From b83e831a3c2d358fea4bf8fa13f387405f2880b6 Mon Sep 17 00:00:00 2001 From: Sylwester Nawrocki Date: Tue, 5 Mar 2013 11:08:47 +0900 Subject: ARM: S5PV210: Fix PL330 DMA controller clkdev entries Since the DMA controller clocks are managed at amba bus level, the PL330 device clocks handling has been removed from the driver in commit 7c71b8eb("DMA: PL330: Remove redundant runtime_suspend/ resume functions") However, this left the S5PV210 platform with only clkdev entries linking "apb_pclk" clock conn_id to a dummy clock, rather than to corresponding platform PL330 DMAC clock. As a result the DMA controller is now attempted to be used on S5PV210 with the clock disabled and the driver fails with an error: dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 ! dma-pl330: probe of dma-pl330.0 failed with error -22 dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 ! dma-pl330: probe of dma-pl330.1 failed with error -22 Fix this by adding "apb_pclk" clkdev entries for the Peripheral DMA controllers 0/1 and removing the dummy apb_pclk clock. Reported-by: Lonsn Tested-by: Lonsn Cc: Inderpal Singh Cc: Boojin Kim Signed-off-by: Sylwester Nawrocki Cc: # v3.7+ Signed-off-by: Kukjin Kim --- arch/arm/mach-s5pv210/clock.c | 36 ++++++++++++++++++------------------ 1 file changed, 18 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c index fcdf52dbcc49..f051f53e35b7 100644 --- a/arch/arm/mach-s5pv210/clock.c +++ b/arch/arm/mach-s5pv210/clock.c @@ -214,11 +214,6 @@ static struct clk clk_pcmcdclk2 = { .name = "pcmcdclk", }; -static struct clk dummy_apb_pclk = { - .name = "apb_pclk", - .id = -1, -}; - static struct clk *clkset_vpllsrc_list[] = { [0] = &clk_fin_vpll, [1] = &clk_sclk_hdmi27m, @@ -305,18 +300,6 @@ static struct clk_ops clk_fout_apll_ops = { static struct clk init_clocks_off[] = { { - .name = "dma", - .devname = "dma-pl330.0", - .parent = &clk_hclk_psys.clk, - .enable = s5pv210_clk_ip0_ctrl, - .ctrlbit = (1 << 3), - }, { - .name = "dma", - .devname = "dma-pl330.1", - .parent = &clk_hclk_psys.clk, - .enable = s5pv210_clk_ip0_ctrl, - .ctrlbit = (1 << 4), - }, { .name = "rot", .parent = &clk_hclk_dsys.clk, .enable = s5pv210_clk_ip0_ctrl, @@ -573,6 +556,20 @@ static struct clk clk_hsmmc3 = { .ctrlbit = (1<<19), }; +static struct clk clk_pdma0 = { + .name = "pdma0", + .parent = &clk_hclk_psys.clk, + .enable = s5pv210_clk_ip0_ctrl, + .ctrlbit = (1 << 3), +}; + +static struct clk clk_pdma1 = { + .name = "pdma1", + .parent = &clk_hclk_psys.clk, + .enable = s5pv210_clk_ip0_ctrl, + .ctrlbit = (1 << 4), +}; + static struct clk *clkset_uart_list[] = { [6] = &clk_mout_mpll.clk, [7] = &clk_mout_epll.clk, @@ -1075,6 +1072,8 @@ static struct clk *clk_cdev[] = { &clk_hsmmc1, &clk_hsmmc2, &clk_hsmmc3, + &clk_pdma0, + &clk_pdma1, }; /* Clock initialisation code */ @@ -1333,6 +1332,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = { CLKDEV_INIT(NULL, "spi_busclk0", &clk_p), CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk), CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk), + CLKDEV_INIT("dma-pl330.0", "apb_pclk", &clk_pdma0), + CLKDEV_INIT("dma-pl330.1", "apb_pclk", &clk_pdma1), }; void __init s5pv210_register_clocks(void) @@ -1361,6 +1362,5 @@ void __init s5pv210_register_clocks(void) for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++) s3c_disable_clocks(clk_cdev[ptr], 1); - s3c24xx_register_clock(&dummy_apb_pclk); s3c_pwmclk_init(); } -- cgit v1.2.3 From 0a96d4d36978c8aeebf5fce1f3041c2d60f23ac0 Mon Sep 17 00:00:00 2001 From: Padmavathi Venna Date: Thu, 7 Mar 2013 10:33:07 +0900 Subject: ARM: EXYNOS: Add #dma-cells for generic dma binding support for PL330 This patch adds #dma-cells property to PL330 DMA controller nodes for supporting generic dma dt bindings on samsung exynos platforms. #dma-channels and #dma-requests are not required now but added in