From 02dca8c981b552ad4caaa2e858800c78cc20f41c Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Mon, 29 Jun 2020 20:24:52 +0530 Subject: phy: qcom: remove ufs qmp phy driver The UFS specific QMP PHY driver started off supporting the 14nm and 20nm hardware. With the 20nm support marked broken for a long time and the 14nm support added to the common QMP PHY, this driver has not been used in a while. So delete it Reviewed-by: Bjorn Andersson Link: https://lore.kernel.org/r/20200629145452.123035-1-vkoul@kernel.org Signed-off-by: Vinod Koul --- drivers/phy/qualcomm/Kconfig | 24 - drivers/phy/qualcomm/Makefile | 3 - drivers/phy/qualcomm/phy-qcom-ufs-i.h | 131 ------ drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c | 172 ------- drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h | 168 ------- drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c | 226 ---------- drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h | 226 ---------- drivers/phy/qualcomm/phy-qcom-ufs.c | 648 --------------------------- 8 files changed, 1598 deletions(-) delete mode 100644 drivers/phy/qualcomm/phy-qcom-ufs-i.h delete mode 100644 drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c delete mode 100644 drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h delete mode 100644 drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c delete mode 100644 drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h delete mode 100644 drivers/phy/qualcomm/phy-qcom-ufs.c (limited to 'drivers/phy/qualcomm') diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig index ca9ce7e84a5c..e6f0e514fb1f 100644 --- a/drivers/phy/qualcomm/Kconfig +++ b/drivers/phy/qualcomm/Kconfig @@ -59,30 +59,6 @@ config PHY_QCOM_QUSB2 PHY which is usually paired with either the ChipIdea or Synopsys DWC3 USB IPs on MSM SOCs. -config PHY_QCOM_UFS - tristate "Qualcomm UFS PHY driver" - depends on OF && ARCH_QCOM - select GENERIC_PHY - help - Support for UFS PHY on QCOM chipsets. - -if PHY_QCOM_UFS - -config PHY_QCOM_UFS_14NM - tristate - default PHY_QCOM_UFS - help - Support for 14nm UFS QMP phy present on QCOM chipsets. - -config PHY_QCOM_UFS_20NM - tristate - default PHY_QCOM_UFS - depends on BROKEN - help - Support for 20nm UFS QMP phy present on QCOM chipsets. - -endif - config PHY_QCOM_USB_HS tristate "Qualcomm USB HS PHY module" depends on USB_ULPI_BUS diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile index 86fb32efab79..a767915decd0 100644 --- a/drivers/phy/qualcomm/Makefile +++ b/drivers/phy/qualcomm/Makefile @@ -6,9 +6,6 @@ obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o -obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o -obj-$(CONFIG_PHY_QCOM_UFS_14NM) += phy-qcom-ufs-qmp-14nm.o -obj-$(CONFIG_PHY_QCOM_UFS_20NM) += phy-qcom-ufs-qmp-20nm.o obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o obj-$(CONFIG_PHY_QCOM_USB_HS_28NM) += phy-qcom-usb-hs-28nm.o diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-i.h b/drivers/phy/qualcomm/phy-qcom-ufs-i.h deleted file mode 100644 index 9bf973a0d8c3..000000000000 --- a/drivers/phy/qualcomm/phy-qcom-ufs-i.h +++ /dev/null @@ -1,131 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-only */ -/* - * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - */ - -#ifndef UFS_QCOM_PHY_I_H_ -#define UFS_QCOM_PHY_I_H_ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define UFS_QCOM_PHY_CAL_ENTRY(reg, val) \ - { \ - .reg_offset = reg, \ - .cfg_value = val, \ - } - -#define UFS_QCOM_PHY_NAME_LEN 30 - -enum { - MASK_SERDES_START = 0x1, - MASK_PCS_READY = 0x1, -}; - -enum { - OFFSET_SERDES_START = 0x0, -}; - -struct ufs_qcom_phy_stored_attributes { - u32 att; - u32 value; -}; - - -struct ufs_qcom_phy_calibration { - u32 reg_offset; - u32 cfg_value; -}; - -struct ufs_qcom_phy_vreg { - const char *name; - struct regulator *reg; - int max_uA; - int min_uV; - int max_uV; - bool enabled; -}; - -struct ufs_qcom_phy { - struct list_head list; - struct device *dev; - void __iomem *mmio; - void __iomem *dev_ref_clk_ctrl_mmio; - struct clk *tx_iface_clk; - struct clk *rx_iface_clk; - bool is_iface_clk_enabled; - struct clk *ref_clk_src; - struct clk *ref_clk_parent; - struct clk *ref_clk; - bool is_ref_clk_enabled; - bool is_dev_ref_clk_enabled; - struct ufs_qcom_phy_vreg vdda_pll; - struct ufs_qcom_phy_vreg vdda_phy; - struct ufs_qcom_phy_vreg vddp_ref_clk; - unsigned int quirks; - - /* - * If UFS link is put into Hibern8 and if UFS PHY analog hardware is - * power collapsed (by clearing UFS_PHY_POWER_DOWN_CONTROL), Hibern8 - * exit might fail even after powering on UFS PHY analog hardware. - * Enabling this quirk will help to solve above issue by doing - * custom PHY settings just before PHY analog power collapse. - */ - #define UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE BIT(0) - - u8 host_ctrl_rev_major; - u16 host_ctrl_rev_minor; - u16 host_ctrl_rev_step; - - char name[UFS_QCOM_PHY_NAME_LEN]; - struct ufs_qcom_phy_calibration *cached_regs; - int cached_regs_table_size; - struct ufs_qcom_phy_specific_ops *phy_spec_ops; - - enum phy_mode mode; - struct reset_control *ufs_reset; -}; - -/** - * struct ufs_qcom_phy_specific_ops - set of pointers to functions which have a - * specific implementation per phy. Each UFS phy, should implement - * those functions according to its spec and requirements - * @start_serdes: pointer to a function that starts the serdes - * @is_physical_coding_sublayer_ready: pointer to a function that - * checks pcs readiness. returns 0 for success and non-zero for error. - * @set_tx_lane_enable: pointer to a function that enable tx lanes - * @power_control: pointer to a function that controls analog rail of phy - * and writes to QSERDES_RX_SIGDET_CNTRL attribute - */ -struct ufs_qcom_phy_specific_ops { - int (*calibrate)(struct ufs_qcom_phy *ufs_qcom_phy, bool is_rate_B); - void (*start_serdes)(struct ufs_qcom_phy *phy); - int (*is_physical_coding_sublayer_ready)(struct ufs_qcom_phy *phy); - void (*set_tx_lane_enable)(struct ufs_qcom_phy *phy, u32 val); - void (*power_control)(struct ufs_qcom_phy *phy, bool val); -}; - -struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy); -int ufs_qcom_phy_power_on(struct phy *generic_phy); -int ufs_qcom_phy_power_off(struct phy *generic_phy); -int ufs_qcom_phy_init_clks(struct ufs_qcom_phy *phy_common); -int ufs_qcom_phy_init_vregulators(struct ufs_qcom_phy *phy_common); -int ufs_qcom_phy_remove(struct phy *generic_phy, - struct ufs_qcom_phy *ufs_qcom_phy); -struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev, - struct ufs_qcom_phy *common_cfg, - const struct phy_ops *ufs_qcom_phy_gen_ops, - struct ufs_qcom_phy_specific_ops *phy_spec_ops); -int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, - struct ufs_qcom_phy_calibration *tbl_A, int tbl_size_A, - struct ufs_qcom_phy_calibration *tbl_B, int tbl_size_B, - bool is_rate_B); -#endif diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c deleted file mode 100644 index 54b355bfc24c..000000000000 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c +++ /dev/null @@ -1,172 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - */ - -#include "phy-qcom-ufs-qmp-14nm.h" - -#define UFS_PHY_NAME "ufs_phy_qmp_14nm" -#define UFS_PHY_VDDA_PHY_UV (925000) - -static -int ufs_qcom_phy_qmp_14nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, - bool is_rate_B) -{ - int tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A); - int tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B); - int err; - - err = ufs_qcom_phy_calibrate(ufs_qcom_phy, phy_cal_table_rate_A, - tbl_size_A, phy_cal_table_rate_B, tbl_size_B, is_rate_B); - - if (err) - dev_err(ufs_qcom_phy->dev, - "%s: ufs_qcom_phy_calibrate() failed %d\n", - __func__, err); - return err; -} - -static -void ufs_qcom_phy_qmp_14nm_advertise_quirks(struct ufs_qcom_phy *phy_common) -{ - phy_common->quirks = - UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; -} - -static -int ufs_qcom_phy_qmp_14nm_set_mode(struct phy *generic_phy, - enum phy_mode mode, int submode) -{ - struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - - phy_common->mode = PHY_MODE_INVALID; - - if (mode > 0) - phy_common->mode = mode; - - return 0; -} - -static -void ufs_qcom_phy_qmp_14nm_power_control(struct ufs_qcom_phy *phy, bool val) -{ - writel_relaxed(val ? 0x1 : 0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); - /* - * Before any transactions involving PHY, ensure PHY knows - * that it's analog rail is powered ON (or OFF). - */ - mb(); -} - -static inline -void ufs_qcom_phy_qmp_14nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val) -{ - /* - * 14nm PHY does not have TX_LANE_ENABLE register. - * Implement this function so as not to propagate error to caller. - */ -} - -static inline void ufs_qcom_phy_qmp_14nm_start_serdes(struct ufs_qcom_phy *phy) -{ - u32 tmp; - - tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START); - tmp &= ~MASK_SERDES_START; - tmp |= (1 << OFFSET_SERDES_START); - writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START); - /* Ensure register value is committed */ - mb(); -} - -static int ufs_qcom_phy_qmp_14nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) -{ - int err = 0; - u32 val; - - err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS, - val, (val & MASK_PCS_READY), 10, 1000000); - if (err) - dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n", - __func__, err); - return err; -} - -static const struct phy_ops ufs_qcom_phy_qmp_14nm_phy_ops = { - .power_on = ufs_qcom_phy_power_on, - .power_off = ufs_qcom_phy_power_off, - .set_mode = ufs_qcom_phy_qmp_14nm_set_mode, - .owner = THIS_MODULE, -}; - -static struct ufs_qcom_phy_specific_ops phy_14nm_ops = { - .calibrate = ufs_qcom_phy_qmp_14nm_phy_calibrate, - .start_serdes = ufs_qcom_phy_qmp_14nm_start_serdes, - .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_14nm_is_pcs_ready, - .set_tx_lane_enable = ufs_qcom_phy_qmp_14nm_set_tx_lane_enable, - .power_control = ufs_qcom_phy_qmp_14nm_power_control, -}; - -static int ufs_qcom_phy_qmp_14nm_probe(struct platform_device *pdev) -{ - struct device *dev = &pdev->dev; - struct phy *generic_phy; - struct ufs_qcom_phy_qmp_14nm *phy; - struct ufs_qcom_phy *phy_common; - int err = 0; - - phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); - if (!phy) { - err = -ENOMEM; - goto out; - } - phy_common = &phy->common_cfg; - - generic_phy = ufs_qcom_phy_generic_probe(pdev, phy_common, - &ufs_qcom_phy_qmp_14nm_phy_ops, &phy_14nm_ops); - - if (!generic_phy) { - err = -EIO; - goto out; - } - - err = ufs_qcom_phy_init_clks(phy_common); - if (err) - goto out; - - err = ufs_qcom_phy_init_vregulators(phy_common); - if (err) - goto out; - - phy_common->vdda_phy.max_uV = UFS_PHY_VDDA_PHY_UV; - phy_common->vdda_phy.min_uV = UFS_PHY_VDDA_PHY_UV; - - ufs_qcom_phy_qmp_14nm_advertise_quirks(phy_common); - - phy_set_drvdata(generic_phy, phy); - - strlcpy(phy_common->name, UFS_PHY_NAME, sizeof(phy_common->name)); - -out: - return err; -} - -static const struct of_device_id ufs_qcom_phy_qmp_14nm_of_match[] = { - {.compatible = "qcom,ufs-phy-qmp-14nm"}, - {.compatible = "qcom,msm8996-ufs-phy-qmp-14nm"}, - {}, -}; -MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_14nm_of_match); - -static struct platform_driver ufs_qcom_phy_qmp_14nm_driver = { - .probe = ufs_qcom_phy_qmp_14nm_probe, - .driver = { - .of_match_table = ufs_qcom_phy_qmp_14nm_of_match, - .name = "ufs_qcom_phy_qmp_14nm", - }, -}; - -module_platform_driver(ufs_qcom_phy_qmp_14nm_driver); - -MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 14nm"); -MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h deleted file mode 100644 index ceca654b9338..000000000000 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h +++ /dev/null @@ -1,168 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-only */ -/* - * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - */ - -#ifndef UFS_QCOM_PHY_QMP_14NM_H_ -#define