| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 1be1b23696b3d4b0231c694f5e0767b4471d33a9 ]
The I2C_DETECT register is at IO port 0x1a7, which is outside the range
passed to devm_ioport_map() for io_base, and was only working because
there aren't actually any bounds checks for IO port accesses.
Extending the range does not seem like a good solution here, as it would
then conflict with the IO resource assigned to the I2C controller. As
this is just a one-off access during probe, use a simple inb() instead.
While we're at it, drop the unused define TQMX86_REG_I2C_INT_EN.
Fixes: 2f17dd34ffed ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/e8300a30f0791afb67d79db8089fb6004855f378.1676892223.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
mtk_thermal_probe
[ Upstream commit f05c7b7d9ea9477fcc388476c6f4ade8c66d2d26 ]
Smatch reports:
1. mtk_thermal_probe() warn: 'apmixed_base' from of_iomap() not released.
2. mtk_thermal_probe() warn: 'auxadc_base' from of_iomap() not released.
The original code forgets to release iomap resource when handling errors,
fix it by switch to devm_of_iomap.
Fixes: 89945047b166 ("thermal: mediatek: Add tsensor support for V2 thermal system")
Signed-off-by: Kang Chen <void0red@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230419020749.621257-1-void0red@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7badd752de05312fdb1aeb388480f706d0c087f ]
In the past setting the pin direction called pinctrl_gpio_direction()
which uses a mutex to serialize this. That was changed to set the
direction directly in the pin controller driver, but that lost the
serialization mechanism. Since the direction of multiple pins are in
the same register you can have a race condition, something that was
in fact observed with the cec-gpio driver.
Add a new spinlock to serialize writing to the FSEL registers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 1a4541b68e25 ("pinctrl-bcm2835: don't call pinctrl_gpio_direction()")
Link: https://lore.kernel.org/r/4302b66b-ca20-0f19-d2aa-ee8661118863@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f8435befd81dd85b7b610598551fadf675849bc1 ]
Do not global enable all the cyclic channels in at_xdmac_resume(). Instead
save the global status in at_xdmac_suspend() and re-enable the cyclic
channel only if it was active before suspend.
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230214151827.1050280-6-claudiu.beznea@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 970b17dfe264a9085ba4e593730ecfd496b950ab ]
The issue_pending request is ignored while driver is processing a DMA
request. Fix to issue the pending requests on any dma channel status.
Fixes: e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Link: https://lore.kernel.org/r/20230411101758.438472-2-mie@igel.co.jp
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a251994a441ee0a69ba7062c8cd2d08ead3db379 ]
The dw-edma driver stops after processing a DMA request even if a request
remains in the issued queue, which is not the expected behavior. The DMA
engine API requires continuous processing.
Add a trigger to start after one processing finished if there are requests
remain.
Fixes: e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Link: https://lore.kernel.org/r/20230411101758.438472-1-mie@igel.co.jp
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91d6a468e335571f1e67e046050dea9af5fa4ebe ]
gpi_ch_init() doesn't lock the ctrl_lock mutex, so there is no need to
unlock it too. Instead the mutex is handled by the function
gpi_alloc_chan_resources(), which properly locks and unlocks the mutex.
=====================================
WARNING: bad unlock balance detected!
6.3.0-rc5-00253-g99792582ded1-dirty #15 Not tainted
-------------------------------------
kworker/u16:0/9 is trying to release lock (&gpii->ctrl_lock) at:
[<ffffb99d04e1284c>] gpi_alloc_chan_resources+0x108/0x5bc
but there are no more locks to release!
