# Select 32 or 64 bit config 64BIT bool "64-bit kernel" if ARCH = "x86" default ARCH != "i386" ---help--- Say yes to build a 64-bit kernel - formerly known as x86_64 Say no to build a 32-bit kernel - formerly known as i386 config X86_32 def_bool y depends on !64BIT select CLKSRC_I8253 select HAVE_UID16 config X86_64 def_bool y depends on 64BIT select X86_DEV_DMA_OPS select ARCH_USE_CMPXCHG_LOCKREF ### Arch settings config X86 def_bool y select ARCH_HAS_DEBUG_STRICT_USER_COPY_CHECKS select ARCH_MIGHT_HAVE_PC_PARPORT select HAVE_AOUT if X86_32 select HAVE_UNSTABLE_SCHED_CLOCK select ARCH_SUPPORTS_NUMA_BALANCING select ARCH_SUPPORTS_INT128 if X86_64 select ARCH_WANTS_PROT_NUMA_PROT_NONE select HAVE_IDE select HAVE_OPROFILE select HAVE_PCSPKR_PLATFORM select HAVE_PERF_EVENTS select HAVE_IOREMAP_PROT select HAVE_KPROBES select HAVE_MEMBLOCK select HAVE_MEMBLOCK_NODE_MAP select ARCH_DISCARD_MEMBLOCK select ARCH_WANT_OPTIONAL_GPIOLIB select ARCH_WANT_FRAME_POINTERS select HAVE_DMA_ATTRS select HAVE_DMA_CONTIGUOUS if !SWIOTLB select HAVE_KRETPROBES select HAVE_OPTPROBES select HAVE_KPROBES_ON_FTRACE select HAVE_FTRACE_MCOUNT_RECORD select HAVE_FENTRY if X86_64 select HAVE_C_RECORDMCOUNT select HAVE_DYNAMIC_FTRACE select HAVE_DYNAMIC_FTRACE_WITH_REGS select HAVE_FUNCTION_TRACER select HAVE_FUNCTION_GRAPH_TRACER select HAVE_FUNCTION_GRAPH_FP_TEST select HAVE_FUNCTION_TRACE_MCOUNT_TEST select HAVE_SYSCALL_TRACEPOINTS select SYSCTL_EXCEPTION_TRACE select HAVE_KVM select HAVE_ARCH_KGDB select HAVE_ARCH_TRACEHOOK select HAVE_GENERIC_DMA_COHERENT if X86_32 select HAVE_EFFICIENT_UNALIGNED_ACCESS select USER_STACKTRACE_SUPPORT select HAVE_REGS_AND_STACK_ACCESS_API select HAVE_DMA_API_DEBUG select HAVE_KERNEL_GZIP select HAVE_KERNEL_BZIP2 select HAVE_KERNEL_LZMA select HAVE_KERNEL_XZ select HAVE_KERNEL_LZO select HAVE_KERNEL_LZ4 select HAVE_HW_BREAKPOINT select HAVE_MIXED_BREAKPOINTS_REGS select PERF_EVENTS select HAVE_PERF_EVENTS_NMI select HAVE_PERF_REGS select HAVE_PERF_USER_STACK_DUMP select HAVE_DEBUG_KMEMLEAK select ANON_INODES select HAVE_ALIGNED_STRUCT_PAGE if SLUB select HAVE_CMPXCHG_LOCAL select HAVE_CMPXCHG_DOUBLE select HAVE_ARCH_KMEMCHECK select HAVE_USER_RETURN_NOTIFIER select ARCH_BINFMT_ELF_RANDOMIZE_PIE select HAVE_ARCH_JUMP_LABEL select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select SPARSE_IRQ select GENERIC_FIND_FIRST_BIT select GENERIC_IRQ_PROBE select GENERIC_PENDING_IRQ if SMP select GENERIC_IRQ_SHOW select GENERIC_CLOCKEVENTS_MIN_ADJUST select IRQ_FORCED_THREADING select HAVE_BPF_JIT if X86_64 select HAVE_ARCH_TRANSPARENT_HUGEPAGE select CLKEVT_I8253 select ARCH_HAVE_NMI_SAFE_CMPXCHG select GENERIC_IOMAP select DCACHE_WORD_ACCESS select GENERIC_SMP_IDLE_THREAD select ARCH_WANT_IPC_PARSE_VERSION if X86_32 select HAVE_ARCH_SECCOMP_FILTER select BUILDTIME_EXTABLE_SORT select GENERIC_CMOS_UPDATE select HAVE_ARCH_SOFT_DIRTY select CLOCKSOURCE_WATCHDOG select GENERIC_CLOCKEVENTS select ARCH_CLOCKSOURCE_DATA if X86_64 select GENERIC_CLOCKEVENTS_BROADCAST if X86_64 || (X86_32 && X86_LOCAL_APIC) select GENERIC_TIME_VSYSCALL if X86_64 select KTIME_SCALAR if X86_32 select GENERIC_STRNCPY_FROM_USER select GENERIC_STRNLEN_USER select HAVE_CONTEXT_TRACKING if X86_64 select HAVE_IRQ_TIME_ACCOUNTING select VIRT_TO_BUS select MODULES_USE_ELF_REL if X86_32 select MODULES_USE_ELF_RELA if X86_64 select CLONE_BACKWARDS if X86_32 select ARCH_USE_BUILTIN_BSWAP select OLD_SIGSUSPEND3 if X86_32 || IA32_EMULATION select OLD_SIGACTION if X86_32 select COMPAT_OLD_SIGACTION if IA32_EMULATION select RTC_LIB select HAVE_DEBUG_STACKOVERFLOW select HAVE_IRQ_EXIT_ON_IRQ_STACK if X86_64 select HAVE_CC_STACKPROTECTOR config INSTRUCTION_DECODER def_bool y depends on KPROBES || PERF_EVENTS || UPROBES config OUTPUT_FORMAT string default "elf32-i386" if X86_32 default "elf64-x86-64" if X86_64 config ARCH_DEFCONFIG string default "arch/x86/configs/i386_defconfig" if X86_32 default "arch/x86/configs/x86_64_defconfig" if X86_64 config LOCKDEP_SUPPORT def_bool y config STACKTRACE_SUPPORT def_bool y config HAVE_LATENCYTOP_SUPPORT def_bool y config MMU def_bool y config SBUS bool config NEED_DMA_MAP_STATE def_bool y depends on X86_64 || INTEL_IOMMU || DMA_API_DEBUG config NEED_SG_DMA_LENGTH def_bool y config GENERIC_ISA_DMA def_bool y depends on ISA_DMA_API config GENERIC_BUG def_bool y depends on BUG select GENERIC_BUG_RELATIVE_POINTERS if X86_64 config GENERIC_BUG_RELATIVE_POINTERS bool config GENERIC_HWEIGHT def_bool y config ARCH_MAY_HAVE_PC_FDC def_bool y depends on ISA_DMA_API config RWSEM_XCHGADD_ALGORITHM def_bool y config GENERIC_CALIBRATE_DELAY def_bool y config ARCH_HAS_CPU_RELAX def_bool y config ARCH_HAS_CACHE_LINE_SIZE def_bool y config ARCH_HAS_CPU_AUTOPROBE def_bool y config HAVE_SETUP_PER_CPU_AREA def_bool y config NEED_PER_CPU_EMBED_FIRST_CHUNK def_bool y config NEED_PER_CPU_PAGE_FIRST_CHUNK def_bool y config ARCH_HIBERNATION_POSSIBLE def_bool y config ARCH_SUSPEND_POSSIBLE def_bool y config ARCH_WANT_HUGE_PMD_SHARE def_bool y config ARCH_WANT_GENERAL_HUGETLB def_bool y config ZONE_DMA32 bool default X86_64 config AUDIT_ARCH bool default X86_64 config ARCH_SUPPORTS_OPTIMIZED_INLINING def_bool y config ARCH_SUPPORTS_DEBUG_PAGEALLOC def_bool y config HAVE_INTEL_TXT def_bool y depends on INTEL_IOMMU && ACPI config X86_32_SMP def_bool y depends on X86_32 && SMP config X86_64_SMP def_bool y depends on X86_64 && SMP config X86_HT def_bool y depends on SMP config X86_32_LAZY_GS def_bool y depends on X86_32 && !CC_STACKPROTECTOR config ARCH_HWEIGHT_CFLAGS string default "-fcall-saved-ecx -fcall-saved-edx" if X86_32 default "-fcall-saved-rdi -fcall-saved-rsi -fcall-saved-rdx -fcall-saved-rcx -fcall-saved-r8 -fcall-saved-r9 -fcall-saved-r10 -fcall-saved-r11" if X86_64 config ARCH_SUPPORTS_UPROBES def_bool y source "init/Kconfig" source "kernel/Kconfig.freezer" menu "Processor type and features" config ZONE_DMA bool "DMA memory allocation support" if EXPERT default y help DMA memory allocation support allows devices with less than 32-bit addressing to allocate within the first 16MB of address space. Disable if no such devices will be used. If unsure, say Y. config SMP bool "Symmetric multi-processing support" ---help--- This enables support for systems with more than one CPU. If you have a system with only one CPU, like most personal computers, say N. If you have a system with more than one CPU, say Y. If you say N here, the kernel will run on single and multiprocessor machines, but will use only one CPU of a multiprocessor machine. If you say Y here, the kernel will run on many, but not all, singleprocessor machines. On a singleprocessor machine, the kernel will run faster if you say N here. Note that if you say Y here and choose architecture "586" or "Pentium" under "Processor family", the kernel will not work on 486 architectures. Similarly, multiprocessor kernels for the "PPro" architecture may not work on all Pentium based boards. People using multiprocessor machines who say Y here should also say Y to "Enhanced Real Time Clock Support", below. The "Advanced Power Management" code will be disabled if you say Y here. See also , and the SMP-HOWTO available at . If you don't know what to do here, say N. config X86_X2APIC bool "Support x2apic" depends on X86_LOCAL_APIC && X86_64 && IRQ_REMAP ---help--- This enables x2apic support on CPUs that have this feature. This allows 32-bit apic IDs (so it can support very large systems), and accesses the local apic via MSRs not via mmio. If you don't know what to do here, say N. config X86_MPPARSE bool "Enable MPS table" if ACPI || SFI default y depends on X86_LOCAL_APIC ---help--- For old smp systems that do not have proper acpi support. Newer systems (esp with 64bit cpus) with acpi support, MADT and DSDT will override it config X86_BIGSMP bool "Support for big SMP systems with more than 8 CPUs" depends on X86_32 && SMP ---help--- This option is needed for the systems that have more than 8 CPUs config GOLDFISH def_bool y depends on X86_GOLDFISH if X86_32 config X86_EXTENDED_PLATFORM bool "Support for extended (non-PC) x86 platforms" default y ---help--- If you disable this option then the kernel will only support standard PC platforms. (which covers the vast majority of systems out there.) If you enable this option then you'll be able to select support for the following (non-PC) 32 bit x86 platforms: Goldfish (Android emulator) AMD Elan NUMAQ (IBM/Sequent) RDC R-321x SoC SGI 320/540 (Visual Workstation) STA2X11-based (e.g. Northville) Summit/EXA (IBM x440) Unisys ES7000 IA32 series Moorestown MID devices If you have one of these systems, or if you want to build a generic distribution kernel, say Y here - otherwise say N. endif if X86_64 config X86_EXTENDED_PLATFORM bool "Support for extended (non-PC) x86 platforms" default y ---help--- If you disable this option then the kernel will only support standard PC platforms. (which covers the vast majority of systems out there.) If you enable this option then you'll be able to select support for the following (non-PC) 64 bit x86 platforms: Numascale NumaChip ScaleMP vSMP SGI Ultraviolet If you have one of these systems, or if you want to build a generic distribution kernel, say Y here - otherwise say N. endif # This is an alphabetically sorted list of 64 bit extended platforms # Please maintain the