advance. Signed-off-by: Padmavathi Venna Acked-by: Arnd Bergmann Signed-off-by: Kukjin Kim --- arch/arm/boot/dts/exynos4.dtsi | 9 +++++++++ arch/arm/boot/dts/exynos5440.dtsi | 6 ++++++ 2 files changed, 15 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index e1347fceb5bc..1a62bcf18aa3 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -275,18 +275,27 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x12680000 0x1000>; interrupts = <0 35 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; pdma1: pdma@12690000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x12690000 0x1000>; interrupts = <0 36 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; mdma1: mdma@12850000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x12850000 0x1000>; interrupts = <0 34 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <1>; }; }; }; diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi index 5f3562ad6746..9a99755920c0 100644 --- a/arch/arm/boot/dts/exynos5440.dtsi +++ b/arch/arm/boot/dts/exynos5440.dtsi @@ -142,12 +142,18 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x120000 0x1000>; interrupts = <0 34 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; pdma1: pdma@121B0000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x121000 0x1000>; interrupts = <0 35 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; }; -- cgit v1.2.3 From 44e9ac45754a182e8121bf137368452365d4cc4b Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Wed, 13 Feb 2013 09:45:50 +0000 Subject: ARM: shmobile: marzen: Include mmc/host.h mmc/host.h provides MMC_CAP_SD_HIGHSPEED which is used in board-marzen.c This resolves a build problem observed when compiling with "mmc: tmio: remove unused and deprecated symbols" applied. Acked-by: Guennadi Liakhovetski Signed-off-by: Simon Horman --- arch/arm/mach-shmobile/board-marzen.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-shmobile/board-marzen.c b/arch/arm/mach-shmobile/board-marzen.c index cdcb799e802f..fec49ebc359a 100644 --- a/arch/arm/mach-shmobile/board-marzen.c +++ b/arch/arm/mach-shmobile/board-marzen.c @@ -32,6 +32,7 @@ #include #include #include +#include #include #include #include -- cgit v1.2.3 From 069552777a121eb39da29de4bc0383483dbe1f7e Mon Sep 17 00:00:00 2001 From: Matt Porter Date: Tue, 5 Mar 2013 10:58:22 -0500 Subject: ARM: davinci: edma: fix dmaengine induced null pointer dereference on da830 This adds additional error checking to the private edma api implementation to catch the case where the edma_alloc_slot() has an invalid controller parameter. The edma dmaengine wrapper driver relies on this condition being handled in order to avoid setting up a second edma dmaengine instance on DA830. Verfied using a DA850 with the second EDMA controller platform instance removed to simulate a DA830 which only has a single EDMA controller. Reported-by: Tomas Novotny Signed-off-by: Matt Porter Cc: stable@vger.kernel.org # v3.7.x+ Tested-by: Tomas Novotny Signed-off-by: Sekhar Nori --- arch/arm/mach-davinci/dma.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-davinci/dma.c b/arch/arm/mach-davinci/dma.c index a685e9706b7b..45b7c71d9cc1 100644 --- a/arch/arm/mach-davinci/dma.c +++ b/arch/arm/mach-davinci/dma.c @@ -743,6 +743,9 @@ EXPORT_SYMBOL(edma_free_channel); */ int edma_alloc_slot(unsigned ctlr, int slot) { + if (!edma_cc[ctlr]) + return -EINVAL; + if (slot >= 0) slot = EDMA_CHAN_SLOT(slot); -- cgit v1.2.3 From f04feec2501774fe20fc7c77b5a16b9e23b36f95 Mon Sep 17 00:00:00 2001 From: Richard Genoud Date: Mon, 11 Mar 2013 15:12:39 +0100 Subject: ARM: at91: dt: at91sam9x5: correct NAND pins comments Comments on NAND pins where inverted. Signed-off-by: Richard Genoud Acked-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91sam9x5.