blob: 8b444b94e92fde83967f032e0602fb7a68000a43 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
|
General Purpose I2C Bus Mux
This binding describes an I2C bus multiplexer that uses a mux controller
from the mux subsystem to route the I2C signals.
.-----. .-----.
| dev | | dev |
.------------. '-----' '-----'
| SoC | | |
| | .--------+--------'
| .------. | .------+ child bus A, on MUX value set to 0
| | I2C |-|--| Mux |
| '------' | '--+---+ child bus B, on MUX value set to 1
| .------. | | '----------+--------+--------.
| | MUX- | | | | | |
| | Ctrl |-|-----+ .-----. .-----. .-----.
| '------' | | dev | | dev | | dev |
'------------' '-----' '-----' '-----'
Required properties:
- compatible: i2c-mux
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
port is connected to.
- mux-controls: The phandle of the mux controller to use for operating the
mux.
* Standard I2C mux properties. See i2c-mux.txt in this directory.
* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number
is also the mux-controller state described in ../mux/mux-controller.txt
Optional properties:
- mux-locked: If present, explicitly allow unrelated I2C transactions on the
parent I2C adapter at these times:
+ during setup of the multiplexer
+ between setup of the multiplexer and the child bus I2C transaction
+ between the child bus I2C transaction and releasing of the multiplexer
+ during releasing of the multiplexer
However, I2C transactions to devices behind all I2C multiplexers connected
to the same parent adapter that this multiplexer is connected to are blocked
for the full duration of the complete multiplexed I2C transaction (i.e.
including the times covered by the above list).
If mux-locked is not present, the multiplexer is assumed to be parent-locked.
This means that no unrelated I2C transactions are allowed on the parent I2C
adapter for the complete multiplexed I2C transaction.
The properties of mux-locked and parent-locked multiplexers are discussed
in more detail in Documentation/i2c/i2c-topology.rst.
For each i2c child node, an I2C child bus will be created. They will
be numbered based on their order in the device tree.
Whenever an access is made to a device on a child bus, the value set
in the relevant node's reg property will be set as the state in the
mux controller.
Example:
mux: mux-controller {
compatible = "gpio-mux";
#mux-control-cells = <0>;
mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
<&pioA 1 GPIO_ACTIVE_HIGH>;
};
i2c-mux {
compatible = "i2c-mux";
mux-locked;
i2c-parent = <&i2c1>;
mux-controls = <&mux>;
#address-cells = <1>;
#size-cells = <0>;
i2c@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
ssd1307: oled@3c {
compatible = "solomon,ssd1307fb-i2c";
reg = <0x3c>;
pwms = <&pwm 4 3000>;
reset-gpios = <&gpio2 7 1>;
reset-active-low;
};
};
i2c@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
pca9555: pca9555@20 {
compatible = "nxp,pca9555";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
};
};
};
|