alphabetic order if and when there are additions config X86_NUMACHIP bool "Numascale NumaChip" depends on X86_64 depends on X86_EXTENDED_PLATFORM depends on NUMA depends on SMP depends on X86_X2APIC depends on PCI_MMCONFIG ---help--- Adds support for Numascale NumaChip large-SMP systems. Needed to enable more than ~168 cores. If you don't have one of these, you should say N here. config X86_VSMP bool "ScaleMP vSMP" select HYPERVISOR_GUEST select PARAVIRT depends on X86_64 && PCI depends on X86_EXTENDED_PLATFORM depends on SMP ---help--- Support for ScaleMP vSMP systems. Say 'Y' here if this kernel is supposed to run on these EM64T-based machines. Only choose this option if you have one of these machines. config X86_UV bool "SGI Ultraviolet" depends on X86_64 depends on X86_EXTENDED_PLATFORM depends on NUMA depends on X86_X2APIC ---help--- This option is needed in order to support SGI Ultraviolet systems. If you don't have one of these, you should say N here. # Following is an alphabetically sorted list of 32 bit extended platforms # Please maintain the alphabetic order if and when there are additions config X86_GOLDFISH bool "Goldfish (Virtual Platform)" depends on X86_32 depends on X86_EXTENDED_PLATFORM ---help--- Enable support for the Goldfish virtual platform used primarily for Android development. Unless you are building for the Android Goldfish emulator say N here. config X86_INTEL_CE bool "CE4100 TV platform" depends on PCI depends on PCI_GODIRECT depends on X86_32 depends on X86_EXTENDED_PLATFORM select X86_REBOOTFIXUPS select OF select OF_EARLY_FLATTREE select IRQ_DOMAIN ---help--- Select for the Intel CE media processor (CE4100) SOC. This option compiles in support for the CE4100 SOC for settop boxes and media devices. config X86_INTEL_MID bool "Intel MID platform support" depends on X86_32 depends on X86_EXTENDED_PLATFORM depends on PCI depends on PCI_GOANY depends on X86_IO_APIC select SFI select I2C select DW_APB_TIMER select APB_TIMER select INTEL_SCU_IPC select MFD_INTEL_MSIC ---help--- Select to build a kernel capable of supporting Intel MID (Mobile Internet Device) platform systems which do not have the PCI legacy interfaces. If you are building for a PC class system say N here. Intel MID platforms are based on an Intel processor and chipset which consume less power than most of the x86 derivatives. config X86_INTEL_LPSS bool "Intel Low Power Subsystem Support" depends on ACPI select COMMON_CLK select PINCTRL ---help--- Select to build support for Intel Low Power Subsystem such as found on Intel Lynxpoint PCH. Selecting this option enables things like clock tree (common clock framework) and pincontrol which are needed by the LPSS peripheral drivers. config X86_RDC321X bool "RDC R-321x SoC" depends on X86_32 depends on X86_EXTENDED_PLATFORM select M486 select X86_REBOOTFIXUPS ---help--- This option is needed for RDC R-321x system-on-chip, also known as R-8610-(G). If you don't have one of these chips, you should say N here. config X86_32_NON_STANDARD bool "Support non-standard 32-bit SMP architectures" depends on X86_32 && SMP depends on X86_EXTENDED_PLATFORM ---help--- This option compiles in the NUMAQ, Summit, bigsmp, ES7000, STA2X11, default subarchitectures. It is intended for a generic binary kernel. If you select them all, kernel will probe it one by one and will fallback to default. # Alphabetically sorted list of Non standard 32 bit platforms config X86_NUMAQ bool "NUMAQ (IBM/Sequent)" depends on X86_32_NON_STANDARD depends on PCI select NUMA select X86_MPPARSE ---help--- This option is used for getting Linux to run on a NUMAQ (IBM/Sequent) NUMA multiquad box. This changes the way that processors are bootstrapped, and uses Clustered Logical APIC addressing mode instead of Flat Logical. You will need a new lynxer.elf file to flash your firmware with - send email to . config X86_SUPPORTS_MEMORY_FAILURE def_bool y # MCE code calls memory_failure(): depends on X86_MCE # On 32-bit this adds too big of NODES_SHIFT and we run out of page flags: depends on !X86_NUMAQ # On 32-bit SPARSEMEM adds too big of SECTIONS_WIDTH: depends on X86_64 || !SPARSEMEM select ARCH_SUPPORTS_MEMORY_FAILURE config X86_VISWS bool "SGI 320/540 (Visual Workstation)" depends on X86_32 && PCI && X86_MPPARSE && PCI_GODIRECT depends on X86_32_NON_STANDARD ---help--- The SGI Visual Workstation series is an IA32-based workstation based on SGI systems chips with some legacy PC hardware attached. Say Y here to create a kernel to run on the SGI 320 or 540. A kernel compiled for the Visual Workstation will run on general PCs as well. See for details. config STA2X11 bool "STA2X11 Companion Chip Support" depends on X86_32_NON_STANDARD && PCI select X86_DEV_DMA_OPS select X86_DMA_REMAP select SWIOTLB select MFD_STA2X11 select ARCH_REQUIRE_GPIOLIB default n ---help--- This adds support for boards based on the STA2X11 IO-Hub, a.k.a. "ConneXt". The chip is used in place of the standard PC chipset, so all "standard" peripherals are missing. If this option is selected the kernel will still be able to boot on standard PC machines. config X86_SUMMIT bool "Summit/EXA (IBM x440)" depends on X86_32_NON_STANDARD ---help--- This option is needed for IBM systems that use the Summit/EXA chipset. In particular, it is needed for the x440. config X86_ES7000 bool "Unisys ES7000 IA32 series" depends on X86_32_NON_STANDARD && X86_BIGSMP ---help--- Support for Unisys ES7000 systems. Say 'Y' here if this kernel is supposed to run on an IA32-based Unisys ES7000 system. config X86_32_IRIS tristate "Eurobraille/Iris poweroff module" depends on X86_32 ---help--- The Iris machines from EuroBraille do not have APM or ACPI support to shut themselves down properly. A special I/O sequence is needed to do so, which is what this module does at kernel shutdown. This is only for Iris machines from EuroBraille. If unused, say N. config SCHED_OMIT_FRAME_POINTER def_bool y prompt "Single-depth WCHAN output" depends on X86 ---help--- Calculate simpler /proc//wchan values. If this option is disabled then wchan values will recurse back to the caller function. This provides more accurate wchan values, at the expense of slightly more scheduling overhead. If in doubt, say "Y". menuconfig HYPERVISOR_GUEST bool "Linux guest support" ---help--- Say Y here to enable options for running Linux under various hyper- visors. This option enables basic hypervisor detection and platform setup. If you say N, all options in this submenu will be skipped and disabled, and Linux guest support won't be built in. if HYPERVISOR_GUEST config PARAVIRT bool "Enable paravirtualization code" ---help--- This changes the kernel so it can modify itself when it is run under a hypervisor, potentially improving performance significantly over full virtualization. However, when run without a hypervisor the kernel is theoretically slower and slightly larger. config PARAVIRT_DEBUG bool "paravirt-ops debugging" depends on PARAVIRT && DEBUG_KERNEL ---help--- Enable to debug paravirt_ops internals. Specifically, BUG if a paravirt_op is missing when it is called. config PARAVIRT_SPINLOCKS bool "Paravirtualization layer for spinlocks" depends on PARAVIRT && SMP select UNINLINE_SPIN_UNLOCK ---help--- Paravirtualized spinlocks allow a pvops backend to replace the spinlock implementation with something virtualization-friendly (for example, block the virtual CPU rather than spinning). It has a minimal impact on native kernels and gives a nice performance benefit on paravirtualized KVM / Xen kernels. If you are unsure how to answer this question, answer Y. source "arch/x86/xen/Kconfig" config KVM_GUEST bool "KVM Guest support (including kvmclock)" depends on PARAVIRT select PARAVIRT_CLOCK default y ---help--- This option enables various optimizations for running under the KVM hypervisor. It includes a paravirtualized clock, so that instead of relying on a PIT (or probably other) emulation by the underlying device model, the host provides the guest with timing infrastructure such as time of day, and system time config KVM_DEBUG_FS bool "Enable debug information for KVM Guests in debugfs" depends on KVM_GUEST && DEBUG_FS default n ---help--- This option enables collection of various statistics for KVM guest. Statistics are displayed in debugfs filesystem. Enabling this option may incur significant overhead. source "arch/x86/lguest/Kconfig" config PARAVIRT_TIME_ACCOUNTING bool "Paravirtual steal time accounting" depends on PARAVIRT default n ---help--- Select this option to enable fine granularity task steal time accounting. Time spent executing other tasks in parallel with the current vCPU is discounted from the vCPU power. To account for that, there can be a small performance impact. If in doubt, say N here. config PARAVIRT_CLOCK bool endif #HYPERVISOR_GUEST config NO_BOOTMEM def_bool y config MEMTEST bool "Memtest" ---help--- This option adds a kernel parameter 'memtest', which allows memtest to be set. memtest=0, mean disabled; -- default memtest=1, mean do 1 test pattern; ... memtest=4, mean do 4 test patterns. If you are unsure how to answer this question, answer N. config X86_SUMMIT_NUMA def_bool y depends on X86_32 && NUMA && X86_32_NON_STANDARD config X86_CYCLONE_TIMER def_bool y depends on X86_SUMMIT source "arch/x86/Kconfig.cpu" config HPET_TIMER def_bool X86_64 prompt "HPET Timer Support" if X86_32 ---help--- Use the IA-PC HPET (High Precision Event Timer) to manage time in preference to the PIT and RTC, if a HPET is present. HPET is the next generation timer replacing legacy 8254s. The HPET provides a stable time base on SMP systems, unlike the TSC, but it is more expensive to access, as it is off-chip. You can find the HPET spec at . You can safely choose Y here. However, HPET will only be activated if the platform and the BIOS support this feature. Otherwise the 8254 will be used for timing services. Choose N to continue using the legacy 8254 timer. config HPET_EMULATE_RTC def_bool y depends on HPET_TIMER && (RTC=y || RTC=m || RTC_DRV_CMOS=m || RTC_DRV_CMOS=y) config APB_TIMER def_bool y if X86_INTEL_MID prompt "Intel MID APB Timer Support" if X86_INTEL_MID select DW_APB_TIMER depends on X86_INTEL_MID && SFI help APB timer is the replacement for 8254, HPET on X86 MID platforms. The APBT provides a stable time base on SMP systems, unlike the TSC, but it is more expensive to access, as it is off-chip. APB timers are always running regardless of CPU C states, they are used as per CPU clockevent device when possible. # Mark as expert because too many people got it wrong. # The code disables itself when not needed. config DMI default y select DMI_SCAN_MACHINE_NON_EFI_FALLBACK bool "Enable DMI scanning" if EXPERT ---help--- Enabled scanning of DMI to identify machine quirks. Say Y here unless you have verified that your setup is not affected by entries in the DMI blacklist. Required by PNP BIOS code. config GART_IOMMU bool "Old AMD GART IOMMU support" select SWIOTLB depends on X86_64 && PCI && AMD_NB ---help--- Provides a driver for older AMD Athlon64/Opteron/Turion/Sempron GART based hardware IOMMUs. The GART supports full DMA access for devices with 32-bit access limitations, on systems with more than 3 GB. This is usually needed for USB, sound, many IDE/SATA chipsets and some other devices. Newer systems typically have a modern AMD IOMMU, supported via the CONFIG_AMD_IOMMU=y config option. In normal configurations this driver is only active when needed: there's more than 3 GB of memory and the system contains a 32-bit limited device. If unsure, say Y. config CALGARY_IOMMU bool "IBM Calgary IOMMU support" select SWIOTLB depends on X86_64 && PCI ---help--- Support for hardware IOMMUs in IBM's xSeries x366 and x460 systems. Needed to run systems with more than 3GB of memory properly with 32-bit PCI devices that do not support DAC (Double Address Cycle). Calgary also supports bus level isolation, where all DMAs pass through the IOMMU. This prevents them from going anywhere except their intended destination. This catches hard-to-find kernel bugs and mis-behaving drivers and devices that do not use the DMA-API properly to set up their DMA buffers. The IOMMU can be turned off at boot time with the iommu=off parameter. Normally the kernel will make the right choice by itself. If unsure, say Y. config CALGARY_IOMMU_ENABLED_BY_DEFAULT def_bool y prompt "Should Calgary be enabled by default?" depends on CALGARY_IOMMU ---help--- Should Calgary be enabled by default? if you choose 'y', Calgary will be used (if it exists). If you choose 'n', Calgary will not be used even if it exists. If you choose 'n' and would like to use Calgary anyway, pass 'iommu=calgary' on the kernel command line. If unsure, say Y. # need this always selected by IOMMU for the VIA workaround config SWIOTLB def_bool y if X86_64 ---help--- Support for software bounce buffers used on x86-64 systems which don't have a hardware IOMMU. Using this PCI devices which can only access 32-bits of memory can be used on systems with more than 3 GB of memory. If unsure, say Y. config IOMMU_HELPER def_bool y depends on CALGARY_IOMMU || GART_IOMMU || SWIOTLB || AMD_IOMMU config MAXSMP bool "Enable Maximum number of SMP Processors and NUMA Nodes" depends on X86_64 && SMP && DEBUG_KERNEL select CPUMASK_OFFSTACK ---help--- Enable maximum number of CPUS and NUMA Nodes for this architecture. If unsure, say N. config NR_CPUS int "Maximum number of CPUs" if SMP && !MAXSMP range 2 8 if SMP && X86_32 && !X86_BIGSMP range 2 512 if SMP && !MAXSMP && !CPUMASK_OFFSTACK range 2 8192 if SMP && !MAXSMP && CPUMASK_OFFSTACK && X86_64 default "1" if !SMP default "8192" if MAXSMP default "32" if SMP && (X86_NUMAQ || X86_SUMMIT || X86_BIGSMP || X86_ES7000) default "8" if SMP ---help--- This allows you to specify the maximum number of CPUs which this kernel will support. If CPUMASK_OFFSTACK is enabled, the maximum supported value is 4096, otherwise the maximum value is 512. The minimum value which makes sense is 2. This is purely to save memory - each supported CPU adds approximately eight kilobytes to the kernel image. config SCHED_SMT bool "SMT (Hyperthreading) scheduler support" depends on X86_HT ---help--- SMT scheduler support improves the CPU scheduler's decision making when dealing with Intel Pentium 4 chips with HyperThreading at a cost of slightly increased overhead in some places. If unsure say N here. config SCHED_MC def_bool y prompt "Multi-core scheduler support" depends on X86_HT ---help--- Multi-core scheduler support improves the CPU scheduler's decision making when dealing with multi-core CPU chips at a cost of slightly increased overhead in some places. If unsure say N here. source "kernel/Kconfig.preempt" config X86_UP_APIC bool "Local APIC support on uniprocessors" depends on X86_32 && !SMP && !X86_32_NON_STANDARD && !PCI_MSI ---help--- A local APIC (Advanced Programmable Interrupt Controller) is an integrated interrupt controller in the CPU. If you have a single-CPU system which has a processor with a local APIC, you can say Y here to enable and use it. If you say Y here even though your machine doesn't have a local APIC, then the kernel will still run with no slowdown at all. The local APIC supports CPU-generated self-interrupts (timer, performance counters), and the NMI watchdog which detects hard lockups. config X86_UP_IOAPIC bool "IO-APIC support on uniprocessors" depends on X86_UP_APIC ---help--- An IO-APIC (I/O Advanced Programmable Interrupt Controller) is an SMP-capable replacement for PC-style interrupt controllers. Most SMP systems and many recent uniprocessor systems have one. If you have a single-CPU system with an IO-APIC, you can say Y here to use it. If you say Y here even though your machine doesn't have an IO-APIC, then the kernel will still run with no slowdown at all. config X86_LOCAL_APIC def_bool y depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC || PCI_MSI config X86_IO_APIC def_bool y depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_IOAPIC || PCI_MSI config X86_VISWS_APIC def_bool y depends on X86_32 && X86_VISWS config X86_REROUTE_FOR_BROKEN_BOOT_IRQS bool "Reroute for broken boot IRQs" depends on X86_IO_APIC ---help--- This option enables a workaround that fixes a source of spurious interrupts. This is recommended when threaded interrupt handling is used on systems where the generation of superfluous "boot interrupts" cannot be disabled. Some chipsets generate a legacy INTx "boot IRQ" when the IRQ entry in the chipset's IO-APIC is masked (as, e.g. the RT kernel does during interrupt handling). On chipsets where this boot IRQ generation cannot be disabled, this workaround keeps the original IRQ line masked so that only the equivalent "boot IRQ" is delivered to the CPUs. The workaround also tells the kernel to set up the IRQ handler on the boot IRQ line. In this way only one interrupt is delivered to the kernel. Otherwise the spurious second interrupt may cause the kernel to bring down (vital) interrupt lines. Only affects "broken" chipsets. Interrupt sharing may be increased on these systems. config X86_MCE bool "Machine Check / overheating reporting" default y ---help--- Machine Check support allows the processor to notify the kernel if it detects a problem (e.g. overheating, data corruption). The action the kernel takes depends on the severity of the problem, ranging from warning messages to halting the machine. config X86_MCE_INTEL def_bool y prompt "Intel MCE features" depends on X86_MCE && X86_LOCAL_APIC ---help--- Additional support for intel specific MCE features such as the thermal monitor. config X86_MCE_AMD def_bool y prompt "AMD MCE features" depends on X86_MCE && X86_LOCAL_APIC ---help--- Additional support for AMD specific MCE features such as the DRAM Error Threshold. config X86_ANCIENT_MCE bool "Support for old Pentium 5 / WinChip machine checks" depends on X86_32 && X86_MCE ---help--- Include support for machine check handling on old Pentium 5 or WinChip systems. These typically need to be enabled explicitly on the command line. config X86_MCE_THRESHOLD depends on X86_MCE_AMD || X86_MCE_INTEL def_bool y config X86_MCE_INJECT depends on X86_MCE tristate "Machine check injector support" ---help--- Provide support for injecting machine checks for testing purposes. If you don't know what a machine check is and you don't do kernel QA it is safe to say n. config X86_THERMAL_VECTOR def_bool y depends on X86_MCE_INTEL config VM86 bool "Enable VM86 support" if EXPERT default y depends on X86_32 ---help--- This option is required by programs like DOSEMU to run 16-bit legacy code on X86 processors. It also may be needed by software like XFree86 