UFS_QCOM_PHY_QMP_14NM_H_ - -#include "phy-qcom-ufs-i.h" - -/* QCOM UFS PHY control registers */ -#define COM_OFF(x) (0x000 + x) -#define PHY_OFF(x) (0xC00 + x) -#define TX_OFF(n, x) (0x400 + (0x400 * n) + x) -#define RX_OFF(n, x) (0x600 + (0x400 * n) + x) - -/* UFS PHY QSERDES COM registers */ -#define QSERDES_COM_BG_TIMER COM_OFF(0x0C) -#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x34) -#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x3C) -#define QSERDES_COM_LOCK_CMP1_MODE0 COM_OFF(0x4C) -#define QSERDES_COM_LOCK_CMP2_MODE0 COM_OFF(0x50) -#define QSERDES_COM_LOCK_CMP3_MODE0 COM_OFF(0x54) -#define QSERDES_COM_LOCK_CMP1_MODE1 COM_OFF(0x58) -#define QSERDES_COM_LOCK_CMP2_MODE1 COM_OFF(0x5C) -#define QSERDES_COM_LOCK_CMP3_MODE1 COM_OFF(0x60) -#define QSERDES_COM_CP_CTRL_MODE0 COM_OFF(0x78) -#define QSERDES_COM_CP_CTRL_MODE1 COM_OFF(0x7C) -#define QSERDES_COM_PLL_RCTRL_MODE0 COM_OFF(0x84) -#define QSERDES_COM_PLL_RCTRL_MODE1 COM_OFF(0x88) -#define QSERDES_COM_PLL_CCTRL_MODE0 COM_OFF(0x90) -#define QSERDES_COM_PLL_CCTRL_MODE1 COM_OFF(0x94) -#define QSERDES_COM_SYSCLK_EN_SEL COM_OFF(0xAC) -#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0xB4) -#define QSERDES_COM_LOCK_CMP_EN COM_OFF(0xC8) -#define QSERDES_COM_LOCK_CMP_CFG COM_OFF(0xCC) -#define QSERDES_COM_DEC_START_MODE0 COM_OFF(0xD0) -#define QSERDES_COM_DEC_START_MODE1 COM_OFF(0xD4) -#define QSERDES_COM_DIV_FRAC_START1_MODE0 COM_OFF(0xDC) -#define QSERDES_COM_DIV_FRAC_START2_MODE0 COM_OFF(0xE0) -#define QSERDES_COM_DIV_FRAC_START3_MODE0 COM_OFF(0xE4) -#define QSERDES_COM_DIV_FRAC_START1_MODE1 COM_OFF(0xE8) -#define QSERDES_COM_DIV_FRAC_START2_MODE1 COM_OFF(0xEC) -#define QSERDES_COM_DIV_FRAC_START3_MODE1 COM_OFF(0xF0) -#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 COM_OFF(0x108) -#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 COM_OFF(0x10C) -#define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 COM_OFF(0x110) -#define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 COM_OFF(0x114) -#define QSERDES_COM_VCO_TUNE_CTRL COM_OFF(0x124) -#define QSERDES_COM_VCO_TUNE_MAP COM_OFF(0x128) -#define QSERDES_COM_VCO_TUNE1_MODE0 COM_OFF(0x12C) -#define QSERDES_COM_VCO_TUNE2_MODE0 COM_OFF(0x130) -#define QSERDES_COM_VCO_TUNE1_MODE1 COM_OFF(0x134) -#define QSERDES_COM_VCO_TUNE2_MODE1 COM_OFF(0x138) -#define QSERDES_COM_VCO_TUNE_TIMER1 COM_OFF(0x144) -#define QSERDES_COM_VCO_TUNE_TIMER2 COM_OFF(0x148) -#define QSERDES_COM_CLK_SELECT COM_OFF(0x174) -#define QSERDES_COM_HSCLK_SEL COM_OFF(0x178) -#define QSERDES_COM_CORECLK_DIV COM_OFF(0x184) -#define QSERDES_COM_CORE_CLK_EN COM_OFF(0x18C) -#define QSERDES_COM_CMN_CONFIG COM_OFF(0x194) -#define QSERDES_COM_SVS_MODE_CLK_SEL COM_OFF(0x19C) -#define QSERDES_COM_CORECLK_DIV_MODE1 COM_OFF(0x1BC) - -/* UFS PHY registers */ -#define UFS_PHY_PHY_START PHY_OFF(0x00) -#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x04) -#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x168) - -/* UFS PHY TX registers */ -#define QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN TX_OFF(0, 0x68) -#define QSERDES_TX_LANE_MODE TX_OFF(0, 0x94) - -/* UFS PHY RX registers */ -#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN RX_OFF(0, 0x40) -#define QSERDES_RX_RX_TERM_BW RX_OFF(0, 0x90) -#define QSERDES_RX_RX_EQ_GAIN1_LSB RX_OFF(0, 0xC4) -#define QSERDES_RX_RX_EQ_GAIN1_MSB RX_OFF(0, 0xC8) -#define QSERDES_RX_RX_EQ_GAIN2_LSB RX_OFF(0, 0xCC) -#define QSERDES_RX_RX_EQ_GAIN2_MSB RX_OFF(0, 0xD0) -#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 RX_OFF(0, 0xD8) -#define QSERDES_RX_SIGDET_CNTRL RX_OFF(0, 0x114) -#define QSERDES_RX_SIGDET_LVL RX_OFF(0, 0x118) -#define QSERDES_RX_SIGDET_DEGLITCH_CNTRL RX_OFF(0, 0x11C) -#define QSERDES_RX_RX_INTERFACE_MODE RX_OFF(0, 0x12C) - -/* - * This structure represents the 14nm specific phy. - * common_cfg MUST remain the first field in this structure - * in case extra fields are added. This way, when calling - * get_ufs_qcom_phy() of generic phy, we can extract the - * common phy structure (struct ufs_qcom_phy) out of it - * regardless of the relevant specific phy. - */ -struct ufs_qcom_phy_qmp_14nm { - struct ufs_qcom_phy common_cfg; -}; - -static struct ufs_qcom_phy_calibration phy_cal_table_rate_A[] = { - UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_CONFIG, 0x0e), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0xd7), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CLK_SELECT, 0x30), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x06), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TIMER, 0x0a), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_HSCLK_SEL, 0x05), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV, 0x0a), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_EN, 0x01), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_CTRL, 0x10), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x20), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_EN, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_CFG, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER1, 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x14), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE0, 0x82), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE0, 0x0b), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE0, 0x28), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE0, 0x02), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE0, 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE1, 0x98), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE1, 0x0b), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE1, 0x16), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE1, 0x28), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE1, 0xd6), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE1, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE1, 0x32), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE1, 0x00), - - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN, 