in-a-row collisions. Network cable problem?\n", dev->name); - } - } - } - - if( status & 0x00ff ) { /* Let's check the transmit status reg */ - - if(status & TX_DONE) { /* The transmit has been done */ - dev->stats.tx_packets = lp->tx_buffered_packets; - dev->stats.tx_bytes += lp->tx_buffered_bytes; - lp->col_16 = 0; - - if(lp->tx_queue) { /* Is there still packets ? */ - /* There was packet(s) so start transmitting and write also - how many packets there is to be sended */ - outb(TX_START | lp->tx_queue, ioaddr + TRANSMIT_START_REG); - lp->tx_queue = 0; - lp->tx_queue_len = 0; - lp->tx_started = 1; - } - else { - lp->tx_started = 0; - } - netif_wake_queue(dev); - } - } - - if( ( status & 0x8000 ) || - ( (inb(ioaddr + RECEIVE_MODE_REG) & RX_BUFFER_EMPTY) == 0) ) { - eth16i_rx(dev); /* We have packet in receive buffer */ - } - - /* Turn interrupts back on */ - outw(ETH16I_INTR_ON, ioaddr + TX_INTR_REG); - - if(lp->tx_queue_len < lp->tx_buf_size - (ETH_FRAME_LEN + 2)) { - /* There is still more room for one more packet in tx buffer */ - netif_wake_queue(dev); - } - - spin_unlock(&lp->lock); - - return IRQ_RETVAL(handled); -} - -static void eth16i_skip_packet(struct net_device *dev) -{ - int ioaddr = dev->base_addr; - - inw(ioaddr + DATAPORT); - inw(ioaddr + DATAPORT); - inw(ioaddr + DATAPORT); - - outb(SKIP_RX_PACKET, ioaddr + FILTER_SELF_RX_REG); - while( inb( ioaddr + FILTER_SELF_RX_REG ) != 0); -} - -static void eth16i_reset(struct net_device *dev) -{ - struct eth16i_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - if(eth16i_debug > 1) - printk(KERN_DEBUG "%s: Resetting device.\n", dev->name); - - BITSET(ioaddr + CONFIG_REG_0, DLC_EN); - outw(0xffff, ioaddr + TX_STATUS_REG); - eth16i_select_regbank(2, ioaddr); - - lp->tx_started = 0; - lp->tx_buf_busy = 0; - lp->tx_queue = 0; - lp->tx_queue_len = 0; - BITCLR(ioaddr + CONFIG_REG_0, DLC_EN); -} - -static void eth16i_multicast(struct net_device *dev) -{ - int ioaddr = dev->base_addr; - - if (!netdev_mc_empty(dev) || dev->flags&(IFF_ALLMULTI|IFF_PROMISC)) - { - outb(3, ioaddr + RECEIVE_MODE_REG); - } else { - outb(2, ioaddr + RECEIVE_MODE_REG); - } -} - -static void eth16i_select_regbank(unsigned char banknbr, int ioaddr) -{ - unsigned char data; - - data = inb(ioaddr + CONFIG_REG_1); - outb( ((data & 0xF3) | ( (banknbr & 0x03) << 2)), ioaddr + CONFIG_REG_1); -} - -#ifdef MODULE - -static ushort eth16i_parse_mediatype(const char* s) -{ - if(!s) - return E_PORT_FROM_EPROM; - - if (!strncmp(s, "bnc", 3)) - return E_PORT_BNC; - else if (!strncmp(s, "tp", 2)) - return E_PORT_TP; - else if (!strncmp(s, "dix", 3)) - return E_PORT_DIX; - else if (!strncmp(s, "auto", 4)) - return E_PORT_AUTO; - else - return E_PORT_FROM_EPROM; -} - -#define MAX_ETH16I_CARDS 4 /* Max number of Eth16i cards per module */ - -static struct net_device *dev_eth16i[MAX_ETH16I_CARDS]; -static int io[MAX_ETH16I_CARDS]; -#if 0 -static int irq[MAX_ETH16I_CARDS]; -#endif -static char* mediatype[MAX_ETH16I_CARDS]; -static int debug = -1; - -MODULE_AUTHOR("Mika Kuoppala "); -MODULE_DESCRIPTION("ICL EtherTeam 16i/32 driver"); -MODULE_LICENSE("GPL"); - - -module_param_array(io, int, NULL, 0); -MODULE_PARM_DESC(io, "eth16i I/O base address(es)"); - -#if 0 -module_param_array(irq, int, NULL, 0); -MODULE_PARM_DESC(irq, "eth16i interrupt request number"); -#endif - -module_param_array(mediatype, charp, NULL, 0); -MODULE_PARM_DESC(mediatype, "eth16i media type of interface(s) (bnc,tp,dix,auto,eprom)"); - -module_param(debug, int, 0); -MODULE_PARM_DESC(debug, "eth16i debug level (0-6)"); - -int __init init_module(void) -{ - int this_dev, found = 0; - struct net_device *dev; - - for (this_dev = 0; this_dev < MAX_ETH16I_CARDS; this_dev++) { - dev = alloc_etherdev(sizeof(struct eth16i_local)); - if (!dev) - break; - - dev->base_addr = io[this_dev]; - - if(debug != -1) - eth16i_debug = debug; - - if(eth16i_debug > 1) - printk(KERN_NOTICE "eth16i(%d): interface type %s\n", this_dev, mediatype[this_dev] ? mediatype[this_dev] : "none" ); - - dev->if_port = eth16i_parse_mediatype(mediatype[this_dev]); - - if(io[this_dev] == 0) { - if (this_dev != 0) { /* Only autoprobe 1st one */ - free_netdev(dev); - break; - } - - printk(KERN_NOTICE "eth16i.c: Presently autoprobing (not recommended) for a single card.\n"); - } - - if (do_eth16i_probe(dev) == 0) { - dev_eth16i[found++] = dev; - continue; - } - printk(KERN_WARNING "eth16i.c No Eth16i card found (i/o = 0x%x).\n", - io[this_dev]); - free_netdev(dev); - break; - } - if (found) - return 0; - return -ENXIO; -} - -void __exit cleanup_module(void) -{ - int this_dev; - - for(this_dev = 0; this_dev < MAX_ETH16I_CARDS; this_dev++) { - struct net_device *dev = dev_eth16i[this_dev]; - - if (netdev_priv(dev)) { - unregister_netdev(dev); - free_irq(dev->irq, dev); - release_region(dev->base_addr, ETH16I_IO_EXTENT); - free_netdev(dev); - } - } -} -#endif /* MODULE */ -- cgit v1.2.3 From dca9ab9274ab1b01fa2a78d5b82e9d1ea8c22b39 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Fri, 15 Feb 2013 23:55:05 +0000 Subject: MAINTAINERS: Jiri Pirko email change Change email for team driver maintainership. Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller --- MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'MAINTAINERS') diff --git a/MAINTAINERS b/MAINTAINERS index 35a56bcd5e75..b61e9b13af0a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7536,7 +7536,7 @@ S: Maintained F: drivers/media/tuners/tea5767.* TEAM DRIVER -M: Jiri Pirko +M: Jiri Pirko L: netdev@vger.kernel.org S: Supported F: drivers/net/team/ -- cgit v1.2.3