From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/char/ip2/i2hw.h | 648 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 648 insertions(+) create mode 100644 drivers/char/ip2/i2hw.h (limited to 'drivers/char/ip2/i2hw.h') diff --git a/drivers/char/ip2/i2hw.h b/drivers/char/ip2/i2hw.h new file mode 100644 index 000000000000..15fe04e748f4 --- /dev/null +++ b/drivers/char/ip2/i2hw.h @@ -0,0 +1,648 @@ +/******************************************************************************* +* +* (c) 1999 by Computone Corporation +* +******************************************************************************** +* +* +* PACKAGE: Linux tty Device Driver for IntelliPort II family of multiport +* serial I/O controllers. +* +* DESCRIPTION: Definitions limited to properties of the hardware or the +* bootstrap firmware. As such, they are applicable regardless of +* operating system or loadware (standard or diagnostic). +* +*******************************************************************************/ +#ifndef I2HW_H +#define I2HW_H 1 +//------------------------------------------------------------------------------ +// Revision History: +// +// 23 September 1991 MAG First Draft Started...through... +// 11 October 1991 ... Continuing development... +// 6 August 1993 Added support for ISA-4 (asic) which is architected +// as an ISA-CEX with a single 4-port box. +// +// 20 December 1996 AKM Version for Linux +// +//------------------------------------------------------------------------------ +/*------------------------------------------------------------------------------ + +HARDWARE DESCRIPTION: + +Introduction: + +The IntelliPort-II and IntelliPort-IIEX products occupy a block of eight (8) +addresses in the host's I/O space. + +Some addresses are used to transfer data to/from the board, some to transfer +so-called "mailbox" messages, and some to read bit-mapped status information. +While all the products in the line are functionally similar, some use a 16-bit +data path to transfer data while others use an 8-bit path. Also, the use of +command /status/mailbox registers differs slightly between the II and IIEX +branches of the family. + +The host determines what type of board it is dealing with by reading a string of +sixteen characters from the board. These characters are always placed in the +fifo by the board's local processor whenever the board is reset (either from +power-on or under software control) and are known as the "Power-on Reset +Message." In order that this message can be read from either type of board, the +hardware registers used in reading this message are the same. Once this message +has been read by the host, then it has the information required to operate. + +General Differences between boards: + +The greatest structural difference is between the -II and -IIEX families of +product. The -II boards use the Am4701 dual 512x8 bidirectional fifo to support +the data path, mailbox registers, and status registers. This chip contains some +features which are not used in the IntelliPort-II products; a description of +these is omitted here. Because of these many features, it contains many +registers, too many to access directly within a small address space. They are +accessed by first writing a value to a "pointer" register. This value selects +the register to be accessed. The next read or write to that address accesses +the selected register rather than the pointer register. + +The -IIEX boards use a proprietary design similar to the Am4701 in function. But +because of a simpler, more streamlined design it doesn't require so many +registers. This means they can be accessed directly in single operations rather +than through a pointer register. + +Besides these differences, there are differences in whether 8-bit or 16-bit +transfers are used to move data to the board. + +The -II boards are capable only of 8-bit data transfers, while the -IIEX boards +may be configured for either 8-bit or 16-bit data transfers. If the on-board DIP +switch #8 is ON, and the card has been installed in a 16-bit slot, 16-bit +transfers are supported (and will be expected by the standard loadware). The +on-board firmware can determine the position