aboutsummaryrefslogtreecommitdiff
path: root/Documentation/media/uapi/dvb/dvbproperty.rst
blob: 1a56c1724e595b849720c9f17b980fa01aec028b (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
.. -*- coding: utf-8; mode: rst -*-

.. _frontend-properties:

**************
Property types
**************

Tuning into a Digital TV physical channel and starting decoding it
requires changing a set of parameters, in order to control the tuner,
the demodulator, the Linear Low-noise Amplifier (LNA) and to set the
antenna subsystem via Satellite Equipment Control - SEC (on satellite
systems). The actual parameters are specific to each particular digital
TV standards, and may change as the digital TV specs evolves.

In the past (up to DVB API version 3 - DVBv3), the strategy used was to have a
union with the parameters needed to tune for DVB-S, DVB-C, DVB-T and
ATSC delivery systems grouped there. The problem is that, as the second
generation standards appeared, the size of such union was not big
enough to group the structs that would be required for those new
standards. Also, extending it would break userspace.

So, the legacy union/struct based approach was deprecated, in favor
of a properties set approach. On such approach,
:ref:`FE_GET_PROPERTY and FE_SET_PROPERTY <FE_GET_PROPERTY>` are used
to setup the frontend and read its status.

The actual action is determined by a set of dtv_property cmd/data pairs.
With one single ioctl, is possible to get/set up to 64 properties.

This section describes the new and recommended way to set the frontend,
with supports all digital TV delivery systems.

.. note::

   1. On Linux DVB API version 3, setting a frontend was done via
      struct :c:type:`dvb_frontend_parameters`.

   2. Don't use DVB API version 3 calls on hardware with supports
      newer standards. Such API provides no suport or a very limited
      support to new standards and/or new hardware.

   3. Nowadays, most frontends support multiple delivery systems.
      Only with DVB API version 5 calls it is possible to switch between
      the multiple delivery systems supported by a frontend.

   4. DVB API version 5 is also called *S2API*, as the first
      new standard added to it was DVB-S2.

**Example**: in order to set the hardware to tune into a DVB-C channel
at 651 kHz, modulated with 256-QAM, FEC 3/4 and symbol rate of 5.217
Mbauds, those properties should be sent to
:ref:`FE_SET_PROPERTY <FE_GET_PROPERTY>` ioctl:

  :ref:`DTV_DELIVERY_SYSTEM <DTV-DELIVERY-SYSTEM>` = SYS_DVBC_ANNEX_A

  :ref:`DTV_FREQUENCY <DTV-FREQUENCY>` = 651000000

  :ref:`DTV_MODULATION <DTV-MODULATION>` = QAM_256

  :ref:`DTV_INVERSION <DTV-INVERSION>` = INVERSION_AUTO

  :ref:`DTV_SYMBOL_RATE <DTV-SYMBOL-RATE>` = 5217000

  :ref:`DTV_INNER_FEC <DTV-INNER-FEC>` = FEC_3_4

  :ref:`DTV_TUNE <DTV-TUNE>`

The code that would that would do the above is show in
:ref:`dtv-prop-example`.

.. code-block:: c
    :caption: Example: Setting digital TV frontend properties
    :name: dtv-prop-example

    #include <stdio.h>
    #include <fcntl.h>
    #include <sys/ioctl.h>
    #include <linux/dvb/frontend.h>

    static struct dtv_property props[] = {
	{ .cmd = DTV_DELIVERY_SYSTEM, .u.data = SYS_DVBC_ANNEX_A },
	{ .cmd = DTV_FREQUENCY,       .u.data = 651000000 },
	{ .cmd = DTV_MODULATION,      .u.data = QAM_256 },
	{ .cmd = DTV_INVERSION,       .u.data = INVERSION_AUTO },
	{ .cmd = DTV_SYMBOL_RATE,     .u.data = 5217000 },
	{ .cmd = DTV_INNER_FEC,       .u.data = FEC_3_4 },
	{ .cmd = DTV_TUNE }
    };

    static struct dtv_properties dtv_prop = {
	.num = 6, .props = props
    };

    int main(void)
    {
	int fd = open("/dev/dvb/adapter0/frontend0", O_RDWR);

	if (!fd) {
	    perror ("open");
	    return -1;
	}
	if (ioctl(fd, FE_SET_PROPERTY, &dtv_prop) == -1) {
	    perror("ioctl");
	    return -1;
	}
	printf("Frontend set\\n");
	return 0;
    }

.. attention:: While it is possible to directly call the Kernel code like the
   above example, it is strongly recommended to use
   `libdvbv5 <https://linuxtv.org/docs/libdvbv5/index.html>`__, as it
   provides abstraction to work with the supported digital TV standards and
   provides methods for usual operations like program scanning and to
   read/write channel descriptor files.

.. toctree::
    :maxdepth: 1

    fe_property_parameters
    frontend-stat-properties
    frontend-property-terrestrial-systems
    frontend-property-cable-systems
    frontend-property-satellite-systems
    frontend-header