From c265a762aa196de11f38f6f44cc817329f32a813 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 19 Dec 2006 12:24:25 +0000 Subject: [ARM] oprofile: add ARM11 core support Add basic support for the ARM11 profiling hardware. This is shared between the ARM11 UP and ARM11 SMP oprofile support code. Signed-off-by: Russell King --- arch/arm/oprofile/Kconfig | 3 + arch/arm/oprofile/Makefile | 2 +- arch/arm/oprofile/op_model_arm11_core.c | 162 ++++++++++++++++++++++++++++++++ arch/arm/oprofile/op_model_arm11_core.h | 45 +++++++++ 4 files changed, 211 insertions(+), 1 deletion(-) create mode 100644 arch/arm/oprofile/op_model_arm11_core.c create mode 100644 arch/arm/oprofile/op_model_arm11_core.h (limited to 'arch') diff --git a/arch/arm/oprofile/Kconfig b/arch/arm/oprofile/Kconfig index 19d37730b664..615a6b9503a4 100644 --- a/arch/arm/oprofile/Kconfig +++ b/arch/arm/oprofile/Kconfig @@ -19,5 +19,8 @@ config OPROFILE If unsure, say N. +config OPROFILE_ARM11_CORE + bool + endmenu diff --git a/arch/arm/oprofile/Makefile b/arch/arm/oprofile/Makefile index 6a94e54848fd..30352d6c4a25 100644 --- a/arch/arm/oprofile/Makefile +++ b/arch/arm/oprofile/Makefile @@ -8,4 +8,4 @@ DRIVER_OBJS = $(addprefix ../../../drivers/oprofile/, \ oprofile-y := $(DRIVER_OBJS) common.o backtrace.o oprofile-$(CONFIG_CPU_XSCALE) += op_model_xscale.o - +oprofile-$(CONFIG_OPROFILE_ARM11_CORE) += op_model_arm11_core.o diff --git a/arch/arm/oprofile/op_model_arm11_core.c b/arch/arm/oprofile/op_model_arm11_core.c new file mode 100644 index 000000000000..ad80752cb9fb --- /dev/null +++ b/arch/arm/oprofile/op_model_arm11_core.c @@ -0,0 +1,162 @@ +/** + * @file op_model_arm11_core.c + * ARM11 Event Monitor Driver + * @remark Copyright 2004 ARM SMP Development Team + */ +#include +#include +#include +#include +#include +#include + +#include "op_counter.h" +#include "op_arm_model.h" +#include "op_model_arm11_core.h" + +/* + * ARM11 PMU support + */ +static inline void arm11_write_pmnc(u32 val) +{ + /* upper 4bits and 7, 11 are write-as-0 */ + val &= 0x0ffff77f; + asm volatile("mcr p15, 0, %0, c15, c12, 0" : : "r" (val)); +} + +static inline u32 arm11_read_pmnc(void) +{ + u32 val; + asm volatile("mrc p15, 0, %0, c15, c12, 0" : "=r" (val)); + return val; +} + +static void arm11_reset_counter(unsigned int cnt) +{ + u32 val = -(u32)counter_config[CPU_COUNTER(smp_processor_id(), cnt)].count; + switch (cnt) { + case CCNT: + asm volatile("mcr p15, 0, %0, c15, c12, 1" : : "r" (val)); + break; + + case PMN0: + asm volatile("mcr p15, 0, %0, c15, c12, 2" : : "r" (val)); + break; + + case PMN1: + asm volatile("mcr p15, 0, %0, c15, c12, 3" : : "r" (val)); + break; + } +} + +int arm11_setup_pmu(void) +{ + unsigned int cnt; + u32 pmnc; + + if (arm11_read_pmnc() & PMCR_E) { + printk(KERN_ERR "oprofile: CPU%u PMU still enabled when setup new event counter.\n", smp_processor_id()); + return -EBUSY; + } + + /* initialize PMNC, reset overflow, D bit, C bit and P bit. */ + arm11_write_pmnc(PMCR_OFL_PMN0 | PMCR_OFL_PMN1 | PMCR_OFL_CCNT | + PMCR_C | PMCR_P); + + for (pmnc = 0, cnt = PMN0; cnt <= CCNT; cnt++) { + unsigned long event; + + if (!counter_config[CPU_COUNTER(smp_processor_id(), cnt)].enabled) + continue; + + event = counter_config[CPU_COUNTER(smp_processor_id(), cnt)].event & 255; + + /* + * Set event (if destined for PMNx counters) + */ + if (cnt == PMN0) { + pmnc |= event << 20; + } else if (cnt == PMN1) { + pmnc |= event << 12; + } + + /* + * We don't need to set the event if it's a cycle count + * Enable interrupt for this counter + */ + pmnc |= PMCR_IEN_PMN0 << cnt; + arm11_reset_counter(cnt); + } + arm11_write_pmnc(pmnc); + + return 0; +} + +int arm11_start_pmu(void) +{ + arm11_write_pmnc(arm11_read_pmnc() | PMCR_E); + return 0; +} + +int arm11_stop_pmu(void) +{ + unsigned int cnt; + + arm11_write_pmnc(arm11_read_pmnc() & ~PMCR_E); + + for (cnt = PMN0; cnt <= CCNT; cnt++) + arm11_reset_counter(cnt); + + return 0; +} + +/* + * CPU counters' IRQ handler (one IRQ per CPU) + */ +static irqreturn_t arm11_pmu_interrupt(int irq, void *arg) +{ + struct pt_regs *regs = get_irq_regs(); + unsigned int cnt; + u32 pmnc; + + pmnc = arm11_read_pmnc(); + + for (cnt = PMN0; cnt <= CCNT; cnt++) { + if ((pmnc & (PMCR_OFL_PMN0 << cnt)) && (pmnc & (PMCR_IEN_PMN0 << cnt))) { + arm11_reset_counter(cnt); + oprofile_add_sample(regs, CPU_COUNTER(smp_processor_id(), cnt)); + } + } + /* Clear counter flag(s) */ + arm11_write_pmnc(pmnc); + return IRQ_HANDLED; +} + +int arm11_request_interrupts(int *irqs, int nr) +{ + unsigned int i; + int ret = 0; + + for(i = 0; i < nr; i++) { + ret = request_irq(irqs[i], arm11_pmu_interrupt, IRQF_DISABLED, "CP15 PMU", NULL); + if (ret != 0) { + printk(KERN_ERR "oprofile: unable to request IRQ%u for MPCORE-EM\n", + irqs[i]); + break; + } + } + + if (i != nr) + while (i-- != 0) + free_irq(irqs[i], NULL); + + return ret; +} + +void arm11_release_interrupts(int *irqs, int nr) +{ + unsigned int i; + + for (i = 0; i < nr; i++) + free_irq(irqs[i], NULL); +} diff --git a/arch/arm/oprofile/op_model_arm11_core.h b/arch/arm/oprofile/op_model_arm11_core.h new file mode 100644 index 000000000000..6f8538e5a960 --- /dev/null +++ b/arch/arm/oprofile/op_model_arm11_core.h @@ -0,0 +1,45 @@ +/** + * @file op_model_arm11_core.h + * ARM11 Event Monitor Driver + * @remark Copyright 2004 ARM SMP Development Team + * @remark Copyright 2000-2004 Deepak Saxena + * @remark Copyright 2000-2004 MontaVista Software Inc + * @remark Copyright 2004 Dave Jiang + * @remark Copyright 2004 Intel Corporation + * @remark Copyright 2004 Zwane Mwaikambo + * @remark Copyright 2004 Oprofile Authors + * + * @remark Read the file COPYING + * + * @author Zwane Mwaikambo + */ +#ifndef OP_MODEL_ARM11_CORE_H +#define OP_MODEL_ARM11_CORE_H + +/* + * Per-CPU PMCR + */ +#define PMCR_E (1 << 0) /* Enable */ +#define PMCR_P (1 << 1) /* Count reset */ +#define PMCR_C (1 << 2) /* Cycle counter reset */ +#define PMCR_D (1 << 3) /* Cycle counter counts every 64th cpu cycle */ +#define PMCR_IEN_PMN0 (1 << 4) /* Interrupt enable count reg 0 */ +#define PMCR_IEN_PMN1 (1 << 5) /* Interrupt enable count reg 1 */ +#define PMCR_IEN_CCNT (1 << 6) /* Interrupt enable cycle counter */ +#define PMCR_OFL_PMN0 (1 << 8) /* Count reg 0 overflow */ +#define PMCR_OFL_PMN1 (1 << 9) /* Count reg 1 overflow */ +#define PMCR_OFL_CCNT (1 << 10) /* Cycle counter overflow */ + +#define PMN0 0 +#define PMN1 1 +#define CCNT 2 + +#define CPU_COUNTER(cpu, counter) ((cpu) * 3 + (counter)) + +int arm11_setup_pmu(void); +int arm11_start_pmu(void); +int arm11_stop_pmu(void); +int arm11_request_interrupts(int *, int); +void arm11_release_interrupts(int *, int); + +#endif -- cgit v1.2.3 From 2d9e1ae06d8f0bb187ea083fabab2dfb6f589270 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 19 Dec 2006 12:41:22 +0000 Subject: [ARM] oprofile: add ARM11 UP support Add oprofile glue for ARM11 (ARMv6) oprofile support. This connects the ARM11 core profiling support to the oprofile code for uniprocessor configurations. Signed-off-by: Russell King --- arch/arm/oprofile/Kconfig | 10 ++++++ arch/arm/oprofile/Makefile | 1 + arch/arm/oprofile/common.c | 4 +++ arch/arm/oprofile/op_arm_model.h | 2 ++ arch/arm/oprofile/op_model_v6.c | 67 ++++++++++++++++++++++++++++++++++++++++ 5 files changed, 84 insertions(+) create mode 100644 arch/arm/oprofile/op_model_v6.c (limited to 'arch') diff --git a/arch/arm/oprofile/Kconfig b/arch/arm/oprofile/Kconfig index 615a6b9503a4..40cc1894b517 100644 --- a/arch/arm/oprofile/Kconfig +++ b/arch/arm/oprofile/Kconfig @@ -19,8 +19,18 @@ config OPROFILE If unsure, say N. +if OPROFILE + +config OPROFILE_ARMV6 + bool + depends on CPU_V6 && !SMP + default y + select OPROFILE_ARM11_CORE + config OPROFILE_ARM11_CORE bool +endif + endmenu diff --git a/arch/arm/oprofile/Makefile b/arch/arm/oprofile/Makefile index 30352d6c4a25..3d5ff306db78 100644 --- a/arch/arm/oprofile/Makefile +++ b/arch/arm/oprofile/Makefile @@ -9,3 +9,4 @@ DRIVER_OBJS = $(addprefix ../../../drivers/oprofile/, \ oprofile-y := $(DRIVER_OBJS) common.o backtrace.o oprofile-$(CONFIG_CPU_XSCALE) += op_model_xscale.o oprofile-$(CONFIG_OPROFILE_ARM11_CORE) += op_model_arm11_core.o +oprofile-$(CONFIG_OPROFILE_ARMV6) += op_model_v6.o diff --git a/arch/arm/oprofile/common.c b/arch/arm/oprofile/common.c index 6f833358cd06..f1b24fbd8e67 100644 --- a/arch/arm/oprofile/common.c +++ b/arch/arm/oprofile/common.c @@ -135,6 +135,10 @@ int __init oprofile_arch_init(struct oprofile_operations *ops) spec = &op_xscale_spec; #endif +#ifdef CONFIG_OPROFILE_ARMV6 + spec = &op_armv6_spec; +#endif + if (spec) { ret = spec->init(); if (ret < 0) diff --git a/arch/arm/oprofile/op_arm_model.h b/arch/arm/oprofile/op_arm_model.h index 38c6ad158547..ad1c962ed17b 100644 --- a/arch/arm/oprofile/op_arm_model.h +++ b/arch/arm/oprofile/op_arm_model.h @@ -24,6 +24,8 @@ struct op_arm_model_spec { extern struct op_arm_model_spec op_xscale_spec; #endif +extern struct op_arm_model_spec op_armv6_spec; + extern void arm_backtrace(struct pt_regs * const regs, unsigned int depth); extern int __init op_arm_init(struct oprofile_operations *ops, struct op_arm_model_spec *spec); diff --git a/arch/arm/oprofile/op_model_v6.c b/arch/arm/oprofile/op_model_v6.c new file mode 100644 index 000000000000..fe581383d3e2 --- /dev/null +++ b/arch/arm/oprofile/op_model_v6.c @@ -0,0 +1,67 @@ +/** + * @file op_model_v6.c + * ARM11 Performance Monitor Driver + * + * Based on op_model_xscale.c + * + * @remark Copyright 2000-2004 Deepak Saxena + * @remark Copyright 2000-2004 MontaVista Software Inc + * @remark Copyright 2004 Dave Jiang + * @remark Copyright 2004 Intel Corporation + * @remark Copyright 2004 Zwane Mwaikambo + * @remark Copyright 2004 OProfile Authors + * + * @remark Read the file COPYING + * + * @author Tony Lindgren + */ + +/* #define DEBUG */ +#include +#include +#include +#include +#include +#include +#include + +#include "op_counter.h" +#include "op_arm_model.h" +#include "op_model_arm11_core.h" + +static int irqs[] = { +#ifdef CONFIG_ARCH_OMAP2 + 3, +#endif +}; + +static void armv6_pmu_stop(void) +{ + arm11_stop_pmu(); + arm11_release_interrupts(irqs, ARRAY_SIZE(irqs)); +} + +static int armv6_pmu_start(void) +{ + int ret; + + ret = arm11_request_interrupts(irqs, ARRAY_SIZE(irqs)); + if (ret >= 0) + ret = arm11_start_pmu(); + + return ret; +} + +static int armv6_detect_pmu(void) +{ + return 0; +} + +struct op_arm_model_spec op_armv6_spec = { + .init = armv6_detect_pmu, + .num_counters = 3, + .setup_ctrs = arm11_setup_pmu, + .start = armv6_pmu_start, + .stop = armv6_pmu_stop, + .name = "arm/armv6", +}; -- cgit v1.2.3 From 10c03f69680e9e2acd8a9409a230aef37295ac49 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 19 Dec 2006 14:17:46 +0000 Subject: [ARM] oprofile: add ARM11 SMP support Add the glue for ARM11 SMP oprofile support, which also supports the performance monitor in the coherency unit. Signed-off-by: Russell King --- arch/arm/oprofile/Kconfig | 6 + arch/arm/oprofile/Makefile | 1 + arch/arm/oprofile/common.c | 4 + arch/arm/oprofile/op_arm_model.h | 1 + arch/arm/oprofile/op_model_mpcore.c | 296 +++++++++++++++++++++++++++++++++++ arch/arm/oprofile/op_model_mpcore.h | 61 ++++++++ include/asm-arm/arch-realview/irqs.h | 12 ++ 7 files changed, 381 insertions(+) create mode 100644 arch/arm/oprofile/op_model_mpcore.c create mode 100644 arch/arm/oprofile/op_model_mpcore.h (limited to 'arch') diff --git a/arch/arm/oprofile/Kconfig b/arch/arm/oprofile/Kconfig index 40cc1894b517..afd93ad02feb 100644 --- a/arch/arm/oprofile/Kconfig +++ b/arch/arm/oprofile/Kconfig @@ -27,6 +27,12 @@ config OPROFILE_ARMV6 default y select OPROFILE_ARM11_CORE +config OPROFILE_MPCORE + bool + depends on CPU_V6 && SMP + default y + select OPROFILE_ARM11_CORE + config OPROFILE_ARM11_CORE bool diff --git a/arch/arm/oprofile/Makefile b/arch/arm/oprofile/Makefile index 3d5ff306db78..e61d0cc520b7 100644 --- a/arch/arm/oprofile/Makefile +++ b/arch/arm/oprofile/Makefile @@ -10,3 +10,4 @@ oprofile-y := $(DRIVER_OBJS) common.o backtrace.o oprofile-$(CONFIG_CPU_XSCALE) += op_model_xscale.o oprofile-$(CONFIG_OPROFILE_ARM11_CORE) += op_model_arm11_core.o oprofile-$(CONFIG_OPROFILE_ARMV6) += op_model_v6.o +oprofile-$(CONFIG_OPROFILE_MPCORE) += op_model_mpcore.o diff --git a/arch/arm/oprofile/common.c b/arch/arm/oprofile/common.c index f1b24fbd8e67..0a007b931f63 100644 --- a/arch/arm/oprofile/common.c +++ b/arch/arm/oprofile/common.c @@ -139,6 +139,10 @@ int __init oprofile_arch_init(struct oprofile_operations *ops) spec = &op_armv6_spec; #endif +#ifdef CONFIG_OPROFILE_MPCORE + spec = &op_mpcore_spec; +#endif + if (spec) { ret = spec->init(); if (ret < 0) diff --git a/arch/arm/oprofile/op_arm_model.h b/arch/arm/oprofile/op_arm_model.h index ad1c962ed17b..4899c629aa03 100644 --- a/arch/arm/oprofile/op_arm_model.h +++ b/arch/arm/oprofile/op_arm_model.h @@ -25,6 +25,7 @@ extern struct op_arm_model_spec op_xscale_spec; #endif extern struct op_arm_model_spec op_armv6_spec; +extern struct op_arm_model_spec op_mpcore_spec; extern void arm_backtrace(struct pt_regs * const regs, unsigned int depth); diff --git a/arch/arm/oprofile/op_model_mpcore.c b/arch/arm/oprofile/op_model_mpcore.c new file mode 100644 index 000000000000..898500718249 --- /dev/null +++ b/arch/arm/oprofile/op_model_mpcore.c @@ -0,0 +1,296 @@ +/** + * @file op_model_mpcore.c + * MPCORE Event Monitor Driver + * @remark Copyright 2004 ARM SMP Development Team + * @remark Copyright 2000-2004 Deepak Saxena + * @remark Copyright 2000-2004 MontaVista Software Inc + * @remark Copyright 2004 Dave Jiang + * @remark Copyright 2004 Intel Corporation + * @remark Copyright 2004 Zwane Mwaikambo + * @remark Copyright 2004 Oprofile Authors + * + * @remark Read the file COPYING + * + * @author Zwane Mwaikambo + * + * Counters: + * 0: PMN0 on CPU0, per-cpu configurable event counter + * 1: PMN1 on CPU0, per-cpu configurable event counter + * 2: CCNT on CPU0 + * 3: PMN0 on CPU1 + * 4: PMN1 on CPU1 + * 5: CCNT on CPU1 + * 6: PMN0 on CPU1 + * 7: PMN1 on CPU1 + * 8: CCNT on CPU1 + * 9: PMN0 on CPU1 + * 10: PMN1 on CPU1 + * 11: CCNT on CPU1 + * 12-19: configurable SCU event counters + */ + +/* #define DEBUG */ +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include "op_counter.h" +#include "op_arm_model.h" +#include "op_model_arm11_core.h" +#include "op_model_mpcore.h" + +/* + * MPCore SCU event monitor support + */ +#define SCU_EVENTMONITORS_VA_BASE __io_address(REALVIEW_MPCORE_SCU_BASE + 0x10) + +/* + * Bitmask of used SCU counters + */ +static unsigned int scu_em_used; + +/* + * 2 helper fns take a counter number from 0-7 (not the userspace-visible counter number) + */ +static inline void scu_reset_counter(struct eventmonitor __iomem *emc, unsigned int n) +{ + writel(-(u32)counter_config[SCU_COUNTER(n)].count, &emc->MC[n]); +} + +static inline void scu_set_event(struct eventmonitor __iomem *emc, unsigned int n, u32 event) +{ + event &= 0xff; + writeb(event, &emc->MCEB[n]); +} + +/* + * SCU counters' IRQ handler (one IRQ per counter => 2 IRQs per CPU) + */ +static irqreturn_t scu_em_interrupt(int irq, void *arg) +{ + struct eventmonitor __iomem *emc = SCU_EVENTMONITORS_VA_BASE; + unsigned int cnt; + + cnt = irq - IRQ_PMU_SCU0; + oprofile_add_sample(get_irq_regs(), SCU_COUNTER(cnt)); + scu_reset_counter(emc, cnt); + + /* Clear overflow flag for this counter */ + writel(1 << (cnt + 16), &emc->PMCR); + + return IRQ_HANDLED; +} + +/* Configure just the SCU counters that the user has requested */ +static void scu_setup(void) +{ + struct eventmonitor __iomem *emc = SCU_EVENTMONITORS_VA_BASE; + unsigned int i; + + scu_em_used = 0; + + for (i = 0; i < NUM_SCU_COUNTERS; i++) { + if (counter_config[SCU_COUNTER(i)].enabled && + counter_config[SCU_COUNTER(i)].event) { + scu_set_event(emc, i, 0); /* disable counter for now */ + scu_em_used |= 1 << i; + } + } +} + +static int scu_start(void) +{ + struct eventmonitor __iomem *emc = SCU_EVENTMONITORS_VA_BASE; + unsigned int temp, i; + unsigned long event; + int ret = 0; + + /* + * request the SCU counter interrupts that we need + */ + for (i = 0; i < NUM_SCU_COUNTERS; i++) { + if (scu_em_used & (1 << i)) { + ret = request_irq(IRQ_PMU_SCU0 + i, scu_em_interrupt, IRQF_DISABLED, "SCU PMU", NULL); + if (ret) { + printk(KERN_ERR "oprofile: unable to request IRQ%u for SCU Event Monitor\n", + IRQ_PMU_SCU0 + i); + goto err_free_scu; + } + } + } + + /* + * clear overflow and enable interrupt for all used counters + */ + temp = readl(&emc->PMCR); + for (i = 0; i < NUM_SCU_COUNTERS; i++) { + if (scu_em_used & (1 << i)) { + scu_reset_counter(emc, i); + event = counter_config[SCU_COUNTER(i)].event; + scu_set_event(emc, i, event); + + /* clear overflow/interrupt */ + temp |= 1 << (i + 16); + /* enable interrupt*/ + temp |= 1 << (i + 8); + } + } + + /* Enable all 8 counters */ + temp |= PMCR_E; + writel(temp, &emc->PMCR); + + return 0; + + err_free_scu: + while (i--) + free_irq(IRQ_PMU_SCU0 + i, NULL); + return ret; +} + +static void scu_stop(void) +{ + struct eventmonitor __iomem *emc = SCU_EVENTMONITORS_VA_BASE; + unsigned int temp, i; + + /* Disable counter interrupts */ + /* Don't disable all 8 counters (with the E bit) as they may be in use */ + temp = readl(&emc->PMCR); + for (i = 0; i < NUM_SCU_COUNTERS; i++) { + if (scu_em_used & (1 << i)) + temp &= ~(1 << (i + 8)); + } + writel(temp, &emc->PMCR); + + /* Free counter interrupts and reset counters */ + for (i = 0; i < NUM_SCU_COUNTERS; i++) { + if (scu_em_used & (1 << i)) { + scu_reset_counter(emc, i); + free_irq(IRQ_PMU_SCU0 + i, NULL); + } + } +} + +struct em_function_data { + int (*fn)(void); + int ret; +}; + +static void em_func(void *data) +{ + struct em_function_data *d = data; + int ret = d->fn(); + if (ret) + d->ret = ret; +} + +static int em_call_function(int (*fn)(void)) +{ + struct em_function_data data; + + data.fn = fn; + data.ret = 0; + + smp_call_function(em_func, &data, 1, 1); + em_func(&data); + + return data.ret; +} + +/* + * Glue to stick the individual ARM11 PMUs and the SCU + * into the oprofile framework. + */ +static int em_setup_ctrs(void) +{ + int ret; + + /* Configure CPU counters by cross-calling to the other CPUs */ + ret = em_call_function(arm11_setup_pmu); + if (ret == 0) + scu_setup(); + + return 0; +} + +static int arm11_irqs[] = { + [0] = IRQ_PMU_CPU0, + [1] = IRQ_PMU_CPU1, + [2] = IRQ_PMU_CPU2, + [3] = IRQ_PMU_CPU3 +}; + +static int em_start(void) +{ + int ret; + + ret = arm11_request_interrupts(arm11_irqs, ARRAY_SIZE(arm11_irqs)); + if (ret == 0) { + em_call_function(arm11_start_pmu); + + ret = scu_start(); + if (ret) + arm11_release_interrupts(arm11_irqs, ARRAY_SIZE(arm11_irqs)); + } + return ret; +} + +static void em_stop(void) +{ + em_call_function(arm11_stop_pmu); + arm11_release_interrupts(arm11_irqs, ARRAY_SIZE(arm11_irqs)); + scu_stop(); +} + +/* + * Why isn't there a function to route an IRQ to a specific CPU in + * genirq? + */ +static void em_route_irq(int irq, unsigned int cpu) +{ + irq_desc[irq].affinity = cpumask_of_cpu(cpu); + irq_desc[irq].chip->set_affinity(irq, cpumask_of_cpu(cpu)); +} + +static int em_setup(void) +{ + /* + * Send SCU PMU interrupts to the "owner" CPU. + */ + em_route_irq(IRQ_PMU_SCU0, 0); + em_route_irq(IRQ_PMU_SCU1, 0); + em_route_irq(IRQ_PMU_SCU2, 1); + em_route_irq(IRQ_PMU_SCU3, 1); + em_route_irq(IRQ_PMU_SCU4, 2); + em_route_irq(IRQ_PMU_SCU5, 2); + em_route_irq(IRQ_PMU_SCU6, 3); + em_route_irq(IRQ_PMU_SCU7, 3); + + /* + * Send CP15 PMU interrupts to the owner CPU. + */ + em_route_irq(IRQ_PMU_CPU0, 0); + em_route_irq(IRQ_PMU_CPU1, 1); + em_route_irq(IRQ_PMU_CPU2, 2); + em_route_irq(IRQ_PMU_CPU3, 3); + + return 0; +} + +struct op_arm_model_spec op_mpcore_spec = { + .init = em_setup, + .num_counters = MPCORE_NUM_COUNTERS, + .setup_ctrs = em_setup_ctrs, + .start = em_start, + .stop = em_stop, + .name = "arm/mpcore", +}; diff --git a/arch/arm/oprofile/op_model_mpcore.h b/arch/arm/oprofile/op_model_mpcore.h new file mode 100644 index 000000000000..73d811023688 --- /dev/null +++ b/arch/arm/oprofile/op_model_mpcore.h @@ -0,0 +1,61 @@ +/** + * @file op_model_mpcore.c + * MPCORE Event Monitor Driver + * @remark Copyright 2004 ARM SMP Development Team + * @remark Copyright 2000-2004 Deepak Saxena + * @remark Copyright 2000-2004 MontaVista Software Inc + * @remark Copyright 2004 Dave Jiang + * @remark Copyright 2004 Intel Corporation + * @remark Copyright 2004 Zwane Mwaikambo + * @remark Copyright 2004 Oprofile Authors + * + * @remark Read the file COPYING + * + * @author Zwane Mwaikambo + */ +#ifndef OP_MODEL_MPCORE_H +#define OP_MODEL_MPCORE_H + +struct eventmonitor { + unsigned long PMCR; + unsigned char MCEB[8]; + unsigned long MC[8]; +}; + +/* + * List of userspace counter numbers: note that the structure is important. + * The code relies on CPUn's counters being CPU0's counters + 3n + * and on CPU0's counters starting at 0 + */ + +#define COUNTER_CPU0_PMN0 0 +#define COUNTER_CPU0_PMN1 1 +#define COUNTER_CPU0_CCNT 2 + +#define COUNTER_CPU1_PMN0 3 +#define COUNTER_CPU1_PMN1 4 +#define COUNTER_CPU1_CCNT 5 + +#define COUNTER_CPU2_PMN0 6 +#define COUNTER_CPU2_PMN1 7 +#define COUNTER_CPU2_CCNT 8 + +#define COUNTER_CPU3_PMN0 9 +#define COUNTER_CPU3_PMN1 10 +#define COUNTER_CPU3_CCNT 11 + +#define COUNTER_SCU_MN0 12 +#define COUNTER_SCU_MN1 13 +#define COUNTER_SCU_MN2 14 +#define COUNTER_SCU_MN3 15 +#define COUNTER_SCU_MN4 16 +#define COUNTER_SCU_MN5 17 +#define COUNTER_SCU_MN6 18 +#define COUNTER_SCU_MN7 19 +#define NUM_SCU_COUNTERS 8 + +#define SCU_COUNTER(number) ((number) + COUNTER_SCU_MN0) + +#define MPCORE_NUM_COUNTERS SCU_COUNTER(NUM_SCU_COUNTERS) + +#endif diff --git a/include/asm-arm/arch-realview/irqs.h b/include/asm-arm/arch-realview/irqs.h index c16223c9588d..76b498eb20a6 100644 --- a/include/asm-arm/arch-realview/irqs.h +++ b/include/asm-arm/arch-realview/irqs.h @@ -65,6 +65,18 @@ #define IRQ_AACI (IRQ_GIC_START + INT_AACI) #define IRQ_ETH (IRQ_GIC_START + INT_ETH) #define IRQ_USB (IRQ_GIC_START + INT_USB) +#define IRQ_PMU_CPU0 (IRQ_GIC_START + INT_PMU_CPU0) +#define IRQ_PMU_CPU1 (IRQ_GIC_START + INT_PMU_CPU1) +#define IRQ_PMU_CPU2 (IRQ_GIC_START + INT_PMU_CPU2) +#define IRQ_PMU_CPU3 (IRQ_GIC_START + INT_PMU_CPU3) +#define IRQ_PMU_SCU0 (IRQ_GIC_START + INT_PMU_SCU0) +#define IRQ_PMU_SCU1 (IRQ_GIC_START + INT_PMU_SCU1) +#define IRQ_PMU_SCU2 (IRQ_GIC_START + INT_PMU_SCU2) +#define IRQ_PMU_SCU3 (IRQ_GIC_START + INT_PMU_SCU3) +#define IRQ_PMU_SCU4 (IRQ_GIC_START + INT_PMU_SCU4) +#define IRQ_PMU_SCU5 (IRQ_GIC_START + INT_PMU_SCU5) +#define IRQ_PMU_SCU6 (IRQ_GIC_START + INT_PMU_SCU6) +#define IRQ_PMU_SCU7 (IRQ_GIC_START + INT_PMU_SCU7) #define IRQMASK_WDOGINT INTMASK_WDOGINT #define IRQMASK_SOFTINT INTMASK_SOFTINT -- cgit v1.2.3 From 6e98a2f88e65d57cff9c98ce1744ff8e4498de31 Mon Sep 17 00:00:00 2001 From: Michael-Luke Jones Date: Sat, 16 Dec 2006 23:01:58 +0100 Subject: [ARM] 4031/1: Remove references to the Avila in ixdp425 setup code This patch removes references to the Gateworks Avila Network Platform in the ixdp425 setup code. Avila setup should occur separately now that a CF ATA device driver is available. Signed-off-by: Michael-Luke Jones Signed-off-by: Deepak Saxena Signed-off-by: Russell King --- arch/arm/mach-ixp4xx/ixdp425-pci.c | 2 +- arch/arm/mach-ixp4xx/ixdp425-setup.c | 20 -------------------- 2 files changed, 1 insertion(+), 21 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-ixp4xx/ixdp425-pci.c b/arch/arm/mach-ixp4xx/ixdp425-pci.c index d5156c043f0b..99c1dc8033c8 100644 --- a/arch/arm/mach-ixp4xx/ixdp425-pci.c +++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c @@ -66,7 +66,7 @@ struct hw_pci ixdp425_pci __initdata = { int __init ixdp425_pci_init(void) { if (machine_is_ixdp425() || machine_is_ixcdp1100() || - machine_is_avila() || machine_is_ixdp465()) + machine_is_ixdp465()) pci_common_init(&ixdp425_pci); return 0; } diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c index da72383ee301..04b1d56396a0 100644 --- a/arch/arm/mach-ixp4xx/ixdp425-setup.c +++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c @@ -156,23 +156,3 @@ MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform") .init_machine = ixdp425_init, MACHINE_END #endif - -/* - * Avila is functionally equivalent to IXDP425 except that it adds - * a CF IDE slot hanging off the expansion bus. When we have a - * driver for IXP4xx CF IDE with driver model support we'll move - * Avila to it's own setup file. - */ -#ifdef CONFIG_ARCH_AVILA -MACHINE_START(AVILA, "Gateworks Avila Network Platform") - /* Maintainer: Deepak Saxena */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, - .map_io = ixp4xx_map_io, - .init_irq = ixp4xx_init_irq, - .timer = &ixp4xx_timer, - .boot_params = 0x0100, - .init_machine = ixdp425_init, -MACHINE_END -#endif - -- cgit v1.2.3 From 0f1859719537acf5a611fd18be5d81c0cfd5fbf4 Mon Sep 17 00:00:00 2001 From: Michael-Luke Jones Date: Sat, 16 Dec 2006 23:04:05 +0100 Subject: [ARM] 4033/1: Add separate Avila board setup code This patch adds support for the Gateworks Avila Network Platform in a separate set of setup files to the IXDP425. This is necessary now that a driver for the Avila CF card slot is available. It also adds support for a minor variant on the Avila board known as the Loft, which has a different number of maximum PCI devices. Signed-off-by: Michael-Luke Jones Signed-off-by: Deepak Saxena Signed-off-by: Russell King --- arch/arm/mach-ixp4xx/Kconfig | 12 ++- arch/arm/mach-ixp4xx/Makefile | 2 + arch/arm/mach-ixp4xx/avila-pci.c | 78 +++++++++++++++++ arch/arm/mach-ixp4xx/avila-setup.c | 152 +++++++++++++++++++++++++++++++++ include/asm-arm/arch-ixp4xx/avila.h | 39 +++++++++ include/asm-arm/arch-ixp4xx/hardware.h | 1 + include/asm-arm/arch-ixp4xx/irqs.h | 9 ++ 7 files changed, 291 insertions(+), 2 deletions(-) create mode 100644 arch/arm/mach-ixp4xx/avila-pci.c create mode 100644 arch/arm/mach-ixp4xx/avila-setup.c create mode 100644 include/asm-arm/arch-ixp4xx/avila.h (limited to 'arch') diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig index e316bd93313f..8a339cdfe222 100644 --- a/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig @@ -17,7 +17,7 @@ config MACH_NSLU2 NSLU2 NAS device. For more information on this platform, see http://www.nslu2-linux.org -config ARCH_AVILA +config MACH_AVILA bool "Avila" select PCI help @@ -25,6 +25,14 @@ config ARCH_AVILA Avila Network Platform. For more information on this platform, see . +config MACH_LOFT + bool "Loft" + depends on MACH_AVILA + help + Say 'Y' here if you want your kernel to support the Giant + Shoulder Inc Loft board (a minor variation on the standard + Gateworks Avila Network Platform). + config ARCH_ADI_COYOTE bool "Coyote" select PCI @@ -86,7 +94,7 @@ config MACH_NAS100D # config ARCH_IXDP4XX bool - depends on ARCH_IXDP425 || ARCH_AVILA || MACH_IXDP465 + depends on ARCH_IXDP425 || MACH_IXDP465 default y # diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile index 640315d8b96a..746e297284ed 100644 --- a/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile @@ -6,6 +6,7 @@ obj-pci-y := obj-pci-n := obj-pci-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o +obj-pci-$(CONFIG_MACH_AVILA) += avila-pci.o obj-pci-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o obj-pci-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o obj-pci-$(CONFIG_MACH_GTWX5715) += gtwx5715-pci.o @@ -15,6 +16,7 @@ obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o obj-y += common.o obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-setup.o +obj-$(CONFIG_MACH_AVILA) += avila-setup.o obj-$(CONFIG_MACH_IXDPG425) += coyote-setup.o obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-setup.o obj-$(CONFIG_MACH_GTWX5715) += gtwx5715-setup.o diff --git a/arch/arm/mach-ixp4xx/avila-pci.c b/arch/arm/mach-ixp4xx/avila-pci.c new file mode 100644 index 000000000000..3f867691d9f2 --- /dev/null +++ b/arch/arm/mach-ixp4xx/avila-pci.c @@ -0,0 +1,78 @@ +/* + * arch/arm/mach-ixp4xx/avila-pci.c + * + * Gateworks Avila board-level PCI initialization + * + * Author: Michael-Luke Jones + * + * Based on ixdp-pci.c + * Copyright (C) 2002 Intel Corporation. + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * + * Maintainer: Deepak Saxena + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +void __init avila_pci_preinit(void) +{ + set_irq_type(IRQ_AVILA_PCI_INTA, IRQT_LOW); + set_irq_type(IRQ_AVILA_PCI_INTB, IRQT_LOW); + set_irq_type(IRQ_AVILA_PCI_INTC, IRQT_LOW); + set_irq_type(IRQ_AVILA_PCI_INTD, IRQT_LOW); + + ixp4xx_pci_preinit(); +} + +static int __init avila_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + static int pci_irq_table[AVILA_PCI_IRQ_LINES] = { + IRQ_AVILA_PCI_INTA, + IRQ_AVILA_PCI_INTB, + IRQ_AVILA_PCI_INTC, + IRQ_AVILA_PCI_INTD + }; + + int irq = -1; + + if (slot >= 1 && + slot <= (machine_is_loft() ? LOFT_PCI_MAX_DEV : AVILA_PCI_MAX_DEV) && + pin >= 1 && pin <= AVILA_PCI_IRQ_LINES) { + irq = pci_irq_table[(slot + pin - 2) % 4]; + } + + return irq; +} + +struct hw_pci avila_pci __initdata = { + .nr_controllers = 1, + .preinit = avila_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = ixp4xx_setup, + .scan = ixp4xx_scan_bus, + .map_irq = avila_map_irq, +}; + +int __init avila_pci_init(void) +{ + if (machine_is_avila() || machine_is_loft()) + pci_common_init(&avila_pci); + return 0; +} + +subsys_initcall(avila_pci_init); + diff --git a/arch/arm/mach-ixp4xx/avila-setup.c b/arch/arm/mach-ixp4xx/avila-setup.c new file mode 100644 index 000000000000..9f09f94593a6 --- /dev/null +++ b/arch/arm/mach-ixp4xx/avila-setup.c @@ -0,0 +1,152 @@ +/* + * arch/arm/mach-ixp4xx/avila-setup.c + * + * Gateworks Avila board-setup + * + * Author: Michael-Luke Jones + * + * Based on ixdp-setup.c + * Copyright (C) 2003-2005 MontaVista Software, Inc. + * + * Author: Deepak Saxena + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +static struct flash_platform_data avila_flash_data = { + .map_name = "cfi_probe", + .width = 2, +}; + +static struct resource avila_flash_resource = { + .flags = IORESOURCE_MEM, +}; + +static struct platform_device avila_flash = { + .name = "IXP4XX-Flash", + .id = 0, + .dev = { + .platform_data = &avila_flash_data, + }, + .num_resources = 1, + .resource = &avila_flash_resource, +}; + +static struct ixp4xx_i2c_pins avila_i2c_gpio_pins = { + .sda_pin = AVILA_SDA_PIN, + .scl_pin = AVILA_SCL_PIN, +}; + +static struct platform_device avila_i2c_controller = { + .name = "IXP4XX-I2C", + .id = 0, + .dev = { + .platform_data = &avila_i2c_gpio_pins, + }, + .num_resources = 0 +}; + +static struct resource avila_uart_resources[] = { + { + .start = IXP4XX_UART1_BASE_PHYS, + .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM + }, + { + .start = IXP4XX_UART2_BASE_PHYS, + .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM + } +}; + +static struct plat_serial8250_port avila_uart_data[] = { + { + .mapbase = IXP4XX_UART1_BASE_PHYS, + .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART1, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { + .mapbase = IXP4XX_UART2_BASE_PHYS, + .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { }, +}; + +static struct platform_device avila_uart = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev.platform_data = avila_uart_data, + .num_resources = 2, + .resource = avila_uart_resources +}; + +static struct platform_device *avila_devices[] __initdata = { + &avila_i2c_controller, + &avila_flash, + &avila_uart +}; + +static void __init avila_init(void) +{ + ixp4xx_sys_init(); + + avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); + avila_flash_resource.end = + IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; + + platform_add_devices(avila_devices, ARRAY_SIZE(avila_devices)); +} + +MACHINE_START(AVILA, "Gateworks Avila Network Platform") + /* Maintainer: Deepak Saxena */ + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, + .map_io = ixp4xx_map_io, + .init_irq = ixp4xx_init_irq, + .timer = &ixp4xx_timer, + .boot_params = 0x0100, + .init_machine = avila_init, +MACHINE_END + + /* + * Loft is functionally equivalent to Avila except that it has a + * different number for the maximum PCI devices. The MACHINE + * structure below is identical to Avila except for the comment. + */ +#ifdef CONFIG_MACH_LOFT +MACHINE_START(LOFT, "Giant Shoulder Inc Loft board") + /* Maintainer: Tom Billman */ + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, + .map_io = ixp4xx_map_io, + .init_irq = ixp4xx_init_irq, + .timer = &ixp4xx_timer, + .boot_params = 0x0100, + .init_machine = avila_init, +MACHINE_END +#endif + diff --git a/include/asm-arm/arch-ixp4xx/avila.h b/include/asm-arm/arch-ixp4xx/avila.h new file mode 100644 index 000000000000..0dfea0ccd6ba --- /dev/null +++ b/include/asm-arm/arch-ixp4xx/avila.h @@ -0,0 +1,39 @@ +/* + * include/asm-arm/arch-ixp4xx/avila.h + * + * Gateworks Avila platform specific definitions + * + * Author: Michael-Luke Jones + * + * Based on ixdp425.h + * Author: Deepak Saxena + * + * Copyright 2004 (c) MontaVista, Software, Inc. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H__ +#error "Do not include this directly, instead #include " +#endif + +#define AVILA_SDA_PIN 7 +#define AVILA_SCL_PIN 6 + +/* + * AVILA PCI IRQs + */ +#define AVILA_PCI_MAX_DEV 4 +#define LOFT_PCI_MAX_DEV 6 +#define AVILA_PCI_IRQ_LINES 4 + + +/* PCI controller GPIO to IRQ pin mappings */ +#define AVILA_PCI_INTA_PIN 11 +#define AVILA_PCI_INTB_PIN 10 +#define AVILA_PCI_INTC_PIN 9 +#define AVILA_PCI_INTD_PIN 8 + + diff --git a/include/asm-arm/arch-ixp4xx/hardware.h b/include/asm-arm/arch-ixp4xx/hardware.h index 6acb69c95ef9..88fd0877dcc1 100644 --- a/include/asm-arm/arch-ixp4xx/hardware.h +++ b/include/asm-arm/arch-ixp4xx/hardware.h @@ -42,6 +42,7 @@ extern unsigned int processor_id; /* Platform specific details */ #include "ixdp425.h" +#include "avila.h" #include "coyote.h" #include "prpmc1100.h" #include "nslu2.h" diff --git a/include/asm-arm/arch-ixp4xx/irqs.h b/include/asm-arm/arch-ixp4xx/irqs.h index f24b763ca18e..e44a563d00ff 100644 --- a/include/asm-arm/arch-ixp4xx/irqs.h +++ b/include/asm-arm/arch-ixp4xx/irqs.h @@ -78,6 +78,15 @@ #define IRQ_IXDP425_PCI_INTC IRQ_IXP4XX_GPIO9 #define IRQ_IXDP425_PCI_INTD IRQ_IXP4XX_GPIO8 +/* + * Gateworks Avila board IRQs + */ +#define IRQ_AVILA_PCI_INTA IRQ_IXP4XX_GPIO11 +#define IRQ_AVILA_PCI_INTB IRQ_IXP4XX_GPIO10 +#define IRQ_AVILA_PCI_INTC IRQ_IXP4XX_GPIO9 +#define IRQ_AVILA_PCI_INTD IRQ_IXP4XX_GPIO8 + + /* * PrPMC1100 Board IRQs */ -- cgit v1.2.3 From 946acb1c70f91f07331d2b8691dfccf95c95ff3d Mon Sep 17 00:00:00 2001 From: Michael-Luke Jones Date: Sat, 16 Dec 2006 23:02:00 +0100 Subject: [ARM] 4032/1: Add platform resources required for CF driver This patch adds the platform resources required to support the ixp4xx-pata-cf libata driver on Avila Gateworks boards. Signed-off-by: Alessandro Zummo Signed-off-by: Michael-Luke Jones Signed-off-by: Deepak Saxena Signed-off-by: Russell King --- arch/arm/mach-ixp4xx/avila-setup.c | 40 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-ixp4xx/avila-setup.c b/arch/arm/mach-ixp4xx/avila-setup.c index 9f09f94593a6..d59b8dc7dc7a 100644 --- a/arch/arm/mach-ixp4xx/avila-setup.c +++ b/arch/arm/mach-ixp4xx/avila-setup.c @@ -104,6 +104,34 @@ static struct platform_device avila_uart = { .resource = avila_uart_resources }; +static struct resource avila_pata_resources[] = { + { + .flags = IORESOURCE_MEM + }, + { + .flags = IORESOURCE_MEM, + }, + { + .name = "intrq", + .start = IRQ_IXP4XX_GPIO12, + .end = IRQ_IXP4XX_GPIO12, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct ixp4xx_pata_data avila_pata_data = { + .cs0_bits = 0xbfff0043, + .cs1_bits = 0xbfff0043, +}; + +static struct platform_device avila_pata = { + .name = "pata_ixp4xx_cf", + .id = 0, + .dev.platform_data = &avila_pata_data, + .num_resources = ARRAY_SIZE(avila_pata_resources), + .resource = avila_pata_resources, +}; + static struct platform_device *avila_devices[] __initdata = { &avila_i2c_controller, &avila_flash, @@ -119,6 +147,18 @@ static void __init avila_init(void) IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; platform_add_devices(avila_devices, ARRAY_SIZE(avila_devices)); + + avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1); + avila_pata_resources[0].end = IXP4XX_EXP_BUS_END(1); + + avila_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2); + avila_pata_resources[1].end = IXP4XX_EXP_BUS_END(2); + + avila_pata_data.cs0_cfg = IXP4XX_EXP_CS1; + avila_pata_data.cs1_cfg = IXP4XX_EXP_CS2; + + platform_device_register(&avila_pata); + } MACHINE_START(AVILA, "Gateworks Avila Network Platform") -- cgit v1.2.3 From d941caa2537a01653704a8c1148d330a3b2755f1 Mon Sep 17 00:00:00 2001 From: Manfred Gruber Date: Sun, 17 Dec 2006 22:10:48 +0100 Subject: [ARM] 4047/1: Add initial board support for Contec Hypercontrol Micro9 boards. Contec Micro9 (H/M/L) boards based on Cirrus Logic ep93xx (ep9315/ep9307/ep9302). Signed-off-by: Manfred Gruber Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mach-ep93xx/Kconfig | 25 +++++++ arch/arm/mach-ep93xx/Makefile | 1 + arch/arm/mach-ep93xx/micro9.c | 157 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 183 insertions(+) create mode 100644 arch/arm/mach-ep93xx/micro9.c (limited to 'arch') diff --git a/arch/arm/mach-ep93xx/Kconfig b/arch/arm/mach-ep93xx/Kconfig index af7904b3d0a8..575a21dabd2f 100644 --- a/arch/arm/mach-ep93xx/Kconfig +++ b/arch/arm/mach-ep93xx/Kconfig @@ -51,6 +51,31 @@ config MACH_GESBC9312 Say 'Y' here if you want your kernel to support the Glomation GESBC-9312-sx board. +config MACH_MICRO9 + bool + default n + +config MACH_MICRO9H + bool "Support Contec Hypercontrol Micro9-H" + select MACH_MICRO9 + help + Say 'Y' here if you want your kernel to support the + Contec Hypercontrol Micro9-H board. + +config MACH_MICRO9M + bool "Support Contec Hypercontrol Micro9-M" + select MACH_MICRO9 + help + Say 'Y' here if you want your kernel to support the + Contec Hypercontrol Micro9-M board. + +config MACH_MICRO9L + bool "Support Contec Hypercontrol Micro9-L" + select MACH_MICRO9 + help + Say 'Y' here if you want your kernel to support the + Contec Hypercontrol Micro9-L board. + config MACH_TS72XX bool "Support Technologic Systems TS-72xx SBC" help diff --git a/arch/arm/mach-ep93xx/Makefile b/arch/arm/mach-ep93xx/Makefile index b06641dd450d..0d3bf932654e 100644 --- a/arch/arm/mach-ep93xx/Makefile +++ b/arch/arm/mach-ep93xx/Makefile @@ -13,4 +13,5 @@ obj-$(CONFIG_MACH_EDB9312) += edb9312.o obj-$(CONFIG_MACH_EDB9315) += edb9315.o obj-$(CONFIG_MACH_EDB9315A) += edb9315a.o obj-$(CONFIG_MACH_GESBC9312) += gesbc9312.o +obj-$(CONFIG_MACH_MICRO9) += micro9.o obj-$(CONFIG_MACH_TS72XX) += ts72xx.o diff --git a/arch/arm/mach-ep93xx/micro9.c b/arch/arm/mach-ep93xx/micro9.c new file mode 100644 index 000000000000..f28c1294cae1 --- /dev/null +++ b/arch/arm/mach-ep93xx/micro9.c @@ -0,0 +1,157 @@ +/* + * linux/arch/arm/mach-ep93xx/micro9.c + * + * Copyright (C) 2006 Contec Steuerungstechnik & Automation GmbH + * Manfred Gruber + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include + +#include +#include + +static struct ep93xx_eth_data micro9_eth_data = { + .phy_id = 0x1f, +}; + +static struct resource micro9_eth_resource[] = { + { + .start = EP93XX_ETHERNET_PHYS_BASE, + .end = EP93XX_ETHERNET_PHYS_BASE + 0xffff, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_EP93XX_ETHERNET, + .end = IRQ_EP93XX_ETHERNET, + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device micro9_eth_device = { + .name = "ep93xx-eth", + .id = -1, + .dev = { + .platform_data = µ9_eth_data, + }, + .num_resources = ARRAY_SIZE(micro9_eth_resource), + .resource = micro9_eth_resource, +}; + +static void __init micro9_eth_init(void) +{ + memcpy(micro9_eth_data.dev_addr, + (void *)(EP93XX_ETHERNET_BASE + 0x50), 6); + platform_device_register(µ9_eth_device); +} + +static void __init micro9_init(void) +{ + micro9_eth_init(); +} + +/* + * Micro9-H + */ +#ifdef CONFIG_MACH_MICRO9H +static struct physmap_flash_data micro9h_flash_data = { + .width = 4, +}; + +static struct resource micro9h_flash_resource = { + .start = 0x10000000, + .end = 0x13ffffff, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device micro9h_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = µ9h_flash_data, + }, + .num_resources = 1, + .resource = µ9h_flash_resource, +}; + +static void __init micro9h_init(void) +{ + platform_device_register(µ9h_flash); +} + +static void __init micro9h_init_machine(void) +{ + ep93xx_init_devices(); + micro9_init(); + micro9h_init(); +} + +MACHINE_START(MICRO9, "Contec Hypercontrol Micro9-H") + /* Maintainer: Manfred Gruber */ + .phys_io = EP93XX_APB_PHYS_BASE, + .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .map_io = ep93xx_map_io, + .init_irq = ep93xx_init_irq, + .timer = &ep93xx_timer, + .init_machine = micro9h_init_machine, +MACHINE_END +#endif + +/* + * Micro9-M + */ +#ifdef CONFIG_MACH_MICRO9M +static void __init micro9m_init_machine(void) +{ + ep93xx_init_devices(); + micro9_init(); +} + +MACHINE_START(MICRO9M, "Contec Hypercontrol Micro9-M") + /* Maintainer: Manfred Gruber */ + .phys_io = EP93XX_APB_PHYS_BASE, + .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .map_io = ep93xx_map_io, + .init_irq = ep93xx_init_irq, + .timer = &ep93xx_timer, + .init_machine = micro9m_init_machine, +MACHINE_END +#endif + +/* + * Micro9-L + */ +#ifdef CONFIG_MACH_MICRO9L +static void __init micro9l_init_machine(void) +{ + ep93xx_init_devices(); + micro9_init(); +} + +MACHINE_START(MICRO9L, "Contec Hypercontrol Micro9-L") + /* Maintainer: Manfred Gruber */ + .phys_io = EP93XX_APB_PHYS_BASE, + .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .map_io = ep93xx_map_io, + .init_irq = ep93xx_init_irq, + .timer = &ep93xx_timer, + .init_machine = micro9l_init_machine, +MACHINE_END +#endif + -- cgit v1.2.3 From ae0a846e411dc0b568e8ccda584896310ee5f369 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 9 Jan 2007 12:57:37 +0000 Subject: [ARM] Move processor_modes[] to .../process.c bad_mode() currently prints the mode which caused the exception, and then causes an oops dump to be printed which again displays this information (since the CPSR in the struct pt_regs is correct.) This leads to processor_modes[] being shared between traps.c and process.c with a local declaration of it. We can clean this up by moving processor_modes[] to process.c and removing the duplication, resulting in processor_modes[] becoming static. Signed-off-by: Russell King --- arch/arm/kernel/entry-armv.S | 1 - arch/arm/kernel/process.c | 8 +++++++- arch/arm/kernel/traps.c | 12 ++---------- 3 files changed, 9 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 8517c3c3eb33..cc10a093a545 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -99,7 +99,6 @@ common_invalid: @ cpsr_, "old_r0" mov r0, sp - and r2, r6, #0x1f b bad_mode /* diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index a9e8f7e55fd6..782af3cb213f 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -36,7 +36,13 @@ #include #include -extern const char *processor_modes[]; +static const char *processor_modes[] = { + "USER_26", "FIQ_26" , "IRQ_26" , "SVC_26" , "UK4_26" , "UK5_26" , "UK6_26" , "UK7_26" , + "UK8_26" , "UK9_26" , "UK10_26", "UK11_26", "UK12_26", "UK13_26", "UK14_26", "UK15_26", + "USER_32", "FIQ_32" , "IRQ_32" , "SVC_32" , "UK4_32" , "UK5_32" , "UK6_32" , "ABT_32" , + "UK8_32" , "UK9_32" , "UK10_32", "UND_32" , "UK12_32", "UK13_32", "UK14_32", "SYS_32" +}; + extern void setup_mm_for_reboot(char mode); static volatile int hlt_counter; diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 908915675edc..329609b84d3b 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -32,13 +32,6 @@ #include "ptrace.h" #include "signal.h" -const char *processor_modes[]= -{ "USER_26", "FIQ_26" , "IRQ_26" , "SVC_26" , "UK4_26" , "UK5_26" , "UK6_26" , "UK7_26" , - "UK8_26" , "UK9_26" , "UK10_26", "UK11_26", "UK12_26", "UK13_26", "UK14_26", "UK15_26", - "USER_32", "FIQ_32" , "IRQ_32" , "SVC_32" , "UK4_32" , "UK5_32" , "UK6_32" , "ABT_32" , - "UK8_32" , "UK9_32" , "UK10_32", "UND_32" , "UK12_32", "UK13_32", "UK14_32", "SYS_32" -}; - static const char *handler[]= { "prefetch abort", "data abort", "address exception", "interrupt" }; #ifdef CONFIG_DEBUG_USER @@ -337,12 +330,11 @@ asmlinkage void do_unexp_fiq (struct pt_regs *regs) * It never returns, and never tries to sync. We hope that we can at least * dump out some state information... */ -asmlinkage void bad_mode(struct pt_regs *regs, int reason, int proc_mode) +asmlinkage void bad_mode(struct pt_regs *regs, int reason) { console_verbose(); - printk(KERN_CRIT "Bad mode in %s handler detected: mode %s\n", - handler[reason], processor_modes[proc_mode]); + printk(KERN_CRIT "Bad mode in %s handler detected\n", handler[reason]); die("Oops - bad mode", regs, 0); local_irq_disable(); -- cgit v1.2.3 From a7b4e5506d1608112a208bc5391377d2c0b6dd80 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Thu, 8 Feb 2007 09:43:26 +0100 Subject: [ARM] 4144/1: Fix for patch #4099/1 with CONFIG_I2C_PXA_SLAVE set Switch the i2c-pxa driver to actually using the platform device information and let it handle the power i2c bus on pxa27x too. Original version of this patch didn't compile with CONFIG_I2C_PXA_SLAVE set. Signed-off-by: G. Liakhovetski Signed-off-by: Russell King --- arch/arm/mach-pxa/generic.c | 24 +++++ drivers/i2c/busses/i2c-pxa.c | 241 +++++++++++++++++++++++++++++-------------- 2 files changed, 188 insertions(+), 77 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c index 9de1278d234f..390524c4710f 100644 --- a/arch/arm/mach-pxa/generic.c +++ b/arch/arm/mach-pxa/generic.c @@ -338,6 +338,27 @@ static struct platform_device i2c_device = { .num_resources = ARRAY_SIZE(i2c_resources), }; +#ifdef CONFIG_PXA27x +static struct resource i2c_power_resources[] = { + { + .start = 0x40f00180, + .end = 0x40f001a3, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PWRI2C, + .end = IRQ_PWRI2C, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_power_device = { + .name = "pxa2xx-i2c", + .id = 1, + .resource = i2c_power_resources, + .num_resources = ARRAY_SIZE(i2c_resources), +}; +#endif + void __init pxa_set_i2c_info(struct i2c_pxa_platform_data *info) { i2c_device.dev.platform_data = info; @@ -392,6 +413,9 @@ static struct platform_device *devices[] __initdata = { &stuart_device, &pxaficp_device, &i2c_device, +#ifdef CONFIG_PXA27x + &i2c_power_device, +#endif &i2s_device, &pxartc_device, }; diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c index c3b1567c852a..14e83d0aac8c 100644 --- a/drivers/i2c/busses/i2c-pxa.c +++ b/drivers/i2c/busses/i2c-pxa.c @@ -34,6 +34,7 @@ #include #include +#include #include #include @@ -54,8 +55,21 @@ struct pxa_i2c { unsigned int irqlogidx; u32 isrlog[32]; u32 icrlog[32]; + + void __iomem *reg_base; + + unsigned long iobase; + unsigned long iosize; + + int irq; }; +#define _IBMR(i2c) ((i2c)->reg_base + 0) +#define _IDBR(i2c) ((i2c)->reg_base + 8) +#define _ICR(i2c) ((i2c)->reg_base + 0x10) +#define _ISR(i2c) ((i2c)->reg_base + 0x18) +#define _ISAR(i2c) ((i2c)->reg_base + 0x20) + /* * I2C Slave mode address */ @@ -130,7 +144,8 @@ static unsigned int i2c_debug = DEBUG; static void i2c_pxa_show_state(struct pxa_i2c *i2c, int lno, const char *fname) { - dev_dbg(&i2c->adap.dev, "state:%s:%d: ISR=%08x, ICR=%08x, IBMR=%02x\n", fname, lno, ISR, ICR, IBMR); + dev_dbg(&i2c->adap.dev, "state:%s:%d: ISR=%08x, ICR=%08x, IBMR=%02x\n", fname, lno, + readl(_ISR(i2c)), readl(_ICR(i2c)), readl(_IBMR(i2c))); } #define show_state(i2c) i2c_pxa_show_state(i2c, __LINE__, __FUNCTION__) @@ -153,7 +168,7 @@ static void i2c_pxa_scream_blue_murder(struct pxa_i2c *i2c, const char *why) printk("i2c: msg_num: %d msg_idx: %d msg_ptr: %d\n", i2c->msg_num, i2c->msg_idx, i2c->msg_ptr); printk("i2c: ICR: %08x ISR: %08x\n" - "i2c: log: ", ICR, ISR); + "i2c: log: ", readl(_ICR(i2c)), readl(_ISR(i2c))); for (i = 0; i < i2c->irqlogidx; i++) printk("[%08x:%08x] ", i2c->isrlog[i], i2c->icrlog[i]); printk("\n"); @@ -161,7 +176,7 @@ static void i2c_pxa_scream_blue_murder(struct pxa_i2c *i2c, const char *why) static inline int i2c_pxa_is_slavemode(struct pxa_i2c *i2c) { - return !(ICR & ICR_SCLE); + return !(readl(_ICR(i2c)) & ICR_SCLE); } static void i2c_pxa_abort(struct pxa_i2c *i2c) @@ -173,28 +188,29 @@ static void i2c_pxa_abort(struct pxa_i2c *i2c) return; } - while (time_before(jiffies, timeout) && (IBMR & 0x1) == 0) { - unsigned long icr = ICR; + while (time_before(jiffies, timeout) && (readl(_IBMR(i2c)) & 0x1) == 0) { + unsigned long icr = readl(_ICR(i2c)); icr &= ~ICR_START; icr |= ICR_ACKNAK | ICR_STOP | ICR_TB; - ICR = icr; + writel(icr, _ICR(i2c)); show_state(i2c); msleep(1); } - ICR &= ~(ICR_MA | ICR_START | ICR_STOP); + writel(readl(_ICR(i2c)) & ~(ICR_MA | ICR_START | ICR_STOP), + _ICR(i2c)); } static int i2c_pxa_wait_bus_not_busy(struct pxa_i2c *i2c) { int timeout = DEF_TIMEOUT; - while (timeout-- && ISR & (ISR_IBB | ISR_UB)) { - if ((ISR & ISR_SAD) != 0) + while (timeout-- && readl(_ISR(i2c)) & (ISR_IBB | ISR_UB)) { + if ((readl(_ISR(i2c)) & ISR_SAD) != 0) timeout += 4; msleep(2); @@ -214,9 +230,9 @@ static int i2c_pxa_wait_master(struct pxa_i2c *i2c) while (time_before(jiffies, timeout)) { if (i2c_debug > 1) dev_dbg(&i2c->adap.dev, "%s: %ld: ISR=%08x, ICR=%08x, IBMR=%02x\n", - __func__, (long)jiffies, ISR, ICR, IBMR); + __func__, (long)jiffies, readl(_ISR(i2c)), readl(_ICR(i2c)), readl(_IBMR(i2c))); - if (ISR & ISR_SAD) { + if (readl(_ISR(i2c)) & ISR_SAD) { if (i2c_debug > 0) dev_dbg(&i2c->adap.dev, "%s: Slave detected\n", __func__); goto out; @@ -226,7 +242,7 @@ static int i2c_pxa_wait_master(struct pxa_i2c *i2c) * quick check of the i2c lines themselves to ensure they've * gone high... */ - if ((ISR & (ISR_UB | ISR_IBB)) == 0 && IBMR == 3) { + if ((readl(_ISR(i2c)) & (ISR_UB | ISR_IBB)) == 0 && readl(_IBMR(i2c)) == 3) { if (i2c_debug > 0) dev_dbg(&i2c->adap.dev, "%s: done\n", __func__); return 1; @@ -246,7 +262,7 @@ static int i2c_pxa_set_master(struct pxa_i2c *i2c) if (i2c_debug) dev_dbg(&i2c->adap.dev, "setting to bus master\n"); - if ((ISR & (ISR_UB | ISR_IBB)) != 0) { + if ((readl(_ISR(i2c)) & (ISR_UB | ISR_IBB)) != 0) { dev_dbg(&i2c->adap.dev, "%s: unit is busy\n", __func__); if (!i2c_pxa_wait_master(i2c)) { dev_dbg(&i2c->adap.dev, "%s: error: unit busy\n", __func__); @@ -254,7 +270,7 @@ static int i2c_pxa_set_master(struct pxa_i2c *i2c) } } - ICR |= ICR_SCLE; + writel(readl(_ICR(i2c)) | ICR_SCLE, _ICR(i2c)); return 0; } @@ -270,11 +286,11 @@ static int i2c_pxa_wait_slave(struct pxa_i2c *i2c) while (time_before(jiffies, timeout)) { if (i2c_debug > 1) dev_dbg(&i2c->adap.dev, "%s: %ld: ISR=%08x, ICR=%08x, IBMR=%02x\n", - __func__, (long)jiffies, ISR, ICR, IBMR); + __func__, (long)jiffies, readl(_ISR(i2c)), readl(_ICR(i2c)), readl(_IBMR(i2c))); - if ((ISR & (ISR_UB|ISR_IBB)) == 0 || - (ISR & ISR_SAD) != 0 || - (ICR & ICR_SCLE) == 0) { + if ((readl(_ISR(i2c)) & (ISR_UB|ISR_IBB)) == 0 || + (readl(_ISR(i2c)) & ISR_SAD) != 0 || + (readl(_ICR(i2c)) & ICR_SCLE) == 0) { if (i2c_debug > 1) dev_dbg(&i2c->adap.dev, "%s: done\n", __func__); return 1; @@ -302,9 +318,9 @@ static void i2c_pxa_set_slave(struct pxa_i2c *i2c, int errcode) /* we need to wait for the stop condition to end */ /* if we where in stop, then clear... */ - if (ICR & ICR_STOP) { + if (readl(_ICR(i2c)) & ICR_STOP) { udelay(100); - ICR &= ~ICR_STOP; + writel(readl(_ICR(i2c)) & ~ICR_STOP, _ICR(i2c)); } if (!i2c_pxa_wait_slave(i2c)) { @@ -314,12 +330,12 @@ static void i2c_pxa_set_slave(struct pxa_i2c *i2c, int errcode) } } - ICR &= ~(ICR_STOP|ICR_ACKNAK|ICR_MA); - ICR &= ~ICR_SCLE; + writel(readl(_ICR(i2c)) & ~(ICR_STOP|ICR_ACKNAK|ICR_MA), _ICR(i2c)); + writel(readl(_ICR(i2c)) & ~ICR_SCLE, _ICR(i2c)); if (i2c_debug) { - dev_dbg(&i2c->adap.dev, "ICR now %08x, ISR %08x\n", ICR, ISR); - decode_ICR(ICR); + dev_dbg(&i2c->adap.dev, "ICR now %08x, ISR %08x\n", readl(_ICR(i2c)), readl(_ISR(i2c))); + decode_ICR(readl(_ICR(i2c))); } } #else @@ -334,24 +350,24 @@ static void i2c_pxa_reset(struct pxa_i2c *i2c) i2c_pxa_abort(i2c); /* reset according to 9.8 */ - ICR = ICR_UR; - ISR = I2C_ISR_INIT; - ICR &= ~ICR_UR; + writel(ICR_UR, _ICR(i2c)); + writel(I2C_ISR_INIT, _ISR(i2c)); + writel(readl(_ICR(i2c)) & ~ICR_UR, _ICR(i2c)); - ISAR = i2c->slave_addr; + writel(i2c->slave_addr, _ISAR(i2c)); /* set control register values */ - ICR = I2C_ICR_INIT; + writel(I2C_ICR_INIT, _ICR(i2c)); #ifdef CONFIG_I2C_PXA_SLAVE dev_info(&i2c->adap.dev, "Enabling slave mode\n"); - ICR |= ICR_SADIE | ICR_ALDIE | ICR_SSDIE; + writel(readl(_ICR(i2c)) | ICR_SADIE | ICR_ALDIE | ICR_SSDIE, _ICR(i2c)); #endif i2c_pxa_set_slave(i2c, 0); /* enable unit */ - ICR |= ICR_IUE; + writel(readl(_ICR(i2c)) | ICR_IUE, _ICR(i2c)); udelay(100); } @@ -371,19 +387,19 @@ static void i2c_pxa_slave_txempty(struct pxa_i2c *i2c, u32 isr) if (i2c->slave != NULL) ret = i2c->slave->read(i2c->slave->data); - IDBR = ret; - ICR |= ICR_TB; /* allow next byte */ + writel(ret, _IDBR(i2c)); + writel(readl(_ICR(i2c)) | ICR_TB, _ICR(i2c)); /* allow next byte */ } } static void i2c_pxa_slave_rxfull(struct pxa_i2c *i2c, u32 isr) { - unsigned int byte = IDBR; + unsigned int byte = readl(_IDBR(i2c)); if (i2c->slave != NULL) i2c->slave->write(i2c->slave->data, byte); - ICR |= ICR_TB; + writel(readl(_ICR(i2c)) | ICR_TB, _ICR(i2c)); } static void i2c_pxa_slave_start(struct pxa_i2c *i2c, u32 isr) @@ -403,13 +419,13 @@ static void i2c_pxa_slave_start(struct pxa_i2c *i2c, u32 isr) * start condition... if this happens, we'd better back off * and stop holding the poor thing up */ - ICR &= ~(ICR_START|ICR_STOP); - ICR |= ICR_TB; + writel(readl(_ICR(i2c)) & ~(ICR_START|ICR_STOP), _ICR(i2c)); + writel(readl(_ICR(i2c)) | ICR_TB, _ICR(i2c)); timeout = 0x10000; while (1) { - if ((IBMR & 2) == 2) + if ((readl(_IBMR(i2c)) & 2) == 2) break; timeout--; @@ -420,7 +436,7 @@ static void i2c_pxa_slave_start(struct pxa_i2c *i2c, u32 isr) } } - ICR &= ~ICR_SCLE; + writel(readl(_ICR(i2c)) & ~ICR_SCLE, _ICR(i2c)); } static void i2c_pxa_slave_stop(struct pxa_i2c *i2c) @@ -447,14 +463,14 @@ static void i2c_pxa_slave_txempty(struct pxa_i2c *i2c, u32 isr) if (isr & ISR_BED) { /* what should we do here? */ } else { - IDBR = 0; - ICR |= ICR_TB; + writel(0, _IDBR(i2c)); + writel(readl(_ICR(i2c)) | ICR_TB, _ICR(i2c)); } } static void i2c_pxa_slave_rxfull(struct pxa_i2c *i2c, u32 isr) { - ICR |= ICR_TB | ICR_ACKNAK; + writel(readl(_ICR(i2c)) | ICR_TB | ICR_ACKNAK, _ICR(i2c)); } static void i2c_pxa_slave_start(struct pxa_i2c *i2c, u32 isr) @@ -466,13 +482,13 @@ static void i2c_pxa_slave_start(struct pxa_i2c *i2c, u32 isr) * start condition... if this happens, we'd better back off * and stop holding the poor thing up */ - ICR &= ~(ICR_START|ICR_STOP); - ICR |= ICR_TB | ICR_ACKNAK; + writel(readl(_ICR(i2c)) & ~(ICR_START|ICR_STOP), _ICR(i2c)); + writel(readl(_ICR(i2c)) | ICR_TB | ICR_ACKNAK, _ICR(i2c)); timeout = 0x10000; while (1) { - if ((IBMR & 2) == 2) + if ((readl(_IBMR(i2c)) & 2) == 2) break; timeout--; @@ -483,7 +499,7 @@ static void i2c_pxa_slave_start(struct pxa_i2c *i2c, u32 isr) } } - ICR &= ~ICR_SCLE; + writel(readl(_ICR(i2c)) & ~ICR_SCLE, _ICR(i2c)); } static void i2c_pxa_slave_stop(struct pxa_i2c *i2c) @@ -514,13 +530,13 @@ static inline void i2c_pxa_start_message(struct pxa_i2c *i2c) /* * Step 1: target slave address into IDBR */ - IDBR = i2c_pxa_addr_byte(i2c->msg); + writel(i2c_pxa_addr_byte(i2c->msg), _IDBR(i2c)); /* * Step 2: initiate the write. */ - icr = ICR & ~(ICR_STOP | ICR_ALDIE); - ICR = icr | ICR_START | ICR_TB; + icr = readl(_ICR(i2c)) & ~(ICR_STOP | ICR_ALDIE); + writel(icr | ICR_START | ICR_TB, _ICR(i2c)); } /* @@ -594,7 +610,7 @@ static void i2c_pxa_master_complete(struct pxa_i2c *i2c, int ret) static void i2c_pxa_irq_txempty(struct pxa_i2c *i2c, u32 isr) { - u32 icr = ICR & ~(ICR_START|ICR_STOP|ICR_ACKNAK|ICR_TB); + u32 icr = readl(_ICR(i2c)) & ~(ICR_START|ICR_STOP|ICR_ACKNAK|ICR_TB); again: /* @@ -645,7 +661,7 @@ static void i2c_pxa_irq_txempty(struct pxa_i2c *i2c, u32 isr) /* * Write mode. Write the next data byte. */ - IDBR = i2c->msg->buf[i2c->msg_ptr++]; + writel(i2c->msg->buf[i2c->msg_ptr++], _IDBR(i2c)); icr |= ICR_ALDIE | ICR_TB; @@ -675,7 +691,7 @@ static void i2c_pxa_irq_txempty(struct pxa_i2c *i2c, u32 isr) /* * Write the next address. */ - IDBR = i2c_pxa_addr_byte(i2c->msg); + writel(i2c_pxa_addr_byte(i2c->msg), _IDBR(i2c)); /* * And trigger a repeated start, and send the byte. @@ -696,18 +712,18 @@ static void i2c_pxa_irq_txempty(struct pxa_i2c *i2c, u32 isr) i2c->icrlog[i2c->irqlogidx-1] = icr; - ICR = icr; + writel(icr, _ICR(i2c)); show_state(i2c); } static void i2c_pxa_irq_rxfull(struct pxa_i2c *i2c, u32 isr) { - u32 icr = ICR & ~(ICR_START|ICR_STOP|ICR_ACKNAK|ICR_TB); + u32 icr = readl(_ICR(i2c)) & ~(ICR_START|ICR_STOP|ICR_ACKNAK|ICR_TB); /* * Read the byte. */ - i2c->msg->buf[i2c->msg_ptr++] = IDBR; + i2c->msg->buf[i2c->msg_ptr++] = readl(_IDBR(i2c)); if (i2c->msg_ptr < i2c->msg->len) { /* @@ -724,17 +740,17 @@ static void i2c_pxa_irq_rxfull(struct pxa_i2c *i2c, u32 isr) i2c->icrlog[i2c->irqlogidx-1] = icr; - ICR = icr; + writel(icr, _ICR(i2c)); } static irqreturn_t i2c_pxa_handler(int this_irq, void *dev_id) { struct pxa_i2c *i2c = dev_id; - u32 isr = ISR; + u32 isr = readl(_ISR(i2c)); if (i2c_debug > 2 && 0) { dev_dbg(&i2c->adap.dev, "%s: ISR=%08x, ICR=%08x, IBMR=%02x\n", - __func__, isr, ICR, IBMR); + __func__, isr, readl(_ICR(i2c)), readl(_IBMR(i2c))); decode_ISR(isr); } @@ -746,7 +762,7 @@ static irqreturn_t i2c_pxa_handler(int this_irq, void *dev_id) /* * Always clear all pending IRQs. */ - ISR = isr & (ISR_SSD|ISR_ALD|ISR_ITE|ISR_IRF|ISR_SAD|ISR_BED); + writel(isr & (ISR_SSD|ISR_ALD|ISR_ITE|ISR_IRF|ISR_SAD|ISR_BED), _ISR(i2c)); if (isr & ISR_SAD) i2c_pxa_slave_start(i2c, isr); @@ -779,7 +795,7 @@ static int i2c_pxa_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num /* If the I2C controller is disabled we need to reset it (probably due to a suspend/resume destroying state). We do this here as we can then avoid worrying about resuming the controller before its users. */ - if (!(ICR & ICR_IUE)) + if (!(readl(_ICR(i2c)) & ICR_IUE)) i2c_pxa_reset(i2c); for (i = adap->retries; i >= 0; i--) { @@ -810,28 +826,53 @@ static const struct i2c_algorithm i2c_pxa_algorithm = { static struct pxa_i2c i2c_pxa = { .lock = SPIN_LOCK_UNLOCKED, - .wait = __WAIT_QUEUE_HEAD_INITIALIZER(i2c_pxa.wait), .adap = { .owner = THIS_MODULE, .algo = &i2c_pxa_algorithm, - .name = "pxa2xx-i2c", + .name = "pxa2xx-i2c.0", .retries = 5, }, }; +#define res_len(r) ((r)->end - (r)->start + 1) static int i2c_pxa_probe(struct platform_device *dev) { struct pxa_i2c *i2c = &i2c_pxa; + struct resource *res; #ifdef CONFIG_I2C_PXA_SLAVE struct i2c_pxa_platform_data *plat = dev->dev.platform_data; #endif int ret; + int irq; -#ifdef CONFIG_PXA27x - pxa_gpio_mode(GPIO117_I2CSCL_MD); - pxa_gpio_mode(GPIO118_I2CSDA_MD); - udelay(100); -#endif + res = platform_get_resource(dev, IORESOURCE_MEM, 0); + irq = platform_get_irq(dev, 0); + if (res == NULL || irq < 0) + return -ENODEV; + + if (!request_mem_region(res->start, res_len(res), res->name)) + return -ENOMEM; + + i2c = kmalloc(sizeof(struct pxa_i2c), GFP_KERNEL); + if (!i2c) { + ret = -ENOMEM; + goto emalloc; + } + + memcpy(i2c, &i2c_pxa, sizeof(struct pxa_i2c)); + init_waitqueue_head(&i2c->wait); + i2c->adap.name[strlen(i2c->adap.name) - 1] = '0' + dev->id % 10; + + i2c->reg_base = ioremap(res->start, res_len(res)); + if (!i2c->reg_base) { + ret = -EIO; + goto eremap; + } + + i2c->iobase = res->start; + i2c->iosize = res_len(res); + + i2c->irq = irq; i2c->slave_addr = I2C_PXA_SLAVE_ADDR; @@ -842,11 +883,28 @@ static int i2c_pxa_probe(struct platform_device *dev) } #endif - pxa_set_cken(CKEN14_I2C, 1); - ret = request_irq(IRQ_I2C, i2c_pxa_handler, IRQF_DISABLED, - "pxa2xx-i2c", i2c); + switch (dev->id) { + case 0: +#ifdef CONFIG_PXA27x + pxa_gpio_mode(GPIO117_I2CSCL_MD); + pxa_gpio_mode(GPIO118_I2CSDA_MD); +#endif + pxa_set_cken(CKEN14_I2C, 1); + break; +#ifdef CONFIG_PXA27x + case 1: + local_irq_disable(); + PCFR |= PCFR_PI2CEN; + local_irq_enable(); + pxa_set_cken(CKEN15_PWRI2C, 1); +#endif + } + + ret = request_irq(irq, i2c_pxa_handler, IRQF_DISABLED, + i2c->adap.name, i2c); if (ret) - goto out; + goto ereqirq; + i2c_pxa_reset(i2c); @@ -856,7 +914,7 @@ static int i2c_pxa_probe(struct platform_device *dev) ret = i2c_add_adapter(&i2c->adap); if (ret < 0) { printk(KERN_INFO "I2C: Failed to add bus\n"); - goto err_irq; + goto eadapt; } platform_set_drvdata(dev, i2c); @@ -870,9 +928,25 @@ static int i2c_pxa_probe(struct platform_device *dev) #endif return 0; - err_irq: - free_irq(IRQ_I2C, i2c); - out: +eadapt: + free_irq(irq, i2c); +ereqirq: + switch (dev->id) { + case 0: + pxa_set_cken(CKEN14_I2C, 0); + break; +#ifdef CONFIG_PXA27x + case 1: + pxa_set_cken(CKEN15_PWRI2C, 0); + local_irq_disable(); + PCFR &= ~PCFR_PI2CEN; + local_irq_enable(); +#endif + } +eremap: + kfree(i2c); +emalloc: + release_mem_region(res->start, res_len(res)); return ret; } @@ -883,8 +957,21 @@ static int i2c_pxa_remove(struct platform_device *dev) platform_set_drvdata(dev, NULL); i2c_del_adapter(&i2c->adap); - free_irq(IRQ_I2C, i2c); - pxa_set_cken(CKEN14_I2C, 0); + free_irq(i2c->irq, i2c); + switch (dev->id) { + case 0: + pxa_set_cken(CKEN14_I2C, 0); + break; +#ifdef CONFIG_PXA27x + case 1: + pxa_set_cken(CKEN15_PWRI2C, 0); + local_irq_disable(); + PCFR &= ~PCFR_PI2CEN; + local_irq_enable(); +#endif + } + release_mem_region(i2c->iobase, i2c->iosize); + kfree(i2c); return 0; } -- cgit v1.2.3 From 45cf5eef4fa8bcd8d3aca3c2a0703d791c9ea56c Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Mon, 5 Feb 2007 22:37:07 +0100 Subject: [ARM] 4136/1: Allow PXA2xx's clock source to be used Commit c80204e5d67d1452ac0b761d980f1651dc2c66dc apparently missed this. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6783c2e5512d..f7fa24b96eaa 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -280,6 +280,7 @@ config ARCH_PXA bool "PXA2xx-based" depends on MMU select ARCH_MTD_XIP + select GENERIC_TIME help Support for Intel's PXA2XX processor line. -- cgit v1.2.3 From 51dd249eff28924f838a72a50c417b2089e0f6a9 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sun, 4 Feb 2007 22:45:33 +0100 Subject: [ARM] 4120/1: ep93xx: make clock init an arch_initcall() Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mach-ep93xx/clock.c | 6 +++++- arch/arm/mach-ep93xx/core.c | 2 -- include/asm-arm/arch-ep93xx/platform.h | 1 - 3 files changed, 5 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c index 08ad782c1649..f174d1a3b11c 100644 --- a/arch/arm/mach-ep93xx/clock.c +++ b/arch/arm/mach-ep93xx/clock.c @@ -13,6 +13,7 @@ #include #include #include +#include #include #include #include @@ -124,7 +125,7 @@ static unsigned long calc_pll_rate(u32 config_word) return (unsigned long)rate; } -void ep93xx_clock_init(void) +static int __init ep93xx_clock_init(void) { u32 value; @@ -153,4 +154,7 @@ void ep93xx_clock_init(void) printk(KERN_INFO "ep93xx: FCLK %ld MHz, HCLK %ld MHz, PCLK %ld MHz\n", clk_f.rate / 1000000, clk_h.rate / 1000000, clk_p.rate / 1000000); + + return 0; } +arch_initcall(ep93xx_clock_init); diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index 6b26346191c0..913ea4328b2f 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -461,8 +461,6 @@ void __init ep93xx_init_devices(void) { unsigned int v; - ep93xx_clock_init(); - /* * Disallow access to MaverickCrunch initially. */ diff --git a/include/asm-arm/arch-ep93xx/platform.h b/include/asm-arm/arch-ep93xx/platform.h index b4a8deb8bdef..44eccec2cba4 100644 --- a/include/asm-arm/arch-ep93xx/platform.h +++ b/include/asm-arm/arch-ep93xx/platform.h @@ -8,7 +8,6 @@ void ep93xx_map_io(void); void ep93xx_init_irq(void); void ep93xx_init_time(unsigned long); void ep93xx_init_devices(void); -void ep93xx_clock_init(void); extern struct sys_timer ep93xx_timer; struct ep93xx_eth_data -- cgit v1.2.3 From fac105d05e4b410c586de55dfbf34f40a95f6977 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 5 Feb 2007 00:35:37 +0100 Subject: [ARM] 4121/1: ep93xx: move setting of HWCAP_CRUNCH Move the setting of HWCAP_CRUNCH to kernel/crunch.c, where it belongs. Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/kernel/crunch.c | 1 + arch/arm/mach-ep93xx/core.c | 4 ---- 2 files changed, 1 insertion(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/crunch.c b/arch/arm/kernel/crunch.c index cec83783206e..627d79414c9d 100644 --- a/arch/arm/kernel/crunch.c +++ b/arch/arm/kernel/crunch.c @@ -75,6 +75,7 @@ static struct notifier_block crunch_notifier_block = { static int __init crunch_init(void) { thread_register_notifier(&crunch_notifier_block); + elf_hwcap |= HWCAP_CRUNCH; return 0; } diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index 913ea4328b2f..5d2739abd960 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -475,8 +475,4 @@ void __init ep93xx_init_devices(void) platform_device_register(&ep93xx_rtc_device); platform_device_register(&ep93xx_ohci_device); - -#ifdef CONFIG_CRUNCH - elf_hwcap |= HWCAP_CRUNCH; -#endif } -- cgit v1.2.3 From 4932e397be71370b95f555f87d3b424d2b5ca57b Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 5 Feb 2007 00:38:48 +0100 Subject: [ARM] 4122/1: ep93xx: add support for GPIO port F interrupts Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mach-ep93xx/core.c | 90 +++++++++++++++++++++---------- include/asm-arm/arch-ep93xx/ep93xx-regs.h | 5 ++ include/asm-arm/arch-ep93xx/irqs.h | 8 ++- 3 files changed, 73 insertions(+), 30 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index 5d2739abd960..94bba0b87e36 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -152,22 +152,29 @@ struct sys_timer ep93xx_timer = { /************************************************************************* * GPIO handling for EP93xx *************************************************************************/ -static unsigned char gpio_int_enable[2]; -static unsigned char gpio_int_type1[2]; -static unsigned char gpio_int_type2[2]; +static unsigned char gpio_int_enable[3]; +static unsigned char gpio_int_type1[3]; +static unsigned char gpio_int_type2[3]; -static void update_gpio_ab_int_params(int port) +static void update_gpio_int_params(int abf) { - if (port == 0) { + if (abf == 0) { __raw_writeb(0, EP93XX_GPIO_A_INT_ENABLE); __raw_writeb(gpio_int_type2[0], EP93XX_GPIO_A_INT_TYPE2); __raw_writeb(gpio_int_type1[0], EP93XX_GPIO_A_INT_TYPE1); __raw_writeb(gpio_int_enable[0], EP93XX_GPIO_A_INT_ENABLE); - } else if (port == 1) { + } else if (abf == 1) { __raw_writeb(0, EP93XX_GPIO_B_INT_ENABLE); __raw_writeb(gpio_int_type2[1], EP93XX_GPIO_B_INT_TYPE2); __raw_writeb(gpio_int_type1[1], EP93XX_GPIO_B_INT_TYPE1); __raw_writeb(gpio_int_enable[1], EP93XX_GPIO_B_INT_ENABLE); + } else if (abf == 2) { + __raw_writeb(0, EP93XX_GPIO_F_INT_ENABLE); + __raw_writeb(gpio_int_type2[2], EP93XX_GPIO_F_INT_TYPE2); + __raw_writeb(gpio_int_type1[2], EP93XX_GPIO_F_INT_TYPE1); + __raw_writeb(gpio_int_enable[2], EP93XX_GPIO_F_INT_ENABLE); + } else { + BUG(); } } @@ -192,8 +199,13 @@ void gpio_line_config(int line, int direction) local_irq_save(flags); if (direction == GPIO_OUT) { if (line >= 0 && line < 16) { + /* Port A/B. */ gpio_int_enable[line >> 3] &= ~(1 << (line & 7)); - update_gpio_ab_int_params(line >> 3); + update_gpio_int_params(line >> 3); + } else if (line >= 40 && line < 48) { + /* Port F. */ + gpio_int_enable[2] &= ~(1 << (line & 7)); + update_gpio_int_params(2); } v = __raw_readb(data_direction_register); @@ -244,8 +256,7 @@ EXPORT_SYMBOL(gpio_line_set); /************************************************************************* * EP93xx IRQ handling *************************************************************************/ -static void ep93xx_gpio_ab_irq_handler(unsigned int irq, - struct irq_desc *desc) +static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc) { unsigned char status; int i; @@ -267,37 +278,46 @@ static void ep93xx_gpio_ab_irq_handler(unsigned int irq, } } -static void ep93xx_gpio_ab_irq_mask_ack(unsigned int irq) +static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + int gpio_irq = IRQ_EP93XX_GPIO(16) + (((irq + 1) & 7) ^ 4); + + desc_handle_irq(gpio_irq, irq_desc + gpio_irq); +} + +static void ep93xx_gpio_irq_mask_ack(unsigned int irq) { int line = irq - IRQ_EP93XX_GPIO(0); int port = line >> 3; gpio_int_enable[port] &= ~(1 << (line & 7)); - update_gpio_ab_int_params(port); + update_gpio_int_params(port); - if (line >> 3) { - __raw_writel(1 << (line & 7), EP93XX_GPIO_B_INT_ACK); - } else { + if (port == 0) { __raw_writel(1 << (line & 7), EP93XX_GPIO_A_INT_ACK); + } else if (port == 1) { + __raw_writel(1 << (line & 7), EP93XX_GPIO_B_INT_ACK); + } else if (port == 2) { + __raw_writel(1 << (line & 7), EP93XX_GPIO_F_INT_ACK); } } -static void ep93xx_gpio_ab_irq_mask(unsigned int irq) +static void ep93xx_gpio_irq_mask(unsigned int irq) { int line = irq - IRQ_EP93XX_GPIO(0); int port = line >> 3; gpio_int_enable[port] &= ~(1 << (line & 7)); - update_gpio_ab_int_params(port); + update_gpio_int_params(port); } -static void ep93xx_gpio_ab_irq_unmask(unsigned int irq) +static void ep93xx_gpio_irq_unmask(unsigned int irq) { int line = irq - IRQ_EP93XX_GPIO(0); int port = line >> 3; gpio_int_enable[port] |= 1 << (line & 7); - update_gpio_ab_int_params(port); + update_gpio_int_params(port); } @@ -306,13 +326,17 @@ static void ep93xx_gpio_ab_irq_unmask(unsigned int irq) * edge (1) triggered, while gpio_int_type2 controls whether it * triggers on low/falling (0) or high/rising (1). */ -static int ep93xx_gpio_ab_irq_type(unsigned int irq, unsigned int type) +static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type) { int port; int line; line = irq - IRQ_EP93XX_GPIO(0); - gpio_line_config(line, GPIO_IN); + if (line >= 0 && line < 16) { + gpio_line_config(line, GPIO_IN); + } else { + gpio_line_config(EP93XX_GPIO_LINE_F(line), GPIO_IN); + } port = line >> 3; line &= 7; @@ -330,16 +354,17 @@ static int ep93xx_gpio_ab_irq_type(unsigned int irq, unsigned int type) gpio_int_type1[port] &= ~(1 << line); gpio_int_type2[port] &= ~(1 << line); } - update_gpio_ab_int_params(port); + update_gpio_int_params(port); return 0; } -static struct irq_chip ep93xx_gpio_ab_irq_chip = { - .ack = ep93xx_gpio_ab_irq_mask_ack, - .mask = ep93xx_gpio_ab_irq_mask, - .unmask = ep93xx_gpio_ab_irq_unmask, - .set_type = ep93xx_gpio_ab_irq_type, +static struct irq_chip ep93xx_gpio_irq_chip = { + .name = "GPIO", + .ack = ep93xx_gpio_irq_mask_ack, + .mask = ep93xx_gpio_irq_mask, + .unmask = ep93xx_gpio_irq_unmask, + .set_type = ep93xx_gpio_irq_type, }; @@ -350,12 +375,21 @@ void __init ep93xx_init_irq(void) vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK); vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK); - for (irq = IRQ_EP93XX_GPIO(0) ; irq <= IRQ_EP93XX_GPIO(15); irq++) { - set_irq_chip(irq, &ep93xx_gpio_ab_irq_chip); + for (irq = IRQ_EP93XX_GPIO(0); irq <= IRQ_EP93XX_GPIO(23); irq++) { + set_irq_chip(irq, &ep93xx_gpio_irq_chip); set_irq_handler(irq, handle_level_irq); set_irq_flags(irq, IRQF_VALID); } + set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler); + set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler); } diff --git a/include/asm-arm/arch-ep93xx/ep93xx-regs.h b/include/asm-arm/arch-ep93xx/ep93xx-regs.h index 593f562f85c3..625c6f0abc03 100644 --- a/include/asm-arm/arch-ep93xx/ep93xx-regs.h +++ b/include/asm-arm/arch-ep93xx/ep93xx-regs.h @@ -73,6 +73,11 @@ #define EP93XX_GPIO_BASE (EP93XX_APB_VIRT_BASE + 0x00040000) #define EP93XX_GPIO_REG(x) (EP93XX_GPIO_BASE + (x)) +#define EP93XX_GPIO_F_INT_TYPE1 EP93XX_GPIO_REG(0x4c) +#define EP93XX_GPIO_F_INT_TYPE2 EP93XX_GPIO_REG(0x50) +#define EP93XX_GPIO_F_INT_ACK EP93XX_GPIO_REG(0x54) +#define EP93XX_GPIO_F_INT_ENABLE EP93XX_GPIO_REG(0x58) +#define EP93XX_GPIO_F_INT_STATUS EP93XX_GPIO_REG(0x5c) #define EP93XX_GPIO_A_INT_TYPE1 EP93XX_GPIO_REG(0x90) #define EP93XX_GPIO_A_INT_TYPE2 EP93XX_GPIO_REG(0x94) #define EP93XX_GPIO_A_INT_ACK EP93XX_GPIO_REG(0x98) diff --git a/include/asm-arm/arch-ep93xx/irqs.h b/include/asm-arm/arch-ep93xx/irqs.h index ae532e304bf1..2a8c63638c5e 100644 --- a/include/asm-arm/arch-ep93xx/irqs.h +++ b/include/asm-arm/arch-ep93xx/irqs.h @@ -67,9 +67,13 @@ #define IRQ_EP93XX_SAI 60 #define EP93XX_VIC2_VALID_IRQ_MASK 0x1fffffff -#define IRQ_EP93XX_GPIO(x) (64 + (x)) +/* + * Map GPIO A0..A7 to irq 64..71, B0..B7 to 72..79, and + * F0..F7 to 80..87. + */ +#define IRQ_EP93XX_GPIO(x) (64 + (((x) + (((x) >> 2) & 8)) & 0x1f)) -#define NR_EP93XX_IRQS IRQ_EP93XX_GPIO(16) +#define NR_EP93XX_IRQS (64 + 24) #define EP93XX_BOARD_IRQ(x) (NR_EP93XX_IRQS + (x)) #define EP93XX_BOARD_IRQS 32 -- cgit v1.2.3 From 850b42933e70c19c7765dd7fad15cb7ad3955b65 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 5 Feb 2007 00:55:27 +0100 Subject: [ARM] 4123/1: xsc3: general cleanup This patch cleans up proc-xsc3: - Correct a number of typos. - Fix up indentation in a number of places. - Change references to the various caches to be more clear about whether we're talking about the L1 D, the L1 I or the unified L2 cache. - Rename "drain write buffer" to "data write barrier", the official name used in the Manzano manual. - Change the xsc3 cpu name from "XScale-Core3" to "XScale-V3 based processor". Also, since a previously merged patch implements proper support for using a MAC or iWMMXt coprocessor on xsc3 platforms, we no longer need to enable access to CP0 on boot. Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mm/proc-xsc3.S | 151 ++++++++++++++++++++++++------------------------ 1 file changed, 75 insertions(+), 76 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S index 94a58455f346..d95921a2ab99 100644 --- a/arch/arm/mm/proc-xsc3.S +++ b/arch/arm/mm/proc-xsc3.S @@ -5,23 +5,23 @@ * Current Maintainer: Lennert Buytenhek * * Copyright 2004 (C) Intel Corp. - * Copyright 2005 (c) MontaVista Software, Inc. + * Copyright 2005 (C) MontaVista Software, Inc. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * - * MMU functions for the Intel XScale3 Core (XSC3). The XSC3 core is an - * extension to Intel's original XScale core that adds the following + * MMU functions for the Intel XScale3 Core (XSC3). The XSC3 core is + * an extension to Intel's original XScale core that adds the following * features: * * - ARMv6 Supersections * - Low Locality Reference pages (replaces mini-cache) * - 36-bit addressing * - L2 cache - * - Cache-coherency if chipset supports it + * - Cache coherency if chipset supports it * - * Based on orignal XScale code by Nicolas Pitre + * Based on original XScale code by Nicolas Pitre. */ #include @@ -42,12 +42,12 @@ #define MAX_AREA_SIZE 32768 /* - * The cache line size of the I and D cache. + * The cache line size of the L1 I, L1 D and unified L2 cache. */ #define CACHELINESIZE 32 /* - * The size of the data cache. + * The size of the L1 D cache. */ #define CACHESIZE 32768 @@ -57,9 +57,9 @@ #define L2_CACHE_ENABLE 1 /* - * This macro is used to wait for a CP15 write and is needed - * when we have to ensure that the last operation to the co-pro - * was completed before continuing with operation. + * This macro is used to wait for a CP15 write and is needed when we + * have to ensure that the last operation to the coprocessor was + * completed before continuing with operation. */ .macro cpwait_ret, lr, rd mrc p15, 0, \rd, c2, c0, 0 @ arbitrary read of cp15 @@ -68,13 +68,13 @@ .endm /* - * This macro cleans & invalidates the entire xsc3 dcache by set & way. + * This macro cleans and invalidates the entire L1 D cache. */ .macro clean_d_cache rd, rs mov \rd, #0x1f00 orr \rd, \rd, #0x00e0 -1: mcr p15, 0, \rd, c7, c14, 2 @ clean/inv set/way +1: mcr p15, 0, \rd, c7, c14, 2 @ clean/invalidate L1 D line adds \rd, \rd, #0x40000000 bcc 1b subs \rd, \rd, #0x20 @@ -119,15 +119,15 @@ ENTRY(cpu_xsc3_reset) mov r1, #PSR_F_BIT|PSR_I_BIT|SVC_MODE msr cpsr_c, r1 @ reset CPSR mrc p15, 0, r1, c1, c0, 0 @ ctrl register - bic r1, r1, #0x0086 @ ........B....CA. bic r1, r1, #0x3900 @ ..VIZ..S........ + bic r1, r1, #0x0086 @ ........B....CA. mcr p15, 0, r1, c1, c0, 0 @ ctrl register - mcr p15, 0, ip, c7, c7, 0 @ invalidate I,D caches & BTB + mcr p15, 0, ip, c7, c7, 0 @ invalidate L1 caches and BTB bic r1, r1, #0x0001 @ ...............M mcr p15, 0, r1, c1, c0, 0 @ ctrl register @ CAUTION: MMU turned off from this point. We count on the pipeline @ already containing those two last instructions to survive. - mcr p15, 0, ip, c8, c7, 0 @ invalidate I & D TLBs + mcr p15, 0, ip, c8, c7, 0 @ invalidate I and D TLBs mov pc, r0 /* @@ -139,14 +139,12 @@ ENTRY(cpu_xsc3_reset) * * XScale supports clock switching, but using idle mode support * allows external hardware to react to system state changes. - - MMG: Come back to this one. */ .align 5 ENTRY(cpu_xsc3_do_idle) mov r0, #1 - mcr p14, 0, r0, c7, c0, 0 @ Go to IDLE + mcr p14, 0, r0, c7, c0, 0 @ go to idle mov pc, lr /* ================================= CACHE ================================ */ @@ -171,9 +169,9 @@ ENTRY(xsc3_flush_kern_cache_all) __flush_whole_cache: clean_d_cache r0, r1 tst r2, #VM_EXEC - mcrne p15, 0, ip, c7, c5, 0 @ Invalidate I cache & BTB - mcrne p15, 0, ip, c7, c10, 4 @ Drain Write Buffer - mcrne p15, 0, ip, c7, c5, 4 @ Prefetch Flush + mcrne p15, 0, ip, c7, c5, 0 @ invalidate L1 I cache and BTB + mcrne p15, 0, ip, c7, c10, 4 @ data write barrier + mcrne p15, 0, ip, c7, c5, 4 @ prefetch flush mov pc, lr /* @@ -194,21 +192,21 @@ ENTRY(xsc3_flush_user_cache_range) bhs __flush_whole_cache 1: tst r2, #VM_EXEC - mcrne p15, 0, r0, c7, c5, 1 @ Invalidate I cache line - mcr p15, 0, r0, c7, c14, 1 @ Clean/invalidate D cache line + mcrne p15, 0, r0, c7, c5, 1 @ invalidate L1 I line + mcr p15, 0, r0, c7, c14, 1 @ clean/invalidate L1 D line add r0, r0, #CACHELINESIZE cmp r0, r1 blo 1b tst r2, #VM_EXEC - mcrne p15, 0, ip, c7, c5, 6 @ Invalidate BTB - mcrne p15, 0, ip, c7, c10, 4 @ Drain Write Buffer - mcrne p15, 0, ip, c7, c5, 4 @ Prefetch Flush + mcrne p15, 0, ip, c7, c5, 6 @ invalidate BTB + mcrne p15, 0, ip, c7, c10, 4 @ data write barrier + mcrne p15, 0, ip, c7, c5, 4 @ prefetch flush mov pc, lr /* * coherent_kern_range(start, end) * - * Ensure coherency between the Icache and the Dcache in the + * Ensure coherency between the I cache and the D cache in the * region described by start. If you have non-snooping * Harvard caches, you need to implement this function. * @@ -222,34 +220,34 @@ ENTRY(xsc3_coherent_kern_range) /* FALLTHROUGH */ ENTRY(xsc3_coherent_user_range) bic r0, r0, #CACHELINESIZE - 1 -1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry +1: mcr p15, 0, r0, c7, c10, 1 @ clean L1 D line add r0, r0, #CACHELINESIZE cmp r0, r1 blo 1b mov r0, #0 - mcr p15, 0, r0, c7, c5, 0 @ Invalidate I cache & BTB - mcr p15, 0, r0, c7, c10, 4 @ Drain Write Buffer - mcr p15, 0, r0, c7, c5, 4 @ Prefetch Flush + mcr p15, 0, r0, c7, c5, 0 @ invalidate L1 I cache and BTB + mcr p15, 0, r0, c7, c10, 4 @ data write barrier + mcr p15, 0, r0, c7, c5, 4 @ prefetch flush mov pc, lr /* * flush_kern_dcache_page(void *page) * * Ensure no D cache aliasing occurs, either with itself or - * the I cache + * the I cache. * * - addr - page aligned address */ ENTRY(xsc3_flush_kern_dcache_page) add r1, r0, #PAGE_SZ -1: mcr p15, 0, r0, c7, c14, 1 @ Clean/Invalidate D Cache line +1: mcr p15, 0, r0, c7, c14, 1 @ clean/invalidate L1 D line add r0, r0, #CACHELINESIZE cmp r0, r1 blo 1b mov r0, #0 - mcr p15, 0, r0, c7, c5, 0 @ Invalidate I cache & BTB - mcr p15, 0, r0, c7, c10, 4 @ Drain Write Buffer - mcr p15, 0, r0, c7, c5, 4 @ Prefetch Flush + mcr p15, 0, r0, c7, c5, 0 @ invalidate L1 I cache and BTB + mcr p15, 0, r0, c7, c10, 4 @ data write barrier + mcr p15, 0, r0, c7, c5, 4 @ prefetch flush mov pc, lr /* @@ -266,17 +264,17 @@ ENTRY(xsc3_flush_kern_dcache_page) ENTRY(xsc3_dma_inv_range) tst r0, #CACHELINESIZE - 1 bic r0, r0, #CACHELINESIZE - 1 - mcrne p15, 0, r0, c7, c10, 1 @ clean L1 D entry - mcrne p15, 1, r0, c7, c11, 1 @ clean L2 D entry + mcrne p15, 0, r0, c7, c10, 1 @ clean L1 D line + mcrne p15, 1, r0, c7, c11, 1 @ clean L2 line tst r1, #CACHELINESIZE - 1 - mcrne p15, 0, r1, c7, c10, 1 @ clean L1 D entry - mcrne p15, 1, r1, c7, c11, 1 @ clean L2 D entry -1: mcr p15, 0, r0, c7, c6, 1 @ invalidate L1 D entry - mcr p15, 1, r0, c7, c7, 1 @ Invalidate L2 D cache line + mcrne p15, 0, r1, c7, c10, 1 @ clean L1 D line + mcrne p15, 1, r1, c7, c11, 1 @ clean L2 line +1: mcr p15, 0, r0, c7, c6, 1 @ invalidate L1 D line + mcr p15, 1, r0, c7, c7, 1 @ invalidate L2 line add r0, r0, #CACHELINESIZE cmp r0, r1 blo 1b - mcr p15, 0, r0, c7, c10, 4 @ Drain Write Buffer + mcr p15, 0, r0, c7, c10, 4 @ data write barrier mov pc, lr /* @@ -289,12 +287,12 @@ ENTRY(xsc3_dma_inv_range) */ ENTRY(xsc3_dma_clean_range) bic r0, r0, #CACHELINESIZE - 1 -1: mcr p15, 0, r0, c7, c10, 1 @ clean L1 D entry - mcr p15, 1, r0, c7, c11, 1 @ clean L2 D entry +1: mcr p15, 0, r0, c7, c10, 1 @ clean L1 D line + mcr p15, 1, r0, c7, c11, 1 @ clean L2 line add r0, r0, #CACHELINESIZE cmp r0, r1 blo 1b - mcr p15, 0, r0, c7, c10, 4 @ Drain Write Buffer + mcr p15, 0, r0, c7, c10, 4 @ data write barrier mov pc, lr /* @@ -307,13 +305,13 @@ ENTRY(xsc3_dma_clean_range) */ ENTRY(xsc3_dma_flush_range) bic r0, r0, #CACHELINESIZE - 1 -1: mcr p15, 0, r0, c7, c14, 1 @ Clean/invalidate L1 D cache line - mcr p15, 1, r0, c7, c11, 1 @ Clean L2 D cache line - mcr p15, 1, r0, c7, c7, 1 @ Invalidate L2 D cache line +1: mcr p15, 0, r0, c7, c14, 1 @ clean/invalidate L1 D line + mcr p15, 1, r0, c7, c11, 1 @ clean L2 line + mcr p15, 1, r0, c7, c7, 1 @ invalidate L2 line add r0, r0, #CACHELINESIZE cmp r0, r1 blo 1b - mcr p15, 0, r0, c7, c10, 4 @ Drain Write Buffer + mcr p15, 0, r0, c7, c10, 4 @ data write barrier mov pc, lr ENTRY(xsc3_cache_fns) @@ -328,7 +326,7 @@ ENTRY(xsc3_cache_fns) .long xsc3_dma_flush_range ENTRY(cpu_xsc3_dcache_clean_area) -1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry +1: mcr p15, 0, r0, c7, c10, 1 @ clean L1 D line add r0, r0, #CACHELINESIZE subs r1, r1, #CACHELINESIZE bhi 1b @@ -346,14 +344,14 @@ ENTRY(cpu_xsc3_dcache_clean_area) .align 5 ENTRY(cpu_xsc3_switch_mm) clean_d_cache r1, r2 - mcr p15, 0, ip, c7, c5, 0 @ Invalidate I cache & BTB - mcr p15, 0, ip, c7, c10, 4 @ Drain Write Buffer - mcr p15, 0, ip, c7, c5, 4 @ Prefetch Flush + mcr p15, 0, ip, c7, c5, 0 @ invalidate L1 I cache and BTB + mcr p15, 0, ip, c7, c10, 4 @ data write barrier + mcr p15, 0, ip, c7, c5, 4 @ prefetch flush #ifdef L2_CACHE_ENABLE orr r0, r0, #0x18 @ cache the page table in L2 #endif mcr p15, 0, r0, c2, c0, 0 @ load page table pointer - mcr p15, 0, ip, c8, c7, 0 @ invalidate I & D TLBs + mcr p15, 0, ip, c8, c7, 0 @ invalidate I and D TLBs cpwait_ret lr, ip /* @@ -366,34 +364,34 @@ ENTRY(cpu_xsc3_switch_mm) ENTRY(cpu_xsc3_set_pte_ext) str r1, [r0], #-2048 @ linux version - bic r2, r1, #0xff0 @ Keep C, B bits + bic r2, r1, #0xff0 @ keep C, B bits orr r2, r2, #PTE_TYPE_EXT @ extended page - tst r1, #L_PTE_SHARED @ Shared? + tst r1, #L_PTE_SHARED @ shared? orrne r2, r2, #0x200 eor r3, r1, #L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_WRITE | L_PTE_DIRTY - tst r3, #L_PTE_USER @ User? + tst r3, #L_PTE_USER @ user? orrne r2, r2, #PTE_EXT_AP_URO_SRW @ yes -> user r/o, system r/w - tst r3, #L_PTE_WRITE | L_PTE_DIRTY @ Write and Dirty? + tst r3, #L_PTE_WRITE | L_PTE_DIRTY @ write and dirty? orreq r2, r2, #PTE_EXT_AP_UNO_SRW @ yes -> user n/a, system r/w @ combined with user -> user r/w #if L2_CACHE_ENABLE - @ If its cacheable it needs to be in L2 also. + @ If it's cacheable, it needs to be in L2 also. eor ip, r1, #L_PTE_CACHEABLE tst ip, #L_PTE_CACHEABLE orreq r2, r2, #PTE_EXT_TEX(0x5) #endif - tst r3, #L_PTE_PRESENT | L_PTE_YOUNG @ Present and Young? + tst r3, #L_PTE_PRESENT | L_PTE_YOUNG @ present and young? movne r2, #0 @ no -> fault str r2, [r0] @ hardware version mov ip, #0 - mcr p15, 0, r0, c7, c10, 1 @ Clean D cache line mcr - mcr p15, 0, ip, c7, c10, 4 @ Drain Write Buffer + mcr p15, 0, r0, c7, c10, 1 @ clean L1 D line + mcr p15, 0, ip, c7, c10, 4 @ data write barrier mov pc, lr .ltorg @@ -406,17 +404,18 @@ ENTRY(cpu_xsc3_set_pte_ext) __xsc3_setup: mov r0, #PSR_F_BIT|PSR_I_BIT|SVC_MODE msr cpsr_c, r0 - mcr p15, 0, ip, c7, c7, 0 @ invalidate I, D caches & BTB - mcr p15, 0, ip, c7, c10, 4 @ Drain Write Buffer - mcr p15, 0, ip, c7, c5, 4 @ Prefetch Flush - mcr p15, 0, ip, c8, c7, 0 @ invalidate I, D TLBs + mcr p15, 0, ip, c7, c7, 0 @ invalidate L1 caches and BTB + mcr p15, 0, ip, c7, c10, 4 @ data write barrier + mcr p15, 0, ip, c7, c5, 4 @ prefetch flush + mcr p15, 0, ip, c8, c7, 0 @ invalidate I and D TLBs #if L2_CACHE_ENABLE orr r4, r4, #0x18 @ cache the page table in L2 #endif mcr p15, 0, r4, c2, c0, 0 @ load page table pointer - mov r0, #1 @ Allow access to CP0 and CP13 - orr r0, r0, #1 << 13 @ Its undefined whether this - mcr p15, 0, r0, c15, c1, 0 @ affects USR or SVC modes + + mov r0, #0 @ don't allow CP access + mcr p15, 0, r0, c15, c1, 0 @ write CP access register + mrc p15, 0, r0, c1, c0, 1 @ get auxiliary control reg and r0, r0, #2 @ preserve bit P bit setting #if L2_CACHE_ENABLE @@ -427,9 +426,9 @@ __xsc3_setup: adr r5, xsc3_crval ldmia r5, {r5, r6} mrc p15, 0, r0, c1, c0, 0 @ get control register - bic r0, r0, r5 @ .... .... .... ..A. - orr r0, r0, r6 @ .... .... .... .C.M - orr r0, r0, #0x00000800 @ ..VI Z..S .... .... + bic r0, r0, r5 @ ..V. ..R. .... ..A. + orr r0, r0, r6 @ ..VI Z..S .... .C.M (mmu) + @ ...I Z..S .... .... (uc) #if L2_CACHE_ENABLE orr r0, r0, #0x04000000 @ L2 enable #endif @@ -439,7 +438,7 @@ __xsc3_setup: .type xsc3_crval, #object xsc3_crval: - crval clear=0x04003b02, mmuset=0x00003105, ucset=0x00001100 + crval clear=0x04002202, mmuset=0x00003905, ucset=0x00001900 __INITDATA @@ -474,7 +473,7 @@ cpu_elf_name: .type cpu_xsc3_name, #object cpu_xsc3_name: - .asciz "XScale-Core3" + .asciz "XScale-V3 based processor" .size cpu_xsc3_name, . - cpu_xsc3_name .align @@ -490,7 +489,7 @@ __xsc3_proc_info: PMD_SECT_CACHEABLE | \ PMD_SECT_AP_WRITE | \ PMD_SECT_AP_READ - .long PMD_TYPE_SECT | \ + .long PMD_TYPE_SECT | \ PMD_SECT_AP_WRITE | \ PMD_SECT_AP_READ b __xsc3_setup -- cgit v1.2.3 From 9d99df4b10eef130dacb5f772cd589c625b03634 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 5 Feb 2007 14:47:40 +0100 Subject: [ARM] 4128/1: Architecture compliant TTBR changing sequence On newer architectures (ARMv6, ARMv7), the depth of the prefetch and branch prediction is implementation defined and there is a small risk of wrong ASID tagging when changing TTBR0 before setting the new context id. The recommended solution is to set a reserved ASID during TTBR changing. This patch reserves ASID 0. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mm/context.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/context.c b/arch/arm/mm/context.c index 79e800202424..9da43a0fdcdf 100644 --- a/arch/arm/mm/context.c +++ b/arch/arm/mm/context.c @@ -19,7 +19,8 @@ unsigned int cpu_last_asid = { 1 << ASID_BITS }; /* * We fork()ed a process, and we need a new context for the child * to run in. We reserve version 0 for initial tasks so we will - * always allocate an ASID. + * always allocate an ASID. The ASID 0 is reserved for the TTBR + * register changing sequence. */ void __init_new_context(struct task_struct *tsk, struct mm_struct *mm) { @@ -38,8 +39,15 @@ void __new_context(struct mm_struct *mm) * If we've used up all our ASIDs, we need * to start a new version and flush the TLB. */ - if ((asid & ~ASID_MASK) == 0) + if ((asid & ~ASID_MASK) == 0) { + asid = ++cpu_last_asid; + /* set the reserved ASID before flushing the TLB */ + asm("mcr p15, 0, %0, c13, c0, 1 @ set reserved context ID\n" + : + : "r" (0)); + isb(); flush_tlb_all(); + } mm->context.id = asid; } -- cgit v1.2.3 From e6a5d66f58431c66c79e236f722a5ad7dd959ef3 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 5 Feb 2007 14:47:51 +0100 Subject: [ARM] 4129/1: Add barriers after the TLB operations The architecture specification states that TLB operations are guaranteed to be complete only after the execution of a DSB (Data Synchronisation Barrier, former Data Write Barrier or Drain Write Buffer). The branch target cache invalidation is also needed. The ISB (Instruction Synchronisation Barrier, formerly Prefetch Flush) is needed unless there will be a return from exception before the corresponding mapping is used (i.e. user mappings). Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mm/tlb-v6.S | 4 ++++ include/asm-arm/tlbflush.h | 50 +++++++++++++++++++++++++++++++++++----------- 2 files changed, 42 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/tlb-v6.S b/arch/arm/mm/tlb-v6.S index fd6adde39091..20f84bbaa9bb 100644 --- a/arch/arm/mm/tlb-v6.S +++ b/arch/arm/mm/tlb-v6.S @@ -53,6 +53,8 @@ ENTRY(v6wbi_flush_user_tlb_range) add r0, r0, #PAGE_SZ cmp r0, r1 blo 1b + mcr p15, 0, ip, c7, c5, 6 @ flush BTAC/BTB + mcr p15, 0, ip, c7, c10, 4 @ data synchronization barrier mov pc, lr /* @@ -80,7 +82,9 @@ ENTRY(v6wbi_flush_kern_tlb_range) add r0, r0, #PAGE_SZ cmp r0, r1 blo 1b + mcr p15, 0, r2, c7, c5, 6 @ flush BTAC/BTB mcr p15, 0, r2, c7, c10, 4 @ data synchronization barrier + mcr p15, 0, r2, c7, c5, 4 @ prefetch flush mov pc, lr .section ".text.init", #alloc, #execinstr diff --git a/include/asm-arm/tlbflush.h b/include/asm-arm/tlbflush.h index cd10a0b5f8ae..08c6991dc9c9 100644 --- a/include/asm-arm/tlbflush.h +++ b/include/asm-arm/tlbflush.h @@ -247,7 +247,7 @@ static inline void local_flush_tlb_all(void) const unsigned int __tlb_flag = __cpu_tlb_flags; if (tlb_flag(TLB_WB)) - asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (zero) : "cc"); + dsb(); if (tlb_flag(TLB_V3_FULL)) asm("mcr p15, 0, %0, c6, c0, 0" : : "r" (zero) : "cc"); @@ -257,6 +257,15 @@ static inline void local_flush_tlb_all(void) asm("mcr p15, 0, %0, c8, c6, 0" : : "r" (zero) : "cc"); if (tlb_flag(TLB_V4_I_FULL | TLB_V6_I_FULL)) asm("mcr p15, 0, %0, c8, c5, 0" : : "r" (zero) : "cc"); + + if (tlb_flag(TLB_V6_I_FULL | TLB_V6_D_FULL | + TLB_V6_I_PAGE | TLB_V6_D_PAGE | + TLB_V6_I_ASID | TLB_V6_D_ASID)) { + /* flush the branch target cache */ + asm("mcr p15, 0, %0, c7, c5, 6" : : "r" (zero) : "cc"); + dsb(); + isb(); + } } static inline void local_flush_tlb_mm(struct mm_struct *mm) @@ -266,7 +275,7 @@ static inline void local_flush_tlb_mm(struct mm_struct *mm) const unsigned int __tlb_flag = __cpu_tlb_flags; if (tlb_flag(TLB_WB)) - asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (zero) : "cc"); + dsb(); if (cpu_isset(smp_processor_id(), mm->cpu_vm_mask)) { if (tlb_flag(TLB_V3_FULL)) @@ -285,6 +294,14 @@ static inline void local_flush_tlb_mm(struct mm_struct *mm) asm("mcr p15, 0, %0, c8, c6, 2" : : "r" (asid) : "cc"); if (tlb_flag(TLB_V6_I_ASID)) asm("mcr p15, 0, %0, c8, c5, 2" : : "r" (asid) : "cc"); + + if (tlb_flag(TLB_V6_I_FULL | TLB_V6_D_FULL | + TLB_V6_I_PAGE | TLB_V6_D_PAGE | + TLB_V6_I_ASID | TLB_V6_D_ASID)) { + /* flush the branch target cache */ + asm("mcr p15, 0, %0, c7, c5, 6" : : "r" (zero) : "cc"); + dsb(); + } } static inline void @@ -296,7 +313,7 @@ local_flush_tlb_page(struct vm_area_struct *vma, unsigned long uaddr) uaddr = (uaddr & PAGE_MASK) | ASID(vma->vm_mm); if (tlb_flag(TLB_WB)) - asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (zero)); + dsb(); if (cpu_isset(smp_processor_id(), vma->vm_mm->cpu_vm_mask)) { if (tlb_flag(TLB_V3_PAGE)) @@ -317,6 +334,14 @@ local_flush_tlb_page(struct vm_area_struct *vma, unsigned long uaddr) asm("mcr p15, 0, %0, c8, c6, 1" : : "r" (uaddr) : "cc"); if (tlb_flag(TLB_V6_I_PAGE)) asm("mcr p15, 0, %0, c8, c5, 1" : : "r" (uaddr) : "cc"); + + if (tlb_flag(TLB_V6_I_FULL | TLB_V6_D_FULL | + TLB_V6_I_PAGE | TLB_V6_D_PAGE | + TLB_V6_I_ASID | TLB_V6_D_ASID)) { + /* flush the branch target cache */ + asm("mcr p15, 0, %0, c7, c5, 6" : : "r" (zero) : "cc"); + dsb(); + } } static inline void local_flush_tlb_kernel_page(unsigned long kaddr) @@ -327,7 +352,7 @@ static inline void local_flush_tlb_kernel_page(unsigned long kaddr) kaddr &= PAGE_MASK; if (tlb_flag(TLB_WB)) - asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (zero) : "cc"); + dsb(); if (tlb_flag(TLB_V3_PAGE)) asm("mcr p15, 0, %0, c6, c0, 0" : : "r" (kaddr) : "cc"); @@ -347,11 +372,14 @@ static inline void local_flush_tlb_kernel_page(unsigned long kaddr) if (tlb_flag(TLB_V6_I_PAGE)) asm("mcr p15, 0, %0, c8, c5, 1" : : "r" (kaddr) : "cc"); - /* The ARM ARM states that the completion of a TLB maintenance - * operation is only guaranteed by a DSB instruction - */ - if (tlb_flag(TLB_V6_U_PAGE | TLB_V6_D_PAGE | TLB_V6_I_PAGE)) - asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (zero) : "cc"); + if (tlb_flag(TLB_V6_I_FULL | TLB_V6_D_FULL | + TLB_V6_I_PAGE | TLB_V6_D_PAGE | + TLB_V6_I_ASID | TLB_V6_D_ASID)) { + /* flush the branch target cache */ + asm("mcr p15, 0, %0, c7, c5, 6" : : "r" (zero) : "cc"); + dsb(); + isb(); + } } /* @@ -369,15 +397,13 @@ static inline void local_flush_tlb_kernel_page(unsigned long kaddr) */ static inline void flush_pmd_entry(pmd_t *pmd) { - const unsigned int zero = 0; const unsigned int __tlb_flag = __cpu_tlb_flags; if (tlb_flag(TLB_DCLEAN)) asm("mcr p15, 0, %0, c7, c10, 1 @ flush_pmd" : : "r" (pmd) : "cc"); if (tlb_flag(TLB_WB)) - asm("mcr p15, 0, %0, c7, c10, 4 @ flush_pmd" - : : "r" (zero) : "cc"); + dsb(); } static inline void clean_pmd_entry(pmd_t *pmd) -- cgit v1.2.3 From 7f8e33546d17c7d8849be3a6623c3b6b3c9b588b Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 6 Feb 2007 17:29:53 +0000 Subject: [ARM] Don't call consistent_sync() for DMA coherent memory Memory allocated by the coherent memory allocators will be marked uncacheable, which means it's pointless calling consistent_sync() to perform cache maintainence on this memory; it's just a waste of CPU cycles. Moreover, with the (subsequent) merge of outer cache support, it actually breaks things to call consistent_sync() on anything but direct-mapped memory. Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 13 ++++++++++--- 1 file changed, 10 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index 2e635b814c14..272702accd8b 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -281,10 +281,14 @@ map_single(struct device *dev, void *ptr, size_t size, ptr = buf->safe; dma_addr = buf->safe_dma_addr; + } else { + /* + * We don't need to sync the DMA buffer since + * it was allocated via the coherent allocators. + */ + consistent_sync(ptr, size, dir); } - consistent_sync(ptr, size, dir); - return dma_addr; } @@ -397,7 +401,10 @@ sync_single(struct device *dev, dma_addr_t dma_addr, size_t size, default: BUG(); } - consistent_sync(buf->safe, size, dir); + /* + * No need to sync the safe buffer - it was allocated + * via the coherent allocators. + */ } else { consistent_sync(dma_to_virt(dev, dma_addr), size, dir); } -- cgit v1.2.3 From 953233dc9958ba2b29753d0f24e37a33a076a5f6 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 5 Feb 2007 14:48:08 +0100 Subject: [ARM] 4134/1: Add generic support for outer caches The outer cache can be L2 as on RealView/EB MPCore platform or even L3 or further on ARMv7 cores. This patch adds the generic support for flushing the outer cache in the DMA operations. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 1 + arch/arm/kernel/setup.c | 3 +++ arch/arm/mm/Kconfig | 3 +++ arch/arm/mm/consistent.c | 6 ++++++ include/asm-arm/cacheflush.h | 37 +++++++++++++++++++++++++++++++++++++ 5 files changed, 50 insertions(+) (limited to 'arch') diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index 272702accd8b..b4748e3171c6 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -338,6 +338,7 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, */ ptr = (unsigned long)buf->ptr; dmac_clean_range(ptr, ptr + size); + outer_clean_range(__pa(ptr), __pa(ptr) + size); } free_safe_buffer(device_info, buf); } diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index bbab134cd82d..243aea458057 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -88,6 +88,9 @@ struct cpu_user_fns cpu_user; #ifdef MULTI_CACHE struct cpu_cache_fns cpu_cache; #endif +#ifdef CONFIG_OUTER_CACHE +struct outer_cache_fns outer_cache; +#endif struct stack { u32 irq[3]; diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index aade2f72c920..a84eed9f8542 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -609,3 +609,6 @@ config NEEDS_SYSCALL_FOR_CMPXCHG Forget about fast user space cmpxchg support. It is just not possible. +config OUTER_CACHE + bool + default n diff --git a/arch/arm/mm/consistent.c b/arch/arm/mm/consistent.c index 6a9c362fef5e..83bd035c7d5e 100644 --- a/arch/arm/mm/consistent.c +++ b/arch/arm/mm/consistent.c @@ -208,6 +208,7 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, unsigned long kaddr = (unsigned long)page_address(page); memset(page_address(page), 0, size); dmac_flush_range(kaddr, kaddr + size); + outer_flush_range(__pa(kaddr), __pa(kaddr) + size); } /* @@ -485,15 +486,20 @@ void consistent_sync(void *vaddr, size_t size, int direction) unsigned long start = (unsigned long)vaddr; unsigned long end = start + size; + BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(end)); + switch (direction) { case DMA_FROM_DEVICE: /* invalidate only */ dmac_inv_range(start, end); + outer_inv_range(__pa(start), __pa(end)); break; case DMA_TO_DEVICE: /* writeback only */ dmac_clean_range(start, end); + outer_clean_range(__pa(start), __pa(end)); break; case DMA_BIDIRECTIONAL: /* writeback and invalidate */ dmac_flush_range(start, end); + outer_flush_range(__pa(start), __pa(end)); break; default: BUG(); diff --git a/include/asm-arm/cacheflush.h b/include/asm-arm/cacheflush.h index 5f531ea03059..ce60b3702ba5 100644 --- a/include/asm-arm/cacheflush.h +++ b/include/asm-arm/cacheflush.h @@ -190,6 +190,12 @@ struct cpu_cache_fns { void (*dma_flush_range)(unsigned long, unsigned long); }; +struct outer_cache_fns { + void (*inv_range)(unsigned long, unsigned long); + void (*clean_range)(unsigned long, unsigned long); + void (*flush_range)(unsigned long, unsigned long); +}; + /* * Select the calling method */ @@ -246,6 +252,37 @@ extern void dmac_flush_range(unsigned long, unsigned long); #endif +#ifdef CONFIG_OUTER_CACHE + +extern struct outer_cache_fns outer_cache; + +static inline void outer_inv_range(unsigned long start, unsigned long end) +{ + if (outer_cache.inv_range) + outer_cache.inv_range(start, end); +} +static inline void outer_clean_range(unsigned long start, unsigned long end) +{ + if (outer_cache.clean_range) + outer_cache.clean_range(start, end); +} +static inline void outer_flush_range(unsigned long start, unsigned long end) +{ + if (outer_cache.flush_range) + outer_cache.flush_range(start, end); +} + +#else + +static inline void outer_inv_range(unsigned long start, unsigned long end) +{ } +static inline void outer_clean_range(unsigned long start, unsigned long end) +{ } +static inline void outer_flush_range(unsigned long start, unsigned long end) +{ } + +#endif + /* * flush_cache_vmap() is used when creating mappings (eg, via vmap, * vmalloc, ioremap etc) in kernel space for pages. Since the -- cgit v1.2.3 From 7ae5a761d2ffc4cf7d3248e09f4d3da234434f30 Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 6 Feb 2007 17:39:31 +0000 Subject: [ARM] Convert DMA cache handling to take const void * args The DMA cache handling functions take virtual addresses, but in the form of unsigned long arguments. This leads to a little confusion about what exactly they take. So, convert them to take const void * instead. Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 7 +++---- arch/arm/mm/consistent.c | 13 ++++++------- include/asm-arm/cacheflush.h | 12 ++++++------ include/asm-arm/dma-mapping.h | 2 +- 4 files changed, 16 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index b4748e3171c6..2362c498f52e 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -321,12 +321,12 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, DO_STATS ( device_info->bounce_count++ ); if (dir == DMA_FROM_DEVICE || dir == DMA_BIDIRECTIONAL) { - unsigned long ptr; + void *ptr = buf->ptr; dev_dbg(dev, "%s: copy back safe %p to unsafe %p size %d\n", - __func__, buf->safe, buf->ptr, size); - memcpy(buf->ptr, buf->safe, size); + __func__, buf->safe, ptr, size); + memcpy(ptr, buf->safe, size); /* * DMA buffers must have the same cache properties @@ -336,7 +336,6 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, * bidirectional case because we know the cache * lines will be coherent with the data written. */ - ptr = (unsigned long)buf->ptr; dmac_clean_range(ptr, ptr + size); outer_clean_range(__pa(ptr), __pa(ptr) + size); } diff --git a/arch/arm/mm/consistent.c b/arch/arm/mm/consistent.c index 83bd035c7d5e..166aee13c4b1 100644 --- a/arch/arm/mm/consistent.c +++ b/arch/arm/mm/consistent.c @@ -205,10 +205,10 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, * kernel direct-mapped region for device DMA. */ { - unsigned long kaddr = (unsigned long)page_address(page); - memset(page_address(page), 0, size); - dmac_flush_range(kaddr, kaddr + size); - outer_flush_range(__pa(kaddr), __pa(kaddr) + size); + void *ptr = page_address(page); + memset(ptr, 0, size); + dmac_flush_range(ptr, ptr + size); + outer_flush_range(__pa(ptr), __pa(ptr) + size); } /* @@ -481,10 +481,9 @@ core_initcall(consistent_init); * platforms with CONFIG_DMABOUNCE. * Use the driver DMA support - see dma-mapping.h (dma_sync_*) */ -void consistent_sync(void *vaddr, size_t size, int direction) +void consistent_sync(const void *start, size_t size, int direction) { - unsigned long start = (unsigned long)vaddr; - unsigned long end = start + size; + const void *end = start + size; BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(end)); diff --git a/include/asm-arm/cacheflush.h b/include/asm-arm/cacheflush.h index ce60b3702ba5..afad32c76e6c 100644 --- a/include/asm-arm/cacheflush.h +++ b/include/asm-arm/cacheflush.h @@ -185,9 +185,9 @@ struct cpu_cache_fns { void (*coherent_user_range)(unsigned long, unsigned long); void (*flush_kern_dcache_page)(void *); - void (*dma_inv_range)(unsigned long, unsigned long); - void (*dma_clean_range)(unsigned long, unsigned long); - void (*dma_flush_range)(unsigned long, unsigned long); + void (*dma_inv_range)(const void *, const void *); + void (*dma_clean_range)(const void *, const void *); + void (*dma_flush_range)(const void *, const void *); }; struct outer_cache_fns { @@ -246,9 +246,9 @@ extern void __cpuc_flush_dcache_page(void *); #define dmac_clean_range __glue(_CACHE,_dma_clean_range) #define dmac_flush_range __glue(_CACHE,_dma_flush_range) -extern void dmac_inv_range(unsigned long, unsigned long); -extern void dmac_clean_range(unsigned long, unsigned long); -extern void dmac_flush_range(unsigned long, unsigned long); +extern void dmac_inv_range(const void *, const void *); +extern void dmac_clean_range(const void *, const void *); +extern void dmac_flush_range(const void *, const void *); #endif diff --git a/include/asm-arm/dma-mapping.h b/include/asm-arm/dma-mapping.h index 9bc46b486afb..a1d574cdcc14 100644 --- a/include/asm-arm/dma-mapping.h +++ b/include/asm-arm/dma-mapping.h @@ -17,7 +17,7 @@ * platforms with CONFIG_DMABOUNCE. * Use the driver DMA support - see dma-mapping.h (dma_sync_*) */ -extern void consistent_sync(void *kaddr, size_t size, int rw); +extern void consistent_sync(const void *kaddr, size_t size, int rw); /* * Return whether the given device DMA address mask can be supported -- cgit v1.2.3 From a93d48cc6019f84394b31d10c0d830a3b71696be Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 1 Feb 2007 09:22:23 +0100 Subject: [ARM] 4119/1: AT91: Fix build of AT91SAM9260 Fix build failure of AT91SAM9260. The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a "struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263) ethernet driver (macb.c) [developed on the AVR32 architecture] expects a "struct eth_platform_data". Since the platform data of the two drivers is very similar, we continue to use the "struct at91_eth_data" for all AT91 processors but add a #define eth_platform_data at91_eth_data in board.h to keep the MACB driver happy. Original patch by Jan Altenberg. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91rm9200/at91sam9260_devices.c | 6 +++--- arch/arm/mach-at91rm9200/board-sam9260ek.c | 2 +- include/asm-arm/arch-at91rm9200/board.h | 4 ++++ 3 files changed, 8 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91rm9200/at91sam9260_devices.c b/arch/arm/mach-at91rm9200/at91sam9260_devices.c index f42d3a40ec3c..f338f78eb943 100644 --- a/arch/arm/mach-at91rm9200/at91sam9260_devices.c +++ b/arch/arm/mach-at91rm9200/at91sam9260_devices.c @@ -128,7 +128,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {} #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) static u64 eth_dmamask = 0xffffffffUL; -static struct eth_platform_data eth_data; +static struct at91_eth_data eth_data; static struct resource eth_resources[] = { [0] = { @@ -155,7 +155,7 @@ static struct platform_device at91sam9260_eth_device = { .num_resources = ARRAY_SIZE(eth_resources), }; -void __init at91_add_device_eth(struct eth_platform_data *data) +void __init at91_add_device_eth(struct at91_eth_data *data) { if (!data) return; @@ -192,7 +192,7 @@ void __init at91_add_device_eth(struct eth_platform_data *data) platform_device_register(&at91sam9260_eth_device); } #else -void __init at91_add_device_eth(struct eth_platform_data *data) {} +void __init at91_add_device_eth(struct at91_eth_data *data) {} #endif diff --git a/arch/arm/mach-at91rm9200/board-sam9260ek.c b/arch/arm/mach-at91rm9200/board-sam9260ek.c index da5d58ac870b..37c7a7d195c3 100644 --- a/arch/arm/mach-at91rm9200/board-sam9260ek.c +++ b/arch/arm/mach-at91rm9200/board-sam9260ek.c @@ -118,7 +118,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct __initdata eth_platform_data ek_macb_data = { +static struct __initdata at91_eth_data ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; diff --git a/include/asm-arm/arch-at91rm9200/board.h b/include/asm-arm/arch-at91rm9200/board.h index 768e0fc6aa2f..f3a974ba3b51 100644 --- a/include/asm-arm/arch-at91rm9200/board.h +++ b/include/asm-arm/arch-at91rm9200/board.h @@ -69,6 +69,10 @@ struct at91_eth_data { }; extern void __init at91_add_device_eth(struct at91_eth_data *data); +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) +#define eth_platform_data at91_eth_data +#endif + /* USB Host */ struct at91_usbh_data { u8 ports; /* number of ports on root hub */ -- cgit v1.2.3 From 9d0412680e6c7b685ee466842047bcfb924d6dc5 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Mon, 5 Feb 2007 11:42:07 +0100 Subject: [ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directories Now that Linux includes support for the Atmel AT91SAM9260 and AT91SAM9261 processors in addition to the original Atmel AT91RM9200 (with support for more AT91 processors pending), the "mach-at91rm9200" and "arch-at91rm9200" directories should be renamed to indicate their more generic nature. The following git commands should be run BEFORE applying this patch: git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91 git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91 Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/Kconfig | 2 +- arch/arm/Makefile | 2 +- arch/arm/mach-at91/Kconfig | 148 ++++ arch/arm/mach-at91/Makefile | 49 ++ arch/arm/mach-at91/Makefile.boot | 9 + arch/arm/mach-at91/at91rm9200.c | 294 +++++++ arch/arm/mach-at91/at91rm9200_devices.c | 875 +++++++++++++++++++++ arch/arm/mach-at91/at91rm9200_time.c | 146 ++++ arch/arm/mach-at91/at91sam9260.c | 295 +++++++ arch/arm/mach-at91/at91sam9260_devices.c | 867 ++++++++++++++++++++ arch/arm/mach-at91/at91sam9261.c | 290 +++++++ arch/arm/mach-at91/at91sam9261_devices.c | 741 +++++++++++++++++ arch/arm/mach-at91/at91sam926x_time.c | 114 +++ arch/arm/mach-at91/board-1arm.c | 102 +++ arch/arm/mach-at91/board-carmeva.c | 149 ++++ arch/arm/mach-at91/board-csb337.c | 145 ++++ arch/arm/mach-at91/board-csb637.c | 109 +++ arch/arm/mach-at91/board-dk.c | 216 +++++ arch/arm/mach-at91/board-eb9200.c | 123 +++ arch/arm/mach-at91/board-ek.c | 174 ++++ arch/arm/mach-at91/board-kafa.c | 109 +++ arch/arm/mach-at91/board-kb9202.c | 143 ++++ arch/arm/mach-at91/board-sam9260ek.c | 202 +++++ arch/arm/mach-at91/board-sam9261ek.c | 259 ++++++ arch/arm/mach-at91/clock.c | 644 +++++++++++++++ arch/arm/mach-at91/clock.h | 31 + arch/arm/mach-at91/generic.h | 49 ++ arch/arm/mach-at91/gpio.c | 414 ++++++++++ arch/arm/mach-at91/irq.c | 168 ++++ arch/arm/mach-at91/leds.c | 99 +++ arch/arm/mach-at91/pm.c | 227 ++++++ arch/arm/mach-at91rm9200/Kconfig | 148 ---- arch/arm/mach-at91rm9200/Makefile | 49 -- arch/arm/mach-at91rm9200/Makefile.boot | 9 - arch/arm/mach-at91rm9200/at91rm9200.c | 294 ------- arch/arm/mach-at91rm9200/at91rm9200_devices.c | 875 --------------------- arch/arm/mach-at91rm9200/at91rm9200_time.c | 146 ---- arch/arm/mach-at91rm9200/at91sam9260.c | 295 ------- arch/arm/mach-at91rm9200/at91sam9260_devices.c | 867 -------------------- arch/arm/mach-at91rm9200/at91sam9261.c | 290 ------- arch/arm/mach-at91rm9200/at91sam9261_devices.c | 741 ----------------- arch/arm/mach-at91rm9200/at91sam926x_time.c | 114 --- arch/arm/mach-at91rm9200/board-1arm.c | 102 --- arch/arm/mach-at91rm9200/board-carmeva.c | 149 ---- arch/arm/mach-at91rm9200/board-csb337.c | 145 ---- arch/arm/mach-at91rm9200/board-csb637.c | 109 --- arch/arm/mach-at91rm9200/board-dk.c | 216 ----- arch/arm/mach-at91rm9200/board-eb9200.c | 123 --- arch/arm/mach-at91rm9200/board-ek.c | 174 ---- arch/arm/mach-at91rm9200/board-kafa.c | 109 --- arch/arm/mach-at91rm9200/board-kb9202.c | 143 ---- arch/arm/mach-at91rm9200/board-sam9260ek.c | 202 ----- arch/arm/mach-at91rm9200/board-sam9261ek.c | 259 ------ arch/arm/mach-at91rm9200/clock.c | 644 --------------- arch/arm/mach-at91rm9200/clock.h | 31 - arch/arm/mach-at91rm9200/generic.h | 49 -- arch/arm/mach-at91rm9200/gpio.c | 414 ---------- arch/arm/mach-at91rm9200/irq.c | 168 ---- arch/arm/mach-at91rm9200/leds.c | 99 --- arch/arm/mach-at91rm9200/pm.c | 227 ------ arch/avr32/mach-at32ap/clock.c | 2 +- arch/avr32/mach-at32ap/clock.h | 2 +- include/asm-arm/arch-at91/at91_aic.h | 53 ++ include/asm-arm/arch-at91/at91_dbgu.h | 45 ++ include/asm-arm/arch-at91/at91_ecc.h | 38 + include/asm-arm/arch-at91/at91_lcdc.h | 148 ++++ include/asm-arm/arch-at91/at91_mci.h | 106 +++ include/asm-arm/arch-at91/at91_pdc.h | 36 + include/asm-arm/arch-at91/at91_pio.h | 49 ++ include/asm-arm/arch-at91/at91_pit.h | 29 + include/asm-arm/arch-at91/at91_pmc.h | 92 +++ include/asm-arm/arch-at91/at91_rstc.h | 39 + include/asm-arm/arch-at91/at91_rtc.h | 75 ++ include/asm-arm/arch-at91/at91_rtt.h | 32 + include/asm-arm/arch-at91/at91_shdwc.h | 33 + include/asm-arm/arch-at91/at91_spi.h | 81 ++ include/asm-arm/arch-at91/at91_ssc.h | 106 +++ include/asm-arm/arch-at91/at91_st.h | 49 ++ include/asm-arm/arch-at91/at91_tc.h | 146 ++++ include/asm-arm/arch-at91/at91_twi.h | 57 ++ include/asm-arm/arch-at91/at91_wdt.h | 34 + include/asm-arm/arch-at91/at91rm9200.h | 291 +++++++ include/asm-arm/arch-at91/at91rm9200_emac.h | 138 ++++ include/asm-arm/arch-at91/at91rm9200_mc.h | 160 ++++ include/asm-arm/arch-at91/at91sam9260.h | 125 +++ include/asm-arm/arch-at91/at91sam9260_matrix.h | 78 ++ include/asm-arm/arch-at91/at91sam9261.h | 292 +++++++ include/asm-arm/arch-at91/at91sam9261_matrix.h | 62 ++ include/asm-arm/arch-at91/at91sam926x_mc.h | 134 ++++ include/asm-arm/arch-at91/board.h | 121 +++ include/asm-arm/arch-at91/cpu.h | 49 ++ include/asm-arm/arch-at91/debug-macro.S | 39 + include/asm-arm/arch-at91/dma.h | 19 + include/asm-arm/arch-at91/entry-macro.S | 26 + include/asm-arm/arch-at91/gpio.h | 199 +++++ include/asm-arm/arch-at91/hardware.h | 88 +++ include/asm-arm/arch-at91/io.h | 32 + include/asm-arm/arch-at91/irqs.h | 44 ++ include/asm-arm/arch-at91/memory.h | 39 + include/asm-arm/arch-at91/system.h | 53 ++ include/asm-arm/arch-at91/timex.h | 37 + include/asm-arm/arch-at91/uncompress.h | 56 ++ include/asm-arm/arch-at91/vmalloc.h | 26 + include/asm-arm/arch-at91rm9200/at91_aic.h | 53 -- include/asm-arm/arch-at91rm9200/at91_dbgu.h | 45 -- include/asm-arm/arch-at91rm9200/at91_ecc.h | 38 - include/asm-arm/arch-at91rm9200/at91_lcdc.h | 148 ---- include/asm-arm/arch-at91rm9200/at91_mci.h | 106 --- include/asm-arm/arch-at91rm9200/at91_pdc.h | 36 - include/asm-arm/arch-at91rm9200/at91_pio.h | 49 -- include/asm-arm/arch-at91rm9200/at91_pit.h | 29 - include/asm-arm/arch-at91rm9200/at91_pmc.h | 92 --- include/asm-arm/arch-at91rm9200/at91_rstc.h | 39 - include/asm-arm/arch-at91rm9200/at91_rtc.h | 75 -- include/asm-arm/arch-at91rm9200/at91_rtt.h | 32 - include/asm-arm/arch-at91rm9200/at91_shdwc.h | 33 - include/asm-arm/arch-at91rm9200/at91_spi.h | 81 -- include/asm-arm/arch-at91rm9200/at91_ssc.h | 106 --- include/asm-arm/arch-at91rm9200/at91_st.h | 49 -- include/asm-arm/arch-at91rm9200/at91_tc.h | 146 ---- include/asm-arm/arch-at91rm9200/at91_twi.h | 57 -- include/asm-arm/arch-at91rm9200/at91_wdt.h | 34 - include/asm-arm/arch-at91rm9200/at91rm9200.h | 291 ------- include/asm-arm/arch-at91rm9200/at91rm9200_emac.h | 138 ---- include/asm-arm/arch-at91rm9200/at91rm9200_mc.h | 160 ---- include/asm-arm/arch-at91rm9200/at91sam9260.h | 125 --- .../asm-arm/arch-at91rm9200/at91sam9260_matrix.h | 78 -- include/asm-arm/arch-at91rm9200/at91sam9261.h | 292 ------- .../asm-arm/arch-at91rm9200/at91sam9261_matrix.h | 62 -- include/asm-arm/arch-at91rm9200/at91sam926x_mc.h | 134 ---- include/asm-arm/arch-at91rm9200/board.h | 121 --- include/asm-arm/arch-at91rm9200/cpu.h | 49 -- include/asm-arm/arch-at91rm9200/debug-macro.S | 39 - include/asm-arm/arch-at91rm9200/dma.h | 19 - include/asm-arm/arch-at91rm9200/entry-macro.S | 26 - include/asm-arm/arch-at91rm9200/gpio.h | 199 ----- include/asm-arm/arch-at91rm9200/hardware.h | 88 --- include/asm-arm/arch-at91rm9200/io.h | 32 - include/asm-arm/arch-at91rm9200/irqs.h | 44 -- include/asm-arm/arch-at91rm9200/memory.h | 39 - include/asm-arm/arch-at91rm9200/system.h | 53 -- include/asm-arm/arch-at91rm9200/timex.h | 37 - include/asm-arm/arch-at91rm9200/uncompress.h | 56 -- include/asm-arm/arch-at91rm9200/vmalloc.h | 26 - include/asm-avr32/arch-at32ap/at91_pdc.h | 2 +- 145 files changed, 10552 insertions(+), 10552 deletions(-) create mode 100644 arch/arm/mach-at91/Kconfig create mode 100644 arch/arm/mach-at91/Makefile create mode 100644 arch/arm/mach-at91/Makefile.boot create mode 100644 arch/arm/mach-at91/at91rm9200.c create mode 100644 arch/arm/mach-at91/at91rm9200_devices.c create mode 100644 arch/arm/mach-at91/at91rm9200_time.c create mode 100644 arch/arm/mach-at91/at91sam9260.c create mode 100644 arch/arm/mach-at91/at91sam9260_devices.c create mode 100644 arch/arm/mach-at91/at91sam9261.c create mode 100644 arch/arm/mach-at91/at91sam9261_devices.c create mode 100644 arch/arm/mach-at91/at91sam926x_time.c create mode 100644 arch/arm/mach-at91/board-1arm.c create mode 100644 arch/arm/mach-at91/board-carmeva.c create mode 100644 arch/arm/mach-at91/board-csb337.c create mode 100644 arch/arm/mach-at91/board-csb637.c create mode 100644 arch/arm/mach-at91/board-dk.c create mode 100644 arch/arm/mach-at91/board-eb9200.c create mode 100644 arch/arm/mach-at91/board-ek.c create mode 100644 arch/arm/mach-at91/board-kafa.c create mode 100644 arch/arm/mach-at91/board-kb9202.c create mode 100644 arch/arm/mach-at91/board-sam9260ek.c create mode 100644 arch/arm/mach-at91/board-sam9261ek.c create mode 100644 arch/arm/mach-at91/clock.c create mode 100644 arch/arm/mach-at91/clock.h create mode 100644 arch/arm/mach-at91/generic.h create mode 100644 arch/arm/mach-at91/gpio.c create mode 100644 arch/arm/mach-at91/irq.c create mode 100644 arch/arm/mach-at91/leds.c create mode 100644 arch/arm/mach-at91/pm.c delete mode 100644 arch/arm/mach-at91rm9200/Kconfig delete mode 100644 arch/arm/mach-at91rm9200/Makefile delete mode 100644 arch/arm/mach-at91rm9200/Makefile.boot delete mode 100644 arch/arm/mach-at91rm9200/at91rm9200.c delete mode 100644 arch/arm/mach-at91rm9200/at91rm9200_devices.c delete mode 100644 arch/arm/mach-at91rm9200/at91rm9200_time.c delete mode 100644 arch/arm/mach-at91rm9200/at91sam9260.c delete mode 100644 arch/arm/mach-at91rm9200/at91sam9260_devices.c delete mode 100644 arch/arm/mach-at91rm9200/at91sam9261.c delete mode 100644 arch/arm/mach-at91rm9200/at91sam9261_devices.c delete mode 100644 arch/arm/mach-at91rm9200/at91sam926x_time.c delete mode 100644 arch/arm/mach-at91rm9200/board-1arm.c delete mode 100644 arch/arm/mach-at91rm9200/board-carmeva.c delete mode 100644 arch/arm/mach-at91rm9200/board-csb337.c delete mode 100644 arch/arm/mach-at91rm9200/board-csb637.c delete mode 100644 arch/arm/mach-at91rm9200/board-dk.c delete mode 100644 arch/arm/mach-at91rm9200/board-eb9200.c delete mode 100644 arch/arm/mach-at91rm9200/board-ek.c delete mode 100644 arch/arm/mach-at91rm9200/board-kafa.c delete mode 100644 arch/arm/mach-at91rm9200/board-kb9202.c delete mode 100644 arch/arm/mach-at91rm9200/board-sam9260ek.c delete mode 100644 arch/arm/mach-at91rm9200/board-sam9261ek.c delete mode 100644 arch/arm/mach-at91rm9200/clock.c delete mode 100644 arch/arm/mach-at91rm9200/clock.h delete mode 100644 arch/arm/mach-at91rm9200/generic.h delete mode 100644 arch/arm/mach-at91rm9200/gpio.c delete mode 100644 arch/arm/mach-at91rm9200/irq.c delete mode 100644 arch/arm/mach-at91rm9200/leds.c delete mode 100644 arch/arm/mach-at91rm9200/pm.c create mode 100644 include/asm-arm/arch-at91/at91_aic.h create mode 100644 include/asm-arm/arch-at91/at91_dbgu.h create mode 100644 include/asm-arm/arch-at91/at91_ecc.h create mode 100644 include/asm-arm/arch-at91/at91_lcdc.h create mode 100644 include/asm-arm/arch-at91/at91_mci.h create mode 100644 include/asm-arm/arch-at91/at91_pdc.h create mode 100644 include/asm-arm/arch-at91/at91_pio.h create mode 100644 include/asm-arm/arch-at91/at91_pit.h create mode 100644 include/asm-arm/arch-at91/at91_pmc.h create mode 100644 include/asm-arm/arch-at91/at91_rstc.h create mode 100644 include/asm-arm/arch-at91/at91_rtc.h create mode 100644 include/asm-arm/arch-at91/at91_rtt.h create mode 100644 include/asm-arm/arch-at91/at91_shdwc.h create mode 100644 include/asm-arm/arch-at91/at91_spi.h create mode 100644 include/asm-arm/arch-at91/at91_ssc.h create mode 100644 include/asm-arm/arch-at91/at91_st.h create mode 100644 include/asm-arm/arch-at91/at91_tc.h create mode 100644 include/asm-arm/arch-at91/at91_twi.h create mode 100644 include/asm-arm/arch-at91/at91_wdt.h create mode 100644 include/asm-arm/arch-at91/at91rm9200.h create mode 100644 include/asm-arm/arch-at91/at91rm9200_emac.h create mode 100644 include/asm-arm/arch-at91/at91rm9200_mc.h create mode 100644 include/asm-arm/arch-at91/at91sam9260.h create mode 100644 include/asm-arm/arch-at91/at91sam9260_matrix.h create mode 100644 include/asm-arm/arch-at91/at91sam9261.h create mode 100644 include/asm-arm/arch-at91/at91sam9261_matrix.h create mode 100644 include/asm-arm/arch-at91/at91sam926x_mc.h create mode 100644 include/asm-arm/arch-at91/board.h create mode 100644 include/asm-arm/arch-at91/cpu.h create mode 100644 include/asm-arm/arch-at91/debug-macro.S create mode 100644 include/asm-arm/arch-at91/dma.h create mode 100644 include/asm-arm/arch-at91/entry-macro.S create mode 100644 include/asm-arm/arch-at91/gpio.h create mode 100644 include/asm-arm/arch-at91/hardware.h create mode 100644 include/asm-arm/arch-at91/io.h create mode 100644 include/asm-arm/arch-at91/irqs.h create mode 100644 include/asm-arm/arch-at91/memory.h create mode 100644 include/asm-arm/arch-at91/system.h create mode 100644 include/asm-arm/arch-at91/timex.h create mode 100644 include/asm-arm/arch-at91/uncompress.h create mode 100644 include/asm-arm/arch-at91/vmalloc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_aic.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_dbgu.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_ecc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_lcdc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_mci.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_pdc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_pio.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_pit.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_pmc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_rstc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_rtc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_rtt.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_shdwc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_spi.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_ssc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_st.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_tc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_twi.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91_wdt.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91rm9200.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91rm9200_emac.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91rm9200_mc.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91sam9260.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91sam9260_matrix.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91sam9261.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91sam9261_matrix.h delete mode 100644 include/asm-arm/arch-at91rm9200/at91sam926x_mc.h delete mode 100644 include/asm-arm/arch-at91rm9200/board.h delete mode 100644 include/asm-arm/arch-at91rm9200/cpu.h delete mode 100644 include/asm-arm/arch-at91rm9200/debug-macro.S delete mode 100644 include/asm-arm/arch-at91rm9200/dma.h delete mode 100644 include/asm-arm/arch-at91rm9200/entry-macro.S delete mode 100644 include/asm-arm/arch-at91rm9200/gpio.h delete mode 100644 include/asm-arm/arch-at91rm9200/hardware.h delete mode 100644 include/asm-arm/arch-at91rm9200/io.h delete mode 100644 include/asm-arm/arch-at91rm9200/irqs.h delete mode 100644 include/asm-arm/arch-at91rm9200/memory.h delete mode 100644 include/asm-arm/arch-at91rm9200/system.h delete mode 100644 include/asm-arm/arch-at91rm9200/timex.h delete mode 100644 include/asm-arm/arch-at91rm9200/uncompress.h delete mode 100644 include/asm-arm/arch-at91rm9200/vmalloc.h (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6783c2e5512d..9c7565c8f376 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -377,7 +377,7 @@ source "arch/arm/mach-aaec2000/Kconfig" source "arch/arm/mach-realview/Kconfig" -source "arch/arm/mach-at91rm9200/Kconfig" +source "arch/arm/mach-at91/Kconfig" source "arch/arm/mach-netx/Kconfig" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 000f1100b553..0205547fa45c 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -124,7 +124,7 @@ endif machine-$(CONFIG_ARCH_H720X) := h720x machine-$(CONFIG_ARCH_AAEC2000) := aaec2000 machine-$(CONFIG_ARCH_REALVIEW) := realview - machine-$(CONFIG_ARCH_AT91) := at91rm9200 + machine-$(CONFIG_ARCH_AT91) := at91 machine-$(CONFIG_ARCH_EP93XX) := ep93xx machine-$(CONFIG_ARCH_PNX4008) := pnx4008 machine-$(CONFIG_ARCH_NETX) := netx diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig new file mode 100644 index 000000000000..9f11db8af233 --- /dev/null +++ b/arch/arm/mach-at91/Kconfig @@ -0,0 +1,148 @@ +if ARCH_AT91 + +menu "Atmel AT91 System-on-Chip" + +choice + prompt "Atmel AT91 Processor" + +config ARCH_AT91RM9200 + bool "AT91RM9200" + +config ARCH_AT91SAM9260 + bool "AT91SAM9260" + +config ARCH_AT91SAM9261 + bool "AT91SAM9261" + +endchoice + +# ---------------------------------------------------------- + +if ARCH_AT91RM9200 + +comment "AT91RM9200 Board Type" + +config MACH_ONEARM + bool "Ajeco 1ARM Single Board Computer" + depends on ARCH_AT91RM9200 + help + Select this if you are using Ajeco's 1ARM Single Board Computer. + + +config ARCH_AT91RM9200DK + bool "Atmel AT91RM9200-DK Development board" + depends on ARCH_AT91RM9200 + help + Select this if you are using Atmel's AT91RM9200-DK Development board. + (Discontinued) + +config MACH_AT91RM9200EK + bool "Atmel AT91RM9200-EK Evaluation Kit" + depends on ARCH_AT91RM9200 + help + Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit. + + +config MACH_CSB337 + bool "Cogent CSB337" + depends on ARCH_AT91RM9200 + help + Select this if you are using Cogent's CSB337 board. + + +config MACH_CSB637 + bool "Cogent CSB637" + depends on ARCH_AT91RM9200 + help + Select this if you are using Cogent's CSB637 board. + + +config MACH_CARMEVA + bool "Conitec ARM&EVA" + depends on ARCH_AT91RM9200 + help + Select this if you are using Conitec's AT91RM9200-MCU-Module. + + +config MACH_ATEB9200 + bool "Embest ATEB9200" + depends on ARCH_AT91RM9200 + help + Select this if you are using Embest's ATEB9200 board. + + +config MACH_KB9200 + bool "KwikByte KB920x" + depends on ARCH_AT91RM9200 + help + Select this if you are using KwikByte's KB920x board. + + +config MACH_KAFA + bool "Sperry-Sun KAFA board" + depends on ARCH_AT91RM9200 + help + Select this if you are using Sperry-Sun's KAFA board. + +endif + +# ---------------------------------------------------------- + +if ARCH_AT91SAM9260 + +comment "AT91SAM9260 Board Type" + +config MACH_AT91SAM9260EK + bool "Atmel AT91SAM9260-EK Evaluation Kit" + depends on ARCH_AT91SAM9260 + help + Select this if you are using Atmel's AT91SAM9260-EK Evaluation Kit. + + +endif + +# ---------------------------------------------------------- + +if ARCH_AT91SAM9261 + +comment "AT91SAM9261 Board Type" + +config MACH_AT91SAM9261EK + bool "Atmel AT91SAM9261-EK Evaluation Kit" + depends on ARCH_AT91SAM9261 + help + Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit. + + +endif + +# ---------------------------------------------------------- + +comment "AT91 Board Options" + +config MTD_AT91_DATAFLASH_CARD + bool "Enable DataFlash Card support" + depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK) + help + Enable support for the DataFlash card. + +config MTD_NAND_AT91_BUSWIDTH_16 + bool "Enable 16-bit data bus interface to NAND flash" + depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK) + help + On AT91SAM926x boards both types of NAND flash can be present + (8 and 16 bit data bus width). + +# ---------------------------------------------------------- + +comment "AT91 Feature Selections" + +config AT91_PROGRAMMABLE_CLOCKS + bool "Programmable Clocks" + help + Select this if you need to program one or more of the PCK0..PCK3 + programmable clock outputs. + +endmenu + +endif diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile new file mode 100644 index 000000000000..cf777007847a --- /dev/null +++ b/arch/arm/mach-at91/Makefile @@ -0,0 +1,49 @@ +# +# Makefile for the linux kernel. +# + +obj-y := clock.o irq.o gpio.o +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_PM) += pm.o + +# CPU-specific support +obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devices.o +obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o +obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o + +# AT91RM9200 board-specific support +obj-$(CONFIG_MACH_ONEARM) += board-1arm.o +obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o +obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o +obj-$(CONFIG_MACH_CSB337) += board-csb337.o +obj-$(CONFIG_MACH_CSB637) += board-csb637.o +obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o +obj-$(CONFIG_MACH_KB9200) += board-kb9202.o +obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o +obj-$(CONFIG_MACH_KAFA) += board-kafa.o + +# AT91SAM9260 board-specific support +obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o + +# AT91SAM9261 board-specific support +obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o + +# LEDs support +led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o +led-$(CONFIG_MACH_AT91RM9200EK) += leds.o +led-$(CONFIG_MACH_CSB337) += leds.o +led-$(CONFIG_MACH_CSB637) += leds.o +led-$(CONFIG_MACH_KB9200) += leds.o +led-$(CONFIG_MACH_KAFA) += leds.o +obj-$(CONFIG_LEDS) += $(led-y) + +# VGA support +#obj-$(CONFIG_FB_S1D13XXX) += ics1523.o + + +ifeq ($(CONFIG_PM_DEBUG),y) +CFLAGS_pm.o += -DDEBUG +endif diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot new file mode 100644 index 000000000000..e667dcc7cd34 --- /dev/null +++ b/arch/arm/mach-at91/Makefile.boot @@ -0,0 +1,9 @@ +# Note: the following conditions must always be true: +# ZRELADDR == virt_to_phys(TEXTADDR) +# PARAMS_PHYS must be within 4MB of ZRELADDR +# INITRD_PHYS must be in RAM + + zreladdr-y := 0x20008000 +params_phys-y := 0x20000100 +initrd_phys-y := 0x20410000 + diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c new file mode 100644 index 000000000000..870d4a4eb806 --- /dev/null +++ b/arch/arm/mach-at91/at91rm9200.c @@ -0,0 +1,294 @@ +/* + * arch/arm/mach-at91/at91rm9200.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" +#include "clock.h" + +static struct map_desc at91rm9200_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91_BASE_SYS), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_EMAC, + .pfn = __phys_to_pfn(AT91RM9200_BASE_EMAC), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91RM9200_SRAM_SIZE, + .pfn = __phys_to_pfn(AT91RM9200_SRAM_BASE), + .length = AT91RM9200_SRAM_SIZE, + .type = MT_DEVICE, + }, +}; + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk udc_clk = { + .name = "udc_clk", + .pmc_mask = 1 << AT91RM9200_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .pmc_mask = 1 << AT91RM9200_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ether_clk = { + .name = "ether_clk", + .pmc_mask = 1 << AT91RM9200_ID_EMAC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91RM9200_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi_clk = { + .name = "twi_clk", + .pmc_mask = 1 << AT91RM9200_ID_TWI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91RM9200_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91RM9200_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91RM9200_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart3_clk = { + .name = "usart3_clk", + .pmc_mask = 1 << AT91RM9200_ID_US3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi_clk = { + .name = "spi_clk", + .pmc_mask = 1 << AT91RM9200_ID_SPI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioC_clk = { + .name = "pioC_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioD_clk = { + .name = "pioD_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOD, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioC_clk, + &pioD_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &usart3_clk, + &mmc_clk, + &udc_clk, + &twi_clk, + &spi_clk, + // ssc 0 .. ssc2 + // tc0 .. tc5 + &ohci_clk, + ðer_clk, + // irq0 .. irq6 +}; + +/* + * The four programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; +static struct clk pck2 = { + .name = "pck2", + .pmc_mask = AT91_PMC_PCK2, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 2, +}; +static struct clk pck3 = { + .name = "pck3", + .pmc_mask = AT91_PMC_PCK3, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 3, +}; + +static void __init at91rm9200_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); + clk_register(&pck2); + clk_register(&pck3); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91rm9200_gpio[] = { + { + .id = AT91RM9200_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91RM9200_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91RM9200_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + }, { + .id = AT91RM9200_ID_PIOD, + .offset = AT91_PIOD, + .clock = &pioD_clk, + } +}; + +static void at91rm9200_reset(void) +{ + /* + * Perform a hardware reset with the use of the Watchdog timer. + */ + at91_sys_write(AT91_ST_WDMR, AT91_ST_RSTEN | AT91_ST_EXTEN | 1); + at91_sys_write(AT91_ST_CR, AT91_ST_WDRST); +} + + +/* -------------------------------------------------------------------- + * AT91RM9200 processor initialization + * -------------------------------------------------------------------- */ +void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks) +{ + /* Map peripherals */ + iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); + + at91_arch_reset = at91rm9200_reset; + at91_extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1) + | (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3) + | (1 << AT91RM9200_ID_IRQ4) | (1 << AT91RM9200_ID_IRQ5) + | (1 << AT91RM9200_ID_IRQ6); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91rm9200_register_clocks(); + + /* Initialize GPIO subsystem */ + at91_gpio_init(at91rm9200_gpio, banks); +} + + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller (FIQ) */ + 7, /* System Peripherals */ + 0, /* Parallel IO Controller A */ + 0, /* Parallel IO Controller B */ + 0, /* Parallel IO Controller C */ + 0, /* Parallel IO Controller D */ + 6, /* USART 0 */ + 6, /* USART 1 */ + 6, /* USART 2 */ + 6, /* USART 3 */ + 0, /* Multimedia Card Interface */ + 4, /* USB Device Port */ + 0, /* Two-Wire Interface */ + 6, /* Serial Peripheral Interface */ + 5, /* Serial Synchronous Controller 0 */ + 5, /* Serial Synchronous Controller 1 */ + 5, /* Serial Synchronous Controller 2 */ + 0, /* Timer Counter 0 */ + 0, /* Timer Counter 1 */ + 0, /* Timer Counter 2 */ + 0, /* Timer Counter 3 */ + 0, /* Timer Counter 4 */ + 0, /* Timer Counter 5 */ + 3, /* USB Host port */ + 3, /* Ethernet MAC */ + 0, /* Advanced Interrupt Controller (IRQ0) */ + 0, /* Advanced Interrupt Controller (IRQ1) */ + 0, /* Advanced Interrupt Controller (IRQ2) */ + 0, /* Advanced Interrupt Controller (IRQ3) */ + 0, /* Advanced Interrupt Controller (IRQ4) */ + 0, /* Advanced Interrupt Controller (IRQ5) */ + 0 /* Advanced Interrupt Controller (IRQ6) */ +}; + +void __init at91rm9200_init_interrupts(unsigned int priority[NR_AIC_IRQS]) +{ + if (!priority) + priority = at91rm9200_default_irq_priority; + + /* Initialize the AIC interrupt controller */ + at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); +} diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c new file mode 100644 index 000000000000..a06498ccc826 --- /dev/null +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -0,0 +1,875 @@ +/* + * arch/arm/mach-at91/at91rm9200_devices.c + * + * Copyright (C) 2005 Thibaut VARENE + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include +#include + +#include + +#include +#include +#include +#include + +#include "generic.h" + +#define SZ_512 0x00000200 +#define SZ_256 0x00000100 +#define SZ_16 0x00000010 + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource usbh_resources[] = { + [0] = { + .start = AT91RM9200_UHP_BASE, + .end = AT91RM9200_UHP_BASE + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_UHP, + .end = AT91RM9200_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_usbh_device = { + .name = "at91_ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = usbh_resources, + .num_resources = ARRAY_SIZE(usbh_resources), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + if (!data) + return; + + usbh_data = *data; + platform_device_register(&at91rm9200_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource udc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_UDP, + .end = AT91RM9200_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_UDP, + .end = AT91RM9200_ID_UDP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = udc_resources, + .num_resources = ARRAY_SIZE(udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + if (data->pullup_pin) + at91_set_gpio_output(data->pullup_pin, 0); + + udc_data = *data; + platform_device_register(&at91rm9200_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Ethernet + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE) +static u64 eth_dmamask = 0xffffffffUL; +static struct at91_eth_data eth_data; + +static struct resource eth_resources[] = { + [0] = { + .start = AT91_VA_BASE_EMAC, + .end = AT91_VA_BASE_EMAC + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_EMAC, + .end = AT91RM9200_ID_EMAC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_eth_device = { + .name = "at91_ether", + .id = -1, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = ð_data, + }, + .resource = eth_resources, + .num_resources = ARRAY_SIZE(eth_resources), +}; + +void __init at91_add_device_eth(struct at91_eth_data *data) +{ + if (!data) + return; + + if (data->phy_irq_pin) { + at91_set_gpio_input(data->phy_irq_pin, 0); + at91_set_deglitch(data->phy_irq_pin, 1); + } + + /* Pins used for MII and RMII */ + at91_set_A_periph(AT91_PIN_PA16, 0); /* EMDIO */ + at91_set_A_periph(AT91_PIN_PA15, 0); /* EMDC */ + at91_set_A_periph(AT91_PIN_PA14, 0); /* ERXER */ + at91_set_A_periph(AT91_PIN_PA13, 0); /* ERX1 */ + at91_set_A_periph(AT91_PIN_PA12, 0); /* ERX0 */ + at91_set_A_periph(AT91_PIN_PA11, 0); /* ECRS_ECRSDV */ + at91_set_A_periph(AT91_PIN_PA10, 0); /* ETX1 */ + at91_set_A_periph(AT91_PIN_PA9, 0); /* ETX0 */ + at91_set_A_periph(AT91_PIN_PA8, 0); /* ETXEN */ + at91_set_A_periph(AT91_PIN_PA7, 0); /* ETXCK_EREFCK */ + + if (!data->is_rmii) { + at91_set_B_periph(AT91_PIN_PB19, 0); /* ERXCK */ + at91_set_B_periph(AT91_PIN_PB18, 0); /* ECOL */ + at91_set_B_periph(AT91_PIN_PB17, 0); /* ERXDV */ + at91_set_B_periph(AT91_PIN_PB16, 0); /* ERX3 */ + at91_set_B_periph(AT91_PIN_PB15, 0); /* ERX2 */ + at91_set_B_periph(AT91_PIN_PB14, 0); /* ETXER */ + at91_set_B_periph(AT91_PIN_PB13, 0); /* ETX3 */ + at91_set_B_periph(AT91_PIN_PB12, 0); /* ETX2 */ + } + + eth_data = *data; + platform_device_register(&at91rm9200_eth_device); +} +#else +void __init at91_add_device_eth(struct at91_eth_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Compact Flash / PCMCIA + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) +static struct at91_cf_data cf_data; + +#define CF_BASE AT91_CHIPSELECT_4 + +static struct resource cf_resources[] = { + [0] = { + .start = CF_BASE, + /* ties up CS4, CS5 and CS6 */ + .end = CF_BASE + (0x30000000 - 1), + .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT, + }, +}; + +static struct platform_device at91rm9200_cf_device = { + .name = "at91_cf", + .id = -1, + .dev = { + .platform_data = &cf_data, + }, + .resource = cf_resources, + .num_resources = ARRAY_SIZE(cf_resources), +}; + +void __init at91_add_device_cf(struct at91_cf_data *data) +{ + unsigned int csa; + + if (!data) + return; + + data->chipselect = 4; /* can only use EBI ChipSelect 4 */ + + /* CF takes over CS4, CS5, CS6 */ + csa = at91_sys_read(AT91_EBI_CSA); + at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH); + + /* + * Static memory controller timing adjustments. + * REVISIT: these timings are in terms of MCK cycles, so + * when MCK changes (cpufreq etc) so must these values... + */ + at91_sys_write(AT91_SMC_CSR(4), + AT91_SMC_ACSS_STD + | AT91_SMC_DBW_16 + | AT91_SMC_BAT + | AT91_SMC_WSEN + | AT91_SMC_NWS_(32) /* wait states */ + | AT91_SMC_RWSETUP_(6) /* setup time */ + | AT91_SMC_RWHOLD_(4) /* hold time */ + ); + + /* input/irq */ + if (data->irq_pin) { + at91_set_gpio_input(data->irq_pin, 1); + at91_set_deglitch(data->irq_pin, 1); + } + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + + /* outputs, initially off */ + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + at91_set_gpio_output(data->rst_pin, 0); + + /* force poweron defaults for these pins ... */ + at91_set_A_periph(AT91_PIN_PC9, 0); /* A25/CFRNW */ + at91_set_A_periph(AT91_PIN_PC10, 0); /* NCS4/CFCS */ + at91_set_A_periph(AT91_PIN_PC11, 0); /* NCS5/CFCE1 */ + at91_set_A_periph(AT91_PIN_PC12, 0); /* NCS6/CFCE2 */ + + /* nWAIT is _not_ a default setting */ + at91_set_A_periph(AT91_PIN_PC6, 1); /* nWAIT */ + + cf_data = *data; + platform_device_register(&at91rm9200_cf_device); +} +#else +void __init at91_add_device_cf(struct at91_cf_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_MCI, + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_MCI, + .end = AT91RM9200_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "at91_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mmc(struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + if (data->slot_b) { + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 1); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PA10, 1); + at91_set_B_periph(AT91_PIN_PA11, 1); + at91_set_B_periph(AT91_PIN_PA12, 1); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 1); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PB3, 1); + at91_set_B_periph(AT91_PIN_PB4, 1); + at91_set_B_periph(AT91_PIN_PB5, 1); + } + } + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); +} +#else +void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +#define NAND_BASE AT91_CHIPSELECT_3 + +static struct resource nand_resources[] = { + { + .start = NAND_BASE, + .end = NAND_BASE + SZ_8M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91rm9200_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = nand_resources, + .num_resources = ARRAY_SIZE(nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + unsigned int csa; + + if (!data) + return; + + /* enable the address range of CS3 */ + csa = at91_sys_read(AT91_EBI_CSA); + at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA); + + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN + | AT91_SMC_NWS_(5) + | AT91_SMC_TDF_(1) + | AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */ + | AT91_SMC_RWHOLD_(1) /* tDH Data Hold Time 20 - ns */ + ); + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */ + at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */ + + nand_data = *data; + platform_device_register(&at91rm9200_nand_device); +} +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) + +static struct resource twi_resources[] = { + [0] = { + .start = AT91RM9200_BASE_TWI, + .end = AT91RM9200_BASE_TWI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_TWI, + .end = AT91RM9200_ID_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_twi_device = { + .name = "at91_i2c", + .id = -1, + .resource = twi_resources, + .num_resources = ARRAY_SIZE(twi_resources), +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PA25, 1); + + at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PA26, 1); + + platform_device_register(&at91rm9200_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource spi_resources[] = { + [0] = { + .start = AT91RM9200_BASE_SPI, + .end = AT91RM9200_BASE_SPI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_SPI, + .end = AT91RM9200_ID_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_spi_device = { + .name = "at91_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi_resources, + .num_resources = ARRAY_SIZE(spi_resources), +}; + +static const unsigned spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 }; + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + + at91_set_A_periph(AT91_PIN_PA0, 0); /* MISO */ + at91_set_A_periph(AT91_PIN_PA1, 0); /* MOSI */ + at91_set_A_periph(AT91_PIN_PA2, 0); /* SPCK */ + + /* Enable SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else + cs_pin = spi_standard_cs[devices[i].chip_select]; + +#ifdef CONFIG_SPI_AT91_MANUAL_CS + at91_set_gpio_output(cs_pin, 1); +#else + at91_set_A_periph(cs_pin, 0); +#endif + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + at91_clock_associate("spi_clk", &at91rm9200_spi_device.dev, "spi"); + platform_device_register(&at91rm9200_spi_device); +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif + + +/* -------------------------------------------------------------------- + * RTC + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE) +static struct platform_device at91rm9200_rtc_device = { + .name = "at91_rtc", + .id = -1, + .num_resources = 0, +}; + +static void __init at91_add_device_rtc(void) +{ + platform_device_register(&at91rm9200_rtc_device); +} +#else +static void __init at91_add_device_rtc(void) {} +#endif + + +/* -------------------------------------------------------------------- + * Watchdog + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_AT91RM9200_WATCHDOG) || defined(CONFIG_AT91RM9200_WATCHDOG_MODULE) +static struct platform_device at91rm9200_wdt_device = { + .name = "at91_wdt", + .id = -1, + .num_resources = 0, +}; + +static void __init at91_add_device_watchdog(void) +{ + platform_device_register(&at91rm9200_wdt_device); +} +#else +static void __init at91_add_device_watchdog(void) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SERIAL_ATMEL) +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ + .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), +}; + +static struct platform_device at91rm9200_dbgu_device = { + .name = "atmel_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA30, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PA31, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US0, + .end = AT91RM9200_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US0, + .end = AT91RM9200_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart0_device = { + .name = "atmel_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */ + + /* + * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21. + * We need to drive the pin manually. Default is off (RTS is active low). + */ + at91_set_gpio_output(AT91_PIN_PA21, 1); +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US1, + .end = AT91RM9200_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US1, + .end = AT91RM9200_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart1_device = { + .name = "atmel_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */ + at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */ + at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */ + at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */ + at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */ + at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */ + at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US2, + .end = AT91RM9200_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US2, + .end = AT91RM9200_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart2_device = { + .name = "atmel_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */ + at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */ +} + +static struct resource uart3_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US3, + .end = AT91RM9200_BASE_US3 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US3, + .end = AT91RM9200_ID_US3, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart3_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart3_device = { + .name = "atmel_usart", + .id = 4, + .dev = { + .platform_data = &uart3_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart3_resources, + .num_resources = ARRAY_SIZE(uart3_resources), +}; + +static inline void configure_usart3_pins(void) +{ + at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */ + at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */ +} + +struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ +struct platform_device *atmel_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91rm9200_uart0_device; + at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91rm9200_uart1_device; + at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91rm9200_uart2_device; + at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart"); + break; + case 3: + configure_usart3_pins(); + at91_uarts[i] = &at91rm9200_uart3_device; + at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart"); + break; + case 4: + configure_dbgu_pins(); + at91_uarts[i] = &at91rm9200_dbgu_device; + at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < ATMEL_MAX_UART) + atmel_default_console_device = at91_uarts[config->console_tty]; + if (!atmel_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < ATMEL_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ + +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + at91_add_device_rtc(); + at91_add_device_watchdog(); + return 0; +} + +arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c new file mode 100644 index 000000000000..949199a244c7 --- /dev/null +++ b/arch/arm/mach-at91/at91rm9200_time.c @@ -0,0 +1,146 @@ +/* + * linux/arch/arm/mach-at91/at91rm9200_time.c + * + * Copyright (C) 2003 SAN People + * Copyright (C) 2003 ATMEL + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +static unsigned long last_crtr; + +/* + * The ST_CRTR is updated asynchronously to the master clock. It is therefore + * necessary to read it twice (with the same value) to ensure accuracy. + */ +static inline unsigned long read_CRTR(void) { + unsigned long x1, x2; + + do { + x1 = at91_sys_read(AT91_ST_CRTR); + x2 = at91_sys_read(AT91_ST_CRTR); + } while (x1 != x2); + + return x1; +} + +/* + * Returns number of microseconds since last timer interrupt. Note that interrupts + * will have been disabled by do_gettimeofday() + * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. + * 'tick' is usecs per jiffy (linux/timex.h). + */ +static unsigned long at91rm9200_gettimeoffset(void) +{ + unsigned long elapsed; + + elapsed = (read_CRTR() - last_crtr) & AT91_ST_ALMV; + + return (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH; +} + +/* + * IRQ handler for the timer. + */ +static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id) +{ + if (at91_sys_read(AT91_ST_SR) & AT91_ST_PITS) { /* This is a shared interrupt */ + write_seqlock(&xtime_lock); + + while (((read_CRTR() - last_crtr) & AT91_ST_ALMV) >= LATCH) { + timer_tick(); + last_crtr = (last_crtr + LATCH) & AT91_ST_ALMV; + } + + write_sequnlock(&xtime_lock); + + return IRQ_HANDLED; + } + else + return IRQ_NONE; /* not handled */ +} + +static struct irqaction at91rm9200_timer_irq = { + .name = "at91_tick", + .flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER, + .handler = at91rm9200_timer_interrupt +}; + +void at91rm9200_timer_reset(void) +{ + last_crtr = 0; + + /* Real time counter incremented every 30.51758 microseconds */ + at91_sys_write(AT91_ST_RTMR, 1); + + /* Set Period Interval timer */ + at91_sys_write(AT91_ST_PIMR, LATCH); + + /* Clear any pending interrupts */ + (void) at91_sys_read(AT91_ST_SR); + + /* Enable Period Interval Timer interrupt */ + at91_sys_write(AT91_ST_IER, AT91_ST_PITS); +} + +/* + * Set up timer interrupt. + */ +void __init at91rm9200_timer_init(void) +{ + /* Disable all timer interrupts */ + at91_sys_write(AT91_ST_IDR, AT91_ST_PITS | AT91_ST_WDOVF | AT91_ST_RTTINC | AT91_ST_ALMS); + (void) at91_sys_read(AT91_ST_SR); /* Clear any pending interrupts */ + + /* Make IRQs happen for the system timer */ + setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq); + + /* Change the kernel's 'tick' value to 10009 usec. (the default is 10000) */ + tick_usec = (LATCH * 1000000) / CLOCK_TICK_RATE; + + /* Initialize and enable the timer interrupt */ + at91rm9200_timer_reset(); +} + +#ifdef CONFIG_PM +static void at91rm9200_timer_suspend(void) +{ + /* disable Period Interval Timer interrupt */ + at91_sys_write(AT91_ST_IDR, AT91_ST_PITS); +} +#else +#define at91rm9200_timer_suspend NULL +#endif + +struct sys_timer at91rm9200_timer = { + .init = at91rm9200_timer_init, + .offset = at91rm9200_gettimeoffset, + .suspend = at91rm9200_timer_suspend, + .resume = at91rm9200_timer_reset, +}; + diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c new file mode 100644 index 000000000000..ffc4c0944740 --- /dev/null +++ b/arch/arm/mach-at91/at91sam9260.c @@ -0,0 +1,295 @@ +/* + * arch/arm/mach-at91/at91sam9260.c + * + * Copyright (C) 2006 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" +#include "clock.h" + +static struct map_desc at91sam9260_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91_BASE_SYS), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE, + .pfn = __phys_to_pfn(AT91SAM9260_SRAM0_BASE), + .length = AT91SAM9260_SRAM0_SIZE, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE - AT91SAM9260_SRAM1_SIZE, + .pfn = __phys_to_pfn(AT91SAM9260_SRAM1_BASE), + .length = AT91SAM9260_SRAM1_SIZE, + .type = MT_DEVICE, + }, +}; + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91SAM9260_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91SAM9260_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioC_clk = { + .name = "pioC_clk", + .pmc_mask = 1 << AT91SAM9260_ID_PIOC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk adc_clk = { + .name = "adc_clk", + .pmc_mask = 1 << AT91SAM9260_ID_ADC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91SAM9260_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91SAM9260_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91SAM9260_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91SAM9260_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk udc_clk = { + .name = "udc_clk", + .pmc_mask = 1 << AT91SAM9260_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi_clk = { + .name = "twi_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TWI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi0_clk = { + .name = "spi0_clk", + .pmc_mask = 1 << AT91SAM9260_ID_SPI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi1_clk = { + .name = "spi1_clk", + .pmc_mask = 1 << AT91SAM9260_ID_SPI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .pmc_mask = 1 << AT91SAM9260_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ether_clk = { + .name = "ether_clk", + .pmc_mask = 1 << AT91SAM9260_ID_EMAC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk isi_clk = { + .name = "isi_clk", + .pmc_mask = 1 << AT91SAM9260_ID_ISI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart3_clk = { + .name = "usart3_clk", + .pmc_mask = 1 << AT91SAM9260_ID_US3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart4_clk = { + .name = "usart4_clk", + .pmc_mask = 1 << AT91SAM9260_ID_US4, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart5_clk = { + .name = "usart5_clk", + .pmc_mask = 1 << AT91SAM9260_ID_US5, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioC_clk, + &adc_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &mmc_clk, + &udc_clk, + &twi_clk, + &spi0_clk, + &spi1_clk, + // ssc + // tc0 .. tc2 + &ohci_clk, + ðer_clk, + &isi_clk, + &usart3_clk, + &usart4_clk, + &usart5_clk, + // tc3 .. tc5 + // irq0 .. irq2 +}; + +/* + * The two programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; + +static void __init at91sam9260_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91sam9260_gpio[] = { + { + .id = AT91SAM9260_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91SAM9260_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91SAM9260_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + } +}; + +static void at91sam9260_reset(void) +{ + at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); +} + + +/* -------------------------------------------------------------------- + * AT91SAM9260 processor initialization + * -------------------------------------------------------------------- */ + +void __init at91sam9260_initialize(unsigned long main_clock) +{ + /* Map peripherals */ + iotable_init(at91sam9260_io_desc, ARRAY_SIZE(at91sam9260_io_desc)); + + at91_arch_reset = at91sam9260_reset; + at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1) + | (1 << AT91SAM9260_ID_IRQ2); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91sam9260_register_clocks(); + + /* Register GPIO subsystem */ + at91_gpio_init(at91sam9260_gpio, 3); +} + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller */ + 7, /* System Peripherals */ + 0, /* Parallel IO Controller A */ + 0, /* Parallel IO Controller B */ + 0, /* Parallel IO Controller C */ + 0, /* Analog-to-Digital Converter */ + 6, /* USART 0 */ + 6, /* USART 1 */ + 6, /* USART 2 */ + 0, /* Multimedia Card Interface */ + 4, /* USB Device Port */ + 0, /* Two-Wire Interface */ + 6, /* Serial Peripheral Interface 0 */ + 6, /* Serial Peripheral Interface 1 */ + 5, /* Serial Synchronous Controller */ + 0, + 0, + 0, /* Timer Counter 0 */ + 0, /* Timer Counter 1 */ + 0, /* Timer Counter 2 */ + 3, /* USB Host port */ + 3, /* Ethernet */ + 0, /* Image Sensor Interface */ + 6, /* USART 3 */ + 6, /* USART 4 */ + 6, /* USART 5 */ + 0, /* Timer Counter 3 */ + 0, /* Timer Counter 4 */ + 0, /* Timer Counter 5 */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ +}; + +void __init at91sam9260_init_interrupts(unsigned int priority[NR_AIC_IRQS]) +{ + if (!priority) + priority = at91sam9260_default_irq_priority; + + /* Initialize the AIC interrupt controller */ + at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); +} diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c new file mode 100644 index 000000000000..4adff70b9ba0 --- /dev/null +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -0,0 +1,867 @@ +/* + * arch/arm/mach-at91/at91sam9260_devices.c + * + * Copyright (C) 2006 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include +#include + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" + +#define SZ_512 0x00000200 +#define SZ_256 0x00000100 +#define SZ_16 0x00000010 + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource usbh_resources[] = { + [0] = { + .start = AT91SAM9260_UHP_BASE, + .end = AT91SAM9260_UHP_BASE + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_UHP, + .end = AT91SAM9260_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91_usbh_device = { + .name = "at91_ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = usbh_resources, + .num_resources = ARRAY_SIZE(usbh_resources), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + if (!data) + return; + + usbh_data = *data; + platform_device_register(&at91_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource udc_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_UDP, + .end = AT91SAM9260_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_UDP, + .end = AT91SAM9260_ID_UDP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = udc_resources, + .num_resources = ARRAY_SIZE(udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + + /* Pullup pin is handled internally by USB device peripheral */ + + udc_data = *data; + platform_device_register(&at91_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Ethernet + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) +static u64 eth_dmamask = 0xffffffffUL; +static struct at91_eth_data eth_data; + +static struct resource eth_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_EMAC, + .end = AT91SAM9260_BASE_EMAC + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_EMAC, + .end = AT91SAM9260_ID_EMAC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9260_eth_device = { + .name = "macb", + .id = -1, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = ð_data, + }, + .resource = eth_resources, + .num_resources = ARRAY_SIZE(eth_resources), +}; + +void __init at91_add_device_eth(struct at91_eth_data *data) +{ + if (!data) + return; + + if (data->phy_irq_pin) { + at91_set_gpio_input(data->phy_irq_pin, 0); + at91_set_deglitch(data->phy_irq_pin, 1); + } + + /* Pins used for MII and RMII */ + at91_set_A_periph(AT91_PIN_PA19, 0); /* ETXCK_EREFCK */ + at91_set_A_periph(AT91_PIN_PA17, 0); /* ERXDV */ + at91_set_A_periph(AT91_PIN_PA14, 0); /* ERX0 */ + at91_set_A_periph(AT91_PIN_PA15, 0); /* ERX1 */ + at91_set_A_periph(AT91_PIN_PA18, 0); /* ERXER */ + at91_set_A_periph(AT91_PIN_PA16, 0); /* ETXEN */ + at91_set_A_periph(AT91_PIN_PA12, 0); /* ETX0 */ + at91_set_A_periph(AT91_PIN_PA13, 0); /* ETX1 */ + at91_set_A_periph(AT91_PIN_PA21, 0); /* EMDIO */ + at91_set_A_periph(AT91_PIN_PA20, 0); /* EMDC */ + + if (!data->is_rmii) { + at91_set_B_periph(AT91_PIN_PA28, 0); /* ECRS */ + at91_set_B_periph(AT91_PIN_PA29, 0); /* ECOL */ + at91_set_B_periph(AT91_PIN_PA25, 0); /* ERX2 */ + at91_set_B_periph(AT91_PIN_PA26, 0); /* ERX3 */ + at91_set_B_periph(AT91_PIN_PA27, 0); /* ERXCK */ + at91_set_B_periph(AT91_PIN_PA23, 0); /* ETX2 */ + at91_set_B_periph(AT91_PIN_PA24, 0); /* ETX3 */ + at91_set_B_periph(AT91_PIN_PA22, 0); /* ETXER */ + } + + eth_data = *data; + platform_device_register(&at91sam9260_eth_device); +} +#else +void __init at91_add_device_eth(struct at91_eth_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_MCI, + .end = AT91SAM9260_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_MCI, + .end = AT91SAM9260_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9260_mmc_device = { + .name = "at91_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mmc(struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA8, 0); + + if (data->slot_b) { + /* CMD */ + at91_set_B_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA0, 1); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PA5, 1); + at91_set_B_periph(AT91_PIN_PA4, 1); + at91_set_B_periph(AT91_PIN_PA3, 1); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA7, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA6, 1); + if (data->wire4) { + at91_set_A_periph(AT91_PIN_PA9, 1); + at91_set_A_periph(AT91_PIN_PA10, 1); + at91_set_A_periph(AT91_PIN_PA11, 1); + } + } + + mmc_data = *data; + platform_device_register(&at91sam9260_mmc_device); +} +#else +void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +#define NAND_BASE AT91_CHIPSELECT_3 + +static struct resource nand_resources[] = { + { + .start = NAND_BASE, + .end = NAND_BASE + SZ_8M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91sam9260_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = nand_resources, + .num_resources = ARRAY_SIZE(nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + unsigned long csa, mode; + + if (!data) + return; + + csa = at91_sys_read(AT91_MATRIX_EBICSA); + at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC); + + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) + | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + nand_data = *data; + platform_device_register(&at91sam9260_nand_device); +} +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) + +static struct resource twi_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_TWI, + .end = AT91SAM9260_BASE_TWI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_TWI, + .end = AT91SAM9260_ID_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9260_twi_device = { + .name = "at91_i2c", + .id = -1, + .resource = twi_resources, + .num_resources = ARRAY_SIZE(twi_resources), +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PA23, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PA23, 1); + + at91_set_A_periph(AT91_PIN_PA24, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PA24, 1); + + platform_device_register(&at91sam9260_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource spi0_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_SPI0, + .end = AT91SAM9260_BASE_SPI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_SPI0, + .end = AT91SAM9260_ID_SPI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9260_spi0_device = { + .name = "atmel_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi0_resources, + .num_resources = ARRAY_SIZE(spi0_resources), +}; + +static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PC11, AT91_PIN_PC16, AT91_PIN_PC17 }; + +static struct resource spi1_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_SPI1, + .end = AT91SAM9260_BASE_SPI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_SPI1, + .end = AT91SAM9260_ID_SPI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9260_spi1_device = { + .name = "atmel_spi", + .id = 1, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi1_resources, + .num_resources = ARRAY_SIZE(spi1_resources), +}; + +static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PC5, AT91_PIN_PC4, AT91_PIN_PC3 }; + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + short enable_spi0 = 0; + short enable_spi1 = 0; + + /* Choose SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else if (devices[i].bus_num == 0) + cs_pin = spi0_standard_cs[devices[i].chip_select]; + else + cs_pin = spi1_standard_cs[devices[i].chip_select]; + + if (devices[i].bus_num == 0) + enable_spi0 = 1; + else + enable_spi1 = 1; + + /* enable chip-select pin */ + at91_set_gpio_output(cs_pin, 1); + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + + /* Configure SPI bus(es) */ + if (enable_spi0) { + at91_set_A_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */ + at91_set_A_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */ + at91_set_A_periph(AT91_PIN_PA2, 0); /* SPI1_SPCK */ + + at91_clock_associate("spi0_clk", &at91sam9260_spi0_device.dev, "spi_clk"); + platform_device_register(&at91sam9260_spi0_device); + } + if (enable_spi1) { + at91_set_A_periph(AT91_PIN_PB0, 0); /* SPI1_MISO */ + at91_set_A_periph(AT91_PIN_PB1, 0); /* SPI1_MOSI */ + at91_set_A_periph(AT91_PIN_PB2, 0); /* SPI1_SPCK */ + + at91_clock_associate("spi1_clk", &at91sam9260_spi1_device.dev, "spi_clk"); + platform_device_register(&at91sam9260_spi1_device); + } +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ +#if defined(CONFIG_SERIAL_ATMEL) +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ + .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), +}; + +static struct platform_device at91sam9260_dbgu_device = { + .name = "atmel_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB14, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PB15, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_US0, + .end = AT91SAM9260_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_US0, + .end = AT91SAM9260_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9260_uart0_device = { + .name = "atmel_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB4, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PB5, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS0 */ + at91_set_A_periph(AT91_PIN_PB27, 0); /* CTS0 */ + at91_set_A_periph(AT91_PIN_PB24, 0); /* DTR0 */ + at91_set_A_periph(AT91_PIN_PB22, 0); /* DSR0 */ + at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD0 */ + at91_set_A_periph(AT91_PIN_PB25, 0); /* RI0 */ +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_US1, + .end = AT91SAM9260_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_US1, + .end = AT91SAM9260_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9260_uart1_device = { + .name = "atmel_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB6, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PB7, 0); /* RXD1 */ + at91_set_A_periph(AT91_PIN_PB28, 0); /* RTS1 */ + at91_set_A_periph(AT91_PIN_PB29, 0); /* CTS1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_US2, + .end = AT91SAM9260_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_US2, + .end = AT91SAM9260_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9260_uart2_device = { + .name = "atmel_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB8, 1); /* TXD2 */ + at91_set_A_periph(AT91_PIN_PB9, 0); /* RXD2 */ +} + +static struct resource uart3_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_US3, + .end = AT91SAM9260_BASE_US3 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_US3, + .end = AT91SAM9260_ID_US3, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart3_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9260_uart3_device = { + .name = "atmel_usart", + .id = 4, + .dev = { + .platform_data = &uart3_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart3_resources, + .num_resources = ARRAY_SIZE(uart3_resources), +}; + +static inline void configure_usart3_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB10, 1); /* TXD3 */ + at91_set_A_periph(AT91_PIN_PB11, 0); /* RXD3 */ +} + +static struct resource uart4_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_US4, + .end = AT91SAM9260_BASE_US4 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_US4, + .end = AT91SAM9260_ID_US4, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart4_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9260_uart4_device = { + .name = "atmel_usart", + .id = 5, + .dev = { + .platform_data = &uart4_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart4_resources, + .num_resources = ARRAY_SIZE(uart4_resources), +}; + +static inline void configure_usart4_pins(void) +{ + at91_set_B_periph(AT91_PIN_PA31, 1); /* TXD4 */ + at91_set_B_periph(AT91_PIN_PA30, 0); /* RXD4 */ +} + +static struct resource uart5_resources[] = { + [0] = { + .start = AT91SAM9260_BASE_US5, + .end = AT91SAM9260_BASE_US5 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9260_ID_US5, + .end = AT91SAM9260_ID_US5, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart5_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9260_uart5_device = { + .name = "atmel_usart", + .id = 6, + .dev = { + .platform_data = &uart5_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart5_resources, + .num_resources = ARRAY_SIZE(uart5_resources), +}; + +static inline void configure_usart5_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB12, 1); /* TXD5 */ + at91_set_A_periph(AT91_PIN_PB13, 0); /* RXD5 */ +} + +struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ +struct platform_device *atmel_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91sam9260_uart0_device; + at91_clock_associate("usart0_clk", &at91sam9260_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91sam9260_uart1_device; + at91_clock_associate("usart1_clk", &at91sam9260_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91sam9260_uart2_device; + at91_clock_associate("usart2_clk", &at91sam9260_uart2_device.dev, "usart"); + break; + case 3: + configure_usart3_pins(); + at91_uarts[i] = &at91sam9260_uart3_device; + at91_clock_associate("usart3_clk", &at91sam9260_uart3_device.dev, "usart"); + break; + case 4: + configure_usart4_pins(); + at91_uarts[i] = &at91sam9260_uart4_device; + at91_clock_associate("usart4_clk", &at91sam9260_uart4_device.dev, "usart"); + break; + case 5: + configure_usart5_pins(); + at91_uarts[i] = &at91sam9260_uart5_device; + at91_clock_associate("usart5_clk", &at91sam9260_uart5_device.dev, "usart"); + break; + case 6: + configure_dbgu_pins(); + at91_uarts[i] = &at91sam9260_dbgu_device; + at91_clock_associate("mck", &at91sam9260_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < ATMEL_MAX_UART) + atmel_default_console_device = at91_uarts[config->console_tty]; + if (!atmel_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < ATMEL_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + return 0; +} + +arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c new file mode 100644 index 000000000000..47e02ff7e872 --- /dev/null +++ b/arch/arm/mach-at91/at91sam9261.c @@ -0,0 +1,290 @@ +/* + * arch/arm/mach-at91/at91sam9261.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" +#include "clock.h" + +static struct map_desc at91sam9261_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91_BASE_SYS), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9261_SRAM_SIZE, + .pfn = __phys_to_pfn(AT91SAM9261_SRAM_BASE), + .length = AT91SAM9261_SRAM_SIZE, + .type = MT_DEVICE, + }, +}; + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91SAM9261_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91SAM9261_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioC_clk = { + .name = "pioC_clk", + .pmc_mask = 1 << AT91SAM9261_ID_PIOC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91SAM9261_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91SAM9261_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91SAM9261_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91SAM9261_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk udc_clk = { + .name = "udc_clk", + .pmc_mask = 1 << AT91SAM9261_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi_clk = { + .name = "twi_clk", + .pmc_mask = 1 << AT91SAM9261_ID_TWI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi0_clk = { + .name = "spi0_clk", + .pmc_mask = 1 << AT91SAM9261_ID_SPI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi1_clk = { + .name = "spi1_clk", + .pmc_mask = 1 << AT91SAM9261_ID_SPI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .pmc_mask = 1 << AT91SAM9261_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk lcdc_clk = { + .name = "lcdc_clk", + .pmc_mask = 1 << AT91SAM9261_ID_LCDC, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioC_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &mmc_clk, + &udc_clk, + &twi_clk, + &spi0_clk, + &spi1_clk, + // ssc 0 .. ssc2 + // tc0 .. tc2 + &ohci_clk, + &lcdc_clk, + // irq0 .. irq2 +}; + +/* + * The four programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; +static struct clk pck2 = { + .name = "pck2", + .pmc_mask = AT91_PMC_PCK2, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 2, +}; +static struct clk pck3 = { + .name = "pck3", + .pmc_mask = AT91_PMC_PCK3, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 3, +}; + +/* HClocks */ +static struct clk hck0 = { + .name = "hck0", + .pmc_mask = AT91_PMC_HCK0, + .type = CLK_TYPE_SYSTEM, + .id = 0, +}; +static struct clk hck1 = { + .name = "hck1", + .pmc_mask = AT91_PMC_HCK1, + .type = CLK_TYPE_SYSTEM, + .id = 1, +}; + +static void __init at91sam9261_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); + clk_register(&pck2); + clk_register(&pck3); + + clk_register(&hck0); + clk_register(&hck1); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91sam9261_gpio[] = { + { + .id = AT91SAM9261_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91SAM9261_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91SAM9261_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + } +}; + +static void at91sam9261_reset(void) +{ + at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); +} + + +/* -------------------------------------------------------------------- + * AT91SAM9261 processor initialization + * -------------------------------------------------------------------- */ + +void __init at91sam9261_initialize(unsigned long main_clock) +{ + /* Map peripherals */ + iotable_init(at91sam9261_io_desc, ARRAY_SIZE(at91sam9261_io_desc)); + + at91_arch_reset = at91sam9261_reset; + at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1) + | (1 << AT91SAM9261_ID_IRQ2); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91sam9261_register_clocks(); + + /* Register GPIO subsystem */ + at91_gpio_init(at91sam9261_gpio, 3); +} + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller */ + 7, /* System Peripherals */ + 0, /* Parallel IO Controller A */ + 0, /* Parallel IO Controller B */ + 0, /* Parallel IO Controller C */ + 0, + 6, /* USART 0 */ + 6, /* USART 1 */ + 6, /* USART 2 */ + 0, /* Multimedia Card Interface */ + 4, /* USB Device Port */ + 0, /* Two-Wire Interface */ + 6, /* Serial Peripheral Interface 0 */ + 6, /* Serial Peripheral Interface 1 */ + 5, /* Serial Synchronous Controller 0 */ + 5, /* Serial Synchronous Controller 1 */ + 5, /* Serial Synchronous Controller 2 */ + 0, /* Timer Counter 0 */ + 0, /* Timer Counter 1 */ + 0, /* Timer Counter 2 */ + 3, /* USB Host port */ + 3, /* LCD Controller */ + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ +}; + +void __init at91sam9261_init_interrupts(unsigned int priority[NR_AIC_IRQS]) +{ + if (!priority) + priority = at91sam9261_default_irq_priority; + + /* Initialize the AIC interrupt controller */ + at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); +} diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c new file mode 100644 index 000000000000..3249de08d1f3 --- /dev/null +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -0,0 +1,741 @@ +/* + * arch/arm/mach-at91/at91sam9261_devices.c + * + * Copyright (C) 2005 Thibaut VARENE + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include +#include + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" + +#define SZ_512 0x00000200 +#define SZ_256 0x00000100 +#define SZ_16 0x00000010 + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource usbh_resources[] = { + [0] = { + .start = AT91SAM9261_UHP_BASE, + .end = AT91SAM9261_UHP_BASE + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_UHP, + .end = AT91SAM9261_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_usbh_device = { + .name = "at91_ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = usbh_resources, + .num_resources = ARRAY_SIZE(usbh_resources), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + if (!data) + return; + + usbh_data = *data; + platform_device_register(&at91sam9261_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource udc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_UDP, + .end = AT91SAM9261_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_UDP, + .end = AT91SAM9261_ID_UDP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = udc_resources, + .num_resources = ARRAY_SIZE(udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + unsigned long x; + + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + + /* Pullup pin is handled internally */ + x = at91_sys_read(AT91_MATRIX_USBPUCR); + at91_sys_write(AT91_MATRIX_USBPUCR, x | AT91_MATRIX_USBPUCR_PUON); + + udc_data = *data; + platform_device_register(&at91sam9261_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource mmc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_MCI, + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_MCI, + .end = AT91SAM9261_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_mmc_device = { + .name = "at91_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = mmc_resources, + .num_resources = ARRAY_SIZE(mmc_resources), +}; + +void __init at91_add_device_mmc(struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + + /* CLK */ + at91_set_B_periph(AT91_PIN_PA2, 0); + + /* CMD */ + at91_set_B_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA0, 1); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PA4, 1); + at91_set_B_periph(AT91_PIN_PA5, 1); + at91_set_B_periph(AT91_PIN_PA6, 1); + } + + mmc_data = *data; + platform_device_register(&at91sam9261_mmc_device); +} +#else +void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +#define NAND_BASE AT91_CHIPSELECT_3 + +static struct resource nand_resources[] = { + { + .start = NAND_BASE, + .end = NAND_BASE + SZ_256M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = nand_resources, + .num_resources = ARRAY_SIZE(nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + unsigned long csa, mode; + + if (!data) + return; + + csa = at91_sys_read(AT91_MATRIX_EBICSA); + at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC); + + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) + | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ + at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */ + + nand_data = *data; + platform_device_register(&at91_nand_device); +} + +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) + +static struct resource twi_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_TWI, + .end = AT91SAM9261_BASE_TWI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_TWI, + .end = AT91SAM9261_ID_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_twi_device = { + .name = "at91_i2c", + .id = -1, + .resource = twi_resources, + .num_resources = ARRAY_SIZE(twi_resources), +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PA7, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PA7, 1); + + at91_set_A_periph(AT91_PIN_PA8, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PA8, 1); + + platform_device_register(&at91sam9261_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource spi0_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_SPI0, + .end = AT91SAM9261_BASE_SPI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_SPI0, + .end = AT91SAM9261_ID_SPI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_spi0_device = { + .name = "atmel_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi0_resources, + .num_resources = ARRAY_SIZE(spi0_resources), +}; + +static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 }; + +static struct resource spi1_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_SPI1, + .end = AT91SAM9261_BASE_SPI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_SPI1, + .end = AT91SAM9261_ID_SPI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9261_spi1_device = { + .name = "atmel_spi", + .id = 1, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi1_resources, + .num_resources = ARRAY_SIZE(spi1_resources), +}; + +static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB28, AT91_PIN_PA24, AT91_PIN_PA25, AT91_PIN_PA26 }; + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + short enable_spi0 = 0; + short enable_spi1 = 0; + + /* Choose SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else if (devices[i].bus_num == 0) + cs_pin = spi0_standard_cs[devices[i].chip_select]; + else + cs_pin = spi1_standard_cs[devices[i].chip_select]; + + if (devices[i].bus_num == 0) + enable_spi0 = 1; + else + enable_spi1 = 1; + + /* enable chip-select pin */ + at91_set_gpio_output(cs_pin, 1); + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + + /* Configure SPI bus(es) */ + if (enable_spi0) { + at91_set_A_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */ + at91_set_A_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */ + at91_set_A_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */ + + at91_clock_associate("spi0_clk", &at91sam9261_spi0_device.dev, "spi_clk"); + platform_device_register(&at91sam9261_spi0_device); + } + if (enable_spi1) { + at91_set_A_periph(AT91_PIN_PB30, 0); /* SPI1_MISO */ + at91_set_A_periph(AT91_PIN_PB31, 0); /* SPI1_MOSI */ + at91_set_A_periph(AT91_PIN_PB29, 0); /* SPI1_SPCK */ + + at91_clock_associate("spi1_clk", &at91sam9261_spi1_device.dev, "spi_clk"); + platform_device_register(&at91sam9261_spi1_device); + } +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif + + +/* -------------------------------------------------------------------- + * LCD Controller + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_FB_AT91) || defined(CONFIG_FB_AT91_MODULE) +static u64 lcdc_dmamask = 0xffffffffUL; +static struct at91fb_info lcdc_data; + +static struct resource lcdc_resources[] = { + [0] = { + .start = AT91SAM9261_LCDC_BASE, + .end = AT91SAM9261_LCDC_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_LCDC, + .end = AT91SAM9261_ID_LCDC, + .flags = IORESOURCE_IRQ, + }, +#if defined(CONFIG_FB_INTSRAM) + [2] = { + .start = AT91SAM9261_SRAM_BASE, + .end = AT91SAM9261_SRAM_BASE + AT91SAM9261_SRAM_SIZE - 1, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device at91_lcdc_device = { + .name = "at91-fb", + .id = 0, + .dev = { + .dma_mask = &lcdc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &lcdc_data, + }, + .resource = lcdc_resources, + .num_resources = ARRAY_SIZE(lcdc_resources), +}; + +void __init at91_add_device_lcdc(struct at91fb_info *data) +{ + if (!data) { + return; + } + + at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ + at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ + at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ + at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */ + at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */ + at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */ + at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */ + at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */ + at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */ + at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */ + at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */ + at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */ + at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */ + at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */ + at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */ + at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */ + at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */ + at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */ + at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */ + at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */ + at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ + at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ + + lcdc_data = *data; + platform_device_register(&at91_lcdc_device); +} +#else +void __init at91_add_device_lcdc(struct at91fb_info *data) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SERIAL_ATMEL) +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ + .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), +}; + +static struct platform_device at91sam9261_dbgu_device = { + .name = "atmel_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA9, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PA10, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_US0, + .end = AT91SAM9261_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_US0, + .end = AT91SAM9261_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9261_uart0_device = { + .name = "atmel_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC8, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PC9, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */ + at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */ +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_US1, + .end = AT91SAM9261_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_US1, + .end = AT91SAM9261_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9261_uart1_device = { + .name = "atmel_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC12, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PC13, 0); /* RXD1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_US2, + .end = AT91SAM9261_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_US2, + .end = AT91SAM9261_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9261_uart2_device = { + .name = "atmel_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC15, 0); /* RXD2 */ + at91_set_A_periph(AT91_PIN_PC14, 1); /* TXD2 */ +} + +struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ +struct platform_device *atmel_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91sam9261_uart0_device; + at91_clock_associate("usart0_clk", &at91sam9261_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91sam9261_uart1_device; + at91_clock_associate("usart1_clk", &at91sam9261_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91sam9261_uart2_device; + at91_clock_associate("usart2_clk", &at91sam9261_uart2_device.dev, "usart"); + break; + case 3: + configure_dbgu_pins(); + at91_uarts[i] = &at91sam9261_dbgu_device; + at91_clock_associate("mck", &at91sam9261_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < ATMEL_MAX_UART) + atmel_default_console_device = at91_uarts[config->console_tty]; + if (!atmel_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < ATMEL_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ + +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + return 0; +} + +arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c new file mode 100644 index 000000000000..59cbbe1e8161 --- /dev/null +++ b/arch/arm/mach-at91/at91sam926x_time.c @@ -0,0 +1,114 @@ +/* + * linux/arch/arm/mach-at91/at91sam926x_time.c + * + * Copyright (C) 2005-2006 M. Amine SAYA, ATMEL Rousset, France + * Revision 2005 M. Nicolas Diremdjian, ATMEL Rousset, France + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + + +#define PIT_CPIV(x) ((x) & AT91_PIT_CPIV) +#define PIT_PICNT(x) (((x) & AT91_PIT_PICNT) >> 20) + +/* + * Returns number of microseconds since last timer interrupt. Note that interrupts + * will have been disabled by do_gettimeofday() + * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. + * 'tick' is usecs per jiffy (linux/timex.h). + */ +static unsigned long at91sam926x_gettimeoffset(void) +{ + unsigned long elapsed; + unsigned long t = at91_sys_read(AT91_PIT_PIIR); + + elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t); /* hardware clock cycles */ + + return (unsigned long)(elapsed * 1000000) / LATCH; +} + +/* + * IRQ handler for the timer. + */ +static irqreturn_t at91sam926x_timer_interrupt(int irq, void *dev_id) +{ + volatile long nr_ticks; + + if (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS) { /* This is a shared interrupt */ + write_seqlock(&xtime_lock); + + /* Get number to ticks performed before interrupt and clear PIT interrupt */ + nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); + do { + timer_tick(); + nr_ticks--; + } while (nr_ticks); + + write_sequnlock(&xtime_lock); + return IRQ_HANDLED; + } else + return IRQ_NONE; /* not handled */ +} + +static struct irqaction at91sam926x_timer_irq = { + .name = "at91_tick", + .flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER, + .handler = at91sam926x_timer_interrupt +}; + +void at91sam926x_timer_reset(void) +{ + /* Disable timer */ + at91_sys_write(AT91_PIT_MR, 0); + + /* Clear any pending interrupts */ + (void) at91_sys_read(AT91_PIT_PIVR); + + /* Set Period Interval timer and enable its interrupt */ + at91_sys_write(AT91_PIT_MR, (LATCH & AT91_PIT_PIV) | AT91_PIT_PITIEN | AT91_PIT_PITEN); +} + +/* + * Set up timer interrupt. + */ +void __init at91sam926x_timer_init(void) +{ + /* Initialize and enable the timer */ + at91sam926x_timer_reset(); + + /* Make IRQs happen for the system timer. */ + setup_irq(AT91_ID_SYS, &at91sam926x_timer_irq); +} + +#ifdef CONFIG_PM +static void at91sam926x_timer_suspend(void) +{ + /* Disable timer */ + at91_sys_write(AT91_PIT_MR, 0); +} +#else +#define at91sam926x_timer_suspend NULL +#endif + +struct sys_timer at91sam926x_timer = { + .init = at91sam926x_timer_init, + .offset = at91sam926x_gettimeoffset, + .suspend = at91sam926x_timer_suspend, + .resume = at91sam926x_timer_reset, +}; + diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c new file mode 100644 index 000000000000..2d3d4b6f7b02 --- /dev/null +++ b/arch/arm/mach-at91/board-1arm.c @@ -0,0 +1,102 @@ +/* + * linux/arch/arm/mach-at91/board-1arm.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata onearm_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 3, + .tty_map = { 4, 0, 1, -1, -1 }, /* ttyS0, ..., ttyS4 */ +}; + +static void __init onearm_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_PQFP); + + /* Setup the serial ports and console */ + at91_init_serial(&onearm_uart_config); +} + +static void __init onearm_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata onearm_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata onearm_usbh_data = { + .ports = 1, +}; + +static struct at91_udc_data __initdata onearm_udc_data = { + .vbus_pin = AT91_PIN_PC2, + .pullup_pin = AT91_PIN_PC3, +}; + +static void __init onearm_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&onearm_eth_data); + /* USB Host */ + at91_add_device_usbh(&onearm_usbh_data); + /* USB Device */ + at91_add_device_udc(&onearm_udc_data); +} + +MACHINE_START(ONEARM, "Ajeco 1ARM single board computer") + /* Maintainer: Lennert Buytenhek */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = onearm_map_io, + .init_irq = onearm_init_irq, + .init_machine = onearm_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c new file mode 100644 index 000000000000..a0815322f685 --- /dev/null +++ b/arch/arm/mach-at91/board-carmeva.c @@ -0,0 +1,149 @@ +/* + * linux/arch/arm/mach-at91/board-carmeva.c + * + * Copyright (c) 2005 Peer Georgi + * Conitec Datasystems + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata carmeva_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init carmeva_map_io(void) +{ + /* Initialize processor: 20.000 MHz crystal */ + at91rm9200_initialize(20000000, AT91RM9200_BGA); + + /* Setup the serial ports and console */ + at91_init_serial(&carmeva_uart_config); +} + +static void __init carmeva_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata carmeva_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata carmeva_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata carmeva_udc_data = { + .vbus_pin = AT91_PIN_PD12, + .pullup_pin = AT91_PIN_PD9, +}; + +/* FIXME: user dependend */ +// static struct at91_cf_data __initdata carmeva_cf_data = { +// .det_pin = AT91_PIN_PB0, +// .rst_pin = AT91_PIN_PC5, + // .irq_pin = ... not connected + // .vcc_pin = ... always powered +// }; + +static struct at91_mmc_data __initdata carmeva_mmc_data = { + .slot_b = 0, + .wire4 = 1, + .det_pin = AT91_PIN_PB10, + .wp_pin = AT91_PIN_PC14, +}; + +static struct spi_board_info carmeva_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 10 * 1000 * 1000, + }, + { /* User accessable spi - cs1 (250KHz) */ + .modalias = "spi-cs1", + .chip_select = 1, + .max_speed_hz = 250 * 1000, + }, + { /* User accessable spi - cs2 (1MHz) */ + .modalias = "spi-cs2", + .chip_select = 2, + .max_speed_hz = 1 * 1000 * 1000, + }, + { /* User accessable spi - cs3 (10MHz) */ + .modalias = "spi-cs3", + .chip_select = 3, + .max_speed_hz = 10 * 1000 * 1000, + }, +}; + +static void __init carmeva_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&carmeva_eth_data); + /* USB Host */ + at91_add_device_usbh(&carmeva_usbh_data); + /* USB Device */ + at91_add_device_udc(&carmeva_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* SPI */ + at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices)); + /* Compact Flash */ +// at91_add_device_cf(&carmeva_cf_data); + /* MMC */ + at91_add_device_mmc(&carmeva_mmc_data); +} + +MACHINE_START(CARMEVA, "Carmeva") + /* Maintainer: Conitec Datasystems */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = carmeva_map_io, + .init_irq = carmeva_init_irq, + .init_machine = carmeva_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c new file mode 100644 index 000000000000..45d6d9b8f5e9 --- /dev/null +++ b/arch/arm/mach-at91/board-csb337.c @@ -0,0 +1,145 @@ +/* + * linux/arch/arm/mach-at91/board-csb337.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata csb337_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init csb337_map_io(void) +{ + /* Initialize processor: 3.6864 MHz crystal */ + at91rm9200_initialize(3686400, AT91RM9200_BGA); + + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); + + /* Setup the serial ports and console */ + at91_init_serial(&csb337_uart_config); +} + +static void __init csb337_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata csb337_eth_data = { + .phy_irq_pin = AT91_PIN_PC2, + .is_rmii = 0, +}; + +static struct at91_usbh_data __initdata csb337_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata csb337_udc_data = { + // this has no VBUS sensing pin + .pullup_pin = AT91_PIN_PA24, +}; + +static struct at91_cf_data __initdata csb337_cf_data = { + /* + * connector P4 on the CSB 337 mates to + * connector P8 on the CSB 300CF + */ + + /* CSB337 specific */ + .det_pin = AT91_PIN_PC3, + + /* CSB300CF specific */ + .irq_pin = AT91_PIN_PA19, + .vcc_pin = AT91_PIN_PD0, + .rst_pin = AT91_PIN_PD2, +}; + +static struct at91_mmc_data __initdata csb337_mmc_data = { + .det_pin = AT91_PIN_PD5, + .slot_b = 0, + .wire4 = 1, + .wp_pin = AT91_PIN_PD6, +}; + +static struct spi_board_info csb337_spi_devices[] = { + { /* CAN controller */ + .modalias = "sak82c900", + .chip_select = 0, + .max_speed_hz = 6 * 1000 * 1000, + }, +}; + +static void __init csb337_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&csb337_eth_data); + /* USB Host */ + at91_add_device_usbh(&csb337_usbh_data); + /* USB Device */ + at91_add_device_udc(&csb337_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* Compact Flash */ + at91_set_gpio_input(AT91_PIN_PB22, 1); /* IOIS16 */ + at91_add_device_cf(&csb337_cf_data); + /* SPI */ + at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); + /* MMC */ + at91_add_device_mmc(&csb337_mmc_data); +} + +MACHINE_START(CSB337, "Cogent CSB337") + /* Maintainer: Bill Gatliff */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = csb337_map_io, + .init_irq = csb337_init_irq, + .init_machine = csb337_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c new file mode 100644 index 000000000000..774609479c74 --- /dev/null +++ b/arch/arm/mach-at91/board-csb637.c @@ -0,0 +1,109 @@ +/* + * linux/arch/arm/mach-at91/board-csb637.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata csb637_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init csb637_map_io(void) +{ + /* Initialize processor: 3.6864 MHz crystal */ + at91rm9200_initialize(3686400, AT91RM9200_BGA); + + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); + + /* Setup the serial ports and console */ + at91_init_serial(&csb637_uart_config); +} + +static void __init csb637_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata csb637_eth_data = { + .phy_irq_pin = AT91_PIN_PC0, + .is_rmii = 0, +}; + +static struct at91_usbh_data __initdata csb637_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata csb637_udc_data = { + .vbus_pin = AT91_PIN_PB28, + .pullup_pin = AT91_PIN_PB1, +}; + +static void __init csb637_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&csb637_eth_data); + /* USB Host */ + at91_add_device_usbh(&csb637_usbh_data); + /* USB Device */ + at91_add_device_udc(&csb637_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* SPI */ + at91_add_device_spi(NULL, 0); +} + +MACHINE_START(CSB637, "Cogent CSB637") + /* Maintainer: Bill Gatliff */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = csb637_map_io, + .init_irq = csb637_init_irq, + .init_machine = csb637_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-dk.c b/arch/arm/mach-at91/board-dk.c new file mode 100644 index 000000000000..7401dbe1b474 --- /dev/null +++ b/arch/arm/mach-at91/board-dk.c @@ -0,0 +1,216 @@ +/* + * linux/arch/arm/mach-at91/board-dk.c + * + * Copyright (C) 2005 SAN People + * + * Epson S1D framebuffer glue code is: + * Copyright (C) 2005 Thibaut VARENE + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata dk_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init dk_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_BGA); + + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); + + /* Setup the serial ports and console */ + at91_init_serial(&dk_uart_config); +} + +static void __init dk_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata dk_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata dk_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata dk_udc_data = { + .vbus_pin = AT91_PIN_PD4, + .pullup_pin = AT91_PIN_PD5, +}; + +static struct at91_cf_data __initdata dk_cf_data = { + .det_pin = AT91_PIN_PB0, + .rst_pin = AT91_PIN_PC5, + // .irq_pin = ... not connected + // .vcc_pin = ... always powered +}; + +static struct at91_mmc_data __initdata dk_mmc_data = { + .slot_b = 0, + .wire4 = 1, +}; + +static struct spi_board_info dk_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + }, + { /* UR6HCPS2-SP40 PS2-to-SPI adapter */ + .modalias = "ur6hcps2", + .chip_select = 1, + .max_speed_hz = 250 * 1000, + }, + { /* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */ + .modalias = "tlv1504", + .chip_select = 2, + .max_speed_hz = 20 * 1000 * 1000, + }, +#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 3, + .max_speed_hz = 15 * 1000 * 1000, + } +#endif +}; + +static struct mtd_partition __initdata dk_nand_partition[] = { + { + .name = "NAND Partition 1", + .offset = 0, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(dk_nand_partition); + return dk_nand_partition; +} + +static struct at91_nand_data __initdata dk_nand_data = { + .ale = 22, + .cle = 21, + .det_pin = AT91_PIN_PB1, + .rdy_pin = AT91_PIN_PC2, + // .enable_pin = ... not there + .partition_info = nand_partitions, +}; + +#define DK_FLASH_BASE AT91_CHIPSELECT_0 +#define DK_FLASH_SIZE 0x200000 + +static struct physmap_flash_data dk_flash_data = { + .width = 2, +}; + +static struct resource dk_flash_resource = { + .start = DK_FLASH_BASE, + .end = DK_FLASH_BASE + DK_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device dk_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &dk_flash_data, + }, + .resource = &dk_flash_resource, + .num_resources = 1, +}; + + +static void __init dk_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&dk_eth_data); + /* USB Host */ + at91_add_device_usbh(&dk_usbh_data); + /* USB Device */ + at91_add_device_udc(&dk_udc_data); + at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ + /* Compact Flash */ + at91_add_device_cf(&dk_cf_data); + /* I2C */ + at91_add_device_i2c(); + /* SPI */ + at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices)); +#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD + /* DataFlash card */ + at91_set_gpio_output(AT91_PIN_PB7, 0); +#else + /* MMC */ + at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ + at91_add_device_mmc(&dk_mmc_data); +#endif + /* NAND */ + at91_add_device_nand(&dk_nand_data); + /* NOR Flash */ + platform_device_register(&dk_flash); + /* VGA */ +// dk_add_device_video(); +} + +MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK") + /* Maintainer: SAN People/Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = dk_map_io, + .init_irq = dk_init_irq, + .init_machine = dk_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c new file mode 100644 index 000000000000..56d5ef63e04e --- /dev/null +++ b/arch/arm/mach-at91/board-eb9200.c @@ -0,0 +1,123 @@ +/* + * linux/arch/arm/mach-at91/board-eb9200.c + * + * Copyright (C) 2005 SAN People, adapted for ATEB9200 from Embest + * by Andrew Patrikalakis + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata eb9200_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init eb9200_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_BGA); + + /* Setup the serial ports and console */ + at91_init_serial(&eb9200_uart_config); +} + +static void __init eb9200_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata eb9200_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata eb9200_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata eb9200_udc_data = { + .vbus_pin = AT91_PIN_PD4, + .pullup_pin = AT91_PIN_PD5, +}; + +static struct at91_cf_data __initdata eb9200_cf_data = { + .det_pin = AT91_PIN_PB0, + .rst_pin = AT91_PIN_PC5, + // .irq_pin = ... not connected + // .vcc_pin = ... always powered +}; + +static struct at91_mmc_data __initdata eb9200_mmc_data = { + .slot_b = 0, + .wire4 = 1, +}; + +static void __init eb9200_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&eb9200_eth_data); + /* USB Host */ + at91_add_device_usbh(&eb9200_usbh_data); + /* USB Device */ + at91_add_device_udc(&eb9200_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* Compact Flash */ + at91_add_device_cf(&eb9200_cf_data); + /* SPI */ + at91_add_device_spi(NULL, 0); + /* MMC */ + /* only supports 1 or 4 bit interface, not wired through to SPI */ + at91_add_device_mmc(&eb9200_mmc_data); +} + +MACHINE_START(ATEB9200, "Embest ATEB9200") + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = eb9200_map_io, + .init_irq = eb9200_init_irq, + .init_machine = eb9200_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-ek.c new file mode 100644 index 000000000000..0f589dd7d1a9 --- /dev/null +++ b/arch/arm/mach-at91/board-ek.c @@ -0,0 +1,174 @@ +/* + * linux/arch/arm/mach-at91/board-ek.c + * + * Copyright (C) 2005 SAN People + * + * Epson S1D framebuffer glue code is: + * Copyright (C) 2005 Thibaut VARENE + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_BGA); + + /* Setup the LEDs */ + at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata ek_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 1, +}; + +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PD4, + .pullup_pin = AT91_PIN_PD5, +}; + +static struct at91_mmc_data __initdata ek_mmc_data = { + .det_pin = AT91_PIN_PB27, + .slot_b = 0, + .wire4 = 1, + .wp_pin = AT91_PIN_PA17, +}; + +static struct spi_board_info ek_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + }, +#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 3, + .max_speed_hz = 15 * 1000 * 1000, + }, +#endif +}; + +#define EK_FLASH_BASE AT91_CHIPSELECT_0 +#define EK_FLASH_SIZE 0x200000 + +static struct physmap_flash_data ek_flash_data = { + .width = 2, +}; + +static struct resource ek_flash_resource = { + .start = EK_FLASH_BASE, + .end = EK_FLASH_BASE + EK_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device ek_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &ek_flash_data, + }, + .resource = &ek_flash_resource, + .num_resources = 1, +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&ek_eth_data); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ + /* I2C */ + at91_add_device_i2c(); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); +#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD + /* DataFlash card */ + at91_set_gpio_output(AT91_PIN_PB22, 0); +#else + /* MMC */ + at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ + at91_add_device_mmc(&ek_mmc_data); +#endif + /* NOR Flash */ + platform_device_register(&ek_flash); + /* VGA */ +// ek_add_device_video(); +} + +MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") + /* Maintainer: SAN People/Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c new file mode 100644 index 000000000000..c77d84ce9cae --- /dev/null +++ b/arch/arm/mach-at91/board-kafa.c @@ -0,0 +1,109 @@ +/* + * linux/arch/arm/mach-at91/board-kafa.c + * + * Copyright (C) 2006 Sperry-Sun + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata kafa_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init kafa_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_PQFP); + + /* Set up the LEDs */ + at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4); + + /* Setup the serial ports and console */ + at91_init_serial(&kafa_uart_config); +} + +static void __init kafa_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata kafa_eth_data = { + .phy_irq_pin = AT91_PIN_PC4, + .is_rmii = 0, +}; + +static struct at91_usbh_data __initdata kafa_usbh_data = { + .ports = 1, +}; + +static struct at91_udc_data __initdata kafa_udc_data = { + .vbus_pin = AT91_PIN_PB6, + .pullup_pin = AT91_PIN_PB7, +}; + +static void __init kafa_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&kafa_eth_data); + /* USB Host */ + at91_add_device_usbh(&kafa_usbh_data); + /* USB Device */ + at91_add_device_udc(&kafa_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* SPI */ + at91_add_device_spi(NULL, 0); +} + +MACHINE_START(KAFA, "Sperry-Sun KAFA") + /* Maintainer: Sergei Sharonov */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = kafa_map_io, + .init_irq = kafa_init_irq, + .init_machine = kafa_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c new file mode 100644 index 000000000000..17e68f5efb13 --- /dev/null +++ b/arch/arm/mach-at91/board-kb9202.c @@ -0,0 +1,143 @@ +/* + * linux/arch/arm/mach-at91/board-kb9202.c + * + * Copyright (c) 2005 kb_admin + * KwikByte, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata kb9202_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 3, + .tty_map = { 4, 0, 1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init kb9202_map_io(void) +{ + /* Initialize processor: 10 MHz crystal */ + at91rm9200_initialize(10000000, AT91RM9200_PQFP); + + /* Set up the LEDs */ + at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); + + /* Setup the serial ports and console */ + at91_init_serial(&kb9202_uart_config); +} + +static void __init kb9202_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +static struct at91_eth_data __initdata kb9202_eth_data = { + .phy_irq_pin = AT91_PIN_PB29, + .is_rmii = 0, +}; + +static struct at91_usbh_data __initdata kb9202_usbh_data = { + .ports = 1, +}; + +static struct at91_udc_data __initdata kb9202_udc_data = { + .vbus_pin = AT91_PIN_PB24, + .pullup_pin = AT91_PIN_PB22, +}; + +static struct at91_mmc_data __initdata kb9202_mmc_data = { + .det_pin = AT91_PIN_PB2, + .slot_b = 0, + .wire4 = 1, +}; + +static struct mtd_partition __initdata kb9202_nand_partition[] = { + { + .name = "nand_fs", + .offset = 0, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(kb9202_nand_partition); + return kb9202_nand_partition; +} + +static struct at91_nand_data __initdata kb9202_nand_data = { + .ale = 22, + .cle = 21, + // .det_pin = ... not there + .rdy_pin = AT91_PIN_PC29, + .enable_pin = AT91_PIN_PC28, + .partition_info = nand_partitions, +}; + +static void __init kb9202_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* Ethernet */ + at91_add_device_eth(&kb9202_eth_data); + /* USB Host */ + at91_add_device_usbh(&kb9202_usbh_data); + /* USB Device */ + at91_add_device_udc(&kb9202_udc_data); + /* MMC */ + at91_add_device_mmc(&kb9202_mmc_data); + /* I2C */ + at91_add_device_i2c(); + /* SPI */ + at91_add_device_spi(NULL, 0); + /* NAND */ + at91_add_device_nand(&kb9202_nand_data); +} + +MACHINE_START(KB9200, "KB920x") + /* Maintainer: KwikByte, Inc. */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91rm9200_timer, + .map_io = kb9202_map_io, + .init_irq = kb9202_init_irq, + .init_machine = kb9202_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c new file mode 100644 index 000000000000..6ae272d224e5 --- /dev/null +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -0,0 +1,202 @@ +/* + * linux/arch/arm/mach-at91/board-ek.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 5 = USART0 .. USART5 + * 6 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 3, + .tty_map = { 6, 0, 1, -1, -1, -1, -1 } /* ttyS0, ..., ttyS6 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +#if defined(CONFIG_SND_AT73C213) + { /* AT73C213 DAC */ + .modalias = "snd_at73c213", + .chip_select = 0, + .max_speed_hz = 10 * 1000 * 1000, + .bus_num = 1, + }, +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct __initdata at91_eth_data ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = 256 * 1024, + }, + { + .name = "Partition 2", + .offset = 256 * 1024, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, + .wire4 = 1, +// .det_pin = ... not connected +// .wp_pin = ... not connected +// .vcc_pin = ... not connected +}; + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ + at91_add_device_mmc(&ek_mmc_data); +} + +MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c new file mode 100644 index 000000000000..25d626348e6d --- /dev/null +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -0,0 +1,259 @@ +/* + * linux/arch/arm/mach-at91/board-ek.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 2 = USART0 .. USART2 + * 3 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 1, + .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9261_initialize(18432000); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91sam9261_init_interrupts(NULL); +} + + +/* + * DM9000 ethernet device + */ +#if defined(CONFIG_DM9000) +static struct resource at91sam9261_dm9000_resource[] = { + [0] = { + .start = AT91_CHIPSELECT_2, + .end = AT91_CHIPSELECT_2 + 3, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = AT91_CHIPSELECT_2 + 0x44, + .end = AT91_CHIPSELECT_2 + 0xFF, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = AT91_PIN_PC11, + .end = AT91_PIN_PC11, + .flags = IORESOURCE_IRQ + } +}; + +static struct dm9000_plat_data dm9000_platdata = { + .flags = DM9000_PLATF_16BITONLY, +}; + +static struct platform_device at91sam9261_dm9000_device = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(at91sam9261_dm9000_resource), + .resource = at91sam9261_dm9000_resource, + .dev = { + .platform_data = &dm9000_platdata, + } +}; + +static void __init ek_add_device_dm9000(void) +{ + /* + * Configure Chip-Select 2 on SMC for the DM9000. + * Note: These timings were calculated for MASTER_CLOCK = 100000000 + * according to the DM9000 timings. + */ + at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); + at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8)); + at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16)); + at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1)); + + /* Configure Reset signal as output */ + at91_set_gpio_output(AT91_PIN_PC10, 0); + + /* Configure Interrupt pin as input, no pull-up */ + at91_set_gpio_input(AT91_PIN_PC11, 0); + + platform_device_register(&at91sam9261_dm9000_device); +} +#else +static void __init ek_add_device_dm9000(void) {} +#endif /* CONFIG_DM9000 */ + + +/* + * USB Host Port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + + +/* + * USB Device Port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PB29, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .wire4 = 1, +// .det_pin = ... not connected +// .wp_pin = ... not connected +// .vcc_pin = ... not connected +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = 256 * 1024, + }, + { + .name = "Partition 2", + .offset = 256 * 1024 , + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 22, + .cle = 21, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC15, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + +/* + * SPI devices + */ +static struct spi_board_info ek_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card - jumper (J12) configurable to CS3 or CS0 */ + .modalias = "mtd_dataflash", + .chip_select = 3, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#elif defined(CONFIG_SND_AT73C213) + { /* AT73C213 DAC */ + .modalias = "snd_at73c213", + .chip_select = 3, + .max_speed_hz = 10 * 1000 * 1000, + .bus_num = 0, + }, +#endif +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* DM9000 ethernet */ + ek_add_device_dm9000(); + + /* spi0 and mmc/sd share the same PIO pins */ +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); +#else + /* MMC */ + at91_add_device_mmc(&ek_mmc_data); +#endif +} + +MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c new file mode 100644 index 000000000000..baab095f6e32 --- /dev/null +++ b/arch/arm/mach-at91/clock.c @@ -0,0 +1,644 @@ +/* + * linux/arch/arm/mach-at91/clock.c + * + * Copyright (C) 2005 David Brownell + * Copyright (C) 2005 Ivan Kokshaysky + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "clock.h" + + +/* + * There's a lot more which can be done with clocks, including cpufreq + * integration, slow clock mode support (for system suspend), letting + * PLLB be used at other rates (on boards that don't need USB), etc. + */ + +#define clk_is_primary(x) ((x)->type & CLK_TYPE_PRIMARY) +#define clk_is_programmable(x) ((x)->type & CLK_TYPE_PROGRAMMABLE) +#define clk_is_peripheral(x) ((x)->type & CLK_TYPE_PERIPHERAL) +#define clk_is_sys(x) ((x)->type & CLK_TYPE_SYSTEM) + + +static LIST_HEAD(clocks); +static DEFINE_SPINLOCK(clk_lock); + +static u32 at91_pllb_usb_init; + +/* + * Four primary clock sources: two crystal oscillators (32K, main), and + * two PLLs. PLLA usually runs the master clock; and PLLB must run at + * 48 MHz (unless no USB function clocks are needed). The main clock and + * both PLLs are turned off to run in "slow clock mode" (system suspend). + */ +static struct clk clk32k = { + .name = "clk32k", + .rate_hz = AT91_SLOW_CLOCK, + .users = 1, /* always on */ + .id = 0, + .type = CLK_TYPE_PRIMARY, +}; +static struct clk main_clk = { + .name = "main", + .pmc_mask = AT91_PMC_MOSCS, /* in PMC_SR */ + .id = 1, + .type = CLK_TYPE_PRIMARY, +}; +static struct clk plla = { + .name = "plla", + .parent = &main_clk, + .pmc_mask = AT91_PMC_LOCKA, /* in PMC_SR */ + .id = 2, + .type = CLK_TYPE_PRIMARY | CLK_TYPE_PLL, +}; + +static void pllb_mode(struct clk *clk, int is_on) +{ + u32 value; + + if (is_on) { + is_on = AT91_PMC_LOCKB; + value = at91_pllb_usb_init; + } else + value = 0; + + // REVISIT: Add work-around for AT91RM9200 Errata #26 ? + at91_sys_write(AT91_CKGR_PLLBR, value); + + do { + cpu_relax(); + } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on); +} + +static struct clk pllb = { + .name = "pllb", + .parent = &main_clk, + .pmc_mask = AT91_PMC_LOCKB, /* in PMC_SR */ + .mode = pllb_mode, + .id = 3, + .type = CLK_TYPE_PRIMARY | CLK_TYPE_PLL, +}; + +static void pmc_sys_mode(struct clk *clk, int is_on) +{ + if (is_on) + at91_sys_write(AT91_PMC_SCER, clk->pmc_mask); + else + at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask); +} + +/* USB function clocks (PLLB must be 48 MHz) */ +static struct clk udpck = { + .name = "udpck", + .parent = &pllb, + .mode = pmc_sys_mode, +}; +static struct clk uhpck = { + .name = "uhpck", + .parent = &pllb, + .mode = pmc_sys_mode, +}; + + +/* + * The master clock is divided from the CPU clock (by 1-4). It's used for + * memory, interfaces to on-chip peripherals, the AIC, and sometimes more + * (e.g baud rate generation). It's sourced from one of the primary clocks. + */ +static struct clk mck = { + .name = "mck", + .pmc_mask = AT91_PMC_MCKRDY, /* in PMC_SR */ +}; + +static void pmc_periph_mode(struct clk *clk, int is_on) +{ + if (is_on) + at91_sys_write(AT91_PMC_PCER, clk->pmc_mask); + else + at91_sys_write(AT91_PMC_PCDR, clk->pmc_mask); +} + +static struct clk __init *at91_css_to_clk(unsigned long css) +{ + switch (css) { + case AT91_PMC_CSS_SLOW: + return &clk32k; + case AT91_PMC_CSS_MAIN: + return &main_clk; + case AT91_PMC_CSS_PLLA: + return &plla; + case AT91_PMC_CSS_PLLB: + return &pllb; + } + + return NULL; +} + +/* + * Associate a particular clock with a function (eg, "uart") and device. + * The drivers can then request the same 'function' with several different + * devices and not care about which clock name to use. + */ +void __init at91_clock_associate(const char *id, struct device *dev, const char *func) +{ + struct clk *clk = clk_get(NULL, id); + + if (!dev || !clk || !IS_ERR(clk_get(dev, func))) + return; + + clk->function = func; + clk->dev = dev; +} + +/* clocks cannot be de-registered no refcounting necessary */ +struct clk *clk_get(struct device *dev, const char *id) +{ + struct clk *clk; + + list_for_each_entry(clk, &clocks, node) { + if (strcmp(id, clk->name) == 0) + return clk; + if (clk->function && (dev == clk->dev) && strcmp(id, clk->function) == 0) + return clk; + } + + return ERR_PTR(-ENOENT); +} +EXPORT_SYMBOL(clk_get); + +void clk_put(struct clk *clk) +{ +} +EXPORT_SYMBOL(clk_put); + +static void __clk_enable(struct clk *clk) +{ + if (clk->parent) + __clk_enable(clk->parent); + if (clk->users++ == 0 && clk->mode) + clk->mode(clk, 1); +} + +int clk_enable(struct clk *clk) +{ + unsigned long flags; + + spin_lock_irqsave(&clk_lock, flags); + __clk_enable(clk); + spin_unlock_irqrestore(&clk_lock, flags); + return 0; +} +EXPORT_SYMBOL(clk_enable); + +static void __clk_disable(struct clk *clk) +{ + BUG_ON(clk->users == 0); + if (--clk->users == 0 && clk->mode) + clk->mode(clk, 0); + if (clk->parent) + __clk_disable(clk->parent); +} + +void clk_disable(struct clk *clk) +{ + unsigned long flags; + + spin_lock_irqsave(&clk_lock, flags); + __clk_disable(clk); + spin_unlock_irqrestore(&clk_lock, flags); +} +EXPORT_SYMBOL(clk_disable); + +unsigned long clk_get_rate(struct clk *clk) +{ + unsigned long flags; + unsigned long rate; + + spin_lock_irqsave(&clk_lock, flags); + for (;;) { + rate = clk->rate_hz; + if (rate || !clk->parent) + break; + clk = clk->parent; + } + spin_unlock_irqrestore(&clk_lock, flags); + return rate; +} +EXPORT_SYMBOL(clk_get_rate); + +/*------------------------------------------------------------------------*/ + +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS + +/* + * For now, only the programmable clocks support reparenting (MCK could + * do this too, with care) or rate changing (the PLLs could do this too, + * ditto MCK but that's more for cpufreq). Drivers may reparent to get + * a better rate match; we don't. + */ + +long clk_round_rate(struct clk *clk, unsigned long rate) +{ + unsigned long flags; + unsigned prescale; + unsigned long actual; + + if (!clk_is_programmable(clk)) + return -EINVAL; + spin_lock_irqsave(&clk_lock, flags); + + actual = clk->parent->rate_hz; + for (prescale = 0; prescale < 7; prescale++) { + if (actual && actual <= rate) + break; + actual >>= 1; + } + + spin_unlock_irqrestore(&clk_lock, flags); + return (prescale < 7) ? actual : -ENOENT; +} +EXPORT_SYMBOL(clk_round_rate); + +int clk_set_rate(struct clk *clk, unsigned long rate) +{ + unsigned long flags; + unsigned prescale; + unsigned long actual; + + if (!clk_is_programmable(clk)) + return -EINVAL; + if (clk->users) + return -EBUSY; + spin_lock_irqsave(&clk_lock, flags); + + actual = clk->parent->rate_hz; + for (prescale = 0; prescale < 7; prescale++) { + if (actual && actual <= rate) { + u32 pckr; + + pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); + pckr &= AT91_PMC_CSS_PLLB; /* clock selection */ + pckr |= prescale << 2; + at91_sys_write(AT91_PMC_PCKR(clk->id), pckr); + clk->rate_hz = actual; + break; + } + actual >>= 1; + } + + spin_unlock_irqrestore(&clk_lock, flags); + return (prescale < 7) ? actual : -ENOENT; +} +EXPORT_SYMBOL(clk_set_rate); + +struct clk *clk_get_parent(struct clk *clk) +{ + return clk->parent; +} +EXPORT_SYMBOL(clk_get_parent); + +int clk_set_parent(struct clk *clk, struct clk *parent) +{ + unsigned long flags; + + if (clk->users) + return -EBUSY; + if (!clk_is_primary(parent) || !clk_is_programmable(clk)) + return -EINVAL; + spin_lock_irqsave(&clk_lock, flags); + + clk->rate_hz = parent->rate_hz; + clk->parent = parent; + at91_sys_write(AT91_PMC_PCKR(clk->id), parent->id); + + spin_unlock_irqrestore(&clk_lock, flags); + return 0; +} +EXPORT_SYMBOL(clk_set_parent); + +/* establish PCK0..PCK3 parentage and rate */ +static void init_programmable_clock(struct clk *clk) +{ + struct clk *parent; + u32 pckr; + + pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); + parent = at91_css_to_clk(pckr & AT91_PMC_CSS); + clk->parent = parent; + clk->rate_hz = parent->rate_hz / (1 << ((pckr >> 2) & 3)); +} + +#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ + +/*------------------------------------------------------------------------*/ + +#ifdef CONFIG_DEBUG_FS + +static int at91_clk_show(struct seq_file *s, void *unused) +{ + u32 scsr, pcsr, sr; + struct clk *clk; + unsigned i; + + seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR)); + seq_printf(s, "PCSR = %8x\n", pcsr = at91_sys_read(AT91_PMC_PCSR)); + + seq_printf(s, "MOR = %8x\n", at91_sys_read(AT91_CKGR_MOR)); + seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR)); + seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR)); + seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); + + seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR)); + for (i = 0; i < 4; i++) + seq_printf(s, "PCK%d = %8x\n", i, at91_sys_read(AT91_PMC_PCKR(i))); + seq_printf(s, "SR = %8x\n", sr = at91_sys_read(AT91_PMC_SR)); + + seq_printf(s, "\n"); + + list_for_each_entry(clk, &clocks, node) { + char *state; + + if (clk->mode == pmc_sys_mode) + state = (scsr & clk->pmc_mask) ? "on" : "off"; + else if (clk->mode == pmc_periph_mode) + state = (pcsr & clk->pmc_mask) ? "on" : "off"; + else if (clk->pmc_mask) + state = (sr & clk->pmc_mask) ? "on" : "off"; + else if (clk == &clk32k || clk == &main_clk) + state = "on"; + else + state = ""; + + seq_printf(s, "%-10s users=%2d %-3s %9ld Hz %s\n", + clk->name, clk->users, state, clk_get_rate(clk), + clk->parent ? clk->parent->name : ""); + } + return 0; +} + +static int at91_clk_open(struct inode *inode, struct file *file) +{ + return single_open(file, at91_clk_show, NULL); +} + +static struct file_operations at91_clk_operations = { + .open = at91_clk_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; + +static int __init at91_clk_debugfs_init(void) +{ + /* /sys/kernel/debug/at91_clk */ + (void) debugfs_create_file("at91_clk", S_IFREG | S_IRUGO, NULL, NULL, &at91_clk_operations); + + return 0; +} +postcore_initcall(at91_clk_debugfs_init); + +#endif + +/*------------------------------------------------------------------------*/ + +/* Register a new clock */ +int __init clk_register(struct clk *clk) +{ + if (clk_is_peripheral(clk)) { + clk->parent = &mck; + clk->mode = pmc_periph_mode; + list_add_tail(&clk->node, &clocks); + } + else if (clk_is_sys(clk)) { + clk->parent = &mck; + clk->mode = pmc_sys_mode; + + list_add_tail(&clk->node, &clocks); + } +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS + else if (clk_is_programmable(clk)) { + clk->mode = pmc_sys_mode; + init_programmable_clock(clk); + list_add_tail(&clk->node, &clocks); + } +#endif + + return 0; +} + + +/*------------------------------------------------------------------------*/ + +static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg) +{ + unsigned mul, div; + + div = reg & 0xff; + mul = (reg >> 16) & 0x7ff; + if (div && mul) { + freq /= div; + freq *= mul + 1; + } else + freq = 0; + + return freq; +} + +static u32 __init at91_usb_rate(struct clk *pll, u32 freq, u32 reg) +{ + if (pll == &pllb && (reg & AT91_PMC_USB96M)) + return freq / 2; + else + return freq; +} + +static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq) +{ + unsigned i, div = 0, mul = 0, diff = 1 << 30; + unsigned ret = (out_freq > 155000000) ? 0xbe00 : 0x3e00; + + /* PLL output max 240 MHz (or 180 MHz per errata) */ + if (out_freq > 240000000) + goto fail; + + for (i = 1; i < 256; i++) { + int diff1; + unsigned input, mul1; + + /* + * PLL input between 1MHz and 32MHz per spec, but lower + * frequences seem necessary in some cases so allow 100K. + */ + input = main_freq / i; + if (input < 100000) + continue; + if (input > 32000000) + continue; + + mul1 = out_freq / input; + if (mul1 > 2048) + continue; + if (mul1 < 2) + goto fail; + + diff1 = out_freq - input * mul1; + if (diff1 < 0) + diff1 = -diff1; + if (diff > diff1) { + diff = diff1; + div = i; + mul = mul1; + if (diff == 0) + break; + } + } + if (i == 256 && diff > (out_freq >> 5)) + goto fail; + return ret | ((mul - 1) << 16) | div; +fail: + return 0; +} + +/* + * Several unused clocks may be active. Turn them off. + */ +static void __init at91_periphclk_reset(void) +{ + unsigned long reg; + struct clk *clk; + + reg = at91_sys_read(AT91_PMC_PCSR); + + list_for_each_entry(clk, &clocks, node) { + if (clk->mode != pmc_periph_mode) + continue; + + if (clk->users > 0) + reg &= ~clk->pmc_mask; + } + + at91_sys_write(AT91_PMC_PCDR, reg); +} + +static struct clk *const standard_pmc_clocks[] __initdata = { + /* four primary clocks */ + &clk32k, + &main_clk, + &plla, + &pllb, + + /* PLLB children (USB) */ + &udpck, + &uhpck, + + /* MCK */ + &mck +}; + +int __init at91_clock_init(unsigned long main_clock) +{ + unsigned tmp, freq, mckr; + int i; + + /* + * When the bootloader initialized the main oscillator correctly, + * there's no problem using the cycle counter. But if it didn't, + * or when using oscillator bypass mode, we must be told the speed + * of the main clock. + */ + if (!main_clock) { + do { + tmp = at91_sys_read(AT91_CKGR_MCFR); + } while (!(tmp & AT91_PMC_MAINRDY)); + main_clock = (tmp & AT91_PMC_MAINF) * (AT91_SLOW_CLOCK / 16); + } + main_clk.rate_hz = main_clock; + + /* report if PLLA is more than mildly overclocked */ + plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR)); + if (plla.rate_hz > 209000000) + pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); + + /* + * USB clock init: choose 48 MHz PLLB value, turn all clocks off, + * disable 48MHz clock during usb peripheral suspend. + * + * REVISIT: assumes MCK doesn't derive from PLLB! + */ + at91_pllb_usb_init = at91_pll_calc(main_clock, 48000000 * 2) | AT91_PMC_USB96M; + pllb.rate_hz = at91_pll_rate(&pllb, main_clock, at91_pllb_usb_init); + if (cpu_is_at91rm9200()) { + uhpck.pmc_mask = AT91RM9200_PMC_UHP; + udpck.pmc_mask = AT91RM9200_PMC_UDP; + at91_sys_write(AT91_PMC_SCDR, AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP); + at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); + } else if (cpu_is_at91sam9260()) { + uhpck.pmc_mask = AT91SAM926x_PMC_UHP; + udpck.pmc_mask = AT91SAM926x_PMC_UDP; + at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP); + } else if (cpu_is_at91sam9261()) { + uhpck.pmc_mask = (AT91SAM926x_PMC_UHP | AT91_PMC_HCK0); + udpck.pmc_mask = AT91SAM926x_PMC_UDP; + at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91_PMC_HCK0 | AT91SAM926x_PMC_UDP); + } + at91_sys_write(AT91_CKGR_PLLBR, 0); + + udpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init); + uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init); + + /* + * MCK and CPU derive from one of those primary clocks. + * For now, assume this parentage won't change. + */ + mckr = at91_sys_read(AT91_PMC_MCKR); + mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS); + freq = mck.parent->rate_hz; + freq /= (1 << ((mckr >> 2) & 3)); /* prescale */ + mck.rate_hz = freq / (1 + ((mckr >> 8) & 3)); /* mdiv */ + + /* Register the PMC's standard clocks */ + for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) + list_add_tail(&standard_pmc_clocks[i]->node, &clocks); + + /* MCK and CPU clock are "always on" */ + clk_enable(&mck); + + printk("Clocks: CPU %u MHz, master %u MHz, main %u.%03u MHz\n", + freq / 1000000, (unsigned) mck.rate_hz / 1000000, + (unsigned) main_clock / 1000000, + ((unsigned) main_clock % 1000000) / 1000); + + /* disable all programmable clocks */ + at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK0 | AT91_PMC_PCK1 | AT91_PMC_PCK2 | AT91_PMC_PCK3); + + /* disable all other unused peripheral clocks */ + at91_periphclk_reset(); + + return 0; +} diff --git a/arch/arm/mach-at91/clock.h b/arch/arm/mach-at91/clock.h new file mode 100644 index 000000000000..1ba3b95ff359 --- /dev/null +++ b/arch/arm/mach-at91/clock.h @@ -0,0 +1,31 @@ +/* + * linux/arch/arm/mach-at91/clock.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define CLK_TYPE_PRIMARY 0x1 +#define CLK_TYPE_PLL 0x2 +#define CLK_TYPE_PROGRAMMABLE 0x4 +#define CLK_TYPE_PERIPHERAL 0x8 +#define CLK_TYPE_SYSTEM 0x10 + + +struct clk { + struct list_head node; + const char *name; /* unique clock name */ + const char *function; /* function of the clock */ + struct device *dev; /* device associated with function */ + unsigned long rate_hz; + struct clk *parent; + u32 pmc_mask; + void (*mode)(struct clk *, int); + unsigned id:2; /* PCK0..3, or 32k/main/a/b */ + unsigned type; /* clock type */ + u16 users; +}; + + +extern int __init clk_register(struct clk *clk); diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h new file mode 100644 index 000000000000..10ee37bf6d4d --- /dev/null +++ b/arch/arm/mach-at91/generic.h @@ -0,0 +1,49 @@ +/* + * linux/arch/arm/mach-at91/generic.h + * + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + /* Processors */ +extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks); +extern void __init at91sam9260_initialize(unsigned long main_clock); +extern void __init at91sam9261_initialize(unsigned long main_clock); + + /* Interrupts */ +extern void __init at91rm9200_init_interrupts(unsigned int priority[]); +extern void __init at91sam9260_init_interrupts(unsigned int priority[]); +extern void __init at91sam9261_init_interrupts(unsigned int priority[]); +extern void __init at91_aic_init(unsigned int priority[]); + + /* Timer */ +struct sys_timer; +extern struct sys_timer at91rm9200_timer; +extern struct sys_timer at91sam926x_timer; + + /* Clocks */ +extern int __init at91_clock_init(unsigned long main_clock); +struct device; +extern void __init at91_clock_associate(const char *id, struct device *dev, const char *func); + + /* Power Management */ +extern void at91_irq_suspend(void); +extern void at91_irq_resume(void); + + /* GPIO */ +#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */ +#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */ + +struct at91_gpio_bank { + unsigned short id; /* peripheral ID */ + unsigned long offset; /* offset from system peripheral base */ + struct clk *clock; /* associated clock */ +}; +extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks); +extern void __init at91_gpio_irq_setup(void); + +extern void (*at91_arch_reset)(void); +extern int at91_extern_irq; diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c new file mode 100644 index 000000000000..9b7495cd555d --- /dev/null +++ b/arch/arm/mach-at91/gpio.c @@ -0,0 +1,414 @@ +/* + * linux/arch/arm/mach-at91/gpio.c + * + * Copyright (C) 2005 HP Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include "generic.h" + + +static struct at91_gpio_bank *gpio; +static int gpio_banks; + + +static inline void __iomem *pin_to_controller(unsigned pin) +{ + void __iomem *sys_base = (void __iomem *) AT91_VA_BASE_SYS; + + pin -= PIN_BASE; + pin /= 32; + if (likely(pin < gpio_banks)) + return sys_base + gpio[pin].offset; + + return NULL; +} + +static inline unsigned pin_to_mask(unsigned pin) +{ + pin -= PIN_BASE; + return 1 << (pin % 32); +} + + +/*--------------------------------------------------------------------------*/ + +/* Not all hardware capabilities are exposed through these calls; they + * only encapsulate the most common features and modes. (So if you + * want to change signals in groups, do it directly.) + * + * Bootloaders will usually handle some of the pin multiplexing setup. + * The intent is certainly that by the time Linux is fully booted, all + * pins should have been fully initialized. These setup calls should + * only be used by board setup routines, or possibly in driver probe(). + * + * For bootloaders doing all that setup, these calls could be inlined + * as NOPs so Linux won't duplicate any setup code + */ + + +/* + * mux the pin to the "A" internal peripheral role. + */ +int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(mask, pio + PIO_ASR); + __raw_writel(mask, pio + PIO_PDR); + return 0; +} +EXPORT_SYMBOL(at91_set_A_periph); + + +/* + * mux the pin to the "B" internal peripheral role. + */ +int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(mask, pio + PIO_BSR); + __raw_writel(mask, pio + PIO_PDR); + return 0; +} +EXPORT_SYMBOL(at91_set_B_periph); + + +/* + * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and + * configure it for an input. + */ +int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(mask, pio + PIO_ODR); + __raw_writel(mask, pio + PIO_PER); + return 0; +} +EXPORT_SYMBOL(at91_set_gpio_input); + + +/* + * mux the pin to the gpio controller (instead of "A" or "B" peripheral), + * and configure it for an output. + */ +int __init_or_module at91_set_gpio_output(unsigned pin, int value) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + PIO_PUDR); + __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); + __raw_writel(mask, pio + PIO_OER); + __raw_writel(mask, pio + PIO_PER); + return 0; +} +EXPORT_SYMBOL(at91_set_gpio_output); + + +/* + * enable/disable the glitch filter; mostly used with IRQ handling. + */ +int __init_or_module at91_set_deglitch(unsigned pin, int is_on) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + __raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR)); + return 0; +} +EXPORT_SYMBOL(at91_set_deglitch); + +/* + * enable/disable the multi-driver; This is only valid for output and + * allows the output pin to run as an open collector output. + */ +int __init_or_module at91_set_multi_drive(unsigned pin, int is_on) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR)); + return 0; +} +EXPORT_SYMBOL(at91_set_multi_drive); + +/*--------------------------------------------------------------------------*/ + +/* + * assuming the pin is muxed as a gpio output, set its value. + */ +int at91_set_gpio_value(unsigned pin, int value) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); + return 0; +} +EXPORT_SYMBOL(at91_set_gpio_value); + + +/* + * read the pin's value (works even if it's not muxed as a gpio). + */ +int at91_get_gpio_value(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + u32 pdsr; + + if (!pio) + return -EINVAL; + pdsr = __raw_readl(pio + PIO_PDSR); + return (pdsr & mask) != 0; +} +EXPORT_SYMBOL(at91_get_gpio_value); + +/*--------------------------------------------------------------------------*/ + +#ifdef CONFIG_PM + +static u32 wakeups[MAX_GPIO_BANKS]; +static u32 backups[MAX_GPIO_BANKS]; + +static int gpio_irq_set_wake(unsigned pin, unsigned state) +{ + unsigned mask = pin_to_mask(pin); + unsigned bank = (pin - PIN_BASE) / 32; + + if (unlikely(bank >= MAX_GPIO_BANKS)) + return -EINVAL; + + if (state) + wakeups[bank] |= mask; + else + wakeups[bank] &= ~mask; + + set_irq_wake(gpio[bank].id, state); + + return 0; +} + +void at91_gpio_suspend(void) +{ + int i; + + for (i = 0; i < gpio_banks; i++) { + u32 pio = gpio[i].offset; + + backups[i] = at91_sys_read(pio + PIO_IMR); + at91_sys_write(pio + PIO_IDR, backups[i]); + at91_sys_write(pio + PIO_IER, wakeups[i]); + + if (!wakeups[i]) + clk_disable(gpio[i].clock); + else { +#ifdef CONFIG_PM_DEBUG + printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]); +#endif + } + } +} + +void at91_gpio_resume(void) +{ + int i; + + for (i = 0; i < gpio_banks; i++) { + u32 pio = gpio[i].offset; + + if (!wakeups[i]) + clk_enable(gpio[i].clock); + + at91_sys_write(pio + PIO_IDR, wakeups[i]); + at91_sys_write(pio + PIO_IER, backups[i]); + } +} + +#else +#define gpio_irq_set_wake NULL +#endif + + +/* Several AIC controller irqs are dispatched through this GPIO handler. + * To use any AT91_PIN_* as an externally triggered IRQ, first call + * at91_set_gpio_input() then maybe enable its glitch filter. + * Then just request_irq() with the pin ID; it works like any ARM IRQ + * handler, though it always triggers on rising and falling edges. + * + * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after + * configuring them with at91_set_a_periph() or at91_set_b_periph(). + * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering. + */ + +static void gpio_irq_mask(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (pio) + __raw_writel(mask, pio + PIO_IDR); +} + +static void gpio_irq_unmask(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (pio) + __raw_writel(mask, pio + PIO_IER); +} + +static int gpio_irq_type(unsigned pin, unsigned type) +{ + return (type == IRQT_BOTHEDGE) ? 0 : -EINVAL; +} + +static struct irq_chip gpio_irqchip = { + .name = "GPIO", + .mask = gpio_irq_mask, + .unmask = gpio_irq_unmask, + .set_type = gpio_irq_type, + .set_wake = gpio_irq_set_wake, +}; + +static void gpio_irq_handler(unsigned irq, struct irq_desc *desc) +{ + unsigned pin; + struct irq_desc *gpio; + void __iomem *pio; + u32 isr; + + pio = get_irq_chip_data(irq); + + /* temporarily mask (level sensitive) parent IRQ */ + desc->chip->ack(irq); + for (;;) { + /* reading ISR acks the pending (edge triggered) GPIO interrupt */ + isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR); + if (!isr) + break; + + pin = (unsigned) get_irq_data(irq); + gpio = &irq_desc[pin]; + + while (isr) { + if (isr & 1) { + if (unlikely(gpio->depth)) { + /* + * The core ARM interrupt handler lazily disables IRQs so + * another IRQ must be generated before it actually gets + * here to be disabled on the GPIO controller. + */ + gpio_irq_mask(pin); + } + else + desc_handle_irq(pin, gpio); + } + pin++; + gpio++; + isr >>= 1; + } + } + desc->chip->unmask(irq); + /* now it may re-trigger */ +} + +/*--------------------------------------------------------------------------*/ + +/* + * Called from the processor-specific init to enable GPIO interrupt support. + */ +void __init at91_gpio_irq_setup(void) +{ + unsigned pioc, pin; + + for (pioc = 0, pin = PIN_BASE; + pioc < gpio_banks; + pioc++) { + void __iomem *controller; + unsigned id = gpio[pioc].id; + unsigned i; + + clk_enable(gpio[pioc].clock); /* enable PIO controller's clock */ + + controller = (void __iomem *) AT91_VA_BASE_SYS + gpio[pioc].offset; + __raw_writel(~0, controller + PIO_IDR); + + set_irq_data(id, (void *) pin); + set_irq_chip_data(id, controller); + + for (i = 0; i < 32; i++, pin++) { + /* + * Can use the "simple" and not "edge" handler since it's + * shorter, and the AIC handles interupts sanely. + */ + set_irq_chip(pin, &gpio_irqchip); + set_irq_handler(pin, handle_simple_irq); + set_irq_flags(pin, IRQF_VALID); + } + + set_irq_chained_handler(id, gpio_irq_handler); + } + pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks); +} + +/* + * Called from the processor-specific init to enable GPIO pin support. + */ +void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks) +{ + BUG_ON(nr_banks > MAX_GPIO_BANKS); + + gpio = data; + gpio_banks = nr_banks; +} diff --git a/arch/arm/mach-at91/irq.c b/arch/arm/mach-at91/irq.c new file mode 100644 index 000000000000..78a5cdb746dc --- /dev/null +++ b/arch/arm/mach-at91/irq.c @@ -0,0 +1,168 @@ +/* + * linux/arch/arm/mach-at91/irq.c + * + * Copyright (C) 2004 SAN People + * Copyright (C) 2004 ATMEL + * Copyright (C) Rick Bronson + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + + +static void at91_aic_mask_irq(unsigned int irq) +{ + /* Disable interrupt on AIC */ + at91_sys_write(AT91_AIC_IDCR, 1 << irq); +} + +static void at91_aic_unmask_irq(unsigned int irq) +{ + /* Enable interrupt on AIC */ + at91_sys_write(AT91_AIC_IECR, 1 << irq); +} + +unsigned int at91_extern_irq; + +#define is_extern_irq(irq) ((1 << (irq)) & at91_extern_irq) + +static int at91_aic_set_type(unsigned irq, unsigned type) +{ + unsigned int smr, srctype; + + switch (type) { + case IRQT_HIGH: + srctype = AT91_AIC_SRCTYPE_HIGH; + break; + case IRQT_RISING: + srctype = AT91_AIC_SRCTYPE_RISING; + break; + case IRQT_LOW: + if ((irq == AT91_ID_FIQ) || is_extern_irq(irq)) /* only supported on external interrupts */ + srctype = AT91_AIC_SRCTYPE_LOW; + else + return -EINVAL; + break; + case IRQT_FALLING: + if ((irq == AT91_ID_FIQ) || is_extern_irq(irq)) /* only supported on external interrupts */ + srctype = AT91_AIC_SRCTYPE_FALLING; + else + return -EINVAL; + break; + default: + return -EINVAL; + } + + smr = at91_sys_read(AT91_AIC_SMR(irq)) & ~AT91_AIC_SRCTYPE; + at91_sys_write(AT91_AIC_SMR(irq), smr | srctype); + return 0; +} + +#ifdef CONFIG_PM + +static u32 wakeups; +static u32 backups; + +static int at91_aic_set_wake(unsigned irq, unsigned value) +{ + if (unlikely(irq >= 32)) + return -EINVAL; + + if (value) + wakeups |= (1 << irq); + else + wakeups &= ~(1 << irq); + + return 0; +} + +void at91_irq_suspend(void) +{ + backups = at91_sys_read(AT91_AIC_IMR); + at91_sys_write(AT91_AIC_IDCR, backups); + at91_sys_write(AT91_AIC_IECR, wakeups); +} + +void at91_irq_resume(void) +{ + at91_sys_write(AT91_AIC_IDCR, wakeups); + at91_sys_write(AT91_AIC_IECR, backups); +} + +#else +#define at91_aic_set_wake NULL +#endif + +static struct irq_chip at91_aic_chip = { + .name = "AIC", + .ack = at91_aic_mask_irq, + .mask = at91_aic_mask_irq, + .unmask = at91_aic_unmask_irq, + .set_type = at91_aic_set_type, + .set_wake = at91_aic_set_wake, +}; + +/* + * Initialize the AIC interrupt controller. + */ +void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS]) +{ + unsigned int i; + + /* + * The IVR is used by macro get_irqnr_and_base to read and verify. + * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred. + */ + for (i = 0; i < NR_AIC_IRQS; i++) { + /* Put irq number in Source Vector Register: */ + at91_sys_write(AT91_AIC_SVR(i), i); + /* Active Low interrupt, with the specified priority */ + at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]); + + set_irq_chip(i, &at91_aic_chip); + set_irq_handler(i, handle_level_irq); + set_irq_flags(i, IRQF_VALID | IRQF_PROBE); + + /* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */ + if (i < 8) + at91_sys_write(AT91_AIC_EOICR, 0); + } + + /* + * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS + * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU + */ + at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS); + + /* No debugging in AIC: Debug (Protect) Control Register */ + at91_sys_write(AT91_AIC_DCR, 0); + + /* Disable and clear all interrupts initially */ + at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF); + at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF); +} diff --git a/arch/arm/mach-at91/leds.c b/arch/arm/mach-at91/leds.c new file mode 100644 index 000000000000..1a333730466e --- /dev/null +++ b/arch/arm/mach-at91/leds.c @@ -0,0 +1,99 @@ +/* + * LED driver for Atmel AT91-based boards. + * + * Copyright (C) SAN People (Pty) Ltd + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. +*/ + +#include +#include +#include + +#include +#include +#include +#include + + +static inline void at91_led_on(unsigned int led) +{ + at91_set_gpio_value(led, 0); +} + +static inline void at91_led_off(unsigned int led) +{ + at91_set_gpio_value(led, 1); +} + +static inline void at91_led_toggle(unsigned int led) +{ + unsigned long is_off = at91_get_gpio_value(led); + if (is_off) + at91_led_on(led); + else + at91_led_off(led); +} + + +/* + * Handle LED events. + */ +static void at91_leds_event(led_event_t evt) +{ + unsigned long flags; + + local_irq_save(flags); + + switch(evt) { + case led_start: /* System startup */ + at91_led_on(at91_leds_cpu); + break; + + case led_stop: /* System stop / suspend */ + at91_led_off(at91_leds_cpu); + break; + +#ifdef CONFIG_LEDS_TIMER + case led_timer: /* Every 50 timer ticks */ + at91_led_toggle(at91_leds_timer); + break; +#endif + +#ifdef CONFIG_LEDS_CPU + case led_idle_start: /* Entering idle state */ + at91_led_off(at91_leds_cpu); + break; + + case led_idle_end: /* Exit idle state */ + at91_led_on(at91_leds_cpu); + break; +#endif + + default: + break; + } + + local_irq_restore(flags); +} + + +static int __init leds_init(void) +{ + if (!at91_leds_timer || !at91_leds_cpu) + return -ENODEV; + + /* Enable PIO to access the LEDs */ + at91_set_gpio_output(at91_leds_timer, 1); + at91_set_gpio_output(at91_leds_cpu, 1); + + leds_event = at91_leds_event; + + leds_event(led_start); + return 0; +} + +__initcall(leds_init); diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c new file mode 100644 index 000000000000..e095b1fe8d8a --- /dev/null +++ b/arch/arm/mach-at91/pm.c @@ -0,0 +1,227 @@ +/* + * arch/arm/mach-at91/pm.c + * AT91 Power Management + * + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include "generic.h" + + +static int at91_pm_valid_state(suspend_state_t state) +{ + switch (state) { + case PM_SUSPEND_ON: + case PM_SUSPEND_STANDBY: + case PM_SUSPEND_MEM: + return 1; + + default: + return 0; + } +} + + +static suspend_state_t target_state; + +/* + * Called after processes are frozen, but before we shutdown devices. + */ +static int at91_pm_prepare(suspend_state_t state) +{ + target_state = state; + return 0; +} + +/* + * Verify that all the clocks are correct before entering + * slow-clock mode. + */ +static int at91_pm_verify_clocks(void) +{ + unsigned long scsr; + int i; + + scsr = at91_sys_read(AT91_PMC_SCSR); + + /* USB must not be using PLLB */ + if (cpu_is_at91rm9200()) { + if ((scsr & (AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP)) != 0) { + pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); + return 0; + } + } else if (cpu_is_at91sam9260()) { +#warning "Check SAM9260 USB clocks" + } else if (cpu_is_at91sam9261()) { +#warning "Check SAM9261 USB clocks" + } + +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS + /* PCK0..PCK3 must be disabled, or configured to use clk32k */ + for (i = 0; i < 4; i++) { + u32 css; + + if ((scsr & (AT91_PMC_PCK0 << i)) == 0) + continue; + + css = at91_sys_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS; + if (css != AT91_PMC_CSS_SLOW) { + pr_debug("AT91: PM - Suspend-to-RAM with PCK%d src %d\n", i, css); + return 0; + } + } +#endif + + return 1; +} + +/* + * Call this from platform driver suspend() to see how deeply to suspend. + * For example, some controllers (like OHCI) need one of the PLL clocks + * in order to act as a wakeup source, and those are not available when + * going into slow clock mode. + * + * REVISIT: generalize as clk_will_be_available(clk)? Other platforms have + * the very same problem (but not using at91 main_clk), and it'd be better + * to add one generic API rather than lots of platform-specific ones. + */ +int at91_suspend_entering_slow_clock(void) +{ + return (target_state == PM_SUSPEND_MEM); +} +EXPORT_SYMBOL(at91_suspend_entering_slow_clock); + + +static void (*slow_clock)(void); + + +static int at91_pm_enter(suspend_state_t state) +{ + at91_gpio_suspend(); + at91_irq_suspend(); + + pr_debug("AT91: PM - wake mask %08x, pm state %d\n", + /* remember all the always-wake irqs */ + (at91_sys_read(AT91_PMC_PCSR) + | (1 << AT91_ID_FIQ) + | (1 << AT91_ID_SYS) + | (at91_extern_irq)) + & at91_sys_read(AT91_AIC_IMR), + state); + + switch (state) { + /* + * Suspend-to-RAM is like STANDBY plus slow clock mode, so + * drivers must suspend more deeply: only the master clock + * controller may be using the main oscillator. + */ + case PM_SUSPEND_MEM: + /* + * Ensure that clocks are in a valid state. + */ + if (!at91_pm_verify_clocks()) + goto error; + + /* + * Enter slow clock mode by switching over to clk32k and + * turning off the main oscillator; reverse on wakeup. + */ + if (slow_clock) { + slow_clock(); + break; + } else { + /* DEVELOPMENT ONLY */ + pr_info("AT91: PM - no slow clock mode yet ...\n"); + /* FALLTHROUGH leaving master clock alone */ + } + + /* + * STANDBY mode has *all* drivers suspended; ignores irqs not + * marked as 'wakeup' event sources; and reduces DRAM power. + * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and + * nothing fancy done with main or cpu clocks. + */ + case PM_SUSPEND_STANDBY: + /* + * NOTE: the Wait-for-Interrupt instruction needs to be + * in icache so the SDRAM stays in self-refresh mode until + * the wakeup IRQ occurs. + */ + asm("b 1f; .align 5; 1:"); + asm("mcr p15, 0, r0, c7, c10, 4"); /* drain write buffer */ + at91_sys_write(AT91_SDRAMC_SRR, 1); /* self-refresh mode */ + /* fall though to next state */ + + case PM_SUSPEND_ON: + asm("mcr p15, 0, r0, c7, c0, 4"); /* wait for interrupt */ + break; + + default: + pr_debug("AT91: PM - bogus suspend state %d\n", state); + goto error; + } + + pr_debug("AT91: PM - wakeup %08x\n", + at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR)); + +error: + target_state = PM_SUSPEND_ON; + at91_irq_resume(); + at91_gpio_resume(); + return 0; +} + + +static struct pm_ops at91_pm_ops ={ + .pm_disk_mode = 0, + .valid = at91_pm_valid_state, + .prepare = at91_pm_prepare, + .enter = at91_pm_enter, +}; + +static int __init at91_pm_init(void) +{ + printk("AT91: Power Management\n"); + +#ifdef CONFIG_AT91_PM_SLOW_CLOCK + /* REVISIT allocations of SRAM should be dynamically managed. + * FIQ handlers and other components will want SRAM/TCM too... + */ + slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K)); + memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz); +#endif + + /* Disable SDRAM low-power mode. Cannot be used with self-refresh. */ + at91_sys_write(AT91_SDRAMC_LPR, 0); + + pm_set_ops(&at91_pm_ops); + + return 0; +} +arch_initcall(at91_pm_init); diff --git a/arch/arm/mach-at91rm9200/Kconfig b/arch/arm/mach-at91rm9200/Kconfig deleted file mode 100644 index 9f11db8af233..000000000000 --- a/arch/arm/mach-at91rm9200/Kconfig +++ /dev/null @@ -1,148 +0,0 @@ -if ARCH_AT91 - -menu "Atmel AT91 System-on-Chip" - -choice - prompt "Atmel AT91 Processor" - -config ARCH_AT91RM9200 - bool "AT91RM9200" - -config ARCH_AT91SAM9260 - bool "AT91SAM9260" - -config ARCH_AT91SAM9261 - bool "AT91SAM9261" - -endchoice - -# ---------------------------------------------------------- - -if ARCH_AT91RM9200 - -comment "AT91RM9200 Board Type" - -config MACH_ONEARM - bool "Ajeco 1ARM Single Board Computer" - depends on ARCH_AT91RM9200 - help - Select this if you are using Ajeco's 1ARM Single Board Computer. - - -config ARCH_AT91RM9200DK - bool "Atmel AT91RM9200-DK Development board" - depends on ARCH_AT91RM9200 - help - Select this if you are using Atmel's AT91RM9200-DK Development board. - (Discontinued) - -config MACH_AT91RM9200EK - bool "Atmel AT91RM9200-EK Evaluation Kit" - depends on ARCH_AT91RM9200 - help - Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit. - - -config MACH_CSB337 - bool "Cogent CSB337" - depends on ARCH_AT91RM9200 - help - Select this if you are using Cogent's CSB337 board. - - -config MACH_CSB637 - bool "Cogent CSB637" - depends on ARCH_AT91RM9200 - help - Select this if you are using Cogent's CSB637 board. - - -config MACH_CARMEVA - bool "Conitec ARM&EVA" - depends on ARCH_AT91RM9200 - help - Select this if you are using Conitec's AT91RM9200-MCU-Module. - - -config MACH_ATEB9200 - bool "Embest ATEB9200" - depends on ARCH_AT91RM9200 - help - Select this if you are using Embest's ATEB9200 board. - - -config MACH_KB9200 - bool "KwikByte KB920x" - depends on ARCH_AT91RM9200 - help - Select this if you are using KwikByte's KB920x board. - - -config MACH_KAFA - bool "Sperry-Sun KAFA board" - depends on ARCH_AT91RM9200 - help - Select this if you are using Sperry-Sun's KAFA board. - -endif - -# ---------------------------------------------------------- - -if ARCH_AT91SAM9260 - -comment "AT91SAM9260 Board Type" - -config MACH_AT91SAM9260EK - bool "Atmel AT91SAM9260-EK Evaluation Kit" - depends on ARCH_AT91SAM9260 - help - Select this if you are using Atmel's AT91SAM9260-EK Evaluation Kit. - - -endif - -# ---------------------------------------------------------- - -if ARCH_AT91SAM9261 - -comment "AT91SAM9261 Board Type" - -config MACH_AT91SAM9261EK - bool "Atmel AT91SAM9261-EK Evaluation Kit" - depends on ARCH_AT91SAM9261 - help - Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit. - - -endif - -# ---------------------------------------------------------- - -comment "AT91 Board Options" - -config MTD_AT91_DATAFLASH_CARD - bool "Enable DataFlash Card support" - depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK) - help - Enable support for the DataFlash card. - -config MTD_NAND_AT91_BUSWIDTH_16 - bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK) - help - On AT91SAM926x boards both types of NAND flash can be present - (8 and 16 bit data bus width). - -# ---------------------------------------------------------- - -comment "AT91 Feature Selections" - -config AT91_PROGRAMMABLE_CLOCKS - bool "Programmable Clocks" - help - Select this if you need to program one or more of the PCK0..PCK3 - programmable clock outputs. - -endmenu - -endif diff --git a/arch/arm/mach-at91rm9200/Makefile b/arch/arm/mach-at91rm9200/Makefile deleted file mode 100644 index cf777007847a..000000000000 --- a/arch/arm/mach-at91rm9200/Makefile +++ /dev/null @@ -1,49 +0,0 @@ -# -# Makefile for the linux kernel. -# - -obj-y := clock.o irq.o gpio.o -obj-m := -obj-n := -obj- := - -obj-$(CONFIG_PM) += pm.o - -# CPU-specific support -obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devices.o -obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o -obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o - -# AT91RM9200 board-specific support -obj-$(CONFIG_MACH_ONEARM) += board-1arm.o -obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o -obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o -obj-$(CONFIG_MACH_CSB337) += board-csb337.o -obj-$(CONFIG_MACH_CSB637) += board-csb637.o -obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o -obj-$(CONFIG_MACH_KB9200) += board-kb9202.o -obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o -obj-$(CONFIG_MACH_KAFA) += board-kafa.o - -# AT91SAM9260 board-specific support -obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o - -# AT91SAM9261 board-specific support -obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o - -# LEDs support -led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o -led-$(CONFIG_MACH_AT91RM9200EK) += leds.o -led-$(CONFIG_MACH_CSB337) += leds.o -led-$(CONFIG_MACH_CSB637) += leds.o -led-$(CONFIG_MACH_KB9200) += leds.o -led-$(CONFIG_MACH_KAFA) += leds.o -obj-$(CONFIG_LEDS) += $(led-y) - -# VGA support -#obj-$(CONFIG_FB_S1D13XXX) += ics1523.o - - -ifeq ($(CONFIG_PM_DEBUG),y) -CFLAGS_pm.o += -DDEBUG -endif diff --git a/arch/arm/mach-at91rm9200/Makefile.boot b/arch/arm/mach-at91rm9200/Makefile.boot deleted file mode 100644 index e667dcc7cd34..000000000000 --- a/arch/arm/mach-at91rm9200/Makefile.boot +++ /dev/null @@ -1,9 +0,0 @@ -# Note: the following conditions must always be true: -# ZRELADDR == virt_to_phys(TEXTADDR) -# PARAMS_PHYS must be within 4MB of ZRELADDR -# INITRD_PHYS must be in RAM - - zreladdr-y := 0x20008000 -params_phys-y := 0x20000100 -initrd_phys-y := 0x20410000 - diff --git a/arch/arm/mach-at91rm9200/at91rm9200.c b/arch/arm/mach-at91rm9200/at91rm9200.c deleted file mode 100644 index a92e9a495b07..000000000000 --- a/arch/arm/mach-at91rm9200/at91rm9200.c +++ /dev/null @@ -1,294 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/at91rm9200.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#include - -#include -#include -#include -#include -#include - -#include "generic.h" -#include "clock.h" - -static struct map_desc at91rm9200_io_desc[] __initdata = { - { - .virtual = AT91_VA_BASE_SYS, - .pfn = __phys_to_pfn(AT91_BASE_SYS), - .length = SZ_4K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_EMAC, - .pfn = __phys_to_pfn(AT91RM9200_BASE_EMAC), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_IO_VIRT_BASE - AT91RM9200_SRAM_SIZE, - .pfn = __phys_to_pfn(AT91RM9200_SRAM_BASE), - .length = AT91RM9200_SRAM_SIZE, - .type = MT_DEVICE, - }, -}; - -/* -------------------------------------------------------------------- - * Clocks - * -------------------------------------------------------------------- */ - -/* - * The peripheral clocks. - */ -static struct clk udc_clk = { - .name = "udc_clk", - .pmc_mask = 1 << AT91RM9200_ID_UDP, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk ohci_clk = { - .name = "ohci_clk", - .pmc_mask = 1 << AT91RM9200_ID_UHP, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk ether_clk = { - .name = "ether_clk", - .pmc_mask = 1 << AT91RM9200_ID_EMAC, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk mmc_clk = { - .name = "mci_clk", - .pmc_mask = 1 << AT91RM9200_ID_MCI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk twi_clk = { - .name = "twi_clk", - .pmc_mask = 1 << AT91RM9200_ID_TWI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart0_clk = { - .name = "usart0_clk", - .pmc_mask = 1 << AT91RM9200_ID_US0, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart1_clk = { - .name = "usart1_clk", - .pmc_mask = 1 << AT91RM9200_ID_US1, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart2_clk = { - .name = "usart2_clk", - .pmc_mask = 1 << AT91RM9200_ID_US2, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart3_clk = { - .name = "usart3_clk", - .pmc_mask = 1 << AT91RM9200_ID_US3, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk spi_clk = { - .name = "spi_clk", - .pmc_mask = 1 << AT91RM9200_ID_SPI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioA_clk = { - .name = "pioA_clk", - .pmc_mask = 1 << AT91RM9200_ID_PIOA, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioB_clk = { - .name = "pioB_clk", - .pmc_mask = 1 << AT91RM9200_ID_PIOB, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioC_clk = { - .name = "pioC_clk", - .pmc_mask = 1 << AT91RM9200_ID_PIOC, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioD_clk = { - .name = "pioD_clk", - .pmc_mask = 1 << AT91RM9200_ID_PIOD, - .type = CLK_TYPE_PERIPHERAL, -}; - -static struct clk *periph_clocks[] __initdata = { - &pioA_clk, - &pioB_clk, - &pioC_clk, - &pioD_clk, - &usart0_clk, - &usart1_clk, - &usart2_clk, - &usart3_clk, - &mmc_clk, - &udc_clk, - &twi_clk, - &spi_clk, - // ssc 0 .. ssc2 - // tc0 .. tc5 - &ohci_clk, - ðer_clk, - // irq0 .. irq6 -}; - -/* - * The four programmable clocks. - * You must configure pin multiplexing to bring these signals out. - */ -static struct clk pck0 = { - .name = "pck0", - .pmc_mask = AT91_PMC_PCK0, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 0, -}; -static struct clk pck1 = { - .name = "pck1", - .pmc_mask = AT91_PMC_PCK1, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 1, -}; -static struct clk pck2 = { - .name = "pck2", - .pmc_mask = AT91_PMC_PCK2, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 2, -}; -static struct clk pck3 = { - .name = "pck3", - .pmc_mask = AT91_PMC_PCK3, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 3, -}; - -static void __init at91rm9200_register_clocks(void) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) - clk_register(periph_clocks[i]); - - clk_register(&pck0); - clk_register(&pck1); - clk_register(&pck2); - clk_register(&pck3); -} - -/* -------------------------------------------------------------------- - * GPIO - * -------------------------------------------------------------------- */ - -static struct at91_gpio_bank at91rm9200_gpio[] = { - { - .id = AT91RM9200_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, - }, { - .id = AT91RM9200_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, - }, { - .id = AT91RM9200_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, - }, { - .id = AT91RM9200_ID_PIOD, - .offset = AT91_PIOD, - .clock = &pioD_clk, - } -}; - -static void at91rm9200_reset(void) -{ - /* - * Perform a hardware reset with the use of the Watchdog timer. - */ - at91_sys_write(AT91_ST_WDMR, AT91_ST_RSTEN | AT91_ST_EXTEN | 1); - at91_sys_write(AT91_ST_CR, AT91_ST_WDRST); -} - - -/* -------------------------------------------------------------------- - * AT91RM9200 processor initialization - * -------------------------------------------------------------------- */ -void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks) -{ - /* Map peripherals */ - iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); - - at91_arch_reset = at91rm9200_reset; - at91_extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1) - | (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3) - | (1 << AT91RM9200_ID_IRQ4) | (1 << AT91RM9200_ID_IRQ5) - | (1 << AT91RM9200_ID_IRQ6); - - /* Init clock subsystem */ - at91_clock_init(main_clock); - - /* Register the processor-specific clocks */ - at91rm9200_register_clocks(); - - /* Initialize GPIO subsystem */ - at91_gpio_init(at91rm9200_gpio, banks); -} - - -/* -------------------------------------------------------------------- - * Interrupt initialization - * -------------------------------------------------------------------- */ - -/* - * The default interrupt priority levels (0 = lowest, 7 = highest). - */ -static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = { - 7, /* Advanced Interrupt Controller (FIQ) */ - 7, /* System Peripherals */ - 0, /* Parallel IO Controller A */ - 0, /* Parallel IO Controller B */ - 0, /* Parallel IO Controller C */ - 0, /* Parallel IO Controller D */ - 6, /* USART 0 */ - 6, /* USART 1 */ - 6, /* USART 2 */ - 6, /* USART 3 */ - 0, /* Multimedia Card Interface */ - 4, /* USB Device Port */ - 0, /* Two-Wire Interface */ - 6, /* Serial Peripheral Interface */ - 5, /* Serial Synchronous Controller 0 */ - 5, /* Serial Synchronous Controller 1 */ - 5, /* Serial Synchronous Controller 2 */ - 0, /* Timer Counter 0 */ - 0, /* Timer Counter 1 */ - 0, /* Timer Counter 2 */ - 0, /* Timer Counter 3 */ - 0, /* Timer Counter 4 */ - 0, /* Timer Counter 5 */ - 3, /* USB Host port */ - 3, /* Ethernet MAC */ - 0, /* Advanced Interrupt Controller (IRQ0) */ - 0, /* Advanced Interrupt Controller (IRQ1) */ - 0, /* Advanced Interrupt Controller (IRQ2) */ - 0, /* Advanced Interrupt Controller (IRQ3) */ - 0, /* Advanced Interrupt Controller (IRQ4) */ - 0, /* Advanced Interrupt Controller (IRQ5) */ - 0 /* Advanced Interrupt Controller (IRQ6) */ -}; - -void __init at91rm9200_init_interrupts(unsigned int priority[NR_AIC_IRQS]) -{ - if (!priority) - priority = at91rm9200_default_irq_priority; - - /* Initialize the AIC interrupt controller */ - at91_aic_init(priority); - - /* Enable GPIO interrupts */ - at91_gpio_irq_setup(); -} diff --git a/arch/arm/mach-at91rm9200/at91rm9200_devices.c b/arch/arm/mach-at91rm9200/at91rm9200_devices.c deleted file mode 100644 index 57fac7203fe4..000000000000 --- a/arch/arm/mach-at91rm9200/at91rm9200_devices.c +++ /dev/null @@ -1,875 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/at91rm9200_devices.c - * - * Copyright (C) 2005 Thibaut VARENE - * Copyright (C) 2005 David Brownell - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ -#include -#include - -#include - -#include -#include -#include -#include - -#include "generic.h" - -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 - -/* -------------------------------------------------------------------- - * USB Host - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) -static u64 ohci_dmamask = 0xffffffffUL; -static struct at91_usbh_data usbh_data; - -static struct resource usbh_resources[] = { - [0] = { - .start = AT91RM9200_UHP_BASE, - .end = AT91RM9200_UHP_BASE + SZ_1M - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_UHP, - .end = AT91RM9200_ID_UHP, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91rm9200_usbh_device = { - .name = "at91_ohci", - .id = -1, - .dev = { - .dma_mask = &ohci_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &usbh_data, - }, - .resource = usbh_resources, - .num_resources = ARRAY_SIZE(usbh_resources), -}; - -void __init at91_add_device_usbh(struct at91_usbh_data *data) -{ - if (!data) - return; - - usbh_data = *data; - platform_device_register(&at91rm9200_usbh_device); -} -#else -void __init at91_add_device_usbh(struct at91_usbh_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * USB Device (Gadget) - * -------------------------------------------------------------------- */ - -#ifdef CONFIG_USB_GADGET_AT91 -static struct at91_udc_data udc_data; - -static struct resource udc_resources[] = { - [0] = { - .start = AT91RM9200_BASE_UDP, - .end = AT91RM9200_BASE_UDP + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_UDP, - .end = AT91RM9200_ID_UDP, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91rm9200_udc_device = { - .name = "at91_udc", - .id = -1, - .dev = { - .platform_data = &udc_data, - }, - .resource = udc_resources, - .num_resources = ARRAY_SIZE(udc_resources), -}; - -void __init at91_add_device_udc(struct at91_udc_data *data) -{ - if (!data) - return; - - if (data->vbus_pin) { - at91_set_gpio_input(data->vbus_pin, 0); - at91_set_deglitch(data->vbus_pin, 1); - } - if (data->pullup_pin) - at91_set_gpio_output(data->pullup_pin, 0); - - udc_data = *data; - platform_device_register(&at91rm9200_udc_device); -} -#else -void __init at91_add_device_udc(struct at91_udc_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * Ethernet - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE) -static u64 eth_dmamask = 0xffffffffUL; -static struct at91_eth_data eth_data; - -static struct resource eth_resources[] = { - [0] = { - .start = AT91_VA_BASE_EMAC, - .end = AT91_VA_BASE_EMAC + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_EMAC, - .end = AT91RM9200_ID_EMAC, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91rm9200_eth_device = { - .name = "at91_ether", - .id = -1, - .dev = { - .dma_mask = ð_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = ð_data, - }, - .resource = eth_resources, - .num_resources = ARRAY_SIZE(eth_resources), -}; - -void __init at91_add_device_eth(struct at91_eth_data *data) -{ - if (!data) - return; - - if (data->phy_irq_pin) { - at91_set_gpio_input(data->phy_irq_pin, 0); - at91_set_deglitch(data->phy_irq_pin, 1); - } - - /* Pins used for MII and RMII */ - at91_set_A_periph(AT91_PIN_PA16, 0); /* EMDIO */ - at91_set_A_periph(AT91_PIN_PA15, 0); /* EMDC */ - at91_set_A_periph(AT91_PIN_PA14, 0); /* ERXER */ - at91_set_A_periph(AT91_PIN_PA13, 0); /* ERX1 */ - at91_set_A_periph(AT91_PIN_PA12, 0); /* ERX0 */ - at91_set_A_periph(AT91_PIN_PA11, 0); /* ECRS_ECRSDV */ - at91_set_A_periph(AT91_PIN_PA10, 0); /* ETX1 */ - at91_set_A_periph(AT91_PIN_PA9, 0); /* ETX0 */ - at91_set_A_periph(AT91_PIN_PA8, 0); /* ETXEN */ - at91_set_A_periph(AT91_PIN_PA7, 0); /* ETXCK_EREFCK */ - - if (!data->is_rmii) { - at91_set_B_periph(AT91_PIN_PB19, 0); /* ERXCK */ - at91_set_B_periph(AT91_PIN_PB18, 0); /* ECOL */ - at91_set_B_periph(AT91_PIN_PB17, 0); /* ERXDV */ - at91_set_B_periph(AT91_PIN_PB16, 0); /* ERX3 */ - at91_set_B_periph(AT91_PIN_PB15, 0); /* ERX2 */ - at91_set_B_periph(AT91_PIN_PB14, 0); /* ETXER */ - at91_set_B_periph(AT91_PIN_PB13, 0); /* ETX3 */ - at91_set_B_periph(AT91_PIN_PB12, 0); /* ETX2 */ - } - - eth_data = *data; - platform_device_register(&at91rm9200_eth_device); -} -#else -void __init at91_add_device_eth(struct at91_eth_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * Compact Flash / PCMCIA - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) -static struct at91_cf_data cf_data; - -#define CF_BASE AT91_CHIPSELECT_4 - -static struct resource cf_resources[] = { - [0] = { - .start = CF_BASE, - /* ties up CS4, CS5 and CS6 */ - .end = CF_BASE + (0x30000000 - 1), - .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT, - }, -}; - -static struct platform_device at91rm9200_cf_device = { - .name = "at91_cf", - .id = -1, - .dev = { - .platform_data = &cf_data, - }, - .resource = cf_resources, - .num_resources = ARRAY_SIZE(cf_resources), -}; - -void __init at91_add_device_cf(struct at91_cf_data *data) -{ - unsigned int csa; - - if (!data) - return; - - data->chipselect = 4; /* can only use EBI ChipSelect 4 */ - - /* CF takes over CS4, CS5, CS6 */ - csa = at91_sys_read(AT91_EBI_CSA); - at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH); - - /* - * Static memory controller timing adjustments. - * REVISIT: these timings are in terms of MCK cycles, so - * when MCK changes (cpufreq etc) so must these values... - */ - at91_sys_write(AT91_SMC_CSR(4), - AT91_SMC_ACSS_STD - | AT91_SMC_DBW_16 - | AT91_SMC_BAT - | AT91_SMC_WSEN - | AT91_SMC_NWS_(32) /* wait states */ - | AT91_SMC_RWSETUP_(6) /* setup time */ - | AT91_SMC_RWHOLD_(4) /* hold time */ - ); - - /* input/irq */ - if (data->irq_pin) { - at91_set_gpio_input(data->irq_pin, 1); - at91_set_deglitch(data->irq_pin, 1); - } - at91_set_gpio_input(data->det_pin, 1); - at91_set_deglitch(data->det_pin, 1); - - /* outputs, initially off */ - if (data->vcc_pin) - at91_set_gpio_output(data->vcc_pin, 0); - at91_set_gpio_output(data->rst_pin, 0); - - /* force poweron defaults for these pins ... */ - at91_set_A_periph(AT91_PIN_PC9, 0); /* A25/CFRNW */ - at91_set_A_periph(AT91_PIN_PC10, 0); /* NCS4/CFCS */ - at91_set_A_periph(AT91_PIN_PC11, 0); /* NCS5/CFCE1 */ - at91_set_A_periph(AT91_PIN_PC12, 0); /* NCS6/CFCE2 */ - - /* nWAIT is _not_ a default setting */ - at91_set_A_periph(AT91_PIN_PC6, 1); /* nWAIT */ - - cf_data = *data; - platform_device_register(&at91rm9200_cf_device); -} -#else -void __init at91_add_device_cf(struct at91_cf_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * MMC / SD - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) -static u64 mmc_dmamask = 0xffffffffUL; -static struct at91_mmc_data mmc_data; - -static struct resource mmc_resources[] = { - [0] = { - .start = AT91RM9200_BASE_MCI, - .end = AT91RM9200_BASE_MCI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_MCI, - .end = AT91RM9200_ID_MCI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91rm9200_mmc_device = { - .name = "at91_mci", - .id = -1, - .dev = { - .dma_mask = &mmc_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &mmc_data, - }, - .resource = mmc_resources, - .num_resources = ARRAY_SIZE(mmc_resources), -}; - -void __init at91_add_device_mmc(struct at91_mmc_data *data) -{ - if (!data) - return; - - /* input/irq */ - if (data->det_pin) { - at91_set_gpio_input(data->det_pin, 1); - at91_set_deglitch(data->det_pin, 1); - } - if (data->wp_pin) - at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) - at91_set_gpio_output(data->vcc_pin, 0); - - /* CLK */ - at91_set_A_periph(AT91_PIN_PA27, 0); - - if (data->slot_b) { - /* CMD */ - at91_set_B_periph(AT91_PIN_PA8, 1); - - /* DAT0, maybe DAT1..DAT3 */ - at91_set_B_periph(AT91_PIN_PA9, 1); - if (data->wire4) { - at91_set_B_periph(AT91_PIN_PA10, 1); - at91_set_B_periph(AT91_PIN_PA11, 1); - at91_set_B_periph(AT91_PIN_PA12, 1); - } - } else { - /* CMD */ - at91_set_A_periph(AT91_PIN_PA28, 1); - - /* DAT0, maybe DAT1..DAT3 */ - at91_set_A_periph(AT91_PIN_PA29, 1); - if (data->wire4) { - at91_set_B_periph(AT91_PIN_PB3, 1); - at91_set_B_periph(AT91_PIN_PB4, 1); - at91_set_B_periph(AT91_PIN_PB5, 1); - } - } - - mmc_data = *data; - platform_device_register(&at91rm9200_mmc_device); -} -#else -void __init at91_add_device_mmc(struct at91_mmc_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * NAND / SmartMedia - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) -static struct at91_nand_data nand_data; - -#define NAND_BASE AT91_CHIPSELECT_3 - -static struct resource nand_resources[] = { - { - .start = NAND_BASE, - .end = NAND_BASE + SZ_8M - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device at91rm9200_nand_device = { - .name = "at91_nand", - .id = -1, - .dev = { - .platform_data = &nand_data, - }, - .resource = nand_resources, - .num_resources = ARRAY_SIZE(nand_resources), -}; - -void __init at91_add_device_nand(struct at91_nand_data *data) -{ - unsigned int csa; - - if (!data) - return; - - /* enable the address range of CS3 */ - csa = at91_sys_read(AT91_EBI_CSA); - at91_sys_write(AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA); - - /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN - | AT91_SMC_NWS_(5) - | AT91_SMC_TDF_(1) - | AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */ - | AT91_SMC_RWHOLD_(1) /* tDH Data Hold Time 20 - ns */ - ); - - /* enable pin */ - if (data->enable_pin) - at91_set_gpio_output(data->enable_pin, 1); - - /* ready/busy pin */ - if (data->rdy_pin) - at91_set_gpio_input(data->rdy_pin, 1); - - /* card detect pin */ - if (data->det_pin) - at91_set_gpio_input(data->det_pin, 1); - - at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */ - at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */ - - nand_data = *data; - platform_device_register(&at91rm9200_nand_device); -} -#else -void __init at91_add_device_nand(struct at91_nand_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * TWI (i2c) - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) - -static struct resource twi_resources[] = { - [0] = { - .start = AT91RM9200_BASE_TWI, - .end = AT91RM9200_BASE_TWI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_TWI, - .end = AT91RM9200_ID_TWI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91rm9200_twi_device = { - .name = "at91_i2c", - .id = -1, - .resource = twi_resources, - .num_resources = ARRAY_SIZE(twi_resources), -}; - -void __init at91_add_device_i2c(void) -{ - /* pins used for TWI interface */ - at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */ - at91_set_multi_drive(AT91_PIN_PA25, 1); - - at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */ - at91_set_multi_drive(AT91_PIN_PA26, 1); - - platform_device_register(&at91rm9200_twi_device); -} -#else -void __init at91_add_device_i2c(void) {} -#endif - - -/* -------------------------------------------------------------------- - * SPI - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) -static u64 spi_dmamask = 0xffffffffUL; - -static struct resource spi_resources[] = { - [0] = { - .start = AT91RM9200_BASE_SPI, - .end = AT91RM9200_BASE_SPI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_SPI, - .end = AT91RM9200_ID_SPI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91rm9200_spi_device = { - .name = "at91_spi", - .id = 0, - .dev = { - .dma_mask = &spi_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .resource = spi_resources, - .num_resources = ARRAY_SIZE(spi_resources), -}; - -static const unsigned spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 }; - -void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) -{ - int i; - unsigned long cs_pin; - - at91_set_A_periph(AT91_PIN_PA0, 0); /* MISO */ - at91_set_A_periph(AT91_PIN_PA1, 0); /* MOSI */ - at91_set_A_periph(AT91_PIN_PA2, 0); /* SPCK */ - - /* Enable SPI chip-selects */ - for (i = 0; i < nr_devices; i++) { - if (devices[i].controller_data) - cs_pin = (unsigned long) devices[i].controller_data; - else - cs_pin = spi_standard_cs[devices[i].chip_select]; - -#ifdef CONFIG_SPI_AT91_MANUAL_CS - at91_set_gpio_output(cs_pin, 1); -#else - at91_set_A_periph(cs_pin, 0); -#endif - - /* pass chip-select pin to driver */ - devices[i].controller_data = (void *) cs_pin; - } - - spi_register_board_info(devices, nr_devices); - at91_clock_associate("spi_clk", &at91rm9200_spi_device.dev, "spi"); - platform_device_register(&at91rm9200_spi_device); -} -#else -void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} -#endif - - -/* -------------------------------------------------------------------- - * RTC - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE) -static struct platform_device at91rm9200_rtc_device = { - .name = "at91_rtc", - .id = -1, - .num_resources = 0, -}; - -static void __init at91_add_device_rtc(void) -{ - platform_device_register(&at91rm9200_rtc_device); -} -#else -static void __init at91_add_device_rtc(void) {} -#endif - - -/* -------------------------------------------------------------------- - * Watchdog - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_AT91RM9200_WATCHDOG) || defined(CONFIG_AT91RM9200_WATCHDOG_MODULE) -static struct platform_device at91rm9200_wdt_device = { - .name = "at91_wdt", - .id = -1, - .num_resources = 0, -}; - -static void __init at91_add_device_watchdog(void) -{ - platform_device_register(&at91rm9200_wdt_device); -} -#else -static void __init at91_add_device_watchdog(void) {} -#endif - - -/* -------------------------------------------------------------------- - * LEDs - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_LEDS) -u8 at91_leds_cpu; -u8 at91_leds_timer; - -void __init at91_init_leds(u8 cpu_led, u8 timer_led) -{ - at91_leds_cpu = cpu_led; - at91_leds_timer = timer_led; -} -#else -void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} -#endif - - -/* -------------------------------------------------------------------- - * UART - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_SERIAL_ATMEL) -static struct resource dbgu_resources[] = { - [0] = { - .start = AT91_VA_BASE_SYS + AT91_DBGU, - .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91_ID_SYS, - .end = AT91_ID_SYS, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data dbgu_data = { - .use_dma_tx = 0, - .use_dma_rx = 0, /* DBGU not capable of receive DMA */ - .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), -}; - -static struct platform_device at91rm9200_dbgu_device = { - .name = "atmel_usart", - .id = 0, - .dev = { - .platform_data = &dbgu_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = dbgu_resources, - .num_resources = ARRAY_SIZE(dbgu_resources), -}; - -static inline void configure_dbgu_pins(void) -{ - at91_set_A_periph(AT91_PIN_PA30, 0); /* DRXD */ - at91_set_A_periph(AT91_PIN_PA31, 1); /* DTXD */ -} - -static struct resource uart0_resources[] = { - [0] = { - .start = AT91RM9200_BASE_US0, - .end = AT91RM9200_BASE_US0 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_US0, - .end = AT91RM9200_ID_US0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart0_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91rm9200_uart0_device = { - .name = "atmel_usart", - .id = 1, - .dev = { - .platform_data = &uart0_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart0_resources, - .num_resources = ARRAY_SIZE(uart0_resources), -}; - -static inline void configure_usart0_pins(void) -{ - at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */ - at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */ - at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */ - - /* - * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21. - * We need to drive the pin manually. Default is off (RTS is active low). - */ - at91_set_gpio_output(AT91_PIN_PA21, 1); -} - -static struct resource uart1_resources[] = { - [0] = { - .start = AT91RM9200_BASE_US1, - .end = AT91RM9200_BASE_US1 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_US1, - .end = AT91RM9200_ID_US1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart1_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91rm9200_uart1_device = { - .name = "atmel_usart", - .id = 2, - .dev = { - .platform_data = &uart1_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart1_resources, - .num_resources = ARRAY_SIZE(uart1_resources), -}; - -static inline void configure_usart1_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */ - at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */ - at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */ - at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */ - at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */ - at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */ - at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */ - at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */ -} - -static struct resource uart2_resources[] = { - [0] = { - .start = AT91RM9200_BASE_US2, - .end = AT91RM9200_BASE_US2 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_US2, - .end = AT91RM9200_ID_US2, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart2_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91rm9200_uart2_device = { - .name = "atmel_usart", - .id = 3, - .dev = { - .platform_data = &uart2_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart2_resources, - .num_resources = ARRAY_SIZE(uart2_resources), -}; - -static inline void configure_usart2_pins(void) -{ - at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */ - at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */ -} - -static struct resource uart3_resources[] = { - [0] = { - .start = AT91RM9200_BASE_US3, - .end = AT91RM9200_BASE_US3 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91RM9200_ID_US3, - .end = AT91RM9200_ID_US3, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart3_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91rm9200_uart3_device = { - .name = "atmel_usart", - .id = 4, - .dev = { - .platform_data = &uart3_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart3_resources, - .num_resources = ARRAY_SIZE(uart3_resources), -}; - -static inline void configure_usart3_pins(void) -{ - at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */ - at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */ -} - -struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -struct platform_device *atmel_default_console_device; /* the serial console device */ - -void __init at91_init_serial(struct at91_uart_config *config) -{ - int i; - - /* Fill in list of supported UARTs */ - for (i = 0; i < config->nr_tty; i++) { - switch (config->tty_map[i]) { - case 0: - configure_usart0_pins(); - at91_uarts[i] = &at91rm9200_uart0_device; - at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart"); - break; - case 1: - configure_usart1_pins(); - at91_uarts[i] = &at91rm9200_uart1_device; - at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart"); - break; - case 2: - configure_usart2_pins(); - at91_uarts[i] = &at91rm9200_uart2_device; - at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart"); - break; - case 3: - configure_usart3_pins(); - at91_uarts[i] = &at91rm9200_uart3_device; - at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart"); - break; - case 4: - configure_dbgu_pins(); - at91_uarts[i] = &at91rm9200_dbgu_device; - at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart"); - break; - default: - continue; - } - at91_uarts[i]->id = i; /* update ID number to mapped ID */ - } - - /* Set serial console device */ - if (config->console_tty < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[config->console_tty]; - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); -} - -void __init at91_add_device_serial(void) -{ - int i; - - for (i = 0; i < ATMEL_MAX_UART; i++) { - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -} -#else -void __init at91_init_serial(struct at91_uart_config *config) {} -void __init at91_add_device_serial(void) {} -#endif - - -/* -------------------------------------------------------------------- */ - -/* - * These devices are always present and don't need any board-specific - * setup. - */ -static int __init at91_add_standard_devices(void) -{ - at91_add_device_rtc(); - at91_add_device_watchdog(); - return 0; -} - -arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91rm9200/at91rm9200_time.c b/arch/arm/mach-at91rm9200/at91rm9200_time.c deleted file mode 100644 index b999e192a7e9..000000000000 --- a/arch/arm/mach-at91rm9200/at91rm9200_time.c +++ /dev/null @@ -1,146 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/at91rm9200_time.c - * - * Copyright (C) 2003 SAN People - * Copyright (C) 2003 ATMEL - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - -static unsigned long last_crtr; - -/* - * The ST_CRTR is updated asynchronously to the master clock. It is therefore - * necessary to read it twice (with the same value) to ensure accuracy. - */ -static inline unsigned long read_CRTR(void) { - unsigned long x1, x2; - - do { - x1 = at91_sys_read(AT91_ST_CRTR); - x2 = at91_sys_read(AT91_ST_CRTR); - } while (x1 != x2); - - return x1; -} - -/* - * Returns number of microseconds since last timer interrupt. Note that interrupts - * will have been disabled by do_gettimeofday() - * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. - * 'tick' is usecs per jiffy (linux/timex.h). - */ -static unsigned long at91rm9200_gettimeoffset(void) -{ - unsigned long elapsed; - - elapsed = (read_CRTR() - last_crtr) & AT91_ST_ALMV; - - return (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH; -} - -/* - * IRQ handler for the timer. - */ -static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id) -{ - if (at91_sys_read(AT91_ST_SR) & AT91_ST_PITS) { /* This is a shared interrupt */ - write_seqlock(&xtime_lock); - - while (((read_CRTR() - last_crtr) & AT91_ST_ALMV) >= LATCH) { - timer_tick(); - last_crtr = (last_crtr + LATCH) & AT91_ST_ALMV; - } - - write_sequnlock(&xtime_lock); - - return IRQ_HANDLED; - } - else - return IRQ_NONE; /* not handled */ -} - -static struct irqaction at91rm9200_timer_irq = { - .name = "at91_tick", - .flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER, - .handler = at91rm9200_timer_interrupt -}; - -void at91rm9200_timer_reset(void) -{ - last_crtr = 0; - - /* Real time counter incremented every 30.51758 microseconds */ - at91_sys_write(AT91_ST_RTMR, 1); - - /* Set Period Interval timer */ - at91_sys_write(AT91_ST_PIMR, LATCH); - - /* Clear any pending interrupts */ - (void) at91_sys_read(AT91_ST_SR); - - /* Enable Period Interval Timer interrupt */ - at91_sys_write(AT91_ST_IER, AT91_ST_PITS); -} - -/* - * Set up timer interrupt. - */ -void __init at91rm9200_timer_init(void) -{ - /* Disable all timer interrupts */ - at91_sys_write(AT91_ST_IDR, AT91_ST_PITS | AT91_ST_WDOVF | AT91_ST_RTTINC | AT91_ST_ALMS); - (void) at91_sys_read(AT91_ST_SR); /* Clear any pending interrupts */ - - /* Make IRQs happen for the system timer */ - setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq); - - /* Change the kernel's 'tick' value to 10009 usec. (the default is 10000) */ - tick_usec = (LATCH * 1000000) / CLOCK_TICK_RATE; - - /* Initialize and enable the timer interrupt */ - at91rm9200_timer_reset(); -} - -#ifdef CONFIG_PM -static void at91rm9200_timer_suspend(void) -{ - /* disable Period Interval Timer interrupt */ - at91_sys_write(AT91_ST_IDR, AT91_ST_PITS); -} -#else -#define at91rm9200_timer_suspend NULL -#endif - -struct sys_timer at91rm9200_timer = { - .init = at91rm9200_timer_init, - .offset = at91rm9200_gettimeoffset, - .suspend = at91rm9200_timer_suspend, - .resume = at91rm9200_timer_reset, -}; - diff --git a/arch/arm/mach-at91rm9200/at91sam9260.c b/arch/arm/mach-at91rm9200/at91sam9260.c deleted file mode 100644 index b14871adc300..000000000000 --- a/arch/arm/mach-at91rm9200/at91sam9260.c +++ /dev/null @@ -1,295 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/at91sam9260.c - * - * Copyright (C) 2006 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#include - -#include -#include -#include -#include -#include - -#include "generic.h" -#include "clock.h" - -static struct map_desc at91sam9260_io_desc[] __initdata = { - { - .virtual = AT91_VA_BASE_SYS, - .pfn = __phys_to_pfn(AT91_BASE_SYS), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE, - .pfn = __phys_to_pfn(AT91SAM9260_SRAM0_BASE), - .length = AT91SAM9260_SRAM0_SIZE, - .type = MT_DEVICE, - }, { - .virtual = AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE - AT91SAM9260_SRAM1_SIZE, - .pfn = __phys_to_pfn(AT91SAM9260_SRAM1_BASE), - .length = AT91SAM9260_SRAM1_SIZE, - .type = MT_DEVICE, - }, -}; - -/* -------------------------------------------------------------------- - * Clocks - * -------------------------------------------------------------------- */ - -/* - * The peripheral clocks. - */ -static struct clk pioA_clk = { - .name = "pioA_clk", - .pmc_mask = 1 << AT91SAM9260_ID_PIOA, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioB_clk = { - .name = "pioB_clk", - .pmc_mask = 1 << AT91SAM9260_ID_PIOB, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioC_clk = { - .name = "pioC_clk", - .pmc_mask = 1 << AT91SAM9260_ID_PIOC, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk adc_clk = { - .name = "adc_clk", - .pmc_mask = 1 << AT91SAM9260_ID_ADC, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart0_clk = { - .name = "usart0_clk", - .pmc_mask = 1 << AT91SAM9260_ID_US0, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart1_clk = { - .name = "usart1_clk", - .pmc_mask = 1 << AT91SAM9260_ID_US1, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart2_clk = { - .name = "usart2_clk", - .pmc_mask = 1 << AT91SAM9260_ID_US2, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk mmc_clk = { - .name = "mci_clk", - .pmc_mask = 1 << AT91SAM9260_ID_MCI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk udc_clk = { - .name = "udc_clk", - .pmc_mask = 1 << AT91SAM9260_ID_UDP, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk twi_clk = { - .name = "twi_clk", - .pmc_mask = 1 << AT91SAM9260_ID_TWI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk spi0_clk = { - .name = "spi0_clk", - .pmc_mask = 1 << AT91SAM9260_ID_SPI0, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk spi1_clk = { - .name = "spi1_clk", - .pmc_mask = 1 << AT91SAM9260_ID_SPI1, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk ohci_clk = { - .name = "ohci_clk", - .pmc_mask = 1 << AT91SAM9260_ID_UHP, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk ether_clk = { - .name = "ether_clk", - .pmc_mask = 1 << AT91SAM9260_ID_EMAC, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk isi_clk = { - .name = "isi_clk", - .pmc_mask = 1 << AT91SAM9260_ID_ISI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart3_clk = { - .name = "usart3_clk", - .pmc_mask = 1 << AT91SAM9260_ID_US3, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart4_clk = { - .name = "usart4_clk", - .pmc_mask = 1 << AT91SAM9260_ID_US4, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart5_clk = { - .name = "usart5_clk", - .pmc_mask = 1 << AT91SAM9260_ID_US5, - .type = CLK_TYPE_PERIPHERAL, -}; - -static struct clk *periph_clocks[] __initdata = { - &pioA_clk, - &pioB_clk, - &pioC_clk, - &adc_clk, - &usart0_clk, - &usart1_clk, - &usart2_clk, - &mmc_clk, - &udc_clk, - &twi_clk, - &spi0_clk, - &spi1_clk, - // ssc - // tc0 .. tc2 - &ohci_clk, - ðer_clk, - &isi_clk, - &usart3_clk, - &usart4_clk, - &usart5_clk, - // tc3 .. tc5 - // irq0 .. irq2 -}; - -/* - * The two programmable clocks. - * You must configure pin multiplexing to bring these signals out. - */ -static struct clk pck0 = { - .name = "pck0", - .pmc_mask = AT91_PMC_PCK0, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 0, -}; -static struct clk pck1 = { - .name = "pck1", - .pmc_mask = AT91_PMC_PCK1, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 1, -}; - -static void __init at91sam9260_register_clocks(void) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) - clk_register(periph_clocks[i]); - - clk_register(&pck0); - clk_register(&pck1); -} - -/* -------------------------------------------------------------------- - * GPIO - * -------------------------------------------------------------------- */ - -static struct at91_gpio_bank at91sam9260_gpio[] = { - { - .id = AT91SAM9260_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, - }, { - .id = AT91SAM9260_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, - }, { - .id = AT91SAM9260_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, - } -}; - -static void at91sam9260_reset(void) -{ - at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); -} - - -/* -------------------------------------------------------------------- - * AT91SAM9260 processor initialization - * -------------------------------------------------------------------- */ - -void __init at91sam9260_initialize(unsigned long main_clock) -{ - /* Map peripherals */ - iotable_init(at91sam9260_io_desc, ARRAY_SIZE(at91sam9260_io_desc)); - - at91_arch_reset = at91sam9260_reset; - at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1) - | (1 << AT91SAM9260_ID_IRQ2); - - /* Init clock subsystem */ - at91_clock_init(main_clock); - - /* Register the processor-specific clocks */ - at91sam9260_register_clocks(); - - /* Register GPIO subsystem */ - at91_gpio_init(at91sam9260_gpio, 3); -} - -/* -------------------------------------------------------------------- - * Interrupt initialization - * -------------------------------------------------------------------- */ - -/* - * The default interrupt priority levels (0 = lowest, 7 = highest). - */ -static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = { - 7, /* Advanced Interrupt Controller */ - 7, /* System Peripherals */ - 0, /* Parallel IO Controller A */ - 0, /* Parallel IO Controller B */ - 0, /* Parallel IO Controller C */ - 0, /* Analog-to-Digital Converter */ - 6, /* USART 0 */ - 6, /* USART 1 */ - 6, /* USART 2 */ - 0, /* Multimedia Card Interface */ - 4, /* USB Device Port */ - 0, /* Two-Wire Interface */ - 6, /* Serial Peripheral Interface 0 */ - 6, /* Serial Peripheral Interface 1 */ - 5, /* Serial Synchronous Controller */ - 0, - 0, - 0, /* Timer Counter 0 */ - 0, /* Timer Counter 1 */ - 0, /* Timer Counter 2 */ - 3, /* USB Host port */ - 3, /* Ethernet */ - 0, /* Image Sensor Interface */ - 6, /* USART 3 */ - 6, /* USART 4 */ - 6, /* USART 5 */ - 0, /* Timer Counter 3 */ - 0, /* Timer Counter 4 */ - 0, /* Timer Counter 5 */ - 0, /* Advanced Interrupt Controller */ - 0, /* Advanced Interrupt Controller */ - 0, /* Advanced Interrupt Controller */ -}; - -void __init at91sam9260_init_interrupts(unsigned int priority[NR_AIC_IRQS]) -{ - if (!priority) - priority = at91sam9260_default_irq_priority; - - /* Initialize the AIC interrupt controller */ - at91_aic_init(priority); - - /* Enable GPIO interrupts */ - at91_gpio_irq_setup(); -} diff --git a/arch/arm/mach-at91rm9200/at91sam9260_devices.c b/arch/arm/mach-at91rm9200/at91sam9260_devices.c deleted file mode 100644 index f338f78eb943..000000000000 --- a/arch/arm/mach-at91rm9200/at91sam9260_devices.c +++ /dev/null @@ -1,867 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/at91sam9260_devices.c - * - * Copyright (C) 2006 Atmel - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ -#include -#include - -#include - -#include -#include -#include -#include -#include - -#include "generic.h" - -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 - -/* -------------------------------------------------------------------- - * USB Host - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) -static u64 ohci_dmamask = 0xffffffffUL; -static struct at91_usbh_data usbh_data; - -static struct resource usbh_resources[] = { - [0] = { - .start = AT91SAM9260_UHP_BASE, - .end = AT91SAM9260_UHP_BASE + SZ_1M - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_UHP, - .end = AT91SAM9260_ID_UHP, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91_usbh_device = { - .name = "at91_ohci", - .id = -1, - .dev = { - .dma_mask = &ohci_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &usbh_data, - }, - .resource = usbh_resources, - .num_resources = ARRAY_SIZE(usbh_resources), -}; - -void __init at91_add_device_usbh(struct at91_usbh_data *data) -{ - if (!data) - return; - - usbh_data = *data; - platform_device_register(&at91_usbh_device); -} -#else -void __init at91_add_device_usbh(struct at91_usbh_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * USB Device (Gadget) - * -------------------------------------------------------------------- */ - -#ifdef CONFIG_USB_GADGET_AT91 -static struct at91_udc_data udc_data; - -static struct resource udc_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_UDP, - .end = AT91SAM9260_BASE_UDP + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_UDP, - .end = AT91SAM9260_ID_UDP, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91_udc_device = { - .name = "at91_udc", - .id = -1, - .dev = { - .platform_data = &udc_data, - }, - .resource = udc_resources, - .num_resources = ARRAY_SIZE(udc_resources), -}; - -void __init at91_add_device_udc(struct at91_udc_data *data) -{ - if (!data) - return; - - if (data->vbus_pin) { - at91_set_gpio_input(data->vbus_pin, 0); - at91_set_deglitch(data->vbus_pin, 1); - } - - /* Pullup pin is handled internally by USB device peripheral */ - - udc_data = *data; - platform_device_register(&at91_udc_device); -} -#else -void __init at91_add_device_udc(struct at91_udc_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * Ethernet - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) -static u64 eth_dmamask = 0xffffffffUL; -static struct at91_eth_data eth_data; - -static struct resource eth_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_EMAC, - .end = AT91SAM9260_BASE_EMAC + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_EMAC, - .end = AT91SAM9260_ID_EMAC, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9260_eth_device = { - .name = "macb", - .id = -1, - .dev = { - .dma_mask = ð_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = ð_data, - }, - .resource = eth_resources, - .num_resources = ARRAY_SIZE(eth_resources), -}; - -void __init at91_add_device_eth(struct at91_eth_data *data) -{ - if (!data) - return; - - if (data->phy_irq_pin) { - at91_set_gpio_input(data->phy_irq_pin, 0); - at91_set_deglitch(data->phy_irq_pin, 1); - } - - /* Pins used for MII and RMII */ - at91_set_A_periph(AT91_PIN_PA19, 0); /* ETXCK_EREFCK */ - at91_set_A_periph(AT91_PIN_PA17, 0); /* ERXDV */ - at91_set_A_periph(AT91_PIN_PA14, 0); /* ERX0 */ - at91_set_A_periph(AT91_PIN_PA15, 0); /* ERX1 */ - at91_set_A_periph(AT91_PIN_PA18, 0); /* ERXER */ - at91_set_A_periph(AT91_PIN_PA16, 0); /* ETXEN */ - at91_set_A_periph(AT91_PIN_PA12, 0); /* ETX0 */ - at91_set_A_periph(AT91_PIN_PA13, 0); /* ETX1 */ - at91_set_A_periph(AT91_PIN_PA21, 0); /* EMDIO */ - at91_set_A_periph(AT91_PIN_PA20, 0); /* EMDC */ - - if (!data->is_rmii) { - at91_set_B_periph(AT91_PIN_PA28, 0); /* ECRS */ - at91_set_B_periph(AT91_PIN_PA29, 0); /* ECOL */ - at91_set_B_periph(AT91_PIN_PA25, 0); /* ERX2 */ - at91_set_B_periph(AT91_PIN_PA26, 0); /* ERX3 */ - at91_set_B_periph(AT91_PIN_PA27, 0); /* ERXCK */ - at91_set_B_periph(AT91_PIN_PA23, 0); /* ETX2 */ - at91_set_B_periph(AT91_PIN_PA24, 0); /* ETX3 */ - at91_set_B_periph(AT91_PIN_PA22, 0); /* ETXER */ - } - - eth_data = *data; - platform_device_register(&at91sam9260_eth_device); -} -#else -void __init at91_add_device_eth(struct at91_eth_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * MMC / SD - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) -static u64 mmc_dmamask = 0xffffffffUL; -static struct at91_mmc_data mmc_data; - -static struct resource mmc_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_MCI, - .end = AT91SAM9260_BASE_MCI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_MCI, - .end = AT91SAM9260_ID_MCI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9260_mmc_device = { - .name = "at91_mci", - .id = -1, - .dev = { - .dma_mask = &mmc_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &mmc_data, - }, - .resource = mmc_resources, - .num_resources = ARRAY_SIZE(mmc_resources), -}; - -void __init at91_add_device_mmc(struct at91_mmc_data *data) -{ - if (!data) - return; - - /* input/irq */ - if (data->det_pin) { - at91_set_gpio_input(data->det_pin, 1); - at91_set_deglitch(data->det_pin, 1); - } - if (data->wp_pin) - at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) - at91_set_gpio_output(data->vcc_pin, 0); - - /* CLK */ - at91_set_A_periph(AT91_PIN_PA8, 0); - - if (data->slot_b) { - /* CMD */ - at91_set_B_periph(AT91_PIN_PA1, 1); - - /* DAT0, maybe DAT1..DAT3 */ - at91_set_B_periph(AT91_PIN_PA0, 1); - if (data->wire4) { - at91_set_B_periph(AT91_PIN_PA5, 1); - at91_set_B_periph(AT91_PIN_PA4, 1); - at91_set_B_periph(AT91_PIN_PA3, 1); - } - } else { - /* CMD */ - at91_set_A_periph(AT91_PIN_PA7, 1); - - /* DAT0, maybe DAT1..DAT3 */ - at91_set_A_periph(AT91_PIN_PA6, 1); - if (data->wire4) { - at91_set_A_periph(AT91_PIN_PA9, 1); - at91_set_A_periph(AT91_PIN_PA10, 1); - at91_set_A_periph(AT91_PIN_PA11, 1); - } - } - - mmc_data = *data; - platform_device_register(&at91sam9260_mmc_device); -} -#else -void __init at91_add_device_mmc(struct at91_mmc_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * NAND / SmartMedia - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) -static struct at91_nand_data nand_data; - -#define NAND_BASE AT91_CHIPSELECT_3 - -static struct resource nand_resources[] = { - { - .start = NAND_BASE, - .end = NAND_BASE + SZ_8M - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device at91sam9260_nand_device = { - .name = "at91_nand", - .id = -1, - .dev = { - .platform_data = &nand_data, - }, - .resource = nand_resources, - .num_resources = ARRAY_SIZE(nand_resources), -}; - -void __init at91_add_device_nand(struct at91_nand_data *data) -{ - unsigned long csa, mode; - - if (!data) - return; - - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC); - - /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); - - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) - | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); - - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); - - if (data->bus_width_16) - mode = AT91_SMC_DBW_16; - else - mode = AT91_SMC_DBW_8; - at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); - - /* enable pin */ - if (data->enable_pin) - at91_set_gpio_output(data->enable_pin, 1); - - /* ready/busy pin */ - if (data->rdy_pin) - at91_set_gpio_input(data->rdy_pin, 1); - - /* card detect pin */ - if (data->det_pin) - at91_set_gpio_input(data->det_pin, 1); - - nand_data = *data; - platform_device_register(&at91sam9260_nand_device); -} -#else -void __init at91_add_device_nand(struct at91_nand_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * TWI (i2c) - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) - -static struct resource twi_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_TWI, - .end = AT91SAM9260_BASE_TWI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_TWI, - .end = AT91SAM9260_ID_TWI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9260_twi_device = { - .name = "at91_i2c", - .id = -1, - .resource = twi_resources, - .num_resources = ARRAY_SIZE(twi_resources), -}; - -void __init at91_add_device_i2c(void) -{ - /* pins used for TWI interface */ - at91_set_A_periph(AT91_PIN_PA23, 0); /* TWD */ - at91_set_multi_drive(AT91_PIN_PA23, 1); - - at91_set_A_periph(AT91_PIN_PA24, 0); /* TWCK */ - at91_set_multi_drive(AT91_PIN_PA24, 1); - - platform_device_register(&at91sam9260_twi_device); -} -#else -void __init at91_add_device_i2c(void) {} -#endif - - -/* -------------------------------------------------------------------- - * SPI - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) -static u64 spi_dmamask = 0xffffffffUL; - -static struct resource spi0_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_SPI0, - .end = AT91SAM9260_BASE_SPI0 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_SPI0, - .end = AT91SAM9260_ID_SPI0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9260_spi0_device = { - .name = "atmel_spi", - .id = 0, - .dev = { - .dma_mask = &spi_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .resource = spi0_resources, - .num_resources = ARRAY_SIZE(spi0_resources), -}; - -static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PC11, AT91_PIN_PC16, AT91_PIN_PC17 }; - -static struct resource spi1_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_SPI1, - .end = AT91SAM9260_BASE_SPI1 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_SPI1, - .end = AT91SAM9260_ID_SPI1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9260_spi1_device = { - .name = "atmel_spi", - .id = 1, - .dev = { - .dma_mask = &spi_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .resource = spi1_resources, - .num_resources = ARRAY_SIZE(spi1_resources), -}; - -static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PC5, AT91_PIN_PC4, AT91_PIN_PC3 }; - -void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) -{ - int i; - unsigned long cs_pin; - short enable_spi0 = 0; - short enable_spi1 = 0; - - /* Choose SPI chip-selects */ - for (i = 0; i < nr_devices; i++) { - if (devices[i].controller_data) - cs_pin = (unsigned long) devices[i].controller_data; - else if (devices[i].bus_num == 0) - cs_pin = spi0_standard_cs[devices[i].chip_select]; - else - cs_pin = spi1_standard_cs[devices[i].chip_select]; - - if (devices[i].bus_num == 0) - enable_spi0 = 1; - else - enable_spi1 = 1; - - /* enable chip-select pin */ - at91_set_gpio_output(cs_pin, 1); - - /* pass chip-select pin to driver */ - devices[i].controller_data = (void *) cs_pin; - } - - spi_register_board_info(devices, nr_devices); - - /* Configure SPI bus(es) */ - if (enable_spi0) { - at91_set_A_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */ - at91_set_A_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */ - at91_set_A_periph(AT91_PIN_PA2, 0); /* SPI1_SPCK */ - - at91_clock_associate("spi0_clk", &at91sam9260_spi0_device.dev, "spi_clk"); - platform_device_register(&at91sam9260_spi0_device); - } - if (enable_spi1) { - at91_set_A_periph(AT91_PIN_PB0, 0); /* SPI1_MISO */ - at91_set_A_periph(AT91_PIN_PB1, 0); /* SPI1_MOSI */ - at91_set_A_periph(AT91_PIN_PB2, 0); /* SPI1_SPCK */ - - at91_clock_associate("spi1_clk", &at91sam9260_spi1_device.dev, "spi_clk"); - platform_device_register(&at91sam9260_spi1_device); - } -} -#else -void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} -#endif - - -/* -------------------------------------------------------------------- - * LEDs - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_LEDS) -u8 at91_leds_cpu; -u8 at91_leds_timer; - -void __init at91_init_leds(u8 cpu_led, u8 timer_led) -{ - at91_leds_cpu = cpu_led; - at91_leds_timer = timer_led; -} -#else -void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} -#endif - - -/* -------------------------------------------------------------------- - * UART - * -------------------------------------------------------------------- */ -#if defined(CONFIG_SERIAL_ATMEL) -static struct resource dbgu_resources[] = { - [0] = { - .start = AT91_VA_BASE_SYS + AT91_DBGU, - .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91_ID_SYS, - .end = AT91_ID_SYS, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data dbgu_data = { - .use_dma_tx = 0, - .use_dma_rx = 0, /* DBGU not capable of receive DMA */ - .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), -}; - -static struct platform_device at91sam9260_dbgu_device = { - .name = "atmel_usart", - .id = 0, - .dev = { - .platform_data = &dbgu_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = dbgu_resources, - .num_resources = ARRAY_SIZE(dbgu_resources), -}; - -static inline void configure_dbgu_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB14, 0); /* DRXD */ - at91_set_A_periph(AT91_PIN_PB15, 1); /* DTXD */ -} - -static struct resource uart0_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_US0, - .end = AT91SAM9260_BASE_US0 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_US0, - .end = AT91SAM9260_ID_US0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart0_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9260_uart0_device = { - .name = "atmel_usart", - .id = 1, - .dev = { - .platform_data = &uart0_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart0_resources, - .num_resources = ARRAY_SIZE(uart0_resources), -}; - -static inline void configure_usart0_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB4, 1); /* TXD0 */ - at91_set_A_periph(AT91_PIN_PB5, 0); /* RXD0 */ - at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS0 */ - at91_set_A_periph(AT91_PIN_PB27, 0); /* CTS0 */ - at91_set_A_periph(AT91_PIN_PB24, 0); /* DTR0 */ - at91_set_A_periph(AT91_PIN_PB22, 0); /* DSR0 */ - at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD0 */ - at91_set_A_periph(AT91_PIN_PB25, 0); /* RI0 */ -} - -static struct resource uart1_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_US1, - .end = AT91SAM9260_BASE_US1 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_US1, - .end = AT91SAM9260_ID_US1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart1_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9260_uart1_device = { - .name = "atmel_usart", - .id = 2, - .dev = { - .platform_data = &uart1_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart1_resources, - .num_resources = ARRAY_SIZE(uart1_resources), -}; - -static inline void configure_usart1_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB6, 1); /* TXD1 */ - at91_set_A_periph(AT91_PIN_PB7, 0); /* RXD1 */ - at91_set_A_periph(AT91_PIN_PB28, 0); /* RTS1 */ - at91_set_A_periph(AT91_PIN_PB29, 0); /* CTS1 */ -} - -static struct resource uart2_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_US2, - .end = AT91SAM9260_BASE_US2 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_US2, - .end = AT91SAM9260_ID_US2, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart2_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9260_uart2_device = { - .name = "atmel_usart", - .id = 3, - .dev = { - .platform_data = &uart2_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart2_resources, - .num_resources = ARRAY_SIZE(uart2_resources), -}; - -static inline void configure_usart2_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB8, 1); /* TXD2 */ - at91_set_A_periph(AT91_PIN_PB9, 0); /* RXD2 */ -} - -static struct resource uart3_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_US3, - .end = AT91SAM9260_BASE_US3 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_US3, - .end = AT91SAM9260_ID_US3, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart3_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9260_uart3_device = { - .name = "atmel_usart", - .id = 4, - .dev = { - .platform_data = &uart3_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart3_resources, - .num_resources = ARRAY_SIZE(uart3_resources), -}; - -static inline void configure_usart3_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB10, 1); /* TXD3 */ - at91_set_A_periph(AT91_PIN_PB11, 0); /* RXD3 */ -} - -static struct resource uart4_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_US4, - .end = AT91SAM9260_BASE_US4 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_US4, - .end = AT91SAM9260_ID_US4, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart4_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9260_uart4_device = { - .name = "atmel_usart", - .id = 5, - .dev = { - .platform_data = &uart4_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart4_resources, - .num_resources = ARRAY_SIZE(uart4_resources), -}; - -static inline void configure_usart4_pins(void) -{ - at91_set_B_periph(AT91_PIN_PA31, 1); /* TXD4 */ - at91_set_B_periph(AT91_PIN_PA30, 0); /* RXD4 */ -} - -static struct resource uart5_resources[] = { - [0] = { - .start = AT91SAM9260_BASE_US5, - .end = AT91SAM9260_BASE_US5 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9260_ID_US5, - .end = AT91SAM9260_ID_US5, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart5_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9260_uart5_device = { - .name = "atmel_usart", - .id = 6, - .dev = { - .platform_data = &uart5_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart5_resources, - .num_resources = ARRAY_SIZE(uart5_resources), -}; - -static inline void configure_usart5_pins(void) -{ - at91_set_A_periph(AT91_PIN_PB12, 1); /* TXD5 */ - at91_set_A_periph(AT91_PIN_PB13, 0); /* RXD5 */ -} - -struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -struct platform_device *atmel_default_console_device; /* the serial console device */ - -void __init at91_init_serial(struct at91_uart_config *config) -{ - int i; - - /* Fill in list of supported UARTs */ - for (i = 0; i < config->nr_tty; i++) { - switch (config->tty_map[i]) { - case 0: - configure_usart0_pins(); - at91_uarts[i] = &at91sam9260_uart0_device; - at91_clock_associate("usart0_clk", &at91sam9260_uart0_device.dev, "usart"); - break; - case 1: - configure_usart1_pins(); - at91_uarts[i] = &at91sam9260_uart1_device; - at91_clock_associate("usart1_clk", &at91sam9260_uart1_device.dev, "usart"); - break; - case 2: - configure_usart2_pins(); - at91_uarts[i] = &at91sam9260_uart2_device; - at91_clock_associate("usart2_clk", &at91sam9260_uart2_device.dev, "usart"); - break; - case 3: - configure_usart3_pins(); - at91_uarts[i] = &at91sam9260_uart3_device; - at91_clock_associate("usart3_clk", &at91sam9260_uart3_device.dev, "usart"); - break; - case 4: - configure_usart4_pins(); - at91_uarts[i] = &at91sam9260_uart4_device; - at91_clock_associate("usart4_clk", &at91sam9260_uart4_device.dev, "usart"); - break; - case 5: - configure_usart5_pins(); - at91_uarts[i] = &at91sam9260_uart5_device; - at91_clock_associate("usart5_clk", &at91sam9260_uart5_device.dev, "usart"); - break; - case 6: - configure_dbgu_pins(); - at91_uarts[i] = &at91sam9260_dbgu_device; - at91_clock_associate("mck", &at91sam9260_dbgu_device.dev, "usart"); - break; - default: - continue; - } - at91_uarts[i]->id = i; /* update ID number to mapped ID */ - } - - /* Set serial console device */ - if (config->console_tty < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[config->console_tty]; - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); -} - -void __init at91_add_device_serial(void) -{ - int i; - - for (i = 0; i < ATMEL_MAX_UART; i++) { - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -} -#else -void __init at91_init_serial(struct at91_uart_config *config) {} -void __init at91_add_device_serial(void) {} -#endif - - -/* -------------------------------------------------------------------- */ -/* - * These devices are always present and don't need any board-specific - * setup. - */ -static int __init at91_add_standard_devices(void) -{ - return 0; -} - -arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91rm9200/at91sam9261.c b/arch/arm/mach-at91rm9200/at91sam9261.c deleted file mode 100644 index d242bb885c6d..000000000000 --- a/arch/arm/mach-at91rm9200/at91sam9261.c +++ /dev/null @@ -1,290 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/at91sam9261.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#include - -#include -#include -#include -#include -#include - -#include "generic.h" -#include "clock.h" - -static struct map_desc at91sam9261_io_desc[] __initdata = { - { - .virtual = AT91_VA_BASE_SYS, - .pfn = __phys_to_pfn(AT91_BASE_SYS), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_IO_VIRT_BASE - AT91SAM9261_SRAM_SIZE, - .pfn = __phys_to_pfn(AT91SAM9261_SRAM_BASE), - .length = AT91SAM9261_SRAM_SIZE, - .type = MT_DEVICE, - }, -}; - -/* -------------------------------------------------------------------- - * Clocks - * -------------------------------------------------------------------- */ - -/* - * The peripheral clocks. - */ -static struct clk pioA_clk = { - .name = "pioA_clk", - .pmc_mask = 1 << AT91SAM9261_ID_PIOA, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioB_clk = { - .name = "pioB_clk", - .pmc_mask = 1 << AT91SAM9261_ID_PIOB, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk pioC_clk = { - .name = "pioC_clk", - .pmc_mask = 1 << AT91SAM9261_ID_PIOC, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart0_clk = { - .name = "usart0_clk", - .pmc_mask = 1 << AT91SAM9261_ID_US0, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart1_clk = { - .name = "usart1_clk", - .pmc_mask = 1 << AT91SAM9261_ID_US1, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk usart2_clk = { - .name = "usart2_clk", - .pmc_mask = 1 << AT91SAM9261_ID_US2, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk mmc_clk = { - .name = "mci_clk", - .pmc_mask = 1 << AT91SAM9261_ID_MCI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk udc_clk = { - .name = "udc_clk", - .pmc_mask = 1 << AT91SAM9261_ID_UDP, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk twi_clk = { - .name = "twi_clk", - .pmc_mask = 1 << AT91SAM9261_ID_TWI, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk spi0_clk = { - .name = "spi0_clk", - .pmc_mask = 1 << AT91SAM9261_ID_SPI0, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk spi1_clk = { - .name = "spi1_clk", - .pmc_mask = 1 << AT91SAM9261_ID_SPI1, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk ohci_clk = { - .name = "ohci_clk", - .pmc_mask = 1 << AT91SAM9261_ID_UHP, - .type = CLK_TYPE_PERIPHERAL, -}; -static struct clk lcdc_clk = { - .name = "lcdc_clk", - .pmc_mask = 1 << AT91SAM9261_ID_LCDC, - .type = CLK_TYPE_PERIPHERAL, -}; - -static struct clk *periph_clocks[] __initdata = { - &pioA_clk, - &pioB_clk, - &pioC_clk, - &usart0_clk, - &usart1_clk, - &usart2_clk, - &mmc_clk, - &udc_clk, - &twi_clk, - &spi0_clk, - &spi1_clk, - // ssc 0 .. ssc2 - // tc0 .. tc2 - &ohci_clk, - &lcdc_clk, - // irq0 .. irq2 -}; - -/* - * The four programmable clocks. - * You must configure pin multiplexing to bring these signals out. - */ -static struct clk pck0 = { - .name = "pck0", - .pmc_mask = AT91_PMC_PCK0, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 0, -}; -static struct clk pck1 = { - .name = "pck1", - .pmc_mask = AT91_PMC_PCK1, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 1, -}; -static struct clk pck2 = { - .name = "pck2", - .pmc_mask = AT91_PMC_PCK2, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 2, -}; -static struct clk pck3 = { - .name = "pck3", - .pmc_mask = AT91_PMC_PCK3, - .type = CLK_TYPE_PROGRAMMABLE, - .id = 3, -}; - -/* HClocks */ -static struct clk hck0 = { - .name = "hck0", - .pmc_mask = AT91_PMC_HCK0, - .type = CLK_TYPE_SYSTEM, - .id = 0, -}; -static struct clk hck1 = { - .name = "hck1", - .pmc_mask = AT91_PMC_HCK1, - .type = CLK_TYPE_SYSTEM, - .id = 1, -}; - -static void __init at91sam9261_register_clocks(void) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) - clk_register(periph_clocks[i]); - - clk_register(&pck0); - clk_register(&pck1); - clk_register(&pck2); - clk_register(&pck3); - - clk_register(&hck0); - clk_register(&hck1); -} - -/* -------------------------------------------------------------------- - * GPIO - * -------------------------------------------------------------------- */ - -static struct at91_gpio_bank at91sam9261_gpio[] = { - { - .id = AT91SAM9261_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, - }, { - .id = AT91SAM9261_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, - }, { - .id = AT91SAM9261_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, - } -}; - -static void at91sam9261_reset(void) -{ - at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); -} - - -/* -------------------------------------------------------------------- - * AT91SAM9261 processor initialization - * -------------------------------------------------------------------- */ - -void __init at91sam9261_initialize(unsigned long main_clock) -{ - /* Map peripherals */ - iotable_init(at91sam9261_io_desc, ARRAY_SIZE(at91sam9261_io_desc)); - - at91_arch_reset = at91sam9261_reset; - at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1) - | (1 << AT91SAM9261_ID_IRQ2); - - /* Init clock subsystem */ - at91_clock_init(main_clock); - - /* Register the processor-specific clocks */ - at91sam9261_register_clocks(); - - /* Register GPIO subsystem */ - at91_gpio_init(at91sam9261_gpio, 3); -} - -/* -------------------------------------------------------------------- - * Interrupt initialization - * -------------------------------------------------------------------- */ - -/* - * The default interrupt priority levels (0 = lowest, 7 = highest). - */ -static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = { - 7, /* Advanced Interrupt Controller */ - 7, /* System Peripherals */ - 0, /* Parallel IO Controller A */ - 0, /* Parallel IO Controller B */ - 0, /* Parallel IO Controller C */ - 0, - 6, /* USART 0 */ - 6, /* USART 1 */ - 6, /* USART 2 */ - 0, /* Multimedia Card Interface */ - 4, /* USB Device Port */ - 0, /* Two-Wire Interface */ - 6, /* Serial Peripheral Interface 0 */ - 6, /* Serial Peripheral Interface 1 */ - 5, /* Serial Synchronous Controller 0 */ - 5, /* Serial Synchronous Controller 1 */ - 5, /* Serial Synchronous Controller 2 */ - 0, /* Timer Counter 0 */ - 0, /* Timer Counter 1 */ - 0, /* Timer Counter 2 */ - 3, /* USB Host port */ - 3, /* LCD Controller */ - 0, - 0, - 0, - 0, - 0, - 0, - 0, - 0, /* Advanced Interrupt Controller */ - 0, /* Advanced Interrupt Controller */ - 0, /* Advanced Interrupt Controller */ -}; - -void __init at91sam9261_init_interrupts(unsigned int priority[NR_AIC_IRQS]) -{ - if (!priority) - priority = at91sam9261_default_irq_priority; - - /* Initialize the AIC interrupt controller */ - at91_aic_init(priority); - - /* Enable GPIO interrupts */ - at91_gpio_irq_setup(); -} diff --git a/arch/arm/mach-at91rm9200/at91sam9261_devices.c b/arch/arm/mach-at91rm9200/at91sam9261_devices.c deleted file mode 100644 index ed1d79081b35..000000000000 --- a/arch/arm/mach-at91rm9200/at91sam9261_devices.c +++ /dev/null @@ -1,741 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/at91sam9261_devices.c - * - * Copyright (C) 2005 Thibaut VARENE - * Copyright (C) 2005 David Brownell - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ -#include -#include - -#include - -#include -#include -#include -#include -#include - -#include "generic.h" - -#define SZ_512 0x00000200 -#define SZ_256 0x00000100 -#define SZ_16 0x00000010 - -/* -------------------------------------------------------------------- - * USB Host - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) -static u64 ohci_dmamask = 0xffffffffUL; -static struct at91_usbh_data usbh_data; - -static struct resource usbh_resources[] = { - [0] = { - .start = AT91SAM9261_UHP_BASE, - .end = AT91SAM9261_UHP_BASE + SZ_1M - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_UHP, - .end = AT91SAM9261_ID_UHP, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9261_usbh_device = { - .name = "at91_ohci", - .id = -1, - .dev = { - .dma_mask = &ohci_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &usbh_data, - }, - .resource = usbh_resources, - .num_resources = ARRAY_SIZE(usbh_resources), -}; - -void __init at91_add_device_usbh(struct at91_usbh_data *data) -{ - if (!data) - return; - - usbh_data = *data; - platform_device_register(&at91sam9261_usbh_device); -} -#else -void __init at91_add_device_usbh(struct at91_usbh_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * USB Device (Gadget) - * -------------------------------------------------------------------- */ - -#ifdef CONFIG_USB_GADGET_AT91 -static struct at91_udc_data udc_data; - -static struct resource udc_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_UDP, - .end = AT91SAM9261_BASE_UDP + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_UDP, - .end = AT91SAM9261_ID_UDP, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9261_udc_device = { - .name = "at91_udc", - .id = -1, - .dev = { - .platform_data = &udc_data, - }, - .resource = udc_resources, - .num_resources = ARRAY_SIZE(udc_resources), -}; - -void __init at91_add_device_udc(struct at91_udc_data *data) -{ - unsigned long x; - - if (!data) - return; - - if (data->vbus_pin) { - at91_set_gpio_input(data->vbus_pin, 0); - at91_set_deglitch(data->vbus_pin, 1); - } - - /* Pullup pin is handled internally */ - x = at91_sys_read(AT91_MATRIX_USBPUCR); - at91_sys_write(AT91_MATRIX_USBPUCR, x | AT91_MATRIX_USBPUCR_PUON); - - udc_data = *data; - platform_device_register(&at91sam9261_udc_device); -} -#else -void __init at91_add_device_udc(struct at91_udc_data *data) {} -#endif - -/* -------------------------------------------------------------------- - * MMC / SD - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) -static u64 mmc_dmamask = 0xffffffffUL; -static struct at91_mmc_data mmc_data; - -static struct resource mmc_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_MCI, - .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_MCI, - .end = AT91SAM9261_ID_MCI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9261_mmc_device = { - .name = "at91_mci", - .id = -1, - .dev = { - .dma_mask = &mmc_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &mmc_data, - }, - .resource = mmc_resources, - .num_resources = ARRAY_SIZE(mmc_resources), -}; - -void __init at91_add_device_mmc(struct at91_mmc_data *data) -{ - if (!data) - return; - - /* input/irq */ - if (data->det_pin) { - at91_set_gpio_input(data->det_pin, 1); - at91_set_deglitch(data->det_pin, 1); - } - if (data->wp_pin) - at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) - at91_set_gpio_output(data->vcc_pin, 0); - - /* CLK */ - at91_set_B_periph(AT91_PIN_PA2, 0); - - /* CMD */ - at91_set_B_periph(AT91_PIN_PA1, 1); - - /* DAT0, maybe DAT1..DAT3 */ - at91_set_B_periph(AT91_PIN_PA0, 1); - if (data->wire4) { - at91_set_B_periph(AT91_PIN_PA4, 1); - at91_set_B_periph(AT91_PIN_PA5, 1); - at91_set_B_periph(AT91_PIN_PA6, 1); - } - - mmc_data = *data; - platform_device_register(&at91sam9261_mmc_device); -} -#else -void __init at91_add_device_mmc(struct at91_mmc_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * NAND / SmartMedia - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) -static struct at91_nand_data nand_data; - -#define NAND_BASE AT91_CHIPSELECT_3 - -static struct resource nand_resources[] = { - { - .start = NAND_BASE, - .end = NAND_BASE + SZ_256M - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device at91_nand_device = { - .name = "at91_nand", - .id = -1, - .dev = { - .platform_data = &nand_data, - }, - .resource = nand_resources, - .num_resources = ARRAY_SIZE(nand_resources), -}; - -void __init at91_add_device_nand(struct at91_nand_data *data) -{ - unsigned long csa, mode; - - if (!data) - return; - - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC); - - /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); - - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5) - | AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5)); - - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); - - if (data->bus_width_16) - mode = AT91_SMC_DBW_16; - else - mode = AT91_SMC_DBW_8; - at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1)); - - /* enable pin */ - if (data->enable_pin) - at91_set_gpio_output(data->enable_pin, 1); - - /* ready/busy pin */ - if (data->rdy_pin) - at91_set_gpio_input(data->rdy_pin, 1); - - /* card detect pin */ - if (data->det_pin) - at91_set_gpio_input(data->det_pin, 1); - - at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ - at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */ - - nand_data = *data; - platform_device_register(&at91_nand_device); -} - -#else -void __init at91_add_device_nand(struct at91_nand_data *data) {} -#endif - - -/* -------------------------------------------------------------------- - * TWI (i2c) - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) - -static struct resource twi_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_TWI, - .end = AT91SAM9261_BASE_TWI + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_TWI, - .end = AT91SAM9261_ID_TWI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9261_twi_device = { - .name = "at91_i2c", - .id = -1, - .resource = twi_resources, - .num_resources = ARRAY_SIZE(twi_resources), -}; - -void __init at91_add_device_i2c(void) -{ - /* pins used for TWI interface */ - at91_set_A_periph(AT91_PIN_PA7, 0); /* TWD */ - at91_set_multi_drive(AT91_PIN_PA7, 1); - - at91_set_A_periph(AT91_PIN_PA8, 0); /* TWCK */ - at91_set_multi_drive(AT91_PIN_PA8, 1); - - platform_device_register(&at91sam9261_twi_device); -} -#else -void __init at91_add_device_i2c(void) {} -#endif - - -/* -------------------------------------------------------------------- - * SPI - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) -static u64 spi_dmamask = 0xffffffffUL; - -static struct resource spi0_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_SPI0, - .end = AT91SAM9261_BASE_SPI0 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_SPI0, - .end = AT91SAM9261_ID_SPI0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9261_spi0_device = { - .name = "atmel_spi", - .id = 0, - .dev = { - .dma_mask = &spi_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .resource = spi0_resources, - .num_resources = ARRAY_SIZE(spi0_resources), -}; - -static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 }; - -static struct resource spi1_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_SPI1, - .end = AT91SAM9261_BASE_SPI1 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_SPI1, - .end = AT91SAM9261_ID_SPI1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device at91sam9261_spi1_device = { - .name = "atmel_spi", - .id = 1, - .dev = { - .dma_mask = &spi_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .resource = spi1_resources, - .num_resources = ARRAY_SIZE(spi1_resources), -}; - -static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB28, AT91_PIN_PA24, AT91_PIN_PA25, AT91_PIN_PA26 }; - -void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) -{ - int i; - unsigned long cs_pin; - short enable_spi0 = 0; - short enable_spi1 = 0; - - /* Choose SPI chip-selects */ - for (i = 0; i < nr_devices; i++) { - if (devices[i].controller_data) - cs_pin = (unsigned long) devices[i].controller_data; - else if (devices[i].bus_num == 0) - cs_pin = spi0_standard_cs[devices[i].chip_select]; - else - cs_pin = spi1_standard_cs[devices[i].chip_select]; - - if (devices[i].bus_num == 0) - enable_spi0 = 1; - else - enable_spi1 = 1; - - /* enable chip-select pin */ - at91_set_gpio_output(cs_pin, 1); - - /* pass chip-select pin to driver */ - devices[i].controller_data = (void *) cs_pin; - } - - spi_register_board_info(devices, nr_devices); - - /* Configure SPI bus(es) */ - if (enable_spi0) { - at91_set_A_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */ - at91_set_A_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */ - at91_set_A_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */ - - at91_clock_associate("spi0_clk", &at91sam9261_spi0_device.dev, "spi_clk"); - platform_device_register(&at91sam9261_spi0_device); - } - if (enable_spi1) { - at91_set_A_periph(AT91_PIN_PB30, 0); /* SPI1_MISO */ - at91_set_A_periph(AT91_PIN_PB31, 0); /* SPI1_MOSI */ - at91_set_A_periph(AT91_PIN_PB29, 0); /* SPI1_SPCK */ - - at91_clock_associate("spi1_clk", &at91sam9261_spi1_device.dev, "spi_clk"); - platform_device_register(&at91sam9261_spi1_device); - } -} -#else -void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} -#endif - - -/* -------------------------------------------------------------------- - * LCD Controller - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_FB_AT91) || defined(CONFIG_FB_AT91_MODULE) -static u64 lcdc_dmamask = 0xffffffffUL; -static struct at91fb_info lcdc_data; - -static struct resource lcdc_resources[] = { - [0] = { - .start = AT91SAM9261_LCDC_BASE, - .end = AT91SAM9261_LCDC_BASE + SZ_4K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_LCDC, - .end = AT91SAM9261_ID_LCDC, - .flags = IORESOURCE_IRQ, - }, -#if defined(CONFIG_FB_INTSRAM) - [2] = { - .start = AT91SAM9261_SRAM_BASE, - .end = AT91SAM9261_SRAM_BASE + AT91SAM9261_SRAM_SIZE - 1, - .flags = IORESOURCE_MEM, - }, -#endif -}; - -static struct platform_device at91_lcdc_device = { - .name = "at91-fb", - .id = 0, - .dev = { - .dma_mask = &lcdc_dmamask, - .coherent_dma_mask = 0xffffffff, - .platform_data = &lcdc_data, - }, - .resource = lcdc_resources, - .num_resources = ARRAY_SIZE(lcdc_resources), -}; - -void __init at91_add_device_lcdc(struct at91fb_info *data) -{ - if (!data) { - return; - } - - at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ - at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ - at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ - at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */ - at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */ - at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */ - at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */ - at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */ - at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */ - at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */ - at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */ - at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */ - at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */ - at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */ - at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */ - at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */ - at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */ - at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */ - at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */ - at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */ - at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ - at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ - - lcdc_data = *data; - platform_device_register(&at91_lcdc_device); -} -#else -void __init at91_add_device_lcdc(struct at91fb_info *data) {} -#endif - - -/* -------------------------------------------------------------------- - * LEDs - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_LEDS) -u8 at91_leds_cpu; -u8 at91_leds_timer; - -void __init at91_init_leds(u8 cpu_led, u8 timer_led) -{ - at91_leds_cpu = cpu_led; - at91_leds_timer = timer_led; -} -#else -void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} -#endif - - -/* -------------------------------------------------------------------- - * UART - * -------------------------------------------------------------------- */ - -#if defined(CONFIG_SERIAL_ATMEL) -static struct resource dbgu_resources[] = { - [0] = { - .start = AT91_VA_BASE_SYS + AT91_DBGU, - .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91_ID_SYS, - .end = AT91_ID_SYS, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data dbgu_data = { - .use_dma_tx = 0, - .use_dma_rx = 0, /* DBGU not capable of receive DMA */ - .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), -}; - -static struct platform_device at91sam9261_dbgu_device = { - .name = "atmel_usart", - .id = 0, - .dev = { - .platform_data = &dbgu_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = dbgu_resources, - .num_resources = ARRAY_SIZE(dbgu_resources), -}; - -static inline void configure_dbgu_pins(void) -{ - at91_set_A_periph(AT91_PIN_PA9, 0); /* DRXD */ - at91_set_A_periph(AT91_PIN_PA10, 1); /* DTXD */ -} - -static struct resource uart0_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_US0, - .end = AT91SAM9261_BASE_US0 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_US0, - .end = AT91SAM9261_ID_US0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart0_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9261_uart0_device = { - .name = "atmel_usart", - .id = 1, - .dev = { - .platform_data = &uart0_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart0_resources, - .num_resources = ARRAY_SIZE(uart0_resources), -}; - -static inline void configure_usart0_pins(void) -{ - at91_set_A_periph(AT91_PIN_PC8, 1); /* TXD0 */ - at91_set_A_periph(AT91_PIN_PC9, 0); /* RXD0 */ - at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */ - at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */ -} - -static struct resource uart1_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_US1, - .end = AT91SAM9261_BASE_US1 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_US1, - .end = AT91SAM9261_ID_US1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart1_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9261_uart1_device = { - .name = "atmel_usart", - .id = 2, - .dev = { - .platform_data = &uart1_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart1_resources, - .num_resources = ARRAY_SIZE(uart1_resources), -}; - -static inline void configure_usart1_pins(void) -{ - at91_set_A_periph(AT91_PIN_PC12, 1); /* TXD1 */ - at91_set_A_periph(AT91_PIN_PC13, 0); /* RXD1 */ -} - -static struct resource uart2_resources[] = { - [0] = { - .start = AT91SAM9261_BASE_US2, - .end = AT91SAM9261_BASE_US2 + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = AT91SAM9261_ID_US2, - .end = AT91SAM9261_ID_US2, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct atmel_uart_data uart2_data = { - .use_dma_tx = 1, - .use_dma_rx = 1, -}; - -static struct platform_device at91sam9261_uart2_device = { - .name = "atmel_usart", - .id = 3, - .dev = { - .platform_data = &uart2_data, - .coherent_dma_mask = 0xffffffff, - }, - .resource = uart2_resources, - .num_resources = ARRAY_SIZE(uart2_resources), -}; - -static inline void configure_usart2_pins(void) -{ - at91_set_A_periph(AT91_PIN_PC15, 0); /* RXD2 */ - at91_set_A_periph(AT91_PIN_PC14, 1); /* TXD2 */ -} - -struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -struct platform_device *atmel_default_console_device; /* the serial console device */ - -void __init at91_init_serial(struct at91_uart_config *config) -{ - int i; - - /* Fill in list of supported UARTs */ - for (i = 0; i < config->nr_tty; i++) { - switch (config->tty_map[i]) { - case 0: - configure_usart0_pins(); - at91_uarts[i] = &at91sam9261_uart0_device; - at91_clock_associate("usart0_clk", &at91sam9261_uart0_device.dev, "usart"); - break; - case 1: - configure_usart1_pins(); - at91_uarts[i] = &at91sam9261_uart1_device; - at91_clock_associate("usart1_clk", &at91sam9261_uart1_device.dev, "usart"); - break; - case 2: - configure_usart2_pins(); - at91_uarts[i] = &at91sam9261_uart2_device; - at91_clock_associate("usart2_clk", &at91sam9261_uart2_device.dev, "usart"); - break; - case 3: - configure_dbgu_pins(); - at91_uarts[i] = &at91sam9261_dbgu_device; - at91_clock_associate("mck", &at91sam9261_dbgu_device.dev, "usart"); - break; - default: - continue; - } - at91_uarts[i]->id = i; /* update ID number to mapped ID */ - } - - /* Set serial console device */ - if (config->console_tty < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[config->console_tty]; - if (!atmel_default_console_device) - printk(KERN_INFO "AT91: No default serial console defined.\n"); -} - -void __init at91_add_device_serial(void) -{ - int i; - - for (i = 0; i < ATMEL_MAX_UART; i++) { - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -} -#else -void __init at91_init_serial(struct at91_uart_config *config) {} -void __init at91_add_device_serial(void) {} -#endif - - -/* -------------------------------------------------------------------- */ - -/* - * These devices are always present and don't need any board-specific - * setup. - */ -static int __init at91_add_standard_devices(void) -{ - return 0; -} - -arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91rm9200/at91sam926x_time.c b/arch/arm/mach-at91rm9200/at91sam926x_time.c deleted file mode 100644 index 99df5f6ee42e..000000000000 --- a/arch/arm/mach-at91rm9200/at91sam926x_time.c +++ /dev/null @@ -1,114 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/at91sam926x_time.c - * - * Copyright (C) 2005-2006 M. Amine SAYA, ATMEL Rousset, France - * Revision 2005 M. Nicolas Diremdjian, ATMEL Rousset, France - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - - -#define PIT_CPIV(x) ((x) & AT91_PIT_CPIV) -#define PIT_PICNT(x) (((x) & AT91_PIT_PICNT) >> 20) - -/* - * Returns number of microseconds since last timer interrupt. Note that interrupts - * will have been disabled by do_gettimeofday() - * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. - * 'tick' is usecs per jiffy (linux/timex.h). - */ -static unsigned long at91sam926x_gettimeoffset(void) -{ - unsigned long elapsed; - unsigned long t = at91_sys_read(AT91_PIT_PIIR); - - elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t); /* hardware clock cycles */ - - return (unsigned long)(elapsed * 1000000) / LATCH; -} - -/* - * IRQ handler for the timer. - */ -static irqreturn_t at91sam926x_timer_interrupt(int irq, void *dev_id) -{ - volatile long nr_ticks; - - if (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS) { /* This is a shared interrupt */ - write_seqlock(&xtime_lock); - - /* Get number to ticks performed before interrupt and clear PIT interrupt */ - nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); - do { - timer_tick(); - nr_ticks--; - } while (nr_ticks); - - write_sequnlock(&xtime_lock); - return IRQ_HANDLED; - } else - return IRQ_NONE; /* not handled */ -} - -static struct irqaction at91sam926x_timer_irq = { - .name = "at91_tick", - .flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER, - .handler = at91sam926x_timer_interrupt -}; - -void at91sam926x_timer_reset(void) -{ - /* Disable timer */ - at91_sys_write(AT91_PIT_MR, 0); - - /* Clear any pending interrupts */ - (void) at91_sys_read(AT91_PIT_PIVR); - - /* Set Period Interval timer and enable its interrupt */ - at91_sys_write(AT91_PIT_MR, (LATCH & AT91_PIT_PIV) | AT91_PIT_PITIEN | AT91_PIT_PITEN); -} - -/* - * Set up timer interrupt. - */ -void __init at91sam926x_timer_init(void) -{ - /* Initialize and enable the timer */ - at91sam926x_timer_reset(); - - /* Make IRQs happen for the system timer. */ - setup_irq(AT91_ID_SYS, &at91sam926x_timer_irq); -} - -#ifdef CONFIG_PM -static void at91sam926x_timer_suspend(void) -{ - /* Disable timer */ - at91_sys_write(AT91_PIT_MR, 0); -} -#else -#define at91sam926x_timer_suspend NULL -#endif - -struct sys_timer at91sam926x_timer = { - .init = at91sam926x_timer_init, - .offset = at91sam926x_gettimeoffset, - .suspend = at91sam926x_timer_suspend, - .resume = at91sam926x_timer_reset, -}; - diff --git a/arch/arm/mach-at91rm9200/board-1arm.c b/arch/arm/mach-at91rm9200/board-1arm.c deleted file mode 100644 index 971c3e2d8e36..000000000000 --- a/arch/arm/mach-at91rm9200/board-1arm.c +++ /dev/null @@ -1,102 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-1arm.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata onearm_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 4, 0, 1, -1, -1 }, /* ttyS0, ..., ttyS4 */ -}; - -static void __init onearm_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_PQFP); - - /* Setup the serial ports and console */ - at91_init_serial(&onearm_uart_config); -} - -static void __init onearm_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata onearm_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata onearm_usbh_data = { - .ports = 1, -}; - -static struct at91_udc_data __initdata onearm_udc_data = { - .vbus_pin = AT91_PIN_PC2, - .pullup_pin = AT91_PIN_PC3, -}; - -static void __init onearm_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&onearm_eth_data); - /* USB Host */ - at91_add_device_usbh(&onearm_usbh_data); - /* USB Device */ - at91_add_device_udc(&onearm_udc_data); -} - -MACHINE_START(ONEARM, "Ajeco 1ARM single board computer") - /* Maintainer: Lennert Buytenhek */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = onearm_map_io, - .init_irq = onearm_init_irq, - .init_machine = onearm_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-carmeva.c b/arch/arm/mach-at91rm9200/board-carmeva.c deleted file mode 100644 index 654f0379550a..000000000000 --- a/arch/arm/mach-at91rm9200/board-carmeva.c +++ /dev/null @@ -1,149 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-carmeva.c - * - * Copyright (c) 2005 Peer Georgi - * Conitec Datasystems - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata carmeva_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init carmeva_map_io(void) -{ - /* Initialize processor: 20.000 MHz crystal */ - at91rm9200_initialize(20000000, AT91RM9200_BGA); - - /* Setup the serial ports and console */ - at91_init_serial(&carmeva_uart_config); -} - -static void __init carmeva_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata carmeva_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata carmeva_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata carmeva_udc_data = { - .vbus_pin = AT91_PIN_PD12, - .pullup_pin = AT91_PIN_PD9, -}; - -/* FIXME: user dependend */ -// static struct at91_cf_data __initdata carmeva_cf_data = { -// .det_pin = AT91_PIN_PB0, -// .rst_pin = AT91_PIN_PC5, - // .irq_pin = ... not connected - // .vcc_pin = ... always powered -// }; - -static struct at91_mmc_data __initdata carmeva_mmc_data = { - .slot_b = 0, - .wire4 = 1, - .det_pin = AT91_PIN_PB10, - .wp_pin = AT91_PIN_PC14, -}; - -static struct spi_board_info carmeva_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 10 * 1000 * 1000, - }, - { /* User accessable spi - cs1 (250KHz) */ - .modalias = "spi-cs1", - .chip_select = 1, - .max_speed_hz = 250 * 1000, - }, - { /* User accessable spi - cs2 (1MHz) */ - .modalias = "spi-cs2", - .chip_select = 2, - .max_speed_hz = 1 * 1000 * 1000, - }, - { /* User accessable spi - cs3 (10MHz) */ - .modalias = "spi-cs3", - .chip_select = 3, - .max_speed_hz = 10 * 1000 * 1000, - }, -}; - -static void __init carmeva_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&carmeva_eth_data); - /* USB Host */ - at91_add_device_usbh(&carmeva_usbh_data); - /* USB Device */ - at91_add_device_udc(&carmeva_udc_data); - /* I2C */ - at91_add_device_i2c(); - /* SPI */ - at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices)); - /* Compact Flash */ -// at91_add_device_cf(&carmeva_cf_data); - /* MMC */ - at91_add_device_mmc(&carmeva_mmc_data); -} - -MACHINE_START(CARMEVA, "Carmeva") - /* Maintainer: Conitec Datasystems */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = carmeva_map_io, - .init_irq = carmeva_init_irq, - .init_machine = carmeva_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-csb337.c b/arch/arm/mach-at91rm9200/board-csb337.c deleted file mode 100644 index b8bb8052607a..000000000000 --- a/arch/arm/mach-at91rm9200/board-csb337.c +++ /dev/null @@ -1,145 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-csb337.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata csb337_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init csb337_map_io(void) -{ - /* Initialize processor: 3.6864 MHz crystal */ - at91rm9200_initialize(3686400, AT91RM9200_BGA); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); - - /* Setup the serial ports and console */ - at91_init_serial(&csb337_uart_config); -} - -static void __init csb337_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata csb337_eth_data = { - .phy_irq_pin = AT91_PIN_PC2, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata csb337_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata csb337_udc_data = { - // this has no VBUS sensing pin - .pullup_pin = AT91_PIN_PA24, -}; - -static struct at91_cf_data __initdata csb337_cf_data = { - /* - * connector P4 on the CSB 337 mates to - * connector P8 on the CSB 300CF - */ - - /* CSB337 specific */ - .det_pin = AT91_PIN_PC3, - - /* CSB300CF specific */ - .irq_pin = AT91_PIN_PA19, - .vcc_pin = AT91_PIN_PD0, - .rst_pin = AT91_PIN_PD2, -}; - -static struct at91_mmc_data __initdata csb337_mmc_data = { - .det_pin = AT91_PIN_PD5, - .slot_b = 0, - .wire4 = 1, - .wp_pin = AT91_PIN_PD6, -}; - -static struct spi_board_info csb337_spi_devices[] = { - { /* CAN controller */ - .modalias = "sak82c900", - .chip_select = 0, - .max_speed_hz = 6 * 1000 * 1000, - }, -}; - -static void __init csb337_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&csb337_eth_data); - /* USB Host */ - at91_add_device_usbh(&csb337_usbh_data); - /* USB Device */ - at91_add_device_udc(&csb337_udc_data); - /* I2C */ - at91_add_device_i2c(); - /* Compact Flash */ - at91_set_gpio_input(AT91_PIN_PB22, 1); /* IOIS16 */ - at91_add_device_cf(&csb337_cf_data); - /* SPI */ - at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); - /* MMC */ - at91_add_device_mmc(&csb337_mmc_data); -} - -MACHINE_START(CSB337, "Cogent CSB337") - /* Maintainer: Bill Gatliff */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = csb337_map_io, - .init_irq = csb337_init_irq, - .init_machine = csb337_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-csb637.c b/arch/arm/mach-at91rm9200/board-csb637.c deleted file mode 100644 index a29fa0e822ce..000000000000 --- a/arch/arm/mach-at91rm9200/board-csb637.c +++ /dev/null @@ -1,109 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-csb637.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata csb637_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init csb637_map_io(void) -{ - /* Initialize processor: 3.6864 MHz crystal */ - at91rm9200_initialize(3686400, AT91RM9200_BGA); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); - - /* Setup the serial ports and console */ - at91_init_serial(&csb637_uart_config); -} - -static void __init csb637_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata csb637_eth_data = { - .phy_irq_pin = AT91_PIN_PC0, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata csb637_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata csb637_udc_data = { - .vbus_pin = AT91_PIN_PB28, - .pullup_pin = AT91_PIN_PB1, -}; - -static void __init csb637_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&csb637_eth_data); - /* USB Host */ - at91_add_device_usbh(&csb637_usbh_data); - /* USB Device */ - at91_add_device_udc(&csb637_udc_data); - /* I2C */ - at91_add_device_i2c(); - /* SPI */ - at91_add_device_spi(NULL, 0); -} - -MACHINE_START(CSB637, "Cogent CSB637") - /* Maintainer: Bill Gatliff */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = csb637_map_io, - .init_irq = csb637_init_irq, - .init_machine = csb637_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-dk.c b/arch/arm/mach-at91rm9200/board-dk.c deleted file mode 100644 index 7522bf91bce8..000000000000 --- a/arch/arm/mach-at91rm9200/board-dk.c +++ /dev/null @@ -1,216 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-dk.c - * - * Copyright (C) 2005 SAN People - * - * Epson S1D framebuffer glue code is: - * Copyright (C) 2005 Thibaut VARENE - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata dk_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init dk_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_BGA); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); - - /* Setup the serial ports and console */ - at91_init_serial(&dk_uart_config); -} - -static void __init dk_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata dk_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata dk_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata dk_udc_data = { - .vbus_pin = AT91_PIN_PD4, - .pullup_pin = AT91_PIN_PD5, -}; - -static struct at91_cf_data __initdata dk_cf_data = { - .det_pin = AT91_PIN_PB0, - .rst_pin = AT91_PIN_PC5, - // .irq_pin = ... not connected - // .vcc_pin = ... always powered -}; - -static struct at91_mmc_data __initdata dk_mmc_data = { - .slot_b = 0, - .wire4 = 1, -}; - -static struct spi_board_info dk_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - }, - { /* UR6HCPS2-SP40 PS2-to-SPI adapter */ - .modalias = "ur6hcps2", - .chip_select = 1, - .max_speed_hz = 250 * 1000, - }, - { /* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */ - .modalias = "tlv1504", - .chip_select = 2, - .max_speed_hz = 20 * 1000 * 1000, - }, -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 3, - .max_speed_hz = 15 * 1000 * 1000, - } -#endif -}; - -static struct mtd_partition __initdata dk_nand_partition[] = { - { - .name = "NAND Partition 1", - .offset = 0, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition *nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(dk_nand_partition); - return dk_nand_partition; -} - -static struct at91_nand_data __initdata dk_nand_data = { - .ale = 22, - .cle = 21, - .det_pin = AT91_PIN_PB1, - .rdy_pin = AT91_PIN_PC2, - // .enable_pin = ... not there - .partition_info = nand_partitions, -}; - -#define DK_FLASH_BASE AT91_CHIPSELECT_0 -#define DK_FLASH_SIZE 0x200000 - -static struct physmap_flash_data dk_flash_data = { - .width = 2, -}; - -static struct resource dk_flash_resource = { - .start = DK_FLASH_BASE, - .end = DK_FLASH_BASE + DK_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device dk_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &dk_flash_data, - }, - .resource = &dk_flash_resource, - .num_resources = 1, -}; - - -static void __init dk_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&dk_eth_data); - /* USB Host */ - at91_add_device_usbh(&dk_usbh_data); - /* USB Device */ - at91_add_device_udc(&dk_udc_data); - at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ - /* Compact Flash */ - at91_add_device_cf(&dk_cf_data); - /* I2C */ - at91_add_device_i2c(); - /* SPI */ - at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices)); -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - /* DataFlash card */ - at91_set_gpio_output(AT91_PIN_PB7, 0); -#else - /* MMC */ - at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(&dk_mmc_data); -#endif - /* NAND */ - at91_add_device_nand(&dk_nand_data); - /* NOR Flash */ - platform_device_register(&dk_flash); - /* VGA */ -// dk_add_device_video(); -} - -MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK") - /* Maintainer: SAN People/Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = dk_map_io, - .init_irq = dk_init_irq, - .init_machine = dk_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-eb9200.c b/arch/arm/mach-at91rm9200/board-eb9200.c deleted file mode 100644 index 80b72cf7264c..000000000000 --- a/arch/arm/mach-at91rm9200/board-eb9200.c +++ /dev/null @@ -1,123 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-eb9200.c - * - * Copyright (C) 2005 SAN People, adapted for ATEB9200 from Embest - * by Andrew Patrikalakis - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata eb9200_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init eb9200_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_BGA); - - /* Setup the serial ports and console */ - at91_init_serial(&eb9200_uart_config); -} - -static void __init eb9200_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata eb9200_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata eb9200_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata eb9200_udc_data = { - .vbus_pin = AT91_PIN_PD4, - .pullup_pin = AT91_PIN_PD5, -}; - -static struct at91_cf_data __initdata eb9200_cf_data = { - .det_pin = AT91_PIN_PB0, - .rst_pin = AT91_PIN_PC5, - // .irq_pin = ... not connected - // .vcc_pin = ... always powered -}; - -static struct at91_mmc_data __initdata eb9200_mmc_data = { - .slot_b = 0, - .wire4 = 1, -}; - -static void __init eb9200_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&eb9200_eth_data); - /* USB Host */ - at91_add_device_usbh(&eb9200_usbh_data); - /* USB Device */ - at91_add_device_udc(&eb9200_udc_data); - /* I2C */ - at91_add_device_i2c(); - /* Compact Flash */ - at91_add_device_cf(&eb9200_cf_data); - /* SPI */ - at91_add_device_spi(NULL, 0); - /* MMC */ - /* only supports 1 or 4 bit interface, not wired through to SPI */ - at91_add_device_mmc(&eb9200_mmc_data); -} - -MACHINE_START(ATEB9200, "Embest ATEB9200") - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = eb9200_map_io, - .init_irq = eb9200_init_irq, - .init_machine = eb9200_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-ek.c b/arch/arm/mach-at91rm9200/board-ek.c deleted file mode 100644 index c4fdb415f20e..000000000000 --- a/arch/arm/mach-at91rm9200/board-ek.c +++ /dev/null @@ -1,174 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-ek.c - * - * Copyright (C) 2005 SAN People - * - * Epson S1D framebuffer glue code is: - * Copyright (C) 2005 Thibaut VARENE - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata ek_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init ek_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_BGA); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); - - /* Setup the serial ports and console */ - at91_init_serial(&ek_uart_config); -} - -static void __init ek_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata ek_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PD4, - .pullup_pin = AT91_PIN_PD5, -}; - -static struct at91_mmc_data __initdata ek_mmc_data = { - .det_pin = AT91_PIN_PB27, - .slot_b = 0, - .wire4 = 1, - .wp_pin = AT91_PIN_PA17, -}; - -static struct spi_board_info ek_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - }, -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 3, - .max_speed_hz = 15 * 1000 * 1000, - }, -#endif -}; - -#define EK_FLASH_BASE AT91_CHIPSELECT_0 -#define EK_FLASH_SIZE 0x200000 - -static struct physmap_flash_data ek_flash_data = { - .width = 2, -}; - -static struct resource ek_flash_resource = { - .start = EK_FLASH_BASE, - .end = EK_FLASH_BASE + EK_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device ek_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &ek_flash_data, - }, - .resource = &ek_flash_resource, - .num_resources = 1, -}; - - -static void __init ek_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&ek_eth_data); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ - /* I2C */ - at91_add_device_i2c(); - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - /* DataFlash card */ - at91_set_gpio_output(AT91_PIN_PB22, 0); -#else - /* MMC */ - at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(&ek_mmc_data); -#endif - /* NOR Flash */ - platform_device_register(&ek_flash); - /* VGA */ -// ek_add_device_video(); -} - -MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") - /* Maintainer: SAN People/Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, - .init_machine = ek_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-kafa.c b/arch/arm/mach-at91rm9200/board-kafa.c deleted file mode 100644 index 6ef3c4879829..000000000000 --- a/arch/arm/mach-at91rm9200/board-kafa.c +++ /dev/null @@ -1,109 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-kafa.c - * - * Copyright (C) 2006 Sperry-Sun - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata kafa_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init kafa_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_PQFP); - - /* Set up the LEDs */ - at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4); - - /* Setup the serial ports and console */ - at91_init_serial(&kafa_uart_config); -} - -static void __init kafa_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata kafa_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata kafa_usbh_data = { - .ports = 1, -}; - -static struct at91_udc_data __initdata kafa_udc_data = { - .vbus_pin = AT91_PIN_PB6, - .pullup_pin = AT91_PIN_PB7, -}; - -static void __init kafa_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&kafa_eth_data); - /* USB Host */ - at91_add_device_usbh(&kafa_usbh_data); - /* USB Device */ - at91_add_device_udc(&kafa_udc_data); - /* I2C */ - at91_add_device_i2c(); - /* SPI */ - at91_add_device_spi(NULL, 0); -} - -MACHINE_START(KAFA, "Sperry-Sun KAFA") - /* Maintainer: Sergei Sharonov */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = kafa_map_io, - .init_irq = kafa_init_irq, - .init_machine = kafa_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-kb9202.c b/arch/arm/mach-at91rm9200/board-kb9202.c deleted file mode 100644 index 759d8191854f..000000000000 --- a/arch/arm/mach-at91rm9200/board-kb9202.c +++ /dev/null @@ -1,143 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-kb9202.c - * - * Copyright (c) 2005 kb_admin - * KwikByte, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata kb9202_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 4, 0, 1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init kb9202_map_io(void) -{ - /* Initialize processor: 10 MHz crystal */ - at91rm9200_initialize(10000000, AT91RM9200_PQFP); - - /* Set up the LEDs */ - at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); - - /* Setup the serial ports and console */ - at91_init_serial(&kb9202_uart_config); -} - -static void __init kb9202_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata kb9202_eth_data = { - .phy_irq_pin = AT91_PIN_PB29, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata kb9202_usbh_data = { - .ports = 1, -}; - -static struct at91_udc_data __initdata kb9202_udc_data = { - .vbus_pin = AT91_PIN_PB24, - .pullup_pin = AT91_PIN_PB22, -}; - -static struct at91_mmc_data __initdata kb9202_mmc_data = { - .det_pin = AT91_PIN_PB2, - .slot_b = 0, - .wire4 = 1, -}; - -static struct mtd_partition __initdata kb9202_nand_partition[] = { - { - .name = "nand_fs", - .offset = 0, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition *nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(kb9202_nand_partition); - return kb9202_nand_partition; -} - -static struct at91_nand_data __initdata kb9202_nand_data = { - .ale = 22, - .cle = 21, - // .det_pin = ... not there - .rdy_pin = AT91_PIN_PC29, - .enable_pin = AT91_PIN_PC28, - .partition_info = nand_partitions, -}; - -static void __init kb9202_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&kb9202_eth_data); - /* USB Host */ - at91_add_device_usbh(&kb9202_usbh_data); - /* USB Device */ - at91_add_device_udc(&kb9202_udc_data); - /* MMC */ - at91_add_device_mmc(&kb9202_mmc_data); - /* I2C */ - at91_add_device_i2c(); - /* SPI */ - at91_add_device_spi(NULL, 0); - /* NAND */ - at91_add_device_nand(&kb9202_nand_data); -} - -MACHINE_START(KB9200, "KB920x") - /* Maintainer: KwikByte, Inc. */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = kb9202_map_io, - .init_irq = kb9202_init_irq, - .init_machine = kb9202_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-sam9260ek.c b/arch/arm/mach-at91rm9200/board-sam9260ek.c deleted file mode 100644 index 37c7a7d195c3..000000000000 --- a/arch/arm/mach-at91rm9200/board-sam9260ek.c +++ /dev/null @@ -1,202 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-ek.c - * - * Copyright (C) 2005 SAN People - * Copyright (C) 2006 Atmel - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 5 = USART0 .. USART5 - * 6 = DBGU - */ -static struct at91_uart_config __initdata ek_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 6, 0, 1, -1, -1, -1, -1 } /* ttyS0, ..., ttyS6 */ -}; - -static void __init ek_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* Setup the serial ports and console */ - at91_init_serial(&ek_uart_config); -} - -static void __init ek_init_irq(void) -{ - at91sam9260_init_interrupts(NULL); -} - - -/* - * USB Host port - */ -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, -}; - -/* - * USB Device port - */ -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - - -/* - * SPI devices. - */ -static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 1, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#endif -#endif -#if defined(CONFIG_SND_AT73C213) - { /* AT73C213 DAC */ - .modalias = "snd_at73c213", - .chip_select = 0, - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 1, - }, -#endif -}; - - -/* - * MACB Ethernet device - */ -static struct __initdata at91_eth_data ek_macb_data = { - .phy_irq_pin = AT91_PIN_PA7, - .is_rmii = 1, -}; - - -/* - * NAND flash - */ -static struct mtd_partition __initdata ek_nand_partition[] = { - { - .name = "Partition 1", - .offset = 0, - .size = 256 * 1024, - }, - { - .name = "Partition 2", - .offset = 256 * 1024, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition *nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(ek_nand_partition); - return ek_nand_partition; -} - -static struct at91_nand_data __initdata ek_nand_data = { - .ale = 21, - .cle = 22, -// .det_pin = ... not connected - .rdy_pin = AT91_PIN_PC13, - .enable_pin = AT91_PIN_PC14, - .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif -}; - - -/* - * MCI (SD/MMC) - */ -static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, - .wire4 = 1, -// .det_pin = ... not connected -// .wp_pin = ... not connected -// .vcc_pin = ... not connected -}; - -static void __init ek_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); - /* NAND */ - at91_add_device_nand(&ek_nand_data); - /* Ethernet */ - at91_add_device_eth(&ek_macb_data); - /* MMC */ - at91_add_device_mmc(&ek_mmc_data); -} - -MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") - /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, - .init_machine = ek_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/board-sam9261ek.c b/arch/arm/mach-at91rm9200/board-sam9261ek.c deleted file mode 100644 index 30b490d8886b..000000000000 --- a/arch/arm/mach-at91rm9200/board-sam9261ek.c +++ /dev/null @@ -1,259 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-ek.c - * - * Copyright (C) 2005 SAN People - * Copyright (C) 2006 Atmel - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "generic.h" - - -/* - * Serial port configuration. - * 0 .. 