of the switch, and whether the +board is installed in a 16-bit slot; it supplies this information to the host as +part of the power-up reset message. + +The configuration switch (#8) and slot selection do not directly configure the +hardware. It is up to the on-board loadware and host-based drivers to act +according to the selected options. That is, loadware and drivers could be +written to perform 8-bit transfers regardless of the state of the DIP switch or +slot (and in a diagnostic environment might well do so). Likewise, 16-bit +transfers could be performed as long as the card is in a 16-bit slot. + +Note the slot selection and DIP switch selection are provided separately: a +board running in 8-bit mode in a 16-bit slot has a greater range of possible +interrupts to choose from; information of potential use to the host. + +All 8-bit data transfers are done in the same way, regardless of whether on a +-II board or a -IIEX board. + +The host must consider two things then: 1) whether a -II or -IIEX product is +being used, and 2) whether an 8-bit or 16-bit data path is used. + +A further difference is that -II boards always have a 512-byte fifo operating in +each direction. -IIEX boards may use fifos of varying size; this size is +reported as part of the power-up message. + +I/O Map Of IntelliPort-II and IntelliPort-IIEX boards: +(Relative to the chosen base address) + +Addr R/W IntelliPort-II IntelliPort-IIEX +---- --- -------------- ---------------- +0 R/W Data Port (byte) Data Port (byte or word) +1 R/W (Not used) (MSB of word-wide data written to Data Port) +2 R Status Register Status Register +2 W Pointer Register Interrupt Mask Register +3 R/W (Not used) Mailbox Registers (6 bits: 11111100) +4,5 -- Reserved for future products +6 -- Reserved for future products +7 R Guaranteed to have no effect +7 W Hardware reset of board. + + +Rules: +All data transfers are performed using the even i/o address. If byte-wide data +transfers are being used, do INB/OUTB operations on the data port. If word-wide +transfers are used, do INW/OUTW operations. In some circumstances (such as +reading the power-up message) you will do INB from the data port, but in this +case the MSB of each word read is lost. When accessing all other unreserved +registers, use byte operations only. +------------------------------------------------------------------------------*/ + +//------------------------------------------------ +// Mandatory Includes: +//------------------------------------------------ +// +#include "ip2types.h" +#include "i2os.h" /* For any o.s., compiler, or host-related issues */ + +//------------------------------------------------------------------------- +// Manifests for the I/O map: +//------------------------------------------------------------------------- +// R/W: Data port (byte) for IntelliPort-II, +// R/W: Data port (byte or word) for IntelliPort-IIEX +// Incoming or outgoing data passes through a FIFO, the status of which is +// available in some of the bits in FIFO_STATUS. This (bidirectional) FIFO is +// the primary means of transferring data, commands, flow-control, and status +// information between the host and board. +// +#define FIFO_DATA 0 + +// Another way of passing information between the board and the host is +// through "mailboxes". Unlike a FIFO, a mailbox holds only a single byte of +// data. Writing data to the mailbox causes a status bit to be set, and +// potentially interrupting the intended receiver. The sender has some way to +// determine whether the data has been read yet; as soon as it has, it may send +// more. The mailboxes are handled differently on -II and -IIEX products, as +// suggested below. +//------------------------------------------------------------------------------ +// Read: Status Register for IntelliPort-II or -IIEX +// The presence of any bit set here will cause an interrupt to the host, +// provided the corresponding bit has been unmasked in the interrupt mask +// register. Furthermore, interrupts to the host are disabled globally until the +// loadware selects the irq line to use. With the exception of STN_MR, the bits +// remain set so long as the associated condition is true. +// +#define