other info that might help us debug this:
6 locks held by kworker/u16:0/9:
#0: ffff575740010938 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x220/0x594
#1: ffff80000809bdd0 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work+0x220/0x594
#2: ffff575740f2a0f8 (&dev->mutex){....}-{3:3}, at: __device_attach+0x38/0x188
#3: ffff57574b5570f8 (&dev->mutex){....}-{3:3}, at: __device_attach+0x38/0x188
#4: ffffb99d06a2f180 (of_dma_lock){+.+.}-{3:3}, at: of_dma_request_slave_channel+0x138/0x280
#5: ffffb99d06a2ee20 (dma_list_mutex){+.+.}-{3:3}, at: dma_get_slave_channel+0x28/0x10c
stack backtrace:
CPU: 7 PID: 9 Comm: kworker/u16:0 Not tainted 6.3.0-rc5-00253-g99792582ded1-dirty #15
Hardware name: Google Pixel 3 (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0xa0/0xfc
show_stack+0x18/0x24
dump_stack_lvl+0x60/0xac
dump_stack+0x18/0x24
print_unlock_imbalance_bug+0x130/0x148
lock_release+0x270/0x300
__mutex_unlock_slowpath+0x48/0x2cc
mutex_unlock+0x20/0x2c
gpi_alloc_chan_resources+0x108/0x5bc
dma_chan_get+0x84/0x188
dma_get_slave_channel+0x5c/0x10c
gpi_of_dma_xlate+0x110/0x1a0
of_dma_request_slave_channel+0x174/0x280
dma_request_chan+0x3c/0x2d4
geni_i2c_probe+0x544/0x63c
platform_probe+0x68/0xc4
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0xe0
driver_probe_device+0x3c/0x160
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x84/0xe0
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
device_add+0x60c/0x7d8
of_device_add+0x44/0x60
of_platform_device_create_pdata+0x90/0x124
of_platform_bus_create+0x15c/0x3c8
of_platform_populate+0x58/0xf8
devm_of_platform_populate+0x58/0xbc
geni_se_probe+0xf0/0x164
platform_probe+0x68/0xc4
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0xe0
driver_probe_device+0x3c/0x160
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x84/0xe0
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x2bc/0x594
worker_thread+0x228/0x438
kthread+0x108/0x10c
ret_from_fork+0x10/0x20
Fixes: 5d0c3533a19f ("dmaengine: qcom: Add GPI dma driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230409233355.453741-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 57c0e1362fdd57d0cea7ab1e583b58abf4bd8c2d ]
In the wiz_mode_select() function, the configuration performed for
PHY_TYPE_USXGMII is unreachable. Fix it.
Fixes: b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in wiz driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230403094552.929108-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ulpi_port
[ Upstream commit e024854048e733391b31fe5a398704b31b9af803 ]
The tegra_xusb_port_unregister should be called when usb2_port
and ulpi_port map fails in tegra_xusb_add_usb2_port() or in
tegra_xusb_add_ulpi_port(), fix it.
Fixes: 53d2a715c240 ("phy: Add Tegra XUSB pad controller support")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221129111634.1547747-1-cuigaosheng1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a0d1740bd8fd7dafb81fcb102fb5d0b83b1ce73 ]
The existing code copies the hw_params pointer and reuses it later in
.prepare, specifically to re-initialize the ALH DMA channel
information that's lost in suspend-resume cycles.
This is not needed, we can directly access the information from the
substream/rtd - as done for the HDAudio DAIs in
sound/soc/sof/intel/hda-dai.c
In addition, using the saved pointer causes the suspend-resume test
cases to fail on specific platforms, depending on which version of GCC
is used. Péter Ujfalusi and I have spent long hours to root-cause this
problem that was reported by the Intel CI first with 6.2-rc1 and again
v6.3-rc1. In the latter case we were lucky that the problem was 100%
reproducible on local test devices, and found out that adding a
dev_dbg() or adding a call to usleep_range() just before accessing the
saved pointer "fixed" the issue. With errors appearing just by
changing the compiler version or minor changes in the code generated,
clearly we have a memory management Heisenbug.
The root-cause seems to be that the hw_params pointer is not
persistent. The soc-pcm code allocates the hw_params structure on the
stack, and passes it to the BE dailink hw_params and DAIs
hw_params. Saving such a pointer and reusing it later during the
.prepare stage cannot possibly work reliably, it's broken-by-design
since v5.10. It's astonishing that the problem was not seen earlier.
This simple fix will have to be back-ported to -stable, due to changes
to avoid the use of the get/set_dmadata routines this patch will only
apply on kernels older than v6.1.