2 = USART0 .. USART2 - * 3 = DBGU - */ -static struct at91_uart_config __initdata ek_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 1, - .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */ -}; - -static void __init ek_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9261_initialize(18432000); - - /* Setup the serial ports and console */ - at91_init_serial(&ek_uart_config); -} - -static void __init ek_init_irq(void) -{ - at91sam9261_init_interrupts(NULL); -} - - -/* - * DM9000 ethernet device - */ -#if defined(CONFIG_DM9000) -static struct resource at91sam9261_dm9000_resource[] = { - [0] = { - .start = AT91_CHIPSELECT_2, - .end = AT91_CHIPSELECT_2 + 3, - .flags = IORESOURCE_MEM - }, - [1] = { - .start = AT91_CHIPSELECT_2 + 0x44, - .end = AT91_CHIPSELECT_2 + 0xFF, - .flags = IORESOURCE_MEM - }, - [2] = { - .start = AT91_PIN_PC11, - .end = AT91_PIN_PC11, - .flags = IORESOURCE_IRQ - } -}; - -static struct dm9000_plat_data dm9000_platdata = { - .flags = DM9000_PLATF_16BITONLY, -}; - -static struct platform_device at91sam9261_dm9000_device = { - .name = "dm9000", - .id = 0, - .num_resources = ARRAY_SIZE(at91sam9261_dm9000_resource), - .resource = at91sam9261_dm9000_resource, - .dev = { - .platform_data = &dm9000_platdata, - } -}; - -static void __init ek_add_device_dm9000(void) -{ - /* - * Configure Chip-Select 2 on SMC for the DM9000. - * Note: These timings were calculated for MASTER_CLOCK = 100000000 - * according to the DM9000 timings. - */ - at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8)); - at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16)); - at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1)); - - /* Configure Reset signal as output */ - at91_set_gpio_output(AT91_PIN_PC10, 0); - - /* Configure Interrupt pin as input, no pull-up */ - at91_set_gpio_input(AT91_PIN_PC11, 0); - - platform_device_register(&at91sam9261_dm9000_device); -} -#else -static void __init ek_add_device_dm9000(void) {} -#endif /* CONFIG_DM9000 */ - - -/* - * USB Host Port - */ -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, -}; - - -/* - * USB Device Port - */ -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PB29, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - - -/* - * MCI (SD/MMC) - */ -static struct at91_mmc_data __initdata ek_mmc_data = { - .wire4 = 1, -// .det_pin = ... not connected -// .wp_pin = ... not connected -// .vcc_pin = ... not connected -}; - - -/* - * NAND flash - */ -static struct mtd_partition __initdata ek_nand_partition[] = { - { - .name = "Partition 1", - .offset = 0, - .size = 256 * 1024, - }, - { - .name = "Partition 2", - .offset = 256 * 1024 , - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition *nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(ek_nand_partition); - return ek_nand_partition; -} - -static struct at91_nand_data __initdata ek_nand_data = { - .ale = 22, - .cle = 21, -// .det_pin = ... not connected - .rdy_pin = AT91_PIN_PC15, - .enable_pin = AT91_PIN_PC14, - .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif -}; - -/* - * SPI devices - */ -static struct spi_board_info ek_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) - { /* DataFlash card - jumper (J12) configurable to CS3 or CS0 */ - .modalias = "mtd_dataflash", - .chip_select = 3, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#elif defined(CONFIG_SND_AT73C213) - { /* AT73C213 DAC */ - .modalias = "snd_at73c213", - .chip_select = 3, - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 0, - }, -#endif -}; - - -static void __init ek_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - /* I2C */ - at91_add_device_i2c(); - /* NAND */ - at91_add_device_nand(&ek_nand_data); - /* DM9000 ethernet */ - ek_add_device_dm9000(); - - /* spi0 and mmc/sd share the same PIO pins */ -#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -#else - /* MMC */ - at91_add_device_mmc(&ek_mmc_data); -#endif -} - -MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK") - /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, - .init_machine = ek_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91rm9200/clock.c b/arch/arm/mach-at91rm9200/clock.c deleted file mode 100644 index 4dee21fefe5a..000000000000 --- a/arch/arm/mach-at91rm9200/clock.c +++ /dev/null @@ -1,644 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/clock.c - * - * Copyright (C) 2005 David Brownell - * Copyright (C) 2005 Ivan Kokshaysky - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "clock.h" - - -/* - * There's a lot more which can be done with clocks, including cpufreq - * integration, slow clock mode support (for system suspend), letting - * PLLB be used at other rates (on boards that don't need USB), etc. - */ - -#define clk_is_primary(x) ((x)->type & CLK_TYPE_PRIMARY) -#define clk_is_programmable(x) ((x)->type & CLK_TYPE_PROGRAMMABLE) -#define clk_is_peripheral(x) ((x)->type & CLK_TYPE_PERIPHERAL) -#define clk_is_sys(x) ((x)->type & CLK_TYPE_SYSTEM) - - -static LIST_HEAD(clocks); -static DEFINE_SPINLOCK(clk_lock); - -static u32 at91_pllb_usb_init; - -/* - * Four primary clock sources: two crystal oscillators (32K, main), and - * two PLLs. PLLA usually runs the master clock; and PLLB must run at - * 48 MHz (unless no USB function clocks are needed). The main clock and - * both PLLs are turned off to run in "slow clock mode" (system suspend). - */ -static struct clk clk32k = { - .name = "clk32k", - .rate_hz = AT91_SLOW_CLOCK, - .users = 1, /* always on */ - .id = 0, - .type = CLK_TYPE_PRIMARY, -}; -static struct clk main_clk = { - .name = "main", - .pmc_mask = AT91_PMC_MOSCS, /* in PMC_SR */ - .id = 1, - .type = CLK_TYPE_PRIMARY, -}; -static struct clk plla = { - .name = "plla", - .parent = &main_clk, - .pmc_mask = AT91_PMC_LOCKA, /* in PMC_SR */ - .id = 2, - .type = CLK_TYPE_PRIMARY | CLK_TYPE_PLL, -}; - -static void pllb_mode(struct clk *clk, int is_on) -{ - u32 value; - - if (is_on) { - is_on = AT91_PMC_LOCKB; - value = at91_pllb_usb_init; - } else - value = 0; - - // REVISIT: Add work-around for AT91RM9200 Errata #26 ? - at91_sys_write(AT91_CKGR_PLLBR, value); - - do { - cpu_relax(); - } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on); -} - -static struct clk pllb = { - .name = "pllb", - .parent = &main_clk, - .pmc_mask = AT91_PMC_LOCKB, /* in PMC_SR */ - .mode = pllb_mode, - .id = 3, - .type = CLK_TYPE_PRIMARY | CLK_TYPE_PLL, -}; - -static void pmc_sys_mode(struct clk *clk, int is_on) -{ - if (is_on) - at91_sys_write(AT91_PMC_SCER, clk->pmc_mask); - else - at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask); -} - -/* USB function clocks (PLLB must be 48 MHz) */ -static struct clk udpck = { - .name = "udpck", - .parent = &pllb, - .mode = pmc_sys_mode, -}; -static struct clk uhpck = { - .name = "uhpck", - .parent = &pllb, - .mode = pmc_sys_mode, -}; - - -/* - * The master clock is divided from the CPU clock (by 1-4). It's used for - * memory, interfaces to on-chip peripherals, the AIC, and sometimes more - * (e.g baud rate generation). It's sourced from one of the primary clocks. - */ -static struct clk mck = { - .name = "mck", - .pmc_mask = AT91_PMC_MCKRDY, /* in PMC_SR */ -}; - -static void pmc_periph_mode(struct clk *clk, int is_on) -{ - if (is_on) - at91_sys_write(AT91_PMC_PCER, clk->pmc_mask); - else - at91_sys_write(AT91_PMC_PCDR, clk->pmc_mask); -} - -static struct clk __init *at91_css_to_clk(unsigned long css) -{ - switch (css) { - case AT91_PMC_CSS_SLOW: - return &clk32k; - case AT91_PMC_CSS_MAIN: - return &main_clk; - case AT91_PMC_CSS_PLLA: - return &plla; - case AT91_PMC_CSS_PLLB: - return &pllb; - } - - return NULL; -} - -/* - * Associate a particular clock with a function (eg, "uart") and device. - * The drivers can then request the same 'function' with several different - * devices and not care about which clock name to use. - */ -void __init at91_clock_associate(const char *id, struct device *dev, const char *func) -{ - struct clk *clk = clk_get(NULL, id); - - if (!dev || !clk || !IS_ERR(clk_get(dev, func))) - return; - - clk->function = func; - clk->dev = dev; -} - -/* clocks cannot be de-registered no refcounting necessary */ -struct clk *clk_get(struct device *dev, const char *id) -{ - struct clk *clk; - - list_for_each_entry(clk, &clocks, node) { - if (strcmp(id, clk->name) == 0) - return clk; - if (clk->function && (dev == clk->dev) && strcmp(id, clk->function) == 0) - return clk; - } - - return ERR_PTR(-ENOENT); -} -EXPORT_SYMBOL(clk_get); - -void clk_put(struct clk *clk) -{ -} -EXPORT_SYMBOL(clk_put); - -static void __clk_enable(struct clk *clk) -{ - if (clk->parent) - __clk_enable(clk->parent); - if (clk->users++ == 0 && clk->mode) - clk->mode(clk, 1); -} - -int clk_enable(struct clk *clk) -{ - unsigned long flags; - - spin_lock_irqsave(&clk_lock, flags); - __clk_enable(clk); - spin_unlock_irqrestore(&clk_lock, flags); - return 0; -} -EXPORT_SYMBOL(clk_enable); - -static void __clk_disable(struct clk *clk) -{ - BUG_ON(clk->users == 0); - if (--clk->users == 0 && clk->mode) - clk->mode(clk, 0); - if (clk->parent) - __clk_disable(clk->parent); -} - -void clk_disable(struct clk *clk) -{ - unsigned long flags; - - spin_lock_irqsave(&clk_lock, flags); - __clk_disable(clk); - spin_unlock_irqrestore(&clk_lock, flags); -} -EXPORT_SYMBOL(clk_disable); - -unsigned long clk_get_rate(struct clk *clk) -{ - unsigned long flags; - unsigned long rate; - - spin_lock_irqsave(&clk_lock, flags); - for (;;) { - rate = clk->rate_hz; - if (rate || !clk->parent) - break; - clk = clk->parent; - } - spin_unlock_irqrestore(&clk_lock, flags); - return rate; -} -EXPORT_SYMBOL(clk_get_rate); - -/*------------------------------------------------------------------------*/ - -#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS - -/* - * For now, only the programmable clocks support reparenting (MCK could - * do this too, with care) or rate changing (the PLLs could do this too, - * ditto MCK but that's more for cpufreq). Drivers may reparent to get - * a better rate match; we don't. - */ - -long clk_round_rate(struct clk *clk, unsigned long rate) -{ - unsigned long flags; - unsigned prescale; - unsigned long actual; - - if (!clk_is_programmable(clk)) - return -EINVAL; - spin_lock_irqsave(&clk_lock, flags); - - actual = clk->parent->rate_hz; - for (prescale = 0; prescale < 7; prescale++) { - if (actual && actual <= rate) - break; - actual >>= 1; - } - - spin_unlock_irqrestore(&clk_lock, flags); - return (prescale < 7) ? actual : -ENOENT; -} -EXPORT_SYMBOL(clk_round_rate); - -int clk_set_rate(struct clk *clk, unsigned long rate) -{ - unsigned long flags; - unsigned prescale; - unsigned long actual; - - if (!clk_is_programmable(clk)) - return -EINVAL; - if (clk->users) - return -EBUSY; - spin_lock_irqsave(&clk_lock, flags); - - actual = clk->parent->rate_hz; - for (prescale = 0; prescale < 7; prescale++) { - if (actual && actual <= rate) { - u32 pckr; - - pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); - pckr &= AT91_PMC_CSS_PLLB; /* clock selection */ - pckr |= prescale << 2; - at91_sys_write(AT91_PMC_PCKR(clk->id), pckr); - clk->rate_hz = actual; - break; - } - actual >>= 1; - } - - spin_unlock_irqrestore(&clk_lock, flags); - return (prescale < 7) ? actual : -ENOENT; -} -EXPORT_SYMBOL(clk_set_rate); - -struct clk *clk_get_parent(struct clk *clk) -{ - return clk->parent; -} -EXPORT_SYMBOL(clk_get_parent); - -int clk_set_parent(struct clk *clk, struct clk *parent) -{ - unsigned long flags; - - if (clk->users) - return -EBUSY; - if (!clk_is_primary(parent) || !clk_is_programmable(clk)) - return -EINVAL; - spin_lock_irqsave(&clk_lock, flags); - - clk->rate_hz = parent->rate_hz; - clk->parent = parent; - at91_sys_write(AT91_PMC_PCKR(clk->id), parent->id); - - spin_unlock_irqrestore(&clk_lock, flags); - return 0; -} -EXPORT_SYMBOL(clk_set_parent); - -/* establish PCK0..PCK3 parentage and rate */ -static void init_programmable_clock(struct clk *clk) -{ - struct clk *parent; - u32 pckr; - - pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); - parent = at91_css_to_clk(pckr & AT91_PMC_CSS); - clk->parent = parent; - clk->rate_hz = parent->rate_hz / (1 << ((pckr >> 2) & 3)); -} - -#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ - -/*------------------------------------------------------------------------*/ - -#ifdef CONFIG_DEBUG_FS - -static int at91_clk_show(struct seq_file *s, void *unused) -{ - u32 scsr, pcsr, sr; - struct clk *clk; - unsigned i; - - seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR)); - seq_printf(s, "PCSR = %8x\n", pcsr = at91_sys_read(AT91_PMC_PCSR)); - - seq_printf(s, "MOR = %8x\n", at91_sys_read(AT91_CKGR_MOR)); - seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR)); - seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR)); - seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); - - seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR)); - for (i = 0; i < 4; i++) - seq_printf(s, "PCK%d = %8x\n", i, at91_sys_read(AT91_PMC_PCKR(i))); - seq_printf(s, "SR = %8x\n", sr = at91_sys_read(AT91_PMC_SR)); - - seq_printf(s, "\n"); - - list_for_each_entry(clk, &clocks, node) { - char *state; - - if (clk->mode == pmc_sys_mode) - state = (scsr & clk->pmc_mask) ? "on" : "off"; - else if (clk->mode == pmc_periph_mode) - state = (pcsr & clk->pmc_mask) ? "on" : "off"; - else if (clk->pmc_mask) - state = (sr & clk->pmc_mask) ? "on" : "off"; - else if (clk == &clk32k || clk == &main_clk) - state = "on"; - else - state = ""; - - seq_printf(s, "%-10s users=%2d %-3s %9ld Hz %s\n", - clk->name, clk->users, state, clk_get_rate(clk), - clk->parent ? clk->parent->name : ""); - } - return 0; -} - -static int at91_clk_open(struct inode *inode, struct file *file) -{ - return single_open(file, at91_clk_show, NULL); -} - -static struct file_operations at91_clk_operations = { - .open = at91_clk_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - -static int __init at91_clk_debugfs_init(void) -{ - /* /sys/kernel/debug/at91_clk */ - (void) debugfs_create_file("at91_clk", S_IFREG | S_IRUGO, NULL, NULL, &at91_clk_operations); - - return 0; -} -postcore_initcall(at91_clk_debugfs_init); - -#endif - -/*------------------------------------------------------------------------*/ - -/* Register a new clock */ -int __init clk_register(struct clk *clk) -{ - if (clk_is_peripheral(clk)) { - clk->parent = &mck; - clk->mode = pmc_periph_mode; - list_add_tail(&clk->node, &clocks); - } - else if (clk_is_sys(clk)) { - clk->parent = &mck; - clk->mode = pmc_sys_mode; - - list_add_tail(&clk->node, &clocks); - } -#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS - else if (clk_is_programmable(clk)) { - clk->mode = pmc_sys_mode; - init_programmable_clock(clk); - list_add_tail(&clk->node, &clocks); - } -#endif - - return 0; -} - - -/*------------------------------------------------------------------------*/ - -static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg) -{ - unsigned mul, div; - - div = reg & 0xff; - mul = (reg >> 16) & 0x7ff; - if (div && mul) { - freq /= div; - freq *= mul + 1; - } else - freq = 0; - - return freq; -} - -static u32 __init at91_usb_rate(struct clk *pll, u32 freq, u32 reg) -{ - if (pll == &pllb && (reg & AT91_PMC_USB96M)) - return freq / 2; - else - return freq; -} - -static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq) -{ - unsigned i, div = 0, mul = 0, diff = 1 << 30; - unsigned ret = (out_freq > 155000000) ? 0xbe00 : 0x3e00; - - /* PLL output max 240 MHz (or 180 MHz per errata) */ - if (out_freq > 240000000) - goto fail; - - for (i = 1; i < 256; i++) { - int diff1; - unsigned input, mul1; - - /* - * PLL input between 1MHz and 32MHz per spec, but lower - * frequences seem necessary in some cases so allow 100K. - */ - input = main_freq / i; - if (input < 100000) - continue; - if (input > 32000000) - continue; - - mul1 = out_freq / input; - if (mul1 > 2048) - continue; - if (mul1 < 2) - goto fail; - - diff1 = out_freq - input * mul1; - if (diff1 < 0) - diff1 = -diff1; - if (diff > diff1) { - diff = diff1; - div = i; - mul = mul1; - if (diff == 0) - break; - } - } - if (i == 256 && diff > (out_freq >> 5)) - goto fail; - return ret | ((mul - 1) << 16) | div; -fail: - return 0; -} - -/* - * Several unused clocks may be active. Turn them off. - */ -static void __init at91_periphclk_reset(void) -{ - unsigned long reg; - struct clk *clk; - - reg = at91_sys_read(AT91_PMC_PCSR); - - list_for_each_entry(clk, &clocks, node) { - if (clk->mode != pmc_periph_mode) - continue; - - if (clk->users > 0) - reg &= ~clk->pmc_mask; - } - - at91_sys_write(AT91_PMC_PCDR, reg); -} - -static struct clk *const standard_pmc_clocks[] __initdata = { - /* four primary clocks */ - &clk32k, - &main_clk, - &plla, - &pllb, - - /* PLLB children (USB) */ - &udpck, - &uhpck, - - /* MCK */ - &mck -}; - -int __init at91_clock_init(unsigned long main_clock) -{ - unsigned tmp, freq, mckr; - int i; - - /* - * When the bootloader initialized the main oscillator correctly, - * there's no problem using the cycle counter. But if it didn't, - * or when using oscillator bypass mode, we must be told the speed - * of the main clock. - */ - if (!main_clock) { - do { - tmp = at91_sys_read(AT91_CKGR_MCFR); - } while (!(tmp & AT91_PMC_MAINRDY)); - main_clock = (tmp & AT91_PMC_MAINF) * (AT91_SLOW_CLOCK / 16); - } - main_clk.rate_hz = main_clock; - - /* report if PLLA is more than mildly overclocked */ - plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR)); - if (plla.rate_hz > 209000000) - pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); - - /* - * USB clock init: choose 48 MHz PLLB value, turn all clocks off, - * disable 48MHz clock during usb peripheral suspend. - * - * REVISIT: assumes MCK doesn't derive from PLLB! - */ - at91_pllb_usb_init = at91_pll_calc(main_clock, 48000000 * 2) | AT91_PMC_USB96M; - pllb.rate_hz = at91_pll_rate(&pllb, main_clock, at91_pllb_usb_init); - if (cpu_is_at91rm9200()) { - uhpck.pmc_mask = AT91RM9200_PMC_UHP; - udpck.pmc_mask = AT91RM9200_PMC_UDP; - at91_sys_write(AT91_PMC_SCDR, AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP); - at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); - } else if (cpu_is_at91sam9260()) { - uhpck.pmc_mask = AT91SAM926x_PMC_UHP; - udpck.pmc_mask = AT91SAM926x_PMC_UDP; - at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP); - } else if (cpu_is_at91sam9261()) { - uhpck.pmc_mask = (AT91SAM926x_PMC_UHP | AT91_PMC_HCK0); - udpck.pmc_mask = AT91SAM926x_PMC_UDP; - at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91_PMC_HCK0 | AT91SAM926x_PMC_UDP); - } - at91_sys_write(AT91_CKGR_PLLBR, 0); - - udpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init); - uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init); - - /* - * MCK and CPU derive from one of those primary clocks. - * For now, assume this parentage won't change. - */ - mckr = at91_sys_read(AT91_PMC_MCKR); - mck.parent = at91_css_to_clk(mckr & AT91_PMC_CSS); - freq = mck.parent->rate_hz; - freq /= (1 << ((mckr >> 2) & 3)); /* prescale */ - mck.rate_hz = freq / (1 + ((mckr >> 8) & 3)); /* mdiv */ - - /* Register the PMC's standard clocks */ - for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) - list_add_tail(&standard_pmc_clocks[i]->node, &clocks); - - /* MCK and CPU clock are "always on" */ - clk_enable(&mck); - - printk("Clocks: CPU %u MHz, master %u MHz, main %u.%03u MHz\n", - freq / 1000000, (unsigned) mck.rate_hz / 1000000, - (unsigned) main_clock / 1000000, - ((unsigned) main_clock % 1000000) / 1000); - - /* disable all programmable clocks */ - at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK0 | AT91_PMC_PCK1 | AT91_PMC_PCK2 | AT91_PMC_PCK3); - - /* disable all other unused peripheral clocks */ - at91_periphclk_reset(); - - return 0; -} diff --git a/arch/arm/mach-at91rm9200/clock.h b/arch/arm/mach-at91rm9200/clock.h deleted file mode 100644 index b5c7a2eb2d1d..000000000000 --- a/arch/arm/mach-at91rm9200/clock.h +++ /dev/null @@ -1,31 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/clock.h - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#define CLK_TYPE_PRIMARY 0x1 -#define CLK_TYPE_PLL 0x2 -#define CLK_TYPE_PROGRAMMABLE 0x4 -#define CLK_TYPE_PERIPHERAL 0x8 -#define CLK_TYPE_SYSTEM 0x10 - - -struct clk { - struct list_head node; - const char *name; /* unique clock name */ - const char *function; /* function of the clock */ - struct device *dev; /* device associated with function */ - unsigned long rate_hz; - struct clk *parent; - u32 pmc_mask; - void (*mode)(struct clk *, int); - unsigned id:2; /* PCK0..3, or 32k/main/a/b */ - unsigned type; /* clock type */ - u16 users; -}; - - -extern int __init clk_register(struct clk *clk); diff --git a/arch/arm/mach-at91rm9200/generic.h b/arch/arm/mach-at91rm9200/generic.h deleted file mode 100644 index 8c4d5a77d485..000000000000 --- a/arch/arm/mach-at91rm9200/generic.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/generic.h - * - * Copyright (C) 2005 David Brownell - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - - /* Processors */ -extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks); -extern void __init at91sam9260_initialize(unsigned long main_clock); -extern void __init at91sam9261_initialize(unsigned long main_clock); - - /* Interrupts */ -extern void __init at91rm9200_init_interrupts(unsigned int priority[]); -extern void __init at91sam9260_init_interrupts(unsigned int priority[]); -extern void __init at91sam9261_init_interrupts(unsigned int priority[]); -extern void __init at91_aic_init(unsigned int priority[]); - - /* Timer */ -struct sys_timer; -extern struct sys_timer at91rm9200_timer; -extern struct sys_timer at91sam926x_timer; - - /* Clocks */ -extern int __init at91_clock_init(unsigned long main_clock); -struct device; -extern void __init at91_clock_associate(const char *id, struct device *dev, const char *func); - - /* Power Management */ -extern void at91_irq_suspend(void); -extern void at91_irq_resume(void); - - /* GPIO */ -#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */ -#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */ - -struct at91_gpio_bank { - unsigned short id; /* peripheral ID */ - unsigned long offset; /* offset from system peripheral base */ - struct clk *clock; /* associated clock */ -}; -extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks); -extern void __init at91_gpio_irq_setup(void); - -extern void (*at91_arch_reset)(void); -extern int at91_extern_irq; diff --git a/arch/arm/mach-at91rm9200/gpio.c b/arch/arm/mach-at91rm9200/gpio.c deleted file mode 100644 index af22659c8a28..000000000000 --- a/arch/arm/mach-at91rm9200/gpio.c +++ /dev/null @@ -1,414 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/gpio.c - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include "generic.h" - - -static struct at91_gpio_bank *gpio; -static int gpio_banks; - - -static inline void __iomem *pin_to_controller(unsigned pin) -{ - void __iomem *sys_base = (void __iomem *) AT91_VA_BASE_SYS; - - pin -= PIN_BASE; - pin /= 32; - if (likely(pin < gpio_banks)) - return sys_base + gpio[pin].offset; - - return NULL; -} - -static inline unsigned pin_to_mask(unsigned pin) -{ - pin -= PIN_BASE; - return 1 << (pin % 32); -} - - -/*--------------------------------------------------------------------------*/ - -/* Not all hardware capabilities are exposed through these calls; they - * only encapsulate the most common features and modes. (So if you - * want to change signals in groups, do it directly.) - * - * Bootloaders will usually handle some of the pin multiplexing setup. - * The intent is certainly that by the time Linux is fully booted, all - * pins should have been fully initialized. These setup calls should - * only be used by board setup routines, or possibly in driver probe(). - * - * For bootloaders doing all that setup, these calls could be inlined - * as NOPs so Linux won't duplicate any setup code - */ - - -/* - * mux the pin to the "A" internal peripheral role. - */ -int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_ASR); - __raw_writel(mask, pio + PIO_PDR); - return 0; -} -EXPORT_SYMBOL(at91_set_A_periph); - - -/* - * mux the pin to the "B" internal peripheral role. - */ -int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_BSR); - __raw_writel(mask, pio + PIO_PDR); - return 0; -} -EXPORT_SYMBOL(at91_set_B_periph); - - -/* - * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and - * configure it for an input. - */ -int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_ODR); - __raw_writel(mask, pio + PIO_PER); - return 0; -} -EXPORT_SYMBOL(at91_set_gpio_input); - - -/* - * mux the pin to the gpio controller (instead of "A" or "B" peripheral), - * and configure it for an output. - */ -int __init_or_module at91_set_gpio_output(unsigned pin, int value) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + PIO_PUDR); - __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); - __raw_writel(mask, pio + PIO_OER); - __raw_writel(mask, pio + PIO_PER); - return 0; -} -EXPORT_SYMBOL(at91_set_gpio_output); - - -/* - * enable/disable the glitch filter; mostly used with IRQ handling. - */ -int __init_or_module at91_set_deglitch(unsigned pin, int is_on) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - __raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR)); - return 0; -} -EXPORT_SYMBOL(at91_set_deglitch); - -/* - * enable/disable the multi-driver; This is only valid for output and - * allows the output pin to run as an open collector output. - */ -int __init_or_module at91_set_multi_drive(unsigned pin, int is_on) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - - __raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR)); - return 0; -} -EXPORT_SYMBOL(at91_set_multi_drive); - -/*--------------------------------------------------------------------------*/ - -/* - * assuming the pin is muxed as a gpio output, set its value. - */ -int at91_set_gpio_value(unsigned pin, int value) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (!pio) - return -EINVAL; - __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); - return 0; -} -EXPORT_SYMBOL(at91_set_gpio_value); - - -/* - * read the pin's value (works even if it's not muxed as a gpio). - */ -int at91_get_gpio_value(unsigned pin) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - u32 pdsr; - - if (!pio) - return -EINVAL; - pdsr = __raw_readl(pio + PIO_PDSR); - return (pdsr & mask) != 0; -} -EXPORT_SYMBOL(at91_get_gpio_value); - -/*--------------------------------------------------------------------------*/ - -#ifdef CONFIG_PM - -static u32 wakeups[MAX_GPIO_BANKS]; -static u32 backups[MAX_GPIO_BANKS]; - -static int gpio_irq_set_wake(unsigned pin, unsigned state) -{ - unsigned mask = pin_to_mask(pin); - unsigned bank = (pin - PIN_BASE) / 32; - - if (unlikely(bank >= MAX_GPIO_BANKS)) - return -EINVAL; - - if (state) - wakeups[bank] |= mask; - else - wakeups[bank] &= ~mask; - - set_irq_wake(gpio[bank].id, state); - - return 0; -} - -void at91_gpio_suspend(void) -{ - int i; - - for (i = 0; i < gpio_banks; i++) { - u32 pio = gpio[i].offset; - - backups[i] = at91_sys_read(pio + PIO_IMR); - at91_sys_write(pio + PIO_IDR, backups[i]); - at91_sys_write(pio + PIO_IER, wakeups[i]); - - if (!wakeups[i]) - clk_disable(gpio[i].clock); - else { -#ifdef CONFIG_PM_DEBUG - printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]); -#endif - } - } -} - -void at91_gpio_resume(void) -{ - int i; - - for (i = 0; i < gpio_banks; i++) { - u32 pio = gpio[i].offset; - - if (!wakeups[i]) - clk_enable(gpio[i].clock); - - at91_sys_write(pio + PIO_IDR, wakeups[i]); - at91_sys_write(pio + PIO_IER, backups[i]); - } -} - -#else -#define gpio_irq_set_wake NULL -#endif - - -/* Several AIC controller irqs are dispatched through this GPIO handler. - * To use any AT91_PIN_* as an externally triggered IRQ, first call - * at91_set_gpio_input() then maybe enable its glitch filter. - * Then just request_irq() with the pin ID; it works like any ARM IRQ - * handler, though it always triggers on rising and falling edges. - * - * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after - * configuring them with at91_set_a_periph() or at91_set_b_periph(). - * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering. - */ - -static void gpio_irq_mask(unsigned pin) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (pio) - __raw_writel(mask, pio + PIO_IDR); -} - -static void gpio_irq_unmask(unsigned pin) -{ - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); - - if (pio) - __raw_writel(mask, pio + PIO_IER); -} - -static int gpio_irq_type(unsigned pin, unsigned type) -{ - return (type == IRQT_BOTHEDGE) ? 0 : -EINVAL; -} - -static struct irq_chip gpio_irqchip = { - .name = "GPIO", - .mask = gpio_irq_mask, - .unmask = gpio_irq_unmask, - .set_type = gpio_irq_type, - .set_wake = gpio_irq_set_wake, -}; - -static void gpio_irq_handler(unsigned irq, struct irq_desc *desc) -{ - unsigned pin; - struct irq_desc *gpio; - void __iomem *pio; - u32 isr; - - pio = get_irq_chip_data(irq); - - /* temporarily mask (level sensitive) parent IRQ */ - desc->chip->ack(irq); - for (;;) { - /* reading ISR acks the pending (edge triggered) GPIO interrupt */ - isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR); - if (!isr) - break; - - pin = (unsigned) get_irq_data(irq); - gpio = &irq_desc[pin]; - - while (isr) { - if (isr & 1) { - if (unlikely(gpio->depth)) { - /* - * The core ARM interrupt handler lazily disables IRQs so - * another IRQ must be generated before it actually gets - * here to be disabled on the GPIO controller. - */ - gpio_irq_mask(pin); - } - else - desc_handle_irq(pin, gpio); - } - pin++; - gpio++; - isr >>= 1; - } - } - desc->chip->unmask(irq); - /* now it may re-trigger */ -} - -/*--------------------------------------------------------------------------*/ - -/* - * Called from the processor-specific init to enable GPIO interrupt support. - */ -void __init at91_gpio_irq_setup(void) -{ - unsigned pioc, pin; - - for (pioc = 0, pin = PIN_BASE; - pioc < gpio_banks; - pioc++) { - void __iomem *controller; - unsigned id = gpio[pioc].id; - unsigned i; - - clk_enable(gpio[pioc].clock); /* enable PIO controller's clock */ - - controller = (void __iomem *) AT91_VA_BASE_SYS + gpio[pioc].offset; - __raw_writel(~0, controller + PIO_IDR); - - set_irq_data(id, (void *) pin); - set_irq_chip_data(id, controller); - - for (i = 0; i < 32; i++, pin++) { - /* - * Can use the "simple" and not "edge" handler since it's - * shorter, and the AIC handles interupts sanely. - */ - set_irq_chip(pin, &gpio_irqchip); - set_irq_handler(pin, handle_simple_irq); - set_irq_flags(pin, IRQF_VALID); - } - - set_irq_chained_handler(id, gpio_irq_handler); - } - pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks); -} - -/* - * Called from the processor-specific init to enable GPIO pin support. - */ -void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks) -{ - BUG_ON(nr_banks > MAX_GPIO_BANKS); - - gpio = data; - gpio_banks = nr_banks; -} diff --git a/arch/arm/mach-at91rm9200/irq.c b/arch/arm/mach-at91rm9200/irq.c deleted file mode 100644 index 2148daafd29c..000000000000 --- a/arch/arm/mach-at91rm9200/irq.c +++ /dev/null @@ -1,168 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/irq.c - * - * Copyright (C) 2004 SAN People - * Copyright (C) 2004 ATMEL - * Copyright (C) Rick Bronson - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - - -static void at91_aic_mask_irq(unsigned int irq) -{ - /* Disable interrupt on AIC */ - at91_sys_write(AT91_AIC_IDCR, 1 << irq); -} - -static void at91_aic_unmask_irq(unsigned int irq) -{ - /* Enable interrupt on AIC */ - at91_sys_write(AT91_AIC_IECR, 1 << irq); -} - -unsigned int at91_extern_irq; - -#define is_extern_irq(irq) ((1 << (irq)) & at91_extern_irq) - -static int at91_aic_set_type(unsigned irq, unsigned type) -{ - unsigned int smr, srctype; - - switch (type) { - case IRQT_HIGH: - srctype = AT91_AIC_SRCTYPE_HIGH; - break; - case IRQT_RISING: - srctype = AT91_AIC_SRCTYPE_RISING; - break; - case IRQT_LOW: - if ((irq == AT91_ID_FIQ) || is_extern_irq(irq)) /* only supported on external interrupts */ - srctype = AT91_AIC_SRCTYPE_LOW; - else - return -EINVAL; - break; - case IRQT_FALLING: - if ((irq == AT91_ID_FIQ) || is_extern_irq(irq)) /* only supported on external interrupts */ - srctype = AT91_AIC_SRCTYPE_FALLING; - else - return -EINVAL; - break; - default: - return -EINVAL; - } - - smr = at91_sys_read(AT91_AIC_SMR(irq)) & ~AT91_AIC_SRCTYPE; - at91_sys_write(AT91_AIC_SMR(irq), smr | srctype); - return 0; -} - -#ifdef CONFIG_PM - -static u32 wakeups; -static u32 backups; - -static int at91_aic_set_wake(unsigned irq, unsigned value) -{ - if (unlikely(irq >= 32)) - return -EINVAL; - - if (value) - wakeups |= (1 << irq); - else - wakeups &= ~(1 << irq); - - return 0; -} - -void at91_irq_suspend(void) -{ - backups = at91_sys_read(AT91_AIC_IMR); - at91_sys_write(AT91_AIC_IDCR, backups); - at91_sys_write(AT91_AIC_IECR, wakeups); -} - -void at91_irq_resume(void) -{ - at91_sys_write(AT91_AIC_IDCR, wakeups); - at91_sys_write(AT91_AIC_IECR, backups); -} - -#else -#define at91_aic_set_wake NULL -#endif - -static struct irq_chip at91_aic_chip = { - .name = "AIC", - .ack = at91_aic_mask_irq, - .mask = at91_aic_mask_irq, - .unmask = at91_aic_unmask_irq, - .set_type = at91_aic_set_type, - .set_wake = at91_aic_set_wake, -}; - -/* - * Initialize the AIC interrupt controller. - */ -void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS]) -{ - unsigned int i; - - /* - * The IVR is used by macro get_irqnr_and_base to read and verify. - * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred. - */ - for (i = 0; i < NR_AIC_IRQS; i++) { - /* Put irq number in Source Vector Register: */ - at91_sys_write(AT91_AIC_SVR(i), i); - /* Active Low interrupt, with the specified priority */ - at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]); - - set_irq_chip(i, &at91_aic_chip); - set_irq_handler(i, handle_level_irq); - set_irq_flags(i, IRQF_VALID | IRQF_PROBE); - - /* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */ - if (i < 8) - at91_sys_write(AT91_AIC_EOICR, 0); - } - - /* - * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS - * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU - */ - at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS); - - /* No debugging in AIC: Debug (Protect) Control Register */ - at91_sys_write(AT91_AIC_DCR, 0); - - /* Disable and clear all interrupts initially */ - at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF); - at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF); -} diff --git a/arch/arm/mach-at91rm9200/leds.c b/arch/arm/mach-at91rm9200/leds.c deleted file mode 100644 index 1a333730466e..000000000000 --- a/arch/arm/mach-at91rm9200/leds.c +++ /dev/null @@ -1,99 +0,0 @@ -/* - * LED driver for Atmel AT91-based boards. - * - * Copyright (C) SAN People (Pty) Ltd - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. -*/ - -#include -#include -#include - -#include -#include -#include -#include - - -static inline void at91_led_on(unsigned int led) -{ - at91_set_gpio_value(led, 0); -} - -static inline void at91_led_off(unsigned int led) -{ - at91_set_gpio_value(led, 1); -} - -static inline void at91_led_toggle(unsigned int led) -{ - unsigned long is_off = at91_get_gpio_value(led); - if (is_off) - at91_led_on(led); - else - at91_led_off(led); -} - - -/* - * Handle LED events. - */ -static void at91_leds_event(led_event_t evt) -{ - unsigned long flags; - - local_irq_save(flags); - - switch(evt) { - case led_start: /* System startup */ - at91_led_on(at91_leds_cpu); - break; - - case led_stop: /* System stop / suspend */ - at91_led_off(at91_leds_cpu); - break; - -#ifdef CONFIG_LEDS_TIMER - case led_timer: /* Every 50 timer ticks */ - at91_led_toggle(at91_leds_timer); - break; -#endif - -#ifdef CONFIG_LEDS_CPU - case led_idle_start: /* Entering idle state */ - at91_led_off(at91_leds_cpu); - break; - - case led_idle_end: /* Exit idle state */ - at91_led_on(at91_leds_cpu); - break; -#endif - - default: - break; - } - - local_irq_restore(flags); -} - - -static int __init leds_init(void) -{ - if (!at91_leds_timer || !at91_leds_cpu) - return -ENODEV; - - /* Enable PIO to access the LEDs */ - at91_set_gpio_output(at91_leds_timer, 1); - at91_set_gpio_output(at91_leds_cpu, 1); - - leds_event = at91_leds_event; - - leds_event(led_start); - return 0; -} - -__initcall(leds_init); diff --git a/arch/arm/mach-at91rm9200/pm.c b/arch/arm/mach-at91rm9200/pm.c deleted file mode 100644 index 67aa5572a3ea..000000000000 --- a/arch/arm/mach-at91rm9200/pm.c +++ /dev/null @@ -1,227 +0,0 @@ -/* - * arch/arm/mach-at91rm9200/pm.c - * AT91 Power Management - * - * Copyright (C) 2005 David Brownell - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include "generic.h" - - -static int at91_pm_valid_state(suspend_state_t state) -{ - switch (state) { - case PM_SUSPEND_ON: - case PM_SUSPEND_STANDBY: - case PM_SUSPEND_MEM: - return 1; - - default: - return 0; - } -} - - -static suspend_state_t target_state; - -/* - * Called after processes are frozen, but before we shutdown devices. - */ -static int at91_pm_prepare(suspend_state_t state) -{ - target_state = state; - return 0; -} - -/* - * Verify that all the clocks are correct before entering - * slow-clock mode. - */ -static int at91_pm_verify_clocks(void) -{ - unsigned long scsr; - int i; - - scsr = at91_sys_read(AT91_PMC_SCSR); - - /* USB must not be using PLLB */ - if (cpu_is_at91rm9200()) { - if ((scsr & (AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP)) != 0) { - pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); - return 0; - } - } else if (cpu_is_at91sam9260()) { -#warning "Check SAM9260 USB clocks" - } else if (cpu_is_at91sam9261()) { -#warning "Check SAM9261 USB clocks" - } - -#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS - /* PCK0..PCK3 must be disabled, or configured to use clk32k */ - for (i = 0; i < 4; i++) { - u32 css; - - if ((scsr & (AT91_PMC_PCK0 << i)) == 0) - continue; - - css = at91_sys_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS; - if (css != AT91_PMC_CSS_SLOW) { - pr_debug("AT91: PM - Suspend-to-RAM with PCK%d src %d\n", i, css); - return 0; - } - } -#endif - - return 1; -} - -/* - * Call this from platform driver suspend() to see how deeply to suspend. - * For example, some controllers (like OHCI) need one of the PLL clocks - * in order to act as a wakeup source, and those are not available when - * going into slow clock mode. - * - * REVISIT: generalize as clk_will_be_available(clk)? Other platforms have - * the very same problem (but not using at91 main_clk), and it'd be better - * to add one generic API rather than lots of platform-specific ones. - */ -int at91_suspend_entering_slow_clock(void) -{ - return (target_state == PM_SUSPEND_MEM); -} -EXPORT_SYMBOL(at91_suspend_entering_slow_clock); - - -static void (*slow_clock)(void); - - -static int at91_pm_enter(suspend_state_t state) -{ - at91_gpio_suspend(); - at91_irq_suspend(); - - pr_debug("AT91: PM - wake mask %08x, pm state %d\n", - /* remember all the always-wake irqs */ - (at91_sys_read(AT91_PMC_PCSR) - | (1 << AT91_ID_FIQ) - | (1 << AT91_ID_SYS) - | (at91_extern_irq)) - & at91_sys_read(AT91_AIC_IMR), - state); - - switch (state) { - /* - * Suspend-to-RAM is like STANDBY plus slow clock mode, so - * drivers must suspend more deeply: only the master clock - * controller may be using the main oscillator. - */ - case PM_SUSPEND_MEM: - /* - * Ensure that clocks are in a valid state. - */ - if (!at91_pm_verify_clocks()) - goto error; - - /* - * Enter slow clock mode by switching over to clk32k and - * turning off the main oscillator; reverse on wakeup. - */ - if (slow_clock) { - slow_clock(); - break; - } else { - /* DEVELOPMENT ONLY */ - pr_info("AT91: PM - no slow clock mode yet ...\n"); - /* FALLTHROUGH leaving master clock alone */ - } - - /* - * STANDBY mode has *all* drivers suspended; ignores irqs not - * marked as 'wakeup' event sources; and reduces DRAM power. - * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and - * nothing fancy done with main or cpu clocks. - */ - case PM_SUSPEND_STANDBY: - /* - * NOTE: the Wait-for-Interrupt instruction needs to be - * in icache so the SDRAM stays in self-refresh mode until - * the wakeup IRQ occurs. - */ - asm("b 1f; .align 5; 1:"); - asm("mcr p15, 0, r0, c7, c10, 4"); /* drain write buffer */ - at91_sys_write(AT91_SDRAMC_SRR, 1); /* self-refresh mode */ - /* fall though to next state */ - - case PM_SUSPEND_ON: - asm("mcr p15, 0, r0, c7, c0, 4"); /* wait for interrupt */ - break; - - default: - pr_debug("AT91: PM - bogus suspend state %d\n", state); - goto error; - } - - pr_debug("AT91: PM - wakeup %08x\n", - at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR)); - -error: - target_state = PM_SUSPEND_ON; - at91_irq_resume(); - at91_gpio_resume(); - return 0; -} - - -static struct pm_ops at91_pm_ops ={ - .pm_disk_mode = 0, - .valid = at91_pm_valid_state, - .prepare = at91_pm_prepare, - .enter = at91_pm_enter, -}; - -static int __init at91_pm_init(void) -{ - printk("AT91: Power Management\n"); - -#ifdef CONFIG_AT91_PM_SLOW_CLOCK - /* REVISIT allocations of SRAM should be dynamically managed. - * FIQ handlers and other components will want SRAM/TCM too... - */ - slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K)); - memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz); -#endif - - /* Disable SDRAM low-power mode. Cannot be used with self-refresh. */ - at91_sys_write(AT91_SDRAMC_LPR, 0); - - pm_set_ops(&at91_pm_ops); - - return 0; -} -arch_initcall(at91_pm_init); diff --git a/arch/avr32/mach-at32ap/clock.c b/arch/avr32/mach-at32ap/clock.c index 3d0d1097389f..ecbd4a21e432 100644 --- a/arch/avr32/mach-at32ap/clock.c +++ b/arch/avr32/mach-at32ap/clock.c @@ -3,7 +3,7 @@ * * Copyright (C) 2006 Atmel Corporation * - * Based on arch/arm/mach-at91rm9200/clock.c + * Based on arch/arm/mach-at91/clock.c * Copyright (C) 2005 David Brownell * Copyright (C) 2005 Ivan Kokshaysky * diff --git a/arch/avr32/mach-at32ap/clock.h b/arch/avr32/mach-at32ap/clock.h index f953f044ba4d..bb8e1f295835 100644 --- a/arch/avr32/mach-at32ap/clock.h +++ b/arch/avr32/mach-at32ap/clock.h @@ -3,7 +3,7 @@ * * Copyright (C) 2006 Atmel Corporation * - * Based on arch/arm/mach-at91rm9200/clock.c + * Based on arch/arm/mach-at91/clock.c * Copyright (C) 2005 David Brownell * Copyright (C) 2005 Ivan Kokshaysky * diff --git a/include/asm-arm/arch-at91/at91_aic.h b/include/asm-arm/arch-at91/at91_aic.h new file mode 100644 index 000000000000..df44c12a12d4 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_aic.h @@ -0,0 +1,53 @@ +/* + * include/asm-arm/arch-at91/at91_aic.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Advanced Interrupt Controller (AIC) - System peripherals registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_AIC_H +#define AT91_AIC_H + +#define AT91_AIC_SMR(n) (AT91_AIC + ((n) * 4)) /* Source Mode Registers 0-31 */ +#define AT91_AIC_PRIOR (7 << 0) /* Priority Level */ +#define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */ +#define AT91_AIC_SRCTYPE_LOW (0 << 5) +#define AT91_AIC_SRCTYPE_FALLING (1 << 5) +#define AT91_AIC_SRCTYPE_HIGH (2 << 5) +#define AT91_AIC_SRCTYPE_RISING (3 << 5) + +#define AT91_AIC_SVR(n) (AT91_AIC + 0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */ +#define AT91_AIC_IVR (AT91_AIC + 0x100) /* Interrupt Vector Register */ +#define AT91_AIC_FVR (AT91_AIC + 0x104) /* Fast Interrupt Vector Register */ +#define AT91_AIC_ISR (AT91_AIC + 0x108) /* Interrupt Status Register */ +#define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */ + +#define AT91_AIC_IPR (AT91_AIC + 0x10c) /* Interrupt Pending Register */ +#define AT91_AIC_IMR (AT91_AIC + 0x110) /* Interrupt Mask Register */ +#define AT91_AIC_CISR (AT91_AIC + 0x114) /* Core Interrupt Status Register */ +#define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */ +#define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */ + +#define AT91_AIC_IECR (AT91_AIC + 0x120) /* Interrupt Enable Command Register */ +#define AT91_AIC_IDCR (AT91_AIC + 0x124) /* Interrupt Disable Command Register */ +#define AT91_AIC_ICCR (AT91_AIC + 0x128) /* Interrupt Clear Command Register */ +#define AT91_AIC_ISCR (AT91_AIC + 0x12c) /* Interrupt Set Command Register */ +#define AT91_AIC_EOICR (AT91_AIC + 0x130) /* End of Interrupt Command Register */ +#define AT91_AIC_SPU (AT91_AIC + 0x134) /* Spurious Interrupt Vector Register */ +#define AT91_AIC_DCR (AT91_AIC + 0x138) /* Debug Control Register */ +#define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */ +#define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */ + +#define AT91_AIC_FFER (AT91_AIC + 0x140) /* Fast Forcing Enable Register [SAM9 only] */ +#define AT91_AIC_FFDR (AT91_AIC + 0x144) /* Fast Forcing Disable Register [SAM9 only] */ +#define AT91_AIC_FFSR (AT91_AIC + 0x148) /* Fast Forcing Status Register [SAM9 only] */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_dbgu.h b/include/asm-arm/arch-at91/at91_dbgu.h new file mode 100644 index 000000000000..1002a808ad91 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_dbgu.h @@ -0,0 +1,45 @@ +/* + * include/asm-arm/arch-at91/at91_dbgu.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Debug Unit (DBGU) - System peripherals registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_DBGU_H +#define AT91_DBGU_H + +#define AT91_DBGU_CR (AT91_DBGU + 0x00) /* Control Register */ +#define AT91_DBGU_MR (AT91_DBGU + 0x04) /* Mode Register */ +#define AT91_DBGU_IER (AT91_DBGU + 0x08) /* Interrupt Enable Register */ +#define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */ +#define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */ +#define AT91_DBGU_IDR (AT91_DBGU + 0x0c) /* Interrupt Disable Register */ +#define AT91_DBGU_IMR (AT91_DBGU + 0x10) /* Interrupt Mask Register */ +#define AT91_DBGU_SR (AT91_DBGU + 0x14) /* Status Register */ +#define AT91_DBGU_RHR (AT91_DBGU + 0x18) /* Receiver Holding Register */ +#define AT91_DBGU_THR (AT91_DBGU + 0x1c) /* Transmitter Holding Register */ +#define AT91_DBGU_BRGR (AT91_DBGU + 0x20) /* Baud Rate Generator Register */ + +#define AT91_DBGU_CIDR (AT91_DBGU + 0x40) /* Chip ID Register */ +#define AT91_DBGU_EXID (AT91_DBGU + 0x44) /* Chip ID Extension Register */ +#define AT91_CIDR_VERSION (0x1f << 0) /* Version of the Device */ +#define AT91_CIDR_EPROC (7 << 5) /* Embedded Processor */ +#define AT91_CIDR_NVPSIZ (0xf << 8) /* Nonvolatile Program Memory Size */ +#define AT91_CIDR_NVPSIZ2 (0xf << 12) /* Second Nonvolatile Program Memory Size */ +#define AT91_CIDR_SRAMSIZ (0xf << 16) /* Internal SRAM Size */ +#define AT91_CIDR_ARCH (0xff << 20) /* Architecture Identifier */ +#define AT91_CIDR_NVPTYP (7 << 28) /* Nonvolatile Program Memory Type */ +#define AT91_CIDR_EXT (1 << 31) /* Extension Flag */ + +#define AT91_DBGU_FNR (AT91_DBGU + 0x48) /* Force NTRST Register [SAM9 only] */ +#define AT91_DBGU_FNTRST (1 << 0) /* Force NTRST */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_ecc.h b/include/asm-arm/arch-at91/at91_ecc.h new file mode 100644 index 000000000000..ff93df516d6d --- /dev/null +++ b/include/asm-arm/arch-at91/at91_ecc.h @@ -0,0 +1,38 @@ +/* + * include/asm-arm/arch-at91/at91_ecc.h + * + * Error Corrected Code Controller (ECC) - System peripherals regsters. + * Based on AT91SAM9260 datasheet revision B. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef AT91_ECC_H +#define AT91_ECC_H + +#define AT91_ECC_CR (AT91_ECC + 0x00) /* Control register */ +#define AT91_ECC_RST (1 << 0) /* Reset parity */ + +#define AT91_ECC_MR (AT91_ECC + 0x04) /* Mode register */ +#define AT91_ECC_PAGESIZE (3 << 0) /* Page Size */ +#define AT91_ECC_PAGESIZE_528 (0) +#define AT91_ECC_PAGESIZE_1056 (1) +#define AT91_ECC_PAGESIZE_2112 (2) +#define AT91_ECC_PAGESIZE_4224 (3) + +#define AT91_ECC_SR (AT91_ECC + 0x08) /* Status register */ +#define AT91_ECC_RECERR (1 << 0) /* Recoverable Error */ +#define AT91_ECC_ECCERR (1 << 1) /* ECC Single Bit Error */ +#define AT91_ECC_MULERR (1 << 2) /* Multiple Errors */ + +#define AT91_ECC_PR (AT91_ECC + 0x0c) /* Parity register */ +#define AT91_ECC_BITADDR (0xf << 0) /* Bit Error Address */ +#define AT91_ECC_WORDADDR (0xfff << 4) /* Word Error Address */ + +#define AT91_ECC_NPR (AT91_ECC + 0x10) /* NParity register */ +#define AT91_ECC_NPARITY (0xffff << 0) /* NParity */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_lcdc.h b/include/asm-arm/arch-at91/at91_lcdc.h new file mode 100644 index 000000000000..ab040a40d37b --- /dev/null +++ b/include/asm-arm/arch-at91/at91_lcdc.h @@ -0,0 +1,148 @@ +/* + * include/asm-arm/arch-at91/at91_lcdc.h + * + * LCD Controller (LCDC). + * Based on AT91SAM9261 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_LCDC_H +#define AT91_LCDC_H + +#define AT91_LCDC_DMABADDR1 0x00 /* DMA Base Address Register 1 */ +#define AT91_LCDC_DMABADDR2 0x04 /* DMA Base Address Register 2 */ +#define AT91_LCDC_DMAFRMPT1 0x08 /* DMA Frame Pointer Register 1 */ +#define AT91_LCDC_DMAFRMPT2 0x0c /* DMA Frame Pointer Register 2 */ +#define AT91_LCDC_DMAFRMADD1 0x10 /* DMA Frame Address Register 1 */ +#define AT91_LCDC_DMAFRMADD2 0x14 /* DMA Frame Address Register 2 */ + +#define AT91_LCDC_DMAFRMCFG 0x18 /* DMA Frame Configuration Register */ +#define AT91_LCDC_FRSIZE (0x7fffff << 0) /* Frame Size */ +#define AT91_LCDC_BLENGTH (0x7f << 24) /* Burst Length */ + +#define AT91_LCDC_DMACON 0x1c /* DMA Control Register */ +#define AT91_LCDC_DMAEN (0x1 << 0) /* DMA Enable */ +#define AT91_LCDC_DMARST (0x1 << 1) /* DMA Reset */ +#define AT91_LCDC_DMABUSY (0x1 << 2) /* DMA Busy */ + +#define AT91_LCDC_LCDCON1 0x0800 /* LCD Control Register 1 */ +#define AT91_LCDC_BYPASS (1 << 0) /* Bypass lcd_dotck divider */ +#define AT91_LCDC_CLKVAL (0x1ff << 12) /* Clock Divider */ +#define AT91_LCDC_LINCNT (0x7ff << 21) /* Line Counter */ + +#define AT91_LCDC_LCDCON2 0x0804 /* LCD Control Register 2 */ +#define AT91_LCDC_DISTYPE (3 << 0) /* Display Type */ +#define AT91_LCDC_DISTYPE_STNMONO (0 << 0) +#define AT91_LCDC_DISTYPE_STNCOLOR (1 << 0) +#define AT91_LCDC_DISTYPE_TFT (2 << 0) +#define AT91_LCDC_SCANMOD (1 << 2) /* Scan Mode */ +#define AT91_LCDC_SCANMOD_SINGLE (0 << 2) +#define AT91_LCDC_SCANMOD_DUAL (1 << 2) +#define AT91_LCDC_IFWIDTH (3 << 3) /*Interface Width */ +#define AT91_LCDC_IFWIDTH_4 (0 << 3) +#define AT91_LCDC_IFWIDTH_8 (1 << 3) +#define AT91_LCDC_IFWIDTH_16 (2 << 3) +#define AT91_LCDC_PIXELSIZE (7 << 5) /* Bits per pixel */ +#define AT91_LCDC_PIXELSIZE_1 (0 << 5) +#define AT91_LCDC_PIXELSIZE_2 (1 << 5) +#define AT91_LCDC_PIXELSIZE_4 (2 << 5) +#define AT91_LCDC_PIXELSIZE_8 (3 << 5) +#define AT91_LCDC_PIXELSIZE_16 (4 << 5) +#define AT91_LCDC_PIXELSIZE_24 (5 << 5) +#define AT91_LCDC_INVVD (1 << 8) /* LCD Data polarity */ +#define AT91_LCDC_INVVD_NORMAL (0 << 8) +#define AT91_LCDC_INVVD_INVERTED (1 << 8) +#define AT91_LCDC_INVFRAME (1 << 9 ) /* LCD VSync polarity */ +#define AT91_LCDC_INVFRAME_NORMAL (0 << 9) +#define AT91_LCDC_INVFRAME_INVERTED (1 << 9) +#define AT91_LCDC_INVLINE (1 << 10) /* LCD HSync polarity */ +#define AT91_LCDC_INVLINE_NORMAL (0 << 10) +#define AT91_LCDC_INVLINE_INVERTED (1 << 10) +#define AT91_LCDC_INVCLK (1 << 11) /* LCD dotclk polarity */ +#define AT91_LCDC_INVCLK_NORMAL (0 << 11) +#define AT91_LCDC_INVCLK_INVERTED (1 << 11) +#define AT91_LCDC_INVDVAL (1 << 12) /* LCD dval polarity */ +#define AT91_LCDC_INVDVAL_NORMAL (0 << 12) +#define AT91_LCDC_INVDVAL_INVERTED (1 << 12) +#define AT91_LCDC_CLKMOD (1 << 15) /* LCD dotclk mode */ +#define AT91_LCDC_CLKMOD_ACTIVEDISPLAY (0 << 15) +#define AT91_LCDC_CLKMOD_ALWAYSACTIVE (1 << 15) +#define AT91_LCDC_MEMOR (1 << 31) /* Memory Ordering Format */ +#define AT91_LCDC_MEMOR_BIG (0 << 31) +#define AT91_LCDC_MEMOR_LITTLE (1 << 31) + +#define AT91_LCDC_TIM1 0x0808 /* LCD Timing Register 1 */ +#define AT91_LCDC_VFP (0xff << 0) /* Vertical Front Porch */ +#define AT91_LCDC_VBP (0xff << 8) /* Vertical Back Porch */ +#define AT91_LCDC_VPW (0x3f << 16) /* Vertical Synchronization Pulse Width */ +#define AT91_LCDC_VHDLY (0xf << 24) /* Vertical to Horizontal Delay */ + +#define AT91_LCDC_TIM2 0x080c /* LCD Timing Register 2 */ +#define AT91_LCDC_HBP (0xff << 0) /* Horizontal Back Porch */ +#define AT91_LCDC_HPW (0x3f << 8) /* Horizontal Synchronization Pulse Width */ +#define AT91_LCDC_HFP (0x7ff << 21) /* Horizontal Front Porch */ + +#define AT91_LCDC_LCDFRMCFG 0x0810 /* LCD Frame Configuration Register */ +#define AT91_LCDC_LINEVAL (0x7ff << 0) /* Vertical Size of LCD Module */ +#define AT91_LCDC_HOZVAL (0x7ff << 21) /* Horizontal Size of LCD Module */ + +#define AT91_LCDC_FIFO 0x0814 /* LCD FIFO Register */ +#define AT91_LCDC_FIFOTH (0xffff) /* FIFO Threshold */ + +#define AT91_LCDC_DP1_2 0x081c /* Dithering Pattern DP1_2 Register */ +#define AT91_LCDC_DP4_7 0x0820 /* Dithering Pattern DP4_7 Register */ +#define AT91_LCDC_DP3_5 0x0824 /* Dithering Pattern DP3_5 Register */ +#define AT91_LCDC_DP2_3 0x0828 /* Dithering Pattern DP2_3 Register */ +#define AT91_LCDC_DP5_7 0x082c /* Dithering Pattern DP5_7 Register */ +#define AT91_LCDC_DP3_4 0x0830 /* Dithering Pattern DP3_4 Register */ +#define AT91_LCDC_DP4_5 0x0834 /* Dithering Pattern DP4_5 Register */ +#define AT91_LCDC_DP6_7 0x0838 /* Dithering Pattern DP6_7 Register */ +#define AT91_LCDC_DP1_2_VAL (0xff) +#define AT91_LCDC_DP4_7_VAL (0xfffffff) +#define AT91_LCDC_DP3_5_VAL (0xfffff) +#define AT91_LCDC_DP2_3_VAL (0xfff) +#define AT91_LCDC_DP5_7_VAL (0xfffffff) +#define AT91_LCDC_DP3_4_VAL (0xffff) +#define AT91_LCDC_DP4_5_VAL (0xfffff) +#define AT91_LCDC_DP6_7_VAL (0xfffffff) + +#define AT91_LCDC_PWRCON 0x083c /* Power Control Register */ +#define AT91_LCDC_PWR (1 << 0) /* LCD Module Power Control */ +#define AT91_LCDC_GUARDT (0x7f << 1) /* Delay in Frame Period */ +#define AT91_LCDC_BUSY (1 << 31) /* LCD Busy */ + +#define AT91_LCDC_CONTRAST_CTR 0x0840 /* Contrast Control Register */ +#define AT91_LCDC_PS (3 << 0) /* Contrast Counter Prescaler */ +#define AT91_LCDC_PS_DIV1 (0 << 0) +#define AT91_LCDC_PS_DIV2 (1 << 0) +#define AT91_LCDC_PS_DIV4 (2 << 0) +#define AT91_LCDC_PS_DIV8 (3 << 0) +#define AT91_LCDC_POL (1 << 2) /* Polarity of output Pulse */ +#define AT91_LCDC_POL_NEGATIVE (0 << 2) +#define AT91_LCDC_POL_POSITIVE (1 << 2) +#define AT91_LCDC_ENA (1 << 3) /* PWM generator Control */ +#define AT91_LCDC_ENA_PWMDISABLE (0 << 3) +#define AT91_LCDC_ENA_PWMENABLE (1 << 3) + +#define AT91_LCDC_CONTRAST_VAL 0x0844 /* Contrast Value Register */ +#define AT91_LCDC_CVAL (0xff) /* PWM compare value */ + +#define AT91_LCDC_IER 0x0848 /* Interrupt Enable Register */ +#define AT91_LCDC_IDR 0x084c /* Interrupt Disable Register */ +#define AT91_LCDC_IMR 0x0850 /* Interrupt Mask Register */ +#define AT91_LCDC_ISR 0x0854 /* Interrupt Enable Register */ +#define AT91_LCDC_ICR 0x0858 /* Interrupt Clear Register */ +#define AT91_LCDC_LNI (1 << 0) /* Line Interrupt */ +#define AT91_LCDC_LSTLNI (1 << 1) /* Last Line Interrupt */ +#define AT91_LCDC_EOFI (1 << 2) /* DMA End Of Frame Interrupt */ +#define AT91_LCDC_UFLWI (1 << 4) /* FIFO Underflow Interrupt */ +#define AT91_LCDC_OWRI (1 << 5) /* FIFO Overwrite Interrupt */ +#define AT91_LCDC_MERI (1 << 6) /* DMA Memory Error Interrupt */ + +#define AT91_LCDC_LUT_(n) (0x0c00 + ((n)*4)) /* Palette Entry 0..255 */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_mci.h b/include/asm-arm/arch-at91/at91_mci.h new file mode 100644 index 000000000000..40a9876b661a --- /dev/null +++ b/include/asm-arm/arch-at91/at91_mci.h @@ -0,0 +1,106 @@ +/* + * include/asm-arm/arch-at91/at91_mci.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * MultiMedia Card Interface (MCI) registers. + * Based on AT91RM9200 datasheet revision F. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_MCI_H +#define AT91_MCI_H + +#define AT91_MCI_CR 0x00 /* Control Register */ +#define AT91_MCI_MCIEN (1 << 0) /* Multi-Media Interface Enable */ +#define AT91_MCI_MCIDIS (1 << 1) /* Multi-Media Interface Disable */ +#define AT91_MCI_PWSEN (1 << 2) /* Power Save Mode Enable */ +#define AT91_MCI_PWSDIS (1 << 3) /* Power Save Mode Disable */ +#define AT91_MCI_SWRST (1 << 7) /* Software Reset */ + +#define AT91_MCI_MR 0x04 /* Mode Register */ +#define AT91_MCI_CLKDIV (0xff << 0) /* Clock Divider */ +#define AT91_MCI_PWSDIV (7 << 8) /* Power Saving Divider */ +#define AT91_MCI_PDCPADV (1 << 14) /* PDC Padding Value */ +#define AT91_MCI_PDCMODE (1 << 15) /* PDC-orientated Mode */ +#define AT91_MCI_BLKLEN (0xfff << 18) /* Data Block Length */ + +#define AT91_MCI_DTOR 0x08 /* Data Timeout Register */ +#define AT91_MCI_DTOCYC (0xf << 0) /* Data Timeout Cycle Number */ +#define AT91_MCI_DTOMUL (7 << 4) /* Data Timeout Multiplier */ +#define AT91_MCI_DTOMUL_1 (0 << 4) +#define AT91_MCI_DTOMUL_16 (1 << 4) +#define AT91_MCI_DTOMUL_128 (2 << 4) +#define AT91_MCI_DTOMUL_256 (3 << 4) +#define AT91_MCI_DTOMUL_1K (4 << 4) +#define AT91_MCI_DTOMUL_4K (5 << 4) +#define AT91_MCI_DTOMUL_64K (6 << 4) +#define AT91_MCI_DTOMUL_1M (7 << 4) + +#define AT91_MCI_SDCR 0x0c /* SD Card Register */ +#define AT91_MCI_SDCSEL (3 << 0) /* SD Card Selector */ +#define AT91_MCI_SDCBUS (1 << 7) /* 1-bit or 4-bit bus */ + +#define AT91_MCI_ARGR 0x10 /* Argument Register */ + +#define AT91_MCI_CMDR 0x14 /* Command Register */ +#define AT91_MCI_CMDNB (0x3f << 0) /* Command Number */ +#define AT91_MCI_RSPTYP (3 << 6) /* Response Type */ +#define AT91_MCI_RSPTYP_NONE (0 << 6) +#define AT91_MCI_RSPTYP_48 (1 << 6) +#define AT91_MCI_RSPTYP_136 (2 << 6) +#define AT91_MCI_SPCMD (7 << 8) /* Special Command */ +#define AT91_MCI_SPCMD_NONE (0 << 8) +#define AT91_MCI_SPCMD_INIT (1 << 8) +#define AT91_MCI_SPCMD_SYNC (2 << 8) +#define AT91_MCI_SPCMD_ICMD (4 << 8) +#define AT91_MCI_SPCMD_IRESP (5 << 8) +#define AT91_MCI_OPDCMD (1 << 11) /* Open Drain Command */ +#define AT91_MCI_MAXLAT (1 << 12) /* Max Latency for Command to Response */ +#define AT91_MCI_TRCMD (3 << 16) /* Transfer Command */ +#define AT91_MCI_TRCMD_NONE (0 << 16) +#define AT91_MCI_TRCMD_START (1 << 16) +#define AT91_MCI_TRCMD_STOP (2 << 16) +#define AT91_MCI_TRDIR (1 << 18) /* Transfer Direction */ +#define AT91_MCI_TRTYP (3 << 19) /* Transfer Type */ +#define AT91_MCI_TRTYP_BLOCK (0 << 19) +#define AT91_MCI_TRTYP_MULTIPLE (1 << 19) +#define AT91_MCI_TRTYP_STREAM (2 << 19) + +#define AT91_MCI_RSPR(n) (0x20 + ((n) * 4)) /* Response Registers 0-3 */ +#define AT91_MCR_RDR 0x30 /* Receive Data Register */ +#define AT91_MCR_TDR 0x34 /* Transmit Data Register */ + +#define AT91_MCI_SR 0x40 /* Status Register */ +#define AT91_MCI_CMDRDY (1 << 0) /* Command Ready */ +#define AT91_MCI_RXRDY (1 << 1) /* Receiver Ready */ +#define AT91_MCI_TXRDY (1 << 2) /* Transmit Ready */ +#define AT91_MCI_BLKE (1 << 3) /* Data Block Ended */ +#define AT91_MCI_DTIP (1 << 4) /* Data Transfer in Progress */ +#define AT91_MCI_NOTBUSY (1 << 5) /* Data Not Busy */ +#define AT91_MCI_ENDRX (1 << 6) /* End of RX Buffer */ +#define AT91_MCI_ENDTX (1 << 7) /* End fo TX Buffer */ +#define AT91_MCI_SDIOIRQA (1 << 8) /* SDIO Interrupt for Slot A */ +#define At91_MCI_SDIOIRQB (1 << 9) /* SDIO Interrupt for Slot B [AT91RM9200 only] */ +#define AT91_MCI_RXBUFF (1 << 14) /* RX Buffer Full */ +#define AT91_MCI_TXBUFE (1 << 15) /* TX Buffer Empty */ +#define AT91_MCI_RINDE (1 << 16) /* Response Index Error */ +#define AT91_MCI_RDIRE (1 << 17) /* Response Direction Error */ +#define AT91_MCI_RCRCE (1 << 18) /* Response CRC Error */ +#define AT91_MCI_RENDE (1 << 19) /* Response End Bit Error */ +#define AT91_MCI_RTOE (1 << 20) /* Reponse Time-out Error */ +#define AT91_MCI_DCRCE (1 << 21) /* Data CRC Error */ +#define AT91_MCI_DTOE (1 << 22) /* Data Time-out Error */ +#define AT91_MCI_OVRE (1 << 30) /* Overrun */ +#define AT91_MCI_UNRE (1 << 31) /* Underrun */ + +#define AT91_MCI_IER 0x44 /* Interrupt Enable Register */ +#define AT91_MCI_IDR 0x48 /* Interrupt Disable Register */ +#define AT91_MCI_IMR 0x4c /* Interrupt Mask Register */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_pdc.h b/include/asm-arm/arch-at91/at91_pdc.h new file mode 100644 index 000000000000..a54adf52c65d --- /dev/null +++ b/include/asm-arm/arch-at91/at91_pdc.h @@ -0,0 +1,36 @@ +/* + * include/asm-arm/arch-at91/at91_pdc.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Peripheral Data Controller (PDC) registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_PDC_H +#define AT91_PDC_H + +#define AT91_PDC_RPR 0x100 /* Receive Pointer Register */ +#define AT91_PDC_RCR 0x104 /* Receive Counter Register */ +#define AT91_PDC_TPR 0x108 /* Transmit Pointer Register */ +#define AT91_PDC_TCR 0x10c /* Transmit Counter Register */ +#define AT91_PDC_RNPR 0x110 /* Receive Next Pointer Register */ +#define AT91_PDC_RNCR 0x114 /* Receive Next Counter Register */ +#define AT91_PDC_TNPR 0x118 /* Transmit Next Pointer Register */ +#define AT91_PDC_TNCR 0x11c /* Transmit Next Counter Register */ + +#define AT91_PDC_PTCR 0x120 /* Transfer Control Register */ +#define AT91_PDC_RXTEN (1 << 0) /* Receiver Transfer Enable */ +#define AT91_PDC_RXTDIS (1 << 1) /* Receiver Transfer Disable */ +#define AT91_PDC_TXTEN (1 << 8) /* Transmitter Transfer Enable */ +#define AT91_PDC_TXTDIS (1 << 9) /* Transmitter Transfer Disable */ + +#define AT91_PDC_PTSR 0x124 /* Transfer Status Register */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_pio.h b/include/asm-arm/arch-at91/at91_pio.h new file mode 100644 index 000000000000..84c3866d309f --- /dev/null +++ b/include/asm-arm/arch-at91/at91_pio.h @@ -0,0 +1,49 @@ +/* + * include/asm-arm/arch-at91/at91_pio.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Parallel I/O Controller (PIO) - System peripherals registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_PIO_H +#define AT91_PIO_H + +#define PIO_PER 0x00 /* Enable Register */ +#define PIO_PDR 0x04 /* Disable Register */ +#define PIO_PSR 0x08 /* Status Register */ +#define PIO_OER 0x10 /* Output Enable Register */ +#define PIO_ODR 0x14 /* Output Disable Register */ +#define PIO_OSR 0x18 /* Output Status Register */ +#define PIO_IFER 0x20 /* Glitch Input Filter Enable */ +#define PIO_IFDR 0x24 /* Glitch Input Filter Disable */ +#define PIO_IFSR 0x28 /* Glitch Input Filter Status */ +#define PIO_SODR 0x30 /* Set Output Data Register */ +#define PIO_CODR 0x34 /* Clear Output Data Register */ +#define PIO_ODSR 0x38 /* Output Data Status Register */ +#define PIO_PDSR 0x3c /* Pin Data Status Register */ +#define PIO_IER 0x40 /* Interrupt Enable Register */ +#define PIO_IDR 0x44 /* Interrupt Disable Register */ +#define PIO_IMR 0x48 /* Interrupt Mask Register */ +#define PIO_ISR 0x4c /* Interrupt Status Register */ +#define PIO_MDER 0x50 /* Multi-driver Enable Register */ +#define PIO_MDDR 0x54 /* Multi-driver Disable Register */ +#define PIO_MDSR 0x58 /* Multi-driver Status Register */ +#define PIO_PUDR 0x60 /* Pull-up Disable Register */ +#define PIO_PUER 0x64 /* Pull-up Enable Register */ +#define PIO_PUSR 0x68 /* Pull-up Status Register */ +#define PIO_ASR 0x70 /* Peripheral A Select Register */ +#define PIO_BSR 0x74 /* Peripheral B Select Register */ +#define PIO_ABSR 0x78 /* AB Status Register */ +#define PIO_OWER 0xa0 /* Output Write Enable Register */ +#define PIO_OWDR 0xa4 /* Output Write Disable Register */ +#define PIO_OWSR 0xa8 /* Output Write Status Register */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_pit.h b/include/asm-arm/arch-at91/at91_pit.h new file mode 100644 index 000000000000..5026325a5ae4 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_pit.h @@ -0,0 +1,29 @@ +/* + * include/asm-arm/arch-at91/at91_pit.h + * + * Periodic Interval Timer (PIT) - System peripherals regsters. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_PIT_H +#define AT91_PIT_H + +#define AT91_PIT_MR (AT91_PIT + 0x00) /* Mode Register */ +#define AT91_PIT_PITIEN (1 << 25) /* Timer Interrupt Enable */ +#define AT91_PIT_PITEN (1 << 24) /* Timer Enabled */ +#define AT91_PIT_PIV (0xfffff) /* Periodic Interval Value */ + +#define AT91_PIT_SR (AT91_PIT + 0x04) /* Status Register */ +#define AT91_PIT_PITS (1 << 0) /* Timer Status */ + +#define AT91_PIT_PIVR (AT91_PIT + 0x08) /* Periodic Interval Value Register */ +#define AT91_PIT_PIIR (AT91_PIT + 0x0c) /* Periodic Interval Image Register */ +#define AT91_PIT_PICNT (0xfff << 20) /* Interval Counter */ +#define AT91_PIT_CPIV (0xfffff) /* Inverval Value */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_pmc.h b/include/asm-arm/arch-at91/at91_pmc.h new file mode 100644 index 000000000000..33ff5b6798ee --- /dev/null +++ b/include/asm-arm/arch-at91/at91_pmc.h @@ -0,0 +1,92 @@ +/* + * include/asm-arm/arch-at91/at91_pmc.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Power Management Controller (PMC) - System peripherals registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_PMC_H +#define AT91_PMC_H + +#define AT91_PMC_SCER (AT91_PMC + 0x00) /* System Clock Enable Register */ +#define AT91_PMC_SCDR (AT91_PMC + 0x04) /* System Clock Disable Register */ + +#define AT91_PMC_SCSR (AT91_PMC + 0x08) /* System Clock Status Register */ +#define AT91_PMC_PCK (1 << 0) /* Processor Clock */ +#define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */ +#define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */ +#define AT91RM9200_PMC_UHP (1 << 4) /* USB Host Port Clock [AT91RM9200 only] */ +#define AT91SAM926x_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91SAM926x only] */ +#define AT91SAM926x_PMC_UDP (1 << 7) /* USB Devcice Port Clock [AT91SAM926x only] */ +#define AT91_PMC_PCK0 (1 << 8) /* Programmable Clock 0 */ +#define AT91_PMC_PCK1 (1 << 9) /* Programmable Clock 1 */ +#define AT91_PMC_PCK2 (1 << 10) /* Programmable Clock 2 */ +#define AT91_PMC_PCK3 (1 << 11) /* Programmable Clock 3 */ +#define AT91_PMC_HCK0 (1 << 16) /* AHB Clock (USB host) [AT91SAM9261 only] */ +#define AT91_PMC_HCK1 (1 << 17) /* AHB Clock (LCD) [AT91SAM9261 only] */ + +#define AT91_PMC_PCER (AT91_PMC + 0x10) /* Peripheral Clock Enable Register */ +#define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */ +#define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */ + +#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register */ +#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ +#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */ +#define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ + +#define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */ +#define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */ +#define AT91_PMC_MAINRDY (1 << 16) /* Main Clock Ready */ + +#define AT91_CKGR_PLLAR (AT91_PMC + 0x28) /* PLL A Register */ +#define AT91_CKGR_PLLBR (AT91_PMC + 0x2c) /* PLL B Register */ +#define AT91_PMC_DIV (0xff << 0) /* Divider */ +#define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */ +#define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */ +#define AT91_PMC_MUL (0x7ff << 16) /* PLL Multiplier */ +#define AT91_PMC_USB96M (1 << 28) /* Divider by 2 Enable (PLLB only) */ + +#define AT91_PMC_MCKR (AT91_PMC + 0x30) /* Master Clock Register */ +#define AT91_PMC_CSS (3 << 0) /* Master Clock Selection */ +#define AT91_PMC_CSS_SLOW (0 << 0) +#define AT91_PMC_CSS_MAIN (1 << 0) +#define AT91_PMC_CSS_PLLA (2 << 0) +#define AT91_PMC_CSS_PLLB (3 << 0) +#define AT91_PMC_PRES (7 << 2) /* Master Clock Prescaler */ +#define AT91_PMC_PRES_1 (0 << 2) +#define AT91_PMC_PRES_2 (1 << 2) +#define AT91_PMC_PRES_4 (2 << 2) +#define AT91_PMC_PRES_8 (3 << 2) +#define AT91_PMC_PRES_16 (4 << 2) +#define AT91_PMC_PRES_32 (5 << 2) +#define AT91_PMC_PRES_64 (6 << 2) +#define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */ +#define AT91_PMC_MDIV_1 (0 << 8) +#define AT91_PMC_MDIV_2 (1 << 8) +#define AT91_PMC_MDIV_3 (2 << 8) +#define AT91_PMC_MDIV_4 (3 << 8) + +#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-3 Registers */ + +#define AT91_PMC_IER (AT91_PMC + 0x60) /* Interrupt Enable Register */ +#define AT91_PMC_IDR (AT91_PMC + 0x64) /* Interrupt Disable Register */ +#define AT91_PMC_SR (AT91_PMC + 0x68) /* Status Register */ +#define AT91_PMC_MOSCS (1 << 0) /* MOSCS Flag */ +#define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */ +#define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */ +#define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */ +#define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */ +#define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */ +#define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */ +#define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */ +#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_rstc.h b/include/asm-arm/arch-at91/at91_rstc.h new file mode 100644 index 000000000000..0b7afbc015a2 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_rstc.h @@ -0,0 +1,39 @@ +/* + * include/asm-arm/arch-at91/at91_rstc.h + * + * Reset Controller (RSTC) - System peripherals regsters. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_RSTC_H +#define AT91_RSTC_H + +#define AT91_RSTC_CR (AT91_RSTC + 0x00) /* Reset Controller Control Register */ +#define AT91_RSTC_PROCRST (1 << 0) /* Processor Reset */ +#define AT91_RSTC_PERRST (1 << 2) /* Peripheral Reset */ +#define AT91_RSTC_EXTRST (1 << 3) /* External Reset */ +#define AT91_RSTC_KEY (0xff << 24) /* KEY Password */ + +#define AT91_RSTC_SR (AT91_RSTC + 0x04) /* Reset Controller Status Register */ +#define AT91_RSTC_URSTS (1 << 0) /* User Reset Status */ +#define AT91_RSTC_RSTTYP (7 << 8) /* Reset Type */ +#define AT91_RSTC_RSTTYP_GENERAL (0 << 8) +#define AT91_RSTC_RSTTYP_WAKEUP (1 << 8) +#define AT91_RSTC_RSTTYP_WATCHDOG (2 << 8) +#define AT91_RSTC_RSTTYP_SOFTWARE (3 << 8) +#define AT91_RSTC_RSTTYP_USER (4 << 8) +#define AT91_RSTC_NRSTL (1 << 16) /* NRST Pin Level */ +#define AT91_RSTC_SRCMP (1 << 17) /* Software Reset Command in Progress */ + +#define AT91_RSTC_MR (AT91_RSTC + 0x08) /* Reset Controller Mode Register */ +#define AT91_RSTC_URSTEN (1 << 0) /* User Reset Enable */ +#define AT91_RSTC_URSTIEN (1 << 4) /* User Reset Interrupt Enable */ +#define AT91_RSTC_ERSTL (0xf << 8) /* External Reset Length */ +#define AT91_RSTC_KEY (0xff << 24) /* KEY Password */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_rtc.h b/include/asm-arm/arch-at91/at91_rtc.h new file mode 100644 index 000000000000..af9bd28174c0 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_rtc.h @@ -0,0 +1,75 @@ +/* + * include/asm-arm/arch-at91/at91_rtc.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Real Time Clock (RTC) - System peripheral registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_RTC_H +#define AT91_RTC_H + +#define AT91_RTC_CR (AT91_RTC + 0x00) /* Control Register */ +#define AT91_RTC_UPDTIM (1 << 0) /* Update Request Time Register */ +#define AT91_RTC_UPDCAL (1 << 1) /* Update Request Calendar Register */ +#define AT91_RTC_TIMEVSEL (3 << 8) /* Time Event Selection */ +#define AT91_RTC_TIMEVSEL_MINUTE (0 << 8) +#define AT91_RTC_TIMEVSEL_HOUR (1 << 8) +#define AT91_RTC_TIMEVSEL_DAY24 (2 << 8) +#define AT91_RTC_TIMEVSEL_DAY12 (3 << 8) +#define AT91_RTC_CALEVSEL (3 << 16) /* Calendar Event Selection */ +#define AT91_RTC_CALEVSEL_WEEK (0 << 16) +#define AT91_RTC_CALEVSEL_MONTH (1 << 16) +#define AT91_RTC_CALEVSEL_YEAR (2 << 16) + +#define AT91_RTC_MR (AT91_RTC + 0x04) /* Mode Register */ +#define AT91_RTC_HRMOD (1 << 0) /* 12/24 Hour Mode */ + +#define AT91_RTC_TIMR (AT91_RTC + 0x08) /* Time Register */ +#define AT91_RTC_SEC (0x7f << 0) /* Current Second */ +#define AT91_RTC_MIN (0x7f << 8) /* Current Minute */ +#define AT91_RTC_HOUR (0x3f << 16) /* Current Hour */ +#define AT91_RTC_AMPM (1 << 22) /* Ante Meridiem Post Meridiem Indicator */ + +#define AT91_RTC_CALR (AT91_RTC + 0x0c) /* Calendar Register */ +#define AT91_RTC_CENT (0x7f << 0) /* Current Century */ +#define AT91_RTC_YEAR (0xff << 8) /* Current Year */ +#define AT91_RTC_MONTH (0x1f << 16) /* Current Month */ +#define AT91_RTC_DAY (7 << 21) /* Current Day */ +#define AT91_RTC_DATE (0x3f << 24) /* Current Date */ + +#define AT91_RTC_TIMALR (AT91_RTC + 0x10) /* Time Alarm Register */ +#define AT91_RTC_SECEN (1 << 7) /* Second Alarm Enable */ +#define AT91_RTC_MINEN (1 << 15) /* Minute Alarm Enable */ +#define AT91_RTC_HOUREN (1 << 23) /* Hour Alarm Enable */ + +#define AT91_RTC_CALALR (AT91_RTC + 0x14) /* Calendar Alarm Register */ +#define AT91_RTC_MTHEN (1 << 23) /* Month Alarm Enable */ +#define AT91_RTC_DATEEN (1 << 31) /* Date Alarm Enable */ + +#define AT91_RTC_SR (AT91_RTC + 0x18) /* Status Register */ +#define AT91_RTC_ACKUPD (1 << 0) /* Acknowledge for Update */ +#define AT91_RTC_ALARM (1 << 1) /* Alarm Flag */ +#define AT91_RTC_SECEV (1 << 2) /* Second Event */ +#define AT91_RTC_TIMEV (1 << 3) /* Time Event */ +#define AT91_RTC_CALEV (1 << 4) /* Calendar Event */ + +#define AT91_RTC_SCCR (AT91_RTC + 0x1c) /* Status Clear Command Register */ +#define AT91_RTC_IER (AT91_RTC + 0x20) /* Interrupt Enable Register */ +#define AT91_RTC_IDR (AT91_RTC + 0x24) /* Interrupt Disable Register */ +#define AT91_RTC_IMR (AT91_RTC + 0x28) /* Interrupt Mask Register */ + +#define AT91_RTC_VER (AT91_RTC + 0x2c) /* Valid Entry Register */ +#define AT91_RTC_NVTIM (1 << 0) /* Non valid Time */ +#define AT91_RTC_NVCAL (1 << 1) /* Non valid Calendar */ +#define AT91_RTC_NVTIMALR (1 << 2) /* Non valid Time Alarm */ +#define AT91_RTC_NVCALALR (1 << 3) /* Non valid Calendar Alarm */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_rtt.h b/include/asm-arm/arch-at91/at91_rtt.h new file mode 100644 index 000000000000..bae1103fbbb2 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_rtt.h @@ -0,0 +1,32 @@ +/* + * include/asm-arm/arch-at91/at91_rtt.h + * + * Real-time Timer (RTT) - System peripherals regsters. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_RTT_H +#define AT91_RTT_H + +#define AT91_RTT_MR (AT91_RTT + 0x00) /* Real-time Mode Register */ +#define AT91_RTT_RTPRES (0xffff << 0) /* Real-time Timer Prescaler Value */ +#define AT91_RTT_ALMIEN (1 << 16) /* Alarm Interrupt Enable */ +#define AT91_RTT_RTTINCIEN (1 << 17) /* Real Time Timer Increment Interrupt Enable */ +#define AT91_RTT_RTTRST (1 << 18) /* Real Time Timer Restart */ + +#define AT91_RTT_AR (AT91_RTT + 0x04) /* Real-time Alarm Register */ +#define AT91_RTT_ALMV (0xffffffff) /* Alarm Value */ + +#define AT91_RTT_VR (AT91_RTT + 0x08) /* Real-time Value Register */ +#define AT91_RTT_CRTV (0xffffffff) /* Current Real-time Value */ + +#define AT91_RTT_SR (AT91_RTT + 0x0c) /* Real-time Status Register */ +#define AT91_RTT_ALMS (1 << 0) /* Real-time Alarm Status */ +#define AT91_RTT_RTTINC (1 << 1) /* Real-time Timer Increment */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_shdwc.h b/include/asm-arm/arch-at91/at91_shdwc.h new file mode 100644 index 000000000000..795fcc266228 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_shdwc.h @@ -0,0 +1,33 @@ +/* + * include/asm-arm/arch-at91/at91_shdwc.h + * + * Shutdown Controller (SHDWC) - System peripherals regsters. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_SHDWC_H +#define AT91_SHDWC_H + +#define AT91_SHDW_CR (AT91_SHDWC + 0x00) /* Shut Down Control Register */ +#define AT91_SHDW_SHDW (1 << 0) /* Processor Reset */ +#define AT91_SHDW_KEY (0xff << 24) /* KEY Password */ + +#define AT91_SHDW_MR (AT91_SHDWC + 0x04) /* Shut Down Mode Register */ +#define AT91_SHDW_WKMODE0 (3 << 0) /* Wake-up 0 Mode Selection */ +#define AT91_SHDW_WKMODE0_NONE 0 +#define AT91_SHDW_WKMODE0_HIGH 1 +#define AT91_SHDW_WKMODE0_LOW 2 +#define AT91_SHDW_WKMODE0_ANYLEVEL 3 +#define AT91_SHDW_CPTWK0 (0xf << 4) /* Counter On Wake Up 0 */ +#define AT91_SHDW_RTTWKEN (1 << 16) /* Real Time Timer Wake-up Enable */ + +#define AT91_SHDW_SR (AT91_SHDWC + 0x08) /* Shut Down Status Register */ +#define AT91_SHDW_WAKEUP0 (1 << 0) /* Wake-up 0 Status */ +#define AT91_SHDW_RTTWK (1 << 16) /* Real-time Timer Wake-up */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_spi.h b/include/asm-arm/arch-at91/at91_spi.h new file mode 100644 index 000000000000..f9b9a8464997 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_spi.h @@ -0,0 +1,81 @@ +/* + * include/asm-arm/arch-at91/at91_spi.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Serial Peripheral Interface (SPI) registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_SPI_H +#define AT91_SPI_H + +#define AT91_SPI_CR 0x00 /* Control Register */ +#define AT91_SPI_SPIEN (1 << 0) /* SPI Enable */ +#define AT91_SPI_SPIDIS (1 << 1) /* SPI Disable */ +#define AT91_SPI_SWRST (1 << 7) /* SPI Software Reset */ +#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */ + +#define AT91_SPI_MR 0x04 /* Mode Register */ +#define AT91_SPI_MSTR (1 << 0) /* Master/Slave Mode */ +#define AT91_SPI_PS (1 << 1) /* Peripheral Select */ +#define AT91_SPI_PS_FIXED (0 << 1) +#define AT91_SPI_PS_VARIABLE (1 << 1) +#define AT91_SPI_PCSDEC (1 << 2) /* Chip Select Decode */ +#define AT91_SPI_DIV32 (1 << 3) /* Clock Selection [AT91RM9200 only] */ +#define AT91_SPI_MODFDIS (1 << 4) /* Mode Fault Detection */ +#define AT91_SPI_LLB (1 << 7) /* Local Loopback Enable */ +#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ +#define AT91_SPI_DLYBCS (0xff << 24) /* Delay Between Chip Selects */ + +#define AT91_SPI_RDR 0x08 /* Receive Data Register */ +#define AT91_SPI_RD (0xffff << 0) /* Receive Data */ +#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ + +#define AT91_SPI_TDR 0x0c /* Transmit Data Register */ +#define AT91_SPI_TD (0xffff << 0) /* Transmit Data */ +#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ +#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */ + +#define AT91_SPI_SR 0x10 /* Status Register */ +#define AT91_SPI_RDRF (1 << 0) /* Receive Data Register Full */ +#define AT91_SPI_TDRE (1 << 1) /* Transmit Data Register Full */ +#define AT91_SPI_MODF (1 << 2) /* Mode Fault Error */ +#define AT91_SPI_OVRES (1 << 3) /* Overrun Error Status */ +#define AT91_SPI_ENDRX (1 << 4) /* End of RX buffer */ +#define AT91_SPI_ENDTX (1 << 5) /* End of TX buffer */ +#define AT91_SPI_RXBUFF (1 << 6) /* RX Buffer Full */ +#define AT91_SPI_TXBUFE (1 << 7) /* TX Buffer Empty */ +#define AT91_SPI_NSSR (1 << 8) /* NSS Rising [SAM9261 only] */ +#define AT91_SPI_TXEMPTY (1 << 9) /* Transmission Register Empty [SAM9261 only] */ +#define AT91_SPI_SPIENS (1 << 16) /* SPI Enable Status */ + +#define AT91_SPI_IER 0x14 /* Interrupt Enable Register */ +#define AT91_SPI_IDR 0x18 /* Interrupt Disable Register */ +#define AT91_SPI_IMR 0x1c /* Interrupt Mask Register */ + +#define AT91_SPI_CSR(n) (0x30 + ((n) * 4)) /* Chip Select Registers 0-3 */ +#define AT91_SPI_CPOL (1 << 0) /* Clock Polarity */ +#define AT91_SPI_NCPHA (1 << 1) /* Clock Phase */ +#define AT91_SPI_CSAAT (1 << 3) /* Chip Select Active After Transfer [SAM9261 only] */ +#define AT91_SPI_BITS (0xf << 4) /* Bits Per Transfer */ +#define AT91_SPI_BITS_8 (0 << 4) +#define AT91_SPI_BITS_9 (1 << 4) +#define AT91_SPI_BITS_10 (2 << 4) +#define AT91_SPI_BITS_11 (3 << 4) +#define AT91_SPI_BITS_12 (4 << 4) +#define AT91_SPI_BITS_13 (5 << 4) +#define AT91_SPI_BITS_14 (6 << 4) +#define AT91_SPI_BITS_15 (7 << 4) +#define AT91_SPI_BITS_16 (8 << 4) +#define AT91_SPI_SCBR (0xff << 8) /* Serial Clock Baud Rate */ +#define AT91_SPI_DLYBS (0xff << 16) /* Delay before SPCK */ +#define AT91_SPI_DLYBCT (0xff << 24) /* Delay between Consecutive Transfers */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_ssc.h b/include/asm-arm/arch-at91/at91_ssc.h new file mode 100644 index 000000000000..0ecc73460b50 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_ssc.h @@ -0,0 +1,106 @@ +/* + * include/asm-arm/arch-at91/at91_ssc.h + * + * Copyright (C) SAN People + * + * Serial Synchronous Controller (SSC) registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_SSC_H +#define AT91_SSC_H + +#define AT91_SSC_CR 0x00 /* Control Register */ +#define AT91_SSC_RXEN (1 << 0) /* Receive Enable */ +#define AT91_SSC_RXDIS (1 << 1) /* Receive Disable */ +#define AT91_SSC_TXEN (1 << 8) /* Transmit Enable */ +#define AT91_SSC_TXDIS (1 << 9) /* Transmit Disable */ +#define AT91_SSC_SWRST (1 << 15) /* Software Reset */ + +#define AT91_SSC_CMR 0x04 /* Clock Mode Register */ +#define AT91_SSC_CMR_DIV (0xfff << 0) /* Clock Divider */ + +#define AT91_SSC_RCMR 0x10 /* Receive Clock Mode Register */ +#define AT91_SSC_CKS (3 << 0) /* Clock Selection */ +#define AT91_SSC_CKS_DIV (0 << 0) +#define AT91_SSC_CKS_CLOCK (1 << 0) +#define AT91_SSC_CKS_PIN (2 << 0) +#define AT91_SSC_CKO (7 << 2) /* Clock Output Mode Selection */ +#define AT91_SSC_CKO_NONE (0 << 2) +#define AT91_SSC_CKO_CONTINUOUS (1 << 2) +#define AT91_SSC_CKI (1 << 5) /* Clock Inversion */ +#define AT91_SSC_CKI_FALLING (0 << 5) +#define AT91_SSC_CK_RISING (1 << 5) +#define AT91_SSC_CKG (1 << 6) /* Receive Clock Gating Selection [AT91SAM9261 only] */ +#define AT91_SSC_CKG_NONE (0 << 6) +#define AT91_SSC_CKG_RFLOW (1 << 6) +#define AT91_SSC_CKG_RFHIGH (2 << 6) +#define AT91_SSC_START (0xf << 8) /* Start Selection */ +#define AT91_SSC_START_CONTINUOUS (0 << 8) +#define AT91_SSC_START_TX_RX (1 << 8) +#define AT91_SSC_START_LOW_RF (2 << 8) +#define AT91_SSC_START_HIGH_RF (3 << 8) +#define AT91_SSC_START_FALLING_RF (4 << 8) +#define AT91_SSC_START_RISING_RF (5 << 8) +#define AT91_SSC_START_LEVEL_RF (6 << 8) +#define AT91_SSC_START_EDGE_RF (7 << 8) +#define AT91_SSC_STOP (1 << 12) /* Receive Stop Selection [AT91SAM9261 only] */ +#define AT91_SSC_STTDLY (0xff << 16) /* Start Delay */ +#define AT91_SSC_PERIOD (0xff << 24) /* Period Divider Selection */ + +#define AT91_SSC_RFMR 0x14 /* Receive Frame Mode Register */ +#define AT91_SSC_DATALEN (0x1f << 0) /* Data Length */ +#define AT91_SSC_LOOP (1 << 5) /* Loop Mode */ +#define AT91_SSC_MSBF (1 << 7) /* Most Significant Bit First */ +#define AT91_SSC_DATNB (0xf << 8) /* Data Number per Frame */ +#define AT91_SSC_FSLEN (0xf << 16) /* Frame Sync Length */ +#define AT91_SSC_FSOS (7 << 20) /* Frame Sync Output Selection */ +#define AT91_SSC_FSOS_NONE (0 << 20) +#define AT91_SSC_FSOS_NEGATIVE (1 << 20) +#define AT91_SSC_FSOS_POSITIVE (2 << 20) +#define AT91_SSC_FSOS_LOW (3 << 20) +#define AT91_SSC_FSOS_HIGH (4 << 20) +#define AT91_SSC_FSOS_TOGGLE (5 << 20) +#define AT91_SSC_FSEDGE (1 << 24) /* Frame Sync Edge Detection */ +#define AT91_SSC_FSEDGE_POSITIVE (0 << 24) +#define AT91_SSC_FSEDGE_NEGATIVE (1 << 24) + +#define AT91_SSC_TCMR 0x18 /* Transmit Clock Mode Register */ +#define AT91_SSC_TFMR 0x1c /* Transmit Fram Mode Register */ +#define AT91_SSC_DATDEF (1 << 5) /* Data Default Value */ +#define AT91_SSC_FSDEN (1 << 23) /* Frame Sync Data Enable */ + +#define AT91_SSC_RHR 0x20 /* Receive Holding Register */ +#define AT91_SSC_THR 0x24 /* Transmit Holding Register */ +#define AT91_SSC_RSHR 0x30 /* Receive Sync Holding Register */ +#define AT91_SSC_TSHR 0x34 /* Transmit Sync Holding Register */ + +#define AT91_SSC_RC0R 0x38 /* Receive Compare 0 Register [AT91SAM9261 only] */ +#define AT91_SSC_RC1R 0x3c /* Receive Compare 1 Register [AT91SAM9261 only] */ + +#define AT91_SSC_SR 0x40 /* Status Register */ +#define AT91_SSC_TXRDY (1 << 0) /* Transmit Ready */ +#define AT91_SSC_TXEMPTY (1 << 1) /* Transmit Empty */ +#define AT91_SSC_ENDTX (1 << 2) /* End of Transmission */ +#define AT91_SSC_TXBUFE (1 << 3) /* Transmit Buffer Empty */ +#define AT91_SSC_RXRDY (1 << 4) /* Receive Ready */ +#define AT91_SSC_OVRUN (1 << 5) /* Receive Overrun */ +#define AT91_SSC_ENDRX (1 << 6) /* End of Reception */ +#define AT91_SSC_RXBUFF (1 << 7) /* Receive Buffer Full */ +#define AT91_SSC_CP0 (1 << 8) /* Compare 0 [AT91SAM9261 only] */ +#define AT91_SSC_CP1 (1 << 9) /* Compare 1 [AT91SAM9261 only] */ +#define AT91_SSC_TXSYN (1 << 10) /* Transmit Sync */ +#define AT91_SSC_RXSYN (1 << 11) /* Receive Sync */ +#define AT91_SSC_TXENA (1 << 16) /* Transmit Enable */ +#define AT91_SSC_RXENA (1 << 17) /* Receive Enable */ + +#define AT91_SSC_IER 0x44 /* Interrupt Enable Register */ +#define AT91_SSC_IDR 0x48 /* Interrupt Disable Register */ +#define AT91_SSC_IMR 0x4c /* Interrupt Mask Register */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_st.h b/include/asm-arm/arch-at91/at91_st.h new file mode 100644 index 000000000000..30446e2ea772 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_st.h @@ -0,0 +1,49 @@ +/* + * include/asm-arm/arch-at91/at91_st.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * System Timer (ST) - System peripherals registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_ST_H +#define AT91_ST_H + +#define AT91_ST_CR (AT91_ST + 0x00) /* Control Register */ +#define AT91_ST_WDRST (1 << 0) /* Watchdog Timer Restart */ + +#define AT91_ST_PIMR (AT91_ST + 0x04) /* Period Interval Mode Register */ +#define AT91_ST_PIV (0xffff << 0) /* Period Interval Value */ + +#define AT91_ST_WDMR (AT91_ST + 0x08) /* Watchdog Mode Register */ +#define AT91_ST_WDV (0xffff << 0) /* Watchdog Counter Value */ +#define AT91_ST_RSTEN (1 << 16) /* Reset Enable */ +#define AT91_ST_EXTEN (1 << 17) /* External Signal Assertion Enable */ + +#define AT91_ST_RTMR (AT91_ST + 0x0c) /* Real-time Mode Register */ +#define AT91_ST_RTPRES (0xffff << 0) /* Real-time Prescalar Value */ + +#define AT91_ST_SR (AT91_ST + 0x10) /* Status Register */ +#define AT91_ST_PITS (1 << 0) /* Period Interval Timer Status */ +#define AT91_ST_WDOVF (1 << 1) /* Watchdog Overflow */ +#define AT91_ST_RTTINC (1 << 2) /* Real-time Timer Increment */ +#define AT91_ST_ALMS (1 << 3) /* Alarm Status */ + +#define AT91_ST_IER (AT91_ST + 0x14) /* Interrupt Enable Register */ +#define AT91_ST_IDR (AT91_ST + 0x18) /* Interrupt Disable Register */ +#define AT91_ST_IMR (AT91_ST + 0x1c) /* Interrupt Mask Register */ + +#define AT91_ST_RTAR (AT91_ST + 0x20) /* Real-time Alarm Register */ +#define AT91_ST_ALMV (0xfffff << 0) /* Alarm Value */ + +#define AT91_ST_CRTR (AT91_ST + 0x24) /* Current Real-time Register */ +#define AT91_ST_CRTV (0xfffff << 0) /* Current Real-Time Value */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_tc.h b/include/asm-arm/arch-at91/at91_tc.h new file mode 100644 index 000000000000..b85d3faeef5c --- /dev/null +++ b/include/asm-arm/arch-at91/at91_tc.h @@ -0,0 +1,146 @@ +/* + * include/asm-arm/arch-at91/at91_tc.h + * + * Copyright (C) SAN People + * + * Timer/Counter Unit (TC) registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_TC_H +#define AT91_TC_H + +#define AT91_TC_BCR 0xc0 /* TC Block Control Register */ +#define AT91_TC_SYNC (1 << 0) /* Synchro Command */ + +#define AT91_TC_BMR 0xc4 /* TC Block Mode Register */ +#define AT91_TC_TC0XC0S (3 << 0) /* External Clock Signal 0 Selection */ +#define AT91_TC_TC0XC0S_TCLK0 (0 << 0) +#define AT91_TC_TC0XC0S_NONE (1 << 0) +#define AT91_TC_TC0XC0S_TIOA1 (2 << 0) +#define AT91_TC_TC0XC0S_TIOA2 (3 << 0) +#define AT91_TC_TC1XC1S (3 << 2) /* External Clock Signal 1 Selection */ +#define AT91_TC_TC1XC1S_TCLK1 (0 << 2) +#define AT91_TC_TC1XC1S_NONE (1 << 2) +#define AT91_TC_TC1XC1S_TIOA0 (2 << 2) +#define AT91_TC_TC1XC1S_TIOA2 (3 << 2) +#define AT91_TC_TC2XC2S (3 << 4) /* External Clock Signal 2 Selection */ +#define AT91_TC_TC2XC2S_TCLK2 (0 << 4) +#define AT91_TC_TC2XC2S_NONE (1 << 4) +#define AT91_TC_TC2XC2S_TIOA0 (2 << 4) +#define AT91_TC_TC2XC2S_TIOA1 (3 << 4) + + +#define AT91_TC_CCR 0x00 /* Channel Control Register */ +#define AT91_TC_CLKEN (1 << 0) /* Counter Clock Enable Command */ +#define AT91_TC_CLKDIS (1 << 1) /* Counter CLock Disable Command */ +#define AT91_TC_SWTRG (1 << 2) /* Software Trigger Command */ + +#define AT91_TC_CMR 0x04 /* Channel Mode Register */ +#define AT91_TC_TCCLKS (7 << 0) /* Capture/Waveform Mode: Clock Selection */ +#define AT91_TC_TIMER_CLOCK1 (0 << 0) +#define AT91_TC_TIMER_CLOCK2 (1 << 0) +#define AT91_TC_TIMER_CLOCK3 (2 << 0) +#define AT91_TC_TIMER_CLOCK4 (3 << 0) +#define AT91_TC_TIMER_CLOCK5 (4 << 0) +#define AT91_TC_XC0 (5 << 0) +#define AT91_TC_XC1 (6 << 0) +#define AT91_TC_XC2 (7 << 0) +#define AT91_TC_CLKI (1 << 3) /* Capture/Waveform Mode: Clock Invert */ +#define AT91_TC_BURST (3 << 4) /* Capture/Waveform Mode: Burst Signal Selection */ +#define AT91_TC_LDBSTOP (1 << 6) /* Capture Mode: Counter Clock Stopped with TB Loading */ +#define AT91_TC_LDBDIS (1 << 7) /* Capture Mode: Counter Clock Disable with RB Loading */ +#define AT91_TC_ETRGEDG (3 << 8) /* Capture Mode: External Trigger Edge Selection */ +#define AT91_TC_ABETRG (1 << 10) /* Capture Mode: TIOA or TIOB External Trigger Selection */ +#define AT91_TC_CPCTRG (1 << 14) /* Capture Mode: RC Compare Trigger Enable */ +#define AT91_TC_WAVE (1 << 15) /* Capture/Waveform mode */ +#define AT91_TC_LDRA (3 << 16) /* Capture Mode: RA Loading Selection */ +#define AT91_TC_LDRB (3 << 18) /* Capture Mode: RB Loading Selection */ + +#define AT91_TC_CPCSTOP (1 << 6) /* Waveform Mode: Counter Clock Stopped with RC Compare */ +#define AT91_TC_CPCDIS (1 << 7) /* Waveform Mode: Counter Clock Disable with RC Compare */ +#define AT91_TC_EEVTEDG (3 << 8) /* Waveform Mode: External Event Edge Selection */ +#define AT91_TC_EEVTEDG_NONE (0 << 8) +#define AT91_TC_EEVTEDG_RISING (1 << 8) +#define AT91_TC_EEVTEDG_FALLING (2 << 8) +#define AT91_TC_EEVTEDG_BOTH (3 << 8) +#define AT91_TC_EEVT (3 << 10) /* Waveform Mode: External Event Selection */ +#define AT91_TC_EEVT_TIOB (0 << 10) +#define AT91_TC_EEVT_XC0 (1 << 10) +#define AT91_TC_EEVT_XC1 (2 << 10) +#define AT91_TC_EEVT_XC2 (3 << 10) +#define AT91_TC_ENETRG (1 << 12) /* Waveform Mode: External Event Trigger Enable */ +#define AT91_TC_WAVESEL (3 << 13) /* Waveform Mode: Waveform Selection */ +#define AT91_TC_WAVESEL_UP (0 << 13) +#define AT91_TC_WAVESEL_UP_AUTO (2 << 13) +#define AT91_TC_WAVESEL_UPDOWN (1 << 13) +#define AT91_TC_WAVESEL_UPDOWN_AUTO (3 << 13) +#define AT91_TC_ACPA (3 << 16) /* Waveform Mode: RA Compare Effect on TIOA */ +#define AT91_TC_ACPA_NONE (0 << 16) +#define AT91_TC_ACPA_SET (1 << 16) +#define AT91_TC_ACPA_CLEAR (2 << 16) +#define AT91_TC_ACPA_TOGGLE (3 << 16) +#define AT91_TC_ACPC (3 << 18) /* Waveform Mode: RC Compre Effect on TIOA */ +#define AT91_TC_ACPC_NONE (0 << 18) +#define AT91_TC_ACPC_SET (1 << 18) +#define AT91_TC_ACPC_CLEAR (2 << 18) +#define AT91_TC_ACPC_TOGGLE (3 << 18) +#define AT91_TC_AEEVT (3 << 20) /* Waveform Mode: External Event Effect on TIOA */ +#define AT91_TC_AEEVT_NONE (0 << 20) +#define AT91_TC_AEEVT_SET (1 << 20) +#define AT91_TC_AEEVT_CLEAR (2 << 20) +#define AT91_TC_AEEVT_TOGGLE (3 << 20) +#define AT91_TC_ASWTRG (3 << 22) /* Waveform Mode: Software Trigger Effect on TIOA */ +#define AT91_TC_ASWTRG_NONE (0 << 22) +#define AT91_TC_ASWTRG_SET (1 << 22) +#define AT91_TC_ASWTRG_CLEAR (2 << 22) +#define AT91_TC_ASWTRG_TOGGLE (3 << 22) +#define AT91_TC_BCPB (3 << 24) /* Waveform Mode: RB Compare Effect on TIOB */ +#define AT91_TC_BCPB_NONE (0 << 24) +#define AT91_TC_BCPB_SET (1 << 24) +#define AT91_TC_BCPB_CLEAR (2 << 24) +#define AT91_TC_BCPB_TOGGLE (3 << 24) +#define AT91_TC_BCPC (3 << 26) /* Waveform Mode: RC Compare Effect on TIOB */ +#define AT91_TC_BCPC_NONE (0 << 26) +#define AT91_TC_BCPC_SET (1 << 26) +#define AT91_TC_BCPC_CLEAR (2 << 26) +#define AT91_TC_BCPC_TOGGLE (3 << 26) +#define AT91_TC_BEEVT (3 << 28) /* Waveform Mode: External Event Effect on TIOB */ +#define AT91_TC_BEEVT_NONE (0 << 28) +#define AT91_TC_BEEVT_SET (1 << 28) +#define AT91_TC_BEEVT_CLEAR (2 << 28) +#define AT91_TC_BEEVT_TOGGLE (3 << 28) +#define AT91_TC_BSWTRG (3 << 30) /* Waveform Mode: Software Trigger Effect on TIOB */ +#define AT91_TC_BSWTRG_NONE (0 << 30) +#define AT91_TC_BSWTRG_SET (1 << 30) +#define AT91_TC_BSWTRG_CLEAR (2 << 30) +#define AT91_TC_BSWTRG_TOGGLE (3 << 30) + +#define AT91_TC_CV 0x10 /* Counter Value */ +#define AT91_TC_RA 0x14 /* Register A */ +#define AT91_TC_RB 0x18 /* Register B */ +#define AT91_TC_RC 0x1c /* Register C */ + +#define AT91_TC_SR 0x20 /* Status Register */ +#define AT91_TC_COVFS (1 << 0) /* Counter Overflow Status */ +#define AT91_TC_LOVRS (1 << 1) /* Load Overrun Status */ +#define AT91_TC_CPAS (1 << 2) /* RA Compare Status */ +#define AT91_TC_CPBS (1 << 3) /* RB Compare Status */ +#define AT91_TC_CPCS (1 << 4) /* RC Compare Status */ +#define AT91_TC_LDRAS (1 << 5) /* RA Loading Status */ +#define AT91_TC_LDRBS (1 << 6) /* RB Loading Status */ +#define AT91_TC_ETRGS (1 << 7) /* External Trigger Status */ +#define AT91_TC_CLKSTA (1 << 16) /* Clock Enabling Status */ +#define AT91_TC_MTIOA (1 << 17) /* TIOA Mirror */ +#define AT91_TC_MTIOB (1 << 18) /* TIOB Mirror */ + +#define AT91_TC_IER 0x24 /* Interrupt Enable Register */ +#define AT91_TC_IDR 0x28 /* Interrupt Disable Register */ +#define AT91_TC_IMR 0x2c /* Interrupt Mask Register */ + +#endif diff --git a/include/asm-arm/arch-at91/at91_twi.h b/include/asm-arm/arch-at91/at91_twi.h new file mode 100644 index 000000000000..ca9a90733456 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_twi.h @@ -0,0 +1,57 @@ +/* + * include/asm-arm/arch-at91/at91_twi.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Two-wire Interface (TWI) registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_TWI_H +#define AT91_TWI_H + +#define AT91_TWI_CR 0x00 /* Control Register */ +#define AT91_TWI_START (1 << 0) /* Send a Start Condition */ +#define AT91_TWI_STOP (1 << 1) /* Send a Stop Condition */ +#define AT91_TWI_MSEN (1 << 2) /* Master Transfer Enable */ +#define AT91_TWI_MSDIS (1 << 3) /* Master Transfer Disable */ +#define AT91_TWI_SWRST (1 << 7) /* Software Reset */ + +#define AT91_TWI_MMR 0x04 /* Master Mode Register */ +#define AT91_TWI_IADRSZ (3 << 8) /* Internal Device Address Size */ +#define AT91_TWI_IADRSZ_NO (0 << 8) +#define AT91_TWI_IADRSZ_1 (1 << 8) +#define AT91_TWI_IADRSZ_2 (2 << 8) +#define AT91_TWI_IADRSZ_3 (3 << 8) +#define AT91_TWI_MREAD (1 << 12) /* Master Read Direction */ +#define AT91_TWI_DADR (0x7f << 16) /* Device Address */ + +#define AT91_TWI_IADR 0x0c /* Internal Address Register */ + +#define AT91_TWI_CWGR 0x10 /* Clock Waveform Generator Register */ +#define AT91_TWI_CLDIV (0xff << 0) /* Clock Low Divisor */ +#define AT91_TWI_CHDIV (0xff << 8) /* Clock High Divisor */ +#define AT91_TWI_CKDIV (7 << 16) /* Clock Divider */ + +#define AT91_TWI_SR 0x20 /* Status Register */ +#define AT91_TWI_TXCOMP (1 << 0) /* Transmission Complete */ +#define AT91_TWI_RXRDY (1 << 1) /* Receive Holding Register Ready */ +#define AT91_TWI_TXRDY (1 << 2) /* Transmit Holding Register Ready */ +#define AT91_TWI_OVRE (1 << 6) /* Overrun Error [AT91RM9200 only] */ +#define AT91_TWI_UNRE (1 << 7) /* Underrun Error [AT91RM9200 only] */ +#define AT91_TWI_NACK (1 << 8) /* Not Acknowledged */ + +#define AT91_TWI_IER 0x24 /* Interrupt Enable Register */ +#define AT91_TWI_IDR 0x28 /* Interrupt Disable Register */ +#define AT91_TWI_IMR 0x2c /* Interrupt Mask Register */ +#define AT91_TWI_RHR 0x30 /* Receive Holding Register */ +#define AT91_TWI_THR 0x34 /* Transmit Holding Register */ + +#endif + diff --git a/include/asm-arm/arch-at91/at91_wdt.h b/include/asm-arm/arch-at91/at91_wdt.h new file mode 100644 index 000000000000..7251a344c740 --- /dev/null +++ b/include/asm-arm/arch-at91/at91_wdt.h @@ -0,0 +1,34 @@ +/* + * include/asm-arm/arch-at91/at91_wdt.h + * + * Watchdog Timer (WDT) - System peripherals regsters. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91_WDT_H +#define AT91_WDT_H + +#define AT91_WDT_CR (AT91_WDT + 0x00) /* Watchdog Control Register */ +#define AT91_WDT_WDRSTT (1 << 0) /* Restart */ +#define AT91_WDT_KEY (0xff << 24) /* KEY Password */ + +#define AT91_WDT_MR (AT91_WDT + 0x04) /* Watchdog Mode Register */ +#define AT91_WDT_WDV (0xfff << 0) /* Counter Value */ +#define AT91_WDT_WDFIEN (1 << 12) /* Fault Interrupt Enable */ +#define AT91_WDT_WDRSTEN (1 << 13) /* Reset Processor */ +#define AT91_WDT_WDRPROC (1 << 14) /* Timer Restart */ +#define AT91_WDT_WDDIS (1 << 15) /* Watchdog Disable */ +#define AT91_WDT_WDD (0xfff << 16) /* Delta Value */ +#define AT91_WDT_WDDBGHLT (1 << 28) /* Debug Halt */ +#define AT91_WDT_WDIDLEHLT (1 << 29) /* Idle Halt */ + +#define AT91_WDT_SR (AT91_WDT + 0x08) /* Watchdog Status Register */ +#define AT91_WDT_WDUNF (1 << 0) /* Watchdog Underflow */ +#define AT91_WDT_WDERR (1 << 1) /* Watchdog Error */ + +#endif diff --git a/include/asm-arm/arch-at91/at91rm9200.h b/include/asm-arm/arch-at91/at91rm9200.h new file mode 100644 index 000000000000..a12ac8ab2ad0 --- /dev/null +++ b/include/asm-arm/arch-at91/at91rm9200.h @@ -0,0 +1,291 @@ +/* + * include/asm-arm/arch-at91/at91rm9200.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Common definitions. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91RM9200_H +#define AT91RM9200_H + +/* + * Peripheral identifiers/interrupts. + */ +#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ +#define AT91_ID_SYS 1 /* System Peripheral */ +#define AT91RM9200_ID_PIOA 2 /* Parallel IO Controller A */ +#define AT91RM9200_ID_PIOB 3 /* Parallel IO Controller B */ +#define AT91RM9200_ID_PIOC 4 /* Parallel IO Controller C */ +#define AT91RM9200_ID_PIOD 5 /* Parallel IO Controller D */ +#define AT91RM9200_ID_US0 6 /* USART 0 */ +#define AT91RM9200_ID_US1 7 /* USART 1 */ +#define AT91RM9200_ID_US2 8 /* USART 2 */ +#define AT91RM9200_ID_US3 9 /* USART 3 */ +#define AT91RM9200_ID_MCI 10 /* Multimedia Card Interface */ +#define AT91RM9200_ID_UDP 11 /* USB Device Port */ +#define AT91RM9200_ID_TWI 12 /* Two-Wire Interface */ +#define AT91RM9200_ID_SPI 13 /* Serial Peripheral Interface */ +#define AT91RM9200_ID_SSC0 14 /* Serial Synchronous Controller 0 */ +#define AT91RM9200_ID_SSC1 15 /* Serial Synchronous Controller 1 */ +#define AT91RM9200_ID_SSC2 16 /* Serial Synchronous Controller 2 */ +#define AT91RM9200_ID_TC0 17 /* Timer Counter 0 */ +#define AT91RM9200_ID_TC1 18 /* Timer Counter 1 */ +#define AT91RM9200_ID_TC2 19 /* Timer Counter 2 */ +#define AT91RM9200_ID_TC3 20 /* Timer Counter 3 */ +#define AT91RM9200_ID_TC4 21 /* Timer Counter 4 */ +#define AT91RM9200_ID_TC5 22 /* Timer Counter 5 */ +#define AT91RM9200_ID_UHP 23 /* USB Host port */ +#define AT91RM9200_ID_EMAC 24 /* Ethernet MAC */ +#define AT91RM9200_ID_IRQ0 25 /* Advanced Interrupt Controller (IRQ0) */ +#define AT91RM9200_ID_IRQ1 26 /* Advanced Interrupt Controller (IRQ1) */ +#define AT91RM9200_ID_IRQ2 27 /* Advanced Interrupt Controller (IRQ2) */ +#define AT91RM9200_ID_IRQ3 28 /* Advanced Interrupt Controller (IRQ3) */ +#define AT91RM9200_ID_IRQ4 29 /* Advanced Interrupt Controller (IRQ4) */ +#define AT91RM9200_ID_IRQ5 30 /* Advanced Interrupt Controller (IRQ5) */ +#define AT91RM9200_ID_IRQ6 31 /* Advanced Interrupt Controller (IRQ6) */ + + +/* + * Peripheral physical base addresses. + */ +#define AT91RM9200_BASE_TCB0 0xfffa0000 +#define AT91RM9200_BASE_TC0 0xfffa0000 +#define AT91RM9200_BASE_TC1 0xfffa0040 +#define AT91RM9200_BASE_TC2 0xfffa0080 +#define AT91RM9200_BASE_TCB1 0xfffa4000 +#define AT91RM9200_BASE_TC3 0xfffa4000 +#define AT91RM9200_BASE_TC4 0xfffa4040 +#define AT91RM9200_BASE_TC5 0xfffa4080 +#define AT91RM9200_BASE_UDP 0xfffb0000 +#define AT91RM9200_BASE_MCI 0xfffb4000 +#define AT91RM9200_BASE_TWI 0xfffb8000 +#define AT91RM9200_BASE_EMAC 0xfffbc000 +#define AT91RM9200_BASE_US0 0xfffc0000 +#define AT91RM9200_BASE_US1 0xfffc4000 +#define AT91RM9200_BASE_US2 0xfffc8000 +#define AT91RM9200_BASE_US3 0xfffcc000 +#define AT91RM9200_BASE_SSC0 0xfffd0000 +#define AT91RM9200_BASE_SSC1 0xfffd4000 +#define AT91RM9200_BASE_SSC2 0xfffd8000 +#define AT91RM9200_BASE_SPI 0xfffe0000 +#define AT91_BASE_SYS 0xfffff000 + + +/* + * System Peripherals (offset from AT91_BASE_SYS) + */ +#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */ +#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) /* Debug Unit */ +#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) /* PIO Controller A */ +#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) /* PIO Controller B */ +#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) /* PIO Controller C */ +#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS) /* PIO Controller D */ +#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */ +#define AT91_ST (0xfffffd00 - AT91_BASE_SYS) /* System Timer */ +#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) /* Real-Time Clock */ +#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */ + +#define AT91_MATRIX 0 /* not supported */ + +/* + * Internal Memory. + */ +#define AT91RM9200_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91RM9200_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ + +#define AT91RM9200_SRAM_BASE 0x00200000 /* Internal SRAM base address */ +#define AT91RM9200_SRAM_SIZE SZ_16K /* Internal SRAM size (16Kb) */ + +#define AT91RM9200_UHP_BASE 0x00300000 /* USB Host controller */ + + +#if 0 +/* + * PIO pin definitions (peripheral A/B multiplexing). + */ +#define AT91_PA0_MISO (1 << 0) /* A: SPI Master-In Slave-Out */ +#define AT91_PA0_PCK3 (1 << 0) /* B: PMC Programmable Clock Output 3 */ +#define AT91_PA1_MOSI (1 << 1) /* A: SPI Master-Out Slave-In */ +#define AT91_PA1_PCK0 (1 << 1) /* B: PMC Programmable Clock Output 0 */ +#define AT91_PA2_SPCK (1 << 2) /* A: SPI Serial Clock */ +#define AT91_PA2_IRQ4 (1 << 2) /* B: External Interrupt 4 */ +#define AT91_PA3_NPCS0 (1 << 3) /* A: SPI Peripheral Chip Select 0 */ +#define AT91_PA3_IRQ5 (1 << 3) /* B: External Interrupt 5 */ +#define AT91_PA4_NPCS1 (1 << 4) /* A: SPI Peripheral Chip Select 1 */ +#define AT91_PA4_PCK1 (1 << 4) /* B: PMC Programmable Clock Output 1 */ +#define AT91_PA5_NPCS2 (1 << 5) /* A: SPI Peripheral Chip Select 2 */ +#define AT91_PA5_TXD3 (1 << 5) /* B: USART Transmit Data 3 */ +#define AT91_PA6_NPCS3 (1 << 6) /* A: SPI Peripheral Chip Select 3 */ +#define AT91_PA6_RXD3 (1 << 6) /* B: USART Receive Data 3 */ +#define AT91_PA7_ETXCK_EREFCK (1 << 7) /* A: Ethernet Reference Clock / Transmit Clock */ +#define AT91_PA7_PCK2 (1 << 7) /* B: PMC Programmable Clock Output 2 */ +#define AT91_PA8_ETXEN (1 << 8) /* A: Ethernet Transmit Enable */ +#define AT91_PA8_MCCDB (1 << 8) /* B: MMC Multimedia Card B Command */ +#define AT91_PA9_ETX0 (1 << 9) /* A: Ethernet Transmit Data 0 */ +#define AT91_PA9_MCDB0 (1 << 9) /* B: MMC Multimedia Card B Data 0 */ +#define AT91_PA10_ETX1 (1 << 10) /* A: Ethernet Transmit Data 1 */ +#define AT91_PA10_MCDB1 (1 << 10) /* B: MMC Multimedia Card B Data 1 */ +#define AT91_PA11_ECRS_ECRSDV (1 << 11) /* A: Ethernet Carrier Sense / Data Valid */ +#define AT91_PA11_MCDB2 (1 << 11) /* B: MMC Multimedia Card B Data 2 */ +#define AT91_PA12_ERX0 (1 << 12) /* A: Ethernet Receive Data 0 */ +#define AT91_PA12_MCDB3 (1 << 12) /* B: MMC Multimedia Card B Data 3 */ +#define AT91_PA13_ERX1 (1 << 13) /* A: Ethernet Receive Data 1 */ +#define AT91_PA13_TCLK0 (1 << 13) /* B: TC External Clock Input 0 */ +#define AT91_PA14_ERXER (1 << 14) /* A: Ethernet Receive Error */ +#define AT91_PA14_TCLK1 (1 << 14) /* B: TC External Clock Input 1 */ +#define AT91_PA15_EMDC (1 << 15) /* A: Ethernet Management Data Clock */ +#define AT91_PA15_TCLK2 (1 << 15) /* B: TC External Clock Input 2 */ +#define AT91_PA16_EMDIO (1 << 16) /* A: Ethernet Management Data I/O */ +#define AT91_PA16_IRQ6 (1 << 16) /* B: External Interrupt 6 */ +#define AT91_PA17_TXD0 (1 << 17) /* A: USART Transmit Data 0 */ +#define AT91_PA17_TIOA0 (1 << 17) /* B: TC I/O Line A 0 */ +#define AT91_PA18_RXD0 (1 << 18) /* A: USART Receive Data 0 */ +#define AT91_PA18_TIOB0 (1 << 18) /* B: TC I/O Line B 0 */ +#define AT91_PA19_SCK0 (1 << 19) /* A: USART Serial Clock 0 */ +#define AT91_PA19_TIOA1 (1 << 19) /* B: TC I/O Line A 1 */ +#define AT91_PA20_CTS0 (1 << 20) /* A: USART Clear To Send 0 */ +#define AT91_PA20_TIOB1 (1 << 20) /* B: TC I/O Line B 1 */ +#define AT91_PA21_RTS0 (1 << 21) /* A: USART Ready To Send 0 */ +#define AT91_PA21_TIOA2 (1 << 21) /* B: TC I/O Line A 2 */ +#define AT91_PA22_RXD2 (1 << 22) /* A: USART Receive Data 2 */ +#define AT91_PA22_TIOB2 (1 << 22) /* B: TC I/O Line B 2 */ +#define AT91_PA23_TXD2 (1 << 23) /* A: USART Transmit Data 2 */ +#define AT91_PA23_IRQ3 (1 << 23) /* B: External Interrupt 3 */ +#define AT91_PA24_SCK2 (1 << 24) /* A: USART Serial Clock 2 */ +#define AT91_PA24_PCK1 (1 << 24) /* B: PMC Programmable Clock Output 1 */ +#define AT91_PA25_TWD (1 << 25) /* A: TWI Two-wire Serial Data */ +#define AT91_PA25_IRQ2 (1 << 25) /* B: External Interrupt 2 */ +#define AT91_PA26_TWCK (1 << 26) /* A: TWI Two-wire Serial Clock */ +#define AT91_PA26_IRQ1 (1 << 26) /* B: External Interrupt 1 */ +#define AT91_PA27_MCCK (1 << 27) /* A: MMC Multimedia Card Clock */ +#define AT91_PA27_TCLK3 (1 << 27) /* B: TC External Clock Input 3 */ +#define AT91_PA28_MCCDA (1 << 28) /* A: MMC Multimedia Card A Command */ +#define AT91_PA28_TCLK4 (1 << 28) /* B: TC External Clock Input 4 */ +#define AT91_PA29_MCDA0 (1 << 29) /* A: MMC Multimedia Card A Data 0 */ +#define AT91_PA29_TCLK5 (1 << 29) /* B: TC External Clock Input 5 */ +#define AT91_PA30_DRXD (1 << 30) /* A: DBGU Receive Data */ +#define AT91_PA30_CTS2 (1 << 30) /* B: USART Clear To Send 2 */ +#define AT91_PA31_DTXD (1 << 31) /* A: DBGU Transmit Data */ +#define AT91_PA31_RTS2 (1 << 31) /* B: USART Ready To Send 2 */ + +#define AT91_PB0_TF0 (1 << 0) /* A: SSC Transmit Frame Sync 0 */ +#define AT91_PB0_RTS3 (1 << 0) /* B: USART Ready To Send 3 */ +#define AT91_PB1_TK0 (1 << 1) /* A: SSC Transmit Clock 0 */ +#define AT91_PB1_CTS3 (1 << 1) /* B: USART Clear To Send 3 */ +#define AT91_PB2_TD0 (1 << 2) /* A: SSC Transmit Data 0 */ +#define AT91_PB2_SCK3 (1 << 2) /* B: USART Serial Clock 3 */ +#define AT91_PB3_RD0 (1 << 3) /* A: SSC Receive Data 0 */ +#define AT91_PB3_MCDA1 (1 << 3) /* B: MMC Multimedia Card A Data 1 */ +#define AT91_PB4_RK0 (1 << 4) /* A: SSC Receive Clock 0 */ +#define AT91_PB4_MCDA2 (1 << 4) /* B: MMC Multimedia Card A Data 2 */ +#define AT91_PB5_RF0 (1 << 5) /* A: SSC Receive Frame Sync 0 */ +#define AT91_PB5_MCDA3 (1 << 5) /* B: MMC Multimedia Card A Data 3 */ +#define AT91_PB6_TF1 (1 << 6) /* A: SSC Transmit Frame Sync 1 */ +#define AT91_PB6_TIOA3 (1 << 6) /* B: TC I/O Line A 3 */ +#define AT91_PB7_TK1 (1 << 7) /* A: SSC Transmit Clock 1 */ +#define AT91_PB7_TIOB3 (1 << 7) /* B: TC I/O Line B 3 */ +#define AT91_PB8_TD1 (1 << 8) /* A: SSC Transmit Data 1 */ +#define AT91_PB8_TIOA4 (1 << 8) /* B: TC I/O Line A 4 */ +#define AT91_PB9_RD1 (1 << 9) /* A: SSC Receive Data 1 */ +#define AT91_PB9_TIOB4 (1 << 9) /* B: TC I/O Line B 4 */ +#define AT91_PB10_RK1 (1 << 10) /* A: SSC Receive Clock 1 */ +#define AT91_PB10_TIOA5 (1 << 10) /* B: TC I/O Line A 5 */ +#define AT91_PB11_RF1 (1 << 11) /* A: SSC Receive Frame Sync 1 */ +#define AT91_PB11_TIOB5 (1 << 11) /* B: TC I/O Line B 5 */ +#define AT91_PB12_TF2 (1 << 12) /* A: SSC Transmit Frame Sync 2 */ +#define AT91_PB12_ETX2 (1 << 12) /* B: Ethernet Transmit Data 2 */ +#define AT91_PB13_TK2 (1 << 13) /* A: SSC Transmit Clock 3 */ +#define AT91_PB13_ETX3 (1 << 13) /* B: Ethernet Transmit Data 3 */ +#define AT91_PB14_TD2 (1 << 14) /* A: SSC Transmit Data 2 */ +#define AT91_PB14_ETXER (1 << 14) /* B: Ethernet Transmit Coding Error */ +#define AT91_PB15_RD2 (1 << 15) /* A: SSC Receive Data 2 */ +#define AT91_PB15_ERX2 (1 << 15) /* B: Ethernet Receive Data 2 */ +#define AT91_PB16_RK2 (1 << 16) /* A: SSC Receive Clock 2 */ +#define AT91_PB16_ERX3 (1 << 16) /* B: Ethernet Receive Data 3 */ +#define AT91_PB17_RF2 (1 << 17) /* A: SSC Receive Frame Sync 2 */ +#define AT91_PB17_ERXDV (1 << 17) /* B: Ethernet Receive Data Valid */ +#define AT91_PB18_RI1 (1 << 18) /* A: USART Ring Indicator 1 */ +#define AT91_PB18_ECOL (1 << 18) /* B: Ethernet Collision Detected */ +#define AT91_PB19_DTR1 (1 << 19) /* A: USART Data Terminal Ready 1 */ +#define AT91_PB19_ERXCK (1 << 19) /* B: Ethernet Receive Clock */ +#define AT91_PB20_TXD1 (1 << 20) /* A: USART Transmit Data 1 */ +#define AT91_PB21_RXD1 (1 << 21) /* A: USART Receive Data 1 */ +#define AT91_PB22_SCK1 (1 << 22) /* A: USART Serial Clock 1 */ +#define AT91_PB23_DCD1 (1 << 23) /* A: USART Data Carrier Detect 1 */ +#define AT91_PB24_CTS1 (1 << 24) /* A: USART Clear To Send 1 */ +#define AT91_PB25_DSR1 (1 << 25) /* A: USART Data Set Ready 1 */ +#define AT91_PB25_EF100 (1 << 25) /* B: Ethernet Force 100 Mbit */ +#define AT91_PB26_RTS1 (1 << 26) /* A: USART Ready To Send 1 */ +#define AT91_PB27_PCK0 (1 << 27) /* B: PMC Programmable Clock Output 0 */ +#define AT91_PB28_FIQ (1 << 28) /* A: Fast Interrupt */ +#define AT91_PB29_IRQ0 (1 << 29) /* A: External Interrupt 0 */ + +#define AT91_PC0_BFCK (1 << 0) /* A: Burst Flash Clock */ +#define AT91_PC1_BFRDY_SMOE (1 << 1) /* A: Burst Flash Ready / SmartMedia Output Enable */ +#define AT91_PC2_BFAVD (1 << 2) /* A: Burst Flash Address Valid */ +#define AT91_PC3_BFBAA_SMWE (1 << 3) /* A: Burst Flash Address Advance / SmartMedia Write Enable */ +#define AT91_PC4_BFOE (1 << 4) /* A: Burst Flash Output Enable */ +#define AT91_PC5_BFWE (1 << 5) /* A: Burst Flash Write Enable */ +#define AT91_PC6_NWAIT (1 << 6) /* A: SMC Wait Signal */ +#define AT91_PC7_A23 (1 << 7) /* A: Address Bus 23 */ +#define AT91_PC8_A24 (1 << 8) /* A: Address Bus 24 */ +#define AT91_PC9_A25_CFRNW (1 << 9) /* A: Address Bus 25 / Compact Flash Read Not Write */ +#define AT91_PC10_NCS4_CFCS (1 << 10) /* A: SMC Chip Select 4 / Compact Flash Chip Select */ +#define AT91_PC11_NCS5_CFCE1 (1 << 11) /* A: SMC Chip Select 5 / Compact Flash Chip Enable 1 */ +#define AT91_PC12_NCS6_CFCE2 (1 << 12) /* A: SMC Chip Select 6 / Compact Flash Chip Enable 2 */ +#define AT91_PC13_NCS7 (1 << 13) /* A: Chip Select 7 */ + +#define AT91_PD0_ETX0 (1 << 0) /* A: Ethernet Transmit Data 0 */ +#define AT91_PD1_ETX1 (1 << 1) /* A: Ethernet Transmit Data 1 */ +#define AT91_PD2_ETX2 (1 << 2) /* A: Ethernet Transmit Data 2 */ +#define AT91_PD3_ETX3 (1 << 3) /* A: Ethernet Transmit Data 3 */ +#define AT91_PD4_ETXEN (1 << 4) /* A: Ethernet Transmit Enable */ +#define AT91_PD5_ETXER (1 << 5) /* A: Ethernet Transmit Coding Error */ +#define AT91_PD6_DTXD (1 << 6) /* A: DBGU Transmit Data */ +#define AT91_PD7_PCK0 (1 << 7) /* A: PMC Programmable Clock Output 0 */ +#define AT91_PD7_TSYNC (1 << 7) /* B: ETM Trace Synchronization Signal */ +#define AT91_PD8_PCK1 (1 << 8) /* A: PMC Programmable Clock Output 1 */ +#define AT91_PD8_TCLK (1 << 8) /* B: ETM Trace Clock */ +#define AT91_PD9_PCK2 (1 << 9) /* A: PMC Programmable Clock Output 2 */ +#define AT91_PD9_TPS0 (1 << 9) /* B: ETM Trace ARM Pipeline Status 0 */ +#define AT91_PD10_PCK3 (1 << 10) /* A: PMC Programmable Clock Output 3 */ +#define AT91_PD10_TPS1 (1 << 10) /* B: ETM Trace ARM Pipeline Status 1 */ +#define AT91_PD11_TPS2 (1 << 11) /* B: ETM Trace ARM Pipeline Status 2 */ +#define AT91_PD12_TPK0 (1 << 12) /* B: ETM Trace Packet Port 0 */ +#define AT91_PD13_TPK1 (1 << 13) /* B: ETM Trace Packet Port 1 */ +#define AT91_PD14_TPK2 (1 << 14) /* B: ETM Trace Packet Port 2 */ +#define AT91_PD15_TD0 (1 << 15) /* A: SSC Transmit Data 0 */ +#define AT91_PD15_TPK3 (1 << 15) /* B: ETM Trace Packet Port 3 */ +#define AT91_PD16_TD1 (1 << 16) /* A: SSC Transmit Data 1 */ +#define AT91_PD16_TPK4 (1 << 16) /* B: ETM Trace Packet Port 4 */ +#define AT91_PD17_TD2 (1 << 17) /* A: SSC Transmit Data 2 */ +#define AT91_PD17_TPK5 (1 << 17) /* B: ETM Trace Packet Port 5 */ +#define AT91_PD18_NPCS1 (1 << 18) /* A: SPI Peripheral Chip Select 1 */ +#define AT91_PD18_TPK6 (1 << 18) /* B: ETM Trace Packet Port 6 */ +#define AT91_PD19_NPCS2 (1 << 19) /* A: SPI Peripheral Chip Select 2 */ +#define AT91_PD19_TPK7 (1 << 19) /* B: ETM Trace Packet Port 7 */ +#define AT91_PD20_NPCS3 (1 << 20) /* A: SPI Peripheral Chip Select 3 */ +#define AT91_PD20_TPK8 (1 << 20) /* B: ETM Trace Packet Port 8 */ +#define AT91_PD21_RTS0 (1 << 21) /* A: USART Ready To Send 0 */ +#define AT91_PD21_TPK9 (1 << 21) /* B: ETM Trace Packet Port 9 */ +#define AT91_PD22_RTS1 (1 << 22) /* A: USART Ready To Send 1 */ +#define AT91_PD22_TPK10 (1 << 22) /* B: ETM Trace Packet Port 10 */ +#define AT91_PD23_RTS2 (1 << 23) /* A: USART Ready To Send 2 */ +#define AT91_PD23_TPK11 (1 << 23) /* B: ETM Trace Packet Port 11 */ +#define AT91_PD24_RTS3 (1 << 24) /* A: USART Ready To Send 3 */ +#define AT91_PD24_TPK12 (1 << 24) /* B: ETM Trace Packet Port 12 */ +#define AT91_PD25_DTR1 (1 << 25) /* A: USART Data Terminal Ready 1 */ +#define AT91_PD25_TPK13 (1 << 25) /* B: ETM Trace Packet Port 13 */ +#define AT91_PD26_TPK14 (1 << 26) /* B: ETM Trace Packet Port 14 */ +#define AT91_PD27_TPK15 (1 << 27) /* B: ETM Trace Packet Port 15 */ +#endif + +#endif diff --git a/include/asm-arm/arch-at91/at91rm9200_emac.h b/include/asm-arm/arch-at91/at91rm9200_emac.h new file mode 100644 index 000000000000..0c417af5fe7f --- /dev/null +++ b/include/asm-arm/arch-at91/at91rm9200_emac.h @@ -0,0 +1,138 @@ +/* + * include/asm-arm/arch-at91/at91rm9200_emac.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Ethernet MAC registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91RM9200_EMAC_H +#define AT91RM9200_EMAC_H + +#define AT91_EMAC_CTL 0x00 /* Control Register */ +#define AT91_EMAC_LB (1 << 0) /* Loopback */ +#define AT91_EMAC_LBL (1 << 1) /* Loopback Local */ +#define AT91_EMAC_RE (1 << 2) /* Receive Enable */ +#define AT91_EMAC_TE (1 << 3) /* Transmit Enable */ +#define AT91_EMAC_MPE (1 << 4) /* Management Port Enable */ +#define AT91_EMAC_CSR (1 << 5) /* Clear Statistics Registers */ +#define AT91_EMAC_INCSTAT (1 << 6) /* Increment Statistics Registers */ +#define AT91_EMAC_WES (1 << 7) /* Write Enable for Statistics Registers */ +#define AT91_EMAC_BP (1 << 8) /* Back Pressure */ + +#define AT91_EMAC_CFG 0x04 /* Configuration Register */ +#define AT91_EMAC_SPD (1 << 0) /* Speed */ +#define AT91_EMAC_FD (1 << 1) /* Full Duplex */ +#define AT91_EMAC_BR (1 << 2) /* Bit Rate */ +#define AT91_EMAC_CAF (1 << 4) /* Copy All Frames */ +#define AT91_EMAC_NBC (1 << 5) /* No Broadcast */ +#define AT91_EMAC_MTI (1 << 6) /* Multicast Hash Enable */ +#define AT91_EMAC_UNI (1 << 7) /* Unicast Hash Enable */ +#define AT91_EMAC_BIG (1 << 8) /* Receive 1522 Bytes */ +#define AT91_EMAC_EAE (1 << 9) /* External Address Match Enable */ +#define AT91_EMAC_CLK (3 << 10) /* MDC Clock Divisor */ +#define AT91_EMAC_CLK_DIV8 (0 << 10) +#define AT91_EMAC_CLK_DIV16 (1 << 10) +#define AT91_EMAC_CLK_DIV32 (2 << 10) +#define AT91_EMAC_CLK_DIV64 (3 << 10) +#define AT91_EMAC_RTY (1 << 12) /* Retry Test */ +#define AT91_EMAC_RMII (1 << 13) /* Reduce MII (RMII) */ + +#define AT91_EMAC_SR 0x08 /* Status Register */ +#define AT91_EMAC_SR_LINK (1 << 0) /* Link */ +#define AT91_EMAC_SR_MDIO (1 << 1) /* MDIO pin */ +#define AT91_EMAC_SR_IDLE (1 << 2) /* PHY idle */ + +#define AT91_EMAC_TAR 0x0c /* Transmit Address Register */ + +#define AT91_EMAC_TCR 0x10 /* Transmit Control Register */ +#define AT91_EMAC_LEN (0x7ff << 0) /* Transmit Frame Length */ +#define AT91_EMAC_NCRC (1 << 15) /* No CRC */ + +#define AT91_EMAC_TSR 0x14 /* Transmit Status Register */ +#define AT91_EMAC_TSR_OVR (1 << 0) /* Transmit Buffer Overrun */ +#define AT91_EMAC_TSR_COL (1 << 1) /* Collision Occurred */ +#define AT91_EMAC_TSR_RLE (1 << 2) /* Retry Limit Exceeded */ +#define AT91_EMAC_TSR_IDLE (1 << 3) /* Transmitter Idle */ +#define AT91_EMAC_TSR_BNQ (1 << 4) /* Transmit Buffer not Queued */ +#define AT91_EMAC_TSR_COMP (1 << 5) /* Transmit Complete */ +#define AT91_EMAC_TSR_UND (1 << 6) /* Transmit Underrun */ + +#define AT91_EMAC_RBQP 0x18 /* Receive Buffer Queue Pointer */ + +#define AT91_EMAC_RSR 0x20 /* Receive Status Register */ +#define AT91_EMAC_RSR_BNA (1 << 0) /* Buffer Not Available */ +#define AT91_EMAC_RSR_REC (1 << 1) /* Frame Received */ +#define AT91_EMAC_RSR_OVR (1 << 2) /* RX Overrun */ + +#define AT91_EMAC_ISR 0x24 /* Interrupt Status Register */ +#define AT91_EMAC_DONE (1 << 0) /* Management Done */ +#define AT91_EMAC_RCOM (1 << 1) /* Receive Complete */ +#define AT91_EMAC_RBNA (1 << 2) /* Receive Buffer Not Available */ +#define AT91_EMAC_TOVR (1 << 3) /* Transmit Buffer Overrun */ +#define AT91_EMAC_TUND (1 << 4) /* Transmit Buffer Underrun */ +#define AT91_EMAC_RTRY (1 << 5) /* Retry Limit */ +#define AT91_EMAC_TBRE (1 << 6) /* Transmit Buffer Register Empty */ +#define AT91_EMAC_TCOM (1 << 7) /* Transmit Complete */ +#define AT91_EMAC_TIDLE (1 << 8) /* Transmit Idle */ +#define AT91_EMAC_LINK (1 << 9) /* Link */ +#define AT91_EMAC_ROVR (1 << 10) /* RX Overrun */ +#define AT91_EMAC_ABT (1 << 11) /* Abort */ + +#define AT91_EMAC_IER 0x28 /* Interrupt Enable Register */ +#define AT91_EMAC_IDR 0x2c /* Interrupt Disable Register */ +#define AT91_EMAC_IMR 0x30 /* Interrupt Mask Register */ + +#define AT91_EMAC_MAN 0x34 /* PHY Maintenance Register */ +#define AT91_EMAC_DATA (0xffff << 0) /* MDIO Data */ +#define AT91_EMAC_REGA (0x1f << 18) /* MDIO Register */ +#define AT91_EMAC_PHYA (0x1f << 23) /* MDIO PHY Address */ +#define AT91_EMAC_RW (3 << 28) /* Read/Write operation */ +#define AT91_EMAC_RW_W (1 << 28) +#define AT91_EMAC_RW_R (2 << 28) +#define AT91_EMAC_MAN_802_3 0x40020000 /* IEEE 802.3 value */ + +/* + * Statistics Registers. + */ +#define AT91_EMAC_FRA 0x40 /* Frames Transmitted OK */ +#define AT91_EMAC_SCOL 0x44 /* Single Collision Frame */ +#define AT91_EMAC_MCOL 0x48 /* Multiple Collision Frame */ +#define AT91_EMAC_OK 0x4c /* Frames Received OK */ +#define AT91_EMAC_SEQE 0x50 /* Frame Check Sequence Error */ +#define AT91_EMAC_ALE 0x54 /* Alignmemt Error */ +#define AT91_EMAC_DTE 0x58 /* Deffered Transmission Frame */ +#define AT91_EMAC_LCOL 0x5c /* Late Collision */ +#define AT91_EMAC_ECOL 0x60 /* Excessive Collision */ +#define AT91_EMAC_TUE 0x64 /* Transmit Underrun Error */ +#define AT91_EMAC_CSE 0x68 /* Carrier Sense Error */ +#define AT91_EMAC_DRFC 0x6c /* Discard RX Frame */ +#define AT91_EMAC_ROV 0x70 /* Receive Overrun */ +#define AT91_EMAC_CDE 0x74 /* Code Error */ +#define AT91_EMAC_ELR 0x78 /* Excessive Length Error */ +#define AT91_EMAC_RJB 0x7c /* Receive Jabber */ +#define AT91_EMAC_USF 0x80 /* Undersize Frame */ +#define AT91_EMAC_SQEE 0x84 /* SQE Test Error */ + +/* + * Address Registers. + */ +#define AT91_EMAC_HSL 0x90 /* Hash Address Low [31:0] */ +#define AT91_EMAC_HSH 0x94 /* Hash Address High [63:32] */ +#define AT91_EMAC_SA1L 0x98 /* Specific Address 1 Low, bytes 0-3 */ +#define AT91_EMAC_SA1H 0x9c /* Specific Address 1 High, bytes 4-5 */ +#define AT91_EMAC_SA2L 0xa0 /* Specific Address 2 Low, bytes 0-3 */ +#define AT91_EMAC_SA2H 0xa4 /* Specific Address 2 High, bytes 4-5 */ +#define AT91_EMAC_SA3L 0xa8 /* Specific Address 3 Low, bytes 0-3 */ +#define AT91_EMAC_SA3H 0xac /* Specific Address 3 High, bytes 4-5 */ +#define AT91_EMAC_SA4L 0xb0 /* Specific Address 4 Low, bytes 0-3 */ +#define AT91_EMAC_SA4H 0xb4 /* Specific Address 4 High, bytes 4-5 */ + +#endif diff --git a/include/asm-arm/arch-at91/at91rm9200_mc.h b/include/asm-arm/arch-at91/at91rm9200_mc.h new file mode 100644 index 000000000000..24d012939cc4 --- /dev/null +++ b/include/asm-arm/arch-at91/at91rm9200_mc.h @@ -0,0 +1,160 @@ +/* + * include/asm-arm/arch-at91/at91rm9200_mc.h + * + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) SAN People + * + * Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals registers. + * Based on AT91RM9200 datasheet revision E. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91RM9200_MC_H +#define AT91RM9200_MC_H + +/* Memory Controller */ +#define AT91_MC_RCR (AT91_MC + 0x00) /* MC Remap Control Register */ +#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */ + +#define AT91_MC_ASR (AT91_MC + 0x04) /* MC Abort Status Register */ +#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */ +#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */ +#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */ +#define AT91_MC_ABTSZ_BYTE (0 << 8) +#define AT91_MC_ABTSZ_HALFWORD (1 << 8) +#define AT91_MC_ABTSZ_WORD (2 << 8) +#define AT91_MC_ABTTYP (3 << 10) /* Abort Type Status */ +#define AT91_MC_ABTTYP_DATAREAD (0 << 10) +#define AT91_MC_ABTTYP_DATAWRITE (1 << 10) +#define AT91_MC_ABTTYP_FETCH (2 << 10) +#define AT91_MC_MST0 (1 << 16) /* ARM920T Abort Source */ +#define AT91_MC_MST1 (1 << 17) /* PDC Abort Source */ +#define AT91_MC_MST2 (1 << 18) /* UHP Abort Source */ +#define AT91_MC_MST3 (1 << 19) /* EMAC Abort Source */ +#define AT91_MC_SVMST0 (1 << 24) /* Saved ARM920T Abort Source */ +#define AT91_MC_SVMST1 (1 << 25) /* Saved PDC Abort Source */ +#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */ +#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */ + +#define AT91_MC_AASR (AT91_MC + 0x08) /* MC Abort Address Status Register */ + +#define AT91_MC_MPR (AT91_MC + 0x0c) /* MC Master Priority Register */ +#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */ +#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */ +#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */ +#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */ + +/* External Bus Interface (EBI) registers */ +#define AT91_EBI_CSA (AT91_MC + 0x60) /* Chip Select Assignment Register */ +#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */ +#define AT91_EBI_CS0A_SMC (0 << 0) +#define AT91_EBI_CS0A_BFC (1 << 0) +#define AT91_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ +#define AT91_EBI_CS1A_SMC (0 << 1) +#define AT91_EBI_CS1A_SDRAMC (1 << 1) +#define AT91_EBI_CS3A (1 << 3) /* Chip Select 2 Assignment */ +#define AT91_EBI_CS3A_SMC (0 << 3) +#define AT91_EBI_CS3A_SMC_SMARTMEDIA (1 << 3) +#define AT91_EBI_CS4A (1 << 4) /* Chip Select 3 Assignment */ +#define AT91_EBI_CS4A_SMC (0 << 4) +#define AT91_EBI_CS4A_SMC_COMPACTFLASH (1 << 4) +#define AT91_EBI_CFGR (AT91_MC + 0x64) /* Configuration Register */ +#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */ + +/* Static Memory Controller (SMC) registers */ +#define AT91_SMC_CSR(n) (AT91_MC + 0x70 + ((n) * 4))/* SMC Chip Select Register */ +#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */ +#define AT91_SMC_NWS_(x) ((x) << 0) +#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */ +#define AT91_SMC_TDF (0xf << 8) /* Data Float Time */ +#define AT91_SMC_TDF_(x) ((x) << 8) +#define AT91_SMC_BAT (1 << 12) /* Byte Access Type */ +#define AT91_SMC_DBW (3 << 13) /* Data Bus Width */ +#define AT91_SMC_DBW_16 (1 << 13) +#define AT91_SMC_DBW_8 (2 << 13) +#define AT91_SMC_DPR (1 << 15) /* Data Read Protocol */ +#define AT91_SMC_ACSS (3 << 16) /* Address to Chip Select Setup */ +#define AT91_SMC_ACSS_STD (0 << 16) +#define AT91_SMC_ACSS_1 (1 << 16) +#define AT91_SMC_ACSS_2 (2 << 16) +#define AT91_SMC_ACSS_3 (3 << 16) +#define AT91_SMC_RWSETUP (7 << 24) /* Read & Write Signal Time Setup */ +#define AT91_SMC_RWSETUP_(x) ((x) << 24) +#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */ +#define AT91_SMC_RWHOLD_(x) ((x) << 28) + +/* SDRAM Controller registers */ +#define AT91_SDRAMC_MR (AT91_MC + 0x90) /* Mode Register */ +#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */ +#define AT91_SDRAMC_MODE_NORMAL (0 << 0) +#define AT91_SDRAMC_MODE_NOP (1 << 0) +#define AT91_SDRAMC_MODE_PRECHARGE (2 << 0) +#define AT91_SDRAMC_MODE_LMR (3 << 0) +#define AT91_SDRAMC_MODE_REFRESH (4 << 0) +#define AT91_SDRAMC_DBW (1 << 4) /* Data Bus Width */ +#define AT91_SDRAMC_DBW_32 (0 << 4) +#define AT91_SDRAMC_DBW_16 (1 << 4) + +#define AT91_SDRAMC_TR (AT91_MC + 0x94) /* Refresh Timer Register */ +#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */ + +#define AT91_SDRAMC_CR (AT91_MC + 0x98) /* Configuration Register */ +#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */ +#define AT91_SDRAMC_NC_8 (0 << 0) +#define AT91_SDRAMC_NC_9 (1 << 0) +#define AT91_SDRAMC_NC_10 (2 << 0) +#define AT91_SDRAMC_NC_11 (3 << 0) +#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */ +#define AT91_SDRAMC_NR_11 (0 << 2) +#define AT91_SDRAMC_NR_12 (1 << 2) +#define AT91_SDRAMC_NR_13 (2 << 2) +#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */ +#define AT91_SDRAMC_NB_2 (0 << 4) +#define AT91_SDRAMC_NB_4 (1 << 4) +#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */ +#define AT91_SDRAMC_CAS_2 (2 << 5) +#define AT91_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */ +#define AT91_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */ +#define AT91_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */ +#define AT91_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */ +#define AT91_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */ +#define AT91_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */ + +#define AT91_SDRAMC_SRR (AT91_MC + 0x9c) /* Self Refresh Register */ +#define AT91_SDRAMC_LPR (AT91_MC + 0xa0) /* Low Power Register */ +#define AT91_SDRAMC_IER (AT91_MC + 0xa4) /* Interrupt Enable Register */ +#define AT91_SDRAMC_IDR (AT91_MC + 0xa8) /* Interrupt Disable Register */ +#define AT91_SDRAMC_IMR (AT91_MC + 0xac) /* Interrupt Mask Register */ +#define AT91_SDRAMC_ISR (AT91_MC + 0xb0) /* Interrupt Status Register */ + +/* Burst Flash Controller register */ +#define AT91_BFC_MR (AT91_MC + 0xc0) /* Mode Register */ +#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */ +#define AT91_BFC_BFCOM_DISABLED (0 << 0) +#define AT91_BFC_BFCOM_ASYNC (1 << 0) +#define AT91_BFC_BFCOM_BURST (2 << 0) +#define AT91_BFC_BFCC (3 << 2) /* Burst Flash Controller Clock */ +#define AT91_BFC_BFCC_MCK (1 << 2) +#define AT91_BFC_BFCC_DIV2 (2 << 2) +#define AT91_BFC_BFCC_DIV4 (3 << 2) +#define AT91_BFC_AVL (0xf << 4) /* Address Valid Latency */ +#define AT91_BFC_PAGES (7 << 8) /* Page Size */ +#define AT91_BFC_PAGES_NO_PAGE (0 << 8) +#define AT91_BFC_PAGES_16 (1 << 8) +#define AT91_BFC_PAGES_32 (2 << 8) +#define AT91_BFC_PAGES_64 (3 << 8) +#define AT91_BFC_PAGES_128 (4 << 8) +#define AT91_BFC_PAGES_256 (5 << 8) +#define AT91_BFC_PAGES_512 (6 << 8) +#define AT91_BFC_PAGES_1024 (7 << 8) +#define AT91_BFC_OEL (3 << 12) /* Output Enable Latency */ +#define AT91_BFC_BAAEN (1 << 16) /* Burst Address Advance Enable */ +#define AT91_BFC_BFOEH (1 << 17) /* Burst Flash Output Enable Handling */ +#define AT91_BFC_MUXEN (1 << 18) /* Multiplexed Bus Enable */ +#define AT91_BFC_RDYEN (1 << 19) /* Ready Enable Mode */ + +#endif diff --git a/include/asm-arm/arch-at91/at91sam9260.h b/include/asm-arm/arch-at91/at91sam9260.h new file mode 100644 index 000000000000..73d93ae9243e --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam9260.h @@ -0,0 +1,125 @@ +/* + * include/asm-arm/arch-at91/at91sam9260.h + * + * (C) 2006 Andrew Victor + * + * Common definitions. + * Based on AT91SAM9260 datasheet revision A (Preliminary). + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM9260_H +#define AT91SAM9260_H + +/* + * Peripheral identifiers/interrupts. + */ +#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ +#define AT91_ID_SYS 1 /* System Peripherals */ +#define AT91SAM9260_ID_PIOA 2 /* Parallel IO Controller A */ +#define AT91SAM9260_ID_PIOB 3 /* Parallel IO Controller B */ +#define AT91SAM9260_ID_PIOC 4 /* Parallel IO Controller C */ +#define AT91SAM9260_ID_ADC 5 /* Analog-to-Digital Converter */ +#define AT91SAM9260_ID_US0 6 /* USART 0 */ +#define AT91SAM9260_ID_US1 7 /* USART 1 */ +#define AT91SAM9260_ID_US2 8 /* USART 2 */ +#define AT91SAM9260_ID_MCI 9 /* Multimedia Card Interface */ +#define AT91SAM9260_ID_UDP 10 /* USB Device Port */ +#define AT91SAM9260_ID_TWI 11 /* Two-Wire Interface */ +#define AT91SAM9260_ID_SPI0 12 /* Serial Peripheral Interface 0 */ +#define AT91SAM9260_ID_SPI1 13 /* Serial Peripheral Interface 1 */ +#define AT91SAM9260_ID_SSC 14 /* Serial Synchronous Controller */ +#define AT91SAM9260_ID_TC0 17 /* Timer Counter 0 */ +#define AT91SAM9260_ID_TC1 18 /* Timer Counter 1 */ +#define AT91SAM9260_ID_TC2 19 /* Timer Counter 2 */ +#define AT91SAM9260_ID_UHP 20 /* USB Host port */ +#define AT91SAM9260_ID_EMAC 21 /* Ethernet */ +#define AT91SAM9260_ID_ISI 22 /* Image Sensor Interface */ +#define AT91SAM9260_ID_US3 23 /* USART 3 */ +#define AT91SAM9260_ID_US4 24 /* USART 4 */ +#define AT91SAM9260_ID_US5 25 /* USART 5 */ +#define AT91SAM9260_ID_TC3 26 /* Timer Counter 3 */ +#define AT91SAM9260_ID_TC4 27 /* Timer Counter 4 */ +#define AT91SAM9260_ID_TC5 28 /* Timer Counter 5 */ +#define AT91SAM9260_ID_IRQ0 29 /* Advanced Interrupt Controller (IRQ0) */ +#define AT91SAM9260_ID_IRQ1 30 /* Advanced Interrupt Controller (IRQ1) */ +#define AT91SAM9260_ID_IRQ2 31 /* Advanced Interrupt Controller (IRQ2) */ + + +/* + * User Peripheral physical base addresses. + */ +#define AT91SAM9260_BASE_TCB0 0xfffa0000 +#define AT91SAM9260_BASE_TC0 0xfffa0000 +#define AT91SAM9260_BASE_TC1 0xfffa0040 +#define AT91SAM9260_BASE_TC2 0xfffa0080 +#define AT91SAM9260_BASE_UDP 0xfffa4000 +#define AT91SAM9260_BASE_MCI 0xfffa8000 +#define AT91SAM9260_BASE_TWI 0xfffac000 +#define AT91SAM9260_BASE_US0 0xfffb0000 +#define AT91SAM9260_BASE_US1 0xfffb4000 +#define AT91SAM9260_BASE_US2 0xfffb8000 +#define AT91SAM9260_BASE_SSC 0xfffbc000 +#define AT91SAM9260_BASE_ISI 0xfffc0000 +#define AT91SAM9260_BASE_EMAC 0xfffc4000 +#define AT91SAM9260_BASE_SPI0 0xfffc8000 +#define AT91SAM9260_BASE_SPI1 0xfffcc000 +#define AT91SAM9260_BASE_US3 0xfffd0000 +#define AT91SAM9260_BASE_US4 0xfffd4000 +#define AT91SAM9260_BASE_US5 0xfffd8000 +#define AT91SAM9260_BASE_TCB1 0xfffdc000 +#define AT91SAM9260_BASE_TC3 0xfffdc000 +#define AT91SAM9260_BASE_TC4 0xfffdc040 +#define AT91SAM9260_BASE_TC5 0xfffdc080 +#define AT91SAM9260_BASE_ADC 0xfffe0000 +#define AT91_BASE_SYS 0xffffe800 + +/* + * System Peripherals (offset from AT91_BASE_SYS) + */ +#define AT91_ECC (0xffffe800 - AT91_BASE_SYS) +#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS) +#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) +#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) +#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS) +#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) +#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) +#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) +#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) +#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) +#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) +#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) +#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) +#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) +#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) +#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) +#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) + + +/* + * Internal Memory. + */ +#define AT91SAM9260_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91SAM9260_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ + +#define AT91SAM9260_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ +#define AT91SAM9260_SRAM0_SIZE SZ_4K /* Internal SRAM 0 size (4Kb) */ +#define AT91SAM9260_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ +#define AT91SAM9260_SRAM1_SIZE SZ_4K /* Internal SRAM 1 size (4Kb) */ + +#define AT91SAM9260_UHP_BASE 0x00500000 /* USB Host controller */ + +#if 0 +/* + * PIO pin definitions (peripheral A/B multiplexing). + */ + +// TODO: Add + +#endif + +#endif diff --git a/include/asm-arm/arch-at91/at91sam9260_matrix.h b/include/asm-arm/arch-at91/at91sam9260_matrix.h new file mode 100644 index 000000000000..573e97a47d22 --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam9260_matrix.h @@ -0,0 +1,78 @@ +/* + * include/asm-arm/arch-at91/at91sam9260_matrix.h + * + * Memory Controllers (MATRIX, EBI) - System peripherals registers. + * Based on AT91SAM9260 datasheet revision B. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM9260_MATRIX_H +#define AT91SAM9260_MATRIX_H + +#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */ +#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */ +#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */ +#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */ +#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */ +#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x04) /* Master Configuration Register 5 */ +#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ +#define AT91_MATRIX_ULBT_INFINITE (0 << 0) +#define AT91_MATRIX_ULBT_SINGLE (1 << 0) +#define AT91_MATRIX_ULBT_FOUR (2 << 0) +#define AT91_MATRIX_ULBT_EIGHT (3 << 0) +#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) + +#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */ +#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */ +#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */ +#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */ +#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */ +#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ +#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ +#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) +#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) +#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) +#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ +#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */ +#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24) +#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24) + +#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */ +#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */ +#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */ +#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */ +#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */ +#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ +#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ +#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ +#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ +#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ +#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ + +#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */ +#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ +#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ + +#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x11C) /* EBI Chip Select Assignment Register */ +#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ +#define AT91_MATRIX_CS1A_SMC (0 << 1) +#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) +#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ +#define AT91_MATRIX_CS3A_SMC (0 << 3) +#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) +#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ +#define AT91_MATRIX_CS4A_SMC (0 << 4) +#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) +#define AT91_MATRIX_CS5A (1 << 5 ) /* Chip Select 5 Assignment */ +#define AT91_MATRIX_CS5A_SMC (0 << 5) +#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) +#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ +#define AT91_MATRIX_VDDIOMSEL (1 << 16) /* Memory voltage selection */ +#define AT91_MATRIX_VDDIOMSEL_1_8V (0 << 16) +#define AT91_MATRIX_VDDIOMSEL_3_3V (1 << 16) + +#endif diff --git a/include/asm-arm/arch-at91/at91sam9261.h b/include/asm-arm/arch-at91/at91sam9261.h new file mode 100644 index 000000000000..01b58ffe2e27 --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam9261.h @@ -0,0 +1,292 @@ +/* + * include/asm-arm/arch-at91/at91sam9261.h + * + * Copyright (C) SAN People + * + * Common definitions. + * Based on AT91SAM9261 datasheet revision E. (Preliminary) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM9261_H +#define AT91SAM9261_H + +/* + * Peripheral identifiers/interrupts. + */ +#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ +#define AT91_ID_SYS 1 /* System Peripherals */ +#define AT91SAM9261_ID_PIOA 2 /* Parallel IO Controller A */ +#define AT91SAM9261_ID_PIOB 3 /* Parallel IO Controller B */ +#define AT91SAM9261_ID_PIOC 4 /* Parallel IO Controller C */ +#define AT91SAM9261_ID_US0 6 /* USART 0 */ +#define AT91SAM9261_ID_US1 7 /* USART 1 */ +#define AT91SAM9261_ID_US2 8 /* USART 2 */ +#define AT91SAM9261_ID_MCI 9 /* Multimedia Card Interface */ +#define AT91SAM9261_ID_UDP 10 /* USB Device Port */ +#define AT91SAM9261_ID_TWI 11 /* Two-Wire Interface */ +#define AT91SAM9261_ID_SPI0 12 /* Serial Peripheral Interface 0 */ +#define AT91SAM9261_ID_SPI1 13 /* Serial Peripheral Interface 1 */ +#define AT91SAM9261_ID_SSC0 14 /* Serial Synchronous Controller 0 */ +#define AT91SAM9261_ID_SSC1 15 /* Serial Synchronous Controller 1 */ +#define AT91SAM9261_ID_SSC2 16 /* Serial Synchronous Controller 2 */ +#define AT91SAM9261_ID_TC0 17 /* Timer Counter 0 */ +#define AT91SAM9261_ID_TC1 18 /* Timer Counter 1 */ +#define AT91SAM9261_ID_TC2 19 /* Timer Counter 2 */ +#define AT91SAM9261_ID_UHP 20 /* USB Host port */ +#define AT91SAM9261_ID_LCDC 21 /* LDC Controller */ +#define AT91SAM9261_ID_IRQ0 29 /* Advanced Interrupt Controller (IRQ0) */ +#define AT91SAM9261_ID_IRQ1 30 /* Advanced Interrupt Controller (IRQ1) */ +#define AT91SAM9261_ID_IRQ2 31 /* Advanced Interrupt Controller (IRQ2) */ + + +/* + * User Peripheral physical base addresses. + */ +#define AT91SAM9261_BASE_TCB0 0xfffa0000 +#define AT91SAM9261_BASE_TC0 0xfffa0000 +#define AT91SAM9261_BASE_TC1 0xfffa0040 +#define AT91SAM9261_BASE_TC2 0xfffa0080 +#define AT91SAM9261_BASE_UDP 0xfffa4000 +#define AT91SAM9261_BASE_MCI 0xfffa8000 +#define AT91SAM9261_BASE_TWI 0xfffac000 +#define AT91SAM9261_BASE_US0 0xfffb0000 +#define AT91SAM9261_BASE_US1 0xfffb4000 +#define AT91SAM9261_BASE_US2 0xfffb8000 +#define AT91SAM9261_BASE_SSC0 0xfffbc000 +#define AT91SAM9261_BASE_SSC1 0xfffc0000 +#define AT91SAM9261_BASE_SSC2 0xfffc4000 +#define AT91SAM9261_BASE_SPI0 0xfffc8000 +#define AT91SAM9261_BASE_SPI1 0xfffcc000 +#define AT91_BASE_SYS 0xffffea00 + + +/* + * System Peripherals (offset from AT91_BASE_SYS) + */ +#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS) +#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) +#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) +#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) +#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) +#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) +#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) +#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) +#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) +#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) +#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) +#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) +#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) +#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) +#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) + + +/* + * Internal Memory. + */ +#define AT91SAM9261_SRAM_BASE 0x00300000 /* Internal SRAM base address */ +#define AT91SAM9261_SRAM_SIZE 0x00028000 /* Internal SRAM size (160Kb) */ + +#define AT91SAM9261_ROM_BASE 0x00400000 /* Internal ROM base address */ +#define AT91SAM9261_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ + +#define AT91SAM9261_UHP_BASE 0x00500000 /* USB Host controller */ +#define AT91SAM9261_LCDC_BASE 0x00600000 /* LDC controller */ + + +#if 0 +/* + * PIO pin definitions (peripheral A/B multiplexing). + */ +#define AT91_PA0_SPI0_MISO (1 << 0) /* A: SPI0 Master In Slave */ +#define AT91_PA0_MCDA0 (1 << 0) /* B: Multimedia Card A Data 0 */ +#define AT91_PA1_SPI0_MOSI (1 << 1) /* A: SPI0 Master Out Slave */ +#define AT91_PA1_MCCDA (1 << 1) /* B: Multimedia Card A Command */ +#define AT91_PA2_SPI0_SPCK (1 << 2) /* A: SPI0 Serial Clock */ +#define AT91_PA2_MCCK (1 << 2) /* B: Multimedia Card Clock */ +#define AT91_PA3_SPI0_NPCS0 (1 << 3) /* A: SPI0 Peripheral Chip Select 0 */ +#define AT91_PA4_SPI0_NPCS1 (1 << 4) /* A: SPI0 Peripheral Chip Select 1 */ +#define AT91_PA4_MCDA1 (1 << 4) /* B: Multimedia Card A Data 1 */ +#define AT91_PA5_SPI0_NPCS2 (1 << 5) /* A: SPI0 Peripheral Chip Select 2 */ +#define AT91_PA5_MCDA2 (1 << 5) /* B: Multimedia Card A Data 2 */ +#define AT91_PA6_SPI0_NPCS3 (1 << 6) /* A: SPI0 Peripheral Chip Select 3 */ +#define AT91_PA6_MCDA3 (1 << 6) /* B: Multimedia Card A Data 3 */ +#define AT91_PA7_TWD (1 << 7) /* A: TWI Two-wire Serial Data */ +#define AT91_PA7_PCK0 (1 << 7) /* B: PMC Programmable clock Output 0 */ +#define AT91_PA8_TWCK (1 << 8) /* A: TWI Two-wire Serial Clock */ +#define AT91_PA8_PCK1 (1 << 8) /* B: PMC Programmable clock Output 1 */ +#define AT91_PA9_DRXD (1 << 9) /* A: DBGU Debug Receive Data */ +#define AT91_PA9_PCK2 (1 << 9) /* B: PMC Programmable clock Output 2 */ +#define AT91_PA10_DTXD (1 << 10) /* A: DBGU Debug Transmit Data */ +#define AT91_PA10_PCK3 (1 << 10) /* B: PMC Programmable clock Output 3 */ +#define AT91_PA11_TSYNC (1 << 11) /* A: Trace Synchronization Signal */ +#define AT91_PA11_SCK1 (1 << 11) /* B: USART1 Serial Clock */ +#define AT91_PA12_TCLK (1 << 12) /* A: Trace Clock */ +#define AT91_PA12_RTS1 (1 << 12) /* B: USART1 Ready To Send */ +#define AT91_PA13_TPS0 (1 << 13) /* A: Trace ARM Pipeline Status 0 */ +#define AT91_PA13_CTS1 (1 << 13) /* B: USART1 Clear To Send */ +#define AT91_PA14_TPS1 (1 << 14) /* A: Trace ARM Pipeline Status 1 */ +#define AT91_PA14_SCK2 (1 << 14) /* B: USART2 Serial Clock */ +#define AT91_PA15_TPS2 (1 << 15) /* A: Trace ARM Pipeline Status 2 */ +#define AT91_PA15_RTS2 (1 << 15) /* B: USART2 Ready To Send */ +#define AT91_PA16_TPK0 (1 << 16) /* A: Trace Packet Port 0 */ +#define AT91_PA16_CTS2 (1 << 16) /* B: USART2 Clear To Send */ +#define AT91_PA17_TPK1 (1 << 17) /* A: Trace Packet Port 1 */ +#define AT91_PA17_TF1 (1 << 17) /* B: SSC1 Transmit Frame Sync */ +#define AT91_PA18_TPK2 (1 << 18) /* A: Trace Packet Port 2 */ +#define AT91_PA18_TK1 (1 << 18) /* B: SSC1 Transmit Clock */ +#define AT91_PA19_TPK3 (1 << 19) /* A: Trace Packet Port 3 */ +#define AT91_PA19_TD1 (1 << 19) /* B: SSC1 Transmit Data */ +#define AT91_PA20_TPK4 (1 << 20) /* A: Trace Packet Port 4 */ +#define AT91_PA20_RD1 (1 << 20) /* B: SSC1 Receive Data */ +#define AT91_PA21_TPK5 (1 << 21) /* A: Trace Packet Port 5 */ +#define AT91_PA21_RK1 (1 << 21) /* B: SSC1 Receive Clock */ +#define AT91_PA22_TPK6 (1 << 22) /* A: Trace Packet Port 6 */ +#define AT91_PA22_RF1 (1 << 22) /* B: SSC1 Receive Frame Sync */ +#define AT91_PA23_TPK7 (1 << 23) /* A: Trace Packet Port 7 */ +#define AT91_PA23_RTS0 (1 << 23) /* B: USART0 Ready To Send */ +#define AT91_PA24_TPK8 (1 << 24) /* A: Trace Packet Port 8 */ +#define AT91_PA24_SPI1_NPCS1 (1 << 24) /* B: SPI1 Peripheral Chip Select 1 */ +#define AT91_PA25_TPK9 (1 << 25) /* A: Trace Packet Port 9 */ +#define AT91_PA25_SPI1_NPCS2 (1 << 25) /* B: SPI1 Peripheral Chip Select 2 */ +#define AT91_PA26_TPK10 (1 << 26) /* A: Trace Packet Port 10 */ +#define AT91_PA26_SPI1_NPCS3 (1 << 26) /* B: SPI1 Peripheral Chip Select 3 */ +#define AT91_PA27_TPK11 (1 << 27) /* A: Trace Packet Port 11 */ +#define AT91_PA27_SPI0_NPCS1 (1 << 27) /* B: SPI0 Peripheral Chip Select 1 */ +#define AT91_PA28_TPK12 (1 << 28) /* A: Trace Packet Port 12 */ +#define AT91_PA28_SPI0_NPCS2 (1 << 28) /* B: SPI0 Peripheral Chip Select 2 */ +#define AT91_PA29_TPK13 (1 << 29) /* A: Trace Packet Port 13 */ +#define AT91_PA29_SPI0_NPCS3 (1 << 29) /* B: SPI0 Peripheral Chip Select 3 */ +#define AT91_PA30_TPK14 (1 << 30) /* A: Trace Packet Port 14 */ +#define AT91_PA30_A23 (1 << 30) /* B: Address Bus bit 23 */ +#define AT91_PA31_TPK15 (1 << 31) /* A: Trace Packet Port 15 */ +#define AT91_PA31_A24 (1 << 31) /* B: Address Bus bit 24 */ + +#define AT91_PB0_LCDVSYNC (1 << 0) /* A: LCD Vertical Synchronization */ +#define AT91_PB1_LCDHSYNC (1 << 1) /* A: LCD Horizontal Synchronization */ +#define AT91_PB2_LCDDOTCK (1 << 2) /* A: LCD Dot Clock */ +#define AT91_PB2_PCK0 (1 << 2) /* B: PMC Programmable clock Output 0 */ +#define AT91_PB3_LCDDEN (1 << 3) /* A: LCD Data Enable */ +#define AT91_PB4_LCDCC (1 << 4) /* A: LCD Contrast Control */ +#define AT91_PB4_LCDD2 (1 << 4) /* B: LCD Data Bus Bit 2 */ +#define AT91_PB5_LCDD0 (1 << 5) /* A: LCD Data Bus Bit 0 */ +#define AT91_PB5_LCDD3 (1 << 5) /* B: LCD Data Bus Bit 3 */ +#define AT91_PB6_LCDD1 (1 << 6) /* A: LCD Data Bus Bit 1 */ +#define AT91_PB6_LCDD4 (1 << 6) /* B: LCD Data Bus Bit 4 */ +#define AT91_PB7_LCDD2 (1 << 7) /* A: LCD Data Bus Bit 2 */ +#define AT91_PB7_LCDD5 (1 << 7) /* B: LCD Data Bus Bit 5 */ +#define AT91_PB8_LCDD3 (1 << 8) /* A: LCD Data Bus Bit 3 */ +#define AT91_PB8_LCDD6 (1 << 8) /* B: LCD Data Bus Bit 6 */ +#define AT91_PB9_LCDD4 (1 << 9) /* A: LCD Data Bus Bit 4 */ +#define AT91_PB9_LCDD7 (1 << 9) /* B: LCD Data Bus Bit 7 */ +#define AT91_PB10_LCDD5 (1 << 10) /* A: LCD Data Bus Bit 5 */ +#define AT91_PB10_LCDD10 (1 << 10) /* B: LCD Data Bus Bit 10 */ +#define AT91_PB11_LCDD6 (1 << 11) /* A: LCD Data Bus Bit 6 */ +#define AT91_PB11_LCDD11 (1 << 11) /* B: LCD Data Bus Bit 11 */ +#define AT91_PB12_LCDD7 (1 << 12) /* A: LCD Data Bus Bit 7 */ +#define AT91_PB12_LCDD12 (1 << 12) /* B: LCD Data Bus Bit 12 */ +#define AT91_PB13_LCDD8 (1 << 13) /* A: LCD Data Bus Bit 8 */ +#define AT91_PB13_LCDD13 (1 << 13) /* B: LCD Data Bus Bit 13 */ +#define AT91_PB14_LCDD9 (1 << 14) /* A: LCD Data Bus Bit 9 */ +#define AT91_PB14_LCDD14 (1 << 14) /* B: LCD Data Bus Bit 14 */ +#define AT91_PB15_LCDD10 (1 << 15) /* A: LCD Data Bus Bit 10 */ +#define AT91_PB15_LCDD15 (1 << 15) /* B: LCD Data Bus Bit 15 */ +#define AT91_PB16_LCDD11 (1 << 16) /* A: LCD Data Bus Bit 11 */ +#define AT91_PB16_LCDD19 (1 << 16) /* B: LCD Data Bus Bit 19 */ +#define AT91_PB17_LCDD12 (1 << 17) /* A: LCD Data Bus Bit 12 */ +#define AT91_PB17_LCDD20 (1 << 17) /* B: LCD Data Bus Bit 20 */ +#define AT91_PB18_LCDD13 (1 << 18) /* A: LCD Data Bus Bit 13 */ +#define AT91_PB18_LCDD21 (1 << 18) /* B: LCD Data Bus Bit 21 */ +#define AT91_PB19_LCDD14 (1 << 19) /* A: LCD Data Bus Bit 14 */ +#define AT91_PB19_LCDD22 (1 << 19) /* B: LCD Data Bus Bit 22 */ +#define AT91_PB20_LCDD15 (1 << 20) /* A: LCD Data Bus Bit 15 */ +#define AT91_PB20_LCDD23 (1 << 20) /* B: LCD Data Bus Bit 23 */ +#define AT91_PB21_TF0 (1 << 21) /* A: SSC0 Transmit Frame Sync */ +#define AT91_PB21_LCDD16 (1 << 21) /* B: LCD Data Bus Bit 16 */ +#define AT91_PB22_TK0 (1 << 22) /* A: SSC0 Transmit Clock */ +#define AT91_PB22_LCDD17 (1 << 22) /* B: LCD Data Bus Bit 17 */ +#define AT91_PB23_TD0 (1 << 23) /* A: SSC0 Transmit Data */ +#define AT91_PB23_LCDD18 (1 << 23) /* B: LCD Data Bus Bit 18 */ +#define AT91_PB24_RD0 (1 << 24) /* A: SSC0 Receive Data */ +#define AT91_PB24_LCDD19 (1 << 24) /* B: LCD Data Bus Bit 19 */ +#define AT91_PB25_RK0 (1 << 25) /* A: SSC0 Receive Clock */ +#define AT91_PB25_LCDD20 (1 << 25) /* B: LCD Data Bus Bit 20 */ +#define AT91_PB26_RF0 (1 << 26) /* A: SSC0 Receive Frame Sync */ +#define AT91_PB26_LCDD21 (1 << 26) /* B: LCD Data Bus Bit 21 */ +#define AT91_PB27_SPI1_NPCS1 (1 << 27) /* A: SPI1 Peripheral Chip Select 1 */ +#define AT91_PB27_LCDD22 (1 << 27) /* B: LCD Data Bus Bit 22 */ +#define AT91_PB28_SPI1_NPCS0 (1 << 28) /* A: SPI1 Peripheral Chip Select 0 */ +#define AT91_PB28_LCDD23 (1 << 28) /* B: LCD Data Bus Bit 23 */ +#define AT91_PB29_SPI1_SPCK (1 << 29) /* A: SPI1 Serial Clock */ +#define AT91_PB29_IRQ2 (1 << 29) /* B: Interrupt input 2 */ +#define AT91_PB30_SPI1_MISO (1 << 30) /* A: SPI1 Master In Slave */ +#define AT91_PB30_IRQ1 (1 << 30) /* B: Interrupt input 1 */ +#define AT91_PB31_SPI1_MOSI (1 << 31) /* A: SPI1 Master Out Slave */ +#define AT91_PB31_PCK2 (1 << 31) /* B: PMC Programmable clock Output 2 */ + +#define AT91_PC0_SMOE (1 << 0) /* A: SmartMedia Output Enable */ +#define AT91_PC0_NCS6 (1 << 0) /* B: Chip Select 6 */ +#define AT91_PC1_SMWE (1 << 1) /* A: SmartMedia Write Enable */ +#define AT91_PC1_NCS7 (1 << 1) /* B: Chip Select 7 */ +#define AT91_PC2_NWAIT (1 << 2) /* A: NWAIT */ +#define AT91_PC2_IRQ0 (1 << 2) /* B: Interrupt input 0 */ +#define AT91_PC3_A25_CFRNW (1 << 3) /* A: Address Bus[25] / Compact Flash Read Not Write */ +#define AT91_PC4_NCS4_CFCS0 (1 << 4) /* A: Chip Select 4 / CompactFlash Chip Select 0 */ +#define AT91_PC5_NCS5_CFCS1 (1 << 5) /* A: Chip Select 5 / CompactFlash Chip Select 1 */ +#define AT91_PC6_CFCE1 (1 << 6) /* A: CompactFlash Chip Enable 1 */ +#define AT91_PC7_CFCE2 (1 << 7) /* A: CompactFlash Chip Enable 2 */ +#define AT91_PC8_TXD0 (1 << 8) /* A: USART0 Transmit Data */ +#define AT91_PC8_PCK2 (1 << 8) /* B: PMC Programmable clock Output 2 */ +#define AT91_PC9_RXD0 (1 << 9) /* A: USART0 Receive Data */ +#define AT91_PC9_PCK3 (1 << 9) /* B: PMC Programmable clock Output 3 */ +#define AT91_PC10_RTS0 (1 << 10) /* A: USART0 Ready To Send */ +#define AT91_PC10_SCK0 (1 << 10) /* B: USART0 Serial Clock */ +#define AT91_PC11_CTS0 (1 << 11) /* A: USART0 Clear To Send */ +#define AT91_PC11_FIQ (1 << 11) /* B: AIC Fast Interrupt Input */ +#define AT91_PC12_TXD1 (1 << 12) /* A: USART1 Transmit Data */ +#define AT91_PC12_NCS6 (1 << 12) /* B: Chip Select 6 */ +#define AT91_PC13_RXD1 (1 << 13) /* A: USART1 Receive Data */ +#define AT91_PC13_NCS7 (1 << 13) /* B: Chip Select 7 */ +#define AT91_PC14_TXD2 (1 << 14) /* A: USART2 Transmit Data */ +#define AT91_PC14_SPI1_NPCS2 (1 << 14) /* B: SPI1 Peripheral Chip Select 2 */ +#define AT91_PC15_RXD2 (1 << 15) /* A: USART2 Receive Data */ +#define AT91_PC15_SPI1_NPCS3 (1 << 15) /* B: SPI1 Peripheral Chip Select 3 */ +#define AT91_PC16_D16 (1 << 16) /* A: Data Bus [16] */ +#define AT91_PC16_TCLK0 (1 << 16) /* B: Timer Counter 0 external clock input */ +#define AT91_PC17_D17 (1 << 17) /* A: Data Bus [17] */ +#define AT91_PC17_TCLK1 (1 << 17) /* B: Timer Counter 1 external clock input */ +#define AT91_PC18_D18 (1 << 18) /* A: Data Bus [18] */ +#define AT91_PC18_TCLK2 (1 << 18) /* B: Timer Counter 2 external clock input */ +#define AT91_PC19_D19 (1 << 19) /* A: Data Bus [19] */ +#define AT91_PC19_TIOA0 (1 << 19) /* B: Timer Counter 0 Multipurpose Timer I/O Pin A */ +#define AT91_PC20_D20 (1 << 20) /* A: Data Bus [20] */ +#define AT91_PC20_TIOB0 (1 << 20) /* B: Timer Counter 0 Multipurpose Timer I/O Pin B */ +#define AT91_PC21_D21 (1 << 21) /* A: Data Bus [21] */ +#define AT91_PC21_TIOA1 (1 << 21) /* B: Timer Counter 1 Multipurpose Timer I/O Pin A */ +#define AT91_PC22_D22 (1 << 22) /* A: Data Bus [22] */ +#define AT91_PC22_TIOB1 (1 << 22) /* B: Timer Counter 1 Multipurpose Timer I/O Pin B */ +#define AT91_PC23_D23 (1 << 23) /* A: Data Bus [23] */ +#define AT91_PC23_TIOA2 (1 << 23) /* B: Timer Counter 2 Multipurpose Timer I/O Pin A */ +#define AT91_PC24_D24 (1 << 24) /* A: Data Bus [24] */ +#define AT91_PC24_TIOB2 (1 << 24) /* B: Timer Counter 2 Multipurpose Timer I/O Pin B */ +#define AT91_PC25_D25 (1 << 25) /* A: Data Bus [25] */ +#define AT91_PC25_TF2 (1 << 25) /* B: SSC2 Transmit Frame Sync */ +#define AT91_PC26_D26 (1 << 26) /* A: Data Bus [26] */ +#define AT91_PC26_TK2 (1 << 26) /* B: SSC2 Transmit Clock */ +#define AT91_PC27_D27 (1 << 27) /* A: Data Bus [27] */ +#define AT91_PC27_TD2 (1 << 27) /* B: SSC2 Transmit Data */ +#define AT91_PC28_D28 (1 << 28) /* A: Data Bus [28] */ +#define AT91_PC28_RD2 (1 << 28) /* B: SSC2 Receive Data */ +#define AT91_PC29_D29 (1 << 29) /* A: Data Bus [29] */ +#define AT91_PC29_RK2 (1 << 29) /* B: SSC2 Receive Clock */ +#define AT91_PC30_D30 (1 << 30) /* A: Data Bus [30] */ +#define AT91_PC30_RF2 (1 << 30) /* B: SSC2 Receive Frame Sync */ +#define AT91_PC31_D31 (1 << 31) /* A: Data Bus [31] */ +#define AT91_PC31_PCK1 (1 << 31) /* B: PMC Programmable clock Output 1 */ +#endif + +#endif diff --git a/include/asm-arm/arch-at91/at91sam9261_matrix.h b/include/asm-arm/arch-at91/at91sam9261_matrix.h new file mode 100644 index 000000000000..6f072421be5b --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam9261_matrix.h @@ -0,0 +1,62 @@ +/* + * include/asm-arm/arch-at91/at91sam9261_matrix.h + * + * Memory Controllers (MATRIX, EBI) - System peripherals registers. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM9261_MATRIX_H +#define AT91SAM9261_MATRIX_H + +#define AT91_MATRIX_MCFG (AT91_MATRIX + 0x00) /* Master Configuration Register */ +#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ +#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ + +#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x04) /* Slave Configuration Register 0 */ +#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x08) /* Slave Configuration Register 1 */ +#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x0C) /* Slave Configuration Register 2 */ +#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x10) /* Slave Configuration Register 3 */ +#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x14) /* Slave Configuration Register 4 */ +#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ +#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ +#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) +#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) +#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) +#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ + +#define AT91_MATRIX_TCR (AT91_MATRIX + 0x24) /* TCM Configuration Register */ +#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ +#define AT91_MATRIX_ITCM_0 (0 << 0) +#define AT91_MATRIX_ITCM_16 (5 << 0) +#define AT91_MATRIX_ITCM_32 (6 << 0) +#define AT91_MATRIX_ITCM_64 (7 << 0) +#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ +#define AT91_MATRIX_DTCM_0 (0 << 4) +#define AT91_MATRIX_DTCM_16 (5 << 4) +#define AT91_MATRIX_DTCM_32 (6 << 4) +#define AT91_MATRIX_DTCM_64 (7 << 4) + +#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x30) /* EBI Chip Select Assignment Register */ +#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ +#define AT91_MATRIX_CS1A_SMC (0 << 1) +#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) +#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ +#define AT91_MATRIX_CS3A_SMC (0 << 3) +#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) +#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ +#define AT91_MATRIX_CS4A_SMC (0 << 4) +#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) +#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */ +#define AT91_MATRIX_CS5A_SMC (0 << 5) +#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) +#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ + +#define AT91_MATRIX_USBPUCR (AT91_MATRIX + 0x34) /* USB Pad Pull-Up Control Register */ +#define AT91_MATRIX_USBPUCR_PUON (1 << 30) /* USB Device PAD Pull-up Enable */ + +#endif diff --git a/include/asm-arm/arch-at91/at91sam926x_mc.h b/include/asm-arm/arch-at91/at91sam926x_mc.h new file mode 100644 index 000000000000..355eee67ebca --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam926x_mc.h @@ -0,0 +1,134 @@ +/* + * include/asm-arm/arch-at91/at91sam926x_mc.h + * + * Memory Controllers (SMC, SDRAMC) - System peripherals registers. + * Based on AT91SAM9261 datasheet revision D. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM926x_MC_H +#define AT91SAM926x_MC_H + +/* SDRAM Controller (SDRAMC) registers */ +#define AT91_SDRAMC_MR (AT91_SDRAMC + 0x00) /* SDRAM Controller Mode Register */ +#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */ +#define AT91_SDRAMC_MODE_NORMAL 0 +#define AT91_SDRAMC_MODE_NOP 1 +#define AT91_SDRAMC_MODE_PRECHARGE 2 +#define AT91_SDRAMC_MODE_LMR 3 +#define AT91_SDRAMC_MODE_REFRESH 4 +#define AT91_SDRAMC_MODE_EXT_LMR 5 +#define AT91_SDRAMC_MODE_DEEP 6 + +#define AT91_SDRAMC_TR (AT91_SDRAMC + 0x04) /* SDRAM Controller Refresh Timer Register */ +#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */ + +#define AT91_SDRAMC_CR (AT91_SDRAMC + 0x08) /* SDRAM Controller Configuration Register */ +#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */ +#define AT91_SDRAMC_NC_8 (0 << 0) +#define AT91_SDRAMC_NC_9 (1 << 0) +#define AT91_SDRAMC_NC_10 (2 << 0) +#define AT91_SDRAMC_NC_11 (3 << 0) +#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */ +#define AT91_SDRAMC_NR_11 (0 << 2) +#define AT91_SDRAMC_NR_12 (1 << 2) +#define AT91_SDRAMC_NR_13 (2 << 2) +#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */ +#define AT91_SDRAMC_NB_2 (0 << 4) +#define AT91_SDRAMC_NB_4 (1 << 4) +#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */ +#define AT91_SDRAMC_CAS_1 (1 << 5) +#define AT91_SDRAMC_CAS_2 (2 << 5) +#define AT91_SDRAMC_CAS_3 (3 << 5) +#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */ +#define AT91_SDRAMC_DBW_32 (0 << 7) +#define AT91_SDRAMC_DBW_16 (1 << 7) +#define AT91_SDRAMC_TWR (0xf << 8) /* Write Recovery Delay */ +#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle Delay */ +#define AT91_SDRAMC_TRP (0xf << 16) /* Row Precharge Delay */ +#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column Delay */ +#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */ +#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */ + +#define AT91_SDRAMC_LPR (AT91_SDRAMC + 0x10) /* SDRAM Controller Low Power Register */ +#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */ +#define AT91_SDRAMC_LPCB_DISABLE 0 +#define AT91_SDRAMC_LPCB_SELF_REFRESH 1 +#define AT91_SDRAMC_LPCB_POWER_DOWN 2 +#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3 +#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array Self Refresh */ +#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */ +#define AT91_SDRAMC_DS (3 << 10) /* Drive Strenght */ +#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */ +#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12) +#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12) +#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12) + +#define AT91_SDRAMC_IER (AT91_SDRAMC + 0x14) /* SDRAM Controller Interrupt Enable Register */ +#define AT91_SDRAMC_IDR (AT91_SDRAMC + 0x18) /* SDRAM Controller Interrupt Disable Register */ +#define AT91_SDRAMC_IMR (AT91_SDRAMC + 0x1C) /* SDRAM Controller Interrupt Mask Register */ +#define AT91_SDRAMC_ISR (AT91_SDRAMC + 0x20) /* SDRAM Controller Interrupt Status Register */ +#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */ + +#define AT91_SDRAMC_MDR (AT91_SDRAMC + 0x24) /* SDRAM Memory Device Register */ +#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */ +#define AT91_SDRAMC_MD_SDRAM 0 +#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1 + + +/* Static Memory Controller (SMC) registers */ +#define AT91_SMC_SETUP(n) (AT91_SMC + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ +#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */ +#define AT91_SMC_NWESETUP_(x) ((x) << 0) +#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */ +#define AT91_SMC_NCS_WRSETUP_(x) ((x) << 8) +#define AT91_SMC_NRDSETUP (0x3f << 16) /* NRD Setup Length */ +#define AT91_SMC_NRDSETUP_(x) ((x) << 16) +#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */ +#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24) + +#define AT91_SMC_PULSE(n) (AT91_SMC + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ +#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */ +#define AT91_SMC_NWEPULSE_(x) ((x) << 0) +#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */ +#define AT91_SMC_NCS_WRPULSE_(x)((x) << 8) +#define AT91_SMC_NRDPULSE (0x7f << 16) /* NRD Pulse Length */ +#define AT91_SMC_NRDPULSE_(x) ((x) << 16) +#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */ +#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24) + +#define AT91_SMC_CYCLE(n) (AT91_SMC + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ +#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */ +#define AT91_SMC_NWECYCLE_(x) ((x) << 0) +#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */ +#define AT91_SMC_NRDCYCLE_(x) ((x) << 16) + +#define AT91_SMC_MODE(n) (AT91_SMC + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ +#define AT91_SMC_READMODE (1 << 0) /* Read Mode */ +#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */ +#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */ +#define AT91_SMC_EXNWMODE_DISABLE (0 << 4) +#define AT91_SMC_EXNWMODE_FROZEN (2 << 4) +#define AT91_SMC_EXNWMODE_READY (3 << 4) +#define AT91_SMC_BAT (1 << 8) /* Byte Access Type */ +#define AT91_SMC_BAT_SELECT (0 << 8) +#define AT91_SMC_BAT_WRITE (1 << 8) +#define AT91_SMC_DBW (3 << 12) /* Data Bus Width */ +#define AT91_SMC_DBW_8 (0 << 12) +#define AT91_SMC_DBW_16 (1 << 12) +#define AT91_SMC_DBW_32 (2 << 12) +#define AT91_SMC_TDF (0xf << 16) /* Data Float Time. */ +#define AT91_SMC_TDF_(x) ((x) << 16) +#define AT91_SMC_TDFMODE (1 << 20) /* TDF Optimization - Enabled */ +#define AT91_SMC_PMEN (1 << 24) /* Page Mode Enabled */ +#define AT91_SMC_PS (3 << 28) /* Page Size */ +#define AT91_SMC_PS_4 (0 << 28) +#define AT91_SMC_PS_8 (1 << 28) +#define AT91_SMC_PS_16 (2 << 28) +#define AT91_SMC_PS_32 (3 << 28) + +#endif diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h new file mode 100644 index 000000000000..bf1afd0081b6 --- /dev/null +++ b/include/asm-arm/arch-at91/board.h @@ -0,0 +1,121 @@ +/* + * include/asm-arm/arch-at91/board.h + * + * Copyright (C) 2005 HP Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +/* + * These are data structures found in platform_device.dev.platform_data, + * and describing board-specific data needed by drivers. For example, + * which pin is used for a given GPIO role. + * + * In 2.6, drivers should strongly avoid board-specific knowledge so + * that supporting new boards normally won't require driver patches. + * Most board-specific knowledge should be in arch/.../board-*.c files. + */ + +#ifndef __ASM_ARCH_BOARD_H +#define __ASM_ARCH_BOARD_H + +#include +#include +#include + + /* USB Device */ +struct at91_udc_data { + u8 vbus_pin; /* high == host powering us */ + u8 pullup_pin; /* high == D+ pulled up */ +}; +extern void __init at91_add_device_udc(struct at91_udc_data *data); + + /* Compact Flash */ +struct at91_cf_data { + u8 irq_pin; /* I/O IRQ */ + u8 det_pin; /* Card detect */ + u8 vcc_pin; /* power switching */ + u8 rst_pin; /* card reset */ + u8 chipselect; /* EBI Chip Select number */ +}; +extern void __init at91_add_device_cf(struct at91_cf_data *data); + + /* MMC / SD */ +struct at91_mmc_data { + u8 det_pin; /* card detect IRQ */ + unsigned slot_b:1; /* uses Slot B */ + unsigned wire4:1; /* (SD) supports DAT0..DAT3 */ + u8 wp_pin; /* (SD) writeprotect detect */ + u8 vcc_pin; /* power switching (high == on) */ +}; +extern void __init at91_add_device_mmc(struct at91_mmc_data *data); + + /* Ethernet */ +struct at91_eth_data { + u8 phy_irq_pin; /* PHY IRQ */ + u8 is_rmii; /* using RMII interface? */ +}; +extern void __init at91_add_device_eth(struct at91_eth_data *data); + +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) +#define eth_platform_data at91_eth_data +#endif + + /* USB Host */ +struct at91_usbh_data { + u8 ports; /* number of ports on root hub */ +}; +extern void __init at91_add_device_usbh(struct at91_usbh_data *data); + + /* NAND / SmartMedia */ +struct at91_nand_data { + u8 enable_pin; /* chip enable */ + u8 det_pin; /* card detect */ + u8 rdy_pin; /* ready/busy */ + u8 ale; /* address line number connected to ALE */ + u8 cle; /* address line number connected to CLE */ + u8 bus_width_16; /* buswidth is 16 bit */ + struct mtd_partition* (*partition_info)(int, int*); +}; +extern void __init at91_add_device_nand(struct at91_nand_data *data); + + /* I2C*/ +extern void __init at91_add_device_i2c(void); + + /* SPI */ +extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices); + + /* Serial */ +struct at91_uart_config { + unsigned short console_tty; /* tty number of serial console */ + unsigned short nr_tty; /* number of serial tty's */ + short tty_map[]; /* map UART to tty number */ +}; +extern struct platform_device *atmel_default_console_device; +extern void __init at91_init_serial(struct at91_uart_config *config); + +struct atmel_uart_data { + short use_dma_tx; /* use transmit DMA? */ + short use_dma_rx; /* use receive DMA? */ + void __iomem *regs; /* virtual base address, if any */ +}; +extern void __init at91_add_device_serial(void); + + /* LEDs */ +extern u8 at91_leds_cpu; +extern u8 at91_leds_timer; +extern void __init at91_init_leds(u8 cpu_led, u8 timer_led); + +#endif diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h new file mode 100644 index 000000000000..762eb41aa675 --- /dev/null +++ b/include/asm-arm/arch-at91/cpu.h @@ -0,0 +1,49 @@ +/* + * include/asm-arm/arch-at91/cpu.h + * + * Copyright (C) 2006 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#ifndef __ASM_ARCH_CPU_H +#define __ASM_ARCH_CPU_H + +#include +#include + + +#define ARCH_ID_AT91RM9200 0x09290780 +#define ARCH_ID_AT91SAM9260 0x019803a0 +#define ARCH_ID_AT91SAM9261 0x019703a0 + + +static inline unsigned long at91_cpu_identify(void) +{ + return (at91_sys_read(AT91_DBGU_CIDR) & ~AT91_CIDR_VERSION); +} + + +#ifdef CONFIG_ARCH_AT91RM9200 +#define cpu_is_at91rm9200() (at91_cpu_identify() == ARCH_ID_AT91RM9200) +#else +#define cpu_is_at91rm9200() (0) +#endif + +#ifdef CONFIG_ARCH_AT91SAM9260 +#define cpu_is_at91sam9260() (at91_cpu_identify() == ARCH_ID_AT91SAM9260) +#else +#define cpu_is_at91sam9260() (0) +#endif + +#ifdef CONFIG_ARCH_AT91SAM9261 +#define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261) +#else +#define cpu_is_at91sam9261() (0) +#endif + +#endif diff --git a/include/asm-arm/arch-at91/debug-macro.S b/include/asm-arm/arch-at91/debug-macro.S new file mode 100644 index 000000000000..20721ef1ed1b --- /dev/null +++ b/include/asm-arm/arch-at91/debug-macro.S @@ -0,0 +1,39 @@ +/* + * include/asm-arm/arch-at91/debug-macro.S + * + * Copyright (C) 2003-2005 SAN People + * + * Debugging macro include header + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include +#include + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =AT91_BASE_SYS @ System peripherals (phys address) + ldrne \rx, =AT91_VA_BASE_SYS @ System peripherals (virt address) + .endm + + .macro senduart,rd,rx + strb \rd, [\rx, #AT91_DBGU_THR] @ Write to Transmitter Holding Register + .endm + + .macro waituart,rd,rx +1001: ldr \rd, [\rx, #AT91_DBGU_SR] @ Read Status Register + tst \rd, #AT91_DBGU_TXRDY @ DBGU_TXRDY = 1 when ready to transmit + beq 1001b + .endm + + .macro busyuart,rd,rx +1001: ldr \rd, [\rx, #AT91_DBGU_SR] @ Read Status Register + tst \rd, #AT91_DBGU_TXEMPTY @ DBGU_TXEMPTY = 1 when transmission complete + beq 1001b + .endm + diff --git a/include/asm-arm/arch-at91/dma.h b/include/asm-arm/arch-at91/dma.h new file mode 100644 index 000000000000..774565412beb --- /dev/null +++ b/include/asm-arm/arch-at91/dma.h @@ -0,0 +1,19 @@ +/* + * include/asm-arm/arch-at91/dma.h + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ diff --git a/include/asm-arm/arch-at91/entry-macro.S b/include/asm-arm/arch-at91/entry-macro.S new file mode 100644 index 000000000000..a6f33832a178 --- /dev/null +++ b/include/asm-arm/arch-at91/entry-macro.S @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-at91/entry-macro.S + * + * Copyright (C) 2003-2005 SAN People + * + * Low-level IRQ helper macros for AT91RM9200 platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include + + .macro disable_fiq + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + ldr \base, =(AT91_VA_BASE_SYS) @ base virtual address of SYS peripherals + ldr \irqnr, [\base, #AT91_AIC_IVR] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt) + ldr \irqstat, [\base, #AT91_AIC_ISR] @ read interrupt source number + teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt + streq \tmp, [\base, #AT91_AIC_EOICR] @ not going to be handled further, then ACK it now. + .endm + diff --git a/include/asm-arm/arch-at91/gpio.h b/include/asm-arm/arch-at91/gpio.h new file mode 100644 index 000000000000..6d1a5eb34704 --- /dev/null +++ b/include/asm-arm/arch-at91/gpio.h @@ -0,0 +1,199 @@ +/* + * include/asm-arm/arch-at91/gpio.h + * + * Copyright (C) 2005 HP Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#ifndef __ASM_ARCH_AT91RM9200_GPIO_H +#define __ASM_ARCH_AT91RM9200_GPIO_H + +#include + +#define PIN_BASE NR_AIC_IRQS + +#define MAX_GPIO_BANKS 4 + +/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */ + +#define AT91_PIN_PA0 (PIN_BASE + 0x00 + 0) +#define AT91_PIN_PA1 (PIN_BASE + 0x00 + 1) +#define AT91_PIN_PA2 (PIN_BASE + 0x00 + 2) +#define AT91_PIN_PA3 (PIN_BASE + 0x00 + 3) +#define AT91_PIN_PA4 (PIN_BASE + 0x00 + 4) + +#define AT91_PIN_PA5 (PIN_BASE + 0x00 + 5) +#define AT91_PIN_PA6 (PIN_BASE + 0x00 + 6) +#define AT91_PIN_PA7 (PIN_BASE + 0x00 + 7) +#define AT91_PIN_PA8 (PIN_BASE + 0x00 + 8) +#define AT91_PIN_PA9 (PIN_BASE + 0x00 + 9) + +#define AT91_PIN_PA10 (PIN_BASE + 0x00 + 10) +#define AT91_PIN_PA11 (PIN_BASE + 0x00 + 11) +#define AT91_PIN_PA12 (PIN_BASE + 0x00 + 12) +#define AT91_PIN_PA13 (PIN_BASE + 0x00 + 13) +#define AT91_PIN_PA14 (PIN_BASE + 0x00 + 14) + +#define AT91_PIN_PA15 (PIN_BASE + 0x00 + 15) +#define AT91_PIN_PA16 (PIN_BASE + 0x00 + 16) +#define AT91_PIN_PA17 (PIN_BASE + 0x00 + 17) +#define AT91_PIN_PA18 (PIN_BASE + 0x00 + 18) +#define AT91_PIN_PA19 (PIN_BASE + 0x00 + 19) + +#define AT91_PIN_PA20 (PIN_BASE + 0x00 + 20) +#define AT91_PIN_PA21 (PIN_BASE + 0x00 + 21) +#define AT91_PIN_PA22 (PIN_BASE + 0x00 + 22) +#define AT91_PIN_PA23 (PIN_BASE + 0x00 + 23) +#define AT91_PIN_PA24 (PIN_BASE + 0x00 + 24) + +#define AT91_PIN_PA25 (PIN_BASE + 0x00 + 25) +#define AT91_PIN_PA26 (PIN_BASE + 0x00 + 26) +#define AT91_PIN_PA27 (PIN_BASE + 0x00 + 27) +#define AT91_PIN_PA28 (PIN_BASE + 0x00 + 28) +#define AT91_PIN_PA29 (PIN_BASE + 0x00 + 29) + +#define AT91_PIN_PA30 (PIN_BASE + 0x00 + 30) +#define AT91_PIN_PA31 (PIN_BASE + 0x00 + 31) + +#define AT91_PIN_PB0 (PIN_BASE + 0x20 + 0) +#define AT91_PIN_PB1 (PIN_BASE + 0x20 + 1) +#define AT91_PIN_PB2 (PIN_BASE + 0x20 + 2) +#define AT91_PIN_PB3 (PIN_BASE + 0x20 + 3) +#define AT91_PIN_PB4 (PIN_BASE + 0x20 + 4) + +#define AT91_PIN_PB5 (PIN_BASE + 0x20 + 5) +#define AT91_PIN_PB6 (PIN_BASE + 0x20 + 6) +#define AT91_PIN_PB7 (PIN_BASE + 0x20 + 7) +#define AT91_PIN_PB8 (PIN_BASE + 0x20 + 8) +#define AT91_PIN_PB9 (PIN_BASE + 0x20 + 9) + +#define AT91_PIN_PB10 (PIN_BASE + 0x20 + 10) +#define AT91_PIN_PB11 (PIN_BASE + 0x20 + 11) +#define AT91_PIN_PB12 (PIN_BASE + 0x20 + 12) +#define AT91_PIN_PB13 (PIN_BASE + 0x20 + 13) +#define AT91_PIN_PB14 (PIN_BASE + 0x20 + 14) + +#define AT91_PIN_PB15 (PIN_BASE + 0x20 + 15) +#define AT91_PIN_PB16 (PIN_BASE + 0x20 + 16) +#define AT91_PIN_PB17 (PIN_BASE + 0x20 + 17) +#define AT91_PIN_PB18 (PIN_BASE + 0x20 + 18) +#define AT91_PIN_PB19 (PIN_BASE + 0x20 + 19) + +#define AT91_PIN_PB20 (PIN_BASE + 0x20 + 20) +#define AT91_PIN_PB21 (PIN_BASE + 0x20 + 21) +#define AT91_PIN_PB22 (PIN_BASE + 0x20 + 22) +#define AT91_PIN_PB23 (PIN_BASE + 0x20 + 23) +#define AT91_PIN_PB24 (PIN_BASE + 0x20 + 24) + +#define AT91_PIN_PB25 (PIN_BASE + 0x20 + 25) +#define AT91_PIN_PB26 (PIN_BASE + 0x20 + 26) +#define AT91_PIN_PB27 (PIN_BASE + 0x20 + 27) +#define AT91_PIN_PB28 (PIN_BASE + 0x20 + 28) +#define AT91_PIN_PB29 (PIN_BASE + 0x20 + 29) + +#define AT91_PIN_PB30 (PIN_BASE + 0x20 + 30) +#define AT91_PIN_PB31 (PIN_BASE + 0x20 + 31) + +#define AT91_PIN_PC0 (PIN_BASE + 0x40 + 0) +#define AT91_PIN_PC1 (PIN_BASE + 0x40 + 1) +#define AT91_PIN_PC2 (PIN_BASE + 0x40 + 2) +#define AT91_PIN_PC3 (PIN_BASE + 0x40 + 3) +#define AT91_PIN_PC4 (PIN_BASE + 0x40 + 4) + +#define AT91_PIN_PC5 (PIN_BASE + 0x40 + 5) +#define AT91_PIN_PC6 (PIN_BASE + 0x40 + 6) +#define AT91_PIN_PC7 (PIN_BASE + 0x40 + 7) +#define AT91_PIN_PC8 (PIN_BASE + 0x40 + 8) +#define AT91_PIN_PC9 (PIN_BASE + 0x40 + 9) + +#define AT91_PIN_PC10 (PIN_BASE + 0x40 + 10) +#define AT91_PIN_PC11 (PIN_BASE + 0x40 + 11) +#define AT91_PIN_PC12 (PIN_BASE + 0x40 + 12) +#define AT91_PIN_PC13 (PIN_BASE + 0x40 + 13) +#define AT91_PIN_PC14 (PIN_BASE + 0x40 + 14) + +#define AT91_PIN_PC15 (PIN_BASE + 0x40 + 15) +#define AT91_PIN_PC16 (PIN_BASE + 0x40 + 16) +#define AT91_PIN_PC17 (PIN_BASE + 0x40 + 17) +#define AT91_PIN_PC18 (PIN_BASE + 0x40 + 18) +#define AT91_PIN_PC19 (PIN_BASE + 0x40 + 19) + +#define AT91_PIN_PC20 (PIN_BASE + 0x40 + 20) +#define AT91_PIN_PC21 (PIN_BASE + 0x40 + 21) +#define AT91_PIN_PC22 (PIN_BASE + 0x40 + 22) +#define AT91_PIN_PC23 (PIN_BASE + 0x40 + 23) +#define AT91_PIN_PC24 (PIN_BASE + 0x40 + 24) + +#define AT91_PIN_PC25 (PIN_BASE + 0x40 + 25) +#define AT91_PIN_PC26 (PIN_BASE + 0x40 + 26) +#define AT91_PIN_PC27 (PIN_BASE + 0x40 + 27) +#define AT91_PIN_PC28 (PIN_BASE + 0x40 + 28) +#define AT91_PIN_PC29 (PIN_BASE + 0x40 + 29) + +#define AT91_PIN_PC30 (PIN_BASE + 0x40 + 30) +#define AT91_PIN_PC31 (PIN_BASE + 0x40 + 31) + +#define AT91_PIN_PD0 (PIN_BASE + 0x60 + 0) +#define AT91_PIN_PD1 (PIN_BASE + 0x60 + 1) +#define AT91_PIN_PD2 (PIN_BASE + 0x60 + 2) +#define AT91_PIN_PD3 (PIN_BASE + 0x60 + 3) +#define AT91_PIN_PD4 (PIN_BASE + 0x60 + 4) + +#define AT91_PIN_PD5 (PIN_BASE + 0x60 + 5) +#define AT91_PIN_PD6 (PIN_BASE + 0x60 + 6) +#define AT91_PIN_PD7 (PIN_BASE + 0x60 + 7) +#define AT91_PIN_PD8 (PIN_BASE + 0x60 + 8) +#define AT91_PIN_PD9 (PIN_BASE + 0x60 + 9) + +#define AT91_PIN_PD10 (PIN_BASE + 0x60 + 10) +#define AT91_PIN_PD11 (PIN_BASE + 0x60 + 11) +#define AT91_PIN_PD12 (PIN_BASE + 0x60 + 12) +#define AT91_PIN_PD13 (PIN_BASE + 0x60 + 13) +#define AT91_PIN_PD14 (PIN_BASE + 0x60 + 14) + +#define AT91_PIN_PD15 (PIN_BASE + 0x60 + 15) +#define AT91_PIN_PD16 (PIN_BASE + 0x60 + 16) +#define AT91_PIN_PD17 (PIN_BASE + 0x60 + 17) +#define AT91_PIN_PD18 (PIN_BASE + 0x60 + 18) +#define AT91_PIN_PD19 (PIN_BASE + 0x60 + 19) + +#define AT91_PIN_PD20 (PIN_BASE + 0x60 + 20) +#define AT91_PIN_PD21 (PIN_BASE + 0x60 + 21) +#define AT91_PIN_PD22 (PIN_BASE + 0x60 + 22) +#define AT91_PIN_PD23 (PIN_BASE + 0x60 + 23) +#define AT91_PIN_PD24 (PIN_BASE + 0x60 + 24) + +#define AT91_PIN_PD25 (PIN_BASE + 0x60 + 25) +#define AT91_PIN_PD26 (PIN_BASE + 0x60 + 26) +#define AT91_PIN_PD27 (PIN_BASE + 0x60 + 27) +#define AT91_PIN_PD28 (PIN_BASE + 0x60 + 28) +#define AT91_PIN_PD29 (PIN_BASE + 0x60 + 29) + +#define AT91_PIN_PD30 (PIN_BASE + 0x60 + 30) +#define AT91_PIN_PD31 (PIN_BASE + 0x60 + 31) + +#ifndef __ASSEMBLY__ +/* setup setup routines, called from board init or driver probe() */ +extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_gpio_output(unsigned pin, int value); +extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on); +extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on); + +/* callable at any time */ +extern int at91_set_gpio_value(unsigned pin, int value); +extern int at91_get_gpio_value(unsigned pin); + +/* callable only from core power-management code */ +extern void at91_gpio_suspend(void); +extern void at91_gpio_resume(void); +#endif + +#endif + diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h new file mode 100644 index 000000000000..ccb7c7285b42 --- /dev/null +++ b/include/asm-arm/arch-at91/hardware.h @@ -0,0 +1,88 @@ +/* + * include/asm-arm/arch-at91/hardware.h + * + * Copyright (C) 2003 SAN People + * Copyright (C) 2003 ATMEL + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include + +#if defined(CONFIG_ARCH_AT91RM9200) +#include +#elif defined(CONFIG_ARCH_AT91SAM9260) +#include +#elif defined(CONFIG_ARCH_AT91SAM9261) +#include +#else +#error "Unsupported AT91 processor" +#endif + + +/* + * Remap the peripherals from address 0xFFFA0000 .. 0xFFFFFFFF + * to 0xFEFA0000 .. 0xFF000000. (384Kb) + */ +#define AT91_IO_PHYS_BASE 0xFFFA0000 +#define AT91_IO_SIZE (0xFFFFFFFF - AT91_IO_PHYS_BASE + 1) +#define AT91_IO_VIRT_BASE (0xFF000000 - AT91_IO_SIZE) + + /* Convert a physical IO address to virtual IO address */ +#define AT91_IO_P2V(x) ((x) - AT91_IO_PHYS_BASE + AT91_IO_VIRT_BASE) + +/* + * Virtual to Physical Address mapping for IO devices. + */ +#define AT91_VA_BASE_SYS AT91_IO_P2V(AT91_BASE_SYS) +#define AT91_VA_BASE_EMAC AT91_IO_P2V(AT91RM9200_BASE_EMAC) + + /* Internal SRAM is mapped below the IO devices */ +#define AT91_SRAM_MAX SZ_1M +#define AT91_VIRT_BASE (AT91_IO_VIRT_BASE - AT91_SRAM_MAX) + +/* Serial ports */ +#define ATMEL_MAX_UART 7 /* 6 USART3's and one DBGU port (SAM9260) */ + +/* External Memory Map */ +#define AT91_CHIPSELECT_0 0x10000000 +#define AT91_CHIPSELECT_1 0x20000000 +#define AT91_CHIPSELECT_2 0x30000000 +#define AT91_CHIPSELECT_3 0x40000000 +#define AT91_CHIPSELECT_4 0x50000000 +#define AT91_CHIPSELECT_5 0x60000000 +#define AT91_CHIPSELECT_6 0x70000000 +#define AT91_CHIPSELECT_7 0x80000000 + +/* SDRAM */ +#define AT91_SDRAM_BASE AT91_CHIPSELECT_1 + +/* Clocks */ +#define AT91_SLOW_CLOCK 32768 /* slow clock */ + +#ifndef __ASSEMBLY__ +#include + +static inline unsigned int at91_sys_read(unsigned int reg_offset) +{ + void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS; + + return __raw_readl(addr + reg_offset); +} + +static inline void at91_sys_write(unsigned int reg_offset, unsigned long value) +{ + void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS; + + __raw_writel(value, addr + reg_offset); +} +#endif + +#endif diff --git a/include/asm-arm/arch-at91/io.h b/include/asm-arm/arch-at91/io.h new file mode 100644 index 000000000000..401f327ec047 --- /dev/null +++ b/include/asm-arm/arch-at91/io.h @@ -0,0 +1,32 @@ +/* + * include/asm-arm/arch-at91/io.h + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include + +#define IO_SPACE_LIMIT 0xFFFFFFFF + +#define __io(a) ((void __iomem *)(a)) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-at91/irqs.h b/include/asm-arm/arch-at91/irqs.h new file mode 100644 index 000000000000..f041c98c5337 --- /dev/null +++ b/include/asm-arm/arch-at91/irqs.h @@ -0,0 +1,44 @@ +/* + * include/asm-arm/arch-at91/irqs.h + * + * Copyright (C) 2004 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include + +#define NR_AIC_IRQS 32 + + +/* + * Acknowledge interrupt with AIC after interrupt has been handled. + * (by kernel/irq.c) + */ +#define irq_finish(irq) do { at91_sys_write(AT91_AIC_EOICR, 0); } while (0) + + +/* + * IRQ interrupt symbols are the AT91xxx_ID_* symbols + * for IRQs handled directly through the AIC, or else the AT91_PIN_* + * symbols in gpio.h for ones handled indirectly as GPIOs. + * We make provision for 4 banks of GPIO. + */ +#define NR_IRQS (NR_AIC_IRQS + (4 * 32)) + +#endif diff --git a/include/asm-arm/arch-at91/memory.h b/include/asm-arm/arch-at91/memory.h new file mode 100644 index 000000000000..4835d6784509 --- /dev/null +++ b/include/asm-arm/arch-at91/memory.h @@ -0,0 +1,39 @@ +/* + * include/asm-arm/arch-at91/memory.h + * + * Copyright (C) 2004 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#include + +#define PHYS_OFFSET (AT91_SDRAM_BASE) + + +/* + * Virtual view <-> DMA view memory address translations + * virt_to_bus: Used to translate the virtual address to an + * address suitable to be passed to set_dma_addr + * bus_to_virt: Used to convert an address for DMA operations + * to an address that the kernel can use. + */ +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + +#endif diff --git a/include/asm-arm/arch-at91/system.h b/include/asm-arm/arch-at91/system.h new file mode 100644 index 000000000000..6bf846098ea9 --- /dev/null +++ b/include/asm-arm/arch-at91/system.h @@ -0,0 +1,53 @@ +/* + * include/asm-arm/arch-at91/system.h + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include +#include +#include + +static inline void arch_idle(void) +{ + /* + * Disable the processor clock. The processor will be automatically + * re-enabled by an interrupt or by a reset. + */ +// at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK); + + /* + * Set the processor (CP15) into 'Wait for Interrupt' mode. + * Unlike disabling the processor clock via the PMC (above) + * this allows the processor to be woken via JTAG. + */ + cpu_do_idle(); +} + +void (*at91_arch_reset)(void); + +static inline void arch_reset(char mode) +{ + /* call the CPU-specific reset function */ + if (at91_arch_reset) + (at91_arch_reset)(); +} + +#endif diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h new file mode 100644 index 000000000000..b24e364997e1 --- /dev/null +++ b/include/asm-arm/arch-at91/timex.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-at91/timex.h + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_TIMEX_H +#define __ASM_ARCH_TIMEX_H + +#include + +#if defined(CONFIG_ARCH_AT91RM9200) + +#define CLOCK_TICK_RATE (AT91_SLOW_CLOCK) + +#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) + +#define AT91SAM9_MASTER_CLOCK 99300000 +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + +#endif + +#endif diff --git a/include/asm-arm/arch-at91/uncompress.h b/include/asm-arm/arch-at91/uncompress.h new file mode 100644 index 000000000000..a193d28304b6 --- /dev/null +++ b/include/asm-arm/arch-at91/uncompress.h @@ -0,0 +1,56 @@ +/* + * include/asm-arm/arch-at91/uncompress.h + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_UNCOMPRESS_H +#define __ASM_ARCH_UNCOMPRESS_H + +#include +#include + +/* + * The following code assumes the serial port has already been + * initialized by the bootloader. If you didn't setup a port in + * your bootloader then nothing will appear (which might be desired). + * + * This does not append a newline + */ +static void putc(int c) +{ + void __iomem *sys = (void __iomem *) AT91_BASE_SYS; /* physical address */ + + while (!(__raw_readl(sys + AT91_DBGU_SR) & AT91_DBGU_TXRDY)) + barrier(); + __raw_writel(c, sys + AT91_DBGU_THR); +} + +static inline void flush(void) +{ + void __iomem *sys = (void __iomem *) AT91_BASE_SYS; /* physical address */ + + /* wait for transmission to complete */ + while (!(__raw_readl(sys + AT91_DBGU_SR) & AT91_DBGU_TXEMPTY)) + barrier(); +} + +#define arch_decomp_setup() + +#define arch_decomp_wdog() + +#endif diff --git a/include/asm-arm/arch-at91/vmalloc.h b/include/asm-arm/arch-at91/vmalloc.h new file mode 100644 index 000000000000..bb05e70e932a --- /dev/null +++ b/include/asm-arm/arch-at91/vmalloc.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-at91/vmalloc.h + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_VMALLOC_H +#define __ASM_ARCH_VMALLOC_H + +#define VMALLOC_END (AT91_VIRT_BASE & PGDIR_MASK) + +#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_aic.h b/include/asm-arm/arch-at91rm9200/at91_aic.h deleted file mode 100644 index 267e69812e26..