From 934de3415e5e63561530d1c571dc47e116a9c63a Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 16 Sep 2019 14:50:21 +0200 Subject: arm64: dts: meson-g12a: Add PCIe node This adds the Amlogic G12A PCI Express controller node, also using the USB3+PCIe Combo PHY. The PHY mode selection is static, thus the USB3+PCIe Combo PHY phandle would need to be removed from the USB control node if the shared differential lines are used for PCIe instead of USB3. Signed-off-by: Neil Armstrong Signed-off-by: Lorenzo Pieralisi Reviewed-by: Andrew Murray --- arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 33 +++++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-sm1.dtsi | 4 +++ 2 files changed, 37 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi index 3f39e020f74e..7ab71172cd3c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi @@ -95,6 +95,39 @@ #size-cells = <2>; ranges; + pcie: pcie@fc000000 { + compatible = "amlogic,g12a-pcie", "snps,dw-pcie"; + reg = <0x0 0xfc000000 0x0 0x400000 + 0x0 0xff648000 0x0 0x2000 + 0x0 0xfc400000 0x0 0x200000>; + reg-names = "elbi", "cfg", "config"; + interrupts = ; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; + bus-range = <0x0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000 + 0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>; + + clocks = <&clkc CLKID_PCIE_PHY + &clkc CLKID_PCIE_COMB + &clkc CLKID_PCIE_PLL>; + clock-names = "general", + "pclk", + "port"; + resets = <&reset RESET_PCIE_CTRL_A>, + <&reset RESET_PCIE_APB>; + reset-names = "port", + "apb"; + num-lanes = <1>; + phys = <&usb3_pcie_phy PHY_TYPE_PCIE>; + phy-names = "pcie"; + status = "disabled"; + }; + ethmac: ethernet@ff3f0000 { compatible = "amlogic,meson-axg-dwmac", "snps,dwmac-3.70a", diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi index 521573f3a5ba..256ea0349ffc 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi @@ -134,6 +134,10 @@ power-domains = <&pwrc PWRC_SM1_ETH_ID>; }; +&pcie { + power-domains = <&pwrc PWRC_SM1_PCIE_ID>; +}; + &pwrc { compatible = "amlogic,meson-sm1-pwrc"; }; -- cgit v1.2.3 From ba1f8af7f772139607d46da3fc151a403f966f46 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 16 Sep 2019 14:50:22 +0200 Subject: arm64: dts: khadas-vim3: add commented support for PCIe The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between an USB3.0 Type A connector and a M.2 Key M slot. The PHY driving these differential lines is shared between the USB3.0 controller and the PCIe Controller, thus only a single controller can use it. The needed DT configuration when the MCU is configured to mux the PCIe/USB3.0 differential lines to the M.2 Key M slot is added commented and may be uncommented to disable USB3.0 from the USB Complex and enable the PCIe controller. The End User is not expected to uncomment the following except for testing purposes, but instead rely on the firmware/bootloader to update these nodes accordingly if PCIe mode is selected by the MCU. Signed-off-by: Neil Armstrong Signed-off-by: Lorenzo Pieralisi Reviewed-by: Andrew Murray --- .../dts/amlogic/meson-g12b-a311d-khadas-vim3.dts | 25 ++++++++++++++++++++++ .../dts/amlogic/meson-g12b-s922x-khadas-vim3.dts | 25 ++++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi | 4 ++++ .../boot/dts/amlogic/meson-sm1-khadas-vim3l.dts | 25 ++++++++++++++++++++++ 4 files changed, 79 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts index 3a6a1e0c1e32..124a80901084 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts @@ -14,3 +14,28 @@ / { compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b"; }; + +/* + * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential + * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between + * an USB3.0 Type A connector and a M.2 Key M