Fixes: a5a0239c27fe ("soundwire: intel: reinitialize IP+DSP in .prepare(), but only when resuming")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230321022642.1426611-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e0767e391079687081c5564b1390983c36b49cd1 ]
The existing 'struct sdw_cdns_dma_data' has really nothing to do with
DMAs. The information is stored in the dai->dma_data, but this is
really private data that should be stored in a different context.
Beyond the academic elegance discussion, using dma_data is a problem
for new Intel hardware where the dma_data structure is already used
for true DMA handling performed by other parts of the code.
This patch prepares a transition away from the use of dma_data, for
now with a rename-only change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221101023521.2384586-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 0a0d1740bd8f ("soundwire: intel: don't save hw_params for use in prepare")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b16c310115f2084b8826a35b77ef42bab6786d9f ]
The DISP_PWM controller's default behavior is to always use register
double buffering: all reads/writes are then performed on shadow
registers instead of working registers and this becomes an issue
in case our chosen configuration in Linux is different from the
default (or from the one that was pre-applied by the bootloader).
An example of broken behavior is when the controller is configured
to use shadow registers, but this driver wants to configure it
otherwise: what happens is that the .get_state() callback is called
right after registering the pwmchip and checks whether the PWM is
enabled by reading the DISP_PWM_EN register;
At this point, if shadow registers are enabled but their content
was not committed before booting Linux, we are *not* reading the
current PWM enablement status, leading to the kernel knowing that
the hardware is actually enabled when, in reality, it's not.
The aforementioned issue emerged since this driver was fixed with
commit 0b5ef3429d8f ("pwm: mtk-disp: Fix the parameters calculated
by the enabled flag of disp_pwm") making it to read the enablement
status from the right register.
Configure the controller in the .get_state() callback to avoid
this desync issue and get the backlight properly working again.
Fixes: 3f2b16734914 ("pwm: mtk-disp: Implement atomic API .get_state()")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36dd7f530ae7d9ce9e853ffb8aa337de65c6600b ]
If shadow registers usage is not desired, disable that before performing
any write to CON0/1 registers in the .apply() callback, otherwise we may
lose clkdiv or period/width updates.
Fixes: cd4b45ac449a ("pwm: Add MediaTek MT2701 display PWM driver support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1087c29e96a48e9080377e168d35dcb52fb068b ]
Commit 96f524105b9c ("leds: tca6507: use fwnode API instead of OF")
changed to fwnode API but did not take into account that a missing property
"linux,default-trigger" now seems to return an error and as a side effect
sets value to -1. This seems to be different from of_get_property() which
always returned NULL in any case of error.
Neglecting this side-effect leads to
[ 11.201965] Unable to handle kernel paging request at virtual address ffffffff when read
in the strcmp() of led_trigger_set_default() if there is no led-trigger
defined in the DTS.
I don't know if this was recently introduced somewhere in the fwnode lib
or if the effect was missed in initial testing. Anyways it seems to be a
bug to ignore the error return value of an optional value here in the
driver.
Fixes: 96f524105b9c ("leds: tca6507: use fwnode API instead of OF")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/cbae7617db83113de726fcc423a805ebaa1bfca6.1680433978.git.hns@goldelico.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 827026ae2e56ec05ef1155661079badbbfc0b038 ]
If the probe is deferred, -EPROBE_DEFER should be returned, not
+EPROBE_DEFER.
Fixes: 3cd2c313f1d6 ("dmaengine: mv_xor_v2: Fix clock resource by adding a register clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/201170dff832a3c496d125772e10070cd834ebf2.1679814350.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c19147d9cfc0f9328049d2e278279150d7de9ca ]
There have been stable releases with the ralink,rt2880-pinmux compatible
string included. Having it removed breaks the ABI. Reintroduce it.
Fixes: e5981cd46183 ("pinctrl: ralink: add new compatible strings for each pinctrl subdriver")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230317213011.13656-2-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a61079efc87888587e463afaed82417b162fbd69 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3fce8e1eb994 ("leds: TI LMU: Add common code for TI LMU devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230226053953.4681-5-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9da805344d2a2d27a32cc9271230055d8818e887 ]
According to R-Car V4H Series User’s Manual: Hardware Rev. 0.54, the
ERROROUTC signal is active-low. Hence add the missing "_N" suffix to
the pin function's names.