FIFO_STATUS 2 + +// Bit map of status bits which are identical for -II and -IIEX +// +#define ST_OUT_FULL 0x40 // Outbound FIFO full +#define ST_IN_EMPTY 0x20 // Inbound FIFO empty +#define ST_IN_MAIL 0x04 // Inbound Mailbox full + +// The following exists only on the Intelliport-IIEX, and indicates that the +// board has not read the last outgoing mailbox data yet. In the IntelliPort-II, +// the outgoing mailbox may be read back: a zero indicates the board has read +// the data. +// +#define STE_OUT_MAIL 0x80 // Outbound mailbox full (!) + +// The following bits are defined differently for -II and -IIEX boards. Code +// which relies on these bits will need to be functionally different for the two +// types of boards and should be generally avoided because of the additional +// complexity this creates: + +// Bit map of status bits only on -II + +// Fifo has been RESET (cleared when the status register is read). Note that +// this condition cannot be masked and would always interrupt the host, except +// that the hardware reset also disables interrupts globally from the board +// until re-enabled by loadware. This could also arise from the +// Am4701-supported command to reset the chip, but this command is generally not +// used here. +// +#define STN_MR 0x80 + +// See the AMD Am4701 data sheet for details on the following four bits. They +// are not presently used by Computone drivers. +// +#define STN_OUT_AF 0x10 // Outbound FIFO almost full (programmable) +#define STN_IN_AE 0x08 // Inbound FIFO almost empty (programmable) +#define STN_BD 0x02 // Inbound byte detected +#define STN_PE 0x01 // Parity/Framing condition detected + +// Bit-map of status bits only on -IIEX +// +#define STE_OUT_HF 0x10 // Outbound FIFO half full +#define STE_IN_HF 0x08 // Inbound FIFO half full +#define STE_IN_FULL 0x02 // Inbound FIFO full +#define STE_OUT_MT 0x01 // Outbound FIFO empty + +//------------------------------------------------------------------------------ + +// Intelliport-II -- Write Only: the pointer register. +// Values are written to this register to select the Am4701 internal register to +// be accessed on the next operation. +// +#define FIFO_PTR 0x02 + +// Values for the pointer register +// +#define SEL_COMMAND 0x1 // Selects the Am4701 command register + +// Some possible commands: +// +#define SEL_CMD_MR 0x80 // Am4701 command to reset the chip +#define SEL_CMD_SH 0x40 // Am4701 command to map the "other" port into the + // status register. +#define SEL_CMD_UNSH 0 // Am4701 command to "unshift": port maps into its + // own status register. +#define SEL_MASK 0x2 // Selects the Am4701 interrupt mask register. The + // interrupt mask register is bit-mapped to match + // the status register (FIFO_STATUS) except for + // STN_MR. (See above.) +#define SEL_BYTE_DET 0x3 // Selects the Am4701 byte-detect register. (Not + // normally used except in diagnostics.) +#define SEL_OUTMAIL 0x4 // Selects the outbound mailbox (R/W). Reading back + // a value of zero indicates that the mailbox has + // been read by the board and is available for more + // data./ Writing to the mailbox optionally + // interrupts the board, depending on the loadware's + // setting of its interrupt mask register. +#define SEL_AEAF 0x5 // Selects AE/AF threshold register. +#define SEL_INMAIL 0x6 // Selects the inbound mailbox (Read) + +//------------------------------------------------------------------------------ +// IntelliPort-IIEX -- Write Only: interrupt mask (and misc flags) register: +// Unlike IntelliPort-II, bit assignments do NOT match those of the status +// register. +// +#define FIFO_MASK 0x2 + +// Mailbox readback select: +// If set, reads to FIFO_MAIL will read the OUTBOUND mailbox (host to board). If +// clear (default on reset) reads to FIFO_MAIL will read the INBOUND mailbox. +// This is the normal situation. The clearing of a mailbox is determined on +// -IIEX boards by waiting for the STE_OUT_MAIL bit to clear. Readback +// capability is provided for diagnostic purposes only. +// +#define MX_OUTMAIL_RSEL 0x80 + +#define MX_IN_MAIL 0x40 // Enables interrupts when incoming mailbox goes + // full (ST_IN_MAIL set). +#define MX_IN_FULL 0x20 // Enables