slot. + * The PHY driving these differential lines is shared between + * the USB3.0 controller and the PCIe Controller, thus only + * a single controller can use it. + * If the MCU is configured to mux the PCIe/USB3.0 differential lines + * to the M.2 Key M slot, uncomment the following block to disable + * USB3.0 from the USB Complex and enable the PCIe controller. + * The End User is not expected to uncomment the following except for + * testing purposes, but instead rely on the firmware/bootloader to + * update these nodes accordingly if PCIe mode is selected by the MCU. + */ +/* +&pcie { + status = "okay"; +}; + +&usb { + phys = <&usb2_phy0>, <&usb2_phy1>; + phy-names = "usb2-phy0", "usb2-phy1"; +}; + */ diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts index b73deb282120..bba98f982ad6 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts @@ -14,3 +14,28 @@ / { compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b"; }; + +/* + * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential + * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between + * an USB3.0 Type A connector and a M.2 Key M slot. + * The PHY driving these differential lines is shared between + * the USB3.0 controller and the PCIe Controller, thus only + * a single controller can use it. + * If the MCU is configured to mux the PCIe/USB3.0 differential lines + * to the M.2 Key M slot, uncomment the following block to disable + * USB3.0 from the USB Complex and enable the PCIe controller. + * The End User is not expected to uncomment the following except for + * testing purposes, but instead rely on the firmware/bootloader to + * update these nodes accordingly if PCIe mode is selected by the MCU. + */ +/* +&pcie { + status = "okay"; +}; + +&usb { + phys = <&usb2_phy0>, <&usb2_phy1>; + phy-names = "usb2-phy0", "usb2-phy1"; +}; + */ diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi index 8647da7d6609..eac5720dc15f 100644 --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi @@ -246,6 +246,10 @@ linux,rc-map-name = "rc-khadas"; }; +&pcie { + reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>; +}; + &pwm_ef { status = "okay"; pinctrl-0 = <&pwm_e_pins>; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts index 5233bd7cacfb..dbbf29a0dbf6 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts @@ -68,3 +68,28 @@ clock-names = "clkin1"; status = "okay"; }; + +/* + * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential + * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between + * an USB3.0 Type A connector and a M.2 Key M slot. + * The PHY driving these differential lines is shared between + * the USB3.0 controller and the PCIe Controller, thus only + * a single controller can use it. + * If the MCU is configured to mux the PCIe/USB3.0 differential lines + * to the M.2 Key M slot, uncomment the following block to disable + * USB3.0 from the USB Complex and enable the PCIe controller. + * The End User is not expected to uncomment the following except for + * testing purposes, but instead rely on the firmware/bootloader to + * update these nodes accordingly if PCIe mode is selected by the MCU. + */ +/* +&pcie { + status = "okay"; +}; + +&usb { + phys = <&usb2_phy0>, <&usb2_phy1>; + phy-names = "usb2-phy0", "usb2-phy1"; +}; + */ -- cgit v1.2.3 From a1b39bae16a62ce4aae02d958224f19316d98b24 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Fri, 25 Oct 2019 08:10:37 +0200 Subject: asm-generic: Make msi.h a mandatory include/asm header msi.h is generic for all architectures except x86, which has its own version. Enabling MSI by adding msi.h to every architecture's Kbuild is just an additional step which doesn't need to be done. Make msi.h mandatory in the asm-generic/Kbuild so we don't have