to initialize some video cards via BIOS. Disabling this option saves about 6k. config TOSHIBA tristate "Toshiba Laptop support" depends on X86_32 ---help--- This adds a driver to safely access the System Management Mode of the CPU on Toshiba portables with a genuine Toshiba BIOS. It does not work on models with a Phoenix BIOS. The System Management Mode is used to set the BIOS and power saving options on Toshiba portables. For information on utilities to make use of this driver see the Toshiba Linux utilities web site at: . Say Y if you intend to run this kernel on a Toshiba portable. Say N otherwise. config I8K tristate "Dell laptop support" select HWMON ---help--- This adds a driver to safely access the System Management Mode of the CPU on the Dell Inspiron 8000. The System Management Mode is used to read cpu temperature and cooling fan status and to control the fans on the I8K portables. This driver has been tested only on the Inspiron 8000 but it may also work with other Dell laptops. You can force loading on other models by passing the parameter `force=1' to the module. Use at your own risk. For information on utilities to make use of this driver see the I8K Linux utilities web site at: Say Y if you intend to run this kernel on a Dell Inspiron 8000. Say N otherwise. config X86_REBOOTFIXUPS bool "Enable X86 board specific fixups for reboot" depends on X86_32 ---help--- This enables chipset and/or board specific fixups to be done in order to get reboot to work correctly. This is only needed on some combinations of hardware and BIOS. The symptom, for which this config is intended, is when reboot ends with a stalled/hung system. Currently, the only fixup is for the Geode machines using CS5530A and CS5536 chipsets and the RDC R-321x SoC. Say Y if you want to enable the fixup. Currently, it's safe to enable this option even if you don't need it. Say N otherwise. config MICROCODE tristate "CPU microcode loading support" depends on CPU_SUP_AMD || CPU_SUP_INTEL select FW_LOADER ---help--- If you say Y here, you will be able to update the microcode on certain Intel and AMD processors. The Intel support is for the IA32 family, e.g. Pentium Pro, Pentium II, Pentium III, Pentium 4, Xeon etc. The AMD support is for families 0x10 and later. You will obviously need the actual microcode binary data itself which is not shipped with the Linux kernel. This option selects the general module only, you need to select at least one vendor specific module as well. To compile this driver as a module, choose M here: the module will be called microcode. config MICROCODE_INTEL bool "Intel microcode loading support" depends on MICROCODE default MICROCODE select FW_LOADER ---help--- This options enables microcode patch loading support for Intel processors. For latest news and information on obtaining all the required Intel ingredients for this driver, check: . config MICROCODE_AMD bool "AMD microcode loading support" depends on MICROCODE select FW_LOADER ---help--- If you select this option, microcode patch loading support for AMD processors will be enabled. config MICROCODE_OLD_INTERFACE def_bool y depends on MICROCODE config MICROCODE_INTEL_EARLY def_bool n config MICROCODE_AMD_EARLY def_bool n config MICROCODE_EARLY bool "Early load microcode" depends on MICROCODE=y && BLK_DEV_INITRD select MICROCODE_INTEL_EARLY if MICROCODE_INTEL select MICROCODE_AMD_EARLY if MICROCODE_AMD default y help This option provides functionality to read additional microcode data at the beginning of initrd image. The data tells kernel to load microcode to CPU's as early as possible. No functional change if no microcode data is glued to the initrd, therefore it's safe to say Y. config X86_MSR tristate "/dev/cpu/*/msr - Model-specific register support" ---help--- This device gives privileged processes access to the x86 Model-Specific Registers (MSRs). It is a character device with major 202 and minors 0 to 31 for /dev/cpu/0/msr to /dev/cpu/31/msr. MSR accesses are directed to a specific CPU on multi-processor systems. config X86_CPUID tristate "/dev/cpu/*/cpuid - CPU information support" ---help--- This device gives processes access to the x86 CPUID instruction to be executed on a specific processor. It is a character device with major 203 and minors 0 to 31 for /dev/cpu/0/cpuid to /dev/cpu/31/cpuid. choice prompt "High Memory Support" default HIGHMEM64G if X86_NUMAQ default HIGHMEM4G depends on X86_32 config NOHIGHMEM bool "off" depends on !X86_NUMAQ ---help--- Linux can use up to 64 Gigabytes of physical memory on x86 systems. However, the address space of 32-bit x86 processors is only 4 Gigabytes large. That means that, if you have a large amount of physical memory, not all of it can be "permanently mapped" by the kernel. The physical memory that's not permanently mapped is called "high memory". If you are compiling a kernel which will never run on a machine with more than 1 Gigabyte total physical RAM, answer "off" here (default choice and suitable for most users). This will result in a "3GB/1GB" split: 3GB are mapped so that each process sees a 3GB virtual memory space and the remaining part of the 4GB virtual memory space is used by the kernel to permanently map as much physical memory as possible. If the machine has between 1 and 4 Gigabytes physical RAM, then answer "4GB" here. If more than 4 Gigabytes is used then answer "64GB" here. This selection turns Intel PAE (Physical Address Extension) mode on. PAE implements 3-level paging on IA32 processors. PAE is fully supported by Linux, PAE mode is implemented on all recent Intel processors (Pentium Pro and better). NOTE: If you say "64GB" here, then the kernel will not boot on CPUs that don't support PAE! The actual amount of total physical memory will either be auto detected or can be forced by using a kernel command line option such as "mem=256M". (Try "man bootparam" or see the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) If unsure, say "off". config HIGHMEM4G bool "4GB" depends on !X86_NUMAQ ---help--- Select this if you have a 32-bit processor and between 1 and 4 gigabytes of physical RAM. config HIGHMEM64G bool "64GB" depends on !M486 select X86_PAE ---help--- Select this if you have a 32-bit processor and more than 4 gigabytes of physical RAM. endchoice choice prompt "Memory split" if EXPERT default VMSPLIT_3G depends on X86_32 ---help--- Select the desired split between kernel and user memory. If the address range available to the kernel is less than the physical memory installed, the remaining memory will be available as "high memory". Accessing high memory is a little more costly than low memory, as it needs to be mapped into the kernel first. Note that increasing the kernel address space limits the range available to user programs, making the address space there tighter. Selecting anything other than the default 3G/1G split will also likely make your kernel incompatible with binary-only kernel modules. If you are not absolutely sure what you are doing, leave this option alone! config VMSPLIT_3G bool "3G/1G user/kernel split" config VMSPLIT_3G_OPT depends on !X86_PAE bool "3G/1G user/kernel split (for full 1G low memory)" config VMSPLIT_2G bool "2G/2G user/kernel split" config VMSPLIT_2G_OPT depends on !X86_PAE bool "2G/2G user/kernel split (for full 2G low memory)" config VMSPLIT_1G bool "1G/3G user/kernel split" endchoice config PAGE_OFFSET hex default 0xB0000000 if VMSPLIT_3G_OPT default 0x80000000 if VMSPLIT_2G default 0x78000000 if VMSPLIT_2G_OPT default 0x40000000 if VMSPLIT_1G default 0xC0000000 depends on X86_32 config HIGHMEM def_bool y depends on X86_32 && (HIGHMEM64G || HIGHMEM4G) config X86_PAE bool "PAE (Physical Address Extension) Support" depends on X86_32 && !HIGHMEM4G ---help--- PAE is required for NX support, and furthermore enables larger swapspace support for non-overcommit purposes. It has the cost of more pagetable lookup overhead, and also consumes more pagetable space per process. config ARCH_PHYS_ADDR_T_64BIT def_bool y depends on X86_64 || X86_PAE config ARCH_DMA_ADDR_T_64BIT def_bool y depends on X86_64 || HIGHMEM64G config DIRECT_GBPAGES bool "Enable 1GB pages for kernel pagetables" if EXPERT default y depends on X86_64 ---help--- Allow the kernel linear mapping to use 1GB pages on CPUs that support it. This can improve the kernel's performance a tiny bit by reducing TLB pressure. If in doubt, say "Y". # Common NUMA Features config NUMA bool "Numa Memory Allocation and Scheduler Support" depends on SMP depends on X86_64 || (X86_32 && HIGHMEM64G && (X86_NUMAQ || X86_BIGSMP || X86_SUMMIT && ACPI)) default y if (X86_NUMAQ || X86_SUMMIT || X86_BIGSMP) ---help--- Enable NUMA (Non Uniform Memory Access) support. The kernel will try to allocate memory used by a CPU on the local memory controller of the CPU and add some more NUMA awareness to the kernel. For 64-bit this is recommended if the system is Intel Core i7 (or later), AMD Opteron, or EM64T NUMA. For 32-bit this is only needed on (rare) 32-bit-only platforms that support NUMA topologies, such as NUMAQ / Summit, or if you boot a 32-bit kernel on a 64-bit NUMA platform. Otherwise, you should say N. comment "NUMA (Summit) requires SMP, 64GB highmem support, ACPI" depends on X86_32 && X86_SUMMIT && (!HIGHMEM64G || !ACPI) config AMD_NUMA def_bool y prompt "Old style