interrupts when incoming FIFO goes full + // (STE_IN_FULL). +#define MX_IN_MT 0x08 // Enables interrupts when incoming FIFO goes empty + // (ST_IN_MT). +#define MX_OUT_FULL 0x04 // Enables interrupts when outgoing FIFO goes full + // (ST_OUT_FULL). +#define MX_OUT_MT 0x01 // Enables interrupts when outgoing FIFO goes empty + // (STE_OUT_MT). + +// Any remaining bits are reserved, and should be written to ZERO for +// compatibility with future Computone products. + +//------------------------------------------------------------------------------ +// IntelliPort-IIEX: -- These are only 6-bit mailboxes !!! -- 11111100 (low two +// bits always read back 0). +// Read: One of the mailboxes, usually Inbound. +// Inbound Mailbox (MX_OUTMAIL_RSEL = 0) +// Outbound Mailbox (MX_OUTMAIL_RSEL = 1) +// Write: Outbound Mailbox +// For the IntelliPort-II boards, the outbound mailbox is read back to determine +// whether the board has read the data (0 --> data has been read). For the +// IntelliPort-IIEX, this is done by reading a status register. To determine +// whether mailbox is available for more outbound data, use the STE_OUT_MAIL bit +// in FIFO_STATUS. Moreover, although the Outbound Mailbox can be read back by +// setting MX_OUTMAIL_RSEL, it is NOT cleared when the board reads it, as is the +// case with the -II boards. For this reason, FIFO_MAIL is normally used to read +// the inbound FIFO, and MX_OUTMAIL_RSEL kept clear. (See above for +// MX_OUTMAIL_RSEL description.) +// +#define FIFO_MAIL 0x3 + +//------------------------------------------------------------------------------ +// WRITE ONLY: Resets the board. (Data doesn't matter). +// +#define FIFO_RESET 0x7 + +//------------------------------------------------------------------------------ +// READ ONLY: Will have no effect. (Data is undefined.) +// Actually, there will be an effect, in that the operation is sure to generate +// a bus cycle: viz., an I/O byte Read. This fact can be used to enforce short +// delays when no comparable time constant is available. +// +#define FIFO_NOP 0x7 + +//------------------------------------------------------------------------------ +// RESET & POWER-ON RESET MESSAGE +/*------------------------------------------------------------------------------ +RESET: + +The IntelliPort-II and -IIEX boards are reset in three ways: Power-up, channel +reset, and via a write to the reset register described above. For products using +the ISA bus, these three sources of reset are equvalent. For MCA and EISA buses, +the Power-up and channel reset sources cause additional hardware initialization +which should only occur at system startup time. + +The third type of reset, called a "command reset", is done by writing any data +to the FIFO_RESET address described above. This resets the on-board processor, +FIFO, UARTS, and associated hardware. + +This passes control of the board to the bootstrap firmware, which performs a +Power-On Self Test and which detects its current configuration. For example, +-IIEX products determine the size of FIFO which has been installed, and the +number and type of expansion boxes attached. + +This and other information is then written to the FIFO in a 16-byte data block +to be read by the host. This block is guaranteed to be present within two (2) +seconds of having received the command reset. The firmware is now ready to +receive loadware from the host. + +It is good practice to perform a command reset to the board explicitly as part +of your software initialization. This allows your code to properly restart from +a soft boot. (Many systems do not issue channel reset on soft boot). + +Because of a hardware reset problem on some of the Cirrus Logic 1400's which are +used on the product, it is recommended that you reset the board twice, separated +by an approximately 50 milliseconds delay. (VERY approximately: probably ok to +be off by a factor of five. The important point is that the first command reset +in fact generates a reset pulse on the board. This pulse is guaranteed to last +less than 10 milliseconds. The additional delay ensures the 1400 has had the +chance to respond sufficiently to the first reset. Why not a longer delay? Much +more than 50 milliseconds gets to be noticable, but the board would still work. + +Once all 16 bytes of the Power-on Reset Message have been read, the bootstrap +firmware is ready to receive loadware. + +Note on Power-on Reset Message format: +The various fields have been designed with future expansion in view. +Combinations of bitfields and values have been defined which define products +which may not currently exist. This has been done to allow drivers to anticipate +the possible introduction of products in a systematic fashion. This is not +intended to suggest that each potential product is actually under consideration. +------------------------------------------------------------------------------*/ + +//---------------------------------------- +// Format of Power-on Reset Message +//---------------------------------------- + +typedef union _porStr // "por" stands for Power On Reset +{ + unsigned char c[16]; // array used when considering the message as a + // string of undifferentiated characters + + struct // Elements used when considering values + { + // The first two bytes out of the FIFO are two magic numbers. These are + // intended to establish that there is indeed a member of the + // IntelliPort-II(EX) family present. The remaining bytes may be + // expected // to be valid. When reading the Power-on Reset message, + // if the magic numbers do not match it is probably best to stop + // reading immediately. You are certainly not reading our board (unless + // hardware is faulty), and may in fact be reading some other piece of + // hardware. + + unsigned char porMagic1; // magic number: first byte == POR_MAGIC_1 + unsigned char porMagic2; // magic number: second byte == POR_MAGIC_2 + + // The Version, Revision, and Subrevision are stored as absolute numbers + // and would normally be displayed in the format V.R.S (e.g. 1.0.2) + + unsigned char porVersion; // Bootstrap firmware version number + unsigned char porRevision; // Bootstrap firmware revision number + unsigned char porSubRev; // Bootstrap firmware sub-revision number + + unsigned char porID; // Product ID: Bit-mapped according to + // conventions described below. Among other + // things, this allows us to distinguish + // IntelliPort-II boards from IntelliPort-IIEX + // boards. + + unsigned char porBus; // IntelliPort-II: Unused + // IntelliPort-IIEX: Bus Information: + // Bit-mapped below + + unsigned char porMemory; // On-board DRAM size: in 32k blocks + + // porPorts1 (and porPorts2) are used to determine the ports which are + // available to the board. For non-expandable product, a single number + // is sufficient. For expandable product, the board may be connected + // to as many as four boxes. Each box may be (so far) either a 16-port + // or an 8-port size. Whenever an 8-port box is used, the remaining 8 + // ports leave gaps between existing channels. For that reason, + // expandable products must report a MAP of available channels. Since + // each UART supports four ports, we represent each UART found by a + // single bit. Using two bytes to supply the mapping information we + // report the presense or absense of up to 16 UARTS, or 64 ports in + // steps of 4 ports. For -IIEX products, the ports are numbered + // starting at the box closest to the controller in the "chain". + + // Interpreted Differently for IntelliPort-II and -IIEX. + // -II: Number of ports (Derived actually from product ID). See + // Diag1&2 to indicate if uart was actually detected. + // -IIEX: Bit-map of UARTS found, LSB (see below for MSB of this). This + // bitmap is based on detecting the uarts themselves; + // see porFlags for information from the box i.d's. + unsigned char porPorts1; + + unsigned char porDiag1; // Results of on-board P.O.S.T, 1st byte + unsigned char porDiag2; // Results of on-board P.O.S.T, 2nd byte + unsigned char porSpeed; // Speed of local CPU: given as MHz x10 + // e.g., 16.0 MHz CPU is reported as 160 + unsigned char porFlags; // Misc information (see manifests below) + // Bit-mapped: CPU type, UART's present + + unsigned char porPorts2; // -II: Undefined + // -IIEX: Bit-map of UARTS found, MSB (see + // above for LSB) + + // IntelliPort-II: undefined + // IntelliPort-IIEX: 1 << porFifoSize gives the size, in bytes, of the + // host interface FIFO, in each direction. When running the -IIEX in + // 8-bit mode, fifo capacity is halved. The bootstrap firmware will + // have already accounted for this fact in generating this number. + unsigned char porFifoSize; + + // IntelliPort-II: undefined + // IntelliPort-IIEX: The number of boxes connected. (Presently 1-4) + unsigned char porNumBoxes; + } e; +} porStr, *porStrPtr; + +//-------------------------- +// Values for porStr fields +//-------------------------- + +//--------------------- +// porMagic1, porMagic2 +//---------------------- +// +#define POR_MAGIC_1 0x96 // The only valid value for porMagic1 +#define POR_MAGIC_2 0x35 // The only valid value for porMagic2 +#define POR_1_INDEX 0 // Byte position of POR_MAGIC_1 +#define POR_2_INDEX 1 // Ditto for POR_MAGIC_2 + +//---------------------- +// porID +//---------------------- +// +#define POR_ID_FAMILY 0xc0 // These bits indicate the general family of + // product. +#define POR_ID_FII 0x00 // Family is "IntelliPort-II" +#define POR_ID_FIIEX 0x40 // Family is "IntelliPort-IIEX" + +// These bits are reserved, presently zero. May be used at a later date to +// convey other product information. +// +#define POR_ID_RESERVED 0x3c + +#define POR_ID_SIZE 0x03 // Remaining bits indicate number of ports & + // Connector information. +#define POR_ID_II_8 0x00 // For IntelliPort-II, indicates 8-port using + // standard brick. +#define POR_ID_II_8R 0x01 // For IntelliPort-II, indicates 8-port using + // RJ11's (no CTS) +#define POR_ID_II_6 0x02 // For IntelliPort-II, indicates 6-port using + // RJ45's +#define POR_ID_II_4 0x03 // For IntelliPort-II, indicates 4-port using + // 4xRJ45 connectors +#define POR_ID_EX 0x00 // For IntelliPort-IIEX, indicates standard + // expandable controller (other values reserved) + +//---------------------- +// porBus +//---------------------- + +// IntelliPort-IIEX only: Board is installed in a 16-bit slot +// +#define POR_BUS_SLOT16 0x20 + +// IntelliPort-IIEX only: DIP switch #8 is on, selecting 16-bit host interface +// operation. +// +#define POR_BUS_DIP16 0x10 + +// Bits 0-2 indicate type of bus: This information is stored in the bootstrap +// loadware, different loadware being used on different products for different +// buses. For most situations, the drivers do not need this information; but it +// is handy in a diagnostic environment. For example, on microchannel boards, +// you would not want to try to test several interrupts, only the one for which +// you were configured. +// +#define POR_BUS_TYPE 0x07 + +// Unknown: this product doesn't know what bus it is running in. (e.g. if same +// bootstrap firmware were wanted for two different buses.) +// +#define POR_BUS_T_UNK 0 + +// Note: existing firmware for ISA-8 and MC-8 currently report the POR_BUS_T_UNK +// state, since the same bootstrap firmware is used for each. + +#define POR_BUS_T_MCA 1 // MCA BUS */ +#define POR_BUS_T_EISA 2 // EISA BUS */ +#define POR_BUS_T_ISA 3 // ISA BUS */ + +// Values 4-7 Reserved + +// Remaining bits are reserved + +//---------------------- +// porDiag1 +//---------------------- + +#define POR_BAD_MAPPER 0x80 // HW failure on P.O.S.T: Chip mapper failed + +// These two bits valid only for the IntelliPort-II +// +#define POR_BAD_UART1 0x01 // First 1400 bad +#define POR_BAD_UART2 0x02 // Second 1400 bad + +//---------------------- +// porDiag2 +//---------------------- + +#define POR_DEBUG_PORT 0x80 // debug port was detected by the P.O.S.T +#define POR_DIAG_OK 0x00 // Indicates passage: Failure codes not yet + // available. + // Other bits undefined. +//---------------------- +// porFlags +//---------------------- + +#define POR_CPU 0x03 // These bits indicate supposed CPU type +#define POR_CPU_8 0x01 // Board uses an 80188 (no such thing yet) +#define POR_CPU_6 0x02 // Board uses an 80186 (all existing products) +#define POR_CEX4 0x04 // If set, this is an ISA-CEX/4: An ISA-4 (asic) + // which is architected like an ISA-CEX connected + // to a (hitherto impossible) 4-port box. +#define POR_BOXES 0xf0 // Valid for IntelliPort-IIEX only: Map of Box + // sizes based on box