From 070276d5d049f385763dee19112bea08f56c9a0d Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sun, 17 May 2009 22:32:23 +0100 Subject: [ARM] S3C24XX: GPIO: Change to macros for GPIO numbering Prepare to remove the large number of S3C2410_GPxn defines by moving to S3C2410_GPx(n) in arch/arm. The following perl was used to change the files: perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g' Signed-off-by: Ben Dooks --- arch/arm/mach-s3c2410/h1940-bluetooth.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) (limited to 'arch/arm/mach-s3c2410/h1940-bluetooth.c') diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c index 9bbea8a73ddc..5aabf117cbb0 100644 --- a/arch/arm/mach-s3c2410/h1940-bluetooth.c +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c @@ -43,9 +43,9 @@ static void h1940bt_enable(int on) h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER); /* Reset the chip */ mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 1); + s3c2410_gpio_setpin(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 0); + s3c2410_gpio_setpin(S3C2410_GPH(1), 0); state = 1; } @@ -54,9 +54,9 @@ static void h1940bt_enable(int on) led_trigger_event(bt_led_trigger, 0); #endif - s3c2410_gpio_setpin(S3C2410_GPH1, 1); + s3c2410_gpio_setpin(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 0); + s3c2410_gpio_setpin(S3C2410_GPH(1), 0); mdelay(10); h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0); @@ -89,14 +89,14 @@ static DEVICE_ATTR(enable, 0644, static int __init h1940bt_probe(struct platform_device *pdev) { /* Configures BT serial port GPIOs */ - s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0); - s3c2410_gpio_pullup(S3C2410_GPH0, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_pullup(S3C2410_GPH1, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0); - s3c2410_gpio_pullup(S3C2410_GPH2, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0); - s3c2410_gpio_pullup(S3C2410_GPH3, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0); + s3c2410_gpio_pullup(S3C2410_GPH(0), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_pullup(S3C2410_GPH(1), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0); + s3c2410_gpio_pullup(S3C2410_GPH(2), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0); + s3c2410_gpio_pullup(S3C2410_GPH(3), 1); #ifdef CONFIG_LEDS_H1940 led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger); -- cgit v1.2.3