From 15e0c694367332d7e7114c7c73044bc5fed9ee48 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Wed, 12 Jul 2006 15:05:41 +0100 Subject: [PATCH] ide: fix Jmicron support Prior to 2.6.18rc1 you could install with devices on a JMicron chipset using the "all-generic-ide" option. As of this kernel the AHCI driver grabs the controller and rams it into AHCI mode losing the PATA ports and making CD drives and the like vanish. The all-generic-ide option fails because the AHCI driver grabbed the PCI device and reconfigured it. To fix this three things are needed. #1 We must put the chip into dual function mode #2 The AHCI driver must grab only function 0 (already in your rc1 tree) #3 Something must grab the PATA ports The attached patch is the minimal risk edition of this. It puts the chip into dual function mode so that AHCI will grab the SATA ports without losing the PATA ports. To keep the risk as low as possible the third patch adds the PCI identifiers for the PATA port and the FN check to the ide-generic driver. There is a more featured jmicron driver on its way but that adds risk and the ide-generic support is sufficient to install and run a system. The actual chip setup done by the quirk is the precise setup recommended by the vendor. (The JMB368 appears only in the ide-generic entry as it has no AHCI so does not need the quirk) Signed-off-by: Alan Cox Acked-by: Jeff Garzik Signed-off-by: Linus Torvalds --- drivers/pci/quirks.c | 49 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) (limited to 'drivers/pci') diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index e9a57afa1a08..de3bbc88fb26 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -1175,6 +1175,55 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus ); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus ); +#if defined(CONFIG_SCSI_SATA) || defined(CONFIG_SCSI_SATA_MODULE) + +/* + * If we are using libata we can drive this chip properly but must + * do this early on to make the additional device appear during + * the PCI scanning. + */ + +static void __devinit quirk_jmicron_dualfn(struct pci_dev *pdev) +{ + u32 conf; + u8 hdr; + + /* Only poke fn 0 */ + if (PCI_FUNC(pdev->devfn)) + return; + + switch(pdev->device) { + case PCI_DEVICE_ID_JMICRON_JMB365: + case PCI_DEVICE_ID_JMICRON_JMB366: + /* Redirect IDE second PATA port to the right spot */ + pci_read_config_dword(pdev, 0x80, &conf); + conf |= (1 << 24); + /* Fall through */ + pci_write_config_dword(pdev, 0x80, conf); + case PCI_DEVICE_ID_JMICRON_JMB361: + case PCI_DEVICE_ID_JMICRON_JMB363: + pci_read_config_dword(pdev, 0x40, &conf); + /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ + /* Set the class codes correctly and then direct IDE 0 */ + conf &= ~0x000F0200; /* Clear bit 9 and 16-19 */ + conf |= 0x00C20002; /* Set bit 1, 17, 22, 23 */ + pci_write_config_dword(pdev, 0x40, conf); + + /* Reconfigure so that the PCI scanner discovers the + device is now multifunction */ + + pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr); + pdev->hdr_type = hdr & 0x7f; + pdev->multifunction = !!(hdr & 0x80); + + break; + } +} + +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, quirk_jmicron_dualfn); + +#endif + #ifdef CONFIG_X86_IO_APIC static void __init quirk_alder_ioapic(struct pci_dev *pdev) { -- cgit v1.2.3