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_aic.h +++ /dev/null @@ -1,53 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_aic.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Advanced Interrupt Controller (AIC) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_AIC_H -#define AT91_AIC_H - -#define AT91_AIC_SMR(n) (AT91_AIC + ((n) * 4)) /* Source Mode Registers 0-31 */ -#define AT91_AIC_PRIOR (7 << 0) /* Priority Level */ -#define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */ -#define AT91_AIC_SRCTYPE_LOW (0 << 5) -#define AT91_AIC_SRCTYPE_FALLING (1 << 5) -#define AT91_AIC_SRCTYPE_HIGH (2 << 5) -#define AT91_AIC_SRCTYPE_RISING (3 << 5) - -#define AT91_AIC_SVR(n) (AT91_AIC + 0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */ -#define AT91_AIC_IVR (AT91_AIC + 0x100) /* Interrupt Vector Register */ -#define AT91_AIC_FVR (AT91_AIC + 0x104) /* Fast Interrupt Vector Register */ -#define AT91_AIC_ISR (AT91_AIC + 0x108) /* Interrupt Status Register */ -#define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */ - -#define AT91_AIC_IPR (AT91_AIC + 0x10c) /* Interrupt Pending Register */ -#define AT91_AIC_IMR (AT91_AIC + 0x110) /* Interrupt Mask Register */ -#define AT91_AIC_CISR (AT91_AIC + 0x114) /* Core Interrupt Status Register */ -#define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */ -#define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */ - -#define AT91_AIC_IECR (AT91_AIC + 0x120) /* Interrupt Enable Command Register */ -#define AT91_AIC_IDCR (AT91_AIC + 0x124) /* Interrupt Disable Command Register */ -#define AT91_AIC_ICCR (AT91_AIC + 0x128) /* Interrupt Clear Command Register */ -#define AT91_AIC_ISCR (AT91_AIC + 0x12c) /* Interrupt Set Command Register */ -#define AT91_AIC_EOICR (AT91_AIC + 0x130) /* End of Interrupt Command Register */ -#define AT91_AIC_SPU (AT91_AIC + 0x134) /* Spurious Interrupt Vector Register */ -#define AT91_AIC_DCR (AT91_AIC + 0x138) /* Debug Control Register */ -#define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */ -#define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */ - -#define AT91_AIC_FFER (AT91_AIC + 0x140) /* Fast Forcing Enable Register [SAM9 only] */ -#define AT91_AIC_FFDR (AT91_AIC + 0x144) /* Fast Forcing Disable Register [SAM9 only] */ -#define AT91_AIC_FFSR (AT91_AIC + 0x148) /* Fast Forcing Status Register [SAM9 only] */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_dbgu.h b/include/asm-arm/arch-at91rm9200/at91_dbgu.h deleted file mode 100644 index e4b8b27acfca..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_dbgu.h +++ /dev/null @@ -1,45 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_dbgu.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Debug Unit (DBGU) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_DBGU_H -#define AT91_DBGU_H - -#define AT91_DBGU_CR (AT91_DBGU + 0x00) /* Control Register */ -#define AT91_DBGU_MR (AT91_DBGU + 0x04) /* Mode Register */ -#define AT91_DBGU_IER (AT91_DBGU + 0x08) /* Interrupt Enable Register */ -#define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */ -#define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */ -#define AT91_DBGU_IDR (AT91_DBGU + 0x0c) /* Interrupt Disable Register */ -#define AT91_DBGU_IMR (AT91_DBGU + 0x10) /* Interrupt Mask Register */ -#define AT91_DBGU_SR (AT91_DBGU + 0x14) /* Status Register */ -#define AT91_DBGU_RHR (AT91_DBGU + 0x18) /* Receiver Holding Register */ -#define AT91_DBGU_THR (AT91_DBGU + 0x1c) /* Transmitter Holding Register */ -#define AT91_DBGU_BRGR (AT91_DBGU + 0x20) /* Baud Rate Generator Register */ - -#define AT91_DBGU_CIDR (AT91_DBGU + 0x40) /* Chip ID Register */ -#define AT91_DBGU_EXID (AT91_DBGU + 0x44) /* Chip ID Extension Register */ -#define AT91_CIDR_VERSION (0x1f << 0) /* Version of the Device */ -#define AT91_CIDR_EPROC (7 << 5) /* Embedded Processor */ -#define AT91_CIDR_NVPSIZ (0xf << 8) /* Nonvolatile Program Memory Size */ -#define AT91_CIDR_NVPSIZ2 (0xf << 12) /* Second Nonvolatile Program Memory Size */ -#define AT91_CIDR_SRAMSIZ (0xf << 16) /* Internal SRAM Size */ -#define AT91_CIDR_ARCH (0xff << 20) /* Architecture Identifier */ -#define AT91_CIDR_NVPTYP (7 << 28) /* Nonvolatile Program Memory Type */ -#define AT91_CIDR_EXT (1 << 31) /* Extension Flag */ - -#define AT91_DBGU_FNR (AT91_DBGU + 0x48) /* Force NTRST Register [SAM9 only] */ -#define AT91_DBGU_FNTRST (1 << 0) /* Force NTRST */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_ecc.h b/include/asm-arm/arch-at91rm9200/at91_ecc.h deleted file mode 100644 index 5c564ede5c5d..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_ecc.h +++ /dev/null @@ -1,38 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_ecc.h - * - * Error Corrected Code Controller (ECC) - System peripherals regsters. - * Based on AT91SAM9260 datasheet revision B. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#ifndef AT91_ECC_H -#define AT91_ECC_H - -#define AT91_ECC_CR (AT91_ECC + 0x00) /* Control register */ -#define AT91_ECC_RST (1 << 0) /* Reset parity */ - -#define AT91_ECC_MR (AT91_ECC + 0x04) /* Mode register */ -#define AT91_ECC_PAGESIZE (3 << 0) /* Page Size */ -#define AT91_ECC_PAGESIZE_528 (0) -#define AT91_ECC_PAGESIZE_1056 (1) -#define AT91_ECC_PAGESIZE_2112 (2) -#define AT91_ECC_PAGESIZE_4224 (3) - -#define AT91_ECC_SR (AT91_ECC + 0x08) /* Status register */ -#define AT91_ECC_RECERR (1 << 0) /* Recoverable Error */ -#define AT91_ECC_ECCERR (1 << 1) /* ECC Single Bit Error */ -#define AT91_ECC_MULERR (1 << 2) /* Multiple Errors */ - -#define AT91_ECC_PR (AT91_ECC + 0x0c) /* Parity register */ -#define AT91_ECC_BITADDR (0xf << 0) /* Bit Error Address */ -#define AT91_ECC_WORDADDR (0xfff << 4) /* Word Error Address */ - -#define AT91_ECC_NPR (AT91_ECC + 0x10) /* NParity register */ -#define AT91_ECC_NPARITY (0xffff << 0) /* NParity */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_lcdc.h b/include/asm-arm/arch-at91rm9200/at91_lcdc.h deleted file mode 100644 index 9cbfcdd3c471..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_lcdc.h +++ /dev/null @@ -1,148 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_lcdc.h - * - * LCD Controller (LCDC). - * Based on AT91SAM9261 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_LCDC_H -#define AT91_LCDC_H - -#define AT91_LCDC_DMABADDR1 0x00 /* DMA Base Address Register 1 */ -#define AT91_LCDC_DMABADDR2 0x04 /* DMA Base Address Register 2 */ -#define AT91_LCDC_DMAFRMPT1 0x08 /* DMA Frame Pointer Register 1 */ -#define AT91_LCDC_DMAFRMPT2 0x0c /* DMA Frame Pointer Register 2 */ -#define AT91_LCDC_DMAFRMADD1 0x10 /* DMA Frame Address Register 1 */ -#define AT91_LCDC_DMAFRMADD2 0x14 /* DMA Frame Address Register 2 */ - -#define AT91_LCDC_DMAFRMCFG 0x18 /* DMA Frame Configuration Register */ -#define AT91_LCDC_FRSIZE (0x7fffff << 0) /* Frame Size */ -#define AT91_LCDC_BLENGTH (0x7f << 24) /* Burst Length */ - -#define AT91_LCDC_DMACON 0x1c /* DMA Control Register */ -#define AT91_LCDC_DMAEN (0x1 << 0) /* DMA Enable */ -#define AT91_LCDC_DMARST (0x1 << 1) /* DMA Reset */ -#define AT91_LCDC_DMABUSY (0x1 << 2) /* DMA Busy */ - -#define AT91_LCDC_LCDCON1 0x0800 /* LCD Control Register 1 */ -#define AT91_LCDC_BYPASS (1 << 0) /* Bypass lcd_dotck divider */ -#define AT91_LCDC_CLKVAL (0x1ff << 12) /* Clock Divider */ -#define AT91_LCDC_LINCNT (0x7ff << 21) /* Line Counter */ - -#define AT91_LCDC_LCDCON2 0x0804 /* LCD Control Register 2 */ -#define AT91_LCDC_DISTYPE (3 << 0) /* Display Type */ -#define AT91_LCDC_DISTYPE_STNMONO (0 << 0) -#define AT91_LCDC_DISTYPE_STNCOLOR (1 << 0) -#define AT91_LCDC_DISTYPE_TFT (2 << 0) -#define AT91_LCDC_SCANMOD (1 << 2) /* Scan Mode */ -#define AT91_LCDC_SCANMOD_SINGLE (0 << 2) -#define AT91_LCDC_SCANMOD_DUAL (1 << 2) -#define AT91_LCDC_IFWIDTH (3 << 3) /*Interface Width */ -#define AT91_LCDC_IFWIDTH_4 (0 << 3) -#define AT91_LCDC_IFWIDTH_8 (1 << 3) -#define AT91_LCDC_IFWIDTH_16 (2 << 3) -#define AT91_LCDC_PIXELSIZE (7 << 5) /* Bits per pixel */ -#define AT91_LCDC_PIXELSIZE_1 (0 << 5) -#define AT91_LCDC_PIXELSIZE_2 (1 << 5) -#define AT91_LCDC_PIXELSIZE_4 (2 << 5) -#define AT91_LCDC_PIXELSIZE_8 (3 << 5) -#define AT91_LCDC_PIXELSIZE_16 (4 << 5) -#define AT91_LCDC_PIXELSIZE_24 (5 << 5) -#define AT91_LCDC_INVVD (1 << 8) /* LCD Data polarity */ -#define AT91_LCDC_INVVD_NORMAL (0 << 8) -#define AT91_LCDC_INVVD_INVERTED (1 << 8) -#define AT91_LCDC_INVFRAME (1 << 9 ) /* LCD VSync polarity */ -#define AT91_LCDC_INVFRAME_NORMAL (0 << 9) -#define AT91_LCDC_INVFRAME_INVERTED (1 << 9) -#define AT91_LCDC_INVLINE (1 << 10) /* LCD HSync polarity */ -#define AT91_LCDC_INVLINE_NORMAL (0 << 10) -#define AT91_LCDC_INVLINE_INVERTED (1 << 10) -#define AT91_LCDC_INVCLK (1 << 11) /* LCD dotclk polarity */ -#define AT91_LCDC_INVCLK_NORMAL (0 << 11) -#define AT91_LCDC_INVCLK_INVERTED (1 << 11) -#define AT91_LCDC_INVDVAL (1 << 12) /* LCD dval polarity */ -#define AT91_LCDC_INVDVAL_NORMAL (0 << 12) -#define AT91_LCDC_INVDVAL_INVERTED (1 << 12) -#define AT91_LCDC_CLKMOD (1 << 15) /* LCD dotclk mode */ -#define AT91_LCDC_CLKMOD_ACTIVEDISPLAY (0 << 15) -#define AT91_LCDC_CLKMOD_ALWAYSACTIVE (1 << 15) -#define AT91_LCDC_MEMOR (1 << 31) /* Memory Ordering Format */ -#define AT91_LCDC_MEMOR_BIG (0 << 31) -#define AT91_LCDC_MEMOR_LITTLE (1 << 31) - -#define AT91_LCDC_TIM1 0x0808 /* LCD Timing Register 1 */ -#define AT91_LCDC_VFP (0xff << 0) /* Vertical Front Porch */ -#define AT91_LCDC_VBP (0xff << 8) /* Vertical Back Porch */ -#define AT91_LCDC_VPW (0x3f << 16) /* Vertical Synchronization Pulse Width */ -#define AT91_LCDC_VHDLY (0xf << 24) /* Vertical to Horizontal Delay */ - -#define AT91_LCDC_TIM2 0x080c /* LCD Timing Register 2 */ -#define AT91_LCDC_HBP (0xff << 0) /* Horizontal Back Porch */ -#define AT91_LCDC_HPW (0x3f << 8) /* Horizontal Synchronization Pulse Width */ -#define AT91_LCDC_HFP (0x7ff << 21) /* Horizontal Front Porch */ - -#define AT91_LCDC_LCDFRMCFG 0x0810 /* LCD Frame Configuration Register */ -#define AT91_LCDC_LINEVAL (0x7ff << 0) /* Vertical Size of LCD Module */ -#define AT91_LCDC_HOZVAL (0x7ff << 21) /* Horizontal Size of LCD Module */ - -#define AT91_LCDC_FIFO 0x0814 /* LCD FIFO Register */ -#define AT91_LCDC_FIFOTH (0xffff) /* FIFO Threshold */ - -#define AT91_LCDC_DP1_2 0x081c /* Dithering Pattern DP1_2 Register */ -#define AT91_LCDC_DP4_7 0x0820 /* Dithering Pattern DP4_7 Register */ -#define AT91_LCDC_DP3_5 0x0824 /* Dithering Pattern DP3_5 Register */ -#define AT91_LCDC_DP2_3 0x0828 /* Dithering Pattern DP2_3 Register */ -#define AT91_LCDC_DP5_7 0x082c /* Dithering Pattern DP5_7 Register */ -#define AT91_LCDC_DP3_4 0x0830 /* Dithering Pattern DP3_4 Register */ -#define AT91_LCDC_DP4_5 0x0834 /* Dithering Pattern DP4_5 Register */ -#define AT91_LCDC_DP6_7 0x0838 /* Dithering Pattern DP6_7 Register */ -#define AT91_LCDC_DP1_2_VAL (0xff) -#define AT91_LCDC_DP4_7_VAL (0xfffffff) -#define AT91_LCDC_DP3_5_VAL (0xfffff) -#define AT91_LCDC_DP2_3_VAL (0xfff) -#define AT91_LCDC_DP5_7_VAL (0xfffffff) -#define AT91_LCDC_DP3_4_VAL (0xffff) -#define AT91_LCDC_DP4_5_VAL (0xfffff) -#define AT91_LCDC_DP6_7_VAL (0xfffffff) - -#define AT91_LCDC_PWRCON 0x083c /* Power Control Register */ -#define AT91_LCDC_PWR (1 << 0) /* LCD Module Power Control */ -#define AT91_LCDC_GUARDT (0x7f << 1) /* Delay in Frame Period */ -#define AT91_LCDC_BUSY (1 << 31) /* LCD Busy */ - -#define AT91_LCDC_CONTRAST_CTR 0x0840 /* Contrast Control Register */ -#define AT91_LCDC_PS (3 << 0) /* Contrast Counter Prescaler */ -#define AT91_LCDC_PS_DIV1 (0 << 0) -#define AT91_LCDC_PS_DIV2 (1 << 0) -#define AT91_LCDC_PS_DIV4 (2 << 0) -#define AT91_LCDC_PS_DIV8 (3 << 0) -#define AT91_LCDC_POL (1 << 2) /* Polarity of output Pulse */ -#define AT91_LCDC_POL_NEGATIVE (0 << 2) -#define AT91_LCDC_POL_POSITIVE (1 << 2) -#define AT91_LCDC_ENA (1 << 3) /* PWM generator Control */ -#define AT91_LCDC_ENA_PWMDISABLE (0 << 3) -#define AT91_LCDC_ENA_PWMENABLE (1 << 3) - -#define AT91_LCDC_CONTRAST_VAL 0x0844 /* Contrast Value Register */ -#define AT91_LCDC_CVAL (0xff) /* PWM compare value */ - -#define AT91_LCDC_IER 0x0848 /* Interrupt Enable Register */ -#define AT91_LCDC_IDR 0x084c /* Interrupt Disable Register */ -#define AT91_LCDC_IMR 0x0850 /* Interrupt Mask Register */ -#define AT91_LCDC_ISR 0x0854 /* Interrupt Enable Register */ -#define AT91_LCDC_ICR 0x0858 /* Interrupt Clear Register */ -#define AT91_LCDC_LNI (1 << 0) /* Line Interrupt */ -#define AT91_LCDC_LSTLNI (1 << 1) /* Last Line Interrupt */ -#define AT91_LCDC_EOFI (1 << 2) /* DMA End Of Frame Interrupt */ -#define AT91_LCDC_UFLWI (1 << 4) /* FIFO Underflow Interrupt */ -#define AT91_LCDC_OWRI (1 << 5) /* FIFO Overwrite Interrupt */ -#define AT91_LCDC_MERI (1 << 6) /* DMA Memory Error Interrupt */ - -#define AT91_LCDC_LUT_(n) (0x0c00 + ((n)*4)) /* Palette Entry 0..255 */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_mci.h b/include/asm-arm/arch-at91rm9200/at91_mci.h deleted file mode 100644 index 9a552cb743c0..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_mci.h +++ /dev/null @@ -1,106 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_mci.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * MultiMedia Card Interface (MCI) registers. - * Based on AT91RM9200 datasheet revision F. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_MCI_H -#define AT91_MCI_H - -#define AT91_MCI_CR 0x00 /* Control Register */ -#define AT91_MCI_MCIEN (1 << 0) /* Multi-Media Interface Enable */ -#define AT91_MCI_MCIDIS (1 << 1) /* Multi-Media Interface Disable */ -#define AT91_MCI_PWSEN (1 << 2) /* Power Save Mode Enable */ -#define AT91_MCI_PWSDIS (1 << 3) /* Power Save Mode Disable */ -#define AT91_MCI_SWRST (1 << 7) /* Software Reset */ - -#define AT91_MCI_MR 0x04 /* Mode Register */ -#define AT91_MCI_CLKDIV (0xff << 0) /* Clock Divider */ -#define AT91_MCI_PWSDIV (7 << 8) /* Power Saving Divider */ -#define AT91_MCI_PDCPADV (1 << 14) /* PDC Padding Value */ -#define AT91_MCI_PDCMODE (1 << 15) /* PDC-orientated Mode */ -#define AT91_MCI_BLKLEN (0xfff << 18) /* Data Block Length */ - -#define AT91_MCI_DTOR 0x08 /* Data Timeout Register */ -#define AT91_MCI_DTOCYC (0xf << 0) /* Data Timeout Cycle Number */ -#define AT91_MCI_DTOMUL (7 << 4) /* Data Timeout Multiplier */ -#define AT91_MCI_DTOMUL_1 (0 << 4) -#define AT91_MCI_DTOMUL_16 (1 << 4) -#define AT91_MCI_DTOMUL_128 (2 << 4) -#define AT91_MCI_DTOMUL_256 (3 << 4) -#define AT91_MCI_DTOMUL_1K (4 << 4) -#define AT91_MCI_DTOMUL_4K (5 << 4) -#define AT91_MCI_DTOMUL_64K (6 << 4) -#define AT91_MCI_DTOMUL_1M (7 << 4) - -#define AT91_MCI_SDCR 0x0c /* SD Card Register */ -#define AT91_MCI_SDCSEL (3 << 0) /* SD Card Selector */ -#define AT91_MCI_SDCBUS (1 << 7) /* 1-bit or 4-bit bus */ - -#define AT91_MCI_ARGR 0x10 /* Argument Register */ - -#define AT91_MCI_CMDR 0x14 /* Command Register */ -#define AT91_MCI_CMDNB (0x3f << 0) /* Command Number */ -#define AT91_MCI_RSPTYP (3 << 6) /* Response Type */ -#define AT91_MCI_RSPTYP_NONE (0 << 6) -#define AT91_MCI_RSPTYP_48 (1 << 6) -#define AT91_MCI_RSPTYP_136 (2 << 6) -#define AT91_MCI_SPCMD (7 << 8) /* Special Command */ -#define AT91_MCI_SPCMD_NONE (0 << 8) -#define AT91_MCI_SPCMD_INIT (1 << 8) -#define AT91_MCI_SPCMD_SYNC (2 << 8) -#define AT91_MCI_SPCMD_ICMD (4 << 8) -#define AT91_MCI_SPCMD_IRESP (5 << 8) -#define AT91_MCI_OPDCMD (1 << 11) /* Open Drain Command */ -#define AT91_MCI_MAXLAT (1 << 12) /* Max Latency for Command to Response */ -#define AT91_MCI_TRCMD (3 << 16) /* Transfer Command */ -#define AT91_MCI_TRCMD_NONE (0 << 16) -#define AT91_MCI_TRCMD_START (1 << 16) -#define AT91_MCI_TRCMD_STOP (2 << 16) -#define AT91_MCI_TRDIR (1 << 18) /* Transfer Direction */ -#define AT91_MCI_TRTYP (3 << 19) /* Transfer Type */ -#define AT91_MCI_TRTYP_BLOCK (0 << 19) -#define AT91_MCI_TRTYP_MULTIPLE (1 << 19) -#define AT91_MCI_TRTYP_STREAM (2 << 19) - -#define AT91_MCI_RSPR(n) (0x20 + ((n) * 4)) /* Response Registers 0-3 */ -#define AT91_MCR_RDR 0x30 /* Receive Data Register */ -#define AT91_MCR_TDR 0x34 /* Transmit Data Register */ - -#define AT91_MCI_SR 0x40 /* Status Register */ -#define AT91_MCI_CMDRDY (1 << 0) /* Command Ready */ -#define AT91_MCI_RXRDY (1 << 1) /* Receiver Ready */ -#define AT91_MCI_TXRDY (1 << 2) /* Transmit Ready */ -#define AT91_MCI_BLKE (1 << 3) /* Data Block Ended */ -#define AT91_MCI_DTIP (1 << 4) /* Data Transfer in Progress */ -#define AT91_MCI_NOTBUSY (1 << 5) /* Data Not Busy */ -#define AT91_MCI_ENDRX (1 << 6) /* End of RX Buffer */ -#define AT91_MCI_ENDTX (1 << 7) /* End fo TX Buffer */ -#define AT91_MCI_SDIOIRQA (1 << 8) /* SDIO Interrupt for Slot A */ -#define At91_MCI_SDIOIRQB (1 << 9) /* SDIO Interrupt for Slot B [AT91RM9200 only] */ -#define AT91_MCI_RXBUFF (1 << 14) /* RX Buffer Full */ -#define AT91_MCI_TXBUFE (1 << 15) /* TX Buffer Empty */ -#define AT91_MCI_RINDE (1 << 16) /* Response Index Error */ -#define AT91_MCI_RDIRE (1 << 17) /* Response Direction Error */ -#define AT91_MCI_RCRCE (1 << 18) /* Response CRC Error */ -#define AT91_MCI_RENDE (1 << 19) /* Response End Bit Error */ -#define AT91_MCI_RTOE (1 << 20) /* Reponse Time-out Error */ -#define AT91_MCI_DCRCE (1 << 21) /* Data CRC Error */ -#define AT91_MCI_DTOE (1 << 22) /* Data Time-out Error */ -#define AT91_MCI_OVRE (1 << 30) /* Overrun */ -#define AT91_MCI_UNRE (1 << 31) /* Underrun */ - -#define AT91_MCI_IER 0x44 /* Interrupt Enable Register */ -#define AT91_MCI_IDR 0x48 /* Interrupt Disable Register */ -#define AT91_MCI_IMR 0x4c /* Interrupt Mask Register */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_pdc.h b/include/asm-arm/arch-at91rm9200/at91_pdc.h deleted file mode 100644 index 79d6e02fa45e..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_pdc.h +++ /dev/null @@ -1,36 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_pdc.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Peripheral Data Controller (PDC) registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_PDC_H -#define AT91_PDC_H - -#define AT91_PDC_RPR 0x100 /* Receive Pointer Register */ -#define AT91_PDC_RCR 0x104 /* Receive Counter Register */ -#define AT91_PDC_TPR 0x108 /* Transmit Pointer Register */ -#define AT91_PDC_TCR 0x10c /* Transmit Counter Register */ -#define AT91_PDC_RNPR 0x110 /* Receive Next Pointer Register */ -#define AT91_PDC_RNCR 0x114 /* Receive Next Counter Register */ -#define AT91_PDC_TNPR 0x118 /* Transmit Next Pointer Register */ -#define AT91_PDC_TNCR 0x11c /* Transmit Next Counter Register */ - -#define AT91_PDC_PTCR 0x120 /* Transfer Control Register */ -#define AT91_PDC_RXTEN (1 << 0) /* Receiver Transfer Enable */ -#define AT91_PDC_RXTDIS (1 << 1) /* Receiver Transfer Disable */ -#define AT91_PDC_TXTEN (1 << 8) /* Transmitter Transfer Enable */ -#define AT91_PDC_TXTDIS (1 << 9) /* Transmitter Transfer Disable */ - -#define AT91_PDC_PTSR 0x124 /* Transfer Status Register */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_pio.h b/include/asm-arm/arch-at91rm9200/at91_pio.h deleted file mode 100644 index 680eaa1f5915..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_pio.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_pio.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Parallel I/O Controller (PIO) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_PIO_H -#define AT91_PIO_H - -#define PIO_PER 0x00 /* Enable Register */ -#define PIO_PDR 0x04 /* Disable Register */ -#define PIO_PSR 0x08 /* Status Register */ -#define PIO_OER 0x10 /* Output Enable Register */ -#define PIO_ODR 0x14 /* Output Disable Register */ -#define PIO_OSR 0x18 /* Output Status Register */ -#define PIO_IFER 0x20 /* Glitch Input Filter Enable */ -#define PIO_IFDR 0x24 /* Glitch Input Filter Disable */ -#define PIO_IFSR 0x28 /* Glitch Input Filter Status */ -#define PIO_SODR 0x30 /* Set Output Data Register */ -#define PIO_CODR 0x34 /* Clear Output Data Register */ -#define PIO_ODSR 0x38 /* Output Data Status Register */ -#define PIO_PDSR 0x3c /* Pin Data Status Register */ -#define PIO_IER 0x40 /* Interrupt Enable Register */ -#define PIO_IDR 0x44 /* Interrupt Disable Register */ -#define PIO_IMR 0x48 /* Interrupt Mask Register */ -#define PIO_ISR 0x4c /* Interrupt Status Register */ -#define PIO_MDER 0x50 /* Multi-driver Enable Register */ -#define PIO_MDDR 0x54 /* Multi-driver Disable Register */ -#define PIO_MDSR 0x58 /* Multi-driver Status Register */ -#define PIO_PUDR 0x60 /* Pull-up Disable Register */ -#define PIO_PUER 0x64 /* Pull-up Enable Register */ -#define PIO_PUSR 0x68 /* Pull-up Status Register */ -#define PIO_ASR 0x70 /* Peripheral A Select Register */ -#define PIO_BSR 0x74 /* Peripheral B Select Register */ -#define PIO_ABSR 0x78 /* AB Status Register */ -#define PIO_OWER 0xa0 /* Output Write Enable Register */ -#define PIO_OWDR 0xa4 /* Output Write Disable Register */ -#define PIO_OWSR 0xa8 /* Output Write Status Register */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_pit.h b/include/asm-arm/arch-at91rm9200/at91_pit.h deleted file mode 100644 index 4a30d009c588..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_pit.h +++ /dev/null @@ -1,29 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_pit.h - * - * Periodic Interval Timer (PIT) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_PIT_H -#define AT91_PIT_H - -#define AT91_PIT_MR (AT91_PIT + 0x00) /* Mode Register */ -#define AT91_PIT_PITIEN (1 << 25) /* Timer Interrupt Enable */ -#define AT91_PIT_PITEN (1 << 24) /* Timer Enabled */ -#define AT91_PIT_PIV (0xfffff) /* Periodic Interval Value */ - -#define AT91_PIT_SR (AT91_PIT + 0x04) /* Status Register */ -#define AT91_PIT_PITS (1 << 0) /* Timer Status */ - -#define AT91_PIT_PIVR (AT91_PIT + 0x08) /* Periodic Interval Value Register */ -#define AT91_PIT_PIIR (AT91_PIT + 0x0c) /* Periodic Interval Image Register */ -#define AT91_PIT_PICNT (0xfff << 20) /* Interval Counter */ -#define AT91_PIT_CPIV (0xfffff) /* Inverval Value */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_pmc.h b/include/asm-arm/arch-at91rm9200/at91_pmc.h deleted file mode 100644 index c3b489d09b6c..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_pmc.h +++ /dev/null @@ -1,92 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_pmc.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Power Management Controller (PMC) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_PMC_H -#define AT91_PMC_H - -#define AT91_PMC_SCER (AT91_PMC + 0x00) /* System Clock Enable Register */ -#define AT91_PMC_SCDR (AT91_PMC + 0x04) /* System Clock Disable Register */ - -#define AT91_PMC_SCSR (AT91_PMC + 0x08) /* System Clock Status Register */ -#define AT91_PMC_PCK (1 << 0) /* Processor Clock */ -#define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */ -#define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */ -#define AT91RM9200_PMC_UHP (1 << 4) /* USB Host Port Clock [AT91RM9200 only] */ -#define AT91SAM926x_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91SAM926x only] */ -#define AT91SAM926x_PMC_UDP (1 << 7) /* USB Devcice Port Clock [AT91SAM926x only] */ -#define AT91_PMC_PCK0 (1 << 8) /* Programmable Clock 0 */ -#define AT91_PMC_PCK1 (1 << 9) /* Programmable Clock 1 */ -#define AT91_PMC_PCK2 (1 << 10) /* Programmable Clock 2 */ -#define AT91_PMC_PCK3 (1 << 11) /* Programmable Clock 3 */ -#define AT91_PMC_HCK0 (1 << 16) /* AHB Clock (USB host) [AT91SAM9261 only] */ -#define AT91_PMC_HCK1 (1 << 17) /* AHB Clock (LCD) [AT91SAM9261 only] */ - -#define AT91_PMC_PCER (AT91_PMC + 0x10) /* Peripheral Clock Enable Register */ -#define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */ -#define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */ - -#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register */ -#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ -#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */ -#define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ - -#define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */ -#define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */ -#define AT91_PMC_MAINRDY (1 << 16) /* Main Clock Ready */ - -#define AT91_CKGR_PLLAR (AT91_PMC + 0x28) /* PLL A Register */ -#define AT91_CKGR_PLLBR (AT91_PMC + 0x2c) /* PLL B Register */ -#define AT91_PMC_DIV (0xff << 0) /* Divider */ -#define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */ -#define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */ -#define AT91_PMC_MUL (0x7ff << 16) /* PLL Multiplier */ -#define AT91_PMC_USB96M (1 << 28) /* Divider by 2 Enable (PLLB only) */ - -#define AT91_PMC_MCKR (AT91_PMC + 0x30) /* Master Clock Register */ -#define AT91_PMC_CSS (3 << 0) /* Master Clock Selection */ -#define AT91_PMC_CSS_SLOW (0 << 0) -#define AT91_PMC_CSS_MAIN (1 << 0) -#define AT91_PMC_CSS_PLLA (2 << 0) -#define AT91_PMC_CSS_PLLB (3 << 0) -#define AT91_PMC_PRES (7 << 2) /* Master Clock Prescaler */ -#define AT91_PMC_PRES_1 (0 << 2) -#define AT91_PMC_PRES_2 (1 << 2) -#define AT91_PMC_PRES_4 (2 << 2) -#define AT91_PMC_PRES_8 (3 << 2) -#define AT91_PMC_PRES_16 (4 << 2) -#define AT91_PMC_PRES_32 (5 << 2) -#define AT91_PMC_PRES_64 (6 << 2) -#define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */ -#define AT91_PMC_MDIV_1 (0 << 8) -#define AT91_PMC_MDIV_2 (1 << 8) -#define AT91_PMC_MDIV_3 (2 << 8) -#define AT91_PMC_MDIV_4 (3 << 8) - -#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-3 Registers */ - -#define AT91_PMC_IER (AT91_PMC + 0x60) /* Interrupt Enable Register */ -#define AT91_PMC_IDR (AT91_PMC + 0x64) /* Interrupt Disable Register */ -#define AT91_PMC_SR (AT91_PMC + 0x68) /* Status Register */ -#define AT91_PMC_MOSCS (1 << 0) /* MOSCS Flag */ -#define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */ -#define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */ -#define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */ -#define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */ -#define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */ -#define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */ -#define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */ -#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_rstc.h b/include/asm-arm/arch-at91rm9200/at91_rstc.h deleted file mode 100644 index 237d3c40b318..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_rstc.h +++ /dev/null @@ -1,39 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_rstc.h - * - * Reset Controller (RSTC) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_RSTC_H -#define AT91_RSTC_H - -#define AT91_RSTC_CR (AT91_RSTC + 0x00) /* Reset Controller Control Register */ -#define AT91_RSTC_PROCRST (1 << 0) /* Processor Reset */ -#define AT91_RSTC_PERRST (1 << 2) /* Peripheral Reset */ -#define AT91_RSTC_EXTRST (1 << 3) /* External Reset */ -#define AT91_RSTC_KEY (0xff << 24) /* KEY Password */ - -#define AT91_RSTC_SR (AT91_RSTC + 0x04) /* Reset Controller Status Register */ -#define AT91_RSTC_URSTS (1 << 0) /* User Reset Status */ -#define AT91_RSTC_RSTTYP (7 << 8) /* Reset Type */ -#define AT91_RSTC_RSTTYP_GENERAL (0 << 8) -#define AT91_RSTC_RSTTYP_WAKEUP (1 << 8) -#define AT91_RSTC_RSTTYP_WATCHDOG (2 << 8) -#define AT91_RSTC_RSTTYP_SOFTWARE (3 << 8) -#define AT91_RSTC_RSTTYP_USER (4 << 8) -#define AT91_RSTC_NRSTL (1 << 16) /* NRST Pin Level */ -#define AT91_RSTC_SRCMP (1 << 17) /* Software Reset Command in Progress */ - -#define AT91_RSTC_MR (AT91_RSTC + 0x08) /* Reset Controller Mode Register */ -#define AT91_RSTC_URSTEN (1 << 0) /* User Reset Enable */ -#define AT91_RSTC_URSTIEN (1 << 4) /* User Reset Interrupt Enable */ -#define AT91_RSTC_ERSTL (0xf << 8) /* External Reset Length */ -#define AT91_RSTC_KEY (0xff << 24) /* KEY Password */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_rtc.h b/include/asm-arm/arch-at91rm9200/at91_rtc.h deleted file mode 100644 index 095fe0883102..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_rtc.h +++ /dev/null @@ -1,75 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_rtc.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Real Time Clock (RTC) - System peripheral registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_RTC_H -#define AT91_RTC_H - -#define AT91_RTC_CR (AT91_RTC + 0x00) /* Control Register */ -#define AT91_RTC_UPDTIM (1 << 0) /* Update Request Time Register */ -#define AT91_RTC_UPDCAL (1 << 1) /* Update Request Calendar Register */ -#define AT91_RTC_TIMEVSEL (3 << 8) /* Time Event Selection */ -#define AT91_RTC_TIMEVSEL_MINUTE (0 << 8) -#define AT91_RTC_TIMEVSEL_HOUR (1 << 8) -#define AT91_RTC_TIMEVSEL_DAY24 (2 << 8) -#define AT91_RTC_TIMEVSEL_DAY12 (3 << 8) -#define AT91_RTC_CALEVSEL (3 << 16) /* Calendar Event Selection */ -#define AT91_RTC_CALEVSEL_WEEK (0 << 16) -#define AT91_RTC_CALEVSEL_MONTH (1 << 16) -#define AT91_RTC_CALEVSEL_YEAR (2 << 16) - -#define AT91_RTC_MR (AT91_RTC + 0x04) /* Mode Register */ -#define AT91_RTC_HRMOD (1 << 0) /* 12/24 Hour Mode */ - -#define AT91_RTC_TIMR (AT91_RTC + 0x08) /* Time Register */ -#define AT91_RTC_SEC (0x7f << 0) /* Current Second */ -#define AT91_RTC_MIN (0x7f << 8) /* Current Minute */ -#define AT91_RTC_HOUR (0x3f << 16) /* Current Hour */ -#define AT91_RTC_AMPM (1 << 22) /* Ante Meridiem Post Meridiem Indicator */ - -#define AT91_RTC_CALR (AT91_RTC + 0x0c) /* Calendar Register */ -#define AT91_RTC_CENT (0x7f << 0) /* Current Century */ -#define AT91_RTC_YEAR (0xff << 8) /* Current Year */ -#define AT91_RTC_MONTH (0x1f << 16) /* Current Month */ -#define AT91_RTC_DAY (7 << 21) /* Current Day */ -#define AT91_RTC_DATE (0x3f << 24) /* Current Date */ - -#define AT91_RTC_TIMALR (AT91_RTC + 0x10) /* Time Alarm Register */ -#define AT91_RTC_SECEN (1 << 7) /* Second Alarm Enable */ -#define AT91_RTC_MINEN (1 << 15) /* Minute Alarm Enable */ -#define AT91_RTC_HOUREN (1 << 23) /* Hour Alarm Enable */ - -#define AT91_RTC_CALALR (AT91_RTC + 0x14) /* Calendar Alarm Register */ -#define AT91_RTC_MTHEN (1 << 23) /* Month Alarm Enable */ -#define AT91_RTC_DATEEN (1 << 31) /* Date Alarm Enable */ - -#define AT91_RTC_SR (AT91_RTC + 0x18) /* Status Register */ -#define AT91_RTC_ACKUPD (1 << 0) /* Acknowledge for Update */ -#define AT91_RTC_ALARM (1 << 1) /* Alarm Flag */ -#define AT91_RTC_SECEV (1 << 2) /* Second Event */ -#define AT91_RTC_TIMEV (1 << 3) /* Time Event */ -#define AT91_RTC_CALEV (1 << 4) /* Calendar Event */ - -#define AT91_RTC_SCCR (AT91_RTC + 0x1c) /* Status Clear Command Register */ -#define AT91_RTC_IER (AT91_RTC + 0x20) /* Interrupt Enable Register */ -#define AT91_RTC_IDR (AT91_RTC + 0x24) /* Interrupt Disable Register */ -#define AT91_RTC_IMR (AT91_RTC + 0x28) /* Interrupt Mask Register */ - -#define AT91_RTC_VER (AT91_RTC + 0x2c) /* Valid Entry Register */ -#define AT91_RTC_NVTIM (1 << 0) /* Non valid Time */ -#define AT91_RTC_NVCAL (1 << 1) /* Non valid Calendar */ -#define AT91_RTC_NVTIMALR (1 << 2) /* Non valid Time Alarm */ -#define AT91_RTC_NVCALALR (1 << 3) /* Non valid Calendar Alarm */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_rtt.h b/include/asm-arm/arch-at91rm9200/at91_rtt.h deleted file mode 100644 index c6751ba3cccc..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_rtt.h +++ /dev/null @@ -1,32 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_rtt.h - * - * Real-time Timer (RTT) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_RTT_H -#define AT91_RTT_H - -#define AT91_RTT_MR (AT91_RTT + 0x00) /* Real-time Mode Register */ -#define AT91_RTT_RTPRES (0xffff << 0) /* Real-time Timer Prescaler Value */ -#define AT91_RTT_ALMIEN (1 << 16) /* Alarm Interrupt Enable */ -#define AT91_RTT_RTTINCIEN (1 << 17) /* Real Time Timer Increment Interrupt Enable */ -#define AT91_RTT_RTTRST (1 << 18) /* Real Time Timer Restart */ - -#define AT91_RTT_AR (AT91_RTT + 0x04) /* Real-time Alarm Register */ -#define AT91_RTT_ALMV (0xffffffff) /* Alarm Value */ - -#define AT91_RTT_VR (AT91_RTT + 0x08) /* Real-time Value Register */ -#define AT91_RTT_CRTV (0xffffffff) /* Current Real-time Value */ - -#define AT91_RTT_SR (AT91_RTT + 0x0c) /* Real-time Status Register */ -#define AT91_RTT_ALMS (1 << 0) /* Real-time Alarm Status */ -#define AT91_RTT_RTTINC (1 << 1) /* Real-time Timer Increment */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_shdwc.h b/include/asm-arm/arch-at91rm9200/at91_shdwc.h deleted file mode 100644 index 0439250553c9..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_shdwc.h +++ /dev/null @@ -1,33 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_shdwc.h - * - * Shutdown Controller (SHDWC) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_SHDWC_H -#define AT91_SHDWC_H - -#define AT91_SHDW_CR (AT91_SHDWC + 0x00) /* Shut Down Control Register */ -#define AT91_SHDW_SHDW (1 << 0) /* Processor Reset */ -#define AT91_SHDW_KEY (0xff << 24) /* KEY Password */ - -#define AT91_SHDW_MR (AT91_SHDWC + 0x04) /* Shut Down Mode Register */ -#define AT91_SHDW_WKMODE0 (3 << 0) /* Wake-up 0 Mode Selection */ -#define AT91_SHDW_WKMODE0_NONE 0 -#define AT91_SHDW_WKMODE0_HIGH 1 -#define AT91_SHDW_WKMODE0_LOW 2 -#define AT91_SHDW_WKMODE0_ANYLEVEL 3 -#define AT91_SHDW_CPTWK0 (0xf << 4) /* Counter On Wake Up 0 */ -#define AT91_SHDW_RTTWKEN (1 << 16) /* Real Time Timer Wake-up Enable */ - -#define AT91_SHDW_SR (AT91_SHDWC + 0x08) /* Shut Down Status Register */ -#define AT91_SHDW_WAKEUP0 (1 << 0) /* Wake-up 0 Status */ -#define AT91_SHDW_RTTWK (1 << 16) /* Real-time Timer Wake-up */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_spi.h b/include/asm-arm/arch-at91rm9200/at91_spi.h deleted file mode 100644 index bec48ca89bba..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_spi.h +++ /dev/null @@ -1,81 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_spi.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Serial Peripheral Interface (SPI) registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_SPI_H -#define AT91_SPI_H - -#define AT91_SPI_CR 0x00 /* Control Register */ -#define AT91_SPI_SPIEN (1 << 0) /* SPI Enable */ -#define AT91_SPI_SPIDIS (1 << 1) /* SPI Disable */ -#define AT91_SPI_SWRST (1 << 7) /* SPI Software Reset */ -#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */ - -#define AT91_SPI_MR 0x04 /* Mode Register */ -#define AT91_SPI_MSTR (1 << 0) /* Master/Slave Mode */ -#define AT91_SPI_PS (1 << 1) /* Peripheral Select */ -#define AT91_SPI_PS_FIXED (0 << 1) -#define AT91_SPI_PS_VARIABLE (1 << 1) -#define AT91_SPI_PCSDEC (1 << 2) /* Chip Select Decode */ -#define AT91_SPI_DIV32 (1 << 3) /* Clock Selection [AT91RM9200 only] */ -#define AT91_SPI_MODFDIS (1 << 4) /* Mode Fault Detection */ -#define AT91_SPI_LLB (1 << 7) /* Local Loopback Enable */ -#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ -#define AT91_SPI_DLYBCS (0xff << 24) /* Delay Between Chip Selects */ - -#define AT91_SPI_RDR 0x08 /* Receive Data Register */ -#define AT91_SPI_RD (0xffff << 0) /* Receive Data */ -#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ - -#define AT91_SPI_TDR 0x0c /* Transmit Data Register */ -#define AT91_SPI_TD (0xffff << 0) /* Transmit Data */ -#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ -#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */ - -#define AT91_SPI_SR 0x10 /* Status Register */ -#define AT91_SPI_RDRF (1 << 0) /* Receive Data Register Full */ -#define AT91_SPI_TDRE (1 << 1) /* Transmit Data Register Full */ -#define AT91_SPI_MODF (1 << 2) /* Mode Fault Error */ -#define AT91_SPI_OVRES (1 << 3) /* Overrun Error Status */ -#define AT91_SPI_ENDRX (1 << 4) /* End of RX buffer */ -#define AT91_SPI_ENDTX (1 << 5) /* End of TX buffer */ -#define AT91_SPI_RXBUFF (1 << 6) /* RX Buffer Full */ -#define AT91_SPI_TXBUFE (1 << 7) /* TX Buffer Empty */ -#define AT91_SPI_NSSR (1 << 8) /* NSS Rising [SAM9261 only] */ -#define AT91_SPI_TXEMPTY (1 << 9) /* Transmission Register Empty [SAM9261 only] */ -#define AT91_SPI_SPIENS (1 << 16) /* SPI Enable Status */ - -#define AT91_SPI_IER 0x14 /* Interrupt Enable Register */ -#define AT91_SPI_IDR 0x18 /* Interrupt Disable Register */ -#define AT91_SPI_IMR 0x1c /* Interrupt Mask Register */ - -#define AT91_SPI_CSR(n) (0x30 + ((n) * 4)) /* Chip Select Registers 0-3 */ -#define AT91_SPI_CPOL (1 << 0) /* Clock Polarity */ -#define AT91_SPI_NCPHA (1 << 1) /* Clock Phase */ -#define AT91_SPI_CSAAT (1 << 3) /* Chip Select Active After Transfer [SAM9261 only] */ -#define AT91_SPI_BITS (0xf << 4) /* Bits Per Transfer */ -#define AT91_SPI_BITS_8 (0 << 4) -#define AT91_SPI_BITS_9 (1 << 4) -#define AT91_SPI_BITS_10 (2 << 4) -#define AT91_SPI_BITS_11 (3 << 4) -#define AT91_SPI_BITS_12 (4 << 4) -#define AT91_SPI_BITS_13 (5 << 4) -#define AT91_SPI_BITS_14 (6 << 4) -#define AT91_SPI_BITS_15 (7 << 4) -#define AT91_SPI_BITS_16 (8 << 4) -#define AT91_SPI_SCBR (0xff << 8) /* Serial Clock Baud Rate */ -#define AT91_SPI_DLYBS (0xff << 16) /* Delay before SPCK */ -#define AT91_SPI_DLYBCT (0xff << 24) /* Delay between Consecutive Transfers */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_ssc.h b/include/asm-arm/arch-at91rm9200/at91_ssc.h deleted file mode 100644 index 694bcaa8f7c2..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_ssc.h +++ /dev/null @@ -1,106 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_ssc.h - * - * Copyright (C) SAN People - * - * Serial Synchronous Controller (SSC) registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_SSC_H -#define AT91_SSC_H - -#define AT91_SSC_CR 0x00 /* Control Register */ -#define AT91_SSC_RXEN (1 << 0) /* Receive Enable */ -#define AT91_SSC_RXDIS (1 << 1) /* Receive Disable */ -#define AT91_SSC_TXEN (1 << 8) /* Transmit Enable */ -#define AT91_SSC_TXDIS (1 << 9) /* Transmit Disable */ -#define AT91_SSC_SWRST (1 << 15) /* Software Reset */ - -#define AT91_SSC_CMR 0x04 /* Clock Mode Register */ -#define AT91_SSC_CMR_DIV (0xfff << 0) /* Clock Divider */ - -#define AT91_SSC_RCMR 0x10 /* Receive Clock Mode Register */ -#define AT91_SSC_CKS (3 << 0) /* Clock Selection */ -#define AT91_SSC_CKS_DIV (0 << 0) -#define AT91_SSC_CKS_CLOCK (1 << 0) -#define AT91_SSC_CKS_PIN (2 << 0) -#define AT91_SSC_CKO (7 << 2) /* Clock Output Mode Selection */ -#define AT91_SSC_CKO_NONE (0 << 2) -#define AT91_SSC_CKO_CONTINUOUS (1 << 2) -#define AT91_SSC_CKI (1 << 5) /* Clock Inversion */ -#define AT91_SSC_CKI_FALLING (0 << 5) -#define AT91_SSC_CK_RISING (1 << 5) -#define AT91_SSC_CKG (1 << 6) /* Receive Clock Gating Selection [AT91SAM9261 only] */ -#define AT91_SSC_CKG_NONE (0 << 6) -#define AT91_SSC_CKG_RFLOW (1 << 6) -#define AT91_SSC_CKG_RFHIGH (2 << 6) -#define AT91_SSC_START (0xf << 8) /* Start Selection */ -#define AT91_SSC_START_CONTINUOUS (0 << 8) -#define AT91_SSC_START_TX_RX (1 << 8) -#define AT91_SSC_START_LOW_RF (2 << 8) -#define AT91_SSC_START_HIGH_RF (3 << 8) -#define AT91_SSC_START_FALLING_RF (4 << 8) -#define AT91_SSC_START_RISING_RF (5 << 8) -#define AT91_SSC_START_LEVEL_RF (6 << 8) -#define AT91_SSC_START_EDGE_RF (7 << 8) -#define AT91_SSC_STOP (1 << 12) /* Receive Stop Selection [AT91SAM9261 only] */ -#define AT91_SSC_STTDLY (0xff << 16) /* Start Delay */ -#define AT91_SSC_PERIOD (0xff << 24) /* Period Divider Selection */ - -#define AT91_SSC_RFMR 0x14 /* Receive Frame Mode Register */ -#define AT91_SSC_DATALEN (0x1f << 0) /* Data Length */ -#define AT91_SSC_LOOP (1 << 5) /* Loop Mode */ -#define AT91_SSC_MSBF (1 << 7) /* Most Significant Bit First */ -#define AT91_SSC_DATNB (0xf << 8) /* Data Number per Frame */ -#define AT91_SSC_FSLEN (0xf << 16) /* Frame Sync Length */ -#define AT91_SSC_FSOS (7 << 20) /* Frame Sync Output Selection */ -#define AT91_SSC_FSOS_NONE (0 << 20) -#define AT91_SSC_FSOS_NEGATIVE (1 << 20) -#define AT91_SSC_FSOS_POSITIVE (2 << 20) -#define AT91_SSC_FSOS_LOW (3 << 20) -#define AT91_SSC_FSOS_HIGH (4 << 20) -#define AT91_SSC_FSOS_TOGGLE (5 << 20) -#define AT91_SSC_FSEDGE (1 << 24) /* Frame Sync Edge Detection */ -#define AT91_SSC_FSEDGE_POSITIVE (0 << 24) -#define AT91_SSC_FSEDGE_NEGATIVE (1 << 24) - -#define AT91_SSC_TCMR 0x18 /* Transmit Clock Mode Register */ -#define AT91_SSC_TFMR 0x1c /* Transmit Fram Mode Register */ -#define AT91_SSC_DATDEF (1 << 5) /* Data Default Value */ -#define AT91_SSC_FSDEN (1 << 23) /* Frame Sync Data Enable */ - -#define AT91_SSC_RHR 0x20 /* Receive Holding Register */ -#define AT91_SSC_THR 0x24 /* Transmit Holding Register */ -#define AT91_SSC_RSHR 0x30 /* Receive Sync Holding Register */ -#define AT91_SSC_TSHR 0x34 /* Transmit Sync Holding Register */ - -#define AT91_SSC_RC0R 0x38 /* Receive Compare 0 Register [AT91SAM9261 only] */ -#define AT91_SSC_RC1R 0x3c /* Receive Compare 1 Register [AT91SAM9261 only] */ - -#define AT91_SSC_SR 0x40 /* Status Register */ -#define AT91_SSC_TXRDY (1 << 0) /* Transmit Ready */ -#define AT91_SSC_TXEMPTY (1 << 1) /* Transmit Empty */ -#define AT91_SSC_ENDTX (1 << 2) /* End of Transmission */ -#define AT91_SSC_TXBUFE (1 << 3) /* Transmit Buffer Empty */ -#define AT91_SSC_RXRDY (1 << 4) /* Receive Ready */ -#define AT91_SSC_OVRUN (1 << 5) /* Receive Overrun */ -#define AT91_SSC_ENDRX (1 << 6) /* End of Reception */ -#define AT91_SSC_RXBUFF (1 << 7) /* Receive Buffer Full */ -#define AT91_SSC_CP0 (1 << 8) /* Compare 0 [AT91SAM9261 only] */ -#define AT91_SSC_CP1 (1 << 9) /* Compare 1 [AT91SAM9261 only] */ -#define AT91_SSC_TXSYN (1 << 10) /* Transmit Sync */ -#define AT91_SSC_RXSYN (1 << 11) /* Receive Sync */ -#define AT91_SSC_TXENA (1 << 16) /* Transmit Enable */ -#define AT91_SSC_RXENA (1 << 17) /* Receive Enable */ - -#define AT91_SSC_IER 0x44 /* Interrupt Enable Register */ -#define AT91_SSC_IDR 0x48 /* Interrupt Disable Register */ -#define AT91_SSC_IMR 0x4c /* Interrupt Mask Register */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_st.h b/include/asm-arm/arch-at91rm9200/at91_st.h deleted file mode 100644 index 2432ddfc6c47..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_st.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_st.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * System Timer (ST) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_ST_H -#define AT91_ST_H - -#define AT91_ST_CR (AT91_ST + 0x00) /* Control Register */ -#define AT91_ST_WDRST (1 << 0) /* Watchdog Timer Restart */ - -#define AT91_ST_PIMR (AT91_ST + 0x04) /* Period Interval Mode Register */ -#define AT91_ST_PIV (0xffff << 0) /* Period Interval Value */ - -#define AT91_ST_WDMR (AT91_ST + 0x08) /* Watchdog Mode Register */ -#define AT91_ST_WDV (0xffff << 0) /* Watchdog Counter Value */ -#define AT91_ST_RSTEN (1 << 16) /* Reset Enable */ -#define AT91_ST_EXTEN (1 << 17) /* External Signal Assertion Enable */ - -#define AT91_ST_RTMR (AT91_ST + 0x0c) /* Real-time Mode Register */ -#define AT91_ST_RTPRES (0xffff << 0) /* Real-time Prescalar Value */ - -#define AT91_ST_SR (AT91_ST + 0x10) /* Status Register */ -#define AT91_ST_PITS (1 << 0) /* Period Interval Timer Status */ -#define AT91_ST_WDOVF (1 << 1) /* Watchdog Overflow */ -#define AT91_ST_RTTINC (1 << 2) /* Real-time Timer Increment */ -#define AT91_ST_ALMS (1 << 3) /* Alarm Status */ - -#define AT91_ST_IER (AT91_ST + 0x14) /* Interrupt Enable Register */ -#define AT91_ST_IDR (AT91_ST + 0x18) /* Interrupt Disable Register */ -#define AT91_ST_IMR (AT91_ST + 0x1c) /* Interrupt Mask Register */ - -#define AT91_ST_RTAR (AT91_ST + 0x20) /* Real-time Alarm Register */ -#define AT91_ST_ALMV (0xfffff << 0) /* Alarm Value */ - -#define AT91_ST_CRTR (AT91_ST + 0x24) /* Current Real-time Register */ -#define AT91_ST_CRTV (0xfffff << 0) /* Current Real-Time Value */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_tc.h b/include/asm-arm/arch-at91rm9200/at91_tc.h deleted file mode 100644 index 8d06eb078e1d..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_tc.h +++ /dev/null @@ -1,146 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_tc.h - * - * Copyright (C) SAN People - * - * Timer/Counter Unit (TC) registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_TC_H -#define AT91_TC_H - -#define AT91_TC_BCR 0xc0 /* TC Block Control Register */ -#define AT91_TC_SYNC (1 << 0) /* Synchro Command */ - -#define AT91_TC_BMR 0xc4 /* TC Block Mode Register */ -#define AT91_TC_TC0XC0S (3 << 0) /* External Clock Signal 0 Selection */ -#define AT91_TC_TC0XC0S_TCLK0 (0 << 0) -#define AT91_TC_TC0XC0S_NONE (1 << 0) -#define AT91_TC_TC0XC0S_TIOA1 (2 << 0) -#define AT91_TC_TC0XC0S_TIOA2 (3 << 0) -#define AT91_TC_TC1XC1S (3 << 2) /* External Clock Signal 1 Selection */ -#define AT91_TC_TC1XC1S_TCLK1 (0 << 2) -#define AT91_TC_TC1XC1S_NONE (1 << 2) -#define AT91_TC_TC1XC1S_TIOA0 (2 << 2) -#define AT91_TC_TC1XC1S_TIOA2 (3 << 2) -#define AT91_TC_TC2XC2S (3 << 4) /* External Clock Signal 2 Selection */ -#define AT91_TC_TC2XC2S_TCLK2 (0 << 4) -#define AT91_TC_TC2XC2S_NONE (1 << 4) -#define AT91_TC_TC2XC2S_TIOA0 (2 << 4) -#define AT91_TC_TC2XC2S_TIOA1 (3 << 4) - - -#define AT91_TC_CCR 0x00 /* Channel Control Register */ -#define AT91_TC_CLKEN (1 << 0) /* Counter Clock Enable Command */ -#define AT91_TC_CLKDIS (1 << 1) /* Counter CLock Disable Command */ -#define AT91_TC_SWTRG (1 << 2) /* Software Trigger Command */ - -#define AT91_TC_CMR 0x04 /* Channel Mode Register */ -#define AT91_TC_TCCLKS (7 << 0) /* Capture/Waveform Mode: Clock Selection */ -#define AT91_TC_TIMER_CLOCK1 (0 << 0) -#define AT91_TC_TIMER_CLOCK2 (1 << 0) -#define AT91_TC_TIMER_CLOCK3 (2 << 0) -#define AT91_TC_TIMER_CLOCK4 (3 << 0) -#define AT91_TC_TIMER_CLOCK5 (4 << 0) -#define AT91_TC_XC0 (5 << 0) -#define AT91_TC_XC1 (6 << 0) -#define AT91_TC_XC2 (7 << 0) -#define AT91_TC_CLKI (1 << 3) /* Capture/Waveform Mode: Clock Invert */ -#define AT91_TC_BURST (3 << 4) /* Capture/Waveform Mode: Burst Signal Selection */ -#define AT91_TC_LDBSTOP (1 << 6) /* Capture Mode: Counter Clock Stopped with TB Loading */ -#define AT91_TC_LDBDIS (1 << 7) /* Capture Mode: Counter Clock Disable with RB Loading */ -#define AT91_TC_ETRGEDG (3 << 8) /* Capture Mode: External Trigger Edge Selection */ -#define AT91_TC_ABETRG (1 << 10) /* Capture Mode: TIOA or TIOB External Trigger Selection */ -#define AT91_TC_CPCTRG (1 << 14) /* Capture Mode: RC Compare Trigger Enable */ -#define AT91_TC_WAVE (1 << 15) /* Capture/Waveform mode */ -#define AT91_TC_LDRA (3 << 16) /* Capture Mode: RA Loading Selection */ -#define AT91_TC_LDRB (3 << 18) /* Capture Mode: RB Loading Selection */ - -#define AT91_TC_CPCSTOP (1 << 6) /* Waveform Mode: Counter Clock Stopped with RC Compare */ -#define AT91_TC_CPCDIS (1 << 7) /* Waveform Mode: Counter Clock Disable with RC Compare */ -#define AT91_TC_EEVTEDG (3 << 8) /* Waveform Mode: External Event Edge Selection */ -#define AT91_TC_EEVTEDG_NONE (0 << 8) -#define AT91_TC_EEVTEDG_RISING (1 << 8) -#define AT91_TC_EEVTEDG_FALLING (2 << 8) -#define AT91_TC_EEVTEDG_BOTH (3 << 8) -#define AT91_TC_EEVT (3 << 10) /* Waveform Mode: External Event Selection */ -#define AT91_TC_EEVT_TIOB (0 << 10) -#define AT91_TC_EEVT_XC0 (1 << 10) -#define AT91_TC_EEVT_XC1 (2 << 10) -#define AT91_TC_EEVT_XC2 (3 << 10) -#define AT91_TC_ENETRG (1 << 12) /* Waveform Mode: External Event Trigger Enable */ -#define AT91_TC_WAVESEL (3 << 13) /* Waveform Mode: Waveform Selection */ -#define AT91_TC_WAVESEL_UP (0 << 13) -#define AT91_TC_WAVESEL_UP_AUTO (2 << 13) -#define AT91_TC_WAVESEL_UPDOWN (1 << 13) -#define AT91_TC_WAVESEL_UPDOWN_AUTO (3 << 13) -#define AT91_TC_ACPA (3 << 16) /* Waveform Mode: RA Compare Effect on TIOA */ -#define AT91_TC_ACPA_NONE (0 << 16) -#define AT91_TC_ACPA_SET (1 << 16) -#define AT91_TC_ACPA_CLEAR (2 << 16) -#define AT91_TC_ACPA_TOGGLE (3 << 16) -#define AT91_TC_ACPC (3 << 18) /* Waveform Mode: RC Compre Effect on TIOA */ -#define AT91_TC_ACPC_NONE (0 << 18) -#define AT91_TC_ACPC_SET (1 << 18) -#define AT91_TC_ACPC_CLEAR (2 << 18) -#define AT91_TC_ACPC_TOGGLE (3 << 18) -#define AT91_TC_AEEVT (3 << 20) /* Waveform Mode: External Event Effect on TIOA */ -#define AT91_TC_AEEVT_NONE (0 << 20) -#define AT91_TC_AEEVT_SET (1 << 20) -#define AT91_TC_AEEVT_CLEAR (2 << 20) -#define AT91_TC_AEEVT_TOGGLE (3 << 20) -#define AT91_TC_ASWTRG (3 << 22) /* Waveform Mode: Software Trigger Effect on TIOA */ -#define AT91_TC_ASWTRG_NONE (0 << 22) -#define AT91_TC_ASWTRG_SET (1 << 22) -#define AT91_TC_ASWTRG_CLEAR (2 << 22) -#define AT91_TC_ASWTRG_TOGGLE (3 << 22) -#define AT91_TC_BCPB (3 << 24) /* Waveform Mode: RB Compare Effect on TIOB */ -#define AT91_TC_BCPB_NONE (0 << 24) -#define AT91_TC_BCPB_SET (1 << 24) -#define AT91_TC_BCPB_CLEAR (2 << 24) -#define AT91_TC_BCPB_TOGGLE (3 << 24) -#define AT91_TC_BCPC (3 << 26) /* Waveform Mode: RC Compare Effect on TIOB */ -#define AT91_TC_BCPC_NONE (0 << 26) -#define AT91_TC_BCPC_SET (1 << 26) -#define AT91_TC_BCPC_CLEAR (2 << 26) -#define AT91_TC_BCPC_TOGGLE (3 << 26) -#define AT91_TC_BEEVT (3 << 28) /* Waveform Mode: External Event Effect on TIOB */ -#define AT91_TC_BEEVT_NONE (0 << 28) -#define AT91_TC_BEEVT_SET (1 << 28) -#define AT91_TC_BEEVT_CLEAR (2 << 28) -#define AT91_TC_BEEVT_TOGGLE (3 << 28) -#define AT91_TC_BSWTRG (3 << 30) /* Waveform Mode: Software Trigger Effect on TIOB */ -#define AT91_TC_BSWTRG_NONE (0 << 30) -#define AT91_TC_BSWTRG_SET (1 << 30) -#define AT91_TC_BSWTRG_CLEAR (2 << 30) -#define AT91_TC_BSWTRG_TOGGLE (3 << 30) - -#define AT91_TC_CV 0x10 /* Counter Value */ -#define AT91_TC_RA 0x14 /* Register A */ -#define AT91_TC_RB 0x18 /* Register B */ -#define AT91_TC_RC 0x1c /* Register C */ - -#define AT91_TC_SR 0x20 /* Status Register */ -#define AT91_TC_COVFS (1 << 0) /* Counter Overflow Status */ -#define AT91_TC_LOVRS (1 << 1) /* Load Overrun Status */ -#define AT91_TC_CPAS (1 << 2) /* RA Compare Status */ -#define AT91_TC_CPBS (1 << 3) /* RB Compare Status */ -#define AT91_TC_CPCS (1 << 4) /* RC Compare Status */ -#define AT91_TC_LDRAS (1 << 5) /* RA Loading Status */ -#define AT91_TC_LDRBS (1 << 6) /* RB Loading Status */ -#define AT91_TC_ETRGS (1 << 7) /* External Trigger Status */ -#define AT91_TC_CLKSTA (1 << 16) /* Clock Enabling Status */ -#define AT91_TC_MTIOA (1 << 17) /* TIOA Mirror */ -#define AT91_TC_MTIOB (1 << 18) /* TIOB Mirror */ - -#define AT91_TC_IER 0x24 /* Interrupt Enable Register */ -#define AT91_TC_IDR 0x28 /* Interrupt Disable Register */ -#define AT91_TC_IMR 0x2c /* Interrupt Mask Register */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91_twi.h b/include/asm-arm/arch-at91rm9200/at91_twi.h deleted file mode 100644 index cda914f1e740..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_twi.h +++ /dev/null @@ -1,57 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_twi.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Two-wire Interface (TWI) registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_TWI_H -#define AT91_TWI_H - -#define AT91_TWI_CR 0x00 /* Control Register */ -#define AT91_TWI_START (1 << 0) /* Send a Start Condition */ -#define AT91_TWI_STOP (1 << 1) /* Send a Stop Condition */ -#define AT91_TWI_MSEN (1 << 2) /* Master Transfer Enable */ -#define AT91_TWI_MSDIS (1 << 3) /* Master Transfer Disable */ -#define AT91_TWI_SWRST (1 << 7) /* Software Reset */ - -#define AT91_TWI_MMR 0x04 /* Master Mode Register */ -#define AT91_TWI_IADRSZ (3 << 8) /* Internal Device Address Size */ -#define AT91_TWI_IADRSZ_NO (0 << 8) -#define AT91_TWI_IADRSZ_1 (1 << 8) -#define AT91_TWI_IADRSZ_2 (2 << 8) -#define AT91_TWI_IADRSZ_3 (3 << 8) -#define AT91_TWI_MREAD (1 << 12) /* Master Read Direction */ -#define AT91_TWI_DADR (0x7f << 16) /* Device Address */ - -#define AT91_TWI_IADR 0x0c /* Internal Address Register */ - -#define AT91_TWI_CWGR 0x10 /* Clock Waveform Generator Register */ -#define AT91_TWI_CLDIV (0xff << 0) /* Clock Low Divisor */ -#define AT91_TWI_CHDIV (0xff << 8) /* Clock High Divisor */ -#define AT91_TWI_CKDIV (7 << 16) /* Clock Divider */ - -#define AT91_TWI_SR 0x20 /* Status Register */ -#define AT91_TWI_TXCOMP (1 << 0) /* Transmission Complete */ -#define AT91_TWI_RXRDY (1 << 1) /* Receive Holding Register Ready */ -#define AT91_TWI_TXRDY (1 << 2) /* Transmit Holding Register Ready */ -#define AT91_TWI_OVRE (1 << 6) /* Overrun Error [AT91RM9200 only] */ -#define AT91_TWI_UNRE (1 << 7) /* Underrun Error [AT91RM9200 only] */ -#define AT91_TWI_NACK (1 << 8) /* Not Acknowledged */ - -#define AT91_TWI_IER 0x24 /* Interrupt Enable Register */ -#define AT91_TWI_IDR 0x28 /* Interrupt Disable Register */ -#define AT91_TWI_IMR 0x2c /* Interrupt Mask Register */ -#define AT91_TWI_RHR 0x30 /* Receive Holding Register */ -#define AT91_TWI_THR 0x34 /* Transmit Holding Register */ - -#endif - diff --git a/include/asm-arm/arch-at91rm9200/at91_wdt.h b/include/asm-arm/arch-at91rm9200/at91_wdt.h deleted file mode 100644 index ac63e775772c..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91_wdt.h +++ /dev/null @@ -1,34 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91_wdt.h - * - * Watchdog Timer (WDT) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_WDT_H -#define AT91_WDT_H - -#define AT91_WDT_CR (AT91_WDT + 0x00) /* Watchdog Control Register */ -#define AT91_WDT_WDRSTT (1 << 0) /* Restart */ -#define AT91_WDT_KEY (0xff << 24) /* KEY Password */ - -#define AT91_WDT_MR (AT91_WDT + 0x04) /* Watchdog Mode Register */ -#define AT91_WDT_WDV (0xfff << 0) /* Counter Value */ -#define AT91_WDT_WDFIEN (1 << 12) /* Fault Interrupt Enable */ -#define AT91_WDT_WDRSTEN (1 << 13) /* Reset Processor */ -#define AT91_WDT_WDRPROC (1 << 14) /* Timer Restart */ -#define AT91_WDT_WDDIS (1 << 15) /* Watchdog Disable */ -#define AT91_WDT_WDD (0xfff << 16) /* Delta Value */ -#define AT91_WDT_WDDBGHLT (1 << 28) /* Debug Halt */ -#define AT91_WDT_WDIDLEHLT (1 << 29) /* Idle Halt */ - -#define AT91_WDT_SR (AT91_WDT + 0x08) /* Watchdog Status Register */ -#define AT91_WDT_WDUNF (1 << 0) /* Watchdog Underflow */ -#define AT91_WDT_WDERR (1 << 1) /* Watchdog Error */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200.h b/include/asm-arm/arch-at91rm9200/at91rm9200.h deleted file mode 100644 index c569b6a21a42..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91rm9200.h +++ /dev/null @@ -1,291 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91rm9200.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Common definitions. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91RM9200_H -#define AT91RM9200_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ -#define AT91_ID_SYS 1 /* System Peripheral */ -#define AT91RM9200_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91RM9200_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91RM9200_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91RM9200_ID_PIOD 5 /* Parallel IO Controller D */ -#define AT91RM9200_ID_US0 6 /* USART 0 */ -#define AT91RM9200_ID_US1 7 /* USART 1 */ -#define AT91RM9200_ID_US2 8 /* USART 2 */ -#define AT91RM9200_ID_US3 9 /* USART 3 */ -#define AT91RM9200_ID_MCI 10 /* Multimedia Card Interface */ -#define AT91RM9200_ID_UDP 11 /* USB Device Port */ -#define AT91RM9200_ID_TWI 12 /* Two-Wire Interface */ -#define AT91RM9200_ID_SPI 13 /* Serial Peripheral Interface */ -#define AT91RM9200_ID_SSC0 14 /* Serial Synchronous Controller 0 */ -#define AT91RM9200_ID_SSC1 15 /* Serial Synchronous Controller 1 */ -#define AT91RM9200_ID_SSC2 16 /* Serial Synchronous Controller 2 */ -#define AT91RM9200_ID_TC0 17 /* Timer Counter 0 */ -#define AT91RM9200_ID_TC1 18 /* Timer Counter 1 */ -#define AT91RM9200_ID_TC2 19 /* Timer Counter 2 */ -#define AT91RM9200_ID_TC3 20 /* Timer Counter 3 */ -#define AT91RM9200_ID_TC4 21 /* Timer Counter 4 */ -#define AT91RM9200_ID_TC5 22 /* Timer Counter 5 */ -#define AT91RM9200_ID_UHP 23 /* USB Host port */ -#define AT91RM9200_ID_EMAC 24 /* Ethernet MAC */ -#define AT91RM9200_ID_IRQ0 25 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91RM9200_ID_IRQ1 26 /* Advanced Interrupt Controller (IRQ1) */ -#define AT91RM9200_ID_IRQ2 27 /* Advanced Interrupt Controller (IRQ2) */ -#define AT91RM9200_ID_IRQ3 28 /* Advanced Interrupt Controller (IRQ3) */ -#define AT91RM9200_ID_IRQ4 29 /* Advanced Interrupt Controller (IRQ4) */ -#define AT91RM9200_ID_IRQ5 30 /* Advanced Interrupt Controller (IRQ5) */ -#define AT91RM9200_ID_IRQ6 31 /* Advanced Interrupt Controller (IRQ6) */ - - -/* - * Peripheral physical base addresses. - */ -#define AT91RM9200_BASE_TCB0 0xfffa0000 -#define AT91RM9200_BASE_TC0 0xfffa0000 -#define AT91RM9200_BASE_TC1 0xfffa0040 -#define AT91RM9200_BASE_TC2 0xfffa0080 -#define AT91RM9200_BASE_TCB1 0xfffa4000 -#define AT91RM9200_BASE_TC3 0xfffa4000 -#define AT91RM9200_BASE_TC4 0xfffa4040 -#define AT91RM9200_BASE_TC5 0xfffa4080 -#define AT91RM9200_BASE_UDP 0xfffb0000 -#define AT91RM9200_BASE_MCI 0xfffb4000 -#define AT91RM9200_BASE_TWI 0xfffb8000 -#define AT91RM9200_BASE_EMAC 0xfffbc000 -#define AT91RM9200_BASE_US0 0xfffc0000 -#define AT91RM9200_BASE_US1 0xfffc4000 -#define AT91RM9200_BASE_US2 0xfffc8000 -#define AT91RM9200_BASE_US3 0xfffcc000 -#define AT91RM9200_BASE_SSC0 0xfffd0000 -#define AT91RM9200_BASE_SSC1 0xfffd4000 -#define AT91RM9200_BASE_SSC2 0xfffd8000 -#define AT91RM9200_BASE_SPI 0xfffe0000 -#define AT91_BASE_SYS 0xfffff000 - - -/* - * System Peripherals (offset from AT91_BASE_SYS) - */ -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */ -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) /* Debug Unit */ -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) /* PIO Controller A */ -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) /* PIO Controller B */ -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) /* PIO Controller C */ -#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS) /* PIO Controller D */ -#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */ -#define AT91_ST (0xfffffd00 - AT91_BASE_SYS) /* System Timer */ -#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) /* Real-Time Clock */ -#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */ - -#define AT91_MATRIX 0 /* not supported */ - -/* - * Internal Memory. - */ -#define AT91RM9200_ROM_BASE 0x00100000 /* Internal ROM base address */ -#define AT91RM9200_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ - -#define AT91RM9200_SRAM_BASE 0x00200000 /* Internal SRAM base address */ -#define AT91RM9200_SRAM_SIZE SZ_16K /* Internal SRAM size (16Kb) */ - -#define AT91RM9200_UHP_BASE 0x00300000 /* USB Host controller */ - - -#if 0 -/* - * PIO pin definitions (peripheral A/B multiplexing). - */ -#define AT91_PA0_MISO (1 << 0) /* A: SPI Master-In Slave-Out */ -#define AT91_PA0_PCK3 (1 << 0) /* B: PMC Programmable Clock Output 3 */ -#define AT91_PA1_MOSI (1 << 1) /* A: SPI Master-Out Slave-In */ -#define AT91_PA1_PCK0 (1 << 1) /* B: PMC Programmable Clock Output 0 */ -#define AT91_PA2_SPCK (1 << 2) /* A: SPI Serial Clock */ -#define AT91_PA2_IRQ4 (1 << 2) /* B: External Interrupt 4 */ -#define AT91_PA3_NPCS0 (1 << 3) /* A: SPI Peripheral Chip Select 0 */ -#define AT91_PA3_IRQ5 (1 << 3) /* B: External Interrupt 5 */ -#define AT91_PA4_NPCS1 (1 << 4) /* A: SPI Peripheral Chip Select 1 */ -#define AT91_PA4_PCK1 (1 << 4) /* B: PMC Programmable Clock Output 1 */ -#define AT91_PA5_NPCS2 (1 << 5) /* A: SPI Peripheral Chip Select 2 */ -#define AT91_PA5_TXD3 (1 << 5) /* B: USART Transmit Data 3 */ -#define AT91_PA6_NPCS3 (1 << 6) /* A: SPI Peripheral Chip Select 3 */ -#define AT91_PA6_RXD3 (1 << 6) /* B: USART Receive Data 3 */ -#define AT91_PA7_ETXCK_EREFCK (1 << 7) /* A: Ethernet Reference Clock / Transmit Clock */ -#define AT91_PA7_PCK2 (1 << 7) /* B: PMC Programmable Clock Output 2 */ -#define AT91_PA8_ETXEN (1 << 8) /* A: Ethernet Transmit Enable */ -#define AT91_PA8_MCCDB (1 << 8) /* B: MMC Multimedia Card B Command */ -#define AT91_PA9_ETX0 (1 << 9) /* A: Ethernet Transmit Data 0 */ -#define AT91_PA9_MCDB0 (1 << 9) /* B: MMC Multimedia Card B Data 0 */ -#define AT91_PA10_ETX1 (1 << 10) /* A: Ethernet Transmit Data 1 */ -#define AT91_PA10_MCDB1 (1 << 10) /* B: MMC Multimedia Card B Data 1 */ -#define AT91_PA11_ECRS_ECRSDV (1 << 11) /* A: Ethernet Carrier Sense / Data Valid */ -#define AT91_PA11_MCDB2 (1 << 11) /* B: MMC Multimedia Card B Data 2 */ -#define AT91_PA12_ERX0 (1 << 12) /* A: Ethernet Receive Data 0 */ -#define AT91_PA12_MCDB3 (1 << 12) /* B: MMC Multimedia Card B Data 3 */ -#define AT91_PA13_ERX1 (1 << 13) /* A: Ethernet Receive Data 1 */ -#define AT91_PA13_TCLK0 (1 << 13) /* B: TC External Clock Input 0 */ -#define AT91_PA14_ERXER (1 << 14) /* A: Ethernet Receive Error */ -#define AT91_PA14_TCLK1 (1 << 14) /* B: TC External Clock Input 1 */ -#define AT91_PA15_EMDC (1 << 15) /* A: Ethernet Management Data Clock */ -#define AT91_PA15_TCLK2 (1 << 15) /* B: TC External Clock Input 2 */ -#define AT91_PA16_EMDIO (1 << 16) /* A: Ethernet Management Data I/O */ -#define AT91_PA16_IRQ6 (1 << 16) /* B: External Interrupt 6 */ -#define AT91_PA17_TXD0 (1 << 17) /* A: USART Transmit Data 0 */ -#define AT91_PA17_TIOA0 (1 << 17) /* B: TC I/O Line A 0 */ -#define AT91_PA18_RXD0 (1 << 18) /* A: USART Receive Data 0 */ -#define AT91_PA18_TIOB0 (1 << 18) /* B: TC I/O Line B 0 */ -#define AT91_PA19_SCK0 (1 << 19) /* A: USART Serial Clock 0 */ -#define AT91_PA19_TIOA1 (1 << 19) /* B: TC I/O Line A 1 */ -#define AT91_PA20_CTS0 (1 << 20) /* A: USART Clear To Send 0 */ -#define AT91_PA20_TIOB1 (1 << 20) /* B: TC I/O Line B 1 */ -#define AT91_PA21_RTS0 (1 << 21) /* A: USART Ready To Send 0 */ -#define AT91_PA21_TIOA2 (1 << 21) /* B: TC I/O Line A 2 */ -#define AT91_PA22_RXD2 (1 << 22) /* A: USART Receive Data 2 */ -#define AT91_PA22_TIOB2 (1 << 22) /* B: TC I/O Line B 2 */ -#define AT91_PA23_TXD2 (1 << 23) /* A: USART Transmit Data 2 */ -#define AT91_PA23_IRQ3 (1 << 23) /* B: External Interrupt 3 */ -#define AT91_PA24_SCK2 (1 << 24) /* A: USART Serial Clock 2 */ -#define AT91_PA24_PCK1 (1 << 24) /* B: PMC Programmable Clock Output 1 */ -#define AT91_PA25_TWD (1 << 25) /* A: TWI Two-wire Serial Data */ -#define AT91_PA25_IRQ2 (1 << 25) /* B: External Interrupt 2 */ -#define AT91_PA26_TWCK (1 << 26) /* A: TWI Two-wire Serial Clock */ -#define AT91_PA26_IRQ1 (1 << 26) /* B: External Interrupt 1 */ -#define AT91_PA27_MCCK (1 << 27) /* A: MMC Multimedia Card Clock */ -#define AT91_PA27_TCLK3 (1 << 27) /* B: TC External Clock Input 3 */ -#define AT91_PA28_MCCDA (1 << 28) /* A: MMC Multimedia Card A Command */ -#define AT91_PA28_TCLK4 (1 << 28) /* B: TC External Clock Input 4 */ -#define AT91_PA29_MCDA0 (1 << 29) /* A: MMC Multimedia Card A Data 0 */ -#define AT91_PA29_TCLK5 (1 << 29) /* B: TC External Clock Input 5 */ -#define AT91_PA30_DRXD (1 << 30) /* A: DBGU Receive Data */ -#define AT91_PA30_CTS2 (1 << 30) /* B: USART Clear To Send 2 */ -#define AT91_PA31_DTXD (1 << 31) /* A: DBGU Transmit Data */ -#define AT91_PA31_RTS2 (1 << 31) /* B: USART Ready To Send 2 */ - -#define AT91_PB0_TF0 (1 << 0) /* A: SSC Transmit Frame Sync 0 */ -#define AT91_PB0_RTS3 (1 << 0) /* B: USART Ready To Send 3 */ -#define AT91_PB1_TK0 (1 << 1) /* A: SSC Transmit Clock 0 */ -#define AT91_PB1_CTS3 (1 << 1) /* B: USART Clear To Send 3 */ -#define AT91_PB2_TD0 (1 << 2) /* A: SSC Transmit Data 0 */ -#define AT91_PB2_SCK3 (1 << 2) /* B: USART Serial Clock 3 */ -#define AT91_PB3_RD0 (1 << 3) /* A: SSC Receive Data 0 */ -#define AT91_PB3_MCDA1 (1 << 3) /* B: MMC Multimedia Card A Data 1 */ -#define AT91_PB4_RK0 (1 << 4) /* A: SSC Receive Clock 0 */ -#define AT91_PB4_MCDA2 (1 << 4) /* B: MMC Multimedia Card A Data 2 */ -#define AT91_PB5_RF0 (1 << 5) /* A: SSC Receive Frame Sync 0 */ -#define AT91_PB5_MCDA3 (1 << 5) /* B: MMC Multimedia Card A Data 3 */ -#define AT91_PB6_TF1 (1 << 6) /* A: SSC Transmit Frame Sync 1 */ -#define AT91_PB6_TIOA3 (1 << 6) /* B: TC I/O Line A 3 */ -#define AT91_PB7_TK1 (1 << 7) /* A: SSC Transmit Clock 1 */ -#define AT91_PB7_TIOB3 (1 << 7) /* B: TC I/O Line B 3 */ -#define AT91_PB8_TD1 (1 << 8) /* A: SSC Transmit Data 1 */ -#define AT91_PB8_TIOA4 (1 << 8) /* B: TC I/O Line A 4 */ -#define AT91_PB9_RD1 (1 << 9) /* A: SSC Receive Data 1 */ -#define AT91_PB9_TIOB4 (1 << 9) /* B: TC I/O Line B 4 */ -#define AT91_PB10_RK1 (1 << 10) /* A: SSC Receive Clock 1 */ -#define AT91_PB10_TIOA5 (1 << 10) /* B: TC I/O Line A 5 */ -#define AT91_PB11_RF1 (1 << 11) /* A: SSC Receive Frame Sync 1 */ -#define AT91_PB11_TIOB5 (1 << 11) /* B: TC I/O Line B 5 */ -#define AT91_PB12_TF2 (1 << 12) /* A: SSC Transmit Frame Sync 2 */ -#define AT91_PB12_ETX2 (1 << 12) /* B: Ethernet Transmit Data 2 */ -#define AT91_PB13_TK2 (1 << 13) /* A: SSC Transmit Clock 3 */ -#define AT91_PB13_ETX3 (1 << 13) /* B: Ethernet Transmit Data 3 */ -#define AT91_PB14_TD2 (1 << 14) /* A: SSC Transmit Data 2 */ -#define AT91_PB14_ETXER (1 << 14) /* B: Ethernet Transmit Coding Error */ -#define AT91_PB15_RD2 (1 << 15) /* A: SSC Receive Data 2 */ -#define AT91_PB15_ERX2 (1 << 15) /* B: Ethernet Receive Data 2 */ -#define AT91_PB16_RK2 (1 << 16) /* A: SSC Receive Clock 2 */ -#define AT91_PB16_ERX3 (1 << 16) /* B: Ethernet Receive Data 3 */ -#define AT91_PB17_RF2 (1 << 17) /* A: SSC Receive Frame Sync 2 */ -#define AT91_PB17_ERXDV (1 << 17) /* B: Ethernet Receive Data Valid */ -#define AT91_PB18_RI1 (1 << 18) /* A: USART Ring Indicator 1 */ -#define AT91_PB18_ECOL (1 << 18) /* B: Ethernet Collision Detected */ -#define AT91_PB19_DTR1 (1 << 19) /* A: USART Data Terminal Ready 1 */ -#define AT91_PB19_ERXCK (1 << 19) /* B: Ethernet Receive Clock */ -#define AT91_PB20_TXD1 (1 << 20) /* A: USART Transmit Data 1 */ -#define AT91_PB21_RXD1 (1 << 21) /* A: USART Receive Data 1 */ -#define AT91_PB22_SCK1 (1 << 22) /* A: USART Serial Clock 1 */ -#define AT91_PB23_DCD1 (1 << 23) /* A: USART Data Carrier Detect 1 */ -#define AT91_PB24_CTS1 (1 << 24) /* A: USART Clear To Send 1 */ -#define AT91_PB25_DSR1 (1 << 25) /* A: USART Data Set Ready 1 */ -#define AT91_PB25_EF100 (1 << 25) /* B: Ethernet Force 100 Mbit */ -#define AT91_PB26_RTS1 (1 << 26) /* A: USART Ready To Send 1 */ -#define AT91_PB27_PCK0 (1 << 27) /* B: PMC Programmable Clock Output 0 */ -#define AT91_PB28_FIQ (1 << 28) /* A: Fast Interrupt */ -#define AT91_PB29_IRQ0 (1 << 29) /* A: External Interrupt 0 */ - -#define AT91_PC0_BFCK (1 << 0) /* A: Burst Flash Clock */ -#define AT91_PC1_BFRDY_SMOE (1 << 1) /* A: Burst Flash Ready / SmartMedia Output Enable */ -#define AT91_PC2_BFAVD (1 << 2) /* A: Burst Flash Address Valid */ -#define AT91_PC3_BFBAA_SMWE (1 << 3) /* A: Burst Flash Address Advance / SmartMedia Write Enable */ -#define AT91_PC4_BFOE (1 << 4) /* A: Burst Flash Output Enable */ -#define AT91_PC5_BFWE (1 << 5) /* A: Burst Flash Write Enable */ -#define AT91_PC6_NWAIT (1 << 6) /* A: SMC Wait Signal */ -#define AT91_PC7_A23 (1 << 7) /* A: Address Bus 23 */ -#define AT91_PC8_A24 (1 << 8) /* A: Address Bus 24 */ -#define AT91_PC9_A25_CFRNW (1 << 9) /* A: Address Bus 25 / Compact Flash Read Not Write */ -#define AT91_PC10_NCS4_CFCS (1 << 10) /* A: SMC Chip Select 4 / Compact Flash Chip Select */ -#define AT91_PC11_NCS5_CFCE1 (1 << 11) /* A: SMC Chip Select 5 / Compact Flash Chip Enable 1 */ -#define AT91_PC12_NCS6_CFCE2 (1 << 12) /* A: SMC Chip Select 6 / Compact Flash Chip Enable 2 */ -#define AT91_PC13_NCS7 (1 << 13) /* A: Chip Select 7 */ - -#define AT91_PD0_ETX0 (1 << 0) /* A: Ethernet Transmit Data 0 */ -#define AT91_PD1_ETX1 (1 << 1) /* A: Ethernet Transmit Data 1 */ -#define AT91_PD2_ETX2 (1 << 2) /* A: Ethernet Transmit Data 2 */ -#define AT91_PD3_ETX3 (1 << 3) /* A: Ethernet Transmit Data 3 */ -#define AT91_PD4_ETXEN (1 << 4) /* A: Ethernet Transmit Enable */ -#define AT91_PD5_ETXER (1 << 5) /* A: Ethernet Transmit Coding Error */ -#define AT91_PD6_DTXD (1 << 6) /* A: DBGU Transmit Data */ -#define AT91_PD7_PCK0 (1 << 7) /* A: PMC Programmable Clock Output 0 */ -#define AT91_PD7_TSYNC (1 << 7) /* B: ETM Trace Synchronization Signal */ -#define AT91_PD8_PCK1 (1 << 8) /* A: PMC Programmable Clock Output 1 */ -#define AT91_PD8_TCLK (1 << 8) /* B: ETM Trace Clock */ -#define AT91_PD9_PCK2 (1 << 9) /* A: PMC Programmable Clock Output 2 */ -#define AT91_PD9_TPS0 (1 << 9) /* B: ETM Trace ARM Pipeline Status 0 */ -#define AT91_PD10_PCK3 (1 << 10) /* A: PMC Programmable Clock Output 3 */ -#define AT91_PD10_TPS1 (1 << 10) /* B: ETM Trace ARM Pipeline Status 1 */ -#define AT91_PD11_TPS2 (1 << 11) /* B: ETM Trace ARM Pipeline Status 2 */ -#define AT91_PD12_TPK0 (1 << 12) /* B: ETM Trace Packet Port 0 */ -#define AT91_PD13_TPK1 (1 << 13) /* B: ETM Trace Packet Port 1 */ -#define AT91_PD14_TPK2 (1 << 14) /* B: ETM Trace Packet Port 2 */ -#define AT91_PD15_TD0 (1 << 15) /* A: SSC Transmit Data 0 */ -#define AT91_PD15_TPK3 (1 << 15) /* B: ETM Trace Packet Port 3 */ -#define AT91_PD16_TD1 (1 << 16) /* A: SSC Transmit Data 1 */ -#define AT91_PD16_TPK4 (1 << 16) /* B: ETM Trace Packet Port 4 */ -#define AT91_PD17_TD2 (1 << 17) /* A: SSC Transmit Data 2 */ -#define AT91_PD17_TPK5 (1 << 17) /* B: ETM Trace Packet Port 5 */ -#define AT91_PD18_NPCS1 (1 << 18) /* A: SPI Peripheral Chip Select 1 */ -#define AT91_PD18_TPK6 (1 << 18) /* B: ETM Trace Packet Port 6 */ -#define AT91_PD19_NPCS2 (1 << 19) /* A: SPI Peripheral Chip Select 2 */ -#define AT91_PD19_TPK7 (1 << 19) /* B: ETM Trace Packet Port 7 */ -#define AT91_PD20_NPCS3 (1 << 20) /* A: SPI Peripheral Chip Select 3 */ -#define AT91_PD20_TPK8 (1 << 20) /* B: ETM Trace Packet Port 8 */ -#define AT91_PD21_RTS0 (1 << 21) /* A: USART Ready To Send 0 */ -#define AT91_PD21_TPK9 (1 << 21) /* B: ETM Trace Packet Port 9 */ -#define AT91_PD22_RTS1 (1 << 22) /* A: USART Ready To Send 1 */ -#define AT91_PD22_TPK10 (1 << 22) /* B: ETM Trace Packet Port 10 */ -#define AT91_PD23_RTS2 (1 << 23) /* A: USART Ready To Send 2 */ -#define AT91_PD23_TPK11 (1 << 23) /* B: ETM Trace Packet Port 11 */ -#define AT91_PD24_RTS3 (1 << 24) /* A: USART Ready To Send 3 */ -#define AT91_PD24_TPK12 (1 << 24) /* B: ETM Trace Packet Port 12 */ -#define AT91_PD25_DTR1 (1 << 25) /* A: USART Data Terminal Ready 1 */ -#define AT91_PD25_TPK13 (1 << 25) /* B: ETM Trace Packet Port 13 */ -#define AT91_PD26_TPK14 (1 << 26) /* B: ETM Trace Packet Port 14 */ -#define AT91_PD27_TPK15 (1 << 27) /* B: ETM Trace Packet Port 15 */ -#endif - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_emac.h b/include/asm-arm/arch-at91rm9200/at91rm9200_emac.h deleted file mode 100644 index fbc091e61e2f..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91rm9200_emac.h +++ /dev/null @@ -1,138 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91rm9200_emac.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Ethernet MAC registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91RM9200_EMAC_H -#define AT91RM9200_EMAC_H - -#define AT91_EMAC_CTL 0x00 /* Control Register */ -#define AT91_EMAC_LB (1 << 0) /* Loopback */ -#define AT91_EMAC_LBL (1 << 1) /* Loopback Local */ -#define AT91_EMAC_RE (1 << 2) /* Receive Enable */ -#define AT91_EMAC_TE (1 << 3) /* Transmit Enable */ -#define AT91_EMAC_MPE (1 << 4) /* Management Port Enable */ -#define AT91_EMAC_CSR (1 << 5) /* Clear Statistics Registers */ -#define AT91_EMAC_INCSTAT (1 << 6) /* Increment Statistics Registers */ -#define AT91_EMAC_WES (1 << 7) /* Write Enable for Statistics Registers */ -#define AT91_EMAC_BP (1 << 8) /* Back Pressure */ - -#define AT91_EMAC_CFG 0x04 /* Configuration Register */ -#define AT91_EMAC_SPD (1 << 0) /* Speed */ -#define AT91_EMAC_FD (1 << 1) /* Full Duplex */ -#define AT91_EMAC_BR (1 << 2) /* Bit Rate */ -#define AT91_EMAC_CAF (1 << 4) /* Copy All Frames */ -#define AT91_EMAC_NBC (1 << 5) /* No Broadcast */ -#define AT91_EMAC_MTI (1 << 6) /* Multicast Hash Enable */ -#define AT91_EMAC_UNI (1 << 7) /* Unicast Hash Enable */ -#define AT91_EMAC_BIG (1 << 8) /* Receive 1522 Bytes */ -#define AT91_EMAC_EAE (1 << 9) /* External Address Match Enable */ -#define AT91_EMAC_CLK (3 << 10) /* MDC Clock Divisor */ -#define AT91_EMAC_CLK_DIV8 (0 << 10) -#define AT91_EMAC_CLK_DIV16 (1 << 10) -#define AT91_EMAC_CLK_DIV32 (2 << 10) -#define AT91_EMAC_CLK_DIV64 (3 << 10) -#define AT91_EMAC_RTY (1 << 12) /* Retry Test */ -#define AT91_EMAC_RMII (1 << 13) /* Reduce MII (RMII) */ - -#define AT91_EMAC_SR 0x08 /* Status Register */ -#define AT91_EMAC_SR_LINK (1 << 0) /* Link */ -#define AT91_EMAC_SR_MDIO (1 << 1) /* MDIO pin */ -#define AT91_EMAC_SR_IDLE (1 << 2) /* PHY idle */ - -#define AT91_EMAC_TAR 0x0c /* Transmit Address Register */ - -#define AT91_EMAC_TCR 0x10 /* Transmit Control Register */ -#define AT91_EMAC_LEN (0x7ff << 0) /* Transmit Frame Length */ -#define AT91_EMAC_NCRC (1 << 15) /* No CRC */ - -#define AT91_EMAC_TSR 0x14 /* Transmit Status Register */ -#define AT91_EMAC_TSR_OVR (1 << 0) /* Transmit Buffer Overrun */ -#define AT91_EMAC_TSR_COL (1 << 1) /* Collision Occurred */ -#define AT91_EMAC_TSR_RLE (1 << 2) /* Retry Limit Exceeded */ -#define AT91_EMAC_TSR_IDLE (1 << 3) /* Transmitter Idle */ -#define AT91_EMAC_TSR_BNQ (1 << 4) /* Transmit Buffer not Queued */ -#define AT91_EMAC_TSR_COMP (1 << 5) /* Transmit Complete */ -#define AT91_EMAC_TSR_UND (1 << 6) /* Transmit Underrun */ - -#define AT91_EMAC_RBQP 0x18 /* Receive Buffer Queue Pointer */ - -#define AT91_EMAC_RSR 0x20 /* Receive Status Register */ -#define AT91_EMAC_RSR_BNA (1 << 0) /* Buffer Not Available */ -#define AT91_EMAC_RSR_REC (1 << 1) /* Frame Received */ -#define AT91_EMAC_RSR_OVR (1 << 2) /* RX Overrun */ - -#define AT91_EMAC_ISR 0x24 /* Interrupt Status Register */ -#define AT91_EMAC_DONE (1 << 0) /* Management Done */ -#define AT91_EMAC_RCOM (1 << 1) /* Receive Complete */ -#define AT91_EMAC_RBNA (1 << 2) /* Receive Buffer Not Available */ -#define AT91_EMAC_TOVR (1 << 3) /* Transmit Buffer Overrun */ -#define AT91_EMAC_TUND (1 << 4) /* Transmit Buffer Underrun */ -#define AT91_EMAC_RTRY (1 << 5) /* Retry Limit */ -#define AT91_EMAC_TBRE (1 << 6) /* Transmit Buffer Register Empty */ -#define AT91_EMAC_TCOM (1 << 7) /* Transmit Complete */ -#define AT91_EMAC_TIDLE (1 << 8) /* Transmit Idle */ -#define AT91_EMAC_LINK (1 << 9) /* Link */ -#define AT91_EMAC_ROVR (1 << 10) /* RX Overrun */ -#define AT91_EMAC_ABT (1 << 11) /* Abort */ - -#define AT91_EMAC_IER 0x28 /* Interrupt Enable Register */ -#define AT91_EMAC_IDR 0x2c /* Interrupt Disable Register */ -#define AT91_EMAC_IMR 0x30 /* Interrupt Mask Register */ - -#define AT91_EMAC_MAN 0x34 /* PHY Maintenance Register */ -#define AT91_EMAC_DATA (0xffff << 0) /* MDIO Data */ -#define AT91_EMAC_REGA (0x1f << 18) /* MDIO Register */ -#define AT91_EMAC_PHYA (0x1f << 23) /* MDIO PHY Address */ -#define AT91_EMAC_RW (3 << 28) /* Read/Write operation */ -#define AT91_EMAC_RW_W (1 << 28) -#define AT91_EMAC_RW_R (2 << 28) -#define AT91_EMAC_MAN_802_3 0x40020000 /* IEEE 802.3 value */ - -/* - * Statistics Registers. - */ -#define AT91_EMAC_FRA 0x40 /* Frames Transmitted OK */ -#define AT91_EMAC_SCOL 0x44 /* Single Collision Frame */ -#define AT91_EMAC_MCOL 0x48 /* Multiple Collision Frame */ -#define AT91_EMAC_OK 0x4c /* Frames Received OK */ -#define AT91_EMAC_SEQE 0x50 /* Frame Check Sequence Error */ -#define AT91_EMAC_ALE 0x54 /* Alignmemt Error */ -#define AT91_EMAC_DTE 0x58 /* Deffered Transmission Frame */ -#define AT91_EMAC_LCOL 0x5c /* Late Collision */ -#define AT91_EMAC_ECOL 0x60 /* Excessive Collision */ -#define AT91_EMAC_TUE 0x64 /* Transmit Underrun Error */ -#define AT91_EMAC_CSE 0x68 /* Carrier Sense Error */ -#define AT91_EMAC_DRFC 0x6c /* Discard RX Frame */ -#define AT91_EMAC_ROV 0x70 /* Receive Overrun */ -#define AT91_EMAC_CDE 0x74 /* Code Error */ -#define AT91_EMAC_ELR 0x78 /* Excessive Length Error */ -#define AT91_EMAC_RJB 0x7c /* Receive Jabber */ -#define AT91_EMAC_USF 0x80 /* Undersize Frame */ -#define AT91_EMAC_SQEE 0x84 /* SQE Test Error */ - -/* - * Address Registers. - */ -#define AT91_EMAC_HSL 0x90 /* Hash Address Low [31:0] */ -#define AT91_EMAC_HSH 0x94 /* Hash Address High [63:32] */ -#define AT91_EMAC_SA1L 0x98 /* Specific Address 1 Low, bytes 0-3 */ -#define AT91_EMAC_SA1H 0x9c /* Specific Address 1 High, bytes 4-5 */ -#define AT91_EMAC_SA2L 0xa0 /* Specific Address 2 Low, bytes 0-3 */ -#define AT91_EMAC_SA2H 0xa4 /* Specific Address 2 High, bytes 4-5 */ -#define AT91_EMAC_SA3L 0xa8 /* Specific Address 3 Low, bytes 0-3 */ -#define AT91_EMAC_SA3H 0xac /* Specific Address 3 High, bytes 4-5 */ -#define AT91_EMAC_SA4L 0xb0 /* Specific Address 4 Low, bytes 0-3 */ -#define AT91_EMAC_SA4H 0xb4 /* Specific Address 4 High, bytes 4-5 */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_mc.h b/include/asm-arm/arch-at91rm9200/at91rm9200_mc.h deleted file mode 100644 index 0c0d81480b3a..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91rm9200_mc.h +++ /dev/null @@ -1,160 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91rm9200_mc.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91RM9200_MC_H -#define AT91RM9200_MC_H - -/* Memory Controller */ -#define AT91_MC_RCR (AT91_MC + 0x00) /* MC Remap Control Register */ -#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */ - -#define AT91_MC_ASR (AT91_MC + 0x04) /* MC Abort Status Register */ -#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */ -#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */ -#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */ -#define AT91_MC_ABTSZ_BYTE (0 << 8) -#define AT91_MC_ABTSZ_HALFWORD (1 << 8) -#define AT91_MC_ABTSZ_WORD (2 << 8) -#define AT91_MC_ABTTYP (3 << 10) /* Abort Type Status */ -#define AT91_MC_ABTTYP_DATAREAD (0 << 10) -#define AT91_MC_ABTTYP_DATAWRITE (1 << 10) -#define AT91_MC_ABTTYP_FETCH (2 << 10) -#define AT91_MC_MST0 (1 << 16) /* ARM920T Abort Source */ -#define AT91_MC_MST1 (1 << 17) /* PDC Abort Source */ -#define AT91_MC_MST2 (1 << 18) /* UHP Abort Source */ -#define AT91_MC_MST3 (1 << 19) /* EMAC Abort Source */ -#define AT91_MC_SVMST0 (1 << 24) /* Saved ARM920T Abort Source */ -#define AT91_MC_SVMST1 (1 << 25) /* Saved PDC Abort Source */ -#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */ -#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */ - -#define AT91_MC_AASR (AT91_MC + 0x08) /* MC Abort Address Status Register */ - -#define AT91_MC_MPR (AT91_MC + 0x0c) /* MC Master Priority Register */ -#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */ -#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */ -#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */ -#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */ - -/* External Bus Interface (EBI) registers */ -#define AT91_EBI_CSA (AT91_MC + 0x60) /* Chip Select Assignment Register */ -#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */ -#define AT91_EBI_CS0A_SMC (0 << 0) -#define AT91_EBI_CS0A_BFC (1 << 0) -#define AT91_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_EBI_CS1A_SMC (0 << 1) -#define AT91_EBI_CS1A_SDRAMC (1 << 1) -#define AT91_EBI_CS3A (1 << 3) /* Chip Select 2 Assignment */ -#define AT91_EBI_CS3A_SMC (0 << 3) -#define AT91_EBI_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_EBI_CS4A (1 << 4) /* Chip Select 3 Assignment */ -#define AT91_EBI_CS4A_SMC (0 << 4) -#define AT91_EBI_CS4A_SMC_COMPACTFLASH (1 << 4) -#define AT91_EBI_CFGR (AT91_MC + 0x64) /* Configuration Register */ -#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */ - -/* Static Memory Controller (SMC) registers */ -#define AT91_SMC_CSR(n) (AT91_MC + 0x70 + ((n) * 4))/* SMC Chip Select Register */ -#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */ -#define AT91_SMC_NWS_(x) ((x) << 0) -#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */ -#define AT91_SMC_TDF (0xf << 8) /* Data Float Time */ -#define AT91_SMC_TDF_(x) ((x) << 8) -#define AT91_SMC_BAT (1 << 12) /* Byte Access Type */ -#define AT91_SMC_DBW (3 << 13) /* Data Bus Width */ -#define AT91_SMC_DBW_16 (1 << 13) -#define AT91_SMC_DBW_8 (2 << 13) -#define AT91_SMC_DPR (1 << 15) /* Data Read Protocol */ -#define AT91_SMC_ACSS (3 << 16) /* Address to Chip Select Setup */ -#define AT91_SMC_ACSS_STD (0 << 16) -#define AT91_SMC_ACSS_1 (1 << 16) -#define AT91_SMC_ACSS_2 (2 << 16) -#define AT91_SMC_ACSS_3 (3 << 16) -#define AT91_SMC_RWSETUP (7 << 24) /* Read & Write Signal Time Setup */ -#define AT91_SMC_RWSETUP_(x) ((x) << 24) -#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */ -#define AT91_SMC_RWHOLD_(x) ((x) << 28) - -/* SDRAM Controller registers */ -#define AT91_SDRAMC_MR (AT91_MC + 0x90) /* Mode Register */ -#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */ -#define AT91_SDRAMC_MODE_NORMAL (0 << 0) -#define AT91_SDRAMC_MODE_NOP (1 << 0) -#define AT91_SDRAMC_MODE_PRECHARGE (2 << 0) -#define AT91_SDRAMC_MODE_LMR (3 << 0) -#define AT91_SDRAMC_MODE_REFRESH (4 << 0) -#define AT91_SDRAMC_DBW (1 << 4) /* Data Bus Width */ -#define AT91_SDRAMC_DBW_32 (0 << 4) -#define AT91_SDRAMC_DBW_16 (1 << 4) - -#define AT91_SDRAMC_TR (AT91_MC + 0x94) /* Refresh Timer Register */ -#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */ - -#define AT91_SDRAMC_CR (AT91_MC + 0x98) /* Configuration Register */ -#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */ -#define AT91_SDRAMC_NC_8 (0 << 0) -#define AT91_SDRAMC_NC_9 (1 << 0) -#define AT91_SDRAMC_NC_10 (2 << 0) -#define AT91_SDRAMC_NC_11 (3 << 0) -#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */ -#define AT91_SDRAMC_NR_11 (0 << 2) -#define AT91_SDRAMC_NR_12 (1 << 2) -#define AT91_SDRAMC_NR_13 (2 << 2) -#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */ -#define AT91_SDRAMC_NB_2 (0 << 4) -#define AT91_SDRAMC_NB_4 (1 << 4) -#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */ -#define AT91_SDRAMC_CAS_2 (2 << 5) -#define AT91_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */ -#define AT91_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */ -#define AT91_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */ -#define AT91_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */ -#define AT91_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */ -#define AT91_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */ - -#define AT91_SDRAMC_SRR (AT91_MC + 0x9c) /* Self Refresh Register */ -#define AT91_SDRAMC_LPR (AT91_MC + 0xa0) /* Low Power Register */ -#define AT91_SDRAMC_IER (AT91_MC + 0xa4) /* Interrupt Enable Register */ -#define AT91_SDRAMC_IDR (AT91_MC + 0xa8) /* Interrupt Disable Register */ -#define AT91_SDRAMC_IMR (AT91_MC + 0xac) /* Interrupt Mask Register */ -#define AT91_SDRAMC_ISR (AT91_MC + 0xb0) /* Interrupt Status Register */ - -/* Burst Flash Controller register */ -#define AT91_BFC_MR (AT91_MC + 0xc0) /* Mode Register */ -#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */ -#define AT91_BFC_BFCOM_DISABLED (0 << 0) -#define AT91_BFC_BFCOM_ASYNC (1 << 0) -#define AT91_BFC_BFCOM_BURST (2 << 0) -#define AT91_BFC_BFCC (3 << 2) /* Burst Flash Controller Clock */ -#define AT91_BFC_BFCC_MCK (1 << 2) -#define AT91_BFC_BFCC_DIV2 (2 << 2) -#define AT91_BFC_BFCC_DIV4 (3 << 2) -#define AT91_BFC_AVL (0xf << 4) /* Address Valid Latency */ -#define AT91_BFC_PAGES (7 << 8) /* Page Size */ -#define AT91_BFC_PAGES_NO_PAGE (0 << 8) -#define AT91_BFC_PAGES_16 (1 << 8) -#define AT91_BFC_PAGES_32 (2 << 8) -#define AT91_BFC_PAGES_64 (3 << 8) -#define AT91_BFC_PAGES_128 (4 << 8) -#define AT91_BFC_PAGES_256 (5 << 8) -#define AT91_BFC_PAGES_512 (6 << 8) -#define AT91_BFC_PAGES_1024 (7 << 8) -#define AT91_BFC_OEL (3 << 12) /* Output Enable Latency */ -#define AT91_BFC_BAAEN (1 << 16) /* Burst Address Advance Enable */ -#define AT91_BFC_BFOEH (1 << 17) /* Burst Flash Output Enable Handling */ -#define AT91_BFC_MUXEN (1 << 18) /* Multiplexed Bus Enable */ -#define AT91_BFC_RDYEN (1 << 19) /* Ready Enable Mode */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91sam9260.h b/include/asm-arm/arch-at91rm9200/at91sam9260.h deleted file mode 100644 index 46f4dd65c035..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91sam9260.h +++ /dev/null @@ -1,125 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91sam9260.h - * - * (C) 2006 Andrew Victor - * - * Common definitions. - * Based on AT91SAM9260 datasheet revision A (Preliminary). - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9260_H -#define AT91SAM9260_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ -#define AT91_ID_SYS 1 /* System Peripherals */ -#define AT91SAM9260_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91SAM9260_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91SAM9260_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91SAM9260_ID_ADC 5 /* Analog-to-Digital Converter */ -#define AT91SAM9260_ID_US0 6 /* USART 0 */ -#define AT91SAM9260_ID_US1 7 /* USART 1 */ -#define AT91SAM9260_ID_US2 8 /* USART 2 */ -#define AT91SAM9260_ID_MCI 9 /* Multimedia Card Interface */ -#define AT91SAM9260_ID_UDP 10 /* USB Device Port */ -#define AT91SAM9260_ID_TWI 11 /* Two-Wire Interface */ -#define AT91SAM9260_ID_SPI0 12 /* Serial Peripheral Interface 0 */ -#define AT91SAM9260_ID_SPI1 13 /* Serial Peripheral Interface 1 */ -#define AT91SAM9260_ID_SSC 14 /* Serial Synchronous Controller */ -#define AT91SAM9260_ID_TC0 17 /* Timer Counter 0 */ -#define AT91SAM9260_ID_TC1 18 /* Timer Counter 1 */ -#define AT91SAM9260_ID_TC2 19 /* Timer Counter 2 */ -#define AT91SAM9260_ID_UHP 20 /* USB Host port */ -#define AT91SAM9260_ID_EMAC 21 /* Ethernet */ -#define AT91SAM9260_ID_ISI 22 /* Image Sensor Interface */ -#define AT91SAM9260_ID_US3 23 /* USART 3 */ -#define AT91SAM9260_ID_US4 24 /* USART 4 */ -#define AT91SAM9260_ID_US5 25 /* USART 5 */ -#define AT91SAM9260_ID_TC3 26 /* Timer Counter 3 */ -#define AT91SAM9260_ID_TC4 27 /* Timer Counter 4 */ -#define AT91SAM9260_ID_TC5 28 /* Timer Counter 5 */ -#define AT91SAM9260_ID_IRQ0 29 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91SAM9260_ID_IRQ1 30 /* Advanced Interrupt Controller (IRQ1) */ -#define AT91SAM9260_ID_IRQ2 31 /* Advanced Interrupt Controller (IRQ2) */ - - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9260_BASE_TCB0 0xfffa0000 -#define AT91SAM9260_BASE_TC0 0xfffa0000 -#define AT91SAM9260_BASE_TC1 0xfffa0040 -#define AT91SAM9260_BASE_TC2 0xfffa0080 -#define AT91SAM9260_BASE_UDP 0xfffa4000 -#define AT91SAM9260_BASE_MCI 0xfffa8000 -#define AT91SAM9260_BASE_TWI 0xfffac000 -#define AT91SAM9260_BASE_US0 0xfffb0000 -#define AT91SAM9260_BASE_US1 0xfffb4000 -#define AT91SAM9260_BASE_US2 0xfffb8000 -#define AT91SAM9260_BASE_SSC 0xfffbc000 -#define AT91SAM9260_BASE_ISI 0xfffc0000 -#define AT91SAM9260_BASE_EMAC 0xfffc4000 -#define AT91SAM9260_BASE_SPI0 0xfffc8000 -#define AT91SAM9260_BASE_SPI1 0xfffcc000 -#define AT91SAM9260_BASE_US3 0xfffd0000 -#define AT91SAM9260_BASE_US4 0xfffd4000 -#define AT91SAM9260_BASE_US5 0xfffd8000 -#define AT91SAM9260_BASE_TCB1 0xfffdc000 -#define AT91SAM9260_BASE_TC3 0xfffdc000 -#define AT91SAM9260_BASE_TC4 0xfffdc040 -#define AT91SAM9260_BASE_TC5 0xfffdc080 -#define AT91SAM9260_BASE_ADC 0xfffe0000 -#define AT91_BASE_SYS 0xffffe800 - -/* - * System Peripherals (offset from AT91_BASE_SYS) - */ -#define AT91_ECC (0xffffe800 - AT91_BASE_SYS) -#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS) -#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) -#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) -#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) -#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) -#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) -#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) - - -/* - * Internal Memory. - */ -#define AT91SAM9260_ROM_BASE 0x00100000 /* Internal ROM base address */ -#define AT91SAM9260_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ - -#define AT91SAM9260_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ -#define AT91SAM9260_SRAM0_SIZE SZ_4K /* Internal SRAM 0 size (4Kb) */ -#define AT91SAM9260_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ -#define AT91SAM9260_SRAM1_SIZE SZ_4K /* Internal SRAM 1 size (4Kb) */ - -#define AT91SAM9260_UHP_BASE 0x00500000 /* USB Host controller */ - -#if 0 -/* - * PIO pin definitions (peripheral A/B multiplexing). - */ - -// TODO: Add - -#endif - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91sam9260_matrix.h b/include/asm-arm/arch-at91rm9200/at91sam9260_matrix.h deleted file mode 100644 index 78f6b4917b8b..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91sam9260_matrix.h +++ /dev/null @@ -1,78 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91sam9260_matrix.h - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9260 datasheet revision B. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9260_MATRIX_H -#define AT91SAM9260_MATRIX_H - -#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */ -#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */ -#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */ -#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */ -#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */ -#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x04) /* Master Configuration Register 5 */ -#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ -#define AT91_MATRIX_ULBT_INFINITE (0 << 0) -#define AT91_MATRIX_ULBT_SINGLE (1 << 0) -#define AT91_MATRIX_ULBT_FOUR (2 << 0) -#define AT91_MATRIX_ULBT_EIGHT (3 << 0) -#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) - -#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ -#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */ -#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24) -#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24) - -#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */ -#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */ -#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */ -#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */ -#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */ -#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ -#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ -#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ -#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ -#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ -#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ - -#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ - -#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x11C) /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_CS1A_SMC (0 << 1) -#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_CS3A_SMC (0 << 3) -#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_CS4A_SMC (0 << 4) -#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) -#define AT91_MATRIX_CS5A (1 << 5 ) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_CS5A_SMC (0 << 5) -#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) -#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_VDDIOMSEL_3_3V (1 << 16) - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91sam9261.h b/include/asm-arm/arch-at91rm9200/at91sam9261.h deleted file mode 100644 index 8d39672d5b82..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91sam9261.h +++ /dev/null @@ -1,292 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91sam9261.h - * - * Copyright (C) SAN People - * - * Common definitions. - * Based on AT91SAM9261 datasheet revision E. (Preliminary) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9261_H -#define AT91SAM9261_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ -#define AT91_ID_SYS 1 /* System Peripherals */ -#define AT91SAM9261_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91SAM9261_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91SAM9261_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91SAM9261_ID_US0 6 /* USART 0 */ -#define AT91SAM9261_ID_US1 7 /* USART 1 */ -#define AT91SAM9261_ID_US2 8 /* USART 2 */ -#define AT91SAM9261_ID_MCI 9 /* Multimedia Card Interface */ -#define AT91SAM9261_ID_UDP 10 /* USB Device Port */ -#define AT91SAM9261_ID_TWI 11 /* Two-Wire Interface */ -#define AT91SAM9261_ID_SPI0 12 /* Serial Peripheral Interface 0 */ -#define AT91SAM9261_ID_SPI1 13 /* Serial Peripheral Interface 1 */ -#define AT91SAM9261_ID_SSC0 14 /* Serial Synchronous Controller 0 */ -#define AT91SAM9261_ID_SSC1 15 /* Serial Synchronous Controller 1 */ -#define AT91SAM9261_ID_SSC2 16 /* Serial Synchronous Controller 2 */ -#define AT91SAM9261_ID_TC0 17 /* Timer Counter 0 */ -#define AT91SAM9261_ID_TC1 18 /* Timer Counter 1 */ -#define AT91SAM9261_ID_TC2 19 /* Timer Counter 2 */ -#define AT91SAM9261_ID_UHP 20 /* USB Host port */ -#define AT91SAM9261_ID_LCDC 21 /* LDC Controller */ -#define AT91SAM9261_ID_IRQ0 29 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91SAM9261_ID_IRQ1 30 /* Advanced Interrupt Controller (IRQ1) */ -#define AT91SAM9261_ID_IRQ2 31 /* Advanced Interrupt Controller (IRQ2) */ - - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9261_BASE_TCB0 0xfffa0000 -#define AT91SAM9261_BASE_TC0 0xfffa0000 -#define AT91SAM9261_BASE_TC1 0xfffa0040 -#define AT91SAM9261_BASE_TC2 0xfffa0080 -#define AT91SAM9261_BASE_UDP 0xfffa4000 -#define AT91SAM9261_BASE_MCI 0xfffa8000 -#define AT91SAM9261_BASE_TWI 0xfffac000 -#define AT91SAM9261_BASE_US0 0xfffb0000 -#define AT91SAM9261_BASE_US1 0xfffb4000 -#define AT91SAM9261_BASE_US2 0xfffb8000 -#define AT91SAM9261_BASE_SSC0 0xfffbc000 -#define AT91SAM9261_BASE_SSC1 0xfffc0000 -#define AT91SAM9261_BASE_SSC2 0xfffc4000 -#define AT91SAM9261_BASE_SPI0 0xfffc8000 -#define AT91SAM9261_BASE_SPI1 0xfffcc000 -#define AT91_BASE_SYS 0xffffea00 - - -/* - * System Peripherals (offset from AT91_BASE_SYS) - */ -#define AT91_SDRAMC (0xffffea00 - AT91_BASE_SYS) -#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) -#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) -#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) -#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) -#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) - - -/* - * Internal Memory. - */ -#define AT91SAM9261_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define AT91SAM9261_SRAM_SIZE 0x00028000 /* Internal SRAM size (160Kb) */ - -#define AT91SAM9261_ROM_BASE 0x00400000 /* Internal ROM base address */ -#define AT91SAM9261_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ - -#define AT91SAM9261_UHP_BASE 0x00500000 /* USB Host controller */ -#define AT91SAM9261_LCDC_BASE 0x00600000 /* LDC controller */ - - -#if 0 -/* - * PIO pin definitions (peripheral A/B multiplexing). - */ -#define AT91_PA0_SPI0_MISO (1 << 0) /* A: SPI0 Master In Slave */ -#define AT91_PA0_MCDA0 (1 << 0) /* B: Multimedia Card A Data 0 */ -#define AT91_PA1_SPI0_MOSI (1 << 1) /* A: SPI0 Master Out Slave */ -#define AT91_PA1_MCCDA (1 << 1) /* B: Multimedia Card A Command */ -#define AT91_PA2_SPI0_SPCK (1 << 2) /* A: SPI0 Serial Clock */ -#define AT91_PA2_MCCK (1 << 2) /* B: Multimedia Card Clock */ -#define AT91_PA3_SPI0_NPCS0 (1 << 3) /* A: SPI0 Peripheral Chip Select 0 */ -#define AT91_PA4_SPI0_NPCS1 (1 << 4) /* A: SPI0 Peripheral Chip Select 1 */ -#define AT91_PA4_MCDA1 (1 << 4) /* B: Multimedia Card A Data 1 */ -#define AT91_PA5_SPI0_NPCS2 (1 << 5) /* A: SPI0 Peripheral Chip Select 2 */ -#define AT91_PA5_MCDA2 (1 << 5) /* B: Multimedia Card A Data 2 */ -#define AT91_PA6_SPI0_NPCS3 (1 << 6) /* A: SPI0 Peripheral Chip Select 3 */ -#define AT91_PA6_MCDA3 (1 << 6) /* B: Multimedia Card A Data 3 */ -#define AT91_PA7_TWD (1 << 7) /* A: TWI Two-wire Serial Data */ -#define AT91_PA7_PCK0 (1 << 7) /* B: PMC Programmable clock Output 0 */ -#define AT91_PA8_TWCK (1 << 8) /* A: TWI Two-wire Serial Clock */ -#define AT91_PA8_PCK1 (1 << 8) /* B: PMC Programmable clock Output 1 */ -#define AT91_PA9_DRXD (1 << 9) /* A: DBGU Debug Receive Data */ -#define AT91_PA9_PCK2 (1 << 9) /* B: PMC Programmable clock Output 2 */ -#define AT91_PA10_DTXD (1 << 10) /* A: DBGU Debug Transmit Data */ -#define AT91_PA10_PCK3 (1 << 10) /* B: PMC Programmable clock Output 3 */ -#define AT91_PA11_TSYNC (1 << 11) /* A: Trace Synchronization Signal */ -#define AT91_PA11_SCK1 (1 << 11) /* B: USART1 Serial Clock */ -#define AT91_PA12_TCLK (1 << 12) /* A: Trace Clock */ -#define AT91_PA12_RTS1 (1 << 12) /* B: USART1 Ready To Send */ -#define AT91_PA13_TPS0 (1 << 13) /* A: Trace ARM Pipeline Status 0 */ -#define AT91_PA13_CTS1 (1 << 13) /* B: USART1 Clear To Send */ -#define AT91_PA14_TPS1 (1 << 14) /* A: Trace ARM Pipeline Status 1 */ -#define AT91_PA14_SCK2 (1 << 14) /* B: USART2 Serial Clock */ -#define AT91_PA15_TPS2 (1 << 15) /* A: Trace ARM Pipeline Status 2 */ -#define AT91_PA15_RTS2 (1 << 15) /* B: USART2 Ready To Send */ -#define AT91_PA16_TPK0 (1 << 16) /* A: Trace Packet Port 0 */ -#define AT91_PA16_CTS2 (1 << 16) /* B: USART2 Clear To Send */ -#define AT91_PA17_TPK1 (1 << 17) /* A: Trace Packet Port 1 */ -#define AT91_PA17_TF1 (1 << 17) /* B: SSC1 Transmit Frame Sync */ -#define AT91_PA18_TPK2 (1 << 18) /* A: Trace Packet Port 2 */ -#define AT91_PA18_TK1 (1 << 18) /* B: SSC1 Transmit Clock */ -#define AT91_PA19_TPK3 (1 << 19) /* A: Trace Packet Port 3 */ -#define AT91_PA19_TD1 (1 << 19) /* B: SSC1 Transmit Data */ -#define AT91_PA20_TPK4 (1 << 20) /* A: Trace Packet Port 4 */ -#define AT91_PA20_RD1 (1 << 20) /* B: SSC1 Receive Data */ -#define AT91_PA21_TPK5 (1 << 21) /* A: Trace Packet Port 5 */ -#define AT91_PA21_RK1 (1 << 21) /* B: SSC1 Receive Clock */ -#define AT91_PA22_TPK6 (1 << 22) /* A: Trace Packet Port 6 */ -#define AT91_PA22_RF1 (1 << 22) /* B: SSC1 Receive Frame Sync */ -#define AT91_PA23_TPK7 (1 << 23) /* A: Trace Packet Port 7 */ -#define AT91_PA23_RTS0 (1 << 23) /* B: USART0 Ready To Send */ -#define AT91_PA24_TPK8 (1 << 24) /* A: Trace Packet Port 8 */ -#define AT91_PA24_SPI1_NPCS1 (1 << 24) /* B: SPI1 Peripheral Chip Select 1 */ -#define AT91_PA25_TPK9 (1 << 25) /* A: Trace Packet Port 9 */ -#define AT91_PA25_SPI1_NPCS2 (1 << 25) /* B: SPI1 Peripheral Chip Select 2 */ -#define AT91_PA26_TPK10 (1 << 26) /* A: Trace Packet Port 10 */ -#define AT91_PA26_SPI1_NPCS3 (1 << 26) /* B: SPI1 Peripheral Chip Select 3 */ -#define AT91_PA27_TPK11 (1 << 27) /* A: Trace Packet Port 11 */ -#define AT91_PA27_SPI0_NPCS1 (1 << 27) /* B: SPI0 Peripheral Chip Select 1 */ -#define AT91_PA28_TPK12 (1 << 28) /* A: Trace Packet Port 12 */ -#define AT91_PA28_SPI0_NPCS2 (1 << 28) /* B: SPI0 Peripheral Chip Select 2 */ -#define AT91_PA29_TPK13 (1 << 29) /* A: Trace Packet Port 13 */ -#define AT91_PA29_SPI0_NPCS3 (1 << 29) /* B: SPI0 Peripheral Chip Select 3 */ -#define AT91_PA30_TPK14 (1 << 30) /* A: Trace Packet Port 14 */ -#define AT91_PA30_A23 (1 << 30) /* B: Address Bus bit 23 */ -#define AT91_PA31_TPK15 (1 << 31) /* A: Trace Packet Port 15 */ -#define AT91_PA31_A24 (1 << 31) /* B: Address Bus bit 24 */ - -#define AT91_PB0_LCDVSYNC (1 << 0) /* A: LCD Vertical Synchronization */ -#define AT91_PB1_LCDHSYNC (1 << 1) /* A: LCD Horizontal Synchronization */ -#define AT91_PB2_LCDDOTCK (1 << 2) /* A: LCD Dot Clock */ -#define AT91_PB2_PCK0 (1 << 2) /* B: PMC Programmable clock Output 0 */ -#define AT91_PB3_LCDDEN (1 << 3) /* A: LCD Data Enable */ -#define AT91_PB4_LCDCC (1 << 4) /* A: LCD Contrast Control */ -#define AT91_PB4_LCDD2 (1 << 4) /* B: LCD Data Bus Bit 2 */ -#define AT91_PB5_LCDD0 (1 << 5) /* A: LCD Data Bus Bit 0 */ -#define AT91_PB5_LCDD3 (1 << 5) /* B: LCD Data Bus Bit 3 */ -#define AT91_PB6_LCDD1 (1 << 6) /* A: LCD Data Bus Bit 1 */ -#define AT91_PB6_LCDD4 (1 << 6) /* B: LCD Data Bus Bit 4 */ -#define AT91_PB7_LCDD2 (1 << 7) /* A: LCD Data Bus Bit 2 */ -#define AT91_PB7_LCDD5 (1 << 7) /* B: LCD Data Bus Bit 5 */ -#define AT91_PB8_LCDD3 (1 << 8) /* A: LCD Data Bus Bit 3 */ -#define AT91_PB8_LCDD6 (1 << 8) /* B: LCD Data Bus Bit 6 */ -#define AT91_PB9_LCDD4 (1 << 9) /* A: LCD Data Bus Bit 4 */ -#define AT91_PB9_LCDD7 (1 << 9) /* B: LCD Data Bus Bit 7 */ -#define AT91_PB10_LCDD5 (1 << 10) /* A: LCD Data Bus Bit 5 */ -#define AT91_PB10_LCDD10 (1 << 10) /* B: LCD Data Bus Bit 10 */ -#define AT91_PB11_LCDD6 (1 << 11) /* A: LCD Data Bus Bit 6 */ -#define AT91_PB11_LCDD11 (1 << 11) /* B: LCD Data Bus Bit 11 */ -#define AT91_PB12_LCDD7 (1 << 12) /* A: LCD Data Bus Bit 7 */ -#define AT91_PB12_LCDD12 (1 << 12) /* B: LCD Data Bus Bit 12 */ -#define AT91_PB13_LCDD8 (1 << 13) /* A: LCD Data Bus Bit 8 */ -#define AT91_PB13_LCDD13 (1 << 13) /* B: LCD Data Bus Bit 13 */ -#define AT91_PB14_LCDD9 (1 << 14) /* A: LCD Data Bus Bit 9 */ -#define AT91_PB14_LCDD14 (1 << 14) /* B: LCD Data Bus Bit 14 */ -#define AT91_PB15_LCDD10 (1 << 15) /* A: LCD Data Bus Bit 10 */ -#define AT91_PB15_LCDD15 (1 << 15) /* B: LCD Data Bus Bit 15 */ -#define AT91_PB16_LCDD11 (1 << 16) /* A: LCD Data Bus Bit 11 */ -#define AT91_PB16_LCDD19 (1 << 16) /* B: LCD Data Bus Bit 19 */ -#define AT91_PB17_LCDD12 (1 << 17) /* A: LCD Data Bus Bit 12 */ -#define AT91_PB17_LCDD20 (1 << 17) /* B: LCD Data Bus Bit 20 */ -#define AT91_PB18_LCDD13 (1 << 18) /* A: LCD Data Bus Bit 13 */ -#define AT91_PB18_LCDD21 (1 << 18) /* B: LCD Data Bus Bit 21 */ -#define AT91_PB19_LCDD14 (1 << 19) /* A: LCD Data Bus Bit 14 */ -#define AT91_PB19_LCDD22 (1 << 19) /* B: LCD Data Bus Bit 22 */ -#define AT91_PB20_LCDD15 (1 << 20) /* A: LCD Data Bus Bit 15 */ -#define AT91_PB20_LCDD23 (1 << 20) /* B: LCD Data Bus Bit 23 */ -#define AT91_PB21_TF0 (1 << 21) /* A: SSC0 Transmit Frame Sync */ -#define AT91_PB21_LCDD16 (1 << 21) /* B: LCD Data Bus Bit 16 */ -#define AT91_PB22_TK0 (1 << 22) /* A: SSC0 Transmit Clock */ -#define AT91_PB22_LCDD17 (1 << 22) /* B: LCD Data Bus Bit 17 */ -#define AT91_PB23_TD0 (1 << 23) /* A: SSC0 Transmit Data */ -#define AT91_PB23_LCDD18 (1 << 23) /* B: LCD Data Bus Bit 18 */ -#define AT91_PB24_RD0 (1 << 24) /* A: SSC0 Receive Data */ -#define AT91_PB24_LCDD19 (1 << 24) /* B: LCD Data Bus Bit 19 */ -#define AT91_PB25_RK0 (1 << 25) /* A: SSC0 Receive Clock */ -#define AT91_PB25_LCDD20 (1 << 25) /* B: LCD Data Bus Bit 20 */ -#define AT91_PB26_RF0 (1 << 26) /* A: SSC0 Receive Frame Sync */ -#define AT91_PB26_LCDD21 (1 << 26) /* B: LCD Data Bus Bit 21 */ -#define AT91_PB27_SPI1_NPCS1 (1 << 27) /* A: SPI1 Peripheral Chip Select 1 */ -#define AT91_PB27_LCDD22 (1 << 27) /* B: LCD Data Bus Bit 22 */ -#define AT91_PB28_SPI1_NPCS0 (1 << 28) /* A: SPI1 Peripheral Chip Select 0 */ -#define AT91_PB28_LCDD23 (1 << 28) /* B: LCD Data Bus Bit 23 */ -#define AT91_PB29_SPI1_SPCK (1 << 29) /* A: SPI1 Serial Clock */ -#define AT91_PB29_IRQ2 (1 << 29) /* B: Interrupt input 2 */ -#define AT91_PB30_SPI1_MISO (1 << 30) /* A: SPI1 Master In Slave */ -#define AT91_PB30_IRQ1 (1 << 30) /* B: Interrupt input 1 */ -#define AT91_PB31_SPI1_MOSI (1 << 31) /* A: SPI1 Master Out Slave */ -#define AT91_PB31_PCK2 (1 << 31) /* B: PMC Programmable clock Output 2 */ - -#define AT91_PC0_SMOE (1 << 0) /* A: SmartMedia Output Enable */ -#define AT91_PC0_NCS6 (1 << 0) /* B: Chip Select 6 */ -#define AT91_PC1_SMWE (1 << 1) /* A: SmartMedia Write Enable */ -#define AT91_PC1_NCS7 (1 << 1) /* B: Chip Select 7 */ -#define AT91_PC2_NWAIT (1 << 2) /* A: NWAIT */ -#define AT91_PC2_IRQ0 (1 << 2) /* B: Interrupt input 0 */ -#define AT91_PC3_A25_CFRNW (1 << 3) /* A: Address Bus[25] / Compact Flash Read Not Write */ -#define AT91_PC4_NCS4_CFCS0 (1 << 4) /* A: Chip Select 4 / CompactFlash Chip Select 0 */ -#define AT91_PC5_NCS5_CFCS1 (1 << 5) /* A: Chip Select 5 / CompactFlash Chip Select 1 */ -#define AT91_PC6_CFCE1 (1 << 6) /* A: CompactFlash Chip Enable 1 */ -#define AT91_PC7_CFCE2 (1 << 7) /* A: CompactFlash Chip Enable 2 */ -#define AT91_PC8_TXD0 (1 << 8) /* A: USART0 Transmit Data */ -#define AT91_PC8_PCK2 (1 << 8) /* B: PMC Programmable clock Output 2 */ -#define AT91_PC9_RXD0 (1 << 9) /* A: USART0 Receive Data */ -#define AT91_PC9_PCK3 (1 << 9) /* B: PMC Programmable clock Output 3 */ -#define AT91_PC10_RTS0 (1 << 10) /* A: USART0 Ready To Send */ -#define AT91_PC10_SCK0 (1 << 10) /* B: USART0 Serial Clock */ -#define AT91_PC11_CTS0 (1 << 11) /* A: USART0 Clear To Send */ -#define AT91_PC11_FIQ (1 << 11) /* B: AIC Fast Interrupt Input */ -#define AT91_PC12_TXD1 (1 << 12) /* A: USART1 Transmit Data */ -#define AT91_PC12_NCS6 (1 << 12) /* B: Chip Select 6 */ -#define AT91_PC13_RXD1 (1 << 13) /* A: USART1 Receive Data */ -#define AT91_PC13_NCS7 (1 << 13) /* B: Chip Select 7 */ -#define AT91_PC14_TXD2 (1 << 14) /* A: USART2 Transmit Data */ -#define AT91_PC14_SPI1_NPCS2 (1 << 14) /* B: SPI1 Peripheral Chip Select 2 */ -#define AT91_PC15_RXD2 (1 << 15) /* A: USART2 Receive Data */ -#define AT91_PC15_SPI1_NPCS3 (1 << 15) /* B: SPI1 Peripheral Chip Select 3 */ -#define AT91_PC16_D16 (1 << 16) /* A: Data Bus [16] */ -#define AT91_PC16_TCLK0 (1 << 16) /* B: Timer Counter 0 external clock input */ -#define AT91_PC17_D17 (1 << 17) /* A: Data Bus [17] */ -#define AT91_PC17_TCLK1 (1 << 17) /* B: Timer Counter 1 external clock input */ -#define AT91_PC18_D18 (1 << 18) /* A: Data Bus [18] */ -#define AT91_PC18_TCLK2 (1 << 18) /* B: Timer Counter 2 external clock input */ -#define AT91_PC19_D19 (1 << 19) /* A: Data Bus [19] */ -#define AT91_PC19_TIOA0 (1 << 19) /* B: Timer Counter 0 Multipurpose Timer I/O Pin A */ -#define AT91_PC20_D20 (1 << 20) /* A: Data Bus [20] */ -#define AT91_PC20_TIOB0 (1 << 20) /* B: Timer Counter 0 Multipurpose Timer I/O Pin B */ -#define AT91_PC21_D21 (1 << 21) /* A: Data Bus [21] */ -#define AT91_PC21_TIOA1 (1 << 21) /* B: Timer Counter 1 Multipurpose Timer I/O Pin A */ -#define AT91_PC22_D22 (1 << 22) /* A: Data Bus [22] */ -#define AT91_PC22_TIOB1 (1 << 22) /* B: Timer Counter 1 Multipurpose Timer I/O Pin B */ -#define AT91_PC23_D23 (1 << 23) /* A: Data Bus [23] */ -#define AT91_PC23_TIOA2 (1 << 23) /* B: Timer Counter 2 Multipurpose Timer I/O Pin A */ -#define AT91_PC24_D24 (1 << 24) /* A: Data Bus [24] */ -#define AT91_PC24_TIOB2 (1 << 24) /* B: Timer Counter 2 Multipurpose Timer I/O Pin B */ -#define AT91_PC25_D25 (1 << 25) /* A: Data Bus [25] */ -#define AT91_PC25_TF2 (1 << 25) /* B: SSC2 Transmit Frame Sync */ -#define AT91_PC26_D26 (1 << 26) /* A: Data Bus [26] */ -#define AT91_PC26_TK2 (1 << 26) /* B: SSC2 Transmit Clock */ -#define AT91_PC27_D27 (1 << 27) /* A: Data Bus [27] */ -#define AT91_PC27_TD2 (1 << 27) /* B: SSC2 Transmit Data */ -#define AT91_PC28_D28 (1 << 28) /* A: Data Bus [28] */ -#define AT91_PC28_RD2 (1 << 28) /* B: SSC2 Receive Data */ -#define AT91_PC29_D29 (1 << 29) /* A: Data Bus [29] */ -#define AT91_PC29_RK2 (1 << 29) /* B: SSC2 Receive Clock */ -#define AT91_PC30_D30 (1 << 30) /* A: Data Bus [30] */ -#define AT91_PC30_RF2 (1 << 30) /* B: SSC2 Receive Frame Sync */ -#define AT91_PC31_D31 (1 << 31) /* A: Data Bus [31] */ -#define AT91_PC31_PCK1 (1 << 31) /* B: PMC Programmable clock Output 1 */ -#endif - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91sam9261_matrix.h b/include/asm-arm/arch-at91rm9200/at91sam9261_matrix.h deleted file mode 100644 index ec88efabbe6c..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91sam9261_matrix.h +++ /dev/null @@ -1,62 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91sam9261_matrix.h - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9261_MATRIX_H -#define AT91SAM9261_MATRIX_H - -#define AT91_MATRIX_MCFG (AT91_MATRIX + 0x00) /* Master Configuration Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ - -#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x04) /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x08) /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x0C) /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x10) /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x14) /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ - -#define AT91_MATRIX_TCR (AT91_MATRIX + 0x24) /* TCM Configuration Register */ -#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ -#define AT91_MATRIX_ITCM_0 (0 << 0) -#define AT91_MATRIX_ITCM_16 (5 << 0) -#define AT91_MATRIX_ITCM_32 (6 << 0) -#define AT91_MATRIX_ITCM_64 (7 << 0) -#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ -#define AT91_MATRIX_DTCM_0 (0 << 4) -#define AT91_MATRIX_DTCM_16 (5 << 4) -#define AT91_MATRIX_DTCM_32 (6 << 4) -#define AT91_MATRIX_DTCM_64 (7 << 4) - -#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x30) /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_CS1A_SMC (0 << 1) -#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_CS3A_SMC (0 << 3) -#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_CS4A_SMC (0 << 4) -#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) -#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_CS5A_SMC (0 << 5) -#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) -#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ - -#define AT91_MATRIX_USBPUCR (AT91_MATRIX + 0x34) /* USB Pad Pull-Up Control Register */ -#define AT91_MATRIX_USBPUCR_PUON (1 << 30) /* USB Device PAD Pull-up Enable */ - -#endif diff --git a/include/asm-arm/arch-at91rm9200/at91sam926x_mc.h b/include/asm-arm/arch-at91rm9200/at91sam926x_mc.h deleted file mode 100644 index 972e7531c7f4..000000000000 --- a/include/asm-arm/arch-at91rm9200/at91sam926x_mc.h +++ /dev/null @@ -1,134 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/at91sam926x_mc.h - * - * Memory Controllers (SMC, SDRAMC) - System peripherals registers. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM926x_MC_H -#define AT91SAM926x_MC_H - -/* SDRAM Controller (SDRAMC) registers */ -#define AT91_SDRAMC_MR (AT91_SDRAMC + 0x00) /* SDRAM Controller Mode Register */ -#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */ -#define AT91_SDRAMC_MODE_NORMAL 0 -#define AT91_SDRAMC_MODE_NOP 1 -#define AT91_SDRAMC_MODE_PRECHARGE 2 -#define AT91_SDRAMC_MODE_LMR 3 -#define AT91_SDRAMC_MODE_REFRESH 4 -#define AT91_SDRAMC_MODE_EXT_LMR 5 -#define AT91_SDRAMC_MODE_DEEP 6 - -#define AT91_SDRAMC_TR (AT91_SDRAMC + 0x04) /* SDRAM Controller Refresh Timer Register */ -#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */ - -#define AT91_SDRAMC_CR (AT91_SDRAMC + 0x08) /* SDRAM Controller Configuration Register */ -#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */ -#define AT91_SDRAMC_NC_8 (0 << 0) -#define AT91_SDRAMC_NC_9 (1 << 0) -#define AT91_SDRAMC_NC_10 (2 << 0) -#define AT91_SDRAMC_NC_11 (3 << 0) -#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */ -#define AT91_SDRAMC_NR_11 (0 << 2) -#define AT91_SDRAMC_NR_12 (1 << 2) -#define AT91_SDRAMC_NR_13 (2 << 2) -#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */ -#define AT91_SDRAMC_NB_2 (0 << 4) -#define AT91_SDRAMC_NB_4 (1 << 4) -#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */ -#define AT91_SDRAMC_CAS_1 (1 << 5) -#define AT91_SDRAMC_CAS_2 (2 << 5) -#define AT91_SDRAMC_CAS_3 (3 << 5) -#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */ -#define AT91_SDRAMC_DBW_32 (0 << 7) -#define AT91_SDRAMC_DBW_16 (1 << 7) -#define AT91_SDRAMC_TWR (0xf << 8) /* Write Recovery Delay */ -#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle Delay */ -#define AT91_SDRAMC_TRP (0xf << 16) /* Row Precharge Delay */ -#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column Delay */ -#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */ -#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */ - -#define AT91_SDRAMC_LPR (AT91_SDRAMC + 0x10) /* SDRAM Controller Low Power Register */ -#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */ -#define AT91_SDRAMC_LPCB_DISABLE 0 -#define AT91_SDRAMC_LPCB_SELF_REFRESH 1 -#define AT91_SDRAMC_LPCB_POWER_DOWN 2 -#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3 -#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array Self Refresh */ -#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */ -#define AT91_SDRAMC_DS (3 << 10) /* Drive Strenght */ -#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */ -#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12) -#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12) -#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12) - -#define AT91_SDRAMC_IER (AT91_SDRAMC + 0x14) /* SDRAM Controller Interrupt Enable Register */ -#define AT91_SDRAMC_IDR (AT91_SDRAMC + 0x18) /* SDRAM Controller Interrupt Disable Register */ -#define AT91_SDRAMC_IMR (AT91_SDRAMC + 0x1C) /* SDRAM Controller Interrupt Mask Register */ -#define AT91_SDRAMC_ISR (AT91_SDRAMC + 0x20) /* SDRAM Controller Interrupt Status Register */ -#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */ - -#define AT91_SDRAMC_MDR (AT91_SDRAMC + 0x24) /* SDRAM Memory Device Register */ -#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */ -#define AT91_SDRAMC_MD_SDRAM 0 -#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1 - - -/* Static Memory Controller (SMC) registers */ -#define AT91_SMC_SETUP(n) (AT91_SMC + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ -#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */ -#define AT91_SMC_NWESETUP_(x) ((x) << 0) -#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */ -#define AT91_SMC_NCS_WRSETUP_(x) ((x) << 8) -#define AT91_SMC_NRDSETUP (0x3f << 16) /* NRD Setup Length */ -#define AT91_SMC_NRDSETUP_(x) ((x) << 16) -#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */ -#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24) - -#define AT91_SMC_PULSE(n) (AT91_SMC + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ -#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */ -#define AT91_SMC_NWEPULSE_(x) ((x) << 0) -#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */ -#define AT91_SMC_NCS_WRPULSE_(x)((x) << 8) -#define AT91_SMC_NRDPULSE (0x7f << 16) /* NRD Pulse Length */ -#define AT91_SMC_NRDPULSE_(x) ((x) << 16) -#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */ -#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24) - -#define AT91_SMC_CYCLE(n) (AT91_SMC + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ -#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */ -#define AT91_SMC_NWECYCLE_(x) ((x) << 0) -#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */ -#define AT91_SMC_NRDCYCLE_(x) ((x) << 16) - -#define AT91_SMC_MODE(n) (AT91_SMC + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ -#define AT91_SMC_READMODE (1 << 0) /* Read Mode */ -#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */ -#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */ -#define AT91_SMC_EXNWMODE_DISABLE (0 << 4) -#define AT91_SMC_EXNWMODE_FROZEN (2 << 4) -#define AT91_SMC_EXNWMODE_READY (3 << 4) -#define AT91_SMC_BAT (1 << 8) /* Byte Access Type */ -#define AT91_SMC_BAT_SELECT (0 << 8) -#define AT91_SMC_BAT_WRITE (1 << 8) -#define AT91_SMC_DBW (3 << 12) /* Data Bus Width */ -#define AT91_SMC_DBW_8 (0 << 12) -#define AT91_SMC_DBW_16 (1 << 12) -#define AT91_SMC_DBW_32 (2 << 12) -#define AT91_SMC_TDF (0xf << 16) /* Data Float Time. */ -#define AT91_SMC_TDF_(x) ((x) << 16) -#define AT91_SMC_TDFMODE (1 << 20) /* TDF Optimization - Enabled */ -#define AT91_SMC_PMEN (1 << 24) /* Page Mode Enabled */ -#define AT91_SMC_PS (3 << 28) /* Page Size */ -#define AT91_SMC_PS_4 (0 << 28) -#define AT91_SMC_PS_8 (1 << 28) -#define AT91_SMC_PS_16 (2 << 28) -#define AT91_SMC_PS_32 (3 << 28) - -#endif diff --git a/include/asm-arm/arch-at91rm9200/board.h b/include/asm-arm/arch-at91rm9200/board.h deleted file mode 100644 index f3a974ba3b51..000000000000 --- a/include/asm-arm/arch-at91rm9200/board.h +++ /dev/null @@ -1,121 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/board.h - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -/* - * These are data structures found in platform_device.dev.platform_data, - * and describing board-specific data needed by drivers. For example, - * which pin is used for a given GPIO role. - * - * In 2.6, drivers should strongly avoid board-specific knowledge so - * that supporting new boards normally won't require driver patches. - * Most board-specific knowledge should be in arch/.../board-*.c files. - */ - -#ifndef __ASM_ARCH_BOARD_H -#define __ASM_ARCH_BOARD_H - -#include -#include -#include - - /* USB Device */ -struct at91_udc_data { - u8 vbus_pin; /* high == host powering us */ - u8 pullup_pin; /* high == D+ pulled up */ -}; -extern void __init at91_add_device_udc(struct at91_udc_data *data); - - /* Compact Flash */ -struct at91_cf_data { - u8 irq_pin; /* I/O IRQ */ - u8 det_pin; /* Card detect */ - u8 vcc_pin; /* power switching */ - u8 rst_pin; /* card reset */ - u8 chipselect; /* EBI Chip Select number */ -}; -extern void __init at91_add_device_cf(struct at91_cf_data *data); - - /* MMC / SD */ -struct at91_mmc_data { - u8 det_pin; /* card detect IRQ */ - unsigned slot_b:1; /* uses Slot B */ - unsigned wire4:1; /* (SD) supports DAT0..DAT3 */ - u8 wp_pin; /* (SD) writeprotect detect */ - u8 vcc_pin; /* power switching (high == on) */ -}; -extern void __init at91_add_device_mmc(struct at91_mmc_data *data); - - /* Ethernet */ -struct at91_eth_data { - u8 phy_irq_pin; /* PHY IRQ */ - u8 is_rmii; /* using RMII interface? */ -}; -extern void __init at91_add_device_eth(struct at91_eth_data *data); - -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) -#define eth_platform_data at91_eth_data -#endif - - /* USB Host */ -struct at91_usbh_data { - u8 ports; /* number of ports on root hub */ -}; -extern void __init at91_add_device_usbh(struct at91_usbh_data *data); - - /* NAND / SmartMedia */ -struct at91_nand_data { - u8 enable_pin; /* chip enable */ - u8 det_pin; /* card detect */ - u8 rdy_pin; /* ready/busy */ - u8 ale; /* address line number connected to ALE */ - u8 cle; /* address line number connected to CLE */ - u8 bus_width_16; /* buswidth is 16 bit */ - struct mtd_partition* (*partition_info)(int, int*); -}; -extern void __init at91_add_device_nand(struct at91_nand_data *data); - - /* I2C*/ -extern void __init at91_add_device_i2c(void); - - /* SPI */ -extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices); - - /* Serial */ -struct at91_uart_config { - unsigned short console_tty; /* tty number of serial console */ - unsigned short nr_tty; /* number of serial tty's */ - short tty_map[]; /* map UART to tty number */ -}; -extern struct platform_device *atmel_default_console_device; -extern void __init at91_init_serial(struct at91_uart_config *config); - -struct atmel_uart_data { - short use_dma_tx; /* use transmit DMA? */ - short use_dma_rx; /* use receive DMA? */ - void __iomem *regs; /* virtual base address, if any */ -}; -extern void __init at91_add_device_serial(void); - - /* LEDs */ -extern u8 at91_leds_cpu; -extern u8 at91_leds_timer; -extern void __init at91_init_leds(u8 cpu_led, u8 timer_led); - -#endif diff --git a/include/asm-arm/arch-at91rm9200/cpu.h b/include/asm-arm/arch-at91rm9200/cpu.h deleted file mode 100644 index 6f8d09b08692..000000000000 --- a/include/asm-arm/arch-at91rm9200/cpu.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/cpu.h - * - * Copyright (C) 2006 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#ifndef __ASM_ARCH_CPU_H -#define __ASM_ARCH_CPU_H - -#include -#include - - -#define ARCH_ID_AT91RM9200 0x09290780 -#define ARCH_ID_AT91SAM9260 0x019803a0 -#define ARCH_ID_AT91SAM9261 0x019703a0 - - -static inline unsigned long at91_cpu_identify(void) -{ - return (at91_sys_read(AT91_DBGU_CIDR) & ~AT91_CIDR_VERSION); -} - - -#ifdef CONFIG_ARCH_AT91RM9200 -#define cpu_is_at91rm9200() (at91_cpu_identify() == ARCH_ID_AT91RM9200) -#else -#define cpu_is_at91rm9200() (0) -#endif - -#ifdef CONFIG_ARCH_AT91SAM9260 -#define cpu_is_at91sam9260() (at91_cpu_identify() == ARCH_ID_AT91SAM9260) -#else -#define cpu_is_at91sam9260() (0) -#endif - -#ifdef CONFIG_ARCH_AT91SAM9261 -#define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261) -#else -#define cpu_is_at91sam9261() (0) -#endif - -#endif diff --git a/include/asm-arm/arch-at91rm9200/debug-macro.S b/include/asm-arm/arch-at91rm9200/debug-macro.S deleted file mode 100644 index 85cdadf26634..000000000000 --- a/include/asm-arm/arch-at91rm9200/debug-macro.S +++ /dev/null @@ -1,39 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/debug-macro.S - * - * Copyright (C) 2003-2005 SAN People - * - * Debugging macro include header - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * -*/ - -#include -#include - - .macro addruart,rx - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =AT91_BASE_SYS @ System peripherals (phys address) - ldrne \rx, =AT91_VA_BASE_SYS @ System peripherals (virt address) - .endm - - .macro senduart,rd,rx - strb \rd, [\rx, #AT91_DBGU_THR] @ Write to Transmitter Holding Register - .endm - - .macro waituart,rd,rx -1001: ldr \rd, [\rx, #AT91_DBGU_SR] @ Read Status Register - tst \rd, #AT91_DBGU_TXRDY @ DBGU_TXRDY = 1 when ready to transmit - beq 1001b - .endm - - .macro busyuart,rd,rx -1001: ldr \rd, [\rx, #AT91_DBGU_SR] @ Read Status Register - tst \rd, #AT91_DBGU_TXEMPTY @ DBGU_TXEMPTY = 1 when transmission complete - beq 1001b - .endm - diff --git a/include/asm-arm/arch-at91rm9200/dma.h b/include/asm-arm/arch-at91rm9200/dma.h deleted file mode 100644 index 22c1dfdd8da3..000000000000 --- a/include/asm-arm/arch-at91rm9200/dma.h +++ /dev/null @@ -1,19 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/dma.h - * - * Copyright (C) 2003 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ diff --git a/include/asm-arm/arch-at91rm9200/entry-macro.S b/include/asm-arm/arch-at91rm9200/entry-macro.S deleted file mode 100644 index 57248a796472..000000000000 --- a/include/asm-arm/arch-at91rm9200/entry-macro.S +++ /dev/null @@ -1,26 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/entry-macro.S - * - * Copyright (C) 2003-2005 SAN People - * - * Low-level IRQ helper macros for AT91RM9200 platforms - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -#include -#include - - .macro disable_fiq - .endm - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \base, =(AT91_VA_BASE_SYS) @ base virtual address of SYS peripherals - ldr \irqnr, [\base, #AT91_AIC_IVR] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt) - ldr \irqstat, [\base, #AT91_AIC_ISR] @ read interrupt source number - teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt - streq \tmp, [\base, #AT91_AIC_EOICR] @ not going to be handled further, then ACK it now. - .endm - diff --git a/include/asm-arm/arch-at91rm9200/gpio.h b/include/asm-arm/arch-at91rm9200/gpio.h deleted file mode 100644 index a011d27876a2..000000000000 --- a/include/asm-arm/arch-at91rm9200/gpio.h +++ /dev/null @@ -1,199 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/gpio.h - * - * Copyright (C) 2005 HP Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#ifndef __ASM_ARCH_AT91RM9200_GPIO_H -#define __ASM_ARCH_AT91RM9200_GPIO_H - -#include - -#define PIN_BASE NR_AIC_IRQS - -#define MAX_GPIO_BANKS 4 - -/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */ - -#define AT91_PIN_PA0 (PIN_BASE + 0x00 + 0) -#define AT91_PIN_PA1 (PIN_BASE + 0x00 + 1) -#define AT91_PIN_PA2 (PIN_BASE + 0x00 + 2) -#define AT91_PIN_PA3 (PIN_BASE + 0x00 + 3) -#define AT91_PIN_PA4 (PIN_BASE + 0x00 + 4) - -#define AT91_PIN_PA5 (PIN_BASE + 0x00 + 5) -#define AT91_PIN_PA6 (PIN_BASE + 0x00 + 6) -#define AT91_PIN_PA7 (PIN_BASE + 0x00 + 7) -#define AT91_PIN_PA8 (PIN_BASE + 0x00 + 8) -#define AT91_PIN_PA9 (PIN_BASE + 0x00 + 9) - -#define AT91_PIN_PA10 (PIN_BASE + 0x00 + 10) -#define AT91_PIN_PA11 (PIN_BASE + 0x00 + 11) -#define AT91_PIN_PA12 (PIN_BASE + 0x00 + 12) -#define AT91_PIN_PA13 (PIN_BASE + 0x00 + 13) -#define AT91_PIN_PA14 (PIN_BASE + 0x00 + 14) - -#define AT91_PIN_PA15 (PIN_BASE + 0x00 + 15) -#define AT91_PIN_PA16 (PIN_BASE + 0x00 + 16) -#define AT91_PIN_PA17 (PIN_BASE + 0x00 + 17) -#define AT91_PIN_PA18 (PIN_BASE + 0x00 + 18) -#define AT91_PIN_PA19 (PIN_BASE + 0x00 + 19) - -#define AT91_PIN_PA20 (PIN_BASE + 0x00 + 20) -#define AT91_PIN_PA21 (PIN_BASE + 0x00 + 21) -#define AT91_PIN_PA22 (PIN_BASE + 0x00 + 22) -#define AT91_PIN_PA23 (PIN_BASE + 0x00 + 23) -#define AT91_PIN_PA24 (PIN_BASE + 0x00 + 24) - -#define AT91_PIN_PA25 (PIN_BASE + 0x00 + 25) -#define AT91_PIN_PA26 (PIN_BASE + 0x00 + 26) -#define AT91_PIN_PA27 (PIN_BASE + 0x00 + 27) -#define AT91_PIN_PA28 (PIN_BASE + 0x00 + 28) -#define AT91_PIN_PA29 (PIN_BASE + 0x00 + 29) - -#define AT91_PIN_PA30 (PIN_BASE + 0x00 + 30) -#define AT91_PIN_PA31 (PIN_BASE + 0x00 + 31) - -#define AT91_PIN_PB0 (PIN_BASE + 0x20 + 0) -#define AT91_PIN_PB1 (PIN_BASE + 0x20 + 1) -#define AT91_PIN_PB2 (PIN_BASE + 0x20 + 2) -#define AT91_PIN_PB3 (PIN_BASE + 0x20 + 3) -#define AT91_PIN_PB4 (PIN_BASE + 0x20 + 4) - -#define AT91_PIN_PB5 (PIN_BASE + 0x20 + 5) -#define AT91_PIN_PB6 (PIN_BASE + 0x20 + 6) -#define AT91_PIN_PB7 (PIN_BASE + 0x20 + 7) -#define AT91_PIN_PB8 (PIN_BASE + 0x20 + 8) -#define AT91_PIN_PB9 (PIN_BASE + 0x20 + 9) - -#define AT91_PIN_PB10 (PIN_BASE + 0x20 + 10) -#define AT91_PIN_PB11 (PIN_BASE + 0x20 + 11) -#define AT91_PIN_PB12 (PIN_BASE + 0x20 + 12) -#define AT91_PIN_PB13 (PIN_BASE + 0x20 + 13) -#define AT91_PIN_PB14 (PIN_BASE + 0x20 + 14) - -#define AT91_PIN_PB15 (PIN_BASE + 0x20 + 15) -#define AT91_PIN_PB16 (PIN_BASE + 0x20 + 16) -#define AT91_PIN_PB17 (PIN_BASE + 0x20 + 17) -#define AT91_PIN_PB18 (PIN_BASE + 0x20 + 18) -#define AT91_PIN_PB19 (PIN_BASE + 0x20 + 19) - -#define AT91_PIN_PB20 (PIN_BASE + 0x20 + 20) -#define AT91_PIN_PB21 (PIN_BASE + 0x20 + 21) -#define AT91_PIN_PB22 (PIN_BASE + 0x20 + 22) -#define AT91_PIN_PB23 (PIN_BASE + 0x20 + 23) -#define AT91_PIN_PB24 (PIN_BASE + 0x20 + 24) - -#define AT91_PIN_PB25 (PIN_BASE + 0x20 + 25) -#define AT91_PIN_PB26 (PIN_BASE + 0x20 + 26) -#define AT91_PIN_PB27 (PIN_BASE + 0x20 + 27) -#define AT91_PIN_PB28 (PIN_BASE + 0x20 + 28) -#define AT91_PIN_PB29 (PIN_BASE + 0x20 + 29) - -#define AT91_PIN_PB30 (PIN_BASE + 0x20 + 30) -#define AT91_PIN_PB31 (PIN_BASE + 0x20 + 31) - -#define AT91_PIN_PC0 (PIN_BASE + 0x40 + 0) -#define AT91_PIN_PC1 (PIN_BASE + 0x40 + 1) -#define AT91_PIN_PC2 (PIN_BASE + 0x40 + 2) -#define AT91_PIN_PC3 (PIN_BASE + 0x40 + 3) -#define AT91_PIN_PC4 (PIN_BASE + 0x40 + 4) - -#define AT91_PIN_PC5 (PIN_BASE + 0x40 + 5) -#define AT91_PIN_PC6 (PIN_BASE + 0x40 + 6) -#define AT91_PIN_PC7 (PIN_BASE + 0x40 + 7) -#define AT91_PIN_PC8 (PIN_BASE + 0x40 + 8) -#define AT91_PIN_PC9 (PIN_BASE + 0x40 + 9) - -#define AT91_PIN_PC10 (PIN_BASE + 0x40 + 10) -#define AT91_PIN_PC11 (PIN_BASE + 0x40 + 11) -#define AT91_PIN_PC12 (PIN_BASE + 0x40 + 12) -#define AT91_PIN_PC13 (PIN_BASE + 0x40 + 13) -#define AT91_PIN_PC14 (PIN_BASE + 0x40 + 14) - -#define AT91_PIN_PC15 (PIN_BASE + 0x40 + 15) -#define AT91_PIN_PC16 (PIN_BASE + 0x40 + 16) -#define AT91_PIN_PC17 (PIN_BASE + 0x40 + 17) -#define AT91_PIN_PC18 (PIN_BASE + 0x40 + 18) -#define AT91_PIN_PC19 (PIN_BASE + 0x40 + 19) - -#define AT91_PIN_PC20 (PIN_BASE + 0x40 + 20) -#define AT91_PIN_PC21 (PIN_BASE + 0x40 + 21) -#define AT91_PIN_PC22 (PIN_BASE + 0x40 + 22) -#define AT91_PIN_PC23 (PIN_BASE + 0x40 + 23) -#define AT91_PIN_PC24 (PIN_BASE + 0x40 + 24) - -#define AT91_PIN_PC25 (PIN_BASE + 0x40 + 25) -#define AT91_PIN_PC26 (PIN_BASE + 0x40 + 26) -#define AT91_PIN_PC27 (PIN_BASE + 0x40 + 27) -#define AT91_PIN_PC28 (PIN_BASE + 0x40 + 28) -#define AT91_PIN_PC29 (PIN_BASE + 0x40 + 29) - -#define AT91_PIN_PC30 (PIN_BASE + 0x40 + 30) -#define AT91_PIN_PC31 (PIN_BASE + 0x40 + 31) - -#define AT91_PIN_PD0 (PIN_BASE + 0x60 + 0) -#define AT91_PIN_PD1 (PIN_BASE + 0x60 + 1) -#define AT91_PIN_PD2 (PIN_BASE + 0x60 + 2) -#define AT91_PIN_PD3 (PIN_BASE + 0x60 + 3) -#define AT91_PIN_PD4 (PIN_BASE + 0x60 + 4) - -#define AT91_PIN_PD5 (PIN_BASE + 0x60 + 5) -#define AT91_PIN_PD6 (PIN_BASE + 0x60 + 6) -#define AT91_PIN_PD7 (PIN_BASE + 0x60 + 7) -#define AT91_PIN_PD8 (PIN_BASE + 0x60 + 8) -#define AT91_PIN_PD9 (PIN_BASE + 0x60 + 9) - -#define AT91_PIN_PD10 (PIN_BASE + 0x60 + 10) -#define AT91_PIN_PD11 (PIN_BASE + 0x60 + 11) -#define AT91_PIN_PD12 (PIN_BASE + 0x60 + 12) -#define AT91_PIN_PD13 (PIN_BASE + 0x60 + 13) -#define AT91_PIN_PD14 (PIN_BASE + 0x60 + 14) - -#define AT91_PIN_PD15 (PIN_BASE + 0x60 + 15) -#define AT91_PIN_PD16 (PIN_BASE + 0x60 + 16) -#define AT91_PIN_PD17 (PIN_BASE + 0x60 + 17) -#define AT91_PIN_PD18 (PIN_BASE + 0x60 + 18) -#define AT91_PIN_PD19 (PIN_BASE + 0x60 + 19) - -#define AT91_PIN_PD20 (PIN_BASE + 0x60 + 20) -#define AT91_PIN_PD21 (PIN_BASE + 0x60 + 21) -#define AT91_PIN_PD22 (PIN_BASE + 0x60 + 22) -#define AT91_PIN_PD23 (PIN_BASE + 0x60 + 23) -#define AT91_PIN_PD24 (PIN_BASE + 0x60 + 24) - -#define AT91_PIN_PD25 (PIN_BASE + 0x60 + 25) -#define AT91_PIN_PD26 (PIN_BASE + 0x60 + 26) -#define AT91_PIN_PD27 (PIN_BASE + 0x60 + 27) -#define AT91_PIN_PD28 (PIN_BASE + 0x60 + 28) -#define AT91_PIN_PD29 (PIN_BASE + 0x60 + 29) - -#define AT91_PIN_PD30 (PIN_BASE + 0x60 + 30) -#define AT91_PIN_PD31 (PIN_BASE + 0x60 + 31) - -#ifndef __ASSEMBLY__ -/* setup setup routines, called from board init or driver probe() */ -extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup); -extern int __init_or_module at91_set_gpio_output(unsigned pin, int value); -extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on); -extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on); - -/* callable at any time */ -extern int at91_set_gpio_value(unsigned pin, int value); -extern int at91_get_gpio_value(unsigned pin); - -/* callable only from core power-management code */ -extern void at91_gpio_suspend(void); -extern void at91_gpio_resume(void); -#endif - -#endif - diff --git a/include/asm-arm/arch-at91rm9200/hardware.h b/include/asm-arm/arch-at91rm9200/hardware.h deleted file mode 100644 index 9ea5bfe06320..000000000000 --- a/include/asm-arm/arch-at91rm9200/hardware.h +++ /dev/null @@ -1,88 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/hardware.h - * - * Copyright (C) 2003 SAN People - * Copyright (C) 2003 ATMEL - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#ifndef __ASM_ARCH_HARDWARE_H -#define __ASM_ARCH_HARDWARE_H - -#include - -#if defined(CONFIG_ARCH_AT91RM9200) -#include -#elif defined(CONFIG_ARCH_AT91SAM9260) -#include -#elif defined(CONFIG_ARCH_AT91SAM9261) -#include -#else -#error "Unsupported AT91 processor" -#endif - - -/* - * Remap the peripherals from address 0xFFFA0000 .. 0xFFFFFFFF - * to 0xFEFA0000 .. 0xFF000000. (384Kb) - */ -#define AT91_IO_PHYS_BASE 0xFFFA0000 -#define AT91_IO_SIZE (0xFFFFFFFF - AT91_IO_PHYS_BASE + 1) -#define AT91_IO_VIRT_BASE (0xFF000000 - AT91_IO_SIZE) - - /* Convert a physical IO address to virtual IO address */ -#define AT91_IO_P2V(x) ((x) - AT91_IO_PHYS_BASE + AT91_IO_VIRT_BASE) - -/* - * Virtual to Physical Address mapping for IO devices. - */ -#define AT91_VA_BASE_SYS AT91_IO_P2V(AT91_BASE_SYS) -#define AT91_VA_BASE_EMAC AT91_IO_P2V(AT91RM9200_BASE_EMAC) - - /* Internal SRAM is mapped below the IO devices */ -#define AT91_SRAM_MAX SZ_1M -#define AT91_VIRT_BASE (AT91_IO_VIRT_BASE - AT91_SRAM_MAX) - -/* Serial ports */ -#define ATMEL_MAX_UART 7 /* 6 USART3's and one DBGU port (SAM9260) */ - -/* External Memory Map */ -#define AT91_CHIPSELECT_0 0x10000000 -#define AT91_CHIPSELECT_1 0x20000000 -#define AT91_CHIPSELECT_2 0x30000000 -#define AT91_CHIPSELECT_3 0x40000000 -#define AT91_CHIPSELECT_4 0x50000000 -#define AT91_CHIPSELECT_5 0x60000000 -#define AT91_CHIPSELECT_6 0x70000000 -#define AT91_CHIPSELECT_7 0x80000000 - -/* SDRAM */ -#define AT91_SDRAM_BASE AT91_CHIPSELECT_1 - -/* Clocks */ -#define AT91_SLOW_CLOCK 32768 /* slow clock */ - -#ifndef __ASSEMBLY__ -#include - -static inline unsigned int at91_sys_read(unsigned int reg_offset) -{ - void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS; - - return __raw_readl(addr + reg_offset); -} - -static inline void at91_sys_write(unsigned int reg_offset, unsigned long value) -{ - void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS; - - __raw_writel(value, addr + reg_offset); -} -#endif - -#endif diff --git a/include/asm-arm/arch-at91rm9200/io.h b/include/asm-arm/arch-at91rm9200/io.h deleted file mode 100644 index 88fd1bebcef3..000000000000 --- a/include/asm-arm/arch-at91rm9200/io.h +++ /dev/null @@ -1,32 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/io.h - * - * Copyright (C) 2003 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_IO_H -#define __ASM_ARCH_IO_H - -#include - -#define IO_SPACE_LIMIT 0xFFFFFFFF - -#define __io(a) ((void __iomem *)(a)) -#define __mem_pci(a) (a) - - -#endif diff --git a/include/asm-arm/arch-at91rm9200/irqs.h b/include/asm-arm/arch-at91rm9200/irqs.h deleted file mode 100644 index c0679eaefaf2..000000000000 --- a/include/asm-arm/arch-at91rm9200/irqs.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/irqs.h - * - * Copyright (C) 2004 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_IRQS_H -#define __ASM_ARCH_IRQS_H - -#include - -#define NR_AIC_IRQS 32 - - -/* - * Acknowledge interrupt with AIC after interrupt has been handled. - * (by kernel/irq.c) - */ -#define irq_finish(irq) do { at91_sys_write(AT91_AIC_EOICR, 0); } while (0) - - -/* - * IRQ interrupt symbols are the AT91xxx_ID_* symbols - * for IRQs handled directly through the AIC, or else the AT91_PIN_* - * symbols in gpio.h for ones handled indirectly as GPIOs. - * We make provision for 4 banks of GPIO. - */ -#define NR_IRQS (NR_AIC_IRQS + (4 * 32)) - -#endif diff --git a/include/asm-arm/arch-at91rm9200/memory.h b/include/asm-arm/arch-at91rm9200/memory.h deleted file mode 100644 index f985069e6d01..000000000000 --- a/include/asm-arm/arch-at91rm9200/memory.h +++ /dev/null @@ -1,39 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/memory.h - * - * Copyright (C) 2004 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_MEMORY_H -#define __ASM_ARCH_MEMORY_H - -#include - -#define PHYS_OFFSET (AT91_SDRAM_BASE) - - -/* - * Virtual view <-> DMA view memory address translations - * virt_to_bus: Used to translate the virtual address to an - * address suitable to be passed to set_dma_addr - * bus_to_virt: Used to convert an address for DMA operations - * to an address that the kernel can use. - */ -#define __virt_to_bus(x) __virt_to_phys(x) -#define __bus_to_virt(x) __phys_to_virt(x) - -#endif diff --git a/include/asm-arm/arch-at91rm9200/system.h b/include/asm-arm/arch-at91rm9200/system.h deleted file mode 100644 index 9c67130603b2..000000000000 --- a/include/asm-arm/arch-at91rm9200/system.h +++ /dev/null @@ -1,53 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/system.h - * - * Copyright (C) 2003 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_SYSTEM_H -#define __ASM_ARCH_SYSTEM_H - -#include -#include -#include - -static inline void arch_idle(void) -{ - /* - * Disable the processor clock. The processor will be automatically - * re-enabled by an interrupt or by a reset. - */ -// at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK); - - /* - * Set the processor (CP15) into 'Wait for Interrupt' mode. - * Unlike disabling the processor clock via the PMC (above) - * this allows the processor to be woken via JTAG. - */ - cpu_do_idle(); -} - -void (*at91_arch_reset)(void); - -static inline void arch_reset(char mode) -{ - /* call the CPU-specific reset function */ - if (at91_arch_reset) - (at91_arch_reset)(); -} - -#endif diff --git a/include/asm-arm/arch-at91rm9200/timex.h b/include/asm-arm/arch-at91rm9200/timex.h deleted file mode 100644 index faeca45a8d44..000000000000 --- a/include/asm-arm/arch-at91rm9200/timex.h +++ /dev/null @@ -1,37 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/timex.h - * - * Copyright (C) 2003 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_TIMEX_H -#define __ASM_ARCH_TIMEX_H - -#include - -#if defined(CONFIG_ARCH_AT91RM9200) - -#define CLOCK_TICK_RATE (AT91_SLOW_CLOCK) - -#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) - -#define AT91SAM9_MASTER_CLOCK 99300000 -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#endif - -#endif diff --git a/include/asm-arm/arch-at91rm9200/uncompress.h b/include/asm-arm/arch-at91rm9200/uncompress.h deleted file mode 100644 index 34b4b93fa015..000000000000 --- a/include/asm-arm/arch-at91rm9200/uncompress.h +++ /dev/null @@ -1,56 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/uncompress.h - * - * Copyright (C) 2003 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_UNCOMPRESS_H -#define __ASM_ARCH_UNCOMPRESS_H - -#include -#include - -/* - * The following code assumes the serial port has already been - * initialized by the bootloader. If you didn't setup a port in - * your bootloader then nothing will appear (which might be desired). - * - * This does not append a newline - */ -static void putc(int c) -{ - void __iomem *sys = (void __iomem *) AT91_BASE_SYS; /* physical address */ - - while (!(__raw_readl(sys + AT91_DBGU_SR) & AT91_DBGU_TXRDY)) - barrier(); - __raw_writel(c, sys + AT91_DBGU_THR); -} - -static inline void flush(void) -{ - void __iomem *sys = (void __iomem *) AT91_BASE_SYS; /* physical address */ - - /* wait for transmission to complete */ - while (!(__raw_readl(sys + AT91_DBGU_SR) & AT91_DBGU_TXEMPTY)) - barrier(); -} - -#define arch_decomp_setup() - -#define arch_decomp_wdog() - -#endif diff --git a/include/asm-arm/arch-at91rm9200/vmalloc.h b/include/asm-arm/arch-at91rm9200/vmalloc.h deleted file mode 100644 index 0a23b8c562b9..000000000000 --- a/include/asm-arm/arch-at91rm9200/vmalloc.h +++ /dev/null @@ -1,26 +0,0 @@ -/* - * include/asm-arm/arch-at91rm9200/vmalloc.h - * - * Copyright (C) 2003 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_VMALLOC_H -#define __ASM_ARCH_VMALLOC_H - -#define VMALLOC_END (AT91_VIRT_BASE & PGDIR_MASK) - -#endif diff --git a/include/asm-avr32/arch-at32ap/at91_pdc.h b/include/asm-avr32/arch-at32ap/at91_pdc.h index 79d6e02fa45e..a54adf52c65d 100644 --- a/include/asm-avr32/arch-at32ap/at91_pdc.h +++ b/include/asm-avr32/arch-at32ap/at91_pdc.h @@ -1,5 +1,5 @@ /* - * include/asm-arm/arch-at91rm9200/at91_pdc.h + * include/asm-arm/arch-at91/at91_pdc.h * * Copyright (C) 2005 Ivan Kokshaysky * Copyright (C) SAN People -- cgit v1.2.3 From d0760b3bc8ff9b34e3e2e166e2102548a24751b4 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 09:00:39 +0100 Subject: [ARM] 4143/1: AT91: Prepare for AT91SAM9263 support The Atmel AT91SAM9263 processor includes many more integrated peripherals than Atmel's previous ARM9-based AT91 processors, so this has necessitated a few changes to the core AT91 support. These changes are: * The system peripheral I/O region we remap has increased from 0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF. * The increased I/O region forces changes to entry-macro.S and debug-macro.S due to ARM's limited immediate offset addressing modes. * Maximum number of GPIO banks increases to 5. * 2 MMC controllers so the board-setup code needs to specify which controller it wishes to use when calling at91_add_device_mmc(). Original patch from Nicolas Ferre. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/at91rm9200_devices.c | 4 +- arch/arm/mach-at91/at91sam9260_devices.c | 4 +- arch/arm/mach-at91/at91sam9261_devices.c | 4 +- arch/arm/mach-at91/board-carmeva.c | 2 +- arch/arm/mach-at91/board-csb337.c | 2 +- arch/arm/mach-at91/board-dk.c | 2 +- arch/arm/mach-at91/board-eb9200.c | 2 +- arch/arm/mach-at91/board-ek.c | 2 +- arch/arm/mach-at91/board-kb9202.c | 2 +- arch/arm/mach-at91/board-sam9260ek.c | 4 +- arch/arm/mach-at91/board-sam9261ek.c | 4 +- include/asm-arm/arch-at91/at91sam9260_matrix.h | 2 +- include/asm-arm/arch-at91/board.h | 3 +- include/asm-arm/arch-at91/debug-macro.S | 16 +++---- include/asm-arm/arch-at91/entry-macro.S | 10 ++--- include/asm-arm/arch-at91/gpio.h | 59 +++++++++++++++----------- include/asm-arm/arch-at91/hardware.h | 8 ++-- include/asm-arm/arch-at91/irqs.h | 4 +- 18 files changed, 72 insertions(+), 62 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index a06498ccc826..077c81f9bc56 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -315,7 +315,7 @@ static struct platform_device at91rm9200_mmc_device = { .num_resources = ARRAY_SIZE(mmc_resources), }; -void __init at91_add_device_mmc(struct at91_mmc_data *data) +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) { if (!data) return; @@ -361,7 +361,7 @@ void __init at91_add_device_mmc(struct at91_mmc_data *data) platform_device_register(&at91rm9200_mmc_device); } #else -void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 4adff70b9ba0..b5d8968e29a7 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -229,7 +229,7 @@ static struct platform_device at91sam9260_mmc_device = { .num_resources = ARRAY_SIZE(mmc_resources), }; -void __init at91_add_device_mmc(struct at91_mmc_data *data) +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) { if (!data) return; @@ -275,7 +275,7 @@ void __init at91_add_device_mmc(struct at91_mmc_data *data) platform_device_register(&at91sam9260_mmc_device); } #else -void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index 3249de08d1f3..b2f6d33d0f8c 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -159,7 +159,7 @@ static struct platform_device at91sam9261_mmc_device = { .num_resources = ARRAY_SIZE(mmc_resources), }; -void __init at91_add_device_mmc(struct at91_mmc_data *data) +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) { if (!data) return; @@ -192,7 +192,7 @@ void __init at91_add_device_mmc(struct at91_mmc_data *data) platform_device_register(&at91sam9261_mmc_device); } #else -void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} #endif diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index a0815322f685..b4518619063a 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -134,7 +134,7 @@ static void __init carmeva_board_init(void) /* Compact Flash */ // at91_add_device_cf(&carmeva_cf_data); /* MMC */ - at91_add_device_mmc(&carmeva_mmc_data); + at91_add_device_mmc(0, &carmeva_mmc_data); } MACHINE_START(CARMEVA, "Carmeva") diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index 45d6d9b8f5e9..871c6609d6ec 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -130,7 +130,7 @@ static void __init csb337_board_init(void) /* SPI */ at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); /* MMC */ - at91_add_device_mmc(&csb337_mmc_data); + at91_add_device_mmc(0, &csb337_mmc_data); } MACHINE_START(CSB337, "Cogent CSB337") diff --git a/arch/arm/mach-at91/board-dk.c b/arch/arm/mach-at91/board-dk.c index 7401dbe1b474..6043c38c0a9e 100644 --- a/arch/arm/mach-at91/board-dk.c +++ b/arch/arm/mach-at91/board-dk.c @@ -194,7 +194,7 @@ static void __init dk_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(&dk_mmc_data); + at91_add_device_mmc(0, &dk_mmc_data); #endif /* NAND */ at91_add_device_nand(&dk_nand_data); diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index 56d5ef63e04e..20458b5548f0 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -109,7 +109,7 @@ static void __init eb9200_board_init(void) at91_add_device_spi(NULL, 0); /* MMC */ /* only supports 1 or 4 bit interface, not wired through to SPI */ - at91_add_device_mmc(&eb9200_mmc_data); + at91_add_device_mmc(0, &eb9200_mmc_data); } MACHINE_START(ATEB9200, "Embest ATEB9200") diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-ek.c index 0f589dd7d1a9..322fdd75a1e4 100644 --- a/arch/arm/mach-at91/board-ek.c +++ b/arch/arm/mach-at91/board-ek.c @@ -154,7 +154,7 @@ static void __init ek_board_init(void) #else /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(&ek_mmc_data); + at91_add_device_mmc(0, &ek_mmc_data); #endif /* NOR Flash */ platform_device_register(&ek_flash); diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index 17e68f5efb13..76f6e1e553ea 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -122,7 +122,7 @@ static void __init kb9202_board_init(void) /* USB Device */ at91_add_device_udc(&kb9202_udc_data); /* MMC */ - at91_add_device_mmc(&kb9202_mmc_data); + at91_add_device_mmc(0, &kb9202_mmc_data); /* I2C */ at91_add_device_i2c(); /* SPI */ diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index 6ae272d224e5..57fb4499d969 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -1,5 +1,5 @@ /* - * linux/arch/arm/mach-at91/board-ek.c + * linux/arch/arm/mach-at91/board-sam9260ek.c * * Copyright (C) 2005 SAN People * Copyright (C) 2006 Atmel @@ -187,7 +187,7 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ - at91_add_device_mmc(&ek_mmc_data); + at91_add_device_mmc(0, &ek_mmc_data); } MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 25d626348e6d..b7e772467cf6 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -1,5 +1,5 @@ /* - * linux/arch/arm/mach-at91/board-ek.c + * linux/arch/arm/mach-at91/board-sam9261ek.c * * Copyright (C) 2005 SAN People * Copyright (C) 2006 Atmel @@ -243,7 +243,7 @@ static void __init ek_board_init(void) at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); #else /* MMC */ - at91_add_device_mmc(&ek_mmc_data); + at91_add_device_mmc(0, &ek_mmc_data); #endif } diff --git a/include/asm-arm/arch-at91/at91sam9260_matrix.h b/include/asm-arm/arch-at91/at91sam9260_matrix.h index 573e97a47d22..aacb1e976422 100644 --- a/include/asm-arm/arch-at91/at91sam9260_matrix.h +++ b/include/asm-arm/arch-at91/at91sam9260_matrix.h @@ -18,7 +18,7 @@ #define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */ #define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */ #define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */ -#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x04) /* Master Configuration Register 5 */ +#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */ #define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ #define AT91_MATRIX_ULBT_INFINITE (0 << 0) #define AT91_MATRIX_ULBT_SINGLE (1 << 0) diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index bf1afd0081b6..7b9903c2c447 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -60,7 +60,7 @@ struct at91_mmc_data { u8 wp_pin; /* (SD) writeprotect detect */ u8 vcc_pin; /* power switching (high == on) */ }; -extern void __init at91_add_device_mmc(struct at91_mmc_data *data); +extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data); /* Ethernet */ struct at91_eth_data { @@ -76,6 +76,7 @@ extern void __init at91_add_device_eth(struct at91_eth_data *data); /* USB Host */ struct at91_usbh_data { u8 ports; /* number of ports on root hub */ + u8 vbus_pin[]; /* port power-control pin */ }; extern void __init at91_add_device_usbh(struct at91_usbh_data *data); diff --git a/include/asm-arm/arch-at91/debug-macro.S b/include/asm-arm/arch-at91/debug-macro.S index 20721ef1ed1b..13e9f5e1d4ff 100644 --- a/include/asm-arm/arch-at91/debug-macro.S +++ b/include/asm-arm/arch-at91/debug-macro.S @@ -16,24 +16,24 @@ .macro addruart,rx mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =AT91_BASE_SYS @ System peripherals (phys address) - ldrne \rx, =AT91_VA_BASE_SYS @ System peripherals (virt address) + tst \rx, #1 @ MMU enabled? + ldreq \rx, =(AT91_BASE_SYS + AT91_DBGU) @ System peripherals (phys address) + ldrne \rx, =(AT91_VA_BASE_SYS + AT91_DBGU) @ System peripherals (virt address) .endm .macro senduart,rd,rx - strb \rd, [\rx, #AT91_DBGU_THR] @ Write to Transmitter Holding Register + strb \rd, [\rx, #(AT91_DBGU_THR - AT91_DBGU)] @ Write to Transmitter Holding Register .endm .macro waituart,rd,rx -1001: ldr \rd, [\rx, #AT91_DBGU_SR] @ Read Status Register - tst \rd, #AT91_DBGU_TXRDY @ DBGU_TXRDY = 1 when ready to transmit +1001: ldr \rd, [\rx, #(AT91_DBGU_SR - AT91_DBGU)] @ Read Status Register + tst \rd, #AT91_DBGU_TXRDY @ DBGU_TXRDY = 1 when ready to transmit beq 1001b .endm .macro busyuart,rd,rx -1001: ldr \rd, [\rx, #AT91_DBGU_SR] @ Read Status Register - tst \rd, #AT91_DBGU_TXEMPTY @ DBGU_TXEMPTY = 1 when transmission complete +1001: ldr \rd, [\rx, #(AT91_DBGU_SR - AT91_DBGU)] @ Read Status Register + tst \rd, #AT91_DBGU_TXEMPTY @ DBGU_TXEMPTY = 1 when transmission complete beq 1001b .endm diff --git a/include/asm-arm/arch-at91/entry-macro.S b/include/asm-arm/arch-at91/entry-macro.S index a6f33832a178..76c8cccf73aa 100644 --- a/include/asm-arm/arch-at91/entry-macro.S +++ b/include/asm-arm/arch-at91/entry-macro.S @@ -17,10 +17,10 @@ .endm .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \base, =(AT91_VA_BASE_SYS) @ base virtual address of SYS peripherals - ldr \irqnr, [\base, #AT91_AIC_IVR] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt) - ldr \irqstat, [\base, #AT91_AIC_ISR] @ read interrupt source number - teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt - streq \tmp, [\base, #AT91_AIC_EOICR] @ not going to be handled further, then ACK it now. + ldr \base, =(AT91_VA_BASE_SYS + AT91_AIC) @ base virtual address of AIC peripheral + ldr \irqnr, [\base, #(AT91_AIC_IVR - AT91_AIC)] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt) + ldr \irqstat, [\base, #(AT91_AIC_ISR - AT91_AIC)] @ read interrupt source number + teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt + streq \tmp, [\base, #(AT91_AIC_EOICR - AT91_AIC)] @ not going to be handled further, then ACK it now. .endm diff --git a/include/asm-arm/arch-at91/gpio.h b/include/asm-arm/arch-at91/gpio.h index 6d1a5eb34704..256f9b200ab2 100644 --- a/include/asm-arm/arch-at91/gpio.h +++ b/include/asm-arm/arch-at91/gpio.h @@ -17,7 +17,7 @@ #define PIN_BASE NR_AIC_IRQS -#define MAX_GPIO_BANKS 4 +#define MAX_GPIO_BANKS 5 /* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */ @@ -26,37 +26,31 @@ #define AT91_PIN_PA2 (PIN_BASE + 0x00 + 2) #define AT91_PIN_PA3 (PIN_BASE + 0x00 + 3) #define AT91_PIN_PA4 (PIN_BASE + 0x00 + 4) - #define AT91_PIN_PA5 (PIN_BASE + 0x00 + 5) #define AT91_PIN_PA6 (PIN_BASE + 0x00 + 6) #define AT91_PIN_PA7 (PIN_BASE + 0x00 + 7) #define AT91_PIN_PA8 (PIN_BASE + 0x00 + 8) #define AT91_PIN_PA9 (PIN_BASE + 0x00 + 9) - #define AT91_PIN_PA10 (PIN_BASE + 0x00 + 10) #define AT91_PIN_PA11 (PIN_BASE + 0x00 + 11) #define AT91_PIN_PA12 (PIN_BASE + 0x00 + 12) #define AT91_PIN_PA13 (PIN_BASE + 0x00 + 13) #define AT91_PIN_PA14 (PIN_BASE + 0x00 + 14) - #define AT91_PIN_PA15 (PIN_BASE + 0x00 + 15) #define AT91_PIN_PA16 (PIN_BASE + 0x00 + 16) #define AT91_PIN_PA17 (PIN_BASE + 0x00 + 17) #define AT91_PIN_PA18 (PIN_BASE + 0x00 + 18) #define AT91_PIN_PA19 (PIN_BASE + 0x00 + 19) - #define AT91_PIN_PA20 (PIN_BASE + 0x00 + 20) #define AT91_PIN_PA21 (PIN_BASE + 0x00 + 21) #define AT91_PIN_PA22 (PIN_BASE + 0x00 + 22) #define AT91_PIN_PA23 (PIN_BASE + 0x00 + 23) #define AT91_PIN_PA24 (PIN_BASE + 0x00 + 24) - #define AT91_PIN_PA25 (PIN_BASE + 0x00 + 25) #define AT91_PIN_PA26 (PIN_BASE + 0x00 + 26) #define AT91_PIN_PA27 (PIN_BASE + 0x00 + 27) #define AT91_PIN_PA28 (PIN_BASE + 0x00 + 28) #define AT91_PIN_PA29 (PIN_BASE + 0x00 + 29) - #define AT91_PIN_PA30 (PIN_BASE + 0x00 + 30) #define AT91_PIN_PA31 (PIN_BASE + 0x00 + 31) @@ -65,37 +59,31 @@ #define AT91_PIN_PB2 (PIN_BASE + 0x20 + 2) #define AT91_PIN_PB3 (PIN_BASE + 0x20 + 3) #define AT91_PIN_PB4 (PIN_BASE + 0x20 + 4) - #define AT91_PIN_PB5 (PIN_BASE + 0x20 + 5) #define AT91_PIN_PB6 (PIN_BASE + 0x20 + 6) #define AT91_PIN_PB7 (PIN_BASE + 0x20 + 7) #define AT91_PIN_PB8 (PIN_BASE + 0x20 + 8) #define AT91_PIN_PB9 (PIN_BASE + 0x20 + 9) - #define AT91_PIN_PB10 (PIN_BASE + 0x20 + 10) #define AT91_PIN_PB11 (PIN_BASE + 0x20 + 11) #define AT91_PIN_PB12 (PIN_BASE + 0x20 + 12) #define AT91_PIN_PB13 (PIN_BASE + 0x20 + 13) #define AT91_PIN_PB14 (PIN_BASE + 0x20 + 14) - #define AT91_PIN_PB15 (PIN_BASE + 0x20 + 15) #define AT91_PIN_PB16 (PIN_BASE + 0x20 + 16) #define AT91_PIN_PB17 (PIN_BASE + 0x20 + 17) #define AT91_PIN_PB18 (PIN_BASE + 0x20 + 18) #define AT91_PIN_PB19 (PIN_BASE + 0x20 + 19) - #define AT91_PIN_PB20 (PIN_BASE + 0x20 + 20) #define AT91_PIN_PB21 (PIN_BASE + 0x20 + 21) #define AT91_PIN_PB22 (PIN_BASE + 0x20 + 22) #define AT91_PIN_PB23 (PIN_BASE + 0x20 + 23) #define AT91_PIN_PB24 (PIN_BASE + 0x20 + 24) - #define AT91_PIN_PB25 (PIN_BASE + 0x20 + 25) #define AT91_PIN_PB26 (PIN_BASE + 0x20 + 26) #define AT91_PIN_PB27 (PIN_BASE + 0x20 + 27) #define AT91_PIN_PB28 (PIN_BASE + 0x20 + 28) #define AT91_PIN_PB29 (PIN_BASE + 0x20 + 29) - #define AT91_PIN_PB30 (PIN_BASE + 0x20 + 30) #define AT91_PIN_PB31 (PIN_BASE + 0x20 + 31) @@ -104,37 +92,31 @@ #define AT91_PIN_PC2 (PIN_BASE + 0x40 + 2) #define AT91_PIN_PC3 (PIN_BASE + 0x40 + 3) #define AT91_PIN_PC4 (PIN_BASE + 0x40 + 4) - #define AT91_PIN_PC5 (PIN_BASE + 0x40 + 5) #define AT91_PIN_PC6 (PIN_BASE + 0x40 + 6) #define AT91_PIN_PC7 (PIN_BASE + 0x40 + 7) #define AT91_PIN_PC8 (PIN_BASE + 0x40 + 8) #define AT91_PIN_PC9 (PIN_BASE + 0x40 + 9) - #define AT91_PIN_PC10 (PIN_BASE + 0x40 + 10) #define AT91_PIN_PC11 (PIN_BASE + 0x40 + 11) #define AT91_PIN_PC12 (PIN_BASE + 0x40 + 12) #define AT91_PIN_PC13 (PIN_BASE + 0x40 + 13) #define AT91_PIN_PC14 (PIN_BASE + 0x40 + 14) - #define AT91_PIN_PC15 (PIN_BASE + 0x40 + 15) #define AT91_PIN_PC16 (PIN_BASE + 0x40 + 16) #define AT91_PIN_PC17 (PIN_BASE + 0x40 + 17) #define AT91_PIN_PC18 (PIN_BASE + 0x40 + 18) #define AT91_PIN_PC19 (PIN_BASE + 0x40 + 19) - #define AT91_PIN_PC20 (PIN_BASE + 0x40 + 20) #define AT91_PIN_PC21 (PIN_BASE + 0x40 + 21) #define AT91_PIN_PC22 (PIN_BASE + 0x40 + 22) #define AT91_PIN_PC23 (PIN_BASE + 0x40 + 23) #define AT91_PIN_PC24 (PIN_BASE + 0x40 + 24) - #define AT91_PIN_PC25 (PIN_BASE + 0x40 + 25) #define AT91_PIN_PC26 (PIN_BASE + 0x40 + 26) #define AT91_PIN_PC27 (PIN_BASE + 0x40 + 27) #define AT91_PIN_PC28 (PIN_BASE + 0x40 + 28) #define AT91_PIN_PC29 (PIN_BASE + 0x40 + 29) - #define AT91_PIN_PC30 (PIN_BASE + 0x40 + 30) #define AT91_PIN_PC31 (PIN_BASE + 0x40 + 31) @@ -143,40 +125,67 @@ #define AT91_PIN_PD2 (PIN_BASE + 0x60 + 2) #define AT91_PIN_PD3 (PIN_BASE + 0x60 + 3) #define AT91_PIN_PD4 (PIN_BASE + 0x60 + 4) - #define AT91_PIN_PD5 (PIN_BASE + 0x60 + 5) #define AT91_PIN_PD6 (PIN_BASE + 0x60 + 6) #define AT91_PIN_PD7 (PIN_BASE + 0x60 + 7) #define AT91_PIN_PD8 (PIN_BASE + 0x60 + 8) #define AT91_PIN_PD9 (PIN_BASE + 0x60 + 9) - #define AT91_PIN_PD10 (PIN_BASE + 0x60 + 10) #define AT91_PIN_PD11 (PIN_BASE + 0x60 + 11) #define AT91_PIN_PD12 (PIN_BASE + 0x60 + 12) #define AT91_PIN_PD13 (PIN_BASE + 0x60 + 13) #define AT91_PIN_PD14 (PIN_BASE + 0x60 + 14) - #define AT91_PIN_PD15 (PIN_BASE + 0x60 + 15) #define AT91_PIN_PD16 (PIN_BASE + 0x60 + 16) #define AT91_PIN_PD17 (PIN_BASE + 0x60 + 17) #define AT91_PIN_PD18 (PIN_BASE + 0x60 + 18) #define AT91_PIN_PD19 (PIN_BASE + 0x60 + 19) - #define AT91_PIN_PD20 (PIN_BASE + 0x60 + 20) #define AT91_PIN_PD21 (PIN_BASE + 0x60 + 21) #define AT91_PIN_PD22 (PIN_BASE + 0x60 + 22) #define AT91_PIN_PD23 (PIN_BASE + 0x60 + 23) #define AT91_PIN_PD24 (PIN_BASE + 0x60 + 24) - #define AT91_PIN_PD25 (PIN_BASE + 0x60 + 25) #define AT91_PIN_PD26 (PIN_BASE + 0x60 + 26) #define AT91_PIN_PD27 (PIN_BASE + 0x60 + 27) #define AT91_PIN_PD28 (PIN_BASE + 0x60 + 28) #define AT91_PIN_PD29 (PIN_BASE + 0x60 + 29) - #define AT91_PIN_PD30 (PIN_BASE + 0x60 + 30) #define AT91_PIN_PD31 (PIN_BASE + 0x60 + 31) +#define AT91_PIN_PE0 (PIN_BASE + 0x80 + 0) +#define AT91_PIN_PE1 (PIN_BASE + 0x80 + 1) +#define AT91_PIN_PE2 (PIN_BASE + 0x80 + 2) +#define AT91_PIN_PE3 (PIN_BASE + 0x80 + 3) +#define AT91_PIN_PE4 (PIN_BASE + 0x80 + 4) +#define AT91_PIN_PE5 (PIN_BASE + 0x80 + 5) +#define AT91_PIN_PE6 (PIN_BASE + 0x80 + 6) +#define AT91_PIN_PE7 (PIN_BASE + 0x80 + 7) +#define AT91_PIN_PE8 (PIN_BASE + 0x80 + 8) +#define AT91_PIN_PE9 (PIN_BASE + 0x80 + 9) +#define AT91_PIN_PE10 (PIN_BASE + 0x80 + 10) +#define AT91_PIN_PE11 (PIN_BASE + 0x80 + 11) +#define AT91_PIN_PE12 (PIN_BASE + 0x80 + 12) +#define AT91_PIN_PE13 (PIN_BASE + 0x80 + 13) +#define AT91_PIN_PE14 (PIN_BASE + 0x80 + 14) +#define AT91_PIN_PE15 (PIN_BASE + 0x80 + 15) +#define AT91_PIN_PE16 (PIN_BASE + 0x80 + 16) +#define AT91_PIN_PE17 (PIN_BASE + 0x80 + 17) +#define AT91_PIN_PE18 (PIN_BASE + 0x80 + 18) +#define AT91_PIN_PE19 (PIN_BASE + 0x80 + 19) +#define AT91_PIN_PE20 (PIN_BASE + 0x80 + 20) +#define AT91_PIN_PE21 (PIN_BASE + 0x80 + 21) +#define AT91_PIN_PE22 (PIN_BASE + 0x80 + 22) +#define AT91_PIN_PE23 (PIN_BASE + 0x80 + 23) +#define AT91_PIN_PE24 (PIN_BASE + 0x80 + 24) +#define AT91_PIN_PE25 (PIN_BASE + 0x80 + 25) +#define AT91_PIN_PE26 (PIN_BASE + 0x80 + 26) +#define AT91_PIN_PE27 (PIN_BASE + 0x80 + 27) +#define AT91_PIN_PE28 (PIN_BASE + 0x80 + 28) +#define AT91_PIN_PE29 (PIN_BASE + 0x80 + 29) +#define AT91_PIN_PE30 (PIN_BASE + 0x80 + 30) +#define AT91_PIN_PE31 (PIN_BASE + 0x80 + 31) + #ifndef __ASSEMBLY__ /* setup setup routines, called from board init or driver probe() */ extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup); diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h index ccb7c7285b42..1637fc4a0d8f 100644 --- a/include/asm-arm/arch-at91/hardware.h +++ b/include/asm-arm/arch-at91/hardware.h @@ -28,15 +28,15 @@ /* - * Remap the peripherals from address 0xFFFA0000 .. 0xFFFFFFFF - * to 0xFEFA0000 .. 0xFF000000. (384Kb) + * Remap the peripherals from address 0xFFF78000 .. 0xFFFFFFFF + * to 0xFEF78000 .. 0xFF000000. (5444Kb) */ -#define AT91_IO_PHYS_BASE 0xFFFA0000 +#define AT91_IO_PHYS_BASE 0xFFF78000 #define AT91_IO_SIZE (0xFFFFFFFF - AT91_IO_PHYS_BASE + 1) #define AT91_IO_VIRT_BASE (0xFF000000 - AT91_IO_SIZE) /* Convert a physical IO address to virtual IO address */ -#define AT91_IO_P2V(x) ((x) - AT91_IO_PHYS_BASE + AT91_IO_VIRT_BASE) +#define AT91_IO_P2V(x) ((x) - AT91_IO_PHYS_BASE + AT91_IO_VIRT_BASE) /* * Virtual to Physical Address mapping for IO devices. diff --git a/include/asm-arm/arch-at91/irqs.h b/include/asm-arm/arch-at91/irqs.h index f041c98c5337..1ffa3bb9a9c1 100644 --- a/include/asm-arm/arch-at91/irqs.h +++ b/include/asm-arm/arch-at91/irqs.h @@ -37,8 +37,8 @@ * IRQ interrupt symbols are the AT91xxx_ID_* symbols * for IRQs handled directly through the AIC, or else the AT91_PIN_* * symbols in gpio.h for ones handled indirectly as GPIOs. - * We make provision for 4 banks of GPIO. + * We make provision for 5 banks of GPIO. */ -#define NR_IRQS (NR_AIC_IRQS + (4 * 32)) +#define NR_IRQS (NR_AIC_IRQS + (5 * 32)) #endif -- cgit v1.2.3 From b2c6561605da4802886cafe96432b8e2968e9edc Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 09:42:40 +0100 Subject: [ARM] 4145/2: AT91: Add support for AT91SAM9263 processor Add support for the Atmel AT91SAM9263 processor. It is similar to the AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc. Original patch from Nicolas Ferre. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/Kconfig | 3 + arch/arm/mach-at91/Makefile | 1 + arch/arm/mach-at91/at91sam9263.c | 313 ++++++++++ arch/arm/mach-at91/at91sam9263_devices.c | 818 +++++++++++++++++++++++++ arch/arm/mach-at91/clock.c | 2 +- arch/arm/mach-at91/generic.h | 2 + arch/arm/mach-at91/pm.c | 2 + arch/arm/mm/Kconfig | 4 +- drivers/usb/gadget/at91_udc.c | 4 +- include/asm-arm/arch-at91/at91sam9263.h | 131 ++++ include/asm-arm/arch-at91/at91sam9263_matrix.h | 129 ++++ include/asm-arm/arch-at91/at91sam926x_mc.h | 7 + include/asm-arm/arch-at91/cpu.h | 7 + include/asm-arm/arch-at91/hardware.h | 2 + include/asm-arm/arch-at91/timex.h | 5 + 15 files changed, 1425 insertions(+), 5 deletions(-) create mode 100644 arch/arm/mach-at91/at91sam9263.c create mode 100644 arch/arm/mach-at91/at91sam9263_devices.c create mode 100644 include/asm-arm/arch-at91/at91sam9263.h create mode 100644 include/asm-arm/arch-at91/at91sam9263_matrix.h (limited to 'arch') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 9f11db8af233..2499385e22da 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -14,6 +14,9 @@ config ARCH_AT91SAM9260 config ARCH_AT91SAM9261 bool "AT91SAM9261" +config ARCH_AT91SAM9263 + bool "AT91SAM9263" + endchoice # ---------------------------------------------------------- diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index cf777007847a..2fd4cd4a57f8 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -13,6 +13,7 @@ obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devices.o obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o +obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o # AT91RM9200 board-specific support obj-$(CONFIG_MACH_ONEARM) += board-1arm.o diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c new file mode 100644 index 000000000000..fae6a821a61b --- /dev/null +++ b/arch/arm/mach-at91/at91sam9263.c @@ -0,0 +1,313 @@ +/* + * arch/arm/mach-at91/at91sam9263.c + * + * Copyright (C) 2007 Atmel Corporation. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" +#include "clock.h" + +static struct map_desc at91sam9263_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91_BASE_SYS), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9263_SRAM0_SIZE, + .pfn = __phys_to_pfn(AT91SAM9263_SRAM0_BASE), + .length = AT91SAM9263_SRAM0_SIZE, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9263_SRAM0_SIZE - AT91SAM9263_SRAM1_SIZE, + .pfn = __phys_to_pfn(AT91SAM9263_SRAM1_BASE), + .length = AT91SAM9263_SRAM1_SIZE, + .type = MT_DEVICE, + }, +}; + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91SAM9263_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91SAM9263_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioCDE_clk = { + .name = "pioCDE_clk", + .pmc_mask = 1 << AT91SAM9263_ID_PIOCDE, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91SAM9263_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91SAM9263_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91SAM9263_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc0_clk = { + .name = "mci0_clk", + .pmc_mask = 1 << AT91SAM9263_ID_MCI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc1_clk = { + .name = "mci1_clk", + .pmc_mask = 1 << AT91SAM9263_ID_MCI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi_clk = { + .name = "twi_clk", + .pmc_mask = 1 << AT91SAM9263_ID_TWI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi0_clk = { + .name = "spi0_clk", + .pmc_mask = 1 << AT91SAM9263_ID_SPI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi1_clk = { + .name = "spi1_clk", + .pmc_mask = 1 << AT91SAM9263_ID_SPI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tcb_clk = { + .name = "tcb_clk", + .pmc_mask = 1 << AT91SAM9263_ID_TCB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ether_clk = { + .name = "ether_clk", + .pmc_mask = 1 << AT91SAM9263_ID_EMAC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk udc_clk = { + .name = "udc_clk", + .pmc_mask = 1 << AT91SAM9263_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk isi_clk = { + .name = "isi_clk", + .pmc_mask = 1 << AT91SAM9263_ID_ISI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk lcdc_clk = { + .name = "lcdc_clk", + .pmc_mask = 1 << AT91SAM9263_ID_ISI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .pmc_mask = 1 << AT91SAM9263_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioCDE_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &mmc0_clk, + &mmc1_clk, + // can + &twi_clk, + &spi0_clk, + &spi1_clk, + // ssc0 .. ssc1 + // ac97 + &tcb_clk, + // pwmc + ðer_clk, + // 2dge + &udc_clk, + &isi_clk, + &lcdc_clk, + // dma + &ohci_clk, + // irq0 .. irq1 +}; + +/* + * The four programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; +static struct clk pck2 = { + .name = "pck2", + .pmc_mask = AT91_PMC_PCK2, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 2, +}; +static struct clk pck3 = { + .name = "pck3", + .pmc_mask = AT91_PMC_PCK3, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 3, +}; + +static void __init at91sam9263_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); + clk_register(&pck2); + clk_register(&pck3); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91sam9263_gpio[] = { + { + .id = AT91SAM9263_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91SAM9263_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91SAM9263_ID_PIOCDE, + .offset = AT91_PIOC, + .clock = &pioCDE_clk, + }, { + .id = AT91SAM9263_ID_PIOCDE, + .offset = AT91_PIOD, + .clock = &pioCDE_clk, + }, { + .id = AT91SAM9263_ID_PIOCDE, + .offset = AT91_PIOE, + .clock = &pioCDE_clk, + } +}; + +static void at91sam9263_reset(void) +{ + at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); +} + + +/* -------------------------------------------------------------------- + * AT91SAM9263 processor initialization + * -------------------------------------------------------------------- */ + +void __init at91sam9263_initialize(unsigned long main_clock) +{ + /* Map peripherals */ + iotable_init(at91sam9263_io_desc, ARRAY_SIZE(at91sam9263_io_desc)); + + at91_arch_reset = at91sam9263_reset; + at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91sam9263_register_clocks(); + + /* Register GPIO subsystem */ + at91_gpio_init(at91sam9263_gpio, 5); +} + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller (FIQ) */ + 7, /* System Peripherals */ + 0, /* Parallel IO Controller A */ + 0, /* Parallel IO Controller B */ + 0, /* Parallel IO Controller C, D and E */ + 0, + 0, + 6, /* USART 0 */ + 6, /* USART 1 */ + 6, /* USART 2 */ + 0, /* Multimedia Card Interface 0 */ + 0, /* Multimedia Card Interface 1 */ + 4, /* CAN */ + 0, /* Two-Wire Interface */ + 6, /* Serial Peripheral Interface 0 */ + 6, /* Serial Peripheral Interface 1 */ + 5, /* Serial Synchronous Controller 0 */ + 5, /* Serial Synchronous Controller 1 */ + 6, /* AC97 Controller */ + 0, /* Timer Counter 0, 1 and 2 */ + 0, /* Pulse Width Modulation Controller */ + 3, /* Ethernet */ + 0, + 0, /* 2D Graphic Engine */ + 3, /* USB Device Port */ + 0, /* Image Sensor Interface */ + 3, /* LDC Controller */ + 0, /* DMA Controller */ + 0, + 3, /* USB Host port */ + 0, /* Advanced Interrupt Controller (IRQ0) */ + 0, /* Advanced Interrupt Controller (IRQ1) */ +}; + +void __init at91sam9263_init_interrupts(unsigned int priority[NR_AIC_IRQS]) +{ + if (!priority) + priority = at91sam9263_default_irq_priority; + + /* Initialize the AIC interrupt controller */ + at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); +} diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c new file mode 100644 index 000000000000..d9af7ca58bce --- /dev/null +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -0,0 +1,818 @@ +/* + * arch/arm/mach-at91/at91sam9263_devices.c + * + * Copyright (C) 2007 Atmel Corporation. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include +#include + +#include + +#include +#include +#include +#include +#include + +#include "generic.h" + +#define SZ_512 0x00000200 +#define SZ_256 0x00000100 +#define SZ_16 0x00000010 + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource usbh_resources[] = { + [0] = { + .start = AT91SAM9263_UHP_BASE, + .end = AT91SAM9263_UHP_BASE + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_UHP, + .end = AT91SAM9263_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91_usbh_device = { + .name = "at91_ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = usbh_resources, + .num_resources = ARRAY_SIZE(usbh_resources), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + int i; + + if (!data) + return; + + /* Enable VBus control for UHP ports */ + for (i = 0; i < data->ports; i++) { + if (data->vbus_pin[i]) + at91_set_gpio_output(data->vbus_pin[i], 0); + } + + usbh_data = *data; + platform_device_register(&at91_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource udc_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_UDP, + .end = AT91SAM9263_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_UDP, + .end = AT91SAM9263_ID_UDP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = udc_resources, + .num_resources = ARRAY_SIZE(udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + + /* Pullup pin is handled internally by USB device peripheral */ + + udc_data = *data; + platform_device_register(&at91_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Ethernet + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) +static u64 eth_dmamask = 0xffffffffUL; +static struct at91_eth_data eth_data; + +static struct resource eth_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_EMAC, + .end = AT91SAM9263_BASE_EMAC + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_EMAC, + .end = AT91SAM9263_ID_EMAC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_eth_device = { + .name = "macb", + .id = -1, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = ð_data, + }, + .resource = eth_resources, + .num_resources = ARRAY_SIZE(eth_resources), +}; + +void __init at91_add_device_eth(struct at91_eth_data *data) +{ + if (!data) + return; + + if (data->phy_irq_pin) { + at91_set_gpio_input(data->phy_irq_pin, 0); + at91_set_deglitch(data->phy_irq_pin, 1); + } + + /* Pins used for MII and RMII */ + at91_set_A_periph(AT91_PIN_PE21, 0); /* ETXCK_EREFCK */ + at91_set_B_periph(AT91_PIN_PC25, 0); /* ERXDV */ + at91_set_A_periph(AT91_PIN_PE25, 0); /* ERX0 */ + at91_set_A_periph(AT91_PIN_PE26, 0); /* ERX1 */ + at91_set_A_periph(AT91_PIN_PE27, 0); /* ERXER */ + at91_set_A_periph(AT91_PIN_PE28, 0); /* ETXEN */ + at91_set_A_periph(AT91_PIN_PE23, 0); /* ETX0 */ + at91_set_A_periph(AT91_PIN_PE24, 0); /* ETX1 */ + at91_set_A_periph(AT91_PIN_PE30, 0); /* EMDIO */ + at91_set_A_periph(AT91_PIN_PE29, 0); /* EMDC */ + + if (!data->is_rmii) { + at91_set_A_periph(AT91_PIN_PE22, 0); /* ECRS */ + at91_set_B_periph(AT91_PIN_PC26, 0); /* ECOL */ + at91_set_B_periph(AT91_PIN_PC22, 0); /* ERX2 */ + at91_set_B_periph(AT91_PIN_PC23, 0); /* ERX3 */ + at91_set_B_periph(AT91_PIN_PC27, 0); /* ERXCK */ + at91_set_B_periph(AT91_PIN_PC20, 0); /* ETX2 */ + at91_set_B_periph(AT91_PIN_PC21, 0); /* ETX3 */ + at91_set_B_periph(AT91_PIN_PC24, 0); /* ETXER */ + } + + eth_data = *data; + platform_device_register(&at91sam9263_eth_device); +} +#else +void __init at91_add_device_eth(struct at91_eth_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc0_data, mmc1_data; + +static struct resource mmc0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI0, + .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI0, + .end = AT91SAM9263_ID_MCI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc0_device = { + .name = "at91_mci", + .id = 0, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc0_data, + }, + .resource = mmc0_resources, + .num_resources = ARRAY_SIZE(mmc0_resources), +}; + +static struct resource mmc1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_MCI1, + .