0x45), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE, 0x02), - - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_LVL, 0x24), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL, 0x02), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_INTERFACE_MODE, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x18), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_BW, 0x5B), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x0F), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0E), -}; - -static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x54), -}; - -#endif diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c deleted file mode 100644 index 3e9d8b71e995..000000000000 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c +++ /dev/null @@ -1,226 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - */ - -#include "phy-qcom-ufs-qmp-20nm.h" - -#define UFS_PHY_NAME "ufs_phy_qmp_20nm" - -static -int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, - bool is_rate_B) -{ - struct ufs_qcom_phy_calibration *tbl_A, *tbl_B; - int tbl_size_A, tbl_size_B; - u8 major = ufs_qcom_phy->host_ctrl_rev_major; - u16 minor = ufs_qcom_phy->host_ctrl_rev_minor; - u16 step = ufs_qcom_phy->host_ctrl_rev_step; - int err; - - if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) { - tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_2_0); - tbl_A = phy_cal_table_rate_A_1_2_0; - } else if ((major == 0x1) && (minor == 0x003) && (step == 0x0000)) { - tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_3_0); - tbl_A = phy_cal_table_rate_A_1_3_0; - } else { - dev_err(ufs_qcom_phy->dev, "%s: Unknown UFS-PHY version, no calibration values\n", - __func__); - err = -ENODEV; - goto out; - } - - tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B); - tbl_B = phy_cal_table_rate_B; - - err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A, - tbl_B, tbl_size_B, is_rate_B); - - if (err) - dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n", - __func__, err); - -out: - return err; -} - -static -void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common) -{ - phy_common->quirks = - UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; -} - -static -int ufs_qcom_phy_qmp_20nm_set_mode(struct phy *generic_phy, - enum phy_mode mode, int submode) -{ - struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - - phy_common->mode = PHY_MODE_INVALID; - - if (mode > 0) - phy_common->mode = mode; - - return 0; -} - -static -void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val) -{ - bool hibern8_exit_after_pwr_collapse = phy->quirks & - UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; - - if (val) { - writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); - /* - * Before any transactions involving PHY, ensure PHY knows - * that it's analog rail is powered ON. - */ - mb(); - - if (hibern8_exit_after_pwr_collapse) { - /* - * Give atleast 1us delay after restoring PHY analog - * power. - */ - usleep_range(1, 2); - writel_relaxed(0x0A, phy->mmio + - QSERDES_COM_SYSCLK_EN_SEL_TXBAND); - writel_relaxed(0x08, phy->mmio + - QSERDES_COM_SYSCLK_EN_SEL_TXBAND); - /* - * Make sure workaround is deactivated before proceeding - * with normal PHY operations. - */ - mb(); - } - } else { - if (hibern8_exit_after_pwr_collapse) { - writel_relaxed(0x0A, phy->mmio + - QSERDES_COM_SYSCLK_EN_SEL_TXBAND); - writel_relaxed(0x02, phy->mmio + - QSERDES_COM_SYSCLK_EN_SEL_TXBAND); - /* - * Make sure that above workaround is activated before - * PHY analog power collapse. - */ - mb(); - } - - writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); - /* - * ensure that PHY knows its PHY analog rail is going - * to be powered down - */ - mb(); - } -} - -static -void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val) -{ - writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK, - phy->mmio + UFS_PHY_TX_LANE_ENABLE); - mb(); -} - -static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy) -{ - u32 tmp; - - tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START); - tmp &= ~MASK_SERDES_START; - tmp |= (1 << OFFSET_SERDES_START); - writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START); - mb(); -} - -static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) -{ - int err = 0; - u32 val; - - err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS, - val, (val & MASK_PCS_READY), 10, 1000000); - if (err) - dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n", - __func__, err); - return err; -} - -static const struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = { - .power_on = ufs_qcom_phy_power_on, - .power_off = ufs_qcom_phy_power_off, - .set_mode = ufs_qcom_phy_qmp_20nm_set_mode, - .owner = THIS_MODULE, -}; - -static struct ufs_qcom_phy_specific_ops phy_20nm_ops = { - .calibrate = ufs_qcom_phy_qmp_20nm_phy_calibrate, - .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes, - .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready, - .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable, - .power_control = ufs_qcom_phy_qmp_20nm_power_control, -}; - -static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev) -{ - struct device *dev = &pdev->dev; - struct phy *generic_phy; - struct ufs_qcom_phy_qmp_20nm *phy; - struct ufs_qcom_phy *phy_common; - int err = 0; - - phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); - if (!phy) { - err = -ENOMEM; - goto out; - } - phy_common = &phy->common_cfg; - - generic_phy = ufs_qcom_phy_generic_probe(pdev, phy_common, - &ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops); - - if (!generic_phy) { - err = -EIO; - goto out; - } - - err = ufs_qcom_phy_init_clks(phy_common); - if (err) - goto out; - - err = ufs_qcom_phy_init_vregulators(phy_common); - if (err) - goto out; - - ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common); - - phy_set_drvdata(generic_phy, phy); - - strlcpy(phy_common->name, UFS_PHY_NAME, sizeof(phy_common->name)); - -out: - return