1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
|
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef _RAID10_H
#define _RAID10_H
/* Note: raid10_info.rdev can be set to NULL asynchronously by
* raid10_remove_disk.
* There are three safe ways to access raid10_info.rdev.
* 1/ when holding mddev->reconfig_mutex
* 2/ when resync/recovery/reshape is known to be happening - i.e. in code
* that is called as part of performing resync/recovery/reshape.
* 3/ while holding rcu_read_lock(), use rcu_dereference to get the pointer
* and if it is non-NULL, increment rdev->nr_pending before dropping the
* RCU lock.
* When .rdev is set to NULL, the nr_pending count checked again and if it has
* been incremented, the pointer is put back in .rdev.
*/
struct raid10_info {
struct md_rdev *rdev, *replacement;
sector_t head_position;
int recovery_disabled; /* matches
* mddev->recovery_disabled
* when we shouldn't try
* recovering this device.
*/
};
struct r10conf {
struct mddev *mddev;
struct raid10_info *mirrors;
struct raid10_info *mirrors_new, *mirrors_old;
spinlock_t device_lock;
/* geometry */
struct geom {
int raid_disks;
int near_copies; /* number of copies laid out
* raid0 style */
int far_copies; /* number of copies laid out
* at large strides across drives
*/
int far_offset; /* far_copies are offset by 1
* stripe instead of many
*/
sector_t stride; /* distance between far copies.
* This is size / far_copies unless
* far_offset, in which case it is
* 1 stripe.
*/
int far_set_size; /* The number of devices in a set,
* where a 'set' are devices that
* contain far/offset copies of
* each other.
*/
int chunk_shift; /* shift from chunks to sectors */
sector_t chunk_mask;
} prev, geo;
int copies; /* near_copies * far_copies.
* must be <= raid_disks
*/
sector_t dev_sectors; /* temp copy of
* mddev->dev_sectors */
sector_t reshape_progress;
sector_t reshape_safe;
unsigned long reshape_checkpoint;
sector_t offset_diff;
struct list_head retry_list;
/* A separate list of r1bio which just need raid_end_bio_io called.
* This mustn't happen for writes which had any errors if the superblock
* needs to be written.
*/
struct list_head bio_end_io_list;
/* queue pending writes and submit them on unplug */
struct bio_list pending_bio_list;
int pending_count;
spinlock_t resync_lock;
atomic_t nr_pending;
int nr_waiting;
int nr_queued;
int barrier;
int array_freeze_pending;
sector_t next_resync;
int fullsync; /* set to 1 if a full sync is needed,
* (fresh device added).
* Cleared when a sync completes.
*/
int have_replacement; /* There is at least one
* replacement device.
*/
wait_queue_head_t wait_barrier;
mempool_t r10bio_pool;
mempool_t r10buf_pool;
struct page *tmppage;
struct bio_set bio_split;
/* When taking over an array from a different personality, we store
* the new thread here until we fully activate the array.
*/
struct md_thread *thread;
/*
* Keep track of cluster resync window to send to other nodes.
*/
sector_t cluster_sync_low;
sector_t cluster_sync_high;
};
/*
* this is our 'private' RAID10 bio.
*
* it contains information about what kind of IO operations were started
* for this RAID10 operation, and about their status:
*/
struct r10bio {
atomic_t remaining; /* 'have we finished' count,
* used from IRQ handlers
*/
sector_t sector; /* virtual sector number */
int sectors;
unsigned long state;
unsigned long start_time;
struct mddev *mddev;
/*
* original bio going to /dev/mdx
*/
struct bio *master_bio;
/*
* if the IO is in READ direction, then this is where we read
*/
int read_slot;
struct list_head retry_list;
/*
* if the IO is in WRITE direction, then multiple bios are used,
* one for each copy.
* When resyncing we also use one for each copy.
* When reconstructing, we use 2 bios, one for read, one for write.
* We choose the number when they are allocated.
* We sometimes need an extra bio to write to the replacement.
*/
struct r10dev {
struct bio *bio;
union {
struct bio *repl_bio; /* used for resync and
* writes */
struct md_rdev *rdev; /* used for reads
* (read_slot >= 0) */
};
sector_t addr;
int devnum;
} devs[];
};
/* bits for r10bio.state */
enum r10bio_state {
R10BIO_Uptodate,
R10BIO_IsSync,
R10BIO_IsRecover,
R10BIO_IsReshape,
R10BIO_Degraded,
/* Set ReadError on bios that experience a read error
* so that raid10d knows what to do with them.
*/
R10BIO_ReadError,
/* If a write for this request means we can clear some
* known-bad-block records, we set this flag.
*/
R10BIO_MadeGood,
R10BIO_WriteError,
/* During a reshape we might be performing IO on the
* 'previous' part of the array, in which case this
* flag is set
*/
R10BIO_Previous,
/* failfast devices did receive failfast requests. */
R10BIO_FailFast,
R10BIO_Discard,
};
#endif
|