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_MCI1, + .end = AT91SAM9263_ID_MCI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_mmc1_device = { + .name = "at91_mci", + .id = 1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc1_data, + }, + .resource = mmc1_resources, + .num_resources = ARRAY_SIZE(mmc1_resources), +}; + +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + + if (mmc_id == 0) { /* MCI0 */ + /* CLK */ + at91_set_A_periph(AT91_PIN_PA12, 0); + + if (data->slot_b) { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA16, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA17, 1); + if (data->wire4) { + at91_set_A_periph(AT91_PIN_PA18, 1); + at91_set_A_periph(AT91_PIN_PA19, 1); + at91_set_A_periph(AT91_PIN_PA20, 1); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA1, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA0, 1); + if (data->wire4) { + at91_set_A_periph(AT91_PIN_PA3, 1); + at91_set_A_periph(AT91_PIN_PA4, 1); + at91_set_A_periph(AT91_PIN_PA5, 1); + } + } + + mmc0_data = *data; + at91_clock_associate("mci0_clk", &at91sam9263_mmc1_device.dev, "mci_clk"); + platform_device_register(&at91sam9263_mmc0_device); + } else { /* MCI1 */ + /* CLK */ + at91_set_A_periph(AT91_PIN_PA6, 0); + + if (data->slot_b) { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA21, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA22, 1); + if (data->wire4) { + at91_set_A_periph(AT91_PIN_PA23, 1); + at91_set_A_periph(AT91_PIN_PA24, 1); + at91_set_A_periph(AT91_PIN_PA25, 1); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA7, 1); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA8, 1); + if (data->wire4) { + at91_set_A_periph(AT91_PIN_PA9, 1); + at91_set_A_periph(AT91_PIN_PA10, 1); + at91_set_A_periph(AT91_PIN_PA11, 1); + } + } + + mmc1_data = *data; + at91_clock_associate("mci1_clk", &at91sam9263_mmc1_device.dev, "mci_clk"); + platform_device_register(&at91sam9263_mmc1_device); + } +} +#else +void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +#define NAND_BASE AT91_CHIPSELECT_3 + +static struct resource nand_resources[] = { + { + .start = NAND_BASE, + .end = NAND_BASE + SZ_256M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91sam9263_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = nand_resources, + .num_resources = ARRAY_SIZE(nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + unsigned long csa, mode; + + if (!data) + return; + + csa = at91_sys_read(AT91_MATRIX_EBI0CSA); + at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC); + + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) + | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); + + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + nand_data = *data; + platform_device_register(&at91sam9263_nand_device); +} +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) + +static struct resource twi_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_TWI, + .end = AT91SAM9263_BASE_TWI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_TWI, + .end = AT91SAM9263_ID_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_twi_device = { + .name = "at91_i2c", + .id = -1, + .resource = twi_resources, + .num_resources = ARRAY_SIZE(twi_resources), +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PB4, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PB4, 1); + + at91_set_A_periph(AT91_PIN_PB5, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PB5, 1); + + platform_device_register(&at91sam9263_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource spi0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_SPI0, + .end = AT91SAM9263_BASE_SPI0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_SPI0, + .end = AT91SAM9263_ID_SPI0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_spi0_device = { + .name = "atmel_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi0_resources, + .num_resources = ARRAY_SIZE(spi0_resources), +}; + +static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA5, AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PB11 }; + +static struct resource spi1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_SPI1, + .end = AT91SAM9263_BASE_SPI1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_SPI1, + .end = AT91SAM9263_ID_SPI1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91sam9263_spi1_device = { + .name = "atmel_spi", + .id = 1, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = spi1_resources, + .num_resources = ARRAY_SIZE(spi1_resources), +}; + +static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB15, AT91_PIN_PB16, AT91_PIN_PB17, AT91_PIN_PB18 }; + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + short enable_spi0 = 0; + short enable_spi1 = 0; + + /* Choose SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else if (devices[i].bus_num == 0) + cs_pin = spi0_standard_cs[devices[i].chip_select]; + else + cs_pin = spi1_standard_cs[devices[i].chip_select]; + + if (devices[i].bus_num == 0) + enable_spi0 = 1; + else + enable_spi1 = 1; + + /* enable chip-select pin */ + at91_set_gpio_output(cs_pin, 1); + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + + /* Configure SPI bus(es) */ + if (enable_spi0) { + at91_set_B_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */ + at91_set_B_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */ + at91_set_B_periph(AT91_PIN_PA2, 0); /* SPI1_SPCK */ + + at91_clock_associate("spi0_clk", &at91sam9263_spi0_device.dev, "spi_clk"); + platform_device_register(&at91sam9263_spi0_device); + } + if (enable_spi1) { + at91_set_A_periph(AT91_PIN_PB12, 0); /* SPI1_MISO */ + at91_set_A_periph(AT91_PIN_PB13, 0); /* SPI1_MOSI */ + at91_set_A_periph(AT91_PIN_PB14, 0); /* SPI1_SPCK */ + + at91_clock_associate("spi1_clk", &at91sam9263_spi1_device.dev, "spi_clk"); + platform_device_register(&at91sam9263_spi1_device); + } +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + /* Enable GPIO to access the LEDs */ + at91_set_gpio_output(cpu_led, 1); + at91_set_gpio_output(timer_led, 1); + + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SERIAL_ATMEL) + +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ + .regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU), +}; + +static struct platform_device at91sam9263_dbgu_device = { + .name = "atmel_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_US0, + .end = AT91SAM9263_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_US0, + .end = AT91SAM9263_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9263_uart0_device = { + .name = "atmel_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA26, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PA27, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PA28, 0); /* RTS0 */ + at91_set_A_periph(AT91_PIN_PA29, 0); /* CTS0 */ +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_US1, + .end = AT91SAM9263_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_US1, + .end = AT91SAM9263_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9263_uart1_device = { + .name = "atmel_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */ + at91_set_B_periph(AT91_PIN_PD7, 0); /* RTS1 */ + at91_set_B_periph(AT91_PIN_PD8, 0); /* CTS1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91SAM9263_BASE_US2, + .end = AT91SAM9263_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9263_ID_US2, + .end = AT91SAM9263_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct atmel_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91sam9263_uart2_device = { + .name = "atmel_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */ + at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */ + at91_set_B_periph(AT91_PIN_PD5, 0); /* RTS2 */ + at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */ +} + +struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ +struct platform_device *atmel_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91sam9263_uart0_device; + at91_clock_associate("usart0_clk", &at91sam9263_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91sam9263_uart1_device; + at91_clock_associate("usart1_clk", &at91sam9263_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91sam9263_uart2_device; + at91_clock_associate("usart2_clk", &at91sam9263_uart2_device.dev, "usart"); + break; + case 3: + configure_dbgu_pins(); + at91_uarts[i] = &at91sam9263_dbgu_device; + at91_clock_associate("mck", &at91sam9263_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < ATMEL_MAX_UART) + atmel_default_console_device = at91_uarts[config->console_tty]; + if (!atmel_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < ATMEL_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + return 0; +} + +arch_initcall(at91_add_standard_devices); diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index baab095f6e32..27e7279b5b39 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -598,7 +598,7 @@ int __init at91_clock_init(unsigned long main_clock) udpck.pmc_mask = AT91RM9200_PMC_UDP; at91_sys_write(AT91_PMC_SCDR, AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP); at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); - } else if (cpu_is_at91sam9260()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { uhpck.pmc_mask = AT91SAM926x_PMC_UHP; udpck.pmc_mask = AT91SAM926x_PMC_UDP; at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP); diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index 10ee37bf6d4d..bda26221c522 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -12,11 +12,13 @@ extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks); extern void __init at91sam9260_initialize(unsigned long main_clock); extern void __init at91sam9261_initialize(unsigned long main_clock); +extern void __init at91sam9263_initialize(unsigned long main_clock); /* Interrupts */ extern void __init at91rm9200_init_interrupts(unsigned int priority[]); extern void __init at91sam9260_init_interrupts(unsigned int priority[]); extern void __init at91sam9261_init_interrupts(unsigned int priority[]); +extern void __init at91sam9263_init_interrupts(unsigned int priority[]); extern void __init at91_aic_init(unsigned int priority[]); /* Timer */ diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index e095b1fe8d8a..b49bfda53d7f 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -80,6 +80,8 @@ static int at91_pm_verify_clocks(void) #warning "Check SAM9260 USB clocks" } else if (cpu_is_at91sam9261()) { #warning "Check SAM9261 USB clocks" + } else if (cpu_is_at91sam9263()) { +#warning "Check SAM9263 USB clocks" } #ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index aade2f72c920..b305cbda8b87 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -171,8 +171,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_CACHE_VIVT diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 812c733ba8ce..8afecb8a98ee 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -913,7 +913,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, 0); if (cpu_is_at91rm9200()) at91_set_gpio_value(udc->board.pullup_pin, 1); - else if (cpu_is_at91sam9260()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc |= AT91_UDP_TXVC_PUON; @@ -930,7 +930,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS); if (cpu_is_at91rm9200()) at91_set_gpio_value(udc->board.pullup_pin, 0); - else if (cpu_is_at91sam9260()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc &= ~AT91_UDP_TXVC_PUON; diff --git a/include/asm-arm/arch-at91/at91sam9263.h b/include/asm-arm/arch-at91/at91sam9263.h new file mode 100644 index 000000000000..f4af68ae0ea9 --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam9263.h @@ -0,0 +1,131 @@ +/* + * include/asm-arm/arch-at91/at91sam9263.h + * + * (C) 2007 Atmel Corporation. + * + * Common definitions. + * Based on AT91SAM9263 datasheet revision B (Preliminary). + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM9263_H +#define AT91SAM9263_H + +/* + * Peripheral identifiers/interrupts. + */ +#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ +#define AT91_ID_SYS 1 /* System Peripherals */ +#define AT91SAM9263_ID_PIOA 2 /* Parallel IO Controller A */ +#define AT91SAM9263_ID_PIOB 3 /* Parallel IO Controller B */ +#define AT91SAM9263_ID_PIOCDE 4 /* Parallel IO Controller C, D and E */ +#define AT91SAM9263_ID_US0 7 /* USART 0 */ +#define AT91SAM9263_ID_US1 8 /* USART 1 */ +#define AT91SAM9263_ID_US2 9 /* USART 2 */ +#define AT91SAM9263_ID_MCI0 10 /* Multimedia Card Interface 0 */ +#define AT91SAM9263_ID_MCI1 11 /* Multimedia Card Interface 1 */ +#define AT91SAM9263_ID_CAN 12 /* CAN */ +#define AT91SAM9263_ID_TWI 13 /* Two-Wire Interface */ +#define AT91SAM9263_ID_SPI0 14 /* Serial Peripheral Interface 0 */ +#define AT91SAM9263_ID_SPI1 15 /* Serial Peripheral Interface 1 */ +#define AT91SAM9263_ID_SSC0 16 /* Serial Synchronous Controller 0 */ +#define AT91SAM9263_ID_SSC1 17 /* Serial Synchronous Controller 1 */ +#define AT91SAM9263_ID_AC97C 18 /* AC97 Controller */ +#define AT91SAM9263_ID_TCB 19 /* Timer Counter 0, 1 and 2 */ +#define AT91SAM9263_ID_PWMC 20 /* Pulse Width Modulation Controller */ +#define AT91SAM9263_ID_EMAC 21 /* Ethernet */ +#define AT91SAM9263_ID_2DGE 23 /* 2D Graphic Engine */ +#define AT91SAM9263_ID_UDP 24 /* USB Device Port */ +#define AT91SAM9263_ID_ISI 25 /* Image Sensor Interface */ +#define AT91SAM9263_ID_LCDC 26 /* LCD Controller */ +#define AT91SAM9263_ID_DMA 27 /* DMA Controller */ +#define AT91SAM9263_ID_UHP 29 /* USB Host port */ +#define AT91SAM9263_ID_IRQ0 30 /* Advanced Interrupt Controller (IRQ0) */ +#define AT91SAM9263_ID_IRQ1 31 /* Advanced Interrupt Controller (IRQ1) */ + + +/* + * User Peripheral physical base addresses. + */ +#define AT91SAM9263_BASE_UDP 0xfff78000 +#define AT91SAM9263_BASE_TCB0 0xfff7c000 +#define AT91SAM9263_BASE_TC0 0xfff7c000 +#define AT91SAM9263_BASE_TC1 0xfff7c040 +#define AT91SAM9263_BASE_TC2 0xfff7c080 +#define AT91SAM9263_BASE_MCI0 0xfff80000 +#define AT91SAM9263_BASE_MCI1 0xfff84000 +#define AT91SAM9263_BASE_TWI 0xfff88000 +#define AT91SAM9263_BASE_US0 0xfff8c000 +#define AT91SAM9263_BASE_US1 0xfff90000 +#define AT91SAM9263_BASE_US2 0xfff94000 +#define AT91SAM9263_BASE_SSC0 0xfff98000 +#define AT91SAM9263_BASE_SSC1 0xfff9c000 +#define AT91SAM9263_BASE_AC97C 0xfffa0000 +#define AT91SAM9263_BASE_SPI0 0xfffa4000 +#define AT91SAM9263_BASE_SPI1 0xfffa8000 +#define AT91SAM9263_BASE_CAN 0xfffac000 +#define AT91SAM9263_BASE_PWMC 0xfffb8000 +#define AT91SAM9263_BASE_EMAC 0xfffbc000 +#define AT91SAM9263_BASE_ISI 0xfffc4000 +#define AT91SAM9263_BASE_2DGE 0xfffc8000 +#define AT91_BASE_SYS 0xffffe000 + +/* + * System Peripherals (offset from AT91_BASE_SYS) + */ +#define AT91_ECC0 (0xffffe000 - AT91_BASE_SYS) +#define AT91_SDRAMC0 (0xffffe200 - AT91_BASE_SYS) +#define AT91_SMC0 (0xffffe400 - AT91_BASE_SYS) +#define AT91_ECC1 (0xffffe600 - AT91_BASE_SYS) +#define AT91_SDRAMC1 (0xffffe800 - AT91_BASE_SYS) +#define AT91_SMC1 (0xffffea00 - AT91_BASE_SYS) +#define AT91_MATRIX (0xffffec00 - AT91_BASE_SYS) +#define AT91_CCFG (0xffffed10 - AT91_BASE_SYS) +#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS) +#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) +#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS) +#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS) +#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS) +#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS) +#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS) +#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) +#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) +#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) +#define AT91_RTT0 (0xfffffd20 - AT91_BASE_SYS) +#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) +#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) +#define AT91_RTT1 (0xfffffd50 - AT91_BASE_SYS) +#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS) + +#define AT91_SMC AT91_SMC0 + +/* + * Internal Memory. + */ +#define AT91SAM9263_SRAM0_BASE 0x00300000 /* Internal SRAM 0 base address */ +#define AT91SAM9263_SRAM0_SIZE (80 * SZ_1K) /* Internal SRAM 0 size (80Kb) */ + +#define AT91SAM9263_ROM_BASE 0x00400000 /* Internal ROM base address */ +#define AT91SAM9263_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ + +#define AT91SAM9263_SRAM1_BASE 0x00500000 /* Internal SRAM 1 base address */ +#define AT91SAM9263_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ + +#define AT91SAM9263_LCDC_BASE 0x00700000 /* LCD Controller */ +#define AT91SAM9263_DMAC_BASE 0x00800000 /* DMA Controller */ +#define AT91SAM9263_UHP_BASE 0x00a00000 /* USB Host controller */ + +#if 0 +/* + * PIO pin definitions (peripheral A/B multiplexing). + */ + +// TODO: Add + +#endif + +#endif diff --git a/include/asm-arm/arch-at91/at91sam9263_matrix.h b/include/asm-arm/arch-at91/at91sam9263_matrix.h new file mode 100644 index 000000000000..6fc6e4be624e --- /dev/null +++ b/include/asm-arm/arch-at91/at91sam9263_matrix.h @@ -0,0 +1,129 @@ +/* + * include/asm-arm/arch-at91/at91sam9263_matrix.h + * + * Copyright (C) 2006 Atmel Corporation. + * + * Memory Controllers (MATRIX, EBI) - System peripherals registers. + * Based on AT91SAM9263 datasheet revision B (Preliminary). + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef AT91SAM9263_MATRIX_H +#define AT91SAM9263_MATRIX_H + +#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */ +#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */ +#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */ +#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */ +#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */ +#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */ +#define AT91_MATRIX_MCFG6 (AT91_MATRIX + 0x18) /* Master Configuration Register 6 */ +#define AT91_MATRIX_MCFG7 (AT91_MATRIX + 0x1C) /* Master Configuration Register 7 */ +#define AT91_MATRIX_MCFG8 (AT91_MATRIX + 0x20) /* Master Configuration Register 8 */ +#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ +#define AT91_MATRIX_ULBT_INFINITE (0 << 0) +#define AT91_MATRIX_ULBT_SINGLE (1 << 0) +#define AT91_MATRIX_ULBT_FOUR (2 << 0) +#define AT91_MATRIX_ULBT_EIGHT (3 << 0) +#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) + +#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */ +#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */ +#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */ +#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */ +#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */ +#define AT91_MATRIX_SCFG5 (AT91_MATRIX + 0x54) /* Slave Configuration Register 5 */ +#define AT91_MATRIX_SCFG6 (AT91_MATRIX + 0x58) /* Slave Configuration Register 6 */ +#define AT91_MATRIX_SCFG7 (AT91_MATRIX + 0x5C) /* Slave Configuration Register 7 */ +#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ +#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ +#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) +#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) +#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) +#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ +#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */ +#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24) +#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24) + +#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */ +#define AT91_MATRIX_PRBS0 (AT91_MATRIX + 0x84) /* Priority Register B for Slave 0 */ +#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */ +#define AT91_MATRIX_PRBS1 (AT91_MATRIX + 0x8C) /* Priority Register B for Slave 1 */ +#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */ +#define AT91_MATRIX_PRBS2 (AT91_MATRIX + 0x94) /* Priority Register B for Slave 2 */ +#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */ +#define AT91_MATRIX_PRBS3 (AT91_MATRIX + 0x9C) /* Priority Register B for Slave 3 */ +#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */ +#define AT91_MATRIX_PRBS4 (AT91_MATRIX + 0xA4) /* Priority Register B for Slave 4 */ +#define AT91_MATRIX_PRAS5 (AT91_MATRIX + 0xA8) /* Priority Register A for Slave 5 */ +#define AT91_MATRIX_PRBS5 (AT91_MATRIX + 0xAC) /* Priority Register B for Slave 5 */ +#define AT91_MATRIX_PRAS6 (AT91_MATRIX + 0xB0) /* Priority Register A for Slave 6 */ +#define AT91_MATRIX_PRBS6 (AT91_MATRIX + 0xB4) /* Priority Register B for Slave 6 */ +#define AT91_MATRIX_PRAS7 (AT91_MATRIX + 0xB8) /* Priority Register A for Slave 7 */ +#define AT91_MATRIX_PRBS7 (AT91_MATRIX + 0xBC) /* Priority Register B for Slave 7 */ +#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ +#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ +#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ +#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ +#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ +#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ +#define AT91_MATRIX_M6PR (3 << 24) /* Master 6 Priority */ +#define AT91_MATRIX_M7PR (3 << 28) /* Master 7 Priority */ +#define AT91_MATRIX_M8PR (3 << 0) /* Master 8 Priority (in Register B) */ + +#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */ +#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ +#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ +#define AT91_MATRIX_RCB2 (1 << 2) +#define AT91_MATRIX_RCB3 (1 << 3) +#define AT91_MATRIX_RCB4 (1 << 4) +#define AT91_MATRIX_RCB5 (1 << 5) +#define AT91_MATRIX_RCB6 (1 << 6) +#define AT91_MATRIX_RCB7 (1 << 7) +#define AT91_MATRIX_RCB8 (1 << 8) + +#define AT91_MATRIX_TCMR (AT91_MATRIX + 0x114) /* TCM Configuration Register */ +#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ +#define AT91_MATRIX_ITCM_0 (0 << 0) +#define AT91_MATRIX_ITCM_16 (5 << 0) +#define AT91_MATRIX_ITCM_32 (6 << 0) +#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ +#define AT91_MATRIX_DTCM_0 (0 << 4) +#define AT91_MATRIX_DTCM_16 (5 << 4) +#define AT91_MATRIX_DTCM_32 (6 << 4) + +#define AT91_MATRIX_EBI0CSA (AT91_MATRIX + 0x120) /* EBI0 Chip Select Assignment Register */ +#define AT91_MATRIX_EBI0_CS1A (1 << 1) /* Chip Select 1 Assignment */ +#define AT91_MATRIX_EBI0_CS1A_SMC (0 << 1) +#define AT91_MATRIX_EBI0_CS1A_SDRAMC (1 << 1) +#define AT91_MATRIX_EBI0_CS3A (1 << 3) /* Chip Select 3 Assignment */ +#define AT91_MATRIX_EBI0_CS3A_SMC (0 << 3) +#define AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA (1 << 3) +#define AT91_MATRIX_EBI0_CS4A (1 << 4) /* Chip Select 4 Assignment */ +#define AT91_MATRIX_EBI0_CS4A_SMC (0 << 4) +#define AT91_MATRIX_EBI0_CS4A_SMC_CF1 (1 << 4) +#define AT91_MATRIX_EBI0_CS5A (1 << 5) /* Chip Select 5 Assignment */ +#define AT91_MATRIX_EBI0_CS5A_SMC (0 << 5) +#define AT91_MATRIX_EBI0_CS5A_SMC_CF2 (1 << 5) +#define AT91_MATRIX_EBI0_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ +#define AT91_MATRIX_EBI0_VDDIOMSEL (1 << 16) /* Memory voltage selection */ +#define AT91_MATRIX_EBI0_VDDIOMSEL_1_8V (0 << 16) +#define AT91_MATRIX_EBI0_VDDIOMSEL_3_3V (1 << 16) + +#define AT91_MATRIX_EBI1CSA (AT91_MATRIX + 0x124) /* EBI1 Chip Select Assignment Register */ +#define AT91_MATRIX_EBI1_CS1A (1 << 1) /* Chip Select 1 Assignment */ +#define AT91_MATRIX_EBI1_CS1A_SMC (0 << 1) +#define AT91_MATRIX_EBI1_CS1A_SDRAMC (1 << 1) +#define AT91_MATRIX_EBI1_CS2A (1 << 3) /* Chip Select 3 Assignment */ +#define AT91_MATRIX_EBI1_CS2A_SMC (0 << 3) +#define AT91_MATRIX_EBI1_CS2A_SMC_SMARTMEDIA (1 << 3) +#define AT91_MATRIX_EBI1_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ +#define AT91_MATRIX_EBI1_VDDIOMSEL (1 << 16) /* Memory voltage selection */ +#define AT91_MATRIX_EBI1_VDDIOMSEL_1_8V (0 << 16) +#define AT91_MATRIX_EBI1_VDDIOMSEL_3_3V (1 << 16) + +#endif diff --git a/include/asm-arm/arch-at91/at91sam926x_mc.h b/include/asm-arm/arch-at91/at91sam926x_mc.h index 355eee67ebca..d82631c251f1 100644 --- a/include/asm-arm/arch-at91/at91sam926x_mc.h +++ b/include/asm-arm/arch-at91/at91sam926x_mc.h @@ -131,4 +131,11 @@ #define AT91_SMC_PS_16 (2 << 28) #define AT91_SMC_PS_32 (3 << 28) +#if defined(AT91_SMC1) /* The AT91SAM9263 has 2 Static Memory contollers */ +#define AT91_SMC1_SETUP(n) (AT91_SMC1 + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ +#define AT91_SMC1_PULSE(n) (AT91_SMC1 + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ +#define AT91_SMC1_CYCLE(n) (AT91_SMC1 + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ +#define AT91_SMC1_MODE(n) (AT91_SMC1 + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ +#endif + #endif diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h index 762eb41aa675..9efde0dad249 100644 --- a/include/asm-arm/arch-at91/cpu.h +++ b/include/asm-arm/arch-at91/cpu.h @@ -20,6 +20,7 @@ #define ARCH_ID_AT91RM9200 0x09290780 #define ARCH_ID_AT91SAM9260 0x019803a0 #define ARCH_ID_AT91SAM9261 0x019703a0 +#define ARCH_ID_AT91SAM9263 0x019607a0 static inline unsigned long at91_cpu_identify(void) @@ -46,4 +47,10 @@ static inline unsigned long at91_cpu_identify(void) #define cpu_is_at91sam9261() (0) #endif +#ifdef CONFIG_ARCH_AT91SAM9263 +#define cpu_is_at91sam9263() (at91_cpu_identify() == ARCH_ID_AT91SAM9263) +#else +#define cpu_is_at91sam9263() (0) +#endif + #endif diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h index 1637fc4a0d8f..eaaf1c12b753 100644 --- a/include/asm-arm/arch-at91/hardware.h +++ b/include/asm-arm/arch-at91/hardware.h @@ -22,6 +22,8 @@ #include #elif defined(CONFIG_ARCH_AT91SAM9261) #include +#elif defined(CONFIG_ARCH_AT91SAM9263) +#include #else #error "Unsupported AT91 processor" #endif diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h index b24e364997e1..f41636d607a2 100644 --- a/include/asm-arm/arch-at91/timex.h +++ b/include/asm-arm/arch-at91/timex.h @@ -32,6 +32,11 @@ #define AT91SAM9_MASTER_CLOCK 99300000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) +#elif defined(CONFIG_ARCH_AT91SAM9263) + +#define AT91SAM9_MASTER_CLOCK 99959500 +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + #endif #endif -- cgit v1.2.3 From e6d92e6397634ac7d2e80b16c52f0dfab9b673b4 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 10:22:16 +0100 Subject: [ARM] 4146/1: AT91: Support for AT91SAM9263-EK board. Add support for the Atmel AT91SAM9263-EK board. Original patch from Nicolas Ferre. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/configs/at91sam9263ek_defconfig | 1184 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/Kconfig | 19 +- arch/arm/mach-at91/Makefile | 3 + arch/arm/mach-at91/board-sam9263ek.c | 176 +++++ 4 files changed, 1380 insertions(+), 2 deletions(-) create mode 100644 arch/arm/configs/at91sam9263ek_defconfig create mode 100644 arch/arm/mach-at91/board-sam9263ek.c (limited to 'arch') diff --git a/arch/arm/configs/at91sam9263ek_defconfig b/arch/arm/configs/at91sam9263ek_defconfig new file mode 100644 index 000000000000..c72ab82873d5 --- /dev/null +++ b/arch/arm/configs/at91sam9263ek_defconfig @@ -0,0 +1,1184 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.20-rc1 +# Mon Jan 8 16:06:54 2007 +# +CONFIG_ARM=y +# CONFIG_GENERIC_TIME is not set +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +CONFIG_ARCH_AT91=y +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +# CONFIG_ARCH_AT91SAM9260 is not set +# CONFIG_ARCH_AT91SAM9261 is not set +CONFIG_ARCH_AT91SAM9263=y + +# +# AT91SAM9263 Board Type +# +CONFIG_MACH_AT91SAM9263EK=y + +# +# AT91 Board Options +# +CONFIG_MTD_AT91_DATAFLASH_CARD=y +# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set + +# +# AT91 Feature Selections +# +# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set + +# +# Bus support +# + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set +# CONFIG_APM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_DIAG is not set +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_OBSOLETE_CHIPS is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=y +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set + +# +# NAND Flash Device Drivers +# +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_AT91=y +# CONFIG_MTD_NAND_NANDSIM is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_DEBUG is not set + +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_TSDEV=y +CONFIG_INPUT_TSDEV_SCREEN_X=240 +CONFIG_INPUT_TSDEV_SCREEN_Y=320 +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_UCB1400 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +CONFIG_I2C_AT91=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# SPI support +# +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# +# Misc devices +# +# CONFIG_TIFM_CORE is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_FIRMWARE_EDID is not set +CONFIG_FB=y +# CONFIG_FB_CFB_FILLRECT is not set +# CONFIG_FB_CFB_COPYAREA is not set +# CONFIG_FB_CFB_IMAGEBLIT is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set + +# +# Logo configuration +# +# CONFIG_LOGO is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# HID Devices +# +CONFIG_HID=y + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_MULTITHREAD_PROBE is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_TOUCHSCREEN is not set +# CONFIG_USB_YEALINK is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_ATI_REMOTE2 is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET_MII is not set +# CONFIG_USB_USBNET is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=m +# CONFIG_USB_ETH is not set +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set + +# +# MMC/SD Card support +# +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +CONFIG_MMC_BLOCK=y +CONFIG_MMC_AT91=m +# CONFIG_MMC_TIFM_SD is not set + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +# CONFIG_NFS_V3 is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set + +# +# Distributed Lock Manager +# +# CONFIG_DLM is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_RWSEMS is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_IOMAP_COPY=y diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 2499385e22da..9313888d77c9 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -121,17 +121,32 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9263 + +comment "AT91SAM9263 Board Type" + +config MACH_AT91SAM9263EK + bool "Atmel AT91SAM9263-EK Evaluation Kit" + depends on ARCH_AT91SAM9263 + help + Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. + + +endif + +# ---------------------------------------------------------- + comment "AT91 Board Options" config MTD_AT91_DATAFLASH_CARD bool "Enable DataFlash Card support" - depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK) + depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK) help Enable support for the DataFlash card. config MTD_NAND_AT91_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 2fd4cd4a57f8..05de6cdc88f1 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -32,6 +32,9 @@ obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o # AT91SAM9261 board-specific support obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o +# AT91SAM9263 board-specific support +obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o + # LEDs support led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o led-$(CONFIG_MACH_AT91RM9200EK) += leds.o diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c new file mode 100644 index 000000000000..8fdce11a880c --- /dev/null +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -0,0 +1,176 @@ +/* + * linux/arch/arm/mach-at91/board-sam9263ek.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2007 Atmel Corporation. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 2 = USART0 .. USART2 + * 3 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 16.367 MHz crystal */ + at91sam9263_initialize(16367660); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91sam9263_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, + .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 }, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PA25, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +}; + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .wire4 = 1, + .det_pin = AT91_PIN_PE18, + .wp_pin = AT91_PIN_PE19, +// .vcc_pin = ... not connected +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = 64 * 1024 * 1024, + }, + { + .name = "Partition 2", + .offset = 64 * 1024 * 1024, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PA22, + .enable_pin = AT91_PIN_PD15, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* MMC */ + at91_add_device_mmc(1, &ek_mmc_data); + /* NAND */ + at91_add_device_nand(&ek_nand_data); +} + +MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END -- cgit v1.2.3 From c177a1e75a07237efe1f68fbf430892fdf2bb868 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 10:25:38 +0100 Subject: [ARM] 4147/1: AT91: Define Timer/Counter clocks. Define the Timer/Counter Unit clocks on the AT91RM9200, AT91SAM9260 and AT91SAM9261 processors. Original patch from David Brownell. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/at91rm9200.c | 37 ++++++++++++++++++++++++++++++++++++- arch/arm/mach-at91/at91sam9260.c | 38 ++++++++++++++++++++++++++++++++++++-- arch/arm/mach-at91/at91sam9261.c | 19 ++++++++++++++++++- 3 files changed, 90 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c index 870d4a4eb806..2ddcdd69df7d 100644 --- a/arch/arm/mach-at91/at91rm9200.c +++ b/arch/arm/mach-at91/at91rm9200.c @@ -117,6 +117,36 @@ static struct clk pioD_clk = { .pmc_mask = 1 << AT91RM9200_ID_PIOD, .type = CLK_TYPE_PERIPHERAL, }; +static struct clk tc0_clk = { + .name = "tc0_clk", + .pmc_mask = 1 << AT91RM9200_ID_TC0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc1_clk = { + .name = "tc1_clk", + .pmc_mask = 1 << AT91RM9200_ID_TC1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc2_clk = { + .name = "tc2_clk", + .pmc_mask = 1 << AT91RM9200_ID_TC2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc3_clk = { + .name = "tc3_clk", + .pmc_mask = 1 << AT91RM9200_ID_TC3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc4_clk = { + .name = "tc4_clk", + .pmc_mask = 1 << AT91RM9200_ID_TC4, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc5_clk = { + .name = "tc5_clk", + .pmc_mask = 1 << AT91RM9200_ID_TC5, + .type = CLK_TYPE_PERIPHERAL, +}; static struct clk *periph_clocks[] __initdata = { &pioA_clk, @@ -132,7 +162,12 @@ static struct clk *periph_clocks[] __initdata = { &twi_clk, &spi_clk, // ssc 0 .. ssc2 - // tc0 .. tc5 + &tc0_clk, + &tc1_clk, + &tc2_clk, + &tc3_clk, + &tc4_clk, + &tc5_clk, &ohci_clk, ðer_clk, // irq0 .. irq6 diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index ffc4c0944740..e03ee625f40c 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -107,6 +107,21 @@ static struct clk spi1_clk = { .pmc_mask = 1 << AT91SAM9260_ID_SPI1, .type = CLK_TYPE_PERIPHERAL, }; +static struct clk tc0_clk = { + .name = "tc0_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TC0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc1_clk = { + .name = "tc1_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TC1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc2_clk = { + .name = "tc2_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TC2, + .type = CLK_TYPE_PERIPHERAL, +}; static struct clk ohci_clk = { .name = "ohci_clk", .pmc_mask = 1 << AT91SAM9260_ID_UHP, @@ -137,6 +152,21 @@ static struct clk usart5_clk = { .pmc_mask = 1 << AT91SAM9260_ID_US5, .type = CLK_TYPE_PERIPHERAL, }; +static struct clk tc3_clk = { + .name = "tc3_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TC3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc4_clk = { + .name = "tc4_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TC4, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc5_clk = { + .name = "tc5_clk", + .pmc_mask = 1 << AT91SAM9260_ID_TC5, + .type = CLK_TYPE_PERIPHERAL, +}; static struct clk *periph_clocks[] __initdata = { &pioA_clk, @@ -152,14 +182,18 @@ static struct clk *periph_clocks[] __initdata = { &spi0_clk, &spi1_clk, // ssc - // tc0 .. tc2 + &tc0_clk, + &tc1_clk, + &tc2_clk, &ohci_clk, ðer_clk, &isi_clk, &usart3_clk, &usart4_clk, &usart5_clk, - // tc3 .. tc5 + &tc3_clk, + &tc4_clk, + &tc5_clk, // irq0 .. irq2 }; diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 47e02ff7e872..1a9102368f11 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -97,6 +97,21 @@ static struct clk spi1_clk = { .pmc_mask = 1 << AT91SAM9261_ID_SPI1, .type = CLK_TYPE_PERIPHERAL, }; +static struct clk tc0_clk = { + .name = "tc0_clk", + .pmc_mask = 1 << AT91SAM9261_ID_TC0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc1_clk = { + .name = "tc1_clk", + .pmc_mask = 1 << AT91SAM9261_ID_TC1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk tc2_clk = { + .name = "tc2_clk", + .pmc_mask = 1 << AT91SAM9261_ID_TC2, + .type = CLK_TYPE_PERIPHERAL, +}; static struct clk ohci_clk = { .name = "ohci_clk", .pmc_mask = 1 << AT91SAM9261_ID_UHP, @@ -121,7 +136,9 @@ static struct clk *periph_clocks[] __initdata = { &spi0_clk, &spi1_clk, // ssc 0 .. ssc2 - // tc0 .. tc2 + &tc0_clk, + &tc1_clk, + &tc2_clk, &ohci_clk, &lcdc_clk, // irq0 .. irq2 -- cgit v1.2.3 From 127a7ec69c9ce17a5add2e3c8c2f1a2733fb88d8 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 10:44:46 +0100 Subject: [ARM] 4148/1: AT91: Physically mapped flash on CSB337 and CSB637 boards. Define the physically mapped flash on the Cogent CSB337 and CSB637 boards. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/configs/csb337_defconfig | 6 ++++-- arch/arm/configs/csb637_defconfig | 6 ++++-- arch/arm/mach-at91/board-csb337.c | 39 +++++++++++++++++++++++++++++++++++++++ arch/arm/mach-at91/board-csb637.c | 39 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 86 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/configs/csb337_defconfig b/arch/arm/configs/csb337_defconfig index 2cadd51506bb..8e55f55333be 100644 --- a/arch/arm/configs/csb337_defconfig +++ b/arch/arm/configs/csb337_defconfig @@ -355,10 +355,12 @@ CONFIG_MTD_CFI_UTIL=y # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0 +CONFIG_MTD_PHYSMAP_LEN=0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=0 # CONFIG_MTD_ARM_INTEGRATOR is not set # CONFIG_MTD_PLATRAM is not set -CONFIG_MTD_CSB337=y # # Self-contained MTD device drivers diff --git a/arch/arm/configs/csb637_defconfig b/arch/arm/configs/csb637_defconfig index 94908c1df4cf..669f035896f9 100644 --- a/arch/arm/configs/csb637_defconfig +++ b/arch/arm/configs/csb637_defconfig @@ -355,10 +355,12 @@ CONFIG_MTD_CFI_UTIL=y # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0 +CONFIG_MTD_PHYSMAP_LEN=0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=0 # CONFIG_MTD_ARM_INTEGRATOR is not set # CONFIG_MTD_PLATRAM is not set -CONFIG_MTD_CSB637=y # # Self-contained MTD device drivers diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index 871c6609d6ec..e18a41e61f0c 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -24,6 +24,7 @@ #include #include #include +#include #include #include @@ -112,6 +113,42 @@ static struct spi_board_info csb337_spi_devices[] = { }, }; +#define CSB_FLASH_BASE AT91_CHIPSELECT_0 +#define CSB_FLASH_SIZE 0x800000 + +static struct mtd_partition csb_flash_partitions[] = { + { + .name = "uMON flash", + .offset = 0, + .size = MTDPART_SIZ_FULL, + .mask_flags = MTD_WRITEABLE, /* read only */ + } +}; + +static struct physmap_flash_data csb_flash_data = { + .width = 2, + .parts = csb_flash_partitions, + .nr_parts = ARRAY_SIZE(csb_flash_partitions), +}; + +static struct resource csb_flash_resources[] = { + { + .start = CSB_FLASH_BASE, + .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device csb_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &csb_flash_data, + }, + .resource = csb_flash_resources, + .num_resources = ARRAY_SIZE(csb_flash_resources), +}; + static void __init csb337_board_init(void) { /* Serial */ @@ -131,6 +168,8 @@ static void __init csb337_board_init(void) at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); /* MMC */ at91_add_device_mmc(0, &csb337_mmc_data); + /* NOR flash */ + platform_device_register(&csb_flash); } MACHINE_START(CSB337, "Cogent CSB337") diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index 774609479c74..77f04b935b3a 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -23,6 +23,7 @@ #include #include #include +#include #include #include @@ -81,6 +82,42 @@ static struct at91_udc_data __initdata csb637_udc_data = { .pullup_pin = AT91_PIN_PB1, }; +#define CSB_FLASH_BASE AT91_CHIPSELECT_0 +#define CSB_FLASH_SIZE 0x1000000 + +static struct mtd_partition csb_flash_partitions[] = { + { + .name = "uMON flash", + .offset = 0, + .size = MTDPART_SIZ_FULL, + .mask_flags = MTD_WRITEABLE, /* read only */ + } +}; + +static struct physmap_flash_data csb_flash_data = { + .width = 2, + .parts = csb_flash_partitions, + .nr_parts = ARRAY_SIZE(csb_flash_partitions), +}; + +static struct resource csb_flash_resources[] = { + { + .start = CSB_FLASH_BASE, + .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device csb_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &csb_flash_data, + }, + .resource = csb_flash_resources, + .num_resources = ARRAY_SIZE(csb_flash_resources), +}; + static void __init csb637_board_init(void) { /* Serial */ @@ -95,6 +132,8 @@ static void __init csb637_board_init(void) at91_add_device_i2c(); /* SPI */ at91_add_device_spi(NULL, 0); + /* NOR flash */ + platform_device_register(&csb_flash); } MACHINE_START(CSB637, "Cogent CSB637") -- cgit v1.2.3 From 3392b309dbd1f1f37454c412c2045448300cf374 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 11:04:19 +0100 Subject: [ARM] 4149/1: AT91: Overrun in SAM9 gettimeoffset(). Fix an overrun in the AT91SAM9 gettimeoffset() function. This causes the time value returned by gettimeofday() to jump "backwards". Original patch from Michel Benoit. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/at91sam926x_time.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c index 59cbbe1e8161..a4dded27fa16 100644 --- a/arch/arm/mach-at91/at91sam926x_time.c +++ b/arch/arm/mach-at91/at91sam926x_time.c @@ -30,7 +30,6 @@ * Returns number of microseconds since last timer interrupt. Note that interrupts * will have been disabled by do_gettimeofday() * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. - * 'tick' is usecs per jiffy (linux/timex.h). */ static unsigned long at91sam926x_gettimeoffset(void) { @@ -39,7 +38,7 @@ static unsigned long at91sam926x_gettimeoffset(void) elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t); /* hardware clock cycles */ - return (unsigned long)(elapsed * 1000000) / LATCH; + return (unsigned long)(elapsed * jiffies_to_usecs(1)) / LATCH; } /* -- cgit v1.2.3 From da11d02c1da201840b94147d3366a32b41b151e1 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 11:18:14 +0100 Subject: [ARM] 4150/1: AT91: LED update The GPIO pin setup should be handed by the platform-setup code, and not directly by the driver. Original patch from David Brownell. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/at91rm9200_devices.c | 4 ++++ arch/arm/mach-at91/at91sam9260_devices.c | 4 ++++ arch/arm/mach-at91/at91sam9261_devices.c | 4 ++++ arch/arm/mach-at91/leds.c | 4 ---- 4 files changed, 12 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 077c81f9bc56..2624a4f22d61 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -594,6 +594,10 @@ u8 at91_leds_timer; void __init at91_init_leds(u8 cpu_led, u8 timer_led) { + /* Enable GPIO to access the LEDs */ + at91_set_gpio_output(cpu_led, 1); + at91_set_gpio_output(timer_led, 1); + at91_leds_cpu = cpu_led; at91_leds_timer = timer_led; } diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index b5d8968e29a7..f7d342ccbebf 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -515,6 +515,10 @@ u8 at91_leds_timer; void __init at91_init_leds(u8 cpu_led, u8 timer_led) { + /* Enable GPIO to access the LEDs */ + at91_set_gpio_output(cpu_led, 1); + at91_set_gpio_output(timer_led, 1); + at91_leds_cpu = cpu_led; at91_leds_timer = timer_led; } diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index b2f6d33d0f8c..e1504766fd64 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -513,6 +513,10 @@ u8 at91_leds_timer; void __init at91_init_leds(u8 cpu_led, u8 timer_led) { + /* Enable GPIO to access the LEDs */ + at91_set_gpio_output(cpu_led, 1); + at91_set_gpio_output(timer_led, 1); + at91_leds_cpu = cpu_led; at91_leds_timer = timer_led; } diff --git a/arch/arm/mach-at91/leds.c b/arch/arm/mach-at91/leds.c index 1a333730466e..0d5144973988 100644 --- a/arch/arm/mach-at91/leds.c +++ b/arch/arm/mach-at91/leds.c @@ -86,10 +86,6 @@ static int __init leds_init(void) if (!at91_leds_timer || !at91_leds_cpu) return -ENODEV; - /* Enable PIO to access the LEDs */ - at91_set_gpio_output(at91_leds_timer, 1); - at91_set_gpio_output(at91_leds_cpu, 1); - leds_event = at91_leds_event; leds_event(led_start); -- cgit v1.2.3 From 271f5ca638b322248c6bb0a797284886f39ccce6 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Thu, 8 Feb 2007 01:01:41 +0100 Subject: [ARM] 4142/1: ep93xx: handle IRQT_NOEDGE Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mach-ep93xx/core.c | 25 ++++++++++++++++--------- 1 file changed, 16 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c index 94bba0b87e36..829aed696d98 100644 --- a/arch/arm/mach-ep93xx/core.c +++ b/arch/arm/mach-ep93xx/core.c @@ -152,7 +152,8 @@ struct sys_timer ep93xx_timer = { /************************************************************************* * GPIO handling for EP93xx *************************************************************************/ -static unsigned char gpio_int_enable[3]; +static unsigned char gpio_int_unmasked[3]; +static unsigned char gpio_int_enabled[3]; static unsigned char gpio_int_type1[3]; static unsigned char gpio_int_type2[3]; @@ -162,17 +163,17 @@ static void update_gpio_int_params(int abf) __raw_writeb(0, EP93XX_GPIO_A_INT_ENABLE); __raw_writeb(gpio_int_type2[0], EP93XX_GPIO_A_INT_TYPE2); __raw_writeb(gpio_int_type1[0], EP93XX_GPIO_A_INT_TYPE1); - __raw_writeb(gpio_int_enable[0], EP93XX_GPIO_A_INT_ENABLE); + __raw_writeb(gpio_int_unmasked[0] & gpio_int_enabled[0], EP93XX_GPIO_A_INT_ENABLE); } else if (abf == 1) { __raw_writeb(0, EP93XX_GPIO_B_INT_ENABLE); __raw_writeb(gpio_int_type2[1], EP93XX_GPIO_B_INT_TYPE2); __raw_writeb(gpio_int_type1[1], EP93XX_GPIO_B_INT_TYPE1); - __raw_writeb(gpio_int_enable[1], EP93XX_GPIO_B_INT_ENABLE); + __raw_writeb(gpio_int_unmasked[1] & gpio_int_enabled[1], EP93XX_GPIO_B_INT_ENABLE); } else if (abf == 2) { __raw_writeb(0, EP93XX_GPIO_F_INT_ENABLE); __raw_writeb(gpio_int_type2[2], EP93XX_GPIO_F_INT_TYPE2); __raw_writeb(gpio_int_type1[2], EP93XX_GPIO_F_INT_TYPE1); - __raw_writeb(gpio_int_enable[2], EP93XX_GPIO_F_INT_ENABLE); + __raw_writeb(gpio_int_unmasked[2] & gpio_int_enabled[2], EP93XX_GPIO_F_INT_ENABLE); } else { BUG(); } @@ -200,11 +201,11 @@ void gpio_line_config(int line, int direction) if (direction == GPIO_OUT) { if (line >= 0 && line < 16) { /* Port A/B. */ - gpio_int_enable[line >> 3] &= ~(1 << (line & 7)); + gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7)); update_gpio_int_params(line >> 3); } else if (line >= 40 && line < 48) { /* Port F. */ - gpio_int_enable[2] &= ~(1 << (line & 7)); + gpio_int_unmasked[2] &= ~(1 << (line & 7)); update_gpio_int_params(2); } @@ -290,7 +291,7 @@ static void ep93xx_gpio_irq_mask_ack(unsigned int irq) int line = irq - IRQ_EP93XX_GPIO(0); int port = line >> 3; - gpio_int_enable[port] &= ~(1 << (line & 7)); + gpio_int_unmasked[port] &= ~(1 << (line & 7)); update_gpio_int_params(port); if (port == 0) { @@ -307,7 +308,7 @@ static void ep93xx_gpio_irq_mask(unsigned int irq) int line = irq - IRQ_EP93XX_GPIO(0); int port = line >> 3; - gpio_int_enable[port] &= ~(1 << (line & 7)); + gpio_int_unmasked[port] &= ~(1 << (line & 7)); update_gpio_int_params(port); } @@ -316,7 +317,7 @@ static void ep93xx_gpio_irq_unmask(unsigned int irq) int line = irq - IRQ_EP93XX_GPIO(0); int port = line >> 3; - gpio_int_enable[port] |= 1 << (line & 7); + gpio_int_unmasked[port] |= 1 << (line & 7); update_gpio_int_params(port); } @@ -342,17 +343,23 @@ static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type) line &= 7; if (type & IRQT_RISING) { + gpio_int_enabled[port] |= 1 << line; gpio_int_type1[port] |= 1 << line; gpio_int_type2[port] |= 1 << line; } else if (type & IRQT_FALLING) { + gpio_int_enabled[port] |= 1 << line; gpio_int_type1[port] |= 1 << line; gpio_int_type2[port] &= ~(1 << line); } else if (type & IRQT_HIGH) { + gpio_int_enabled[port] |= 1 << line; gpio_int_type1[port] &= ~(1 << line); gpio_int_type2[port] |= 1 << line; } else if (type & IRQT_LOW) { + gpio_int_enabled[port] |= 1 << line; gpio_int_type1[port] &= ~(1 << line); gpio_int_type2[port] &= ~(1 << line); + } else { + gpio_int_enabled[port] &= ~(1 << line); } update_gpio_int_params(port); -- cgit v1.2.3 From 3e1a80f11f89f318e892694b501735abb51ef626 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Thu, 8 Feb 2007 16:26:23 +0100 Subject: [ARM] 4153/1: fix consistent_sync() off-by-one BUG check In consistent_sync(), start + size can end up pointing one byte beyond the end of the direct RAM mapping. We shouldn't BUG() when this happens. Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mm/consistent.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mm/consistent.c b/arch/arm/mm/consistent.c index 166aee13c4b1..1f9f94f9af4b 100644 --- a/arch/arm/mm/consistent.c +++ b/arch/arm/mm/consistent.c @@ -485,7 +485,7 @@ void consistent_sync(const void *start, size_t size, int direction) { const void *end = start + size; - BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(end)); + BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(end - 1)); switch (direction) { case DMA_FROM_DEVICE: /* invalidate only */ -- cgit v1.2.3 From f2131d348f0bd252801f641018a90d59c987ce48 Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 8 Feb 2007 20:46:20 +0000 Subject: [ARM] Always mark ARMv6 PTWs outer cacheable Other platforms other than SMP may have an outer cache. For these, we also need to mark the page table walks outer cacheable. Since marking the walks always outer cacheable apparantly has no side effects, we might as well always mark them so. However, we continue to only mark PTWs shared if we have SMP enabled. Signed-off-by: Russell King --- arch/arm/mm/proc-v6.S | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S index 7b1843befb9c..d78c0ae7c2c2 100644 --- a/arch/arm/mm/proc-v6.S +++ b/arch/arm/mm/proc-v6.S @@ -30,6 +30,12 @@ #define TTB_RGN_WT (2 << 3) #define TTB_RGN_WB (3 << 3) +#ifndef CONFIG_SMP +#define TTB_FLAGS TTB_RGN_WBWA +#else +#define TTB_FLAGS TTB_RGN_WBWA|TTB_S +#endif + ENTRY(cpu_v6_proc_init) mov pc, lr @@ -92,9 +98,7 @@ ENTRY(cpu_v6_switch_mm) #ifdef CONFIG_MMU mov r2, #0 ldr r1, [r1, #MM_CONTEXT_ID] @ get mm->context.id -#ifdef CONFIG_SMP - orr r0, r0, #TTB_RGN_WBWA|TTB_S @ mark PTWs shared, outer cacheable -#endif + orr r0, r0, #TTB_FLAGS mcr p15, 0, r2, c7, c5, 6 @ flush BTAC/BTB mcr p15, 0, r2, c7, c10, 4 @ drain write buffer mcr p15, 0, r0, c2, c0, 0 @ set TTB 0 @@ -204,9 +208,7 @@ __v6_setup: #ifdef CONFIG_MMU mcr p15, 0, r0, c8, c7, 0 @ invalidate I + D TLBs mcr p15, 0, r0, c2, c0, 2 @ TTB control register -#ifdef CONFIG_SMP - orr r4, r4, #TTB_RGN_WBWA|TTB_S @ mark PTWs shared, outer cacheable -#endif + orr r4, r4, #TTB_FLAGS mcr p15, 0, r4, c2, c0, 1 @ load TTB1 #endif /* CONFIG_MMU */ adr r5, v6_crval -- cgit v1.2.3 From c9b75d132261096ac1170354b9e27837af76a512 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 8 Feb 2007 17:36:34 +0100 Subject: [ARM] 4154/1: AT91: Clock update Unconditionally disabling the PCKs (Programmable Clocks) is not a good idea as it breaks boards that depend on those clocks being enabled by bootloaders. Therefore only disable unused clocks late in the init process, giving the board init code the chance to claim the clock. Patch from Steven Scholz. Since the HCK clocks on SAM9261 are already being registered as a independent clocks, we don't need the special case for HCK0 on the SAM9261. Platform-init code and drivers should use the clock API to enable/disable the clock. Patch from Nicolas Ferre. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/clock.c | 62 ++++++++++++++++++++++------------------------ 1 file changed, 29 insertions(+), 33 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index 27e7279b5b39..f6cb74806043 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -525,27 +525,6 @@ fail: return 0; } -/* - * Several unused clocks may be active. Turn them off. - */ -static void __init at91_periphclk_reset(void) -{ - unsigned long reg; - struct clk *clk; - - reg = at91_sys_read(AT91_PMC_PCSR); - - list_for_each_entry(clk, &clocks, node) { - if (clk->mode != pmc_periph_mode) - continue; - - if (clk->users > 0) - reg &= ~clk->pmc_mask; - } - - at91_sys_write(AT91_PMC_PCDR, reg); -} - static struct clk *const standard_pmc_clocks[] __initdata = { /* four primary clocks */ &clk32k, @@ -586,7 +565,7 @@ int __init at91_clock_init(unsigned long main_clock) pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); /* - * USB clock init: choose 48 MHz PLLB value, turn all clocks off, + * USB clock init: choose 48 MHz PLLB value, * disable 48MHz clock during usb peripheral suspend. * * REVISIT: assumes MCK doesn't derive from PLLB! @@ -596,16 +575,10 @@ int __init at91_clock_init(unsigned long main_clock) if (cpu_is_at91rm9200()) { uhpck.pmc_mask = AT91RM9200_PMC_UHP; udpck.pmc_mask = AT91RM9200_PMC_UDP; - at91_sys_write(AT91_PMC_SCDR, AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP); at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { uhpck.pmc_mask = AT91SAM926x_PMC_UHP; udpck.pmc_mask = AT91SAM926x_PMC_UDP; - at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP); - } else if (cpu_is_at91sam9261()) { - uhpck.pmc_mask = (AT91SAM926x_PMC_UHP | AT91_PMC_HCK0); - udpck.pmc_mask = AT91SAM926x_PMC_UDP; - at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91_PMC_HCK0 | AT91SAM926x_PMC_UDP); } at91_sys_write(AT91_CKGR_PLLBR, 0); @@ -634,11 +607,34 @@ int __init at91_clock_init(unsigned long main_clock) (unsigned) main_clock / 1000000, ((unsigned) main_clock % 1000000) / 1000); - /* disable all programmable clocks */ - at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK0 | AT91_PMC_PCK1 | AT91_PMC_PCK2 | AT91_PMC_PCK3); + return 0; +} + +/* + * Several unused clocks may be active. Turn them off. + */ +static int __init at91_clock_reset(void) +{ + unsigned long pcdr = 0; + unsigned long scdr = 0; + struct clk *clk; + + list_for_each_entry(clk, &clocks, node) { + if (clk->users > 0) + continue; + + if (clk->mode == pmc_periph_mode) + pcdr |= clk->pmc_mask; + + if (clk->mode == pmc_sys_mode) + scdr |= clk->pmc_mask; + + pr_debug("Clocks: disable unused %s\n", clk->name); + } - /* disable all other unused peripheral clocks */ - at91_periphclk_reset(); + at91_sys_write(AT91_PMC_PCDR, pcdr); + at91_sys_write(AT91_PMC_SCDR, scdr); return 0; } +late_initcall(at91_clock_reset); -- cgit v1.2.3 From eeea82ff4a3aebed9f501f04ca7b65d3605f247a Mon Sep 17 00:00:00 2001 From: Ahmed S. Darwish Date: Mon, 5 Feb 2007 16:10:25 -0800 Subject: [ARM] Use ARRAY_SIZE macro when appropriate Use ARRAY_SIZE macro already defined in linux/kernel.h Signed-off-by: Ahmed S. Darwish Signed-off-by: Andrew Morton Signed-off-by: Russell King --- arch/arm/kernel/ecard.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c index 71257e3d513f..f1c0fb974177 100644 --- a/arch/arm/kernel/ecard.c +++ b/arch/arm/kernel/ecard.c @@ -1009,7 +1009,7 @@ ecard_probe(int slot, card_type_t type) ec->fiqmask = 4; } - for (i = 0; i < sizeof(blacklist) / sizeof(*blacklist); i++) + for (i = 0; i < ARRAY_SIZE(blacklist); i++) if (blacklist[i].manufacturer == ec->cid.manufacturer && blacklist[i].product == ec->cid.product) { ec->card_desc = blacklist[i].type; -- cgit v1.2.3 From 382266ad5ad4119ec12df889afa5062a0a0cd6ae Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 5 Feb 2007 14:48:19 +0100 Subject: [ARM] 4135/1: Add support for the L210/L220 cache controllers This patch adds the support for the L210/L220 (outer) cache controller. The cache range operations are done by index/way since L2 cache controller only accepts physical addresses. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mm/Kconfig | 4 ++ arch/arm/mm/Makefile | 2 + arch/arm/mm/cache-l2x0.c | 104 ++++++++++++++++++++++++++++++++++ include/asm-arm/hardware/cache-l2x0.h | 56 ++++++++++++++++++ 4 files changed, 166 insertions(+) create mode 100644 arch/arm/mm/cache-l2x0.c create mode 100644 include/asm-arm/hardware/cache-l2x0.h (limited to 'arch') diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index a84eed9f8542..af3fa9d622ff 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -612,3 +612,7 @@ config NEEDS_SYSCALL_FOR_CMPXCHG config OUTER_CACHE bool default n + +config CACHE_L2X0 + bool + select OUTER_CACHE diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile index d2f5672ecf62..2f8b95947774 100644 --- a/arch/arm/mm/Makefile +++ b/arch/arm/mm/Makefile @@ -66,3 +66,5 @@ obj-$(CONFIG_CPU_SA1100) += proc-sa1100.o obj-$(CONFIG_CPU_XSCALE) += proc-xscale.o obj-$(CONFIG_CPU_XSC3) += proc-xsc3.o obj-$(CONFIG_CPU_V6) += proc-v6.o + +obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c new file mode 100644 index 000000000000..08a36f1b35d2 --- /dev/null +++ b/arch/arm/mm/cache-l2x0.c @@ -0,0 +1,104 @@ +/* + * arch/arm/mm/cache-l2x0.c - L210/L220 cache controller support + * + * Copyright (C) 2007 ARM Limited + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include + +#include +#include +#include + +#define CACHE_LINE_SIZE 32 + +static void __iomem *l2x0_base; + +static inline void sync_writel(unsigned long val, unsigned long reg, + unsigned long complete_mask) +{ + writel(val, l2x0_base + reg); + /* wait for the operation to complete */ + while (readl(l2x0_base + reg) & complete_mask) + ; +} + +static inline void cache_sync(void) +{ + sync_writel(0, L2X0_CACHE_SYNC, 1); +} + +static inline void l2x0_inv_all(void) +{ + /* invalidate all ways */ + sync_writel(0xff, L2X0_INV_WAY, 0xff); + cache_sync(); +} + +static void l2x0_inv_range(unsigned long start, unsigned long end) +{ + unsigned long addr; + + start &= ~(CACHE_LINE_SIZE - 1); + for (addr = start; addr < end; addr += CACHE_LINE_SIZE) + sync_writel(addr, L2X0_INV_LINE_PA, 1); + cache_sync(); +} + +static void l2x0_clean_range(unsigned long start, unsigned long end) +{ + unsigned long addr; + + start &= ~(CACHE_LINE_SIZE - 1); + for (addr = start; addr < end; addr += CACHE_LINE_SIZE) + sync_writel(addr, L2X0_CLEAN_LINE_PA, 1); + cache_sync(); +} + +static void l2x0_flush_range(unsigned long start, unsigned long end) +{ + unsigned long addr; + + start &= ~(CACHE_LINE_SIZE - 1); + for (addr = start; addr < end; addr += CACHE_LINE_SIZE) + sync_writel(addr, L2X0_CLEAN_INV_LINE_PA, 1); + cache_sync(); +} + +void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask) +{ + __u32 aux; + + l2x0_base = base; + + /* disable L2X0 */ + writel(0, l2x0_base + L2X0_CTRL); + + aux = readl(l2x0_base + L2X0_AUX_CTRL); + aux &= aux_mask; + aux |= aux_val; + writel(aux, l2x0_base + L2X0_AUX_CTRL); + + l2x0_inv_all(); + + /* enable L2X0 */ + writel(1, l2x0_base + L2X0_CTRL); + + outer_cache.inv_range = l2x0_inv_range; + outer_cache.clean_range = l2x0_clean_range; + outer_cache.flush_range = l2x0_flush_range; + + printk(KERN_INFO "L2X0 cache controller enabled\n"); +} diff --git a/include/asm-arm/hardware/cache-l2x0.h b/include/asm-arm/hardware/cache-l2x0.h new file mode 100644 index 000000000000..54029a740396 --- /dev/null +++ b/include/asm-arm/hardware/cache-l2x0.h @@ -0,0 +1,56 @@ +/* + * include/asm-arm/hardware/cache-l2x0.h + * + * Copyright (C) 2007 ARM Limited + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARM_HARDWARE_L2X0_H +#define __ASM_ARM_HARDWARE_L2X0_H + +#define L2X0_CACHE_ID 0x000 +#define L2X0_CACHE_TYPE 0x004 +#define L2X0_CTRL 0x100 +#define L2X0_AUX_CTRL 0x104 +#define L2X0_EVENT_CNT_CTRL 0x200 +#define L2X0_EVENT_CNT1_CFG 0x204 +#define L2X0_EVENT_CNT0_CFG 0x208 +#define L2X0_EVENT_CNT1_VAL 0x20C +#define L2X0_EVENT_CNT0_VAL 0x210 +#define L2X0_INTR_MASK 0x214 +#define L2X0_MASKED_INTR_STAT 0x218 +#define L2X0_RAW_INTR_STAT 0x21C +#define L2X0_INTR_CLEAR 0x220 +#define L2X0_CACHE_SYNC 0x730 +#define L2X0_INV_LINE_PA 0x770 +#define L2X0_INV_WAY 0x77C +#define L2X0_CLEAN_LINE_PA 0x7B0 +#define L2X0_CLEAN_LINE_IDX 0x7B8 +#define L2X0_CLEAN_WAY 0x7BC +#define L2X0_CLEAN_INV_LINE_PA 0x7F0 +#define L2X0_CLEAN_INV_LINE_IDX 0x7F8 +#define L2X0_CLEAN_INV_WAY 0x7FC +#define L2X0_LOCKDOWN_WAY_D 0x900 +#define L2X0_LOCKDOWN_WAY_I 0x904 +#define L2X0_TEST_OPERATION 0xF00 +#define L2X0_LINE_DATA 0xF10 +#define L2X0_LINE_TAG 0xF30 +#define L2X0_DEBUG_CTRL 0xF40 + +#ifndef __ASSEMBLY__ +extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask); +#endif + +#endif -- cgit v1.2.3 From 4c784ef76ac4443ab13648859f1b2a2737546cc1 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 9 Feb 2007 19:20:47 +0100 Subject: [ARM] 4155/1: S3C24XX: remove obj-dma-* from Makefile In preperation for splitting the arch-s3c2410 directory up, remove the use of obj-dma-y in the Makefile and move to using CONFIG_S3C2440_DMA, CONFIG_S3C2412_DMA, etc. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/Kconfig | 15 ++++++++++++++- arch/arm/mach-s3c2410/Makefile | 10 ++-------- 2 files changed, 16 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index eb4ec411312b..6329b4066f78 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -192,10 +192,17 @@ config S3C2412_PM help Internal config node to apply S3C2412 power management +config S3C2412_DMA + bool + depends on CPU_S3C2412 + help + Internal config node for S3C2412 DMA support + config CPU_S3C2412 bool depends on ARCH_S3C2410 select S3C2412_PM if PM + select S3C2412_DMA if S3C2410_DMA help Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line @@ -205,11 +212,18 @@ config CPU_S3C244X help Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems. +config S3C2440_DMA + bool + depends on ARCH_S3C2410 && CPU_S3C24405B + help + Support for S3C2440 specific DMA code5A + config CPU_S3C2440 bool depends on ARCH_S3C2410 select S3C2410_CLOCK select S3C2410_PM if PM + select S3C2440_DMA if S3C2410_DMA select CPU_S3C244X help Support for S3C2440 Samsung Mobile CPU based systems. @@ -272,7 +286,6 @@ config S3C2410_DMA_DEBUG amount of time, as well as using an significant percentage of the CPU time doing so. - config S3C2410_PM_DEBUG bool "S3C2410 PM Suspend debug" depends on ARCH_S3C2410 && PM diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index 27663e28cc88..85ffa1274b0b 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -9,8 +9,6 @@ obj-y := cpu.o irq.o time.o gpio.o clock.o devs.o obj-m := obj-n := obj- := -obj-dma-y := -obj-dma-n := # DMA obj-$(CONFIG_S3C2410_DMA) += dma.o @@ -37,9 +35,9 @@ obj-$(CONFIG_PM_H1940) += pm-h1940.o obj-$(CONFIG_CPU_S3C2412) += s3c2412.o obj-$(CONFIG_CPU_S3C2412) += s3c2412-irq.o obj-$(CONFIG_CPU_S3C2412) += s3c2412-clock.o -obj-dma-$(CONFIG_CPU_S3C2412) += s3c2412-dma.o obj-$(CONFIG_S3C2412_PM) += s3c2412-pm.o +obj-$(CONFIG_S3C2412_DMA) += s3c2412-dma.o # # S3C244X support @@ -57,7 +55,7 @@ obj-$(CONFIG_CPU_S3C2440) += s3c2440.o s3c2440-dsc.o obj-$(CONFIG_CPU_S3C2440) += s3c2440-irq.o obj-$(CONFIG_CPU_S3C2440) += s3c2440-clock.o obj-$(CONFIG_CPU_S3C2440) += s3c2410-gpio.o -obj-dma-$(CONFIG_CPU_S3C2440) += s3c2440-dma.o +obj-$(CONFIG_S3C2440_DMA) += s3c2440-dma.o # S3C2442 support @@ -68,10 +66,6 @@ obj-$(CONFIG_CPU_S3C2442) += s3c2442-clock.o obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o -# merge in dma objects - -obj-y += $(obj-dma-y) - # machine specific support obj-$(CONFIG_MACH_AML_M5900) += mach-amlm5900.o -- cgit v1.2.3 From d19494b187b20e363f9b434b9ceab4159ac88324 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 9 Feb 2007 19:24:45 +0100 Subject: [ARM] 4156/1: S3C24XX: Add CONFIG_S3C2410_GPIO In preperation for splitting the arch-s3c2410 directory up, add a CONFIG_S3C2410_GPIO instead of implicitly making the .o for CONFIG_CPU_S3C2410 and CONFIG_CPU_S3C2440 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/Kconfig | 8 ++++++++ arch/arm/mach-s3c2410/Makefile | 3 +-- 2 files changed, 9 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 6329b4066f78..0ab590ec4582 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -158,6 +158,11 @@ config S3C2410_CLOCK help Clock code for the S3C2410, and similar processors +config S3C2410_GPIO + bool + help + GPIO code for S3C2410 and similar processors + config S3C2410_PM bool help @@ -174,6 +179,7 @@ config CPU_S3C2410 bool depends on ARCH_S3C2410 select S3C2410_CLOCK + select S3C2410_GPIO select S3C2410_PM if PM help Support for S3C2410 and S3C2410A family from the S3C24XX line @@ -223,6 +229,7 @@ config CPU_S3C2440 depends on ARCH_S3C2410 select S3C2410_CLOCK select S3C2410_PM if PM + select S3C2410_GPIO select S3C2440_DMA if S3C2410_DMA select CPU_S3C244X help @@ -232,6 +239,7 @@ config CPU_S3C2442 bool depends on ARCH_S3C2420 select S3C2410_CLOCK + select S3C2410_GPIO select S3C2410_PM if PM select CPU_S3C244X help diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index 85ffa1274b0b..1cc5febdaabd 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -19,10 +19,10 @@ obj-$(CONFIG_CPU_S3C2400) += s3c2400-gpio.o # S3C2410 support files obj-$(CONFIG_CPU_S3C2410) += s3c2410.o -obj-$(CONFIG_CPU_S3C2410) += s3c2410-gpio.o obj-$(CONFIG_CPU_S3C2410) += s3c2410-irq.o obj-$(CONFIG_S3C2410_PM) += s3c2410-pm.o s3c2410-sleep.o +obj-$(CONFIG_S3C2410_GPIO) += s3c2410-gpio.o obj-$(CONFIG_CPU_S3C2410_DMA) += s3c2410-dma.o # Power Management support @@ -54,7 +54,6 @@ obj-$(CONFIG_S3C2410_CLOCK) += s3c2410-clock.o obj-$(CONFIG_CPU_S3C2440) += s3c2440.o s3c2440-dsc.o obj-$(CONFIG_CPU_S3C2440) += s3c2440-irq.o obj-$(CONFIG_CPU_S3C2440) += s3c2440-clock.o -obj-$(CONFIG_CPU_S3C2440) += s3c2410-gpio.o obj-$(CONFIG_S3C2440_DMA) += s3c2440-dma.o # S3C2442 support -- cgit v1.2.3 From 44b18693904e65d840ae999ac8aa717551cf509f Mon Sep 17 00:00:00 2001 From: Imre_Deak Date: Sun, 11 Feb 2007 13:45:13 +0100 Subject: [ARM] 4158/1: Fix user page protection macros The PAGE_* user page protection macros don't take into account the configured memory policy and other architecture specific bits like the global/ASID and shared mapping bits. Instead of constants let these depend on a variable fixed up at init just like PAGE_KERNEL. Signed-off-by: Imre Deak Signed-off-by: Russell King --- arch/arm/mm/mmu.c | 3 +++ include/asm-arm/pgtable.h | 54 ++++++++++++++++++++++++++++------------------- 2 files changed, 35 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 655c8376f0b5..94fd4bf5cb9e 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -49,8 +49,10 @@ pmd_t *top_pmd; static unsigned int cachepolicy __initdata = CPOLICY_WRITEBACK; static unsigned int ecc_mask __initdata = 0; +pgprot_t pgprot_user; pgprot_t pgprot_kernel; +EXPORT_SYMBOL(pgprot_user); EXPORT_SYMBOL(pgprot_kernel); struct cachepolicy { @@ -345,6 +347,7 @@ static void __init build_mem_type_table(void) mem_types[MT_MINICLEAN].prot_sect &= ~PMD_SECT_TEX(1); } + pgprot_user = __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | user_pgprot); pgprot_kernel = __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY | L_PTE_WRITE | L_PTE_EXEC | kern_pgprot); diff --git a/include/asm-arm/pgtable.h b/include/asm-arm/pgtable.h index b8cf2d5ec304..7b2bafce21a2 100644 --- a/include/asm-arm/pgtable.h +++ b/include/asm-arm/pgtable.h @@ -175,19 +175,29 @@ extern void __pgd_error(const char *file, int line, unsigned long val); #ifndef __ASSEMBLY__ /* - * The following macros handle the cache and bufferable bits... + * The pgprot_* and protection_map entries will be fixed up in runtime + * to include the cachable and bufferable bits based on memory policy, + * as well as any architecture dependent bits like global/ASID and SMP + * shared mapping bits. */ #define _L_PTE_DEFAULT L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_CACHEABLE | L_PTE_BUFFERABLE #define _L_PTE_READ L_PTE_USER | L_PTE_EXEC +extern pgprot_t pgprot_user; extern pgprot_t pgprot_kernel; -#define PAGE_NONE __pgprot(_L_PTE_DEFAULT) -#define PAGE_COPY __pgprot(_L_PTE_DEFAULT | _L_PTE_READ) -#define PAGE_SHARED __pgprot(_L_PTE_DEFAULT | _L_PTE_READ | L_PTE_WRITE) -#define PAGE_READONLY __pgprot(_L_PTE_DEFAULT | _L_PTE_READ) +#define PAGE_NONE pgprot_user +#define PAGE_COPY __pgprot(pgprot_val(pgprot_user) | _L_PTE_READ) +#define PAGE_SHARED __pgprot(pgprot_val(pgprot_user) | _L_PTE_READ | \ + L_PTE_WRITE) +#define PAGE_READONLY __pgprot(pgprot_val(pgprot_user) | _L_PTE_READ) #define PAGE_KERNEL pgprot_kernel +#define __PAGE_NONE __pgprot(_L_PTE_DEFAULT) +#define __PAGE_COPY __pgprot(_L_PTE_DEFAULT | _L_PTE_READ) +#define __PAGE_SHARED __pgprot(_L_PTE_DEFAULT | _L_PTE_READ | L_PTE_WRITE) +#define __PAGE_READONLY __pgprot(_L_PTE_DEFAULT | _L_PTE_READ) + #endif /* __ASSEMBLY__ */ /* @@ -198,23 +208,23 @@ extern pgprot_t pgprot_kernel; * 2) If we could do execute protection, then read is implied * 3) write implies read permissions */ -#define __P000 PAGE_NONE -#define __P001 PAGE_READONLY -#define __P010 PAGE_COPY -#define __P011 PAGE_COPY -#define __P100 PAGE_READONLY -#define __P101 PAGE_READONLY -#define __P110 PAGE_COPY -#define __P111 PAGE_COPY - -#define __S000 PAGE_NONE -#define __S001 PAGE_READONLY -#define __S010 PAGE_SHARED -#define __S011 PAGE_SHARED -#define __S100 PAGE_READONLY -#define __S101 PAGE_READONLY -#define __S110 PAGE_SHARED -#define __S111 PAGE_SHARED +#define __P000 __PAGE_NONE +#define __P001 __PAGE_READONLY +#define __P010 __PAGE_COPY +#define __P011 __PAGE_COPY +#define __P100 __PAGE_READONLY +#define __P101 __PAGE_READONLY +#define __P110 __PAGE_COPY +#define __P111 __PAGE_COPY + +#define __S000 __PAGE_NONE +#define __S001 __PAGE_READONLY +#define __S010 __PAGE_SHARED +#define __S011 __PAGE_SHARED +#define __S100 __PAGE_READONLY +#define __S101 __PAGE_READONLY +#define __S110 __PAGE_SHARED +#define __S111 __PAGE_SHARED #ifndef __ASSEMBLY__ /* -- cgit v1.2.3 From a21765a70ec06be175d3997320a83fa66fcc8955 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sun, 11 Feb 2007 18:31:01 +0100 Subject: [ARM] 4157/2: S3C24XX: move arch/arch/mach-s3c2410 into cpu components The following patch and script moves the arch/arm/mach-s3c2410 directory into arch/arm/plat-s3c24xx for the generic core code and inti arch/arm/mach-s3c{cpu} for the cpu/machine support files Include directory include/asm-arm/plat-s3c24xx is added for the core include files. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/Kconfig | 8 + arch/arm/Makefile | 7 +- arch/arm/mach-s3c2400/Kconfig | 13 + arch/arm/mach-s3c2400/Makefile | 15 + arch/arm/mach-s3c2400/gpio.c | 42 + arch/arm/mach-s3c2410/Kconfig | 356 ++----- arch/arm/mach-s3c2410/Makefile | 95 +- arch/arm/mach-s3c2410/bast-irq.c | 2 +- arch/arm/mach-s3c2410/bast.h | 2 +- arch/arm/mach-s3c2410/clock.c | 565 ++++------ arch/arm/mach-s3c2410/clock.h | 63 -- arch/arm/mach-s3c2410/common-smdk.c | 200 ---- arch/arm/mach-s3c2410/common-smdk.h | 15 - arch/arm/mach-s3c2410/cpu.c | 357 ------- arch/arm/mach-s3c2410/cpu.h | 69 -- arch/arm/mach-s3c2410/devs.c | 585 ----------- arch/arm/mach-s3c2410/devs.h | 51 - arch/arm/mach-s3c2410/dma.c | 1528 +++------------------------- arch/arm/mach-s3c2410/dma.h | 45 - arch/arm/mach-s3c2410/gpio.c | 165 +-- arch/arm/mach-s3c2410/irq.c | 775 +------------- arch/arm/mach-s3c2410/irq.h | 107 -- arch/arm/mach-s3c2410/mach-amlm5900.c | 6 +- arch/arm/mach-s3c2410/mach-anubis.c | 325 ------ arch/arm/mach-s3c2410/mach-bast.c | 6 +- arch/arm/mach-s3c2410/mach-h1940.c | 8 +- arch/arm/mach-s3c2410/mach-n30.c | 8 +- arch/arm/mach-s3c2410/mach-nexcoder.c | 158 --- arch/arm/mach-s3c2410/mach-osiris.c | 303 ------ arch/arm/mach-s3c2410/mach-otom.c | 8 +- arch/arm/mach-s3c2410/mach-rx3715.c | 244 ----- arch/arm/mach-s3c2410/mach-smdk2410.c | 8 +- arch/arm/mach-s3c2410/mach-smdk2413.c | 140 --- arch/arm/mach-s3c2410/mach-smdk2440.c | 208 ---- arch/arm/mach-s3c2410/mach-vr1000.c | 6 +- arch/arm/mach-s3c2410/mach-vstms.c | 169 --- arch/arm/mach-s3c2410/pm-simtec.c | 66 -- arch/arm/mach-s3c2410/pm.c | 653 ++---------- arch/arm/mach-s3c2410/pm.h | 73 -- arch/arm/mach-s3c2410/s3c2400-gpio.c | 42 - arch/arm/mach-s3c2410/s3c2400.h | 31 - arch/arm/mach-s3c2410/s3c2410-clock.c | 276 ----- arch/arm/mach-s3c2410/s3c2410-dma.c | 161 --- arch/arm/mach-s3c2410/s3c2410-gpio.c | 71 -- arch/arm/mach-s3c2410/s3c2410-irq.c | 48 - arch/arm/mach-s3c2410/s3c2410-pm.c | 156 --- arch/arm/mach-s3c2410/s3c2410-sleep.S | 68 -- arch/arm/mach-s3c2410/s3c2410.c | 8 +- arch/arm/mach-s3c2410/s3c2410.h | 31 - arch/arm/mach-s3c2410/s3c2412-clock.c | 716 ------------- arch/arm/mach-s3c2410/s3c2412-dma.c | 161 --- arch/arm/mach-s3c2410/s3c2412-irq.c | 133 --- arch/arm/mach-s3c2410/s3c2412-pm.c | 128 --- arch/arm/mach-s3c2410/s3c2412.c | 181 ---- arch/arm/mach-s3c2410/s3c2412.h | 29 - arch/arm/mach-s3c2410/s3c2440-clock.c | 170 ---- arch/arm/mach-s3c2410/s3c2440-dma.c | 165 --- arch/arm/mach-s3c2410/s3c2440-dsc.c | 54 - arch/arm/mach-s3c2410/s3c2440-irq.c | 130 --- arch/arm/mach-s3c2410/s3c2440.c | 52 - arch/arm/mach-s3c2410/s3c2440.h | 17 - arch/arm/mach-s3c2410/s3c2442-clock.c | 171 ---- arch/arm/mach-s3c2410/s3c2442.c | 34 - arch/arm/mach-s3c2410/s3c2442.h | 17 - arch/arm/mach-s3c2410/s3c244x-irq.c | 146 --- arch/arm/mach-s3c2410/s3c244x.c | 184 ---- arch/arm/mach-s3c2410/s3c244x.h | 25 - arch/arm/mach-s3c2410/sleep.S | 151 +-- arch/arm/mach-s3c2410/time.c | 262 ----- arch/arm/mach-s3c2410/usb-simtec.c | 2 +- arch/arm/mach-s3c2412/Kconfig | 58 ++ arch/arm/mach-s3c2412/Makefile | 21 + arch/arm/mach-s3c2412/clock.c | 716 +++++++++++++ arch/arm/mach-s3c2412/dma.c | 161 +++ arch/arm/mach-s3c2412/irq.c | 133 +++ arch/arm/mach-s3c2412/mach-smdk2413.c | 140 +++ arch/arm/mach-s3c2412/mach-vstms.c | 169 +++ arch/arm/mach-s3c2412/pm.c | 128 +++ arch/arm/mach-s3c2412/s3c2412.c | 181 ++++ arch/arm/mach-s3c2440/Kconfig | 71 ++ arch/arm/mach-s3c2440/Makefile | 23 + arch/arm/mach-s3c2440/clock.c | 170 ++++ arch/arm/mach-s3c2440/dma.c | 165 +++ arch/arm/mach-s3c2440/dsc.c | 54 + arch/arm/mach-s3c2440/irq.c | 130 +++ arch/arm/mach-s3c2440/mach-anubis.c | 325 ++++++ arch/arm/mach-s3c2440/mach-nexcoder.c | 158 +++ arch/arm/mach-s3c2440/mach-osiris.c | 303 ++++++ arch/arm/mach-s3c2440/mach-rx3715.c | 244 +++++ arch/arm/mach-s3c2440/mach-smdk2440.c | 208 ++++ arch/arm/mach-s3c2440/s3c2440.c | 52 + arch/arm/mach-s3c2442/Kconfig | 27 + arch/arm/mach-s3c2442/Makefile | 16 + arch/arm/mach-s3c2442/clock.c | 171 ++++ arch/arm/mach-s3c2442/s3c2442.c | 34 + arch/arm/plat-s3c24xx/Kconfig | 96 ++ arch/arm/plat-s3c24xx/Makefile | 30 + arch/arm/plat-s3c24xx/clock.c | 449 ++++++++ arch/arm/plat-s3c24xx/common-smdk.c | 200 ++++ arch/arm/plat-s3c24xx/cpu.c | 357 +++++++ arch/arm/plat-s3c24xx/devs.c | 585 +++++++++++ arch/arm/plat-s3c24xx/dma.c | 1441 ++++++++++++++++++++++++++ arch/arm/plat-s3c24xx/gpio.c | 188 ++++ arch/arm/plat-s3c24xx/irq.c | 801 +++++++++++++++ arch/arm/plat-s3c24xx/pm-simtec.c | 66 ++ arch/arm/plat-s3c24xx/pm.c | 659 ++++++++++++ arch/arm/plat-s3c24xx/s3c244x-irq.c | 146 +++ arch/arm/plat-s3c24xx/s3c244x.c | 184 ++++ arch/arm/plat-s3c24xx/s3c244x.h | 25 + arch/arm/plat-s3c24xx/sleep.S | 159 +++ arch/arm/plat-s3c24xx/time.c | 262 +++++ include/asm-arm/plat-s3c24xx/clock.h | 63 ++ include/asm-arm/plat-s3c24xx/common-smdk.h | 15 + include/asm-arm/plat-s3c24xx/cpu.h | 69 ++ include/asm-arm/plat-s3c24xx/devs.h | 51 + include/asm-arm/plat-s3c24xx/dma.h | 45 + include/asm-arm/plat-s3c24xx/irq.h | 107 ++ include/asm-arm/plat-s3c24xx/pm.h | 73 ++ include/asm-arm/plat-s3c24xx/s3c2400.h | 31 + include/asm-arm/plat-s3c24xx/s3c2410.h | 31 + include/asm-arm/plat-s3c24xx/s3c2412.h | 29 + include/asm-arm/plat-s3c24xx/s3c2440.h | 17 + include/asm-arm/plat-s3c24xx/s3c2442.h | 17 + 123 files changed, 10711 insertions(+), 10617 deletions(-) create mode 100644 arch/arm/mach-s3c2400/Kconfig create mode 100644 arch/arm/mach-s3c2400/Makefile create mode 100644 arch/arm/mach-s3c2400/gpio.c delete mode 100644 arch/arm/mach-s3c2410/clock.h delete mode 100644 arch/arm/mach-s3c2410/common-smdk.c delete mode 100644 arch/arm/mach-s3c2410/common-smdk.h delete mode 100644 arch/arm/mach-s3c2410/cpu.c delete mode 100644 arch/arm/mach-s3c2410/cpu.h delete mode 100644 arch/arm/mach-s3c2410/devs.c delete mode 100644 arch/arm/mach-s3c2410/devs.h delete mode 100644 arch/arm/mach-s3c2410/dma.h delete mode 100644 arch/arm/mach-s3c2410/irq.h delete mode 100644 arch/arm/mach-s3c2410/mach-anubis.c delete mode 100644 arch/arm/mach-s3c2410/mach-nexcoder.c delete mode 100644 arch/arm/mach-s3c2410/mach-osiris.c delete mode 100644 arch/arm/mach-s3c2410/mach-rx3715.c delete mode 100644 arch/arm/mach-s3c2410/mach-smdk2413.c delete mode 100644 arch/arm/mach-s3c2410/mach-smdk2440.c delete mode 100644 arch/arm/mach-s3c2410/mach-vstms.c delete mode 100644 arch/arm/mach-s3c2410/pm-simtec.c delete mode 100644 arch/arm/mach-s3c2410/pm.h delete mode 100644 arch/arm/mach-s3c2410/s3c2400-gpio.c delete mode 100644 arch/arm/mach-s3c2410/s3c2400.h delete mode 100644 arch/arm/mach-s3c2410/s3c2410-clock.c delete mode 100644 arch/arm/mach-s3c2410/s3c2410-dma.c delete mode 100644 arch/arm/mach-s3c2410/s3c2410-gpio.c delete mode 100644 arch/arm/mach-s3c2410/s3c2410-irq.c delete mode 100644 arch/arm/mach-s3c2410/s3c2410-pm.c delete mode 100644 arch/arm/mach-s3c2410/s3c2410-sleep.S delete mode 100644 arch/arm/mach-s3c2410/s3c2410.h delete mode 100644 arch/arm/mach-s3c2410/s3c2412-clock.c delete mode 100644 arch/arm/mach-s3c2410/s3c2412-dma.c delete mode 100644 arch/arm/mach-s3c2410/s3c2412-irq.c delete mode 100644 arch/arm/mach-s3c2410/s3c2412-pm.c delete mode 100644 arch/arm/mach-s3c2410/s3c2412.c delete mode 100644 arch/arm/mach-s3c2410/s3c2412.h delete mode 100644 arch/arm/mach-s3c2410/s3c2440-clock.c delete mode 100644 arch/arm/mach-s3c2410/s3c2440-dma.c delete mode 100644 arch/arm/mach-s3c2410/s3c2440-dsc.c delete mode 100644 arch/arm/mach-s3c2410/s3c2440-irq.c delete mode 100644 arch/arm/mach-s3c2410/s3c2440.c delete mode 100644 arch/arm/mach-s3c2410/s3c2440.h delete mode 100644 arch/arm/mach-s3c2410/s3c2442-clock.c delete mode 100644 arch/arm/mach-s3c2410/s3c2442.c delete mode 100644 arch/arm/mach-s3c2410/s3c2442.h delete mode 100644 arch/arm/mach-s3c2410/s3c244x-irq.c delete mode 100644 arch/arm/mach-s3c2410/s3c244x.c delete mode 100644 arch/arm/mach-s3c2410/s3c244x.h delete mode 100644 arch/arm/mach-s3c2410/time.c create mode 100644 arch/arm/mach-s3c2412/Kconfig create mode 100644 arch/arm/mach-s3c2412/Makefile create mode 100644 arch/arm/mach-s3c2412/clock.c create mode 100644 arch/arm/mach-s3c2412/dma.c create mode 100644 arch/arm/mach-s3c2412/irq.c create mode 100644 arch/arm/mach-s3c2412/mach-smdk2413.c create mode 100644 arch/arm/mach-s3c2412/mach-vstms.c create mode 100644 arch/arm/mach-s3c2412/pm.c create mode 100644 arch/arm/mach-s3c2412/s3c2412.c create mode 100644 arch/arm/mach-s3c2440/Kconfig create mode 100644 arch/arm/mach-s3c2440/Makefile create mode 100644 arch/arm/mach-s3c2440/clock.c create mode 100644 arch/arm/mach-s3c2440/dma.c create mode 100644 arch/arm/mach-s3c2440/dsc.c create mode 100644 arch/arm/mach-s3c2440/irq.c create mode 100644 arch/arm/mach-s3c2440/mach-anubis.c create mode 100644 arch/arm/mach-s3c2440/mach-nexcoder.c create mode 100644 arch/arm/mach-s3c2440/mach-osiris.c create mode 100644 arch/arm/mach-s3c2440/mach-rx3715.c create mode 100644 arch/arm/mach-s3c2440/mach-smdk2440.c create mode 100644 arch/arm/mach-s3c2440/s3c2440.c create mode 100644 arch/arm/mach-s3c2442/Kconfig create mode 100644 arch/arm/mach-s3c2442/Makefile create mode 100644 arch/arm/mach-s3c2442/clock.c create mode 100644 arch/arm/mach-s3c2442/s3c2442.c create mode 100644 arch/arm/plat-s3c24xx/Kconfig create mode 100644 arch/arm/plat-s3c24xx/Makefile create mode 100644 arch/arm/plat-s3c24xx/clock.c create mode 100644 arch/arm/plat-s3c24xx/common-smdk.c create mode 100644 arch/arm/plat-s3c24xx/cpu.c create mode 100644 arch/arm/plat-s3c24xx/devs.c create mode 100644 arch/arm/plat-s3c24xx/dma.c create mode 100644 arch/arm/plat-s3c24xx/gpio.c create mode 100644 arch/arm/plat-s3c24xx/irq.c create mode 100644 arch/arm/plat-s3c24xx/pm-simtec.c create mode 100644 arch/arm/plat-s3c24xx/pm.c create mode 100644 arch/arm/plat-s3c24xx/s3c244x-irq.c create mode 100644 arch/arm/plat-s3c24xx/s3c244x.c create mode 100644 arch/arm/plat-s3c24xx/s3c244x.h create mode 100644 arch/arm/plat-s3c24xx/sleep.S create mode 100644 arch/arm/plat-s3c24xx/time.c create mode 100644 include/asm-arm/plat-s3c24xx/clock.h create mode 100644 include/asm-arm/plat-s3c24xx/common-smdk.h create mode 100644 include/asm-arm/plat-s3c24xx/cpu.h create mode 100644 include/asm-arm/plat-s3c24xx/devs.h create mode 100644 include/asm-arm/plat-s3c24xx/dma.h create mode 100644 include/asm-arm/plat-s3c24xx/irq.h create mode 100644 include/asm-arm/plat-s3c24xx/pm.h create mode 100644 include/asm-arm/plat-s3c24xx/s3c2400.h create mode 100644 include/asm-arm/plat-s3c24xx/s3c2410.h create mode 100644 include/asm-arm/plat-s3c24xx/s3c2412.h create mode 100644 include/asm-arm/plat-s3c24xx/s3c2440.h create mode 100644 include/asm-arm/plat-s3c24xx/s3c2442.h (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6783c2e5512d..51ee13e7c74c 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -363,7 +363,15 @@ source "arch/arm/mach-omap1/Kconfig" source "arch/arm/mach-omap2/Kconfig" +source "arch/arm/plat-s3c24xx/Kconfig" + +if ARCH_S3C2410 +source "arch/arm/mach-s3c2400/Kconfig" source "arch/arm/mach-s3c2410/Kconfig" +source "arch/arm/mach-s3c2412/Kconfig" +source "arch/arm/mach-s3c2440/Kconfig" +source "arch/arm/mach-s3c2442/Kconfig" +endif source "arch/arm/mach-lh7a40x/Kconfig" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 000f1100b553..2df1ea0a0c2d 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -149,7 +149,7 @@ MACHINE := arch/arm/mach-$(machine-y)/ else MACHINE := endif - + export TEXT_OFFSET GZFLAGS MMUEXT # Do we have FASTFPE? @@ -161,6 +161,10 @@ endif # If we have a machine-specific directory, then include it in the build. core-y += arch/arm/kernel/ arch/arm/mm/ arch/arm/common/ core-y += $(MACHINE) +core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2400/ +core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2412/ +core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2440/ +core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2442/ core-$(CONFIG_FPE_NWFPE) += arch/arm/nwfpe/ core-$(CONFIG_FPE_FASTFPE) += $(FASTFPE_OBJ) core-$(CONFIG_VFP) += arch/arm/vfp/ @@ -168,6 +172,7 @@ core-$(CONFIG_VFP) += arch/arm/vfp/ # If we have a common platform directory, then include it in the build. core-$(CONFIG_PLAT_IOP) += arch/arm/plat-iop/ core-$(CONFIG_ARCH_OMAP) += arch/arm/plat-omap/ +core-$(CONFIG_PLAT_S3C24XX) += arch/arm/plat-s3c24xx/ drivers-$(CONFIG_OPROFILE) += arch/arm/oprofile/ drivers-$(CONFIG_ARCH_CLPS7500) += drivers/acorn/char/ diff --git a/arch/arm/mach-s3c2400/Kconfig b/arch/arm/mach-s3c2400/Kconfig new file mode 100644 index 000000000000..deab0722836e --- /dev/null +++ b/arch/arm/mach-s3c2400/Kconfig @@ -0,0 +1,13 @@ +# arch/arm/mach-s3c2400/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + + + +menu "S3C2400 Machines" + + +endmenu + diff --git a/arch/arm/mach-s3c2400/Makefile b/arch/arm/mach-s3c2400/Makefile new file mode 100644 index 000000000000..7e23f4e13766 --- /dev/null +++ b/arch/arm/mach-s3c2400/Makefile @@ -0,0 +1,15 @@ +# arch/arm/mach-s3c2400/Makefile +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +obj-y := +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_CPU_S3C2400) += gpio.o + +# Machine support + diff --git a/arch/arm/mach-s3c2400/gpio.c b/arch/arm/mach-s3c2400/gpio.c new file mode 100644 index 000000000000..758e160410e9 --- /dev/null +++ b/arch/arm/mach-s3c2400/gpio.c @@ -0,0 +1,42 @@ +/* linux/arch/arm/mach-s3c2400/gpio.c + * + * Copyright (c) 2006 Lucas Correia Villa Real + * + * S3C2400 GPIO support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +int s3c2400_gpio_getirq(unsigned int pin) +{ + if (pin < S3C2410_GPE0 || pin > S3C2400_GPE7_EINT7) + return -1; /* not valid interrupts */ + + return (pin - S3C2410_GPE0) + IRQ_EINT0; +} + +EXPORT_SYMBOL(s3c2400_gpio_getirq); diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 0ab590ec4582..016b53f5d6fc 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -1,54 +1,51 @@ -if ARCH_S3C2410 +# arch/arm/mach-s3c2410/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 -menu "S3C24XX Implementations" +config CPU_S3C2410 + bool + depends on ARCH_S3C2410 + select S3C2410_CLOCK + select S3C2410_GPIO + select S3C2410_PM if PM + help + Support for S3C2410 and S3C2410A family from the S3C24XX line + of Samsung Mobile CPUs. -config MACH_AML_M5900 - bool "AML M5900 Series" - select CPU_S3C2410 - select PM_SIMTEC if PM +config CPU_S3C2410_DMA + bool + depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442) + default y if CPU_S3C2410 || CPU_S3C2442 help - Say Y here if you are using the American Microsystems M5900 Series - + DMA device selection for S3C2410 and compatible CPUs -config MACH_ANUBIS - bool "Simtec Electronics ANUBIS" - select CPU_S3C2440 - select PM_SIMTEC if PM +config S3C2410_PM + bool help - Say Y here if you are using the Simtec Electronics ANUBIS - development system + Power Management code common to S3C2410 and better -config MACH_OSIRIS - bool "Simtec IM2440D20 (OSIRIS) module" - select CPU_S3C2440 - select PM_SIMTEC if PM +config S3C2410_GPIO + bool help - Say Y here if you are using the Simtec IM2440D20 module, also - known as the Osiris. + GPIO code for S3C2410 and similar processors -config ARCH_BAST - bool "Simtec Electronics BAST (EB2410ITX)" - select CPU_S3C2410 - select PM_SIMTEC if PM - select ISA +config S3C2410_CLOCK + bool help - Say Y here if you are using the Simtec Electronics EB2410ITX - development board (also known as BAST) + Clock code for the S3C2410, and similar processors - Product page: . -config BAST_PC104_IRQ - bool "BAST PC104 IRQ support" - depends on ARCH_BAST - default y - help - Say Y here to enable the PC104 IRQ routing on the - Simtec BAST (EB2410ITX) +menu "S3C2410 Machines" -config PM_H1940 - bool +config ARCH_SMDK2410 + bool "SMDK2410/A9M2410" + select CPU_S3C2410 + select MACH_SMDK help - Internal node for H1940 and related PM + Say Y here if you are using the SMDK2410 or the derived module A9M2410 + config ARCH_H1940 bool "IPAQ H1940" @@ -57,7 +54,10 @@ config ARCH_H1940 help Say Y here if you are using the HP IPAQ H1940 - . +config PM_H1940 + bool + help + Internal node for H1940 and related PM config MACH_N30 bool "Acer N30" @@ -65,53 +65,36 @@ config MACH_N30 help Say Y here if you are using the Acer N30 - . - -config MACH_SMDK - bool - help - Common machine code for SMDK2410 and SMDK2440 - -config ARCH_SMDK2410 - bool "SMDK2410/A9M2410" +config ARCH_BAST + bool "Simtec Electronics BAST (EB2410ITX)" select CPU_S3C2410 - select MACH_SMDK + select PM_SIMTEC if PM + select ISA help - Say Y here if you are using the SMDK2410 or the derived module A9M2410 - + Say Y here if you are using the Simtec Electronics EB2410ITX + development board (also known as BAST) -config ARCH_S3C2440 - bool "SMDK2440" - select CPU_S3C2440 - select MACH_SMDK +config MACH_OTOM + bool "NexVision OTOM Board" + select CPU_S3C2410 help - Say Y here if you are using the SMDK2440. - -config SMDK2440_CPU2440 - bool "SMDK2440 with S3C2440 CPU module" - depends on ARCH_S3C2440 - default y if ARCH_S3C2440 - select CPU_S3C2440 - -config SMDK2440_CPU2442 - bool "SMDM2440 with S3C2442 CPU module" - depends on ARCH_S3C2440 - select CPU_S3C2442 + Say Y here if you are using the Nex Vision OTOM board -config MACH_S3C2413 - bool +config MACH_AML_M5900 + bool "AML M5900 Series" + select CPU_S3C2410 + select PM_SIMTEC if PM help - Internal node for S3C2413 version of SMDK2413, so that - machine_is_s3c2413() will work when MACH_SMDK2413 is - selected + Say Y here if you are using the American Microsystems M5900 Series + -config MACH_SMDK2413 - bool "SMDK2413" - select CPU_S3C2412 - select MACH_S3C2413 - select MACH_SMDK +config BAST_PC104_IRQ + bool "BAST PC104 IRQ support" + depends on ARCH_BAST + default y help - Say Y here if you are using an SMDK2413 + Say Y here to enable the PC104 IRQ routing on the + Simtec BAST (EB2410ITX) config MACH_VR1000 bool "Thorcom VR1000" @@ -120,223 +103,6 @@ config MACH_VR1000 help Say Y here if you are using the Thorcom VR1000 board. - This linux port is currently being maintained by Simtec, on behalf - of Thorcom. Any queries, please contact Thorcom first. - -config MACH_RX3715 - bool "HP iPAQ rx3715" - select CPU_S3C2440 - select PM_H1940 if PM - help - Say Y here if you are using the HP iPAQ rx3715. - - See for more - information on this project - -config MACH_OTOM - bool "NexVision OTOM Board" - select CPU_S3C2410 - help - Say Y here if you are using the Nex Vision OTOM board - -config MACH_NEXCODER_2440 - bool "NexVision NEXCODER 2440 Light Board" - select CPU_S3C2440 - help - Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board - -config MACH_VSTMS - bool "VMSTMS" - select CPU_S3C2412 - help - Say Y here if you are using an VSTMS board endmenu -config S3C2410_CLOCK - bool - help - Clock code for the S3C2410, and similar processors - -config S3C2410_GPIO - bool - help - GPIO code for S3C2410 and similar processors - -config S3C2410_PM - bool - help - Power Management code common to S3C2410 and better - -config CPU_S3C2410_DMA - bool - depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442) - default y if CPU_S3C2410 || CPU_S3C2442 - help - DMA device selection for S3C2410 and compatible CPUs - -config CPU_S3C2410 - bool - depends on ARCH_S3C2410 - select S3C2410_CLOCK - select S3C2410_GPIO - select S3C2410_PM if PM - help - Support for S3C2410 and S3C2410A family from the S3C24XX line - of Samsung Mobile CPUs. - -# internal node to signify if we are only dealing with an S3C2412 - -config CPU_S3C2412_ONLY - bool - depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \ - !CPU_S3C2440 && !CPU_S3C2442 && CPU_S3C2412 - default y if CPU_S3C2412 - -config S3C2412_PM - bool - help - Internal config node to apply S3C2412 power management - -config S3C2412_DMA - bool - depends on CPU_S3C2412 - help - Internal config node for S3C2412 DMA support - -config CPU_S3C2412 - bool - depends on ARCH_S3C2410 - select S3C2412_PM if PM - select S3C2412_DMA if S3C2410_DMA - help - Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line - -config CPU_S3C244X - bool - depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442) - help - Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems. - -config S3C2440_DMA - bool - depends on ARCH_S3C2410 && CPU_S3C24405B - help - Support for S3C2440 specific DMA code5A - -config CPU_S3C2440 - bool - depends on ARCH_S3C2410 - select S3C2410_CLOCK - select S3C2410_PM if PM - select S3C2410_GPIO - select S3C2440_DMA if S3C2410_DMA - select CPU_S3C244X - help - Support for S3C2440 Samsung Mobile CPU based systems. - -config CPU_S3C2442 - bool - depends on ARCH_S3C2420 - select S3C2410_CLOCK - select S3C2410_GPIO - select S3C2410_PM if PM - select CPU_S3C244X - help - Support for S3C2442 Samsung Mobile CPU based systems. - -comment "S3C2410 Boot" - -config S3C2410_BOOT_WATCHDOG - bool "S3C2410 Initialisation watchdog" - depends on ARCH_S3C2410 && S3C2410_WATCHDOG - help - Say y to enable the watchdog during the kernel decompression - stage. If the kernel fails to uncompress, then the watchdog - will trigger a reset and the system should restart. - - Although this uses the same hardware unit as the kernel watchdog - driver, it is not a replacement for it. If you use this option, - you will have to use the watchdg driver to either stop the timeout - or restart it. If you do not, then your kernel will reboot after - startup. - - The driver uses a fixed timeout value, so the exact time till the - system resets depends on the value of PCLK. The timeout on an - 200MHz s3c2410 should be about 30 seconds. - -config S3C2410_BOOT_ERROR_RESET - bool "S3C2410 Reboot on decompression error" - depends on ARCH_S3C2410 - help - Say y here to use the watchdog to reset the system if the - kernel decompressor detects an error during decompression. - - -comment "S3C2410 Setup" - -config S3C2410_DMA - bool "S3C2410 DMA support" - depends on ARCH_S3C2410 - help - S3C2410 DMA support. This is needed for drivers like sound which - use the S3C2410's DMA system to move data to and from the - peripheral blocks. - -config S3C2410_DMA_DEBUG - bool "S3C2410 DMA support debug" - depends on ARCH_S3C2410 && S3C2410_DMA - help - Enable debugging output for the DMA code. This option sends info - to the kernel log, at priority KERN_DEBUG. - - Note, it is easy to create and fill the log buffer in a small - amount of time, as well as using an significant percentage of - the CPU time doing so. - -config S3C2410_PM_DEBUG - bool "S3C2410 PM Suspend debug" - depends on ARCH_S3C2410 && PM - help - Say Y here if you want verbose debugging from the PM Suspend and - Resume code. See - for more information. - -config S3C2410_PM_CHECK - bool "S3C2410 PM Suspend Memory CRC" - depends on ARCH_S3C2410 && PM && CRC32 - help - Enable the PM code's memory area checksum over sleep. This option - will generate CRCs of all blocks of memory, and store them before - going to sleep. The blocks are then checked on resume for any - errors. - -config S3C2410_PM_CHECK_CHUNKSIZE - int "S3C2410 PM Suspend CRC Chunksize (KiB)" - depends on ARCH_S3C2410 && PM && S3C2410_PM_CHECK - default 64 - help - Set the chunksize in Kilobytes of the CRC for checking memory - corruption over suspend and resume. A smaller value will mean that - the CRC data block will take more memory, but wil identify any - faults with better precision. - -config PM_SIMTEC - bool - help - Common power management code for systems that are - compatible with the Simtec style of power management - -config S3C2410_LOWLEVEL_UART_PORT - int "S3C2410 UART to use for low-level messages" - default 0 - help - Choice of which UART port to use for the low-level messages, - such as the `Uncompressing...` at start time. The value of - this configuration should be between zero and two. The port - must have been initialised by the boot-loader before use. - - Note, this does not affect the port used by the debug messages, - which is a separate configuration. - -endif diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index 1cc5febdaabd..b33ac5b84773 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -1,85 +1,30 @@ - +# arch/arm/mach-s3c2410/Makefile # -# Makefile for the linux kernel. +# Copyright 2007 Simtec Electronics # +# Licensed under GPLv2 -# Object file lists. - -obj-y := cpu.o irq.o time.o gpio.o clock.o devs.o -obj-m := -obj-n := -obj- := - -# DMA -obj-$(CONFIG_S3C2410_DMA) += dma.o - -# S3C2400 support files -obj-$(CONFIG_CPU_S3C2400) += s3c2400-gpio.o - -# S3C2410 support files +obj-y := +obj-m := +obj-n := +obj- := obj-$(CONFIG_CPU_S3C2410) += s3c2410.o -obj-$(CONFIG_CPU_S3C2410) += s3c2410-irq.o - -obj-$(CONFIG_S3C2410_PM) += s3c2410-pm.o s3c2410-sleep.o -obj-$(CONFIG_S3C2410_GPIO) += s3c2410-gpio.o -obj-$(CONFIG_CPU_S3C2410_DMA) += s3c2410-dma.o - -# Power Management support - -obj-$(CONFIG_PM) += pm.o sleep.o -obj-$(CONFIG_PM_SIMTEC) += pm-simtec.o -obj-$(CONFIG_PM_H1940) += pm-h1940.o - -# S3C2412 support -obj-$(CONFIG_CPU_S3C2412) += s3c2412.o -obj-$(CONFIG_CPU_S3C2412) += s3c2412-irq.o -obj-$(CONFIG_CPU_S3C2412) += s3c2412-clock.o - -obj-$(CONFIG_S3C2412_PM) += s3c2412-pm.o -obj-$(CONFIG_S3C2412_DMA) += s3c2412-dma.o - -# -# S3C244X support - -obj-$(CONFIG_CPU_S3C244X) += s3c244x.o -obj-$(CONFIG_CPU_S3C244X) += s3c244x-irq.o - -# Clock control - -obj-$(CONFIG_S3C2410_CLOCK) += s3c2410-clock.o - -# S3C2440 support +obj-$(CONFIG_CPU_S3C2410) += irq.o +obj-$(CONFIG_CPU_S3C2410_DMA) += dma.o +obj-$(CONFIG_CPU_S3C2410_DMA) += dma.o +obj-$(CONFIG_S3C2410_PM) += pm.o sleep.o +obj-$(CONFIG_S3C2410_GPIO) += gpio.o +obj-$(CONFIG_S3C2410_CLOCK) += clock.o -obj-$(CONFIG_CPU_S3C2440) += s3c2440.o s3c2440-dsc.o -obj-$(CONFIG_CPU_S3C2440) += s3c2440-irq.o -obj-$(CONFIG_CPU_S3C2440) += s3c2440-clock.o -obj-$(CONFIG_S3C2440_DMA) += s3c2440-dma.o +# Machine support -# S3C2442 support - -obj-$(CONFIG_CPU_S3C2442) += s3c2442.o -obj-$(CONFIG_CPU_S3C2442) += s3c2442-clock.o - -# bast extras - -obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o - -# machine specific support - -obj-$(CONFIG_MACH_AML_M5900) += mach-amlm5900.o -obj-$(CONFIG_MACH_ANUBIS) += mach-anubis.o -obj-$(CONFIG_MACH_OSIRIS) += mach-osiris.o -obj-$(CONFIG_ARCH_BAST) += mach-bast.o usb-simtec.o +obj-$(CONFIG_ARCH_SMDK2410) += mach-smdk2410.o obj-$(CONFIG_ARCH_H1940) += mach-h1940.o +obj-$(CONFIG_PM_H1940) += pm-h1940.o obj-$(CONFIG_MACH_N30) += mach-n30.o -obj-$(CONFIG_ARCH_SMDK2410) += mach-smdk2410.o -obj-$(CONFIG_MACH_SMDK2413) += mach-smdk2413.o -obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o -obj-$(CONFIG_MACH_VR1000) += mach-vr1000.o usb-simtec.o -obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o +obj-$(CONFIG_ARCH_BAST) += mach-bast.o usb-simtec.o obj-$(CONFIG_MACH_OTOM) += mach-otom.o -obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o -obj-$(CONFIG_MACH_VSTMS) += mach-vstms.o - -obj-$(CONFIG_MACH_SMDK) += common-smdk.o \ No newline at end of file +obj-$(CONFIG_MACH_AML_M5900) += mach-amlm5900.o +obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o +obj-$(CONFIG_MACH_VR1000) += mach-vr1000.o usb-simtec.o diff --git a/arch/arm/mach-s3c2410/bast-irq.c b/arch/arm/mach-s3c2410/bast-irq.c index 379efe70778c..daeba427d781 100644 --- a/arch/arm/mach-s3c2410/bast-irq.c +++ b/arch/arm/mach-s3c2410/bast-irq.c @@ -39,7 +39,7 @@ #include #include -#include "irq.h" +#include #if 0 #include diff --git a/arch/arm/mach-s3c2410/bast.h b/arch/arm/mach-s3c2410/bast.h index e5d03311752c..e98543742eb9 100644 --- a/arch/arm/mach-s3c2410/bast.h +++ b/arch/arm/mach-s3c2410/bast.h @@ -1,2 +1,2 @@ - +/* linux/arch/arm/mach-s3c2410/bast.h extern void bast_init_irq(void); diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c index e13fb6778890..5b4831c4c1d8 100644 --- a/arch/arm/mach-s3c2410/clock.c +++ b/arch/arm/mach-s3c2410/clock.c @@ -1,15 +1,9 @@ /* linux/arch/arm/mach-s3c2410/clock.c * - * Copyright (c) 2004-2005 Simtec Electronics + * Copyright (c) 2006 Simtec Electronics * Ben Dooks * - * S3C24XX Core clock control support - * - * Based on, and code from linux/arch/arm/mach-versatile/clock.c - ** - ** Copyright (C) 2004 ARM Limited. - ** Written by Deep Blue Solutions Limited. - * + * S3C2410,S3C2440,S3C2442 Clock control support * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -32,418 +26,251 @@ #include #include #include -#include #include -#include -#include #include #include #include +#include + +#include #include -#include #include +#include #include #include -#include "clock.h" -#include "cpu.h" - -/* clock information */ +#include +#include +#include -static LIST_HEAD(clocks); - -DEFINE_MUTEX(clocks_mutex); - -/* enable and disable calls for use with the clk struct */ - -static int clk_null_enable(struct clk *clk, int enable) +int s3c2410_clkcon_enable(struct clk *clk, int enable) { - return 0; -} - -/* Clock API calls */ + unsigned int clocks = clk->ctrlbit; + unsigned long clkcon; -struct clk *clk_get(struct device *dev, const char *id) -{ - struct clk *p; - struct clk *clk = ERR_PTR(-ENOENT); - int idno; + clkcon = __raw_readl(S3C2410_CLKCON); - if (dev == NULL || dev->bus != &platform_bus_type) - idno = -1; + if (enable) + clkcon |= clocks; else - idno = to_platform_device(dev)->id; - - mutex_lock(&clocks_mutex); - - list_for_each_entry(p, &clocks, list) { - if (p->id == idno && - strcmp(id, p->name) == 0 && - try_module_get(p->owner)) { - clk = p; - break; - } - } - - /* check for the case where a device was supplied, but the - * clock that was being searched for is not device specific */ - - if (IS_ERR(clk)) { - list_for_each_entry(p, &clocks, list) { - if (p->id == -1 && strcmp(id, p->name) == 0 && - try_module_get(p->owner)) { - clk = p; - break; - } - } - } + clkcon &= ~clocks; - mutex_unlock(&clocks_mutex); - return clk; -} + /* ensure none of the special function bits set */ + clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER); -void clk_put(struct clk *clk) -{ - module_put(clk->owner); -} + __raw_writel(clkcon, S3C2410_CLKCON); -int clk_enable(struct clk *clk) -{ - if (IS_ERR(clk) || clk == NULL) - return -EINVAL; - - clk_enable(clk->parent); - - mutex_lock(&clocks_mutex); - - if ((clk->usage++) == 0) - (clk->enable)(clk, 1); - - mutex_unlock(&clocks_mutex); return 0; } -void clk_disable(struct clk *clk) -{ - if (IS_ERR(clk) || clk == NULL) - return; - - mutex_lock(&clocks_mutex); - - if ((--clk->usage) == 0) - (clk->enable)(clk, 0); - - mutex_unlock(&clocks_mutex); - clk_disable(clk->parent); -} - - -unsigned long clk_get_rate(struct clk *clk) -{ - if (IS_ERR(clk)) - return 0; - - if (clk->rate != 0) - return clk->rate; - - if (clk->get_rate != NULL) - return (clk->get_rate)(clk); - - if (clk->parent != NULL) - return clk_get_rate(clk->parent); - - return clk->rate; -} - -long clk_round_rate(struct clk *clk, unsigned long rate) -{ - if (!IS_ERR(clk) && clk->round_rate) - return (clk->round_rate)(clk, rate); - - return rate; -} - -int clk_set_rate(struct clk *clk, unsigned long rate) -{ - int ret; - - if (IS_ERR(clk)) - return -EINVAL; - - mutex_lock(&clocks_mutex); - ret = (clk->set_rate)(clk, rate); - mutex_unlock(&clocks_mutex); - - return ret; -} - -struct clk *clk_get_parent(struct clk *clk) +static int s3c2410_upll_enable(struct clk *clk, int enable) { - return clk->parent; -} - -int clk_set_parent(struct clk *clk, struct clk *parent) -{ - int ret = 0; - - if (IS_ERR(clk)) - return -EINVAL; - - mutex_lock(&clocks_mutex); - - if (clk->set_parent) - ret = (clk->set_parent)(clk, parent); - - mutex_unlock(&clocks_mutex); - - return ret; -} - -EXPORT_SYMBOL(clk_get); -EXPORT_SYMBOL(clk_put); -EXPORT_SYMBOL(clk_enable); -EXPORT_SYMBOL(clk_disable); -EXPORT_SYMBOL(clk_get_rate); -EXPORT_SYMBOL(clk_round_rate); -EXPORT_SYMBOL(clk_set_rate); -EXPORT_SYMBOL(clk_get_parent); -EXPORT_SYMBOL(clk_set_parent); - -/* base clocks */ - -struct clk clk_xtal = { - .name = "xtal", - .id = -1, - .rate = 0, - .parent = NULL, - .ctrlbit = 0, -}; - -struct clk clk_mpll = { - .name = "mpll", - .id = -1, -}; - -struct clk clk_upll = { - .name = "upll", - .id = -1, - .parent = NULL, - .ctrlbit = 0, -}; - -struct clk clk_f = { - .name = "fclk", - .id = -1, - .rate = 0, - .parent = &clk_mpll, - .ctrlbit = 0, -}; - -struct clk clk_h = { - .name = "hclk", - .id = -1, - .rate = 0, - .parent = NULL, - .ctrlbit = 0, -}; - -struct clk clk_p = { - .name = "pclk", - .id = -1, - .rate = 0, - .parent = NULL, - .ctrlbit = 0, -}; - -struct clk clk_usb_bus = { - .name = "usb-bus", - .id = -1, - .rate = 0, - .parent = &clk_upll, -}; - -/* clocks that could be registered by external code */ - -static int s3c24xx_dclk_enable(struct clk *clk, int enable) -{ - unsigned long dclkcon = __raw_readl(S3C24XX_DCLKCON); + unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); + unsigned long orig = clkslow; if (enable) - dclkcon |= clk->ctrlbit; + clkslow &= ~S3C2410_CLKSLOW_UCLK_OFF; else - dclkcon &= ~clk->ctrlbit; + clkslow |= S3C2410_CLKSLOW_UCLK_OFF; - __raw_writel(dclkcon, S3C24XX_DCLKCON); + __raw_writel(clkslow, S3C2410_CLKSLOW); - return 0; -} + /* if we started the UPLL, then allow to settle */ -static int s3c24xx_dclk_setparent(struct clk *clk, struct clk *parent) -{ - unsigned long dclkcon; - unsigned int uclk; - - if (parent == &clk_upll) - uclk = 1; - else if (parent == &clk_p) - uclk = 0; - else - return -EINVAL; - - clk->parent = parent; - - dclkcon = __raw_readl(S3C24XX_DCLKCON); - - if (clk->ctrlbit == S3C2410_DCLKCON_DCLK0EN) { - if (uclk) - dclkcon |= S3C2410_DCLKCON_DCLK0_UCLK; - else - dclkcon &= ~S3C2410_DCLKCON_DCLK0_UCLK; - } else { - if (uclk) - dclkcon |= S3C2410_DCLKCON_DCLK1_UCLK; - else - dclkcon &= ~S3C2410_DCLKCON_DCLK1_UCLK; - } - - __raw_writel(dclkcon, S3C24XX_DCLKCON); + if (enable && (orig & S3C2410_CLKSLOW_UCLK_OFF)) + udelay(200); return 0; } - -static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent) -{ - unsigned long mask; - unsigned long source; - - /* calculate the MISCCR setting for the clock */ - - if (parent == &clk_xtal) - source = S3C2410_MISCCR_CLK0_MPLL; - else if (parent == &clk_upll) - source = S3C2410_MISCCR_CLK0_UPLL; - else if (parent == &clk_f) - source = S3C2410_MISCCR_CLK0_FCLK; - else if (parent == &clk_h) - source = S3C2410_MISCCR_CLK0_HCLK; - else if (parent == &clk_p) - source = S3C2410_MISCCR_CLK0_PCLK; - else if (clk == &s3c24xx_clkout0 && parent == &s3c24xx_dclk0) - source = S3C2410_MISCCR_CLK0_DCLK0; - else if (clk == &s3c24xx_clkout1 && parent == &s3c24xx_dclk1) - source = S3C2410_MISCCR_CLK0_DCLK0; - else - return -EINVAL; - - clk->parent = parent; - - if (clk == &s3c24xx_dclk0) - mask = S3C2410_MISCCR_CLK0_MASK; - else { - source <<= 4; - mask = S3C2410_MISCCR_CLK1_MASK; +/* standard clock definitions */ + +static struct clk init_clocks_disable[] = { + { + .name = "nand", + .id = -1, + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_NAND, + }, { + .name = "sdi", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_SDI, + }, { + .name = "adc", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_ADC, + }, { + .name = "i2c", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_IIC, + }, { + .name = "iis", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_IIS, + }, { + .name = "spi", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_SPI, } - - s3c2410_modify_misccr(mask, source); - return 0; -} - -/* external clock definitions */ - -struct clk s3c24xx_dclk0 = { - .name = "dclk0", - .id = -1, - .ctrlbit = S3C2410_DCLKCON_DCLK0EN, - .enable = s3c24xx_dclk_enable, - .set_parent = s3c24xx_dclk_setparent, -}; - -struct clk s3c24xx_dclk1 = { - .name = "dclk1", - .id = -1, - .ctrlbit = S3C2410_DCLKCON_DCLK0EN, - .enable = s3c24xx_dclk_enable, - .set_parent = s3c24xx_dclk_setparent, }; -struct clk s3c24xx_clkout0 = { - .name = "clkout0", - .id = -1, - .set_parent = s3c24xx_clkout_setparent, +static struct clk init_clocks[] = { + { + .name = "lcd", + .id = -1, + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_LCDC, + }, { + .name = "gpio", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_GPIO, + }, { + .name = "usb-host", + .id = -1, + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_USBH, + }, { + .name = "usb-device", + .id = -1, + .parent = &clk_h, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_USBD, + }, { + .name = "timers", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_PWMT, + }, { + .name = "uart", + .id = 0, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART0, + }, { + .name = "uart", + .id = 1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART1, + }, { + .name = "uart", + .id = 2, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART2, + }, { + .name = "rtc", + .id = -1, + .parent = &clk_p, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_RTC, + }, { + .name = "watchdog", + .id = -1, + .parent = &clk_p, + .ctrlbit = 0, + }, { + .name = "usb-bus-host", + .id = -1, + .parent = &clk_usb_bus, + }, { + .name = "usb-bus-gadget", + .id = -1, + .parent = &clk_usb_bus, + }, }; -struct clk s3c24xx_clkout1 = { - .name = "clkout1", - .id = -1, - .set_parent = s3c24xx_clkout_setparent, -}; - -struct clk s3c24xx_uclk = { - .name = "uclk", - .id = -1, -}; - -/* initialise the clock system */ - -int s3c24xx_register_clock(struct clk *clk) -{ - clk->owner = THIS_MODULE; - - if (clk->enable == NULL) - clk->enable = clk_null_enable; - - /* add to the list of available clocks */ - - mutex_lock(&clocks_mutex); - list_add(&clk->list, &clocks); - mutex_unlock(&clocks_mutex); - - return 0; -} - -/* initalise all the clocks */ +/* s3c2410_baseclk_add() + * + * Add all the clocks used by the s3c2410 or compatible CPUs + * such as the S3C2440 and S3C2442. + * + * We cannot use a system device as we are needed before any + * of the init-calls that initialise the devices are actually + * done. +*/ -int __init s3c24xx_setup_clocks(unsigned long xtal, - unsigned long fclk, - unsigned long hclk, - unsigned long pclk) +int __init s3c2410_baseclk_add(void) { - printk(KERN_INFO "S3C24XX Clocks, (c) 2004 Simtec Electronics\n"); + unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); + unsigned long clkcon = __raw_readl(S3C2410_CLKCON); + struct clk *clkp; + struct clk *xtal; + int ret; + int ptr; - /* initialise the main system clocks */ + clk_upll.enable = s3c2410_upll_enable; - clk_xtal.rate = xtal; - clk_upll.rate = s3c2410_get_pll(__raw_readl(S3C2410_UPLLCON), xtal); + if (s3c24xx_register_clock(&clk_usb_bus) < 0) + printk(KERN_ERR "failed to register usb bus clock\n"); - clk_mpll.rate = fclk; - clk_h.rate = hclk; - clk_p.rate = pclk; - clk_f.rate = fclk; + /* register clocks from clock array */ - /* assume uart clocks are correctly setup */ + clkp = init_clocks; + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { + /* ensure that we note the clock state */ - /* register our clocks */ + clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; - if (s3c24xx_register_clock(&clk_xtal) < 0) - printk(KERN_ERR "failed to register master xtal\n"); + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + } - if (s3c24xx_register_clock(&clk_mpll) < 0) - printk(KERN_ERR "failed to register mpll clock\n"); + /* We must be careful disabling the clocks we are not intending to + * be using at boot time, as subsytems such as the LCD which do + * their own DMA requests to the bus can cause the system to lockup + * if they where in the middle of requesting bus access. + * + * Disabling the LCD clock if the LCD is active is very dangerous, + * and therefore the bootloader should be careful to not enable + * the LCD clock if it is not needed. + */ + + /* install (and disable) the clocks we do not need immediately */ + + clkp = init_clocks_disable; + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) { + + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } - if (s3c24xx_register_clock(&clk_upll) < 0) - printk(KERN_ERR "failed to register upll clock\n"); + s3c2410_clkcon_enable(clkp, 0); + } - if (s3c24xx_register_clock(&clk_f) < 0) - printk(KERN_ERR "failed to register cpu fclk\n"); + /* show the clock-slow value */ - if (s3c24xx_register_clock(&clk_h) < 0) - printk(KERN_ERR "failed to register cpu hclk\n"); + xtal = clk_get(NULL, "xtal"); - if (s3c24xx_register_clock(&clk_p) < 0) - printk(KERN_ERR "failed to register cpu pclk\n"); + printk("CLOCK: Slow mode (%ld.%ld MHz), %s, MPLL %s, UPLL %s\n", + print_mhz(clk_get_rate(xtal) / + ( 2 * S3C2410_CLKSLOW_GET_SLOWVAL(clkslow))), + (clkslow & S3C2410_CLKSLOW_SLOW) ? "slow" : "fast", + (clkslow & S3C2410_CLKSLOW_MPLL_OFF) ? "off" : "on", + (clkslow & S3C2410_CLKSLOW_UCLK_OFF) ? "off" : "on"); return 0; } diff --git a/arch/arm/mach-s3c2410/clock.h b/arch/arm/mach-s3c2410/clock.h deleted file mode 100644 index 7f0ea03e1d49..000000000000 --- a/arch/arm/mach-s3c2410/clock.h +++ /dev/null @@ -1,63 +0,0 @@ -/* - * linux/arch/arm/mach-s3c2410/clock.h - * - * Copyright (c) 2004-2005 Simtec Electronics - * http://www.simtec.co.uk/products/SWLINUX/ - * Written by Ben Dooks, - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -struct clk { - struct list_head list; - struct module *owner; - struct clk *parent; - const char *name; - int id; - int usage; - unsigned long rate; - unsigned long ctrlbit; - - int (*enable)(struct clk *, int enable); - int (*set_rate)(struct clk *c, unsigned long rate); - unsigned long (*get_rate)(struct clk *c); - unsigned long (*round_rate)(struct clk *c, unsigned long rate); - int (*set_parent)(struct clk *c, struct clk *parent); -}; - -/* other clocks which may be registered by board support */ - -extern struct clk s3c24xx_dclk0; -extern struct clk s3c24xx_dclk1; -extern struct clk s3c24xx_clkout0; -extern struct clk s3c24xx_clkout1; -extern struct clk s3c24xx_uclk; - -extern struct clk clk_usb_bus; - -/* core clock support */ - -extern struct clk clk_f; -extern struct clk clk_h; -extern struct clk clk_p; -extern struct clk clk_mpll; -extern struct clk clk_upll; -extern struct clk clk_xtal; - -/* exports for arch/arm/mach-s3c2410 - * - * Please DO NOT use these outside of arch/arm/mach-s3c2410 -*/ - -extern struct mutex clocks_mutex; - -extern int s3c2410_clkcon_enable(struct clk *clk, int enable); - -extern int s3c24xx_register_clock(struct clk *clk); - -extern int s3c24xx_setup_clocks(unsigned long xtal, - unsigned long fclk, - unsigned long hclk, - unsigned long pclk); diff --git a/arch/arm/mach-s3c2410/common-smdk.c b/arch/arm/mach-s3c2410/common-smdk.c deleted file mode 100644 index a40eaa656177..000000000000 --- a/arch/arm/mach-s3c2410/common-smdk.c +++ /dev/null @@ -1,200 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/common-smdk.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * Common code for SMDK2410 and SMDK2440 boards - * - * http://www.fluff.org/ben/smdk2440/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include - -#include "common-smdk.h" -#include "devs.h" -#include "pm.h" - -/* LED devices */ - -static struct s3c24xx_led_platdata smdk_pdata_led4 = { - .gpio = S3C2410_GPF4, - .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, - .name = "led4", - .def_trigger = "timer", -}; - -static struct s3c24xx_led_platdata smdk_pdata_led5 = { - .gpio = S3C2410_GPF5, - .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, - .name = "led5", - .def_trigger = "nand-disk", -}; - -static struct s3c24xx_led_platdata smdk_pdata_led6 = { - .gpio = S3C2410_GPF6, - .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, - .name = "led6", -}; - -static struct s3c24xx_led_platdata smdk_pdata_led7 = { - .gpio = S3C2410_GPF7, - .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, - .name = "led7", -}; - -static struct platform_device smdk_led4 = { - .name = "s3c24xx_led", - .id = 0, - .dev = { - .platform_data = &smdk_pdata_led4, - }, -}; - -static struct platform_device smdk_led5 = { - .name = "s3c24xx_led", - .id = 1, - .dev = { - .platform_data = &smdk_pdata_led5, - }, -}; - -static struct platform_device smdk_led6 = { - .name = "s3c24xx_led", - .id = 2, - .dev = { - .platform_data = &smdk_pdata_led6, - }, -}; - -static struct platform_device smdk_led7 = { - .name = "s3c24xx_led", - .id = 3, - .dev = { - .platform_data = &smdk_pdata_led7, - }, -}; - -/* NAND parititon from 2.4.18-swl5 */ - -static struct mtd_partition smdk_default_nand_part[] = { - [0] = { - .name = "Boot Agent", - .size = SZ_16K, - .offset = 0, - }, - [1] = { - .name = "S3C2410 flash partition 1", - .offset = 0, - .size = SZ_2M, - }, - [2] = { - .name = "S3C2410 flash partition 2", - .offset = SZ_4M, - .size = SZ_4M, - }, - [3] = { - .name = "S3C2410 flash partition 3", - .offset = SZ_8M, - .size = SZ_2M, - }, - [4] = { - .name = "S3C2410 flash partition 4", - .offset = SZ_1M * 10, - .size = SZ_4M, - }, - [5] = { - .name = "S3C2410 flash partition 5", - .offset = SZ_1M * 14, - .size = SZ_1M * 10, - }, - [6] = { - .name = "S3C2410 flash partition 6", - .offset = SZ_1M * 24, - .size = SZ_1M * 24, - }, - [7] = { - .name = "S3C2410 flash partition 7", - .offset = SZ_1M * 48, - .size = SZ_16M, - } -}; - -static struct s3c2410_nand_set smdk_nand_sets[] = { - [0] = { - .name = "NAND", - .nr_chips = 1, - .nr_partitions = ARRAY_SIZE(smdk_default_nand_part), - .partitions = smdk_default_nand_part, - }, -}; - -/* choose a set of timings which should suit most 512Mbit - * chips and beyond. -*/ - -static struct s3c2410_platform_nand smdk_nand_info = { - .tacls = 20, - .twrph0 = 60, - .twrph1 = 20, - .nr_sets = ARRAY_SIZE(smdk_nand_sets), - .sets = smdk_nand_sets, -}; - -/* devices we initialise */ - -static struct platform_device __initdata *smdk_devs[] = { - &s3c_device_nand, - &smdk_led4, - &smdk_led5, - &smdk_led6, - &smdk_led7, -}; - -void __init smdk_machine_init(void) -{ - /* Configure the LEDs (even if we have no LED support)*/ - - s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP); - s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP); - s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP); - s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP); - - s3c2410_gpio_setpin(S3C2410_GPF4, 1); - s3c2410_gpio_setpin(S3C2410_GPF5, 1); - s3c2410_gpio_setpin(S3C2410_GPF6, 1); - s3c2410_gpio_setpin(S3C2410_GPF7, 1); - - s3c_device_nand.dev.platform_data = &smdk_nand_info; - - platform_add_devices(smdk_devs, ARRAY_SIZE(smdk_devs)); - - s3c2410_pm_init(); -} diff --git a/arch/arm/mach-s3c2410/common-smdk.h b/arch/arm/mach-s3c2410/common-smdk.h deleted file mode 100644 index 0e3a3be330a3..000000000000 --- a/arch/arm/mach-s3c2410/common-smdk.h +++ /dev/null @@ -1,15 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/common-smdk.h - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * Common code for SMDK2410 and SMDK2440 boards - * - * http://www.fluff.org/ben/smdk2440/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -extern void smdk_machine_init(void); diff --git a/arch/arm/mach-s3c2410/cpu.c b/arch/arm/mach-s3c2410/cpu.c deleted file mode 100644 index ae1f5bb63f7a..000000000000 --- a/arch/arm/mach-s3c2410/cpu.c +++ /dev/null @@ -1,357 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/cpu.c - * - * Copyright (c) 2004-2005 Simtec Electronics - * http://www.simtec.co.uk/products/SWLINUX/ - * Ben Dooks - * - * S3C24XX CPU Support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include - -#include -#include - -#include "cpu.h" -#include "devs.h" -#include "clock.h" -#include "s3c2400.h" -#include "s3c2410.h" -#include "s3c2412.h" -#include "s3c244x.h" -#include "s3c2440.h" -#include "s3c2442.h" - -struct cpu_table { - unsigned long idcode; - unsigned long idmask; - void (*map_io)(struct map_desc *mach_desc, int size); - void (*init_uarts)(struct s3c2410_uartcfg *cfg, int no); - void (*init_clocks)(int xtal); - int (*init)(void); - const char *name; -}; - -/* table of supported CPUs */ - -static const char name_s3c2400[] = "S3C2400"; -static const char name_s3c2410[] = "S3C2410"; -static const char name_s3c2412[] = "S3C2412"; -static const char name_s3c2440[] = "S3C2440"; -static const char name_s3c2442[] = "S3C2442"; -static const char name_s3c2410a[] = "S3C2410A"; -static const char name_s3c2440a[] = "S3C2440A"; - -static struct cpu_table cpu_ids[] __initdata = { - { - .idcode = 0x32410000, - .idmask = 0xffffffff, - .map_io = s3c2410_map_io, - .init_clocks = s3c2410_init_clocks, - .init_uarts = s3c2410_init_uarts, - .init = s3c2410_init, - .name = name_s3c2410 - }, - { - .idcode = 0x32410002, - .idmask = 0xffffffff, - .map_io = s3c2410_map_io, - .init_clocks = s3c2410_init_clocks, - .init_uarts = s3c2410_init_uarts, - .init = s3c2410_init, - .name = name_s3c2410a - }, - { - .idcode = 0x32440000, - .idmask = 0xffffffff, - .map_io = s3c244x_map_io, - .init_clocks = s3c244x_init_clocks, - .init_uarts = s3c244x_init_uarts, - .init = s3c2440_init, - .name = name_s3c2440 - }, - { - .idcode = 0x32440001, - .idmask = 0xffffffff, - .map_io = s3c244x_map_io, - .init_clocks = s3c244x_init_clocks, - .init_uarts = s3c244x_init_uarts, - .init = s3c2440_init, - .name = name_s3c2440a - }, - { - .idcode = 0x32440aaa, - .idmask = 0xffffffff, - .map_io = s3c244x_map_io, - .init_clocks = s3c244x_init_clocks, - .init_uarts = s3c244x_init_uarts, - .init = s3c2442_init, - .name = name_s3c2442 - }, - { - .idcode = 0x32412001, - .idmask = 0xffffffff, - .map_io = s3c2412_map_io, - .init_clocks = s3c2412_init_clocks, - .init_uarts = s3c2412_init_uarts, - .init = s3c2412_init, - .name = name_s3c2412, - }, - { /* a newer version of the s3c2412 */ - .idcode = 0x32412003, - .idmask = 0xffffffff, - .map_io = s3c2412_map_io, - .init_clocks = s3c2412_init_clocks, - .init_uarts = s3c2412_init_uarts, - .init = s3c2412_init, - .name = name_s3c2412, - }, - { - .idcode = 0x0, /* S3C2400 doesn't have an idcode */ - .idmask = 0xffffffff, - .map_io = s3c2400_map_io, - .init_clocks = s3c2400_init_clocks, - .init_uarts = s3c2400_init_uarts, - .init = s3c2400_init, - .name = name_s3c2400 - }, -}; - -/* minimal IO mapping */ - -static struct map_desc s3c_iodesc[] __initdata = { - IODESC_ENT(GPIO), - IODESC_ENT(IRQ), - IODESC_ENT(MEMCTRL), - IODESC_ENT(UART) -}; - - -static struct cpu_table * -s3c_lookup_cpu(unsigned long idcode) -{ - struct cpu_table *tab; - int count; - - tab = cpu_ids; - for (count = 0; count < ARRAY_SIZE(cpu_ids); count++, tab++) { - if ((idcode & tab->idmask) == tab->idcode) - return tab; - } - - return NULL; -} - -/* board information */ - -static struct s3c24xx_board *board; - -void s3c24xx_set_board(struct s3c24xx_board *b) -{ - int i; - - board = b; - - if (b->clocks_count != 0) { - struct clk **ptr = b->clocks; - - for (i = b->clocks_count; i > 0; i--, ptr++) - s3c24xx_register_clock(*ptr); - } -} - -/* cpu information */ - -static struct cpu_table *cpu; - -static unsigned long s3c24xx_read_idcode_v5(void) -{ -#if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413) - return __raw_readl(S3C2412_GSTATUS1); -#else - return 1UL; /* don't look like an 2400 */ -#endif -} - -static unsigned long s3c24xx_read_idcode_v4(void) -{ -#ifndef CONFIG_CPU_S3C2400 - return __raw_readl(S3C2410_GSTATUS1); -#else - return 0UL; -#endif -} - -void __init s3c24xx_init_io(struct map_desc *mach_desc, int size) -{ - unsigned long idcode = 0x0; - - /* initialise the io descriptors we need for initialisation */ - iotable_init(s3c_iodesc, ARRAY_SIZE(s3c_iodesc)); - - if (cpu_architecture() >= CPU_ARCH_ARMv5) { - idcode = s3c24xx_read_idcode_v5(); - } else { - idcode = s3c24xx_read_idcode_v4(); - } - - cpu = s3c_lookup_cpu(idcode); - - if (cpu == NULL) { - printk(KERN_ERR "Unknown CPU type 0x%08lx\n", idcode); - panic("Unknown S3C24XX CPU"); - } - - printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode); - - if (cpu->map_io == NULL || cpu->init == NULL) { - printk(KERN_ERR "CPU %s support not enabled\n", cpu->name); - panic("Unsupported S3C24XX CPU"); - } - - (cpu->map_io)(mach_desc, size); -} - -/* s3c24xx_init_clocks - * - * Initialise the clock subsystem and associated information from the - * given master crystal value. - * - * xtal = 0 -> use default PLL crystal value (normally 12MHz) - * != 0 -> PLL crystal value in Hz -*/ - -void __init s3c24xx_init_clocks(int xtal) -{ - if (xtal == 0) - xtal = 12*1000*1000; - - if (cpu == NULL) - panic("s3c24xx_init_clocks: no cpu setup?\n"); - - if (cpu->init_clocks == NULL) - panic("s3c24xx_init_clocks: cpu has no clock init\n"); - else - (cpu->init_clocks)(xtal); -} - -/* uart management */ - -static int nr_uarts __initdata = 0; - -static struct s3c2410_uartcfg uart_cfgs[3]; - -/* s3c24xx_init_uartdevs - * - * copy the specified platform data and configuration into our central - * set of devices, before the data is thrown away after the init process. - * - * This also fills in the array passed to the serial driver for the - * early initialisation of the console. -*/ - -void __init s3c24xx_init_uartdevs(char *name, - struct s3c24xx_uart_resources *res, - struct s3c2410_uartcfg *cfg, int no) -{ - struct platform_device *platdev; - struct s3c2410_uartcfg *cfgptr = uart_cfgs; - struct s3c24xx_uart_resources *resp; - int uart; - - memcpy(cfgptr, cfg, sizeof(struct s3c2410_uartcfg) * no); - - for (uart = 0; uart < no; uart++, cfg++, cfgptr++) { - platdev = s3c24xx_uart_src[cfgptr->hwport]; - - resp = res + cfgptr->hwport; - - s3c24xx_uart_devs[uart] = platdev; - - platdev->name = name; - platdev->resource = resp->resources; - platdev->num_resources = resp->nr_resources; - - platdev->dev.platform_data = cfgptr; - } - - nr_uarts = no; -} - -void __init s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no) -{ - if (cpu == NULL) - return; - - if (cpu->init_uarts == NULL) { - printk(KERN_ERR "s3c24xx_init_uarts: cpu has no uart init\n"); - } else - (cpu->init_uarts)(cfg, no); -} - -static int __init s3c_arch_init(void) -{ - int ret; - - // do the correct init for cpu - - if (cpu == NULL) - panic("s3c_arch_init: NULL cpu\n"); - - ret = (cpu->init)(); - if (ret != 0) - return ret; - - ret = platform_add_devices(s3c24xx_uart_devs, nr_uarts); - if (ret != 0) - return ret; - - if (board != NULL) { - struct platform_device **ptr = board->devices; - int i; - - for (i = 0; i < board->devices_count; i++, ptr++) { - ret = platform_device_register(*ptr); - - if (ret) { - printk(KERN_ERR "s3c24xx: failed to add board device %s (%d) @%p\n", (*ptr)->name, ret, *ptr); - } - } - - /* mask any error, we may not need all these board - * devices */ - ret = 0; - } - - return ret; -} - -arch_initcall(s3c_arch_init); diff --git a/arch/arm/mach-s3c2410/cpu.h b/arch/arm/mach-s3c2410/cpu.h deleted file mode 100644 index be42e4032a6d..000000000000 --- a/arch/arm/mach-s3c2410/cpu.h +++ /dev/null @@ -1,69 +0,0 @@ -/* arch/arm/mach-s3c2410/cpu.h - * - * Copyright (c) 2004-2005 Simtec Electronics - * Ben Dooks - * - * Header file for S3C24XX CPU support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -/* todo - fix when rmk changes iodescs to use `void __iomem *` */ - -#define IODESC_ENT(x) { (unsigned long)S3C24XX_VA_##x, __phys_to_pfn(S3C24XX_PA_##x), S3C24XX_SZ_##x, MT_DEVICE } - -#ifndef MHZ -#define MHZ (1000*1000) -#endif - -#define print_mhz(m) ((m) / MHZ), ((m / 1000) % 1000) - -/* forward declaration */ -struct s3c24xx_uart_resources; -struct platform_device; -struct s3c2410_uartcfg; -struct map_desc; - -/* core initialisation functions */ - -extern void s3c24xx_init_irq(void); - -extern void s3c24xx_init_io(struct map_desc *mach_desc, int size); - -extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no); - -extern void s3c24xx_init_clocks(int xtal); - -extern void s3c24xx_init_uartdevs(char *name, - struct s3c24xx_uart_resources *res, - struct s3c2410_uartcfg *cfg, int no); - -/* the board structure is used at first initialsation time - * to get info such as the devices to register for this - * board. This is done because platfrom_add_devices() cannot - * be called from the map_io entry. -*/ - -struct s3c24xx_board { - struct platform_device **devices; - unsigned int devices_count; - - struct clk **clocks; - unsigned int clocks_count; -}; - -extern void s3c24xx_set_board(struct s3c24xx_board *board); - -/* timer for 2410/2440 */ - -struct sys_timer; -extern struct sys_timer s3c24xx_timer; - -/* system device classes */ - -extern struct sysdev_class s3c2410_sysclass; -extern struct sysdev_class s3c2412_sysclass; -extern struct sysdev_class s3c2440_sysclass; -extern struct sysdev_class s3c2442_sysclass; diff --git a/arch/arm/mach-s3c2410/devs.c b/arch/arm/mach-s3c2410/devs.c deleted file mode 100644 index faccde2092d2..000000000000 --- a/arch/arm/mach-s3c2410/devs.c +++ /dev/null @@ -1,585 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/devs.c - * - * Copyright (c) 2004 Simtec Electronics - * Ben Dooks - * - * Base S3C24XX platform device definitions - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -#include - -#include "devs.h" -#include "cpu.h" - -/* Serial port registrations */ - -static struct resource s3c2410_uart0_resource[] = { - [0] = { - .start = S3C2410_PA_UART0, - .end = S3C2410_PA_UART0 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX0, - .end = IRQ_S3CUART_ERR0, - .flags = IORESOURCE_IRQ, - } -}; - -static struct resource s3c2410_uart1_resource[] = { - [0] = { - .start = S3C2410_PA_UART1, - .end = S3C2410_PA_UART1 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX1, - .end = IRQ_S3CUART_ERR1, - .flags = IORESOURCE_IRQ, - } -}; - -static struct resource s3c2410_uart2_resource[] = { - [0] = { - .start = S3C2410_PA_UART2, - .end = S3C2410_PA_UART2 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX2, - .end = IRQ_S3CUART_ERR2, - .flags = IORESOURCE_IRQ, - } -}; - -struct s3c24xx_uart_resources s3c2410_uart_resources[] __initdata = { - [0] = { - .resources = s3c2410_uart0_resource, - .nr_resources = ARRAY_SIZE(s3c2410_uart0_resource), - }, - [1] = { - .resources = s3c2410_uart1_resource, - .nr_resources = ARRAY_SIZE(s3c2410_uart1_resource), - }, - [2] = { - .resources = s3c2410_uart2_resource, - .nr_resources = ARRAY_SIZE(s3c2410_uart2_resource), - }, -}; - -/* yart devices */ - -static struct platform_device s3c24xx_uart_device0 = { - .id = 0, -}; - -static struct platform_device s3c24xx_uart_device1 = { - .id = 1, -}; - -static struct platform_device s3c24xx_uart_device2 = { - .id = 2, -}; - -struct platform_device *s3c24xx_uart_src[3] = { - &s3c24xx_uart_device0, - &s3c24xx_uart_device1, - &s3c24xx_uart_device2, -}; - -struct platform_device *s3c24xx_uart_devs[3] = { -}; - -/* USB Host Controller */ - -static struct resource s3c_usb_resource[] = { - [0] = { - .start = S3C24XX_PA_USBHOST, - .end = S3C24XX_PA_USBHOST + S3C24XX_SZ_USBHOST - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_USBH, - .end = IRQ_USBH, - .flags = IORESOURCE_IRQ, - } -}; - -static u64 s3c_device_usb_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_usb = { - .name = "s3c2410-ohci", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_usb_resource), - .resource = s3c_usb_resource, - .dev = { - .dma_mask = &s3c_device_usb_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_usb); - -/* LCD Controller */ - -static struct resource s3c_lcd_resource[] = { - [0] = { - .start = S3C24XX_PA_LCD, - .end = S3C24XX_PA_LCD + S3C24XX_SZ_LCD - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_LCD, - .end = IRQ_LCD, - .flags = IORESOURCE_IRQ, - } - -}; - -static u64 s3c_device_lcd_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_lcd = { - .name = "s3c2410-lcd", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_lcd_resource), - .resource = s3c_lcd_resource, - .dev = { - .dma_mask = &s3c_device_lcd_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_lcd); - -void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *pd) -{ - struct s3c2410fb_mach_info *npd; - - npd = kmalloc(sizeof(*npd), GFP_KERNEL); - if (npd) { - memcpy(npd, pd, sizeof(*npd)); - s3c_device_lcd.dev.platform_data = npd; - } else { - printk(KERN_ERR "no memory for LCD platform data\n"); - } -} - -/* NAND Controller */ - -static struct resource s3c_nand_resource[] = { - [0] = { - .start = S3C2410_PA_NAND, - .end = S3C2410_PA_NAND + S3C24XX_SZ_NAND - 1, - .flags = IORESOURCE_MEM, - } -}; - -struct platform_device s3c_device_nand = { - .name = "s3c2410-nand", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_nand_resource), - .resource = s3c_nand_resource, -}; - -EXPORT_SYMBOL(s3c_device_nand); - -/* USB Device (Gadget)*/ - -static struct resource s3c_usbgadget_resource[] = { - [0] = { - .start = S3C24XX_PA_USBDEV, - .end = S3C24XX_PA_USBDEV + S3C24XX_SZ_USBDEV - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_USBD, - .end = IRQ_USBD, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_usbgadget = { - .name = "s3c2410-usbgadget", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_usbgadget_resource), - .resource = s3c_usbgadget_resource, -}; - -EXPORT_SYMBOL(s3c_device_usbgadget); - -/* Watchdog */ - -static struct resource s3c_wdt_resource[] = { - [0] = { - .start = S3C24XX_PA_WATCHDOG, - .end = S3C24XX_PA_WATCHDOG + S3C24XX_SZ_WATCHDOG - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_WDT, - .end = IRQ_WDT, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_wdt = { - .name = "s3c2410-wdt", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_wdt_resource), - .resource = s3c_wdt_resource, -}; - -EXPORT_SYMBOL(s3c_device_wdt); - -/* I2C */ - -static struct resource s3c_i2c_resource[] = { - [0] = { - .start = S3C24XX_PA_IIC, - .end = S3C24XX_PA_IIC + S3C24XX_SZ_IIC - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_IIC, - .end = IRQ_IIC, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_i2c = { - .name = "s3c2410-i2c", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_i2c_resource), - .resource = s3c_i2c_resource, -}; - -EXPORT_SYMBOL(s3c_device_i2c); - -/* IIS */ - -static struct resource s3c_iis_resource[] = { - [0] = { - .start = S3C24XX_PA_IIS, - .end = S3C24XX_PA_IIS + S3C24XX_SZ_IIS -1, - .flags = IORESOURCE_MEM, - } -}; - -static u64 s3c_device_iis_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_iis = { - .name = "s3c2410-iis", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_iis_resource), - .resource = s3c_iis_resource, - .dev = { - .dma_mask = &s3c_device_iis_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_iis); - -/* RTC */ - -static struct resource s3c_rtc_resource[] = { - [0] = { - .start = S3C24XX_PA_RTC, - .end = S3C24XX_PA_RTC + 0xff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_RTC, - .end = IRQ_RTC, - .flags = IORESOURCE_IRQ, - }, - [2] = { - .start = IRQ_TICK, - .end = IRQ_TICK, - .flags = IORESOURCE_IRQ - } -}; - -struct platform_device s3c_device_rtc = { - .name = "s3c2410-rtc", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_rtc_resource), - .resource = s3c_rtc_resource, -}; - -EXPORT_SYMBOL(s3c_device_rtc); - -/* ADC */ - -static struct resource s3c_adc_resource[] = { - [0] = { - .start = S3C24XX_PA_ADC, - .end = S3C24XX_PA_ADC + S3C24XX_SZ_ADC - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TC, - .end = IRQ_TC, - .flags = IORESOURCE_IRQ, - }, - [2] = { - .start = IRQ_ADC, - .end = IRQ_ADC, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_adc = { - .name = "s3c2410-adc", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_adc_resource), - .resource = s3c_adc_resource, -}; - -/* SDI */ - -static struct resource s3c_sdi_resource[] = { - [0] = { - .start = S3C2410_PA_SDI, - .end = S3C2410_PA_SDI + S3C24XX_SZ_SDI - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_SDI, - .end = IRQ_SDI, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_sdi = { - .name = "s3c2410-sdi", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_sdi_resource), - .resource = s3c_sdi_resource, -}; - -EXPORT_SYMBOL(s3c_device_sdi); - -/* SPI (0) */ - -static struct resource s3c_spi0_resource[] = { - [0] = { - .start = S3C24XX_PA_SPI, - .end = S3C24XX_PA_SPI + 0x1f, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_SPI0, - .end = IRQ_SPI0, - .flags = IORESOURCE_IRQ, - } - -}; - -static u64 s3c_device_spi0_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_spi0 = { - .name = "s3c2410-spi", - .id = 0, - .num_resources = ARRAY_SIZE(s3c_spi0_resource), - .resource = s3c_spi0_resource, - .dev = { - .dma_mask = &s3c_device_spi0_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_spi0); - -/* SPI (1) */ - -static struct resource s3c_spi1_resource[] = { - [0] = { - .start = S3C24XX_PA_SPI + 0x20, - .end = S3C24XX_PA_SPI + 0x20 + 0x1f, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_SPI1, - .end = IRQ_SPI1, - .flags = IORESOURCE_IRQ, - } - -}; - -static u64 s3c_device_spi1_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_spi1 = { - .name = "s3c2410-spi", - .id = 1, - .num_resources = ARRAY_SIZE(s3c_spi1_resource), - .resource = s3c_spi1_resource, - .dev = { - .dma_mask = &s3c_device_spi1_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_spi1); - -/* pwm timer blocks */ - -static struct resource s3c_timer0_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x0C, - .end = S3C24XX_PA_TIMER + 0x0C + 0xB, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER0, - .end = IRQ_TIMER0, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer0 = { - .name = "s3c2410-timer", - .id = 0, - .num_resources = ARRAY_SIZE(s3c_timer0_resource), - .resource = s3c_timer0_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer0); - -/* timer 1 */ - -static struct resource s3c_timer1_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x18, - .end = S3C24XX_PA_TIMER + 0x23, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER1, - .end = IRQ_TIMER1, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer1 = { - .name = "s3c2410-timer", - .id = 1, - .num_resources = ARRAY_SIZE(s3c_timer1_resource), - .resource = s3c_timer1_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer1); - -/* timer 2 */ - -static struct resource s3c_timer2_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x24, - .end = S3C24XX_PA_TIMER + 0x2F, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER2, - .end = IRQ_TIMER2, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer2 = { - .name = "s3c2410-timer", - .id = 2, - .num_resources = ARRAY_SIZE(s3c_timer2_resource), - .resource = s3c_timer2_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer2); - -/* timer 3 */ - -static struct resource s3c_timer3_resource[] = { - [0] = { - .start = S3C24XX_PA_TIMER + 0x30, - .end = S3C24XX_PA_TIMER + 0x3B, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TIMER3, - .end = IRQ_TIMER3, - .flags = IORESOURCE_IRQ, - } - -}; - -struct platform_device s3c_device_timer3 = { - .name = "s3c2410-timer", - .id = 3, - .num_resources = ARRAY_SIZE(s3c_timer3_resource), - .resource = s3c_timer3_resource, -}; - -EXPORT_SYMBOL(s3c_device_timer3); - -#ifdef CONFIG_CPU_S3C2440 - -/* Camif Controller */ - -static struct resource s3c_camif_resource[] = { - [0] = { - .start = S3C2440_PA_CAMIF, - .end = S3C2440_PA_CAMIF + S3C2440_SZ_CAMIF - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_CAM, - .end = IRQ_CAM, - .flags = IORESOURCE_IRQ, - } - -}; - -static u64 s3c_device_camif_dmamask = 0xffffffffUL; - -struct platform_device s3c_device_camif = { - .name = "s3c2440-camif", - .id = -1, - .num_resources = ARRAY_SIZE(s3c_camif_resource), - .resource = s3c_camif_resource, - .dev = { - .dma_mask = &s3c_device_camif_dmamask, - .coherent_dma_mask = 0xffffffffUL - } -}; - -EXPORT_SYMBOL(s3c_device_camif); - -#endif // CONFIG_CPU_S32440 diff --git a/arch/arm/mach-s3c2410/devs.h b/arch/arm/mach-s3c2410/devs.h deleted file mode 100644 index 14fb0bade716..000000000000 --- a/arch/arm/mach-s3c2410/devs.h +++ /dev/null @@ -1,51 +0,0 @@ -/* arch/arm/mach-s3c2410/devs.h - * - * Copyright (c) 2004 Simtec Electronics - * Ben Dooks - * - * Header file for s3c2410 standard platform devices - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ -#include - -struct s3c24xx_uart_resources { - struct resource *resources; - unsigned long nr_resources; -}; - -extern struct s3c24xx_uart_resources s3c2410_uart_resources[]; - -extern struct platform_device *s3c24xx_uart_devs[]; -extern struct platform_device *s3c24xx_uart_src[]; - -extern struct platform_device s3c_device_usb; -extern struct platform_device s3c_device_lcd; -extern struct platform_device s3c_device_wdt; -extern struct platform_device s3c_device_i2c; -extern struct platform_device s3c_device_iis; -extern struct platform_device s3c_device_rtc; -extern struct platform_device s3c_device_adc; -extern struct platform_device s3c_device_sdi; - -extern struct platform_device s3c_device_spi0; -extern struct platform_device s3c_device_spi1; - -extern struct platform_device s3c_device_nand; - -extern struct platform_device s3c_device_timer0; -extern struct platform_device s3c_device_timer1; -extern struct platform_device s3c_device_timer2; -extern struct platform_device s3c_device_timer3; - -extern struct platform_device s3c_device_usbgadget; - -/* s3c2440 specific devices */ - -#ifdef CONFIG_CPU_S3C2440 - -extern struct platform_device s3c_device_camif; - -#endif diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c index fa860e716b4f..22c613600caa 100644 --- a/arch/arm/mach-s3c2410/dma.c +++ b/arch/arm/mach-s3c2410/dma.c @@ -1,9 +1,9 @@ /* linux/arch/arm/mach-s3c2410/dma.c * - * Copyright (c) 2003-2005,2006 Simtec Electronics + * Copyright (c) 2006 Simtec Electronics * Ben Dooks * - * S3C2410 DMA core + * S3C2410 DMA selection * * http://armlinux.simtec.co.uk/ * @@ -12,1430 +12,150 @@ * published by the Free Software Foundation. */ - -#ifdef CONFIG_S3C2410_DMA_DEBUG -#define DEBUG -#endif - -#include +#include #include -#include -#include -#include #include -#include -#include -#include +#include -#include -#include -#include -#include #include - -#include -#include - -#include "dma.h" - -/* io map for dma */ -static void __iomem *dma_base; -static struct kmem_cache *dma_kmem; - -struct s3c24xx_dma_selection dma_sel; - -/* dma channel state information */ -struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; - -/* debugging functions */ - -#define BUF_MAGIC (0xcafebabe) - -#define dmawarn(fmt...) printk(KERN_DEBUG fmt) - -#define dma_regaddr(chan, reg) ((chan)->regs + (reg)) - -#if 1 -#define dma_wrreg(chan, reg, val) writel((val), (chan)->regs + (reg)) -#else -static inline void -dma_wrreg(struct s3c2410_dma_chan *chan, int reg, unsigned long val) -{ - pr_debug("writing %08x to register %08x\n",(unsigned int)val,reg); - writel(val, dma_regaddr(chan, reg)); -} -#endif - -#define dma_rdreg(chan, reg) readl((chan)->regs + (reg)) - -/* captured register state for debug */ - -struct s3c2410_dma_regstate { - unsigned long dcsrc; - unsigned long disrc; - unsigned long dstat; - unsigned long dcon; - unsigned long dmsktrig; +#include +#include + +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +static struct s3c24xx_dma_map __initdata s3c2410_dma_mappings[] = { + [DMACH_XD0] = { + .name = "xdreq0", + .channels[0] = S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID, + }, + [DMACH_XD1] = { + .name = "xdreq1", + .channels[1] = S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID, + }, + [DMACH_SDI] = { + .name = "sdi", + .channels[0] = S3C2410_DCON_CH0_SDI | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_SDI | DMA_CH_VALID, + .channels[3] = S3C2410_DCON_CH3_SDI | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_SPI0] = { + .name = "spi0", + .channels[1] = S3C2410_DCON_CH1_SPI | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, + }, + [DMACH_SPI1] = { + .name = "spi1", + .channels[3] = S3C2410_DCON_CH3_SPI | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, + }, + [DMACH_UART0] = { + .name = "uart0", + .channels[0] = S3C2410_DCON_CH0_UART0 | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, + }, + [DMACH_UART1] = { + .name = "uart1", + .channels[1] = S3C2410_DCON_CH1_UART1 | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, + }, + [DMACH_UART2] = { + .name = "uart2", + .channels[3] = S3C2410_DCON_CH3_UART2 | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, + }, + [DMACH_TIMER] = { + .name = "timer", + .channels[0] = S3C2410_DCON_CH0_TIMER | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_TIMER | DMA_CH_VALID, + .channels[3] = S3C2410_DCON_CH3_TIMER | DMA_CH_VALID, + }, + [DMACH_I2S_IN] = { + .name = "i2s-sdi", + .channels[1] = S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID, + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_I2S_OUT] = { + .name = "i2s-sdo", + .channels[2] = S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_USB_EP1] = { + .name = "usb-ep1", + .channels[0] = S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID, + }, + [DMACH_USB_EP2] = { + .name = "usb-ep2", + .channels[1] = S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID, + }, + [DMACH_USB_EP3] = { + .name = "usb-ep3", + .channels[2] = S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID, + }, + [DMACH_USB_EP4] = { + .name = "usb-ep4", + .channels[3] =S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID, + }, }; -#ifdef CONFIG_S3C2410_DMA_DEBUG - -/* dmadbg_showregs - * - * simple debug routine to print the current state of the dma registers -*/ - -static void -dmadbg_capture(struct s3c2410_dma_chan *chan, struct s3c2410_dma_regstate *regs) -{ - regs->dcsrc = dma_rdreg(chan, S3C2410_DMA_DCSRC); - regs->disrc = dma_rdreg(chan, S3C2410_DMA_DISRC); - regs->dstat = dma_rdreg(chan, S3C2410_DMA_DSTAT); - regs->dcon = dma_rdreg(chan, S3C2410_DMA_DCON); - regs->dmsktrig = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); -} - -static void -dmadbg_dumpregs(const char *fname, int line, struct s3c2410_dma_chan *chan, - struct s3c2410_dma_regstate *regs) -{ - printk(KERN_DEBUG "dma%d: %s:%d: DCSRC=%08lx, DISRC=%08lx, DSTAT=%08lx DMT=%02lx, DCON=%08lx\n", - chan->number, fname, line, - regs->dcsrc, regs->disrc, regs->dstat, regs->dmsktrig, - regs->dcon); -} - -static void -dmadbg_showchan(const char *fname, int line, struct s3c2410_dma_chan *chan) -{ - struct s3c2410_dma_regstate state; - - dmadbg_capture(chan, &state); - - printk(KERN_DEBUG "dma%d: %s:%d: ls=%d, cur=%p, %p %p\n", - chan->number, fname, line, chan->load_state, - chan->curr, chan->next, chan->end); - - dmadbg_dumpregs(fname, line, chan, &state); -} - -static void -dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan) -{ - struct s3c2410_dma_regstate state; - - dmadbg_capture(chan, &state); - dmadbg_dumpregs(fname, line, chan, &state); -} - -#define dbg_showregs(chan) dmadbg_showregs(__FUNCTION__, __LINE__, (chan)) -#define dbg_showchan(chan) dmadbg_showchan(__FUNCTION__, __LINE__, (chan)) -#else -#define dbg_showregs(chan) do { } while(0) -#define dbg_showchan(chan) do { } while(0) -#endif /* CONFIG_S3C2410_DMA_DEBUG */ - -static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX]; - -/* lookup_dma_channel - * - * change the dma channel number given into a real dma channel id -*/ - -static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel) -{ - if (channel & DMACH_LOW_LEVEL) - return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL]; - else - return dma_chan_map[channel]; -} - -/* s3c2410_dma_stats_timeout - * - * Update DMA stats from timeout info -*/ - -static void -s3c2410_dma_stats_timeout(struct s3c2410_dma_stats *stats, int val) +static void s3c2410_dma_select(struct s3c2410_dma_chan *chan, + struct s3c24xx_dma_map *map) { - if (stats == NULL) - return; - - if (val > stats->timeout_longest) - stats->timeout_longest = val; - if (val < stats->timeout_shortest) - stats->timeout_shortest = val; - - stats->timeout_avg += val; + chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID; } -/* s3c2410_dma_waitforload - * - * wait for the DMA engine to load a buffer, and update the state accordingly -*/ - -static int -s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line) -{ - int timeout = chan->load_timeout; - int took; - - if (chan->load_state != S3C2410_DMALOAD_1LOADED) { - printk(KERN_ERR "dma%d: s3c2410_dma_waitforload() called in loadstate %d from line %d\n", chan->number, chan->load_state, line); - return 0; - } - - if (chan->stats != NULL) - chan->stats->loads++; - - while (--timeout > 0) { - if ((dma_rdreg(chan, S3C2410_DMA_DSTAT) << (32-20)) != 0) { - took = chan->load_timeout - timeout; - - s3c2410_dma_stats_timeout(chan->stats, took); - - switch (chan->load_state) { - case S3C2410_DMALOAD_1LOADED: - chan->load_state = S3C2410_DMALOAD_1RUNNING; - break; - - default: - printk(KERN_ERR "dma%d: unknown load_state in s3c2410_dma_waitforload() %d\n", chan->number, chan->load_state); - } - - return 1; - } - } - - if (chan->stats != NULL) { - chan->stats->timeout_failed++; - } - - return 0; -} - - - -/* s3c2410_dma_loadbuffer - * - * load a buffer, and update the channel state -*/ - -static inline int -s3c2410_dma_loadbuffer(struct s3c2410_dma_chan *chan, - struct s3c2410_dma_buf *buf) -{ - unsigned long reload; - - pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n", - buf, (unsigned long)buf->data, buf->size); - - if (buf == NULL) { - dmawarn("buffer is NULL\n"); - return -EINVAL; - } - - /* check the state of the channel before we do anything */ - - if (chan->load_state == S3C2410_DMALOAD_1LOADED) { - dmawarn("load_state is S3C2410_DMALOAD_1LOADED\n"); - } - - if (chan->load_state == S3C2410_DMALOAD_1LOADED_1RUNNING) { - dmawarn("state is S3C2410_DMALOAD_1LOADED_1RUNNING\n"); - } - - /* it would seem sensible if we are the last buffer to not bother - * with the auto-reload bit, so that the DMA engine will not try - * and load another transfer after this one has finished... - */ - if (chan->load_state == S3C2410_DMALOAD_NONE) { - pr_debug("load_state is none, checking for noreload (next=%p)\n", - buf->next); - reload = (buf->next == NULL) ? S3C2410_DCON_NORELOAD : 0; - } else { - //pr_debug("load_state is %d => autoreload\n", chan->load_state); - reload = S3C2410_DCON_AUTORELOAD; - } - - if ((buf->data & 0xf0000000) != 0x30000000) { - dmawarn("dmaload: buffer is %p\n", (void *)buf->data); - } - - writel(buf->data, chan->addr_reg); - - dma_wrreg(chan, S3C2410_DMA_DCON, - chan->dcon | reload | (buf->size/chan->xfer_unit)); - - chan->next = buf->next; - - /* update the state of the channel */ - - switch (chan->load_state) { - case S3C2410_DMALOAD_NONE: - chan->load_state = S3C2410_DMALOAD_1LOADED; - break; - - case S3C2410_DMALOAD_1RUNNING: - chan->load_state = S3C2410_DMALOAD_1LOADED_1RUNNING; - break; - - default: - dmawarn("dmaload: unknown state %d in loadbuffer\n", - chan->load_state); - break; - } - - return 0; -} - -/* s3c2410_dma_call_op - * - * small routine to call the op routine with the given op if it has been - * registered -*/ - -static void -s3c2410_dma_call_op(struct s3c2410_dma_chan *chan, enum s3c2410_chan_op op) -{ - if (chan->op_fn != NULL) { - (chan->op_fn)(chan, op); - } -} - -/* s3c2410_dma_buffdone - * - * small wrapper to check if callback routine needs to be called, and - * if so, call it -*/ - -static inline void -s3c2410_dma_buffdone(struct s3c2410_dma_chan *chan, struct s3c2410_dma_buf *buf, - enum s3c2410_dma_buffresult result) -{ -#if 0 - pr_debug("callback_fn=%p, buf=%p, id=%p, size=%d, result=%d\n", - chan->callback_fn, buf, buf->id, buf->size, result); -#endif - - if (chan->callback_fn != NULL) { - (chan->callback_fn)(chan, buf->id, buf->size, result); - } -} - -/* s3c2410_dma_start - * - * start a dma channel going -*/ - -static int s3c2410_dma_start(struct s3c2410_dma_chan *chan) -{ - unsigned long tmp; - unsigned long flags; - - pr_debug("s3c2410_start_dma: channel=%d\n", chan->number); - - local_irq_save(flags); - - if (chan->state == S3C2410_DMA_RUNNING) { - pr_debug("s3c2410_start_dma: already running (%d)\n", chan->state); - local_irq_restore(flags); - return 0; - } - - chan->state = S3C2410_DMA_RUNNING; - - /* check wether there is anything to load, and if not, see - * if we can find anything to load - */ - - if (chan->load_state == S3C2410_DMALOAD_NONE) { - if (chan->next == NULL) { - printk(KERN_ERR "dma%d: channel has nothing loaded\n", - chan->number); - chan->state = S3C2410_DMA_IDLE; - local_irq_restore(flags); - return -EINVAL; - } - - s3c2410_dma_loadbuffer(chan, chan->next); - } - - dbg_showchan(chan); - - /* enable the channel */ - - if (!chan->irq_enabled) { - enable_irq(chan->irq); - chan->irq_enabled = 1; - } - - /* start the channel going */ - - tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); - tmp &= ~S3C2410_DMASKTRIG_STOP; - tmp |= S3C2410_DMASKTRIG_ON; - dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp); - - pr_debug("dma%d: %08lx to DMASKTRIG\n", chan->number, tmp); - -#if 0 - /* the dma buffer loads should take care of clearing the AUTO - * reloading feature */ - tmp = dma_rdreg(chan, S3C2410_DMA_DCON); - tmp &= ~S3C2410_DCON_NORELOAD; - dma_wrreg(chan, S3C2410_DMA_DCON, tmp); -#endif - - s3c2410_dma_call_op(chan, S3C2410_DMAOP_START); - - dbg_showchan(chan); - - /* if we've only loaded one buffer onto the channel, then chec - * to see if we have another, and if so, try and load it so when - * the first buffer is finished, the new one will be loaded onto - * the channel */ - - if (chan->next != NULL) { - if (chan->load_state == S3C2410_DMALOAD_1LOADED) { - - if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { - pr_debug("%s: buff not yet loaded, no more todo\n", - __FUNCTION__); - } else { - chan->load_state = S3C2410_DMALOAD_1RUNNING; - s3c2410_dma_loadbuffer(chan, chan->next); - } - - } else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) { - s3c2410_dma_loadbuffer(chan, chan->next); - } - } - - - local_irq_restore(flags); - - return 0; -} - -/* s3c2410_dma_canload - * - * work out if we can queue another buffer into the DMA engine -*/ - -static int -s3c2410_dma_canload(struct s3c2410_dma_chan *chan) -{ - if (chan->load_state == S3C2410_DMALOAD_NONE || - chan->load_state == S3C2410_DMALOAD_1RUNNING) - return 1; - - return 0; -} - -/* s3c2410_dma_enqueue - * - * queue an given buffer for dma transfer. - * - * id the device driver's id information for this buffer - * data the physical address of the buffer data - * size the size of the buffer in bytes - * - * If the channel is not running, then the flag S3C2410_DMAF_AUTOSTART - * is checked, and if set, the channel is started. If this flag isn't set, - * then an error will be returned. - * - * It is possible to queue more than one DMA buffer onto a channel at - * once, and the code will deal with the re-loading of the next buffer - * when necessary. -*/ - -int s3c2410_dma_enqueue(unsigned int channel, void *id, - dma_addr_t data, int size) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - struct s3c2410_dma_buf *buf; - unsigned long flags; - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: id=%p, data=%08x, size=%d\n", - __FUNCTION__, id, (unsigned int)data, size); - - buf = kmem_cache_alloc(dma_kmem, GFP_ATOMIC); - if (buf == NULL) { - pr_debug("%s: out of memory (%ld alloc)\n", - __FUNCTION__, (long)sizeof(*buf)); - return -ENOMEM; - } - - //pr_debug("%s: new buffer %p\n", __FUNCTION__, buf); - //dbg_showchan(chan); - - buf->next = NULL; - buf->data = buf->ptr = data; - buf->size = size; - buf->id = id; - buf->magic = BUF_MAGIC; - - local_irq_save(flags); - - if (chan->curr == NULL) { - /* we've got nothing loaded... */ - pr_debug("%s: buffer %p queued onto empty channel\n", - __FUNCTION__, buf); - - chan->curr = buf; - chan->end = buf; - chan->next = NULL; - } else { - pr_debug("dma%d: %s: buffer %p queued onto non-empty channel\n", - chan->number, __FUNCTION__, buf); - - if (chan->end == NULL) - pr_debug("dma%d: %s: %p not empty, and chan->end==NULL?\n", - chan->number, __FUNCTION__, chan); - - chan->end->next = buf; - chan->end = buf; - } - - /* if necessary, update the next buffer field */ - if (chan->next == NULL) - chan->next = buf; - - /* check to see if we can load a buffer */ - if (chan->state == S3C2410_DMA_RUNNING) { - if (chan->load_state == S3C2410_DMALOAD_1LOADED && 1) { - if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { - printk(KERN_ERR "dma%d: loadbuffer:" - "timeout loading buffer\n", - chan->number); - dbg_showchan(chan); - local_irq_restore(flags); - return -EINVAL; - } - } - - while (s3c2410_dma_canload(chan) && chan->next != NULL) { - s3c2410_dma_loadbuffer(chan, chan->next); - } - } else if (chan->state == S3C2410_DMA_IDLE) { - if (chan->flags & S3C2410_DMAF_AUTOSTART) { - s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_START); - } - } - - local_irq_restore(flags); - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_enqueue); - -static inline void -s3c2410_dma_freebuf(struct s3c2410_dma_buf *buf) -{ - int magicok = (buf->magic == BUF_MAGIC); - - buf->magic = -1; - - if (magicok) { - kmem_cache_free(dma_kmem, buf); - } else { - printk("s3c2410_dma_freebuf: buff %p with bad magic\n", buf); - } -} - -/* s3c2410_dma_lastxfer - * - * called when the system is out of buffers, to ensure that the channel - * is prepared for shutdown. -*/ - -static inline void -s3c2410_dma_lastxfer(struct s3c2410_dma_chan *chan) -{ -#if 0 - pr_debug("dma%d: s3c2410_dma_lastxfer: load_state %d\n", - chan->number, chan->load_state); -#endif - - switch (chan->load_state) { - case S3C2410_DMALOAD_NONE: - break; - - case S3C2410_DMALOAD_1LOADED: - if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { - /* flag error? */ - printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n", - chan->number, __FUNCTION__); - return; - } - break; - - case S3C2410_DMALOAD_1LOADED_1RUNNING: - /* I belive in this case we do not have anything to do - * until the next buffer comes along, and we turn off the - * reload */ - return; - - default: - pr_debug("dma%d: lastxfer: unhandled load_state %d with no next\n", - chan->number, chan->load_state); - return; - - } - - /* hopefully this'll shut the damned thing up after the transfer... */ - dma_wrreg(chan, S3C2410_DMA_DCON, chan->dcon | S3C2410_DCON_NORELOAD); -} - - -#define dmadbg2(x...) - -static irqreturn_t -s3c2410_dma_irq(int irq, void *devpw) -{ - struct s3c2410_dma_chan *chan = (struct s3c2410_dma_chan *)devpw; - struct s3c2410_dma_buf *buf; - - buf = chan->curr; - - dbg_showchan(chan); - - /* modify the channel state */ - - switch (chan->load_state) { - case S3C2410_DMALOAD_1RUNNING: - /* TODO - if we are running only one buffer, we probably - * want to reload here, and then worry about the buffer - * callback */ - - chan->load_state = S3C2410_DMALOAD_NONE; - break; - - case S3C2410_DMALOAD_1LOADED: - /* iirc, we should go back to NONE loaded here, we - * had a buffer, and it was never verified as being - * loaded. - */ - - chan->load_state = S3C2410_DMALOAD_NONE; - break; - - case S3C2410_DMALOAD_1LOADED_1RUNNING: - /* we'll worry about checking to see if another buffer is - * ready after we've called back the owner. This should - * ensure we do not wait around too long for the DMA - * engine to start the next transfer - */ - - chan->load_state = S3C2410_DMALOAD_1LOADED; - break; - - case S3C2410_DMALOAD_NONE: - printk(KERN_ERR "dma%d: IRQ with no loaded buffer?\n", - chan->number); - break; - - default: - printk(KERN_ERR "dma%d: IRQ in invalid load_state %d\n", - chan->number, chan->load_state); - break; - } - - if (buf != NULL) { - /* update the chain to make sure that if we load any more - * buffers when we call the callback function, things should - * work properly */ - - chan->curr = buf->next; - buf->next = NULL; - - if (buf->magic != BUF_MAGIC) { - printk(KERN_ERR "dma%d: %s: buf %p incorrect magic\n", - chan->number, __FUNCTION__, buf); - return IRQ_HANDLED; - } - - s3c2410_dma_buffdone(chan, buf, S3C2410_RES_OK); - - /* free resouces */ - s3c2410_dma_freebuf(buf); - } else { - } - - /* only reload if the channel is still running... our buffer done - * routine may have altered the state by requesting the dma channel - * to stop or shutdown... */ - - /* todo: check that when the channel is shut-down from inside this - * function, we cope with unsetting reload, etc */ - - if (chan->next != NULL && chan->state != S3C2410_DMA_IDLE) { - unsigned long flags; - - switch (chan->load_state) { - case S3C2410_DMALOAD_1RUNNING: - /* don't need to do anything for this state */ - break; - - case S3C2410_DMALOAD_NONE: - /* can load buffer immediately */ - break; - - case S3C2410_DMALOAD_1LOADED: - if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { - /* flag error? */ - printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n", - chan->number, __FUNCTION__); - return IRQ_HANDLED; - } - - break; - - case S3C2410_DMALOAD_1LOADED_1RUNNING: - goto no_load; - - default: - printk(KERN_ERR "dma%d: unknown load_state in irq, %d\n", - chan->number, chan->load_state); - return IRQ_HANDLED; - } - - local_irq_save(flags); - s3c2410_dma_loadbuffer(chan, chan->next); - local_irq_restore(flags); - } else { - s3c2410_dma_lastxfer(chan); - - /* see if we can stop this channel.. */ - if (chan->load_state == S3C2410_DMALOAD_NONE) { - pr_debug("dma%d: end of transfer, stopping channel (%ld)\n", - chan->number, jiffies); - s3c2410_dma_ctrl(chan->number | DMACH_LOW_LEVEL, - S3C2410_DMAOP_STOP); - } - } - - no_load: - return IRQ_HANDLED; -} - -static struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel); - -/* s3c2410_request_dma - * - * get control of an dma channel -*/ - -int s3c2410_dma_request(unsigned int channel, - struct s3c2410_dma_client *client, - void *dev) -{ - struct s3c2410_dma_chan *chan; - unsigned long flags; - int err; - - pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n", - channel, client->name, dev); - - local_irq_save(flags); - - chan = s3c2410_dma_map_channel(channel); - if (chan == NULL) { - local_irq_restore(flags); - return -EBUSY; - } - - dbg_showchan(chan); - - chan->client = client; - chan->in_use = 1; - - if (!chan->irq_claimed) { - pr_debug("dma%d: %s : requesting irq %d\n", - channel, __FUNCTION__, chan->irq); - - chan->irq_claimed = 1; - local_irq_restore(flags); - - err = request_irq(chan->irq, s3c2410_dma_irq, IRQF_DISABLED, - client->name, (void *)chan); - - local_irq_save(flags); - - if (err) { - chan->in_use = 0; - chan->irq_claimed = 0; - local_irq_restore(flags); - - printk(KERN_ERR "%s: cannot get IRQ %d for DMA %d\n", - client->name, chan->irq, chan->number); - return err; - } - - chan->irq_enabled = 1; - } - - local_irq_restore(flags); - - /* need to setup */ - - pr_debug("%s: channel initialised, %p\n", __FUNCTION__, chan); - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_request); - -/* s3c2410_dma_free - * - * release the given channel back to the system, will stop and flush - * any outstanding transfers, and ensure the channel is ready for the - * next claimant. - * - * Note, although a warning is currently printed if the freeing client - * info is not the same as the registrant's client info, the free is still - * allowed to go through. -*/ +static struct s3c24xx_dma_selection __initdata s3c2410_dma_sel = { + .select = s3c2410_dma_select, + .dcon_mask = 7 << 24, + .map = s3c2410_dma_mappings, + .map_size = ARRAY_SIZE(s3c2410_dma_mappings), +}; -int s3c2410_dma_free(dmach_t channel, struct s3c2410_dma_client *client) +static int s3c2410_dma_add(struct sys_device *sysdev) { - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - unsigned long flags; - - if (chan == NULL) - return -EINVAL; - - local_irq_save(flags); - - if (chan->client != client) { - printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n", - channel, chan->client, client); - } - - /* sort out stopping and freeing the channel */ - - if (chan->state != S3C2410_DMA_IDLE) { - pr_debug("%s: need to stop dma channel %p\n", - __FUNCTION__, chan); - - /* possibly flush the channel */ - s3c2410_dma_ctrl(channel, S3C2410_DMAOP_STOP); - } - - chan->client = NULL; - chan->in_use = 0; - - if (chan->irq_claimed) - free_irq(chan->irq, (void *)chan); - - chan->irq_claimed = 0; - - if (!(channel & DMACH_LOW_LEVEL)) - dma_chan_map[channel] = NULL; - - local_irq_restore(flags); - - return 0; + return s3c24xx_dma_init_map(&s3c2410_dma_sel); } -EXPORT_SYMBOL(s3c2410_dma_free); - -static int s3c2410_dma_dostop(struct s3c2410_dma_chan *chan) -{ - unsigned long flags; - unsigned long tmp; - - pr_debug("%s:\n", __FUNCTION__); - - dbg_showchan(chan); - - local_irq_save(flags); - - s3c2410_dma_call_op(chan, S3C2410_DMAOP_STOP); - - tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); - tmp |= S3C2410_DMASKTRIG_STOP; - //tmp &= ~S3C2410_DMASKTRIG_ON; - dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp); - -#if 0 - /* should also clear interrupts, according to WinCE BSP */ - tmp = dma_rdreg(chan, S3C2410_DMA_DCON); - tmp |= S3C2410_DCON_NORELOAD; - dma_wrreg(chan, S3C2410_DMA_DCON, tmp); -#endif - - /* should stop do this, or should we wait for flush? */ - chan->state = S3C2410_DMA_IDLE; - chan->load_state = S3C2410_DMALOAD_NONE; - - local_irq_restore(flags); - - return 0; -} +#if defined(CONFIG_CPU_S3C2410) +static struct sysdev_driver s3c2410_dma_driver = { + .add = s3c2410_dma_add, +}; -void s3c2410_dma_waitforstop(struct s3c2410_dma_chan *chan) +static int __init s3c2410_dma_init(void) { - unsigned long tmp; - unsigned int timeout = 0x10000; - - while (timeout-- > 0) { - tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); - - if (!(tmp & S3C2410_DMASKTRIG_ON)) - return; - } - - pr_debug("dma%d: failed to stop?\n", chan->number); + return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_dma_driver); } - -/* s3c2410_dma_flush - * - * stop the channel, and remove all current and pending transfers -*/ - -static int s3c2410_dma_flush(struct s3c2410_dma_chan *chan) -{ - struct s3c2410_dma_buf *buf, *next; - unsigned long flags; - - pr_debug("%s: chan %p (%d)\n", __FUNCTION__, chan, chan->number); - - dbg_showchan(chan); - - local_irq_save(flags); - - if (chan->state != S3C2410_DMA_IDLE) { - pr_debug("%s: stopping channel...\n", __FUNCTION__ ); - s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_STOP); - } - - buf = chan->curr; - if (buf == NULL) - buf = chan->next; - - chan->curr = chan->next = chan->end = NULL; - - if (buf != NULL) { - for ( ; buf != NULL; buf = next) { - next = buf->next; - - pr_debug("%s: free buffer %p, next %p\n", - __FUNCTION__, buf, buf->next); - - s3c2410_dma_buffdone(chan, buf, S3C2410_RES_ABORT); - s3c2410_dma_freebuf(buf); - } - } - - dbg_showregs(chan); - - s3c2410_dma_waitforstop(chan); - -#if 0 - /* should also clear interrupts, according to WinCE BSP */ - { - unsigned long tmp; - - tmp = dma_rdreg(chan, S3C2410_DMA_DCON); - tmp |= S3C2410_DCON_NORELOAD; - dma_wrreg(chan, S3C2410_DMA_DCON, tmp); - } +arch_initcall(s3c2410_dma_init); #endif - dbg_showregs(chan); - - local_irq_restore(flags); - - return 0; -} - -int -s3c2410_dma_started(struct s3c2410_dma_chan *chan) -{ - unsigned long flags; - - local_irq_save(flags); - - dbg_showchan(chan); - - /* if we've only loaded one buffer onto the channel, then chec - * to see if we have another, and if so, try and load it so when - * the first buffer is finished, the new one will be loaded onto - * the channel */ - - if (chan->next != NULL) { - if (chan->load_state == S3C2410_DMALOAD_1LOADED) { - - if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { - pr_debug("%s: buff not yet loaded, no more todo\n", - __FUNCTION__); - } else { - chan->load_state = S3C2410_DMALOAD_1RUNNING; - s3c2410_dma_loadbuffer(chan, chan->next); - } - - } else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) { - s3c2410_dma_loadbuffer(chan, chan->next); - } - } - - - local_irq_restore(flags); - - return 0; - -} - -int -s3c2410_dma_ctrl(dmach_t channel, enum s3c2410_chan_op op) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - switch (op) { - case S3C2410_DMAOP_START: - return s3c2410_dma_start(chan); - - case S3C2410_DMAOP_STOP: - return s3c2410_dma_dostop(chan); - - case S3C2410_DMAOP_PAUSE: - case S3C2410_DMAOP_RESUME: - return -ENOENT; - - case S3C2410_DMAOP_FLUSH: - return s3c2410_dma_flush(chan); - - case S3C2410_DMAOP_STARTED: - return s3c2410_dma_started(chan); - - case S3C2410_DMAOP_TIMEOUT: - return 0; - - } - - return -ENOENT; /* unknown, don't bother */ -} - -EXPORT_SYMBOL(s3c2410_dma_ctrl); - -/* DMA configuration for each channel - * - * DISRCC -> source of the DMA (AHB,APB) - * DISRC -> source address of the DMA - * DIDSTC -> destination of the DMA (AHB,APD) - * DIDST -> destination address of the DMA -*/ - -/* s3c2410_dma_config - * - * xfersize: size of unit in bytes (1,2,4) - * dcon: base value of the DCONx register -*/ - -int s3c2410_dma_config(dmach_t channel, - int xferunit, - int dcon) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n", - __FUNCTION__, channel, xferunit, dcon); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: Initial dcon is %08x\n", __FUNCTION__, dcon); - - dcon |= chan->dcon & dma_sel.dcon_mask; - - pr_debug("%s: New dcon is %08x\n", __FUNCTION__, dcon); - - switch (xferunit) { - case 1: - dcon |= S3C2410_DCON_BYTE; - break; - - case 2: - dcon |= S3C2410_DCON_HALFWORD; - break; - - case 4: - dcon |= S3C2410_DCON_WORD; - break; - - default: - pr_debug("%s: bad transfer size %d\n", __FUNCTION__, xferunit); - return -EINVAL; - } - - dcon |= S3C2410_DCON_HWTRIG; - dcon |= S3C2410_DCON_INTREQ; - - pr_debug("%s: dcon now %08x\n", __FUNCTION__, dcon); - - chan->dcon = dcon; - chan->xfer_unit = xferunit; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_config); - -int s3c2410_dma_setflags(dmach_t channel, unsigned int flags) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: chan=%p, flags=%08x\n", __FUNCTION__, chan, flags); - - chan->flags = flags; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_setflags); - - -/* do we need to protect the settings of the fields from - * irq? -*/ - -int s3c2410_dma_set_opfn(dmach_t channel, s3c2410_dma_opfn_t rtn) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: chan=%p, op rtn=%p\n", __FUNCTION__, chan, rtn); - - chan->op_fn = rtn; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_set_opfn); - -int s3c2410_dma_set_buffdone_fn(dmach_t channel, s3c2410_dma_cbfn_t rtn) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: chan=%p, callback rtn=%p\n", __FUNCTION__, chan, rtn); - - chan->callback_fn = rtn; - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn); - -/* s3c2410_dma_devconfig - * - * configure the dma source/destination hardware type and address - * - * source: S3C2410_DMASRC_HW: source is hardware - * S3C2410_DMASRC_MEM: source is memory - * - * hwcfg: the value for xxxSTCn register, - * bit 0: 0=increment pointer, 1=leave pointer - * bit 1: 0=soucre is AHB, 1=soucre is APB - * - * devaddr: physical address of the source -*/ - -int s3c2410_dma_devconfig(int channel, - enum s3c2410_dmasrc source, - int hwcfg, - unsigned long devaddr) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n", - __FUNCTION__, (int)source, hwcfg, devaddr); - - chan->source = source; - chan->dev_addr = devaddr; - - switch (source) { - case S3C2410_DMASRC_HW: - /* source is hardware */ - pr_debug("%s: hw source, devaddr=%08lx, hwcfg=%d\n", - __FUNCTION__, devaddr, hwcfg); - dma_wrreg(chan, S3C2410_DMA_DISRCC, hwcfg & 3); - dma_wrreg(chan, S3C2410_DMA_DISRC, devaddr); - dma_wrreg(chan, S3C2410_DMA_DIDSTC, (0<<1) | (0<<0)); - - chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DIDST); - return 0; - - case S3C2410_DMASRC_MEM: - /* source is memory */ - pr_debug( "%s: mem source, devaddr=%08lx, hwcfg=%d\n", - __FUNCTION__, devaddr, hwcfg); - dma_wrreg(chan, S3C2410_DMA_DISRCC, (0<<1) | (0<<0)); - dma_wrreg(chan, S3C2410_DMA_DIDST, devaddr); - dma_wrreg(chan, S3C2410_DMA_DIDSTC, hwcfg & 3); - - chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DISRC); - return 0; - } - - printk(KERN_ERR "dma%d: invalid source type (%d)\n", channel, source); - return -EINVAL; -} - -EXPORT_SYMBOL(s3c2410_dma_devconfig); - -/* s3c2410_dma_getposition - * - * returns the current transfer points for the dma source and destination -*/ - -int s3c2410_dma_getposition(dmach_t channel, dma_addr_t *src, dma_addr_t *dst) -{ - struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); - - if (chan == NULL) - return -EINVAL; - - if (src != NULL) - *src = dma_rdreg(chan, S3C2410_DMA_DCSRC); - - if (dst != NULL) - *dst = dma_rdreg(chan, S3C2410_DMA_DCDST); - - return 0; -} - -EXPORT_SYMBOL(s3c2410_dma_getposition); - - -/* system device class */ - -#ifdef CONFIG_PM - -static int s3c2410_dma_suspend(struct sys_device *dev, pm_message_t state) -{ - struct s3c2410_dma_chan *cp = container_of(dev, struct s3c2410_dma_chan, dev); - - printk(KERN_DEBUG "suspending dma channel %d\n", cp->number); - - if (dma_rdreg(cp, S3C2410_DMA_DMASKTRIG) & S3C2410_DMASKTRIG_ON) { - /* the dma channel is still working, which is probably - * a bad thing to do over suspend/resume. We stop the - * channel and assume that the client is either going to - * retry after resume, or that it is broken. - */ - - printk(KERN_INFO "dma: stopping channel %d due to suspend\n", - cp->number); - - s3c2410_dma_dostop(cp); - } - - return 0; -} - -static int s3c2410_dma_resume(struct sys_device *dev) -{ - return 0; -} - -#else -#define s3c2410_dma_suspend NULL -#define s3c2410_dma_resume NULL -#endif /* CONFIG_PM */ - -struct sysdev_class dma_sysclass = { - set_kset_name("s3c24xx-dma"), - .suspend = s3c2410_dma_suspend, - .resume = s3c2410_dma_resume, +#if defined(CONFIG_CPU_S3C2442) +/* S3C2442 DMA contains the same selection table as the S3C2410 */ +static struct sysdev_driver s3c2442_dma_driver = { + .add = s3c2410_dma_add, }; -/* kmem cache implementation */ - -static void s3c2410_dma_cache_ctor(void *p, struct kmem_cache *c, unsigned long f) -{ - memset(p, 0, sizeof(struct s3c2410_dma_buf)); -} - -/* initialisation code */ - -static int __init s3c2410_init_dma(void) -{ - struct s3c2410_dma_chan *cp; - int channel; - int ret; - - printk("S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics\n"); - - dma_base = ioremap(S3C24XX_PA_DMA, 0x200); - if (dma_base == NULL) { - printk(KERN_ERR "dma failed to remap register block\n"); - return -ENOMEM; - } - - printk("Registering sysclass\n"); - - ret = sysdev_class_register(&dma_sysclass); - if (ret != 0) { - printk(KERN_ERR "dma sysclass registration failed\n"); - goto err; - } - - dma_kmem = kmem_cache_create("dma_desc", sizeof(struct s3c2410_dma_buf), 0, - SLAB_HWCACHE_ALIGN, - s3c2410_dma_cache_ctor, NULL); - - if (dma_kmem == NULL) { - printk(KERN_ERR "dma failed to make kmem cache\n"); - ret = -ENOMEM; - goto err; - } - - for (channel = 0; channel < S3C2410_DMA_CHANNELS; channel++) { - cp = &s3c2410_chans[channel]; - - memset(cp, 0, sizeof(struct s3c2410_dma_chan)); - - /* dma channel irqs are in order.. */ - cp->number = channel; - cp->irq = channel + IRQ_DMA0; - cp->regs = dma_base + (channel*0x40); - - /* point current stats somewhere */ - cp->stats = &cp->stats_store; - cp->stats_store.timeout_shortest = LONG_MAX; - - /* basic channel configuration */ - - cp->load_timeout = 1<<18; - - /* register system device */ - - cp->dev.cls = &dma_sysclass; - cp->dev.id = channel; - ret = sysdev_register(&cp->dev); - - printk("DMA channel %d at %p, irq %d\n", - cp->number, cp->regs, cp->irq); - } - - return 0; - - err: - kmem_cache_destroy(dma_kmem); - iounmap(dma_base); - dma_base = NULL; - return ret; -} - -core_initcall(s3c2410_init_dma); - -static inline int is_channel_valid(unsigned int channel) +static int __init s3c2442_dma_init(void) { - return (channel & DMA_CH_VALID); + return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_dma_driver); } -/* s3c2410_dma_map_channel() - * - * turn the virtual channel number into a real, and un-used hardware - * channel. - * - * currently this code uses first-free channel from the specified harware - * map, not taking into account anything that the board setup code may - * have to say about the likely peripheral set to be in use. -*/ - -struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) -{ - struct s3c24xx_dma_map *ch_map; - struct s3c2410_dma_chan *dmach; - int ch; - - if (dma_sel.map == NULL || channel > dma_sel.map_size) - return NULL; - - ch_map = dma_sel.map + channel; - - for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) { - if (!is_channel_valid(ch_map->channels[ch])) - continue; - - if (s3c2410_chans[ch].in_use == 0) { - printk("mapped channel %d to %d\n", channel, ch); - break; - } - } - - if (ch >= S3C2410_DMA_CHANNELS) - return NULL; - - /* update our channel mapping */ - - dmach = &s3c2410_chans[ch]; - dma_chan_map[channel] = dmach; - - /* select the channel */ - - (dma_sel.select)(dmach, ch_map); - - return dmach; -} - -static void s3c24xx_dma_show_ch(struct s3c24xx_dma_map *map, int ch) -{ - /* show the channel configuration */ - - printk("%2d: %20s, channels %c%c%c%c\n", ch, map->name, - (is_channel_valid(map->channels[0]) ? '0' : '-'), - (is_channel_valid(map->channels[1]) ? '1' : '-'), - (is_channel_valid(map->channels[2]) ? '2' : '-'), - (is_channel_valid(map->channels[3]) ? '3' : '-')); -} - -static int s3c24xx_dma_check_entry(struct s3c24xx_dma_map *map, int ch) -{ - if (1) - s3c24xx_dma_show_ch(map, ch); - - return 0; -} - -int __init s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel) -{ - struct s3c24xx_dma_map *nmap; - size_t map_sz = sizeof(*nmap) * sel->map_size; - int ptr; - - nmap = kmalloc(map_sz, GFP_KERNEL); - if (nmap == NULL) - return -ENOMEM; - - memcpy(nmap, sel->map, map_sz); - memcpy(&dma_sel, sel, sizeof(*sel)); - - dma_sel.map = nmap; - - for (ptr = 0; ptr < sel->map_size; ptr++) - s3c24xx_dma_check_entry(nmap+ptr, ptr); +arch_initcall(s3c2442_dma_init); +#endif - return 0; -} diff --git a/arch/arm/mach-s3c2410/dma.h b/arch/arm/mach-s3c2410/dma.h deleted file mode 100644 index 0ebfe0aab80b..000000000000 --- a/arch/arm/mach-s3c2410/dma.h +++ /dev/null @@ -1,45 +0,0 @@ -/* arch/arm/mach-s3c2410/dma.h - * - * Copyright (C) 2006 Simtec Electronics - * Ben Dooks - * - * Samsung S3C24XX DMA support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -extern struct sysdev_class dma_sysclass; -extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; - -#define DMA_CH_VALID (1<<31) - -struct s3c24xx_dma_addr { - unsigned long from; - unsigned long to; -}; - -/* struct s3c24xx_dma_map - * - * this holds the mapping information for the channel selected - * to be connected to the specified device -*/ - -struct s3c24xx_dma_map { - const char *name; - struct s3c24xx_dma_addr hw_addr; - - unsigned long channels[S3C2410_DMA_CHANNELS]; -}; - -struct s3c24xx_dma_selection { - struct s3c24xx_dma_map *map; - unsigned long map_size; - unsigned long dcon_mask; - - void (*select)(struct s3c2410_dma_chan *chan, - struct s3c24xx_dma_map *map); -}; - -extern int s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel); diff --git a/arch/arm/mach-s3c2410/gpio.c b/arch/arm/mach-s3c2410/gpio.c index f6fb215bb48c..01e795d1146e 100644 --- a/arch/arm/mach-s3c2410/gpio.c +++ b/arch/arm/mach-s3c2410/gpio.c @@ -1,9 +1,9 @@ /* linux/arch/arm/mach-s3c2410/gpio.c * - * Copyright (c) 2004-2005 Simtec Electronics + * Copyright (c) 2004-2006 Simtec Electronics * Ben Dooks * - * S3C24XX GPIO support + * S3C2410 GPIO support * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -18,8 +18,7 @@ * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - + */ #include #include @@ -33,156 +32,40 @@ #include -void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function) -{ - void __iomem *base = S3C24XX_GPIO_BASE(pin); - unsigned long mask; - unsigned long con; - unsigned long flags; - - if (pin < S3C2410_GPIO_BANKB) { - mask = 1 << S3C2410_GPIO_OFFSET(pin); - } else { - mask = 3 << S3C2410_GPIO_OFFSET(pin)*2; - } - - switch (function) { - case S3C2410_GPIO_LEAVE: - mask = 0; - function = 0; - break; - - case S3C2410_GPIO_INPUT: - case S3C2410_GPIO_OUTPUT: - case S3C2410_GPIO_SFN2: - case S3C2410_GPIO_SFN3: - if (pin < S3C2410_GPIO_BANKB) { - function -= 1; - function &= 1; - function <<= S3C2410_GPIO_OFFSET(pin); - } else { - function &= 3; - function <<= S3C2410_GPIO_OFFSET(pin)*2; - } - } - - /* modify the specified register wwith IRQs off */ - - local_irq_save(flags); - - con = __raw_readl(base + 0x00); - con &= ~mask; - con |= function; - - __raw_writel(con, base + 0x00); - - local_irq_restore(flags); -} - -EXPORT_SYMBOL(s3c2410_gpio_cfgpin); - -unsigned int s3c2410_gpio_getcfg(unsigned int pin) -{ - void __iomem *base = S3C24XX_GPIO_BASE(pin); - unsigned long val = __raw_readl(base); - - if (pin < S3C2410_GPIO_BANKB) { - val >>= S3C2410_GPIO_OFFSET(pin); - val &= 1; - val += 1; - } else { - val >>= S3C2410_GPIO_OFFSET(pin)*2; - val &= 3; - } - - return val | S3C2410_GPIO_INPUT; -} - -EXPORT_SYMBOL(s3c2410_gpio_getcfg); - -void s3c2410_gpio_pullup(unsigned int pin, unsigned int to) +int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, + unsigned int config) { - void __iomem *base = S3C24XX_GPIO_BASE(pin); - unsigned long offs = S3C2410_GPIO_OFFSET(pin); + void __iomem *reg = S3C24XX_EINFLT0; unsigned long flags; - unsigned long up; - - if (pin < S3C2410_GPIO_BANKB) - return; - - local_irq_save(flags); - - up = __raw_readl(base + 0x08); - up &= ~(1L << offs); - up |= to << offs; - __raw_writel(up, base + 0x08); + unsigned long val; - local_irq_restore(flags); -} + if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15) + return -1; -EXPORT_SYMBOL(s3c2410_gpio_pullup); + config &= 0xff; -void s3c2410_gpio_setpin(unsigned int pin, unsigned int to) -{ - void __iomem *base = S3C24XX_GPIO_BASE(pin); - unsigned long offs = S3C2410_GPIO_OFFSET(pin); - unsigned long flags; - unsigned long dat; + pin -= S3C2410_GPG8; + reg += pin & ~3; local_irq_save(flags); - dat = __raw_readl(base + 0x04); - dat &= ~(1 << offs); - dat |= to << offs; - __raw_writel(dat, base + 0x04); - - local_irq_restore(flags); -} - -EXPORT_SYMBOL(s3c2410_gpio_setpin); - -unsigned int s3c2410_gpio_getpin(unsigned int pin) -{ - void __iomem *base = S3C24XX_GPIO_BASE(pin); - unsigned long offs = S3C2410_GPIO_OFFSET(pin); + /* update filter width and clock source */ - return __raw_readl(base + 0x04) & (1<< offs); -} + val = __raw_readl(reg); + val &= ~(0xff << ((pin & 3) * 8)); + val |= config << ((pin & 3) * 8); + __raw_writel(val, reg); -EXPORT_SYMBOL(s3c2410_gpio_getpin); + /* update filter enable */ -unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change) -{ - unsigned long flags; - unsigned long misccr; + val = __raw_readl(S3C24XX_EXTINT2); + val &= ~(1 << ((pin * 4) + 3)); + val |= on << ((pin * 4) + 3); + __raw_writel(val, S3C24XX_EXTINT2); - local_irq_save(flags); - misccr = __raw_readl(S3C24XX_MISCCR); - misccr &= ~clear; - misccr ^= change; - __raw_writel(misccr, S3C24XX_MISCCR); local_irq_restore(flags); - return misccr; -} - -EXPORT_SYMBOL(s3c2410_modify_misccr); - -int s3c2410_gpio_getirq(unsigned int pin) -{ - if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15) - return -1; /* not valid interrupts */ - - if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7) - return -1; /* not valid pin */ - - if (pin < S3C2410_GPF4) - return (pin - S3C2410_GPF0) + IRQ_EINT0; - - if (pin < S3C2410_GPG0) - return (pin - S3C2410_GPF4) + IRQ_EINT4; - - return (pin - S3C2410_GPG0) + IRQ_EINT8; + return 0; } -EXPORT_SYMBOL(s3c2410_gpio_getirq); +EXPORT_SYMBOL(s3c2410_gpio_irqfilter); diff --git a/arch/arm/mach-s3c2410/irq.c b/arch/arm/mach-s3c2410/irq.c index 3c0ed7871c55..53cbdaa43ac6 100644 --- a/arch/arm/mach-s3c2410/irq.c +++ b/arch/arm/mach-s3c2410/irq.c @@ -1,6 +1,6 @@ /* linux/arch/arm/mach-s3c2410/irq.c * - * Copyright (c) 2003,2004 Simtec Electronics + * Copyright (c) 2006 Simtec Electronics * Ben Dooks * * This program is free software; you can redistribute it and/or modify @@ -17,37 +17,6 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * - * Changelog: - * - * 22-Jul-2004 Ben Dooks - * Fixed compile warnings - * - * 22-Jul-2004 Roc Wu - * Fixed s3c_extirq_type - * - * 21-Jul-2004 Arnaud Patard (Rtp) - * Addition of ADC/TC demux - * - * 04-Oct-2004 Klaus Fetscher - * Fix for set_irq_type() on low EINT numbers - * - * 05-Oct-2004 Ben Dooks - * Tidy up KF's patch and sort out new release - * - * 05-Oct-2004 Ben Dooks - * Add support for power management controls - * - * 04-Nov-2004 Ben Dooks - * Fix standard IRQ wake for EINT0..4 and RTC - * - * 22-Feb-2005 Ben Dooks - * Fixed edge-triggering on ADC IRQ - * - * 28-Jun-2005 Ben Dooks - * Mark IRQ_LCD valid - * - * 25-Jul-2005 Ben Dooks - * Split the S3C2440 IRQ code to seperate file */ #include @@ -57,745 +26,23 @@ #include #include -#include -#include -#include - -#include - -#include -#include - -#include "cpu.h" -#include "pm.h" -#include "irq.h" - -/* wakeup irq control */ - -#ifdef CONFIG_PM - -/* state for IRQs over sleep */ - -/* default is to allow for EINT0..EINT15, and IRQ_RTC as wakeup sources - * - * set bit to 1 in allow bitfield to enable the wakeup settings on it -*/ - -unsigned long s3c_irqwake_intallow = 1L << (IRQ_RTC - IRQ_EINT0) | 0xfL; -unsigned long s3c_irqwake_intmask = 0xffffffffL; -unsigned long s3c_irqwake_eintallow = 0x0000fff0L; -unsigned long s3c_irqwake_eintmask = 0xffffffffL; - -int -s3c_irq_wake(unsigned int irqno, unsigned int state) -{ - unsigned long irqbit = 1 << (irqno - IRQ_EINT0); - - if (!(s3c_irqwake_intallow & irqbit)) - return -ENOENT; - - printk(KERN_INFO "wake %s for irq %d\n", - state ? "enabled" : "disabled", irqno); - - if (!state) - s3c_irqwake_intmask |= irqbit; - else - s3c_irqwake_intmask &= ~irqbit; - - return 0; -} - -static int -s3c_irqext_wake(unsigned int irqno, unsigned int state) -{ - unsigned long bit = 1L << (irqno - EXTINT_OFF); - - if (!(s3c_irqwake_eintallow & bit)) - return -ENOENT; - - printk(KERN_INFO "wake %s for irq %d\n", - state ? "enabled" : "disabled", irqno); - - if (!state) - s3c_irqwake_eintmask |= bit; - else - s3c_irqwake_eintmask &= ~bit; - - return 0; -} - -#else -#define s3c_irqext_wake NULL -#define s3c_irq_wake NULL -#endif - - -static void -s3c_irq_mask(unsigned int irqno) -{ - unsigned long mask; - - irqno -= IRQ_EINT0; - - mask = __raw_readl(S3C2410_INTMSK); - mask |= 1UL << irqno; - __raw_writel(mask, S3C2410_INTMSK); -} - -static inline void -s3c_irq_ack(unsigned int irqno) -{ - unsigned long bitval = 1UL << (irqno - IRQ_EINT0); - - __raw_writel(bitval, S3C2410_SRCPND); - __raw_writel(bitval, S3C2410_INTPND); -} - -static inline void -s3c_irq_maskack(unsigned int irqno) -{ - unsigned long bitval = 1UL << (irqno - IRQ_EINT0); - unsigned long mask; - - mask = __raw_readl(S3C2410_INTMSK); - __raw_writel(mask|bitval, S3C2410_INTMSK); - - __raw_writel(bitval, S3C2410_SRCPND); - __raw_writel(bitval, S3C2410_INTPND); -} - - -static void -s3c_irq_unmask(unsigned int irqno) -{ - unsigned long mask; - - if (irqno != IRQ_TIMER4 && irqno != IRQ_EINT8t23) - irqdbf2("s3c_irq_unmask %d\n", irqno); - - irqno -= IRQ_EINT0; - - mask = __raw_readl(S3C2410_INTMSK); - mask &= ~(1UL << irqno); - __raw_writel(mask, S3C2410_INTMSK); -} - -struct irq_chip s3c_irq_level_chip = { - .name = "s3c-level", - .ack = s3c_irq_maskack, - .mask = s3c_irq_mask, - .unmask = s3c_irq_unmask, - .set_wake = s3c_irq_wake -}; - -static struct irq_chip s3c_irq_chip = { - .name = "s3c", - .ack = s3c_irq_ack, - .mask = s3c_irq_mask, - .unmask = s3c_irq_unmask, - .set_wake = s3c_irq_wake -}; - -static void -s3c_irqext_mask(unsigned int irqno) -{ - unsigned long mask; - - irqno -= EXTINT_OFF; - - mask = __raw_readl(S3C24XX_EINTMASK); - mask |= ( 1UL << irqno); - __raw_writel(mask, S3C24XX_EINTMASK); -} - -static void -s3c_irqext_ack(unsigned int irqno) -{ - unsigned long req; - unsigned long bit; - unsigned long mask; +#include +#include - bit = 1UL << (irqno - EXTINT_OFF); - - mask = __raw_readl(S3C24XX_EINTMASK); - - __raw_writel(bit, S3C24XX_EINTPEND); - - req = __raw_readl(S3C24XX_EINTPEND); - req &= ~mask; - - /* not sure if we should be acking the parent irq... */ - - if (irqno <= IRQ_EINT7 ) { - if ((req & 0xf0) == 0) - s3c_irq_ack(IRQ_EINT4t7); - } else { - if ((req >> 8) == 0) - s3c_irq_ack(IRQ_EINT8t23); - } -} - -static void -s3c_irqext_unmask(unsigned int irqno) +static int s3c2410_irq_add(struct sys_device *sysdev) { - unsigned long mask; - - irqno -= EXTINT_OFF; - - mask = __raw_readl(S3C24XX_EINTMASK); - mask &= ~( 1UL << irqno); - __raw_writel(mask, S3C24XX_EINTMASK); -} - -int -s3c_irqext_type(unsigned int irq, unsigned int type) -{ - void __iomem *extint_reg; - void __iomem *gpcon_reg; - unsigned long gpcon_offset, extint_offset; - unsigned long newvalue = 0, value; - - if ((irq >= IRQ_EINT0) && (irq <= IRQ_EINT3)) - { - gpcon_reg = S3C2410_GPFCON; - extint_reg = S3C24XX_EXTINT0; - gpcon_offset = (irq - IRQ_EINT0) * 2; - extint_offset = (irq - IRQ_EINT0) * 4; - } - else if ((irq >= IRQ_EINT4) && (irq <= IRQ_EINT7)) - { - gpcon_reg = S3C2410_GPFCON; - extint_reg = S3C24XX_EXTINT0; - gpcon_offset = (irq - (EXTINT_OFF)) * 2; - extint_offset = (irq - (EXTINT_OFF)) * 4; - } - else if ((irq >= IRQ_EINT8) && (irq <= IRQ_EINT15)) - { - gpcon_reg = S3C2410_GPGCON; - extint_reg = S3C24XX_EXTINT1; - gpcon_offset = (irq - IRQ_EINT8) * 2; - extint_offset = (irq - IRQ_EINT8) * 4; - } - else if ((irq >= IRQ_EINT16) && (irq <= IRQ_EINT23)) - { - gpcon_reg = S3C2410_GPGCON; - extint_reg = S3C24XX_EXTINT2; - gpcon_offset = (irq - IRQ_EINT8) * 2; - extint_offset = (irq - IRQ_EINT16) * 4; - } else - return -1; - - /* Set the GPIO to external interrupt mode */ - value = __raw_readl(gpcon_reg); - value = (value & ~(3 << gpcon_offset)) | (0x02 << gpcon_offset); - __raw_writel(value, gpcon_reg); - - /* Set the external interrupt to pointed trigger type */ - switch (type) - { - case IRQT_NOEDGE: - printk(KERN_WARNING "No edge setting!