to do it for each architecture. Suggested-by: Christoph Hellwig Link: https://lore.kernel.org/r/c991669e29a79b1a8e28c3b4b3a125801a693de8.1571983829.git.michal.simek@xilinx.com Tested-by: Paul Walmsley # build only, rv32/rv64 Signed-off-by: Michal Simek Signed-off-by: Bjorn Helgaas Reviewed-by: Masahiro Yamada Acked-by: Waiman Long Acked-by: Paul Walmsley # arch/riscv --- arch/arc/include/asm/Kbuild | 1 - arch/arm/include/asm/Kbuild | 1 - arch/arm64/include/asm/Kbuild | 1 - arch/mips/include/asm/Kbuild | 1 - arch/powerpc/include/asm/Kbuild | 1 - arch/riscv/include/asm/Kbuild | 1 - arch/sparc/include/asm/Kbuild | 1 - include/asm-generic/Kbuild | 1 + 8 files changed, 1 insertion(+), 7 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arc/include/asm/Kbuild b/arch/arc/include/asm/Kbuild index 393d4f5e1450..1b505694691e 100644 --- a/arch/arc/include/asm/Kbuild +++ b/arch/arc/include/asm/Kbuild @@ -17,7 +17,6 @@ generic-y += local64.h generic-y += mcs_spinlock.h generic-y += mm-arch-hooks.h generic-y += mmiowb.h -generic-y += msi.h generic-y += parport.h generic-y += percpu.h generic-y += preempt.h diff --git a/arch/arm/include/asm/Kbuild b/arch/arm/include/asm/Kbuild index 68ca86f85eb7..fa579b23b4df 100644 --- a/arch/arm/include/asm/Kbuild +++ b/arch/arm/include/asm/Kbuild @@ -12,7 +12,6 @@ generic-y += local.h generic-y += local64.h generic-y += mm-arch-hooks.h generic-y += mmiowb.h -generic-y += msi.h generic-y += parport.h generic-y += preempt.h generic-y += seccomp.h diff --git a/arch/arm64/include/asm/Kbuild b/arch/arm64/include/asm/Kbuild index 98a5405c8558..bd23f87d6c55 100644 --- a/arch/arm64/include/asm/Kbuild +++ b/arch/arm64/include/asm/Kbuild @@ -16,7 +16,6 @@ generic-y += local64.h generic-y += mcs_spinlock.h generic-y += mm-arch-hooks.h generic-y += mmiowb.h -generic-y += msi.h generic-y += qrwlock.h generic-y += qspinlock.h generic-y += serial.h diff --git a/arch/mips/include/asm/Kbuild b/arch/mips/include/asm/Kbuild index c8b595c60910..61b0fc2026e6 100644 --- a/arch/mips/include/asm/Kbuild +++ b/arch/mips/include/asm/Kbuild @@ -13,7 +13,6 @@ generic-y += irq_work.h generic-y += local64.h generic-y += mcs_spinlock.h generic-y += mm-arch-hooks.h -generic-y += msi.h generic-y += parport.h generic-y += percpu.h generic-y += preempt.h diff --git a/arch/powerpc/include/asm/Kbuild b/arch/powerpc/include/asm/Kbuild index 64870c7be4a3..17726f2e46de 100644 --- a/arch/powerpc/include/asm/Kbuild +++ b/arch/powerpc/include/asm/Kbuild @@ -10,4 +10,3 @@ generic-y += local64.h generic-y += mcs_spinlock.h generic-y += preempt.h generic-y += vtime.h -generic-y += msi.h diff --git a/arch/riscv/include/asm/Kbuild b/arch/riscv/include/asm/Kbuild index 16970f246860..1efaeddf1e4b 100644 --- a/arch/riscv/include/asm/Kbuild +++ b/arch/riscv/include/asm/Kbuild @@ -22,7 +22,6 @@ generic-y += kvm_para.h generic-y += local.h generic-y += local64.h generic-y += mm-arch-hooks.h -generic-y += msi.h generic-y += percpu.h generic-y += preempt.h generic-y += sections.h diff --git a/arch/sparc/include/asm/Kbuild b/arch/sparc/include/asm/Kbuild index b6212164847b..62de2eb2773d 100644 --- a/arch/sparc/include/asm/Kbuild +++ b/arch/sparc/include/asm/Kbuild @@ -18,7 +18,6 @@ generic-y += mcs_spinlock.h generic-y += mm-arch-hooks.h generic-y += mmiowb.h generic-y += module.h -generic-y += msi.h generic-y += preempt.h generic-y += serial.h generic-y += trace_clock.h diff --git a/include/asm-generic/Kbuild b/include/asm-generic/Kbuild index adff14fcb8e4..ddfee1bd9dc1 100644 --- a/include/asm-generic/Kbuild +++ b/include/asm-generic/Kbuild @@ -4,4 +4,5 @@ # (This file is not included when SRCARCH=um since UML borrows several # asm headers from the host architecutre.) +mandatory-y += msi.h mandatory-y += simd.h -- cgit v1.2.3