From 23397775bc2b1ff35d4eee075ef53e16360859dc Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Tue, 9 Feb 2021 21:42:51 -0500 Subject: ppc: Remove MPC8544DS board This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove this board. Cc: Priyanka Jain Signed-off-by: Tom Rini Reviewed-by: Priyanka Jain --- arch/powerpc/cpu/mpc85xx/Kconfig | 6 - board/freescale/common/pixis.h | 27 --- board/freescale/mpc8544ds/Kconfig | 12 - board/freescale/mpc8544ds/MAINTAINERS | 6 - board/freescale/mpc8544ds/Makefile | 10 - board/freescale/mpc8544ds/README | 122 ---------- board/freescale/mpc8544ds/ddr.c | 56 ----- board/freescale/mpc8544ds/law.c | 17 -- board/freescale/mpc8544ds/mpc8544ds.c | 321 -------------------------- board/freescale/mpc8544ds/tlb.c | 74 ------ configs/MPC8544DS_defconfig | 52 ----- include/configs/MPC8544DS.h | 408 ---------------------------------- 12 files changed, 1111 deletions(-) delete mode 100644 board/freescale/mpc8544ds/Kconfig delete mode 100644 board/freescale/mpc8544ds/MAINTAINERS delete mode 100644 board/freescale/mpc8544ds/Makefile delete mode 100644 board/freescale/mpc8544ds/README delete mode 100644 board/freescale/mpc8544ds/ddr.c delete mode 100644 board/freescale/mpc8544ds/law.c delete mode 100644 board/freescale/mpc8544ds/mpc8544ds.c delete mode 100644 board/freescale/mpc8544ds/tlb.c delete mode 100644 configs/MPC8544DS_defconfig delete mode 100644 include/configs/MPC8544DS.h diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index c1a37706710..28c9f113d3f 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -52,11 +52,6 @@ config TARGET_MPC8541CDS bool "Support MPC8541CDS" select ARCH_MPC8541 -config TARGET_MPC8544DS - bool "Support MPC8544DS" - select ARCH_MPC8544 - imply PANIC_HANG - config TARGET_MPC8548CDS bool "Support MPC8548CDS" select ARCH_MPC8548 @@ -1443,7 +1438,6 @@ config SYS_FSL_LBC_CLK_DIV source "board/freescale/corenet_ds/Kconfig" source "board/freescale/mpc8541cds/Kconfig" -source "board/freescale/mpc8544ds/Kconfig" source "board/freescale/mpc8548cds/Kconfig" source "board/freescale/mpc8555cds/Kconfig" source "board/freescale/mpc8568mds/Kconfig" diff --git a/board/freescale/common/pixis.h b/board/freescale/common/pixis.h index 40053c45bb7..f468e6cc93c 100644 --- a/board/freescale/common/pixis.h +++ b/board/freescale/common/pixis.h @@ -45,33 +45,6 @@ typedef struct pixis { u8 res2[4]; } __attribute__ ((packed)) pixis_t; -#elif defined(CONFIG_TARGET_MPC8544DS) -typedef struct pixis { - u8 id; - u8 ver; - u8 pver; - u8 csr; - u8 rst; - u8 pwr; - u8 aux1; - u8 spd; - u8 res[8]; - u8 vctl; - u8 vstat; - u8 vcfgen0; - u8 vcfgen1; - u8 vcore0; - u8 res1; - u8 vboot; - u8 vspeed[2]; - u8 vclkh; - u8 vclkl; - u8 watch; - u8 led; - u8 vspeed2; - u8 res2[34]; -} __attribute__ ((packed)) pixis_t; - #elif defined(CONFIG_TARGET_MPC8572DS) typedef struct pixis { u8 id; diff --git a/board/freescale/mpc8544ds/Kconfig b/board/freescale/mpc8544ds/Kconfig deleted file mode 100644 index c3e25b89a02..00000000000 --- a/board/freescale/mpc8544ds/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_MPC8544DS - -config SYS_BOARD - default "mpc8544ds" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "MPC8544DS" - -endif diff --git a/board/freescale/mpc8544ds/MAINTAINERS b/board/freescale/mpc8544ds/MAINTAINERS deleted file mode 100644 index 74e7249e473..00000000000 --- a/board/freescale/mpc8544ds/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MPC8544DS BOARD -M: Priyanka Jain -S: Maintained -F: board/freescale/mpc8544ds/ -F: include/configs/MPC8544DS.h -F: configs/MPC8544DS_defconfig diff --git a/board/freescale/mpc8544ds/Makefile b/board/freescale/mpc8544ds/Makefile deleted file mode 100644 index 1693ae84330..00000000000 --- a/board/freescale/mpc8544ds/Makefile +++ /dev/null @@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright 2007 Freescale Semiconductor, Inc. -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. - -obj-y += mpc8544ds.o -obj-y += ddr.