Resize column 2 of all IPxSR* definitions to accomodate the longer
names.
Fixes: b811062e5fd0343c ("pinctrl: renesas: r8a779g0: Add missing ERROROUTC_A")
Fixes: ad9bb2fec66262b0 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1774303989e7d61f08fa81f1c2fa1b394505645f.1669036423.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 203734a0419cade9c76016f66e2c7ba354c249b4 ]
According to R-Car V4H Series User’s Manual: Hardware Rev. 0.54, pin
groups 6 and 7 do not use Module Select Registers to configure pin
functions.
Hence:
- Remove the non-existent Module Select Registers (MODSEL[67]),
- Correct the affected PINMUX definitions.
Fixes: 36611d28f5130d8b ("pinctrl: renesas: r8a779g0: Add missing MODSELx for AVBx")
Fixes: ad9bb2fec66262b0 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/06972cafd0efa4cfb395cfa76000a1bdae5e9e73.1669036423.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a7a5226e7b177c68800985a19a80c1df9bceff6 ]
According to R-Car V4H Series User’s Manual: Hardware Rev. 0.54, pin
groups 4 and 5 do not use Module Select Registers to configure pin
functions, but use Peripheral Function Select Registers instead.
Hence:
- Remove the non-existent Module Select Registers (MODSEL[45]),
- Add the missing Peripheral Function Select Registers (IPxSR[45]),
- Correct the GPIO / Peripheral Function Select Register definitions
(GPSR]45_*),
- Correct the affected PINMUX definitions.
Fixes: 36611d28f5130d8b ("pinctrl: renesas: r8a779g0: Add missing MODSELx for AVBx")
Fixes: 36fb7b8af55b83e0 ("pinctrl: renesas: r8a779g0: Add missing MODSELx for TSN0")
Fixes: ad9bb2fec66262b0 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3d3833d1738f5e8fcc4c1002aa93832464d129a0.1669036423.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 60003351e99167d8cfa7c161e95856efc016f381 ]
Correct a typo mistake in the definition of the tsn1_avtp_pps pin group
mux.
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Fixes: babe298e9caaa3d7 ("pinctrl: renesas: r8a779f0: Add Ethernet pins, groups, and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/45ea6e87b91c36fd0b9706cf58ff50a4d1a99c44.1674825039.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a145c9a8674ac8fbfa1595276e1b6cbfc5139038 ]
AVB[01]_{MAGIC,MDC,MDIO,TXCREFCLK} are registered as both
PINMUX_SINGLE(fn) and PINMUX_IPSR_GPSR(fn) in the pinmux_data array.
The latter are correct, hence remove the former.
Without this fix, the Ethernet PHY is not operational on the MDIO bus.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Fixes: 741a7370fc3b8b54 ("pinctrl: renesas: Initial R8A779A0 (V3U) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6fd217b71e83ba9a8157513ed671a1fa218b23b6.1674824958.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 835659598c67907b98cd2aa57bb951dfaf675c69 ]
Syzbot found the following issue:
loop0: detected capacity change from 0 to 2048
EXT4-fs (loop0): mounted filesystem 00000000-0000-0000-0000-000000000000 without journal. Quota mode: none.