\n"); - break; - - case IRQT_RISING: - newvalue = S3C2410_EXTINT_RISEEDGE; - break; - - case IRQT_FALLING: - newvalue = S3C2410_EXTINT_FALLEDGE; - break; - - case IRQT_BOTHEDGE: - newvalue = S3C2410_EXTINT_BOTHEDGE; - break; - - case IRQT_LOW: - newvalue = S3C2410_EXTINT_LOWLEV; - break; - - case IRQT_HIGH: - newvalue = S3C2410_EXTINT_HILEV; - break; - - default: - printk(KERN_ERR "No such irq type %d", type); - return -1; - } - - value = __raw_readl(extint_reg); - value = (value & ~(7 << extint_offset)) | (newvalue << extint_offset); - __raw_writel(value, extint_reg); - return 0; } -static struct irq_chip s3c_irqext_chip = { - .name = "s3c-ext", - .mask = s3c_irqext_mask, - .unmask = s3c_irqext_unmask, - .ack = s3c_irqext_ack, - .set_type = s3c_irqext_type, - .set_wake = s3c_irqext_wake -}; - -static struct irq_chip s3c_irq_eint0t4 = { - .name = "s3c-ext0", - .ack = s3c_irq_ack, - .mask = s3c_irq_mask, - .unmask = s3c_irq_unmask, - .set_wake = s3c_irq_wake, - .set_type = s3c_irqext_type, -}; - -/* mask values for the parent registers for each of the interrupt types */ - -#define INTMSK_UART0 (1UL << (IRQ_UART0 - IRQ_EINT0)) -#define INTMSK_UART1 (1UL << (IRQ_UART1 - IRQ_EINT0)) -#define INTMSK_UART2 (1UL << (IRQ_UART2 - IRQ_EINT0)) -#define INTMSK_ADCPARENT (1UL << (IRQ_ADCPARENT - IRQ_EINT0)) - - -/* UART0 */ - -static void -s3c_irq_uart0_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_UART0, 7); -} - -static void -s3c_irq_uart0_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_UART0); -} - -static void -s3c_irq_uart0_ack(unsigned int irqno) -{ - s3c_irqsub_maskack(irqno, INTMSK_UART0, 7); -} - -static struct irq_chip s3c_irq_uart0 = { - .name = "s3c-uart0", - .mask = s3c_irq_uart0_mask, - .unmask = s3c_irq_uart0_unmask, - .ack = s3c_irq_uart0_ack, -}; - -/* UART1 */ - -static void -s3c_irq_uart1_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_UART1, 7 << 3); -} - -static void -s3c_irq_uart1_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_UART1); -} - -static void -s3c_irq_uart1_ack(unsigned int irqno) -{ - s3c_irqsub_maskack(irqno, INTMSK_UART1, 7 << 3); -} - -static struct irq_chip s3c_irq_uart1 = { - .name = "s3c-uart1", - .mask = s3c_irq_uart1_mask, - .unmask = s3c_irq_uart1_unmask, - .ack = s3c_irq_uart1_ack, -}; - -/* UART2 */ - -static void -s3c_irq_uart2_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_UART2, 7 << 6); -} - -static void -s3c_irq_uart2_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_UART2); -} - -static void -s3c_irq_uart2_ack(unsigned int irqno) -{ - s3c_irqsub_maskack(irqno, INTMSK_UART2, 7 << 6); -} - -static struct irq_chip s3c_irq_uart2 = { - .name = "s3c-uart2", - .mask = s3c_irq_uart2_mask, - .unmask = s3c_irq_uart2_unmask, - .ack = s3c_irq_uart2_ack, -}; - -/* ADC and Touchscreen */ - -static void -s3c_irq_adc_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_ADCPARENT, 3 << 9); -} - -static void -s3c_irq_adc_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_ADCPARENT); -} - -static void -s3c_irq_adc_ack(unsigned int irqno) -{ - s3c_irqsub_ack(irqno, INTMSK_ADCPARENT, 3 << 9); -} - -static struct irq_chip s3c_irq_adc = { - .name = "s3c-adc", - .mask = s3c_irq_adc_mask, - .unmask = s3c_irq_adc_unmask, - .ack = s3c_irq_adc_ack, -}; - -/* irq demux for adc */ -static void s3c_irq_demux_adc(unsigned int irq, - struct irq_desc *desc) -{ - unsigned int subsrc, submsk; - unsigned int offset = 9; - struct irq_desc *mydesc; - - /* read the current pending interrupts, and the mask - * for what it is available */ - - subsrc = __raw_readl(S3C2410_SUBSRCPND); - submsk = __raw_readl(S3C2410_INTSUBMSK); - - subsrc &= ~submsk; - subsrc >>= offset; - subsrc &= 3; - - if (subsrc != 0) { - if (subsrc & 1) { - mydesc = irq_desc + IRQ_TC; - desc_handle_irq(IRQ_TC, mydesc); - } - if (subsrc & 2) { - mydesc = irq_desc + IRQ_ADC; - desc_handle_irq(IRQ_ADC, mydesc); - } - } -} - -static void s3c_irq_demux_uart(unsigned int start) -{ - unsigned int subsrc, submsk; - unsigned int offset = start - IRQ_S3CUART_RX0; - struct irq_desc *desc; - - /* read the current pending interrupts, and the mask - * for what it is available */ - - subsrc = __raw_readl(S3C2410_SUBSRCPND); - submsk = __raw_readl(S3C2410_INTSUBMSK); - - irqdbf2("s3c_irq_demux_uart: start=%d (%d), subsrc=0x%08x,0x%08x\n", - start, offset, subsrc, submsk); - - subsrc &= ~submsk; - subsrc >>= offset; - subsrc &= 7; - - if (subsrc != 0) { - desc = irq_desc + start; - - if (subsrc & 1) - desc_handle_irq(start, desc); - - desc++; - - if (subsrc & 2) - desc_handle_irq(start+1, desc); - - desc++; - - if (subsrc & 4) - desc_handle_irq(start+2, desc); - } -} - -/* uart demux entry points */ - -static void -s3c_irq_demux_uart0(unsigned int irq, - struct irq_desc *desc) -{ - irq = irq; - s3c_irq_demux_uart(IRQ_S3CUART_RX0); -} - -static void -s3c_irq_demux_uart1(unsigned int irq, - struct irq_desc *desc) -{ - irq = irq; - s3c_irq_demux_uart(IRQ_S3CUART_RX1); -} - -static void -s3c_irq_demux_uart2(unsigned int irq, - struct irq_desc *desc) -{ - irq = irq; - s3c_irq_demux_uart(IRQ_S3CUART_RX2); -} - -static void -s3c_irq_demux_extint8(unsigned int irq, - struct irq_desc *desc) -{ - unsigned long eintpnd = __raw_readl(S3C24XX_EINTPEND); - unsigned long eintmsk = __raw_readl(S3C24XX_EINTMASK); - - eintpnd &= ~eintmsk; - eintpnd &= ~0xff; /* ignore lower irqs */ - - /* we may as well handle all the pending IRQs here */ - - while (eintpnd) { - irq = __ffs(eintpnd); - eintpnd &= ~(1< - * - * Header file for S3C24XX CPU IRQ support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#define irqdbf(x...) -#define irqdbf2(x...) - -#define EXTINT_OFF (IRQ_EINT4 - 4) - -extern struct irq_chip s3c_irq_level_chip; - -static inline void -s3c_irqsub_mask(unsigned int irqno, unsigned int parentbit, - int subcheck) -{ - unsigned long mask; - unsigned long submask; - - submask = __raw_readl(S3C2410_INTSUBMSK); - mask = __raw_readl(S3C2410_INTMSK); - - submask |= (1UL << (irqno - IRQ_S3CUART_RX0)); - - /* check to see if we need to mask the parent IRQ */ - - if ((submask & subcheck) == subcheck) { - __raw_writel(mask | parentbit, S3C2410_INTMSK); - } - - /* write back masks */ - __raw_writel(submask, S3C2410_INTSUBMSK); - -} - -static inline void -s3c_irqsub_unmask(unsigned int irqno, unsigned int parentbit) -{ - unsigned long mask; - unsigned long submask; - - submask = __raw_readl(S3C2410_INTSUBMSK); - mask = __raw_readl(S3C2410_INTMSK); - - submask &= ~(1UL << (irqno - IRQ_S3CUART_RX0)); - mask &= ~parentbit; - - /* write back masks */ - __raw_writel(submask, S3C2410_INTSUBMSK); - __raw_writel(mask, S3C2410_INTMSK); -} - - -static inline void -s3c_irqsub_maskack(unsigned int irqno, unsigned int parentmask, unsigned int group) -{ - unsigned int bit = 1UL << (irqno - IRQ_S3CUART_RX0); - - s3c_irqsub_mask(irqno, parentmask, group); - - __raw_writel(bit, S3C2410_SUBSRCPND); - - /* only ack parent if we've got all the irqs (seems we must - * ack, all and hope that the irq system retriggers ok when - * the interrupt goes off again) - */ - - if (1) { - __raw_writel(parentmask, S3C2410_SRCPND); - __raw_writel(parentmask, S3C2410_INTPND); - } -} - -static inline void -s3c_irqsub_ack(unsigned int irqno, unsigned int parentmask, unsigned int group) -{ - unsigned int bit = 1UL << (irqno - IRQ_S3CUART_RX0); - - __raw_writel(bit, S3C2410_SUBSRCPND); - - /* only ack parent if we've got all the irqs (seems we must - * ack, all and hope that the irq system retriggers ok when - * the interrupt goes off again) - */ - - if (1) { - __raw_writel(parentmask, S3C2410_SRCPND); - __raw_writel(parentmask, S3C2410_INTPND); - } -} - -/* exported for use in arch/arm/mach-s3c2410 */ - -#ifdef CONFIG_PM -extern int s3c_irq_wake(unsigned int irqno, unsigned int state); -#else -#define s3c_irq_wake NULL -#endif - -extern int s3c_irqext_type(unsigned int irq, unsigned int type); diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c index 817e2c684410..d54cda1b3006 100644 --- a/arch/arm/mach-s3c2410/mach-amlm5900.c +++ b/arch/arm/mach-s3c2410/mach-amlm5900.c @@ -1,4 +1,4 @@ -/*********************************************************************** +/* linux/arch/arm/mach-s3c2410/mach-amlm5900.c * * linux/arch/arm/mach-s3c2410/mach-amlm5900.c * @@ -52,8 +52,8 @@ #include #include -#include "devs.h" -#include "cpu.h" +#include +#include #ifdef CONFIG_MTD_PARTITIONS diff --git a/arch/arm/mach-s3c2410/mach-anubis.c b/arch/arm/mach-s3c2410/mach-anubis.c deleted file mode 100644 index 0fad0c2fe07b..000000000000 --- a/arch/arm/mach-s3c2410/mach-anubis.c +++ /dev/null @@ -1,325 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-anubis.c - * - * Copyright (c) 2003-2005 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include "clock.h" -#include "devs.h" -#include "cpu.h" - -#define COPYRIGHT ", (c) 2005 Simtec Electronics" - -static struct map_desc anubis_iodesc[] __initdata = { - /* ISA IO areas */ - - { - .virtual = (u32)S3C24XX_VA_ISA_BYTE, - .pfn = __phys_to_pfn(0x0), - .length = SZ_4M, - .type = MT_DEVICE, - }, { - .virtual = (u32)S3C24XX_VA_ISA_WORD, - .pfn = __phys_to_pfn(0x0), - .length = SZ_4M, - .type = MT_DEVICE, - }, - - /* we could possibly compress the next set down into a set of smaller tables - * pagetables, but that would mean using an L2 section, and it still means - * we cannot actually feed the same register to an LDR due to 16K spacing - */ - - /* CPLD control registers */ - - { - .virtual = (u32)ANUBIS_VA_CTRL1, - .pfn = __phys_to_pfn(ANUBIS_PA_CTRL1), - .length = SZ_4K, - .type = MT_DEVICE, - }, { - .virtual = (u32)ANUBIS_VA_CTRL2, - .pfn = __phys_to_pfn(ANUBIS_PA_CTRL2), - .length = SZ_4K, - .type = MT_DEVICE, - }, -}; - -#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK -#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB -#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE - -static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = { - [0] = { - .name = "uclk", - .divisor = 1, - .min_baud = 0, - .max_baud = 0, - }, - [1] = { - .name = "pclk", - .divisor = 1, - .min_baud = 0, - .max_baud = 0, - } -}; - - -static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - .clocks = anubis_serial_clocks, - .clocks_size = ARRAY_SIZE(anubis_serial_clocks), - }, - [1] = { - .hwport = 2, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - .clocks = anubis_serial_clocks, - .clocks_size = ARRAY_SIZE(anubis_serial_clocks), - }, -}; - -/* NAND Flash on Anubis board */ - -static int external_map[] = { 2 }; -static int chip0_map[] = { 0 }; -static int chip1_map[] = { 1 }; - -static struct mtd_partition anubis_default_nand_part[] = { - [0] = { - .name = "Boot Agent", - .size = SZ_16K, - .offset = 0, - }, - [1] = { - .name = "/boot", - .size = SZ_4M - SZ_16K, - .offset = SZ_16K, - }, - [2] = { - .name = "user1", - .offset = SZ_4M, - .size = SZ_32M - SZ_4M, - }, - [3] = { - .name = "user2", - .offset = SZ_32M, - .size = MTDPART_SIZ_FULL, - } -}; - -/* the Anubis has 3 selectable slots for nand-flash, the two - * on-board chip areas, as well as the external slot. - * - * Note, there is no current hot-plug support for the External - * socket. -*/ - -static struct s3c2410_nand_set anubis_nand_sets[] = { - [1] = { - .name = "External", - .nr_chips = 1, - .nr_map = external_map, - .nr_partitions = ARRAY_SIZE(anubis_default_nand_part), - .partitions = anubis_default_nand_part, - }, - [0] = { - .name = "chip0", - .nr_chips = 1, - .nr_map = chip0_map, - .nr_partitions = ARRAY_SIZE(anubis_default_nand_part), - .partitions = anubis_default_nand_part, - }, - [2] = { - .name = "chip1", - .nr_chips = 1, - .nr_map = chip1_map, - .nr_partitions = ARRAY_SIZE(anubis_default_nand_part), - .partitions = anubis_default_nand_part, - }, -}; - -static void anubis_nand_select(struct s3c2410_nand_set *set, int slot) -{ - unsigned int tmp; - - slot = set->nr_map[slot] & 3; - - pr_debug("anubis_nand: selecting slot %d (set %p,%p)\n", - slot, set, set->nr_map); - - tmp = __raw_readb(ANUBIS_VA_CTRL1); - tmp &= ~ANUBIS_CTRL1_NANDSEL; - tmp |= slot; - - pr_debug("anubis_nand: ctrl1 now %02x\n", tmp); - - __raw_writeb(tmp, ANUBIS_VA_CTRL1); -} - -static struct s3c2410_platform_nand anubis_nand_info = { - .tacls = 25, - .twrph0 = 55, - .twrph1 = 40, - .nr_sets = ARRAY_SIZE(anubis_nand_sets), - .sets = anubis_nand_sets, - .select_chip = anubis_nand_select, -}; - -/* IDE channels */ - -static struct resource anubis_ide0_resource[] = { - { - .start = S3C2410_CS3, - .end = S3C2410_CS3 + (8*32) - 1, - .flags = IORESOURCE_MEM, - }, { - .start = S3C2410_CS3 + (1<<26), - .end = S3C2410_CS3 + (1<<26) + (8*32) - 1, - .flags = IORESOURCE_MEM, - }, { - .start = IRQ_IDE0, - .end = IRQ_IDE0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device anubis_device_ide0 = { - .name = "simtec-ide", - .id = 0, - .num_resources = ARRAY_SIZE(anubis_ide0_resource), - .resource = anubis_ide0_resource, -}; - -static struct resource anubis_ide1_resource[] = { - { - .start = S3C2410_CS4, - .end = S3C2410_CS4 + (8*32) - 1, - .flags = IORESOURCE_MEM, - }, { - .start = S3C2410_CS4 + (1<<26), - .end = S3C2410_CS4 + (1<<26) + (8*32) - 1, - .flags = IORESOURCE_MEM, - }, { - .start = IRQ_IDE0, - .end = IRQ_IDE0, - .flags = IORESOURCE_IRQ, - }, -}; - - -static struct platform_device anubis_device_ide1 = { - .name = "simtec-ide", - .id = 1, - .num_resources = ARRAY_SIZE(anubis_ide1_resource), - .resource = anubis_ide1_resource, -}; - -/* Standard Anubis devices */ - -static struct platform_device *anubis_devices[] __initdata = { - &s3c_device_usb, - &s3c_device_wdt, - &s3c_device_adc, - &s3c_device_i2c, - &s3c_device_rtc, - &s3c_device_nand, - &anubis_device_ide0, - &anubis_device_ide1, -}; - -static struct clk *anubis_clocks[] = { - &s3c24xx_dclk0, - &s3c24xx_dclk1, - &s3c24xx_clkout0, - &s3c24xx_clkout1, - &s3c24xx_uclk, -}; - -static struct s3c24xx_board anubis_board __initdata = { - .devices = anubis_devices, - .devices_count = ARRAY_SIZE(anubis_devices), - .clocks = anubis_clocks, - .clocks_count = ARRAY_SIZE(anubis_clocks), -}; - -static void __init anubis_map_io(void) -{ - /* initialise the clocks */ - - s3c24xx_dclk0.parent = NULL; - s3c24xx_dclk0.rate = 12*1000*1000; - - s3c24xx_dclk1.parent = NULL; - s3c24xx_dclk1.rate = 24*1000*1000; - - s3c24xx_clkout0.parent = &s3c24xx_dclk0; - s3c24xx_clkout1.parent = &s3c24xx_dclk1; - - s3c24xx_uclk.parent = &s3c24xx_clkout1; - - s3c_device_nand.dev.platform_data = &anubis_nand_info; - - s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc)); - s3c24xx_init_clocks(0); - s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs)); - s3c24xx_set_board(&anubis_board); - - /* ensure that the GPIO is setup */ - s3c2410_gpio_setpin(S3C2410_GPA0, 1); -} - -MACHINE_START(ANUBIS, "Simtec-Anubis") - /* Maintainer: Ben Dooks */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - .map_io = anubis_map_io, - .init_irq = s3c24xx_init_irq, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index b8b76757ec54..7b81296427eb 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -50,9 +50,9 @@ #include -#include "clock.h" -#include "devs.h" -#include "cpu.h" +#include +#include +#include #include "usb-simtec.h" #define COPYRIGHT ", (c) 2004-2005 Simtec Electronics" diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 15b625eae499..5af26e177966 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -38,10 +38,10 @@ #include #include -#include "clock.h" -#include "devs.h" -#include "cpu.h" -#include "pm.h" +#include +#include +#include +#include static struct map_desc h1940_iodesc[] __initdata = { [0] = { diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c index 0411e9adb54d..dbac7311f98f 100644 --- a/arch/arm/mach-s3c2410/mach-n30.c +++ b/arch/arm/mach-s3c2410/mach-n30.c @@ -38,10 +38,10 @@ #include #include -#include "s3c2410.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" +#include +#include +#include +#include static struct map_desc n30_iodesc[] __initdata = { /* nothing here yet */ diff --git a/arch/arm/mach-s3c2410/mach-nexcoder.c b/arch/arm/mach-s3c2410/mach-nexcoder.c deleted file mode 100644 index d6dfdad8c90b..000000000000 --- a/arch/arm/mach-s3c2410/mach-nexcoder.c +++ /dev/null @@ -1,158 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-nexcoder.c - * - * Copyright (c) 2004 Nex Vision - * Guillaume GOURAT - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * Modifications: - * 15-10-2004 GG Created initial version - * 12-03-2005 BJD Updated for release - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include - -#include -#include -#include - -#include -#include -#include -#include -#include - -//#include -#include -#include - -#include "s3c2410.h" -#include "s3c2440.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" - -static struct map_desc nexcoder_iodesc[] __initdata = { - /* nothing here yet */ -}; - -#define UCON S3C2410_UCON_DEFAULT -#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB -#define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE - -static struct s3c2410_uartcfg nexcoder_uartcfgs[] __initdata = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - }, - [1] = { - .hwport = 1, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - }, - [2] = { - .hwport = 2, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - } -}; - -/* NOR Flash on NexVision NexCoder 2440 board */ - -static struct resource nexcoder_nor_resource[] = { - [0] = { - .start = S3C2410_CS0, - .end = S3C2410_CS0 + (8*1024*1024) - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct map_info nexcoder_nor_map = { - .bankwidth = 2, -}; - -static struct platform_device nexcoder_device_nor = { - .name = "mtd-flash", - .id = -1, - .num_resources = ARRAY_SIZE(nexcoder_nor_resource), - .resource = nexcoder_nor_resource, - .dev = - { - .platform_data = &nexcoder_nor_map, - } -}; - -/* Standard Nexcoder devices */ - -static struct platform_device *nexcoder_devices[] __initdata = { - &s3c_device_usb, - &s3c_device_lcd, - &s3c_device_wdt, - &s3c_device_i2c, - &s3c_device_iis, - &s3c_device_rtc, - &s3c_device_camif, - &s3c_device_spi0, - &s3c_device_spi1, - &nexcoder_device_nor, -}; - -static struct s3c24xx_board nexcoder_board __initdata = { - .devices = nexcoder_devices, - .devices_count = ARRAY_SIZE(nexcoder_devices), -}; - - -static void __init nexcoder_sensorboard_init(void) -{ - // Initialize SCCB bus - s3c2410_gpio_setpin(S3C2410_GPE14, 1); // IICSCL - s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_OUTP); - s3c2410_gpio_setpin(S3C2410_GPE15, 1); // IICSDA - s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_OUTP); - - // Power up the sensor board - s3c2410_gpio_setpin(S3C2410_GPF1, 1); - s3c2410_gpio_cfgpin(S3C2410_GPF1, S3C2410_GPF1_OUTP); // CAM_GPIO7 => nLDO_PWRDN - s3c2410_gpio_setpin(S3C2410_GPF2, 0); - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP); // CAM_GPIO6 => CAM_PWRDN -} - -static void __init nexcoder_map_io(void) -{ - s3c24xx_init_io(nexcoder_iodesc, ARRAY_SIZE(nexcoder_iodesc)); - s3c24xx_init_clocks(0); - s3c24xx_init_uarts(nexcoder_uartcfgs, ARRAY_SIZE(nexcoder_uartcfgs)); - s3c24xx_set_board(&nexcoder_board); - nexcoder_sensorboard_init(); -} - - -MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440") - /* Maintainer: Guillaume GOURAT */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - .map_io = nexcoder_map_io, - .init_irq = s3c24xx_init_irq, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-osiris.c b/arch/arm/mach-s3c2410/mach-osiris.c deleted file mode 100644 index 37b40850c9b9..000000000000 --- a/arch/arm/mach-s3c2410/mach-osiris.c +++ /dev/null @@ -1,303 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-osiris.c - * - * Copyright (c) 2005 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include -#include -#include -#include - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include "clock.h" -#include "devs.h" -#include "cpu.h" - -/* onboard perihpheral map */ - -static struct map_desc osiris_iodesc[] __initdata = { - /* ISA IO areas (may be over-written later) */ - - { - .virtual = (u32)S3C24XX_VA_ISA_BYTE, - .pfn = __phys_to_pfn(S3C2410_CS5), - .length = SZ_16M, - .type = MT_DEVICE, - }, { - .virtual = (u32)S3C24XX_VA_ISA_WORD, - .pfn = __phys_to_pfn(S3C2410_CS5), - .length = SZ_16M, - .type = MT_DEVICE, - }, - - /* CPLD control registers */ - - { - .virtual = (u32)OSIRIS_VA_CTRL1, - .pfn = __phys_to_pfn(OSIRIS_PA_CTRL1), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = (u32)OSIRIS_VA_CTRL2, - .pfn = __phys_to_pfn(OSIRIS_PA_CTRL2), - .length = SZ_16K, - .type = MT_DEVICE, - }, -}; - -#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK -#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB -#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE - -static struct s3c24xx_uart_clksrc osiris_serial_clocks[] = { - [0] = { - .name = "uclk", - .divisor = 1, - .min_baud = 0, - .max_baud = 0, - }, - [1] = { - .name = "pclk", - .divisor = 1, - .min_baud = 0, - .max_baud = 0, - } -}; - -static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - .clocks = osiris_serial_clocks, - .clocks_size = ARRAY_SIZE(osiris_serial_clocks), - }, - [1] = { - .hwport = 1, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - .clocks = osiris_serial_clocks, - .clocks_size = ARRAY_SIZE(osiris_serial_clocks), - }, - [2] = { - .hwport = 2, - .flags = 0, - .ucon = UCON, - .ulcon = ULCON, - .ufcon = UFCON, - .clocks = osiris_serial_clocks, - .clocks_size = ARRAY_SIZE(osiris_serial_clocks), - } -}; - -/* NAND Flash on Osiris board */ - -static int external_map[] = { 2 }; -static int chip0_map[] = { 0 }; -static int chip1_map[] = { 1 }; - -static struct mtd_partition osiris_default_nand_part[] = { - [0] = { - .name = "Boot Agent", - .size = SZ_16K, - .offset = 0, - }, - [1] = { - .name = "/boot", - .size = SZ_4M - SZ_16K, - .offset = SZ_16K, - }, - [2] = { - .name = "user1", - .offset = SZ_4M, - .size = SZ_32M - SZ_4M, - }, - [3] = { - .name = "user2", - .offset = SZ_32M, - .size = MTDPART_SIZ_FULL, - } -}; - -/* the Osiris has 3 selectable slots for nand-flash, the two - * on-board chip areas, as well as the external slot. - * - * Note, there is no current hot-plug support for the External - * socket. -*/ - -static struct s3c2410_nand_set osiris_nand_sets[] = { - [1] = { - .name = "External", - .nr_chips = 1, - .nr_map = external_map, - .nr_partitions = ARRAY_SIZE(osiris_default_nand_part), - .partitions = osiris_default_nand_part, - }, - [0] = { - .name = "chip0", - .nr_chips = 1, - .nr_map = chip0_map, - .nr_partitions = ARRAY_SIZE(osiris_default_nand_part), - .partitions = osiris_default_nand_part, - }, - [2] = { - .name = "chip1", - .nr_chips = 1, - .nr_map = chip1_map, - .nr_partitions = ARRAY_SIZE(osiris_default_nand_part), - .partitions = osiris_default_nand_part, - }, -}; - -static void osiris_nand_select(struct s3c2410_nand_set *set, int slot) -{ - unsigned int tmp; - - slot = set->nr_map[slot] & 3; - - pr_debug("osiris_nand: selecting slot %d (set %p,%p)\n", - slot, set, set->nr_map); - - tmp = __raw_readb(OSIRIS_VA_CTRL1); - tmp &= ~OSIRIS_CTRL1_NANDSEL; - tmp |= slot; - - pr_debug("osiris_nand: ctrl1 now %02x\n", tmp); - - __raw_writeb(tmp, OSIRIS_VA_CTRL1); -} - -static struct s3c2410_platform_nand osiris_nand_info = { - .tacls = 25, - .twrph0 = 60, - .twrph1 = 60, - .nr_sets = ARRAY_SIZE(osiris_nand_sets), - .sets = osiris_nand_sets, - .select_chip = osiris_nand_select, -}; - -/* PCMCIA control and configuration */ - -static struct resource osiris_pcmcia_resource[] = { - [0] = { - .start = 0x0f000000, - .end = 0x0f100000, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = 0x0c000000, - .end = 0x0c100000, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device osiris_pcmcia = { - .name = "osiris-pcmcia", - .id = -1, - .num_resources = ARRAY_SIZE(osiris_pcmcia_resource), - .resource = osiris_pcmcia_resource, -}; - -/* Standard Osiris devices */ - -static struct platform_device *osiris_devices[] __initdata = { - &s3c_device_i2c, - &s3c_device_nand, - &osiris_pcmcia, -}; - -static struct clk *osiris_clocks[] = { - &s3c24xx_dclk0, - &s3c24xx_dclk1, - &s3c24xx_clkout0, - &s3c24xx_clkout1, - &s3c24xx_uclk, -}; - -static struct s3c24xx_board osiris_board __initdata = { - .devices = osiris_devices, - .devices_count = ARRAY_SIZE(osiris_devices), - .clocks = osiris_clocks, - .clocks_count = ARRAY_SIZE(osiris_clocks), -}; - -static void __init osiris_map_io(void) -{ - unsigned long flags; - - /* initialise the clocks */ - - s3c24xx_dclk0.parent = NULL; - s3c24xx_dclk0.rate = 12*1000*1000; - - s3c24xx_dclk1.parent = NULL; - s3c24xx_dclk1.rate = 24*1000*1000; - - s3c24xx_clkout0.parent = &s3c24xx_dclk0; - s3c24xx_clkout1.parent = &s3c24xx_dclk1; - - s3c24xx_uclk.parent = &s3c24xx_clkout1; - - s3c_device_nand.dev.platform_data = &osiris_nand_info; - - s3c24xx_init_io(osiris_iodesc, ARRAY_SIZE(osiris_iodesc)); - s3c24xx_init_clocks(0); - s3c24xx_init_uarts(osiris_uartcfgs, ARRAY_SIZE(osiris_uartcfgs)); - s3c24xx_set_board(&osiris_board); - - /* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */ - - local_irq_save(flags); - __raw_writel(__raw_readl(S3C2410_BWSCON) | S3C2410_BWSCON_ST1 | S3C2410_BWSCON_ST2 | S3C2410_BWSCON_ST3 | S3C2410_BWSCON_ST4 | S3C2410_BWSCON_ST5, S3C2410_BWSCON); - local_irq_restore(flags); - - /* write-protect line to the NAND */ - s3c2410_gpio_setpin(S3C2410_GPA0, 1); -} - -MACHINE_START(OSIRIS, "Simtec-OSIRIS") - /* Maintainer: Ben Dooks */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - .map_io = osiris_map_io, - .init_irq = s3c24xx_init_irq, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-otom.c b/arch/arm/mach-s3c2410/mach-otom.c index 2c738b375e4d..c78ab75b44f3 100644 --- a/arch/arm/mach-s3c2410/mach-otom.c +++ b/arch/arm/mach-s3c2410/mach-otom.c @@ -32,10 +32,10 @@ #include #include -#include "s3c2410.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" +#include +#include +#include +#include static struct map_desc otom11_iodesc[] __initdata = { /* Device area */ diff --git a/arch/arm/mach-s3c2410/mach-rx3715.c b/arch/arm/mach-s3c2410/mach-rx3715.c deleted file mode 100644 index ecbcdf79d739..000000000000 --- a/arch/arm/mach-s3c2410/mach-rx3715.c +++ /dev/null @@ -1,244 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-rx3715.c - * - * Copyright (c) 2003,2004 Simtec Electronics - * Ben Dooks - * - * http://www.handhelds.org/projects/rx3715.html - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "clock.h" -#include "devs.h" -#include "cpu.h" -#include "pm.h" - -static struct map_desc rx3715_iodesc[] __initdata = { - /* dump ISA space somewhere unused */ - - { - .virtual = (u32)S3C24XX_VA_ISA_WORD, - .pfn = __phys_to_pfn(S3C2410_CS3), - .length = SZ_1M, - .type = MT_DEVICE, - }, { - .virtual = (u32)S3C24XX_VA_ISA_BYTE, - .pfn = __phys_to_pfn(S3C2410_CS3), - .length = SZ_1M, - .type = MT_DEVICE, - }, -}; - - -static struct s3c24xx_uart_clksrc rx3715_serial_clocks[] = { - [0] = { - .name = "fclk", - .divisor = 0, - .min_baud = 0, - .max_baud = 0, - } -}; - -static struct s3c2410_uartcfg rx3715_uartcfgs[] = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - .clocks = rx3715_serial_clocks, - .clocks_size = ARRAY_SIZE(rx3715_serial_clocks), - }, - [1] = { - .hwport = 1, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x00, - .clocks = rx3715_serial_clocks, - .clocks_size = ARRAY_SIZE(rx3715_serial_clocks), - }, - /* IR port */ - [2] = { - .hwport = 2, - .uart_flags = UPF_CONS_FLOW, - .ucon = 0x3c5, - .ulcon = 0x43, - .ufcon = 0x51, - .clocks = rx3715_serial_clocks, - .clocks_size = ARRAY_SIZE(rx3715_serial_clocks), - } -}; - -/* framebuffer lcd controller information */ - -static struct s3c2410fb_mach_info rx3715_lcdcfg __initdata = { - .regs = { - .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | \ - S3C2410_LCDCON1_TFT | \ - S3C2410_LCDCON1_CLKVAL(0x0C), - - .lcdcon2 = S3C2410_LCDCON2_VBPD(5) | \ - S3C2410_LCDCON2_LINEVAL(319) | \ - S3C2410_LCDCON2_VFPD(6) | \ - S3C2410_LCDCON2_VSPW(2), - - .lcdcon3 = S3C2410_LCDCON3_HBPD(35) | \ - S3C2410_LCDCON3_HOZVAL(239) | \ - S3C2410_LCDCON3_HFPD(35), - - .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | \ - S3C2410_LCDCON4_HSPW(7), - - .lcdcon5 = S3C2410_LCDCON5_INVVLINE | - S3C2410_LCDCON5_FRM565 | - S3C2410_LCDCON5_HWSWP, - }, - - .lpcsel = 0xf82, - - .gpccon = 0xaa955699, - .gpccon_mask = 0xffc003cc, - .gpcup = 0x0000ffff, - .gpcup_mask = 0xffffffff, - - .gpdcon = 0xaa95aaa1, - .gpdcon_mask = 0xffc0fff0, - .gpdup = 0x0000faff, - .gpdup_mask = 0xffffffff, - - .fixed_syncs = 1, - .width = 240, - .height = 320, - - .xres = { - .min = 240, - .max = 240, - .defval = 240, - }, - - .yres = { - .max = 320, - .min = 320, - .defval = 320, - }, - - .bpp = { - .min = 16, - .max = 16, - .defval = 16, - }, -}; - -static struct mtd_partition rx3715_nand_part[] = { - [0] = { - .name = "Whole Flash", - .offset = 0, - .size = MTDPART_SIZ_FULL, - .mask_flags = MTD_WRITEABLE, - } -}; - -static struct s3c2410_nand_set rx3715_nand_sets[] = { - [0] = { - .name = "Internal", - .nr_chips = 1, - .nr_partitions = ARRAY_SIZE(rx3715_nand_part), - .partitions = rx3715_nand_part, - }, -}; - -static struct s3c2410_platform_nand rx3715_nand_info = { - .tacls = 25, - .twrph0 = 50, - .twrph1 = 15, - .nr_sets = ARRAY_SIZE(rx3715_nand_sets), - .sets = rx3715_nand_sets, -}; - -static struct platform_device *rx3715_devices[] __initdata = { - &s3c_device_usb, - &s3c_device_lcd, - &s3c_device_wdt, - &s3c_device_i2c, - &s3c_device_iis, - &s3c_device_nand, -}; - -static struct s3c24xx_board rx3715_board __initdata = { - .devices = rx3715_devices, - .devices_count = ARRAY_SIZE(rx3715_devices) -}; - -static void __init rx3715_map_io(void) -{ - s3c_device_nand.dev.platform_data = &rx3715_nand_info; - - s3c24xx_init_io(rx3715_iodesc, ARRAY_SIZE(rx3715_iodesc)); - s3c24xx_init_clocks(16934000); - s3c24xx_init_uarts(rx3715_uartcfgs, ARRAY_SIZE(rx3715_uartcfgs)); - s3c24xx_set_board(&rx3715_board); -} - -static void __init rx3715_init_irq(void) -{ - s3c24xx_init_irq(); -} - -static void __init rx3715_init_machine(void) -{ - memcpy(phys_to_virt(H1940_SUSPEND_RESUMEAT), h1940_pm_return, 1024); - s3c2410_pm_init(); - - s3c24xx_fb_set_platdata(&rx3715_lcdcfg); -} - - -MACHINE_START(RX3715, "IPAQ-RX3715") - /* Maintainer: Ben Dooks */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - .map_io = rx3715_map_io, - .init_irq = rx3715_init_irq, - .init_machine = rx3715_init_machine, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c index 01c0c986d827..57b8a80f33d0 100644 --- a/arch/arm/mach-s3c2410/mach-smdk2410.c +++ b/arch/arm/mach-s3c2410/mach-smdk2410.c @@ -1,4 +1,4 @@ -/*********************************************************************** +/* linux/arch/arm/mach-s3c2410/mach-smdk2410.c * * linux/arch/arm/mach-s3c2410/mach-smdk2410.c * @@ -49,10 +49,10 @@ #include -#include "devs.h" -#include "cpu.h" +#include +#include -#include "common-smdk.h" +#include static struct map_desc smdk2410_iodesc[] __initdata = { /* nothing here yet */ diff --git a/arch/arm/mach-s3c2410/mach-smdk2413.c b/arch/arm/mach-s3c2410/mach-smdk2413.c deleted file mode 100644 index 4f89abd7a6df..000000000000 --- a/arch/arm/mach-s3c2410/mach-smdk2413.c +++ /dev/null @@ -1,140 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-smdk2413.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * Thanks to Dimity Andric (TomTom) and Steven Ryu (Samsung) for the - * loans of SMDK2413 to work with. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include -#include -#include - -//#include -#include -#include -#include - -#include -#include - -#include "s3c2410.h" -#include "s3c2412.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" - -#include "common-smdk.h" - -static struct map_desc smdk2413_iodesc[] __initdata = { -}; - -static struct s3c2410_uartcfg smdk2413_uartcfgs[] __initdata = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - }, - [1] = { - .hwport = 1, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - }, - /* IR port */ - [2] = { - .hwport = 2, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x43, - .ufcon = 0x51, - } -}; - -static struct platform_device *smdk2413_devices[] __initdata = { - &s3c_device_usb, - //&s3c_device_lcd, - &s3c_device_wdt, - &s3c_device_i2c, - &s3c_device_iis, -}; - -static struct s3c24xx_board smdk2413_board __initdata = { - .devices = smdk2413_devices, - .devices_count = ARRAY_SIZE(smdk2413_devices) -}; - -static void __init smdk2413_fixup(struct machine_desc *desc, - struct tag *tags, char **cmdline, - struct meminfo *mi) -{ - if (tags != phys_to_virt(S3C2410_SDRAM_PA + 0x100)) { - mi->nr_banks=1; - mi->bank[0].start = 0x30000000; - mi->bank[0].size = SZ_64M; - mi->bank[0].node = 0; - } -} - -static void __init smdk2413_map_io(void) -{ - s3c24xx_init_io(smdk2413_iodesc, ARRAY_SIZE(smdk2413_iodesc)); - s3c24xx_init_clocks(12000000); - s3c24xx_init_uarts(smdk2413_uartcfgs, ARRAY_SIZE(smdk2413_uartcfgs)); - s3c24xx_set_board(&smdk2413_board); -} - -static void __init smdk2413_machine_init(void) -{ - smdk_machine_init(); -} - -MACHINE_START(S3C2413, "S3C2413") - /* Maintainer: Ben Dooks */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - - .fixup = smdk2413_fixup, - .init_irq = s3c24xx_init_irq, - .map_io = smdk2413_map_io, - .init_machine = smdk2413_machine_init, - .timer = &s3c24xx_timer, -MACHINE_END - -MACHINE_START(SMDK2413, "SMDK2413") - /* Maintainer: Ben Dooks */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - - .fixup = smdk2413_fixup, - .init_irq = s3c24xx_init_irq, - .map_io = smdk2413_map_io, - .init_machine = smdk2413_machine_init, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-smdk2440.c b/arch/arm/mach-s3c2410/mach-smdk2440.c deleted file mode 100644 index 2b61f4ed1da4..000000000000 --- a/arch/arm/mach-s3c2410/mach-smdk2440.c +++ /dev/null @@ -1,208 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-smdk2440.c - * - * Copyright (c) 2004,2005 Simtec Electronics - * Ben Dooks - * - * http://www.fluff.org/ben/smdk2440/ - * - * Thanks to Dimity Andric and TomTom for the loan of an SMDK2440. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include -#include - -//#include -#include -#include -#include - -#include -#include - -#include "s3c2410.h" -#include "s3c2440.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" - -#include "common-smdk.h" - -static struct map_desc smdk2440_iodesc[] __initdata = { - /* ISA IO Space map (memory space selected by A24) */ - - { - .virtual = (u32)S3C24XX_VA_ISA_WORD, - .pfn = __phys_to_pfn(S3C2410_CS2), - .length = 0x10000, - .type = MT_DEVICE, - }, { - .virtual = (u32)S3C24XX_VA_ISA_WORD + 0x10000, - .pfn = __phys_to_pfn(S3C2410_CS2 + (1<<24)), - .length = SZ_4M, - .type = MT_DEVICE, - }, { - .virtual = (u32)S3C24XX_VA_ISA_BYTE, - .pfn = __phys_to_pfn(S3C2410_CS2), - .length = 0x10000, - .type = MT_DEVICE, - }, { - .virtual = (u32)S3C24XX_VA_ISA_BYTE + 0x10000, - .pfn = __phys_to_pfn(S3C2410_CS2 + (1<<24)), - .length = SZ_4M, - .type = MT_DEVICE, - } -}; - -#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK -#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB -#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE - -static struct s3c2410_uartcfg smdk2440_uartcfgs[] __initdata = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - }, - [1] = { - .hwport = 1, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - }, - /* IR port */ - [2] = { - .hwport = 2, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x43, - .ufcon = 0x51, - } -}; - -/* LCD driver info */ - -static struct s3c2410fb_mach_info smdk2440_lcd_cfg __initdata = { - .regs = { - - .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | - S3C2410_LCDCON1_TFT | - S3C2410_LCDCON1_CLKVAL(0x04), - - .lcdcon2 = S3C2410_LCDCON2_VBPD(7) | - S3C2410_LCDCON2_LINEVAL(319) | - S3C2410_LCDCON2_VFPD(6) | - S3C2410_LCDCON2_VSPW(3), - - .lcdcon3 = S3C2410_LCDCON3_HBPD(19) | - S3C2410_LCDCON3_HOZVAL(239) | - S3C2410_LCDCON3_HFPD(7), - - .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | - S3C2410_LCDCON4_HSPW(3), - - .lcdcon5 = S3C2410_LCDCON5_FRM565 | - S3C2410_LCDCON5_INVVLINE | - S3C2410_LCDCON5_INVVFRAME | - S3C2410_LCDCON5_PWREN | - S3C2410_LCDCON5_HWSWP, - }, - -#if 0 - /* currently setup by downloader */ - .gpccon = 0xaa940659, - .gpccon_mask = 0xffffffff, - .gpcup = 0x0000ffff, - .gpcup_mask = 0xffffffff, - .gpdcon = 0xaa84aaa0, - .gpdcon_mask = 0xffffffff, - .gpdup = 0x0000faff, - .gpdup_mask = 0xffffffff, -#endif - - .lpcsel = ((0xCE6) & ~7) | 1<<4, - - .width = 240, - .height = 320, - - .xres = { - .min = 240, - .max = 240, - .defval = 240, - }, - - .yres = { - .min = 320, - .max = 320, - .defval = 320, - }, - - .bpp = { - .min = 16, - .max = 16, - .defval = 16, - }, -}; - -static struct platform_device *smdk2440_devices[] __initdata = { - &s3c_device_usb, - &s3c_device_lcd, - &s3c_device_wdt, - &s3c_device_i2c, - &s3c_device_iis, -}; - -static struct s3c24xx_board smdk2440_board __initdata = { - .devices = smdk2440_devices, - .devices_count = ARRAY_SIZE(smdk2440_devices) -}; - -static void __init smdk2440_map_io(void) -{ - s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc)); - s3c24xx_init_clocks(16934400); - s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs)); - s3c24xx_set_board(&smdk2440_board); -} - -static void __init smdk2440_machine_init(void) -{ - s3c24xx_fb_set_platdata(&smdk2440_lcd_cfg); - - smdk_machine_init(); -} - -MACHINE_START(S3C2440, "SMDK2440") - /* Maintainer: Ben Dooks */ - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - - .init_irq = s3c24xx_init_irq, - .map_io = smdk2440_map_io, - .init_machine = smdk2440_machine_init, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index a382fc095110..c947c75bcbf0 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -43,9 +43,9 @@ #include #include -#include "clock.h" -#include "devs.h" -#include "cpu.h" +#include +#include +#include #include "usb-simtec.h" /* macros for virtual address mods for the io space entries */ diff --git a/arch/arm/mach-s3c2410/mach-vstms.c b/arch/arm/mach-s3c2410/mach-vstms.c deleted file mode 100644 index 0360e1055bcd..000000000000 --- a/arch/arm/mach-s3c2410/mach-vstms.c +++ /dev/null @@ -1,169 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/mach-vstms.c - * - * (C) 2006 Thomas Gleixner - * - * Derived from mach-smdk2413.c - (C) 2006 Simtec Electronics - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include - -#include "s3c2410.h" -#include "s3c2412.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" - - -static struct map_desc vstms_iodesc[] __initdata = { -}; - -static struct s3c2410_uartcfg vstms_uartcfgs[] __initdata = { - [0] = { - .hwport = 0, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - }, - [1] = { - .hwport = 1, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - }, - [2] = { - .hwport = 2, - .flags = 0, - .ucon = 0x3c5, - .ulcon = 0x03, - .ufcon = 0x51, - } -}; - -static struct mtd_partition vstms_nand_part[] = { - [0] = { - .name = "Boot Agent", - .size = 0x7C000, - .offset = 0, - }, - [1] = { - .name = "UBoot Config", - .offset = 0x7C000, - .size = 0x4000, - }, - [2] = { - .name = "Kernel", - .offset = 0x80000, - .size = 0x200000, - }, - [3] = { - .name = "RFS", - .offset = 0x280000, - .size = 0x3d80000, - }, -}; - -static struct s3c2410_nand_set vstms_nand_sets[] = { - [0] = { - .name = "NAND", - .nr_chips = 1, - .nr_partitions = ARRAY_SIZE(vstms_nand_part), - .partitions = vstms_nand_part, - }, -}; - -/* choose a set of timings which should suit most 512Mbit - * chips and beyond. -*/ - -static struct s3c2410_platform_nand vstms_nand_info = { - .tacls = 20, - .twrph0 = 60, - .twrph1 = 20, - .nr_sets = ARRAY_SIZE(vstms_nand_sets), - .sets = vstms_nand_sets, -}; - -static struct platform_device *vstms_devices[] __initdata = { - &s3c_device_usb, - &s3c_device_wdt, - &s3c_device_i2c, - &s3c_device_iis, - &s3c_device_rtc, - &s3c_device_nand, -}; - -static struct s3c24xx_board vstms_board __initdata = { - .devices = vstms_devices, - .devices_count = ARRAY_SIZE(vstms_devices) -}; - -static void __init vstms_fixup(struct machine_desc *desc, - struct tag *tags, char **cmdline, - struct meminfo *mi) -{ - if (tags != phys_to_virt(S3C2410_SDRAM_PA + 0x100)) { - mi->nr_banks=1; - mi->bank[0].start = 0x30000000; - mi->bank[0].size = SZ_64M; - mi->bank[0].node = 0; - } -} - -static void __init vstms_map_io(void) -{ - s3c_device_nand.dev.platform_data = &vstms_nand_info; - - s3c24xx_init_io(vstms_iodesc, ARRAY_SIZE(vstms_iodesc)); - s3c24xx_init_clocks(12000000); - s3c24xx_init_uarts(vstms_uartcfgs, ARRAY_SIZE(vstms_uartcfgs)); - s3c24xx_set_board(&vstms_board); -} - -MACHINE_START(VSTMS, "VSTMS") - .phys_io = S3C2410_PA_UART, - .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, - .boot_params = S3C2410_SDRAM_PA + 0x100, - - .fixup = vstms_fixup, - .init_irq = s3c24xx_init_irq, - .map_io = vstms_map_io, - .timer = &s3c24xx_timer, -MACHINE_END diff --git a/arch/arm/mach-s3c2410/pm-simtec.c b/arch/arm/mach-s3c2410/pm-simtec.c deleted file mode 100644 index 619133eb7168..000000000000 --- a/arch/arm/mach-s3c2410/pm-simtec.c +++ /dev/null @@ -1,66 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/pm-simtec.c - * - * Copyright (c) 2004 Simtec Electronics - * Ben Dooks - * - * http://armlinux.simtec.co.uk/ - * - * Power Management helpers for Simtec S3C24XX implementations - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include -#include - -#include -#include -#include - -#include - -#include "pm.h" - -#define COPYRIGHT ", (c) 2005 Simtec Electronics" - -/* pm_simtec_init - * - * enable the power management functions -*/ - -static __init int pm_simtec_init(void) -{ - unsigned long gstatus4; - - /* check which machine we are running on */ - - if (!machine_is_bast() && !machine_is_vr1000() && - !machine_is_anubis() && !machine_is_osiris() && - !machine_is_aml_m5900()) - return 0; - - printk(KERN_INFO "Simtec Board Power Manangement" COPYRIGHT "\n"); - - gstatus4 = (__raw_readl(S3C2410_BANKCON7) & 0x3) << 30; - gstatus4 |= (__raw_readl(S3C2410_BANKCON6) & 0x3) << 28; - gstatus4 |= (__raw_readl(S3C2410_BANKSIZE) & S3C2410_BANKSIZE_MASK); - - __raw_writel(gstatus4, S3C2410_GSTATUS4); - - return s3c2410_pm_init(); -} - -arch_initcall(pm_simtec_init); diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c index ebf294dd31da..3b3a7db4e0dd 100644 --- a/arch/arm/mach-s3c2410/pm.c +++ b/arch/arm/mach-s3c2410/pm.c @@ -1,11 +1,9 @@ /* linux/arch/arm/mach-s3c2410/pm.c * - * Copyright (c) 2004,2006 Simtec Electronics + * Copyright (c) 2006 Simtec Electronics * Ben Dooks * - * S3C24XX Power Manager (Suspend-To-RAM) support - * - * See Documentation/arm/Samsung-S3C24XX/Suspend.txt for more information + * S3C2410 (and compatible) Power Manager (Suspend-To-RAM) support * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -20,640 +18,139 @@ * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * Parts based on arch/arm/mach-pxa/pm.c - * - * Thanks to Dimitry Andric for debugging */ #include #include #include #include -#include -#include -#include -#include -#include +#include -#include #include #include -#include -#include -#include -#include -#include - -#include - -#include "pm.h" - -/* for external use */ - -unsigned long s3c_pm_flags; - -#define PFX "s3c24xx-pm: " - -static struct sleep_save core_save[] = { - SAVE_ITEM(S3C2410_LOCKTIME), - SAVE_ITEM(S3C2410_CLKCON), - - /* we restore the timings here, with the proviso that the board - * brings the system up in an slower, or equal frequency setting - * to the original system. - * - * if we cannot guarantee this, then things are going to go very - * wrong here, as we modify the refresh and both pll settings. - */ - - SAVE_ITEM(S3C2410_BWSCON), - SAVE_ITEM(S3C2410_BANKCON0), - SAVE_ITEM(S3C2410_BANKCON1), - SAVE_ITEM(S3C2410_BANKCON2), - SAVE_ITEM(S3C2410_BANKCON3), - SAVE_ITEM(S3C2410_BANKCON4), - SAVE_ITEM(S3C2410_BANKCON5), - - SAVE_ITEM(S3C2410_CLKDIVN), - SAVE_ITEM(S3C2410_MPLLCON), - SAVE_ITEM(S3C2410_UPLLCON), - SAVE_ITEM(S3C2410_CLKSLOW), - SAVE_ITEM(S3C2410_REFRESH), -}; - -static struct sleep_save gpio_save[] = { - SAVE_ITEM(S3C2410_GPACON), - SAVE_ITEM(S3C2410_GPADAT), - - SAVE_ITEM(S3C2410_GPBCON), - SAVE_ITEM(S3C2410_GPBDAT), - SAVE_ITEM(S3C2410_GPBUP), - - SAVE_ITEM(S3C2410_GPCCON), - SAVE_ITEM(S3C2410_GPCDAT), - SAVE_ITEM(S3C2410_GPCUP), - - SAVE_ITEM(S3C2410_GPDCON), - SAVE_ITEM(S3C2410_GPDDAT), - SAVE_ITEM(S3C2410_GPDUP), - - SAVE_ITEM(S3C2410_GPECON), - SAVE_ITEM(S3C2410_GPEDAT), - SAVE_ITEM(S3C2410_GPEUP), - - SAVE_ITEM(S3C2410_GPFCON), - SAVE_ITEM(S3C2410_GPFDAT), - SAVE_ITEM(S3C2410_GPFUP), +#include - SAVE_ITEM(S3C2410_GPGCON), - SAVE_ITEM(S3C2410_GPGDAT), - SAVE_ITEM(S3C2410_GPGUP), - - SAVE_ITEM(S3C2410_GPHCON), - SAVE_ITEM(S3C2410_GPHDAT), - SAVE_ITEM(S3C2410_GPHUP), +#include +#include - SAVE_ITEM(S3C2410_DCLKCON), -}; +#include +#include #ifdef CONFIG_S3C2410_PM_DEBUG - -#define SAVE_UART(va) \ - SAVE_ITEM((va) + S3C2410_ULCON), \ - SAVE_ITEM((va) + S3C2410_UCON), \ - SAVE_ITEM((va) + S3C2410_UFCON), \ - SAVE_ITEM((va) + S3C2410_UMCON), \ - SAVE_ITEM((va) + S3C2410_UBRDIV) - -static struct sleep_save uart_save[] = { - SAVE_UART(S3C24XX_VA_UART0), - SAVE_UART(S3C24XX_VA_UART1), -#ifndef CONFIG_CPU_S3C2400 - SAVE_UART(S3C24XX_VA_UART2), -#endif -}; - -/* debug - * - * we send the debug to printascii() to allow it to be seen if the - * system never wakes up from the sleep -*/ - -extern void printascii(const char *); - -void pm_dbg(const char *fmt, ...) -{ - va_list va; - char buff[256]; - - va_start(va, fmt); - vsprintf(buff, fmt, va); - va_end(va); - - printascii(buff); -} - -static void s3c2410_pm_debug_init(void) -{ - unsigned long tmp = __raw_readl(S3C2410_CLKCON); - - /* re-start uart clocks */ - tmp |= S3C2410_CLKCON_UART0; - tmp |= S3C2410_CLKCON_UART1; - tmp |= S3C2410_CLKCON_UART2; - - __raw_writel(tmp, S3C2410_CLKCON); - udelay(10); -} - +extern void pm_dbg(const char *fmt, ...); #define DBG(fmt...) pm_dbg(fmt) #else #define DBG(fmt...) printk(KERN_DEBUG fmt) - -#define s3c2410_pm_debug_init() do { } while(0) - -static struct sleep_save uart_save[] = {}; #endif -#if defined(CONFIG_S3C2410_PM_CHECK) && CONFIG_S3C2410_PM_CHECK_CHUNKSIZE != 0 - -/* suspend checking code... - * - * this next area does a set of crc checks over all the installed - * memory, so the system can verify if the resume was ok. - * - * CONFIG_S3C2410_PM_CHECK_CHUNKSIZE defines the block-size for the CRC, - * increasing it will mean that the area corrupted will be less easy to spot, - * and reducing the size will cause the CRC save area to grow -*/ - -#define CHECK_CHUNKSIZE (CONFIG_S3C2410_PM_CHECK_CHUNKSIZE * 1024) - -static u32 crc_size; /* size needed for the crc block */ -static u32 *crcs; /* allocated over suspend/resume */ - -typedef u32 *(run_fn_t)(struct resource *ptr, u32 *arg); - -/* s3c2410_pm_run_res - * - * go thorugh the given resource list, and look for system ram -*/ - -static void s3c2410_pm_run_res(struct resource *ptr, run_fn_t fn, u32 *arg) -{ - while (ptr != NULL) { - if (ptr->child != NULL) - s3c2410_pm_run_res(ptr->child, fn, arg); - - if ((ptr->flags & IORESOURCE_MEM) && - strcmp(ptr->name, "System RAM") == 0) { - DBG("Found system RAM at %08lx..%08lx\n", - ptr->start, ptr->end); - arg = (fn)(ptr, arg); - } - - ptr = ptr->sibling; - } -} - -static void s3c2410_pm_run_sysram(run_fn_t fn, u32 *arg) -{ - s3c2410_pm_run_res(&iomem_resource, fn, arg); -} - -static u32 *s3c2410_pm_countram(struct resource *res, u32 *val) -{ - u32 size = (u32)(res->end - res->start)+1; - - size += CHECK_CHUNKSIZE-1; - size /= CHECK_CHUNKSIZE; - - DBG("Area %08lx..%08lx, %d blocks\n", res->start, res->end, size); - - *val += size * sizeof(u32); - return val; -} - -/* s3c2410_pm_prepare_check - * - * prepare the necessary information for creating the CRCs. This - * must be done before the final save, as it will require memory - * allocating, and thus touching bits of the kernel we do not - * know about. -*/ - -static void s3c2410_pm_check_prepare(void) +static void s3c2410_pm_prepare(void) { - crc_size = 0; + /* ensure at least GSTATUS3 has the resume address */ - s3c2410_pm_run_sysram(s3c2410_pm_countram, &crc_size); + __raw_writel(virt_to_phys(s3c2410_cpu_resume), S3C2410_GSTATUS3); - DBG("s3c2410_pm_prepare_check: %u checks needed\n", crc_size); + DBG("GSTATUS3 0x%08x\n", __raw_readl(S3C2410_GSTATUS3)); + DBG("GSTATUS4 0x%08x\n", __raw_readl(S3C2410_GSTATUS4)); - crcs = kmalloc(crc_size+4, GFP_KERNEL); - if (crcs == NULL) - printk(KERN_ERR "Cannot allocated CRC save area\n"); -} + if (machine_is_h1940()) { + void *base = phys_to_virt(H1940_SUSPEND_CHECK); + unsigned long ptr; + unsigned long calc = 0; -static u32 *s3c2410_pm_makecheck(struct resource *res, u32 *val) -{ - unsigned long addr, left; + /* generate check for the bootloader to check on resume */ - for (addr = res->start; addr < res->end; - addr += CHECK_CHUNKSIZE) { - left = res->end - addr; + for (ptr = 0; ptr < 0x40000; ptr += 0x400) + calc += __raw_readl(base+ptr); - if (left > CHECK_CHUNKSIZE) - left = CHECK_CHUNKSIZE; - - *val = crc32_le(~0, phys_to_virt(addr), left); - val++; + __raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM)); } - return val; -} - -/* s3c2410_pm_check_store - * - * compute the CRC values for the memory blocks before the final - * sleep. -*/ - -static void s3c2410_pm_check_store(void) -{ - if (crcs != NULL) - s3c2410_pm_run_sysram(s3c2410_pm_makecheck, crcs); -} - -/* in_region - * - * return TRUE if the area defined by ptr..ptr+size contatins the - * what..what+whatsz -*/ - -static inline int in_region(void *ptr, int size, void *what, size_t whatsz) -{ - if ((what+whatsz) < ptr) - return 0; - - if (what > (ptr+size)) - return 0; - - return 1; -} - -static u32 *s3c2410_pm_runcheck(struct resource *res, u32 *val) -{ - void *save_at = phys_to_virt(s3c2410_sleep_save_phys); - unsigned long addr; - unsigned long left; - void *ptr; - u32 calc; - - for (addr = res->start; addr < res->end; - addr += CHECK_CHUNKSIZE) { - left = res->end - addr; + /* the RX3715 uses similar code and the same H1940 and the + * same offsets for resume and checksum pointers */ - if (left > CHECK_CHUNKSIZE) - left = CHECK_CHUNKSIZE; + if (machine_is_rx3715()) { + void *base = phys_to_virt(H1940_SUSPEND_CHECK); + unsigned long ptr; + unsigned long calc = 0; - ptr = phys_to_virt(addr); + /* generate check for the bootloader to check on resume */ - if (in_region(ptr, left, crcs, crc_size)) { - DBG("skipping %08lx, has crc block in\n", addr); - goto skip_check; - } + for (ptr = 0; ptr < 0x40000; ptr += 0x4) + calc += __raw_readl(base+ptr); - if (in_region(ptr, left, save_at, 32*4 )) { - DBG("skipping %08lx, has save block in\n", addr); - goto skip_check; - } - - /* calculate and check the checksum */ - - calc = crc32_le(~0, ptr, left); - if (calc != *val) { - printk(KERN_ERR PFX "Restore CRC error at " - "%08lx (%08x vs %08x)\n", addr, calc, *val); - - DBG("Restore CRC error at %08lx (%08x vs %08x)\n", - addr, calc, *val); - } - - skip_check: - val++; + __raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM)); } - return val; -} + if ( machine_is_aml_m5900() ) + s3c2410_gpio_setpin(S3C2410_GPF2, 1); -/* s3c2410_pm_check_restore - * - * check the CRCs after the restore event and free the memory used - * to hold them -*/ - -static void s3c2410_pm_check_restore(void) -{ - if (crcs != NULL) { - s3c2410_pm_run_sysram(s3c2410_pm_runcheck, crcs); - kfree(crcs); - crcs = NULL; - } } -#else - -#define s3c2410_pm_check_prepare() do { } while(0) -#define s3c2410_pm_check_restore() do { } while(0) -#define s3c2410_pm_check_store() do { } while(0) -#endif - -/* helper functions to save and restore register state */ - -void s3c2410_pm_do_save(struct sleep_save *ptr, int count) +static int s3c2410_pm_resume(struct sys_device *dev) { - for (; count > 0; count--, ptr++) { - ptr->val = __raw_readl(ptr->reg); - DBG("saved %p value %08lx\n", ptr->reg, ptr->val); - } -} + unsigned long tmp; -/* s3c2410_pm_do_restore - * - * restore the system from the given list of saved registers - * - * Note, we do not use DBG() in here, as the system may not have - * restore the UARTs state yet -*/ + /* unset the return-from-sleep flag, to ensure reset */ -void s3c2410_pm_do_restore(struct sleep_save *ptr, int count) -{ - for (; count > 0; count--, ptr++) { - printk(KERN_DEBUG "restore %p (restore %08lx, was %08x)\n", - ptr->reg, ptr->val, __raw_readl(ptr->reg)); - - __raw_writel(ptr->val, ptr->reg); - } -} + tmp = __raw_readl(S3C2410_GSTATUS2); + tmp &= S3C2410_GSTATUS2_OFFRESET; + __raw_writel(tmp, S3C2410_GSTATUS2); -/* s3c2410_pm_do_restore_core - * - * similar to s3c2410_pm_do_restore_core - * - * WARNING: Do not put any debug in here that may effect memory or use - * peripherals, as things may be changing! -*/ + if ( machine_is_aml_m5900() ) + s3c2410_gpio_setpin(S3C2410_GPF2, 0); -static void s3c2410_pm_do_restore_core(struct sleep_save *ptr, int count) -{ - for (; count > 0; count--, ptr++) { - __raw_writel(ptr->val, ptr->reg); - } + return 0; } -/* s3c2410_pm_show_resume_irqs - * - * print any IRQs asserted at resume time (ie, we woke from) -*/ - -static void s3c2410_pm_show_resume_irqs(int start, unsigned long which, - unsigned long mask) +static int s3c2410_pm_add(struct sys_device *dev) { - int i; + pm_cpu_prep = s3c2410_pm_prepare; + pm_cpu_sleep = s3c2410_cpu_suspend; - which &= ~mask; - - for (i = 0; i <= 31; i++) { - if ((which) & (1L< - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -/* s3c2410_pm_init - * - * called from board at initialisation time to setup the power - * management -*/ - -#ifdef CONFIG_PM - -extern __init int s3c2410_pm_init(void); - -#else - -static inline int s3c2410_pm_init(void) -{ - return 0; -} -#endif - -/* configuration for the IRQ mask over sleep */ -extern unsigned long s3c_irqwake_intmask; -extern unsigned long s3c_irqwake_eintmask; - -/* IRQ masks for IRQs allowed to go to sleep (see irq.c) */ -extern unsigned long s3c_irqwake_intallow; -extern unsigned long s3c_irqwake_eintallow; - -/* per-cpu sleep functions */ - -extern void (*pm_cpu_prep)(void); -extern void (*pm_cpu_sleep)(void); - -/* Flags for PM Control */ - -extern unsigned long s3c_pm_flags; - -/* from sleep.S */ - -extern int s3c2410_cpu_save(unsigned long *saveblk); -extern void s3c2410_cpu_suspend(void); -extern void s3c2410_cpu_resume(void); - -extern unsigned long s3c2410_sleep_save_phys; - -/* sleep save info */ - -struct sleep_save { - void __iomem *reg; - unsigned long val; -}; - -#define SAVE_ITEM(x) \ - { .reg = (x) } - -extern void s3c2410_pm_do_save(struct sleep_save *ptr, int count); -extern void s3c2410_pm_do_restore(struct sleep_save *ptr, int count); - -#ifdef CONFIG_PM -extern int s3c24xx_irq_suspend(struct sys_device *dev, pm_message_t state); -extern int s3c24xx_irq_resume(struct sys_device *dev); -#else -#define s3c24xx_irq_suspend NULL -#define s3c24xx_irq_resume NULL -#endif diff --git a/arch/arm/mach-s3c2410/s3c2400-gpio.c b/arch/arm/mach-s3c2410/s3c2400-gpio.c deleted file mode 100644 index 1576d01d5f82..000000000000 --- a/arch/arm/mach-s3c2410/s3c2400-gpio.c +++ /dev/null @@ -1,42 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2400-gpio.c - * - * Copyright (c) 2006 Lucas Correia Villa Real - * - * S3C2400 GPIO support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - -int s3c2400_gpio_getirq(unsigned int pin) -{ - if (pin < S3C2410_GPE0 || pin > S3C2400_GPE7_EINT7) - return -1; /* not valid interrupts */ - - return (pin - S3C2410_GPE0) + IRQ_EINT0; -} - -EXPORT_SYMBOL(s3c2400_gpio_getirq); diff --git a/arch/arm/mach-s3c2410/s3c2400.h b/arch/arm/mach-s3c2410/s3c2400.h deleted file mode 100644 index 8b2394e1ed40..000000000000 --- a/arch/arm/mach-s3c2410/s3c2400.h +++ /dev/null @@ -1,31 +0,0 @@ -/* arch/arm/mach-s3c2410/s3c2400.h - * - * Copyright (c) 2004 Simtec Electronics - * Ben Dooks - * - * Header file for S3C2400 cpu support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * Modifications: - * 09-Fev-2006 LCVR First version, based on s3c2410.h -*/ - -#ifdef CONFIG_CPU_S3C2400 - -extern int s3c2400_init(void); - -extern void s3c2400_map_io(struct map_desc *mach_desc, int size); - -extern void s3c2400_init_uarts(struct s3c2410_uartcfg *cfg, int no); - -extern void s3c2400_init_clocks(int xtal); - -#else -#define s3c2400_init_clocks NULL -#define s3c2400_init_uarts NULL -#define s3c2400_map_io NULL -#define s3c2400_init NULL -#endif diff --git a/arch/arm/mach-s3c2410/s3c2410-clock.c b/arch/arm/mach-s3c2410/s3c2410-clock.c deleted file mode 100644 index 992cc6af230e..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410-clock.c +++ /dev/null @@ -1,276 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2410-clock.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * S3C2410,S3C2440,S3C2442 Clock control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include - -#include -#include - -#include -#include -#include - -#include "s3c2410.h" -#include "clock.h" -#include "cpu.h" - -int s3c2410_clkcon_enable(struct clk *clk, int enable) -{ - unsigned int clocks = clk->ctrlbit; - unsigned long clkcon; - - clkcon = __raw_readl(S3C2410_CLKCON); - - if (enable) - clkcon |= clocks; - else - clkcon &= ~clocks; - - /* ensure none of the special function bits set */ - clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER); - - __raw_writel(clkcon, S3C2410_CLKCON); - - return 0; -} - -static int s3c2410_upll_enable(struct clk *clk, int enable) -{ - unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); - unsigned long orig = clkslow; - - if (enable) - clkslow &= ~S3C2410_CLKSLOW_UCLK_OFF; - else - clkslow |= S3C2410_CLKSLOW_UCLK_OFF; - - __raw_writel(clkslow, S3C2410_CLKSLOW); - - /* if we started the UPLL, then allow to settle */ - - if (enable && (orig & S3C2410_CLKSLOW_UCLK_OFF)) - udelay(200); - - return 0; -} - -/* standard clock definitions */ - -static struct clk init_clocks_disable[] = { - { - .name = "nand", - .id = -1, - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_NAND, - }, { - .name = "sdi", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_SDI, - }, { - .name = "adc", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_ADC, - }, { - .name = "i2c", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_IIC, - }, { - .name = "iis", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_IIS, - }, { - .name = "spi", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_SPI, - } -}; - -static struct clk init_clocks[] = { - { - .name = "lcd", - .id = -1, - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_LCDC, - }, { - .name = "gpio", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_GPIO, - }, { - .name = "usb-host", - .id = -1, - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBH, - }, { - .name = "usb-device", - .id = -1, - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBD, - }, { - .name = "timers", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_PWMT, - }, { - .name = "uart", - .id = 0, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART0, - }, { - .name = "uart", - .id = 1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART1, - }, { - .name = "uart", - .id = 2, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART2, - }, { - .name = "rtc", - .id = -1, - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_RTC, - }, { - .name = "watchdog", - .id = -1, - .parent = &clk_p, - .ctrlbit = 0, - }, { - .name = "usb-bus-host", - .id = -1, - .parent = &clk_usb_bus, - }, { - .name = "usb-bus-gadget", - .id = -1, - .parent = &clk_usb_bus, - }, -}; - -/* s3c2410_baseclk_add() - * - * Add all the clocks used by the s3c2410 or compatible CPUs - * such as the S3C2440 and S3C2442. - * - * We cannot use a system device as we are needed before any - * of the init-calls that initialise the devices are actually - * done. -*/ - -int __init s3c2410_baseclk_add(void) -{ - unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); - unsigned long clkcon = __raw_readl(S3C2410_CLKCON); - struct clk *clkp; - struct clk *xtal; - int ret; - int ptr; - - clk_upll.enable = s3c2410_upll_enable; - - if (s3c24xx_register_clock(&clk_usb_bus) < 0) - printk(KERN_ERR "failed to register usb bus clock\n"); - - /* register clocks from clock array */ - - clkp = init_clocks; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { - /* ensure that we note the clock state */ - - clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - } - - /* We must be careful disabling the clocks we are not intending to - * be using at boot time, as subsytems such as the LCD which do - * their own DMA requests to the bus can cause the system to lockup - * if they where in the middle of requesting bus access. - * - * Disabling the LCD clock if the LCD is active is very dangerous, - * and therefore the bootloader should be careful to not enable - * the LCD clock if it is not needed. - */ - - /* install (and disable) the clocks we do not need immediately */ - - clkp = init_clocks_disable; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) { - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - - s3c2410_clkcon_enable(clkp, 0); - } - - /* show the clock-slow value */ - - xtal = clk_get(NULL, "xtal"); - - printk("CLOCK: Slow mode (%ld.%ld MHz), %s, MPLL %s, UPLL %s\n", - print_mhz(clk_get_rate(xtal) / - ( 2 * S3C2410_CLKSLOW_GET_SLOWVAL(clkslow))), - (clkslow & S3C2410_CLKSLOW_SLOW) ? "slow" : "fast", - (clkslow & S3C2410_CLKSLOW_MPLL_OFF) ? "off" : "on", - (clkslow & S3C2410_CLKSLOW_UCLK_OFF) ? "off" : "on"); - - return 0; -} diff --git a/arch/arm/mach-s3c2410/s3c2410-dma.c b/arch/arm/mach-s3c2410/s3c2410-dma.c deleted file mode 100644 index e67ba3911f11..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410-dma.c +++ /dev/null @@ -1,161 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2410-dma.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * S3C2410 DMA selection - * - * http://armlinux.simtec.co.uk/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include - -#include -#include -#include "dma.h" - -#include "cpu.h" - -#include -#include -#include -#include -#include -#include -#include -#include - -static struct s3c24xx_dma_map __initdata s3c2410_dma_mappings[] = { - [DMACH_XD0] = { - .name = "xdreq0", - .channels[0] = S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID, - }, - [DMACH_XD1] = { - .name = "xdreq1", - .channels[1] = S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID, - }, - [DMACH_SDI] = { - .name = "sdi", - .channels[0] = S3C2410_DCON_CH0_SDI | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_SDI | DMA_CH_VALID, - .channels[3] = S3C2410_DCON_CH3_SDI | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, - .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_SPI0] = { - .name = "spi0", - .channels[1] = S3C2410_DCON_CH1_SPI | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, - .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, - }, - [DMACH_SPI1] = { - .name = "spi1", - .channels[3] = S3C2410_DCON_CH3_SPI | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, - .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, - }, - [DMACH_UART0] = { - .name = "uart0", - .channels[0] = S3C2410_DCON_CH0_UART0 | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, - }, - [DMACH_UART1] = { - .name = "uart1", - .channels[1] = S3C2410_DCON_CH1_UART1 | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, - }, - [DMACH_UART2] = { - .name = "uart2", - .channels[3] = S3C2410_DCON_CH3_UART2 | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, - }, - [DMACH_TIMER] = { - .name = "timer", - .channels[0] = S3C2410_DCON_CH0_TIMER | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_TIMER | DMA_CH_VALID, - .channels[3] = S3C2410_DCON_CH3_TIMER | DMA_CH_VALID, - }, - [DMACH_I2S_IN] = { - .name = "i2s-sdi", - .channels[1] = S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID, - .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_I2S_OUT] = { - .name = "i2s-sdo", - .channels[2] = S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_USB_EP1] = { - .name = "usb-ep1", - .channels[0] = S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID, - }, - [DMACH_USB_EP2] = { - .name = "usb-ep2", - .channels[1] = S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID, - }, - [DMACH_USB_EP3] = { - .name = "usb-ep3", - .channels[2] = S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID, - }, - [DMACH_USB_EP4] = { - .name = "usb-ep4", - .channels[3] =S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID, - }, -}; - -static void s3c2410_dma_select(struct s3c2410_dma_chan *chan, - struct s3c24xx_dma_map *map) -{ - chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID; -} - -static struct s3c24xx_dma_selection __initdata s3c2410_dma_sel = { - .select = s3c2410_dma_select, - .dcon_mask = 7 << 24, - .map = s3c2410_dma_mappings, - .map_size = ARRAY_SIZE(s3c2410_dma_mappings), -}; - -static int s3c2410_dma_add(struct sys_device *sysdev) -{ - return s3c24xx_dma_init_map(&s3c2410_dma_sel); -} - -#if defined(CONFIG_CPU_S3C2410) -static struct sysdev_driver s3c2410_dma_driver = { - .add = s3c2410_dma_add, -}; - -static int __init s3c2410_dma_init(void) -{ - return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_dma_driver); -} - -arch_initcall(s3c2410_dma_init); -#endif - -#if defined(CONFIG_CPU_S3C2442) -/* S3C2442 DMA contains the same selection table as the S3C2410 */ -static struct sysdev_driver s3c2442_dma_driver = { - .add = s3c2410_dma_add, -}; - -static int __init s3c2442_dma_init(void) -{ - return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_dma_driver); -} - -arch_initcall(s3c2442_dma_init); -#endif - diff --git a/arch/arm/mach-s3c2410/s3c2410-gpio.c b/arch/arm/mach-s3c2410/s3c2410-gpio.c deleted file mode 100644 index ec3a276cc3cf..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410-gpio.c +++ /dev/null @@ -1,71 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2410-gpio.c - * - * Copyright (c) 2004-2006 Simtec Electronics - * Ben Dooks - * - * S3C2410 GPIO support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - -int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, - unsigned int config) -{ - void __iomem *reg = S3C24XX_EINFLT0; - unsigned long flags; - unsigned long val; - - if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15) - return -1; - - config &= 0xff; - - pin -= S3C2410_GPG8; - reg += pin & ~3; - - local_irq_save(flags); - - /* update filter width and clock source */ - - val = __raw_readl(reg); - val &= ~(0xff << ((pin & 3) * 8)); - val |= config << ((pin & 3) * 8); - __raw_writel(val, reg); - - /* update filter enable */ - - val = __raw_readl(S3C24XX_EXTINT2); - val &= ~(1 << ((pin * 4) + 3)); - val |= on << ((pin * 4) + 3); - __raw_writel(val, S3C24XX_EXTINT2); - - local_irq_restore(flags); - - return 0; -} - -EXPORT_SYMBOL(s3c2410_gpio_irqfilter); diff --git a/arch/arm/mach-s3c2410/s3c2410-irq.c b/arch/arm/mach-s3c2410/s3c2410-irq.c deleted file mode 100644 index c796c9c76e78..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410-irq.c +++ /dev/null @@ -1,48 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2410-irq.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * -*/ - -#include -#include -#include -#include -#include -#include - -#include "cpu.h" -#include "pm.h" - -static int s3c2410_irq_add(struct sys_device *sysdev) -{ - return 0; -} - -static struct sysdev_driver s3c2410_irq_driver = { - .add = s3c2410_irq_add, - .suspend = s3c24xx_irq_suspend, - .resume = s3c24xx_irq_resume, -}; - -static int s3c2410_irq_init(void) -{ - return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_irq_driver); -} - -arch_initcall(s3c2410_irq_init); diff --git a/arch/arm/mach-s3c2410/s3c2410-pm.c b/arch/arm/mach-s3c2410/s3c2410-pm.c deleted file mode 100644 index 8bb6e5e21f59..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410-pm.c +++ /dev/null @@ -1,156 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2410-pm.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * S3C2410 (and compatible) Power Manager (Suspend-To-RAM) support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include -#include - -#include -#include - -#include - -#include -#include - -#include "cpu.h" -#include "pm.h" - -#ifdef CONFIG_S3C2410_PM_DEBUG -extern void pm_dbg(const char *fmt, ...); -#define DBG(fmt...) pm_dbg(fmt) -#else -#define DBG(fmt...) printk(KERN_DEBUG fmt) -#endif - -static void s3c2410_pm_prepare(void) -{ - /* ensure at least GSTATUS3 has the resume address */ - - __raw_writel(virt_to_phys(s3c2410_cpu_resume), S3C2410_GSTATUS3); - - DBG("GSTATUS3 0x%08x\n", __raw_readl(S3C2410_GSTATUS3)); - DBG("GSTATUS4 0x%08x\n", __raw_readl(S3C2410_GSTATUS4)); - - if (machine_is_h1940()) { - void *base = phys_to_virt(H1940_SUSPEND_CHECK); - unsigned long ptr; - unsigned long calc = 0; - - /* generate check for the bootloader to check on resume */ - - for (ptr = 0; ptr < 0x40000; ptr += 0x400) - calc += __raw_readl(base+ptr); - - __raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM)); - } - - /* the RX3715 uses similar code and the same H1940 and the - * same offsets for resume and checksum pointers */ - - if (machine_is_rx3715()) { - void *base = phys_to_virt(H1940_SUSPEND_CHECK); - unsigned long ptr; - unsigned long calc = 0; - - /* generate check for the bootloader to check on resume */ - - for (ptr = 0; ptr < 0x40000; ptr += 0x4) - calc += __raw_readl(base+ptr); - - __raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM)); - } - - if ( machine_is_aml_m5900() ) - s3c2410_gpio_setpin(S3C2410_GPF2, 1); - -} - -static int s3c2410_pm_resume(struct sys_device *dev) -{ - unsigned long tmp; - - /* unset the return-from-sleep flag, to ensure reset */ - - tmp = __raw_readl(S3C2410_GSTATUS2); - tmp &= S3C2410_GSTATUS2_OFFRESET; - __raw_writel(tmp, S3C2410_GSTATUS2); - - if ( machine_is_aml_m5900() ) - s3c2410_gpio_setpin(S3C2410_GPF2, 0); - - return 0; -} - -static int s3c2410_pm_add(struct sys_device *dev) -{ - pm_cpu_prep = s3c2410_pm_prepare; - pm_cpu_sleep = s3c2410_cpu_suspend; - - return 0; -} - -#if defined(CONFIG_CPU_S3C2410) -static struct sysdev_driver s3c2410_pm_driver = { - .add = s3c2410_pm_add, - .resume = s3c2410_pm_resume, -}; - -/* register ourselves */ - -static int __init s3c2410_pm_drvinit(void) -{ - return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_pm_driver); -} - -arch_initcall(s3c2410_pm_drvinit); -#endif - -#if defined(CONFIG_CPU_S3C2440) -static struct sysdev_driver s3c2440_pm_driver = { - .add = s3c2410_pm_add, - .resume = s3c2410_pm_resume, -}; - -static int __init s3c2440_pm_drvinit(void) -{ - return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_pm_driver); -} - -arch_initcall(s3c2440_pm_drvinit); -#endif - -#if defined(CONFIG_CPU_S3C2442) -static struct sysdev_driver s3c2442_pm_driver = { - .add = s3c2410_pm_add, - .resume = s3c2410_pm_resume, -}; - -static int __init s3c2442_pm_drvinit(void) -{ - return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_pm_driver); -} - -arch_initcall(s3c2442_pm_drvinit); -#endif diff --git a/arch/arm/mach-s3c2410/s3c2410-sleep.S b/arch/arm/mach-s3c2410/s3c2410-sleep.S deleted file mode 100644 index 9179a1024588..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410-sleep.S +++ /dev/null @@ -1,68 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2410-sleep.S - * - * Copyright (c) 2004 Simtec Electronics - * Ben Dooks - * - * S3C2410 Power Manager (Suspend-To-RAM) support - * - * Based on PXA/SA1100 sleep code by: - * Nicolas Pitre, (c) 2002 Monta Vista Software Inc - * Cliff Brake, (c) 2001 - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include - -#include -#include -#include -#include - - /* s3c2410_cpu_suspend - * - * put the cpu into sleep mode - */ - -ENTRY(s3c2410_cpu_suspend) - @@ prepare cpu to sleep - - ldr r4, =S3C2410_REFRESH - ldr r5, =S3C24XX_MISCCR - ldr r6, =S3C2410_CLKCON - ldr r7, [ r4 ] @ get REFRESH (and ensure in TLB) - ldr r8, [ r5 ] @ get MISCCR (and ensure in TLB) - ldr r9, [ r6 ] @ get CLKCON (and ensure in TLB) - - orr r7, r7, #S3C2410_REFRESH_SELF @ SDRAM sleep command - orr r8, r8, #S3C2410_MISCCR_SDSLEEP @ SDRAM power-down signals - orr r9, r9, #S3C2410_CLKCON_POWER @ power down command - - teq pc, #0 @ first as a trial-run to load cache - bl s3c2410_do_sleep - teq r0, r0 @ now do it for real - b s3c2410_do_sleep @ - - @@ align next bit of code to cache line - .align 8 -s3c2410_do_sleep: - streq r7, [ r4 ] @ SDRAM sleep command - streq r8, [ r5 ] @ SDRAM power-down config - streq r9, [ r6 ] @ CPU sleep -1: beq 1b - mov pc, r14 diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c index 4cdc0d70c19f..d96fdcf2d2e3 100644 --- a/arch/arm/mach-s3c2410/s3c2410.c +++ b/arch/arm/mach-s3c2410/s3c2410.c @@ -31,10 +31,10 @@ #include #include -#include "s3c2410.h" -#include "cpu.h" -#include "devs.h" -#include "clock.h" +#include +#include +#include +#include /* Initial IO mappings */ diff --git a/arch/arm/mach-s3c2410/s3c2410.h b/arch/arm/mach-s3c2410/s3c2410.h deleted file mode 100644 index fbed084f26d0..000000000000 --- a/arch/arm/mach-s3c2410/s3c2410.h +++ /dev/null @@ -1,31 +0,0 @@ -/* arch/arm/mach-s3c2410/s3c2410.h - * - * Copyright (c) 2004 Simtec Electronics - * Ben Dooks - * - * Header file for s3c2410 machine directory - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * -*/ - -#ifdef CONFIG_CPU_S3C2410 - -extern int s3c2410_init(void); - -extern void s3c2410_map_io(struct map_desc *mach_desc, int size); - -extern void s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no); - -extern void s3c2410_init_clocks(int xtal); - -extern int s3c2410_baseclk_add(void); - -#else -#define s3c2410_init_clocks NULL -#define s3c2410_init_uarts NULL -#define s3c2410_map_io NULL -#define s3c2410_init NULL -#endif diff --git a/arch/arm/mach-s3c2410/s3c2412-clock.c b/arch/arm/mach-s3c2410/s3c2412-clock.c deleted file mode 100644 index 8f94ad83901d..000000000000 --- a/arch/arm/mach-s3c2410/s3c2412-clock.c +++ /dev/null @@ -1,716 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2412-clock.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * S3C2412,S3C2413 Clock control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include - -#include -#include - -#include -#include -#include - -#include "s3c2412.h" -#include "clock.h" -#include "cpu.h" - -/* We currently have to assume that the system is running - * from the XTPll input, and that all ***REFCLKs are being - * fed from it, as we cannot read the state of OM[4] from - * software. - * - * It would be possible for each board initialisation to - * set the correct muxing at initialisation -*/ - -static int s3c2412_clkcon_enable(struct clk *clk, int enable) -{ - unsigned int clocks = clk->ctrlbit; - unsigned long clkcon; - - clkcon = __raw_readl(S3C2410_CLKCON); - - if (enable) - clkcon |= clocks; - else - clkcon &= ~clocks; - - __raw_writel(clkcon, S3C2410_CLKCON); - - return 0; -} - -static int s3c2412_upll_enable(struct clk *clk, int enable) -{ - unsigned long upllcon = __raw_readl(S3C2410_UPLLCON); - unsigned long orig = upllcon; - - if (!enable) - upllcon |= S3C2412_PLLCON_OFF; - else - upllcon &= ~S3C2412_PLLCON_OFF; - - __raw_writel(upllcon, S3C2410_UPLLCON); - - /* allow ~150uS for the PLL to settle and lock */ - - if (enable && (orig & S3C2412_PLLCON_OFF)) - udelay(150); - - return 0; -} - -/* clock selections */ - -/* CPU EXTCLK input */ -static struct clk clk_ext = { - .name = "extclk", - .id = -1, -}; - -static struct clk clk_erefclk = { - .name = "erefclk", - .id = -1, -}; - -static struct clk clk_urefclk = { - .name = "urefclk", - .id = -1, -}; - -static int s3c2412_setparent_usysclk(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_urefclk) - clksrc &= ~S3C2412_CLKSRC_USYSCLK_UPLL; - else if (parent == &clk_upll) - clksrc |= S3C2412_CLKSRC_USYSCLK_UPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static struct clk clk_usysclk = { - .name = "usysclk", - .id = -1, - .parent = &clk_xtal, - .set_parent = s3c2412_setparent_usysclk, -}; - -static struct clk clk_mrefclk = { - .name = "mrefclk", - .parent = &clk_xtal, - .id = -1, -}; - -static struct clk clk_mdivclk = { - .name = "mdivclk", - .parent = &clk_xtal, - .id = -1, -}; - -static int s3c2412_setparent_usbsrc(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_usysclk) - clksrc &= ~S3C2412_CLKSRC_USBCLK_HCLK; - else if (parent == &clk_h) - clksrc |= S3C2412_CLKSRC_USBCLK_HCLK; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static unsigned long s3c2412_roundrate_usbsrc(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - div = parent_rate / rate; - if (div > 2) - div = 2; - - return parent_rate / div; -} - -static unsigned long s3c2412_getrate_usbsrc(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - return parent_rate / ((div & S3C2412_CLKDIVN_USB48DIV) ? 2 : 1); -} - -static int s3c2412_setrate_usbsrc(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_usbsrc(clk, rate); - - if ((parent_rate / rate) == 2) - clkdivn |= S3C2412_CLKDIVN_USB48DIV; - else - clkdivn &= ~S3C2412_CLKDIVN_USB48DIV; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_usbsrc = { - .name = "usbsrc", - .id = -1, - .get_rate = s3c2412_getrate_usbsrc, - .set_rate = s3c2412_setrate_usbsrc, - .round_rate = s3c2412_roundrate_usbsrc, - .set_parent = s3c2412_setparent_usbsrc, -}; - -static int s3c2412_setparent_msysclk(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_mdivclk) - clksrc &= ~S3C2412_CLKSRC_MSYSCLK_MPLL; - else if (parent == &clk_upll) - clksrc |= S3C2412_CLKSRC_MSYSCLK_MPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static struct clk clk_msysclk = { - .name = "msysclk", - .id = -1, - .set_parent = s3c2412_setparent_msysclk, -}; - -/* these next clocks have an divider immediately after them, - * so we can register them with their divider and leave out the - * intermediate clock stage -*/ -static unsigned long s3c2412_roundrate_clksrc(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - /* note, we remove the +/- 1 calculations as they cancel out */ - - div = (rate / parent_rate); - - if (div < 1) - div = 1; - else if (div > 16) - div = 16; - - return parent_rate / div; -} - -static int s3c2412_setparent_uart(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_erefclk) - clksrc &= ~S3C2412_CLKSRC_UARTCLK_MPLL; - else if (parent == &clk_mpll) - clksrc |= S3C2412_CLKSRC_UARTCLK_MPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static unsigned long s3c2412_getrate_uart(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - div &= S3C2412_CLKDIVN_UARTDIV_MASK; - div >>= S3C2412_CLKDIVN_UARTDIV_SHIFT; - - return parent_rate / (div + 1); -} - -static int s3c2412_setrate_uart(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_clksrc(clk, rate); - - clkdivn &= ~S3C2412_CLKDIVN_UARTDIV_MASK; - clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_UARTDIV_SHIFT; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_uart = { - .name = "uartclk", - .id = -1, - .get_rate = s3c2412_getrate_uart, - .set_rate = s3c2412_setrate_uart, - .set_parent = s3c2412_setparent_uart, - .round_rate = s3c2412_roundrate_clksrc, -}; - -static int s3c2412_setparent_i2s(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_erefclk) - clksrc &= ~S3C2412_CLKSRC_I2SCLK_MPLL; - else if (parent == &clk_mpll) - clksrc |= S3C2412_CLKSRC_I2SCLK_MPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static unsigned long s3c2412_getrate_i2s(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - div &= S3C2412_CLKDIVN_I2SDIV_MASK; - div >>= S3C2412_CLKDIVN_I2SDIV_SHIFT; - - return parent_rate / (div + 1); -} - -static int s3c2412_setrate_i2s(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_clksrc(clk, rate); - - clkdivn &= ~S3C2412_CLKDIVN_I2SDIV_MASK; - clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_I2SDIV_SHIFT; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_i2s = { - .name = "i2sclk", - .id = -1, - .get_rate = s3c2412_getrate_i2s, - .set_rate = s3c2412_setrate_i2s, - .set_parent = s3c2412_setparent_i2s, - .round_rate = s3c2412_roundrate_clksrc, -}; - -static int s3c2412_setparent_cam(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_usysclk) - clksrc &= ~S3C2412_CLKSRC_CAMCLK_HCLK; - else if (parent == &clk_h) - clksrc |= S3C2412_CLKSRC_CAMCLK_HCLK; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} -static unsigned long s3c2412_getrate_cam(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - div &= S3C2412_CLKDIVN_CAMDIV_MASK; - div >>= S3C2412_CLKDIVN_CAMDIV_SHIFT; - - return parent_rate / (div + 1); -} - -static int s3c2412_setrate_cam(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_clksrc(clk, rate); - - clkdivn &= ~S3C2412_CLKDIVN_CAMDIV_MASK; - clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_CAMDIV_SHIFT; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_cam = { - .name = "camif-upll", /* same as 2440 name */ - .id = -1, - .get_rate = s3c2412_getrate_cam, - .set_rate = s3c2412_setrate_cam, - .set_parent = s3c2412_setparent_cam, - .round_rate = s3c2412_roundrate_clksrc, -}; - -/* standard clock definitions */ - -static struct clk init_clocks_disable[] = { - { - .name = "nand", - .id = -1, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_NAND, - }, { - .name = "sdi", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_SDI, - }, { - .name = "adc", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_ADC, - }, { - .name = "i2c", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_IIC, - }, { - .name = "iis", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_IIS, - }, { - .name = "spi", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_SPI, - } -}; - -static struct clk init_clocks[] = { - { - .name = "dma", - .id = 0, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA0, - }, { - .name = "dma", - .id = 1, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA1, - }, { - .name = "dma", - .id = 2, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA2, - }, { - .name = "dma", - .id = 3, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA3, - }, { - .name = "lcd", - .id = -1, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_LCDC, - }, { - .name = "gpio", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_GPIO, - }, { - .name = "usb-host", - .id = -1, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USBH, - }, { - .name = "usb-device", - .id = -1, - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USBD, - }, { - .name = "timers", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_PWMT, - }, { - .name = "uart", - .id = 0, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_UART0, - }, { - .name = "uart", - .id = 1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_UART1, - }, { - .name = "uart", - .id = 2, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_UART2, - }, { - .name = "rtc", - .id = -1, - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_RTC, - }, { - .name = "watchdog", - .id = -1, - .parent = &clk_p, - .ctrlbit = 0, - }, { - .name = "usb-bus-gadget", - .id = -1, - .parent = &clk_usb_bus, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USB_DEV48, - }, { - .name = "usb-bus-host", - .id = -1, - .parent = &clk_usb_bus, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USB_HOST48, - } -}; - -/* clocks to add where we need to check their parentage */ - -struct clk_init { - struct clk *clk; - unsigned int bit; - struct clk *src_0; - struct clk *src_1; -}; - -static struct clk_init clks_src[] __initdata = { - { - .clk = &clk_usysclk, - .bit = S3C2412_CLKSRC_USBCLK_HCLK, - .src_0 = &clk_urefclk, - .src_1 = &clk_upll, - }, { - .clk = &clk_i2s, - .bit = S3C2412_CLKSRC_I2SCLK_MPLL, - .src_0 = &clk_erefclk, - .src_1 = &clk_mpll, - }, { - .clk = &clk_cam, - .bit = S3C2412_CLKSRC_CAMCLK_HCLK, - .src_0 = &clk_usysclk, - .src_1 = &clk_h, - }, { - .clk = &clk_msysclk, - .bit = S3C2412_CLKSRC_MSYSCLK_MPLL, - .src_0 = &clk_mdivclk, - .src_1 = &clk_mpll, - }, { - .clk = &clk_uart, - .bit = S3C2412_CLKSRC_UARTCLK_MPLL, - .src_0 = &clk_erefclk, - .src_1 = &clk_mpll, - }, { - .clk = &clk_usbsrc, - .bit = S3C2412_CLKSRC_USBCLK_HCLK, - .src_0 = &clk_usysclk, - .src_1 = &clk_h, - }, -}; - -/* s3c2412_clk_initparents - * - * Initialise the parents for the clocks that we get at start-time -*/ - -static void __init s3c2412_clk_initparents(void) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - struct clk_init *cip = clks_src; - struct clk *src; - int ptr; - int ret; - - for (ptr = 0; ptr < ARRAY_SIZE(clks_src); ptr++, cip++) { - ret = s3c24xx_register_clock(cip->clk); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - cip->clk->name, ret); - } - - src = (clksrc & cip->bit) ? cip->src_1 : cip->src_0; - - printk(KERN_INFO "%s: parent %s\n", cip->clk->name, src->name); - clk_set_parent(cip->clk, src); - } -} - -/* clocks to add straight away */ - -static struct clk *clks[] __initdata = { - &clk_ext, - &clk_usb_bus, - &clk_erefclk, - &clk_urefclk, - &clk_mrefclk, -}; - -int __init s3c2412_baseclk_add(void) -{ - unsigned long clkcon = __raw_readl(S3C2410_CLKCON); - struct clk *clkp; - int ret; - int ptr; - - clk_upll.enable = s3c2412_upll_enable; - clk_usb_bus.parent = &clk_usbsrc; - clk_usb_bus.rate = 0x0; - - s3c2412_clk_initparents(); - - for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) { - clkp = clks[ptr]; - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - } - - /* ensure usb bus clock is within correct rate of 48MHz */ - - if (clk_get_rate(&clk_usb_bus) != (48 * 1000 * 1000)) { - printk(KERN_INFO "Warning: USB bus clock not at 48MHz\n"); - - /* for the moment, let's use the UPLL, and see if we can - * get 48MHz */ - - clk_set_parent(&clk_usysclk, &clk_upll); - clk_set_parent(&clk_usbsrc, &clk_usysclk); - clk_set_rate(&clk_usbsrc, 48*1000*1000); - } - - printk("S3C2412: upll %s, %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n", - (__raw_readl(S3C2410_UPLLCON) & S3C2412_PLLCON_OFF) ? "off":"on", - print_mhz(clk_get_rate(&clk_upll)), - print_mhz(clk_get_rate(&clk_usb_bus))); - - /* register clocks from clock array */ - - clkp = init_clocks; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { - /* ensure that we note the clock state */ - - clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - } - - /* We must be careful disabling the clocks we are not intending to - * be using at boot time, as subsytems such as the LCD which do - * their own DMA requests to the bus can cause the system to lockup - * if they where in the middle of requesting bus access. - * - * Disabling the LCD clock if the LCD is active is very dangerous, - * and therefore the bootloader should be careful to not enable - * the LCD clock if it is not needed. - */ - - /* install (and disable) the clocks we do not need immediately */ - - clkp = init_clocks_disable; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) { - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - - s3c2412_clkcon_enable(clkp, 0); - } - - return 0; -} diff --git a/arch/arm/mach-s3c2410/s3c2412-dma.c b/arch/arm/mach-s3c2410/s3c2412-dma.c deleted file mode 100644 index 138f726ac6bf..000000000000 --- a/arch/arm/mach-s3c2410/s3c2412-dma.c +++ /dev/null @@ -1,161 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2412-dma.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * S3C2412 DMA selection - * - * http://armlinux.simtec.co.uk/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include - -#include -#include -#include - -#include "dma.h" -#include "cpu.h" - -#include -#include -#include -#include -#include -#include -#include -#include - -#define MAP(x) { (x)| DMA_CH_VALID, (x)| DMA_CH_VALID, (x)| DMA_CH_VALID, (x)| DMA_CH_VALID } - -static struct s3c24xx_dma_map __initdata s3c2412_dma_mappings[] = { - [DMACH_XD0] = { - .name = "xdreq0", - .channels = MAP(S3C2412_DMAREQSEL_XDREQ0), - }, - [DMACH_XD1] = { - .name = "xdreq1", - .channels = MAP(S3C2412_DMAREQSEL_XDREQ1), - }, - [DMACH_SDI] = { - .name = "sdi", - .channels = MAP(S3C2412_DMAREQSEL_SDI), - .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, - .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_SPI0] = { - .name = "spi0", - .channels = MAP(S3C2412_DMAREQSEL_SPI0TX), - .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, - .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, - }, - [DMACH_SPI1] = { - .name = "spi1", - .channels = MAP(S3C2412_DMAREQSEL_SPI1TX), - .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, - .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, - }, - [DMACH_UART0] = { - .name = "uart0", - .channels = MAP(S3C2412_DMAREQSEL_UART0_0), - .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, - }, - [DMACH_UART1] = { - .name = "uart1", - .channels = MAP(S3C2412_DMAREQSEL_UART1_0), - .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, - }, - [DMACH_UART2] = { - .name = "uart2", - .channels = MAP(S3C2412_DMAREQSEL_UART2_0), - .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, - }, - [DMACH_UART0_SRC2] = { - .name = "uart0", - .channels = MAP(S3C2412_DMAREQSEL_UART0_1), - .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, - }, - [DMACH_UART1_SRC2] = { - .name = "uart1", - .channels = MAP(S3C2412_DMAREQSEL_UART1_1), - .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, - }, - [DMACH_UART2_SRC2] = { - .name = "uart2", - .channels = MAP(S3C2412_DMAREQSEL_UART2_1), - .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, - }, - [DMACH_TIMER] = { - .name = "timer", - .channels = MAP(S3C2412_DMAREQSEL_TIMER), - }, - [DMACH_I2S_IN] = { - .name = "i2s-sdi", - .channels = MAP(S3C2412_DMAREQSEL_I2SRX), - .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_I2S_OUT] = { - .name = "i2s-sdo", - .channels = MAP(S3C2412_DMAREQSEL_I2STX), - .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_USB_EP1] = { - .name = "usb-ep1", - .channels = MAP(S3C2412_DMAREQSEL_USBEP1), - }, - [DMACH_USB_EP2] = { - .name = "usb-ep2", - .channels = MAP(S3C2412_DMAREQSEL_USBEP2), - }, - [DMACH_USB_EP3] = { - .name = "usb-ep3", - .channels = MAP(S3C2412_DMAREQSEL_USBEP3), - }, - [DMACH_USB_EP4] = { - .name = "usb-ep4", - .channels = MAP(S3C2412_DMAREQSEL_USBEP4), - }, -}; - -static void s3c2412_dma_select(struct s3c2410_dma_chan *chan, - struct s3c24xx_dma_map *map) -{ - writel(map->channels[0] | S3C2412_DMAREQSEL_HW, - chan->regs + S3C2412_DMA_DMAREQSEL); -} - -static struct s3c24xx_dma_selection __initdata s3c2412_dma_sel = { - .select = s3c2412_dma_select, - .dcon_mask = 0, - .map = s3c2412_dma_mappings, - .map_size = ARRAY_SIZE(s3c2412_dma_mappings), -}; - -static int s3c2412_dma_add(struct sys_device *sysdev) -{ - return s3c24xx_dma_init_map(&s3c2412_dma_sel); -} - -static struct sysdev_driver s3c2412_dma_driver = { - .add = s3c2412_dma_add, -}; - -static int __init s3c2412_dma_init(void) -{ - return sysdev_driver_register(&s3c2412_sysclass, &s3c2412_dma_driver); -} - -arch_initcall(s3c2412_dma_init); diff --git a/arch/arm/mach-s3c2410/s3c2412-irq.c b/arch/arm/mach-s3c2410/s3c2412-irq.c deleted file mode 100644 index ffcc30b23a80..000000000000 --- a/arch/arm/mach-s3c2410/s3c2412-irq.c +++ /dev/null @@ -1,133 +0,0 @@ -/* linux/arch/arm/mach-s3c2412/s3c2412-irq.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * -*/ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - -#include -#include - -#include "cpu.h" -#include "irq.h" -#include "pm.h" - -/* the s3c2412 changes the behaviour of IRQ_EINT0 through IRQ_EINT3 by - * having them turn up in both the INT* and the EINT* registers. Whilst - * both show the status, they both now need to be acked when the IRQs - * go off. -*/ - -static void -s3c2412_irq_mask(unsigned int irqno) -{ - unsigned long bitval = 1UL << (irqno - IRQ_EINT0); - unsigned long mask; - - mask = __raw_readl(S3C2410_INTMSK); - __raw_writel(mask | bitval, S3C2410_INTMSK); - - mask = __raw_readl(S3C2412_EINTMASK); - __raw_writel(mask | bitval, S3C2412_EINTMASK); -} - -static inline void -s3c2412_irq_ack(unsigned int irqno) -{ - unsigned long bitval = 1UL << (irqno - IRQ_EINT0); - - __raw_writel(bitval, S3C2412_EINTPEND); - __raw_writel(bitval, S3C2410_SRCPND); - __raw_writel(bitval, S3C2410_INTPND); -} - -static inline void -s3c2412_irq_maskack(unsigned int irqno) -{ - unsigned long bitval = 1UL << (irqno - IRQ_EINT0); - unsigned long mask; - - mask = __raw_readl(S3C2410_INTMSK); - __raw_writel(mask|bitval, S3C2410_INTMSK); - - mask = __raw_readl(S3C2412_EINTMASK); - __raw_writel(mask | bitval, S3C2412_EINTMASK); - - __raw_writel(bitval, S3C2412_EINTPEND); - __raw_writel(bitval, S3C2410_SRCPND); - __raw_writel(bitval, S3C2410_INTPND); -} - -static void -s3c2412_irq_unmask(unsigned int irqno) -{ - unsigned long bitval = 1UL << (irqno - IRQ_EINT0); - unsigned long mask; - - mask = __raw_readl(S3C2412_EINTMASK); - __raw_writel(mask & ~bitval, S3C2412_EINTMASK); - - mask = __raw_readl(S3C2410_INTMSK); - __raw_writel(mask & ~bitval, S3C2410_INTMSK); -} - -static struct irq_chip s3c2412_irq_eint0t4 = { - .ack = s3c2412_irq_ack, - .mask = s3c2412_irq_mask, - .unmask = s3c2412_irq_unmask, - .set_wake = s3c_irq_wake, - .set_type = s3c_irqext_type, -}; - -static int s3c2412_irq_add(struct sys_device *sysdev) -{ - unsigned int irqno; - - for (irqno = IRQ_EINT0; irqno <= IRQ_EINT3; irqno++) { - set_irq_chip(irqno, &s3c2412_irq_eint0t4); - set_irq_handler(irqno, handle_edge_irq); - set_irq_flags(irqno, IRQF_VALID); - } - - return 0; -} - -static struct sysdev_driver s3c2412_irq_driver = { - .add = s3c2412_irq_add, - .suspend = s3c24xx_irq_suspend, - .resume = s3c24xx_irq_resume, -}; - -static int s3c2412_irq_init(void) -{ - return sysdev_driver_register(&s3c2412_sysclass, &s3c2412_irq_driver); -} - -arch_initcall(s3c2412_irq_init); diff --git a/arch/arm/mach-s3c2410/s3c2412-pm.c b/arch/arm/mach-s3c2410/s3c2412-pm.c deleted file mode 100644 index 19b63322d259..000000000000 --- a/arch/arm/mach-s3c2410/s3c2412-pm.c +++ /dev/null @@ -1,128 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2412-pm.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * http://armlinux.simtec.co.uk/. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include - -#include "cpu.h" -#include "pm.h" - -#include "s3c2412.h" - -static void s3c2412_cpu_suspend(void) -{ - unsigned long tmp; - - /* set our standby method to sleep */ - - tmp = __raw_readl(S3C2412_PWRCFG); - tmp |= S3C2412_PWRCFG_STANDBYWFI_SLEEP; - __raw_writel(tmp, S3C2412_PWRCFG); - - /* issue the standby signal into the pm unit. Note, we - * issue a write-buffer drain just in case */ - - tmp = 0; - - asm("b 1f\n\t" - ".align 5\n\t" - "1:\n\t" - "mcr p15, 0, %0, c7, c10, 4\n\t" - "mcr p15, 0, %0, c7, c0, 4" :: "r" (tmp)); - - /* we should never get past here */ - - panic("sleep resumed to originator?"); -} - -static void s3c2412_pm_prepare(void) -{ -} - -static int s3c2412_pm_add(struct sys_device *sysdev) -{ - pm_cpu_prep = s3c2412_pm_prepare; - pm_cpu_sleep = s3c2412_cpu_suspend; - - return 0; -} - -static struct sleep_save s3c2412_sleep[] = { - SAVE_ITEM(S3C2412_DSC0), - SAVE_ITEM(S3C2412_DSC1), - SAVE_ITEM(S3C2413_GPJDAT), - SAVE_ITEM(S3C2413_GPJCON), - SAVE_ITEM(S3C2413_GPJUP), - - /* save the PWRCFG to get back to original sleep method */ - - SAVE_ITEM(S3C2412_PWRCFG), - - /* save the sleep configuration anyway, just in case these - * get damaged during wakeup */ - - SAVE_ITEM(S3C2412_GPBSLPCON), - SAVE_ITEM(S3C2412_GPCSLPCON), - SAVE_ITEM(S3C2412_GPDSLPCON), - SAVE_ITEM(S3C2412_GPESLPCON), - SAVE_ITEM(S3C2412_GPFSLPCON), - SAVE_ITEM(S3C2412_GPGSLPCON), - SAVE_ITEM(S3C2412_GPHSLPCON), - SAVE_ITEM(S3C2413_GPJSLPCON), -}; - -static int s3c2412_pm_suspend(struct sys_device *dev, pm_message_t state) -{ - s3c2410_pm_do_save(s3c2412_sleep, ARRAY_SIZE(s3c2412_sleep)); - return 0; -} - -static int s3c2412_pm_resume(struct sys_device *dev) -{ - unsigned long tmp; - - tmp = __raw_readl(S3C2412_PWRCFG); - tmp &= ~S3C2412_PWRCFG_STANDBYWFI_MASK; - tmp |= S3C2412_PWRCFG_STANDBYWFI_IDLE; - __raw_writel(tmp, S3C2412_PWRCFG); - - s3c2410_pm_do_restore(s3c2412_sleep, ARRAY_SIZE(s3c2412_sleep)); - return 0; -} - -static struct sysdev_driver s3c2412_pm_driver = { - .add = s3c2412_pm_add, - .suspend = s3c2412_pm_suspend, - .resume = s3c2412_pm_resume, -}; - -static __init int s3c2412_pm_init(void) -{ - return sysdev_driver_register(&s3c2412_sysclass, &s3c2412_pm_driver); -} - -arch_initcall(s3c2412_pm_init); diff --git a/arch/arm/mach-s3c2410/s3c2412.c b/arch/arm/mach-s3c2410/s3c2412.c deleted file mode 100644 index 2f651a811ecd..000000000000 --- a/arch/arm/mach-s3c2410/s3c2412.c +++ /dev/null @@ -1,181 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2412.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * http://armlinux.simtec.co.uk/. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include - -#include - -#include -#include -#include -#include -#include -#include - -#include "s3c2412.h" -#include "cpu.h" -#include "devs.h" -#include "clock.h" -#include "pm.h" - -#ifndef CONFIG_CPU_S3C2412_ONLY -void __iomem *s3c24xx_va_gpio2 = S3C24XX_VA_GPIO; - -static inline void s3c2412_init_gpio2(void) -{ - s3c24xx_va_gpio2 = S3C24XX_VA_GPIO + 0x10; -} -#else -#define s3c2412_init_gpio2() do { } while(0) -#endif - -/* Initial IO mappings */ - -static struct map_desc s3c2412_iodesc[] __initdata = { - IODESC_ENT(CLKPWR), - IODESC_ENT(LCD), - IODESC_ENT(TIMER), - IODESC_ENT(WATCHDOG), -}; - -/* uart registration process */ - -void __init s3c2412_init_uarts(struct s3c2410_uartcfg *cfg, int no) -{ - s3c24xx_init_uartdevs("s3c2412-uart", s3c2410_uart_resources, cfg, no); - - /* rename devices that are s3c2412/s3c2413 specific */ - s3c_device_sdi.name = "s3c2412-sdi"; - s3c_device_lcd.name = "s3c2412-lcd"; - s3c_device_nand.name = "s3c2412-nand"; -} - -/* s3c2412_idle - * - * use the standard idle call by ensuring the idle mode - * in power config, then issuing the idle co-processor - * instruction -*/ - -static void s3c2412_idle(void) -{ - unsigned long tmp; - - /* ensure our idle mode is to go to idle */ - - tmp = __raw_readl(S3C2412_PWRCFG); - tmp &= ~S3C2412_PWRCFG_STANDBYWFI_MASK; - tmp |= S3C2412_PWRCFG_STANDBYWFI_IDLE; - __raw_writel(tmp, S3C2412_PWRCFG); - - cpu_do_idle(); -} - -/* s3c2412_map_io - * - * register the standard cpu IO areas, and any passed in from the - * machine specific initialisation. -*/ - -void __init s3c2412_map_io(struct map_desc *mach_desc, int mach_size) -{ - /* move base of IO */ - - s3c2412_init_gpio2(); - - /* set our idle function */ - - s3c24xx_idle = s3c2412_idle; - - /* register our io-tables */ - - iotable_init(s3c2412_iodesc, ARRAY_SIZE(s3c2412_iodesc)); - iotable_init(mach_desc, mach_size); -} - -void __init s3c2412_init_clocks(int xtal) -{ - unsigned long tmp; - unsigned long fclk; - unsigned long hclk; - unsigned long pclk; - - /* now we've got our machine bits initialised, work out what - * clocks we've got */ - - fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal*2); - - tmp = __raw_readl(S3C2410_CLKDIVN); - - /* work out clock scalings */ - - hclk = fclk / ((tmp & S3C2412_CLKDIVN_HDIVN_MASK) + 1); - hclk /= ((tmp & S3C2421_CLKDIVN_ARMDIVN) ? 2 : 1); - pclk = hclk / ((tmp & S3C2412_CLKDIVN_PDIVN) ? 2 : 1); - - /* print brieft summary of clocks, etc */ - - printk("S3C2412: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", - print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); - - /* initialise the clocks here, to allow other things like the - * console to use them - */ - - s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); - s3c2412_baseclk_add(); -} - -/* need to register class before we actually register the device, and - * we also need to ensure that it has been initialised before any of the - * drivers even try to use it (even if not on an s3c2412 based system) - * as a driver which may support both 2410 and 2440 may try and use it. -*/ - -struct sysdev_class s3c2412_sysclass = { - set_kset_name("s3c2412-core"), -}; - -static int __init s3c2412_core_init(void) -{ - return sysdev_class_register(&s3c2412_sysclass); -} - -core_initcall(s3c2412_core_init); - -static struct sys_device s3c2412_sysdev = { - .cls = &s3c2412_sysclass, -}; - -int __init s3c2412_init(void) -{ - printk("S3C2412: Initialising architecture\n"); - - return sysdev_register(&s3c2412_sysdev); -} diff --git a/arch/arm/mach-s3c2410/s3c2412.h b/arch/arm/mach-s3c2410/s3c2412.h deleted file mode 100644 index c6e56032a6e7..000000000000 --- a/arch/arm/mach-s3c2410/s3c2412.h +++ /dev/null @@ -1,29 +0,0 @@ -/* arch/arm/mach-s3c2410/s3c2412.h - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * Header file for s3c2412 cpu support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#ifdef CONFIG_CPU_S3C2412 - -extern int s3c2412_init(void); - -extern void s3c2412_map_io(struct map_desc *mach_desc, int size); - -extern void s3c2412_init_uarts(struct s3c2410_uartcfg *cfg, int no); - -extern void s3c2412_init_clocks(int xtal); - -extern int s3c2412_baseclk_add(void); -#else -#define s3c2412_init_clocks NULL -#define s3c2412_init_uarts NULL -#define s3c2412_map_io NULL -#define s3c2412_init NULL -#endif diff --git a/arch/arm/mach-s3c2410/s3c2440-clock.c b/arch/arm/mach-s3c2410/s3c2440-clock.c deleted file mode 100644 index ba13c1d079d1..000000000000 --- a/arch/arm/mach-s3c2410/s3c2440-clock.c +++ /dev/null @@ -1,170 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2440-clock.c - * - * Copyright (c) 2004-2005 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * Ben Dooks - * - * S3C2440 Clock support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include - -#include "clock.h" -#include "cpu.h" - -/* S3C2440 extended clock support */ - -static unsigned long s3c2440_camif_upll_round(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - /* note, we remove the +/- 1 calculations for the divisor */ - - div = (parent_rate / rate) / 2; - - if (div < 1) - div = 1; - else if (div > 16) - div = 16; - - return parent_rate / (div * 2); -} - -static int s3c2440_camif_upll_setrate(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - - rate = s3c2440_camif_upll_round(clk, rate); - - camdivn &= ~(S3C2440_CAMDIVN_CAMCLK_SEL | S3C2440_CAMDIVN_CAMCLK_MASK); - - if (rate != parent_rate) { - camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; - camdivn |= (((parent_rate / rate) / 2) - 1); - } - - __raw_writel(camdivn, S3C2440_CAMDIVN); - - return 0; -} - -/* Extra S3C2440 clocks */ - -static struct clk s3c2440_clk_cam = { - .name = "camif", - .id = -1, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2440_CLKCON_CAMERA, -}; - -static struct clk s3c2440_clk_cam_upll = { - .name = "camif-upll", - .id = -1, - .set_rate = s3c2440_camif_upll_setrate, - .round_rate = s3c2440_camif_upll_round, -}; - -static struct clk s3c2440_clk_ac97 = { - .name = "ac97", - .id = -1, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2440_CLKCON_CAMERA, -}; - -static int s3c2440_clk_add(struct sys_device *sysdev) -{ - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - unsigned long clkdivn; - struct clk *clock_h; - struct clk *clock_p; - struct clk *clock_upll; - - printk("S3C2440: Clock Support, DVS %s\n", - (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off"); - - clock_p = clk_get(NULL, "pclk"); - clock_h = clk_get(NULL, "hclk"); - clock_upll = clk_get(NULL, "upll"); - - if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) { - printk(KERN_ERR "S3C2440: Failed to get parent clocks\n"); - return -EINVAL; - } - - /* check rate of UPLL, and if it is near 96MHz, then change - * to using half the UPLL rate for the system */ - - if (clk_get_rate(clock_upll) > (94 * MHZ)) { - clk_usb_bus.rate = clk_get_rate(clock_upll) / 2; - - mutex_lock(&clocks_mutex); - - clkdivn = __raw_readl(S3C2410_CLKDIVN); - clkdivn |= S3C2440_CLKDIVN_UCLK; - __raw_writel(clkdivn, S3C2410_CLKDIVN); - - mutex_unlock(&clocks_mutex); - } - - s3c2440_clk_cam.parent = clock_h; - s3c2440_clk_ac97.parent = clock_p; - s3c2440_clk_cam_upll.parent = clock_upll; - - s3c24xx_register_clock(&s3c2440_clk_ac97); - s3c24xx_register_clock(&s3c2440_clk_cam); - s3c24xx_register_clock(&s3c2440_clk_cam_upll); - - clk_disable(&s3c2440_clk_ac97); - clk_disable(&s3c2440_clk_cam); - - return 0; -} - -static struct sysdev_driver s3c2440_clk_driver = { - .add = s3c2440_clk_add, -}; - -static __init int s3c24xx_clk_driver(void) -{ - return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_clk_driver); -} - -arch_initcall(s3c24xx_clk_driver); diff --git a/arch/arm/mach-s3c2410/s3c2440-dma.c b/arch/arm/mach-s3c2410/s3c2440-dma.c deleted file mode 100644 index 47b861b9443d..000000000000 --- a/arch/arm/mach-s3c2410/s3c2440-dma.c +++ /dev/null @@ -1,165 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2440-dma.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * S3C2440 DMA selection - * - * http://armlinux.simtec.co.uk/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include - -#include -#include -#include "dma.h" - -#include "cpu.h" - -#include -#include -#include -#include -#include -#include -#include -#include - -static struct s3c24xx_dma_map __initdata s3c2440_dma_mappings[] = { - [DMACH_XD0] = { - .name = "xdreq0", - .channels[0] = S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID, - }, - [DMACH_XD1] = { - .name = "xdreq1", - .channels[1] = S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID, - }, - [DMACH_SDI] = { - .name = "sdi", - .channels[0] = S3C2410_DCON_CH0_SDI | DMA_CH_VALID, - .channels[1] = S3C2440_DCON_CH1_SDI | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_SDI | DMA_CH_VALID, - .channels[3] = S3C2410_DCON_CH3_SDI | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, - .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_SPI0] = { - .name = "spi0", - .channels[1] = S3C2410_DCON_CH1_SPI | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, - .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, - }, - [DMACH_SPI1] = { - .name = "spi1", - .channels[3] = S3C2410_DCON_CH3_SPI | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, - .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, - }, - [DMACH_UART0] = { - .name = "uart0", - .channels[0] = S3C2410_DCON_CH0_UART0 | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, - }, - [DMACH_UART1] = { - .name = "uart1", - .channels[1] = S3C2410_DCON_CH1_UART1 | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, - }, - [DMACH_UART2] = { - .name = "uart2", - .channels[3] = S3C2410_DCON_CH3_UART2 | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, - .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, - }, - [DMACH_TIMER] = { - .name = "timer", - .channels[0] = S3C2410_DCON_CH0_TIMER | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_TIMER | DMA_CH_VALID, - .channels[3] = S3C2410_DCON_CH3_TIMER | DMA_CH_VALID, - }, - [DMACH_I2S_IN] = { - .name = "i2s-sdi", - .channels[1] = S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID, - .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_I2S_OUT] = { - .name = "i2s-sdo", - .channels[0] = S3C2440_DCON_CH0_I2SSDO | DMA_CH_VALID, - .channels[2] = S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID, - .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, - }, - [DMACH_PCM_IN] = { - .name = "pcm-in", - .channels[0] = S3C2440_DCON_CH0_PCMIN | DMA_CH_VALID, - .channels[2] = S3C2440_DCON_CH2_PCMIN | DMA_CH_VALID, - .hw_addr.from = S3C2440_PA_AC97 + S3C_AC97_PCM_DATA, - }, - [DMACH_PCM_OUT] = { - .name = "pcm-out", - .channels[1] = S3C2440_DCON_CH1_PCMOUT | DMA_CH_VALID, - .channels[3] = S3C2440_DCON_CH3_PCMOUT | DMA_CH_VALID, - .hw_addr.to = S3C2440_PA_AC97 + S3C_AC97_PCM_DATA, - }, - [DMACH_MIC_IN] = { - .name = "mic-in", - .channels[2] = S3C2440_DCON_CH2_MICIN | DMA_CH_VALID, - .channels[3] = S3C2440_DCON_CH3_MICIN | DMA_CH_VALID, - .hw_addr.from = S3C2440_PA_AC97 + S3C_AC97_MIC_DATA, - }, - [DMACH_USB_EP1] = { - .name = "usb-ep1", - .channels[0] = S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID, - }, - [DMACH_USB_EP2] = { - .name = "usb-ep2", - .channels[1] = S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID, - }, - [DMACH_USB_EP3] = { - .name = "usb-ep3", - .channels[2] = S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID, - }, - [DMACH_USB_EP4] = { - .name = "usb-ep4", - .channels[3] = S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID, - }, -}; - -static void s3c2440_dma_select(struct s3c2410_dma_chan *chan, - struct s3c24xx_dma_map *map) -{ - chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID; -} - -static struct s3c24xx_dma_selection __initdata s3c2440_dma_sel = { - .select = s3c2440_dma_select, - .dcon_mask = 7 << 24, - .map = s3c2440_dma_mappings, - .map_size = ARRAY_SIZE(s3c2440_dma_mappings), -}; - -static int s3c2440_dma_add(struct sys_device *sysdev) -{ - return s3c24xx_dma_init_map(&s3c2440_dma_sel); -} - -static struct sysdev_driver s3c2440_dma_driver = { - .add = s3c2440_dma_add, -}; - -static int __init s3c2440_dma_init(void) -{ - return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_dma_driver); -} - -arch_initcall(s3c2440_dma_init); - diff --git a/arch/arm/mach-s3c2410/s3c2440-dsc.c b/arch/arm/mach-s3c2410/s3c2440-dsc.c deleted file mode 100644 index c92ea66ba45e..000000000000 --- a/arch/arm/mach-s3c2410/s3c2440-dsc.c +++ /dev/null @@ -1,54 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2440-dsc.c - * - * Copyright (c) 2004-2005 Simtec Electronics - * Ben Dooks - * - * Samsung S3C2440 Drive Strength Control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "cpu.h" -#include "s3c2440.h" - -int s3c2440_set_dsc(unsigned int pin, unsigned int value) -{ - void __iomem *base; - unsigned long val; - unsigned long flags; - unsigned long mask; - - base = (pin & S3C2440_SELECT_DSC1) ? S3C2440_DSC1 : S3C2440_DSC0; - mask = 3 << S3C2440_DSC_GETSHIFT(pin); - - local_irq_save(flags); - - val = __raw_readl(base); - val &= ~mask; - val |= value & mask; - __raw_writel(val, base); - - local_irq_restore(flags); - return 0; -} - -EXPORT_SYMBOL(s3c2440_set_dsc); diff --git a/arch/arm/mach-s3c2410/s3c2440-irq.c b/arch/arm/mach-s3c2410/s3c2440-irq.c deleted file mode 100644 index 1ba19b27ab05..000000000000 --- a/arch/arm/mach-s3c2410/s3c2440-irq.c +++ /dev/null @@ -1,130 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2440-irq.c - * - * Copyright (c) 2003,2004 Simtec Electronics - * Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * -*/ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - -#include -#include - -#include "cpu.h" -#include "pm.h" -#include "irq.h" - -/* WDT/AC97 */ - -static void s3c_irq_demux_wdtac97(unsigned int irq, - struct irq_desc *desc) -{ - unsigned int subsrc, submsk; - struct irq_desc *mydesc; - - /* read the current pending interrupts, and the mask - * for what it is available */ - - subsrc = __raw_readl(S3C2410_SUBSRCPND); - submsk = __raw_readl(S3C2410_INTSUBMSK); - - subsrc &= ~submsk; - subsrc >>= 13; - subsrc &= 3; - - if (subsrc != 0) { - if (subsrc & 1) { - mydesc = irq_desc + IRQ_S3C2440_WDT; - desc_handle_irq(IRQ_S3C2440_WDT, mydesc); - } - if (subsrc & 2) { - mydesc = irq_desc + IRQ_S3C2440_AC97; - desc_handle_irq(IRQ_S3C2440_AC97, mydesc); - } - } -} - - -#define INTMSK_WDT (1UL << (IRQ_WDT - IRQ_EINT0)) - -static void -s3c_irq_wdtac97_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_WDT, 3<<13); -} - -static void -s3c_irq_wdtac97_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_WDT); -} - -static void -s3c_irq_wdtac97_ack(unsigned int irqno) -{ - s3c_irqsub_maskack(irqno, INTMSK_WDT, 3<<13); -} - -static struct irq_chip s3c_irq_wdtac97 = { - .mask = s3c_irq_wdtac97_mask, - .unmask = s3c_irq_wdtac97_unmask, - .ack = s3c_irq_wdtac97_ack, -}; - -static int s3c2440_irq_add(struct sys_device *sysdev) -{ - unsigned int irqno; - - printk("S3C2440: IRQ Support\n"); - - /* add new chained handler for wdt, ac7 */ - - set_irq_chip(IRQ_WDT, &s3c_irq_level_chip); - set_irq_handler(IRQ_WDT, handle_level_irq); - set_irq_chained_handler(IRQ_WDT, s3c_irq_demux_wdtac97); - - for (irqno = IRQ_S3C2440_WDT; irqno <= IRQ_S3C2440_AC97; irqno++) { - set_irq_chip(irqno, &s3c_irq_wdtac97); - set_irq_handler(irqno, handle_level_irq); - set_irq_flags(irqno, IRQF_VALID); - } - - return 0; -} - -static struct sysdev_driver s3c2440_irq_driver = { - .add = s3c2440_irq_add, -}; - -static int s3c2440_irq_init(void) -{ - return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver); -} - -arch_initcall(s3c2440_irq_init); - diff --git a/arch/arm/mach-s3c2410/s3c2440.c b/arch/arm/mach-s3c2410/s3c2440.c deleted file mode 100644 index 344eb27cca48..000000000000 --- a/arch/arm/mach-s3c2410/s3c2440.c +++ /dev/null @@ -1,52 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2440.c - * - * Copyright (c) 2004-2006 Simtec Electronics - * Ben Dooks - * - * Samsung S3C2440 Mobile CPU support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "s3c2440.h" -#include "devs.h" -#include "cpu.h" - -static struct sys_device s3c2440_sysdev = { - .cls = &s3c2440_sysclass, -}; - -int __init s3c2440_init(void) -{ - printk("S3C2440: Initialising architecture\n"); - - /* change irq for watchdog */ - - s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT; - s3c_device_wdt.resource[1].end = IRQ_S3C2440_WDT; - - /* register our system device for everything else */ - - return sysdev_register(&s3c2440_sysdev); -} diff --git a/arch/arm/mach-s3c2410/s3c2440.h b/arch/arm/mach-s3c2410/s3c2440.h deleted file mode 100644 index dcd316076c59..000000000000 --- a/arch/arm/mach-s3c2410/s3c2440.h +++ /dev/null @@ -1,17 +0,0 @@ -/* arch/arm/mach-s3c2410/s3c2440.h - * - * Copyright (c) 2004-2005 Simtec Electronics - * Ben Dooks - * - * Header file for s3c2440 cpu support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#ifdef CONFIG_CPU_S3C2440 -extern int s3c2440_init(void); -#else -#define s3c2440_init NULL -#endif diff --git a/arch/arm/mach-s3c2410/s3c2442-clock.c b/arch/arm/mach-s3c2410/s3c2442-clock.c deleted file mode 100644 index 4e292ca7c9be..000000000000 --- a/arch/arm/mach-s3c2410/s3c2442-clock.c +++ /dev/null @@ -1,171 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2442-clock.c - * - * Copyright (c) 2004-2005 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * Ben Dooks - * - * S3C2442 Clock support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include - -#include "clock.h" -#include "cpu.h" - -/* S3C2442 extended clock support */ - -static unsigned long s3c2442_camif_upll_round(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - div = parent_rate / rate; - - if (div == 3) - return parent_rate / 3; - - /* note, we remove the +/- 1 calculations for the divisor */ - - div /= 2; - - if (div < 1) - div = 1; - else if (div > 16) - div = 16; - - return parent_rate / (div * 2); -} - -static int s3c2442_camif_upll_setrate(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - - rate = s3c2442_camif_upll_round(clk, rate); - - camdivn &= ~S3C2442_CAMDIVN_CAMCLK_DIV3; - - if (rate == parent_rate) { - camdivn &= ~S3C2440_CAMDIVN_CAMCLK_SEL; - } else if ((parent_rate / rate) == 3) { - camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; - camdivn |= S3C2442_CAMDIVN_CAMCLK_DIV3; - } else { - camdivn &= ~S3C2440_CAMDIVN_CAMCLK_MASK; - camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; - camdivn |= (((parent_rate / rate) / 2) - 1); - } - - __raw_writel(camdivn, S3C2440_CAMDIVN); - - return 0; -} - -/* Extra S3C2442 clocks */ - -static struct clk s3c2442_clk_cam = { - .name = "camif", - .id = -1, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2440_CLKCON_CAMERA, -}; - -static struct clk s3c2442_clk_cam_upll = { - .name = "camif-upll", - .id = -1, - .set_rate = s3c2442_camif_upll_setrate, - .round_rate = s3c2442_camif_upll_round, -}; - -static int s3c2442_clk_add(struct sys_device *sysdev) -{ - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - unsigned long clkdivn; - struct clk *clock_h; - struct clk *clock_p; - struct clk *clock_upll; - - printk("S3C2442: Clock Support, DVS %s\n", - (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off"); - - clock_p = clk_get(NULL, "pclk"); - clock_h = clk_get(NULL, "hclk"); - clock_upll = clk_get(NULL, "upll"); - - if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) { - printk(KERN_ERR "S3C2442: Failed to get parent clocks\n"); - return -EINVAL; - } - - /* check rate of UPLL, and if it is near 96MHz, then change - * to using half the UPLL rate for the system */ - - if (clk_get_rate(clock_upll) > (94 * MHZ)) { - clk_usb_bus.rate = clk_get_rate(clock_upll) / 2; - - mutex_lock(&clocks_mutex); - - clkdivn = __raw_readl(S3C2410_CLKDIVN); - clkdivn |= S3C2440_CLKDIVN_UCLK; - __raw_writel(clkdivn, S3C2410_CLKDIVN); - - mutex_unlock(&clocks_mutex); - } - - s3c2442_clk_cam.parent = clock_h; - s3c2442_clk_cam_upll.parent = clock_upll; - - s3c24xx_register_clock(&s3c2442_clk_cam); - s3c24xx_register_clock(&s3c2442_clk_cam_upll); - - clk_disable(&s3c2442_clk_cam); - - return 0; -} - -static struct sysdev_driver s3c2442_clk_driver = { - .add = s3c2442_clk_add, -}; - -static __init int s3c2442_clk_init(void) -{ - return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_clk_driver); -} - -arch_initcall(s3c2442_clk_init); diff --git a/arch/arm/mach-s3c2410/s3c2442.c b/arch/arm/mach-s3c2410/s3c2442.c deleted file mode 100644 index 428732ee68c4..000000000000 --- a/arch/arm/mach-s3c2410/s3c2442.c +++ /dev/null @@ -1,34 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c2442.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * Samsung S3C2442 Mobile CPU support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include "s3c2442.h" -#include "cpu.h" - -static struct sys_device s3c2442_sysdev = { - .cls = &s3c2442_sysclass, -}; - -int __init s3c2442_init(void) -{ - printk("S3C2442: Initialising architecture\n"); - - return sysdev_register(&s3c2442_sysdev); -} diff --git a/arch/arm/mach-s3c2410/s3c2442.h b/arch/arm/mach-s3c2410/s3c2442.h deleted file mode 100644 index 0ae37d24866c..000000000000 --- a/arch/arm/mach-s3c2410/s3c2442.h +++ /dev/null @@ -1,17 +0,0 @@ -/* arch/arm/mach-s3c2410/s3c2442.h - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks - * - * Header file for s3c2442 cpu support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#ifdef CONFIG_CPU_S3C2442 -extern int s3c2442_init(void); -#else -#define s3c2442_init NULL -#endif diff --git a/arch/arm/mach-s3c2410/s3c244x-irq.c b/arch/arm/mach-s3c2410/s3c244x-irq.c deleted file mode 100644 index ede94636a72a..000000000000 --- a/arch/arm/mach-s3c2410/s3c244x-irq.c +++ /dev/null @@ -1,146 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c244x-irq.c - * - * Copyright (c) 2003,2004 Simtec Electronics - * Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * -*/ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include - -#include -#include - -#include "cpu.h" -#include "pm.h" -#include "irq.h" - -/* camera irq */ - -static void s3c_irq_demux_cam(unsigned int irq, - struct irq_desc *desc) -{ - unsigned int subsrc, submsk; - struct irq_desc *mydesc; - - /* read the current pending interrupts, and the mask - * for what it is available */ - - subsrc = __raw_readl(S3C2410_SUBSRCPND); - submsk = __raw_readl(S3C2410_INTSUBMSK); - - subsrc &= ~submsk; - subsrc >>= 11; - subsrc &= 3; - - if (subsrc != 0) { - if (subsrc & 1) { - mydesc = irq_desc + IRQ_S3C2440_CAM_C; - desc_handle_irq(IRQ_S3C2440_CAM_C, mydesc); - } - if (subsrc & 2) { - mydesc = irq_desc + IRQ_S3C2440_CAM_P; - desc_handle_irq(IRQ_S3C2440_CAM_P, mydesc); - } - } -} - -#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0)) - -static void -s3c_irq_cam_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_CAM, 3<<11); -} - -static void -s3c_irq_cam_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_CAM); -} - -static void -s3c_irq_cam_ack(unsigned int irqno) -{ - s3c_irqsub_maskack(irqno, INTMSK_CAM, 3<<11); -} - -static struct irq_chip s3c_irq_cam = { - .mask = s3c_irq_cam_mask, - .unmask = s3c_irq_cam_unmask, - .ack = s3c_irq_cam_ack, -}; - -static int s3c244x_irq_add(struct sys_device *sysdev) -{ - unsigned int irqno; - - set_irq_chip(IRQ_NFCON, &s3c_irq_level_chip); - set_irq_handler(IRQ_NFCON, handle_level_irq); - set_irq_flags(IRQ_NFCON, IRQF_VALID); - - /* add chained handler for camera */ - - set_irq_chip(IRQ_CAM, &s3c_irq_level_chip); - set_irq_handler(IRQ_CAM, handle_level_irq); - set_irq_chained_handler(IRQ_CAM, s3c_irq_demux_cam); - - for (irqno = IRQ_S3C2440_CAM_C; irqno <= IRQ_S3C2440_CAM_P; irqno++) { - set_irq_chip(irqno, &s3c_irq_cam); - set_irq_handler(irqno, handle_level_irq); - set_irq_flags(irqno, IRQF_VALID); - } - - return 0; -} - -static struct sysdev_driver s3c2440_irq_driver = { - .add = s3c244x_irq_add, - .suspend = s3c24xx_irq_suspend, - .resume = s3c24xx_irq_resume, -}; - -static int s3c2440_irq_init(void) -{ - return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver); -} - -arch_initcall(s3c2440_irq_init); - -static struct sysdev_driver s3c2442_irq_driver = { - .add = s3c244x_irq_add, - .suspend = s3c24xx_irq_suspend, - .resume = s3c24xx_irq_resume, -}; - - -static int s3c2442_irq_init(void) -{ - return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_irq_driver); -} - -arch_initcall(s3c2442_irq_init); diff --git a/arch/arm/mach-s3c2410/s3c244x.c b/arch/arm/mach-s3c2410/s3c244x.c deleted file mode 100644 index 23c7494ad10d..000000000000 --- a/arch/arm/mach-s3c2410/s3c244x.c +++ /dev/null @@ -1,184 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/s3c244x.c - * - * Copyright (c) 2004-2006 Simtec Electronics - * Ben Dooks - * - * Samsung S3C2440 and S3C2442 Mobile CPU support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include -#include - -#include "s3c2410.h" -#include "s3c2440.h" -#include "s3c244x.h" -#include "clock.h" -#include "devs.h" -#include "cpu.h" -#include "pm.h" - -static struct map_desc s3c244x_iodesc[] __initdata = { - IODESC_ENT(CLKPWR), - IODESC_ENT(TIMER), - IODESC_ENT(WATCHDOG), - IODESC_ENT(LCD), -}; - -/* uart initialisation */ - -void __init s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no) -{ - s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no); -} - -void __init s3c244x_map_io(struct map_desc *mach_desc, int size) -{ - /* register our io-tables */ - - iotable_init(s3c244x_iodesc, ARRAY_SIZE(s3c244x_iodesc)); - iotable_init(mach_desc, size); - - /* rename any peripherals used differing from the s3c2410 */ - - s3c_device_i2c.name = "s3c2440-i2c"; - s3c_device_nand.name = "s3c2440-nand"; - s3c_device_usbgadget.name = "s3c2440-usbgadget"; -} - -void __init s3c244x_init_clocks(int xtal) -{ - unsigned long clkdiv; - unsigned long camdiv; - unsigned long hclk, fclk, pclk; - int hdiv = 1; - - /* now we've got our machine bits initialised, work out what - * clocks we've got */ - - fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2; - - clkdiv = __raw_readl(S3C2410_CLKDIVN); - camdiv = __raw_readl(S3C2440_CAMDIVN); - - /* work out clock scalings */ - - switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) { - case S3C2440_CLKDIVN_HDIVN_1: - hdiv = 1; - break; - - case S3C2440_CLKDIVN_HDIVN_2: - hdiv = 2; - break; - - case S3C2440_CLKDIVN_HDIVN_4_8: - hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4; - break; - - case S3C2440_CLKDIVN_HDIVN_3_6: - hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3; - break; - } - - hclk = fclk / hdiv; - pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1); - - /* print brief summary of clocks, etc */ - - printk("S3C244X: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", - print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); - - /* initialise the clocks here, to allow other things like the - * console to use them, and to add new ones after the initialisation - */ - - s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); - s3c2410_baseclk_add(); -} - -#ifdef CONFIG_PM - -static struct sleep_save s3c244x_sleep[] = { - SAVE_ITEM(S3C2440_DSC0), - SAVE_ITEM(S3C2440_DSC1), - SAVE_ITEM(S3C2440_GPJDAT), - SAVE_ITEM(S3C2440_GPJCON), - SAVE_ITEM(S3C2440_GPJUP) -}; - -static int s3c244x_suspend(struct sys_device *dev, pm_message_t state) -{ - s3c2410_pm_do_save(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep)); - return 0; -} - -static int s3c244x_resume(struct sys_device *dev) -{ - s3c2410_pm_do_restore(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep)); - return 0; -} - -#else -#define s3c244x_suspend NULL -#define s3c244x_resume NULL -#endif - -/* Since the S3C2442 and S3C2440 share items, put both sysclasses here */ - -struct sysdev_class s3c2440_sysclass = { - set_kset_name("s3c2440-core"), - .suspend = s3c244x_suspend, - .resume = s3c244x_resume -}; - -struct sysdev_class s3c2442_sysclass = { - set_kset_name("s3c2442-core"), - .suspend = s3c244x_suspend, - .resume = s3c244x_resume -}; - -/* need to register class before we actually register the device, and - * we also need to ensure that it has been initialised before any of the - * drivers even try to use it (even if not on an s3c2440 based system) - * as a driver which may support both 2410 and 2440 may try and use it. -*/ - -static int __init s3c2440_core_init(void) -{ - return sysdev_class_register(&s3c2440_sysclass); -} - -core_initcall(s3c2440_core_init); - -static int __init s3c2442_core_init(void) -{ - return sysdev_class_register(&s3c2442_sysclass); -} - -core_initcall(s3c2442_core_init); diff --git a/arch/arm/mach-s3c2410/s3c244x.h b/arch/arm/mach-s3c2410/s3c244x.h deleted file mode 100644 index 1488c1eb37e6..000000000000 --- a/arch/arm/mach-s3c2410/s3c244x.h +++ /dev/null @@ -1,25 +0,0 @@ -/* arch/arm/mach-s3c2410/s3c244x.h - * - * Copyright (c) 2004-2005 Simtec Electronics - * Ben Dooks - * - * Header file for S3C2440 and S3C2442 cpu support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) - -extern void s3c244x_map_io(struct map_desc *mach_desc, int size); - -extern void s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no); - -extern void s3c244x_init_clocks(int xtal); - -#else -#define s3c244x_init_clocks NULL -#define s3c244x_init_uarts NULL -#define s3c244x_map_io NULL -#endif diff --git a/arch/arm/mach-s3c2410/sleep.S b/arch/arm/mach-s3c2410/sleep.S index 2018c2e1dcc5..9179a1024588 100644 --- a/arch/arm/mach-s3c2410/sleep.S +++ b/arch/arm/mach-s3c2410/sleep.S @@ -1,4 +1,4 @@ -/* linux/arch/arm/mach-s3c2410/sleep.S +/* linux/arch/arm/mach-s3c2410/s3c2410-sleep.S * * Copyright (c) 2004 Simtec Electronics * Ben Dooks @@ -34,126 +34,35 @@ #include #include -/* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not - * reset the UART configuration, only enable if you really need this! -*/ -//#define CONFIG_DEBUG_RESUME - - .text - - /* s3c2410_cpu_save - * - * save enough of the CPU state to allow us to re-start - * pm.c code. as we store items like the sp/lr, we will - * end up returning from this function when the cpu resumes - * so the return value is set to mark this. - * - * This arangement means we avoid having to flush the cache - * from this code. - * - * entry: - * r0 = pointer to save block - * - * exit: - * r0 = 0 => we stored everything - * 1 => resumed from sleep - */ - -ENTRY(s3c2410_cpu_save) - stmfd sp!, { r4 - r12, lr } - - @@ store co-processor registers - - mrc p15, 0, r4, c15, c1, 0 @ CP access register - mrc p15, 0, r5, c13, c0, 0 @ PID - mrc p15, 0, r6, c3, c0, 0 @ Domain ID - mrc p15, 0, r7, c2, c0, 0 @ translation table base address - mrc p15, 0, r8, c1, c0, 0 @ control register - - stmia r0, { r4 - r13 } - - mov r0, #0 - ldmfd sp, { r4 - r12, pc } - - @@ return to the caller, after having the MMU - @@ turned on, this restores the last bits from the - @@ stack -resume_with_mmu: - mov r0, #1 - ldmfd sp!, { r4 - r12, pc } - - .ltorg - - @@ the next bits sit in the .data segment, even though they - @@ happen to be code... the s3c2410_sleep_save_phys needs to be - @@ accessed by the resume code before it can restore the MMU. - @@ This means that the variable has to be close enough for the - @@ code to read it... since the .text segment needs to be RO, - @@ the data segment can be the only place to put this code. - - .data - - .global s3c2410_sleep_save_phys -s3c2410_sleep_save_phys: - .word 0 - - /* s3c2410_cpu_resume + /* s3c2410_cpu_suspend * - * resume code entry for bootloader to call - * - * we must put this code here in the data segment as we have no - * other way of restoring the stack pointer after sleep, and we - * must not write to the code segment (code is read-only) + * put the cpu into sleep mode */ -ENTRY(s3c2410_cpu_resume) - mov r0, #PSR_I_BIT | PSR_F_BIT | SVC_MODE - msr cpsr_c, r0 - - @@ load UART to allow us to print the two characters for - @@ resume debug - - mov r2, #S3C24XX_PA_UART & 0xff000000 - orr r2, r2, #S3C24XX_PA_UART & 0xff000 - -#if 0 - /* SMDK2440 LED set */ - mov r14, #S3C24XX_PA_GPIO - ldr r12, [ r14, #0x54 ] - bic r12, r12, #3<<4 - orr r12, r12, #1<<7 - str r12, [ r14, #0x54 ] -#endif - -#ifdef CONFIG_DEBUG_RESUME - mov r3, #'L' - strb r3, [ r2, #S3C2410_UTXH ] -1001: - ldrb r14, [ r3, #S3C2410_UTRSTAT ] - tst r14, #S3C2410_UTRSTAT_TXE - beq 1001b -#endif /* CONFIG_DEBUG_RESUME */ - - mov r1, #0 - mcr p15, 0, r1, c8, c7, 0 @@ invalidate I & D TLBs - mcr p15, 0, r1, c7, c7, 0 @@ invalidate I & D caches - - ldr r0, s3c2410_sleep_save_phys @ address of restore block - ldmia r0, { r4 - r13 } - - mcr p15, 0, r4, c15, c1, 0 @ CP access register - mcr p15, 0, r5, c13, c0, 0 @ PID - mcr p15, 0, r6, c3, c0, 0 @ Domain ID - mcr p15, 0, r7, c2, c0, 0 @ translation table base - -#ifdef CONFIG_DEBUG_RESUME - mov r3, #'R' - strb r3, [ r2, #S3C2410_UTXH ] -#endif - - ldr r2, =resume_with_mmu - mcr p15, 0, r8, c1, c0, 0 @ turn on MMU, etc - nop @ second-to-last before mmu - mov pc, r2 @ go back to virtual address - - .ltorg +ENTRY(s3c2410_cpu_suspend) + @@ prepare cpu to sleep + + ldr r4, =S3C2410_REFRESH + ldr r5, =S3C24XX_MISCCR + ldr r6, =S3C2410_CLKCON + ldr r7, [ r4 ] @ get REFRESH (and ensure in TLB) + ldr r8, [ r5 ] @ get MISCCR (and ensure in TLB) + ldr r9, [ r6 ] @ get CLKCON (and ensure in TLB) + + orr r7, r7, #S3C2410_REFRESH_SELF @ SDRAM sleep command + orr r8, r8, #S3C2410_MISCCR_SDSLEEP @ SDRAM power-down signals + orr r9, r9, #S3C2410_CLKCON_POWER @ power down command + + teq pc, #0 @ first as a trial-run to load cache + bl s3c2410_do_sleep + teq r0, r0 @ now do it for real + b s3c2410_do_sleep @ + + @@ align next bit of code to cache line + .align 8 +s3c2410_do_sleep: + streq r7, [ r4 ] @ SDRAM sleep command + streq r8, [ r5 ] @ SDRAM power-down config + streq r9, [ r6 ] @ CPU sleep +1: beq 1b + mov pc, r14 diff --git a/arch/arm/mach-s3c2410/time.c b/arch/arm/mach-s3c2410/time.c deleted file mode 100644 index 9910bf0f2cea..000000000000 --- a/arch/arm/mach-s3c2410/time.c +++ /dev/null @@ -1,262 +0,0 @@ -/* linux/arch/arm/mach-s3c2410/time.c - * - * Copyright (C) 2003-2005 Simtec Electronics - * Ben Dooks, - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include -#include -#include - -#include "clock.h" -#include "cpu.h" - -static unsigned long timer_startval; -static unsigned long timer_usec_ticks; - -#define TIMER_USEC_SHIFT 16 - -/* we use the shifted arithmetic to work out the ratio of timer ticks - * to usecs, as often the peripheral clock is not a nice even multiple - * of 1MHz. - * - * shift of 14 and 15 are too low for the 12MHz, 16 seems to be ok - * for the current HZ value of 200 without producing overflows. - * - * Original patch by Dimitry Andric, updated by Ben Dooks -*/ - - -/* timer_mask_usec_ticks - * - * given a clock and divisor, make the value to pass into timer_ticks_to_usec - * to scale the ticks into usecs -*/ - -static inline unsigned long -timer_mask_usec_ticks(unsigned long scaler, unsigned long pclk) -{ - unsigned long den = pclk / 1000; - - return ((1000 << TIMER_USEC_SHIFT) * scaler + (den >> 1)) / den; -} - -/* timer_ticks_to_usec - * - * convert timer ticks to usec. -*/ - -static inline unsigned long timer_ticks_to_usec(unsigned long ticks) -{ - unsigned long res; - - res = ticks * timer_usec_ticks; - res += 1 << (TIMER_USEC_SHIFT - 4); /* round up slightly */ - - return res >> TIMER_USEC_SHIFT; -} - -/*** - * Returns microsecond since last clock interrupt. Note that interrupts - * will have been disabled by do_gettimeoffset() - * IRQs are disabled before entering here from do_gettimeofday() - */ - -#define SRCPND_TIMER4 (1<<(IRQ_TIMER4 - IRQ_EINT0)) - -static unsigned long s3c2410_gettimeoffset (void) -{ - unsigned long tdone; - unsigned long irqpend; - unsigned long tval; - - /* work out how many ticks have gone since last timer interrupt */ - - tval = __raw_readl(S3C2410_TCNTO(4)); - tdone = timer_startval - tval; - - /* check to see if there is an interrupt pending */ - - irqpend = __raw_readl(S3C2410_SRCPND); - if (irqpend & SRCPND_TIMER4) { - /* re-read the timer, and try and fix up for the missed - * interrupt. Note, the interrupt may go off before the - * timer has re-loaded from wrapping. - */ - - tval = __raw_readl(S3C2410_TCNTO(4)); - tdone = timer_startval - tval; - - if (tval != 0) - tdone += timer_startval; - } - - return timer_ticks_to_usec(tdone); -} - - -/* - * IRQ handler for the timer - */ -static irqreturn_t -s3c2410_timer_interrupt(int irq, void *dev_id) -{ - write_seqlock(&xtime_lock); - timer_tick(); - write_sequnlock(&xtime_lock); - return IRQ_HANDLED; -} - -static struct irqaction s3c2410_timer_irq = { - .name = "S3C2410 Timer Tick", - .flags = IRQF_DISABLED | IRQF_TIMER, - .handler = s3c2410_timer_interrupt, -}; - -#define use_tclk1_12() ( \ - machine_is_bast() || \ - machine_is_vr1000() || \ - machine_is_anubis() || \ - machine_is_osiris() ) - -/* - * Set up timer interrupt, and return the current time in seconds. - * - * Currently we only use timer4, as it is the only timer which has no - * other function that can be exploited externally - */ -static void s3c2410_timer_setup (void) -{ - unsigned long tcon; - unsigned long tcnt; - unsigned long tcfg1; - unsigned long tcfg0; - - tcnt = 0xffff; /* default value for tcnt */ - - /* read the current timer configuration bits */ - - tcon = __raw_readl(S3C2410_TCON); - tcfg1 = __raw_readl(S3C2410_TCFG1); - tcfg0 = __raw_readl(S3C2410_TCFG0); - - /* configure the system for whichever machine is in use */ - - if (use_tclk1_12()) { - /* timer is at 12MHz, scaler is 1 */ - timer_usec_ticks = timer_mask_usec_ticks(1, 12000000); - tcnt = 12000000 / HZ; - - tcfg1 &= ~S3C2410_TCFG1_MUX4_MASK; - tcfg1 |= S3C2410_TCFG1_MUX4_TCLK1; - } else { - unsigned long pclk; - struct clk *clk; - - /* for the h1940 (and others), we use the pclk from the core - * to generate the timer values. since values around 50 to - * 70MHz are not values we can directly generate the timer - * value from, we need to pre-scale and divide before using it. - * - * for instance, using 50.7MHz and dividing by 6 gives 8.45MHz - * (8.45 ticks per usec) - */ - - /* this is used as default if no other timer can be found */ - - clk = clk_get(NULL, "timers"); - if (IS_ERR(clk)) - panic("failed to get clock for system timer"); - - clk_enable(clk); - - pclk = clk_get_rate(clk); - - /* configure clock tick */ - - timer_usec_ticks = timer_mask_usec_ticks(6, pclk); - - tcfg1 &= ~S3C2410_TCFG1_MUX4_MASK; - tcfg1 |= S3C2410_TCFG1_MUX4_DIV2; - - tcfg0 &= ~S3C2410_TCFG_PRESCALER1_MASK; - tcfg0 |= ((6 - 1) / 2) << S3C2410_TCFG_PRESCALER1_SHIFT; - - tcnt = (pclk / 6) / HZ; - } - - /* timers reload after counting zero, so reduce the count by 1 */ - - tcnt--; - - printk("timer tcon=%08lx, tcnt %04lx, tcfg %08lx,%08lx, usec %08lx\n", - tcon, tcnt, tcfg0, tcfg1, timer_usec_ticks); - - /* check to see if timer is within 16bit range... */ - if (tcnt > 0xffff) { - panic("setup_timer: HZ is too small, cannot configure timer!"); - return; - } - - __raw_writel(tcfg1, S3C2410_TCFG1); - __raw_writel(tcfg0, S3C2410_TCFG0); - - timer_startval = tcnt; - __raw_writel(tcnt, S3C2410_TCNTB(4)); - - /* ensure timer is stopped... */ - - tcon &= ~(7<<20); - tcon |= S3C2410_TCON_T4RELOAD; - tcon |= S3C2410_TCON_T4MANUALUPD; - - __raw_writel(tcon, S3C2410_TCON); - __raw_writel(tcnt, S3C2410_TCNTB(4)); - __raw_writel(tcnt, S3C2410_TCMPB(4)); - - /* start the timer running */ - tcon |= S3C2410_TCON_T4START; - tcon &= ~S3C2410_TCON_T4MANUALUPD; - __raw_writel(tcon, S3C2410_TCON); -} - -static void __init s3c2410_timer_init (void) -{ - s3c2410_timer_setup(); - setup_irq(IRQ_TIMER4, &s3c2410_timer_irq); -} - -struct sys_timer s3c24xx_timer = { - .init = s3c2410_timer_init, - .offset = s3c2410_gettimeoffset, - .resume = s3c2410_timer_setup -}; diff --git a/arch/arm/mach-s3c2410/usb-simtec.c b/arch/arm/mach-s3c2410/usb-simtec.c index 22b0e1cdd4bf..bcd562ac1d3d 100644 --- a/arch/arm/mach-s3c2410/usb-simtec.c +++ b/arch/arm/mach-s3c2410/usb-simtec.c @@ -35,7 +35,7 @@ #include #include -#include "devs.h" +#include #include "usb-simtec.h" /* control power and monitor over-current events on various Simtec diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig new file mode 100644 index 000000000000..6d629de84cdb --- /dev/null +++ b/arch/arm/mach-s3c2412/Kconfig @@ -0,0 +1,58 @@ +# arch/arm/mach-s3c2412/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +config CPU_S3C2412 + bool + depends on ARCH_S3C2410 + select S3C2412_PM if PM + select S3C2412_DMA if S3C2410_DMA + help + Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line + +config CPU_S3C2412_ONLY + bool + depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \ + !CPU_S3C2440 && !CPU_S3C2442 && CPU_S3C2412 + default y if CPU_S3C2412 + +config S3C2412_DMA + bool + depends on CPU_S3C2412 + help + Internal config node for S3C2412 DMA support + +config S3C2412_PM + bool + help + Internal config node to apply S3C2412 power management + + +menu "S3C2412 Machines" + +config MACH_SMDK2413 + bool "SMDK2413" + select CPU_S3C2412 + select MACH_S3C2413 + select MACH_SMDK + help + Say Y here if you are using an SMDK2413 + +config MACH_S3C2413 + bool + help + Internal node for S3C2413 version of SMDK2413, so that + machine_is_s3c2413() will work when MACH_SMDK2413 is + selected + +config MACH_VSTMS + bool "VMSTMS" + select CPU_S3C2412 + help + Say Y here if you are using an VSTMS board + + +endmenu + diff --git a/arch/arm/mach-s3c2412/Makefile b/arch/arm/mach-s3c2412/Makefile new file mode 100644 index 000000000000..f8e011691b31 --- /dev/null +++ b/arch/arm/mach-s3c2412/Makefile @@ -0,0 +1,21 @@ +# arch/arm/mach-s3c2412/Makefile +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +obj-y := +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_CPU_S3C2412) += s3c2412.o +obj-$(CONFIG_CPU_S3C2412) += irq.o +obj-$(CONFIG_CPU_S3C2412) += clock.o +obj-$(CONFIG_S3C2412_DMA) += dma.o +obj-$(CONFIG_S3C2412_PM) += pm.o + +# Machine support + +obj-$(CONFIG_MACH_SMDK2413) += mach-smdk2413.o +obj-$(CONFIG_MACH_VSTMS) += mach-vstms.o diff --git a/arch/arm/mach-s3c2412/clock.c b/arch/arm/mach-s3c2412/clock.c new file mode 100644 index 000000000000..6a8e4448770b --- /dev/null +++ b/arch/arm/mach-s3c2412/clock.c @@ -0,0 +1,716 @@ +/* linux/arch/arm/mach-s3c2412/clock.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * S3C2412,S3C2413 Clock control support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include + +#include +#include +#include + +#include +#include +#include + +/* We currently have to assume that the system is running + * from the XTPll input, and that all ***REFCLKs are being + * fed from it, as we cannot read the state of OM[4] from + * software. + * + * It would be possible for each board initialisation to + * set the correct muxing at initialisation +*/ + +static int s3c2412_clkcon_enable(struct clk *clk, int enable) +{ + unsigned int clocks = clk->ctrlbit; + unsigned long clkcon; + + clkcon = __raw_readl(S3C2410_CLKCON); + + if (enable) + clkcon |= clocks; + else + clkcon &= ~clocks; + + __raw_writel(clkcon, S3C2410_CLKCON); + + return 0; +} + +static int s3c2412_upll_enable(struct clk *clk, int enable) +{ + unsigned long upllcon = __raw_readl(S3C2410_UPLLCON); + unsigned long orig = upllcon; + + if (!enable) + upllcon |= S3C2412_PLLCON_OFF; + else + upllcon &= ~S3C2412_PLLCON_OFF; + + __raw_writel(upllcon, S3C2410_UPLLCON); + + /* allow ~150uS for the PLL to settle and lock */ + + if (enable && (orig & S3C2412_PLLCON_OFF)) + udelay(150); + + return 0; +} + +/* clock selections */ + +/* CPU EXTCLK input */ +static struct clk clk_ext = { + .name = "extclk", + .id = -1, +}; + +static struct clk clk_erefclk = { + .name = "erefclk", + .id = -1, +}; + +static struct clk clk_urefclk = { + .name = "urefclk", + .id = -1, +}; + +static int s3c2412_setparent_usysclk(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + + if (parent == &clk_urefclk) + clksrc &= ~S3C2412_CLKSRC_USYSCLK_UPLL; + else if (parent == &clk_upll) + clksrc |= S3C2412_CLKSRC_USYSCLK_UPLL; + else + return -EINVAL; + + clk->parent = parent; + + __raw_writel(clksrc, S3C2412_CLKSRC); + return 0; +} + +static struct clk clk_usysclk = { + .name = "usysclk", + .id = -1, + .parent = &clk_xtal, + .set_parent = s3c2412_setparent_usysclk, +}; + +static struct clk clk_mrefclk = { + .name = "mrefclk", + .parent = &clk_xtal, + .id = -1, +}; + +static struct clk clk_mdivclk = { + .name = "mdivclk", + .parent = &clk_xtal, + .id = -1, +}; + +static int s3c2412_setparent_usbsrc(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + + if (parent == &clk_usysclk) + clksrc &= ~S3C2412_CLKSRC_USBCLK_HCLK; + else if (parent == &clk_h) + clksrc |= S3C2412_CLKSRC_USBCLK_HCLK; + else + return -EINVAL; + + clk->parent = parent; + + __raw_writel(clksrc, S3C2412_CLKSRC); + return 0; +} + +static unsigned long s3c2412_roundrate_usbsrc(struct clk *clk, + unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + int div; + + if (rate > parent_rate) + return parent_rate; + + div = parent_rate / rate; + if (div > 2) + div = 2; + + return parent_rate / div; +} + +static unsigned long s3c2412_getrate_usbsrc(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2410_CLKDIVN); + + return parent_rate / ((div & S3C2412_CLKDIVN_USB48DIV) ? 2 : 1); +} + +static int s3c2412_setrate_usbsrc(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); + + rate = s3c2412_roundrate_usbsrc(clk, rate); + + if ((parent_rate / rate) == 2) + clkdivn |= S3C2412_CLKDIVN_USB48DIV; + else + clkdivn &= ~S3C2412_CLKDIVN_USB48DIV; + + __raw_writel(clkdivn, S3C2410_CLKDIVN); + return 0; +} + +static struct clk clk_usbsrc = { + .name = "usbsrc", + .id = -1, + .get_rate = s3c2412_getrate_usbsrc, + .set_rate = s3c2412_setrate_usbsrc, + .round_rate = s3c2412_roundrate_usbsrc, + .set_parent = s3c2412_setparent_usbsrc, +}; + +static int s3c2412_setparent_msysclk(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + + if (parent == &clk_mdivclk) + clksrc &= ~S3C2412_CLKSRC_MSYSCLK_MPLL; + else if (parent == &clk_upll) + clksrc |= S3C2412_CLKSRC_MSYSCLK_MPLL; + else + return -EINVAL; + + clk->parent = parent; + + __raw_writel(clksrc, S3C2412_CLKSRC); + return 0; +} + +static struct clk clk_msysclk = { + .name = "msysclk", + .id = -1, + .set_parent = s3c2412_setparent_msysclk, +}; + +/* these next clocks have an divider immediately after them, + * so we can register them with their divider and leave out the + * intermediate clock stage +*/ +static unsigned long s3c2412_roundrate_clksrc(struct clk *clk, + unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + int div; + + if (rate > parent_rate) + return parent_rate; + + /* note, we remove the +/- 1 calculations as they cancel out */ + + div = (rate / parent_rate); + + if (div < 1) + div = 1; + else if (div > 16) + div = 16; + + return parent_rate / div; +} + +static int s3c2412_setparent_uart(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + + if (parent == &clk_erefclk) + clksrc &= ~S3C2412_CLKSRC_UARTCLK_MPLL; + else if (parent == &clk_mpll) + clksrc |= S3C2412_CLKSRC_UARTCLK_MPLL; + else + return -EINVAL; + + clk->parent = parent; + + __raw_writel(clksrc, S3C2412_CLKSRC); + return 0; +} + +static unsigned long s3c2412_getrate_uart(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2410_CLKDIVN); + + div &= S3C2412_CLKDIVN_UARTDIV_MASK; + div >>= S3C2412_CLKDIVN_UARTDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2412_setrate_uart(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); + + rate = s3c2412_roundrate_clksrc(clk, rate); + + clkdivn &= ~S3C2412_CLKDIVN_UARTDIV_MASK; + clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_UARTDIV_SHIFT; + + __raw_writel(clkdivn, S3C2410_CLKDIVN); + return 0; +} + +static struct clk clk_uart = { + .name = "uartclk", + .id = -1, + .get_rate = s3c2412_getrate_uart, + .set_rate = s3c2412_setrate_uart, + .set_parent = s3c2412_setparent_uart, + .round_rate = s3c2412_roundrate_clksrc, +}; + +static int s3c2412_setparent_i2s(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + + if (parent == &clk_erefclk) + clksrc &= ~S3C2412_CLKSRC_I2SCLK_MPLL; + else if (parent == &clk_mpll) + clksrc |= S3C2412_CLKSRC_I2SCLK_MPLL; + else + return -EINVAL; + + clk->parent = parent; + + __raw_writel(clksrc, S3C2412_CLKSRC); + return 0; +} + +static unsigned long s3c2412_getrate_i2s(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2410_CLKDIVN); + + div &= S3C2412_CLKDIVN_I2SDIV_MASK; + div >>= S3C2412_CLKDIVN_I2SDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2412_setrate_i2s(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); + + rate = s3c2412_roundrate_clksrc(clk, rate); + + clkdivn &= ~S3C2412_CLKDIVN_I2SDIV_MASK; + clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_I2SDIV_SHIFT; + + __raw_writel(clkdivn, S3C2410_CLKDIVN); + return 0; +} + +static struct clk clk_i2s = { + .name = "i2sclk", + .id = -1, + .get_rate = s3c2412_getrate_i2s, + .set_rate = s3c2412_setrate_i2s, + .set_parent = s3c2412_setparent_i2s, + .round_rate = s3c2412_roundrate_clksrc, +}; + +static int s3c2412_setparent_cam(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + + if (parent == &clk_usysclk) + clksrc &= ~S3C2412_CLKSRC_CAMCLK_HCLK; + else if (parent == &clk_h) + clksrc |= S3C2412_CLKSRC_CAMCLK_HCLK; + else + return -EINVAL; + + clk->parent = parent; + + __raw_writel(clksrc, S3C2412_CLKSRC); + return 0; +} +static unsigned long s3c2412_getrate_cam(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2410_CLKDIVN); + + div &= S3C2412_CLKDIVN_CAMDIV_MASK; + div >>= S3C2412_CLKDIVN_CAMDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2412_setrate_cam(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); + + rate = s3c2412_roundrate_clksrc(clk, rate); + + clkdivn &= ~S3C2412_CLKDIVN_CAMDIV_MASK; + clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_CAMDIV_SHIFT; + + __raw_writel(clkdivn, S3C2410_CLKDIVN); + return 0; +} + +static struct clk clk_cam = { + .name = "camif-upll", /* same as 2440 name */ + .id = -1, + .get_rate = s3c2412_getrate_cam, + .set_rate = s3c2412_setrate_cam, + .set_parent = s3c2412_setparent_cam, + .round_rate = s3c2412_roundrate_clksrc, +}; + +/* standard clock definitions */ + +static struct clk init_clocks_disable[] = { + { + .name = "nand", + .id = -1, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_NAND, + }, { + .name = "sdi", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_SDI, + }, { + .name = "adc", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_ADC, + }, { + .name = "i2c", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_IIC, + }, { + .name = "iis", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_IIS, + }, { + .name = "spi", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_SPI, + } +}; + +static struct clk init_clocks[] = { + { + .name = "dma", + .id = 0, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_DMA0, + }, { + .name = "dma", + .id = 1, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_DMA1, + }, { + .name = "dma", + .id = 2, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_DMA2, + }, { + .name = "dma", + .id = 3, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_DMA3, + }, { + .name = "lcd", + .id = -1, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_LCDC, + }, { + .name = "gpio", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_GPIO, + }, { + .name = "usb-host", + .id = -1, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_USBH, + }, { + .name = "usb-device", + .id = -1, + .parent = &clk_h, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_USBD, + }, { + .name = "timers", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_PWMT, + }, { + .name = "uart", + .id = 0, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_UART0, + }, { + .name = "uart", + .id = 1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_UART1, + }, { + .name = "uart", + .id = 2, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_UART2, + }, { + .name = "rtc", + .id = -1, + .parent = &clk_p, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_RTC, + }, { + .name = "watchdog", + .id = -1, + .parent = &clk_p, + .ctrlbit = 0, + }, { + .name = "usb-bus-gadget", + .id = -1, + .parent = &clk_usb_bus, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_USB_DEV48, + }, { + .name = "usb-bus-host", + .id = -1, + .parent = &clk_usb_bus, + .enable = s3c2412_clkcon_enable, + .ctrlbit = S3C2412_CLKCON_USB_HOST48, + } +}; + +/* clocks to add where we need to check their parentage */ + +struct clk_init { + struct clk *clk; + unsigned int bit; + struct clk *src_0; + struct clk *src_1; +}; + +static struct clk_init clks_src[] __initdata = { + { + .clk = &clk_usysclk, + .bit = S3C2412_CLKSRC_USBCLK_HCLK, + .src_0 = &clk_urefclk, + .src_1 = &clk_upll, + }, { + .clk = &clk_i2s, + .bit = S3C2412_CLKSRC_I2SCLK_MPLL, + .src_0 = &clk_erefclk, + .src_1 = &clk_mpll, + }, { + .clk = &clk_cam, + .bit = S3C2412_CLKSRC_CAMCLK_HCLK, + .src_0 = &clk_usysclk, + .src_1 = &clk_h, + }, { + .clk = &clk_msysclk, + .bit = S3C2412_CLKSRC_MSYSCLK_MPLL, + .src_0 = &clk_mdivclk, + .src_1 = &clk_mpll, + }, { + .clk = &clk_uart, + .bit = S3C2412_CLKSRC_UARTCLK_MPLL, + .src_0 = &clk_erefclk, + .src_1 = &clk_mpll, + }, { + .clk = &clk_usbsrc, + .bit = S3C2412_CLKSRC_USBCLK_HCLK, + .src_0 = &clk_usysclk, + .src_1 = &clk_h, + }, +}; + +/* s3c2412_clk_initparents + * + * Initialise the parents for the clocks that we get at start-time +*/ + +static void __init s3c2412_clk_initparents(void) +{ + unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); + struct clk_init *cip = clks_src; + struct clk *src; + int ptr; + int ret; + + for (ptr = 0; ptr < ARRAY_SIZE(clks_src); ptr++, cip++) { + ret = s3c24xx_register_clock(cip->clk); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + cip->clk->name, ret); + } + + src = (clksrc & cip->bit) ? cip->src_1 : cip->src_0; + + printk(KERN_INFO "%s: parent %s\n", cip->clk->name, src->name); + clk_set_parent(cip->clk, src); + } +} + +/* clocks to add straight away */ + +static struct clk *clks[] __initdata = { + &clk_ext, + &clk_usb_bus, + &clk_erefclk, + &clk_urefclk, + &clk_mrefclk, +}; + +int __init s3c2412_baseclk_add(void) +{ + unsigned long clkcon = __raw_readl(S3C2410_CLKCON); + struct clk *clkp; + int ret; + int ptr; + + clk_upll.enable = s3c2412_upll_enable; + clk_usb_bus.parent = &clk_usbsrc; + clk_usb_bus.rate = 0x0; + + s3c2412_clk_initparents(); + + for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) { + clkp = clks[ptr]; + + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + } + + /* ensure usb bus clock is within correct rate of 48MHz */ + + if (clk_get_rate(&clk_usb_bus) != (48 * 1000 * 1000)) { + printk(KERN_INFO "Warning: USB bus clock not at 48MHz\n"); + + /* for the moment, let's use the UPLL, and see if we can + * get 48MHz */ + + clk_set_parent(&clk_usysclk, &clk_upll); + clk_set_parent(&clk_usbsrc, &clk_usysclk); + clk_set_rate(&clk_usbsrc, 48*1000*1000); + } + + printk("S3C2412: upll %s, %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n", + (__raw_readl(S3C2410_UPLLCON) & S3C2412_PLLCON_OFF) ? "off":"on", + print_mhz(clk_get_rate(&clk_upll)), + print_mhz(clk_get_rate(&clk_usb_bus))); + + /* register clocks from clock array */ + + clkp = init_clocks; + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { + /* ensure that we note the clock state */ + + clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; + + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + } + + /* We must be careful disabling the clocks we are not intending to + * be using at boot time, as subsytems such as the LCD which do + * their own DMA requests to the bus can cause the system to lockup + * if they where in the middle of requesting bus access. + * + * Disabling the LCD clock if the LCD is active is very dangerous, + * and therefore the bootloader should be careful to not enable + * the LCD clock if it is not needed. + */ + + /* install (and disable) the clocks we do not need immediately */ + + clkp = init_clocks_disable; + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) { + + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + + s3c2412_clkcon_enable(clkp, 0); + } + + return 0; +} diff --git a/arch/arm/mach-s3c2412/dma.c b/arch/arm/mach-s3c2412/dma.c new file mode 100644 index 000000000000..28b598287fae --- /dev/null +++ b/arch/arm/mach-s3c2412/dma.c @@ -0,0 +1,161 @@ +/* linux/arch/arm/mach-s3c2412/dma.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * S3C2412 DMA selection + * + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#define MAP(x) { (x)| DMA_CH_VALID, (x)| DMA_CH_VALID, (x)| DMA_CH_VALID, (x)| DMA_CH_VALID } + +static struct s3c24xx_dma_map __initdata s3c2412_dma_mappings[] = { + [DMACH_XD0] = { + .name = "xdreq0", + .channels = MAP(S3C2412_DMAREQSEL_XDREQ0), + }, + [DMACH_XD1] = { + .name = "xdreq1", + .channels = MAP(S3C2412_DMAREQSEL_XDREQ1), + }, + [DMACH_SDI] = { + .name = "sdi", + .channels = MAP(S3C2412_DMAREQSEL_SDI), + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_SPI0] = { + .name = "spi0", + .channels = MAP(S3C2412_DMAREQSEL_SPI0TX), + .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, + }, + [DMACH_SPI1] = { + .name = "spi1", + .channels = MAP(S3C2412_DMAREQSEL_SPI1TX), + .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, + }, + [DMACH_UART0] = { + .name = "uart0", + .channels = MAP(S3C2412_DMAREQSEL_UART0_0), + .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, + }, + [DMACH_UART1] = { + .name = "uart1", + .channels = MAP(S3C2412_DMAREQSEL_UART1_0), + .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, + }, + [DMACH_UART2] = { + .name = "uart2", + .channels = MAP(S3C2412_DMAREQSEL_UART2_0), + .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, + }, + [DMACH_UART0_SRC2] = { + .name = "uart0", + .channels = MAP(S3C2412_DMAREQSEL_UART0_1), + .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, + }, + [DMACH_UART1_SRC2] = { + .name = "uart1", + .channels = MAP(S3C2412_DMAREQSEL_UART1_1), + .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, + }, + [DMACH_UART2_SRC2] = { + .name = "uart2", + .channels = MAP(S3C2412_DMAREQSEL_UART2_1), + .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, + }, + [DMACH_TIMER] = { + .name = "timer", + .channels = MAP(S3C2412_DMAREQSEL_TIMER), + }, + [DMACH_I2S_IN] = { + .name = "i2s-sdi", + .channels = MAP(S3C2412_DMAREQSEL_I2SRX), + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_I2S_OUT] = { + .name = "i2s-sdo", + .channels = MAP(S3C2412_DMAREQSEL_I2STX), + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_USB_EP1] = { + .name = "usb-ep1", + .channels = MAP(S3C2412_DMAREQSEL_USBEP1), + }, + [DMACH_USB_EP2] = { + .name = "usb-ep2", + .channels = MAP(S3C2412_DMAREQSEL_USBEP2), + }, + [DMACH_USB_EP3] = { + .name = "usb-ep3", + .channels = MAP(S3C2412_DMAREQSEL_USBEP3), + }, + [DMACH_USB_EP4] = { + .name = "usb-ep4", + .channels = MAP(S3C2412_DMAREQSEL_USBEP4), + }, +}; + +static void s3c2412_dma_select(struct s3c2410_dma_chan *chan, + struct s3c24xx_dma_map *map) +{ + writel(map->channels[0] | S3C2412_DMAREQSEL_HW, + chan->regs + S3C2412_DMA_DMAREQSEL); +} + +static struct s3c24xx_dma_selection __initdata s3c2412_dma_sel = { + .select = s3c2412_dma_select, + .dcon_mask = 0, + .map = s3c2412_dma_mappings, + .map_size = ARRAY_SIZE(s3c2412_dma_mappings), +}; + +static int s3c2412_dma_add(struct sys_device *sysdev) +{ + return s3c24xx_dma_init_map(&s3c2412_dma_sel); +} + +static struct sysdev_driver s3c2412_dma_driver = { + .add = s3c2412_dma_add, +}; + +static int __init s3c2412_dma_init(void) +{ + return sysdev_driver_register(&s3c2412_sysclass, &s3c2412_dma_driver); +} + +arch_initcall(s3c2412_dma_init); diff --git a/arch/arm/mach-s3c2412/irq.c b/arch/arm/mach-s3c2412/irq.c new file mode 100644 index 000000000000..e89dbdcb1b7b --- /dev/null +++ b/arch/arm/mach-s3c2412/irq.c @@ -0,0 +1,133 @@ +/* linux/arch/arm/mach-s3c2412/irq.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * +*/ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include + +#include +#include +#include + +/* the s3c2412 changes the behaviour of IRQ_EINT0 through IRQ_EINT3 by + * having them turn up in both the INT* and the EINT* registers. Whilst + * both show the status, they both now need to be acked when the IRQs + * go off. +*/ + +static void +s3c2412_irq_mask(unsigned int irqno) +{ + unsigned long bitval = 1UL << (irqno - IRQ_EINT0); + unsigned long mask; + + mask = __raw_readl(S3C2410_INTMSK); + __raw_writel(mask | bitval, S3C2410_INTMSK); + + mask = __raw_readl(S3C2412_EINTMASK); + __raw_writel(mask | bitval, S3C2412_EINTMASK); +} + +static inline void +s3c2412_irq_ack(unsigned int irqno) +{ + unsigned long bitval = 1UL << (irqno - IRQ_EINT0); + + __raw_writel(bitval, S3C2412_EINTPEND); + __raw_writel(bitval, S3C2410_SRCPND); + __raw_writel(bitval, S3C2410_INTPND); +} + +static inline void +s3c2412_irq_maskack(unsigned int irqno) +{ + unsigned long bitval = 1UL << (irqno - IRQ_EINT0); + unsigned long mask; + + mask = __raw_readl(S3C2410_INTMSK); + __raw_writel(mask|bitval, S3C2410_INTMSK); + + mask = __raw_readl(S3C2412_EINTMASK); + __raw_writel(mask | bitval, S3C2412_EINTMASK); + + __raw_writel(bitval, S3C2412_EINTPEND); + __raw_writel(bitval, S3C2410_SRCPND); + __raw_writel(bitval, S3C2410_INTPND); +} + +static void +s3c2412_irq_unmask(unsigned int irqno) +{ + unsigned long bitval = 1UL << (irqno - IRQ_EINT0); + unsigned long mask; + + mask = __raw_readl(S3C2412_EINTMASK); + __raw_writel(mask & ~bitval, S3C2412_EINTMASK); + + mask = __raw_readl(S3C2410_INTMSK); + __raw_writel(mask & ~bitval, S3C2410_INTMSK); +} + +static struct irq_chip s3c2412_irq_eint0t4 = { + .ack = s3c2412_irq_ack, + .mask = s3c2412_irq_mask, + .unmask = s3c2412_irq_unmask, + .set_wake = s3c_irq_wake, + .set_type = s3c_irqext_type, +}; + +static int s3c2412_irq_add(struct sys_device *sysdev) +{ + unsigned int irqno; + + for (irqno = IRQ_EINT0; irqno <= IRQ_EINT3; irqno++) { + set_irq_chip(irqno, &s3c2412_irq_eint0t4); + set_irq_handler(irqno, handle_edge_irq); + set_irq_flags(irqno, IRQF_VALID); + } + + return 0; +} + +static struct sysdev_driver s3c2412_irq_driver = { + .add = s3c2412_irq_add, + .suspend = s3c24xx_irq_suspend, + .resume = s3c24xx_irq_resume, +}; + +static int s3c2412_irq_init(void) +{ + return sysdev_driver_register(&s3c2412_sysclass, &s3c2412_irq_driver); +} + +arch_initcall(s3c2412_irq_init); diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c new file mode 100644 index 000000000000..32b15617ef2a --- /dev/null +++ b/arch/arm/mach-s3c2412/mach-smdk2413.c @@ -0,0 +1,140 @@ +/* linux/arch/arm/mach-s3c2412/mach-smdk2413.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * Thanks to Dimity Andric (TomTom) and Steven Ryu (Samsung) for the + * loans of SMDK2413 to work with. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +//#include +#include +#include +#include + +#include +#include + +#include +#include +#include +#include +#include + +#include + +static struct map_desc smdk2413_iodesc[] __initdata = { +}; + +static struct s3c2410_uartcfg smdk2413_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + /* IR port */ + [2] = { + .hwport = 2, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x43, + .ufcon = 0x51, + } +}; + +static struct platform_device *smdk2413_devices[] __initdata = { + &s3c_device_usb, + //&s3c_device_lcd, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, +}; + +static struct s3c24xx_board smdk2413_board __initdata = { + .devices = smdk2413_devices, + .devices_count = ARRAY_SIZE(smdk2413_devices) +}; + +static void __init smdk2413_fixup(struct machine_desc *desc, + struct tag *tags, char **cmdline, + struct meminfo *mi) +{ + if (tags != phys_to_virt(S3C2410_SDRAM_PA + 0x100)) { + mi->nr_banks=1; + mi->bank[0].start = 0x30000000; + mi->bank[0].size = SZ_64M; + mi->bank[0].node = 0; + } +} + +static void __init smdk2413_map_io(void) +{ + s3c24xx_init_io(smdk2413_iodesc, ARRAY_SIZE(smdk2413_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(smdk2413_uartcfgs, ARRAY_SIZE(smdk2413_uartcfgs)); + s3c24xx_set_board(&smdk2413_board); +} + +static void __init smdk2413_machine_init(void) +{ + smdk_machine_init(); +} + +MACHINE_START(S3C2413, "S3C2413") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .fixup = smdk2413_fixup, + .init_irq = s3c24xx_init_irq, + .map_io = smdk2413_map_io, + .init_machine = smdk2413_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END + +MACHINE_START(SMDK2413, "SMDK2413") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .fixup = smdk2413_fixup, + .init_irq = s3c24xx_init_irq, + .map_io = smdk2413_map_io, + .init_machine = smdk2413_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2412/mach-vstms.c b/arch/arm/mach-s3c2412/mach-vstms.c new file mode 100644 index 000000000000..f1afb707ff16 --- /dev/null +++ b/arch/arm/mach-s3c2412/mach-vstms.c @@ -0,0 +1,169 @@ +/* linux/arch/arm/mach-s3c2412/mach-vstms.c + * + * (C) 2006 Thomas Gleixner + * + * Derived from mach-smdk2413.c - (C) 2006 Simtec Electronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include + +#include +#include +#include +#include +#include + + +static struct map_desc vstms_iodesc[] __initdata = { +}; + +static struct s3c2410_uartcfg vstms_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + } +}; + +static struct mtd_partition vstms_nand_part[] = { + [0] = { + .name = "Boot Agent", + .size = 0x7C000, + .offset = 0, + }, + [1] = { + .name = "UBoot Config", + .offset = 0x7C000, + .size = 0x4000, + }, + [2] = { + .name = "Kernel", + .offset = 0x80000, + .size = 0x200000, + }, + [3] = { + .name = "RFS", + .offset = 0x280000, + .size = 0x3d80000, + }, +}; + +static struct s3c2410_nand_set vstms_nand_sets[] = { + [0] = { + .name = "NAND", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(vstms_nand_part), + .partitions = vstms_nand_part, + }, +}; + +/* choose a set of timings which should suit most 512Mbit + * chips and beyond. +*/ + +static struct s3c2410_platform_nand vstms_nand_info = { + .tacls = 20, + .twrph0 = 60, + .twrph1 = 20, + .nr_sets = ARRAY_SIZE(vstms_nand_sets), + .sets = vstms_nand_sets, +}; + +static struct platform_device *vstms_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, + &s3c_device_rtc, + &s3c_device_nand, +}; + +static struct s3c24xx_board vstms_board __initdata = { + .devices = vstms_devices, + .devices_count = ARRAY_SIZE(vstms_devices) +}; + +static void __init vstms_fixup(struct machine_desc *desc, + struct tag *tags, char **cmdline, + struct meminfo *mi) +{ + if (tags != phys_to_virt(S3C2410_SDRAM_PA + 0x100)) { + mi->nr_banks=1; + mi->bank[0].start = 0x30000000; + mi->bank[0].size = SZ_64M; + mi->bank[0].node = 0; + } +} + +static void __init vstms_map_io(void) +{ + s3c_device_nand.dev.platform_data = &vstms_nand_info; + + s3c24xx_init_io(vstms_iodesc, ARRAY_SIZE(vstms_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(vstms_uartcfgs, ARRAY_SIZE(vstms_uartcfgs)); + s3c24xx_set_board(&vstms_board); +} + +MACHINE_START(VSTMS, "VSTMS") + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .fixup = vstms_fixup, + .init_irq = s3c24xx_init_irq, + .map_io = vstms_map_io, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2412/pm.c b/arch/arm/mach-s3c2412/pm.c new file mode 100644 index 000000000000..8988dac388a9 --- /dev/null +++ b/arch/arm/mach-s3c2412/pm.c @@ -0,0 +1,128 @@ +/* linux/arch/arm/mach-s3c2412/pm.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * http://armlinux.simtec.co.uk/. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include + +#include +#include + +#include + +static void s3c2412_cpu_suspend(void) +{ + unsigned long tmp; + + /* set our standby method to sleep */ + + tmp = __raw_readl(S3C2412_PWRCFG); + tmp |= S3C2412_PWRCFG_STANDBYWFI_SLEEP; + __raw_writel(tmp, S3C2412_PWRCFG); + + /* issue the standby signal into the pm unit. Note, we + * issue a write-buffer drain just in case */ + + tmp = 0; + + asm("b 1f\n\t" + ".align 5\n\t" + "1:\n\t" + "mcr p15, 0, %0, c7, c10, 4\n\t" + "mcr p15, 0, %0, c7, c0, 4" :: "r" (tmp)); + + /* we should never get past here */ + + panic("sleep resumed to originator?"); +} + +static void s3c2412_pm_prepare(void) +{ +} + +static int s3c2412_pm_add(struct sys_device *sysdev) +{ + pm_cpu_prep = s3c2412_pm_prepare; + pm_cpu_sleep = s3c2412_cpu_suspend; + + return 0; +} + +static struct sleep_save s3c2412_sleep[] = { + SAVE_ITEM(S3C2412_DSC0), + SAVE_ITEM(S3C2412_DSC1), + SAVE_ITEM(S3C2413_GPJDAT), + SAVE_ITEM(S3C2413_GPJCON), + SAVE_ITEM(S3C2413_GPJUP), + + /* save the PWRCFG to get back to original sleep method */ + + SAVE_ITEM(S3C2412_PWRCFG), + + /* save the sleep configuration anyway, just in case these + * get damaged during wakeup */ + + SAVE_ITEM(S3C2412_GPBSLPCON), + SAVE_ITEM(S3C2412_GPCSLPCON), + SAVE_ITEM(S3C2412_GPDSLPCON), + SAVE_ITEM(S3C2412_GPESLPCON), + SAVE_ITEM(S3C2412_GPFSLPCON), + SAVE_ITEM(S3C2412_GPGSLPCON), + SAVE_ITEM(S3C2412_GPHSLPCON), + SAVE_ITEM(S3C2413_GPJSLPCON), +}; + +static int s3c2412_pm_suspend(struct sys_device *dev, pm_message_t state) +{ + s3c2410_pm_do_save(s3c2412_sleep, ARRAY_SIZE(s3c2412_sleep)); + return 0; +} + +static int s3c2412_pm_resume(struct sys_device *dev) +{ + unsigned long tmp; + + tmp = __raw_readl(S3C2412_PWRCFG); + tmp &= ~S3C2412_PWRCFG_STANDBYWFI_MASK; + tmp |= S3C2412_PWRCFG_STANDBYWFI_IDLE; + __raw_writel(tmp, S3C2412_PWRCFG); + + s3c2410_pm_do_restore(s3c2412_sleep, ARRAY_SIZE(s3c2412_sleep)); + return 0; +} + +static struct sysdev_driver s3c2412_pm_driver = { + .add = s3c2412_pm_add, + .suspend = s3c2412_pm_suspend, + .resume = s3c2412_pm_resume, +}; + +static __init int s3c2412_pm_init(void) +{ + return sysdev_driver_register(&s3c2412_sysclass, &s3c2412_pm_driver); +} + +arch_initcall(s3c2412_pm_init); diff --git a/arch/arm/mach-s3c2412/s3c2412.c b/arch/arm/mach-s3c2412/s3c2412.c new file mode 100644 index 000000000000..aafe0bc593f1 --- /dev/null +++ b/arch/arm/mach-s3c2412/s3c2412.c @@ -0,0 +1,181 @@ +/* linux/arch/arm/mach-s3c2412/s3c2412.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * http://armlinux.simtec.co.uk/. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include + +#include + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#ifndef CONFIG_CPU_S3C2412_ONLY +void __iomem *s3c24xx_va_gpio2 = S3C24XX_VA_GPIO; + +static inline void s3c2412_init_gpio2(void) +{ + s3c24xx_va_gpio2 = S3C24XX_VA_GPIO + 0x10; +} +#else +#define s3c2412_init_gpio2() do { } while(0) +#endif + +/* Initial IO mappings */ + +static struct map_desc s3c2412_iodesc[] __initdata = { + IODESC_ENT(CLKPWR), + IODESC_ENT(LCD), + IODESC_ENT(TIMER), + IODESC_ENT(WATCHDOG), +}; + +/* uart registration process */ + +void __init s3c2412_init_uarts(struct s3c2410_uartcfg *cfg, int no) +{ + s3c24xx_init_uartdevs("s3c2412-uart", s3c2410_uart_resources, cfg, no); + + /* rename devices that are s3c2412/s3c2413 specific */ + s3c_device_sdi.name = "s3c2412-sdi"; + s3c_device_lcd.name = "s3c2412-lcd"; + s3c_device_nand.name = "s3c2412-nand"; +} + +/* s3c2412_idle + * + * use the standard idle call by ensuring the idle mode + * in power config, then issuing the idle co-processor + * instruction +*/ + +static void s3c2412_idle(void) +{ + unsigned long tmp; + + /* ensure our idle mode is to go to idle */ + + tmp = __raw_readl(S3C2412_PWRCFG); + tmp &= ~S3C2412_PWRCFG_STANDBYWFI_MASK; + tmp |= S3C2412_PWRCFG_STANDBYWFI_IDLE; + __raw_writel(tmp, S3C2412_PWRCFG); + + cpu_do_idle(); +} + +/* s3c2412_map_io + * + * register the standard cpu IO areas, and any passed in from the + * machine specific initialisation. +*/ + +void __init s3c2412_map_io(struct map_desc *mach_desc, int mach_size) +{ + /* move base of IO */ + + s3c2412_init_gpio2(); + + /* set our idle function */ + + s3c24xx_idle = s3c2412_idle; + + /* register our io-tables */ + + iotable_init(s3c2412_iodesc, ARRAY_SIZE(s3c2412_iodesc)); + iotable_init(mach_desc, mach_size); +} + +void __init s3c2412_init_clocks(int xtal) +{ + unsigned long tmp; + unsigned long fclk; + unsigned long hclk; + unsigned long pclk; + + /* now we've got our machine bits initialised, work out what + * clocks we've got */ + + fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal*2); + + tmp = __raw_readl(S3C2410_CLKDIVN); + + /* work out clock scalings */ + + hclk = fclk / ((tmp & S3C2412_CLKDIVN_HDIVN_MASK) + 1); + hclk /= ((tmp & S3C2421_CLKDIVN_ARMDIVN) ? 2 : 1); + pclk = hclk / ((tmp & S3C2412_CLKDIVN_PDIVN) ? 2 : 1); + + /* print brieft summary of clocks, etc */ + + printk("S3C2412: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", + print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); + + /* initialise the clocks here, to allow other things like the + * console to use them + */ + + s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); + s3c2412_baseclk_add(); +} + +/* need to register class before we actually register the device, and + * we also need to ensure that it has been initialised before any of the + * drivers even try to use it (even if not on an s3c2412 based system) + * as a driver which may support both 2410 and 2440 may try and use it. +*/ + +struct sysdev_class s3c2412_sysclass = { + set_kset_name("s3c2412-core"), +}; + +static int __init s3c2412_core_init(void) +{ + return sysdev_class_register(&s3c2412_sysclass); +} + +core_initcall(s3c2412_core_init); + +static struct sys_device s3c2412_sysdev = { + .cls = &s3c2412_sysclass, +}; + +int __init s3c2412_init(void) +{ + printk("S3C2412: Initialising architecture\n"); + + return sysdev_register(&s3c2412_sysdev); +} diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig new file mode 100644 index 000000000000..e3bfda098c0f --- /dev/null +++ b/arch/arm/mach-s3c2440/Kconfig @@ -0,0 +1,71 @@ +# arch/arm/mach-s3c2440/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +config CPU_S3C2440 + bool + depends on ARCH_S3C2410 + select S3C2410_CLOCK + select S3C2410_PM if PM + select S3C2410_GPIO + select S3C2440_DMA if S3C2410_DMA + select CPU_S3C244X + help + Support for S3C2440 Samsung Mobile CPU based systems. + +config S3C2440_DMA + bool + depends on ARCH_S3C2410 && CPU_S3C24405B + help + Support for S3C2440 specific DMA code5A + + +menu "S3C2440 Machines" + +config MACH_ANUBIS + bool "Simtec Electronics ANUBIS" + select CPU_S3C2440 + select PM_SIMTEC if PM + help + Say Y here if you are using the Simtec Electronics ANUBIS + development system + +config MACH_OSIRIS + bool "Simtec IM2440D20 (OSIRIS) module" + select CPU_S3C2440 + select PM_SIMTEC if PM + help + Say Y here if you are using the Simtec IM2440D20 module, also + known as the Osiris. + +config MACH_RX3715 + bool "HP iPAQ rx3715" + select CPU_S3C2440 + select PM_H1940 if PM + help + Say Y here if you are using the HP iPAQ rx3715. + +config ARCH_S3C2440 + bool "SMDK2440" + select CPU_S3C2440 + select MACH_SMDK + help + Say Y here if you are using the SMDK2440. + +config MACH_NEXCODER_2440 + bool "NexVision NEXCODER 2440 Light Board" + select CPU_S3C2440 + help + Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board + +config SMDK2440_CPU2440 + bool "SMDK2440 with S3C2440 CPU module" + depends on ARCH_S3C2440 + default y if ARCH_S3C2440 + select CPU_S3C2440 + + +endmenu + diff --git a/arch/arm/mach-s3c2440/Makefile b/arch/arm/mach-s3c2440/Makefile new file mode 100644 index 000000000000..c81ed6248dcb --- /dev/null +++ b/arch/arm/mach-s3c2440/Makefile @@ -0,0 +1,23 @@ +# arch/arm/mach-s3c2440/Makefile +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +obj-y := +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_CPU_S3C2440) += s3c2440.o dsc.o +obj-$(CONFIG_CPU_S3C2440) += irq.o +obj-$(CONFIG_CPU_S3C2440) += clock.o +obj-$(CONFIG_S3C2440_DMA) += dma.o + +# Machine support + +obj-$(CONFIG_MACH_ANUBIS) += mach-anubis.o +obj-$(CONFIG_MACH_OSIRIS) += mach-osiris.o +obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o +obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o +obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o diff --git a/arch/arm/mach-s3c2440/clock.c b/arch/arm/mach-s3c2440/clock.c new file mode 100644 index 000000000000..79e2ea4adaf3 --- /dev/null +++ b/arch/arm/mach-s3c2440/clock.c @@ -0,0 +1,170 @@ +/* linux/arch/arm/mach-s3c2440/clock.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C2440 Clock support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include + +#include +#include + +/* S3C2440 extended clock support */ + +static unsigned long s3c2440_camif_upll_round(struct clk *clk, + unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + int div; + + if (rate > parent_rate) + return parent_rate; + + /* note, we remove the +/- 1 calculations for the divisor */ + + div = (parent_rate / rate) / 2; + + if (div < 1) + div = 1; + else if (div > 16) + div = 16; + + return parent_rate / (div * 2); +} + +static int s3c2440_camif_upll_setrate(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); + + rate = s3c2440_camif_upll_round(clk, rate); + + camdivn &= ~(S3C2440_CAMDIVN_CAMCLK_SEL | S3C2440_CAMDIVN_CAMCLK_MASK); + + if (rate != parent_rate) { + camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; + camdivn |= (((parent_rate / rate) / 2) - 1); + } + + __raw_writel(camdivn, S3C2440_CAMDIVN); + + return 0; +} + +/* Extra S3C2440 clocks */ + +static struct clk s3c2440_clk_cam = { + .name = "camif", + .id = -1, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2440_CLKCON_CAMERA, +}; + +static struct clk s3c2440_clk_cam_upll = { + .name = "camif-upll", + .id = -1, + .set_rate = s3c2440_camif_upll_setrate, + .round_rate = s3c2440_camif_upll_round, +}; + +static struct clk s3c2440_clk_ac97 = { + .name = "ac97", + .id = -1, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2440_CLKCON_CAMERA, +}; + +static int s3c2440_clk_add(struct sys_device *sysdev) +{ + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); + unsigned long clkdivn; + struct clk *clock_h; + struct clk *clock_p; + struct clk *clock_upll; + + printk("S3C2440: Clock Support, DVS %s\n", + (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off"); + + clock_p = clk_get(NULL, "pclk"); + clock_h = clk_get(NULL, "hclk"); + clock_upll = clk_get(NULL, "upll"); + + if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) { + printk(KERN_ERR "S3C2440: Failed to get parent clocks\n"); + return -EINVAL; + } + + /* check rate of UPLL, and if it is near 96MHz, then change + * to using half the UPLL rate for the system */ + + if (clk_get_rate(clock_upll) > (94 * MHZ)) { + clk_usb_bus.rate = clk_get_rate(clock_upll) / 2; + + mutex_lock(&clocks_mutex); + + clkdivn = __raw_readl(S3C2410_CLKDIVN); + clkdivn |= S3C2440_CLKDIVN_UCLK; + __raw_writel(clkdivn, S3C2410_CLKDIVN); + + mutex_unlock(&clocks_mutex); + } + + s3c2440_clk_cam.parent = clock_h; + s3c2440_clk_ac97.parent = clock_p; + s3c2440_clk_cam_upll.parent = clock_upll; + + s3c24xx_register_clock(&s3c2440_clk_ac97); + s3c24xx_register_clock(&s3c2440_clk_cam); + s3c24xx_register_clock(&s3c2440_clk_cam_upll); + + clk_disable(&s3c2440_clk_ac97); + clk_disable(&s3c2440_clk_cam); + + return 0; +} + +static struct sysdev_driver s3c2440_clk_driver = { + .add = s3c2440_clk_add, +}; + +static __init int s3c24xx_clk_driver(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_clk_driver); +} + +arch_initcall(s3c24xx_clk_driver); diff --git a/arch/arm/mach-s3c2440/dma.c b/arch/arm/mach-s3c2440/dma.c new file mode 100644 index 000000000000..8e51137620f2 --- /dev/null +++ b/arch/arm/mach-s3c2440/dma.c @@ -0,0 +1,165 @@ +/* linux/arch/arm/mach-s3c2440/dma.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * S3C2440 DMA selection + * + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +static struct s3c24xx_dma_map __initdata s3c2440_dma_mappings[] = { + [DMACH_XD0] = { + .name = "xdreq0", + .channels[0] = S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID, + }, + [DMACH_XD1] = { + .name = "xdreq1", + .channels[1] = S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID, + }, + [DMACH_SDI] = { + .name = "sdi", + .channels[0] = S3C2410_DCON_CH0_SDI | DMA_CH_VALID, + .channels[1] = S3C2440_DCON_CH1_SDI | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_SDI | DMA_CH_VALID, + .channels[3] = S3C2410_DCON_CH3_SDI | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_SPI0] = { + .name = "spi0", + .channels[1] = S3C2410_DCON_CH1_SPI | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, + }, + [DMACH_SPI1] = { + .name = "spi1", + .channels[3] = S3C2410_DCON_CH3_SPI | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, + }, + [DMACH_UART0] = { + .name = "uart0", + .channels[0] = S3C2410_DCON_CH0_UART0 | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, + }, + [DMACH_UART1] = { + .name = "uart1", + .channels[1] = S3C2410_DCON_CH1_UART1 | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, + }, + [DMACH_UART2] = { + .name = "uart2", + .channels[3] = S3C2410_DCON_CH3_UART2 | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, + }, + [DMACH_TIMER] = { + .name = "timer", + .channels[0] = S3C2410_DCON_CH0_TIMER | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_TIMER | DMA_CH_VALID, + .channels[3] = S3C2410_DCON_CH3_TIMER | DMA_CH_VALID, + }, + [DMACH_I2S_IN] = { + .name = "i2s-sdi", + .channels[1] = S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID, + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_I2S_OUT] = { + .name = "i2s-sdo", + .channels[0] = S3C2440_DCON_CH0_I2SSDO | DMA_CH_VALID, + .channels[2] = S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID, + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_PCM_IN] = { + .name = "pcm-in", + .channels[0] = S3C2440_DCON_CH0_PCMIN | DMA_CH_VALID, + .channels[2] = S3C2440_DCON_CH2_PCMIN | DMA_CH_VALID, + .hw_addr.from = S3C2440_PA_AC97 + S3C_AC97_PCM_DATA, + }, + [DMACH_PCM_OUT] = { + .name = "pcm-out", + .channels[1] = S3C2440_DCON_CH1_PCMOUT | DMA_CH_VALID, + .channels[3] = S3C2440_DCON_CH3_PCMOUT | DMA_CH_VALID, + .hw_addr.to = S3C2440_PA_AC97 + S3C_AC97_PCM_DATA, + }, + [DMACH_MIC_IN] = { + .name = "mic-in", + .channels[2] = S3C2440_DCON_CH2_MICIN | DMA_CH_VALID, + .channels[3] = S3C2440_DCON_CH3_MICIN | DMA_CH_VALID, + .hw_addr.from = S3C2440_PA_AC97 + S3C_AC97_MIC_DATA, + }, + [DMACH_USB_EP1] = { + .name = "usb-ep1", + .channels[0] = S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID, + }, + [DMACH_USB_EP2] = { + .name = "usb-ep2", + .channels[1] = S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID, + }, + [DMACH_USB_EP3] = { + .name = "usb-ep3", + .channels[2] = S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID, + }, + [DMACH_USB_EP4] = { + .name = "usb-ep4", + .channels[3] = S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID, + }, +}; + +static void s3c2440_dma_select(struct s3c2410_dma_chan *chan, + struct s3c24xx_dma_map *map) +{ + chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID; +} + +static struct s3c24xx_dma_selection __initdata s3c2440_dma_sel = { + .select = s3c2440_dma_select, + .dcon_mask = 7 << 24, + .map = s3c2440_dma_mappings, + .map_size = ARRAY_SIZE(s3c2440_dma_mappings), +}; + +static int s3c2440_dma_add(struct sys_device *sysdev) +{ + return s3c24xx_dma_init_map(&s3c2440_dma_sel); +} + +static struct sysdev_driver s3c2440_dma_driver = { + .add = s3c2440_dma_add, +}; + +static int __init s3c2440_dma_init(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_dma_driver); +} + +arch_initcall(s3c2440_dma_init); + diff --git a/arch/arm/mach-s3c2440/dsc.c b/arch/arm/mach-s3c2440/dsc.c new file mode 100644 index 000000000000..2995ff5681bb --- /dev/null +++ b/arch/arm/mach-s3c2440/dsc.c @@ -0,0 +1,54 @@ +/* linux/arch/arm/mach-s3c2440/dsc.