AMD Opteron NUMA detection" depends on X86_64 && NUMA && PCI ---help--- Enable AMD NUMA node topology detection. You should say Y here if you have a multi processor AMD system. This uses an old method to read the NUMA configuration directly from the builtin Northbridge of Opteron. It is recommended to use X86_64_ACPI_NUMA instead, which also takes priority if both are compiled in. config X86_64_ACPI_NUMA def_bool y prompt "ACPI NUMA detection" depends on X86_64 && NUMA && ACPI && PCI select ACPI_NUMA ---help--- Enable ACPI SRAT based node topology detection. # Some NUMA nodes have memory ranges that span # other nodes. Even though a pfn is valid and # between a node's start and end pfns, it may not # reside on that node. See memmap_init_zone() # for details. config NODES_SPAN_OTHER_NODES def_bool y depends on X86_64_ACPI_NUMA config NUMA_EMU bool "NUMA emulation" depends on NUMA ---help--- Enable NUMA emulation. A flat machine will be split into virtual nodes when booted with "numa=fake=N", where N is the number of nodes. This is only useful for debugging. config NODES_SHIFT int "Maximum NUMA Nodes (as a power of 2)" if !MAXSMP range 1 10 default "10" if MAXSMP default "6" if X86_64 default "4" if X86_NUMAQ default "3" depends on NEED_MULTIPLE_NODES ---help--- Specify the maximum number of NUMA Nodes available on the target system. Increases memory reserved to accommodate various tables. config ARCH_HAVE_MEMORY_PRESENT def_bool y depends on X86_32 && DISCONTIGMEM config NEED_NODE_MEMMAP_SIZE def_bool y depends on X86_32 && (DISCONTIGMEM || SPARSEMEM) config ARCH_FLATMEM_ENABLE def_bool y depends on X86_32 && !NUMA config ARCH_DISCONTIGMEM_ENABLE def_bool y depends on NUMA && X86_32 config ARCH_DISCONTIGMEM_DEFAULT def_bool y depends on NUMA && X86_32 config ARCH_SPARSEMEM_ENABLE def_bool y depends on X86_64 || NUMA || X86_32 || X86_32_NON_STANDARD select SPARSEMEM_STATIC if X86_32 select SPARSEMEM_VMEMMAP_ENABLE if X86_64 config ARCH_SPARSEMEM_DEFAULT def_bool y depends on X86_64 config ARCH_SELECT_MEMORY_MODEL def_bool y depends on ARCH_SPARSEMEM_ENABLE config ARCH_MEMORY_PROBE bool "Enable sysfs memory/probe interface" depends on X86_64 && MEMORY_HOTPLUG help This option enables a sysfs memory/probe interface for testing. See Documentation/memory-hotplug.txt for more information. If you are unsure how to answer this question, answer N. config ARCH_PROC_KCORE_TEXT def_bool y depends on X86_64 && PROC_KCORE config ILLEGAL_POINTER_VALUE hex default 0 if X86_32 default 0xdead000000000000 if X86_64 source "mm/Kconfig" config HIGHPTE bool "Allocate 3rd-level pagetables from highmem" depends on HIGHMEM ---help--- The VM uses one page table entry for each page of physical memory. For systems with a lot of RAM, this can be wasteful of precious low memory. Setting this option will put user-space page table entries in high memory. config X86_CHECK_BIOS_CORRUPTION bool "Check for low memory corruption" ---help--- Periodically check for memory corruption in low memory, which is suspected to be caused by BIOS. Even when enabled in the configuration, it is disabled at runtime. Enable it by setting "memory_corruption_check=1" on the kernel command line. By default it scans the low 64k of memory every 60 seconds; see the memory_corruption_check_size and memory_corruption_check_period parameters in Documentation/kernel-parameters.txt to adjust this. When enabled with the default parameters, this option has almost no overhead, as it reserves a relatively small amount of memory and scans it infrequently. It both detects corruption and prevents it from affecting the running system. It is, however, intended as a diagnostic tool; if repeatable BIOS-originated corruption always affects the same memory, you can use memmap= to prevent the kernel from using that memory. config X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK bool "Set the default setting of memory_corruption_check" depends on X86_CHECK_BIOS_CORRUPTION default y ---help--- Set whether the default state of memory_corruption_check is on or off. config X86_RESERVE_LOW int "Amount of low memory, in kilobytes, to reserve for the BIOS" default 64 range 4 640 ---help--- Specify the amount of low memory to reserve for the BIOS. The first page contains BIOS data structures that the kernel must not use, so that page must always be reserved. By default we reserve the first 64K of physical RAM, as a number of BIOSes are known to corrupt that memory range during events such as suspend/resume or monitor cable insertion, so it must not be used by the kernel. You can set this to 4 if you are absolutely sure that you trust the BIOS to get all its memory reservations and usages right. If you know your BIOS have problems beyond the default 64K area, you can set this to 640 to avoid using the entire low memory range. If you have doubts about the BIOS (e.g. suspend/resume does not work or there's kernel crashes after certain hardware hotplug events) then you might want to enable X86_CHECK_BIOS_CORRUPTION=y to allow the kernel to check typical corruption patterns. Leave this to the default value of 64 if you are unsure. config MATH_EMULATION bool prompt "Math emulation" if X86_32 ---help--- Linux can emulate a math coprocessor (used for floating point operations) if you don't have one. 486DX and Pentium processors have a math coprocessor built in, 486SX and 386 do not, unless you added a 487DX or 387, respectively. (The messages during boot time can give you some hints here ["man dmesg"].) Everyone needs either a coprocessor or this emulation. If you don't have a math coprocessor, you need to say Y here; if you say Y here even though you have a coprocessor, the coprocessor will be used nevertheless. (This behavior can be changed with the kernel command line option "no387", which comes handy if your coprocessor is broken. Try "man bootparam" or see the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) This means that it is a good idea to say Y here if you intend to use this kernel on different machines. More information about the internals of the Linux math coprocessor emulation can be found in . If you are not sure, say Y; apart from resulting in a 66 KB bigger kernel, it won't hurt. config MTRR def_bool y prompt "MTRR (Memory Type Range Register) support" if EXPERT ---help--- On Intel P6 family processors (Pentium Pro, Pentium II and later) the Memory Type Range Registers (MTRRs) may be used to control processor access to memory ranges. This is most useful if you have a video (VGA) card on a PCI or AGP bus. Enabling write-combining allows bus write transfers to be combined into a larger transfer before bursting over the PCI/AGP bus. This can increase performance of image write operations 2.5 times or more. Saying Y here creates a /proc/mtrr file which may be used to manipulate your processor's MTRRs. Typically the X server should use this. This code has a reasonably generic interface so that similar control registers on other processors can be easily supported as well: The Cyrix 6x86, 6x86MX and M II processors have Address Range Registers (ARRs) which provide a similar functionality to MTRRs. For these, the ARRs are used to emulate the MTRRs. The AMD K6-2 (stepping 8 and above) and K6-3 processors have two MTRRs. The Centaur C6 (WinChip) has 8 MCRs, allowing write-combining. All of these processors are supported by this code and it makes sense to say Y here if you have one of them. Saying Y here also fixes a problem with buggy SMP BIOSes which only set the MTRRs for the boot CPU and not for the secondary CPUs. This can lead to all sorts of problems, so it's good to say Y here. You can safely say Y even if your machine doesn't have MTRRs, you'll just add about 9 KB to your kernel. See for more information. config MTRR_SANITIZER def_bool y prompt "MTRR cleanup support" depends on MTRR ---help--- Convert MTRR layout from continuous to discrete, so X drivers can add writeback entries. Can be disabled with disable_mtrr_cleanup on the kernel command line. The largest mtrr entry size for a continuous block can be set with mtrr_chunk_size. If unsure, say Y. config MTRR_SANITIZER_ENABLE_DEFAULT int "MTRR cleanup enable value (0-1)" range 0 1 default "0" depends on MTRR_SANITIZER ---help--- Enable mtrr cleanup default value config MTRR_SANITIZER_SPARE_REG_NR_DEFAULT int "MTRR cleanup spare reg num (0-7)" range 0 7 default "1" depends on MTRR_SANITIZER ---help--- mtrr cleanup spare entries default, it can be changed via mtrr_spare_reg_nr=N on the kernel command line. config X86_PAT def_bool y prompt "x86 PAT support" if EXPERT depends on MTRR ---help--- Use PAT attributes to setup page level cache control. PATs are the modern equivalents of MTRRs and are much more flexible than MTRRs. Say N here if you see bootup problems (boot crash, boot hang, spontaneous reboots) or a non-working video driver. If unsure, say Y. config ARCH_USES_PG_UNCACHED def_bool y depends on X86_PAT config ARCH_RANDOM def_bool y prompt "x86 architectural random number generator" if EXPERT ---help--- Enable the x86 architectural RDRAND instruction (Intel Bull Mountain technology) to generate random numbers. If supported, this is a high bandwidth, cryptographically secure hardware random number generator. config X86_SMAP def_bool y prompt "Supervisor Mode Access Prevention" if