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/mpc8544ds/README b/board/freescale/mpc8544ds/README deleted file mode 100644 index b49c3c07c40..00000000000 --- a/board/freescale/mpc8544ds/README +++ /dev/null @@ -1,122 +0,0 @@ -Overview --------- -The MPC8544DS system is similar to the 85xx CDS systems such -as the MPC8548CDS due to the similar E500 core. However, it -is placed on the same board as the 8641 HPCN system. - - -Flash Banks ------------ -Like the 85xx CDS systems, the 8544 DS board has two flash banks. -They are both present on boot, but there locations can be swapped -using the dip-switch SW10, bit 2. - -However, unlike the CDS systems, but similar to the 8641 HPCN -board, a runtime reset through the FPGA can also affect a swap -on the flash bank mappings for the next reset cycle. - -Irrespective of the switch SW10[2], booting is always from the -boot bank at 0xfff8_0000. - - -Memory Map ----------- - -0xff80_0000 - 0xffbf_ffff Alternate bank 4MB -0xffc0_0000 - 0xffff_ffff Boot bank 4MB - -0xffb8_0000 Alternate image start 512KB -0xfff8_0000 Boot image start 512KB - - -Flashing Images ---------------- - -For example, to place a new image in the alternate flash bank -and then reset with that new image temporarily, use this: - - tftp 1000000 u-boot.bin.8544ds - erase ffb80000 ffbfffff - cp.b 1000000 ffb80000 80000 - pixis_reset altbank - - -To overwrite the image in the boot flash bank: - - tftp 1000000 u-boot.bin.8544ds - protect off all - erase fff80000 ffffffff - cp.b 1000000 fff80000 80000 - -Other example U-Boot image and flash manipulations examples -can be found in the README.mpc85xxcds file as well. - - -The pixis_reset command ------------------------ -A new command, "pixis_reset", is introduced to reset mpc8641hpcn board -using the FPGA sequencer. When the board restarts, it has the option -of using either the current or alternate flash bank as the boot -image, with or without the watchdog timer enabled, and finally with -or without frequency changes. - -Usage is; - - pixis_reset - pixis_reset altbank - pixis_reset altbank wd - pixis_reset altbank cf - pixis_reset cf - -Examples; - - /* reset to current bank, like "reset" command */ - pixis_reset - - /* reset board but use the to alternate flash bank */ - pixis_reset altbank - - /* reset board, use alternate flash bank with watchdog timer enabled*/ - pixis_reset altbank wd - - /* reset board to alternate bank with frequency changed. - * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio - */ - pixis-reset altbank cf 40 2.5 10 - -Valid clock choices are in the 8641 Reference Manuals. - - -Using the Device Tree Source File ---------------------------------- -To create the DTB (Device Tree Binary) image file, -use a command similar to this: - - dtc -b 0 -f -I dts -O dtb mpc8544ds.dts > mpc8544ds.dtb - -Likely, that .dts file will come from here; - - linux-2.6/arch/powerpc/boot/dts/mpc8544ds.dts - -After placing the DTB file in your TFTP disk area, -you can download that dtb file using a command like: - - tftp 900000 mpc8544ds.dtb - -Burn it to flash if you want. - - -Booting Linux -------------- - -Place a linux uImage in the TFTP disk area too. - - tftp 1000000 uImage.8544 - tftp 900000 mpc8544ds.dtb - bootm 1000000 - 900000 - -Watch your ethact, netdev and bootargs U-Boot environment variables. -You may want to do something like this too: - - setenv ethact eTSEC3 - setenv netdev eth1 diff --git a/board/freescale/mpc8544ds/ddr.c b/board/freescale/mpc8544ds/ddr.c deleted file mode 100644 index c4d985347b3..00000000000 --- a/board/freescale/mpc8544ds/ddr.c +++ /dev/null @@ -1,56 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2008 Freescale Semiconductor, Inc. - */ - -#include - -#include -#include - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - /* - * Factors to consider for clock adjust: - * - number of chips on bus - * - position of slot - * - DDR1 vs. DDR2? - * - ??? - * - * This needs to be determined on a board-by-board basis. - * 0110 3/4 cycle late - * 0111 7/8 cycle late - */ - popts->clk_adjust = 7; - - /* - * Factors to consider for CPO: - * - frequency - * - ddr1 vs. ddr2 - */ - popts->cpo_override = 10; - - /* - * Factors to consider for write data delay: - * - number of DIMMs - * - * 1 = 1/4 clock delay - * 2 = 1/2 clock delay - * 3 = 3/4 clock delay - * 4 = 1 clock delay - * 5 = 5/4 clock delay - * 6 = 3/2 clock delay - */ - popts->write_data_delay = 3; - - /* 2T timing enable */ - popts->twot_en = 1; - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; -} diff --git a/board/freescale/mpc8544ds/law.c b/board/freescale/mpc8544ds/law.c deleted file mode 100644 index 52cec7fbb59..00000000000 --- a/board/freescale/mpc8544ds/law.c +++ /dev/null @@ -1,17 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008, 2010 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include -#include - -struct law_entry law_table[] = { - SET_LAW(CONFIG_SYS_LBC_NONCACHE_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC), -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c deleted file mode 100644 index 30ed7083657..00000000000 --- a/board/freescale/mpc8544ds/mpc8544ds.c +++ /dev/null @@ -1,321 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2007,2009-2010 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "../common/sgmii_riser.h" - -int checkboard (void) -{ - volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; - volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR); - u8 vboot; - u8 *pixis_base = (u8 *)PIXIS_BASE; - - if ((uint)&gur->porpllsr != 0xe00e0000) { - printf("immap size error %lx\n",(ulong)&gur->porpllsr); - } - printf ("Board: MPC8544DS, Sys ID: 0x%02x, " - "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", - in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER), - in_8(pixis_base + PIXIS_PVER)); - - vboot = in_8(pixis_base + PIXIS_VBOOT); - if (vboot & PIXIS_VBOOT_FMAP) - printf ("vBank: %d\n", ((vboot & PIXIS_VBOOT_FBANK) >> 6)); - else - puts ("Promjet\n"); - - lbc->ltesr = 0xffffffff; /* Clear LBC error interrupts */ - lbc->lteir = 0xffffffff; /* Enable LBC error interrupts */ - ecm->eedr = 0xffffffff; /* Clear ecm errors */ - ecm->eeer = 0xffffffff; /* Enable ecm errors */ - - return 0; -} - -#ifdef CONFIG_PCI1 -static struct pci_controller pci1_hose; -#endif - -#ifdef CONFIG_PCIE3 -static struct pci_controller pcie3_hose; -#endif - -void pci_init_board(void) -{ - volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - struct fsl_pci_info pci_info; - u32 devdisr, pordevsr, io_sel; - u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel; - int first_free_busno = 0; - - int pcie_ep, pcie_configured; - - devdisr = in_be32(&gur->devdisr); - pordevsr = in_be32(&gur->pordevsr); - porpllsr = in_be32(&gur->porpllsr); - io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; - - debug (" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel); - - puts("\n"); - -#ifdef CONFIG_PCIE3 - pcie_configured = is_serdes_configured(PCIE3); - - if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE3)){ - /* contains both PCIE3 MEM & IO space */ - set_next_law(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_4M, - LAW_TRGT_IF_PCIE_3); - SET_STD_PCIE_INFO(pci_info, 3); - pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info.regs); - - /* outbound memory */ - pci_set_region(&pcie3_hose.regions[0], - CONFIG_SYS_PCIE3_MEM_BUS2, - CONFIG_SYS_PCIE3_MEM_PHYS2, - CONFIG_SYS_PCIE3_MEM_SIZE2, - PCI_REGION_MEM); - - pcie3_hose.region_count = 1; - - printf("PCIE3: connected to ULI as %s (base addr %lx)\n", - pcie_ep ? "Endpoint" : "Root Complex", - pci_info.regs); - first_free_busno = fsl_pci_init_port(&pci_info, - &pcie3_hose, first_free_busno); - - /* - * Activate ULI1575 legacy chip by performing a fake - * memory access. Needed to make ULI RTC work. - */ - in_be32((u32 *)CONFIG_SYS_PCIE3_MEM_BUS); - } else { - printf("PCIE3: disabled\n"); - } - puts("\n"); -#else - setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE3); /* disable */ -#endif - -#ifdef CONFIG_PCIE1 - SET_STD_PCIE_INFO(pci_info, 1); - first_free_busno = fsl_pcie_init_ctrl(first_free_busno, devdisr, PCIE1, &pci_info); -#else - setbits_be32(&gur->devdisr, _DEVDISR_PCIE1); /* disable */ -#endif - -#ifdef CONFIG_PCIE2 - SET_STD_PCIE_INFO(pci_info, 2); - first_free_busno = fsl_pcie_init_ctrl(first_free_busno, devdisr, PCIE2, &pci_info); -#else - setbits_be32(&gur->devdisr, _DEVDISR_PCIE2); /* disable */ -#endif - -#ifdef CONFIG_PCI1 - pci_speed = 66666000; - pci_32 = 1; - pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; - pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; - - if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { - SET_STD_PCI_INFO(pci_info, 1); - set_next_law(pci_info.mem_phys, - law_size_bits(pci_info.mem_size), pci_info.law); - set_next_law(pci_info.io_phys, - law_size_bits(pci_info.io_size), pci_info.law); - - pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs); - printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n", - (pci_32) ? 