1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
|
Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC)
The device node has following properties.
Required properties:
- compatible: should be "rockchip,<name>-gamc"
"rockchip,rk3128-gmac": found on RK312x SoCs
"rockchip,rk3228-gmac": found on RK322x SoCs
"rockchip,rk3288-gmac": found on RK3288 SoCs
"rockchip,rk3328-gmac": found on RK3328 SoCs
"rockchip,rk3366-gmac": found on RK3366 SoCs
"rockchip,rk3368-gmac": found on RK3368 SoCs
"rockchip,rk3399-gmac": found on RK3399 SoCs
"rockchip,rv1108-gmac": found on RV1108 SoCs
- reg: addresses and length of the register sets for the device.
- interrupts: Should contain the GMAC interrupts.
- interrupt-names: Should contain the interrupt names "macirq".
- rockchip,grf: phandle to the syscon grf used to control speed and mode.
- clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY.
<&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC
<&cru SCLK_MAC_RX>: clock gate for RX
<&cru SCLK_MAC_TX>: clock gate for TX
<&cru SCLK_MACREF>: clock gate for RMII referce clock
<&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output
<&cru ACLK_GMAC>: AXI clock gate for GMAC
<&cru PCLK_GMAC>: APB clock gate for GMAC
- clock-names: One name for each entry in the clocks property.
- phy-mode: See ethernet.txt file in the same directory.
- pinctrl-names: Names corresponding to the numbered pinctrl states.
- pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>.
- clock_in_out: For RGMII, it must be "input", means main clock(125MHz)
is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means
PHY provides the reference clock(50MHz), "output" means GMAC provides the
reference clock.
- snps,reset-gpio gpio number for phy reset.
- snps,reset-active-low boolean flag to indicate if phy reset is active low.
- assigned-clocks: main clock, should be <&cru SCLK_MAC>;
- assigned-clock-parents = parent of main clock.
can be <&ext_gmac> or <&cru SCLK_MAC_PLL>.
Optional properties:
- tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default.
- rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default.
- phy-supply: phandle to a regulator if the PHY needs one
Example:
gmac: ethernet@ff290000 {
compatible = "rockchip,rk3288-gmac";
reg = <0xff290000 0x10000>;
interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
rockchip,grf = <&grf>;
clocks = <&cru SCLK_MAC>,
<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
clock-names = "stmmaceth",
"mac_clk_rx", "mac_clk_tx",
"clk_mac_ref", "clk_mac_refout",
"aclk_mac", "pclk_mac";
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>;
clock_in_out = "input";
snps,reset-gpio = <&gpio4 7 0>;
snps,reset-active-low;
assigned-clocks = <&cru SCLK_MAC>;
assigned-clock-parents = <&ext_gmac>;
tx_delay = <0x30>;
rx_delay = <0x10>;
};
|