EXPERT ---help--- Supervisor Mode Access Prevention (SMAP) is a security feature in newer Intel processors. There is a small performance cost if this enabled and turned on; there is also a small increase in the kernel size if this is enabled. If unsure, say Y. config EFI bool "EFI runtime service support" depends on ACPI select UCS2_STRING ---help--- This enables the kernel to use EFI runtime services that are available (such as the EFI variable services). This option is only useful on systems that have EFI firmware. In addition, you should use the latest ELILO loader available at in order to take advantage of EFI runtime services. However, even with this option, the resultant kernel should continue to boot on existing non-EFI platforms. config EFI_STUB bool "EFI stub support" depends on EFI ---help--- This kernel feature allows a bzImage to be loaded directly by EFI firmware without the use of a bootloader. See Documentation/efi-stub.txt for more information. config SECCOMP def_bool y prompt "Enable seccomp to safely compute untrusted bytecode" ---help--- This kernel feature is useful for number crunching applications that may need to compute untrusted bytecode during their execution. By using pipes or other transports made available to the process as file descriptors supporting the read/write syscalls, it's possible to isolate those applications in their own address space using seccomp. Once seccomp is enabled via prctl(PR_SET_SECCOMP), it cannot be disabled and the task is only allowed to execute a few safe syscalls defined by each seccomp mode. If unsure, say Y. Only embedded should say N here. source kernel/Kconfig.hz config KEXEC bool "kexec system call" ---help--- kexec is a system call that implements the ability to shutdown your current kernel, and to start another kernel. It is like a reboot but it is independent of the system firmware. And like a reboot you can start any kernel with it, not just Linux. The name comes from the similarity to the exec system call. It is an ongoing process to be certain the hardware in a machine is properly shutdown, so do not be surprised if this code does not initially work for you. As of this writing the exact hardware interface is strongly in flux, so no good recommendation can be made. config CRASH_DUMP bool "kernel crash dumps" depends on X86_64 || (X86_32 && HIGHMEM) ---help--- Generate crash dump after being started by kexec. This should be normally only set in special crash dump kernels which are loaded in the main kernel with kexec-tools into a specially reserved region and then later executed after a crash by kdump/kexec. The crash dump kernel must be compiled to a memory address not used by the main kernel or BIOS using PHYSICAL_START, or it must be built as a relocatable image (CONFIG_RELOCATABLE=y). For more details see Documentation/kdump/kdump.txt config KEXEC_JUMP bool "kexec jump" depends on KEXEC && HIBERNATION ---help--- Jump between original kernel and kexeced kernel and invoke code in physical address mode via KEXEC config PHYSICAL_START hex "Physical address where the kernel is loaded" if (EXPERT || CRASH_DUMP) default "0x1000000" ---help--- This gives the physical address where the kernel is loaded. If kernel is a not relocatable (CONFIG_RELOCATABLE=n) then bzImage will decompress itself to above physical address and run from there. Otherwise, bzImage will run from the address where it has been loaded by the boot loader and will ignore above physical address. In normal kdump cases one does not have to set/change this option as now bzImage can be compiled as a completely relocatable image (CONFIG_RELOCATABLE=y) and be used to load and run from a different address. This option is mainly useful for the folks who don't want to use a bzImage for capturing the crash dump and want to use a vmlinux instead. vmlinux is not relocatable hence a kernel needs to be specifically compiled to run from a specific memory area (normally a reserved region) and this option comes handy. So if you are using bzImage for capturing the crash dump, leave the value here unchanged to 0x1000000 and set CONFIG_RELOCATABLE=y. Otherwise if you plan to use vmlinux for capturing the crash dump change this value to start of the reserved region. In other words, it can be set based on the "X" value as specified in the "crashkernel=YM@XM" command line boot parameter passed to the panic-ed kernel. Please take a look at Documentation/kdump/kdump.txt for more details about crash dumps. Usage of bzImage for capturing the crash dump is recommended as one does not have to build two kernels. Same kernel can be used as production kernel and capture kernel. Above option should have gone away after relocatable bzImage support is introduced. But it is present because there are users out there who continue to use vmlinux for dump capture. This option should go away down the line. Don't change this unless you know what you are doing. config RELOCATABLE bool "Build a relocatable kernel" default y ---help--- This builds a kernel image that retains relocation information so it can be loaded someplace besides the default 1MB. The relocations tend to make the kernel binary about 10% larger, but are discarded at runtime. One use is for the kexec on panic case where the recovery kernel must live at a different physical address than the primary kernel. Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address it has been loaded at and the compile time physical address (CONFIG_PHYSICAL_START) is used as the minimum location. config RANDOMIZE_BASE bool "Randomize the address of the kernel image" depends on RELOCATABLE depends on !HIBERNATION default n ---help--- Randomizes the physical and virtual address at which the kernel image is decompressed, as a security feature that deters exploit attempts relying on knowledge of the location of kernel internals. Entropy is generated using the RDRAND instruction if it is supported. If RDTSC is supported, it is used as well. If neither RDRAND nor RDTSC are supported, then randomness is read from the i8254 timer. The kernel will be offset by up to RANDOMIZE_BASE_MAX_OFFSET, and aligned according to PHYSICAL_ALIGN. Since the kernel is built using 2GiB addressing, and PHYSICAL_ALGIN must be at a minimum of 2MiB, only 10 bits of entropy is theoretically possible. At best, due to page table layouts, 64-bit can use 9 bits of entropy and 32-bit uses 8 bits. If unsure, say N. config RANDOMIZE_BASE_MAX_OFFSET hex "Maximum kASLR offset allowed" if EXPERT depends on RANDOMIZE_BASE range 0x0 0x20000000 if X86_32 default "0x20000000" if X86_32 range 0x0 0x40000000 if X86_64 default "0x40000000" if X86_64 ---help--- The lesser of RANDOMIZE_BASE_MAX_OFFSET and available physical memory is used to determine the maximal offset in bytes that will be applied to the kernel when kernel Address Space Layout Randomization (kASLR) is active. This must be a multiple of PHYSICAL_ALIGN. On 32-bit this is limited to 512MiB by page table layouts. The default is 512MiB. On 64-bit this is limited by how the kernel fixmap page table is positioned, so this cannot be larger than 1GiB currently. Without RANDOMIZE_BASE, there is a 512MiB to 1.5GiB split between kernel and modules. When RANDOMIZE_BASE_MAX_OFFSET is above 512MiB, the modules area will shrink to compensate, up to the current maximum 1GiB to 1GiB split. The default is 1GiB. If unsure, leave at the default value. # Relocation on x86 needs some additional build support config X86_NEED_RELOCS def_bool y depends on RANDOMIZE_BASE || (X86_32 && RELOCATABLE) config PHYSICAL_ALIGN hex "Alignment value to which kernel should be aligned" default "0x200000" range 0x2000 0x1000000 if X86_32 range 0x200000 0x1000000 if X86_64 ---help--- This value puts the alignment restrictions on physical address where kernel is loaded and run from. Kernel is compiled for an address which meets above alignment restriction. If bootloader loads the kernel at a non-aligned address and CONFIG_RELOCATABLE is set, kernel will move itself to nearest address aligned to above value and run from there. If bootloader loads the kernel at a non-aligned address and CONFIG_RELOCATABLE is not set, kernel will ignore the run time load address and decompress itself to the address it has been compiled for and run from there. The address for which kernel is compiled already meets above alignment restrictions. Hence the end result is that kernel runs from a physical address meeting above alignment restrictions. On 32-bit this value must be a multiple of 0x2000. On 64-bit this value must be a multiple of 0x200000. Don't change this unless you know what you are doing. config HOTPLUG_CPU bool "Support for hot-pluggable CPUs" depends on SMP ---help--- Say Y here to allow turning CPUs off and on. CPUs can be controlled through /sys/devices/system/cpu. ( Note: power management support will enable this option automatically on SMP systems. ) Say N if you want to disable CPU hotplug. config BOOTPARAM_HOTPLUG_CPU0 bool "Set default setting of cpu0_hotpluggable" default n depends on HOTPLUG_CPU ---help--- Set whether default state of cpu0_hotpluggable is on or off. Say Y here to enable CPU0 hotplug by default. If this switch is turned on, there is no need to give cpu0_hotplug kernel parameter and the CPU0 hotplug feature is enabled by default. Please