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index aa98e641931f..9b5d0480d7ee 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -238,8 +238,8 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */ - 3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + <3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1>; /* PD5 gpio RDY/BUSY pin pull_up */ }; }; -- cgit v1.2.3 From 7f06472f1c3281abceea36059f94e099bfe4698f Mon Sep 17 00:00:00 2001 From: Richard Genoud Date: Mon, 11 Mar 2013 15:12:40 +0100 Subject: ARM: at91: dt: at91sam9x5: complete NAND pinctrl There was only chip enable and readdy/busy pins for the nand controller. This add the rest of the pins. pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs. Signed-off-by: Richard Genoud Acked-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91sam9x5.dtsi | 28 ++++++++++++++++++++++++++-- 1 file changed, 26 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 9b5d0480d7ee..a98c0d50fbbe 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -238,8 +238,32 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ - 3 5 0x0 0x1>; /* PD5 gpio RDY/BUSY pin pull_up */ + <3 0 0x1 0x0 /* PD0 periph A Read Enable */ + 3 1 0x1 0x0 /* PD1 periph A Write Enable */ + 3 2 0x1 0x0 /* PD2 periph A Address Latch Enable */ + 3 3 0x1 0x0 /* PD3 periph A Command Latch Enable */ + 3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1 /* PD5 gpio RDY/BUSY pin pull_up */ + 3 6 0x1 0x0 /* PD6 periph A Data bit 0 */ + 3 7 0x1 0x0 /* PD7 periph A Data bit 1 */ + 3 8 0x1 0x0 /* PD8 periph A Data bit 2 */ + 3 9 0x1 0x0 /* PD9 periph A Data bit 3 */ + 3 10 0x1 0x0 /* PD10 periph A Data bit 4 */ + 3 11 0x1 0x0 /* PD11 periph A Data bit 5 */ + 3 12 0x1 0x0 /* PD12 periph A Data bit 6 */ + 3 13 0x1 0x0>; /* PD13 periph A Data bit 7 */ + }; + + pinctrl_nand_16bits: nand_16bits-0 { + atmel,pins = + <3 14 0x1 0x0 /* PD14 periph A Data bit 8 */ + 3 15 0x1 0x0 /* PD15 periph A Data bit 9 */ + 3 16 0x1 0x0 /* PD16 periph A Data bit 10 */ + 3 17 0x1 0x0 /* PD17 periph A Data bit 11 */ + 3 18 0x1 0x0 /* PD18 periph A Data bit 12 */ + 3 19 0x1 0x0 /* PD19 periph A Data bit 13 */ + 3 20 0x1 0x0 /* PD20 periph A Data bit 14 */ + 3 21 0x1 0x0>; /* PD21 periph A Data bit 15 */ }; }; -- cgit v1.2.3 From 647f8d94a4e69d39e88a617846755655853c20f5 Mon Sep 17 00:00:00 2001 From: Ludovic Desroches Date: Fri, 8 Mar 2013 16:18:21 +0100 Subject: ARM: at91: add gpio suspend/resume support when using pinctrl gpio suspend/resume and wakeup sources where not managed when using pinctrl so it was impossible to wake up the system with a gpio. Signed-off-by: Ludovic Desroches Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Linus Walleij Signed-off-by: Nicolas Ferre --- arch/arm/mach-at91/include/mach/gpio.h | 8 +++++ arch/arm/mach-at91/pm.c | 10 ++++-- drivers/pinctrl/pinctrl-at91.c | 61 +++++++++++++++++++++++++++++++++- 3 files changed, 76 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h index eed465ab0dd7..5fc23771c154 100644 --- a/arch/arm/mach-at91/include/mach/gpio.h +++ b/arch/arm/mach-at91/include/mach/gpio.h @@ -209,6 +209,14 @@ extern int at91_get_gpio_value(unsigned pin); extern void at91_gpio_suspend(void); extern void at91_gpio_resume(void); +#ifdef CONFIG_PINCTRL_AT91 +extern void at91_pinctrl_gpio_suspend(void); +extern void at91_pinctrl_gpio_resume(void); +#else +static inline void at91_pinctrl_gpio_suspend(void) {} +static inline void at91_pinctrl_gpio_resume(void) {} +#endif + #endif /* __ASSEMBLY__ */ #endif diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index adb6db888a1f..73f1f250403a 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -201,7 +201,10 @@ extern u32 at91_slow_clock_sz; static int at91_pm_enter(suspend_state_t state) { - at91_gpio_suspend(); + if (of_have_populated_dt()) + at91_pinctrl_gpio_suspend(); + else + at91_gpio_suspend(); at91_irq_suspend(); pr_debug("AT91: PM - wake mask %08x, pm state %d\n", @@ -286,7 +289,10 @@ static int at91_pm_enter(suspend_state_t state) error: target_state = PM_SUSPEND_ON; at91_irq_resume(); - at91_gpio_resume(); + if (of_have_populated_dt()) + at91_pinctrl_gpio_resume(); + else + at91_gpio_resume(); return 0; } diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c index 75933a6aa828..efb7f10e902a 100644 --- a/drivers/pinctrl/pinctrl-at91.c +++ b/drivers/pinctrl/pinctrl-at91.c @@ -1277,21 +1277,80 @@ static int alt_gpio_irq_type(struct irq_data *d, unsigned type) } #ifdef CONFIG_PM + +static u32 wakeups[MAX_GPIO_BANKS]; +static u32 backups[MAX_GPIO_BANKS]; + static int gpio_irq_set_wake(struct irq_data *d, unsigned state) { struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d); unsigned bank = at91_gpio->pioc_idx; + unsigned mask = 1 << d->hwirq; if (unlikely(bank >= MAX_GPIO_BANKS)) return -EINVAL; + if (state) + wakeups[bank] |= mask; + else + wakeups[bank] &= ~mask; + irq_set_irq_wake(at91_gpio->pioc_virq, state); return 0; } + +void at91_pinctrl_gpio_suspend(void) +{ + int i; + + for (i = 0; i < gpio_banks; i++) { + void __iomem *pio; + + if (!gpio_chips[i]) + continue; + + pio = gpio_chips[i]->regbase; + + backups[i] = __raw_readl(pio + PIO_IMR); + __raw_writel(backups[i], pio + PIO_IDR); + __raw_writel(wakeups[i], pio + PIO_IER); + + if (!wakeups[i]) { + clk_unprepare(gpio_chips[i]->clock); + clk_disable(gpio_chips[i]->clock); + } else { + printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", + 'A'+i, wakeups[i]); + } + } +} + +void at91_pinctrl_gpio_resume(void) +{ + int i; + + for (i = 0; i < gpio_banks; i++) { + void __iomem *pio; + + if (!gpio_chips[i]) + continue; + + pio = gpio_chips[i]->regbase; + + if (!wakeups[i]) { + if (clk_prepare(gpio_chips[i]->clock) == 0) + clk_enable(gpio_chips[i]->clock); + } + + __raw_writel(wakeups[i], pio + PIO_IDR); + __raw_writel(backups[i], pio + PIO_IER); + } +} + #else #define gpio_irq_set_wake NULL -#endif +#endif /* CONFIG_PM */ static struct irq_chip gpio_irqchip = { .name = "GPIO", -- cgit v1.2.3 From 0ed66befaae893e82c9f016238282d73ef9fd6c7 Mon Sep 17 00:00:00 2001 From: Ludovic Desroches Date: Fri, 8 Mar 2013 16:13:57 +0100 Subject: ARM: at91: fix infinite loop in at91_irq_suspend/resume Fix an infinite loop when suspending or resuming a device with AIC5. Signed-off-by: Ludovic Desroches Acked-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre --- arch/arm/mach-at91/irq.c | 20 ++++++++------------ 1 file changed, 8 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/irq.c b/arch/arm/mach-at91/irq.c index 8e210262aeee..e0ca59171022 100644 --- a/arch/arm/mach-at91/irq.c +++ b/arch/arm/mach-at91/irq.c @@ -92,23 +92,21 @@ static int at91_aic_set_wake(struct irq_data *d, unsigned value) void at91_irq_suspend(void) { - int i = 0, bit; + int bit = -1; if (has_aic5()) { /* disable enabled irqs */ - while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) { + while ((bit = find_next_bit(backups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IDCR, 1); - i = bit; } /* enable wakeup irqs */ - i = 0; - while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) { + bit = -1; + while ((bit = find_next_bit(wakeups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IECR, 1); - i = bit; } } else { at91_aic_write(AT91_AIC_IDCR, *backups); @@ -118,23 +116,21 @@ void at91_irq_suspend(void) void at91_irq_resume(void) { - int i = 0, bit; + int bit = -1; if (has_aic5()) { /* disable wakeup irqs */ - while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) { + while ((bit = find_next_bit(wakeups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IDCR, 1); - i = bit; } /* enable irqs disabled for suspend */ - i = 0; - while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) { + bit = -1; + while ((bit = find_next_bit(backups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IECR, 1); - i = bit; } } else { at91_aic_write(AT91_AIC_IDCR, *wakeups); -- cgit v1.2.3 From 42b84328428bfe305fcb60eb382fba60cee9071f Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Thu, 14 Mar 2013 12:52:05 +0100 Subject: ARM: i.MX25: Fix DT compilation The i.MX25 DT machine descriptor calls a non existing imx25_timer_init() function. This patch adds it to fix compilation. Signed-off-by: Sascha Hauer --- arch/arm/mach-imx/imx25-dt.