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Samsung S3C2440 Drive Strength Control support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include +#include + +int s3c2440_set_dsc(unsigned int pin, unsigned int value) +{ + void __iomem *base; + unsigned long val; + unsigned long flags; + unsigned long mask; + + base = (pin & S3C2440_SELECT_DSC1) ? S3C2440_DSC1 : S3C2440_DSC0; + mask = 3 << S3C2440_DSC_GETSHIFT(pin); + + local_irq_save(flags); + + val = __raw_readl(base); + val &= ~mask; + val |= value & mask; + __raw_writel(val, base); + + local_irq_restore(flags); + return 0; +} + +EXPORT_SYMBOL(s3c2440_set_dsc); diff --git a/arch/arm/mach-s3c2440/irq.c b/arch/arm/mach-s3c2440/irq.c new file mode 100644 index 000000000000..1069d13d8c57 --- /dev/null +++ b/arch/arm/mach-s3c2440/irq.c @@ -0,0 +1,130 @@ +/* linux/arch/arm/mach-s3c2440/irq.c + * + * Copyright (c) 2003,2004 Simtec Electronics + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * +*/ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include + +#include +#include +#include + +/* WDT/AC97 */ + +static void s3c_irq_demux_wdtac97(unsigned int irq, + struct irq_desc *desc) +{ + unsigned int subsrc, submsk; + struct irq_desc *mydesc; + + /* read the current pending interrupts, and the mask + * for what it is available */ + + subsrc = __raw_readl(S3C2410_SUBSRCPND); + submsk = __raw_readl(S3C2410_INTSUBMSK); + + subsrc &= ~submsk; + subsrc >>= 13; + subsrc &= 3; + + if (subsrc != 0) { + if (subsrc & 1) { + mydesc = irq_desc + IRQ_S3C2440_WDT; + desc_handle_irq(IRQ_S3C2440_WDT, mydesc); + } + if (subsrc & 2) { + mydesc = irq_desc + IRQ_S3C2440_AC97; + desc_handle_irq(IRQ_S3C2440_AC97, mydesc); + } + } +} + + +#define INTMSK_WDT (1UL << (IRQ_WDT - IRQ_EINT0)) + +static void +s3c_irq_wdtac97_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_WDT, 3<<13); +} + +static void +s3c_irq_wdtac97_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_WDT); +} + +static void +s3c_irq_wdtac97_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_WDT, 3<<13); +} + +static struct irq_chip s3c_irq_wdtac97 = { + .mask = s3c_irq_wdtac97_mask, + .unmask = s3c_irq_wdtac97_unmask, + .ack = s3c_irq_wdtac97_ack, +}; + +static int s3c2440_irq_add(struct sys_device *sysdev) +{ + unsigned int irqno; + + printk("S3C2440: IRQ Support\n"); + + /* add new chained handler for wdt, ac7 */ + + set_irq_chip(IRQ_WDT, &s3c_irq_level_chip); + set_irq_handler(IRQ_WDT, handle_level_irq); + set_irq_chained_handler(IRQ_WDT, s3c_irq_demux_wdtac97); + + for (irqno = IRQ_S3C2440_WDT; irqno <= IRQ_S3C2440_AC97; irqno++) { + set_irq_chip(irqno, &s3c_irq_wdtac97); + set_irq_handler(irqno, handle_level_irq); + set_irq_flags(irqno, IRQF_VALID); + } + + return 0; +} + +static struct sysdev_driver s3c2440_irq_driver = { + .add = s3c2440_irq_add, +}; + +static int s3c2440_irq_init(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver); +} + +arch_initcall(s3c2440_irq_init); + diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c new file mode 100644 index 000000000000..3f0288eb1ed5 --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-anubis.c @@ -0,0 +1,325 @@ +/* linux/arch/arm/mach-s3c2440/mach-anubis.c + * + * Copyright (c) 2003-2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#define COPYRIGHT ", (c) 2005 Simtec Electronics" + +static struct map_desc anubis_iodesc[] __initdata = { + /* ISA IO areas */ + + { + .virtual = (u32)S3C24XX_VA_ISA_BYTE, + .pfn = __phys_to_pfn(0x0), + .length = SZ_4M, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_WORD, + .pfn = __phys_to_pfn(0x0), + .length = SZ_4M, + .type = MT_DEVICE, + }, + + /* we could possibly compress the next set down into a set of smaller tables + * pagetables, but that would mean using an L2 section, and it still means + * we cannot actually feed the same register to an LDR due to 16K spacing + */ + + /* CPLD control registers */ + + { + .virtual = (u32)ANUBIS_VA_CTRL1, + .pfn = __phys_to_pfn(ANUBIS_PA_CTRL1), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = (u32)ANUBIS_VA_CTRL2, + .pfn = __phys_to_pfn(ANUBIS_PA_CTRL2), + .length = SZ_4K, + .type = MT_DEVICE, + }, +}; + +#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = { + [0] = { + .name = "uclk", + .divisor = 1, + .min_baud = 0, + .max_baud = 0, + }, + [1] = { + .name = "pclk", + .divisor = 1, + .min_baud = 0, + .max_baud = 0, + } +}; + + +static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = anubis_serial_clocks, + .clocks_size = ARRAY_SIZE(anubis_serial_clocks), + }, + [1] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = anubis_serial_clocks, + .clocks_size = ARRAY_SIZE(anubis_serial_clocks), + }, +}; + +/* NAND Flash on Anubis board */ + +static int external_map[] = { 2 }; +static int chip0_map[] = { 0 }; +static int chip1_map[] = { 1 }; + +static struct mtd_partition anubis_default_nand_part[] = { + [0] = { + .name = "Boot Agent", + .size = SZ_16K, + .offset = 0, + }, + [1] = { + .name = "/boot", + .size = SZ_4M - SZ_16K, + .offset = SZ_16K, + }, + [2] = { + .name = "user1", + .offset = SZ_4M, + .size = SZ_32M - SZ_4M, + }, + [3] = { + .name = "user2", + .offset = SZ_32M, + .size = MTDPART_SIZ_FULL, + } +}; + +/* the Anubis has 3 selectable slots for nand-flash, the two + * on-board chip areas, as well as the external slot. + * + * Note, there is no current hot-plug support for the External + * socket. +*/ + +static struct s3c2410_nand_set anubis_nand_sets[] = { + [1] = { + .name = "External", + .nr_chips = 1, + .nr_map = external_map, + .nr_partitions = ARRAY_SIZE(anubis_default_nand_part), + .partitions = anubis_default_nand_part, + }, + [0] = { + .name = "chip0", + .nr_chips = 1, + .nr_map = chip0_map, + .nr_partitions = ARRAY_SIZE(anubis_default_nand_part), + .partitions = anubis_default_nand_part, + }, + [2] = { + .name = "chip1", + .nr_chips = 1, + .nr_map = chip1_map, + .nr_partitions = ARRAY_SIZE(anubis_default_nand_part), + .partitions = anubis_default_nand_part, + }, +}; + +static void anubis_nand_select(struct s3c2410_nand_set *set, int slot) +{ + unsigned int tmp; + + slot = set->nr_map[slot] & 3; + + pr_debug("anubis_nand: selecting slot %d (set %p,%p)\n", + slot, set, set->nr_map); + + tmp = __raw_readb(ANUBIS_VA_CTRL1); + tmp &= ~ANUBIS_CTRL1_NANDSEL; + tmp |= slot; + + pr_debug("anubis_nand: ctrl1 now %02x\n", tmp); + + __raw_writeb(tmp, ANUBIS_VA_CTRL1); +} + +static struct s3c2410_platform_nand anubis_nand_info = { + .tacls = 25, + .twrph0 = 55, + .twrph1 = 40, + .nr_sets = ARRAY_SIZE(anubis_nand_sets), + .sets = anubis_nand_sets, + .select_chip = anubis_nand_select, +}; + +/* IDE channels */ + +static struct resource anubis_ide0_resource[] = { + { + .start = S3C2410_CS3, + .end = S3C2410_CS3 + (8*32) - 1, + .flags = IORESOURCE_MEM, + }, { + .start = S3C2410_CS3 + (1<<26), + .end = S3C2410_CS3 + (1<<26) + (8*32) - 1, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_IDE0, + .end = IRQ_IDE0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device anubis_device_ide0 = { + .name = "simtec-ide", + .id = 0, + .num_resources = ARRAY_SIZE(anubis_ide0_resource), + .resource = anubis_ide0_resource, +}; + +static struct resource anubis_ide1_resource[] = { + { + .start = S3C2410_CS4, + .end = S3C2410_CS4 + (8*32) - 1, + .flags = IORESOURCE_MEM, + }, { + .start = S3C2410_CS4 + (1<<26), + .end = S3C2410_CS4 + (1<<26) + (8*32) - 1, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_IDE0, + .end = IRQ_IDE0, + .flags = IORESOURCE_IRQ, + }, +}; + + +static struct platform_device anubis_device_ide1 = { + .name = "simtec-ide", + .id = 1, + .num_resources = ARRAY_SIZE(anubis_ide1_resource), + .resource = anubis_ide1_resource, +}; + +/* Standard Anubis devices */ + +static struct platform_device *anubis_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_wdt, + &s3c_device_adc, + &s3c_device_i2c, + &s3c_device_rtc, + &s3c_device_nand, + &anubis_device_ide0, + &anubis_device_ide1, +}; + +static struct clk *anubis_clocks[] = { + &s3c24xx_dclk0, + &s3c24xx_dclk1, + &s3c24xx_clkout0, + &s3c24xx_clkout1, + &s3c24xx_uclk, +}; + +static struct s3c24xx_board anubis_board __initdata = { + .devices = anubis_devices, + .devices_count = ARRAY_SIZE(anubis_devices), + .clocks = anubis_clocks, + .clocks_count = ARRAY_SIZE(anubis_clocks), +}; + +static void __init anubis_map_io(void) +{ + /* initialise the clocks */ + + s3c24xx_dclk0.parent = NULL; + s3c24xx_dclk0.rate = 12*1000*1000; + + s3c24xx_dclk1.parent = NULL; + s3c24xx_dclk1.rate = 24*1000*1000; + + s3c24xx_clkout0.parent = &s3c24xx_dclk0; + s3c24xx_clkout1.parent = &s3c24xx_dclk1; + + s3c24xx_uclk.parent = &s3c24xx_clkout1; + + s3c_device_nand.dev.platform_data = &anubis_nand_info; + + s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc)); + s3c24xx_init_clocks(0); + s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs)); + s3c24xx_set_board(&anubis_board); + + /* ensure that the GPIO is setup */ + s3c2410_gpio_setpin(S3C2410_GPA0, 1); +} + +MACHINE_START(ANUBIS, "Simtec-Anubis") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = anubis_map_io, + .init_irq = s3c24xx_init_irq, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c new file mode 100644 index 000000000000..6d551d88330b --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-nexcoder.c @@ -0,0 +1,158 @@ +/* linux/arch/arm/mach-s3c2440/mach-nexcoder.c + * + * Copyright (c) 2004 Nex Vision + * Guillaume GOURAT + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Modifications: + * 15-10-2004 GG Created initial version + * 12-03-2005 BJD Updated for release + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include +#include + +#include +#include +#include +#include +#include + +//#include +#include +#include + +#include +#include +#include +#include +#include + +static struct map_desc nexcoder_iodesc[] __initdata = { + /* nothing here yet */ +}; + +#define UCON S3C2410_UCON_DEFAULT +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg nexcoder_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + } +}; + +/* NOR Flash on NexVision NexCoder 2440 board */ + +static struct resource nexcoder_nor_resource[] = { + [0] = { + .start = S3C2410_CS0, + .end = S3C2410_CS0 + (8*1024*1024) - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct map_info nexcoder_nor_map = { + .bankwidth = 2, +}; + +static struct platform_device nexcoder_device_nor = { + .name = "mtd-flash", + .id = -1, + .num_resources = ARRAY_SIZE(nexcoder_nor_resource), + .resource = nexcoder_nor_resource, + .dev = + { + .platform_data = &nexcoder_nor_map, + } +}; + +/* Standard Nexcoder devices */ + +static struct platform_device *nexcoder_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_lcd, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, + &s3c_device_rtc, + &s3c_device_camif, + &s3c_device_spi0, + &s3c_device_spi1, + &nexcoder_device_nor, +}; + +static struct s3c24xx_board nexcoder_board __initdata = { + .devices = nexcoder_devices, + .devices_count = ARRAY_SIZE(nexcoder_devices), +}; + + +static void __init nexcoder_sensorboard_init(void) +{ + // Initialize SCCB bus + s3c2410_gpio_setpin(S3C2410_GPE14, 1); // IICSCL + s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_OUTP); + s3c2410_gpio_setpin(S3C2410_GPE15, 1); // IICSDA + s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_OUTP); + + // Power up the sensor board + s3c2410_gpio_setpin(S3C2410_GPF1, 1); + s3c2410_gpio_cfgpin(S3C2410_GPF1, S3C2410_GPF1_OUTP); // CAM_GPIO7 => nLDO_PWRDN + s3c2410_gpio_setpin(S3C2410_GPF2, 0); + s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP); // CAM_GPIO6 => CAM_PWRDN +} + +static void __init nexcoder_map_io(void) +{ + s3c24xx_init_io(nexcoder_iodesc, ARRAY_SIZE(nexcoder_iodesc)); + s3c24xx_init_clocks(0); + s3c24xx_init_uarts(nexcoder_uartcfgs, ARRAY_SIZE(nexcoder_uartcfgs)); + s3c24xx_set_board(&nexcoder_board); + nexcoder_sensorboard_init(); +} + + +MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440") + /* Maintainer: Guillaume GOURAT */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = nexcoder_map_io, + .init_irq = s3c24xx_init_irq, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c new file mode 100644 index 000000000000..2ed8e51f20c8 --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-osiris.c @@ -0,0 +1,303 @@ +/* linux/arch/arm/mach-s3c2440/mach-osiris.c + * + * Copyright (c) 2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +/* onboard perihpheral map */ + +static struct map_desc osiris_iodesc[] __initdata = { + /* ISA IO areas (may be over-written later) */ + + { + .virtual = (u32)S3C24XX_VA_ISA_BYTE, + .pfn = __phys_to_pfn(S3C2410_CS5), + .length = SZ_16M, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_WORD, + .pfn = __phys_to_pfn(S3C2410_CS5), + .length = SZ_16M, + .type = MT_DEVICE, + }, + + /* CPLD control registers */ + + { + .virtual = (u32)OSIRIS_VA_CTRL1, + .pfn = __phys_to_pfn(OSIRIS_PA_CTRL1), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = (u32)OSIRIS_VA_CTRL2, + .pfn = __phys_to_pfn(OSIRIS_PA_CTRL2), + .length = SZ_16K, + .type = MT_DEVICE, + }, +}; + +#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c24xx_uart_clksrc osiris_serial_clocks[] = { + [0] = { + .name = "uclk", + .divisor = 1, + .min_baud = 0, + .max_baud = 0, + }, + [1] = { + .name = "pclk", + .divisor = 1, + .min_baud = 0, + .max_baud = 0, + } +}; + +static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = osiris_serial_clocks, + .clocks_size = ARRAY_SIZE(osiris_serial_clocks), + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = osiris_serial_clocks, + .clocks_size = ARRAY_SIZE(osiris_serial_clocks), + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + .clocks = osiris_serial_clocks, + .clocks_size = ARRAY_SIZE(osiris_serial_clocks), + } +}; + +/* NAND Flash on Osiris board */ + +static int external_map[] = { 2 }; +static int chip0_map[] = { 0 }; +static int chip1_map[] = { 1 }; + +static struct mtd_partition osiris_default_nand_part[] = { + [0] = { + .name = "Boot Agent", + .size = SZ_16K, + .offset = 0, + }, + [1] = { + .name = "/boot", + .size = SZ_4M - SZ_16K, + .offset = SZ_16K, + }, + [2] = { + .name = "user1", + .offset = SZ_4M, + .size = SZ_32M - SZ_4M, + }, + [3] = { + .name = "user2", + .offset = SZ_32M, + .size = MTDPART_SIZ_FULL, + } +}; + +/* the Osiris has 3 selectable slots for nand-flash, the two + * on-board chip areas, as well as the external slot. + * + * Note, there is no current hot-plug support for the External + * socket. +*/ + +static struct s3c2410_nand_set osiris_nand_sets[] = { + [1] = { + .name = "External", + .nr_chips = 1, + .nr_map = external_map, + .nr_partitions = ARRAY_SIZE(osiris_default_nand_part), + .partitions = osiris_default_nand_part, + }, + [0] = { + .name = "chip0", + .nr_chips = 1, + .nr_map = chip0_map, + .nr_partitions = ARRAY_SIZE(osiris_default_nand_part), + .partitions = osiris_default_nand_part, + }, + [2] = { + .name = "chip1", + .nr_chips = 1, + .nr_map = chip1_map, + .nr_partitions = ARRAY_SIZE(osiris_default_nand_part), + .partitions = osiris_default_nand_part, + }, +}; + +static void osiris_nand_select(struct s3c2410_nand_set *set, int slot) +{ + unsigned int tmp; + + slot = set->nr_map[slot] & 3; + + pr_debug("osiris_nand: selecting slot %d (set %p,%p)\n", + slot, set, set->nr_map); + + tmp = __raw_readb(OSIRIS_VA_CTRL1); + tmp &= ~OSIRIS_CTRL1_NANDSEL; + tmp |= slot; + + pr_debug("osiris_nand: ctrl1 now %02x\n", tmp); + + __raw_writeb(tmp, OSIRIS_VA_CTRL1); +} + +static struct s3c2410_platform_nand osiris_nand_info = { + .tacls = 25, + .twrph0 = 60, + .twrph1 = 60, + .nr_sets = ARRAY_SIZE(osiris_nand_sets), + .sets = osiris_nand_sets, + .select_chip = osiris_nand_select, +}; + +/* PCMCIA control and configuration */ + +static struct resource osiris_pcmcia_resource[] = { + [0] = { + .start = 0x0f000000, + .end = 0x0f100000, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 0x0c000000, + .end = 0x0c100000, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device osiris_pcmcia = { + .name = "osiris-pcmcia", + .id = -1, + .num_resources = ARRAY_SIZE(osiris_pcmcia_resource), + .resource = osiris_pcmcia_resource, +}; + +/* Standard Osiris devices */ + +static struct platform_device *osiris_devices[] __initdata = { + &s3c_device_i2c, + &s3c_device_nand, + &osiris_pcmcia, +}; + +static struct clk *osiris_clocks[] = { + &s3c24xx_dclk0, + &s3c24xx_dclk1, + &s3c24xx_clkout0, + &s3c24xx_clkout1, + &s3c24xx_uclk, +}; + +static struct s3c24xx_board osiris_board __initdata = { + .devices = osiris_devices, + .devices_count = ARRAY_SIZE(osiris_devices), + .clocks = osiris_clocks, + .clocks_count = ARRAY_SIZE(osiris_clocks), +}; + +static void __init osiris_map_io(void) +{ + unsigned long flags; + + /* initialise the clocks */ + + s3c24xx_dclk0.parent = NULL; + s3c24xx_dclk0.rate = 12*1000*1000; + + s3c24xx_dclk1.parent = NULL; + s3c24xx_dclk1.rate = 24*1000*1000; + + s3c24xx_clkout0.parent = &s3c24xx_dclk0; + s3c24xx_clkout1.parent = &s3c24xx_dclk1; + + s3c24xx_uclk.parent = &s3c24xx_clkout1; + + s3c_device_nand.dev.platform_data = &osiris_nand_info; + + s3c24xx_init_io(osiris_iodesc, ARRAY_SIZE(osiris_iodesc)); + s3c24xx_init_clocks(0); + s3c24xx_init_uarts(osiris_uartcfgs, ARRAY_SIZE(osiris_uartcfgs)); + s3c24xx_set_board(&osiris_board); + + /* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */ + + local_irq_save(flags); + __raw_writel(__raw_readl(S3C2410_BWSCON) | S3C2410_BWSCON_ST1 | S3C2410_BWSCON_ST2 | S3C2410_BWSCON_ST3 | S3C2410_BWSCON_ST4 | S3C2410_BWSCON_ST5, S3C2410_BWSCON); + local_irq_restore(flags); + + /* write-protect line to the NAND */ + s3c2410_gpio_setpin(S3C2410_GPA0, 1); +} + +MACHINE_START(OSIRIS, "Simtec-OSIRIS") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = osiris_map_io, + .init_irq = s3c24xx_init_irq, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/mach-rx3715.c b/arch/arm/mach-s3c2440/mach-rx3715.c new file mode 100644 index 000000000000..1d4e19bd9206 --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-rx3715.c @@ -0,0 +1,244 @@ +/* linux/arch/arm/mach-s3c2440/mach-rx3715.c + * + * Copyright (c) 2003,2004 Simtec Electronics + * Ben Dooks + * + * http://www.handhelds.org/projects/rx3715.html + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include + +static struct map_desc rx3715_iodesc[] __initdata = { + /* dump ISA space somewhere unused */ + + { + .virtual = (u32)S3C24XX_VA_ISA_WORD, + .pfn = __phys_to_pfn(S3C2410_CS3), + .length = SZ_1M, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_BYTE, + .pfn = __phys_to_pfn(S3C2410_CS3), + .length = SZ_1M, + .type = MT_DEVICE, + }, +}; + + +static struct s3c24xx_uart_clksrc rx3715_serial_clocks[] = { + [0] = { + .name = "fclk", + .divisor = 0, + .min_baud = 0, + .max_baud = 0, + } +}; + +static struct s3c2410_uartcfg rx3715_uartcfgs[] = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + .clocks = rx3715_serial_clocks, + .clocks_size = ARRAY_SIZE(rx3715_serial_clocks), + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x00, + .clocks = rx3715_serial_clocks, + .clocks_size = ARRAY_SIZE(rx3715_serial_clocks), + }, + /* IR port */ + [2] = { + .hwport = 2, + .uart_flags = UPF_CONS_FLOW, + .ucon = 0x3c5, + .ulcon = 0x43, + .ufcon = 0x51, + .clocks = rx3715_serial_clocks, + .clocks_size = ARRAY_SIZE(rx3715_serial_clocks), + } +}; + +/* framebuffer lcd controller information */ + +static struct s3c2410fb_mach_info rx3715_lcdcfg __initdata = { + .regs = { + .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | \ + S3C2410_LCDCON1_TFT | \ + S3C2410_LCDCON1_CLKVAL(0x0C), + + .lcdcon2 = S3C2410_LCDCON2_VBPD(5) | \ + S3C2410_LCDCON2_LINEVAL(319) | \ + S3C2410_LCDCON2_VFPD(6) | \ + S3C2410_LCDCON2_VSPW(2), + + .lcdcon3 = S3C2410_LCDCON3_HBPD(35) | \ + S3C2410_LCDCON3_HOZVAL(239) | \ + S3C2410_LCDCON3_HFPD(35), + + .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | \ + S3C2410_LCDCON4_HSPW(7), + + .lcdcon5 = S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_HWSWP, + }, + + .lpcsel = 0xf82, + + .gpccon = 0xaa955699, + .gpccon_mask = 0xffc003cc, + .gpcup = 0x0000ffff, + .gpcup_mask = 0xffffffff, + + .gpdcon = 0xaa95aaa1, + .gpdcon_mask = 0xffc0fff0, + .gpdup = 0x0000faff, + .gpdup_mask = 0xffffffff, + + .fixed_syncs = 1, + .width = 240, + .height = 320, + + .xres = { + .min = 240, + .max = 240, + .defval = 240, + }, + + .yres = { + .max = 320, + .min = 320, + .defval = 320, + }, + + .bpp = { + .min = 16, + .max = 16, + .defval = 16, + }, +}; + +static struct mtd_partition rx3715_nand_part[] = { + [0] = { + .name = "Whole Flash", + .offset = 0, + .size = MTDPART_SIZ_FULL, + .mask_flags = MTD_WRITEABLE, + } +}; + +static struct s3c2410_nand_set rx3715_nand_sets[] = { + [0] = { + .name = "Internal", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(rx3715_nand_part), + .partitions = rx3715_nand_part, + }, +}; + +static struct s3c2410_platform_nand rx3715_nand_info = { + .tacls = 25, + .twrph0 = 50, + .twrph1 = 15, + .nr_sets = ARRAY_SIZE(rx3715_nand_sets), + .sets = rx3715_nand_sets, +}; + +static struct platform_device *rx3715_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_lcd, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, + &s3c_device_nand, +}; + +static struct s3c24xx_board rx3715_board __initdata = { + .devices = rx3715_devices, + .devices_count = ARRAY_SIZE(rx3715_devices) +}; + +static void __init rx3715_map_io(void) +{ + s3c_device_nand.dev.platform_data = &rx3715_nand_info; + + s3c24xx_init_io(rx3715_iodesc, ARRAY_SIZE(rx3715_iodesc)); + s3c24xx_init_clocks(16934000); + s3c24xx_init_uarts(rx3715_uartcfgs, ARRAY_SIZE(rx3715_uartcfgs)); + s3c24xx_set_board(&rx3715_board); +} + +static void __init rx3715_init_irq(void) +{ + s3c24xx_init_irq(); +} + +static void __init rx3715_init_machine(void) +{ + memcpy(phys_to_virt(H1940_SUSPEND_RESUMEAT), h1940_pm_return, 1024); + s3c2410_pm_init(); + + s3c24xx_fb_set_platdata(&rx3715_lcdcfg); +} + + +MACHINE_START(RX3715, "IPAQ-RX3715") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = rx3715_map_io, + .init_irq = rx3715_init_irq, + .init_machine = rx3715_init_machine, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/mach-smdk2440.c b/arch/arm/mach-s3c2440/mach-smdk2440.c new file mode 100644 index 000000000000..270e42b9b5c1 --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-smdk2440.c @@ -0,0 +1,208 @@ +/* linux/arch/arm/mach-s3c2440/mach-smdk2440.c + * + * Copyright (c) 2004,2005 Simtec Electronics + * Ben Dooks + * + * http://www.fluff.org/ben/smdk2440/ + * + * Thanks to Dimity Andric and TomTom for the loan of an SMDK2440. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include + +//#include +#include +#include +#include + +#include +#include + +#include +#include +#include +#include +#include + +#include + +static struct map_desc smdk2440_iodesc[] __initdata = { + /* ISA IO Space map (memory space selected by A24) */ + + { + .virtual = (u32)S3C24XX_VA_ISA_WORD, + .pfn = __phys_to_pfn(S3C2410_CS2), + .length = 0x10000, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_WORD + 0x10000, + .pfn = __phys_to_pfn(S3C2410_CS2 + (1<<24)), + .length = SZ_4M, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_BYTE, + .pfn = __phys_to_pfn(S3C2410_CS2), + .length = 0x10000, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_BYTE + 0x10000, + .pfn = __phys_to_pfn(S3C2410_CS2 + (1<<24)), + .length = SZ_4M, + .type = MT_DEVICE, + } +}; + +#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg smdk2440_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + /* IR port */ + [2] = { + .hwport = 2, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x43, + .ufcon = 0x51, + } +}; + +/* LCD driver info */ + +static struct s3c2410fb_mach_info smdk2440_lcd_cfg __initdata = { + .regs = { + + .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | + S3C2410_LCDCON1_TFT | + S3C2410_LCDCON1_CLKVAL(0x04), + + .lcdcon2 = S3C2410_LCDCON2_VBPD(7) | + S3C2410_LCDCON2_LINEVAL(319) | + S3C2410_LCDCON2_VFPD(6) | + S3C2410_LCDCON2_VSPW(3), + + .lcdcon3 = S3C2410_LCDCON3_HBPD(19) | + S3C2410_LCDCON3_HOZVAL(239) | + S3C2410_LCDCON3_HFPD(7), + + .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | + S3C2410_LCDCON4_HSPW(3), + + .lcdcon5 = S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_PWREN | + S3C2410_LCDCON5_HWSWP, + }, + +#if 0 + /* currently setup by downloader */ + .gpccon = 0xaa940659, + .gpccon_mask = 0xffffffff, + .gpcup = 0x0000ffff, + .gpcup_mask = 0xffffffff, + .gpdcon = 0xaa84aaa0, + .gpdcon_mask = 0xffffffff, + .gpdup = 0x0000faff, + .gpdup_mask = 0xffffffff, +#endif + + .lpcsel = ((0xCE6) & ~7) | 1<<4, + + .width = 240, + .height = 320, + + .xres = { + .min = 240, + .max = 240, + .defval = 240, + }, + + .yres = { + .min = 320, + .max = 320, + .defval = 320, + }, + + .bpp = { + .min = 16, + .max = 16, + .defval = 16, + }, +}; + +static struct platform_device *smdk2440_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_lcd, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, +}; + +static struct s3c24xx_board smdk2440_board __initdata = { + .devices = smdk2440_devices, + .devices_count = ARRAY_SIZE(smdk2440_devices) +}; + +static void __init smdk2440_map_io(void) +{ + s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc)); + s3c24xx_init_clocks(16934400); + s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs)); + s3c24xx_set_board(&smdk2440_board); +} + +static void __init smdk2440_machine_init(void) +{ + s3c24xx_fb_set_platdata(&smdk2440_lcd_cfg); + + smdk_machine_init(); +} + +MACHINE_START(S3C2440, "SMDK2440") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .init_irq = s3c24xx_init_irq, + .map_io = smdk2440_map_io, + .init_machine = smdk2440_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2440/s3c2440.c b/arch/arm/mach-s3c2440/s3c2440.c new file mode 100644 index 000000000000..90e1da61fbc3 --- /dev/null +++ b/arch/arm/mach-s3c2440/s3c2440.c @@ -0,0 +1,52 @@ +/* linux/arch/arm/mach-s3c2440/s3c2440.c + * + * Copyright (c) 2004-2006 Simtec Electronics + * Ben Dooks + * + * Samsung S3C2440 Mobile CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +static struct sys_device s3c2440_sysdev = { + .cls = &s3c2440_sysclass, +}; + +int __init s3c2440_init(void) +{ + printk("S3C2440: Initialising architecture\n"); + + /* change irq for watchdog */ + + s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT; + s3c_device_wdt.resource[1].end = IRQ_S3C2440_WDT; + + /* register our system device for everything else */ + + return sysdev_register(&s3c2440_sysdev); +} diff --git a/arch/arm/mach-s3c2442/Kconfig b/arch/arm/mach-s3c2442/Kconfig new file mode 100644 index 000000000000..bf8d87abfab3 --- /dev/null +++ b/arch/arm/mach-s3c2442/Kconfig @@ -0,0 +1,27 @@ +# arch/arm/mach-s3c2442/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +config CPU_S3C2442 + bool + depends on ARCH_S3C2420 + select S3C2410_CLOCK + select S3C2410_GPIO + select S3C2410_PM if PM + select CPU_S3C244X + help + Support for S3C2442 Samsung Mobile CPU based systems. + + +menu "S3C2442 Machines" + +config SMDK2440_CPU2442 + bool "SMDM2440 with S3C2442 CPU module" + depends on ARCH_S3C2440 + select CPU_S3C2442 + + +endmenu + diff --git a/arch/arm/mach-s3c2442/Makefile b/arch/arm/mach-s3c2442/Makefile new file mode 100644 index 000000000000..2a909c6c5798 --- /dev/null +++ b/arch/arm/mach-s3c2442/Makefile @@ -0,0 +1,16 @@ +# arch/arm/mach-s3c2442/Makefile +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +obj-y := +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_CPU_S3C2442) += s3c2442.o +obj-$(CONFIG_CPU_S3C2442) += clock.o + +# Machine support + diff --git a/arch/arm/mach-s3c2442/clock.c b/arch/arm/mach-s3c2442/clock.c new file mode 100644 index 000000000000..5b9e830ac4d3 --- /dev/null +++ b/arch/arm/mach-s3c2442/clock.c @@ -0,0 +1,171 @@ +/* linux/arch/arm/mach-s3c2442/clock.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C2442 Clock support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include + +#include +#include + +/* S3C2442 extended clock support */ + +static unsigned long s3c2442_camif_upll_round(struct clk *clk, + unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + int div; + + if (rate > parent_rate) + return parent_rate; + + div = parent_rate / rate; + + if (div == 3) + return parent_rate / 3; + + /* note, we remove the +/- 1 calculations for the divisor */ + + div /= 2; + + if (div < 1) + div = 1; + else if (div > 16) + div = 16; + + return parent_rate / (div * 2); +} + +static int s3c2442_camif_upll_setrate(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); + + rate = s3c2442_camif_upll_round(clk, rate); + + camdivn &= ~S3C2442_CAMDIVN_CAMCLK_DIV3; + + if (rate == parent_rate) { + camdivn &= ~S3C2440_CAMDIVN_CAMCLK_SEL; + } else if ((parent_rate / rate) == 3) { + camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; + camdivn |= S3C2442_CAMDIVN_CAMCLK_DIV3; + } else { + camdivn &= ~S3C2440_CAMDIVN_CAMCLK_MASK; + camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; + camdivn |= (((parent_rate / rate) / 2) - 1); + } + + __raw_writel(camdivn, S3C2440_CAMDIVN); + + return 0; +} + +/* Extra S3C2442 clocks */ + +static struct clk s3c2442_clk_cam = { + .name = "camif", + .id = -1, + .enable = s3c2410_clkcon_enable, + .ctrlbit = S3C2440_CLKCON_CAMERA, +}; + +static struct clk s3c2442_clk_cam_upll = { + .name = "camif-upll", + .id = -1, + .set_rate = s3c2442_camif_upll_setrate, + .round_rate = s3c2442_camif_upll_round, +}; + +static int s3c2442_clk_add(struct sys_device *sysdev) +{ + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); + unsigned long clkdivn; + struct clk *clock_h; + struct clk *clock_p; + struct clk *clock_upll; + + printk("S3C2442: Clock Support, DVS %s\n", + (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off"); + + clock_p = clk_get(NULL, "pclk"); + clock_h = clk_get(NULL, "hclk"); + clock_upll = clk_get(NULL, "upll"); + + if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) { + printk(KERN_ERR "S3C2442: Failed to get parent clocks\n"); + return -EINVAL; + } + + /* check rate of UPLL, and if it is near 96MHz, then change + * to using half the UPLL rate for the system */ + + if (clk_get_rate(clock_upll) > (94 * MHZ)) { + clk_usb_bus.rate = clk_get_rate(clock_upll) / 2; + + mutex_lock(&clocks_mutex); + + clkdivn = __raw_readl(S3C2410_CLKDIVN); + clkdivn |= S3C2440_CLKDIVN_UCLK; + __raw_writel(clkdivn, S3C2410_CLKDIVN); + + mutex_unlock(&clocks_mutex); + } + + s3c2442_clk_cam.parent = clock_h; + s3c2442_clk_cam_upll.parent = clock_upll; + + s3c24xx_register_clock(&s3c2442_clk_cam); + s3c24xx_register_clock(&s3c2442_clk_cam_upll); + + clk_disable(&s3c2442_clk_cam); + + return 0; +} + +static struct sysdev_driver s3c2442_clk_driver = { + .add = s3c2442_clk_add, +}; + +static __init int s3c2442_clk_init(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_clk_driver); +} + +arch_initcall(s3c2442_clk_init); diff --git a/arch/arm/mach-s3c2442/s3c2442.c b/arch/arm/mach-s3c2442/s3c2442.c new file mode 100644 index 000000000000..fbf8264249da --- /dev/null +++ b/arch/arm/mach-s3c2442/s3c2442.c @@ -0,0 +1,34 @@ +/* linux/arch/arm/mach-s3c2442/s3c2442.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * Samsung S3C2442 Mobile CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +static struct sys_device s3c2442_sysdev = { + .cls = &s3c2442_sysclass, +}; + +int __init s3c2442_init(void) +{ + printk("S3C2442: Initialising architecture\n"); + + return sysdev_register(&s3c2442_sysdev); +} diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig new file mode 100644 index 000000000000..97813645b5ee --- /dev/null +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -0,0 +1,96 @@ +# arch/arm/plat-s3c24xx/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +config PLAT_S3C24XX + bool + depends on ARCH_S3C2410 + default y + help + Base platform code for any Samsung S3C device + +config CPU_S3C244X + bool + depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442) + help + Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems. + +config PM_SIMTEC + bool + help + Common power management code for systems that are + compatible with the Simtec style of power management + +config S3C2410_BOOT_WATCHDOG + bool "S3C2410 Initialisation watchdog" + depends on ARCH_S3C2410 && S3C2410_WATCHDOG + help + Say y to enable the watchdog during the kernel decompression + stage. If the kernel fails to uncompress, then the watchdog + will trigger a reset and the system should restart. + +config S3C2410_BOOT_ERROR_RESET + bool "S3C2410 Reboot on decompression error" + depends on ARCH_S3C2410 + help + Say y here to use the watchdog to reset the system if the + kernel decompressor detects an error during decompression. + +config S3C2410_PM_DEBUG + bool "S3C2410 PM Suspend debug" + depends on ARCH_S3C2410 && PM + help + Say Y here if you want verbose debugging from the PM Suspend and + Resume code. See + for more information. + +config S3C2410_PM_CHECK + bool "S3C2410 PM Suspend Memory CRC" + depends on ARCH_S3C2410 && PM && CRC32 + help + Enable the PM code's memory area checksum over sleep. This option + will generate CRCs of all blocks of memory, and store them before + going to sleep. The blocks are then checked on resume for any + errors. + +config S3C2410_PM_CHECK_CHUNKSIZE + int "S3C2410 PM Suspend CRC Chunksize (KiB)" + depends on ARCH_S3C2410 && PM && S3C2410_PM_CHECK + default 64 + help + Set the chunksize in Kilobytes of the CRC for checking memory + corruption over suspend and resume. A smaller value will mean that + the CRC data block will take more memory, but wil identify any + faults with better precision. + +config S3C2410_LOWLEVEL_UART_PORT + int "S3C2410 UART to use for low-level messages" + default 0 + help + Choice of which UART port to use for the low-level messages, + such as the `Uncompressing...` at start time. The value of + this configuration should be between zero and two. The port + must have been initialised by the boot-loader before use. + +config S3C2410_DMA + bool "S3C2410 DMA support" + depends on ARCH_S3C2410 + help + S3C2410 DMA support. This is needed for drivers like sound which + use the S3C2410's DMA system to move data to and from the + peripheral blocks. + +config S3C2410_DMA_DEBUG + bool "S3C2410 DMA support debug" + depends on ARCH_S3C2410 && S3C2410_DMA + help + Enable debugging output for the DMA code. This option sends info + to the kernel log, at priority KERN_DEBUG. + +config MACH_SMDK + bool + help + Common machine code for SMDK2410 and SMDK2440 + diff --git a/arch/arm/plat-s3c24xx/Makefile b/arch/arm/plat-s3c24xx/Makefile new file mode 100644 index 000000000000..8e5ccaa1f03c --- /dev/null +++ b/arch/arm/plat-s3c24xx/Makefile @@ -0,0 +1,30 @@ +# arch/arm/plat-s3c24xx/Makefile +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +obj-y := +obj-m := +obj-n := +obj- := + + +# Core files + +obj-y += cpu.o +obj-y += irq.o +obj-y += devs.o +obj-y += gpio.o +obj-y += time.o +obj-y += clock.o + +# Architecture dependant builds + +obj-$(CONFIG_CPU_S3C244X) += s3c244x.o +obj-$(CONFIG_CPU_S3C244X) += s3c244x-irq.o +obj-$(CONFIG_PM_SIMTEC) += pm-simtec.o +obj-$(CONFIG_PM) += pm.o +obj-$(CONFIG_PM) += sleep.o +obj-$(CONFIG_S3C2410_DMA) += dma.o +obj-$(CONFIG_MACH_SMDK) += common-smdk.o diff --git a/arch/arm/plat-s3c24xx/clock.c b/arch/arm/plat-s3c24xx/clock.c new file mode 100644 index 000000000000..d3dc03a7383a --- /dev/null +++ b/arch/arm/plat-s3c24xx/clock.c @@ -0,0 +1,449 @@ +/* linux/arch/arm/plat-s3c24xx/clock.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * S3C24XX Core clock control support + * + * Based on, and code from linux/arch/arm/mach-versatile/clock.c + ** + ** Copyright (C) 2004 ARM Limited. + ** Written by Deep Blue Solutions Limited. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include +#include + +/* clock information */ + +static LIST_HEAD(clocks); + +DEFINE_MUTEX(clocks_mutex); + +/* enable and disable calls for use with the clk struct */ + +static int clk_null_enable(struct clk *clk, int enable) +{ + return 0; +} + +/* Clock API calls */ + +struct clk *clk_get(struct device *dev, const char *id) +{ + struct clk *p; + struct clk *clk = ERR_PTR(-ENOENT); + int idno; + + if (dev == NULL || dev->bus != &platform_bus_type) + idno = -1; + else + idno = to_platform_device(dev)->id; + + mutex_lock(&clocks_mutex); + + list_for_each_entry(p, &clocks, list) { + if (p->id == idno && + strcmp(id, p->name) == 0 && + try_module_get(p->owner)) { + clk = p; + break; + } + } + + /* check for the case where a device was supplied, but the + * clock that was being searched for is not device specific */ + + if (IS_ERR(clk)) { + list_for_each_entry(p, &clocks, list) { + if (p->id == -1 && strcmp(id, p->name) == 0 && + try_module_get(p->owner)) { + clk = p; + break; + } + } + } + + mutex_unlock(&clocks_mutex); + return clk; +} + +void clk_put(struct clk *clk) +{ + module_put(clk->owner); +} + +int clk_enable(struct clk *clk) +{ + if (IS_ERR(clk) || clk == NULL) + return -EINVAL; + + clk_enable(clk->parent); + + mutex_lock(&clocks_mutex); + + if ((clk->usage++) == 0) + (clk->enable)(clk, 1); + + mutex_unlock(&clocks_mutex); + return 0; +} + +void clk_disable(struct clk *clk) +{ + if (IS_ERR(clk) || clk == NULL) + return; + + mutex_lock(&clocks_mutex); + + if ((--clk->usage) == 0) + (clk->enable)(clk, 0); + + mutex_unlock(&clocks_mutex); + clk_disable(clk->parent); +} + + +unsigned long clk_get_rate(struct clk *clk) +{ + if (IS_ERR(clk)) + return 0; + + if (clk->rate != 0) + return clk->rate; + + if (clk->get_rate != NULL) + return (clk->get_rate)(clk); + + if (clk->parent != NULL) + return clk_get_rate(clk->parent); + + return clk->rate; +} + +long clk_round_rate(struct clk *clk, unsigned long rate) +{ + if (!IS_ERR(clk) && clk->round_rate) + return (clk->round_rate)(clk, rate); + + return rate; +} + +int clk_set_rate(struct clk *clk, unsigned long rate) +{ + int ret; + + if (IS_ERR(clk)) + return -EINVAL; + + mutex_lock(&clocks_mutex); + ret = (clk->set_rate)(clk, rate); + mutex_unlock(&clocks_mutex); + + return ret; +} + +struct clk *clk_get_parent(struct clk *clk) +{ + return clk->parent; +} + +int clk_set_parent(struct clk *clk, struct clk *parent) +{ + int ret = 0; + + if (IS_ERR(clk)) + return -EINVAL; + + mutex_lock(&clocks_mutex); + + if (clk->set_parent) + ret = (clk->set_parent)(clk, parent); + + mutex_unlock(&clocks_mutex); + + return ret; +} + +EXPORT_SYMBOL(clk_get); +EXPORT_SYMBOL(clk_put); +EXPORT_SYMBOL(clk_enable); +EXPORT_SYMBOL(clk_disable); +EXPORT_SYMBOL(clk_get_rate); +EXPORT_SYMBOL(clk_round_rate); +EXPORT_SYMBOL(clk_set_rate); +EXPORT_SYMBOL(clk_get_parent); +EXPORT_SYMBOL(clk_set_parent); + +/* base clocks */ + +struct clk clk_xtal = { + .name = "xtal", + .id = -1, + .rate = 0, + .parent = NULL, + .ctrlbit = 0, +}; + +struct clk clk_mpll = { + .name = "mpll", + .id = -1, +}; + +struct clk clk_upll = { + .name = "upll", + .id = -1, + .parent = NULL, + .ctrlbit = 0, +}; + +struct clk clk_f = { + .name = "fclk", + .id = -1, + .rate = 0, + .parent = &clk_mpll, + .ctrlbit = 0, +}; + +struct clk clk_h = { + .name = "hclk", + .id = -1, + .rate = 0, + .parent = NULL, + .ctrlbit = 0, +}; + +struct clk clk_p = { + .name = "pclk", + .id = -1, + .rate = 0, + .parent = NULL, + .ctrlbit = 0, +}; + +struct clk clk_usb_bus = { + .name = "usb-bus", + .id = -1, + .rate = 0, + .parent = &clk_upll, +}; + +/* clocks that could be registered by external code */ + +static int s3c24xx_dclk_enable(struct clk *clk, int enable) +{ + unsigned long dclkcon = __raw_readl(S3C24XX_DCLKCON); + + if (enable) + dclkcon |= clk->ctrlbit; + else + dclkcon &= ~clk->ctrlbit; + + __raw_writel(dclkcon, S3C24XX_DCLKCON); + + return 0; +} + +static int s3c24xx_dclk_setparent(struct clk *clk, struct clk *parent) +{ + unsigned long dclkcon; + unsigned int uclk; + + if (parent == &clk_upll) + uclk = 1; + else if (parent == &clk_p) + uclk = 0; + else + return -EINVAL; + + clk->parent = parent; + + dclkcon = __raw_readl(S3C24XX_DCLKCON); + + if (clk->ctrlbit == S3C2410_DCLKCON_DCLK0EN) { + if (uclk) + dclkcon |= S3C2410_DCLKCON_DCLK0_UCLK; + else + dclkcon &= ~S3C2410_DCLKCON_DCLK0_UCLK; + } else { + if (uclk) + dclkcon |= S3C2410_DCLKCON_DCLK1_UCLK; + else + dclkcon &= ~S3C2410_DCLKCON_DCLK1_UCLK; + } + + __raw_writel(dclkcon, S3C24XX_DCLKCON); + + return 0; +} + + +static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent) +{ + unsigned long mask; + unsigned long source; + + /* calculate the MISCCR setting for the clock */ + + if (parent == &clk_xtal) + source = S3C2410_MISCCR_CLK0_MPLL; + else if (parent == &clk_upll) + source = S3C2410_MISCCR_CLK0_UPLL; + else if (parent == &clk_f) + source = S3C2410_MISCCR_CLK0_FCLK; + else if (parent == &clk_h) + source = S3C2410_MISCCR_CLK0_HCLK; + else if (parent == &clk_p) + source = S3C2410_MISCCR_CLK0_PCLK; + else if (clk == &s3c24xx_clkout0 && parent == &s3c24xx_dclk0) + source = S3C2410_MISCCR_CLK0_DCLK0; + else if (clk == &s3c24xx_clkout1 && parent == &s3c24xx_dclk1) + source = S3C2410_MISCCR_CLK0_DCLK0; + else + return -EINVAL; + + clk->parent = parent; + + if (clk == &s3c24xx_dclk0) + mask = S3C2410_MISCCR_CLK0_MASK; + else { + source <<= 4; + mask = S3C2410_MISCCR_CLK1_MASK; + } + + s3c2410_modify_misccr(mask, source); + return 0; +} + +/* external clock definitions */ + +struct clk s3c24xx_dclk0 = { + .name = "dclk0", + .id = -1, + .ctrlbit = S3C2410_DCLKCON_DCLK0EN, + .enable = s3c24xx_dclk_enable, + .set_parent = s3c24xx_dclk_setparent, +}; + +struct clk s3c24xx_dclk1 = { + .name = "dclk1", + .id = -1, + .ctrlbit = S3C2410_DCLKCON_DCLK0EN, + .enable = s3c24xx_dclk_enable, + .set_parent = s3c24xx_dclk_setparent, +}; + +struct clk s3c24xx_clkout0 = { + .name = "clkout0", + .id = -1, + .set_parent = s3c24xx_clkout_setparent, +}; + +struct clk s3c24xx_clkout1 = { + .name = "clkout1", + .id = -1, + .set_parent = s3c24xx_clkout_setparent, +}; + +struct clk s3c24xx_uclk = { + .name = "uclk", + .id = -1, +}; + +/* initialise the clock system */ + +int s3c24xx_register_clock(struct clk *clk) +{ + clk->owner = THIS_MODULE; + + if (clk->enable == NULL) + clk->enable = clk_null_enable; + + /* add to the list of available clocks */ + + mutex_lock(&clocks_mutex); + list_add(&clk->list, &clocks); + mutex_unlock(&clocks_mutex); + + return 0; +} + +/* initalise all the clocks */ + +int __init s3c24xx_setup_clocks(unsigned long xtal, + unsigned long fclk, + unsigned long hclk, + unsigned long pclk) +{ + printk(KERN_INFO "S3C24XX Clocks, (c) 2004 Simtec Electronics\n"); + + /* initialise the main system clocks */ + + clk_xtal.rate = xtal; + clk_upll.rate = s3c2410_get_pll(__raw_readl(S3C2410_UPLLCON), xtal); + + clk_mpll.rate = fclk; + clk_h.rate = hclk; + clk_p.rate = pclk; + clk_f.rate = fclk; + + /* assume uart clocks are correctly setup */ + + /* register our clocks */ + + if (s3c24xx_register_clock(&clk_xtal) < 0) + printk(KERN_ERR "failed to register master xtal\n"); + + if (s3c24xx_register_clock(&clk_mpll) < 0) + printk(KERN_ERR "failed to register mpll clock\n"); + + if (s3c24xx_register_clock(&clk_upll) < 0) + printk(KERN_ERR "failed to register upll clock\n"); + + if (s3c24xx_register_clock(&clk_f) < 0) + printk(KERN_ERR "failed to register cpu fclk\n"); + + if (s3c24xx_register_clock(&clk_h) < 0) + printk(KERN_ERR "failed to register cpu hclk\n"); + + if (s3c24xx_register_clock(&clk_p) < 0) + printk(KERN_ERR "failed to register cpu pclk\n"); + + return 0; +} diff --git a/arch/arm/plat-s3c24xx/common-smdk.c b/arch/arm/plat-s3c24xx/common-smdk.c new file mode 100644 index 000000000000..908efa7d745f --- /dev/null +++ b/arch/arm/plat-s3c24xx/common-smdk.c @@ -0,0 +1,200 @@ +/* linux/arch/arm/plat-s3c24xx/common-smdk.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * Common code for SMDK2410 and SMDK2440 boards + * + * http://www.fluff.org/ben/smdk2440/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include + +#include +#include +#include + +/* LED devices */ + +static struct s3c24xx_led_platdata smdk_pdata_led4 = { + .gpio = S3C2410_GPF4, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led4", + .def_trigger = "timer", +}; + +static struct s3c24xx_led_platdata smdk_pdata_led5 = { + .gpio = S3C2410_GPF5, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led5", + .def_trigger = "nand-disk", +}; + +static struct s3c24xx_led_platdata smdk_pdata_led6 = { + .gpio = S3C2410_GPF6, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led6", +}; + +static struct s3c24xx_led_platdata smdk_pdata_led7 = { + .gpio = S3C2410_GPF7, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led7", +}; + +static struct platform_device smdk_led4 = { + .name = "s3c24xx_led", + .id = 0, + .dev = { + .platform_data = &smdk_pdata_led4, + }, +}; + +static struct platform_device smdk_led5 = { + .name = "s3c24xx_led", + .id = 1, + .dev = { + .platform_data = &smdk_pdata_led5, + }, +}; + +static struct platform_device smdk_led6 = { + .name = "s3c24xx_led", + .id = 2, + .dev = { + .platform_data = &smdk_pdata_led6, + }, +}; + +static struct platform_device smdk_led7 = { + .name = "s3c24xx_led", + .id = 3, + .dev = { + .platform_data = &smdk_pdata_led7, + }, +}; + +/* NAND parititon from 2.4.18-swl5 */ + +static struct mtd_partition smdk_default_nand_part[] = { + [0] = { + .name = "Boot Agent", + .size = SZ_16K, + .offset = 0, + }, + [1] = { + .name = "S3C2410 flash partition 1", + .offset = 0, + .size = SZ_2M, + }, + [2] = { + .name = "S3C2410 flash partition 2", + .offset = SZ_4M, + .size = SZ_4M, + }, + [3] = { + .name = "S3C2410 flash partition 3", + .offset = SZ_8M, + .size = SZ_2M, + }, + [4] = { + .name = "S3C2410 flash partition 4", + .offset = SZ_1M * 10, + .size = SZ_4M, + }, + [5] = { + .name = "S3C2410 flash partition 5", + .offset = SZ_1M * 14, + .size = SZ_1M * 10, + }, + [6] = { + .name = "S3C2410 flash partition 6", + .offset = SZ_1M * 24, + .size = SZ_1M * 24, + }, + [7] = { + .name = "S3C2410 flash partition 7", + .offset = SZ_1M * 48, + .size = SZ_16M, + } +}; + +static struct s3c2410_nand_set smdk_nand_sets[] = { + [0] = { + .name = "NAND", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(smdk_default_nand_part), + .partitions = smdk_default_nand_part, + }, +}; + +/* choose a set of timings which should suit most 512Mbit + * chips and beyond. +*/ + +static struct s3c2410_platform_nand smdk_nand_info = { + .tacls = 20, + .twrph0 = 60, + .twrph1 = 20, + .nr_sets = ARRAY_SIZE(smdk_nand_sets), + .sets = smdk_nand_sets, +}; + +/* devices we initialise */ + +static struct platform_device __initdata *smdk_devs[] = { + &s3c_device_nand, + &smdk_led4, + &smdk_led5, + &smdk_led6, + &smdk_led7, +}; + +void __init smdk_machine_init(void) +{ + /* Configure the LEDs (even if we have no LED support)*/ + + s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP); + s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP); + s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP); + s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP); + + s3c2410_gpio_setpin(S3C2410_GPF4, 1); + s3c2410_gpio_setpin(S3C2410_GPF5, 1); + s3c2410_gpio_setpin(S3C2410_GPF6, 1); + s3c2410_gpio_setpin(S3C2410_GPF7, 1); + + s3c_device_nand.dev.platform_data = &smdk_nand_info; + + platform_add_devices(smdk_devs, ARRAY_SIZE(smdk_devs)); + + s3c2410_pm_init(); +} diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c new file mode 100644 index 000000000000..2fbb74969379 --- /dev/null +++ b/arch/arm/plat-s3c24xx/cpu.c @@ -0,0 +1,357 @@ +/* linux/arch/arm/plat-s3c24xx/cpu.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * http://www.simtec.co.uk/products/SWLINUX/ + * Ben Dooks + * + * S3C24XX CPU Support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include + +#include +#include + +#include +#include +#include +#include +#include +#include +#include "s3c244x.h" +#include +#include + +struct cpu_table { + unsigned long idcode; + unsigned long idmask; + void (*map_io)(struct map_desc *mach_desc, int size); + void (*init_uarts)(struct s3c2410_uartcfg *cfg, int no); + void (*init_clocks)(int xtal); + int (*init)(void); + const char *name; +}; + +/* table of supported CPUs */ + +static const char name_s3c2400[] = "S3C2400"; +static const char name_s3c2410[] = "S3C2410"; +static const char name_s3c2412[] = "S3C2412"; +static const char name_s3c2440[] = "S3C2440"; +static const char name_s3c2442[] = "S3C2442"; +static const char name_s3c2410a[] = "S3C2410A"; +static const char name_s3c2440a[] = "S3C2440A"; + +static struct cpu_table cpu_ids[] __initdata = { + { + .idcode = 0x32410000, + .idmask = 0xffffffff, + .map_io = s3c2410_map_io, + .init_clocks = s3c2410_init_clocks, + .init_uarts = s3c2410_init_uarts, + .init = s3c2410_init, + .name = name_s3c2410 + }, + { + .idcode = 0x32410002, + .idmask = 0xffffffff, + .map_io = s3c2410_map_io, + .init_clocks = s3c2410_init_clocks, + .init_uarts = s3c2410_init_uarts, + .init = s3c2410_init, + .name = name_s3c2410a + }, + { + .idcode = 0x32440000, + .idmask = 0xffffffff, + .map_io = s3c244x_map_io, + .init_clocks = s3c244x_init_clocks, + .init_uarts = s3c244x_init_uarts, + .init = s3c2440_init, + .name = name_s3c2440 + }, + { + .idcode = 0x32440001, + .idmask = 0xffffffff, + .map_io = s3c244x_map_io, + .init_clocks = s3c244x_init_clocks, + .init_uarts = s3c244x_init_uarts, + .init = s3c2440_init, + .name = name_s3c2440a + }, + { + .idcode = 0x32440aaa, + .idmask = 0xffffffff, + .map_io = s3c244x_map_io, + .init_clocks = s3c244x_init_clocks, + .init_uarts = s3c244x_init_uarts, + .init = s3c2442_init, + .name = name_s3c2442 + }, + { + .idcode = 0x32412001, + .idmask = 0xffffffff, + .map_io = s3c2412_map_io, + .init_clocks = s3c2412_init_clocks, + .init_uarts = s3c2412_init_uarts, + .init = s3c2412_init, + .name = name_s3c2412, + }, + { /* a newer version of the s3c2412 */ + .idcode = 0x32412003, + .idmask = 0xffffffff, + .map_io = s3c2412_map_io, + .init_clocks = s3c2412_init_clocks, + .init_uarts = s3c2412_init_uarts, + .init = s3c2412_init, + .name = name_s3c2412, + }, + { + .idcode = 0x0, /* S3C2400 doesn't have an idcode */ + .idmask = 0xffffffff, + .map_io = s3c2400_map_io, + .init_clocks = s3c2400_init_clocks, + .init_uarts = s3c2400_init_uarts, + .init = s3c2400_init, + .name = name_s3c2400 + }, +}; + +/* minimal IO mapping */ + +static struct map_desc s3c_iodesc[] __initdata = { + IODESC_ENT(GPIO), + IODESC_ENT(IRQ), + IODESC_ENT(MEMCTRL), + IODESC_ENT(UART) +}; + + +static struct cpu_table * +s3c_lookup_cpu(unsigned long idcode) +{ + struct cpu_table *tab; + int count; + + tab = cpu_ids; + for (count = 0; count < ARRAY_SIZE(cpu_ids); count++, tab++) { + if ((idcode & tab->idmask) == tab->idcode) + return tab; + } + + return NULL; +} + +/* board information */ + +static struct s3c24xx_board *board; + +void s3c24xx_set_board(struct s3c24xx_board *b) +{ + int i; + + board = b; + + if (b->clocks_count != 0) { + struct clk **ptr = b->clocks; + + for (i = b->clocks_count; i > 0; i--, ptr++) + s3c24xx_register_clock(*ptr); + } +} + +/* cpu information */ + +static struct cpu_table *cpu; + +static unsigned long s3c24xx_read_idcode_v5(void) +{ +#if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413) + return __raw_readl(S3C2412_GSTATUS1); +#else + return 1UL; /* don't look like an 2400 */ +#endif +} + +static unsigned long s3c24xx_read_idcode_v4(void) +{ +#ifndef CONFIG_CPU_S3C2400 + return __raw_readl(S3C2410_GSTATUS1); +#else + return 0UL; +#endif +} + +void __init s3c24xx_init_io(struct map_desc *mach_desc, int size) +{ + unsigned long idcode = 0x0; + + /* initialise the io descriptors we need for initialisation */ + iotable_init(s3c_iodesc, ARRAY_SIZE(s3c_iodesc)); + + if (cpu_architecture() >= CPU_ARCH_ARMv5) { + idcode = s3c24xx_read_idcode_v5(); + } else { + idcode = s3c24xx_read_idcode_v4(); + } + + cpu = s3c_lookup_cpu(idcode); + + if (cpu == NULL) { + printk(KERN_ERR "Unknown CPU type 0x%08lx\n", idcode); + panic("Unknown S3C24XX CPU"); + } + + printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode); + + if (cpu->map_io == NULL || cpu->init == NULL) { + printk(KERN_ERR "CPU %s support not enabled\n", cpu->name); + panic("Unsupported S3C24XX CPU"); + } + + (cpu->map_io)(mach_desc, size); +} + +/* s3c24xx_init_clocks + * + * Initialise the clock subsystem and associated information from the + * given master crystal value. + * + * xtal = 0 -> use default PLL crystal value (normally 12MHz) + * != 0 -> PLL crystal value in Hz +*/ + +void __init s3c24xx_init_clocks(int xtal) +{ + if (xtal == 0) + xtal = 12*1000*1000; + + if (cpu == NULL) + panic("s3c24xx_init_clocks: no cpu setup?\n"); + + if (cpu->init_clocks == NULL) + panic("s3c24xx_init_clocks: cpu has no clock init\n"); + else + (cpu->init_clocks)(xtal); +} + +/* uart management */ + +static int nr_uarts __initdata = 0; + +static struct s3c2410_uartcfg uart_cfgs[3]; + +/* s3c24xx_init_uartdevs + * + * copy the specified platform data and configuration into our central + * set of devices, before the data is thrown away after the init process. + * + * This also fills in the array passed to the serial driver for the + * early initialisation of the console. +*/ + +void __init s3c24xx_init_uartdevs(char *name, + struct s3c24xx_uart_resources *res, + struct s3c2410_uartcfg *cfg, int no) +{ + struct platform_device *platdev; + struct s3c2410_uartcfg *cfgptr = uart_cfgs; + struct s3c24xx_uart_resources *resp; + int uart; + + memcpy(cfgptr, cfg, sizeof(struct s3c2410_uartcfg) * no); + + for (uart = 0; uart < no; uart++, cfg++, cfgptr++) { + platdev = s3c24xx_uart_src[cfgptr->hwport]; + + resp = res + cfgptr->hwport; + + s3c24xx_uart_devs[uart] = platdev; + + platdev->name = name; + platdev->resource = resp->resources; + platdev->num_resources = resp->nr_resources; + + platdev->dev.platform_data = cfgptr; + } + + nr_uarts = no; +} + +void __init s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no) +{ + if (cpu == NULL) + return; + + if (cpu->init_uarts == NULL) { + printk(KERN_ERR "s3c24xx_init_uarts: cpu has no uart init\n"); + } else + (cpu->init_uarts)(cfg, no); +} + +static int __init s3c_arch_init(void) +{ + int ret; + + // do the correct init for cpu + + if (cpu == NULL) + panic("s3c_arch_init: NULL cpu\n"); + + ret = (cpu->init)(); + if (ret != 0) + return ret; + + ret = platform_add_devices(s3c24xx_uart_devs, nr_uarts); + if (ret != 0) + return ret; + + if (board != NULL) { + struct platform_device **ptr = board->devices; + int i; + + for (i = 0; i < board->devices_count; i++, ptr++) { + ret = platform_device_register(*ptr); + + if (ret) { + printk(KERN_ERR "s3c24xx: failed to add board device %s (%d) @%p\n", (*ptr)->name, ret, *ptr); + } + } + + /* mask any error, we may not need all these board + * devices */ + ret = 0; + } + + return ret; +} + +arch_initcall(s3c_arch_init); diff --git a/arch/arm/plat-s3c24xx/devs.c b/arch/arm/plat-s3c24xx/devs.c new file mode 100644 index 000000000000..6d46c4e2a4f7 --- /dev/null +++ b/arch/arm/plat-s3c24xx/devs.c @@ -0,0 +1,585 @@ +/* linux/arch/arm/plat-s3c24xx/devs.c + * + * Copyright (c) 2004 Simtec Electronics + * Ben Dooks + * + * Base S3C24XX platform device definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include + +/* Serial port registrations */ + +static struct resource s3c2410_uart0_resource[] = { + [0] = { + .start = S3C2410_PA_UART0, + .end = S3C2410_PA_UART0 + 0x3fff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_S3CUART_RX0, + .end = IRQ_S3CUART_ERR0, + .flags = IORESOURCE_IRQ, + } +}; + +static struct resource s3c2410_uart1_resource[] = { + [0] = { + .start = S3C2410_PA_UART1, + .end = S3C2410_PA_UART1 + 0x3fff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_S3CUART_RX1, + .end = IRQ_S3CUART_ERR1, + .flags = IORESOURCE_IRQ, + } +}; + +static struct resource s3c2410_uart2_resource[] = { + [0] = { + .start = S3C2410_PA_UART2, + .end = S3C2410_PA_UART2 + 0x3fff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_S3CUART_RX2, + .end = IRQ_S3CUART_ERR2, + .flags = IORESOURCE_IRQ, + } +}; + +struct s3c24xx_uart_resources s3c2410_uart_resources[] __initdata = { + [0] = { + .resources = s3c2410_uart0_resource, + .nr_resources = ARRAY_SIZE(s3c2410_uart0_resource), + }, + [1] = { + .resources = s3c2410_uart1_resource, + .nr_resources = ARRAY_SIZE(s3c2410_uart1_resource), + }, + [2] = { + .resources = s3c2410_uart2_resource, + .nr_resources = ARRAY_SIZE(s3c2410_uart2_resource), + }, +}; + +/* yart devices */ + +static struct platform_device s3c24xx_uart_device0 = { + .id = 0, +}; + +static struct platform_device s3c24xx_uart_device1 = { + .id = 1, +}; + +static struct platform_device s3c24xx_uart_device2 = { + .id = 2, +}; + +struct platform_device *s3c24xx_uart_src[3] = { + &s3c24xx_uart_device0, + &s3c24xx_uart_device1, + &s3c24xx_uart_device2, +}; + +struct platform_device *s3c24xx_uart_devs[3] = { +}; + +/* USB Host Controller */ + +static struct resource s3c_usb_resource[] = { + [0] = { + .start = S3C24XX_PA_USBHOST, + .end = S3C24XX_PA_USBHOST + S3C24XX_SZ_USBHOST - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_USBH, + .end = IRQ_USBH, + .flags = IORESOURCE_IRQ, + } +}; + +static u64 s3c_device_usb_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_usb = { + .name = "s3c2410-ohci", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_usb_resource), + .resource = s3c_usb_resource, + .dev = { + .dma_mask = &s3c_device_usb_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_usb); + +/* LCD Controller */ + +static struct resource s3c_lcd_resource[] = { + [0] = { + .start = S3C24XX_PA_LCD, + .end = S3C24XX_PA_LCD + S3C24XX_SZ_LCD - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_LCD, + .end = IRQ_LCD, + .flags = IORESOURCE_IRQ, + } + +}; + +static u64 s3c_device_lcd_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_lcd = { + .name = "s3c2410-lcd", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_lcd_resource), + .resource = s3c_lcd_resource, + .dev = { + .dma_mask = &s3c_device_lcd_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_lcd); + +void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *pd) +{ + struct s3c2410fb_mach_info *npd; + + npd = kmalloc(sizeof(*npd), GFP_KERNEL); + if (npd) { + memcpy(npd, pd, sizeof(*npd)); + s3c_device_lcd.dev.platform_data = npd; + } else { + printk(KERN_ERR "no memory for LCD platform data\n"); + } +} + +/* NAND Controller */ + +static struct resource s3c_nand_resource[] = { + [0] = { + .start = S3C2410_PA_NAND, + .end = S3C2410_PA_NAND + S3C24XX_SZ_NAND - 1, + .flags = IORESOURCE_MEM, + } +}; + +struct platform_device s3c_device_nand = { + .name = "s3c2410-nand", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_nand_resource), + .resource = s3c_nand_resource, +}; + +EXPORT_SYMBOL(s3c_device_nand); + +/* USB Device (Gadget)*/ + +static struct resource s3c_usbgadget_resource[] = { + [0] = { + .start = S3C24XX_PA_USBDEV, + .end = S3C24XX_PA_USBDEV + S3C24XX_SZ_USBDEV - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_USBD, + .end = IRQ_USBD, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_usbgadget = { + .name = "s3c2410-usbgadget", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_usbgadget_resource), + .resource = s3c_usbgadget_resource, +}; + +EXPORT_SYMBOL(s3c_device_usbgadget); + +/* Watchdog */ + +static struct resource s3c_wdt_resource[] = { + [0] = { + .start = S3C24XX_PA_WATCHDOG, + .end = S3C24XX_PA_WATCHDOG + S3C24XX_SZ_WATCHDOG - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_WDT, + .end = IRQ_WDT, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_wdt = { + .name = "s3c2410-wdt", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_wdt_resource), + .resource = s3c_wdt_resource, +}; + +EXPORT_SYMBOL(s3c_device_wdt); + +/* I2C */ + +static struct resource s3c_i2c_resource[] = { + [0] = { + .start = S3C24XX_PA_IIC, + .end = S3C24XX_PA_IIC + S3C24XX_SZ_IIC - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_IIC, + .end = IRQ_IIC, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_i2c = { + .name = "s3c2410-i2c", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_i2c_resource), + .resource = s3c_i2c_resource, +}; + +EXPORT_SYMBOL(s3c_device_i2c); + +/* IIS */ + +static struct resource s3c_iis_resource[] = { + [0] = { + .start = S3C24XX_PA_IIS, + .end = S3C24XX_PA_IIS + S3C24XX_SZ_IIS -1, + .flags = IORESOURCE_MEM, + } +}; + +static u64 s3c_device_iis_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_iis = { + .name = "s3c2410-iis", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_iis_resource), + .resource = s3c_iis_resource, + .dev = { + .dma_mask = &s3c_device_iis_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_iis); + +/* RTC */ + +static struct resource s3c_rtc_resource[] = { + [0] = { + .start = S3C24XX_PA_RTC, + .end = S3C24XX_PA_RTC + 0xff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_RTC, + .end = IRQ_RTC, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .start = IRQ_TICK, + .end = IRQ_TICK, + .flags = IORESOURCE_IRQ + } +}; + +struct platform_device s3c_device_rtc = { + .name = "s3c2410-rtc", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_rtc_resource), + .resource = s3c_rtc_resource, +}; + +EXPORT_SYMBOL(s3c_device_rtc); + +/* ADC */ + +static struct resource s3c_adc_resource[] = { + [0] = { + .start = S3C24XX_PA_ADC, + .end = S3C24XX_PA_ADC + S3C24XX_SZ_ADC - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TC, + .end = IRQ_TC, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .start = IRQ_ADC, + .end = IRQ_ADC, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_adc = { + .name = "s3c2410-adc", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_adc_resource), + .resource = s3c_adc_resource, +}; + +/* SDI */ + +static struct resource s3c_sdi_resource[] = { + [0] = { + .start = S3C2410_PA_SDI, + .end = S3C2410_PA_SDI + S3C24XX_SZ_SDI - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_SDI, + .end = IRQ_SDI, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_sdi = { + .name = "s3c2410-sdi", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_sdi_resource), + .resource = s3c_sdi_resource, +}; + +EXPORT_SYMBOL(s3c_device_sdi); + +/* SPI (0) */ + +static struct resource s3c_spi0_resource[] = { + [0] = { + .start = S3C24XX_PA_SPI, + .end = S3C24XX_PA_SPI + 0x1f, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_SPI0, + .end = IRQ_SPI0, + .flags = IORESOURCE_IRQ, + } + +}; + +static u64 s3c_device_spi0_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_spi0 = { + .name = "s3c2410-spi", + .id = 0, + .num_resources = ARRAY_SIZE(s3c_spi0_resource), + .resource = s3c_spi0_resource, + .dev = { + .dma_mask = &s3c_device_spi0_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_spi0); + +/* SPI (1) */ + +static struct resource s3c_spi1_resource[] = { + [0] = { + .start = S3C24XX_PA_SPI + 0x20, + .end = S3C24XX_PA_SPI + 0x20 + 0x1f, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_SPI1, + .end = IRQ_SPI1, + .flags = IORESOURCE_IRQ, + } + +}; + +static u64 s3c_device_spi1_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_spi1 = { + .name = "s3c2410-spi", + .id = 1, + .num_resources = ARRAY_SIZE(s3c_spi1_resource), + .resource = s3c_spi1_resource, + .dev = { + .dma_mask = &s3c_device_spi1_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_spi1); + +/* pwm timer blocks */ + +static struct resource s3c_timer0_resource[] = { + [0] = { + .start = S3C24XX_PA_TIMER + 0x0C, + .end = S3C24XX_PA_TIMER + 0x0C + 0xB, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TIMER0, + .end = IRQ_TIMER0, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_timer0 = { + .name = "s3c2410-timer", + .id = 0, + .num_resources = ARRAY_SIZE(s3c_timer0_resource), + .resource = s3c_timer0_resource, +}; + +EXPORT_SYMBOL(s3c_device_timer0); + +/* timer 1 */ + +static struct resource s3c_timer1_resource[] = { + [0] = { + .start = S3C24XX_PA_TIMER + 0x18, + .end = S3C24XX_PA_TIMER + 0x23, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TIMER1, + .end = IRQ_TIMER1, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_timer1 = { + .name = "s3c2410-timer", + .id = 1, + .num_resources = ARRAY_SIZE(s3c_timer1_resource), + .resource = s3c_timer1_resource, +}; + +EXPORT_SYMBOL(s3c_device_timer1); + +/* timer 2 */ + +static struct resource s3c_timer2_resource[] = { + [0] = { + .start = S3C24XX_PA_TIMER + 0x24, + .end = S3C24XX_PA_TIMER + 0x2F, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TIMER2, + .end = IRQ_TIMER2, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_timer2 = { + .name = "s3c2410-timer", + .id = 2, + .num_resources = ARRAY_SIZE(s3c_timer2_resource), + .resource = s3c_timer2_resource, +}; + +EXPORT_SYMBOL(s3c_device_timer2); + +/* timer 3 */ + +static struct resource s3c_timer3_resource[] = { + [0] = { + .start = S3C24XX_PA_TIMER + 0x30, + .end = S3C24XX_PA_TIMER + 0x3B, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TIMER3, + .end = IRQ_TIMER3, + .flags = IORESOURCE_IRQ, + } + +}; + +struct platform_device s3c_device_timer3 = { + .name = "s3c2410-timer", + .id = 3, + .num_resources = ARRAY_SIZE(s3c_timer3_resource), + .resource = s3c_timer3_resource, +}; + +EXPORT_SYMBOL(s3c_device_timer3); + +#ifdef CONFIG_CPU_S3C2440 + +/* Camif Controller */ + +static struct resource s3c_camif_resource[] = { + [0] = { + .start = S3C2440_PA_CAMIF, + .end = S3C2440_PA_CAMIF + S3C2440_SZ_CAMIF - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_CAM, + .end = IRQ_CAM, + .flags = IORESOURCE_IRQ, + } + +}; + +static u64 s3c_device_camif_dmamask = 0xffffffffUL; + +struct platform_device s3c_device_camif = { + .name = "s3c2440-camif", + .id = -1, + .num_resources = ARRAY_SIZE(s3c_camif_resource), + .resource = s3c_camif_resource, + .dev = { + .dma_mask = &s3c_device_camif_dmamask, + .coherent_dma_mask = 0xffffffffUL + } +}; + +EXPORT_SYMBOL(s3c_device_camif); + +#endif // CONFIG_CPU_S32440 diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c new file mode 100644 index 000000000000..c784e1f816bb --- /dev/null +++ b/arch/arm/plat-s3c24xx/dma.c @@ -0,0 +1,1441 @@ +/* linux/arch/arm/plat-s3c24xx/dma.c + * + * Copyright (c) 2003-2005,2006 Simtec Electronics + * Ben Dooks + * + * S3C2410 DMA core + * + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + + +#ifdef CONFIG_S3C2410_DMA_DEBUG +#define DEBUG +#endif + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include + +#include + +/* io map for dma */ +static void __iomem *dma_base; +static struct kmem_cache *dma_kmem; + +struct s3c24xx_dma_selection dma_sel; + +/* dma channel state information */ +struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; + +/* debugging functions */ + +#define BUF_MAGIC (0xcafebabe) + +#define dmawarn(fmt...) printk(KERN_DEBUG fmt) + +#define dma_regaddr(chan, reg) ((chan)->regs + (reg)) + +#if 1 +#define dma_wrreg(chan, reg, val) writel((val), (chan)->regs + (reg)) +#else +static inline void +dma_wrreg(struct s3c2410_dma_chan *chan, int reg, unsigned long val) +{ + pr_debug("writing %08x to register %08x\n",(unsigned int)val,reg); + writel(val, dma_regaddr(chan, reg)); +} +#endif + +#define dma_rdreg(chan, reg) readl((chan)->regs + (reg)) + +/* captured register state for debug */ + +struct s3c2410_dma_regstate { + unsigned long dcsrc; + unsigned long disrc; + unsigned long dstat; + unsigned long dcon; + unsigned long dmsktrig; +}; + +#ifdef CONFIG_S3C2410_DMA_DEBUG + +/* dmadbg_showregs + * + * simple debug routine to print the current state of the dma registers +*/ + +static void +dmadbg_capture(struct s3c2410_dma_chan *chan, struct s3c2410_dma_regstate *regs) +{ + regs->dcsrc = dma_rdreg(chan, S3C2410_DMA_DCSRC); + regs->disrc = dma_rdreg(chan, S3C2410_DMA_DISRC); + regs->dstat = dma_rdreg(chan, S3C2410_DMA_DSTAT); + regs->dcon = dma_rdreg(chan, S3C2410_DMA_DCON); + regs->dmsktrig = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); +} + +static void +dmadbg_dumpregs(const char *fname, int line, struct s3c2410_dma_chan *chan, + struct s3c2410_dma_regstate *regs) +{ + printk(KERN_DEBUG "dma%d: %s:%d: DCSRC=%08lx, DISRC=%08lx, DSTAT=%08lx DMT=%02lx, DCON=%08lx\n", + chan->number, fname, line, + regs->dcsrc, regs->disrc, regs->dstat, regs->dmsktrig, + regs->dcon); +} + +static void +dmadbg_showchan(const char *fname, int line, struct s3c2410_dma_chan *chan) +{ + struct s3c2410_dma_regstate state; + + dmadbg_capture(chan, &state); + + printk(KERN_DEBUG "dma%d: %s:%d: ls=%d, cur=%p, %p %p\n", + chan->number, fname, line, chan->load_state, + chan->curr, chan->next, chan->end); + + dmadbg_dumpregs(fname, line, chan, &state); +} + +static void +dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan) +{ + struct s3c2410_dma_regstate state; + + dmadbg_capture(chan, &state); + dmadbg_dumpregs(fname, line, chan, &state); +} + +#define dbg_showregs(chan) dmadbg_showregs(__FUNCTION__, __LINE__, (chan)) +#define dbg_showchan(chan) dmadbg_showchan(__FUNCTION__, __LINE__, (chan)) +#else +#define dbg_showregs(chan) do { } while(0) +#define dbg_showchan(chan) do { } while(0) +#endif /* CONFIG_S3C2410_DMA_DEBUG */ + +static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX]; + +/* lookup_dma_channel + * + * change the dma channel number given into a real dma channel id +*/ + +static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel) +{ + if (channel & DMACH_LOW_LEVEL) + return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL]; + else + return dma_chan_map[channel]; +} + +/* s3c2410_dma_stats_timeout + * + * Update DMA stats from timeout info +*/ + +static void +s3c2410_dma_stats_timeout(struct s3c2410_dma_stats *stats, int val) +{ + if (stats == NULL) + return; + + if (val > stats->timeout_longest) + stats->timeout_longest = val; + if (val < stats->timeout_shortest) + stats->timeout_shortest = val; + + stats->timeout_avg += val; +} + +/* s3c2410_dma_waitforload + * + * wait for the DMA engine to load a buffer, and update the state accordingly +*/ + +static int +s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line) +{ + int timeout = chan->load_timeout; + int took; + + if (chan->load_state != S3C2410_DMALOAD_1LOADED) { + printk(KERN_ERR "dma%d: s3c2410_dma_waitforload() called in loadstate %d from line %d\n", chan->number, chan->load_state, line); + return 0; + } + + if (chan->stats != NULL) + chan->stats->loads++; + + while (--timeout > 0) { + if ((dma_rdreg(chan, S3C2410_DMA_DSTAT) << (32-20)) != 0) { + took = chan->load_timeout - timeout; + + s3c2410_dma_stats_timeout(chan->stats, took); + + switch (chan->load_state) { + case S3C2410_DMALOAD_1LOADED: + chan->load_state = S3C2410_DMALOAD_1RUNNING; + break; + + default: + printk(KERN_ERR "dma%d: unknown load_state in s3c2410_dma_waitforload() %d\n", chan->number, chan->load_state); + } + + return 1; + } + } + + if (chan->stats != NULL) { + chan->stats->timeout_failed++; + } + + return 0; +} + + + +/* s3c2410_dma_loadbuffer + * + * load a buffer, and update the channel state +*/ + +static inline int +s3c2410_dma_loadbuffer(struct s3c2410_dma_chan *chan, + struct s3c2410_dma_buf *buf) +{ + unsigned long reload; + + pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n", + buf, (unsigned long)buf->data, buf->size); + + if (buf == NULL) { + dmawarn("buffer is NULL\n"); + return -EINVAL; + } + + /* check the state of the channel before we do anything */ + + if (chan->load_state == S3C2410_DMALOAD_1LOADED) { + dmawarn("load_state is S3C2410_DMALOAD_1LOADED\n"); + } + + if (chan->load_state == S3C2410_DMALOAD_1LOADED_1RUNNING) { + dmawarn("state is S3C2410_DMALOAD_1LOADED_1RUNNING\n"); + } + + /* it would seem sensible if we are the last buffer to not bother + * with the auto-reload bit, so that the DMA engine will not try + * and load another transfer after this one has finished... + */ + if (chan->load_state == S3C2410_DMALOAD_NONE) { + pr_debug("load_state is none, checking for noreload (next=%p)\n", + buf->next); + reload = (buf->next == NULL) ? S3C2410_DCON_NORELOAD : 0; + } else { + //pr_debug("load_state is %d => autoreload\n", chan->load_state); + reload = S3C2410_DCON_AUTORELOAD; + } + + if ((buf->data & 0xf0000000) != 0x30000000) { + dmawarn("dmaload: buffer is %p\n", (void *)buf->data); + } + + writel(buf->data, chan->addr_reg); + + dma_wrreg(chan, S3C2410_DMA_DCON, + chan->dcon | reload | (buf->size/chan->xfer_unit)); + + chan->next = buf->next; + + /* update the state of the channel */ + + switch (chan->load_state) { + case S3C2410_DMALOAD_NONE: + chan->load_state = S3C2410_DMALOAD_1LOADED; + break; + + case S3C2410_DMALOAD_1RUNNING: + chan->load_state = S3C2410_DMALOAD_1LOADED_1RUNNING; + break; + + default: + dmawarn("dmaload: unknown state %d in loadbuffer\n", + chan->load_state); + break; + } + + return 0; +} + +/* s3c2410_dma_call_op + * + * small routine to call the op routine with the given op if it has been + * registered +*/ + +static void +s3c2410_dma_call_op(struct s3c2410_dma_chan *chan, enum s3c2410_chan_op op) +{ + if (chan->op_fn != NULL) { + (chan->op_fn)(chan, op); + } +} + +/* s3c2410_dma_buffdone + * + * small wrapper to check if callback routine needs to be called, and + * if so, call it +*/ + +static inline void +s3c2410_dma_buffdone(struct s3c2410_dma_chan *chan, struct s3c2410_dma_buf *buf, + enum s3c2410_dma_buffresult result) +{ +#if 0 + pr_debug("callback_fn=%p, buf=%p, id=%p, size=%d, result=%d\n", + chan->callback_fn, buf, buf->id, buf->size, result); +#endif + + if (chan->callback_fn != NULL) { + (chan->callback_fn)(chan, buf->id, buf->size, result); + } +} + +/* s3c2410_dma_start + * + * start a dma channel going +*/ + +static int s3c2410_dma_start(struct s3c2410_dma_chan *chan) +{ + unsigned long tmp; + unsigned long flags; + + pr_debug("s3c2410_start_dma: channel=%d\n", chan->number); + + local_irq_save(flags); + + if (chan->state == S3C2410_DMA_RUNNING) { + pr_debug("s3c2410_start_dma: already running (%d)\n", chan->state); + local_irq_restore(flags); + return 0; + } + + chan->state = S3C2410_DMA_RUNNING; + + /* check wether there is anything to load, and if not, see + * if we can find anything to load + */ + + if (chan->load_state == S3C2410_DMALOAD_NONE) { + if (chan->next == NULL) { + printk(KERN_ERR "dma%d: channel has nothing loaded\n", + chan->number); + chan->state = S3C2410_DMA_IDLE; + local_irq_restore(flags); + return -EINVAL; + } + + s3c2410_dma_loadbuffer(chan, chan->next); + } + + dbg_showchan(chan); + + /* enable the channel */ + + if (!chan->irq_enabled) { + enable_irq(chan->irq); + chan->irq_enabled = 1; + } + + /* start the channel going */ + + tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); + tmp &= ~S3C2410_DMASKTRIG_STOP; + tmp |= S3C2410_DMASKTRIG_ON; + dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp); + + pr_debug("dma%d: %08lx to DMASKTRIG\n", chan->number, tmp); + +#if 0 + /* the dma buffer loads should take care of clearing the AUTO + * reloading feature */ + tmp = dma_rdreg(chan, S3C2410_DMA_DCON); + tmp &= ~S3C2410_DCON_NORELOAD; + dma_wrreg(chan, S3C2410_DMA_DCON, tmp); +#endif + + s3c2410_dma_call_op(chan, S3C2410_DMAOP_START); + + dbg_showchan(chan); + + /* if we've only loaded one buffer onto the channel, then chec + * to see if we have another, and if so, try and load it so when + * the first buffer is finished, the new one will be loaded onto + * the channel */ + + if (chan->next != NULL) { + if (chan->load_state == S3C2410_DMALOAD_1LOADED) { + + if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { + pr_debug("%s: buff not yet loaded, no more todo\n", + __FUNCTION__); + } else { + chan->load_state = S3C2410_DMALOAD_1RUNNING; + s3c2410_dma_loadbuffer(chan, chan->next); + } + + } else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) { + s3c2410_dma_loadbuffer(chan, chan->next); + } + } + + + local_irq_restore(flags); + + return 0; +} + +/* s3c2410_dma_canload + * + * work out if we can queue another buffer into the DMA engine +*/ + +static int +s3c2410_dma_canload(struct s3c2410_dma_chan *chan) +{ + if (chan->load_state == S3C2410_DMALOAD_NONE || + chan->load_state == S3C2410_DMALOAD_1RUNNING) + return 1; + + return 0; +} + +/* s3c2410_dma_enqueue + * + * queue an given buffer for dma transfer. + * + * id the device driver's id information for this buffer + * data the physical address of the buffer data + * size the size of the buffer in bytes + * + * If the channel is not running, then the flag S3C2410_DMAF_AUTOSTART + * is checked, and if set, the channel is started. If this flag isn't set, + * then an error will be returned. + * + * It is possible to queue more than one DMA buffer onto a channel at + * once, and the code will deal with the re-loading of the next buffer + * when necessary. +*/ + +int s3c2410_dma_enqueue(unsigned int channel, void *id, + dma_addr_t data, int size) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + struct s3c2410_dma_buf *buf; + unsigned long flags; + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: id=%p, data=%08x, size=%d\n", + __FUNCTION__, id, (unsigned int)data, size); + + buf = kmem_cache_alloc(dma_kmem, GFP_ATOMIC); + if (buf == NULL) { + pr_debug("%s: out of memory (%ld alloc)\n", + __FUNCTION__, (long)sizeof(*buf)); + return -ENOMEM; + } + + //pr_debug("%s: new buffer %p\n", __FUNCTION__, buf); + //dbg_showchan(chan); + + buf->next = NULL; + buf->data = buf->ptr = data; + buf->size = size; + buf->id = id; + buf->magic = BUF_MAGIC; + + local_irq_save(flags); + + if (chan->curr == NULL) { + /* we've got nothing loaded... */ + pr_debug("%s: buffer %p queued onto empty channel\n", + __FUNCTION__, buf); + + chan->curr = buf; + chan->end = buf; + chan->next = NULL; + } else { + pr_debug("dma%d: %s: buffer %p queued onto non-empty channel\n", + chan->number, __FUNCTION__, buf); + + if (chan->end == NULL) + pr_debug("dma%d: %s: %p not empty, and chan->end==NULL?\n", + chan->number, __FUNCTION__, chan); + + chan->end->next = buf; + chan->end = buf; + } + + /* if necessary, update the next buffer field */ + if (chan->next == NULL) + chan->next = buf; + + /* check to see if we can load a buffer */ + if (chan->state == S3C2410_DMA_RUNNING) { + if (chan->load_state == S3C2410_DMALOAD_1LOADED && 1) { + if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { + printk(KERN_ERR "dma%d: loadbuffer:" + "timeout loading buffer\n", + chan->number); + dbg_showchan(chan); + local_irq_restore(flags); + return -EINVAL; + } + } + + while (s3c2410_dma_canload(chan) && chan->next != NULL) { + s3c2410_dma_loadbuffer(chan, chan->next); + } + } else if (chan->state == S3C2410_DMA_IDLE) { + if (chan->flags & S3C2410_DMAF_AUTOSTART) { + s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_START); + } + } + + local_irq_restore(flags); + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_enqueue); + +static inline void +s3c2410_dma_freebuf(struct s3c2410_dma_buf *buf) +{ + int magicok = (buf->magic == BUF_MAGIC); + + buf->magic = -1; + + if (magicok) { + kmem_cache_free(dma_kmem, buf); + } else { + printk("s3c2410_dma_freebuf: buff %p with bad magic\n", buf); + } +} + +/* s3c2410_dma_lastxfer + * + * called when the system is out of buffers, to ensure that the channel + * is prepared for shutdown. +*/ + +static inline void +s3c2410_dma_lastxfer(struct s3c2410_dma_chan *chan) +{ +#if 0 + pr_debug("dma%d: s3c2410_dma_lastxfer: load_state %d\n", + chan->number, chan->load_state); +#endif + + switch (chan->load_state) { + case S3C2410_DMALOAD_NONE: + break; + + case S3C2410_DMALOAD_1LOADED: + if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { + /* flag error? */ + printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n", + chan->number, __FUNCTION__); + return; + } + break; + + case S3C2410_DMALOAD_1LOADED_1RUNNING: + /* I belive in this case we do not have anything to do + * until the next buffer comes along, and we turn off the + * reload */ + return; + + default: + pr_debug("dma%d: lastxfer: unhandled load_state %d with no next\n", + chan->number, chan->load_state); + return; + + } + + /* hopefully this'll shut the damned thing up after the transfer... */ + dma_wrreg(chan, S3C2410_DMA_DCON, chan->dcon | S3C2410_DCON_NORELOAD); +} + + +#define dmadbg2(x...) + +static irqreturn_t +s3c2410_dma_irq(int irq, void *devpw) +{ + struct s3c2410_dma_chan *chan = (struct s3c2410_dma_chan *)devpw; + struct s3c2410_dma_buf *buf; + + buf = chan->curr; + + dbg_showchan(chan); + + /* modify the channel state */ + + switch (chan->load_state) { + case S3C2410_DMALOAD_1RUNNING: + /* TODO - if we are running only one buffer, we probably + * want to reload here, and then worry about the buffer + * callback */ + + chan->load_state = S3C2410_DMALOAD_NONE; + break; + + case S3C2410_DMALOAD_1LOADED: + /* iirc, we should go back to NONE loaded here, we + * had a buffer, and it was never verified as being + * loaded. + */ + + chan->load_state = S3C2410_DMALOAD_NONE; + break; + + case S3C2410_DMALOAD_1LOADED_1RUNNING: + /* we'll worry about checking to see if another buffer is + * ready after we've called back the owner. This should + * ensure we do not wait around too long for the DMA + * engine to start the next transfer + */ + + chan->load_state = S3C2410_DMALOAD_1LOADED; + break; + + case S3C2410_DMALOAD_NONE: + printk(KERN_ERR "dma%d: IRQ with no loaded buffer?\n", + chan->number); + break; + + default: + printk(KERN_ERR "dma%d: IRQ in invalid load_state %d\n", + chan->number, chan->load_state); + break; + } + + if (buf != NULL) { + /* update the chain to make sure that if we load any more + * buffers when we call the callback function, things should + * work properly */ + + chan->curr = buf->next; + buf->next = NULL; + + if (buf->magic != BUF_MAGIC) { + printk(KERN_ERR "dma%d: %s: buf %p incorrect magic\n", + chan->number, __FUNCTION__, buf); + return IRQ_HANDLED; + } + + s3c2410_dma_buffdone(chan, buf, S3C2410_RES_OK); + + /* free resouces */ + s3c2410_dma_freebuf(buf); + } else { + } + + /* only reload if the channel is still running... our buffer done + * routine may have altered the state by requesting the dma channel + * to stop or shutdown... */ + + /* todo: check that when the channel is shut-down from inside this + * function, we cope with unsetting reload, etc */ + + if (chan->next != NULL && chan->state != S3C2410_DMA_IDLE) { + unsigned long flags; + + switch (chan->load_state) { + case S3C2410_DMALOAD_1RUNNING: + /* don't need to do anything for this state */ + break; + + case S3C2410_DMALOAD_NONE: + /* can load buffer immediately */ + break; + + case S3C2410_DMALOAD_1LOADED: + if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { + /* flag error? */ + printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n", + chan->number, __FUNCTION__); + return IRQ_HANDLED; + } + + break; + + case S3C2410_DMALOAD_1LOADED_1RUNNING: + goto no_load; + + default: + printk(KERN_ERR "dma%d: unknown load_state in irq, %d\n", + chan->number, chan->load_state); + return IRQ_HANDLED; + } + + local_irq_save(flags); + s3c2410_dma_loadbuffer(chan, chan->next); + local_irq_restore(flags); + } else { + s3c2410_dma_lastxfer(chan); + + /* see if we can stop this channel.. */ + if (chan->load_state == S3C2410_DMALOAD_NONE) { + pr_debug("dma%d: end of transfer, stopping channel (%ld)\n", + chan->number, jiffies); + s3c2410_dma_ctrl(chan->number | DMACH_LOW_LEVEL, + S3C2410_DMAOP_STOP); + } + } + + no_load: + return IRQ_HANDLED; +} + +static struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel); + +/* s3c2410_request_dma + * + * get control of an dma channel +*/ + +int s3c2410_dma_request(unsigned int channel, + struct s3c2410_dma_client *client, + void *dev) +{ + struct s3c2410_dma_chan *chan; + unsigned long flags; + int err; + + pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n", + channel, client->name, dev); + + local_irq_save(flags); + + chan = s3c2410_dma_map_channel(channel); + if (chan == NULL) { + local_irq_restore(flags); + return -EBUSY; + } + + dbg_showchan(chan); + + chan->client = client; + chan->in_use = 1; + + if (!chan->irq_claimed) { + pr_debug("dma%d: %s : requesting irq %d\n", + channel, __FUNCTION__, chan->irq); + + chan->irq_claimed = 1; + local_irq_restore(flags); + + err = request_irq(chan->irq, s3c2410_dma_irq, IRQF_DISABLED, + client->name, (void *)chan); + + local_irq_save(flags); + + if (err) { + chan->in_use = 0; + chan->irq_claimed = 0; + local_irq_restore(flags); + + printk(KERN_ERR "%s: cannot get IRQ %d for DMA %d\n", + client->name, chan->irq, chan->number); + return err; + } + + chan->irq_enabled = 1; + } + + local_irq_restore(flags); + + /* need to setup */ + + pr_debug("%s: channel initialised, %p\n", __FUNCTION__, chan); + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_request); + +/* s3c2410_dma_free + * + * release the given channel back to the system, will stop and flush + * any outstanding transfers, and ensure the channel is ready for the + * next claimant. + * + * Note, although a warning is currently printed if the freeing client + * info is not the same as the registrant's client info, the free is still + * allowed to go through. +*/ + +int s3c2410_dma_free(dmach_t channel, struct s3c2410_dma_client *client) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + unsigned long flags; + + if (chan == NULL) + return -EINVAL; + + local_irq_save(flags); + + if (chan->client != client) { + printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n", + channel, chan->client, client); + } + + /* sort out stopping and freeing the channel */ + + if (chan->state != S3C2410_DMA_IDLE) { + pr_debug("%s: need to stop dma channel %p\n", + __FUNCTION__, chan); + + /* possibly flush the channel */ + s3c2410_dma_ctrl(channel, S3C2410_DMAOP_STOP); + } + + chan->client = NULL; + chan->in_use = 0; + + if (chan->irq_claimed) + free_irq(chan->irq, (void *)chan); + + chan->irq_claimed = 0; + + if (!(channel & DMACH_LOW_LEVEL)) + dma_chan_map[channel] = NULL; + + local_irq_restore(flags); + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_free); + +static int s3c2410_dma_dostop(struct s3c2410_dma_chan *chan) +{ + unsigned long flags; + unsigned long tmp; + + pr_debug("%s:\n", __FUNCTION__); + + dbg_showchan(chan); + + local_irq_save(flags); + + s3c2410_dma_call_op(chan, S3C2410_DMAOP_STOP); + + tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); + tmp |= S3C2410_DMASKTRIG_STOP; + //tmp &= ~S3C2410_DMASKTRIG_ON; + dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp); + +#if 0 + /* should also clear interrupts, according to WinCE BSP */ + tmp = dma_rdreg(chan, S3C2410_DMA_DCON); + tmp |= S3C2410_DCON_NORELOAD; + dma_wrreg(chan, S3C2410_DMA_DCON, tmp); +#endif + + /* should stop do this, or should we wait for flush? */ + chan->state = S3C2410_DMA_IDLE; + chan->load_state = S3C2410_DMALOAD_NONE; + + local_irq_restore(flags); + + return 0; +} + +void s3c2410_dma_waitforstop(struct s3c2410_dma_chan *chan) +{ + unsigned long tmp; + unsigned int timeout = 0x10000; + + while (timeout-- > 0) { + tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG); + + if (!(tmp & S3C2410_DMASKTRIG_ON)) + return; + } + + pr_debug("dma%d: failed to stop?\n", chan->number); +} + + +/* s3c2410_dma_flush + * + * stop the channel, and remove all current and pending transfers +*/ + +static int s3c2410_dma_flush(struct s3c2410_dma_chan *chan) +{ + struct s3c2410_dma_buf *buf, *next; + unsigned long flags; + + pr_debug("%s: chan %p (%d)\n", __FUNCTION__, chan, chan->number); + + dbg_showchan(chan); + + local_irq_save(flags); + + if (chan->state != S3C2410_DMA_IDLE) { + pr_debug("%s: stopping channel...\n", __FUNCTION__ ); + s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_STOP); + } + + buf = chan->curr; + if (buf == NULL) + buf = chan->next; + + chan->curr = chan->next = chan->end = NULL; + + if (buf != NULL) { + for ( ; buf != NULL; buf = next) { + next = buf->next; + + pr_debug("%s: free buffer %p, next %p\n", + __FUNCTION__, buf, buf->next); + + s3c2410_dma_buffdone(chan, buf, S3C2410_RES_ABORT); + s3c2410_dma_freebuf(buf); + } + } + + dbg_showregs(chan); + + s3c2410_dma_waitforstop(chan); + +#if 0 + /* should also clear interrupts, according to WinCE BSP */ + { + unsigned long tmp; + + tmp = dma_rdreg(chan, S3C2410_DMA_DCON); + tmp |= S3C2410_DCON_NORELOAD; + dma_wrreg(chan, S3C2410_DMA_DCON, tmp); + } +#endif + + dbg_showregs(chan); + + local_irq_restore(flags); + + return 0; +} + +int +s3c2410_dma_started(struct s3c2410_dma_chan *chan) +{ + unsigned long flags; + + local_irq_save(flags); + + dbg_showchan(chan); + + /* if we've only loaded one buffer onto the channel, then chec + * to see if we have another, and if so, try and load it so when + * the first buffer is finished, the new one will be loaded onto + * the channel */ + + if (chan->next != NULL) { + if (chan->load_state == S3C2410_DMALOAD_1LOADED) { + + if (s3c2410_dma_waitforload(chan, __LINE__) == 0) { + pr_debug("%s: buff not yet loaded, no more todo\n", + __FUNCTION__); + } else { + chan->load_state = S3C2410_DMALOAD_1RUNNING; + s3c2410_dma_loadbuffer(chan, chan->next); + } + + } else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) { + s3c2410_dma_loadbuffer(chan, chan->next); + } + } + + + local_irq_restore(flags); + + return 0; + +} + +int +s3c2410_dma_ctrl(dmach_t channel, enum s3c2410_chan_op op) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + if (chan == NULL) + return -EINVAL; + + switch (op) { + case S3C2410_DMAOP_START: + return s3c2410_dma_start(chan); + + case S3C2410_DMAOP_STOP: + return s3c2410_dma_dostop(chan); + + case S3C2410_DMAOP_PAUSE: + case S3C2410_DMAOP_RESUME: + return -ENOENT; + + case S3C2410_DMAOP_FLUSH: + return s3c2410_dma_flush(chan); + + case S3C2410_DMAOP_STARTED: + return s3c2410_dma_started(chan); + + case S3C2410_DMAOP_TIMEOUT: + return 0; + + } + + return -ENOENT; /* unknown, don't bother */ +} + +EXPORT_SYMBOL(s3c2410_dma_ctrl); + +/* DMA configuration for each channel + * + * DISRCC -> source of the DMA (AHB,APB) + * DISRC -> source address of the DMA + * DIDSTC -> destination of the DMA (AHB,APD) + * DIDST -> destination address of the DMA +*/ + +/* s3c2410_dma_config + * + * xfersize: size of unit in bytes (1,2,4) + * dcon: base value of the DCONx register +*/ + +int s3c2410_dma_config(dmach_t channel, + int xferunit, + int dcon) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n", + __FUNCTION__, channel, xferunit, dcon); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: Initial dcon is %08x\n", __FUNCTION__, dcon); + + dcon |= chan->dcon & dma_sel.dcon_mask; + + pr_debug("%s: New dcon is %08x\n", __FUNCTION__, dcon); + + switch (xferunit) { + case 1: + dcon |= S3C2410_DCON_BYTE; + break; + + case 2: + dcon |= S3C2410_DCON_HALFWORD; + break; + + case 4: + dcon |= S3C2410_DCON_WORD; + break; + + default: + pr_debug("%s: bad transfer size %d\n", __FUNCTION__, xferunit); + return -EINVAL; + } + + dcon |= S3C2410_DCON_HWTRIG; + dcon |= S3C2410_DCON_INTREQ; + + pr_debug("%s: dcon now %08x\n", __FUNCTION__, dcon); + + chan->dcon = dcon; + chan->xfer_unit = xferunit; + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_config); + +int s3c2410_dma_setflags(dmach_t channel, unsigned int flags) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: chan=%p, flags=%08x\n", __FUNCTION__, chan, flags); + + chan->flags = flags; + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_setflags); + + +/* do we need to protect the settings of the fields from + * irq? +*/ + +int s3c2410_dma_set_opfn(dmach_t channel, s3c2410_dma_opfn_t rtn) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: chan=%p, op rtn=%p\n", __FUNCTION__, chan, rtn); + + chan->op_fn = rtn; + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_set_opfn); + +int s3c2410_dma_set_buffdone_fn(dmach_t channel, s3c2410_dma_cbfn_t rtn) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: chan=%p, callback rtn=%p\n", __FUNCTION__, chan, rtn); + + chan->callback_fn = rtn; + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn); + +/* s3c2410_dma_devconfig + * + * configure the dma source/destination hardware type and address + * + * source: S3C2410_DMASRC_HW: source is hardware + * S3C2410_DMASRC_MEM: source is memory + * + * hwcfg: the value for xxxSTCn register, + * bit 0: 0=increment pointer, 1=leave pointer + * bit 1: 0=soucre is AHB, 1=soucre is APB + * + * devaddr: physical address of the source +*/ + +int s3c2410_dma_devconfig(int channel, + enum s3c2410_dmasrc source, + int hwcfg, + unsigned long devaddr) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + if (chan == NULL) + return -EINVAL; + + pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n", + __FUNCTION__, (int)source, hwcfg, devaddr); + + chan->source = source; + chan->dev_addr = devaddr; + + switch (source) { + case S3C2410_DMASRC_HW: + /* source is hardware */ + pr_debug("%s: hw source, devaddr=%08lx, hwcfg=%d\n", + __FUNCTION__, devaddr, hwcfg); + dma_wrreg(chan, S3C2410_DMA_DISRCC, hwcfg & 3); + dma_wrreg(chan, S3C2410_DMA_DISRC, devaddr); + dma_wrreg(chan, S3C2410_DMA_DIDSTC, (0<<1) | (0<<0)); + + chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DIDST); + return 0; + + case S3C2410_DMASRC_MEM: + /* source is memory */ + pr_debug( "%s: mem source, devaddr=%08lx, hwcfg=%d\n", + __FUNCTION__, devaddr, hwcfg); + dma_wrreg(chan, S3C2410_DMA_DISRCC, (0<<1) | (0<<0)); + dma_wrreg(chan, S3C2410_DMA_DIDST, devaddr); + dma_wrreg(chan, S3C2410_DMA_DIDSTC, hwcfg & 3); + + chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DISRC); + return 0; + } + + printk(KERN_ERR "dma%d: invalid source type (%d)\n", channel, source); + return -EINVAL; +} + +EXPORT_SYMBOL(s3c2410_dma_devconfig); + +/* s3c2410_dma_getposition + * + * returns the current transfer points for the dma source and destination +*/ + +int s3c2410_dma_getposition(dmach_t channel, dma_addr_t *src, dma_addr_t *dst) +{ + struct s3c2410_dma_chan *chan = lookup_dma_channel(channel); + + if (chan == NULL) + return -EINVAL; + + if (src != NULL) + *src = dma_rdreg(chan, S3C2410_DMA_DCSRC); + + if (dst != NULL) + *dst = dma_rdreg(chan, S3C2410_DMA_DCDST); + + return 0; +} + +EXPORT_SYMBOL(s3c2410_dma_getposition); + + +/* system device class */ + +#ifdef CONFIG_PM + +static int s3c2410_dma_suspend(struct sys_device *dev, pm_message_t state) +{ + struct s3c2410_dma_chan *cp = container_of(dev, struct s3c2410_dma_chan, dev); + + printk(KERN_DEBUG "suspending dma channel %d\n", cp->number); + + if (dma_rdreg(cp, S3C2410_DMA_DMASKTRIG) & S3C2410_DMASKTRIG_ON) { + /* the dma channel is still working, which is probably + * a bad thing to do over suspend/resume. We stop the + * channel and assume that the client is either going to + * retry after resume, or that it is broken. + */ + + printk(KERN_INFO "dma: stopping channel %d due to suspend\n", + cp->number); + + s3c2410_dma_dostop(cp); + } + + return 0; +} + +static int s3c2410_dma_resume(struct sys_device *dev) +{ + return 0; +} + +#else +#define s3c2410_dma_suspend NULL +#define s3c2410_dma_resume NULL +#endif /* CONFIG_PM */ + +struct sysdev_class dma_sysclass = { + set_kset_name("s3c24xx-dma"), + .suspend = s3c2410_dma_suspend, + .resume = s3c2410_dma_resume, +}; + +/* kmem cache implementation */ + +static void s3c2410_dma_cache_ctor(void *p, struct kmem_cache *c, unsigned long f) +{ + memset(p, 0, sizeof(struct s3c2410_dma_buf)); +} + +/* initialisation code */ + +static int __init s3c2410_init_dma(void) +{ + struct s3c2410_dma_chan *cp; + int channel; + int ret; + + printk("S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics\n"); + + dma_base = ioremap(S3C24XX_PA_DMA, 0x200); + if (dma_base == NULL) { + printk(KERN_ERR "dma failed to remap register block\n"); + return -ENOMEM; + } + + printk("Registering sysclass\n"); + + ret = sysdev_class_register(&dma_sysclass); + if (ret != 0) { + printk(KERN_ERR "dma sysclass registration failed\n"); + goto err; + } + + dma_kmem = kmem_cache_create("dma_desc", sizeof(struct s3c2410_dma_buf), 0, + SLAB_HWCACHE_ALIGN, + s3c2410_dma_cache_ctor, NULL); + + if (dma_kmem == NULL) { + printk(KERN_ERR "dma failed to make kmem cache\n"); + ret = -ENOMEM; + goto err; + } + + for (channel = 0; channel < S3C2410_DMA_CHANNELS; channel++) { + cp = &s3c2410_chans[channel]; + + memset(cp, 0, sizeof(struct s3c2410_dma_chan)); + + /* dma channel irqs are in order.. */ + cp->number = channel; + cp->irq = channel + IRQ_DMA0; + cp->regs = dma_base + (channel*0x40); + + /* point current stats somewhere */ + cp->stats = &cp->stats_store; + cp->stats_store.timeout_shortest = LONG_MAX; + + /* basic channel configuration */ + + cp->load_timeout = 1<<18; + + /* register system device */ + + cp->dev.cls = &dma_sysclass; + cp->dev.id = channel; + ret = sysdev_register(&cp->dev); + + printk("DMA channel %d at %p, irq %d\n", + cp->number, cp->regs, cp->irq); + } + + return 0; + + err: + kmem_cache_destroy(dma_kmem); + iounmap(dma_base); + dma_base = NULL; + return ret; +} + +core_initcall(s3c2410_init_dma); + +static inline int is_channel_valid(unsigned int channel) +{ + return (channel & DMA_CH_VALID); +} + +/* s3c2410_dma_map_channel() + * + * turn the virtual channel number into a real, and un-used hardware + * channel. + * + * currently this code uses first-free channel from the specified harware + * map, not taking into account anything that the board setup code may + * have to say about the likely peripheral set to be in use. +*/ + +struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) +{ + struct s3c24xx_dma_map *ch_map; + struct s3c2410_dma_chan *dmach; + int ch; + + if (dma_sel.map == NULL || channel > dma_sel.map_size) + return NULL; + + ch_map = dma_sel.map + channel; + + for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) { + if (!is_channel_valid(ch_map->channels[ch])) + continue; + + if (s3c2410_chans[ch].in_use == 0) { + printk("mapped channel %d to %d\n", channel, ch); + break; + } + } + + if (ch >= S3C2410_DMA_CHANNELS) + return NULL; + + /* update our channel mapping */ + + dmach = &s3c2410_chans[ch]; + dma_chan_map[channel] = dmach; + + /* select the channel */ + + (dma_sel.select)(dmach, ch_map); + + return dmach; +} + +static void s3c24xx_dma_show_ch(struct s3c24xx_dma_map *map, int ch) +{ + /* show the channel configuration */ + + printk("%2d: %20s, channels %c%c%c%c\n", ch, map->name, + (is_channel_valid(map->channels[0]) ? '0' : '-'), + (is_channel_valid(map->channels[1]) ? '1' : '-'), + (is_channel_valid(map->channels[2]) ? '2' : '-'), + (is_channel_valid(map->channels[3]) ? '3' : '-')); +} + +static int s3c24xx_dma_check_entry(struct s3c24xx_dma_map *map, int ch) +{ + if (1) + s3c24xx_dma_show_ch(map, ch); + + return 0; +} + +int __init s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel) +{ + struct s3c24xx_dma_map *nmap; + size_t map_sz = sizeof(*nmap) * sel->map_size; + int ptr; + + nmap = kmalloc(map_sz, GFP_KERNEL); + if (nmap == NULL) + return -ENOMEM; + + memcpy(nmap, sel->map, map_sz); + memcpy(&dma_sel, sel, sizeof(*sel)); + + dma_sel.map = nmap; + + for (ptr = 0; ptr < sel->map_size; ptr++) + s3c24xx_dma_check_entry(nmap+ptr, ptr); + + return 0; +} diff --git a/arch/arm/plat-s3c24xx/gpio.c b/arch/arm/plat-s3c24xx/gpio.c new file mode 100644 index 000000000000..ec3a09c4d181 --- /dev/null +++ b/arch/arm/plat-s3c24xx/gpio.c @@ -0,0 +1,188 @@ +/* linux/arch/arm/plat-s3c24xx/gpio.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * S3C24XX GPIO support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + + +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function) +{ + void __iomem *base = S3C24XX_GPIO_BASE(pin); + unsigned long mask; + unsigned long con; + unsigned long flags; + + if (pin < S3C2410_GPIO_BANKB) { + mask = 1 << S3C2410_GPIO_OFFSET(pin); + } else { + mask = 3 << S3C2410_GPIO_OFFSET(pin)*2; + } + + switch (function) { + case S3C2410_GPIO_LEAVE: + mask = 0; + function = 0; + break; + + case S3C2410_GPIO_INPUT: + case S3C2410_GPIO_OUTPUT: + case S3C2410_GPIO_SFN2: + case S3C2410_GPIO_SFN3: + if (pin < S3C2410_GPIO_BANKB) { + function -= 1; + function &= 1; + function <<= S3C2410_GPIO_OFFSET(pin); + } else { + function &= 3; + function <<= S3C2410_GPIO_OFFSET(pin)*2; + } + } + + /* modify the specified register wwith IRQs off */ + + local_irq_save(flags); + + con = __raw_readl(base + 0x00); + con &= ~mask; + con |= function; + + __raw_writel(con, base + 0x00); + + local_irq_restore(flags); +} + +EXPORT_SYMBOL(s3c2410_gpio_cfgpin); + +unsigned int s3c2410_gpio_getcfg(unsigned int pin) +{ + void __iomem *base = S3C24XX_GPIO_BASE(pin); + unsigned long val = __raw_readl(base); + + if (pin < S3C2410_GPIO_BANKB) { + val >>= S3C2410_GPIO_OFFSET(pin); + val &= 1; + val += 1; + } else { + val >>= S3C2410_GPIO_OFFSET(pin)*2; + val &= 3; + } + + return val | S3C2410_GPIO_INPUT; +} + +EXPORT_SYMBOL(s3c2410_gpio_getcfg); + +void s3c2410_gpio_pullup(unsigned int pin, unsigned int to) +{ + void __iomem *base = S3C24XX_GPIO_BASE(pin); + unsigned long offs = S3C2410_GPIO_OFFSET(pin); + unsigned long flags; + unsigned long up; + + if (pin < S3C2410_GPIO_BANKB) + return; + + local_irq_save(flags); + + up = __raw_readl(base + 0x08); + up &= ~(1L << offs); + up |= to << offs; + __raw_writel(up, base + 0x08); + + local_irq_restore(flags); +} + +EXPORT_SYMBOL(s3c2410_gpio_pullup); + +void s3c2410_gpio_setpin(unsigned int pin, unsigned int to) +{ + void __iomem *base = S3C24XX_GPIO_BASE(pin); + unsigned long offs = S3C2410_GPIO_OFFSET(pin); + unsigned long flags; + unsigned long dat; + + local_irq_save(flags); + + dat = __raw_readl(base + 0x04); + dat &= ~(1 << offs); + dat |= to << offs; + __raw_writel(dat, base + 0x04); + + local_irq_restore(flags); +} + +EXPORT_SYMBOL(s3c2410_gpio_setpin); + +unsigned int s3c2410_gpio_getpin(unsigned int pin) +{ + void __iomem *base = S3C24XX_GPIO_BASE(pin); + unsigned long offs = S3C2410_GPIO_OFFSET(pin); + + return __raw_readl(base + 0x04) & (1<< offs); +} + +EXPORT_SYMBOL(s3c2410_gpio_getpin); + +unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change) +{ + unsigned long flags; + unsigned long misccr; + + local_irq_save(flags); + misccr = __raw_readl(S3C24XX_MISCCR); + misccr &= ~clear; + misccr ^= change; + __raw_writel(misccr, S3C24XX_MISCCR); + local_irq_restore(flags); + + return misccr; +} + +EXPORT_SYMBOL(s3c2410_modify_misccr); + +int s3c2410_gpio_getirq(unsigned int pin) +{ + if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15) + return -1; /* not valid interrupts */ + + if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7) + return -1; /* not valid pin */ + + if (pin < S3C2410_GPF4) + return (pin - S3C2410_GPF0) + IRQ_EINT0; + + if (pin < S3C2410_GPG0) + return (pin - S3C2410_GPF4) + IRQ_EINT4; + + return (pin - S3C2410_GPG0) + IRQ_EINT8; +} + +EXPORT_SYMBOL(s3c2410_gpio_getirq); diff --git a/arch/arm/plat-s3c24xx/irq.c b/arch/arm/plat-s3c24xx/irq.c new file mode 100644 index 000000000000..ce186398e3fd --- /dev/null +++ b/arch/arm/plat-s3c24xx/irq.c @@ -0,0 +1,801 @@ +/* linux/arch/arm/plat-s3c24xx/irq.c + * + * Copyright (c) 2003,2004 Simtec Electronics + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Changelog: + * + * 22-Jul-2004 Ben Dooks + * Fixed compile warnings + * + * 22-Jul-2004 Roc Wu + * Fixed s3c_extirq_type + * + * 21-Jul-2004 Arnaud Patard (Rtp) + * Addition of ADC/TC demux + * + * 04-Oct-2004 Klaus Fetscher + * Fix for set_irq_type() on low EINT numbers + * + * 05-Oct-2004 Ben Dooks + * Tidy up KF's patch and sort out new release + * + * 05-Oct-2004 Ben Dooks + * Add support for power management controls + * + * 04-Nov-2004 Ben Dooks + * Fix standard IRQ wake for EINT0..4 and RTC + * + * 22-Feb-2005 Ben Dooks + * Fixed edge-triggering on ADC IRQ + * + * 28-Jun-2005 Ben Dooks + * Mark IRQ_LCD valid + * + * 25-Jul-2005 Ben Dooks + * Split the S3C2440 IRQ code to seperate file +*/ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include + +#include +#include +#include + +/* wakeup irq control */ + +#ifdef CONFIG_PM + +/* state for IRQs over sleep */ + +/* default is to allow for EINT0..EINT15, and IRQ_RTC as wakeup sources + * + * set bit to 1 in allow bitfield to enable the wakeup settings on it +*/ + +unsigned long s3c_irqwake_intallow = 1L << (IRQ_RTC - IRQ_EINT0) | 0xfL; +unsigned long s3c_irqwake_intmask = 0xffffffffL; +unsigned long s3c_irqwake_eintallow = 0x0000fff0L; +unsigned long s3c_irqwake_eintmask = 0xffffffffL; + +int +s3c_irq_wake(unsigned int irqno, unsigned int state) +{ + unsigned long irqbit = 1 << (irqno - IRQ_EINT0); + + if (!(s3c_irqwake_intallow & irqbit)) + return -ENOENT; + + printk(KERN_INFO "wake %s for irq %d\n", + state ? "enabled" : "disabled", irqno); + + if (!state) + s3c_irqwake_intmask |= irqbit; + else + s3c_irqwake_intmask &= ~irqbit; + + return 0; +} + +static int +s3c_irqext_wake(unsigned int irqno, unsigned int state) +{ + unsigned long bit = 1L << (irqno - EXTINT_OFF); + + if (!(s3c_irqwake_eintallow & bit)) + return -ENOENT; + + printk(KERN_INFO "wake %s for irq %d\n", + state ? "enabled" : "disabled", irqno); + + if (!state) + s3c_irqwake_eintmask |= bit; + else + s3c_irqwake_eintmask &= ~bit; + + return 0; +} + +#else +#define s3c_irqext_wake NULL +#define s3c_irq_wake NULL +#endif + + +static void +s3c_irq_mask(unsigned int irqno) +{ + unsigned long mask; + + irqno -= IRQ_EINT0; + + mask = __raw_readl(S3C2410_INTMSK); + mask |= 1UL << irqno; + __raw_writel(mask, S3C2410_INTMSK); +} + +static inline void +s3c_irq_ack(unsigned int irqno) +{ + unsigned long bitval = 1UL << (irqno - IRQ_EINT0); + + __raw_writel(bitval, S3C2410_SRCPND); + __raw_writel(bitval, S3C2410_INTPND); +} + +static inline void +s3c_irq_maskack(unsigned int irqno) +{ + unsigned long bitval = 1UL << (irqno - IRQ_EINT0); + unsigned long mask; + + mask = __raw_readl(S3C2410_INTMSK); + __raw_writel(mask|bitval, S3C2410_INTMSK); + + __raw_writel(bitval, S3C2410_SRCPND); + __raw_writel(bitval, S3C2410_INTPND); +} + + +static void +s3c_irq_unmask(unsigned int irqno) +{ + unsigned long mask; + + if (irqno != IRQ_TIMER4 && irqno != IRQ_EINT8t23) + irqdbf2("s3c_irq_unmask %d\n", irqno); + + irqno -= IRQ_EINT0; + + mask = __raw_readl(S3C2410_INTMSK); + mask &= ~(1UL << irqno); + __raw_writel(mask, S3C2410_INTMSK); +} + +struct irq_chip s3c_irq_level_chip = { + .name = "s3c-level", + .ack = s3c_irq_maskack, + .mask = s3c_irq_mask, + .unmask = s3c_irq_unmask, + .set_wake = s3c_irq_wake +}; + +static struct irq_chip s3c_irq_chip = { + .name = "s3c", + .ack = s3c_irq_ack, + .mask = s3c_irq_mask, + .unmask = s3c_irq_unmask, + .set_wake = s3c_irq_wake +}; + +static void +s3c_irqext_mask(unsigned int irqno) +{ + unsigned long mask; + + irqno -= EXTINT_OFF; + + mask = __raw_readl(S3C24XX_EINTMASK); + mask |= ( 1UL << irqno); + __raw_writel(mask, S3C24XX_EINTMASK); +} + +static void +s3c_irqext_ack(unsigned int irqno) +{ + unsigned long req; + unsigned long bit; + unsigned long mask; + + bit = 1UL << (irqno - EXTINT_OFF); + + mask = __raw_readl(S3C24XX_EINTMASK); + + __raw_writel(bit, S3C24XX_EINTPEND); + + req = __raw_readl(S3C24XX_EINTPEND); + req &= ~mask; + + /* not sure if we should be acking the parent irq... */ + + if (irqno <= IRQ_EINT7 ) { + if ((req & 0xf0) == 0) + s3c_irq_ack(IRQ_EINT4t7); + } else { + if ((req >> 8) == 0) + s3c_irq_ack(IRQ_EINT8t23); + } +} + +static void +s3c_irqext_unmask(unsigned int irqno) +{ + unsigned long mask; + + irqno -= EXTINT_OFF; + + mask = __raw_readl(S3C24XX_EINTMASK); + mask &= ~( 1UL << irqno); + __raw_writel(mask, S3C24XX_EINTMASK); +} + +int +s3c_irqext_type(unsigned int irq, unsigned int type) +{ + void __iomem *extint_reg; + void __iomem *gpcon_reg; + unsigned long gpcon_offset, extint_offset; + unsigned long newvalue = 0, value; + + if ((irq >= IRQ_EINT0) && (irq <= IRQ_EINT3)) + { + gpcon_reg = S3C2410_GPFCON; + extint_reg = S3C24XX_EXTINT0; + gpcon_offset = (irq - IRQ_EINT0) * 2; + extint_offset = (irq - IRQ_EINT0) * 4; + } + else if ((irq >= IRQ_EINT4) && (irq <= IRQ_EINT7)) + { + gpcon_reg = S3C2410_GPFCON; + extint_reg = S3C24XX_EXTINT0; + gpcon_offset = (irq - (EXTINT_OFF)) * 2; + extint_offset = (irq - (EXTINT_OFF)) * 4; + } + else if ((irq >= IRQ_EINT8) && (irq <= IRQ_EINT15)) + { + gpcon_reg = S3C2410_GPGCON; + extint_reg = S3C24XX_EXTINT1; + gpcon_offset = (irq - IRQ_EINT8) * 2; + extint_offset = (irq - IRQ_EINT8) * 4; + } + else if ((irq >= IRQ_EINT16) && (irq <= IRQ_EINT23)) + { + gpcon_reg = S3C2410_GPGCON; + extint_reg = S3C24XX_EXTINT2; + gpcon_offset = (irq - IRQ_EINT8) * 2; + extint_offset = (irq - IRQ_EINT16) * 4; + } else + return -1; + + /* Set the GPIO to external interrupt mode */ + value = __raw_readl(gpcon_reg); + value = (value & ~(3 << gpcon_offset)) | (0x02 << gpcon_offset); + __raw_writel(value, gpcon_reg); + + /* Set the external interrupt to pointed trigger type */ + switch (type) + { + case IRQT_NOEDGE: + printk(KERN_WARNING "No edge setting!\n"); + break; + + case IRQT_RISING: + newvalue = S3C2410_EXTINT_RISEEDGE; + break; + + case IRQT_FALLING: + newvalue = S3C2410_EXTINT_FALLEDGE; + break; + + case IRQT_BOTHEDGE: + newvalue = S3C2410_EXTINT_BOTHEDGE; + break; + + case IRQT_LOW: + newvalue = S3C2410_EXTINT_LOWLEV; + break; + + case IRQT_HIGH: + newvalue = S3C2410_EXTINT_HILEV; + break; + + default: + printk(KERN_ERR "No such irq type %d", type); + return -1; + } + + value = __raw_readl(extint_reg); + value = (value & ~(7 << extint_offset)) | (newvalue << extint_offset); + __raw_writel(value, extint_reg); + + return 0; +} + +static struct irq_chip s3c_irqext_chip = { + .name = "s3c-ext", + .mask = s3c_irqext_mask, + .unmask = s3c_irqext_unmask, + .ack = s3c_irqext_ack, + .set_type = s3c_irqext_type, + .set_wake = s3c_irqext_wake +}; + +static struct irq_chip s3c_irq_eint0t4 = { + .name = "s3c-ext0", + .ack = s3c_irq_ack, + .mask = s3c_irq_mask, + .unmask = s3c_irq_unmask, + .set_wake = s3c_irq_wake, + .set_type = s3c_irqext_type, +}; + +/* mask values for the parent registers for each of the interrupt types */ + +#define INTMSK_UART0 (1UL << (IRQ_UART0 - IRQ_EINT0)) +#define INTMSK_UART1 (1UL << (IRQ_UART1 - IRQ_EINT0)) +#define INTMSK_UART2 (1UL << (IRQ_UART2 - IRQ_EINT0)) +#define INTMSK_ADCPARENT (1UL << (IRQ_ADCPARENT - IRQ_EINT0)) + + +/* UART0 */ + +static void +s3c_irq_uart0_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_UART0, 7); +} + +static void +s3c_irq_uart0_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_UART0); +} + +static void +s3c_irq_uart0_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_UART0, 7); +} + +static struct irq_chip s3c_irq_uart0 = { + .name = "s3c-uart0", + .mask = s3c_irq_uart0_mask, + .unmask = s3c_irq_uart0_unmask, + .ack = s3c_irq_uart0_ack, +}; + +/* UART1 */ + +static void +s3c_irq_uart1_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_UART1, 7 << 3); +} + +static void +s3c_irq_uart1_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_UART1); +} + +static void +s3c_irq_uart1_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_UART1, 7 << 3); +} + +static struct irq_chip s3c_irq_uart1 = { + .name = "s3c-uart1", + .mask = s3c_irq_uart1_mask, + .unmask = s3c_irq_uart1_unmask, + .ack = s3c_irq_uart1_ack, +}; + +/* UART2 */ + +static void +s3c_irq_uart2_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_UART2, 7 << 6); +} + +static void +s3c_irq_uart2_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_UART2); +} + +static void +s3c_irq_uart2_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_UART2, 7 << 6); +} + +static struct irq_chip s3c_irq_uart2 = { + .name = "s3c-uart2", + .mask = s3c_irq_uart2_mask, + .unmask = s3c_irq_uart2_unmask, + .ack = s3c_irq_uart2_ack, +}; + +/* ADC and Touchscreen */ + +static void +s3c_irq_adc_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_ADCPARENT, 3 << 9); +} + +static void +s3c_irq_adc_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_ADCPARENT); +} + +static void +s3c_irq_adc_ack(unsigned int irqno) +{ + s3c_irqsub_ack(irqno, INTMSK_ADCPARENT, 3 << 9); +} + +static struct irq_chip s3c_irq_adc = { + .name = "s3c-adc", + .mask = s3c_irq_adc_mask, + .unmask = s3c_irq_adc_unmask, + .ack = s3c_irq_adc_ack, +}; + +/* irq demux for adc */ +static void s3c_irq_demux_adc(unsigned int irq, + struct irq_desc *desc) +{ + unsigned int subsrc, submsk; + unsigned int offset = 9; + struct irq_desc *mydesc; + + /* read the current pending interrupts, and the mask + * for what it is available */ + + subsrc = __raw_readl(S3C2410_SUBSRCPND); + submsk = __raw_readl(S3C2410_INTSUBMSK); + + subsrc &= ~submsk; + subsrc >>= offset; + subsrc &= 3; + + if (subsrc != 0) { + if (subsrc & 1) { + mydesc = irq_desc + IRQ_TC; + desc_handle_irq(IRQ_TC, mydesc); + } + if (subsrc & 2) { + mydesc = irq_desc + IRQ_ADC; + desc_handle_irq(IRQ_ADC, mydesc); + } + } +} + +static void s3c_irq_demux_uart(unsigned int start) +{ + unsigned int subsrc, submsk; + unsigned int offset = start - IRQ_S3CUART_RX0; + struct irq_desc *desc; + + /* read the current pending interrupts, and the mask + * for what it is available */ + + subsrc = __raw_readl(S3C2410_SUBSRCPND); + submsk = __raw_readl(S3C2410_INTSUBMSK); + + irqdbf2("s3c_irq_demux_uart: start=%d (%d), subsrc=0x%08x,0x%08x\n", + start, offset, subsrc, submsk); + + subsrc &= ~submsk; + subsrc >>= offset; + subsrc &= 7; + + if (subsrc != 0) { + desc = irq_desc + start; + + if (subsrc & 1) + desc_handle_irq(start, desc); + + desc++; + + if (subsrc & 2) + desc_handle_irq(start+1, desc); + + desc++; + + if (subsrc & 4) + desc_handle_irq(start+2, desc); + } +} + +/* uart demux entry points */ + +static void +s3c_irq_demux_uart0(unsigned int irq, + struct irq_desc *desc) +{ + irq = irq; + s3c_irq_demux_uart(IRQ_S3CUART_RX0); +} + +static void +s3c_irq_demux_uart1(unsigned int irq, + struct irq_desc *desc) +{ + irq = irq; + s3c_irq_demux_uart(IRQ_S3CUART_RX1); +} + +static void +s3c_irq_demux_uart2(unsigned int irq, + struct irq_desc *desc) +{ + irq = irq; + s3c_irq_demux_uart(IRQ_S3CUART_RX2); +} + +static void +s3c_irq_demux_extint8(unsigned int irq, + struct irq_desc *desc) +{ + unsigned long eintpnd = __raw_readl(S3C24XX_EINTPEND); + unsigned long eintmsk = __raw_readl(S3C24XX_EINTMASK); + + eintpnd &= ~eintmsk; + eintpnd &= ~0xff; /* ignore lower irqs */ + + /* we may as well handle all the pending IRQs here */ + + while (eintpnd) { + irq = __ffs(eintpnd); + eintpnd &= ~(1< + * + * http://armlinux.simtec.co.uk/ + * + * Power Management helpers for Simtec S3C24XX implementations + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#include +#include + +#include +#include +#include + +#include + +#include + +#define COPYRIGHT ", (c) 2005 Simtec Electronics" + +/* pm_simtec_init + * + * enable the power management functions +*/ + +static __init int pm_simtec_init(void) +{ + unsigned long gstatus4; + + /* check which machine we are running on */ + + if (!machine_is_bast() && !machine_is_vr1000() && + !machine_is_anubis() && !machine_is_osiris() && + !machine_is_aml_m5900()) + return 0; + + printk(KERN_INFO "Simtec Board Power Manangement" COPYRIGHT "\n"); + + gstatus4 = (__raw_readl(S3C2410_BANKCON7) & 0x3) << 30; + gstatus4 |= (__raw_readl(S3C2410_BANKCON6) & 0x3) << 28; + gstatus4 |= (__raw_readl(S3C2410_BANKSIZE) & S3C2410_BANKSIZE_MASK); + + __raw_writel(gstatus4, S3C2410_GSTATUS4); + + return s3c2410_pm_init(); +} + +arch_initcall(pm_simtec_init); diff --git a/arch/arm/plat-s3c24xx/pm.c b/arch/arm/plat-s3c24xx/pm.c new file mode 100644 index 000000000000..ecf68d611904 --- /dev/null +++ b/arch/arm/plat-s3c24xx/pm.c @@ -0,0 +1,659 @@ +/* linux/arch/arm/plat-s3c24xx/pm.c + * + * Copyright (c) 2004,2006 Simtec Electronics + * Ben Dooks + * + * S3C24XX Power Manager (Suspend-To-RAM) support + * + * See Documentation/arm/Samsung-S3C24XX/Suspend.txt for more information + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Parts based on arch/arm/mach-pxa/pm.c + * + * Thanks to Dimitry Andric for debugging +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include + +#include + +#include + +/* for external use */ + +unsigned long s3c_pm_flags; + +#define PFX "s3c24xx-pm: " + +static struct sleep_save core_save[] = { + SAVE_ITEM(S3C2410_LOCKTIME), + SAVE_ITEM(S3C2410_CLKCON), + + /* we restore the timings here, with the proviso that the board + * brings the system up in an slower, or equal frequency setting + * to the original system. + * + * if we cannot guarantee this, then things are going to go very + * wrong here, as we modify the refresh and both pll settings. + */ + + SAVE_ITEM(S3C2410_BWSCON), + SAVE_ITEM(S3C2410_BANKCON0), + SAVE_ITEM(S3C2410_BANKCON1), + SAVE_ITEM(S3C2410_BANKCON2), + SAVE_ITEM(S3C2410_BANKCON3), + SAVE_ITEM(S3C2410_BANKCON4), + SAVE_ITEM(S3C2410_BANKCON5), + + SAVE_ITEM(S3C2410_CLKDIVN), + SAVE_ITEM(S3C2410_MPLLCON), + SAVE_ITEM(S3C2410_UPLLCON), + SAVE_ITEM(S3C2410_CLKSLOW), + SAVE_ITEM(S3C2410_REFRESH), +}; + +static struct sleep_save gpio_save[] = { + SAVE_ITEM(S3C2410_GPACON), + SAVE_ITEM(S3C2410_GPADAT), + + SAVE_ITEM(S3C2410_GPBCON), + SAVE_ITEM(S3C2410_GPBDAT), + SAVE_ITEM(S3C2410_GPBUP), + + SAVE_ITEM(S3C2410_GPCCON), + SAVE_ITEM(S3C2410_GPCDAT), + SAVE_ITEM(S3C2410_GPCUP), + + SAVE_ITEM(S3C2410_GPDCON), + SAVE_ITEM(S3C2410_GPDDAT), + SAVE_ITEM(S3C2410_GPDUP), + + SAVE_ITEM(S3C2410_GPECON), + SAVE_ITEM(S3C2410_GPEDAT), + SAVE_ITEM(S3C2410_GPEUP), + + SAVE_ITEM(S3C2410_GPFCON), + SAVE_ITEM(S3C2410_GPFDAT), + SAVE_ITEM(S3C2410_GPFUP), + + SAVE_ITEM(S3C2410_GPGCON), + SAVE_ITEM(S3C2410_GPGDAT), + SAVE_ITEM(S3C2410_GPGUP), + + SAVE_ITEM(S3C2410_GPHCON), + SAVE_ITEM(S3C2410_GPHDAT), + SAVE_ITEM(S3C2410_GPHUP), + + SAVE_ITEM(S3C2410_DCLKCON), +}; + +#ifdef CONFIG_S3C2410_PM_DEBUG + +#define SAVE_UART(va) \ + SAVE_ITEM((va) + S3C2410_ULCON), \ + SAVE_ITEM((va) + S3C2410_UCON), \ + SAVE_ITEM((va) + S3C2410_UFCON), \ + SAVE_ITEM((va) + S3C2410_UMCON), \ + SAVE_ITEM((va) + S3C2410_UBRDIV) + +static struct sleep_save uart_save[] = { + SAVE_UART(S3C24XX_VA_UART0), + SAVE_UART(S3C24XX_VA_UART1), +#ifndef CONFIG_CPU_S3C2400 + SAVE_UART(S3C24XX_VA_UART2), +#endif +}; + +/* debug + * + * we send the debug to printascii() to allow it to be seen if the + * system never wakes up from the sleep +*/ + +extern void printascii(const char *); + +void pm_dbg(const char *fmt, ...) +{ + va_list va; + char buff[256]; + + va_start(va, fmt); + vsprintf(buff, fmt, va); + va_end(va); + + printascii(buff); +} + +static void s3c2410_pm_debug_init(void) +{ + unsigned long tmp = __raw_readl(S3C2410_CLKCON); + + /* re-start uart clocks */ + tmp |= S3C2410_CLKCON_UART0; + tmp |= S3C2410_CLKCON_UART1; + tmp |= S3C2410_CLKCON_UART2; + + __raw_writel(tmp, S3C2410_CLKCON); + udelay(10); +} + +#define DBG(fmt...) pm_dbg(fmt) +#else +#define DBG(fmt...) printk(KERN_DEBUG fmt) + +#define s3c2410_pm_debug_init() do { } while(0) + +static struct sleep_save uart_save[] = {}; +#endif + +#if defined(CONFIG_S3C2410_PM_CHECK) && CONFIG_S3C2410_PM_CHECK_CHUNKSIZE != 0 + +/* suspend checking code... + * + * this next area does a set of crc checks over all the installed + * memory, so the system can verify if the resume was ok. + * + * CONFIG_S3C2410_PM_CHECK_CHUNKSIZE defines the block-size for the CRC, + * increasing it will mean that the area corrupted will be less easy to spot, + * and reducing the size will cause the CRC save area to grow +*/ + +#define CHECK_CHUNKSIZE (CONFIG_S3C2410_PM_CHECK_CHUNKSIZE * 1024) + +static u32 crc_size; /* size needed for the crc block */ +static u32 *crcs; /* allocated over suspend/resume */ + +typedef u32 *(run_fn_t)(struct resource *ptr, u32 *arg); + +/* s3c2410_pm_run_res + * + * go thorugh the given resource list, and look for system ram +*/ + +static void s3c2410_pm_run_res(struct resource *ptr, run_fn_t fn, u32 *arg) +{ + while (ptr != NULL) { + if (ptr->child != NULL) + s3c2410_pm_run_res(ptr->child, fn, arg); + + if ((ptr->flags & IORESOURCE_MEM) && + strcmp(ptr->name, "System RAM") == 0) { + DBG("Found system RAM at %08lx..%08lx\n", + ptr->start, ptr->end); + arg = (fn)(ptr, arg); + } + + ptr = ptr->sibling; + } +} + +static void s3c2410_pm_run_sysram(run_fn_t fn, u32 *arg) +{ + s3c2410_pm_run_res(&iomem_resource, fn, arg); +} + +static u32 *s3c2410_pm_countram(struct resource *res, u32 *val) +{ + u32 size = (u32)(res->end - res->start)+1; + + size += CHECK_CHUNKSIZE-1; + size /= CHECK_CHUNKSIZE; + + DBG("Area %08lx..%08lx, %d blocks\n", res->start, res->end, size); + + *val += size * sizeof(u32); + return val; +} + +/* s3c2410_pm_prepare_check + * + * prepare the necessary information for creating the CRCs. This + * must be done before the final save, as it will require memory + * allocating, and thus touching bits of the kernel we do not + * know about. +*/ + +static void s3c2410_pm_check_prepare(void) +{ + crc_size = 0; + + s3c2410_pm_run_sysram(s3c2410_pm_countram, &crc_size); + + DBG("s3c2410_pm_prepare_check: %u checks needed\n", crc_size); + + crcs = kmalloc(crc_size+4, GFP_KERNEL); + if (crcs == NULL) + printk(KERN_ERR "Cannot allocated CRC save area\n"); +} + +static u32 *s3c2410_pm_makecheck(struct resource *res, u32 *val) +{ + unsigned long addr, left; + + for (addr = res->start; addr < res->end; + addr += CHECK_CHUNKSIZE) { + left = res->end - addr; + + if (left > CHECK_CHUNKSIZE) + left = CHECK_CHUNKSIZE; + + *val = crc32_le(~0, phys_to_virt(addr), left); + val++; + } + + return val; +} + +/* s3c2410_pm_check_store + * + * compute the CRC values for the memory blocks before the final + * sleep. +*/ + +static void s3c2410_pm_check_store(void) +{ + if (crcs != NULL) + s3c2410_pm_run_sysram(s3c2410_pm_makecheck, crcs); +} + +/* in_region + * + * return TRUE if the area defined by ptr..ptr+size contatins the + * what..what+whatsz +*/ + +static inline int in_region(void *ptr, int size, void *what, size_t whatsz) +{ + if ((what+whatsz) < ptr) + return 0; + + if (what > (ptr+size)) + return 0; + + return 1; +} + +static u32 *s3c2410_pm_runcheck(struct resource *res, u32 *val) +{ + void *save_at = phys_to_virt(s3c2410_sleep_save_phys); + unsigned long addr; + unsigned long left; + void *ptr; + u32 calc; + + for (addr = res->start; addr < res->end; + addr += CHECK_CHUNKSIZE) { + left = res->end - addr; + + if (left > CHECK_CHUNKSIZE) + left = CHECK_CHUNKSIZE; + + ptr = phys_to_virt(addr); + + if (in_region(ptr, left, crcs, crc_size)) { + DBG("skipping %08lx, has crc block in\n", addr); + goto skip_check; + } + + if (in_region(ptr, left, save_at, 32*4 )) { + DBG("skipping %08lx, has save block in\n", addr); + goto skip_check; + } + + /* calculate and check the checksum */ + + calc = crc32_le(~0, ptr, left); + if (calc != *val) { + printk(KERN_ERR PFX "Restore CRC error at " + "%08lx (%08x vs %08x)\n", addr, calc, *val); + + DBG("Restore CRC error at %08lx (%08x vs %08x)\n", + addr, calc, *val); + } + + skip_check: + val++; + } + + return val; +} + +/* s3c2410_pm_check_restore + * + * check the CRCs after the restore event and free the memory used + * to hold them +*/ + +static void s3c2410_pm_check_restore(void) +{ + if (crcs != NULL) { + s3c2410_pm_run_sysram(s3c2410_pm_runcheck, crcs); + kfree(crcs); + crcs = NULL; + } +} + +#else + +#define s3c2410_pm_check_prepare() do { } while(0) +#define s3c2410_pm_check_restore() do { } while(0) +#define s3c2410_pm_check_store() do { } while(0) +#endif + +/* helper functions to save and restore register state */ + +void s3c2410_pm_do_save(struct sleep_save *ptr, int count) +{ + for (; count > 0; count--, ptr++) { + ptr->val = __raw_readl(ptr->reg); + DBG("saved %p value %08lx\n", ptr->reg, ptr->val); + } +} + +/* s3c2410_pm_do_restore + * + * restore the system from the given list of saved registers + * + * Note, we do not use DBG() in here, as the system may not have + * restore the UARTs state yet +*/ + +void s3c2410_pm_do_restore(struct sleep_save *ptr, int count) +{ + for (; count > 0; count--, ptr++) { + printk(KERN_DEBUG "restore %p (restore %08lx, was %08x)\n", + ptr->reg, ptr->val, __raw_readl(ptr->reg)); + + __raw_writel(ptr->val, ptr->reg); + } +} + +/* s3c2410_pm_do_restore_core + * + * similar to s3c2410_pm_do_restore_core + * + * WARNING: Do not put any debug in here that may effect memory or use + * peripherals, as things may be changing! +*/ + +static void s3c2410_pm_do_restore_core(struct sleep_save *ptr, int count) +{ + for (; count > 0; count--, ptr++) { + __raw_writel(ptr->val, ptr->reg); + } +} + +/* s3c2410_pm_show_resume_irqs + * + * print any IRQs asserted at resume time (ie, we woke from) +*/ + +static void s3c2410_pm_show_resume_irqs(int start, unsigned long which, + unsigned long mask) +{ + int i; + + which &= ~mask; + + for (i = 0; i <= 31; i++) { + if ((which) & (1L< + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * +*/ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include + +#include +#include +#include + +/* camera irq */ + +static void s3c_irq_demux_cam(unsigned int irq, + struct irq_desc *desc) +{ + unsigned int subsrc, submsk; + struct irq_desc *mydesc; + + /* read the current pending interrupts, and the mask + * for what it is available */ + + subsrc = __raw_readl(S3C2410_SUBSRCPND); + submsk = __raw_readl(S3C2410_INTSUBMSK); + + subsrc &= ~submsk; + subsrc >>= 11; + subsrc &= 3; + + if (subsrc != 0) { + if (subsrc & 1) { + mydesc = irq_desc + IRQ_S3C2440_CAM_C; + desc_handle_irq(IRQ_S3C2440_CAM_C, mydesc); + } + if (subsrc & 2) { + mydesc = irq_desc + IRQ_S3C2440_CAM_P; + desc_handle_irq(IRQ_S3C2440_CAM_P, mydesc); + } + } +} + +#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0)) + +static void +s3c_irq_cam_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_CAM, 3<<11); +} + +static void +s3c_irq_cam_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_CAM); +} + +static void +s3c_irq_cam_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_CAM, 3<<11); +} + +static struct irq_chip s3c_irq_cam = { + .mask = s3c_irq_cam_mask, + .unmask = s3c_irq_cam_unmask, + .ack = s3c_irq_cam_ack, +}; + +static int s3c244x_irq_add(struct sys_device *sysdev) +{ + unsigned int irqno; + + set_irq_chip(IRQ_NFCON, &s3c_irq_level_chip); + set_irq_handler(IRQ_NFCON, handle_level_irq); + set_irq_flags(IRQ_NFCON, IRQF_VALID); + + /* add chained handler for camera */ + + set_irq_chip(IRQ_CAM, &s3c_irq_level_chip); + set_irq_handler(IRQ_CAM, handle_level_irq); + set_irq_chained_handler(IRQ_CAM, s3c_irq_demux_cam); + + for (irqno = IRQ_S3C2440_CAM_C; irqno <= IRQ_S3C2440_CAM_P; irqno++) { + set_irq_chip(irqno, &s3c_irq_cam); + set_irq_handler(irqno, handle_level_irq); + set_irq_flags(irqno, IRQF_VALID); + } + + return 0; +} + +static struct sysdev_driver s3c2440_irq_driver = { + .add = s3c244x_irq_add, + .suspend = s3c24xx_irq_suspend, + .resume = s3c24xx_irq_resume, +}; + +static int s3c2440_irq_init(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver); +} + +arch_initcall(s3c2440_irq_init); + +static struct sysdev_driver s3c2442_irq_driver = { + .add = s3c244x_irq_add, + .suspend = s3c24xx_irq_suspend, + .resume = s3c24xx_irq_resume, +}; + + +static int s3c2442_irq_init(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_irq_driver); +} + +arch_initcall(s3c2442_irq_init); diff --git a/arch/arm/plat-s3c24xx/s3c244x.c b/arch/arm/plat-s3c24xx/s3c244x.c new file mode 100644 index 000000000000..87aace4c8f8c --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c244x.c @@ -0,0 +1,184 @@ +/* linux/arch/arm/plat-s3c24xx/s3c244x.c + * + * Copyright (c) 2004-2006 Simtec Electronics + * Ben Dooks + * + * Samsung S3C2440 and S3C2442 Mobile CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include +#include "s3c244x.h" +#include +#include +#include +#include + +static struct map_desc s3c244x_iodesc[] __initdata = { + IODESC_ENT(CLKPWR), + IODESC_ENT(TIMER), + IODESC_ENT(WATCHDOG), + IODESC_ENT(LCD), +}; + +/* uart initialisation */ + +void __init s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no) +{ + s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no); +} + +void __init s3c244x_map_io(struct map_desc *mach_desc, int size) +{ + /* register our io-tables */ + + iotable_init(s3c244x_iodesc, ARRAY_SIZE(s3c244x_iodesc)); + iotable_init(mach_desc, size); + + /* rename any peripherals used differing from the s3c2410 */ + + s3c_device_i2c.name = "s3c2440-i2c"; + s3c_device_nand.name = "s3c2440-nand"; + s3c_device_usbgadget.name = "s3c2440-usbgadget"; +} + +void __init s3c244x_init_clocks(int xtal) +{ + unsigned long clkdiv; + unsigned long camdiv; + unsigned long hclk, fclk, pclk; + int hdiv = 1; + + /* now we've got our machine bits initialised, work out what + * clocks we've got */ + + fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2; + + clkdiv = __raw_readl(S3C2410_CLKDIVN); + camdiv = __raw_readl(S3C2440_CAMDIVN); + + /* work out clock scalings */ + + switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) { + case S3C2440_CLKDIVN_HDIVN_1: + hdiv = 1; + break; + + case S3C2440_CLKDIVN_HDIVN_2: + hdiv = 2; + break; + + case S3C2440_CLKDIVN_HDIVN_4_8: + hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4; + break; + + case S3C2440_CLKDIVN_HDIVN_3_6: + hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3; + break; + } + + hclk = fclk / hdiv; + pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1); + + /* print brief summary of clocks, etc */ + + printk("S3C244X: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", + print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); + + /* initialise the clocks here, to allow other things like the + * console to use them, and to add new ones after the initialisation + */ + + s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); + s3c2410_baseclk_add(); +} + +#ifdef CONFIG_PM + +static struct sleep_save s3c244x_sleep[] = { + SAVE_ITEM(S3C2440_DSC0), + SAVE_ITEM(S3C2440_DSC1), + SAVE_ITEM(S3C2440_GPJDAT), + SAVE_ITEM(S3C2440_GPJCON), + SAVE_ITEM(S3C2440_GPJUP) +}; + +static int s3c244x_suspend(struct sys_device *dev, pm_message_t state) +{ + s3c2410_pm_do_save(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep)); + return 0; +} + +static int s3c244x_resume(struct sys_device *dev) +{ + s3c2410_pm_do_restore(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep)); + return 0; +} + +#else +#define s3c244x_suspend NULL +#define s3c244x_resume NULL +#endif + +/* Since the S3C2442 and S3C2440 share items, put both sysclasses here */ + +struct sysdev_class s3c2440_sysclass = { + set_kset_name("s3c2440-core"), + .suspend = s3c244x_suspend, + .resume = s3c244x_resume +}; + +struct sysdev_class s3c2442_sysclass = { + set_kset_name("s3c2442-core"), + .suspend = s3c244x_suspend, + .resume = s3c244x_resume +}; + +/* need to register class before we actually register the device, and + * we also need to ensure that it has been initialised before any of the + * drivers even try to use it (even if not on an s3c2440 based system) + * as a driver which may support both 2410 and 2440 may try and use it. +*/ + +static int __init s3c2440_core_init(void) +{ + return sysdev_class_register(&s3c2440_sysclass); +} + +core_initcall(s3c2440_core_init); + +static int __init s3c2442_core_init(void) +{ + return sysdev_class_register(&s3c2442_sysclass); +} + +core_initcall(s3c2442_core_init); diff --git a/arch/arm/plat-s3c24xx/s3c244x.h b/arch/arm/plat-s3c24xx/s3c244x.h new file mode 100644 index 000000000000..f8ed17676a35 --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c244x.h @@ -0,0 +1,25 @@ +/* linux/arch/arm/plat-s3c24xx/s3c244x.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Header file for S3C2440 and S3C2442 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) + +extern void s3c244x_map_io(struct map_desc *mach_desc, int size); + +extern void s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c244x_init_clocks(int xtal); + +#else +#define s3c244x_init_clocks NULL +#define s3c244x_init_uarts NULL +#define s3c244x_map_io NULL +#endif diff --git a/arch/arm/plat-s3c24xx/sleep.S b/arch/arm/plat-s3c24xx/sleep.S new file mode 100644 index 000000000000..2018c2e1dcc5 --- /dev/null +++ b/arch/arm/plat-s3c24xx/sleep.S @@ -0,0 +1,159 @@ +/* linux/arch/arm/mach-s3c2410/sleep.S + * + * Copyright (c) 2004 Simtec Electronics + * Ben Dooks + * + * S3C2410 Power Manager (Suspend-To-RAM) support + * + * Based on PXA/SA1100 sleep code by: + * Nicolas Pitre, (c) 2002 Monta Vista Software Inc + * Cliff Brake, (c) 2001 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include + +#include +#include +#include +#include + +/* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not + * reset the UART configuration, only enable if you really need this! +*/ +//#define CONFIG_DEBUG_RESUME + + .text + + /* s3c2410_cpu_save + * + * save enough of the CPU state to allow us to re-start + * pm.c code. as we store items like the sp/lr, we will + * end up returning from this function when the cpu resumes + * so the return value is set to mark this. + * + * This arangement means we avoid having to flush the cache + * from this code. + * + * entry: + * r0 = pointer to save block + * + * exit: + * r0 = 0 => we stored everything + * 1 => resumed from sleep + */ + +ENTRY(s3c2410_cpu_save) + stmfd sp!, { r4 - r12, lr } + + @@ store co-processor registers + + mrc p15, 0, r4, c15, c1, 0 @ CP access register + mrc p15, 0, r5, c13, c0, 0 @ PID + mrc p15, 0, r6, c3, c0, 0 @ Domain ID + mrc p15, 0, r7, c2, c0, 0 @ translation table base address + mrc p15, 0, r8, c1, c0, 0 @ control register + + stmia r0, { r4 - r13 } + + mov r0, #0 + ldmfd sp, { r4 - r12, pc } + + @@ return to the caller, after having the MMU + @@ turned on, this restores the last bits from the + @@ stack +resume_with_mmu: + mov r0, #1 + ldmfd sp!, { r4 - r12, pc } + + .ltorg + + @@ the next bits sit in the .data segment, even though they + @@ happen to be code... the s3c2410_sleep_save_phys needs to be + @@ accessed by the resume code before it can restore the MMU. + @@ This means that the variable has to be close enough for the + @@ code to read it... since the .text segment needs to be RO, + @@ the data segment can be the only place to put this code. + + .data + + .global s3c2410_sleep_save_phys +s3c2410_sleep_save_phys: + .word 0 + + /* s3c2410_cpu_resume + * + * resume code entry for bootloader to call + * + * we must put this code here in the data segment as we have no + * other way of restoring the stack pointer after sleep, and we + * must not write to the code segment (code is read-only) + */ + +ENTRY(s3c2410_cpu_resume) + mov r0, #PSR_I_BIT | PSR_F_BIT | SVC_MODE + msr cpsr_c, r0 + + @@ load UART to allow us to print the two characters for + @@ resume debug + + mov r2, #S3C24XX_PA_UART & 0xff000000 + orr r2, r2, #S3C24XX_PA_UART & 0xff000 + +#if 0 + /* SMDK2440 LED set */ + mov r14, #S3C24XX_PA_GPIO + ldr r12, [ r14, #0x54 ] + bic r12, r12, #3<<4 + orr r12, r12, #1<<7 + str r12, [ r14, #0x54 ] +#endif + +#ifdef CONFIG_DEBUG_RESUME + mov r3, #'L' + strb r3, [ r2, #S3C2410_UTXH ] +1001: + ldrb r14, [ r3, #S3C2410_UTRSTAT ] + tst r14, #S3C2410_UTRSTAT_TXE + beq 1001b +#endif /* CONFIG_DEBUG_RESUME */ + + mov r1, #0 + mcr p15, 0, r1, c8, c7, 0 @@ invalidate I & D TLBs + mcr p15, 0, r1, c7, c7, 0 @@ invalidate I & D caches + + ldr r0, s3c2410_sleep_save_phys @ address of restore block + ldmia r0, { r4 - r13 } + + mcr p15, 0, r4, c15, c1, 0 @ CP access register + mcr p15, 0, r5, c13, c0, 0 @ PID + mcr p15, 0, r6, c3, c0, 0 @ Domain ID + mcr p15, 0, r7, c2, c0, 0 @ translation table base + +#ifdef CONFIG_DEBUG_RESUME + mov r3, #'R' + strb r3, [ r2, #S3C2410_UTXH ] +#endif + + ldr r2, =resume_with_mmu + mcr p15, 0, r8, c1, c0, 0 @ turn on MMU, etc + nop @ second-to-last before mmu + mov pc, r2 @ go back to virtual address + + .ltorg diff --git a/arch/arm/plat-s3c24xx/time.c b/arch/arm/plat-s3c24xx/time.c new file mode 100644 index 000000000000..c523d1c9cce5 --- /dev/null +++ b/arch/arm/plat-s3c24xx/time.c @@ -0,0 +1,262 @@ +/* linux/arch/arm/plat-s3c24xx/time.c + * + * Copyright (C) 2003-2005 Simtec Electronics + * Ben Dooks, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include + +static unsigned long timer_startval; +static unsigned long timer_usec_ticks; + +#define TIMER_USEC_SHIFT 16 + +/* we use the shifted arithmetic to work out the ratio of timer ticks + * to usecs, as often the peripheral clock is not a nice even multiple + * of 1MHz. + * + * shift of 14 and 15 are too low for the 12MHz, 16 seems to be ok + * for the current HZ value of 200 without producing overflows. + * + * Original patch by Dimitry Andric, updated by Ben Dooks +*/ + + +/* timer_mask_usec_ticks + * + * given a clock and divisor, make the value to pass into timer_ticks_to_usec + * to scale the ticks into usecs +*/ + +static inline unsigned long +timer_mask_usec_ticks(unsigned long scaler, unsigned long pclk) +{ + unsigned long den = pclk / 1000; + + return ((1000 << TIMER_USEC_SHIFT) * scaler + (den >> 1)) / den; +} + +/* timer_ticks_to_usec + * + * convert timer ticks to usec. +*/ + +static inline unsigned long timer_ticks_to_usec(unsigned long ticks) +{ + unsigned long res; + + res = ticks * timer_usec_ticks; + res += 1 << (TIMER_USEC_SHIFT - 4); /* round up slightly */ + + return res >> TIMER_USEC_SHIFT; +} + +/*** + * Returns microsecond since last clock interrupt. Note that interrupts + * will have been disabled by do_gettimeoffset() + * IRQs are disabled before entering here from do_gettimeofday() + */ + +#define SRCPND_TIMER4 (1<<(IRQ_TIMER4 - IRQ_EINT0)) + +static unsigned long s3c2410_gettimeoffset (void) +{ + unsigned long tdone; + unsigned long irqpend; + unsigned long tval; + + /* work out how many ticks have gone since last timer interrupt */ + + tval = __raw_readl(S3C2410_TCNTO(4)); + tdone = timer_startval - tval; + + /* check to see if there is an interrupt pending */ + + irqpend = __raw_readl(S3C2410_SRCPND); + if (irqpend & SRCPND_TIMER4) { + /* re-read the timer, and try and fix up for the missed + * interrupt. Note, the interrupt may go off before the + * timer has re-loaded from wrapping. + */ + + tval = __raw_readl(S3C2410_TCNTO(4)); + tdone = timer_startval - tval; + + if (tval != 0) + tdone += timer_startval; + } + + return timer_ticks_to_usec(tdone); +} + + +/* + * IRQ handler for the timer + */ +static irqreturn_t +s3c2410_timer_interrupt(int irq, void *dev_id) +{ + write_seqlock(&xtime_lock); + timer_tick(); + write_sequnlock(&xtime_lock); + return IRQ_HANDLED; +} + +static struct irqaction s3c2410_timer_irq = { + .name = "S3C2410 Timer Tick", + .flags = IRQF_DISABLED | IRQF_TIMER, + .handler = s3c2410_timer_interrupt, +}; + +#define use_tclk1_12() ( \ + machine_is_bast() || \ + machine_is_vr1000() || \ + machine_is_anubis() || \ + machine_is_osiris() ) + +/* + * Set up timer interrupt, and return the current time in seconds. + * + * Currently we only use timer4, as it is the only timer which has no + * other function that can be exploited externally + */ +static void s3c2410_timer_setup (void) +{ + unsigned long tcon; + unsigned long tcnt; + unsigned long tcfg1; + unsigned long tcfg0; + + tcnt = 0xffff; /* default value for tcnt */ + + /* read the current timer configuration bits */ + + tcon = __raw_readl(S3C2410_TCON); + tcfg1 = __raw_readl(S3C2410_TCFG1); + tcfg0 = __raw_readl(S3C2410_TCFG0); + + /* configure the system for whichever machine is in use */ + + if (use_tclk1_12()) { + /* timer is at 12MHz, scaler is 1 */ + timer_usec_ticks = timer_mask_usec_ticks(1, 12000000); + tcnt = 12000000 / HZ; + + tcfg1 &= ~S3C2410_TCFG1_MUX4_MASK; + tcfg1 |= S3C2410_TCFG1_MUX4_TCLK1; + } else { + unsigned long pclk; + struct clk *clk; + + /* for the h1940 (and others), we use the pclk from the core + * to generate the timer values. since values around 50 to + * 70MHz are not values we can directly generate the timer + * value from, we need to pre-scale and divide before using it. + * + * for instance, using 50.7MHz and dividing by 6 gives 8.45MHz + * (8.45 ticks per usec) + */ + + /* this is used as default if no other timer can be found */ + + clk = clk_get(NULL, "timers"); + if (IS_ERR(clk)) + panic("failed to get clock for system timer"); + + clk_enable(clk); + + pclk = clk_get_rate(clk); + + /* configure clock tick */ + + timer_usec_ticks = timer_mask_usec_ticks(6, pclk); + + tcfg1 &= ~S3C2410_TCFG1_MUX4_MASK; + tcfg1 |= S3C2410_TCFG1_MUX4_DIV2; + + tcfg0 &= ~S3C2410_TCFG_PRESCALER1_MASK; + tcfg0 |= ((6 - 1) / 2) << S3C2410_TCFG_PRESCALER1_SHIFT; + + tcnt = (pclk / 6) / HZ; + } + + /* timers reload after counting zero, so reduce the count by 1 */ + + tcnt--; + + printk("timer tcon=%08lx, tcnt %04lx, tcfg %08lx,%08lx, usec %08lx\n", + tcon, tcnt, tcfg0, tcfg1, timer_usec_ticks); + + /* check to see if timer is within 16bit range... */ + if (tcnt > 0xffff) { + panic("setup_timer: HZ is too small, cannot configure timer!"); + return; + } + + __raw_writel(tcfg1, S3C2410_TCFG1); + __raw_writel(tcfg0, S3C2410_TCFG0); + + timer_startval = tcnt; + __raw_writel(tcnt, S3C2410_TCNTB(4)); + + /* ensure timer is stopped... */ + + tcon &= ~(7<<20); + tcon |= S3C2410_TCON_T4RELOAD; + tcon |= S3C2410_TCON_T4MANUALUPD; + + __raw_writel(tcon, S3C2410_TCON); + __raw_writel(tcnt, S3C2410_TCNTB(4)); + __raw_writel(tcnt, S3C2410_TCMPB(4)); + + /* start the timer running */ + tcon |= S3C2410_TCON_T4START; + tcon &= ~S3C2410_TCON_T4MANUALUPD; + __raw_writel(tcon, S3C2410_TCON); +} + +static void __init s3c2410_timer_init (void) +{ + s3c2410_timer_setup(); + setup_irq(IRQ_TIMER4, &s3c2410_timer_irq); +} + +struct sys_timer s3c24xx_timer = { + .init = s3c2410_timer_init, + .offset = s3c2410_gettimeoffset, + .resume = s3c2410_timer_setup +}; diff --git a/include/asm-arm/plat-s3c24xx/clock.h b/include/asm-arm/plat-s3c24xx/clock.h new file mode 100644 index 000000000000..f6135dbb9fa9 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/clock.h @@ -0,0 +1,63 @@ +/* linux/include/asm-arm/plat-s3c24xx/clock.h + * linux/arch/arm/mach-s3c2410/clock.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * http://www.simtec.co.uk/products/SWLINUX/ + * Written by Ben Dooks, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +struct clk { + struct list_head list; + struct module *owner; + struct clk *parent; + const char *name; + int id; + int usage; + unsigned long rate; + unsigned long ctrlbit; + + int (*enable)(struct clk *, int enable); + int (*set_rate)(struct clk *c, unsigned long rate); + unsigned long (*get_rate)(struct clk *c); + unsigned long (*round_rate)(struct clk *c, unsigned long rate); + int (*set_parent)(struct clk *c, struct clk *parent); +}; + +/* other clocks which may be registered by board support */ + +extern struct clk s3c24xx_dclk0; +extern struct clk s3c24xx_dclk1; +extern struct clk s3c24xx_clkout0; +extern struct clk s3c24xx_clkout1; +extern struct clk s3c24xx_uclk; + +extern struct clk clk_usb_bus; + +/* core clock support */ + +extern struct clk clk_f; +extern struct clk clk_h; +extern struct clk clk_p; +extern struct clk clk_mpll; +extern struct clk clk_upll; +extern struct clk clk_xtal; + +/* exports for arch/arm/mach-s3c2410 + * + * Please DO NOT use these outside of arch/arm/mach-s3c2410 +*/ + +extern struct mutex clocks_mutex; + +extern int s3c2410_clkcon_enable(struct clk *clk, int enable); + +extern int s3c24xx_register_clock(struct clk *clk); + +extern int s3c24xx_setup_clocks(unsigned long xtal, + unsigned long fclk, + unsigned long hclk, + unsigned long pclk); diff --git a/include/asm-arm/plat-s3c24xx/common-smdk.h b/include/asm-arm/plat-s3c24xx/common-smdk.h new file mode 100644 index 000000000000..58d9094c935c --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/common-smdk.h @@ -0,0 +1,15 @@ +/* linux/include/asm-arm/plat-s3c24xx/common-smdk.h + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * Common code for SMDK2410 and SMDK2440 boards + * + * http://www.fluff.org/ben/smdk2440/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +extern void smdk_machine_init(void); diff --git a/include/asm-arm/plat-s3c24xx/cpu.h b/include/asm-arm/plat-s3c24xx/cpu.h new file mode 100644 index 000000000000..8181b22532bd --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/cpu.h @@ -0,0 +1,69 @@ +/* linux/include/asm-arm/plat-s3c24xx/cpu.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Header file for S3C24XX CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* todo - fix when rmk changes iodescs to use `void __iomem *` */ + +#define IODESC_ENT(x) { (unsigned long)S3C24XX_VA_##x, __phys_to_pfn(S3C24XX_PA_##x), S3C24XX_SZ_##x, MT_DEVICE } + +#ifndef MHZ +#define MHZ (1000*1000) +#endif + +#define print_mhz(m) ((m) / MHZ), ((m / 1000) % 1000) + +/* forward declaration */ +struct s3c24xx_uart_resources; +struct platform_device; +struct s3c2410_uartcfg; +struct map_desc; + +/* core initialisation functions */ + +extern void s3c24xx_init_irq(void); + +extern void s3c24xx_init_io(struct map_desc *mach_desc, int size); + +extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c24xx_init_clocks(int xtal); + +extern void s3c24xx_init_uartdevs(char *name, + struct s3c24xx_uart_resources *res, + struct s3c2410_uartcfg *cfg, int no); + +/* the board structure is used at first initialsation time + * to get info such as the devices to register for this + * board. This is done because platfrom_add_devices() cannot + * be called from the map_io entry. +*/ + +struct s3c24xx_board { + struct platform_device **devices; + unsigned int devices_count; + + struct clk **clocks; + unsigned int clocks_count; +}; + +extern void s3c24xx_set_board(struct s3c24xx_board *board); + +/* timer for 2410/2440 */ + +struct sys_timer; +extern struct sys_timer s3c24xx_timer; + +/* system device classes */ + +extern struct sysdev_class s3c2410_sysclass; +extern struct sysdev_class s3c2412_sysclass; +extern struct sysdev_class s3c2440_sysclass; +extern struct sysdev_class s3c2442_sysclass; diff --git a/include/asm-arm/plat-s3c24xx/devs.h b/include/asm-arm/plat-s3c24xx/devs.h new file mode 100644 index 000000000000..dddf485fc067 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/devs.h @@ -0,0 +1,51 @@ +/* linux/include/asm-arm/plat-s3c24xx/devs.h + * + * Copyright (c) 2004 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2410 standard platform devices + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ +#include + +struct s3c24xx_uart_resources { + struct resource *resources; + unsigned long nr_resources; +}; + +extern struct s3c24xx_uart_resources s3c2410_uart_resources[]; + +extern struct platform_device *s3c24xx_uart_devs[]; +extern struct platform_device *s3c24xx_uart_src[]; + +extern struct platform_device s3c_device_usb; +extern struct platform_device s3c_device_lcd; +extern struct platform_device s3c_device_wdt; +extern struct platform_device s3c_device_i2c; +extern struct platform_device s3c_device_iis; +extern struct platform_device s3c_device_rtc; +extern struct platform_device s3c_device_adc; +extern struct platform_device s3c_device_sdi; + +extern struct platform_device s3c_device_spi0; +extern struct platform_device s3c_device_spi1; + +extern struct platform_device s3c_device_nand; + +extern struct platform_device s3c_device_timer0; +extern struct platform_device s3c_device_timer1; +extern struct platform_device s3c_device_timer2; +extern struct platform_device s3c_device_timer3; + +extern struct platform_device s3c_device_usbgadget; + +/* s3c2440 specific devices */ + +#ifdef CONFIG_CPU_S3C2440 + +extern struct platform_device s3c_device_camif; + +#endif diff --git a/include/asm-arm/plat-s3c24xx/dma.h b/include/asm-arm/plat-s3c24xx/dma.h new file mode 100644 index 000000000000..421b567fa019 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/dma.h @@ -0,0 +1,45 @@ +/* linux/include/asm-arm/plat-s3c24xx/dma.h + * + * Copyright (C) 2006 Simtec Electronics + * Ben Dooks + * + * Samsung S3C24XX DMA support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +extern struct sysdev_class dma_sysclass; +extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; + +#define DMA_CH_VALID (1<<31) + +struct s3c24xx_dma_addr { + unsigned long from; + unsigned long to; +}; + +/* struct s3c24xx_dma_map + * + * this holds the mapping information for the channel selected + * to be connected to the specified device +*/ + +struct s3c24xx_dma_map { + const char *name; + struct s3c24xx_dma_addr hw_addr; + + unsigned long channels[S3C2410_DMA_CHANNELS]; +}; + +struct s3c24xx_dma_selection { + struct s3c24xx_dma_map *map; + unsigned long map_size; + unsigned long dcon_mask; + + void (*select)(struct s3c2410_dma_chan *chan, + struct s3c24xx_dma_map *map); +}; + +extern int s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel); diff --git a/include/asm-arm/plat-s3c24xx/irq.h b/include/asm-arm/plat-s3c24xx/irq.h new file mode 100644 index 000000000000..8af6d9579b31 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/irq.h @@ -0,0 +1,107 @@ +/* linux/include/asm-arm/plat-s3c24xx/irq.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Header file for S3C24XX CPU IRQ support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define irqdbf(x...) +#define irqdbf2(x...) + +#define EXTINT_OFF (IRQ_EINT4 - 4) + +extern struct irq_chip s3c_irq_level_chip; + +static inline void +s3c_irqsub_mask(unsigned int irqno, unsigned int parentbit, + int subcheck) +{ + unsigned long mask; + unsigned long submask; + + submask = __raw_readl(S3C2410_INTSUBMSK); + mask = __raw_readl(S3C2410_INTMSK); + + submask |= (1UL << (irqno - IRQ_S3CUART_RX0)); + + /* check to see if we need to mask the parent IRQ */ + + if ((submask & subcheck) == subcheck) { + __raw_writel(mask | parentbit, S3C2410_INTMSK); + } + + /* write back masks */ + __raw_writel(submask, S3C2410_INTSUBMSK); + +} + +static inline void +s3c_irqsub_unmask(unsigned int irqno, unsigned int parentbit) +{ + unsigned long mask; + unsigned long submask; + + submask = __raw_readl(S3C2410_INTSUBMSK); + mask = __raw_readl(S3C2410_INTMSK); + + submask &= ~(1UL << (irqno - IRQ_S3CUART_RX0)); + mask &= ~parentbit; + + /* write back masks */ + __raw_writel(submask, S3C2410_INTSUBMSK); + __raw_writel(mask, S3C2410_INTMSK); +} + + +static inline void +s3c_irqsub_maskack(unsigned int irqno, unsigned int parentmask, unsigned int group) +{ + unsigned int bit = 1UL << (irqno - IRQ_S3CUART_RX0); + + s3c_irqsub_mask(irqno, parentmask, group); + + __raw_writel(bit, S3C2410_SUBSRCPND); + + /* only ack parent if we've got all the irqs (seems we must + * ack, all and hope that the irq system retriggers ok when + * the interrupt goes off again) + */ + + if (1) { + __raw_writel(parentmask, S3C2410_SRCPND); + __raw_writel(parentmask, S3C2410_INTPND); + } +} + +static inline void +s3c_irqsub_ack(unsigned int irqno, unsigned int parentmask, unsigned int group) +{ + unsigned int bit = 1UL << (irqno - IRQ_S3CUART_RX0); + + __raw_writel(bit, S3C2410_SUBSRCPND); + + /* only ack parent if we've got all the irqs (seems we must + * ack, all and hope that the irq system retriggers ok when + * the interrupt goes off again) + */ + + if (1) { + __raw_writel(parentmask, S3C2410_SRCPND); + __raw_writel(parentmask, S3C2410_INTPND); + } +} + +/* exported for use in arch/arm/mach-s3c2410 */ + +#ifdef CONFIG_PM +extern int s3c_irq_wake(unsigned int irqno, unsigned int state); +#else +#define s3c_irq_wake NULL +#endif + +extern int s3c_irqext_type(unsigned int irq, unsigned int type); diff --git a/include/asm-arm/plat-s3c24xx/pm.h b/include/asm-arm/plat-s3c24xx/pm.h new file mode 100644 index 000000000000..cc623667e48a --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/pm.h @@ -0,0 +1,73 @@ +/* linux/include/asm-arm/plat-s3c24xx/pm.h + * + * Copyright (c) 2004 Simtec Electronics + * Written by Ben Dooks, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* s3c2410_pm_init + * + * called from board at initialisation time to setup the power + * management +*/ + +#ifdef CONFIG_PM + +extern __init int s3c2410_pm_init(void); + +#else + +static inline int s3c2410_pm_init(void) +{ + return 0; +} +#endif + +/* configuration for the IRQ mask over sleep */ +extern unsigned long s3c_irqwake_intmask; +extern unsigned long s3c_irqwake_eintmask; + +/* IRQ masks for IRQs allowed to go to sleep (see irq.c) */ +extern unsigned long s3c_irqwake_intallow; +extern unsigned long s3c_irqwake_eintallow; + +/* per-cpu sleep functions */ + +extern void (*pm_cpu_prep)(void); +extern void (*pm_cpu_sleep)(void); + +/* Flags for PM Control */ + +extern unsigned long s3c_pm_flags; + +/* from sleep.S */ + +extern int s3c2410_cpu_save(unsigned long *saveblk); +extern void s3c2410_cpu_suspend(void); +extern void s3c2410_cpu_resume(void); + +extern unsigned long s3c2410_sleep_save_phys; + +/* sleep save info */ + +struct sleep_save { + void __iomem *reg; + unsigned long val; +}; + +#define SAVE_ITEM(x) \ + { .reg = (x) } + +extern void s3c2410_pm_do_save(struct sleep_save *ptr, int count); +extern void s3c2410_pm_do_restore(struct sleep_save *ptr, int count); + +#ifdef CONFIG_PM +extern int s3c24xx_irq_suspend(struct sys_device *dev, pm_message_t state); +extern int s3c24xx_irq_resume(struct sys_device *dev); +#else +#define s3c24xx_irq_suspend NULL +#define s3c24xx_irq_resume NULL +#endif diff --git a/include/asm-arm/plat-s3c24xx/s3c2400.h b/include/asm-arm/plat-s3c24xx/s3c2400.h new file mode 100644 index 000000000000..3a5a16821af8 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/s3c2400.h @@ -0,0 +1,31 @@ +/* linux/include/asm-arm/plat-s3c24xx/s3c2400.h + * + * Copyright (c) 2004 Simtec Electronics + * Ben Dooks + * + * Header file for S3C2400 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Modifications: + * 09-Fev-2006 LCVR First version, based on s3c2410.h +*/ + +#ifdef CONFIG_CPU_S3C2400 + +extern int s3c2400_init(void); + +extern void s3c2400_map_io(struct map_desc *mach_desc, int size); + +extern void s3c2400_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c2400_init_clocks(int xtal); + +#else +#define s3c2400_init_clocks NULL +#define s3c2400_init_uarts NULL +#define s3c2400_map_io NULL +#define s3c2400_init NULL +#endif diff --git a/include/asm-arm/plat-s3c24xx/s3c2410.h b/include/asm-arm/plat-s3c24xx/s3c2410.h new file mode 100644 index 000000000000..36de0b835873 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/s3c2410.h @@ -0,0 +1,31 @@ +/* linux/include/asm-arm/plat-s3c24xx/s3c2410.h + * + * Copyright (c) 2004 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2410 machine directory + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#ifdef CONFIG_CPU_S3C2410 + +extern int s3c2410_init(void); + +extern void s3c2410_map_io(struct map_desc *mach_desc, int size); + +extern void s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c2410_init_clocks(int xtal); + +extern int s3c2410_baseclk_add(void); + +#else +#define s3c2410_init_clocks NULL +#define s3c2410_init_uarts NULL +#define s3c2410_map_io NULL +#define s3c2410_init NULL +#endif diff --git a/include/asm-arm/plat-s3c24xx/s3c2412.h b/include/asm-arm/plat-s3c24xx/s3c2412.h new file mode 100644 index 000000000000..3ec97685e781 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/s3c2412.h @@ -0,0 +1,29 @@ +/* linux/include/asm-arm/plat-s3c24xx/s3c2412.h + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2412 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifdef CONFIG_CPU_S3C2412 + +extern int s3c2412_init(void); + +extern void s3c2412_map_io(struct map_desc *mach_desc, int size); + +extern void s3c2412_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c2412_init_clocks(int xtal); + +extern int s3c2412_baseclk_add(void); +#else +#define s3c2412_init_clocks NULL +#define s3c2412_init_uarts NULL +#define s3c2412_map_io NULL +#define s3c2412_init NULL +#endif diff --git a/include/asm-arm/plat-s3c24xx/s3c2440.h b/include/asm-arm/plat-s3c24xx/s3c2440.h new file mode 100644 index 000000000000..107853bf9481 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/s3c2440.h @@ -0,0 +1,17 @@ +/* linux/include/asm-arm/plat-s3c24xx/s3c2440.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2440 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifdef CONFIG_CPU_S3C2440 +extern int s3c2440_init(void); +#else +#define s3c2440_init NULL +#endif diff --git a/include/asm-arm/plat-s3c24xx/s3c2442.h b/include/asm-arm/plat-s3c24xx/s3c2442.h new file mode 100644 index 000000000000..451a23a2092a --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/s3c2442.h @@ -0,0 +1,17 @@ +/* linux/include/asm-arm/plat-s3c24xx/s3c2442.h + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2442 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifdef CONFIG_CPU_S3C2442 +extern int s3c2442_init(void); +#else +#define s3c2442_init NULL +#endif -- cgit v1.2.3 From 1b8fc1880cf36bd1f3df932601a6745bb164acc4 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sun, 11 Feb 2007 18:56:03 +0100 Subject: [ARM] 4159/1: S3C2410: fix compile of arch/arm/mach-s3c2410/mach-aml5900.c Fix compile of arch/arm/mach-s3c2410/mach-aml5900.c due to missing fixes that have been applied to the rest of the tree. Include to provide the upf_t type needed for the serial code, and remove the old static map of the SPI which is not needed for the new spi drivers. mach-amlm5900.c:51: include/asm/arch/regs-serial.h:200: error: parse error befo re "upf_t" mach-amlm5900.c:117: error: 'S3C24XX_VA_SPI' undeclared here (not in a function) Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/mach-amlm5900.c | 8 +------- 1 file changed, 1 insertion(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c index d54cda1b3006..72f2cc4fcd03 100644 --- a/arch/arm/mach-s3c2410/mach-amlm5900.c +++ b/arch/arm/mach-s3c2410/mach-amlm5900.c @@ -35,7 +35,7 @@ #include #include #include - +#include #include #include @@ -113,12 +113,6 @@ static struct platform_device amlm5900_device_nor = { #endif static struct map_desc amlm5900_iodesc[] __initdata = { - { - .virtual = (u32)S3C24XX_VA_SPI, - .pfn = __phys_to_pfn(S3C2410_PA_SPI), - .length = SZ_1M, - .type = MT_DEVICE - } }; #define UCON S3C2410_UCON_DEFAULT -- cgit v1.2.3 From 90ac7648e0bcbf84a33aed5b15ae6894fda92779 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sun, 11 Feb 2007 18:58:58 +0100 Subject: [ARM] 4160/1: S3C24XX: defconfig update for 2.6.20 Update defconfig for the 2.6.20 release, and ensure that the AML5900 machine is built. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/configs/s3c2410_defconfig | 57 ++++++++++++++++++++++++++------------ 1 file changed, 40 insertions(+), 17 deletions(-) (limited to 'arch') diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index 3b31a33d0080..dd685f90202f 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.19-rc4 -# Fri Nov 3 17:41:31 2006 +# Linux kernel version: 2.6.20 +# Sun Feb 11 17:46:02 2007 # CONFIG_ARM=y # CONFIG_GENERIC_TIME is not set @@ -11,6 +11,8 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_VECTORS_BASE=0xffff0000 @@ -37,13 +39,14 @@ CONFIG_SYSVIPC=y # CONFIG_UTS_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set +CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y -# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set @@ -76,7 +79,9 @@ CONFIG_KMOD=y # Block layer # CONFIG_BLOCK=y +# CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set # # IO Schedulers @@ -110,6 +115,7 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_IMX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_IXP2000 is not set # CONFIG_ARCH_IXP23XX is not set @@ -126,11 +132,12 @@ CONFIG_ARCH_S3C2410=y # # S3C24XX Implementations # -# CONFIG_MACH_AML_M5900 is not set +CONFIG_MACH_AML_M5900=y CONFIG_MACH_ANUBIS=y CONFIG_MACH_OSIRIS=y CONFIG_ARCH_BAST=y CONFIG_BAST_PC104_IRQ=y +CONFIG_PM_H1940=y CONFIG_ARCH_H1940=y CONFIG_MACH_N30=y CONFIG_MACH_SMDK=y @@ -303,6 +310,7 @@ CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set # CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set @@ -385,6 +393,7 @@ CONFIG_MTD_CMDLINE_PARTS=y # User Modules And Translation Layers # CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set # CONFIG_NFTL is not set @@ -530,6 +539,11 @@ CONFIG_BLK_DEV_IDE_BAST=y # CONFIG_SCSI is not set # CONFIG_SCSI_NETLINK is not set +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +# CONFIG_ATA is not set + # # Multi-device support (RAID and LVM) # @@ -682,7 +696,7 @@ CONFIG_SERIAL_NONSTANDARD=y # CONFIG_DIGIEPCA is not set # CONFIG_MOXA_INTELLIO is not set # CONFIG_MOXA_SMARTIO is not set -# CONFIG_ISI is not set +# CONFIG_MOXA_SMARTIO_NEW is not set # CONFIG_SYNCLINKMP is not set # CONFIG_N_HDLC is not set # CONFIG_RISCOM8 is not set @@ -700,13 +714,14 @@ CONFIG_SERIAL_8250_NR_UARTS=8 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y -CONFIG_SERIAL_8250_SHARE_IRQ=y -# CONFIG_SERIAL_8250_DETECT_IRQ is not set -# CONFIG_SERIAL_8250_RSA is not set # CONFIG_SERIAL_8250_FOURPORT is not set # CONFIG_SERIAL_8250_ACCENT is not set # CONFIG_SERIAL_8250_BOCA is not set +# CONFIG_SERIAL_8250_EXAR_ST16C554 is not set # CONFIG_SERIAL_8250_HUB6 is not set +CONFIG_SERIAL_8250_SHARE_IRQ=y +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set # # Non-8250 serial port support @@ -755,10 +770,6 @@ CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set - -# -# Ftape, the floppy tape device driver -# # CONFIG_RAW_DRIVER is not set # @@ -863,6 +874,7 @@ CONFIG_SENSORS_LM85=m # CONFIG_SENSORS_LM92 is not set # CONFIG_SENSORS_MAX1619 is not set # CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_SMSC47M192 is not set # CONFIG_SENSORS_SMSC47B397 is not set @@ -870,6 +882,7 @@ CONFIG_SENSORS_LM85=m # CONFIG_SENSORS_W83781D is not set # CONFIG_SENSORS_W83791D is not set # CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set # CONFIG_SENSORS_W83L785TS is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set @@ -951,6 +964,11 @@ CONFIG_FONT_8x16=y # # CONFIG_SOUND is not set +# +# HID Devices +# +CONFIG_HID=y + # # USB support # @@ -1028,6 +1046,7 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set CONFIG_USB_MON=y @@ -1179,9 +1198,6 @@ CONFIG_RAMFS=y # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set -CONFIG_JFFS_FS=y -CONFIG_JFFS_FS_VERBOSE=0 -# CONFIG_JFFS_PROC_FS is not set CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y @@ -1284,6 +1300,11 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set +# +# Distributed Lock Manager +# +# CONFIG_DLM is not set + # # Profiling support # @@ -1296,6 +1317,8 @@ CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set CONFIG_DEBUG_KERNEL=y CONFIG_LOG_BUF_SHIFT=16 CONFIG_DETECT_SOFTLOCKUP=y @@ -1311,12 +1334,10 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y -# CONFIG_DEBUG_FS is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set CONFIG_FRAME_POINTER=y CONFIG_FORCED_INLINING=y -# CONFIG_HEADERS_CHECK is not set # CONFIG_RCU_TORTURE_TEST is not set CONFIG_DEBUG_USER=y # CONFIG_DEBUG_ERRORS is not set @@ -1339,6 +1360,7 @@ CONFIG_DEBUG_S3C2410_UART=0 # # Library routines # +CONFIG_BITREVERSE=y # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set CONFIG_CRC32=y @@ -1346,3 +1368,4 @@ CONFIG_CRC32=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_PLIST=y +CONFIG_IOMAP_COPY=y -- cgit v1.2.3 From b887060532b98d8c0f3a1c3169f06f55bb196bd8 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sun, 11 Feb 2007 20:33:13 +0100 Subject: [ARM] 4161/1: S3C24XX: fix leakage of plat-s3c24xx Kconfig items Do not export S3C24XX from plat-s3c24xx on non-s3c24xx systems Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/plat-s3c24xx/Kconfig | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig index 97813645b5ee..e22343160634 100644 --- a/arch/arm/plat-s3c24xx/Kconfig +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -7,10 +7,12 @@ config PLAT_S3C24XX bool depends on ARCH_S3C2410 - default y + default y if ARCH_S3C2410 help Base platform code for any Samsung S3C device +if PLAT_S3C24XX + config CPU_S3C244X bool depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442) @@ -94,3 +96,4 @@ config MACH_SMDK help Common machine code for SMDK2410 and SMDK2440 +endif -- cgit v1.2.3 From ab2c21529df6ee0f06787773882a1abc6bc2d665 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 12 Feb 2007 10:28:24 +0000 Subject: [ARM] Add a reference from struct device to the dma bounce info dmabounce keeps a per-device structure, and finds the correct structure by walking a list. Since architectures can now add fields to struct device, we can attach this structure direct to the struct device, thereby eliminating the code to search the list. Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 31 +++++++------------------------ include/asm-arm/device.h | 10 +++++++++- 2 files changed, 16 insertions(+), 25 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index 2e635b814c14..490e1fe286d5 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -66,8 +66,6 @@ struct dmabounce_pool { }; struct dmabounce_device_info { - struct list_head node; - struct device *dev; struct list_head safe_buffers; #ifdef STATS @@ -81,8 +79,6 @@ struct dmabounce_device_info { rwlock_t lock; }; -static LIST_HEAD(dmabounce_devs); - #ifdef STATS static void print_alloc_stats(struct dmabounce_device_info *device_info) { @@ -96,19 +92,6 @@ static void print_alloc_stats(struct dmabounce_device_info *device_info) } #endif -/* find the given device in the dmabounce device list */ -static inline struct dmabounce_device_info * -find_dmabounce_dev(struct device *dev) -{ - struct dmabounce_device_info *d; - - list_for_each_entry(d, &dmabounce_devs, node) - if (d->dev == dev) - return d; - - return NULL; -} - /* allocate a 'safe' buffer and keep track of it */ static inline struct safe_buffer * @@ -231,7 +214,7 @@ static inline dma_addr_t map_single(struct device *dev, void *ptr, size_t size, enum dma_data_direction dir) { - struct dmabounce_device_info *device_info = find_dmabounce_dev(dev); + struct dmabounce_device_info *device_info = dev->archdata.dmabounce; dma_addr_t dma_addr; int needs_bounce = 0; @@ -292,7 +275,7 @@ static inline void unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, enum dma_data_direction dir) { - struct dmabounce_device_info *device_info = find_dmabounce_dev(dev); + struct dmabounce_device_info *device_info = dev->archdata.dmabounce; struct safe_buffer *buf = NULL; /* @@ -343,7 +326,7 @@ static inline void sync_single(struct device *dev, dma_addr_t dma_addr, size_t size, enum dma_data_direction dir) { - struct dmabounce_device_info *device_info = find_dmabounce_dev(dev); + struct dmabounce_device_info *device_info = dev->archdata.dmabounce; struct safe_buffer *buf = NULL; if (device_info) @@ -606,7 +589,7 @@ dmabounce_register_dev(struct device *dev, unsigned long small_buffer_size, device_info->bounce_count = 0; #endif - list_add(&device_info->node, &dmabounce_devs); + dev->archdata.dmabounce = device_info; printk(KERN_INFO "dmabounce: registered device %s on %s bus\n", dev->bus_id, dev->bus->name); @@ -623,7 +606,9 @@ dmabounce_register_dev(struct device *dev, unsigned long small_buffer_size, void dmabounce_unregister_dev(struct device *dev) { - struct dmabounce_device_info *device_info = find_dmabounce_dev(dev); + struct dmabounce_device_info *device_info = dev->archdata.dmabounce; + + dev->archdata.dmabounce = NULL; if (!device_info) { printk(KERN_WARNING @@ -649,8 +634,6 @@ dmabounce_unregister_dev(struct device *dev) print_map_stats(device_info); #endif - list_del(&device_info->node); - kfree(device_info); printk(KERN_INFO "dmabounce: device %s on %s bus unregistered\n", diff --git a/include/asm-arm/device.h b/include/asm-arm/device.h index d8f9872b0e2d..c61642b40603 100644 --- a/include/asm-arm/device.h +++ b/include/asm-arm/device.h @@ -3,5 +3,13 @@ * * This file is released under the GPLv2 */ -#include +#ifndef ASMARM_DEVICE_H +#define ASMARM_DEVICE_H +struct dev_archdata { +#ifdef CONFIG_DMABOUNCE + struct dmabounce_device_info *dmabounce; +#endif +}; + +#endif -- cgit v1.2.3 From 017cc022b6f0a0619cc3b0bba43e1c3247b06779 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 12 Feb 2007 10:53:50 +0000 Subject: [ARM] Convert dmabounce statistics to use a device attribute Rather than printk'ing the dmabounce statistics occasionally to the kernel log, provide a sysfs file to allow this information to be periodically read. Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 35 +++++++++++++++-------------------- 1 file changed, 15 insertions(+), 20 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index 490e1fe286d5..4d5b031ac745 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -32,7 +32,6 @@ #include -#undef DEBUG #undef STATS #ifdef STATS @@ -72,6 +71,7 @@ struct dmabounce_device_info { unsigned long total_allocs; unsigned long map_op_count; unsigned long bounce_count; + int attr_res; #endif struct dmabounce_pool small; struct dmabounce_pool large; @@ -80,16 +80,21 @@ struct dmabounce_device_info { }; #ifdef STATS -static void print_alloc_stats(struct dmabounce_device_info *device_info) +static ssize_t dmabounce_show(struct device *dev, struct device_attribute *attr, + char *buf) { - printk(KERN_INFO - "%s: dmabounce: sbp: %lu, lbp: %lu, other: %lu, total: %lu\n", - device_info->dev->bus_id, - device_info->small.allocs, device_info->large.allocs, + struct dmabounce_device_info *device_info = dev->archdata.dmabounce; + return sprintf(buf, "%lu %lu %lu %lu %lu %lu\n", + device_info->small.allocs, + device_info->large.allocs, device_info->total_allocs - device_info->small.allocs - device_info->large.allocs, - device_info->total_allocs); + device_info->total_allocs, + device_info->map_op_count, + device_info->bounce_count); } + +static DEVICE_ATTR(dmabounce_stats, 0400, dmabounce_show, NULL); #endif @@ -145,8 +150,6 @@ alloc_safe_buffer(struct dmabounce_device_info *device_info, void *ptr, if (pool) pool->allocs++; device_info->total_allocs++; - if (device_info->total_allocs % 1000 == 0) - print_alloc_stats(device_info); #endif write_lock_irqsave(&device_info->lock, flags); @@ -201,15 +204,6 @@ free_safe_buffer(struct dmabounce_device_info *device_info, struct safe_buffer * /* ************************************************** */ -#ifdef STATS -static void print_map_stats(struct dmabounce_device_info *device_info) -{ - dev_info(device_info->dev, - "dmabounce: map_op_count=%lu, bounce_count=%lu\n", - device_info->map_op_count, device_info->bounce_count); -} -#endif - static inline dma_addr_t map_single(struct device *dev, void *ptr, size_t size, enum dma_data_direction dir) @@ -587,6 +581,7 @@ dmabounce_register_dev(struct device *dev, unsigned long small_buffer_size, device_info->total_allocs = 0; device_info->map_op_count = 0; device_info->bounce_count = 0; + device_info->attr_res = device_create_file(dev, &dev_attr_dmabounce_stats); #endif dev->archdata.dmabounce = device_info; @@ -630,8 +625,8 @@ dmabounce_unregister_dev(struct device *dev) dma_pool_destroy(device_info->large.pool); #ifdef STATS - print_alloc_stats(device_info); - print_map_stats(device_info); + if (device_info->attr_res == 0) + device_remove_file(dev, &dev_attr_dmabounce_stats); #endif kfree(device_info); -- cgit v1.2.3 From 72922bac1050f00fcd1dc3412fcfe71f8190f9c6 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 12 Feb 2007 14:38:26 +0100 Subject: [ARM] 4162/1: S3C24XX: update defconfig_s3c2410 after move Update the s3c2410_defconfig after the movement of arch/arm/mach-s3c2410 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/configs/s3c2410_defconfig | 85 ++++++++++++++++++++++---------------- 1 file changed, 49 insertions(+), 36 deletions(-) (limited to 'arch') diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index dd685f90202f..e8f9375764d6 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit # Linux kernel version: 2.6.20 -# Sun Feb 11 17:46:02 2007 +# Mon Feb 12 13:32:08 2007 # CONFIG_ARM=y # CONFIG_GENERIC_TIME is not set @@ -128,55 +128,67 @@ CONFIG_ARCH_S3C2410=y # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set # CONFIG_ARCH_OMAP is not set +CONFIG_PLAT_S3C24XX=y +CONFIG_CPU_S3C244X=y +CONFIG_PM_SIMTEC=y +# CONFIG_S3C2410_BOOT_WATCHDOG is not set +# CONFIG_S3C2410_BOOT_ERROR_RESET is not set +# CONFIG_S3C2410_PM_DEBUG is not set +# CONFIG_S3C2410_PM_CHECK is not set +CONFIG_S3C2410_LOWLEVEL_UART_PORT=0 +CONFIG_S3C2410_DMA=y +# CONFIG_S3C2410_DMA_DEBUG is not set +CONFIG_MACH_SMDK=y # -# S3C24XX Implementations +# S3C2400 Machines # -CONFIG_MACH_AML_M5900=y -CONFIG_MACH_ANUBIS=y -CONFIG_MACH_OSIRIS=y -CONFIG_ARCH_BAST=y -CONFIG_BAST_PC104_IRQ=y -CONFIG_PM_H1940=y +CONFIG_CPU_S3C2410=y +CONFIG_CPU_S3C2410_DMA=y +CONFIG_S3C2410_PM=y +CONFIG_S3C2410_GPIO=y +CONFIG_S3C2410_CLOCK=y + +# +# S3C2410 Machines +# +CONFIG_ARCH_SMDK2410=y CONFIG_ARCH_H1940=y +CONFIG_PM_H1940=y CONFIG_MACH_N30=y -CONFIG_MACH_SMDK=y -CONFIG_ARCH_SMDK2410=y -CONFIG_ARCH_S3C2440=y -CONFIG_SMDK2440_CPU2440=y -CONFIG_SMDK2440_CPU2442=y -CONFIG_MACH_S3C2413=y -CONFIG_MACH_SMDK2413=y -CONFIG_MACH_VR1000=y -CONFIG_MACH_RX3715=y +CONFIG_ARCH_BAST=y CONFIG_MACH_OTOM=y -CONFIG_MACH_NEXCODER_2440=y -CONFIG_MACH_VSTMS=y -CONFIG_S3C2410_CLOCK=y -CONFIG_S3C2410_PM=y -CONFIG_CPU_S3C2410_DMA=y -CONFIG_CPU_S3C2410=y -CONFIG_S3C2412_PM=y +CONFIG_MACH_AML_M5900=y +CONFIG_BAST_PC104_IRQ=y +CONFIG_MACH_VR1000=y CONFIG_CPU_S3C2412=y -CONFIG_CPU_S3C244X=y +CONFIG_S3C2412_DMA=y +CONFIG_S3C2412_PM=y + +# +# S3C2412 Machines +# +CONFIG_MACH_SMDK2413=y +CONFIG_MACH_S3C2413=y +CONFIG_MACH_VSTMS=y CONFIG_CPU_S3C2440=y -CONFIG_CPU_S3C2442=y +CONFIG_S3C2440_DMA=y # -# S3C2410 Boot +# S3C2440 Machines # -# CONFIG_S3C2410_BOOT_WATCHDOG is not set -# CONFIG_S3C2410_BOOT_ERROR_RESET is not set +CONFIG_MACH_ANUBIS=y +CONFIG_MACH_OSIRIS=y +CONFIG_MACH_RX3715=y +CONFIG_ARCH_S3C2440=y +CONFIG_MACH_NEXCODER_2440=y +CONFIG_SMDK2440_CPU2440=y +CONFIG_CPU_S3C2442=y # -# S3C2410 Setup +# S3C2442 Machines # -CONFIG_S3C2410_DMA=y -# CONFIG_S3C2410_DMA_DEBUG is not set -# CONFIG_S3C2410_PM_DEBUG is not set -# CONFIG_S3C2410_PM_CHECK is not set -CONFIG_PM_SIMTEC=y -CONFIG_S3C2410_LOWLEVEL_UART_PORT=0 +CONFIG_SMDK2440_CPU2442=y # # Processor Type @@ -203,6 +215,7 @@ CONFIG_CPU_CP15_MMU=y # CONFIG_CPU_DCACHE_DISABLE is not set # CONFIG_CPU_DCACHE_WRITETHROUGH is not set # CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set # # Bus support -- cgit v1.2.3 From 6db3eee422f80b9d440ea4c08280b52ac4bfa903 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 12 Feb 2007 16:03:22 +0100 Subject: [ARM] 4163/1: S3C2410: minor typo in init comment Fix a reference to s3c2440 in the s3c2410 cpu file Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/s3c2410.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c index d96fdcf2d2e3..1a86a9803753 100644 --- a/arch/arm/mach-s3c2410/s3c2410.c +++ b/arch/arm/mach-s3c2410/s3c2410.c @@ -110,7 +110,7 @@ static struct sys_device s3c2410_sysdev = { /* need to register class before we actually register the device, and * we also need to ensure that it has been initialised before any of the - * drivers even try to use it (even if not on an s3c2440 based system) + * drivers even try to use it (even if not on an s3c2410 based system) * as a driver which may support both 2410 and 2440 may try and use it. */ -- cgit v1.2.3 From 6fb9c4f87018f90d7aa415c5c8a4b22e6a000c5b Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 12 Feb 2007 18:57:05 +0100 Subject: [ARM] 4164/1: S3C2412: Add SMDK2412 to SMDK2413 Our current support for the SMDK2413 is the same as the SMDK2412 (which is very similar), so add SMDK2412 to the list of machines that mach-smdk2413.c supports Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2412/mach-smdk2413.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c index 32b15617ef2a..e385069b5ea1 100644 --- a/arch/arm/mach-s3c2412/mach-smdk2413.c +++ b/arch/arm/mach-s3c2412/mach-smdk2413.c @@ -126,6 +126,19 @@ MACHINE_START(S3C2413, "S3C2413") .timer = &s3c24xx_timer, MACHINE_END +MACHINE_START(SMDK2412, "SMDK2412") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .fixup = smdk2413_fixup, + .init_irq = s3c24xx_init_irq, + .map_io = smdk2413_map_io, + .init_machine = smdk2413_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END + MACHINE_START(SMDK2413, "SMDK2413") /* Maintainer: Ben Dooks */ .phys_io = S3C2410_PA_UART, -- cgit v1.2.3 From 4b210faf0944172e55489bef83babf520bccc1c4 Mon Sep 17 00:00:00 2001 From: Matt Reimer Date: Mon, 12 Feb 2007 21:00:32 +0100 Subject: [ARM] 4169/1: S3C2410: align to a cache line Align the code to the start of the next cache line, rather than the start of the next 256-byte page. (On i386 and ARM, the ".align" assembler directive takes its first argument as the number of low-order bits that must be zero, not the number of words comprising a cache line.) Supercedes patch 4166. Signed-off-by: Matt Reimer Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/sleep.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/sleep.S b/arch/arm/mach-s3c2410/sleep.S index 9179a1024588..637aaba65390 100644 --- a/arch/arm/mach-s3c2410/sleep.S +++ b/arch/arm/mach-s3c2410/sleep.S @@ -59,7 +59,7 @@ ENTRY(s3c2410_cpu_suspend) b s3c2410_do_sleep @ @@ align next bit of code to cache line - .align 8 + .align 5 s3c2410_do_sleep: streq r7, [ r4 ] @ SDRAM sleep command streq r8, [ r5 ] @ SDRAM power-down config -- cgit v1.2.3 From 07b04595e3630594773223874827f5bbd03fc289 Mon Sep 17 00:00:00 2001 From: Matt Reimer Date: Mon, 12 Feb 2007 21:05:02 +0100 Subject: [ARM] 4170/1: S3C2410: don't save and restore cp register 15 Don't save and restore cp register 15 since it is only a test register on S3C2410. This is probably a leftover from the PXA sleep.S from which this was derived. Supersedes patch 4167. Signed-off-by: Matt Reimer Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/plat-s3c24xx/sleep.S | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c24xx/sleep.S b/arch/arm/plat-s3c24xx/sleep.S index 2018c2e1dcc5..435349dc3243 100644 --- a/arch/arm/plat-s3c24xx/sleep.S +++ b/arch/arm/plat-s3c24xx/sleep.S @@ -64,11 +64,10 @@ ENTRY(s3c2410_cpu_save) @@ store co-processor registers - mrc p15, 0, r4, c15, c1, 0 @ CP access register - mrc p15, 0, r5, c13, c0, 0 @ PID - mrc p15, 0, r6, c3, c0, 0 @ Domain ID - mrc p15, 0, r7, c2, c0, 0 @ translation table base address - mrc p15, 0, r8, c1, c0, 0 @ control register + mrc p15, 0, r4, c13, c0, 0 @ PID + mrc p15, 0, r5, c3, c0, 0 @ Domain ID + mrc p15, 0, r6, c2, c0, 0 @ translation table base address + mrc p15, 0, r7, c1, c0, 0 @ control register stmia r0, { r4 - r13 } @@ -141,10 +140,9 @@ ENTRY(s3c2410_cpu_resume) ldr r0, s3c2410_sleep_save_phys @ address of restore block ldmia r0, { r4 - r13 } - mcr p15, 0, r4, c15, c1, 0 @ CP access register - mcr p15, 0, r5, c13, c0, 0 @ PID - mcr p15, 0, r6, c3, c0, 0 @ Domain ID - mcr p15, 0, r7, c2, c0, 0 @ translation table base + mcr p15, 0, r4, c13, c0, 0 @ PID + mcr p15, 0, r5, c3, c0, 0 @ Domain ID + mcr p15, 0, r6, c2, c0, 0 @ translation table base #ifdef CONFIG_DEBUG_RESUME mov r3, #'R' @@ -152,7 +150,7 @@ ENTRY(s3c2410_cpu_resume) #endif ldr r2, =resume_with_mmu - mcr p15, 0, r8, c1, c0, 0 @ turn on MMU, etc + mcr p15, 0, r7, c1, c0, 0 @ turn on MMU, etc nop @ second-to-last before mmu mov pc, r2 @ go back to virtual address -- cgit v1.2.3 From 0dcfc328ccd1d475f10a33c0ccf10bda869d4a83 Mon Sep 17 00:00:00 2001 From: Arnaud Patard Date: Tue, 13 Feb 2007 00:18:33 +0100 Subject: [ARM] 4173/1: S3C24XX usb device platform datas This patch is adding the functions and structures used for handling the S3C24XX udc driver platform datas. Signed-off-by: Arnaud Patard Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/plat-s3c24xx/devs.c | 15 +++++++++++++++ include/asm-arm/arch-s3c2410/udc.h | 34 ++++++++++++++++++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 include/asm-arm/arch-s3c2410/udc.h (limited to 'arch') diff --git a/arch/arm/plat-s3c24xx/devs.c b/arch/arm/plat-s3c24xx/devs.c index 6d46c4e2a4f7..0fe53b39cb2f 100644 --- a/arch/arm/plat-s3c24xx/devs.c +++ b/arch/arm/plat-s3c24xx/devs.c @@ -29,6 +29,7 @@ #include #include +#include #include #include @@ -230,6 +231,20 @@ struct platform_device s3c_device_usbgadget = { EXPORT_SYMBOL(s3c_device_usbgadget); +void __init s3c24xx_udc_set_platdata(struct s3c2410_udc_mach_info *pd) +{ + struct s3c2410_udc_mach_info *npd; + + npd = kmalloc(sizeof(*npd), GFP_KERNEL); + if (npd) { + memcpy(npd, pd, sizeof(*npd)); + s3c_device_usbgadget.dev.platform_data = npd; + } else { + printk(KERN_ERR "no memory for udc platform data\n"); + } +} + + /* Watchdog */ static struct resource s3c_wdt_resource[] = { diff --git a/include/asm-arm/arch-s3c2410/udc.h b/include/asm-arm/arch-s3c2410/udc.h new file mode 100644 index 000000000000..2529effb8078 --- /dev/null +++ b/include/asm-arm/arch-s3c2410/udc.h @@ -0,0 +1,34 @@ +/* linux/include/asm/arch-s3c2410/udc.h + * + * Copyright (c) 2005 Arnaud Patard + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * + * Changelog: + * 14-Mar-2005 RTP Created file + * 02-Aug-2005 RTP File rename + * 07-Sep-2005 BJD Minor cleanups, changed cmd to enum +*/ + +#ifndef __ASM_ARM_ARCH_UDC_H +#define __ASM_ARM_ARCH_UDC_H + +enum s3c2410_udc_cmd_e { + S3C2410_UDC_P_ENABLE = 1, /* Pull-up enable */ + S3C2410_UDC_P_DISABLE = 2, /* Pull-up disable */ + S3C2410_UDC_P_RESET = 3, /* UDC reset, in case of */ +}; + +struct s3c2410_udc_mach_info { + void (*udc_command)(enum s3c2410_udc_cmd_e); + unsigned int vbus_pin; + unsigned char vbus_pin_inverted; +}; + +extern void __init s3c24xx_udc_set_platdata(struct s3c2410_udc_mach_info *); + +#endif /* __ASM_ARM_ARCH_UDC_H */ -- cgit v1.2.3 From 71a9c4241278c8104ff30233b9247c0857c404d7 Mon Sep 17 00:00:00 2001 From: Arnaud Patard Date: Tue, 13 Feb 2007 00:21:26 +0100 Subject: [ARM] 4174/1: H1940 usb device definitions This patch is adding the usb device controller to the h1940 device list. It's also adding the code to handle the usb pull-ups. Signed-off-by: Arnaud Patard Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/mach-h1940.c | 48 +++++++++++++++++++++++++++++++++++++- 1 file changed, 47 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 5af26e177966..68f11efdd140 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -33,10 +33,13 @@ #include #include +#include +#include #include #include #include +#include #include #include @@ -102,6 +105,32 @@ void h1940_latch_control(unsigned int clear, unsigned int set) EXPORT_SYMBOL_GPL(h1940_latch_control); +static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd) +{ + printk(KERN_DEBUG "udc: pullup(%d)\n",cmd); + + switch (cmd) + { + case S3C2410_UDC_P_ENABLE : + h1940_latch_control(0, H1940_LATCH_USB_DP); + break; + case S3C2410_UDC_P_DISABLE : + h1940_latch_control(H1940_LATCH_USB_DP, 0); + break; + case S3C2410_UDC_P_RESET : + break; + default: + break; + } +} + +static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = { + .udc_command = h1940_udc_pullup, + .vbus_pin = S3C2410_GPG5, + .vbus_pin_inverted = 1, +}; + + /** * Set lcd on or off @@ -152,6 +181,7 @@ static struct platform_device *h1940_devices[] __initdata = { &s3c_device_wdt, &s3c_device_i2c, &s3c_device_iis, + &s3c_device_usbgadget, }; static struct s3c24xx_board h1940_board __initdata = { @@ -179,7 +209,23 @@ static void __init h1940_init_irq(void) static void __init h1940_init(void) { + u32 tmp; + s3c24xx_fb_set_platdata(&h1940_lcdcfg); + s3c24xx_udc_set_platdata(&h1940_udc_cfg); + + /* Turn off suspend on both USB ports, and switch the + * selectable USB port to USB device mode. */ + + s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | + S3C2410_MISCCR_USBSUSPND0 | + S3C2410_MISCCR_USBSUSPND1, 0x0); + + tmp = ( + 0x78 << S3C2410_PLLCON_MDIVSHIFT) + | (0x02 << S3C2410_PLLCON_PDIVSHIFT) + | (0x03 << S3C2410_PLLCON_SDIVSHIFT); + writel(tmp, S3C2410_UPLLCON); } MACHINE_START(H1940, "IPAQ-H1940") @@ -189,6 +235,6 @@ MACHINE_START(H1940, "IPAQ-H1940") .boot_params = S3C2410_SDRAM_PA + 0x100, .map_io = h1940_map_io, .init_irq = h1940_init_irq, - .init_machine = h1940_init, + .init_machine = h1940_init, .timer = &s3c24xx_timer, MACHINE_END -- cgit v1.2.3 From ecd1b171a76bb73196dbce4da9f64a4a0a9d098f Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 13 Feb 2007 00:39:08 +0100 Subject: [ARM] 4175/1: SMDK2413: add udc pull-up control USB gadget pull-up control and device addition for the SMDK2413/SMDK2412 board. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2412/mach-smdk2413.c | 41 ++++++++++++++++++++++++++++++++++- 1 file changed, 40 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c index e385069b5ea1..b5befce6c8d3 100644 --- a/arch/arm/mach-s3c2412/mach-smdk2413.c +++ b/arch/arm/mach-s3c2412/mach-smdk2413.c @@ -37,6 +37,7 @@ #include #include +#include #include #include @@ -75,12 +76,38 @@ static struct s3c2410_uartcfg smdk2413_uartcfgs[] __initdata = { } }; +static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd) +{ + printk(KERN_DEBUG "udc: pullup(%d)\n",cmd); + + switch (cmd) + { + case S3C2410_UDC_P_ENABLE : + s3c2410_gpio_setpin(S3C2410_GPF2, 1); + break; + case S3C2410_UDC_P_DISABLE : + s3c2410_gpio_setpin(S3C2410_GPF2, 0); + break; + case S3C2410_UDC_P_RESET : + break; + default: + break; + } +} + + +static struct s3c2410_udc_mach_info smdk2413_udc_cfg __initdata = { + .udc_command = smdk2413_udc_pullup, +}; + + static struct platform_device *smdk2413_devices[] __initdata = { &s3c_device_usb, //&s3c_device_lcd, &s3c_device_wdt, &s3c_device_i2c, &s3c_device_iis, + &s3c_device_usbgadget, }; static struct s3c24xx_board smdk2413_board __initdata = { @@ -109,7 +136,19 @@ static void __init smdk2413_map_io(void) } static void __init smdk2413_machine_init(void) -{ +{ /* Turn off suspend on both USB ports, and switch the + * selectable USB port to USB device mode. */ + + s3c2410_gpio_setpin(S3C2410_GPF2, 0); + s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT); + + s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | + S3C2410_MISCCR_USBSUSPND0 | + S3C2410_MISCCR_USBSUSPND1, 0x0); + + + s3c24xx_udc_set_platdata(&smdk2413_udc_cfg); + smdk_machine_init(); } -- cgit v1.2.3 From d2a76020e3a52c6370a7d603082b4cdb3db0703e Mon Sep 17 00:00:00 2001 From: Arnaud Patard Date: Tue, 13 Feb 2007 00:50:34 +0100 Subject: [ARM] 4176/1: H1940 leds H1940 leds device addition. Signed-off-by: Arnaud Patard Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/mach-h1940.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 68f11efdd140..2b495b7b427b 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -175,6 +175,11 @@ static struct s3c2410fb_mach_info h1940_lcdcfg __initdata = { .bpp= {16,16,16}, }; +static struct platform_device s3c_device_leds = { + .name = "h1940-leds", + .id = -1, +}; + static struct platform_device *h1940_devices[] __initdata = { &s3c_device_usb, &s3c_device_lcd, @@ -182,6 +187,7 @@ static struct platform_device *h1940_devices[] __initdata = { &s3c_device_i2c, &s3c_device_iis, &s3c_device_usbgadget, + &s3c_device_leds, }; static struct s3c24xx_board h1940_board __initdata = { -- cgit v1.2.3 From 0c6022d453ecebdace0ce15434c7108e158149ca Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 13 Feb 2007 13:02:52 +0100 Subject: [ARM] 4177/1: S3C24XX: Add DMA channel allocation order Allow the CPU code, and any board specific initialisation code to change the allocation order of the DMA channels, or stop a peripheral allocating any DMA at-all. This is due to the scarce mapping of DMA channels on some earlier S3C24XX cpus, where the selection changes depending on the channel in use. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- Documentation/arm/Samsung-S3C24XX/DMA.txt | 46 +++++++++++++++++++++++++++++ arch/arm/plat-s3c24xx/dma.c | 49 +++++++++++++++++++++++++++++-- include/asm-arm/plat-s3c24xx/dma.h | 25 ++++++++++++++++ 3 files changed, 117 insertions(+), 3 deletions(-) create mode 100644 Documentation/arm/Samsung-S3C24XX/DMA.txt (limited to 'arch') diff --git a/Documentation/arm/Samsung-S3C24XX/DMA.txt b/Documentation/arm/Samsung-S3C24XX/DMA.txt new file mode 100644 index 000000000000..37f4edcc5d87 --- /dev/null +++ b/Documentation/arm/Samsung-S3C24XX/DMA.txt @@ -0,0 +1,46 @@ + S3C2410 DMA + =========== + +Introduction +------------ + + The kernel provides an interface to manage DMA transfers + using the DMA channels in the cpu, so that the central + duty of managing channel mappings, and programming the + channel generators is in one place. + + +DMA Channel Ordering +-------------------- + + Many of the range do not have connections for the DMA + channels to all sources, which means that some devices + have a restricted number of channels that can be used. + + To allow flexibilty for each cpu type and board, the + dma code can be given an dma ordering structure which + allows the order of channel search to be specified, as + well as allowing the prohibition of certain claims. + + struct s3c24xx_dma_order has a list of channels, and + each channel within has a slot for a list of dma + channel numbers. The slots are searched in order, for + the presence of a dma channel number with DMA_CH_VALID + orred in. + + If the order has the flag DMA_CH_NEVER set, then after + checking the channel list, the system will return no + found channel, thus denying the request. + + A board support file can call s3c24xx_dma_order_set() + to register an complete ordering set. The routine will + copy the data, so the original can be discared with + __initdata. + + +Authour +------- + +Ben Dooks, +Copyright (c) 2007 Ben Dooks, Simtec Electronics +Licensed under the GPL v2 diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c index c784e1f816bb..44e39438b9d8 100644 --- a/arch/arm/plat-s3c24xx/dma.c +++ b/arch/arm/plat-s3c24xx/dma.c @@ -1354,18 +1354,22 @@ static inline int is_channel_valid(unsigned int channel) return (channel & DMA_CH_VALID); } +static struct s3c24xx_dma_order *dma_order; + + /* s3c2410_dma_map_channel() * * turn the virtual channel number into a real, and un-used hardware * channel. * - * currently this code uses first-free channel from the specified harware - * map, not taking into account anything that the board setup code may - * have to say about the likely peripheral set to be in use. + * first, try the dma ordering given to us by either the relevant + * dma code, or the board. Then just find the first usable free + * channel */ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) { + struct s3c24xx_dma_order_ch *ord = NULL; struct s3c24xx_dma_map *ch_map; struct s3c2410_dma_chan *dmach; int ch; @@ -1375,6 +1379,27 @@ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) ch_map = dma_sel.map + channel; + /* first, try the board mapping */ + + if (dma_order) { + ord = &dma_order->channels[channel]; + + for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) { + if (!is_channel_valid(ord->list[ch])) + continue; + + if (s3c2410_chans[ord->list[ch]].in_use == 0) { + ch = ord->list[ch] & ~DMA_CH_VALID; + goto found; + } + } + + if (ord->flags & DMA_CH_NEVER) + return NULL; + } + + /* second, search the channel map for first free */ + for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) { if (!is_channel_valid(ch_map->channels[ch])) continue; @@ -1390,6 +1415,7 @@ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) /* update our channel mapping */ + found: dmach = &s3c2410_chans[ch]; dma_chan_map[channel] = dmach; @@ -1439,3 +1465,20 @@ int __init s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel) return 0; } + +int __init s3c24xx_dma_order_set(struct s3c24xx_dma_order *ord) +{ + struct s3c24xx_dma_order *nord = dma_order; + + if (nord == NULL) + nord = kmalloc(sizeof(struct s3c24xx_dma_order), GFP_KERNEL); + + if (nord == NULL) { + printk(KERN_ERR "no memory to store dma channel order\n"); + return -ENOMEM; + } + + dma_order = nord; + memcpy(nord, ord, sizeof(struct s3c24xx_dma_order)); + return 0; +} diff --git a/include/asm-arm/plat-s3c24xx/dma.h b/include/asm-arm/plat-s3c24xx/dma.h index 421b567fa019..15e140c2d4fc 100644 --- a/include/asm-arm/plat-s3c24xx/dma.h +++ b/include/asm-arm/plat-s3c24xx/dma.h @@ -14,6 +14,7 @@ extern struct sysdev_class dma_sysclass; extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS]; #define DMA_CH_VALID (1<<31) +#define DMA_CH_NEVER (1<<30) struct s3c24xx_dma_addr { unsigned long from; @@ -43,3 +44,27 @@ struct s3c24xx_dma_selection { }; extern int s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel); + +/* struct s3c24xx_dma_order_ch + * + * channel map for one of the `enum dma_ch` dma channels. the list + * entry contains a set of low-level channel numbers, orred with + * DMA_CH_VALID, which are checked in the order in the array. +*/ + +struct s3c24xx_dma_order_ch { + unsigned int list[S3C2410_DMA_CHANNELS]; /* list of channels */ + unsigned int flags; /* flags */ +}; + +/* struct s3c24xx_dma_order + * + * information provided by either the core or the board to give the + * dma system a hint on how to allocate channels +*/ + +struct s3c24xx_dma_order { + struct s3c24xx_dma_order_ch channels[DMACH_MAX]; +}; + +extern int s3c24xx_dma_order_set(struct s3c24xx_dma_order *map); -- cgit v1.2.3 From dad8d6c50e08ce2ef87f294fa412351b27d5bb97 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 13 Feb 2007 13:12:16 +0100 Subject: [ARM] 4178/1: S3C2410: DMA ordering list Add DMA ordering list for S3C2410 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/dma.