note: there are two known CPU0 dependencies if you want to enable the CPU0 hotplug feature either by this switch or by cpu0_hotplug kernel parameter. First, resume from hibernate or suspend always starts from CPU0. So hibernate and suspend are prevented if CPU0 is offline. Second dependency is PIC interrupts always go to CPU0. CPU0 can not offline if any interrupt can not migrate out of CPU0. There may be other CPU0 dependencies. Please make sure the dependencies are under your control before you enable this feature. Say N if you don't want to enable CPU0 hotplug feature by default. You still can enable the CPU0 hotplug feature at boot by kernel parameter cpu0_hotplug. config DEBUG_HOTPLUG_CPU0 def_bool n prompt "Debug CPU0 hotplug" depends on HOTPLUG_CPU ---help--- Enabling this option offlines CPU0 (if CPU0 can be offlined) as soon as possible and boots up userspace with CPU0 offlined. User can online CPU0 back after boot time. To debug CPU0 hotplug, you need to enable CPU0 offline/online feature by either turning on CONFIG_BOOTPARAM_HOTPLUG_CPU0 during compilation or giving cpu0_hotplug kernel parameter at boot. If unsure, say N. config COMPAT_VDSO def_bool y prompt "Compat VDSO support" depends on X86_32 || IA32_EMULATION ---help--- Map the 32-bit VDSO to the predictable old-style address too. Say N here if you are running a sufficiently recent glibc version (2.3.3 or later), to remove the high-mapped VDSO mapping and to exclusively use the randomized VDSO. If unsure, say Y. config CMDLINE_BOOL bool "Built-in kernel command line" ---help--- Allow for specifying boot arguments to the kernel at build time. On some systems (e.g. embedded ones), it is necessary or convenient to provide some or all of the kernel boot arguments with the kernel itself (that is, to not rely on the boot loader to provide them.) To compile command line arguments into the kernel, set this option to 'Y', then fill in the the boot arguments in CONFIG_CMDLINE. Systems with fully functional boot loaders (i.e. non-embedded) should leave this option set to 'N'. config CMDLINE string "Built-in kernel command string" depends on CMDLINE_BOOL default "" ---help--- Enter arguments here that should be compiled into the kernel image and used at boot time. If the boot loader provides a command line at boot time, it is appended to this string to form the full kernel command line, when the system boots. However, you can use the CONFIG_CMDLINE_OVERRIDE option to change this behavior. In most cases, the command line (whether built-in or provided by the boot loader) should specify the device for the root file system. config CMDLINE_OVERRIDE bool "Built-in command line overrides boot loader arguments" depends on CMDLINE_BOOL ---help--- Set this option to 'Y' to have the kernel ignore the boot loader command line, and use ONLY the built-in command line. This is used to work around broken boot loaders. This should be set to 'N' under normal conditions. endmenu config ARCH_ENABLE_MEMORY_HOTPLUG def_bool y depends on X86_64 || (X86_32 && HIGHMEM) config ARCH_ENABLE_MEMORY_HOTREMOVE def_bool y depends on MEMORY_HOTPLUG config USE_PERCPU_NUMA_NODE_ID def_bool y depends on NUMA config ARCH_ENABLE_SPLIT_PMD_PTLOCK def_bool y depends on X86_64 || X86_PAE menu "Power management and ACPI options" config ARCH_HIBERNATION_HEADER def_bool y depends on X86_64 && HIBERNATION source "kernel/power/Kconfig" source "drivers/acpi/Kconfig" source "drivers/sfi/Kconfig" config X86_APM_BOOT def_bool y depends on APM menuconfig APM tristate "APM (Advanced Power Management) BIOS support" depends on X86_32 && PM_SLEEP ---help--- APM is a BIOS specification for saving power using several different techniques. This is mostly useful for battery powered laptops with APM compliant BIOSes. If you say Y here, the system time will be reset after a RESUME operation, the /proc/apm device will provide battery status information, and user-space programs will receive notification of APM "events" (e.g. battery status change). If you select "Y" here, you can disable actual use of the APM BIOS by passing the "apm=off" option to the kernel at boot time. Note that the APM support is almost completely disabled for machines with more than one CPU. In order to use APM, you will need supporting software. For location and more information, read and the Battery Powered Linux mini-HOWTO, available from . This driver does not spin down disk drives (see the hdparm(8) manpage ("man 8 hdparm") for that), and it doesn't turn off VESA-compliant "green" monitors. This driver does not support the TI 4000M TravelMate and the ACER 486/DX4/75 because they don't have compliant BIOSes. Many "green" desktop machines also don't have compliant BIOSes, and this driver may cause those machines to panic during the boot phase. Generally, if you don't have a battery in your machine, there isn't much point in using this driver and you should say N. If you get random kernel OOPSes or reboots that don't seem to be related to anything, try disabling/enabling this option (or disabling/enabling APM in your BIOS). Some other things you should try when experiencing seemingly random, "weird" problems: 1) make sure that you have enough swap space and that it is enabled. 2) pass the "no-hlt" option to the kernel 3) switch on floating point emulation in the kernel and pass the "no387" option to the kernel 4) pass the "floppy=nodma" option to the kernel 5) pass the "mem=4M" option to the kernel (thereby disabling all but the first 4 MB of RAM) 6) make sure that the CPU is not over clocked. 7) read the sig11 FAQ at 8) disable the cache from your BIOS settings 9) install a fan for the video card or exchange video RAM 10) install a better fan for the CPU 11) exchange RAM chips 12) exchange the motherboard. To compile this driver as a module, choose M here: the module will be called apm. if APM config APM_IGNORE_USER_SUSPEND bool "Ignore USER SUSPEND" ---help--- This option will ignore USER SUSPEND requests. On machines with a compliant APM BIOS, you want to say N. However, on the NEC Versa M series notebooks, it is necessary to say Y because of a BIOS bug. config APM_DO_ENABLE bool "Enable PM at boot time" ---help--- Enable APM features at boot time. From page 36 of the APM BIOS specification: "When disabled, the APM BIOS does not automatically power manage devices, enter the Standby State, enter the Suspend State, or take power saving steps in response to CPU Idle calls." This driver will make CPU Idle calls when Linux is idle (unless this feature is turned off -- see "Do CPU IDLE calls", below). This should always save battery power, but more complicated APM features will be dependent on your BIOS implementation. You may need to turn this option off if your computer hangs at boot time when using APM support, or if it beeps continuously instead of suspending. Turn this off if you have a NEC UltraLite Versa 33/C or a Toshiba T400CDT. This is off by default since most machines do fine without this feature. config APM_CPU_IDLE depends on CPU_IDLE bool "Make CPU Idle calls when idle" ---help--- Enable calls to APM CPU Idle/CPU Busy inside the kernel's idle loop. On some machines, this can activate improved power savings, such as a slowed CPU clock rate, when the machine is idle. These idle calls are made after the idle loop has run for some length of time (e.g., 333 mS). On some machines, this will cause a hang at boot time or whenever the CPU becomes idle. (On machines with more than one CPU, this option does nothing.) config APM_DISPLAY_BLANK bool "Enable console blanking using APM" ---help--- Enable console blanking using the APM. Some laptops can use this to turn off the LCD backlight when the screen blanker of the Linux virtual console blanks the screen. Note that this is only used by the virtual console screen blanker, and won't turn off the backlight when using the X Window system. This also doesn't have anything to do with your VESA-compliant power-saving monitor. Further, this option doesn't work for all laptops -- it might not turn off your backlight at all, or it might print a lot of errors to the console, especially if you are using gpm. config APM_ALLOW_INTS bool "Allow interrupts during APM BIOS calls" ---help--- Normally we disable external interrupts while we are making calls to the APM BIOS as a measure to lessen the effects of a badly behaving BIOS implementation. The BIOS should reenable interrupts if it needs to. Unfortunately, some BIOSes do not -- especially those in many of the newer IBM Thinkpads. If you experience hangs when you suspend, try setting this to Y. Otherwise, say N. endif # APM source "drivers/cpufreq/Kconfig" source "drivers/cpuidle/Kconfig" source "drivers/idle/Kconfig" endmenu menu "Bus options (PCI etc.)" config PCI bool "PCI support" default y ---help--- Find out whether you have a PCI motherboard. PCI is the name of a bus system, i.e. the way the CPU talks to the other stuff inside your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or VESA. If you have PCI, say Y, otherwise N. choice prompt "PCI access mode" depends on X86_32 && PCI default PCI_GOANY ---help--- On PCI systems, the BIOS can be used to detect the PCI devices and determine their configuration. However, some old PCI motherboards have BIOS bugs and may crash if this is done. Also, some