32 : 64, - (pci_speed == 33333000) ? "33" : - (pci_speed == 66666000) ? "66" : "unknown", - pci_clk_sel ? "sync" : "async", - pci_agent ? "agent" : "host", - pci_arb ? "arbiter" : "external-arbiter", - pci_info.regs); - - first_free_busno = fsl_pci_init_port(&pci_info, - &pci1_hose, first_free_busno); - } else { - printf("PCI: disabled\n"); - } - - puts("\n"); -#else - setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */ -#endif -} - -int last_stage_init(void) -{ - return 0; -} - - -unsigned long -get_board_sys_clk(ulong dummy) -{ - u8 i, go_bit, rd_clks; - ulong val = 0; - u8 *pixis_base = (u8 *)PIXIS_BASE; - - go_bit = in_8(pixis_base + PIXIS_VCTL); - go_bit &= 0x01; - - rd_clks = in_8(pixis_base + PIXIS_VCFGEN0); - rd_clks &= 0x1C; - - /* - * Only if both go bit and the SCLK bit in VCFGEN0 are set - * should we be using the AUX register. Remember, we also set the - * GO bit to boot from the alternate bank on the on-board flash - */ - - if (go_bit) { - if (rd_clks == 0x1c) - i = in_8(pixis_base + PIXIS_AUX); - else - i = in_8(pixis_base + PIXIS_SPD); - } else { - i = in_8(pixis_base + PIXIS_SPD); - } - - i &= 0x07; - - switch (i) { - case 0: - val = 33333333; - break; - case 1: - val = 40000000; - break; - case 2: - val = 50000000; - break; - case 3: - val = 66666666; - break; - case 4: - val = 83000000; - break; - case 5: - val = 100000000; - break; - case 6: - val = 133333333; - break; - case 7: - val = 166666666; - break; - } - - return val; -} - - -#define MIIM_CIS8204_SLED_CON 0x1b -#define MIIM_CIS8204_SLEDCON_INIT 0x1115 -/* - * Hack to write all 4 PHYs with the LED values - */ -int board_phy_config(struct phy_device *phydev) -{ - static int do_once; - uint phyid; - struct mii_dev *bus = phydev->bus; - - if (phydev->drv->config) - phydev->drv->config(phydev); - if (do_once) - return 0; - - for (phyid = 0; phyid < 4; phyid++) - bus->write(bus, phyid, MDIO_DEVAD_NONE, MIIM_CIS8204_SLED_CON, - MIIM_CIS8204_SLEDCON_INIT); - - do_once = 1; - - return 0; -} - - -int board_eth_init(struct bd_info *bis) -{ -#ifdef CONFIG_TSEC_ENET - struct fsl_pq_mdio_info mdio_info; - struct tsec_info_struct tsec_info[2]; - int num = 0; - -#ifdef CONFIG_TSEC1 - SET_STD_TSEC_INFO(tsec_info[num], 1); - if (is_serdes_configured(SGMII_TSEC1)) { - puts("eTSEC1 is in sgmii mode.\n"); - tsec_info[num].flags |= TSEC_SGMII; - } - num++; -#endif -#ifdef CONFIG_TSEC3 - SET_STD_TSEC_INFO(tsec_info[num], 3); - if (is_serdes_configured(SGMII_TSEC3)) { - puts("eTSEC3 is in sgmii mode.\n"); - tsec_info[num].flags |= TSEC_SGMII; - } - num++; -#endif - - if (!num) { - printf("No TSECs initialized\n"); - - return 0; - } - - if (is_serdes_configured(SGMII_TSEC1) || - is_serdes_configured(SGMII_TSEC3)) { - fsl_sgmii_riser_init(tsec_info, num); - } - - mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; - mdio_info.name = DEFAULT_MII_NAME; - fsl_pq_mdio_init(bis, &mdio_info); - - tsec_eth_init(bis, tsec_info, num); -#endif - return pci_eth_init(bis); -} - -#if defined(CONFIG_OF_BOARD_SETUP) -int ft_board_setup(void *blob, struct bd_info *bd) -{ - ft_cpu_setup(blob, bd); - - FT_FSL_PCI_SETUP; - -#ifdef CONFIG_FSL_SGMII_RISER - fsl_sgmii_riser_fdt_fixup(blob); -#endif - - return 0; -} -#endif diff --git a/board/freescale/mpc8544ds/tlb.c b/board/freescale/mpc8544ds/tlb.c deleted file mode 100644 index 7bd462934aa..00000000000 --- a/board/freescale/mpc8544ds/tlb.c +++ /dev/null @@ -1,74 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - /* - * TLB 0: 64M Non-cacheable, guarded - * 0xfc000000 64M Covers FLASH at 0xFE800000 and 0xFF800000 - * Out of reset this entry is only 4K. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_BOOT_BLOCK, CONFIG_SYS_BOOT_BLOCK, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_64M, 1), - /* - * TLB 1: 1G Non-cacheable, guarded - * 0x80000000 1G PCIE 8,9,a,b - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE_VIRT, CONFIG_SYS_PCIE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_1G, 1), - - /* - * TLB 2: 256M Non-cacheable, guarded - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCI_VIRT, CONFIG_SYS_PCI_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - - /* - * TLB 3: 256M Non-cacheable, guarded - */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCI_VIRT + 0x10000000, CONFIG_SYS_PCI_PHYS + 0x10000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_256M, 1), - - /* - * TLB 4: 64M Non-cacheable, guarded - * 0xe000_0000 1M CCSRBAR - * 0xe100_0000 255M PCI IO range - */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_64M, 1), - - /* - * TLB 5: 64M Non-cacheable, guarded - * 0xf8000000 64M PIXIS 0xF8000000 - 0xFBFFFFFF - */ - SET_TLB_ENTRY(1, CONFIG_SYS_LBC_NONCACHE_BASE, CONFIG_SYS_LBC_NONCACHE_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_64M, 1), -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/MPC8544DS_defconfig b/configs/MPC8544DS_defconfig deleted file mode 100644 index 82f14d81226..00000000000 --- a/configs/MPC8544DS_defconfig +++ /dev/null @@ -1,52 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xFFF80000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_MPC85xx=y -# CONFIG_CMD_ERRATA is not set -CONFIG_TARGET_MPC8544DS=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -# CONFIG_CONSOLE_MUX is not set -# CONFIG_MISC_INIT_R is not set -CONFIG_HUSH_PARSER=y -CONFIG_CMD_REGINFO=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -# CONFIG_CMD_HASH is not set -CONFIG_CMD_EXT2=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xFFF70000 -CONFIG_SCSI_AHCI=y -# CONFIG_MMC is not set -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_PHY_ATHEROS=y -CONFIG_PHY_BROADCOM=y -CONFIG_PHY_DAVICOM=y -CONFIG_PHY_LXT=y -CONFIG_PHY_MARVELL=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_SMSC=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_MII=y -CONFIG_RTL8139=y -CONFIG_TSEC_ENET=y -CONFIG_SCSI=y -CONFIG_SYS_NS16550=y -CONFIG_USB=y -CONFIG_USB_EHCI_PCI=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h deleted file mode 100644 index f4f41da4988..00000000000 --- a/include/configs/MPC8544DS.h +++ /dev/null @@ -1,408 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc. - */ - -/* - * mpc8544ds board configuration file - * - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PCI1 1 /* PCI controller 1 */ -#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */ -#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */ -#define CONFIG_PCIE3 1 /* PCIE controller 3 (ULI bridge) */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ - -#ifndef __ASSEMBLY__ -#include -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -/* - * Only possible on E500 Version 2 or newer cores. - */ -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD - -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ - -/* Make sure required options are set */ -#ifndef CONFIG_SPD_EEPROM -#error ("CONFIG_SPD_EEPROM is required") -#endif - -/* - * Memory map - * - * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable - * - * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable - * - * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable - * - * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable - * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable - * - * Localbus cacheable - * - * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable - * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0 - * - * Localbus non-cacheable - * - * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable - * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable - * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable - * - */ - -/* - * Local Bus Definitions - */ -#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */ - -#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ - -#define CONFIG_SYS_BR0_PRELIM 0xff801001 -#define CONFIG_SYS_BR1_PRELIM 0xfe801001 - -#define CONFIG_SYS_OR0_PRELIM 0xff806e65 -#define CONFIG_SYS_OR1_PRELIM 0xff806e65 - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} - -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000 - -#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */ -#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ - -#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */ -#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ - -#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ -#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ -#define PIXIS_ID 0x0 /* Board ID at offset 0 */ -#define PIXIS_VER 0x1 /* Board version at offset 1 */ -#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ -#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ -#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch - * register */ -#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ -#define PIXIS_VCTL 0x10 /* VELA Control Register */ -#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ -#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ -#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ -#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ -#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ -#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ -#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ -#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ -#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */ -#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ -#define PIXIS_VSPEED2_TSEC1SER 0x2 -#define PIXIS_VSPEED2_TSEC3SER 0x1 -#define PIXIS_VCFGEN1_TSEC1SER 0x20 -#define PIXIS_VCFGEN1_TSEC3SER 0x40 -#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER) -#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER) - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* Serial Port - controlled on board with jumper J8 - * open - index 2 - * shorted - index 1 - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */ -#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ -#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */ -#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ - -#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ - -/* controller 2, Slot 1, tgtid 1, Base address 9000 */ -#define CONFIG_SYS_PCIE2_NAME "Slot 1" -#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ - -/* controller 1, Slot 2,tgtid 2, Base address a000 */ -#define CONFIG_SYS_PCIE1_NAME "Slot 2" -#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -/* controller 3, direct to uli, tgtid 3, Base address b000 */ -#define CONFIG_SYS_PCIE3_NAME "ULI" -#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */ -#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */ -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */ -#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000 -#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000 -#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000 -#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */ - -#if defined(CONFIG_PCI) - -/*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT - -/*PCI video card used*/ -/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ - -/* video */ - -#if defined(CONFIG_VIDEO) -#define CONFIG_BIOSEMU -#define CONFIG_ATI_RADEON_FB -#define CONFIG_VIDEO_LOGO -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET -#endif - - -#ifndef CONFIG_PCI_PNP - #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS - #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS - #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ -#endif - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#ifdef CONFIG_SCSI_AHCI -#define CONFIG_SATA_ULI5288 -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) -#endif /* CONFIG_SCSI_AHCI */ - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" - -#define CONFIG_PIXIS_SGMII_CMD -#define CONFIG_FSL_SGMII_RISER 1 -#define SGMII_RISER_PHY_OFFSET 0x1c - -#define TSEC1_PHY_ADDR 0 -#define TSEC3_PHY_ADDR 1 - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 -#define TSEC3_PHYIDX 0 - -#define CONFIG_ETHPRIME "eTSEC1" -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * USB - */ - -#ifdef CONFIG_USB_EHCI_HCD -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_PCI_EHCI_DEVICE 0 -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_IPADDR 192.168.1.251 - -#define CONFIG_HOSTNAME "8544ds_unknown" -#define CONFIG_ROOTPATH "/nfs/mpc85xx" -#define CONFIG_BOOTFILE "8544ds/uImage.uboot" -#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */ - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.0.0 - -#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ - -#define CONFIG_EXTRA_ENV_SETTINGS \ -"netdev=eth0\0" \ -"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ -"tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ -"consoledev=ttyS0\0" \ -"ramdiskaddr=2000000\0" \ -"ramdiskfile=8544ds/ramdisk.uboot\0" \ -"fdtaddr=1e00000\0" \ -"fdtfile=8544ds/mpc8544ds.dtb\0" \ -"bdev=sda3\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#endif /* __CONFIG_H */ -- cgit v1.2.3