From 9425183d177aa4a2f09d01a74925124f0778b595 Mon Sep 17 00:00:00 2001 From: Lu Baolu Date: Mon, 23 Mar 2015 18:27:41 +0200 Subject: usb: xhci: handle Config Error Change (CEC) in xhci driver Linux xHCI driver doesn't report and handle port cofig error change. If Port Configure Error for root hub port occurs, CEC bit in PORTSC would be set by xHC and remains 1. This happends when the root port fails to configure its link partner, e.g. the port fails to exchange port capabilities information using Port Capability LMPs. Then the Port Status Change Events will be blocked until all status change bits(CEC is one of the change bits) are cleared('0') (refer to xHCI spec 4.19.2). Otherwise, the port status change event for this root port will not be generated anymore, then root port would look like dead for user and can't be recovered until a Host Controller Reset(HCRST). This patch is to check CEC bit in PORTSC in xhci_get_port_status() and set a Config Error in the return status if CEC is set. This will cause a ClearPortFeature request, where CEC bit is cleared in xhci_clear_port_change_bit(). [The commit log is based on initial Marvell patch posted at http://marc.info/?l=linux-kernel&m=142323612321434&w=2] Reported-by: Gregory CLEMENT Signed-off-by: Lu Baolu Cc: stable # v3.2+ Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hub.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index a7865c4b0498..0827d7c96527 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -387,6 +387,10 @@ static void xhci_clear_port_change_bit(struct xhci_hcd *xhci, u16 wValue, status = PORT_PLC; port_change_bit = "link state"; break; + case USB_PORT_FEAT_C_PORT_CONFIG_ERROR: + status = PORT_CEC; + port_change_bit = "config error"; + break; default: /* Should never happen */ return; @@ -588,6 +592,8 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd, status |= USB_PORT_STAT_C_LINK_STATE << 16; if ((raw_port_status & PORT_WRC)) status |= USB_PORT_STAT_C_BH_RESET << 16; + if ((raw_port_status & PORT_CEC)) + status |= USB_PORT_STAT_C_CONFIG_ERROR << 16; } if (hcd->speed != HCD_USB3) { @@ -1005,6 +1011,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, case USB_PORT_FEAT_C_OVER_CURRENT: case USB_PORT_FEAT_C_ENABLE: case USB_PORT_FEAT_C_PORT_LINK_STATE: + case USB_PORT_FEAT_C_PORT_CONFIG_ERROR: xhci_clear_port_change_bit(xhci, wValue, wIndex, port_array[wIndex], temp); break; @@ -1069,7 +1076,7 @@ int xhci_hub_status_data(struct usb_hcd *hcd, char *buf) */ status = bus_state->resuming_ports; - mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC; + mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC | PORT_CEC; spin_lock_irqsave(&xhci->lock, flags); /* For each port, did anything change? If so, set that bit in buf. */ -- cgit v1.2.3