embedded PCI-based systems don't have any BIOS at all. Linux can also try to detect the PCI hardware directly without using the BIOS. With this option, you can specify how Linux should detect the PCI devices. If you choose "BIOS", the BIOS will be used, if you choose "Direct", the BIOS won't be used, and if you choose "MMConfig", then PCI Express MMCONFIG will be used. If you choose "Any", the kernel will try MMCONFIG, then the direct access method and falls back to the BIOS if that doesn't work. If unsure, go with the default, which is "Any". config PCI_GOBIOS bool "BIOS" config PCI_GOMMCONFIG bool "MMConfig" config PCI_GODIRECT bool "Direct" config PCI_GOOLPC bool "OLPC XO-1" depends on OLPC config PCI_GOANY bool "Any" endchoice config PCI_BIOS def_bool y depends on X86_32 && PCI && (PCI_GOBIOS || PCI_GOANY) # x86-64 doesn't support PCI BIOS access from long mode so always go direct. config PCI_DIRECT def_bool y depends on PCI && (X86_64 || (PCI_GODIRECT || PCI_GOANY || PCI_GOOLPC || PCI_GOMMCONFIG)) config PCI_MMCONFIG def_bool y depends on X86_32 && PCI && (ACPI || SFI) && (PCI_GOMMCONFIG || PCI_GOANY) config PCI_OLPC def_bool y depends on PCI && OLPC && (PCI_GOOLPC || PCI_GOANY) config PCI_XEN def_bool y depends on PCI && XEN select SWIOTLB_XEN config PCI_DOMAINS def_bool y depends on PCI config PCI_MMCONFIG bool "Support mmconfig PCI config space access" depends on X86_64 && PCI && ACPI config PCI_CNB20LE_QUIRK bool "Read CNB20LE Host Bridge Windows" if EXPERT depends on PCI help Read the PCI windows out of the CNB20LE host bridge. This allows PCI hotplug to work on systems with the CNB20LE chipset which do not have ACPI. There's no public spec for this chipset, and this functionality is known to be incomplete. You should say N unless you know you need this. source "drivers/pci/pcie/Kconfig" source "drivers/pci/Kconfig" # x86_64 have no ISA slots, but can have ISA-style DMA. config ISA_DMA_API bool "ISA-style DMA support" if (X86_64 && EXPERT) default y help Enables ISA-style DMA support for devices requiring such controllers. If unsure, say Y. if X86_32 config ISA bool "ISA support" ---help--- Find out whether you have ISA slots on your motherboard. ISA is the name of a bus system, i.e. the way the CPU talks to the other stuff inside your box. Other bus systems are PCI, EISA, MicroChannel (MCA) or VESA. ISA is an older system, now being displaced by PCI; newer boards don't support it. If you have ISA, say Y, otherwise N. config EISA bool "EISA support" depends on ISA ---help--- The Extended Industry Standard Architecture (EISA) bus was developed as an open alternative to the IBM MicroChannel bus. The EISA bus provided some of the features of the IBM MicroChannel bus while maintaining backward compatibility with cards made for the older ISA bus. The EISA bus saw limited use between 1988 and 1995 when it was made obsolete by the PCI bus. Say Y here if you are building a kernel for an EISA-based machine. Otherwise, say N. source "drivers/eisa/Kconfig" config SCx200 tristate "NatSemi SCx200 support" ---help--- This provides basic support for National Semiconductor's (now AMD's) Geode processors. The driver probes for the PCI-IDs of several on-chip devices, so its a good dependency for other scx200_* drivers. If compiled as a module, the driver is named scx200. config SCx200HR_TIMER tristate "NatSemi SCx200 27MHz High-Resolution Timer Support" depends on SCx200 default y ---help--- This driver provides a clocksource built upon the on-chip 27MHz high-resolution timer. Its also a workaround for NSC Geode SC-1100's buggy TSC, which loses time when the processor goes idle (as is done by the scheduler). The other workaround is idle=poll boot option. config OLPC bool "One Laptop Per Child support" depends on !X86_PAE select GPIOLIB select OF select OF_PROMTREE select IRQ_DOMAIN ---help--- Add support for detecting the unique features of the OLPC XO hardware. config OLPC_XO1_PM bool "OLPC XO-1 Power Management" depends on OLPC && MFD_CS5535 && PM_SLEEP select MFD_CORE ---help--- Add support for poweroff and suspend of the OLPC XO-1 laptop. config OLPC_XO1_RTC bool "OLPC XO-1 Real Time Clock" depends on OLPC_XO1_PM && RTC_DRV_CMOS ---help--- Add support for the XO-1 real time clock, which can be used as a programmable wakeup source. config OLPC_XO1_SCI bool "OLPC XO-1 SCI extras" depends on OLPC && OLPC_XO1_PM depends on INPUT=y select POWER_SUPPLY select GPIO_CS5535 select MFD_CORE ---help--- Add support for SCI-based features of the OLPC XO-1 laptop: - EC-driven system wakeups - Power button - Ebook switch - Lid switch - AC adapter status updates - Battery status updates config OLPC_XO15_SCI bool "OLPC XO-1.5 SCI extras" depends on OLPC && ACPI select POWER_SUPPLY ---help--- Add support for SCI-based features of the OLPC XO-1.5 laptop: - EC-driven system wakeups - AC adapter status updates - Battery status updates config ALIX bool "PCEngines ALIX System Support (LED setup)" select GPIOLIB ---help--- This option enables system support for the PCEngines ALIX. At present this just sets up LEDs for GPIO control on ALIX2/3/6 boards. However, other system specific setup should get added here. Note: You must still enable the drivers for GPIO and LED support (GPIO_CS5535 & LEDS_GPIO) to actually use the LEDs Note: You have to set alix.force=1 for boards with Award BIOS. config NET5501 bool "Soekris Engineering net5501 System Support (LEDS, GPIO, etc)" select GPIOLIB ---help--- This option enables system support for the Soekris Engineering net5501. config GEOS bool "Traverse Technologies GEOS System Support (LEDS, GPIO, etc)" select GPIOLIB depends on DMI ---help--- This option enables system support for the Traverse Technologies GEOS. config TS5500 bool "Technologic Systems TS-5500 platform support" depends on MELAN select CHECK_SIGNATURE select NEW_LEDS select LEDS_CLASS ---help--- This option enables system support for the Technologic Systems TS-5500. endif # X86_32 config AMD_NB def_bool y depends on CPU_SUP_AMD && PCI source "drivers/pcmcia/Kconfig" source "drivers/pci/hotplug/Kconfig" config RAPIDIO tristate "RapidIO support" depends on PCI default n help If enabled this option will include drivers and the core infrastructure code to support RapidIO interconnect devices. source "drivers/rapidio/Kconfig" config X86_SYSFB bool "Mark VGA/VBE/EFI FB as generic system framebuffer" help Firmwares often provide initial graphics framebuffers so the BIOS, bootloader or kernel can show basic video-output during boot for user-guidance and debugging. Historically, x86 used the VESA BIOS Extensions and EFI-framebuffers for this, which are mostly limited to x86. This option, if enabled, marks VGA/VBE/EFI framebuffers as generic framebuffers so the new generic system-framebuffer drivers can be used on x86. If the framebuffer is not compatible with the generic modes, it is adverticed as fallback platform framebuffer so legacy drivers like efifb, vesafb and uvesafb can pick it up. If this option is not selected, all system framebuffers are always marked as fallback platform framebuffers as usual. Note: Legacy fbdev drivers, including vesafb, efifb, uvesafb, will not be able to pick up generic system framebuffers if this option is selected. You are highly encouraged to enable simplefb as replacement if you select this option. simplefb can correctly deal with generic system framebuffers. But you should still keep vesafb and others enabled as fallback if a system framebuffer is incompatible with simplefb. If unsure, say Y. endmenu menu "Executable file formats / Emulations" source "fs/Kconfig.binfmt" config IA32_EMULATION bool "IA32 Emulation" depends on X86_64 select BINFMT_ELF select COMPAT_BINFMT_ELF select HAVE_UID16 ---help--- Include code to run legacy 32-bit programs under a 64-bit kernel. You should likely turn this on, unless you're 100% sure that you don't have any 32-bit programs left. config IA32_AOUT tristate "IA32 a.out support" depends on IA32_EMULATION ---help--- Support old a.out binaries in the 32bit emulation. config X86_X32 bool "x32 ABI for 64-bit mode" depends on X86_64 && IA32_EMULATION ---help--- Include code to run binaries for the x32 native 32-bit ABI for 64-bit processors. An x32 process gets access to the full 64-bit register file and wide data path while leaving pointers at 32 bits for smaller memory footprint. You will need a recent binutils (2.22 or later) with elf32_x86_64 support enabled to compile a kernel with this option set. config COMPAT def_bool y depends on IA32_EMULATION || X86_X32 select ARCH_WANT_OLD_COMPAT_IPC if COMPAT config COMPAT_FOR_U64_ALIGNMENT def_bool y config SYSVIPC_COMPAT def_bool y depends on SYSVIPC config KEYS_COMPAT def_bool y depends on KEYS endif endmenu config HAVE_ATOMIC_IOMAP def_bool y depends on X86_32 config X86_DEV_DMA_OPS bool depends on X86_64 || STA2X11 config X86_DMA_REMAP bool depends on STA2X11 config IOSF_MBI bool depends on PCI ---help--- To be selected by modules requiring access to the Intel OnChip System Fabric (IOSF) Sideband MailBox Interface (MBI). For MBI platforms enumerable by PCI. source "net/Kconfig" source "drivers/Kconfig" source "drivers/firmware/Kconfig" source "fs/Kconfig" source "arch/x86/Kconfig.debug" source "security/Kconfig" source "crypto/Kconfig" source "arch/x86/kvm/Kconfig" source "lib/Kconfig"