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-imx/imx25-dt.c b/arch/arm/mach-imx/imx25-dt.c index 03b65e5ea541..82348391582a 100644 --- a/arch/arm/mach-imx/imx25-dt.c +++ b/arch/arm/mach-imx/imx25-dt.c @@ -27,6 +27,11 @@ static const char * const imx25_dt_board_compat[] __initconst = { NULL }; +static void __init imx25_timer_init(void) +{ + mx25_clocks_init_dt(); +} + DT_MACHINE_START(IMX25_DT, "Freescale i.MX25 (Device Tree Support)") .map_io = mx25_map_io, .init_early = imx25_init_early, -- cgit v1.2.3 From 01ffe957e2f0340a13fd40a6577d029f252ad7c7 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Thu, 14 Feb 2013 23:11:33 +0100 Subject: [media] s5p-fimc: fix s5pv210 build 56bc911 "[media] s5p-fimc: Redefine platform data structure for fimc-is" changed the bus_type member of struct fimc_source_info treewide, but got one instance wrong in mach-s5pv210, which was evidently not even build tested. This adds the missing change to get s5pv210_defconfig to build again. Applies on the Mauro's media tree. Signed-off-by: Arnd Bergmann Cc: Sylwester Nawrocki Cc: Kyungmin Park Cc: Kukjin Kim Cc: Mauro Carvalho Chehab --- arch/arm/mach-s5pv210/mach-goni.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index 3a38f7b34b94..e373de44a8b6 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -845,7 +845,7 @@ static struct fimc_source_info goni_camera_sensors[] = { .mux_id = 0, .flags = V4L2_MBUS_PCLK_SAMPLE_FALLING | V4L2_MBUS_VSYNC_ACTIVE_LOW, - .bus_type = FIMC_BUS_TYPE_ITU_601, + .fimc_bus_type = FIMC_BUS_TYPE_ITU_601, .board_info = &noon010pc30_board_info, .i2c_bus_num = 0, .clk_frequency = 16000000UL, -- cgit v1.2.3 From e71dc5f787f3908b8b8158103fc7d74a78a22cd1 Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Fri, 15 Mar 2013 16:27:53 +0800 Subject: ARM: mmp: add platform_device head file in gplugd arch/arm/mach-mmp/gplugd.c: In function ‘gplugd_init’: arch/arm/mach-mmp/gplugd.c:188:2: error: implicit declaration of function ‘platform_device_register’ [-Werror=implicit-function-declaration] cc1: some warnings being treated as errors make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1 make: *** [arch/arm/mach-mmp] Error 2 So append platform_device.h to resolve build issue. Signed-off-by: Haojian Zhuang --- arch/arm/mach-mmp/gplugd.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c index d1e2d595e79c..f62b68d926f4 100644 --- a/arch/arm/mach-mmp/gplugd.c +++ b/arch/arm/mach-mmp/gplugd.c @@ -9,6 +9,7 @@ */ #include +#include #include #include -- cgit v1.2.3 From 8dda05ccd8a227e2b56ce6b26d52b1af88437f9e Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Mon, 4 Mar 2013 15:19:19 -0800 Subject: ARM: Scorpion is a v7 architecture, not v6 Scorpion processors have always been v7 CPUs. Fix the Kconfig text to reflect this. Reported-by: Stepan Moskovchenko Signed-off-by: Stephen Boyd Signed-off-by: Arnd Bergmann --- arch/arm/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 9c87fd8ed9eb..ca1b6fd94a3f 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1005,12 +1005,12 @@ config ARCH_MULTI_V4_V5 bool config ARCH_MULTI_V6 - bool "ARMv6 based platforms (ARM11, Scorpion, ...)" + bool "ARMv6 based platforms (ARM11)" select ARCH_MULTI_V6_V7 select CPU_V6 config ARCH_MULTI_V7 - bool "ARMv7 based platforms (Cortex-A, PJ4, Krait)" + bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)" default y select ARCH_MULTI_V6_V7 select ARCH_VEXPRESS -- cgit v1.2.3 From 5dc2eb7da1e387e31ce54f54af580c6a6f512ca6 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Tue, 26 Feb 2013 10:55:18 +0100 Subject: ARM: i.MX35: enable MAX clock The i.MX35 has two bits per clock gate which are decoded as follows: 0b00 -> clock off 0b01 -> clock is on in run mode, off in wait/doze 0b10 -> clock is on in run/wait mode, off in doze 0b11 -> clock is always on The reset value for the MAX clock is 0b10. The MAX clock is needed by the SoC, yet unused in the Kernel, so the common clock framework will disable it during late init time. It will only disable clocks though which it detects as being turned on. This detection is made depending on the lower bit of the gate. If the reset value has been altered by the bootloader to 0b11 the clock framework will detect the clock as turned on, yet unused, hence it will turn it off and the system locks up. This patch turns the MAX clock on unconditionally making the Kernel independent of the bootloader. Signed-off-by: Sascha Hauer --- arch/arm/mach-imx/clk-imx35.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-imx/clk-imx35.c b/arch/arm/mach-imx/clk-imx35.c index 74e3a34d78b8..e13a8fa5e62c 100644 --- a/arch/arm/mach-imx/clk-imx35.c +++ b/arch/arm/mach-imx/clk-imx35.c @@ -264,6 +264,7 @@ int __init mx35_clocks_init(void) clk_prepare_enable(clk[gpio3_gate]); clk_prepare_enable(clk[iim_gate]); clk_prepare_enable(clk[emi_gate]); + clk_prepare_enable(clk[max_gate]); /* * SCC is needed to boot via mmc after a watchdog reset. The clock code -- cgit v1.2.3 From b4811bacbc68f6e17d442df88f98afaa9394d4f5 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 13 Mar 2013 17:36:37 +0100 Subject: ARM: fix CONFIG_VIRT_TO_BUS handling 887cbce0 "arch Kconfig: centralise CONFIG_ARCH_NO_VIRT_TO_BUS" and 4febd95a8 "Select VIRT_TO_BUS directly where needed" from Stephen Rothwell changed globally how CONFIG_VIRT_TO_BUS is selected, while my own a5d533ee0 "ARM: disable virt_to_bus/ virt_to_bus almost everywhere" was merged at the same time and changed which platforms select it on ARM. The result of this conflict was that we again see CONFIG_VIRT_TO_BUS on all ARM systems. This patch fixes up the problem and removes CONFIG_ARCH_NO_VIRT_TO_BUS again on ARM. Signed-off-by: Arnd Bergmann Cc: Russell King Cc: Stephen Rothwell --- arch/arm/Kconfig | 7 ++----- arch/arm/mach-footbridge/Kconfig | 1 + 2 files changed, 3 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index ca1b6fd94a3f..6d6e77c89691 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -49,7 +49,6 @@ config ARM select HAVE_REGS_AND_STACK_ACCESS_API select HAVE_SYSCALL_TRACEPOINTS select HAVE_UID16 - select HAVE_VIRT_TO_BUS select KTIME_SCALAR select PERF_USE_VMALLOC select RTC_LIB @@ -743,6 +742,7 @@ config ARCH_RPC select NEED_MACH_IO_H select NEED_MACH_MEMORY_H select NO_IOPORT + select VIRT_TO_BUS help On the Acorn Risc-PC, Linux can support the internal IDE disk and CD-ROM interface, serial and parallel port, and the floppy drive. @@ -878,6 +878,7 @@ config ARCH_SHARK select ISA_DMA select NEED_MACH_MEMORY_H select PCI + select VIRT_TO_BUS select ZONE_DMA help Support for the StrongARM based Digital DNARD machine, also known @@ -1461,10 +1462,6 @@ config ISA_DMA bool select ISA_DMA_API -config ARCH_NO_VIRT_TO_BUS - def_bool y - depends on !ARCH_RPC && !ARCH_NETWINDER && !ARCH_SHARK - # Select ISA DMA interface config ISA_DMA_API bool diff --git a/arch/arm/mach-footbridge/Kconfig b/arch/arm/mach-footbridge/Kconfig index abda5a18a664..0f2111a11315 100644 --- a/arch/arm/mach-footbridge/Kconfig +++ b/arch/arm/mach-footbridge/Kconfig @@ -67,6 +67,7 @@ config ARCH_NETWINDER select ISA select ISA_DMA select PCI + select VIRT_TO_BUS help Say Y here if you intend to run this kernel on the Rebel.COM NetWinder. Information about this machine can be found at: -- cgit v1.2.3