1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
Device tree bindings for Texas instruments Davinci/Keystone NAND controller
This file provides information, what the device node for the davinci/keystone
NAND interface contains.
Documentation:
Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Required properties:
- compatible: "ti,davinci-nand"
"ti,keystone-nand"
- reg: Contains 2 offset/length values:
- offset and length for the access window.
- offset and length for accessing the AEMIF
control registers.
- ti,davinci-chipselect: number of chipselect. Indicates on the
davinci_nand driver which chipselect is used
for accessing the nand.
Can be in the range [0-3].
Recommended properties :
- ti,davinci-mask-ale: mask for ALE. Needed for executing address
phase. These offset will be added to the base
address for the chip select space the NAND Flash
device is connected to.
If not set equal to 0x08.
- ti,davinci-mask-cle: mask for CLE. Needed for executing command
phase. These offset will be added to the base
address for the chip select space the NAND Flash
device is connected to.
If not set equal to 0x10.
- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask
addresses for given chipselect.
- nand-ecc-mode: operation mode of the NAND ecc mode. ECC mode
valid values for davinci driver:
- "none"
- "soft"
- "hw"
- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
- nand-bus-width: buswidth 8 or 16. If not present 8.
- nand-on-flash-bbt: use flash based bad block table support. OOB
identifier is saved in OOB area. If not present
false.
Deprecated properties:
- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
valid values for davinci driver:
- "none"
- "soft"
- "hw"
- ti,davinci-nand-buswidth: buswidth 8 or 16. If not present 8.
- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
identifier is saved in OOB area. If not present
false.
Nand device bindings may contain additional sub-nodes describing partitions of
the address space. See partition.txt for more detail. The NAND Flash timing
values must be programmed in the chip select’s node of AEMIF
memory-controller (see Documentation/devicetree/bindings/memory-controllers/
davinci-aemif.txt).
Example(da850 EVM ):
nand_cs3@62000000 {
compatible = "ti,davinci-nand";
reg = <0x62000000 0x807ff
0x68000000 0x8000>;
ti,davinci-chipselect = <1>;
ti,davinci-mask-ale = <0>;
ti,davinci-mask-cle = <0>;
ti,davinci-mask-chipsel = <0>;
nand-ecc-mode = "hw";
ti,davinci-ecc-bits = <4>;
nand-on-flash-bbt;
partition@180000 {
label = "ubifs";
reg = <0x180000 0x7e80000>;
};
};
|