err; -} - -static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = { - {.compatible = "qcom,ufs-phy-qmp-20nm"}, - {}, -}; -MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match); - -static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = { - .probe = ufs_qcom_phy_qmp_20nm_probe, - .driver = { - .of_match_table = ufs_qcom_phy_qmp_20nm_of_match, - .name = "ufs_qcom_phy_qmp_20nm", - }, -}; - -module_platform_driver(ufs_qcom_phy_qmp_20nm_driver); - -MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm"); -MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h deleted file mode 100644 index 8ce79f524eed..000000000000 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h +++ /dev/null @@ -1,226 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-only */ -/* - * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - */ - -#ifndef UFS_QCOM_PHY_QMP_20NM_H_ -#define UFS_QCOM_PHY_QMP_20NM_H_ - -#include "phy-qcom-ufs-i.h" - -/* QCOM UFS PHY control registers */ - -#define COM_OFF(x) (0x000 + x) -#define PHY_OFF(x) (0xC00 + x) -#define TX_OFF(n, x) (0x400 + (0x400 * n) + x) -#define RX_OFF(n, x) (0x600 + (0x400 * n) + x) - -/* UFS PHY PLL block registers */ -#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0) -#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04) -#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14) -#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24) -#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28) -#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x30) -#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34) -#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38) -#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C) -#define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48) -#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C) -#define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50) -#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90) -#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94) -#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98) -#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C) -#define QSERDES_COM_BGTC COM_OFF(0xA0) -#define QSERDES_COM_DEC_START1 COM_OFF(0xAC) -#define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0) -#define QSERDES_COM_RES_CODE_UP_OFFSET COM_OFF(0xD8) -#define QSERDES_COM_RES_CODE_DN_OFFSET COM_OFF(0xDC) -#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100) -#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104) -#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108) -#define QSERDES_COM_DEC_START2 COM_OFF(0x10C) -#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110) -#define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114) -#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118) - -/* TX LANE n (0, 1) registers */ -#define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08) -#define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C) -#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54) - -/* RX LANE n (0, 1) registers */ -#define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0) -#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8) -#define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8) -#define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC) -#define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0) -#define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4) -#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC) -#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC) -#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100) - -/* UFS PHY registers */ -#define UFS_PHY_PHY_START PHY_OFF(0x00) -#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4) -#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44) -#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08) -#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C) -#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10) -#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14) -#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34) -#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38) -#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C) -#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40) -#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68) -#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28) -#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C) -#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48) -#define UFS_PHY_PLL_CNTL PHY_OFF(0x50) -#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54) -#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C) -#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58) -#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60) -#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64) -#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C) -#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4) -#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0) -#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8) -#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4) -#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC) -#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8) -#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC) -#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100) -#define UFS_PHY_RX_SIGDET_CTRL3 PHY_OFF(0x14c) -#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160) -#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7) -#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6) -#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5) -#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4) -#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3) -#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2) -#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1) -#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0) -#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164) -#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168) -#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C) -#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170) -#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174) - -#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3 - -/* - * This structure represents the 20nm specific phy. - * common_cfg MUST remain the first field in this structure - * in case extra fields are added. This way, when calling - * get_ufs_qcom_phy() of generic phy, we can extract the - * common phy structure (struct ufs_qcom_phy) out of it - * regardless of the relevant specific phy. - */ -struct ufs_qcom_phy_qmp_20nm { - struct ufs_qcom_phy common_cfg; -}; - -static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_2_0[] = { - UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), - UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3), -}; - -static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_3_0[] = { - UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), - UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x2b), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x38), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x3c), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_UP_OFFSET, 0x02), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_DN_OFFSET, 0x02), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x40), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3), -}; - -static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65), - UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e), -}; - -#endif diff --git a/drivers/phy/qualcomm/phy-qcom-ufs.c b/drivers/phy/qualcomm/phy-qcom-ufs.c deleted file mode 100644 index 763c8d396af1..000000000000 --- a/drivers/phy/qualcomm/phy-qcom-ufs.c +++ /dev/null @@ -1,648 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - */ - -#include "phy-qcom-ufs-i.h" - -#define MAX_PROP_NAME 32 -#define VDDA_PHY_MIN_UV 1000000 -#define VDDA_PHY_MAX_UV 1000000 -#define VDDA_PLL_MIN_UV 1800000 -#define VDDA_PLL_MAX_UV 1800000 -#define VDDP_REF_CLK_MIN_UV 1200000 -#define VDDP_REF_CLK_MAX_UV 1200000 - -int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, - struct ufs_qcom_phy_calibration *tbl_A, - int tbl_size_A, - struct ufs_qcom_phy_calibration *tbl_B, - int tbl_size_B, bool is_rate_B) -{ - int i; - int ret = 0; - - if (!tbl_A) { - dev_err(ufs_qcom_phy->dev, "%s: tbl_A is NULL", __func__); - ret = EINVAL; - goto out; - } - - for (i = 0; i < tbl_size_A; i++) - writel_relaxed(tbl_A[i].cfg_value, - ufs_qcom_phy->mmio + tbl_A[i].reg_offset); - - /* - * In case we would like to work in rate B, we need - * to override a registers that were configured in rate A table - * with registers of rate B table. - * table. - */ - if (is_rate_B) { - if (!tbl_B) { - dev_err(ufs_qcom_phy->dev, "%s: tbl_B is NULL", - __func__); - ret = EINVAL; - goto out; - } - - for (i = 0; i < tbl_size_B; i++) - writel_relaxed(tbl_B[i].cfg_value, - ufs_qcom_phy->mmio + tbl_B[i].reg_offset); - } - - /* flush buffered writes */ - mb(); - -out: - return ret; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_calibrate); - -/* - * This assumes the embedded phy structure inside generic_phy is of type - * struct ufs_qcom_phy. In order to function properly it's crucial - * to keep the embedded struct "struct ufs_qcom_phy common_cfg" - * as the first inside generic_phy. - */ -struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy) -{ - return (struct ufs_qcom_phy *)phy_get_drvdata(generic_phy); -} -EXPORT_SYMBOL_GPL(get_ufs_qcom_phy); - -static -int ufs_qcom_phy_base_init(struct platform_device *pdev, - struct ufs_qcom_phy *phy_common) -{ - struct device *dev = &pdev->dev; - struct resource *res; - int err = 0; - - res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy_mem"); - phy_common->mmio = devm_ioremap_resource(dev, res); - if (IS_ERR((void const *)phy_common->mmio)) { - err = PTR_ERR((void const *)phy_common->mmio); - phy_common->mmio = NULL; - dev_err(dev, "%s: ioremap for phy_mem resource failed %d\n", - __func__, err); - return err; - } - - /* "dev_ref_clk_ctrl_mem" is optional resource */ - res = platform_get_resource_byname(pdev, IORESOURCE_MEM, - "dev_ref_clk_ctrl_mem"); - phy_common->dev_ref_clk_ctrl_mmio = devm_ioremap_resource(dev, res); - if (IS_ERR((void const *)phy_common->dev_ref_clk_ctrl_mmio)) - phy_common->dev_ref_clk_ctrl_mmio = NULL; - - return 0; -} - -struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev, - struct ufs_qcom_phy *common_cfg, - const struct phy_ops *ufs_qcom_phy_gen_ops, - struct ufs_qcom_phy_specific_ops *phy_spec_ops) -{ - int err; - struct device *dev = &pdev->dev; - struct phy *generic_phy = NULL; - struct phy_provider *phy_provider; - - err = ufs_qcom_phy_base_init(pdev, common_cfg); - if (err) { - dev_err(dev, "%s: phy base init failed %d\n", __func__, err); - goto out; - } - - phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); - if (IS_ERR(phy_provider)) { - err = PTR_ERR(phy_provider); - dev_err(dev, "%s: failed to register phy %d\n", __func__, err); - goto out; - } - - generic_phy = devm_phy_create(dev, NULL, ufs_qcom_phy_gen_ops); - if (IS_ERR(generic_phy)) { - err = PTR_ERR(generic_phy); - dev_err(dev, "%s: failed to create phy %d\n", __func__, err); - generic_phy = NULL; - goto out; - } - - common_cfg->phy_spec_ops = phy_spec_ops; - common_cfg->dev = dev; - -out: - return generic_phy; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_generic_probe); - -static int ufs_qcom_phy_get_reset(struct ufs_qcom_phy *phy_common) -{ - struct reset_control *reset; - - if (phy_common->ufs_reset) - return 0; - - reset = devm_reset_control_get_exclusive_by_index(phy_common->dev, 0); - if (IS_ERR(reset)) - return PTR_ERR(reset); - - phy_common->ufs_reset = reset; - return 0; -} - -static int __ufs_qcom_phy_clk_get(struct device *dev, - const char *name, struct clk **clk_out, bool err_print) -{ - struct clk *clk; - int err = 0; - - clk = devm_clk_get(dev, name); - if (IS_ERR(clk)) { - err = PTR_ERR(clk); - if (err_print) - dev_err(dev, "failed to get %s err %d", name, err); - } else { - *clk_out = clk; - } - - return err; -} - -static int ufs_qcom_phy_clk_get(struct device *dev, - const char *name, struct clk **clk_out) -{ - return __ufs_qcom_phy_clk_get(dev, name, clk_out, true); -} - -int ufs_qcom_phy_init_clks(struct ufs_qcom_phy *phy_common) -{ - int err; - - if (of_device_is_compatible(phy_common->dev->of_node, - "qcom,msm8996-ufs-phy-qmp-14nm")) - goto skip_txrx_clk; - - err = ufs_qcom_phy_clk_get(phy_common->dev, "tx_iface_clk", - &phy_common->tx_iface_clk); - if (err) - goto out; - - err = ufs_qcom_phy_clk_get(phy_common->dev, "rx_iface_clk", - &phy_common->rx_iface_clk); - if (err) - goto out; - -skip_txrx_clk: - err = ufs_qcom_phy_clk_get(phy_common->dev, "ref_clk_src", - &phy_common->ref_clk_src); - if (err) - goto out; - - /* - * "ref_clk_parent" is optional hence don't abort init if it's not - * found. - */ - __ufs_qcom_phy_clk_get(phy_common->dev, "ref_clk_parent", - &phy_common->ref_clk_parent, false); - - err = ufs_qcom_phy_clk_get(phy_common->dev, "ref_clk", - &phy_common->ref_clk); - -out: - return err; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_init_clks); - -static int ufs_qcom_phy_init_vreg(struct device *dev, - struct ufs_qcom_phy_vreg *vreg, - const char *name) -{ - int err = 0; - - char prop_name[MAX_PROP_NAME]; - - vreg->name = name; - vreg->reg = devm_regulator_get(dev, name); - if (IS_ERR(vreg->reg)) { - err = PTR_ERR(vreg->reg); - dev_err(dev, "failed to get %s, %d\n", name, err); - goto out; - } - - if (dev->of_node) { - snprintf(prop_name, MAX_PROP_NAME, "%s-max-microamp", name); - err = of_property_read_u32(dev->of_node, - prop_name, &vreg->max_uA); - if (err && err != -EINVAL) { - dev_err(dev, "%s: failed to read %s\n", - __func__, prop_name); - goto out; - } else if (err == -EINVAL || !vreg->max_uA) { - if (regulator_count_voltages(vreg->reg) > 0) { - dev_err(dev, "%s: %s is mandatory\n", - __func__, prop_name); - goto out; - } - err = 0; - } - } - - if (!strcmp(name, "vdda-pll")) { - vreg->max_uV = VDDA_PLL_MAX_UV; - vreg->min_uV = VDDA_PLL_MIN_UV; - } else if (!strcmp(name, "vdda-phy")) { - vreg->max_uV = VDDA_PHY_MAX_UV; - vreg->min_uV = VDDA_PHY_MIN_UV; - } else if (!strcmp(name, "vddp-ref-clk")) { - vreg->max_uV = VDDP_REF_CLK_MAX_UV; - vreg->min_uV = VDDP_REF_CLK_MIN_UV; - } - -out: - return err; -} - -int ufs_qcom_phy_init_vregulators(struct ufs_qcom_phy *phy_common) -{ - int err; - - err = ufs_qcom_phy_init_vreg(phy_common->dev, &phy_common->vdda_pll, - "vdda-pll"); - if (err) - goto out; - - err = ufs_qcom_phy_init_vreg(phy_common->dev, &phy_common->vdda_phy, - "vdda-phy"); - - if (err) - goto out; - - err = ufs_qcom_phy_init_vreg(phy_common->dev, &phy_common->vddp_ref_clk, - "vddp-ref-clk"); - -out: - return err; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_init_vregulators); - -static int ufs_qcom_phy_cfg_vreg(struct device *dev, - struct ufs_qcom_phy_vreg *vreg, bool on) -{ - int ret = 0; - struct regulator *reg = vreg->reg; - const char *name = vreg->name; - int min_uV; - int uA_load; - - if (regulator_count_voltages(reg) > 0) { - min_uV = on ? vreg->min_uV : 0; - ret = regulator_set_voltage(reg, min_uV, vreg->max_uV); - if (ret) { - dev_err(dev, "%s: %s set voltage failed, err=%d\n", - __func__, name, ret); - goto out; - } - uA_load = on ? vreg->max_uA : 0; - ret = regulator_set_load(reg, uA_load); - if (ret >= 0) { - /* - * regulator_set_load() returns new regulator - * mode upon success. - */ - ret = 0; - } else { - dev_err(dev, "%s: %s set optimum mode(uA_load=%d) failed, err=%d\n", - __func__, name, uA_load, ret); - goto out; - } - } -out: - return ret; -} - -static int ufs_qcom_phy_enable_vreg(struct device *dev, - struct ufs_qcom_phy_vreg *vreg) -{ - int ret = 0; - - if (!vreg || vreg->enabled) - goto out; - - ret = ufs_qcom_phy_cfg_vreg(dev, vreg, true); - if (ret) { - dev_err(dev, "%s: ufs_qcom_phy_cfg_vreg() failed, err=%d\n", - __func__, ret); - goto out; - } - - ret = regulator_enable(vreg->reg); - if (ret) { - dev_err(dev, "%s: enable failed, err=%d\n", - __func__, ret); - goto out; - } - - vreg->enabled = true; -out: - return ret; -} - -static int ufs_qcom_phy_enable_ref_clk(struct ufs_qcom_phy *phy) -{ - int ret = 0; - - if (phy->is_ref_clk_enabled) - goto out; - - /* - * reference clock is propagated in a daisy-chained manner from - * source to phy, so ungate them at each stage. - */ - ret = clk_prepare_enable(phy->ref_clk_src); - if (ret) { - dev_err(phy->dev, "%s: ref_clk_src enable failed %d\n", - __func__, ret); - goto out; - } - - /* - * "ref_clk_parent" is optional clock hence make sure that clk reference - * is available before trying to enable the clock. - */ - if (phy->ref_clk_parent) { - ret = clk_prepare_enable(phy->ref_clk_parent); - if (ret) { - dev_err(phy->dev, "%s: ref_clk_parent enable failed %d\n", - __func__, ret); - goto out_disable_src; - } - } - - ret = clk_prepare_enable(phy->ref_clk); - if (ret) { - dev_err(phy->dev, "%s: ref_clk enable failed %d\n", - __func__, ret); - goto out_disable_parent; - } - - phy->is_ref_clk_enabled = true; - goto out; - -out_disable_parent: - if (phy->ref_clk_parent) - clk_disable_unprepare(phy->ref_clk_parent); -out_disable_src: - clk_disable_unprepare(phy->ref_clk_src); -out: - return ret; -} - -static int ufs_qcom_phy_disable_vreg(struct device *dev, - struct ufs_qcom_phy_vreg *vreg) -{ - int ret = 0; - - if (!vreg || !vreg->enabled) - goto out; - - ret = regulator_disable(vreg->reg); - - if (!ret) { - /* ignore errors on applying disable config */ - ufs_qcom_phy_cfg_vreg(dev, vreg, false); - vreg->enabled = false; - } else { - dev_err(dev, "%s: %s disable failed, err=%d\n", - __func__, vreg->name, ret); - } -out: - return ret; -} - -static void ufs_qcom_phy_disable_ref_clk(struct ufs_qcom_phy *phy) -{ - if (phy->is_ref_clk_enabled) { - clk_disable_unprepare(phy->ref_clk); - /* - * "ref_clk_parent" is optional clock hence make sure that clk - * reference is available before trying to disable the clock. - */ - if (phy->ref_clk_parent) - clk_disable_unprepare(phy->ref_clk_parent); - clk_disable_unprepare(phy->ref_clk_src); - phy->is_ref_clk_enabled = false; - } -} - -/* Turn ON M-PHY RMMI interface clocks */ -static int ufs_qcom_phy_enable_iface_clk(struct ufs_qcom_phy *phy) -{ - int ret = 0; - - if (phy->is_iface_clk_enabled) - goto out; - - ret = clk_prepare_enable(phy->tx_iface_clk); - if (ret) { - dev_err(phy->dev, "%s: tx_iface_clk enable failed %d\n", - __func__, ret); - goto out; - } - ret = clk_prepare_enable(phy->rx_iface_clk); - if (ret) { - clk_disable_unprepare(phy->tx_iface_clk); - dev_err(phy->dev, "%s: rx_iface_clk enable failed %d. disabling also tx_iface_clk\n", - __func__, ret); - goto out; - } - phy->is_iface_clk_enabled = true; - -out: - return ret; -} - -/* Turn OFF M-PHY RMMI interface clocks */ -static void ufs_qcom_phy_disable_iface_clk(struct ufs_qcom_phy *phy) -{ - if (phy->is_iface_clk_enabled) { - clk_disable_unprepare(phy->tx_iface_clk); - clk_disable_unprepare(phy->rx_iface_clk); - phy->is_iface_clk_enabled = false; - } -} - -static int ufs_qcom_phy_start_serdes(struct ufs_qcom_phy *ufs_qcom_phy) -{ - int ret = 0; - - if (!ufs_qcom_phy->phy_spec_ops->start_serdes) { - dev_err(ufs_qcom_phy->dev, "%s: start_serdes() callback is not supported\n", - __func__); - ret = -ENOTSUPP; - } else { - ufs_qcom_phy->phy_spec_ops->start_serdes(ufs_qcom_phy); - } - - return ret; -} - -int ufs_qcom_phy_set_tx_lane_enable(struct phy *generic_phy, u32 tx_lanes) -{ - struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); - int ret = 0; - - if (!ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable) { - dev_err(ufs_qcom_phy->dev, "%s: set_tx_lane_enable() callback is not supported\n", - __func__); - ret = -ENOTSUPP; - } else { - ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable(ufs_qcom_phy, - tx_lanes); - } - - return ret; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_set_tx_lane_enable); - -void ufs_qcom_phy_save_controller_version(struct phy *generic_phy, - u8 major, u16 minor, u16 step) -{ - struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); - - ufs_qcom_phy->host_ctrl_rev_major = major; - ufs_qcom_phy->host_ctrl_rev_minor = minor; - ufs_qcom_phy->host_ctrl_rev_step = step; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_save_controller_version); - -static int ufs_qcom_phy_is_pcs_ready(struct ufs_qcom_phy *ufs_qcom_phy) -{ - if (!ufs_qcom_phy->phy_spec_ops->is_physical_coding_sublayer_ready) { - dev_err(ufs_qcom_phy->dev, "%s: is_physical_coding_sublayer_ready() callback is not supported\n", - __func__); - return -ENOTSUPP; - } - - return ufs_qcom_phy->phy_spec_ops-> - is_physical_coding_sublayer_ready(ufs_qcom_phy); -} - -int ufs_qcom_phy_power_on(struct phy *generic_phy) -{ - struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - struct device *dev = phy_common->dev; - bool is_rate_B = false; - int err; - - err = ufs_qcom_phy_get_reset(phy_common); - if (err) - return err; - - err = reset_control_assert(phy_common->ufs_reset); - if (err) - return err; - - if (phy_common->mode == PHY_MODE_UFS_HS_B) - is_rate_B = true; - - err = phy_common->phy_spec_ops->calibrate(phy_common, is_rate_B); - if (err) - return err; - - err = reset_control_deassert(phy_common->ufs_reset); - if (err) { - dev_err(dev, "Failed to assert UFS PHY reset"); - return err; - } - - err = ufs_qcom_phy_start_serdes(phy_common); - if (err) - return err; - - err = ufs_qcom_phy_is_pcs_ready(phy_common); - if (err) - return err; - - err = ufs_qcom_phy_enable_vreg(dev, &phy_common->vdda_phy); - if (err) { - dev_err(dev, "%s enable vdda_phy failed, err=%d\n", - __func__, err); - goto out; - } - - phy_common->phy_spec_ops->power_control(phy_common, true); - - /* vdda_pll also enables ref clock LDOs so enable it first */ - err = ufs_qcom_phy_enable_vreg(dev, &phy_common->vdda_pll); - if (err) { - dev_err(dev, "%s enable vdda_pll failed, err=%d\n", - __func__, err); - goto out_disable_phy; - } - - err = ufs_qcom_phy_enable_iface_clk(phy_common); - if (err) { - dev_err(dev, "%s enable phy iface clock failed, err=%d\n", - __func__, err); - goto out_disable_pll; - } - - err = ufs_qcom_phy_enable_ref_clk(phy_common); - if (err) { - dev_err(dev, "%s enable phy ref clock failed, err=%d\n", - __func__, err); - goto out_disable_iface_clk; - } - - /* enable device PHY ref_clk pad rail */ - if (phy_common->vddp_ref_clk.reg) { - err = ufs_qcom_phy_enable_vreg(dev, - &phy_common->vddp_ref_clk); - if (err) { - dev_err(dev, "%s enable vddp_ref_clk failed, err=%d\n", - __func__, err); - goto out_disable_ref_clk; - } - } - - goto out; - -out_disable_ref_clk: - ufs_qcom_phy_disable_ref_clk(phy_common); -out_disable_iface_clk: - ufs_qcom_phy_disable_iface_clk(phy_common); -out_disable_pll: - ufs_qcom_phy_disable_vreg(dev, &phy_common->vdda_pll); -out_disable_phy: - ufs_qcom_phy_disable_vreg(dev, &phy_common->vdda_phy); -out: - return err; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_power_on); - -int ufs_qcom_phy_power_off(struct phy *generic_phy) -{ - struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - - phy_common->phy_spec_ops->power_control(phy_common, false); - - if (phy_common->vddp_ref_clk.reg) - ufs_qcom_phy_disable_vreg(phy_common->dev, - &phy_common->vddp_ref_clk); - ufs_qcom_phy_disable_ref_clk(phy_common); - ufs_qcom_phy_disable_iface_clk(phy_common); - - ufs_qcom_phy_disable_vreg(phy_common->dev, &phy_common->vdda_pll); - ufs_qcom_phy_disable_vreg(phy_common->dev, &phy_common->vdda_phy); - reset_control_assert(phy_common->ufs_reset); - return 0; -} -EXPORT_SYMBOL_GPL(ufs_qcom_phy_power_off); - -MODULE_AUTHOR("Yaniv Gardi "); -MODULE_AUTHOR("Vivek Gautam "); -MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY"); -MODULE_LICENSE("GPL v2"); -- cgit v1.2.3