I.D. +#define POR_BOX_16 0x10 // Set indicates 16-port, clear 8-port + +//------------------------------------- +// LOADWARE and DOWNLOADING CODE +//------------------------------------- + +/* +Loadware may be sent to the board in two ways: +1) It may be read from a (binary image) data file block by block as each block + is sent to the board. This is only possible when the initialization is + performed by code which can access your file system. This is most suitable + for diagnostics and appications which use the interface library directly. + +2) It may be hard-coded into your source by including a .h file (typically + supplied by Computone), which declares a data array and initializes every + element. This acheives the same result as if an entire loadware file had + been read into the array. + + This requires more data space in your program, but access to the file system + is not required. This method is more suited to driver code, which typically + is running at a level too low to access the file system directly. + +At present, loadware can only be generated at Computone. + +All Loadware begins with a header area which has a particular format. This +includes a magic number which identifies the file as being (purportedly) +loadware, CRC (for the loader), and version information. +*/ + + +//----------------------------------------------------------------------------- +// Format of loadware block +// +// This is defined as a union so we can pass a pointer to one of these items +// and (if it is the first block) pick out the version information, etc. +// +// Otherwise, to deal with this as a simple character array +//------------------------------------------------------------------------------ + +#define LOADWARE_BLOCK_SIZE 512 // Number of bytes in each block of loadware + +typedef union _loadHdrStr +{ + unsigned char c[LOADWARE_BLOCK_SIZE]; // Valid for every block + + struct // These fields are valid for only the first block of loadware. + { + unsigned char loadMagic; // Magic number: see below + unsigned char loadBlocksMore; // How many more blocks? + unsigned char loadCRC[2]; // Two CRC bytes: used by loader + unsigned char loadVersion; // Version number + unsigned char loadRevision; // Revision number + unsigned char loadSubRevision; // Sub-revision number + unsigned char loadSpares[9]; // Presently unused + unsigned char loadDates[32]; // Null-terminated string which can give + // date and time of compilation + } e; +} loadHdrStr, *loadHdrStrPtr; + +//------------------------------------ +// Defines for downloading code: +//------------------------------------ + +// The loadMagic field in the first block of the loadfile must be this, else the +// file is not valid. +// +#define MAGIC_LOADFILE 0x3c + +// How do we know the load was successful? On completion of the load, the +// bootstrap firmware returns a code to indicate whether it thought the download +// was valid and intends to execute it. These are the only possible valid codes: +// +#define LOADWARE_OK 0xc3 // Download was ok +#define LOADWARE_BAD 0x5a // Download was bad (CRC error) + +// Constants applicable to writing blocks of loadware: +// The first block of loadware might take 600 mS to load, in extreme cases. +// (Expandable board: worst case for sending startup messages to the LCD's). +// The 600mS figure is not really a calculation, but a conservative +// guess/guarantee. Usually this will be within 100 mS, like subsequent blocks. +// +#define MAX_DLOAD_START_TIME 1000 // 1000 mS +#define MAX_DLOAD_READ_TIME 100 // 100 mS + +// Firmware should respond with status (see above) within this long of host +// having sent the final block. +// +#define MAX_DLOAD_ACK_TIME 100 // 100 mS, again! + +//------------------------------------------------------ +// MAXIMUM NUMBER OF PORTS PER BOARD: +// This is fixed for now (with the expandable), but may +// be expanding according to even newer products. +//------------------------------------------------------ +// +#define ABS_MAX_BOXES 4 // Absolute most boxes per board +#define ABS_BIGGEST_BOX 16 // Absolute the most ports per box +#define ABS_MOST_PORTS (ABS_MAX_BOXES * ABS_BIGGEST_BOX) + +#endif // I2HW_H + -- cgit v1.2.3