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c index 22c613600caa..6b3452680755 100644 --- a/arch/arm/mach-s3c2410/dma.c +++ b/arch/arm/mach-s3c2410/dma.c @@ -127,8 +127,27 @@ static struct s3c24xx_dma_selection __initdata s3c2410_dma_sel = { .map_size = ARRAY_SIZE(s3c2410_dma_mappings), }; +static struct s3c24xx_dma_order __initdata s3c2410_dma_order = { + .channels = { + [DMACH_SDI] = { + .list = { + [0] = 3 | DMA_CH_VALID, + [1] = 2 | DMA_CH_VALID, + [2] = 0 | DMA_CH_VALID, + }, + }, + [DMACH_I2S_IN] = { + .list = { + [0] = 1 | DMA_CH_VALID, + [1] = 2 | DMA_CH_VALID, + }, + }, + }, +}; + static int s3c2410_dma_add(struct sys_device *sysdev) { + s3c24xx_dma_order_set(&s3c2410_dma_order); return s3c24xx_dma_init_map(&s3c2410_dma_sel); } -- cgit v1.2.3 From bd65c82b9ee506950e1856e9af60be9fc627bfaa Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 13 Feb 2007 13:14:12 +0100 Subject: [ARM] 4179/1: S3C2440: DMA ordering list Add DMA ordering list for S3C2440 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2440/dma.c | 44 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 44 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2440/dma.c b/arch/arm/mach-s3c2440/dma.c index 8e51137620f2..2bb2926554c8 100644 --- a/arch/arm/mach-s3c2440/dma.c +++ b/arch/arm/mach-s3c2440/dma.c @@ -147,8 +147,52 @@ static struct s3c24xx_dma_selection __initdata s3c2440_dma_sel = { .map_size = ARRAY_SIZE(s3c2440_dma_mappings), }; +static struct s3c24xx_dma_order __initdata s3c2440_dma_order = { + .channels = { + [DMACH_SDI] = { + .list = { + [0] = 3 | DMA_CH_VALID, + [1] = 2 | DMA_CH_VALID, + [2] = 1 | DMA_CH_VALID, + [3] = 0 | DMA_CH_VALID, + }, + }, + [DMACH_I2S_IN] = { + .list = { + [0] = 1 | DMA_CH_VALID, + [1] = 2 | DMA_CH_VALID, + }, + }, + [DMACH_I2S_OUT] = { + .list = { + [0] = 2 | DMA_CH_VALID, + [1] = 1 | DMA_CH_VALID, + }, + }, + [DMACH_PCM_IN] = { + .list = { + [0] = 2 | DMA_CH_VALID, + [1] = 1 | DMA_CH_VALID, + }, + }, + [DMACH_PCM_OUT] = { + .list = { + [0] = 1 | DMA_CH_VALID, + [1] = 3 | DMA_CH_VALID, + }, + }, + [DMACH_MIC_IN] = { + .list = { + [0] = 3 | DMA_CH_VALID, + [1] = 2 | DMA_CH_VALID, + }, + }, + }, +}; + static int s3c2440_dma_add(struct sys_device *sysdev) { + s3c24xx_dma_order_set(&s3c2440_dma_order); return s3c24xx_dma_init_map(&s3c2440_dma_sel); } -- cgit v1.2.3 From 5ac602b2eac4ee58e2497f44c39a5dd8385d2c87 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 13 Feb 2007 17:48:59 +0100 Subject: [ARM] 4188/1: S3C24XX: add CRAMFS to s3c2410_defconfig Add cramfs support in by default, as a lot of our initrds are cramfs images. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/configs/s3c2410_defconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index e8f9375764d6..7c8025bc278a 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit # Linux kernel version: 2.6.20 -# Mon Feb 12 13:32:08 2007 +# Tue Feb 13 16:43:14 2007 # CONFIG_ARM=y # CONFIG_GENERIC_TIME is not set @@ -1220,7 +1220,7 @@ CONFIG_JFFS2_FS_WRITEBUFFER=y CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set -# CONFIG_CRAMFS is not set +CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set -- cgit v1.2.3 From 6df26700c0884cb3cce2b9fa4795888f86ca4d8f Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Tue, 13 Feb 2007 17:11:04 +0100 Subject: [ARM] 4182/1: iop3xx: fix the ioremap implementation to not remap static ranges Implement a custom ioremap implementation for iop3xx. This saves establishing new mappings. It also cleans up the PCI IO resource to be a physical address rather than a virtual address as Russell pointed out on the original iop13xx port. Signed-off-by: Dan Williams Signed-off-by: Russell King --- arch/arm/plat-iop/Makefile | 2 +- arch/arm/plat-iop/io.c | 58 +++++++++++++++++++++++++++++++++++++++ arch/arm/plat-iop/pci.c | 6 ++-- include/asm-arm/arch-iop32x/io.h | 10 +++++-- include/asm-arm/arch-iop33x/io.h | 9 +++++- include/asm-arm/hardware/iop3xx.h | 14 ++++++++++ 6 files changed, 92 insertions(+), 7 deletions(-) create mode 100644 arch/arm/plat-iop/io.c (limited to 'arch') diff --git a/arch/arm/plat-iop/Makefile b/arch/arm/plat-iop/Makefile index 23da00b11517..ed91463967af 100644 --- a/arch/arm/plat-iop/Makefile +++ b/arch/arm/plat-iop/Makefile @@ -2,7 +2,7 @@ # Makefile for the linux kernel. # -obj-y := gpio.o i2c.o pci.o setup.o time.o +obj-y := gpio.o i2c.o pci.o setup.o time.o io.o obj-m := obj-n := obj- := diff --git a/arch/arm/plat-iop/io.c b/arch/arm/plat-iop/io.c new file mode 100644 index 000000000000..f7eccecf2e47 --- /dev/null +++ b/arch/arm/plat-iop/io.c @@ -0,0 +1,58 @@ +/* + * iop3xx custom ioremap implementation + * Copyright (c) 2006, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place - Suite 330, Boston, MA 02111-1307 USA. + * + */ +#include +#include +#include +#include + +void * __iomem __iop3xx_ioremap(unsigned long cookie, size_t size, + unsigned long flags) +{ + void __iomem * retval; + + switch (cookie) { + case IOP3XX_PCI_LOWER_IO_PA ... IOP3XX_PCI_UPPER_IO_PA: + retval = (void *) IOP3XX_PCI_IO_PHYS_TO_VIRT(cookie); + break; + case IOP3XX_PERIPHERAL_PHYS_BASE ... IOP3XX_PERIPHERAL_UPPER_PA: + retval = (void *) IOP3XX_PMMR_PHYS_TO_VIRT(cookie); + break; + default: + retval = __ioremap(cookie, size, flags); + } + + return retval; +} +EXPORT_SYMBOL(__iop3xx_ioremap); + +void __iop3xx_iounmap(void __iomem *addr) +{ + extern void __iounmap(volatile void __iomem *addr); + + switch ((u32) addr) { + case IOP3XX_PCI_LOWER_IO_VA ... IOP3XX_PCI_UPPER_IO_VA: + case IOP3XX_PERIPHERAL_VIRT_BASE ... IOP3XX_PERIPHERAL_UPPER_VA: + goto skip; + } + __iounmap(addr); + +skip: + return; +} +EXPORT_SYMBOL(__iop3xx_iounmap); diff --git a/arch/arm/plat-iop/pci.c b/arch/arm/plat-iop/pci.c index e647812654f2..b5f6ec35aafb 100644 --- a/arch/arm/plat-iop/pci.c +++ b/arch/arm/plat-iop/pci.c @@ -196,8 +196,8 @@ int iop3xx_pci_setup(int nr, struct pci_sys_data *sys) if (!res) panic("PCI: unable to alloc resources"); - res[0].start = IOP3XX_PCI_LOWER_IO_VA; - res[0].end = IOP3XX_PCI_LOWER_IO_VA + IOP3XX_PCI_IO_WINDOW_SIZE - 1; + res[0].start = IOP3XX_PCI_LOWER_IO_PA; + res[0].end = IOP3XX_PCI_LOWER_IO_PA + IOP3XX_PCI_IO_WINDOW_SIZE - 1; res[0].name = "IOP3XX PCI I/O Space"; res[0].flags = IORESOURCE_IO; request_resource(&ioport_resource, &res[0]); @@ -209,7 +209,7 @@ int iop3xx_pci_setup(int nr, struct pci_sys_data *sys) request_resource(&iomem_resource, &res[1]); sys->mem_offset = IOP3XX_PCI_LOWER_MEM_PA - IOP3XX_PCI_LOWER_MEM_BA; - sys->io_offset = IOP3XX_PCI_LOWER_IO_VA - IOP3XX_PCI_LOWER_IO_BA; + sys->io_offset = IOP3XX_PCI_LOWER_IO_PA - IOP3XX_PCI_LOWER_IO_BA; sys->resource[0] = &res[0]; sys->resource[1] = &res[1]; diff --git a/include/asm-arm/arch-iop32x/io.h b/include/asm-arm/arch-iop32x/io.h index 12d9ee02cde3..5f570a598a37 100644 --- a/include/asm-arm/arch-iop32x/io.h +++ b/include/asm-arm/arch-iop32x/io.h @@ -13,10 +13,16 @@ #include -#define IO_SPACE_LIMIT 0xffffffff +extern void __iomem * __ioremap(unsigned long, size_t, unsigned long); +extern void __iomem *__iop3xx_ioremap(unsigned long cookie, size_t size, + unsigned long flags); +extern void __iop3xx_iounmap(void __iomem *addr); -#define __io(p) ((void __iomem *)(p)) +#define IO_SPACE_LIMIT 0xffffffff +#define __io(p) ((void __iomem *)IOP3XX_PCI_IO_PHYS_TO_VIRT(p)) #define __mem_pci(a) (a) +#define __arch_ioremap(a, s, f) __iop3xx_ioremap(a, s, f) +#define __arch_iounmap(a) __iop3xx_iounmap(a) #endif diff --git a/include/asm-arm/arch-iop33x/io.h b/include/asm-arm/arch-iop33x/io.h index c017402bab96..1bb5071e1fa8 100644 --- a/include/asm-arm/arch-iop33x/io.h +++ b/include/asm-arm/arch-iop33x/io.h @@ -13,9 +13,16 @@ #include +extern void __iomem * __ioremap(unsigned long, size_t, unsigned long); +extern void __iomem *__iop3xx_ioremap(unsigned long cookie, size_t size, + unsigned long flags); +extern void __iop3xx_iounmap(void __iomem *addr); + #define IO_SPACE_LIMIT 0xffffffff -#define __io(p) ((void __iomem *)(p)) +#define __io(p) ((void __iomem *)IOP3XX_PCI_IO_PHYS_TO_VIRT(p)) #define __mem_pci(a) (a) +#define __arch_ioremap(a, s, f) __iop3xx_ioremap(a, s, f) +#define __arch_iounmap(a) __iop3xx_iounmap(a) #endif diff --git a/include/asm-arm/hardware/iop3xx.h b/include/asm-arm/hardware/iop3xx.h index 13ac8a4cd01f..adb96c72ecdd 100644 --- a/include/asm-arm/hardware/iop3xx.h +++ b/include/asm-arm/hardware/iop3xx.h @@ -37,6 +37,13 @@ extern void gpio_line_set(int line, int value); #define IOP3XX_PERIPHERAL_PHYS_BASE 0xffffe000 #define IOP3XX_PERIPHERAL_VIRT_BASE 0xfeffe000 #define IOP3XX_PERIPHERAL_SIZE 0x00002000 +#define IOP3XX_PERIPHERAL_UPPER_PA (IOP3XX_PERIPHERAL_PHYS_BASE +\ + IOP3XX_PERIPHERAL_SIZE - 1) +#define IOP3XX_PERIPHERAL_UPPER_VA (IOP3XX_PERIPHERAL_VIRT_BASE +\ + IOP3XX_PERIPHERAL_SIZE - 1) +#define IOP3XX_PMMR_PHYS_TO_VIRT(addr) (u32) ((u32) addr -\ + (IOP3XX_PERIPHERAL_PHYS_BASE\ + - IOP3XX_PERIPHERAL_VIRT_BASE)) #define IOP3XX_REG_ADDR(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + (reg)) /* Address Translation Unit */ @@ -258,6 +265,13 @@ extern void gpio_line_set(int line, int value); #define IOP3XX_PCI_LOWER_IO_PA 0x90000000 #define IOP3XX_PCI_LOWER_IO_VA 0xfe000000 #define IOP3XX_PCI_LOWER_IO_BA (*IOP3XX_OIOWTVR) +#define IOP3XX_PCI_UPPER_IO_PA (IOP3XX_PCI_LOWER_IO_PA +\ + IOP3XX_PCI_IO_WINDOW_SIZE - 1) +#define IOP3XX_PCI_UPPER_IO_VA (IOP3XX_PCI_LOWER_IO_VA +\ + IOP3XX_PCI_IO_WINDOW_SIZE - 1) +#define IOP3XX_PCI_IO_PHYS_TO_VIRT(addr) (((u32) addr -\ + IOP3XX_PCI_LOWER_IO_PA) +\ + IOP3XX_PCI_LOWER_IO_VA) #ifndef __ASSEMBLY__ -- cgit v1.2.3 From dfc544c7216b276c1e9c0c753299692df4068c44 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Tue, 13 Feb 2007 17:11:34 +0100 Subject: [ARM] 4183/1: do_undefinstr: read svc undefined instructions with svc privileges do_undefinstr currently does not expect undefined instructions in kernel code, since it always uses get_user() to read the instruction. Dereference the 'pc' pointer directly in the SVC case. Per Nicolas Pitre's note, kernel code is never in thumb mode. Signed-off-by: Dan Williams Signed-off-by: Russell King --- arch/arm/kernel/traps.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 329609b84d3b..24095601359b 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -282,7 +282,10 @@ asmlinkage void do_undefinstr(struct pt_regs *regs) regs->ARM_pc -= correction; pc = (void __user *)instruction_pointer(regs); - if (thumb_mode(regs)) { + + if (processor_mode(regs) == SVC_MODE) { + instr = *(u32 *) pc; + } else if (thumb_mode(regs)) { get_user(instr, (u16 __user *)pc); } else { get_user(instr, (u32 __user *)pc); -- cgit v1.2.3 From 588ef7693574cfbcb228f48d5478c2b39a9b0c9f Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Tue, 13 Feb 2007 17:12:04 +0100 Subject: [ARM] 4184/1: iop: cp6 access handler (undef_hook) Enable svc access to cp6 via an undefined instruction hook. Do not enable access for usr code. This patch also makes iop13xx select PLAT_IOP, this requires a small change to drivers/i2c/busses/i2c-iop3xx.c. Per Lennert Buytenhek's note, the cp6 trap routine is moved to arch/arm/plat-iop Per Nicolas Pitre's note, the cp_wait is skipped since the latency to return to the faulting function is longer than cp_wait. Signed-off-by: Dan Williams Signed-off-by: Russell King --- arch/arm/Kconfig | 2 ++ arch/arm/mach-iop13xx/irq.c | 3 +++ arch/arm/mach-iop32x/irq.c | 2 ++ arch/arm/mach-iop33x/irq.c | 2 ++ arch/arm/plat-iop/Makefile | 30 +++++++++++++++++++---- arch/arm/plat-iop/cp6.c | 50 +++++++++++++++++++++++++++++++++++++++ drivers/i2c/busses/i2c-iop3xx.c | 2 +- include/asm-arm/hardware/iop3xx.h | 1 + 8 files changed, 87 insertions(+), 5 deletions(-) create mode 100644 arch/arm/plat-iop/cp6.c (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6783c2e5512d..3f48e35ee61a 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -233,6 +233,8 @@ config ARCH_IOP33X config ARCH_IOP13XX bool "IOP13xx-based" + depends on MMU + select PLAT_IOP select PCI help Support for Intel's IOP13XX (XScale) family of processors. diff --git a/arch/arm/mach-iop13xx/irq.c b/arch/arm/mach-iop13xx/irq.c index dbbc07c38b14..162b93214965 100644 --- a/arch/arm/mach-iop13xx/irq.c +++ b/arch/arm/mach-iop13xx/irq.c @@ -250,11 +250,14 @@ static struct irq_chip iop13xx_irqchip4 = { .unmask = iop13xx_irq_unmask3, }; +extern void iop_init_cp6_handler(void); + void __init iop13xx_init_irq(void) { unsigned int i; u32 cp_flags = iop13xx_cp6_save(); + iop_init_cp6_handler(); /* disable all interrupts */ write_intctl_0(0); diff --git a/arch/arm/mach-iop32x/irq.c b/arch/arm/mach-iop32x/irq.c index 3ec1cd5c4f99..8b0ac5590ae4 100644 --- a/arch/arm/mach-iop32x/irq.c +++ b/arch/arm/mach-iop32x/irq.c @@ -60,6 +60,8 @@ void __init iop32x_init_irq(void) { int i; + iop_init_cp6_handler(); + intctl_write(0); intstr_write(0); if (machine_is_glantank() || diff --git a/arch/arm/mach-iop33x/irq.c b/arch/arm/mach-iop33x/irq.c index 00b37f32d72e..effbe6b782d0 100644 --- a/arch/arm/mach-iop33x/irq.c +++ b/arch/arm/mach-iop33x/irq.c @@ -110,6 +110,8 @@ void __init iop33x_init_irq(void) { int i; + iop_init_cp6_handler(); + intctl0_write(0); intctl1_write(0); intstr0_write(0); diff --git a/arch/arm/plat-iop/Makefile b/arch/arm/plat-iop/Makefile index ed91463967af..3250d732a171 100644 --- a/arch/arm/plat-iop/Makefile +++ b/arch/arm/plat-iop/Makefile @@ -2,7 +2,29 @@ # Makefile for the linux kernel. # -obj-y := gpio.o i2c.o pci.o setup.o time.o io.o -obj-m := -obj-n := -obj- := +obj-y := + +# IOP32X +obj-$(CONFIG_ARCH_IOP32X) += gpio.o +obj-$(CONFIG_ARCH_IOP32X) += i2c.o +obj-$(CONFIG_ARCH_IOP32X) += pci.o +obj-$(CONFIG_ARCH_IOP32X) += setup.o +obj-$(CONFIG_ARCH_IOP32X) += time.o +obj-$(CONFIG_ARCH_IOP32X) += io.o +obj-$(CONFIG_ARCH_IOP32X) += cp6.o + +# IOP33X +obj-$(CONFIG_ARCH_IOP33X) += gpio.o +obj-$(CONFIG_ARCH_IOP33X) += i2c.o +obj-$(CONFIG_ARCH_IOP33X) += pci.o +obj-$(CONFIG_ARCH_IOP33X) += setup.o +obj-$(CONFIG_ARCH_IOP33X) += time.o +obj-$(CONFIG_ARCH_IOP33X) += io.o +obj-$(CONFIG_ARCH_IOP33X) += cp6.o + +# IOP13XX +obj-$(CONFIG_ARCH_IOP13XX) += cp6.o + +obj-m := +obj-n := +obj- := diff --git a/arch/arm/plat-iop/cp6.c b/arch/arm/plat-iop/cp6.c new file mode 100644 index 000000000000..9612a87e2a88 --- /dev/null +++ b/arch/arm/plat-iop/cp6.c @@ -0,0 +1,50 @@ +/* + * IOP Coprocessor-6 access handler + * Copyright (c) 2006, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place - Suite 330, Boston, MA 02111-1307 USA. + * + */ +#include +#include + +static int cp6_trap(struct pt_regs *regs, unsigned int instr) +{ + u32 temp; + + /* enable cp6 access */ + asm volatile ( + "mrc p15, 0, %0, c15, c1, 0\n\t" + "orr %0, %0, #(1 << 6)\n\t" + "mcr p15, 0, %0, c15, c1, 0\n\t" + : "=r"(temp)); + + return 0; +} + +/* permit kernel space cp6 access + * deny user space cp6 access + */ +static struct undef_hook cp6_hook = { + .instr_mask = 0x0f000ff0, + .instr_val = 0x0e000610, + .cpsr_mask = MODE_MASK, + .cpsr_val = SVC_MODE, + .fn = cp6_trap, +}; + +void __init iop_init_cp6_handler(void) +{ + register_undef_hook(&cp6_hook); +} diff --git a/drivers/i2c/busses/i2c-iop3xx.c b/drivers/i2c/busses/i2c-iop3xx.c index d108ab4974cc..b70a7f7daacc 100644 --- a/drivers/i2c/busses/i2c-iop3xx.c +++ b/drivers/i2c/busses/i2c-iop3xx.c @@ -84,7 +84,7 @@ iop3xx_i2c_enable(struct i2c_algo_iop3xx_data *iop3xx_adap) * Every time unit enable is asserted, GPOD needs to be cleared * on IOP3XX to avoid data corruption on the bus. */ -#ifdef CONFIG_PLAT_IOP +#if defined(CONFIG_ARCH_IOP32X) || defined(CONFIG_ARCH_IOP33X) if (iop3xx_adap->id == 0) { gpio_line_set(IOP3XX_GPIO_LINE(7), GPIO_LOW); gpio_line_set(IOP3XX_GPIO_LINE(6), GPIO_LOW); diff --git a/include/asm-arm/hardware/iop3xx.h b/include/asm-arm/hardware/iop3xx.h index adb96c72ecdd..c91b546e20ef 100644 --- a/include/asm-arm/hardware/iop3xx.h +++ b/include/asm-arm/hardware/iop3xx.h @@ -278,6 +278,7 @@ extern void gpio_line_set(int line, int value); void iop3xx_map_io(void); void iop3xx_init_time(unsigned long); unsigned long iop3xx_gettimeoffset(void); +void iop_init_cp6_handler(void); extern struct platform_device iop3xx_i2c0_device; extern struct platform_device iop3xx_i2c1_device; -- cgit v1.2.3 From 69b2e99cf57ab8121d575a04a050314ac9c8f7e1 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Wed, 14 Feb 2007 08:44:43 +0100 Subject: [ARM] 4189/1: AT91: MACB Ethernet clock The MACB Ethernet driver searches for a "macb_clk" clock, so rename the "ether_clk" on the SAM9260 and SAM9263 to "macb_clk". Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/at91sam9260.c | 6 +++--- arch/arm/mach-at91/at91sam9263.c | 6 +++--- 2 files changed, 6 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index e03ee625f40c..86e3a4c46550 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -127,8 +127,8 @@ static struct clk ohci_clk = { .pmc_mask = 1 << AT91SAM9260_ID_UHP, .type = CLK_TYPE_PERIPHERAL, }; -static struct clk ether_clk = { - .name = "ether_clk", +static struct clk macb_clk = { + .name = "macb_clk", .pmc_mask = 1 << AT91SAM9260_ID_EMAC, .type = CLK_TYPE_PERIPHERAL, }; @@ -186,7 +186,7 @@ static struct clk *periph_clocks[] __initdata = { &tc1_clk, &tc2_clk, &ohci_clk, - ðer_clk, + &macb_clk, &isi_clk, &usart3_clk, &usart4_clk, diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index fae6a821a61b..6aa342e8f1b1 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -107,8 +107,8 @@ static struct clk tcb_clk = { .pmc_mask = 1 << AT91SAM9263_ID_TCB, .type = CLK_TYPE_PERIPHERAL, }; -static struct clk ether_clk = { - .name = "ether_clk", +static struct clk macb_clk = { + .name = "macb_clk", .pmc_mask = 1 << AT91SAM9263_ID_EMAC, .type = CLK_TYPE_PERIPHERAL, }; @@ -150,7 +150,7 @@ static struct clk *periph_clocks[] __initdata = { // ac97 &tcb_clk, // pwmc - ðer_clk, + &macb_clk, // 2dge &udc_clk, &isi_clk, -- cgit v1.2.3 From b3a1bde4db9889feb116330bff21214811c940e4 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 14 Feb 2007 19:14:56 +0100 Subject: [ARM] 4108/2: Allow multiple GIC interrupt controllers in a system The current implementation only assumes one GIC to be present in the system. However, there are platforms with more than one cascaded interrupt controllers (RealView/EB MPCore for example). Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/common/gic.c | 109 ++++++++++++++++++++++++++++++----- arch/arm/mach-realview/platsmp.c | 2 +- arch/arm/mach-realview/realview_eb.c | 4 +- include/asm-arm/hardware/gic.h | 5 +- 4 files changed, 101 insertions(+), 19 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c index 09b9d1b6844c..4deece5fbdf4 100644 --- a/arch/arm/common/gic.c +++ b/arch/arm/common/gic.c @@ -14,7 +14,9 @@ * * o There is one CPU Interface per CPU, which sends interrupts sent * by the Distributor, and interrupts generated locally, to the - * associated CPU. + * associated CPU. The base address of the CPU interface is usually + * aliased so that the same address points to different chips depending + * on the CPU it is accessed from. * * Note that IRQs 0-31 are special - they are local to each CPU. * As such, the enable set/clear, pending set/clear and active bit @@ -31,10 +33,38 @@ #include #include -static void __iomem *gic_dist_base; -static void __iomem *gic_cpu_base; static DEFINE_SPINLOCK(irq_controller_lock); +struct gic_chip_data { + unsigned int irq_offset; + void __iomem *dist_base; + void __iomem *cpu_base; +}; + +#ifndef MAX_GIC_NR +#define MAX_GIC_NR 1 +#endif + +static struct gic_chip_data gic_data[MAX_GIC_NR]; + +static inline void __iomem *gic_dist_base(unsigned int irq) +{ + struct gic_chip_data *gic_data = get_irq_chip_data(irq); + return gic_data->dist_base; +} + +static inline void __iomem *gic_cpu_base(unsigned int irq) +{ + struct gic_chip_data *gic_data = get_irq_chip_data(irq); + return gic_data->cpu_base; +} + +static inline unsigned int gic_irq(unsigned int irq) +{ + struct gic_chip_data *gic_data = get_irq_chip_data(irq); + return irq - gic_data->irq_offset; +} + /* * Routines to acknowledge, disable and enable interrupts * @@ -55,8 +85,8 @@ static void gic_ack_irq(unsigned int irq) u32 mask = 1 << (irq % 32); spin_lock(&irq_controller_lock); - writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4); - writel(irq, gic_cpu_base + GIC_CPU_EOI); + writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_CLEAR + (gic_irq(irq) / 32) * 4); + writel(gic_irq(irq), gic_cpu_base(irq) + GIC_CPU_EOI); spin_unlock(&irq_controller_lock); } @@ -65,7 +95,7 @@ static void gic_mask_irq(unsigned int irq) u32 mask = 1 << (irq % 32); spin_lock(&irq_controller_lock); - writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4); + writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_CLEAR + (gic_irq(irq) / 32) * 4); spin_unlock(&irq_controller_lock); } @@ -74,14 +104,14 @@ static void gic_unmask_irq(unsigned int irq) u32 mask = 1 << (irq % 32); spin_lock(&irq_controller_lock); - writel(mask, gic_dist_base + GIC_DIST_ENABLE_SET + (irq / 32) * 4); + writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_SET + (gic_irq(irq) / 32) * 4); spin_unlock(&irq_controller_lock); } #ifdef CONFIG_SMP static void gic_set_cpu(unsigned int irq, cpumask_t mask_val) { - void __iomem *reg = gic_dist_base + GIC_DIST_TARGET + (irq & ~3); + void __iomem *reg = gic_dist_base(irq) + GIC_DIST_TARGET + (gic_irq(irq) & ~3); unsigned int shift = (irq % 4) * 8; unsigned int cpu = first_cpu(mask_val); u32 val; @@ -95,6 +125,37 @@ static void gic_set_cpu(unsigned int irq, cpumask_t mask_val) } #endif +static void fastcall gic_handle_cascade_irq(unsigned int irq, + struct irq_desc *desc) +{ + struct gic_chip_data *chip_data = get_irq_data(irq); + struct irq_chip *chip = get_irq_chip(irq); + unsigned int cascade_irq; + unsigned long status; + + /* primary controller ack'ing */ + chip->ack(irq); + + spin_lock(&irq_controller_lock); + status = readl(chip_data->cpu_base + GIC_CPU_INTACK); + spin_unlock(&irq_controller_lock); + + cascade_irq = (status & 0x3ff); + if (cascade_irq > 1020) + goto out; + if (cascade_irq < 32 || cascade_irq >= NR_IRQS) { + do_bad_IRQ(cascade_irq, desc); + goto out; + } + + cascade_irq += chip_data->irq_offset; + generic_handle_irq(cascade_irq); + + out: + /* primary controller unmasking */ + chip->unmask(irq); +} + static struct irq_chip gic_chip = { .name = "GIC", .ack = gic_ack_irq, @@ -105,15 +166,29 @@ static struct irq_chip gic_chip = { #endif }; -void __init gic_dist_init(void __iomem *base) +void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq) +{ + if (gic_nr >= MAX_GIC_NR) + BUG(); + if (set_irq_data(irq, &gic_data[gic_nr]) != 0) + BUG(); + set_irq_chained_handler(irq, gic_handle_cascade_irq); +} + +void __init gic_dist_init(unsigned int gic_nr, void __iomem *base, + unsigned int irq_start) { unsigned int max_irq, i; u32 cpumask = 1 << smp_processor_id(); + if (gic_nr >= MAX_GIC_NR) + BUG(); + cpumask |= cpumask << 8; cpumask |= cpumask << 16; - gic_dist_base = base; + gic_data[gic_nr].dist_base = base; + gic_data[gic_nr].irq_offset = (irq_start - 1) & ~31; writel(0, base + GIC_DIST_CTRL); @@ -158,8 +233,9 @@ void __init gic_dist_init(void __iomem *base) /* * Setup the Linux IRQ subsystem. */ - for (i = 29; i < max_irq; i++) { + for (i = irq_start; i < gic_data[gic_nr].irq_offset + max_irq; i++) { set_irq_chip(i, &gic_chip); + set_irq_chip_data(i, &gic_data[gic_nr]); set_irq_handler(i, handle_level_irq); set_irq_flags(i, IRQF_VALID | IRQF_PROBE); } @@ -167,9 +243,13 @@ void __init gic_dist_init(void __iomem *base) writel(1, base + GIC_DIST_CTRL); } -void __cpuinit gic_cpu_init(void __iomem *base) +void __cpuinit gic_cpu_init(unsigned int gic_nr, void __iomem *base) { - gic_cpu_base = base; + if (gic_nr >= MAX_GIC_NR) + BUG(); + + gic_data[gic_nr].cpu_base = base; + writel(0xf0, base + GIC_CPU_PRIMASK); writel(1, base + GIC_CPU_CTRL); } @@ -179,6 +259,7 @@ void gic_raise_softirq(cpumask_t cpumask, unsigned int irq) { unsigned long map = *cpus_addr(cpumask); - writel(map << 16 | irq, gic_dist_base + GIC_DIST_SOFTINT); + /* this always happens on GIC0 */ + writel(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT); } #endif diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c index b8484e15dacb..709a9b1ac634 100644 --- a/arch/arm/mach-realview/platsmp.c +++ b/arch/arm/mach-realview/platsmp.c @@ -52,7 +52,7 @@ void __cpuinit platform_secondary_init(unsigned int cpu) * core (e.g. timer irq), then they will not have been enabled * for us: do so */ - gic_cpu_init(__io_address(REALVIEW_GIC_CPU_BASE)); + gic_cpu_init(0, __io_address(REALVIEW_GIC_CPU_BASE)); /* * let the primary processor know we're out of the diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 9741b4d3c9cf..b6a6f68cb699 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -143,8 +143,8 @@ static void __init gic_init_irq(void) writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + 0xd8); writel(0x00000000, __io_address(REALVIEW_SYS_LOCK)); #endif - gic_dist_init(__io_address(REALVIEW_GIC_DIST_BASE)); - gic_cpu_init(__io_address(REALVIEW_GIC_CPU_BASE)); + gic_dist_init(0, __io_address(REALVIEW_GIC_DIST_BASE), 29); + gic_cpu_init(0, __io_address(REALVIEW_GIC_CPU_BASE)); } static void __init realview_eb_init(void) diff --git a/include/asm-arm/hardware/gic.h b/include/asm-arm/hardware/gic.h index 3fa5eb70f64e..966e428ad32c 100644 --- a/include/asm-arm/hardware/gic.h +++ b/include/asm-arm/hardware/gic.h @@ -33,8 +33,9 @@ #define GIC_DIST_SOFTINT 0xf00 #ifndef __ASSEMBLY__ -void gic_dist_init(void __iomem *base); -void gic_cpu_init(void __iomem *base); +void gic_dist_init(unsigned int gic_nr, void __iomem *base, unsigned int irq_start); +void gic_cpu_init(unsigned int gic_nr, void __iomem *base); +void gic_cascade_irq(unsigned int gic_nr, unsigned int irq); void gic_raise_softirq(cpumask_t cpumask, unsigned int irq); #endif -- cgit v1.2.3 From 3edf22ab34e1fdffc8c0c7c7b7da4d0aebdba118 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 14 Feb 2007 19:18:09 +0100 Subject: [ARM] 4190/2: Add the secondary GIC support for the RealView/EB MPCore platform This patch adds the registration of the secondary GIC on the baseboard, together with the IRQ chaining setup. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mach-realview/realview_eb.c | 19 +++++++++++++++++++ include/asm-arm/arch-realview/irqs.h | 5 ++++- include/asm-arm/arch-realview/platform.h | 6 ++++++ 3 files changed, 29 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index b6a6f68cb699..00139143dcc1 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -57,7 +57,21 @@ static struct map_desc realview_eb_io_desc[] __initdata = { .pfn = __phys_to_pfn(REALVIEW_GIC_DIST_BASE), .length = SZ_4K, .type = MT_DEVICE, + }, +#ifdef CONFIG_REALVIEW_MPCORE + { + .virtual = IO_ADDRESS(REALVIEW_GIC1_CPU_BASE), + .pfn = __phys_to_pfn(REALVIEW_GIC1_CPU_BASE), + .length = SZ_4K, + .type = MT_DEVICE, }, { + .virtual = IO_ADDRESS(REALVIEW_GIC1_DIST_BASE), + .pfn = __phys_to_pfn(REALVIEW_GIC1_DIST_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, +#endif + { .virtual = IO_ADDRESS(REALVIEW_SCTL_BASE), .pfn = __phys_to_pfn(REALVIEW_SCTL_BASE), .length = SZ_4K, @@ -145,6 +159,11 @@ static void __init gic_init_irq(void) #endif gic_dist_init(0, __io_address(REALVIEW_GIC_DIST_BASE), 29); gic_cpu_init(0, __io_address(REALVIEW_GIC_CPU_BASE)); +#ifdef CONFIG_REALVIEW_MPCORE + gic_dist_init(1, __io_address(REALVIEW_GIC1_DIST_BASE), 64); + gic_cpu_init(1, __io_address(REALVIEW_GIC1_CPU_BASE)); + gic_cascade_irq(1, IRQ_EB_IRQ1); +#endif } static void __init realview_eb_init(void) diff --git a/include/asm-arm/arch-realview/irqs.h b/include/asm-arm/arch-realview/irqs.h index 76b498eb20a6..5a5db56f86b8 100644 --- a/include/asm-arm/arch-realview/irqs.h +++ b/include/asm-arm/arch-realview/irqs.h @@ -78,6 +78,9 @@ #define IRQ_PMU_SCU6 (IRQ_GIC_START + INT_PMU_SCU6) #define IRQ_PMU_SCU7 (IRQ_GIC_START + INT_PMU_SCU7) +#define IRQ_EB_IRQ1 (IRQ_GIC_START + INT_EB_IRQ1) +#define IRQ_EB_IRQ2 (IRQ_GIC_START + INT_EB_IRQ2) + #define IRQMASK_WDOGINT INTMASK_WDOGINT #define IRQMASK_SOFTINT INTMASK_SOFTINT #define IRQMASK_COMMRx INTMASK_COMMRx @@ -115,4 +118,4 @@ #define IRQMASK_ETH INTMASK_ETH #define IRQMASK_USB INTMASK_USB -#define NR_IRQS (IRQ_GIC_START + 64) +#define NR_IRQS (IRQ_GIC_START + 96) diff --git a/include/asm-arm/arch-realview/platform.h b/include/asm-arm/arch-realview/platform.h index 18d7c18b738c..bf52ca752a75 100644 --- a/include/asm-arm/arch-realview/platform.h +++ b/include/asm-arm/arch-realview/platform.h @@ -212,6 +212,8 @@ #define REALVIEW_TWD_BASE 0x10100700 #define REALVIEW_TWD_SIZE 0x00000100 #define REALVIEW_GIC_DIST_BASE 0x10101000 /* Generic interrupt controller distributor */ +#define REALVIEW_GIC1_CPU_BASE 0x10040000 /* Generic interrupt controller CPU interface */ +#define REALVIEW_GIC1_DIST_BASE 0x10041000 /* Generic interrupt controller distributor */ #endif #define REALVIEW_SMC_BASE 0x10080000 /* SMC */ /* Reserved 0x10090000 - 0x100EFFFF */ @@ -306,7 +308,11 @@ #define INT_USB 29 /* USB controller */ #define INT_TSPENINT 30 /* Touchscreen pen */ #define INT_TSKPADINT 31 /* Touchscreen keypad */ + #else + +#define MAX_GIC_NR 2 + #define INT_AACI 0 #define INT_TIMERINT0_1 1 #define INT_TIMERINT2_3 2 -- cgit v1.2.3 From 4b17244c133689ad0cbdca37ce3e15068f120428 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 14 Feb 2007 19:20:28 +0100 Subject: [ARM] 4109/2: Add support for the RealView/EB MPCore revC platform The kernel originally supported revB only. This patch enables revC by default and adds a config option for building the kernel for the revB platform. Since the SCU base address was hard-coded in the proc-v6.S file (and only valid for RealView/EB revB), this patch also adds a more generic support for defining the SCU information. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mach-realview/Kconfig | 10 ++++++++++ arch/arm/mach-realview/realview_eb.c | 4 ++-- arch/arm/mm/proc-v6.S | 8 +++++--- include/asm-arm/arch-realview/hardware.h | 2 +- include/asm-arm/arch-realview/platform.h | 10 ++++++++++ include/asm-arm/arch-realview/scu.h | 8 ++++++++ include/asm-arm/hardware/arm_scu.h | 2 ++ 7 files changed, 38 insertions(+), 6 deletions(-) create mode 100644 include/asm-arm/arch-realview/scu.h (limited to 'arch') diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig index 17f5f4439fe7..68bc6b226ec7 100644 --- a/arch/arm/mach-realview/Kconfig +++ b/arch/arm/mach-realview/Kconfig @@ -16,4 +16,14 @@ config REALVIEW_MPCORE kernel built with this option enabled is not compatible with other tiles. +config REALVIEW_MPCORE_REVB + bool "Support MPcore RevB tile" + depends on REALVIEW_MPCORE + default n + help + Enable support for the MPCore RevB tile on the Realview platform. + Since there are device address differences, a + kernel built with this option enabled is not compatible with + other tiles. + endmenu diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 00139143dcc1..effe243454e0 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -152,9 +152,9 @@ static void __init gic_init_irq(void) #ifdef CONFIG_REALVIEW_MPCORE unsigned int pldctrl; writel(0x0000a05f, __io_address(REALVIEW_SYS_LOCK)); - pldctrl = readl(__io_address(REALVIEW_SYS_BASE) + 0xd8); + pldctrl = readl(__io_address(REALVIEW_SYS_BASE) + REALVIEW_MPCORE_SYS_PLD_CTRL1); pldctrl |= 0x00800000; /* New irq mode */ - writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + 0xd8); + writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + REALVIEW_MPCORE_SYS_PLD_CTRL1); writel(0x00000000, __io_address(REALVIEW_SYS_LOCK)); #endif gic_dist_init(0, __io_address(REALVIEW_GIC_DIST_BASE), 29); diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S index 7b1843befb9c..f27d9eb64803 100644 --- a/arch/arm/mm/proc-v6.S +++ b/arch/arm/mm/proc-v6.S @@ -14,10 +14,13 @@ #include #include #include -#include #include #include +#ifdef CONFIG_SMP +#include +#endif + #include "proc-macros.S" #define D_CACHE_LINE_SIZE 32 @@ -183,8 +186,7 @@ __v6_setup: /* Set up the SCU on core 0 only */ mrc p15, 0, r0, c0, c0, 5 @ CPU core number ands r0, r0, #15 - moveq r0, #0x10000000 @ SCU_BASE - orreq r0, r0, #0x00100000 + ldreq r0, =SCU_BASE ldreq r5, [r0, #SCU_CTRL] orreq r5, r5, #1 streq r5, [r0, #SCU_CTRL] diff --git a/include/asm-arm/arch-realview/hardware.h b/include/asm-arm/arch-realview/hardware.h index 9ca76dc3a7af..aa78fe087ab2 100644 --- a/include/asm-arm/arch-realview/hardware.h +++ b/include/asm-arm/arch-realview/hardware.h @@ -26,7 +26,7 @@ #include /* macro to get at IO space when running virtually */ -#define IO_ADDRESS(x) (((x) & 0x0fffffff) + (((x) >> 4) & 0x0f000000) + 0xf0000000) +#define IO_ADDRESS(x) ((((x) & 0x0effffff) | (((x) >> 4) & 0x0f000000)) + 0xf0000000) #define __io_address(n) __io(IO_ADDRESS(n)) #endif diff --git a/include/asm-arm/arch-realview/platform.h b/include/asm-arm/arch-realview/platform.h index bf52ca752a75..87acd9c191e6 100644 --- a/include/asm-arm/arch-realview/platform.h +++ b/include/asm-arm/arch-realview/platform.h @@ -207,11 +207,21 @@ #define REALVIEW_GIC_CPU_BASE 0x10040000 /* Generic interrupt controller CPU interface */ #define REALVIEW_GIC_DIST_BASE 0x10041000 /* Generic interrupt controller distributor */ #else +#ifdef CONFIG_REALVIEW_MPCORE_REVB #define REALVIEW_MPCORE_SCU_BASE 0x10100000 /* SCU registers */ #define REALVIEW_GIC_CPU_BASE 0x10100100 /* Generic interrupt controller CPU interface */ #define REALVIEW_TWD_BASE 0x10100700 #define REALVIEW_TWD_SIZE 0x00000100 #define REALVIEW_GIC_DIST_BASE 0x10101000 /* Generic interrupt controller distributor */ +#define REALVIEW_MPCORE_SYS_PLD_CTRL1 0xD8 /* Register offset for MPCore sysctl */ +#else +#define REALVIEW_MPCORE_SCU_BASE 0x1F000000 /* SCU registers */ +#define REALVIEW_GIC_CPU_BASE 0x1F000100 /* Generic interrupt controller CPU interface */ +#define REALVIEW_TWD_BASE 0x1F000700 +#define REALVIEW_TWD_SIZE 0x00000100 +#define REALVIEW_GIC_DIST_BASE 0x1F001000 /* Generic interrupt controller distributor */ +#define REALVIEW_MPCORE_SYS_PLD_CTRL1 0x74 /* Register offset for MPCore sysctl */ +#endif #define REALVIEW_GIC1_CPU_BASE 0x10040000 /* Generic interrupt controller CPU interface */ #define REALVIEW_GIC1_DIST_BASE 0x10041000 /* Generic interrupt controller distributor */ #endif diff --git a/include/asm-arm/arch-realview/scu.h b/include/asm-arm/arch-realview/scu.h new file mode 100644 index 000000000000..cc293640178e --- /dev/null +++ b/include/asm-arm/arch-realview/scu.h @@ -0,0 +1,8 @@ +#ifndef __ASMARM_ARCH_SCU_H +#define __ASMARM_ARCH_SCU_H + +#include + +#define SCU_BASE REALVIEW_MPCORE_SCU_BASE + +#endif diff --git a/include/asm-arm/hardware/arm_scu.h b/include/asm-arm/hardware/arm_scu.h index 9903f60c84b7..7d28eb5a1758 100644 --- a/include/asm-arm/hardware/arm_scu.h +++ b/include/asm-arm/hardware/arm_scu.h @@ -1,6 +1,8 @@ #ifndef ASMARM_HARDWARE_ARM_SCU_H #define ASMARM_HARDWARE_ARM_SCU_H +#include + /* * SCU registers */ -- cgit v1.2.3 From 7770bddb27ea84519486d8bb5d35d36d580c451b Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Mon, 5 Feb 2007 14:48:24 +0100 Subject: [ARM] 4130/1: Add L220 support to RealView/EB This patch enables the L220 on the RealView/EB MPCore platform. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mach-realview/Kconfig | 1 + arch/arm/mach-realview/realview_eb.c | 11 +++++++++++ include/asm-arm/arch-realview/platform.h | 2 ++ 3 files changed, 14 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig index 68bc6b226ec7..35156ca39df7 100644 --- a/arch/arm/mach-realview/Kconfig +++ b/arch/arm/mach-realview/Kconfig @@ -10,6 +10,7 @@ config MACH_REALVIEW_EB config REALVIEW_MPCORE bool "Support MPcore tile" depends on MACH_REALVIEW_EB + select CACHE_L2X0 help Enable support for the MPCore tile on the Realview platform. Since there are device address and interrupt differences, a diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index effe243454e0..3dba666151db 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -31,6 +31,7 @@ #include #include #include +#include #include #include @@ -69,6 +70,11 @@ static struct map_desc realview_eb_io_desc[] __initdata = { .pfn = __phys_to_pfn(REALVIEW_GIC1_DIST_BASE), .length = SZ_4K, .type = MT_DEVICE, + }, { + .virtual = IO_ADDRESS(REALVIEW_MPCORE_L220_BASE), + .pfn = __phys_to_pfn(REALVIEW_MPCORE_L220_BASE), + .length = SZ_8K, + .type = MT_DEVICE, }, #endif { @@ -170,6 +176,11 @@ static void __init realview_eb_init(void) { int i; +#ifdef CONFIG_REALVIEW_MPCORE + /* 1MB (128KB/way), 8-way associativity, evmon/parity/share enabled + * Bits: .... ...0 0111 1001 0000 .... .... .... */ + l2x0_init(__io_address(REALVIEW_MPCORE_L220_BASE), 0x00790000, 0xfe000fff); +#endif clk_register(&realview_clcd_clk); platform_device_register(&realview_flash_device); diff --git a/include/asm-arm/arch-realview/platform.h b/include/asm-arm/arch-realview/platform.h index 87acd9c191e6..6e0eab95a3a2 100644 --- a/include/asm-arm/arch-realview/platform.h +++ b/include/asm-arm/arch-realview/platform.h @@ -213,6 +213,7 @@ #define REALVIEW_TWD_BASE 0x10100700 #define REALVIEW_TWD_SIZE 0x00000100 #define REALVIEW_GIC_DIST_BASE 0x10101000 /* Generic interrupt controller distributor */ +#define REALVIEW_MPCORE_L220_BASE 0x10102000 /* L220 registers */ #define REALVIEW_MPCORE_SYS_PLD_CTRL1 0xD8 /* Register offset for MPCore sysctl */ #else #define REALVIEW_MPCORE_SCU_BASE 0x1F000000 /* SCU registers */ @@ -220,6 +221,7 @@ #define REALVIEW_TWD_BASE 0x1F000700 #define REALVIEW_TWD_SIZE 0x00000100 #define REALVIEW_GIC_DIST_BASE 0x1F001000 /* Generic interrupt controller distributor */ +#define REALVIEW_MPCORE_L220_BASE 0x1F002000 /* L220 registers */ #define REALVIEW_MPCORE_SYS_PLD_CTRL1 0x74 /* Register offset for MPCore sysctl */ #endif #define REALVIEW_GIC1_CPU_BASE 0x10040000 /* Generic interrupt controller CPU interface */ -- cgit v1.2.3 From f7eee89b2a4b4c233acde621005a814da0eb46d6 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Thu, 15 Feb 2007 08:17:38 +0100 Subject: [ARM] 4192/1: AT91: Support for AT91SAM9XE processors. Add support for the Atmel AT91SAM9XE range of processors. These are basically AT91SAM9260's with different amounts of internal SRAM and Flash. We make use of the existing AT91SAM9260 support, but just perform run-time detection of the size of the internal SRAM. Original patch from Nicolas Ferre. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/Kconfig | 17 +++++++++---- arch/arm/mach-at91/at91sam9260.c | 42 +++++++++++++++++++++++++++++++-- include/asm-arm/arch-at91/at91_dbgu.h | 14 +++++++++++ include/asm-arm/arch-at91/at91sam9260.h | 4 ++++ include/asm-arm/arch-at91/cpu.h | 17 ++++++++++++- 5 files changed, 87 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 9313888d77c9..bf0d96272e3a 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -9,7 +9,7 @@ config ARCH_AT91RM9200 bool "AT91RM9200" config ARCH_AT91SAM9260 - bool "AT91SAM9260" + bool "AT91SAM9260 or AT91SAM9XE" config ARCH_AT91SAM9261 bool "AT91SAM9261" @@ -93,13 +93,22 @@ endif if ARCH_AT91SAM9260 -comment "AT91SAM9260 Board Type" +comment "AT91SAM9260 Variants" + +config ARCH_AT91SAM9260_SAM9XE + bool "AT91SAM9XE" + depends on ARCH_AT91SAM9260 + help + Select this if you are using Atmel's AT91SAM9XE System-on-Chip. + They are basicaly AT91SAM9260s with various sizes of embedded Flash. + +comment "AT91SAM9260 / AT91SAM9XE Board Type" config MACH_AT91SAM9260EK - bool "Atmel AT91SAM9260-EK Evaluation Kit" + bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit" depends on ARCH_AT91SAM9260 help - Select this if you are using Atmel's AT91SAM9260-EK Evaluation Kit. + Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit endif diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index 86e3a4c46550..003c27c2ef65 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -14,6 +14,7 @@ #include #include +#include #include #include #include @@ -27,7 +28,11 @@ static struct map_desc at91sam9260_io_desc[] __initdata = { .pfn = __phys_to_pfn(AT91_BASE_SYS), .length = SZ_16K, .type = MT_DEVICE, - }, { + } +}; + +static struct map_desc at91sam9260_sram_desc[] __initdata = { + { .virtual = AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE, .pfn = __phys_to_pfn(AT91SAM9260_SRAM0_BASE), .length = AT91SAM9260_SRAM0_SIZE, @@ -37,7 +42,14 @@ static struct map_desc at91sam9260_io_desc[] __initdata = { .pfn = __phys_to_pfn(AT91SAM9260_SRAM1_BASE), .length = AT91SAM9260_SRAM1_SIZE, .type = MT_DEVICE, - }, + } +}; + +static struct map_desc at91sam9xe_sram_desc[] __initdata = { + { + .pfn = __phys_to_pfn(AT91SAM9XE_SRAM_BASE), + .type = MT_DEVICE, + } }; /* -------------------------------------------------------------------- @@ -255,11 +267,37 @@ static void at91sam9260_reset(void) * AT91SAM9260 processor initialization * -------------------------------------------------------------------- */ +static void __init at91sam9xe_initialize(void) +{ + unsigned long cidr, sram_size; + + cidr = at91_sys_read(AT91_DBGU_CIDR); + + switch (cidr & AT91_CIDR_SRAMSIZ) { + case AT91_CIDR_SRAMSIZ_32K: + sram_size = 2 * SZ_16K; + break; + case AT91_CIDR_SRAMSIZ_16K: + default: + sram_size = SZ_16K; + } + + at91sam9xe_sram_desc->virtual = AT91_IO_VIRT_BASE - sram_size; + at91sam9xe_sram_desc->length = sram_size; + + iotable_init(at91sam9xe_sram_desc, ARRAY_SIZE(at91sam9xe_sram_desc)); +} + void __init at91sam9260_initialize(unsigned long main_clock) { /* Map peripherals */ iotable_init(at91sam9260_io_desc, ARRAY_SIZE(at91sam9260_io_desc)); + if (cpu_is_at91sam9xe()) + at91sam9xe_initialize(); + else + iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc)); + at91_arch_reset = at91sam9260_reset; at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1) | (1 << AT91SAM9260_ID_IRQ2); diff --git a/include/asm-arm/arch-at91/at91_dbgu.h b/include/asm-arm/arch-at91/at91_dbgu.h index 1002a808ad91..b0369e176f7b 100644 --- a/include/asm-arm/arch-at91/at91_dbgu.h +++ b/include/asm-arm/arch-at91/at91_dbgu.h @@ -35,6 +35,20 @@ #define AT91_CIDR_NVPSIZ (0xf << 8) /* Nonvolatile Program Memory Size */ #define AT91_CIDR_NVPSIZ2 (0xf << 12) /* Second Nonvolatile Program Memory Size */ #define AT91_CIDR_SRAMSIZ (0xf << 16) /* Internal SRAM Size */ +#define AT91_CIDR_SRAMSIZ_1K (1 << 16) +#define AT91_CIDR_SRAMSIZ_2K (2 << 16) +#define AT91_CIDR_SRAMSIZ_112K (4 << 16) +#define AT91_CIDR_SRAMSIZ_4K (5 << 16) +#define AT91_CIDR_SRAMSIZ_80K (6 << 16) +#define AT91_CIDR_SRAMSIZ_160K (7 << 16) +#define AT91_CIDR_SRAMSIZ_8K (8 << 16) +#define AT91_CIDR_SRAMSIZ_16K (9 << 16) +#define AT91_CIDR_SRAMSIZ_32K (10 << 16) +#define AT91_CIDR_SRAMSIZ_64K (11 << 16) +#define AT91_CIDR_SRAMSIZ_128K (12 << 16) +#define AT91_CIDR_SRAMSIZ_256K (13 << 16) +#define AT91_CIDR_SRAMSIZ_96K (14 << 16) +#define AT91_CIDR_SRAMSIZ_512K (15 << 16) #define AT91_CIDR_ARCH (0xff << 20) /* Architecture Identifier */ #define AT91_CIDR_NVPTYP (7 << 28) /* Nonvolatile Program Memory Type */ #define AT91_CIDR_EXT (1 << 31) /* Extension Flag */ diff --git a/include/asm-arm/arch-at91/at91sam9260.h b/include/asm-arm/arch-at91/at91sam9260.h index 73d93ae9243e..2cadebc36af7 100644 --- a/include/asm-arm/arch-at91/at91sam9260.h +++ b/include/asm-arm/arch-at91/at91sam9260.h @@ -113,6 +113,10 @@ #define AT91SAM9260_UHP_BASE 0x00500000 /* USB Host controller */ +#define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */ +#define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */ + + #if 0 /* * PIO pin definitions (peripheral A/B multiplexing). diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h index 9efde0dad249..d464ca58cdbc 100644 --- a/include/asm-arm/arch-at91/cpu.h +++ b/include/asm-arm/arch-at91/cpu.h @@ -22,6 +22,9 @@ #define ARCH_ID_AT91SAM9261 0x019703a0 #define ARCH_ID_AT91SAM9263 0x019607a0 +#define ARCH_ID_AT91SAM9XE128 0x329973a0 +#define ARCH_ID_AT91SAM9XE256 0x329a93a0 +#define ARCH_ID_AT91SAM9XE512 0x329aa3a0 static inline unsigned long at91_cpu_identify(void) { @@ -29,6 +32,16 @@ static inline unsigned long at91_cpu_identify(void) } +#define ARCH_FAMILY_AT91X92 0x09200000 +#define ARCH_FAMILY_AT91SAM9 0x01900000 +#define ARCH_FAMILY_AT91SAM9XE 0x02900000 + +static inline unsigned long at91_arch_identify(void) +{ + return (at91_sys_read(AT91_DBGU_CIDR) & AT91_CIDR_ARCH); +} + + #ifdef CONFIG_ARCH_AT91RM9200 #define cpu_is_at91rm9200() (at91_cpu_identify() == ARCH_ID_AT91RM9200) #else @@ -36,8 +49,10 @@ static inline unsigned long at91_cpu_identify(void) #endif #ifdef CONFIG_ARCH_AT91SAM9260 -#define cpu_is_at91sam9260() (at91_cpu_identify() == ARCH_ID_AT91SAM9260) +#define cpu_is_at91sam9xe() (at91_arch_identify() == ARCH_FAMILY_AT91SAM9XE) +#define cpu_is_at91sam9260() ((at91_cpu_identify() == ARCH_ID_AT91SAM9260) || cpu_is_at91sam9xe()) #else +#define cpu_is_at91sam9xe() (0) #define cpu_is_at91sam9260() (0) #endif -- cgit v1.2.3 From e4d06e39530559513c7e335ef7ca4675f8146220 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 16 Feb 2007 12:12:31 +0100 Subject: [ARM] 4198/2: S3C2443: arch/arm/mach-s3c2443 and related support Add arch/arm/mach-s3c2443 for support of the Samsung S3C2443 SoC This patch adds the core CPU support, clock framework, times and initial IRQ support, as well as adding the directory into the build tree. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/Kconfig | 3 +- arch/arm/Makefile | 1 + arch/arm/mach-s3c2443/Kconfig | 18 + arch/arm/mach-s3c2443/Makefile | 16 + arch/arm/mach-s3c2443/clock.c | 1007 ++++++++++++++++++++++++++++++++ arch/arm/mach-s3c2443/irq.c | 130 +++++ arch/arm/mach-s3c2443/s3c2443.c | 87 +++ arch/arm/plat-s3c24xx/cpu.c | 11 + arch/arm/plat-s3c24xx/s3c244x.c | 2 +- include/asm-arm/plat-s3c24xx/cpu.h | 1 + include/asm-arm/plat-s3c24xx/s3c2443.h | 32 + 11 files changed, 1306 insertions(+), 2 deletions(-) create mode 100644 arch/arm/mach-s3c2443/Kconfig create mode 100644 arch/arm/mach-s3c2443/Makefile create mode 100644 arch/arm/mach-s3c2443/clock.c create mode 100644 arch/arm/mach-s3c2443/irq.c create mode 100644 arch/arm/mach-s3c2443/s3c2443.c create mode 100644 include/asm-arm/plat-s3c24xx/s3c2443.h (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 51ee13e7c74c..0f711c4394a9 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -303,7 +303,7 @@ config ARCH_SA1100 Support for StrongARM 11x0 based boards. config ARCH_S3C2410 - bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442" + bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443" help Samsung S3C2410X CPU based systems, such as the Simtec Electronics BAST (), the IPAQ 1940 or @@ -371,6 +371,7 @@ source "arch/arm/mach-s3c2410/Kconfig" source "arch/arm/mach-s3c2412/Kconfig" source "arch/arm/mach-s3c2440/Kconfig" source "arch/arm/mach-s3c2442/Kconfig" +source "arch/arm/mach-s3c2443/Kconfig" endif source "arch/arm/mach-lh7a40x/Kconfig" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 2df1ea0a0c2d..93e474726725 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -165,6 +165,7 @@ core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2400/ core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2412/ core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2440/ core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2442/ +core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2443/ core-$(CONFIG_FPE_NWFPE) += arch/arm/nwfpe/ core-$(CONFIG_FPE_FASTFPE) += $(FASTFPE_OBJ) core-$(CONFIG_VFP) += arch/arm/vfp/ diff --git a/arch/arm/mach-s3c2443/Kconfig b/arch/arm/mach-s3c2443/Kconfig new file mode 100644 index 000000000000..0d8d7bf9a96b --- /dev/null +++ b/arch/arm/mach-s3c2443/Kconfig @@ -0,0 +1,18 @@ +# arch/arm/mach-s3c2443/Kconfig +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +config CPU_S3C2443 + bool + depends on ARCH_S3C2410 + select S3C2443_PM if PM + select S3C2443_DMA if S3C2410_DMA + help + Support for the S3C2443 SoC from the S3C24XX line + +menu "S3C2443 Machines" + +endmenu + diff --git a/arch/arm/mach-s3c2443/Makefile b/arch/arm/mach-s3c2443/Makefile new file mode 100644 index 000000000000..397475affbe1 --- /dev/null +++ b/arch/arm/mach-s3c2443/Makefile @@ -0,0 +1,16 @@ +# arch/arm/mach-s3c2443/Makefile +# +# Copyright 2007 Simtec Electronics +# +# Licensed under GPLv2 + +obj-y := +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_CPU_S3C2443) += s3c2443.o +obj-$(CONFIG_CPU_S3C2443) += irq.o +obj-$(CONFIG_CPU_S3C2443) += clock.o + +# Machine support diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c new file mode 100644 index 000000000000..dd2272fb1131 --- /dev/null +++ b/arch/arm/mach-s3c2443/clock.c @@ -0,0 +1,1007 @@ +/* linux/arch/arm/mach-s3c2443/clock.c + * + * Copyright (c) 2007 Simtec Electronics + * Ben Dooks + * + * S3C2443 Clock control support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include + +#include + +#include +#include +#include + +/* We currently have to assume that the system is running + * from the XTPll input, and that all ***REFCLKs are being + * fed from it, as we cannot read the state of OM[4] from + * software. + * + * It would be possible for each board initialisation to + * set the correct muxing at initialisation +*/ + +static int s3c2443_clkcon_enable_h(struct clk *clk, int enable) +{ + unsigned int clocks = clk->ctrlbit; + unsigned long clkcon; + + clkcon = __raw_readl(S3C2443_HCLKCON); + + if (enable) + clkcon |= clocks; + else + clkcon &= ~clocks; + + __raw_writel(clkcon, S3C2443_HCLKCON); + + return 0; +} + +static int s3c2443_clkcon_enable_p(struct clk *clk, int enable) +{ + unsigned int clocks = clk->ctrlbit; + unsigned long clkcon; + + clkcon = __raw_readl(S3C2443_PCLKCON); + + if (enable) + clkcon |= clocks; + else + clkcon &= ~clocks; + + __raw_writel(clkcon, S3C2443_HCLKCON); + + return 0; +} + +static int s3c2443_clkcon_enable_s(struct clk *clk, int enable) +{ + unsigned int clocks = clk->ctrlbit; + unsigned long clkcon; + + clkcon = __raw_readl(S3C2443_SCLKCON); + + if (enable) + clkcon |= clocks; + else + clkcon &= ~clocks; + + __raw_writel(clkcon, S3C2443_SCLKCON); + + return 0; +} + +static unsigned long s3c2443_roundrate_clksrc(struct clk *clk, + unsigned long rate, + unsigned int max) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + int div; + + if (rate > parent_rate) + return parent_rate; + + /* note, we remove the +/- 1 calculations as they cancel out */ + + div = (rate / parent_rate); + + if (div < 1) + div = 1; + else if (div > max) + div = max; + + return parent_rate / div; +} + +static unsigned long s3c2443_roundrate_clksrc4(struct clk *clk, + unsigned long rate) +{ + return s3c2443_roundrate_clksrc(clk, rate, 4); +} + +static unsigned long s3c2443_roundrate_clksrc16(struct clk *clk, + unsigned long rate) +{ + return s3c2443_roundrate_clksrc(clk, rate, 16); +} + +static unsigned long s3c2443_roundrate_clksrc256(struct clk *clk, + unsigned long rate) +{ + return s3c2443_roundrate_clksrc(clk, rate, 256); +} + +/* clock selections */ + +/* CPU EXTCLK input */ +static struct clk clk_ext = { + .name = "ext", + .id = -1, +}; + +static struct clk clk_mpllref = { + .name = "mpllref", + .parent = &clk_xtal, + .id = -1, +}; + +#if 0 +static struct clk clk_mpll = { + .name = "mpll", + .parent = &clk_mpllref, + .id = -1, +}; +#endif + +static struct clk clk_epllref; + +static struct clk clk_epll = { + .name = "epll", + .parent = &clk_epllref, + .id = -1, +}; + +static struct clk clk_i2s_ext = { + .name = "i2s-ext", + .id = -1, +}; + +static int s3c2443_setparent_epllref(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2443_CLKSRC); + + clksrc &= ~S3C2443_CLKSRC_EPLLREF_MASK; + + if (parent == &clk_xtal) + clksrc |= S3C2443_CLKSRC_EPLLREF_XTAL; + else if (parent == &clk_ext) + clksrc |= S3C2443_CLKSRC_EPLLREF_EXTCLK; + else if (parent != &clk_mpllref) + return -EINVAL; + + __raw_writel(clksrc, S3C2443_CLKSRC); + clk->parent = parent; + + return 0; +} + +static struct clk clk_epllref = { + .name = "epllref", + .id = -1, + .set_parent = s3c2443_setparent_epllref, +}; + +static unsigned long s3c2443_getrate_mdivclk(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV0); + + div &= S3C2443_CLKDIV0_EXTDIV_MASK; + div >>= (S3C2443_CLKDIV0_EXTDIV_SHIFT-1); /* x2 */ + + return parent_rate / (div + 1); +} + +static struct clk clk_mdivclk = { + .name = "mdivclk", + .parent = &clk_mpllref, + .id = -1, + .get_rate = s3c2443_getrate_mdivclk, +}; + + +static int s3c2443_setparent_msysclk(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2443_CLKSRC); + + clksrc &= ~(S3C2443_CLKSRC_MSYSCLK_MPLL | + S3C2443_CLKSRC_EXTCLK_DIV); + + if (parent == &clk_mpll) + clksrc |= S3C2443_CLKSRC_MSYSCLK_MPLL; + else if (parent == &clk_mdivclk) + clksrc |= S3C2443_CLKSRC_EXTCLK_DIV; + else if (parent != &clk_mpllref) + return -EINVAL; + + __raw_writel(clksrc, S3C2443_CLKSRC); + clk->parent = parent; + + return 0; +} + +static struct clk clk_msysclk = { + .name = "msysclk", + .parent = &clk_xtal, + .id = -1, + .set_parent = s3c2443_setparent_msysclk, +}; + + +/* esysclk + * + * this is sourced from either the EPLL or the EPLLref clock +*/ + +static int s3c2443_setparent_esysclk(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2443_CLKSRC); + + if (parent == &clk_epll) + clksrc |= S3C2443_CLKSRC_ESYSCLK_EPLL; + else if (parent == &clk_epllref) + clksrc &= ~S3C2443_CLKSRC_ESYSCLK_EPLL; + else + return -EINVAL; + + __raw_writel(clksrc, S3C2443_CLKSRC); + clk->parent = parent; + + return 0; +} + +static struct clk clk_esysclk = { + .name = "esysclk", + .parent = &clk_epll, + .id = -1, + .set_parent = s3c2443_setparent_esysclk, +}; + +/* uartclk + * + * UART baud-rate clock sourced from esysclk via a divisor +*/ + +static unsigned long s3c2443_getrate_uart(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_UARTDIV_MASK; + div >>= S3C2443_CLKDIV1_UARTDIV_SHIFT; + + return parent_rate / (div + 1); +} + + +static int s3c2443_setrate_uart(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc16(clk, rate); + rate = parent_rate / rate; + + clkdivn &= ~S3C2443_CLKDIV1_UARTDIV_MASK; + clkdivn |= (rate - 1) << S3C2443_CLKDIV1_UARTDIV_SHIFT; + + __raw_writel(clkdivn, S3C2443_CLKDIV1); + return 0; +} + +static struct clk clk_uart = { + .name = "uartclk", + .id = -1, + .parent = &clk_esysclk, + .get_rate = s3c2443_getrate_uart, + .set_rate = s3c2443_setrate_uart, + .round_rate = s3c2443_roundrate_clksrc16, +}; + +/* hsspi + * + * high-speed spi clock, sourced from esysclk +*/ + +static unsigned long s3c2443_getrate_hsspi(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_HSSPIDIV_MASK; + div >>= S3C2443_CLKDIV1_HSSPIDIV_SHIFT; + + return parent_rate / (div + 1); +} + + +static int s3c2443_setrate_hsspi(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc4(clk, rate); + rate = parent_rate / rate; + + clkdivn &= ~S3C2443_CLKDIV1_HSSPIDIV_MASK; + clkdivn |= (rate - 1) << S3C2443_CLKDIV1_HSSPIDIV_SHIFT; + + __raw_writel(clkdivn, S3C2443_CLKDIV1); + return 0; +} + +static struct clk clk_hsspi = { + .name = "hsspi", + .id = -1, + .parent = &clk_esysclk, + .ctrlbit = S3C2443_SCLKCON_HSSPICLK, + .enable = s3c2443_clkcon_enable_s, + .get_rate = s3c2443_getrate_hsspi, + .set_rate = s3c2443_setrate_hsspi, + .round_rate = s3c2443_roundrate_clksrc4, +}; + +/* usbhost + * + * usb host bus-clock, usually 48MHz to provide USB bus clock timing +*/ + +static unsigned long s3c2443_getrate_usbhost(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_USBHOSTDIV_MASK; + div >>= S3C2443_CLKDIV1_USBHOSTDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2443_setrate_usbhost(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc4(clk, rate); + rate = parent_rate / rate; + + clkdivn &= ~S3C2443_CLKDIV1_USBHOSTDIV_MASK; + clkdivn |= (rate - 1) << S3C2443_CLKDIV1_USBHOSTDIV_SHIFT; + + __raw_writel(clkdivn, S3C2443_CLKDIV1); + return 0; +} + +struct clk clk_usb_bus_host = { + .name = "usb-bus-host-parent", + .id = -1, + .parent = &clk_esysclk, + .ctrlbit = S3C2443_SCLKCON_USBHOST, + .enable = s3c2443_clkcon_enable_s, + .get_rate = s3c2443_getrate_usbhost, + .set_rate = s3c2443_setrate_usbhost, + .round_rate = s3c2443_roundrate_clksrc4, +}; + +/* clk_hsmcc_div + * + * this clock is sourced from epll, and is fed through a divider, + * to a mux controlled by sclkcon where either it or a extclk can + * be fed to the hsmmc block +*/ + +static unsigned long s3c2443_getrate_hsmmc_div(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_HSMMCDIV_MASK; + div >>= S3C2443_CLKDIV1_HSMMCDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2443_setrate_hsmmc_div(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc4(clk, rate); + rate = parent_rate / rate; + + clkdivn &= ~S3C2443_CLKDIV1_HSMMCDIV_MASK; + clkdivn |= (rate - 1) << S3C2443_CLKDIV1_HSMMCDIV_SHIFT; + + __raw_writel(clkdivn, S3C2443_CLKDIV1); + return 0; +} + +static struct clk clk_hsmmc_div = { + .name = "hsmmc-div", + .id = -1, + .parent = &clk_esysclk, + .get_rate = s3c2443_getrate_hsmmc_div, + .set_rate = s3c2443_setrate_hsmmc_div, + .round_rate = s3c2443_roundrate_clksrc4, +}; + +static int s3c2443_setparent_hsmmc(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2443_SCLKCON); + + clksrc &= ~(S3C2443_SCLKCON_HSMMCCLK_EXT | + S3C2443_SCLKCON_HSMMCCLK_EPLL); + + if (parent == &clk_epll) + clksrc |= S3C2443_SCLKCON_HSMMCCLK_EPLL; + else if (parent == &clk_ext) + clksrc |= S3C2443_SCLKCON_HSMMCCLK_EXT; + else + return -EINVAL; + + if (clk->usage > 0) { + __raw_writel(clksrc, S3C2443_SCLKCON); + } + + clk->parent = parent; + return 0; +} + +static int s3c2443_enable_hsmmc(struct clk *clk, int enable) +{ + return s3c2443_setparent_hsmmc(clk, clk->parent); +} + +static struct clk clk_hsmmc = { + .name = "hsmmc-if", + .id = -1, + .parent = &clk_hsmmc_div, + .enable = s3c2443_enable_hsmmc, + .set_parent = s3c2443_setparent_hsmmc, +}; + +/* i2s_eplldiv + * + * this clock is the output from the i2s divisor of esysclk +*/ + +static unsigned long s3c2443_getrate_i2s_eplldiv(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_I2SDIV_MASK; + div >>= S3C2443_CLKDIV1_I2SDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2443_setrate_i2s_eplldiv(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc16(clk, rate); + rate = parent_rate / rate; + + clkdivn &= ~S3C2443_CLKDIV1_I2SDIV_MASK; + clkdivn |= (rate - 1) << S3C2443_CLKDIV1_I2SDIV_SHIFT; + + __raw_writel(clkdivn, S3C2443_CLKDIV1); + return 0; +} + +static struct clk clk_i2s_eplldiv = { + .name = "i2s-eplldiv", + .id = -1, + .parent = &clk_esysclk, + .get_rate = s3c2443_getrate_i2s_eplldiv, + .set_rate = s3c2443_setrate_i2s_eplldiv, + .round_rate = s3c2443_roundrate_clksrc16, +}; + +/* i2s-ref + * + * i2s bus reference clock, selectable from external, esysclk or epllref +*/ + +static int s3c2443_setparent_i2s(struct clk *clk, struct clk *parent) +{ + unsigned long clksrc = __raw_readl(S3C2443_CLKSRC); + + clksrc &= ~S3C2443_CLKSRC_I2S_MASK; + + if (parent == &clk_epllref) + clksrc |= S3C2443_CLKSRC_I2S_EPLLREF; + else if (parent == &clk_i2s_ext) + clksrc |= S3C2443_CLKSRC_I2S_EXT; + else if (parent != &clk_i2s_eplldiv) + return -EINVAL; + + clk->parent = parent; + __raw_writel(clksrc, S3C2443_CLKSRC); + + return 0; +} + +static struct clk clk_i2s = { + .name = "i2s-if", + .id = -1, + .parent = &clk_i2s_eplldiv, + .ctrlbit = S3C2443_SCLKCON_I2SCLK, + .enable = s3c2443_clkcon_enable_s, + .set_parent = s3c2443_setparent_i2s, +}; + +/* cam-if + * + * camera interface bus-clock, divided down from esysclk +*/ + +static unsigned long s3c2443_getrate_cam(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_CAMDIV_MASK; + div >>= S3C2443_CLKDIV1_CAMDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2443_setrate_cam(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdiv1 = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc16(clk, rate); + rate = parent_rate / rate; + + clkdiv1 &= ~S3C2443_CLKDIV1_CAMDIV_MASK; + clkdiv1 |= (rate - 1) << S3C2443_CLKDIV1_CAMDIV_SHIFT; + + __raw_writel(clkdiv1, S3C2443_CLKDIV1); + return 0; +} + +static struct clk clk_cam = { + .name = "camif-upll", /* same as 2440 name */ + .id = -1, + .parent = &clk_esysclk, + .ctrlbit = S3C2443_SCLKCON_CAMCLK, + .enable = s3c2443_clkcon_enable_s, + .get_rate = s3c2443_getrate_cam, + .set_rate = s3c2443_setrate_cam, + .round_rate = s3c2443_roundrate_clksrc16, +}; + +/* display-if + * + * display interface clock, divided from esysclk +*/ + +static unsigned long s3c2443_getrate_display(struct clk *clk) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long div = __raw_readl(S3C2443_CLKDIV1); + + div &= S3C2443_CLKDIV1_DISPDIV_MASK; + div >>= S3C2443_CLKDIV1_DISPDIV_SHIFT; + + return parent_rate / (div + 1); +} + +static int s3c2443_setrate_display(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1); + + rate = s3c2443_roundrate_clksrc256(clk, rate); + rate = parent_rate / rate; + + clkdivn &= ~S3C2443_CLKDIV1_UARTDIV_MASK; + clkdivn |= (rate - 1) << S3C2443_CLKDIV1_UARTDIV_SHIFT; + + __raw_writel(clkdivn, S3C2443_CLKDIV1); + return 0; +} + +static struct clk clk_display = { + .name = "display-if", + .id = -1, + .parent = &clk_esysclk, + .ctrlbit = S3C2443_SCLKCON_DISPCLK, + .enable = s3c2443_clkcon_enable_s, + .get_rate = s3c2443_getrate_display, + .set_rate = s3c2443_setrate_display, + .round_rate = s3c2443_roundrate_clksrc256, +}; + +/* standard clock definitions */ + +static struct clk init_clocks_disable[] = { + { + .name = "nand", + .id = -1, + .parent = &clk_h, + }, { + .name = "sdi", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_SDI, + }, { + .name = "adc", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_ADC, + }, { + .name = "i2c", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_IIC, + }, { + .name = "iis", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_IIS, + }, { + .name = "spi", + .id = 0, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_SPI0, + }, { + .name = "spi", + .id = 1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_SPI1, + } +}; + +static struct clk init_clocks[] = { + { + .name = "dma", + .id = 0, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_DMA0, + }, { + .name = "dma", + .id = 1, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_DMA1, + }, { + .name = "dma", + .id = 2, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_DMA2, + }, { + .name = "dma", + .id = 3, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_DMA3, + }, { + .name = "dma", + .id = 4, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_DMA4, + }, { + .name = "dma", + .id = 5, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_DMA5, + }, { + .name = "lcd", + .id = -1, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_LCDC, + }, { + .name = "gpio", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_GPIO, + }, { + .name = "usb-host", + .id = -1, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_USBH, + }, { + .name = "usb-device", + .id = -1, + .parent = &clk_h, + .enable = s3c2443_clkcon_enable_h, + .ctrlbit = S3C2443_HCLKCON_USBD, + }, { + .name = "timers", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_PWMT, + }, { + .name = "uart", + .id = 0, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_UART0, + }, { + .name = "uart", + .id = 1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_UART1, + }, { + .name = "uart", + .id = 2, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_UART2, + }, { + .name = "uart", + .id = 3, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_UART3, + }, { + .name = "rtc", + .id = -1, + .parent = &clk_p, + .enable = s3c2443_clkcon_enable_p, + .ctrlbit = S3C2443_PCLKCON_RTC, + }, { + .name = "watchdog", + .id = -1, + .parent = &clk_p, + .ctrlbit = S3C2443_PCLKCON_WDT, + }, { + .name = "usb-bus-host", + .id = -1, + .parent = &clk_usb_bus_host, + } +}; + +/* clocks to add where we need to check their parentage */ + +/* s3c2443_clk_initparents + * + * Initialise the parents for the clocks that we get at start-time +*/ + +static int __init clk_init_set_parent(struct clk *clk, struct clk *parent) +{ + printk(KERN_DEBUG "clock %s: parent %s\n", clk->name, parent->name); + return clk_set_parent(clk, parent); +} + +static void __init s3c2443_clk_initparents(void) +{ + unsigned long clksrc = __raw_readl(S3C2443_CLKSRC); + struct clk *parent; + + switch (clksrc & S3C2443_CLKSRC_EPLLREF_MASK) { + case S3C2443_CLKSRC_EPLLREF_EXTCLK: + parent = &clk_ext; + break; + + case S3C2443_CLKSRC_EPLLREF_XTAL: + default: + parent = &clk_xtal; + break; + + case S3C2443_CLKSRC_EPLLREF_MPLLREF: + case S3C2443_CLKSRC_EPLLREF_MPLLREF2: + parent = &clk_mpllref; + break; + } + + clk_init_set_parent(&clk_epllref, parent); + + switch (clksrc & S3C2443_CLKSRC_I2S_MASK) { + case S3C2443_CLKSRC_I2S_EXT: + parent = &clk_i2s_ext; + break; + + case S3C2443_CLKSRC_I2S_EPLLDIV: + default: + parent = &clk_i2s_eplldiv; + break; + + case S3C2443_CLKSRC_I2S_EPLLREF: + case S3C2443_CLKSRC_I2S_EPLLREF3: + parent = &clk_epllref; + } + + clk_init_set_parent(&clk_i2s, &clk_epllref); + + /* esysclk source */ + + parent = (clksrc & S3C2443_CLKSRC_ESYSCLK_EPLL) ? + &clk_epll : &clk_epllref; + + clk_init_set_parent(&clk_esysclk, parent); + + /* msysclk source */ + + if (clksrc & S3C2443_CLKSRC_MSYSCLK_MPLL) { + parent = &clk_mpll; + } else { + parent = (clksrc & S3C2443_CLKSRC_EXTCLK_DIV) ? + &clk_mdivclk : &clk_mpllref; + } + + clk_init_set_parent(&clk_msysclk, parent); +} + +/* armdiv divisor table */ + +static unsigned int armdiv[16] = { + [S3C2443_CLKDIV0_ARMDIV_1 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 1, + [S3C2443_CLKDIV0_ARMDIV_2 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 2, + [S3C2443_CLKDIV0_ARMDIV_3 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 3, + [S3C2443_CLKDIV0_ARMDIV_4 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 4, + [S3C2443_CLKDIV0_ARMDIV_6 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 6, + [S3C2443_CLKDIV0_ARMDIV_8 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 8, + [S3C2443_CLKDIV0_ARMDIV_12 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 12, + [S3C2443_CLKDIV0_ARMDIV_16 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 16, +}; + +static inline unsigned int s3c2443_fclk_div(unsigned long clkcon0) +{ + clkcon0 &= S3C2443_CLKDIV0_ARMDIV_MASK; + + return armdiv[clkcon0 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]; +} + +static inline unsigned long s3c2443_get_prediv(unsigned long clkcon0) +{ + clkcon0 &= S3C2443_CLKDIV0_PREDIV_MASK; + clkcon0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT; + + return clkcon0 + 1; +} + +/* clocks to add straight away */ + +static struct clk *clks[] __initdata = { + &clk_ext, + &clk_epll, + &clk_usb_bus_host, + &clk_usb_bus, + &clk_esysclk, + &clk_epllref, + &clk_mpllref, + &clk_msysclk, + &clk_uart, + &clk_display, + &clk_cam, + &clk_i2s_eplldiv, + &clk_i2s, + &clk_hsspi, + &clk_hsmmc_div, + &clk_hsmmc, +}; + +void __init s3c2443_init_clocks(int xtal) +{ + unsigned long epllcon = __raw_readl(S3C2443_EPLLCON); + unsigned long mpllcon = __raw_readl(S3C2443_MPLLCON); + unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0); + unsigned long pll; + unsigned long fclk; + unsigned long hclk; + unsigned long pclk; + struct clk *clkp; + int ret; + int ptr; + + pll = s3c2443_get_mpll(mpllcon, xtal); + + fclk = pll / s3c2443_fclk_div(clkdiv0); + hclk = fclk / s3c2443_get_prediv(clkdiv0); + hclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_HCLK) ? 2 : 1); + pclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_PCLK) ? 2 : 1); + + s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); + + printk("S3C2443: mpll %s %ld.%03ld MHz, cpu %ld.%03ld MHz, mem %ld.%03ld MHz, pclk %ld.%03ld MHz\n", + (mpllcon & S3C2443_PLLCON_OFF) ? "off":"on", + print_mhz(pll), print_mhz(fclk), + print_mhz(hclk), print_mhz(pclk)); + + s3c2443_clk_initparents(); + + for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) { + clkp = clks[ptr]; + + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + } + + clk_epll.rate = s3c2443_get_epll(epllcon, xtal); + + clk_usb_bus.parent = &clk_usb_bus_host; + + /* ensure usb bus clock is within correct rate of 48MHz */ + + if (clk_get_rate(&clk_usb_bus_host) != (48 * 1000 * 1000)) { + printk(KERN_INFO "Warning: USB host bus not at 48MHz\n"); + clk_set_rate(&clk_usb_bus_host, 48*1000*1000); + } + + printk("S3C2443: epll %s %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n", + (epllcon & S3C2443_PLLCON_OFF) ? "off":"on", + print_mhz(clk_get_rate(&clk_epll)), + print_mhz(clk_get_rate(&clk_usb_bus))); + + /* register clocks from clock array */ + + clkp = init_clocks; + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + } + + /* We must be careful disabling the clocks we are not intending to + * be using at boot time, as subsytems such as the LCD which do + * their own DMA requests to the bus can cause the system to lockup + * if they where in the middle of requesting bus access. + * + * Disabling the LCD clock if the LCD is active is very dangerous, + * and therefore the bootloader should be careful to not enable + * the LCD clock if it is not needed. + */ + + /* install (and disable) the clocks we do not need immediately */ + + clkp = init_clocks_disable; + for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) { + + ret = s3c24xx_register_clock(clkp); + if (ret < 0) { + printk(KERN_ERR "Failed to register clock %s (%d)\n", + clkp->name, ret); + } + + (clkp->enable)(clkp, 0); + } +} diff --git a/arch/arm/mach-s3c2443/irq.c b/arch/arm/mach-s3c2443/irq.c new file mode 100644 index 000000000000..f7058823a0e1 --- /dev/null +++ b/arch/arm/mach-s3c2443/irq.c @@ -0,0 +1,130 @@ +/* linux/arch/arm/mach-s3c2443/irq.c + * + * Copyright (c) 2007 Simtec Electronics + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * +*/ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include + +#include +#include +#include + +/* WDT/AC97 */ + +static void s3c_irq_demux_wdtac97(unsigned int irq, + struct irq_desc *desc) +{ + unsigned int subsrc, submsk; + struct irq_desc *mydesc; + + /* read the current pending interrupts, and the mask + * for what it is available */ + + subsrc = __raw_readl(S3C2410_SUBSRCPND); + submsk = __raw_readl(S3C2410_INTSUBMSK); + + subsrc &= ~submsk; + subsrc >>= 27; + subsrc &= 3; + + if (subsrc != 0) { + if (subsrc & 1) { + mydesc = irq_desc + IRQ_S3C2443_WDT; + desc_handle_irq(IRQ_S3C2443_WDT, mydesc); + } + if (subsrc & 2) { + mydesc = irq_desc + IRQ_S3C2443_AC97; + desc_handle_irq(IRQ_S3C2443_AC97, mydesc); + } + } +} + + +#define INTMSK_WDT (1UL << (IRQ_WDT - IRQ_EINT0)) + +static void +s3c_irq_wdtac97_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_WDT, 3<<27); +} + +static void +s3c_irq_wdtac97_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_WDT); +} + +static void +s3c_irq_wdtac97_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_WDT, 3<<27); +} + +static struct irq_chip s3c_irq_wdtac97 = { + .mask = s3c_irq_wdtac97_mask, + .unmask = s3c_irq_wdtac97_unmask, + .ack = s3c_irq_wdtac97_ack, +}; + +static int s3c2443_irq_add(struct sys_device *sysdev) +{ + unsigned int irqno; + + printk("S3C2443: IRQ Support\n"); + + /* add new chained handler for wdt, ac7 */ + + set_irq_chip(IRQ_WDT, &s3c_irq_level_chip); + set_irq_handler(IRQ_WDT, handle_level_irq); + set_irq_chained_handler(IRQ_WDT, s3c_irq_demux_wdtac97); + + for (irqno = IRQ_S3C2443_WDT; irqno <= IRQ_S3C2443_AC97; irqno++) { + set_irq_chip(irqno, &s3c_irq_wdtac97); + set_irq_handler(irqno, handle_level_irq); + set_irq_flags(irqno, IRQF_VALID); + } + + return 0; +} + +static struct sysdev_driver s3c2443_irq_driver = { + .add = s3c2443_irq_add, +}; + +static int s3c2443_irq_init(void) +{ + return sysdev_driver_register(&s3c2443_sysclass, &s3c2443_irq_driver); +} + +arch_initcall(s3c2443_irq_init); + diff --git a/arch/arm/mach-s3c2443/s3c2443.c b/arch/arm/mach-s3c2443/s3c2443.c new file mode 100644 index 000000000000..bc14f772ff24 --- /dev/null +++ b/arch/arm/mach-s3c2443/s3c2443.c @@ -0,0 +1,87 @@ +/* linux/arch/arm/mach-s3c2443/s3c2443.c + * + * Copyright (c) 2007 Simtec Electronics + * Ben Dooks + * + * Samsung S3C2443 Mobile CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include + +#include +#include +#include + +static struct map_desc s3c2443_iodesc[] __initdata = { + IODESC_ENT(WATCHDOG), + IODESC_ENT(CLKPWR), + IODESC_ENT(TIMER), +}; + +struct sysdev_class s3c2443_sysclass = { + set_kset_name("s3c2443-core"), +}; + +static struct sys_device s3c2443_sysdev = { + .cls = &s3c2443_sysclass, +}; + +int __init s3c2443_init(void) +{ + printk("S3C2443: Initialising architecture\n"); + + return sysdev_register(&s3c2443_sysdev); +} + +void __init s3c2443_init_uarts(struct s3c2410_uartcfg *cfg, int no) +{ + s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no); +} + +/* s3c2443_map_io + * + * register the standard cpu IO areas, and any passed in from the + * machine specific initialisation. + */ + +void __init s3c2443_map_io(struct map_desc *mach_desc, int mach_size) +{ + iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc)); + iotable_init(mach_desc, mach_size); +} + +/* need to register class before we actually register the device, and + * we also need to ensure that it has been initialised before any of the + * drivers even try to use it (even if not on an s3c2443 based system) + * as a driver which may support both 2443 and 2440 may try and use it. +*/ + +static int __init s3c2443_core_init(void) +{ + return sysdev_class_register(&s3c2443_sysclass); +} + +core_initcall(s3c2443_core_init); diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c index 2fbb74969379..6a2d1070e5a0 100644 --- a/arch/arm/plat-s3c24xx/cpu.c +++ b/arch/arm/plat-s3c24xx/cpu.c @@ -49,6 +49,7 @@ #include "s3c244x.h" #include #include +#include struct cpu_table { unsigned long idcode; @@ -67,6 +68,7 @@ static const char name_s3c2410[] = "S3C2410"; static const char name_s3c2412[] = "S3C2412"; static const char name_s3c2440[] = "S3C2440"; static const char name_s3c2442[] = "S3C2442"; +static const char name_s3c2443[] = "S3C2443"; static const char name_s3c2410a[] = "S3C2410A"; static const char name_s3c2440a[] = "S3C2440A"; @@ -134,6 +136,15 @@ static struct cpu_table cpu_ids[] __initdata = { .init = s3c2412_init, .name = name_s3c2412, }, + { + .idcode = 0x32443001, + .idmask = 0xffffffff, + .map_io = s3c2443_map_io, + .init_clocks = s3c2443_init_clocks, + .init_uarts = s3c2443_init_uarts, + .init = s3c2443_init, + .name = name_s3c2443, + }, { .idcode = 0x0, /* S3C2400 doesn't have an idcode */ .idmask = 0xffffffff, diff --git a/arch/arm/plat-s3c24xx/s3c244x.c b/arch/arm/plat-s3c24xx/s3c244x.c index 87aace4c8f8c..767f2e9a3a55 100644 --- a/arch/arm/plat-s3c24xx/s3c244x.c +++ b/arch/arm/plat-s3c24xx/s3c244x.c @@ -3,7 +3,7 @@ * Copyright (c) 2004-2006 Simtec Electronics * Ben Dooks * - * Samsung S3C2440 and S3C2442 Mobile CPU support + * Samsung S3C2440 and S3C2442 Mobile CPU support (not S3C2443) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as diff --git a/include/asm-arm/plat-s3c24xx/cpu.h b/include/asm-arm/plat-s3c24xx/cpu.h index 8181b22532bd..15dd18810905 100644 --- a/include/asm-arm/plat-s3c24xx/cpu.h +++ b/include/asm-arm/plat-s3c24xx/cpu.h @@ -67,3 +67,4 @@ extern struct sysdev_class s3c2410_sysclass; extern struct sysdev_class s3c2412_sysclass; extern struct sysdev_class s3c2440_sysclass; extern struct sysdev_class s3c2442_sysclass; +extern struct sysdev_class s3c2443_sysclass; diff --git a/include/asm-arm/plat-s3c24xx/s3c2443.h b/include/asm-arm/plat-s3c24xx/s3c2443.h new file mode 100644 index 000000000000..11d83b5c84e6 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/s3c2443.h @@ -0,0 +1,32 @@ +/* linux/include/asm-arm/plat-s3c24xx/s3c2443.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2443 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifdef CONFIG_CPU_S3C2443 + +struct s3c2410_uartcfg; + +extern int s3c2443_init(void); + +extern void s3c2443_map_io(struct map_desc *mach_desc, int size); + +extern void s3c2443_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c2443_init_clocks(int xtal); + +extern int s3c2443_baseclk_add(void); + +#else +#define s3c2443_init_clocks NULL +#define s3c2443_init_uarts NULL +#define s3c2443_map_io NULL +#define s3c2443_init NULL +#endif -- cgit v1.2.3 From 285f4930f239d95cb8d4fdf45a52870d744bed8f Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 15 Feb 2007 16:48:58 +0100 Subject: [ARM] 4199/1: S3C2443: SMDK2443 machine addition Add support for SMDK2443 to arch/arm/mach-s3c2443 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2443/Kconfig | 8 +- arch/arm/mach-s3c2443/Makefile | 2 + arch/arm/mach-s3c2443/mach-smdk2443.c | 138 ++++++++++++++++++++++++++++++++++ 3 files changed, 147 insertions(+), 1 deletion(-) create mode 100644 arch/arm/mach-s3c2443/mach-smdk2443.c (limited to 'arch') diff --git a/arch/arm/mach-s3c2443/Kconfig b/arch/arm/mach-s3c2443/Kconfig index 0d8d7bf9a96b..722bdea3c193 100644 --- a/arch/arm/mach-s3c2443/Kconfig +++ b/arch/arm/mach-s3c2443/Kconfig @@ -14,5 +14,11 @@ config CPU_S3C2443 menu "S3C2443 Machines" -endmenu +config MACH_SMDK2443 + bool "SMDK2443" + select CPU_S3C2443 + select MACH_SMDK + help + Say Y here if you are using an SMDK2443 +endmenu diff --git a/arch/arm/mach-s3c2443/Makefile b/arch/arm/mach-s3c2443/Makefile index 397475affbe1..a878076beecd 100644 --- a/arch/arm/mach-s3c2443/Makefile +++ b/arch/arm/mach-s3c2443/Makefile @@ -14,3 +14,5 @@ obj-$(CONFIG_CPU_S3C2443) += irq.o obj-$(CONFIG_CPU_S3C2443) += clock.o # Machine support + +obj-$(CONFIG_MACH_SMDK2443) += mach-smdk2443.o diff --git a/arch/arm/mach-s3c2443/mach-smdk2443.c b/arch/arm/mach-s3c2443/mach-smdk2443.c new file mode 100644 index 000000000000..1ac45b8b5cfb --- /dev/null +++ b/arch/arm/mach-s3c2443/mach-smdk2443.c @@ -0,0 +1,138 @@ +/* linux/arch/arm/mach-s3c2443/mach-smdk2443.c + * + * Copyright (c) 2007 Simtec Electronics + * Ben Dooks + * + * http://www.fluff.org/ben/smdk2443/ + * + * Thanks to Samsung for the loan of an SMDK2443 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include +#include +#include +#include +#include + +#include + +static struct map_desc smdk2443_iodesc[] __initdata = { + /* ISA IO Space map (memory space selected by A24) */ + + { + .virtual = (u32)S3C24XX_VA_ISA_WORD, + .pfn = __phys_to_pfn(S3C2410_CS2), + .length = 0x10000, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_WORD + 0x10000, + .pfn = __phys_to_pfn(S3C2410_CS2 + (1<<24)), + .length = SZ_4M, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_BYTE, + .pfn = __phys_to_pfn(S3C2410_CS2), + .length = 0x10000, + .type = MT_DEVICE, + }, { + .virtual = (u32)S3C24XX_VA_ISA_BYTE + 0x10000, + .pfn = __phys_to_pfn(S3C2410_CS2 + (1<<24)), + .length = SZ_4M, + .type = MT_DEVICE, + } +}; + +#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg smdk2443_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x03, + .ufcon = 0x51, + }, + /* IR port */ + [2] = { + .hwport = 2, + .flags = 0, + .ucon = 0x3c5, + .ulcon = 0x43, + .ufcon = 0x51, + } +}; + +static struct platform_device *smdk2443_devices[] __initdata = { + &s3c_device_wdt, + &s3c_device_i2c, +}; + +static struct s3c24xx_board smdk2443_board __initdata = { + .devices = smdk2443_devices, + .devices_count = ARRAY_SIZE(smdk2443_devices) +}; + +static void __init smdk2443_map_io(void) +{ + s3c24xx_init_io(smdk2443_iodesc, ARRAY_SIZE(smdk2443_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(smdk2443_uartcfgs, ARRAY_SIZE(smdk2443_uartcfgs)); + s3c24xx_set_board(&smdk2443_board); +} + +static void __init smdk2443_machine_init(void) +{ + smdk_machine_init(); +} + +MACHINE_START(SMDK2443, "SMDK2443") + /* Maintainer: Ben Dooks */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + + .init_irq = s3c24xx_init_irq, + .map_io = smdk2443_map_io, + .init_machine = smdk2443_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END -- cgit v1.2.3 From 5ea22225e222b1a46d095ec3d754de052f6b284a Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 15 Feb 2007 17:32:20 +0100 Subject: [ARM] 4200/1: S3C2443: Update s3c2410_defconfig to add SMDK2443 Add SMDK2443 to s3c2410_defconfig Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/configs/s3c2410_defconfig | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index 7c8025bc278a..df19e3632038 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit # Linux kernel version: 2.6.20 -# Tue Feb 13 16:43:14 2007 +# Thu Feb 15 11:26:24 2007 # CONFIG_ARM=y # CONFIG_GENERIC_TIME is not set @@ -189,6 +189,12 @@ CONFIG_CPU_S3C2442=y # S3C2442 Machines # CONFIG_SMDK2440_CPU2442=y +CONFIG_CPU_S3C2443=y + +# +# S3C2443 Machines +# +CONFIG_MACH_SMDK2443=y # # Processor Type -- cgit v1.2.3 From d9c0ebbda522b64607cd2b0064b9bb040c53bcaf Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 15 Feb 2007 22:29:36 +0100 Subject: [ARM] 4203/1: S3C2443: use S3C2412 nand driver Use the S3C2412 nand driver for the S3C2443 as it is register compatible. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2443/s3c2443.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2443/s3c2443.c b/arch/arm/mach-s3c2443/s3c2443.c index bc14f772ff24..9b91235c15d2 100644 --- a/arch/arm/mach-s3c2443/s3c2443.c +++ b/arch/arm/mach-s3c2443/s3c2443.c @@ -53,6 +53,8 @@ int __init s3c2443_init(void) { printk("S3C2443: Initialising architecture\n"); + s3c_device_nand.name = "s3c2412-nand"; + return sysdev_register(&s3c2443_sysdev); } -- cgit v1.2.3 From b4f14eb86cda9324a2ffbdf534385d012967acd8 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 15 Feb 2007 22:53:52 +0100 Subject: [ARM] 4205/1: S3C2443: Add cpu specific reset hook Hook in a cpu specific reset function for the S3C2443 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2443/s3c2443.c | 10 +++++++++- include/asm-arm/arch-s3c2410/regs-s3c2443-clock.h | 2 ++ 2 files changed, 11 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2443/s3c2443.c b/arch/arm/mach-s3c2443/s3c2443.c index 9b91235c15d2..11b1d0b310c3 100644 --- a/arch/arm/mach-s3c2443/s3c2443.c +++ b/arch/arm/mach-s3c2443/s3c2443.c @@ -29,7 +29,8 @@ #include #include -#include +#include +#include #include #include @@ -49,10 +50,17 @@ static struct sys_device s3c2443_sysdev = { .cls = &s3c2443_sysclass, }; +static void s3c2443_hard_reset(void) +{ + __raw_writel(S3C2443_SWRST_RESET, S3C2443_SWRST); +} + int __init s3c2443_init(void) { printk("S3C2443: Initialising architecture\n"); + s3c24xx_reset_hook = s3c2443_hard_reset; + s3c_device_nand.name = "s3c2412-nand"; return sysdev_register(&s3c2443_sysdev); diff --git a/include/asm-arm/arch-s3c2410/regs-s3c2443-clock.h b/include/asm-arm/arch-s3c2410/regs-s3c2443-clock.h index e696554f9c21..ff0536d2de42 100644 --- a/include/asm-arm/arch-s3c2410/regs-s3c2443-clock.h +++ b/include/asm-arm/arch-s3c2410/regs-s3c2443-clock.h @@ -38,6 +38,8 @@ #define S3C2443_PWRCFG S3C2443_CLKREG(0x60) #define S3C2443_RSTCON S3C2443_CLKREG(0x64) +#define S3C2443_SWRST_RESET (0x533c2443) + #define S3C2443_PLLCON_OFF (1<<24) #define S3C2443_CLKSRC_I2S_EXT (1<<14) -- cgit v1.2.3 From a930609496b39284a93182ec3beb9dc9bf3651ec Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 16 Feb 2007 00:17:07 +0100 Subject: [ARM] 4206/1: SMDK2440: Fix lcd type in platform data Set the LCD display type field in the platform data so that the LCD driver initialise the display as an TFT display Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2440/mach-smdk2440.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2440/mach-smdk2440.c b/arch/arm/mach-s3c2440/mach-smdk2440.c index 270e42b9b5c1..7e7d4408af36 100644 --- a/arch/arm/mach-s3c2440/mach-smdk2440.c +++ b/arch/arm/mach-s3c2440/mach-smdk2440.c @@ -144,6 +144,7 @@ static struct s3c2410fb_mach_info smdk2440_lcd_cfg __initdata = { #endif .lpcsel = ((0xCE6) & ~7) | 1<<4, + .type = S3C2410_LCDCON1_TFT16BPP, .width = 240, .height = 320, -- cgit v1.2.3 From 90bc8566fb40b12167b49d972c85d2e509eea55f Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 16 Feb 2007 12:54:15 +0100 Subject: [ARM] 4209/1: S3C24XX: remove unnecessary includes of iomd.h Machines in the S3C24XX architectures should not be including as this is not needed. Also remove commented out includes Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/mach-h1940.c | 2 -- arch/arm/mach-s3c2410/mach-n30.c | 1 - arch/arm/mach-s3c2412/mach-vstms.c | 1 - arch/arm/mach-s3c2440/mach-rx3715.c | 1 - arch/arm/mach-s3c2440/mach-smdk2440.c | 2 -- arch/arm/mach-s3c2443/mach-smdk2443.c | 1 - 6 files changed, 8 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 2b495b7b427b..01c60d0923cd 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -25,12 +25,10 @@ #include #include -#include #include #include #include - #include #include #include diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c index dbac7311f98f..261aa4cc0770 100644 --- a/arch/arm/mach-s3c2410/mach-n30.c +++ b/arch/arm/mach-s3c2410/mach-n30.c @@ -29,7 +29,6 @@ #include #include -#include #include #include #include diff --git a/arch/arm/mach-s3c2412/mach-vstms.c b/arch/arm/mach-s3c2412/mach-vstms.c index f1afb707ff16..4231b549d797 100644 --- a/arch/arm/mach-s3c2412/mach-vstms.c +++ b/arch/arm/mach-s3c2412/mach-vstms.c @@ -28,7 +28,6 @@ #include #include -#include #include #include #include diff --git a/arch/arm/mach-s3c2440/mach-rx3715.c b/arch/arm/mach-s3c2440/mach-rx3715.c index 1d4e19bd9206..480ccde63fb4 100644 --- a/arch/arm/mach-s3c2440/mach-rx3715.c +++ b/arch/arm/mach-s3c2440/mach-rx3715.c @@ -33,7 +33,6 @@ #include #include -#include #include #include #include diff --git a/arch/arm/mach-s3c2440/mach-smdk2440.c b/arch/arm/mach-s3c2440/mach-smdk2440.c index 7e7d4408af36..c17eb5b1f6b4 100644 --- a/arch/arm/mach-s3c2440/mach-smdk2440.c +++ b/arch/arm/mach-s3c2440/mach-smdk2440.c @@ -27,12 +27,10 @@ #include #include -#include #include #include #include -//#include #include #include #include diff --git a/arch/arm/mach-s3c2443/mach-smdk2443.c b/arch/arm/mach-s3c2443/mach-smdk2443.c index 1ac45b8b5cfb..e82aaff7dee4 100644 --- a/arch/arm/mach-s3c2443/mach-smdk2443.c +++ b/arch/arm/mach-s3c2443/mach-smdk2443.c @@ -27,7 +27,6 @@ #include #include -#include #include #include #include -- cgit v1.2.3 From 72262e8b19034d2605d452d91717d56738598707 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 16 Feb 2007 13:02:42 +0100 Subject: [ARM] 4202/2: S3C2443: IRQ sub source handlers Add IRQ handlers for the IRQs which originate from the sub-interrupt register on the S3C2443 Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2443/irq.c | 238 ++++++++++++++++++++++++++++++++++++-------- 1 file changed, 199 insertions(+), 39 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2443/irq.c b/arch/arm/mach-s3c2443/irq.c index f7058823a0e1..7a45b6dcb73e 100644 --- a/arch/arm/mach-s3c2443/irq.c +++ b/arch/arm/mach-s3c2443/irq.c @@ -39,12 +39,12 @@ #include #include -/* WDT/AC97 */ +#define INTMSK(start, end) ((1 << ((end) + 1 - (start))) - 1) -static void s3c_irq_demux_wdtac97(unsigned int irq, - struct irq_desc *desc) +static inline void s3c2443_irq_demux(unsigned int irq, unsigned int len) { unsigned int subsrc, submsk; + unsigned int end; struct irq_desc *mydesc; /* read the current pending interrupts, and the mask @@ -53,63 +53,199 @@ static void s3c_irq_demux_wdtac97(unsigned int irq, subsrc = __raw_readl(S3C2410_SUBSRCPND); submsk = __raw_readl(S3C2410_INTSUBMSK); - subsrc &= ~submsk; - subsrc >>= 27; - subsrc &= 3; - - if (subsrc != 0) { - if (subsrc & 1) { - mydesc = irq_desc + IRQ_S3C2443_WDT; - desc_handle_irq(IRQ_S3C2443_WDT, mydesc); - } - if (subsrc & 2) { - mydesc = irq_desc + IRQ_S3C2443_AC97; - desc_handle_irq(IRQ_S3C2443_AC97, mydesc); - } + subsrc &= ~submsk; + subsrc >>= (irq - S3C2410_IRQSUB(0)); + subsrc &= (1 << len)-1; + + end = len + irq; + mydesc = irq_desc + irq; + + for (; irq < end && subsrc; irq++) { + if (subsrc & 1) + desc_handle_irq(irq, mydesc); + + mydesc++; + subsrc >>= 1; } } +/* WDT/AC97 sub interrupts */ + +static void s3c2443_irq_demux_wdtac97(unsigned int irq, struct irq_desc *desc) +{ + s3c2443_irq_demux(IRQ_S3C2443_WDT, 4); +} -#define INTMSK_WDT (1UL << (IRQ_WDT - IRQ_EINT0)) +#define INTMSK_WDTAC97 (1UL << (IRQ_WDT - IRQ_EINT0)) +#define SUBMSK_WDTAC97 INTMSK(IRQ_S3C2443_WDT, IRQ_S3C2443_AC97) -static void -s3c_irq_wdtac97_mask(unsigned int irqno) +static void s3c2443_irq_wdtac97_mask(unsigned int irqno) { - s3c_irqsub_mask(irqno, INTMSK_WDT, 3<<27); + s3c_irqsub_mask(irqno, INTMSK_WDTAC97, SUBMSK_WDTAC97); } -static void -s3c_irq_wdtac97_unmask(unsigned int irqno) +static void s3c2443_irq_wdtac97_unmask(unsigned int irqno) { - s3c_irqsub_unmask(irqno, INTMSK_WDT); + s3c_irqsub_unmask(irqno, INTMSK_WDTAC97); } -static void -s3c_irq_wdtac97_ack(unsigned int irqno) +static void s3c2443_irq_wdtac97_ack(unsigned int irqno) { - s3c_irqsub_maskack(irqno, INTMSK_WDT, 3<<27); + s3c_irqsub_maskack(irqno, INTMSK_WDTAC97, SUBMSK_WDTAC97); } -static struct irq_chip s3c_irq_wdtac97 = { - .mask = s3c_irq_wdtac97_mask, - .unmask = s3c_irq_wdtac97_unmask, - .ack = s3c_irq_wdtac97_ack, +static struct irq_chip s3c2443_irq_wdtac97 = { + .mask = s3c2443_irq_wdtac97_mask, + .unmask = s3c2443_irq_wdtac97_unmask, + .ack = s3c2443_irq_wdtac97_ack, }; -static int s3c2443_irq_add(struct sys_device *sysdev) + +/* LCD sub interrupts */ + +static void s3c2443_irq_demux_lcd(unsigned int irq, struct irq_desc *desc) { - unsigned int irqno; + s3c2443_irq_demux(IRQ_S3C2443_LCD1, 4); +} - printk("S3C2443: IRQ Support\n"); +#define INTMSK_LCD (1UL << (IRQ_LCD - IRQ_EINT0)) +#define SUBMSK_LCD INTMSK(IRQ_S3C2443_LCD1, IRQ_S3C2443_LCD4) + +static void s3c2443_irq_lcd_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_LCD, SUBMSK_LCD); +} + +static void s3c2443_irq_lcd_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_LCD); +} + +static void s3c2443_irq_lcd_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_LCD, SUBMSK_LCD); +} + +static struct irq_chip s3c2443_irq_lcd = { + .mask = s3c2443_irq_lcd_mask, + .unmask = s3c2443_irq_lcd_unmask, + .ack = s3c2443_irq_lcd_ack, +}; + + +/* DMA sub interrupts */ + +static void s3c2443_irq_demux_dma(unsigned int irq, struct irq_desc *desc) +{ + s3c2443_irq_demux(IRQ_S3C2443_DMA1, 6); +} + +#define INTMSK_DMA (1UL << (IRQ_S3C2443_DMA - IRQ_EINT0)) +#define SUBMSK_DMA INTMSK(IRQ_S3C2443_DMA0, IRQ_S3C2443_DMA5) + + +static void s3c2443_irq_dma_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_DMA, SUBMSK_DMA); +} + +static void s3c2443_irq_dma_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_DMA); +} + +static void s3c2443_irq_dma_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_DMA, SUBMSK_DMA); +} + +static struct irq_chip s3c2443_irq_dma = { + .mask = s3c2443_irq_dma_mask, + .unmask = s3c2443_irq_dma_unmask, + .ack = s3c2443_irq_dma_ack, +}; + + +/* UART3 sub interrupts */ + +static void s3c2443_irq_demux_uart3(unsigned int irq, struct irq_desc *desc) +{ + s3c2443_irq_demux(IRQ_S3C2443_UART3, 3); +} - /* add new chained handler for wdt, ac7 */ +#define INTMSK_UART3 (1UL << (IRQ_S3C2443_UART3 - IRQ_EINT0)) +#define SUBMSK_UART3 (0xf << (IRQ_S3C2443_RX3 - S3C2410_IRQSUB(0))) - set_irq_chip(IRQ_WDT, &s3c_irq_level_chip); - set_irq_handler(IRQ_WDT, handle_level_irq); - set_irq_chained_handler(IRQ_WDT, s3c_irq_demux_wdtac97); - for (irqno = IRQ_S3C2443_WDT; irqno <= IRQ_S3C2443_AC97; irqno++) { - set_irq_chip(irqno, &s3c_irq_wdtac97); +static void s3c2443_irq_uart3_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_UART3, SUBMSK_UART3); +} + +static void s3c2443_irq_uart3_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_UART3); +} + +static void s3c2443_irq_uart3_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_UART3, SUBMSK_UART3); +} + +static struct irq_chip s3c2443_irq_uart3 = { + .mask = s3c2443_irq_uart3_mask, + .unmask = s3c2443_irq_uart3_unmask, + .ack = s3c2443_irq_uart3_ack, +}; + + +/* CAM sub interrupts */ + +static void s3c2443_irq_demux_cam(unsigned int irq, struct irq_desc *desc) +{ + s3c2443_irq_demux(IRQ_S3C2440_CAM_C, 4); +} + +#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0)) +#define SUBMSK_CAM INTMSK(IRQ_S3C2440_CAM_C, IRQ_S3C2440_CAM_P) + +static void s3c2443_irq_cam_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_CAM, SUBMSK_CAM); +} + +static void s3c2443_irq_cam_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_CAM); +} + +static void s3c2443_irq_cam_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_CAM, SUBMSK_CAM); +} + +static struct irq_chip s3c2443_irq_cam = { + .mask = s3c2443_irq_cam_mask, + .unmask = s3c2443_irq_cam_unmask, + .ack = s3c2443_irq_cam_ack, +}; + +/* IRQ initialisation code */ + +static int __init s3c2443_add_sub(unsigned int base, + void (*demux)(unsigned int, + struct irq_desc *), + struct irq_chip *chip, + unsigned int start, unsigned int end) +{ + unsigned int irqno; + + set_irq_chip(base, &s3c_irq_level_chip); + set_irq_handler(base, handle_level_irq); + set_irq_chained_handler(base, demux); + + for (irqno = start; irqno <= end; irqno++) { + set_irq_chip(irqno, chip); set_irq_handler(irqno, handle_level_irq); set_irq_flags(irqno, IRQF_VALID); } @@ -117,6 +253,30 @@ static int s3c2443_irq_add(struct sys_device *sysdev) return 0; } +static int s3c2443_irq_add(struct sys_device *sysdev) +{ + printk("S3C2443: IRQ Support\n"); + + s3c2443_add_sub(IRQ_CAM, s3c2443_irq_demux_cam, &s3c2443_irq_cam, + IRQ_S3C2440_CAM_C, IRQ_S3C2440_CAM_P); + + s3c2443_add_sub(IRQ_LCD, s3c2443_irq_demux_lcd, &s3c2443_irq_lcd, + IRQ_S3C2443_LCD1, IRQ_S3C2443_LCD4); + + s3c2443_add_sub(IRQ_S3C2443_DMA, s3c2443_irq_demux_dma, + &s3c2443_irq_dma, IRQ_S3C2443_DMA0, IRQ_S3C2443_DMA5); + + s3c2443_add_sub(IRQ_S3C2443_UART3, s3c2443_irq_demux_uart3, + &s3c2443_irq_uart3, + IRQ_S3C2443_RX3, IRQ_S3C2443_ERR3); + + s3c2443_add_sub(IRQ_WDT, s3c2443_irq_demux_wdtac97, + &s3c2443_irq_wdtac97, + IRQ_S3C2443_WDT, IRQ_S3C2443_AC97); + + return 0; +} + static struct sysdev_driver s3c2443_irq_driver = { .add = s3c2443_irq_add, }; -- cgit v1.2.3 From cb36bb7516fdd1a2a7e9155413b83d4330e4c4a7 Mon Sep 17 00:00:00 2001 From: George G. Davis Date: Wed, 14 Feb 2007 17:44:28 +0100 Subject: [ARM] 4191/1: Remove redundant __flush_dcache_page() function prototype Commit 1c9d3df5e88ad7db23f5b22f4341c39722a904a4 added function prototype __flush_dcache_page() in include/asm-arm/cacheflush.h. So we can remove the prototype for same in arch/arm/mm/fault-armv.c since it is now redundant to have it there. Signed-off-by: George G. Davis Signed-off-by: Russell King --- arch/arm/mm/fault-armv.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/fault-armv.c b/arch/arm/mm/fault-armv.c index cf95c5d0ce4c..44558d5f9313 100644 --- a/arch/arm/mm/fault-armv.c +++ b/arch/arm/mm/fault-armv.c @@ -119,8 +119,6 @@ make_coherent(struct address_space *mapping, struct vm_area_struct *vma, unsigne flush_cache_page(vma, addr, pfn); } -void __flush_dcache_page(struct address_space *mapping, struct page *page); - /* * Take care of architecture specific things when placing a new PTE into * a page table, or changing an existing PTE. Basically, there are two -- cgit v1.2.3 From f1e1398654eb97269590a5a76f0aedb607fe5d0f Mon Sep 17 00:00:00 2001 From: David Brownell Date: Fri, 16 Feb 2007 06:36:50 +0100 Subject: [ARM] 4207/1: defconfig fixes, use RTC_DRV_AT91RM9200 When "rtc-at91" was renamed to "rtc-at91rm9200" not all the relevant defconfig entries were updated. Signed-off-by: David Brownell Signed-off-by: Russell King --- arch/arm/configs/ateb9200_defconfig | 2 +- arch/arm/configs/csb337_defconfig | 2 +- arch/arm/configs/kafa_defconfig | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/configs/ateb9200_defconfig b/arch/arm/configs/ateb9200_defconfig index 3de5c643848c..baa97698c744 100644 --- a/arch/arm/configs/ateb9200_defconfig +++ b/arch/arm/configs/ateb9200_defconfig @@ -1066,7 +1066,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8563 is not set # CONFIG_RTC_DRV_RS5C372 is not set # CONFIG_RTC_DRV_M48T86 is not set -CONFIG_RTC_DRV_AT91=y +CONFIG_RTC_DRV_AT91RM9200=y # CONFIG_RTC_DRV_TEST is not set # diff --git a/arch/arm/configs/csb337_defconfig b/arch/arm/configs/csb337_defconfig index 8e55f55333be..88e5d28aeec7 100644 --- a/arch/arm/configs/csb337_defconfig +++ b/arch/arm/configs/csb337_defconfig @@ -988,7 +988,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_RS5C372 is not set # CONFIG_RTC_DRV_M48T86 is not set -CONFIG_RTC_DRV_AT91=y +CONFIG_RTC_DRV_AT91RM9200=y # CONFIG_RTC_DRV_TEST is not set # CONFIG_RTC_DRV_V3020 is not set diff --git a/arch/arm/configs/kafa_defconfig b/arch/arm/configs/kafa_defconfig index a4cdafc1548a..a0f48d54fbcc 100644 --- a/arch/arm/configs/kafa_defconfig +++ b/arch/arm/configs/kafa_defconfig @@ -718,7 +718,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8563 is not set # CONFIG_RTC_DRV_RS5C372 is not set # CONFIG_RTC_DRV_M48T86 is not set -CONFIG_RTC_DRV_AT91=y +CONFIG_RTC_DRV_AT91RM9200=y # CONFIG_RTC_DRV_TEST is not set # -- cgit v1.2.3 From dd1d2f4439af3bc80c047a13a8a2be60df1953cd Mon Sep 17 00:00:00 2001 From: Jan Altenberg Date: Fri, 16 Feb 2007 01:37:10 -0800 Subject: [ARM] at91: correct value for AT91_RSTC_KEY - Remove a duplicated define for AT91_RSTC_KEY - Set AT91_RSTC_KEY to the correct value - Replace the hardcoded keys in at91sam9620.c and at91sam9261.c by AT91_RSTC_KEY Signed-off-by: Jan Altenberg Acked-by: Andrew Victor Signed-off-by: Andrew Morton Signed-off-by: Russell King --- arch/arm/mach-at91/at91sam9260.c | 2 +- arch/arm/mach-at91/at91sam9261.c | 2 +- include/asm-arm/arch-at91/at91_rstc.h | 3 +-- 3 files changed, 3 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index 003c27c2ef65..6ea41d8266cb 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -259,7 +259,7 @@ static struct at91_gpio_bank at91sam9260_gpio[] = { static void at91sam9260_reset(void) { - at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); + at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); } diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 1a9102368f11..784d1e682d6d 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -225,7 +225,7 @@ static struct at91_gpio_bank at91sam9261_gpio[] = { static void at91sam9261_reset(void) { - at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); + at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); } diff --git a/include/asm-arm/arch-at91/at91_rstc.h b/include/asm-arm/arch-at91/at91_rstc.h index 0b7afbc015a2..fb8d1618a231 100644 --- a/include/asm-arm/arch-at91/at91_rstc.h +++ b/include/asm-arm/arch-at91/at91_rstc.h @@ -17,7 +17,7 @@ #define AT91_RSTC_PROCRST (1 << 0) /* Processor Reset */ #define AT91_RSTC_PERRST (1 << 2) /* Peripheral Reset */ #define AT91_RSTC_EXTRST (1 << 3) /* External Reset */ -#define AT91_RSTC_KEY (0xff << 24) /* KEY Password */ +#define AT91_RSTC_KEY (0xa5 << 24) /* KEY Password */ #define AT91_RSTC_SR (AT91_RSTC + 0x04) /* Reset Controller Status Register */ #define AT91_RSTC_URSTS (1 << 0) /* User Reset Status */ @@ -34,6 +34,5 @@ #define AT91_RSTC_URSTEN (1 << 0) /* User Reset Enable */ #define AT91_RSTC_URSTIEN (1 << 4) /* User Reset Interrupt Enable */ #define AT91_RSTC_ERSTL (0xf << 8) /* External Reset Length */ -#define AT91_RSTC_KEY (0xff << 24) /* KEY Password */ #endif -- cgit v1.2.3 From 0e0ba76926c37f11f38670db0cb33728f502551e Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Thu, 15 Feb 2007 19:05:29 +0100 Subject: [ARM] 4201/1: SMP barriers pair needed for the secondary boot process In some situations, the pen_release store in platform_secondary_init() may stay forever in the write buffer while the CPU is waiting on the boot_lock to be released in boot_secondary(). The primary CPU could never see the pen_release update without the barriers. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- arch/arm/mach-realview/platsmp.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c index 709a9b1ac634..fce3596f9950 100644 --- a/arch/arm/mach-realview/platsmp.c +++ b/arch/arm/mach-realview/platsmp.c @@ -59,6 +59,7 @@ void __cpuinit platform_secondary_init(unsigned int cpu) * pen, then head off into the C entry point */ pen_release = -1; + smp_wmb(); /* * Synchronise with the boot thread. @@ -102,6 +103,7 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle) timeout = jiffies + (1 * HZ); while (time_before(jiffies, timeout)) { + smp_rmb(); if (pen_release == -1) break; -- cgit v1.2.3 From c587e4a6a4d808fd2a1c4e7fb2d5a3a31e300d23 Mon Sep 17 00:00:00 2001 From: Richard Purdie Date: Tue, 6 Feb 2007 21:29:00 +0100 Subject: [ARM] 4137/1: Add kexec support Add kexec support to ARM. Improvements like commandline handling could be made but this patch gives basic functional support. It uses the next available syscall number, 347. Once the syscall number is known, userspace support will be finalised/submitted to kexec-tools, various patches already exist. Originally based on a patch by Maxim Syrchin but updated and forward ported by various people. Signed-off-by: Richard Purdie Signed-off-by: Russell King --- arch/arm/Kconfig | 14 +++++++ arch/arm/kernel/Makefile | 1 + arch/arm/kernel/calls.S | 1 + arch/arm/kernel/machine_kexec.c | 78 +++++++++++++++++++++++++++++++++++++++ arch/arm/kernel/relocate_kernel.S | 74 +++++++++++++++++++++++++++++++++++++ include/asm-arm/kexec.h | 30 +++++++++++++++ include/asm-arm/unistd.h | 1 + include/linux/kexec.h | 1 + 8 files changed, 200 insertions(+) create mode 100644 arch/arm/kernel/machine_kexec.c create mode 100644 arch/arm/kernel/relocate_kernel.S create mode 100644 include/asm-arm/kexec.h (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6783c2e5512d..a8298949d166 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -738,6 +738,20 @@ config XIP_PHYS_ADDR be linked for and stored to. This address is dependent on your own flash usage. +config KEXEC + bool "Kexec system call (EXPERIMENTAL)" + depends on EXPERIMENTAL + help + kexec is a system call that implements the ability to shutdown your + current kernel, and to start another kernel. It is like a reboot + but it is indepedent of the system firmware. And like a reboot + you can start any kernel with it, not just Linux. + + It is an ongoing process to be certain the hardware in a machine + is properly shutdown, so do not be surprised if this code does not + initially work for you. It may help to enable device hotplugging + support. + endmenu if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_IMX ) diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile index ab06a86e85d5..d5002889773e 100644 --- a/arch/arm/kernel/Makefile +++ b/arch/arm/kernel/Makefile @@ -19,6 +19,7 @@ obj-$(CONFIG_ARTHUR) += arthur.o obj-$(CONFIG_ISA_DMA) += dma-isa.o obj-$(CONFIG_PCI) += bios32.o isa.o obj-$(CONFIG_SMP) += smp.o +obj-$(CONFIG_KEXEC) += machine_kexec.o relocate_kernel.o obj-$(CONFIG_OABI_COMPAT) += sys_oabi-compat.o obj-$(CONFIG_CRUNCH) += crunch.o crunch-bits.o diff --git a/arch/arm/kernel/calls.S b/arch/arm/kernel/calls.S index f7598cbc7ec5..ae89cdd82b16 100644 --- a/arch/arm/kernel/calls.S +++ b/arch/arm/kernel/calls.S @@ -356,6 +356,7 @@ CALL(sys_move_pages) /* 345 */ CALL(sys_getcpu) CALL(sys_ni_syscall) /* eventually epoll_pwait */ + CALL(sys_kexec_load) #ifndef syscalls_counted .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls #define syscalls_counted diff --git a/arch/arm/kernel/machine_kexec.c b/arch/arm/kernel/machine_kexec.c new file mode 100644 index 000000000000..863c66454f2b --- /dev/null +++ b/arch/arm/kernel/machine_kexec.c @@ -0,0 +1,78 @@ +/* + * machine_kexec.c - handle transition of Linux booting another kernel + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +const extern unsigned char relocate_new_kernel[]; +const extern unsigned int relocate_new_kernel_size; + +extern void setup_mm_for_reboot(char mode); + +extern unsigned long kexec_start_address; +extern unsigned long kexec_indirection_page; +extern unsigned long kexec_mach_type; + +/* + * Provide a dummy crash_notes definition while crash dump arrives to arm. + * This prevents breakage of crash_notes attribute in kernel/ksysfs.c. + */ + +int machine_kexec_prepare(struct kimage *image) +{ + return 0; +} + +void machine_kexec_cleanup(struct kimage *image) +{ +} + +void machine_shutdown(void) +{ +} + +void machine_crash_shutdown(struct pt_regs *regs) +{ +} + +void machine_kexec(struct kimage *image) +{ + unsigned long page_list; + unsigned long reboot_code_buffer_phys; + void *reboot_code_buffer; + + + page_list = image->head & PAGE_MASK; + + /* we need both effective and real address here */ + reboot_code_buffer_phys = + page_to_pfn(image->control_code_page) << PAGE_SHIFT; + reboot_code_buffer = page_address(image->control_code_page); + + /* Prepare parameters for reboot_code_buffer*/ + kexec_start_address = image->start; + kexec_indirection_page = page_list; + kexec_mach_type = machine_arch_type; + + /* copy our kernel relocation code to the control code page */ + memcpy(reboot_code_buffer, + relocate_new_kernel, relocate_new_kernel_size); + + + flush_icache_range((unsigned long) reboot_code_buffer, + (unsigned long) reboot_code_buffer + KEXEC_CONTROL_CODE_SIZE); + printk(KERN_INFO "Bye!\n"); + + cpu_proc_fin(); + setup_mm_for_reboot(0); /* mode is not used, so just pass 0*/ + cpu_reset(reboot_code_buffer_phys); +} diff --git a/arch/arm/kernel/relocate_kernel.S b/arch/arm/kernel/relocate_kernel.S new file mode 100644 index 000000000000..7baadae7cb27 --- /dev/null +++ b/arch/arm/kernel/relocate_kernel.S @@ -0,0 +1,74 @@ +/* + * relocate_kernel.S - put the kernel image in place to boot + */ + +#include + + .globl relocate_new_kernel +relocate_new_kernel: + + ldr r0,kexec_indirection_page + ldr r1,kexec_start_address + + +0: /* top, read another word for the indirection page */ + ldr r3, [r0],#4 + + /* Is it a destination page. Put destination address to r4 */ + tst r3,#1,0 + beq 1f + bic r4,r3,#1 + b 0b +1: + /* Is it an indirection page */ + tst r3,#2,0 + beq 1f + bic r0,r3,#2 + b 0b +1: + + /* are we done ? */ + tst r3,#4,0 + beq 1f + b 2f + +1: + /* is it source ? */ + tst r3,#8,0 + beq 0b + bic r3,r3,#8 + mov r6,#1024 +9: + ldr r5,[r3],#4 + str r5,[r4],#4 + subs r6,r6,#1 + bne 9b + b 0b + +2: + /* Jump to relocated kernel */ + mov lr,r1 + mov r0,#0 + ldr r1,kexec_mach_type + mov r2,#0 + mov pc,lr + + .globl kexec_start_address +kexec_start_address: + .long 0x0 + + .globl kexec_indirection_page +kexec_indirection_page: + .long 0x0 + + .globl kexec_mach_type +kexec_mach_type: + .long 0x0 + +relocate_new_kernel_end: + + .globl relocate_new_kernel_size +relocate_new_kernel_size: + .long relocate_new_kernel_end - relocate_new_kernel + + diff --git a/include/asm-arm/kexec.h b/include/asm-arm/kexec.h new file mode 100644 index 000000000000..8c1c6162a80c --- /dev/null +++ b/include/asm-arm/kexec.h @@ -0,0 +1,30 @@ +#ifndef _ARM_KEXEC_H +#define _ARM_KEXEC_H + +#ifdef CONFIG_KEXEC + +/* Maximum physical address we can use pages from */ +#define KEXEC_SOURCE_MEMORY_LIMIT (-1UL) +/* Maximum address we can reach in physical address mode */ +#define KEXEC_DESTINATION_MEMORY_LIMIT (-1UL) +/* Maximum address we can use for the control code buffer */ +#define KEXEC_CONTROL_MEMORY_LIMIT TASK_SIZE + +#define KEXEC_CONTROL_CODE_SIZE 4096 + +#define KEXEC_ARCH KEXEC_ARCH_ARM + +#ifndef __ASSEMBLY__ + +#define MAX_NOTE_BYTES 1024 + +struct kimage; +/* Provide a dummy definition to avoid build failures. */ +static inline void crash_setup_regs(struct pt_regs *newregs, + struct pt_regs *oldregs) { } + +#endif /* __ASSEMBLY__ */ + +#endif /* CONFIG_KEXEC */ + +#endif /* _ARM_KEXEC_H */ diff --git a/include/asm-arm/unistd.h b/include/asm-arm/unistd.h index 97e7060000cf..0991b7bc3f78 100644 --- a/include/asm-arm/unistd.h +++ b/include/asm-arm/unistd.h @@ -372,6 +372,7 @@ #define __NR_move_pages (__NR_SYSCALL_BASE+344) #define __NR_getcpu (__NR_SYSCALL_BASE+345) /* 346 for epoll_pwait */ +#define __NR_sys_kexec_load (__NR_SYSCALL_BASE+347) /* * The following SWIs are ARM private. diff --git a/include/linux/kexec.h b/include/linux/kexec.h index d02425cdd801..696e5ec63f77 100644 --- a/include/linux/kexec.h +++ b/include/linux/kexec.h @@ -125,6 +125,7 @@ extern struct kimage *kexec_crash_image; #define KEXEC_ARCH_PPC (20 << 16) #define KEXEC_ARCH_PPC64 (21 << 16) #define KEXEC_ARCH_IA_64 (50 << 16) +#define KEXEC_ARCH_ARM (40 << 16) #define KEXEC_ARCH_S390 (22 << 16) #define KEXEC_ARCH_SH (42 << 16) #define KEXEC_ARCH_MIPS_LE (10 << 16) -- cgit v1.2.3 From 9dd34948aaf631610355891a70cc55408eae840e Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 17 Jan 2007 22:11:27 +0100 Subject: [ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos Fix build glitches on ARM ... the only user of "rtc_lock" today is the optional PC-style "CMOS" RTC driver, the legacy SA1100 RTC driver is not even in the tree any more. Signed-off-by: David Brownell Signed-off-by: Russell King --- arch/arm/kernel/time.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c index 3c8cdcfe8d4a..3825acd6687d 100644 --- a/arch/arm/kernel/time.c +++ b/arch/arm/kernel/time.c @@ -40,12 +40,14 @@ */ struct sys_timer *system_timer; +#if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE) /* this needs a better home */ DEFINE_SPINLOCK(rtc_lock); -#ifdef CONFIG_SA1100_RTC_MODULE +#ifdef CONFIG_RTC_DRV_CMOS_MODULE EXPORT_SYMBOL(rtc_lock); #endif +#endif /* pc-style 'CMOS' RTC support */ /* change this if you have some constant time drift */ #define USECS_PER_JIFFY (1000000/HZ) -- cgit v1.2.3 From c6184e271db4948d4f6e07f271abeb8697a80eba Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sat, 17 Feb 2007 00:52:37 +0100 Subject: [ARM] 4214/2: S3C2410: Add Armzone QT2410 Patch from: Harald Welte Add support for the Armzone QT2410 system, with basic peripheral support for TFT display, SPI and LEDs. Signed-off-by: Harald Welte Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/Kconfig | 5 + arch/arm/mach-s3c2410/Makefile | 1 + arch/arm/mach-s3c2410/mach-qt2410.c | 448 ++++++++++++++++++++++++++++++++++++ 3 files changed, 454 insertions(+) create mode 100644 arch/arm/mach-s3c2410/mach-qt2410.c (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 016b53f5d6fc..d4b013b283c3 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -103,6 +103,11 @@ config MACH_VR1000 help Say Y here if you are using the Thorcom VR1000 board. +config MACH_QT2410 + bool "QT2410" + select CPU_S3C2410 + help + Say Y here if you are using the Armzone QT2410 endmenu diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index b33ac5b84773..9a3d3d24c084 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -28,3 +28,4 @@ obj-$(CONFIG_MACH_OTOM) += mach-otom.o obj-$(CONFIG_MACH_AML_M5900) += mach-amlm5900.o obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o obj-$(CONFIG_MACH_VR1000) += mach-vr1000.o usb-simtec.o +obj-$(CONFIG_MACH_QT2410) += mach-qt2410.o diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c new file mode 100644 index 000000000000..c6a41593de21 --- /dev/null +++ b/arch/arm/mach-s3c2410/mach-qt2410.c @@ -0,0 +1,448 @@ +/* linux/arch/arm/mach-s3c2410/mach-qt2410.c + * + * Copyright (C) 2006 by OpenMoko, Inc. + * Author: Harald Welte + * All rights reserved. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +static struct map_desc qt2410_iodesc[] __initdata = { + { 0xe0000000, __phys_to_pfn(S3C2410_CS3+0x01000000), SZ_1M, MT_DEVICE } +}; + +#define UCON S3C2410_UCON_DEFAULT +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + +static struct s3c2410_uartcfg smdk2410_uartcfgs[] = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + } +}; + +/* LCD driver info */ + +/* Configuration for 640x480 SHARP LQ080V3DG01 */ +static struct s3c2410fb_mach_info qt2410_biglcd_cfg __initdata = { + .regs = { + + .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | + S3C2410_LCDCON1_TFT | + S3C2410_LCDCON1_CLKVAL(0x01), /* HCLK/4 */ + + .lcdcon2 = S3C2410_LCDCON2_VBPD(18) | /* 19 */ + S3C2410_LCDCON2_LINEVAL(479) | + S3C2410_LCDCON2_VFPD(10) | /* 11 */ + S3C2410_LCDCON2_VSPW(14), /* 15 */ + + .lcdcon3 = S3C2410_LCDCON3_HBPD(43) | /* 44 */ + S3C2410_LCDCON3_HOZVAL(639) | /* 640 */ + S3C2410_LCDCON3_HFPD(115), /* 116 */ + + .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | + S3C2410_LCDCON4_HSPW(95), /* 96 */ + + .lcdcon5 = S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_PWREN | + S3C2410_LCDCON5_HWSWP, + }, + + .lpcsel = ((0xCE6) & ~7) | 1<<4, + + .width = 640, + .height = 480, + + .xres = { + .min = 640, + .max = 640, + .defval = 640, + }, + + .yres = { + .min = 480, + .max = 480, + .defval = 480, + }, + + .bpp = { + .min = 16, + .max = 16, + .defval = 16, + }, +}; + +/* Configuration for 480x640 toppoly TD028TTEC1 */ +static struct s3c2410fb_mach_info qt2410_prodlcd_cfg __initdata = { + .regs = { + + .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | + S3C2410_LCDCON1_TFT | + S3C2410_LCDCON1_CLKVAL(0x01), /* HCLK/4 */ + + .lcdcon2 = S3C2410_LCDCON2_VBPD(1) | /* 2 */ + S3C2410_LCDCON2_LINEVAL(639) |/* 640 */ + S3C2410_LCDCON2_VFPD(3) | /* 4 */ + S3C2410_LCDCON2_VSPW(1), /* 2 */ + + .lcdcon3 = S3C2410_LCDCON3_HBPD(7) | /* 8 */ + S3C2410_LCDCON3_HOZVAL(479) | /* 479 */ + S3C2410_LCDCON3_HFPD(23), /* 24 */ + + .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | + S3C2410_LCDCON4_HSPW(7), /* 8 */ + + .lcdcon5 = S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_PWREN | + S3C2410_LCDCON5_HWSWP, + }, + + .lpcsel = ((0xCE6) & ~7) | 1<<4, + + .width = 480, + .height = 640, + + .xres = { + .min = 480, + .max = 480, + .defval = 480, + }, + + .yres = { + .min = 640, + .max = 640, + .defval = 640, + }, + + .bpp = { + .min = 16, + .max = 16, + .defval = 16, + }, +}; + +/* Config for 240x320 LCD */ +static struct s3c2410fb_mach_info qt2410_lcd_cfg __initdata = { + .regs = { + + .lcdcon1 = S3C2410_LCDCON1_TFT16BPP | + S3C2410_LCDCON1_TFT | + S3C2410_LCDCON1_CLKVAL(0x04), + + .lcdcon2 = S3C2410_LCDCON2_VBPD(1) | + S3C2410_LCDCON2_LINEVAL(319) | + S3C2410_LCDCON2_VFPD(6) | + S3C2410_LCDCON2_VSPW(3), + + .lcdcon3 = S3C2410_LCDCON3_HBPD(12) | + S3C2410_LCDCON3_HOZVAL(239) | + S3C2410_LCDCON3_HFPD(7), + + .lcdcon4 = S3C2410_LCDCON4_MVAL(0) | + S3C2410_LCDCON4_HSPW(3), + + .lcdcon5 = S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_PWREN | + S3C2410_LCDCON5_HWSWP, + }, + + .lpcsel = ((0xCE6) & ~7) | 1<<4, + + .width = 240, + .height = 320, + + .xres = { + .min = 240, + .max = 240, + .defval = 240, + }, + + .yres = { + .min = 320, + .max = 320, + .defval = 320, + }, + + .bpp = { + .min = 16, + .max = 16, + .defval = 16, + }, +}; + +/* CS8900 */ + +static struct resource qt2410_cs89x0_resources[] = { + [0] = { + .start = 0x19000000, + .end = 0x19000000 + 16, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_EINT9, + .end = IRQ_EINT9, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device qt2410_cs89x0 = { + .name = "cirrus-cs89x0", + .num_resources = ARRAY_SIZE(qt2410_cs89x0_resources), + .resource = qt2410_cs89x0_resources, +}; + +/* LED */ + +static struct s3c24xx_led_platdata qt2410_pdata_led = { + .gpio = S3C2410_GPB0, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led", + .def_trigger = "timer", +}; + +static struct platform_device qt2410_led = { + .name = "s3c24xx_led", + .id = 0, + .dev = { + .platform_data = &qt2410_pdata_led, + }, +}; + +/* SPI */ + +static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs) +{ + switch (cs) { + case BITBANG_CS_ACTIVE: + s3c2410_gpio_setpin(S3C2410_GPB5, 0); + break; + case BITBANG_CS_INACTIVE: + s3c2410_gpio_setpin(S3C2410_GPB5, 1); + break; + } +} + +static struct s3c2410_spigpio_info spi_gpio_cfg = { + .pin_clk = S3C2410_GPG7, + .pin_mosi = S3C2410_GPG6, + .pin_miso = S3C2410_GPG5, + .chip_select = &spi_gpio_cs, +}; + + +static struct platform_device qt2410_spi = { + .name = "s3c24xx-spi-gpio", + .id = 1, + .dev = { + .platform_data = &spi_gpio_cfg, + }, +}; + +/* Board devices */ + +static struct platform_device *qt2410_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_lcd, + &s3c_device_wdt, + &s3c_device_i2c, + &s3c_device_iis, + &s3c_device_sdi, + &s3c_device_usbgadget, + &qt2410_spi, + &qt2410_cs89x0, + &qt2410_led, +}; + +static struct s3c24xx_board qt2410_board __initdata = { + .devices = qt2410_devices, + .devices_count = ARRAY_SIZE(qt2410_devices) +}; + +static struct mtd_partition qt2410_nand_part[] = { + [0] = { + .name = "U-Boot", + .size = 0x30000, + .offset = 0, + }, + [1] = { + .name = "U-Boot environment", + .offset = 0x30000, + .size = 0x4000, + }, + [2] = { + .name = "kernel", + .offset = 0x34000, + .size = SZ_2M, + }, + [3] = { + .name = "initrd", + .offset = 0x234000, + .size = SZ_4M, + }, + [4] = { + .name = "jffs2", + .offset = 0x634000, + .size = 0x39cc000, + }, +}; + +static struct s3c2410_nand_set qt2410_nand_sets[] = { + [0] = { + .name = "NAND", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(qt2410_nand_part), + .partitions = qt2410_nand_part, + }, +}; + +/* choose a set of timings which should suit most 512Mbit + * chips and beyond. + */ + +static struct s3c2410_platform_nand qt2410_nand_info = { + .tacls = 20, + .twrph0 = 60, + .twrph1 = 20, + .nr_sets = ARRAY_SIZE(qt2410_nand_sets), + .sets = qt2410_nand_sets, +}; + +/* UDC */ + +static struct s3c2410_udc_mach_info qt2410_udc_cfg = { +}; + +static char tft_type = 's'; + +static int __init qt2410_tft_setup(char *str) +{ + tft_type = str[0]; + return 1; +} + +__setup("tft=", qt2410_tft_setup); + +static void __init qt2410_map_io(void) +{ + s3c24xx_init_io(qt2410_iodesc, ARRAY_SIZE(qt2410_iodesc)); + s3c24xx_init_clocks(12*1000*1000); + s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs)); + s3c24xx_set_board(&qt2410_board); +} + +static void __init qt2410_machine_init(void) +{ + s3c_device_nand.dev.platform_data = &qt2410_nand_info; + + switch (tft_type) { + case 'p': /* production */ + s3c24xx_fb_set_platdata(&qt2410_prodlcd_cfg); + break; + case 'b': /* big */ + s3c24xx_fb_set_platdata(&qt2410_biglcd_cfg); + break; + case 's': /* small */ + default: + s3c24xx_fb_set_platdata(&qt2410_lcd_cfg); + break; + } + + s3c2410_gpio_cfgpin(S3C2410_GPB0, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB0, 1); + + s3c24xx_udc_set_platdata(&qt2410_udc_cfg); + + s3c2410_gpio_cfgpin(S3C2410_GPB5, S3C2410_GPIO_OUTPUT); + + s3c2410_pm_init(); +} + +MACHINE_START(QT2410, "QT2410") + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = qt2410_map_io, + .init_irq = s3c24xx_init_irq, + .init_machine = qt2410_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END + + -- cgit v1.2.3 From ca83b0bcf875cd20cb5226d1fc7e828d9e0cc269 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Sat, 17 Feb 2007 03:37:02 +0100 Subject: [ARM] 4216/1: add .gitignore entries for ARM specific files Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/boot/.gitignore | 2 ++ arch/arm/boot/compressed/.gitignore | 1 + include/asm-arm/.gitignore | 2 ++ 3 files changed, 5 insertions(+) create mode 100644 arch/arm/boot/.gitignore create mode 100644 arch/arm/boot/compressed/.gitignore create mode 100644 include/asm-arm/.gitignore (limited to 'arch') diff --git a/arch/arm/boot/.gitignore b/arch/arm/boot/.gitignore new file mode 100644 index 000000000000..171a0853caf8 --- /dev/null +++ b/arch/arm/boot/.gitignore @@ -0,0 +1,2 @@ +Image +zImage diff --git a/arch/arm/boot/compressed/.gitignore b/arch/arm/boot/compressed/.gitignore new file mode 100644 index 000000000000..aefee20cbf98 --- /dev/null +++ b/arch/arm/boot/compressed/.gitignore @@ -0,0 +1 @@ +piggy.gz diff --git a/include/asm-arm/.gitignore b/include/asm-arm/.gitignore new file mode 100644 index 000000000000..e02c15d158fc --- /dev/null +++ b/include/asm-arm/.gitignore @@ -0,0 +1,2 @@ +arch +mach-types.h -- cgit v1.2.3 From 3d9dd6bdbd6765a86736ead09009daf29382a6f2 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sat, 17 Feb 2007 14:02:37 +0100 Subject: [ARM] 4217/1: S3C24XX: remove the dma channel show at startup Remove the DMA code's channel printing at startup as this is firstly a waste of console output on initialsaion, and secondly is going to be obsolete once the S3C2443 DMA code has been merged Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/plat-s3c24xx/dma.c | 14 -------------- 1 file changed, 14 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c index 44e39438b9d8..929265aab7dd 100644 --- a/arch/arm/plat-s3c24xx/dma.c +++ b/arch/arm/plat-s3c24xx/dma.c @@ -1426,22 +1426,8 @@ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) return dmach; } -static void s3c24xx_dma_show_ch(struct s3c24xx_dma_map *map, int ch) -{ - /* show the channel configuration */ - - printk("%2d: %20s, channels %c%c%c%c\n", ch, map->name, - (is_channel_valid(map->channels[0]) ? '0' : '-'), - (is_channel_valid(map->channels[1]) ? '1' : '-'), - (is_channel_valid(map->channels[2]) ? '2' : '-'), - (is_channel_valid(map->channels[3]) ? '3' : '-')); -} - static int s3c24xx_dma_check_entry(struct s3c24xx_dma_map *map, int ch) { - if (1) - s3c24xx_dma_show_ch(map, ch); - return 0; } -- cgit v1.2.3 From 64f33beafbaae55d116e933e8eae6b068fba617f Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sat, 17 Feb 2007 14:04:33 +0100 Subject: [ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443 Update the Kconfig of arch/arm/mach-s3c2443 to add the CONFIG_CPU_S3C2443 to the list of config variabls which mean CONFIG_CPU_S3C2412_ONLY cannot be set Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2412/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig index 6d629de84cdb..befc5fdbb613 100644 --- a/arch/arm/mach-s3c2412/Kconfig +++ b/arch/arm/mach-s3c2412/Kconfig @@ -15,7 +15,7 @@ config CPU_S3C2412 config CPU_S3C2412_ONLY bool depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \ - !CPU_S3C2440 && !CPU_S3C2442 && CPU_S3C2412 + !CPU_S3C2440 && !CPU_S3C2442 && !CPU_S3C2443 && CPU_S3C2412 default y if CPU_S3C2412 config S3C2412_DMA -- cgit v1.2.3 From 48adbcf33b6087727a2db0b517c994a7ecfbeb0c Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sat, 17 Feb 2007 15:37:14 +0100 Subject: [ARM] 4220/1: S3C24XX: DMA system initialised from sysdev This patch gets the DMA system for the S3C24XX ready for the S3C2443, which requires 6 dma channels at a different stride, and different base IRQ. The DMA system is now initialised from the same drivers which apply the DMA mappings, as well as removing the DMA sysdev intialisation out of the main init code (which is now being called from a sysdev probe, so cannot add a new sysdev) Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2410/dma.c | 11 +++--- arch/arm/mach-s3c2412/dma.c | 1 + arch/arm/mach-s3c2440/dma.c | 3 +- arch/arm/plat-s3c24xx/dma.c | 77 ++++++++++++++++++++++++++------------ include/asm-arm/plat-s3c24xx/dma.h | 7 ++++ 5 files changed, 69 insertions(+), 30 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c index 6b3452680755..67d1ad363973 100644 --- a/arch/arm/mach-s3c2410/dma.c +++ b/arch/arm/mach-s3c2410/dma.c @@ -19,9 +19,9 @@ #include #include -#include #include +#include #include #include @@ -147,6 +147,7 @@ static struct s3c24xx_dma_order __initdata s3c2410_dma_order = { static int s3c2410_dma_add(struct sys_device *sysdev) { + s3c2410_dma_init(); s3c24xx_dma_order_set(&s3c2410_dma_order); return s3c24xx_dma_init_map(&s3c2410_dma_sel); } @@ -156,12 +157,12 @@ static struct sysdev_driver s3c2410_dma_driver = { .add = s3c2410_dma_add, }; -static int __init s3c2410_dma_init(void) +static int __init s3c2410_dma_drvinit(void) { return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_dma_driver); } -arch_initcall(s3c2410_dma_init); +arch_initcall(s3c2410_dma_drvinit); #endif #if defined(CONFIG_CPU_S3C2442) @@ -170,11 +171,11 @@ static struct sysdev_driver s3c2442_dma_driver = { .add = s3c2410_dma_add, }; -static int __init s3c2442_dma_init(void) +static int __init s3c2442_dma_drvinit(void) { return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_dma_driver); } -arch_initcall(s3c2442_dma_init); +arch_initcall(s3c2442_dma_drvinit); #endif diff --git a/arch/arm/mach-s3c2412/dma.c b/arch/arm/mach-s3c2412/dma.c index 28b598287fae..d0f4695c09d9 100644 --- a/arch/arm/mach-s3c2412/dma.c +++ b/arch/arm/mach-s3c2412/dma.c @@ -146,6 +146,7 @@ static struct s3c24xx_dma_selection __initdata s3c2412_dma_sel = { static int s3c2412_dma_add(struct sys_device *sysdev) { + s3c2410_dma_init(); return s3c24xx_dma_init_map(&s3c2412_dma_sel); } diff --git a/arch/arm/mach-s3c2440/dma.c b/arch/arm/mach-s3c2440/dma.c index 2bb2926554c8..cd035a3ec878 100644 --- a/arch/arm/mach-s3c2440/dma.c +++ b/arch/arm/mach-s3c2440/dma.c @@ -19,8 +19,8 @@ #include #include -#include +#include #include #include @@ -192,6 +192,7 @@ static struct s3c24xx_dma_order __initdata s3c2440_dma_order = { static int s3c2440_dma_add(struct sys_device *sysdev) { + s3c2410_dma_init(); s3c24xx_dma_order_set(&s3c2440_dma_order); return s3c24xx_dma_init_map(&s3c2440_dma_sel); } diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c index 929265aab7dd..4540a806f522 100644 --- a/arch/arm/plat-s3c24xx/dma.c +++ b/arch/arm/plat-s3c24xx/dma.c @@ -42,6 +42,8 @@ static void __iomem *dma_base; static struct kmem_cache *dma_kmem; +static int dma_channels; + struct s3c24xx_dma_selection dma_sel; /* dma channel state information */ @@ -1278,7 +1280,42 @@ static void s3c2410_dma_cache_ctor(void *p, struct kmem_cache *c, unsigned long /* initialisation code */ -static int __init s3c2410_init_dma(void) +int __init s3c24xx_dma_sysclass_init(void) +{ + int ret = sysdev_class_register(&dma_sysclass); + + if (ret != 0) + printk(KERN_ERR "dma sysclass registration failed\n"); + + return ret; +} + +core_initcall(s3c24xx_dma_sysclass_init); + +int __init s3c24xx_dma_sysdev_register(void) +{ + struct s3c2410_dma_chan *cp = s3c2410_chans; + int channel, ret; + + for (channel = 0; channel < dma_channels; cp++, channel++) { + cp->dev.cls = &dma_sysclass; + cp->dev.id = channel; + ret = sysdev_register(&cp->dev); + + if (ret) { + printk(KERN_ERR "error registering dev for dma %d\n", + channel); + return ret; + } + } + + return 0; +} + +late_initcall(s3c24xx_dma_sysdev_register); + +int __init s3c24xx_dma_init(unsigned int channels, unsigned int irq, + unsigned int stride) { struct s3c2410_dma_chan *cp; int channel; @@ -1286,21 +1323,16 @@ static int __init s3c2410_init_dma(void) printk("S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics\n"); - dma_base = ioremap(S3C24XX_PA_DMA, 0x200); + dma_channels = channels; + + dma_base = ioremap(S3C24XX_PA_DMA, stride * channels); if (dma_base == NULL) { printk(KERN_ERR "dma failed to remap register block\n"); return -ENOMEM; } - printk("Registering sysclass\n"); - - ret = sysdev_class_register(&dma_sysclass); - if (ret != 0) { - printk(KERN_ERR "dma sysclass registration failed\n"); - goto err; - } - - dma_kmem = kmem_cache_create("dma_desc", sizeof(struct s3c2410_dma_buf), 0, + dma_kmem = kmem_cache_create("dma_desc", + sizeof(struct s3c2410_dma_buf), 0, SLAB_HWCACHE_ALIGN, s3c2410_dma_cache_ctor, NULL); @@ -1310,15 +1342,15 @@ static int __init s3c2410_init_dma(void) goto err; } - for (channel = 0; channel < S3C2410_DMA_CHANNELS; channel++) { + for (channel = 0; channel < channels; channel++) { cp = &s3c2410_chans[channel]; memset(cp, 0, sizeof(struct s3c2410_dma_chan)); /* dma channel irqs are in order.. */ cp->number = channel; - cp->irq = channel + IRQ_DMA0; - cp->regs = dma_base + (channel*0x40); + cp->irq = channel + irq; + cp->regs = dma_base + (channel * stride); /* point current stats somewhere */ cp->stats = &cp->stats_store; @@ -1328,12 +1360,6 @@ static int __init s3c2410_init_dma(void) cp->load_timeout = 1<<18; - /* register system device */ - - cp->dev.cls = &dma_sysclass; - cp->dev.id = channel; - ret = sysdev_register(&cp->dev); - printk("DMA channel %d at %p, irq %d\n", cp->number, cp->regs, cp->irq); } @@ -1347,7 +1373,10 @@ static int __init s3c2410_init_dma(void) return ret; } -core_initcall(s3c2410_init_dma); +int s3c2410_dma_init(void) +{ + return s3c24xx_dma_init(4, IRQ_DMA0, 0x40); +} static inline int is_channel_valid(unsigned int channel) { @@ -1384,7 +1413,7 @@ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) if (dma_order) { ord = &dma_order->channels[channel]; - for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) { + for (ch = 0; ch < dma_channels; ch++) { if (!is_channel_valid(ord->list[ch])) continue; @@ -1400,7 +1429,7 @@ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) /* second, search the channel map for first free */ - for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) { + for (ch = 0; ch < dma_channels; ch++) { if (!is_channel_valid(ch_map->channels[ch])) continue; @@ -1410,7 +1439,7 @@ struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel) } } - if (ch >= S3C2410_DMA_CHANNELS) + if (ch >= dma_channels) return NULL; /* update our channel mapping */ diff --git a/include/asm-arm/plat-s3c24xx/dma.h b/include/asm-arm/plat-s3c24xx/dma.h index 15e140c2d4fc..2c59406435e5 100644 --- a/include/asm-arm/plat-s3c24xx/dma.h +++ b/include/asm-arm/plat-s3c24xx/dma.h @@ -68,3 +68,10 @@ struct s3c24xx_dma_order { }; extern int s3c24xx_dma_order_set(struct s3c24xx_dma_order *map); + +/* DMA init code, called from the cpu support code */ + +extern int s3c2410_dma_init(void); + +extern int s3c24xx_dma_init(unsigned int channels, unsigned int irq, + unsigned int stride); -- cgit v1.2.3 From f8271e57569d1a2e7061f1754a5bb797a13b302d Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sat, 17 Feb 2007 15:41:50 +0100 Subject: [ARM] 4221/1: S3C2443: DMA support Add initialisation and mappings for S3C2443 DMA system Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2443/Kconfig | 6 ++ arch/arm/mach-s3c2443/Makefile | 2 + arch/arm/mach-s3c2443/dma.c | 180 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 188 insertions(+) create mode 100644 arch/arm/mach-s3c2443/dma.c (limited to 'arch') diff --git a/arch/arm/mach-s3c2443/Kconfig b/arch/arm/mach-s3c2443/Kconfig index 722bdea3c193..079c1effd3d2 100644 --- a/arch/arm/mach-s3c2443/Kconfig +++ b/arch/arm/mach-s3c2443/Kconfig @@ -12,6 +12,12 @@ config CPU_S3C2443 help Support for the S3C2443 SoC from the S3C24XX line +config S3C2443_DMA + bool + depends on CPU_S3C2443 + help + Internal config node for S3C2443 DMA support + menu "S3C2443 Machines" config MACH_SMDK2443 diff --git a/arch/arm/mach-s3c2443/Makefile b/arch/arm/mach-s3c2443/Makefile index a878076beecd..d1843c9eb8bd 100644 --- a/arch/arm/mach-s3c2443/Makefile +++ b/arch/arm/mach-s3c2443/Makefile @@ -13,6 +13,8 @@ obj-$(CONFIG_CPU_S3C2443) += s3c2443.o obj-$(CONFIG_CPU_S3C2443) += irq.o obj-$(CONFIG_CPU_S3C2443) += clock.o +obj-$(CONFIG_S3C2443_DMA) += dma.o + # Machine support obj-$(CONFIG_MACH_SMDK2443) += mach-smdk2443.o diff --git a/arch/arm/mach-s3c2443/dma.c b/arch/arm/mach-s3c2443/dma.c new file mode 100644 index 000000000000..f70e8ccffc3d --- /dev/null +++ b/arch/arm/mach-s3c2443/dma.c @@ -0,0 +1,180 @@ +/* linux/arch/arm/mach-s3c2443/dma.c + * + * Copyright (c) 2007 Simtec Electronics + * Ben Dooks + * + * S3C2443 DMA selection + * + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#define MAP(x) { \ + [0] = (x) | DMA_CH_VALID, \ + [1] = (x) | DMA_CH_VALID, \ + [2] = (x) | DMA_CH_VALID, \ + [3] = (x) | DMA_CH_VALID, \ + [4] = (x) | DMA_CH_VALID, \ + [5] = (x) | DMA_CH_VALID, \ + } + +static struct s3c24xx_dma_map __initdata s3c2443_dma_mappings[] = { + [DMACH_XD0] = { + .name = "xdreq0", + .channels = MAP(S3C2443_DMAREQSEL_XDREQ0), + }, + [DMACH_XD1] = { + .name = "xdreq1", + .channels = MAP(S3C2443_DMAREQSEL_XDREQ1), + }, + [DMACH_SDI] = { + .name = "sdi", + .channels = MAP(S3C2443_DMAREQSEL_SDI), + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_SPI0] = { + .name = "spi0", + .channels = MAP(S3C2443_DMAREQSEL_SPI0TX), + .hw_addr.to = S3C2410_PA_SPI + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + S3C2410_SPRDAT, + }, + [DMACH_SPI1] = { + .name = "spi1", + .channels = MAP(S3C2443_DMAREQSEL_SPI1TX), + .hw_addr.to = S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT, + .hw_addr.from = S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT, + }, + [DMACH_UART0] = { + .name = "uart0", + .channels = MAP(S3C2443_DMAREQSEL_UART0_0), + .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, + }, + [DMACH_UART1] = { + .name = "uart1", + .channels = MAP(S3C2443_DMAREQSEL_UART1_0), + .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, + }, + [DMACH_UART2] = { + .name = "uart2", + .channels = MAP(S3C2443_DMAREQSEL_UART2_0), + .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, + }, + [DMACH_UART3] = { + .name = "uart3", + .channels = MAP(S3C2443_DMAREQSEL_UART3_0), + .hw_addr.to = S3C2443_PA_UART3 + S3C2410_UTXH, + .hw_addr.from = S3C2443_PA_UART3 + S3C2410_URXH, + }, + [DMACH_UART0_SRC2] = { + .name = "uart0", + .channels = MAP(S3C2443_DMAREQSEL_UART0_1), + .hw_addr.to = S3C2410_PA_UART0 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART0 + S3C2410_URXH, + }, + [DMACH_UART1_SRC2] = { + .name = "uart1", + .channels = MAP(S3C2443_DMAREQSEL_UART1_1), + .hw_addr.to = S3C2410_PA_UART1 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART1 + S3C2410_URXH, + }, + [DMACH_UART2_SRC2] = { + .name = "uart2", + .channels = MAP(S3C2443_DMAREQSEL_UART2_1), + .hw_addr.to = S3C2410_PA_UART2 + S3C2410_UTXH, + .hw_addr.from = S3C2410_PA_UART2 + S3C2410_URXH, + }, + [DMACH_UART3_SRC2] = { + .name = "uart3", + .channels = MAP(S3C2443_DMAREQSEL_UART3_1), + .hw_addr.to = S3C2443_PA_UART3 + S3C2410_UTXH, + .hw_addr.from = S3C2443_PA_UART3 + S3C2410_URXH, + }, + [DMACH_TIMER] = { + .name = "timer", + .channels = MAP(S3C2443_DMAREQSEL_TIMER), + }, + [DMACH_I2S_IN] = { + .name = "i2s-sdi", + .channels = MAP(S3C2443_DMAREQSEL_I2SRX), + .hw_addr.from = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_I2S_OUT] = { + .name = "i2s-sdo", + .channels = MAP(S3C2443_DMAREQSEL_I2STX), + .hw_addr.to = S3C2410_PA_IIS + S3C2410_IISFIFO, + }, + [DMACH_PCM_IN] = { + .name = "pcm-in", + .channels = MAP(S3C2443_DMAREQSEL_PCMIN), + .hw_addr.from = S3C2440_PA_AC97 + S3C_AC97_PCM_DATA, + }, + [DMACH_PCM_OUT] = { + .name = "pcm-out", + .channels = MAP(S3C2443_DMAREQSEL_PCMOUT), + .hw_addr.to = S3C2440_PA_AC97 + S3C_AC97_PCM_DATA, + }, + [DMACH_MIC_IN] = { + .name = "mic-in", + .channels = MAP(S3C2443_DMAREQSEL_MICIN), + .hw_addr.from = S3C2440_PA_AC97 + S3C_AC97_MIC_DATA, + }, +}; + +static void s3c2443_dma_select(struct s3c2410_dma_chan *chan, + struct s3c24xx_dma_map *map) +{ + writel(map->channels[0] | S3C2443_DMAREQSEL_HW, + chan->regs + S3C2443_DMA_DMAREQSEL); +} + +static struct s3c24xx_dma_selection __initdata s3c2443_dma_sel = { + .select = s3c2443_dma_select, + .dcon_mask = 0, + .map = s3c2443_dma_mappings, + .map_size = ARRAY_SIZE(s3c2443_dma_mappings), +}; + +static int s3c2443_dma_add(struct sys_device *sysdev) +{ + s3c24xx_dma_init(6, IRQ_S3C2443_DMA0, 0x100); + return s3c24xx_dma_init_map(&s3c2443_dma_sel); +} + +static struct sysdev_driver s3c2443_dma_driver = { + .add = s3c2443_dma_add, +}; + +static int __init s3c2443_dma_init(void) +{ + return sysdev_driver_register(&s3c2443_sysclass, &s3c2443_dma_driver); +} + +arch_initcall(s3c2443_dma_init); -- cgit v1.2.3 From 78c2644feccf78ecab8e9413d2fac83cda091bae Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Sat, 17 Feb 2007 16:41:12 +0100 Subject: [ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM S3C2443_PM is not defined in our Kconfig, so remove the reference from CPU_S3C2443 to stop the configuration process warning about it. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/mach-s3c2443/Kconfig | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c2443/Kconfig b/arch/arm/mach-s3c2443/Kconfig index 079c1effd3d2..c649bb2e7ce8 100644 --- a/arch/arm/mach-s3c2443/Kconfig +++ b/arch/arm/mach-s3c2443/Kconfig @@ -7,7 +7,6 @@ config CPU_S3C2443 bool depends on ARCH_S3C2410 - select S3C2443_PM if PM select S3C2443_DMA if S3C2410_DMA help Support for the S3C2443 SoC from the S3C24XX line -- cgit v1.2.3 From 9918cda52368ec3df5bb6bc1630ba8c070ad9fdd Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Fri, 16 Feb 2007 15:36:55 +0100 Subject: [ARM] 4210/1: base for new machine type "NetSilicon NS9360" Signed-off-by: Uwe Kleine-König Signed-off-by: Russell King --- arch/arm/Kconfig | 10 ++ arch/arm/Makefile | 10 +- arch/arm/mach-ns9xxx/Kconfig | 21 +++ arch/arm/mach-ns9xxx/Makefile | 5 + arch/arm/mach-ns9xxx/Makefile.boot | 2 + arch/arm/mach-ns9xxx/board-a9m9750dev.c | 199 +++++++++++++++++++++ arch/arm/mach-ns9xxx/board-a9m9750dev.h | 15 ++ arch/arm/mach-ns9xxx/generic.c | 42 +++++ arch/arm/mach-ns9xxx/generic.h | 19 ++ arch/arm/mach-ns9xxx/irq.c | 94 ++++++++++ arch/arm/mach-ns9xxx/mach-cc9p9360dev.c | 41 +++++ arch/arm/mach-ns9xxx/time.c | 88 +++++++++ arch/arm/mm/Kconfig | 4 +- include/asm-arm/arch-ns9xxx/board.h | 18 ++ include/asm-arm/arch-ns9xxx/clock.h | 37 ++++ include/asm-arm/arch-ns9xxx/debug-macro.S | 22 +++ include/asm-arm/arch-ns9xxx/dma.h | 14 ++ include/asm-arm/arch-ns9xxx/entry-macro.S | 22 +++ include/asm-arm/arch-ns9xxx/hardware.h | 67 +++++++ include/asm-arm/arch-ns9xxx/io.h | 20 +++ include/asm-arm/arch-ns9xxx/irqs.h | 85 +++++++++ include/asm-arm/arch-ns9xxx/memory.h | 27 +++ include/asm-arm/arch-ns9xxx/processor.h | 18 ++ include/asm-arm/arch-ns9xxx/regs-bbu.h | 21 +++ .../asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h | 24 +++ include/asm-arm/arch-ns9xxx/regs-mem.h | 135 ++++++++++++++ include/asm-arm/arch-ns9xxx/regs-sys.h | 157 ++++++++++++++++ include/asm-arm/arch-ns9xxx/system.h | 34 ++++ include/asm-arm/arch-ns9xxx/timex.h | 20 +++ include/asm-arm/arch-ns9xxx/uncompress.h | 35 ++++ include/asm-arm/arch-ns9xxx/vmalloc.h | 16 ++ 31 files changed, 1316 insertions(+), 6 deletions(-) create mode 100644 arch/arm/mach-ns9xxx/Kconfig create mode 100644 arch/arm/mach-ns9xxx/Makefile create mode 100644 arch/arm/mach-ns9xxx/Makefile.boot create mode 100644 arch/arm/mach-ns9xxx/board-a9m9750dev.c create mode 100644 arch/arm/mach-ns9xxx/board-a9m9750dev.h create mode 100644 arch/arm/mach-ns9xxx/generic.c create mode 100644 arch/arm/mach-ns9xxx/generic.h create mode 100644 arch/arm/mach-ns9xxx/irq.c create mode 100644 arch/arm/mach-ns9xxx/mach-cc9p9360dev.c create mode 100644 arch/arm/mach-ns9xxx/time.c create mode 100644 include/asm-arm/arch-ns9xxx/board.h create mode 100644 include/asm-arm/arch-ns9xxx/clock.h create mode 100644 include/asm-arm/arch-ns9xxx/debug-macro.S create mode 100644 include/asm-arm/arch-ns9xxx/dma.h create mode 100644 include/asm-arm/arch-ns9xxx/entry-macro.S create mode 100644 include/asm-arm/arch-ns9xxx/hardware.h create mode 100644 include/asm-arm/arch-ns9xxx/io.h create mode 100644 include/asm-arm/arch-ns9xxx/irqs.h create mode 100644 include/asm-arm/arch-ns9xxx/memory.h create mode 100644 include/asm-arm/arch-ns9xxx/processor.h create mode 100644 include/asm-arm/arch-ns9xxx/regs-bbu.h create mode 100644 include/asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h create mode 100644 include/asm-arm/arch-ns9xxx/regs-mem.h create mode 100644 include/asm-arm/arch-ns9xxx/regs-sys.h create mode 100644 include/asm-arm/arch-ns9xxx/system.h create mode 100644 include/asm-arm/arch-ns9xxx/timex.h create mode 100644 include/asm-arm/arch-ns9xxx/uncompress.h create mode 100644 include/asm-arm/arch-ns9xxx/vmalloc.h (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6783c2e5512d..c84350868c23 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -271,6 +271,14 @@ config ARCH_L7200 If you have any questions or comments about the Linux kernel port to this board, send e-mail to . +config ARCH_NS9XXX + bool "NetSilicon NS9xxx" + help + Say Y here if you intend to run this kernel on a NetSilicon NS9xxx + System. + + + config ARCH_PNX4008 bool "Philips Nexperia PNX4008 Mobile" help @@ -381,6 +389,8 @@ source "arch/arm/mach-at91rm9200/Kconfig" source "arch/arm/mach-netx/Kconfig" +source "arch/arm/mach-ns9xxx/Kconfig" + # Definitions to make life easier config ARCH_ACORN bool diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 000f1100b553..52d119422293 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -124,10 +124,12 @@ endif machine-$(CONFIG_ARCH_H720X) := h720x machine-$(CONFIG_ARCH_AAEC2000) := aaec2000 machine-$(CONFIG_ARCH_REALVIEW) := realview - machine-$(CONFIG_ARCH_AT91) := at91rm9200 - machine-$(CONFIG_ARCH_EP93XX) := ep93xx - machine-$(CONFIG_ARCH_PNX4008) := pnx4008 - machine-$(CONFIG_ARCH_NETX) := netx + machine-$(CONFIG_ARCH_AT91) := at91rm9200 + machine-$(CONFIG_ARCH_EP93XX) := ep93xx + machine-$(CONFIG_ARCH_PNX4008) := pnx4008 + machine-$(CONFIG_ARCH_NETX) := netx + machine-$(CONFIG_ARCH_NS9XXX) := ns9xxx + textofs-$(CONFIG_ARCH_NS9XXX) := 0x00108000 ifeq ($(CONFIG_ARCH_EBSA110),y) # This is what happens if you forget the IOCS16 line. diff --git a/arch/arm/mach-ns9xxx/Kconfig b/arch/arm/mach-ns9xxx/Kconfig new file mode 100644 index 000000000000..8175ba92a2fa --- /dev/null +++ b/arch/arm/mach-ns9xxx/Kconfig @@ -0,0 +1,21 @@ +if ARCH_NS9XXX + +menu "NS9xxx Implementations" + +config MACH_CC9P9360DEV + bool "Connect Core 9P 9360 on an A9M9750 Devboard" + select PROCESSOR_NS9360 + select BOARD_A9M9750DEV + help + Say Y here if you are using the Digi Connect Core 9P 9360 + on an A9M9750 Development Board. + +config PROCESSOR_NS9360 + bool + +config BOARD_A9M9750DEV + bool + +endmenu + +endif diff --git a/arch/arm/mach-ns9xxx/Makefile b/arch/arm/mach-ns9xxx/Makefile new file mode 100644 index 000000000000..91e945f5e16d --- /dev/null +++ b/arch/arm/mach-ns9xxx/Makefile @@ -0,0 +1,5 @@ +obj-y := irq.o time.o generic.o + +obj-$(CONFIG_MACH_CC9P9360DEV) += mach-cc9p9360dev.o + +obj-$(CONFIG_BOARD_A9M9750DEV) += board-a9m9750dev.o diff --git a/arch/arm/mach-ns9xxx/Makefile.boot b/arch/arm/mach-ns9xxx/Makefile.boot new file mode 100644 index 000000000000..75ed64e90fa4 --- /dev/null +++ b/arch/arm/mach-ns9xxx/Makefile.boot @@ -0,0 +1,2 @@ +zreladdr-y := 0x108000 +params_phys-y := 0x100 diff --git a/arch/arm/mach-ns9xxx/board-a9m9750dev.c b/arch/arm/mach-ns9xxx/board-a9m9750dev.c new file mode 100644 index 000000000000..25289884a607 --- /dev/null +++ b/arch/arm/mach-ns9xxx/board-a9m9750dev.c @@ -0,0 +1,199 @@ +/* + * arch/arm/mach-ns9xxx/board-a9m9750dev.c + * + * Copyright (C) 2006,2007 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include +#include + +#include + +#include +#include +#include +#include +#include + +#include "board-a9m9750dev.h" + +static struct map_desc board_a9m9750dev_io_desc[] __initdata = { + { /* FPGA on CS0 */ + .virtual = io_p2v(NS9XXX_CSxSTAT_PHYS(0)), + .pfn = __phys_to_pfn(NS9XXX_CSxSTAT_PHYS(0)), + .length = NS9XXX_CS0STAT_LENGTH, + .type = MT_DEVICE, + }, +}; + +void __init board_a9m9750dev_map_io(void) +{ + iotable_init(board_a9m9750dev_io_desc, + ARRAY_SIZE(board_a9m9750dev_io_desc)); +} + +static void a9m9750dev_fpga_ack_irq(unsigned int irq) +{ + /* nothing */ +} + +static void a9m9750dev_fpga_mask_irq(unsigned int irq) +{ + FPGA_IER &= ~(1 << (irq - FPGA_IRQ(0))); +} + +static void a9m9750dev_fpga_maskack_irq(unsigned int irq) +{ + a9m9750dev_fpga_mask_irq(irq); + a9m9750dev_fpga_ack_irq(irq); +} + +static void a9m9750dev_fpga_unmask_irq(unsigned int irq) +{ + FPGA_IER |= 1 << (irq - FPGA_IRQ(0)); +} + +static struct irq_chip a9m9750dev_fpga_chip = { + .ack = a9m9750dev_fpga_ack_irq, + .mask = a9m9750dev_fpga_mask_irq, + .mask_ack = a9m9750dev_fpga_maskack_irq, + .unmask = a9m9750dev_fpga_unmask_irq, +}; + +static void a9m9750dev_fpga_demux_handler(unsigned int irq, + struct irq_desc *desc) +{ + int stat = FPGA_ISR; + + while (stat != 0) { + int irqno = fls(stat) - 1; + + stat &= ~(1 << irqno); + + desc = irq_desc + FPGA_IRQ(irqno); + + desc_handle_irq(irqno, desc); + } +} + +void __init board_a9m9750dev_init_irq(void) +{ + u32 reg; + int i; + + /* + * configure gpio for IRQ_EXT2 + * use GPIO 11, because GPIO 32 is used for the LCD + */ + /* XXX: proper GPIO handling */ + BBU_GC(2) &= ~0x2000; + + for (i = FPGA_IRQ(0); i <= FPGA_IRQ(7); ++i) { + set_irq_chip(i, &a9m9750dev_fpga_chip); + set_irq_handler(i, handle_level_irq); + set_irq_flags(i, IRQF_VALID); + } + + /* IRQ_EXT2: level sensitive + active low */ + reg = SYS_EIC(2); + REGSET(reg, SYS_EIC, PLTY, AL); + REGSET(reg, SYS_EIC, LVEDG, LEVEL); + SYS_EIC(2) = reg; + + set_irq_chained_handler(IRQ_EXT2, + a9m9750dev_fpga_demux_handler); +} + +static struct plat_serial8250_port board_a9m9750dev_serial8250_port[] = { + { + .iobase = FPGA_UARTA_BASE, + .membase = (unsigned char*)FPGA_UARTA_BASE, + .mapbase = FPGA_UARTA_BASE, + .irq = IRQ_FPGA_UARTA, + .iotype = UPIO_MEM, + .uartclk = 18432000, + .regshift = 0, + .flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ, + }, { + .iobase = FPGA_UARTB_BASE, + .membase = (unsigned char*)FPGA_UARTB_BASE, + .mapbase = FPGA_UARTB_BASE, + .irq = IRQ_FPGA_UARTB, + .iotype = UPIO_MEM, + .uartclk = 18432000, + .regshift = 0, + .flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ, + }, { + .iobase = FPGA_UARTC_BASE, + .membase = (unsigned char*)FPGA_UARTC_BASE, + .mapbase = FPGA_UARTC_BASE, + .irq = IRQ_FPGA_UARTC, + .iotype = UPIO_MEM, + .uartclk = 18432000, + .regshift = 0, + .flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ, + }, { + .iobase = FPGA_UARTD_BASE, + .membase = (unsigned char*)FPGA_UARTD_BASE, + .mapbase = FPGA_UARTD_BASE, + .irq = IRQ_FPGA_UARTD, + .iotype = UPIO_MEM, + .uartclk = 18432000, + .regshift = 0, + .flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ, + }, { + /* end marker */ + }, +}; + +static struct platform_device board_a9m9750dev_serial_device = { + .name = "serial8250", + .dev = { + .platform_data = board_a9m9750dev_serial8250_port, + }, +}; + +static struct platform_device *board_a9m9750dev_devices[] __initdata = { + &board_a9m9750dev_serial_device, +}; + +void __init board_a9m9750dev_init_machine(void) +{ + u32 reg; + + /* setup static CS0: memory base ... */ + REGSETIM(SYS_SMCSSMB(0), SYS_SMCSSMB, CSxB, + NS9XXX_CSxSTAT_PHYS(0) >> 12); + + /* ... and mask */ + reg = SYS_SMCSSMM(0); + REGSETIM(reg, SYS_SMCSSMM, CSxM, 0xfffff); + REGSET(reg, SYS_SMCSSMM, CSEx, EN); + SYS_SMCSSMM(0) = reg; + + /* setup static CS0: memory configuration */ + reg = MEM_SMC(0); + REGSET(reg, MEM_SMC, WSMC, OFF); + REGSET(reg, MEM_SMC, BSMC, OFF); + REGSET(reg, MEM_SMC, EW, OFF); + REGSET(reg, MEM_SMC, PB, 1); + REGSET(reg, MEM_SMC, PC, AL); + REGSET(reg, MEM_SMC, PM, DIS); + REGSET(reg, MEM_SMC, MW, 8); + MEM_SMC(0) = reg; + + /* setup static CS0: timing */ + MEM_SMWED(0) = 0x2; + MEM_SMOED(0) = 0x2; + MEM_SMRD(0) = 0x6; + MEM_SMWD(0) = 0x6; + + platform_add_devices(board_a9m9750dev_devices, + ARRAY_SIZE(board_a9m9750dev_devices)); +} + diff --git a/arch/arm/mach-ns9xxx/board-a9m9750dev.h b/arch/arm/mach-ns9xxx/board-a9m9750dev.h new file mode 100644 index 000000000000..edc75abbc5dd --- /dev/null +++ b/arch/arm/mach-ns9xxx/board-a9m9750dev.h @@ -0,0 +1,15 @@ +/* + * arch/arm/mach-ns9xxx/board-a9m9750dev.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include + +void __init board_a9m9750dev_map_io(void); +void __init board_a9m9750dev_init_machine(void); +void __init board_a9m9750dev_init_irq(void); diff --git a/arch/arm/mach-ns9xxx/generic.c b/arch/arm/mach-ns9xxx/generic.c new file mode 100644 index 000000000000..83e2b6532b22 --- /dev/null +++ b/arch/arm/mach-ns9xxx/generic.c @@ -0,0 +1,42 @@ +/* + * arch/arm/mach-ns9xxx/generic.c + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +static struct map_desc standard_io_desc[] __initdata = { + { /* BBus */ + .virtual = io_p2v(0x90000000), + .pfn = __phys_to_pfn(0x90000000), + .length = 0x00700000, + .type = MT_DEVICE, + }, { /* AHB */ + .virtual = io_p2v(0xa0100000), + .pfn = __phys_to_pfn(0xa0100000), + .length = 0x00900000, + .type = MT_DEVICE, + }, +}; + +void __init ns9xxx_map_io(void) +{ + iotable_init(standard_io_desc, ARRAY_SIZE(standard_io_desc)); +} + +void __init ns9xxx_init_machine(void) +{ +} diff --git a/arch/arm/mach-ns9xxx/generic.h b/arch/arm/mach-ns9xxx/generic.h new file mode 100644 index 000000000000..687e291773f4 --- /dev/null +++ b/arch/arm/mach-ns9xxx/generic.h @@ -0,0 +1,19 @@ +/* + * arch/arm/mach-ns9xxx/generic.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include +#include + +void __init ns9xxx_init_irq(void); +void __init ns9xxx_map_io(void); +void __init ns9xxx_init_machine(void); + +extern struct sys_timer ns9xxx_timer; diff --git a/arch/arm/mach-ns9xxx/irq.c b/arch/arm/mach-ns9xxx/irq.c new file mode 100644 index 000000000000..83d92724a971 --- /dev/null +++ b/arch/arm/mach-ns9xxx/irq.c @@ -0,0 +1,94 @@ +/* + * arch/arm/mach-ns9xxx/irq.c + * + * Copyright (C) 2006,2007 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include + +#include "generic.h" + +static void ns9xxx_ack_irq_timer(unsigned int irq) +{ + u32 tc = SYS_TC(irq - IRQ_TIMER0); + + REGSET(tc, SYS_TCx, INTC, SET); + SYS_TC(irq - IRQ_TIMER0) = tc; + + REGSET(tc, SYS_TCx, INTC, UNSET); + SYS_TC(irq - IRQ_TIMER0) = tc; +} + +void (*ns9xxx_ack_irq_functions[NR_IRQS])(unsigned int) = { + [IRQ_TIMER0] = ns9xxx_ack_irq_timer, + [IRQ_TIMER1] = ns9xxx_ack_irq_timer, + [IRQ_TIMER2] = ns9xxx_ack_irq_timer, + [IRQ_TIMER3] = ns9xxx_ack_irq_timer, +}; + +static void ns9xxx_mask_irq(unsigned int irq) +{ + /* XXX: better use cpp symbols */ + SYS_IC(irq / 4) &= ~(1 << (7 + 8 * (3 - (irq & 3)))); +} + +static void ns9xxx_ack_irq(unsigned int irq) +{ + if (!ns9xxx_ack_irq_functions[irq]) { + printk(KERN_ERR "no ack function for irq %u\n", irq); + BUG(); + } + + ns9xxx_ack_irq_functions[irq](irq); + SYS_ISRADDR = 0; +} + +static void ns9xxx_maskack_irq(unsigned int irq) +{ + ns9xxx_mask_irq(irq); + ns9xxx_ack_irq(irq); +} + +static void ns9xxx_unmask_irq(unsigned int irq) +{ + /* XXX: better use cpp symbols */ + SYS_IC(irq / 4) |= 1 << (7 + 8 * (3 - (irq & 3))); +} + +static struct irq_chip ns9xxx_chip = { + .ack = ns9xxx_ack_irq, + .mask = ns9xxx_mask_irq, + .mask_ack = ns9xxx_maskack_irq, + .unmask = ns9xxx_unmask_irq, +}; + +void __init ns9xxx_init_irq(void) +{ + int i; + + /* disable all IRQs */ + for (i = 0; i < 8; ++i) + SYS_IC(i) = (4 * i) << 24 | (4 * i + 1) << 16 | + (4 * i + 2) << 8 | (4 * i + 3); + + /* simple interrupt prio table: + * prio(x) < prio(y) <=> x < y + */ + for (i = 0; i < 32; ++i) + SYS_IVA(i) = i; + + for (i = IRQ_WATCHDOG; i <= IRQ_EXT3; ++i) { + set_irq_chip(i, &ns9xxx_chip); + set_irq_handler(i, handle_level_irq); + set_irq_flags(i, IRQF_VALID); + } +} diff --git a/arch/arm/mach-ns9xxx/mach-cc9p9360dev.c b/arch/arm/mach-ns9xxx/mach-cc9p9360dev.c new file mode 100644 index 000000000000..a193dd931512 --- /dev/null +++ b/arch/arm/mach-ns9xxx/mach-cc9p9360dev.c @@ -0,0 +1,41 @@ +/* + * arch/arm/mach-ns9xxx/mach-cc9p9360dev.c + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include + +#include "board-a9m9750dev.h" +#include "generic.h" + +static void __init mach_cc9p9360dev_map_io(void) +{ + ns9xxx_map_io(); + board_a9m9750dev_map_io(); +} + +static void __init mach_cc9p9360dev_init_irq(void) +{ + ns9xxx_init_irq(); + board_a9m9750dev_init_irq(); +} + +static void __init mach_cc9p9360dev_init_machine(void) +{ + ns9xxx_init_machine(); + board_a9m9750dev_init_machine(); +} + +MACHINE_START(CC9P9360DEV, "Connect Core 9P 9360 on an A9M9750 Devboard") + .map_io = mach_cc9p9360dev_map_io, + .init_irq = mach_cc9p9360dev_init_irq, + .init_machine = mach_cc9p9360dev_init_machine, + .timer = &ns9xxx_timer, + .boot_params = 0x100, +MACHINE_END diff --git a/arch/arm/mach-ns9xxx/time.c b/arch/arm/mach-ns9xxx/time.c new file mode 100644 index 000000000000..eec05f18714a --- /dev/null +++ b/arch/arm/mach-ns9xxx/time.c @@ -0,0 +1,88 @@ +/* + * arch/arm/mach-ns9xxx/time.c + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include "generic.h" + +#define TIMERCLOCKSELECT 64 + +static u32 usecs_per_tick; + +static irqreturn_t +ns9xxx_timer_interrupt(int irq, void *dev_id) +{ + write_seqlock(&xtime_lock); + timer_tick(); + write_sequnlock(&xtime_lock); + + return IRQ_HANDLED; +} + +static unsigned long ns9xxx_timer_gettimeoffset(void) +{ + /* return the microseconds which have passed since the last interrupt + * was _serviced_. That is, if an interrupt is pending or the counter + * reloads, return one periode more. */ + + u32 counter1 = SYS_TR(0); + int pending = SYS_ISR & (1 << IRQ_TIMER0); + u32 counter2 = SYS_TR(0); + u32 elapsed; + + if (pending || counter2 > counter1) + elapsed = 2 * SYS_TRC(0) - counter2; + else + elapsed = SYS_TRC(0) - counter1; + + return (elapsed * usecs_per_tick) >> 16; + +} + +static struct irqaction ns9xxx_timer_irq = { + .name = "NS9xxx Timer Tick", + .flags = IRQF_DISABLED | IRQF_TIMER, + .handler = ns9xxx_timer_interrupt, +}; + +static void __init ns9xxx_timer_init(void) +{ + int tc; + + usecs_per_tick = + SH_DIV(1000000 * TIMERCLOCKSELECT, ns9xxx_cpuclock(), 16); + + /* disable timer */ + if ((tc = SYS_TC(0)) & SYS_TCx_TEN) + SYS_TC(0) = tc & ~SYS_TCx_TEN; + + SYS_TRC(0) = SH_DIV(ns9xxx_cpuclock(), (TIMERCLOCKSELECT * HZ), 0); + + REGSET(tc, SYS_TCx, TEN, EN); + REGSET(tc, SYS_TCx, TLCS, DIV64); /* This must match TIMERCLOCKSELECT */ + REGSET(tc, SYS_TCx, INTS, EN); + REGSET(tc, SYS_TCx, UDS, DOWN); + REGSET(tc, SYS_TCx, TDBG, STOP); + REGSET(tc, SYS_TCx, TSZ, 32); + REGSET(tc, SYS_TCx, REN, EN); + SYS_TC(0) = tc; + + setup_irq(IRQ_TIMER0, &ns9xxx_timer_irq); +} + +struct sys_timer ns9xxx_timer = { + .init = ns9xxx_timer_init, + .offset = ns9xxx_timer_gettimeoffset, +}; diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index aade2f72c920..27624447ec7d 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -171,8 +171,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_NS9XXX + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_NS9XXX select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_CACHE_VIVT diff --git a/include/asm-arm/arch-ns9xxx/board.h b/include/asm-arm/arch-ns9xxx/board.h new file mode 100644 index 000000000000..91dc8fb1027f --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/board.h @@ -0,0 +1,18 @@ +/* + * include/asm-arm/arch-ns9xxx/board.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_BOARD_H +#define __ASM_ARCH_BOARD_H + +#include + +#define board_is_a9m9750dev() (machine_is_cc9p9360dev()) + +#endif /* ifndef __ASM_ARCH_BOARD_H */ diff --git a/include/asm-arm/arch-ns9xxx/clock.h b/include/asm-arm/arch-ns9xxx/clock.h new file mode 100644 index 000000000000..4371a485db47 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/clock.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-ns9xxx/clock.h + * + * Copyright (C) 2007 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_CLOCK_H +#define __ASM_ARCH_CLOCK_H + +static inline u32 ns9xxx_systemclock(void) +{ + /* + * This should be a multiple of HZ * TIMERCLOCKSELECT (in time.c) + */ + return 353894400; +} + +static inline const u32 ns9xxx_cpuclock(void) +{ + return ns9xxx_systemclock() / 2; +} + +static inline const u32 ns9xxx_ahbclock(void) +{ + return ns9xxx_systemclock() / 4; +} + +static inline const u32 ns9xxx_bbusclock(void) +{ + return ns9xxx_systemclock() / 8; +} + +#endif /* ifndef __ASM_ARCH_CLOCK_H */ diff --git a/include/asm-arm/arch-ns9xxx/debug-macro.S b/include/asm-arm/arch-ns9xxx/debug-macro.S new file mode 100644 index 000000000000..b21b93eb2dbc --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/debug-macro.S @@ -0,0 +1,22 @@ +/* + * include/asm-arm/arch-ns9xxx/debug-macro.S + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include + +#include + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 + ldreq \rx, =NS9XXX_CSxSTAT_PHYS(0) + ldrne \rx, =io_p2v(NS9XXX_CSxSTAT_PHYS(0)) + .endm + +#define UART_SHIFT 2 +#include diff --git a/include/asm-arm/arch-ns9xxx/dma.h b/include/asm-arm/arch-ns9xxx/dma.h new file mode 100644 index 000000000000..a67cbbe009c4 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/dma.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-ns9xxx/dma.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_DMA_H +#define __ASM_ARCH_DMA_H + +#endif /* ifndef __ASM_ARCH_DMA_H */ diff --git a/include/asm-arm/arch-ns9xxx/entry-macro.S b/include/asm-arm/arch-ns9xxx/entry-macro.S new file mode 100644 index 000000000000..467a1986d259 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/entry-macro.S @@ -0,0 +1,22 @@ +/* + * include/asm-arm/arch-ns9xxx/entry-macro.S + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + ldr \base, =SYS_ISRADDR + ldr \irqstat, [\base, #(SYS_ISA - SYS_ISRADDR)] + cmp \irqstat, #0 + ldrne \irqnr, [\base] + .endm + + .macro disable_fiq + .endm diff --git a/include/asm-arm/arch-ns9xxx/hardware.h b/include/asm-arm/arch-ns9xxx/hardware.h new file mode 100644 index 000000000000..6819da7c48d4 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/hardware.h @@ -0,0 +1,67 @@ +/* + * include/asm-arm/arch-ns9xxx/hardware.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include + +/* + * NetSilicon NS9xxx internal mapping: + * + * physical <--> virtual + * 0x90000000 - 0x906fffff <--> 0xf9000000 - 0xf96fffff + * 0xa0100000 - 0xa0afffff <--> 0xfa100000 - 0xfaafffff + */ +#define io_p2v(x) (0xf0000000 \ + + (((x) & 0xf0000000) >> 4) \ + + ((x) & 0x00ffffff)) + +#define io_v2p(x) ((((x) & 0x0f000000) << 4) \ + + ((x) & 0x00ffffff)) + +#define __REGBIT(bit) ((u32)1 << (bit)) +#define __REGBITS(hbit, lbit) ((((u32)1 << ((hbit) - (lbit) + 1)) - 1) << (lbit)) +#define __REGVAL(mask, value) (((value) * ((mask) & (-(mask))) & (mask))) + +#ifndef __ASSEMBLY__ + +# define __REG(x) (*((volatile u32 *)io_p2v((x)))) +# define __REG2(x, y) (*((volatile u32 *)io_p2v((x)) + (y))) + +# define __REGB(x) (*((volatile u8 *)io_p2v((x)))) +# define __REGB2(x) (*((volatile u8 *)io_p2v((x)) + (y))) + +# define REGSET(var, reg, field, value) \ + ((var) = (((var) \ + & ~(reg ## _ ## field & \ + ~ reg ## _ ## field ## _ ## value)) \ + | (reg ## _ ## field ## _ ## value))) + +# define REGSETIM(var, reg, field, value) \ + ((var) = (((var) \ + & ~(reg ## _ ## field & \ + ~(__REGVAL(reg ## _ ## field, value)))) \ + | (__REGVAL(reg ## _ ## field, value)))) + +# define REGGET(reg, field) \ + ((reg & (reg ## _ ## field)) / (field & (-field))) + +#else + +# define __REG(x) io_p2v(x) +# define __REG2(x, y) io_p2v((x) + (y)) + +# define __REGB(x) __REG((x)) +# define __REGB2(x, y) __REG2((x), (y)) + +#endif + +#endif /* ifndef __ASM_ARCH_HARDWARE_H */ diff --git a/include/asm-arm/arch-ns9xxx/io.h b/include/asm-arm/arch-ns9xxx/io.h new file mode 100644 index 000000000000..6f82d28af120 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/io.h @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-ns9xxx/io.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#define IO_SPACE_LIMIT 0xffffffff /* XXX */ + +#define __io(a) ((void __iomem *)(a)) +#define __mem_pci(a) (a) +#define __mem_isa(a) (IO_BASE + (a)) + +#endif /* ifndef __ASM_ARCH_IO_H */ diff --git a/include/asm-arm/arch-ns9xxx/irqs.h b/include/asm-arm/arch-ns9xxx/irqs.h new file mode 100644 index 000000000000..25d8d28b27f3 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/irqs.h @@ -0,0 +1,85 @@ +/* + * include/asm-arm/arch-ns9xxx/irqs.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#define IRQ_WATCHDOG 0 +#define IRQ_AHBBUSERR 1 +#define IRQ_BBUSAGG 2 +/* irq 3 is reserved for NS9360 */ +#define IRQ_ETHRX 4 +#define IRQ_ETHTX 5 +#define IRQ_ETHPHY 6 +#define IRQ_LCD 7 +#define IRQ_SERBRX 8 +#define IRQ_SERBTX 9 +#define IRQ_SERARX 10 +#define IRQ_SERATX 11 +#define IRQ_SERCRX 12 +#define IRQ_SERCTX 13 +#define IRQ_I2C 14 +#define IRQ_BBUSDMA 15 +#define IRQ_TIMER0 16 +#define IRQ_TIMER1 17 +#define IRQ_TIMER2 18 +#define IRQ_TIMER3 19 +#define IRQ_TIMER4 20 +#define IRQ_TIMER5 21 +#define IRQ_TIMER6 22 +#define IRQ_TIMER7 23 +#define IRQ_RTC 24 +#define IRQ_USBHOST 25 +#define IRQ_USBDEVICE 26 +#define IRQ_IEEE1284 27 +#define IRQ_EXT0 28 +#define IRQ_EXT1 29 +#define IRQ_EXT2 30 +#define IRQ_EXT3 31 + +#define BBUS_IRQ(irq) (32 + irq) + +#define IRQ_BBUS_DMA BBUS_IRQ(0) +#define IRQ_BBUS_SERBRX BBUS_IRQ(2) +#define IRQ_BBUS_SERBTX BBUS_IRQ(3) +#define IRQ_BBUS_SERARX BBUS_IRQ(4) +#define IRQ_BBUS_SERATX BBUS_IRQ(5) +#define IRQ_BBUS_SERCRX BBUS_IRQ(6) +#define IRQ_BBUS_SERCTX BBUS_IRQ(7) +#define IRQ_BBUS_SERDRX BBUS_IRQ(8) +#define IRQ_BBUS_SERDTX BBUS_IRQ(9) +#define IRQ_BBUS_I2C BBUS_IRQ(10) +#define IRQ_BBUS_1284 BBUS_IRQ(11) +#define IRQ_BBUS_UTIL BBUS_IRQ(12) +#define IRQ_BBUS_RTC BBUS_IRQ(13) +#define IRQ_BBUS_USBHST BBUS_IRQ(14) +#define IRQ_BBUS_USBDEV BBUS_IRQ(15) +#define IRQ_BBUS_AHBDMA1 BBUS_IRQ(24) +#define IRQ_BBUS_AHBDMA2 BBUS_IRQ(25) + +/* + * these Interrupts are specific for the a9m9750dev board. + * They are generated by an FPGA that interrupts the CPU on + * IRQ_EXT2 + */ +#define FPGA_IRQ(irq) (64 + irq) + +#define IRQ_FPGA_UARTA FPGA_IRQ(0) +#define IRQ_FPGA_UARTB FPGA_IRQ(1) +#define IRQ_FPGA_UARTC FPGA_IRQ(2) +#define IRQ_FPGA_UARTD FPGA_IRQ(3) +#define IRQ_FPGA_TOUCH FPGA_IRQ(4) +#define IRQ_FPGA_CF FPGA_IRQ(5) +#define IRQ_FPGA_CAN0 FPGA_IRQ(6) +#define IRQ_FPGA_CAN1 FPGA_IRQ(7) + +#define NR_IRQS 72 + +#endif /* __ASM_ARCH_IRQS_H */ diff --git a/include/asm-arm/arch-ns9xxx/memory.h b/include/asm-arm/arch-ns9xxx/memory.h new file mode 100644 index 000000000000..ce1343e593e1 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/memory.h @@ -0,0 +1,27 @@ +/* + * include/asm-arm/arch-ns9xxx/memory.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. +*/ +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +/* x in [0..3] */ +#define NS9XXX_CSxSTAT_PHYS(x) UL(((x) + 4) << 28) + +#define NS9XXX_CS0STAT_LENGTH UL(0x1000) +#define NS9XXX_CS1STAT_LENGTH UL(0x1000) +#define NS9XXX_CS2STAT_LENGTH UL(0x1000) +#define NS9XXX_CS3STAT_LENGTH UL(0x1000) + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + +#endif diff --git a/include/asm-arm/arch-ns9xxx/processor.h b/include/asm-arm/arch-ns9xxx/processor.h new file mode 100644 index 000000000000..716c106ac0bf --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/processor.h @@ -0,0 +1,18 @@ +/* + * include/asm-arm/arch-ns9xxx/processor.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_PROCESSOR_H +#define __ASM_ARCH_PROCESSOR_H + +#include + +#define processor_is_ns9360() (machine_is_cc9p9360dev()) + +#endif /* ifndef __ASM_ARCH_PROCESSOR_H */ diff --git a/include/asm-arm/arch-ns9xxx/regs-bbu.h b/include/asm-arm/arch-ns9xxx/regs-bbu.h new file mode 100644 index 000000000000..e26269546240 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/regs-bbu.h @@ -0,0 +1,21 @@ +/* + * include/asm-arm/arch-ns9xxx/regs-bbu.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_REGSBBU_H +#define __ASM_ARCH_REGSBBU_H + +#include + +/* BBus Utility */ + +/* GPIO Configuration Register */ +#define BBU_GC(x) __REG2(0x9060000c, (x)) + +#endif /* ifndef __ASM_ARCH_REGSBBU_H */ diff --git a/include/asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h b/include/asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h new file mode 100644 index 000000000000..c3dc532dd20c --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h @@ -0,0 +1,24 @@ +/* + * include/asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_REGSBOARDA9M9750_H +#define __ASM_ARCH_REGSBOARDA9M9750_H + +#include + +#define FPGA_UARTA_BASE io_p2v(NS9XXX_CSxSTAT_PHYS(0)) +#define FPGA_UARTB_BASE io_p2v(NS9XXX_CSxSTAT_PHYS(0) + 0x08) +#define FPGA_UARTC_BASE io_p2v(NS9XXX_CSxSTAT_PHYS(0) + 0x10) +#define FPGA_UARTD_BASE io_p2v(NS9XXX_CSxSTAT_PHYS(0) + 0x18) + +#define FPGA_IER __REGB(NS9XXX_CSxSTAT_PHYS(0) + 0x50) +#define FPGA_ISR __REGB(NS9XXX_CSxSTAT_PHYS(0) + 0x60) + +#endif /* ifndef __ASM_ARCH_REGSBOARDA9M9750_H */ diff --git a/include/asm-arm/arch-ns9xxx/regs-mem.h b/include/asm-arm/arch-ns9xxx/regs-mem.h new file mode 100644 index 000000000000..8ed8448767b9 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/regs-mem.h @@ -0,0 +1,135 @@ +/* + * include/asm-arm/arch-ns9xxx/regs-mem.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_REGSMEM_H +#define __ASM_ARCH_REGSMEM_H + +#include + +/* Memory Module */ + +/* Control register */ +#define MEM_CTRL __REG(0xa0700000) + +/* Status register */ +#define MEM_STAT __REG(0xa0700004) + +/* Configuration register */ +#define MEM_CONF __REG(0xa0700008) + +/* Dynamic Memory Control register */ +#define MEM_DMCTRL __REG(0xa0700020) + +/* Dynamic Memory Refresh Timer */ +#define MEM_DMRT __REG(0xa0700024) + +/* Dynamic Memory Read Configuration register */ +#define MEM_DMRC __REG(0xa0700028) + +/* Dynamic Memory Precharge Command Period (tRP) */ +#define MEM_DMPCP __REG(0xa0700030) + +/* Dynamic Memory Active to Precharge Command Period (tRAS) */ +#define MEM_DMAPCP __REG(0xa0700034) + +/* Dynamic Memory Self-Refresh Exit Time (tSREX) */ +#define MEM_DMSRET __REG(0xa0700038) + +/* Dynamic Memory Last Data Out to Active Time (tAPR) */ +#define MEM_DMLDOAT __REG(0xa070003c) + +/* Dynamic Memory Data-in to Active Command Time (tDAL or TAPW) */ +#define MEM_DMDIACT __REG(0xa0700040) + +/* Dynamic Memory Write Recovery Time (tWR, tDPL, tRWL, tRDL) */ +#define MEM_DMWRT __REG(0xa0700044) + +/* Dynamic Memory Active to Active Command Period (tRC) */ +#define MEM_DMAACP __REG(0xa0700048) + +/* Dynamic Memory Auto Refresh Period, and Auto Refresh to Active Command Period (tRFC) */ +#define MEM_DMARP __REG(0xa070004c) + +/* Dynamic Memory Exit Self-Refresh to Active Command (tXSR) */ +#define MEM_DMESRAC __REG(0xa0700050) + +/* Dynamic Memory Active Bank A to Active B Time (tRRD) */ +#define MEM_DMABAABT __REG(0xa0700054) + +/* Dynamic Memory Load Mode register to Active Command Time (tMRD) */ +#define MEM_DMLMACT __REG(0xa0700058) + +/* Static Memory Extended Wait */ +#define MEM_SMEW __REG(0xa0700080) + +/* Dynamic Memory Configuration Register x */ +#define MEM_DMCONF(x) __REG2(0xa0700100, (x) << 3) + +/* Dynamic Memory RAS and CAS Delay x */ +#define MEM_DMRCD(x) __REG2(0xa0700104, (x) << 3) + +/* Static Memory Configuration Register x */ +#define MEM_SMC(x) __REG2(0xa0700200, (x) << 3) + +/* Static Memory Configuration Register x: Write protect */ +#define MEM_SMC_WSMC __REGBIT(20) +#define MEM_SMC_WSMC_OFF __REGVAL(MEM_SMC_WSMC, 0) +#define MEM_SMC_WSMC_ON __REGVAL(MEM_SMC_WSMC, 1) + +/* Static Memory Configuration Register x: Buffer enable */ +#define MEM_SMC_BSMC __REGBIT(19) +#define MEM_SMC_BSMC_OFF __REGVAL(MEM_SMC_BSMC, 0) +#define MEM_SMC_BSMC_ON __REGVAL(MEM_SMC_BSMC, 1) + +/* Static Memory Configuration Register x: Extended Wait */ +#define MEM_SMC_EW __REGBIT(8) +#define MEM_SMC_EW_OFF __REGVAL(MEM_SMC_EW, 0) +#define MEM_SMC_EW_ON __REGVAL(MEM_SMC_EW, 1) + +/* Static Memory Configuration Register x: Byte lane state */ +#define MEM_SMC_PB __REGBIT(7) +#define MEM_SMC_PB_0 __REGVAL(MEM_SMC_PB, 0) +#define MEM_SMC_PB_1 __REGVAL(MEM_SMC_PB, 1) + +/* Static Memory Configuration Register x: Chip select polarity */ +#define MEM_SMC_PC __REGBIT(6) +#define MEM_SMC_PC_AL __REGVAL(MEM_SMC_PC, 0) +#define MEM_SMC_PC_AH __REGVAL(MEM_SMC_PC, 1) + +/* static memory configuration register x: page mode*/ +#define MEM_SMC_PM __REGBIT(3) +#define MEM_SMC_PM_DIS __REGVAL(MEM_SMC_PM, 0) +#define MEM_SMC_PM_ASYNC __REGVAL(MEM_SMC_PM, 1) + +/* static memory configuration register x: Memory width */ +#define MEM_SMC_MW __REGBITS(1, 0) +#define MEM_SMC_MW_8 __REGVAL(MEM_SMC_MW, 0) +#define MEM_SMC_MW_16 __REGVAL(MEM_SMC_MW, 1) +#define MEM_SMC_MW_32 __REGVAL(MEM_SMC_MW, 2) + +/* Static Memory Write Enable Delay x */ +#define MEM_SMWED(x) __REG2(0xa0700204, (x) << 3) + +/* Static Memory Output Enable Delay x */ +#define MEM_SMOED(x) __REG2(0xa0700208, (x) << 3) + +/* Static Memory Read Delay x */ +#define MEM_SMRD(x) __REG2(0xa070020c, (x) << 3) + +/* Static Memory Page Mode Read Delay 0 */ +#define MEM_SMPMRD(x) __REG2(0xa0700210, (x) << 3) + +/* Static Memory Write Delay */ +#define MEM_SMWD(x) __REG2(0xa0700214, (x) << 3) + +/* Static Memory Turn Round Delay x */ +#define MEM_SWT(x) __REG2(0xa0700218, (x) << 3) + +#endif /* ifndef __ASM_ARCH_REGSMEM_H */ diff --git a/include/asm-arm/arch-ns9xxx/regs-sys.h b/include/asm-arm/arch-ns9xxx/regs-sys.h new file mode 100644 index 000000000000..8162a50bb273 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/regs-sys.h @@ -0,0 +1,157 @@ +/* + * include/asm-arm/arch-ns9xxx/regs-sys.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_REGSSYS_H +#define __ASM_ARCH_REGSSYS_H + +#include + +/* System Control Module */ + +/* AHB Arbiter Gen Configuration */ +#define SYS_AHBAGENCONF __REG(0xa0900000) + +/* BRC */ +#define SYS_BRC(x) __REG2(0xa0900004, (x)) + +/* Timer x Reload Count register */ +#define SYS_TRC(x) __REG2(0xa0900044, (x)) + +/* Timer x Read register */ +#define SYS_TR(x) __REG2(0xa0900084, (x)) + +/* Interrupt Vector Address Register Level x */ +#define SYS_IVA(x) __REG2(0xa09000c4, (x)) + +/* Interrupt Configuration registers */ +#define SYS_IC(x) __REG2(0xa0900144, (x)) + +/* ISRADDR */ +#define SYS_ISRADDR __REG(0xa0900164) + +/* Interrupt Status Active */ +#define SYS_ISA __REG(0xa0900168) + +/* Interrupt Status Raw */ +#define SYS_ISR __REG(0xa090016c) + +/* Timer Interrupt Status register */ +#define SYS_TIS __REG(0xa0900170) + +/* PLL Configuration register */ +#define SYS_PLL __REG(0xa0900188) + +/* PLL Configuration register: PLL SW change */ +#define SYS_PLL_SWC __REGBIT(15) +#define SYS_PLL_SWC_NO __REGVAL(SYS_PLL_SWC, 0) +#define SYS_PLL_SWC_YES __REGVAL(SYS_PLL_SWC, 1) + +/* Timer x Control register */ +#define SYS_TC(x) __REG2(0xa0900190, (x)) + +/* Timer x Control register: Timer enable */ +#define SYS_TCx_TEN __REGBIT(15) +#define SYS_TCx_TEN_DIS __REGVAL(SYS_TCx_TEN, 1) +#define SYS_TCx_TEN_EN __REGVAL(SYS_TCx_TEN, 1) + +/* Timer x Control register: CPU debug mode */ +#define SYS_TCx_TDBG __REGBIT(10) +#define SYS_TCx_TDBG_CONT __REGVAL(SYS_TCx_TDBG, 0) +#define SYS_TCx_TDBG_STOP __REGVAL(SYS_TCx_TDBG, 1) + +/* Timer x Control register: Interrupt clear */ +#define SYS_TCx_INTC __REGBIT(9) +#define SYS_TCx_INTC_UNSET __REGVAL(SYS_TCx_INTC, 0) +#define SYS_TCx_INTC_SET __REGVAL(SYS_TCx_INTC, 1) + +/* Timer x Control register: Timer clock select */ +#define SYS_TCx_TLCS __REGBITS(8, 6) +#define SYS_TCx_TLCS_CPU __REGVAL(SYS_TCx_TLCS, 0) /* CPU clock */ +#define SYS_TCx_TLCS_DIV2 __REGVAL(SYS_TCx_TLCS, 1) /* CPU clock / 2 */ +#define SYS_TCx_TLCS_DIV4 __REGVAL(SYS_TCx_TLCS, 2) /* CPU clock / 4 */ +#define SYS_TCx_TLCS_DIV8 __REGVAL(SYS_TCx_TLCS, 3) /* CPU clock / 8 */ +#define SYS_TCx_TLCS_DIV16 __REGVAL(SYS_TCx_TLCS, 4) /* CPU clock / 16 */ +#define SYS_TCx_TLCS_DIV32 __REGVAL(SYS_TCx_TLCS, 5) /* CPU clock / 32 */ +#define SYS_TCx_TLCS_DIV64 __REGVAL(SYS_TCx_TLCS, 6) /* CPU clock / 64 */ +#define SYS_TCx_TLCS_EXT __REGVAL(SYS_TCx_TLCS, 7) + +/* Timer x Control register: Timer mode */ +#define SYS_TCx_TM __REGBITS(5, 4) +#define SYS_TCx_TM_IEE __REGVAL(SYS_TCx_TM, 0) /* Internal timer or external event */ +#define SYS_TCx_TM_ELL __REGVAL(SYS_TCx_TM, 1) /* External low-level, gated timer */ +#define SYS_TCx_TM_EHL __REGVAL(SYS_TCx_TM, 2) /* External high-level, gated timer */ +#define SYS_TCx_TM_CONCAT __REGVAL(SYS_TCx_TM, 3) /* Concatenate the lower timer. */ + +/* Timer x Control register: Interrupt select */ +#define SYS_TCx_INTS __REGBIT(3) +#define SYS_TCx_INTS_DIS __REGVAL(SYS_TCx_INTS, 0) +#define SYS_TCx_INTS_EN __REGVAL(SYS_TCx_INTS, 1) + +/* Timer x Control register: Up/down select */ +#define SYS_TCx_UDS __REGBIT(2) +#define SYS_TCx_UDS_UP __REGVAL(SYS_TCx_UDS, 0) +#define SYS_TCx_UDS_DOWN __REGVAL(SYS_TCx_UDS, 1) + +/* Timer x Control register: 32- or 16-bit timer */ +#define SYS_TCx_TSZ __REGBIT(1) +#define SYS_TCx_TSZ_16 __REGVAL(SYS_TCx_TSZ, 0) +#define SYS_TCx_TSZ_32 __REGVAL(SYS_TCx_TSZ, 1) + +/* Timer x Control register: Reload enable */ +#define SYS_TCx_REN __REGBIT(0) +#define SYS_TCx_REN_DIS __REGVAL(SYS_TCx_REN, 0) +#define SYS_TCx_REN_EN __REGVAL(SYS_TCx_REN, 1) + +/* System Memory Chip Select x Dynamic Memory Base */ +#define SYS_SMCSDMB(x) __REG2(0xa09001d0, (x) << 1) + +/* System Memory Chip Select x Dynamic Memory Mask */ +#define SYS_SMCSDMM(x) __REG2(0xa09001d4, (x) << 1) + +/* System Memory Chip Select x Static Memory Base */ +#define SYS_SMCSSMB(x) __REG2(0xa09001f0, (x) << 1) + +/* System Memory Chip Select x Static Memory Base: Chip select x base */ +#define SYS_SMCSSMB_CSxB __REGBITS(31, 12) + +/* System Memory Chip Select x Static Memory Mask */ +#define SYS_SMCSSMM(x) __REG2(0xa09001f4, (x) << 1) + +/* System Memory Chip Select x Static Memory Mask: Chip select x mask */ +#define SYS_SMCSSMM_CSxM __REGBITS(31, 12) + +/* System Memory Chip Select x Static Memory Mask: Chip select x enable */ +#define SYS_SMCSSMM_CSEx __REGBIT(0) +#define SYS_SMCSSMM_CSEx_DIS __REGVAL(SYS_SMCSSMM_CSEx, 0) +#define SYS_SMCSSMM_CSEx_EN __REGVAL(SYS_SMCSSMM_CSEx, 1) + +/* General purpose, user-defined ID register */ +#define SYS_GENID __REG(0xa0900210) + +/* External Interrupt x Control register */ +#define SYS_EIC(x) __REG2(0xa0900214, (x)) + +/* External Interrupt x Control register: Status */ +#define SYS_EIC_STS __REGBIT(3) + +/* External Interrupt x Control register: Clear */ +#define SYS_EIC_CLR __REGBIT(2) + +/* External Interrupt x Control register: Polarity */ +#define SYS_EIC_PLTY __REGBIT(1) +#define SYS_EIC_PLTY_AH __REGVAL(SYS_EIC_PLTY, 0) +#define SYS_EIC_PLTY_AL __REGVAL(SYS_EIC_PLTY, 1) + +/* External Interrupt x Control register: Level edge */ +#define SYS_EIC_LVEDG __REGBIT(0) +#define SYS_EIC_LVEDG_LEVEL __REGVAL(SYS_EIC_LVEDG, 0) +#define SYS_EIC_LVEDG_EDGE __REGVAL(SYS_EIC_LVEDG, 1) + +#endif /* ifndef __ASM_ARCH_REGSSYS_H */ diff --git a/include/asm-arm/arch-ns9xxx/system.h b/include/asm-arm/arch-ns9xxx/system.h new file mode 100644 index 000000000000..e3cd4d31b3f3 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/system.h @@ -0,0 +1,34 @@ +/* + * include/asm-arm/arch-ns9xxx/system.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include +#include +#include + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + u32 reg; + + reg = SYS_PLL >> 16; + REGSET(reg, SYS_PLL, SWC, YES); + SYS_PLL = reg; + + BUG(); +} + +#endif /* ifndef __ASM_ARCH_SYSTEM_H */ diff --git a/include/asm-arm/arch-ns9xxx/timex.h b/include/asm-arm/arch-ns9xxx/timex.h new file mode 100644 index 000000000000..f776cbd2622d --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/timex.h @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-ns9xxx/timex.h + * + * Copyright (C) 2005-2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_TIMEX_H +#define __ASM_ARCH_TIMEX_H + +/* + * value for CLOCK_TICK_RATE stolen from include/asm-arm/arch-s3c2410/timex.h. + * See there for an explanation. + */ +#define CLOCK_TICK_RATE 12000000 + +#endif /* ifndef __ASM_ARCH_TIMEX_H */ diff --git a/include/asm-arm/arch-ns9xxx/uncompress.h b/include/asm-arm/arch-ns9xxx/uncompress.h new file mode 100644 index 000000000000..961ca7dc9954 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/uncompress.h @@ -0,0 +1,35 @@ +/* + * include/asm-arm/arch-ns9xxx/uncompress.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_UNCOMPRESS_H +#define __ASM_ARCH_UNCOMPRESS_H + +static void putc(char c) +{ + volatile u8 *base = (volatile u8 *)0x40000000; + int t = 0x10000; + + do { + if (base[5] & 0x20) { + base[0] = c; + break; + } + } while (--t); +} + +#define arch_decomp_setup() +#define arch_decomp_wdog() + +static void flush(void) +{ + /* nothing */ +} + +#endif /* ifndef __ASM_ARCH_UNCOMPRESS_H */ diff --git a/include/asm-arm/arch-ns9xxx/vmalloc.h b/include/asm-arm/arch-ns9xxx/vmalloc.h new file mode 100644 index 000000000000..2f3cb6f6be24 --- /dev/null +++ b/include/asm-arm/arch-ns9xxx/vmalloc.h @@ -0,0 +1,16 @@ +/* + * include/asm-arm/arch-ns9xxx/vmalloc.h + * + * Copyright (C) 2006 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#ifndef __ASM_ARCH_VMALLOC_H +#define __ASM_ARCH_VMALLOC_H + +#define VMALLOC_END (0xf0000000) + +#endif /* ifndef __ASM_ARCH_VMALLOC_H */ -- cgit v1.2.3 From b77bfa84c419e3ec8b8e3fd4b4579e5761b7c943 Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Fri, 16 Feb 2007 15:38:49 +0100 Subject: [ARM] 4211/1: Provide a defconfig for ns9xxx This is a follow up for the patch providing the base support for the ns9xxx machine type. Signed-off-by: Uwe Kleine-König Signed-off-by: Russell King --- arch/arm/configs/ns9xxx_defconfig | 621 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 621 insertions(+) create mode 100644 arch/arm/configs/ns9xxx_defconfig (limited to 'arch') diff --git a/arch/arm/configs/ns9xxx_defconfig b/arch/arm/configs/ns9xxx_defconfig new file mode 100644 index 000000000000..0e5794c6a48e --- /dev/null +++ b/arch/arm/configs/ns9xxx_defconfig @@ -0,0 +1,621 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.20 +# Thu Feb 15 20:51:47 2007 +# +CONFIG_ARM=y +# CONFIG_GENERIC_TIME is not set +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_UTS_NS is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +# CONFIG_VM_EVENT_COUNTERS is not set +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +CONFIG_DEFAULT_NOOP=y +CONFIG_DEFAULT_IOSCHED="noop" + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_L7200 is not set +CONFIG_ARCH_NS9XXX=y +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set + +# +# NS9xxx Implementations +# +CONFIG_MACH_CC9P9360DEV=y +CONFIG_PROCESSOR_NS9360=y +CONFIG_BOARD_A9M9750DEV=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set + +# +# Bus support +# + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set +# CONFIG_APM is not set + +# +# Networking +# +# CONFIG_NET is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_NETLINK is not set + +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# ISDN subsystem +# + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +# CONFIG_SERIO_SERPORT is not set +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_8250_MANY_PORTS is not set +# CONFIG_SERIAL_8250_SHARE_IRQ is not set +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# +# Misc devices +# +# CONFIG_TIFM_CORE is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# + +# +# Graphics support +# +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# HID Devices +# +CONFIG_HID=y + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +# CONFIG_USB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_DNOTIFY is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_ENABLE_MUST_CHECK is not set +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DETECT_SOFTLOCKUP is not set +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_RWSEMS is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +CONFIG_DEBUG_ERRORS=y +CONFIG_DEBUG_LL=y +CONFIG_DEBUG_ICEDCC=y + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC32 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_PLIST=y +CONFIG_IOMAP_COPY=y -- cgit v1.2.3 From 66822b2eef8de9fe3ec9fa837386817565dbe690 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Thu, 8 Feb 2007 01:03:17 +0100 Subject: [ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports On the n2100, both onboard r8169 ports exhibit PCI parity problems. Set the ->broken_parity_status flag for both ports so that the r8169 drivers knows it should ignore error interrupts. Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/mach-iop32x/n2100.c | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-iop32x/n2100.c b/arch/arm/mach-iop32x/n2100.c index 2499a7707e3c..966aa51aee09 100644 --- a/arch/arm/mach-iop32x/n2100.c +++ b/arch/arm/mach-iop32x/n2100.c @@ -120,6 +120,20 @@ static struct hw_pci n2100_pci __initdata = { .map_irq = n2100_pci_map_irq, }; +/* + * Both r8169 chips on the n2100 exhibit PCI parity problems. Set + * the ->broken_parity_status flag for both ports so that the r8169 + * driver knows it should ignore error interrupts. + */ +static void n2100_fixup_r8169(struct pci_dev *dev) +{ + if (dev->bus->number == 0 && + (dev->devfn == PCI_DEVFN(1, 0) || + dev->devfn == PCI_DEVFN(2, 0))) + dev->broken_parity_status = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_REALTEK, PCI_ANY_ID, n2100_fixup_r8169); + static int __init n2100_pci_init(void) { if (machine_is_n2100()) -- cgit v1.2.3