==================================================================
BUG: KASAN: use-after-free in ext4_ext_binsearch_idx fs/ext4/extents.c:768 [inline]
BUG: KASAN: use-after-free in ext4_find_extent+0x76e/0xd90 fs/ext4/extents.c:931
Read of size 4 at addr ffff888073644750 by task syz-executor420/5067
CPU: 0 PID: 5067 Comm: syz-executor420 Not tainted 6.2.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x290 lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:306
print_report+0x107/0x1f0 mm/kasan/report.c:417
kasan_report+0xcd/0x100 mm/kasan/report.c:517
ext4_ext_binsearch_idx fs/ext4/extents.c:768 [inline]
ext4_find_extent+0x76e/0xd90 fs/ext4/extents.c:931
ext4_clu_mapped+0x117/0x970 fs/ext4/extents.c:5809
ext4_insert_delayed_block fs/ext4/inode.c:1696 [inline]
ext4_da_map_blocks fs/ext4/inode.c:1806 [inline]
ext4_da_get_block_prep+0x9e8/0x13c0 fs/ext4/inode.c:1870
ext4_block_write_begin+0x6a8/0x2290 fs/ext4/inode.c:1098
ext4_da_write_begin+0x539/0x760 fs/ext4/inode.c:3082
generic_perform_write+0x2e4/0x5e0 mm/filemap.c:3772
ext4_buffered_write_iter+0x122/0x3a0 fs/ext4/file.c:285
ext4_file_write_iter+0x1d0/0x18f0
call_write_iter include/linux/fs.h:2186 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x7dc/0xc50 fs/read_write.c:584
ksys_write+0x177/0x2a0 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f4b7a9737b9
RSP: 002b:00007ffc5cac3668 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f4b7a9737b9
RDX: 00000000175d9003 RSI: 0000000020000200 RDI: 0000000000000004
RBP: 00007f4b7a933050 R08: 0000000000000000 R09: 0000000000000000
R10: 000000000000079f R11: 0000000000000246 R12: 00007f4b7a9330e0
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Above issue is happens when enable bigalloc and inline data feature. As
commit 131294c35ed6 fixed delayed allocation bug in ext4_clu_mapped for
bigalloc + inline. But it only resolved issue when has inline data, if
inline data has been converted to extent(ext4_da_convert_inline_data_to_extent)
before writepages, there is no EXT4_STATE_MAY_INLINE_DATA flag. However
i_data is still store inline data in this scene. Then will trigger UAF
when find extent.
To resolve above issue, there is need to add judge "ext4_has_inline_data(inode)"
in ext4_clu_mapped().
Fixes: 131294c35ed6 ("ext4: fix delayed allocation bug in ext4_clu_mapped for bigalloc + inline")
Reported-by: syzbot+bf4bb7731ef73b83a3b4@syzkaller.appspotmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230406111627.1916759-1-tudor.ambarus@linaro.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1dedde690303c05ef732b7c5c8356fdf60a4ade3 ]
It is possible for i_disksize can exceed i_size, triggering a warning.
generic_perform_write
copied = iov_iter_copy_from_user_atomic(len) // copied < len
ext4_da_write_end
| ext4_update_i_disksize
| new_i_size = pos + copied;
| WRITE_ONCE(EXT4_I(inode)->i_disksize, newsize) // update i_disksize
| generic_write_end
| copied = block_write_end(copied, len) // copied = 0
| if (unlikely(copied < len))
| if (!PageUptodate(page))
| copied = 0;
| if (pos + copied > inode->i_size) // return false
if (unlikely(copied == 0))
goto again;
if (unlikely(iov_iter_fault_in_readable(i, bytes))) {
status = -EFAULT;
break;
}
We get i_disksize greater than i_size here, which could trigger WARNING
check 'i_size_read(inode) < EXT4_I(inode)->i_disksize' while doing dio:
ext4_dio_write_iter
iomap_dio_rw
__iomap_dio_rw // return err, length is not aligned to 512
ext4_handle_inode_extension
WARN_ON_ONCE(i_size_read(inode) < EXT4_I(inode)->i_disksize) // Oops
WARNING: CPU: 2 PID: 2609 at fs/ext4/file.c:319
CPU: 2 PID: 2609 Comm: aa Not tainted 6.3.0-rc2
RIP: 0010:ext4_file_write_iter+0xbc7
Call Trace:
vfs_write+0x3b1
ksys_write+0x77
do_syscall_64+0x39
Fix it by updating 'copied' value before updating i_disksize just like
ext4_write_inline_data_end() does.
A reproducer can be found in the buganizer link below.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217209
Fixes: 64769240bd07 ("ext4: Add delayed allocation support in data=writeback mode")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230321013721.89818-1-chengzhihao1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d906be3fa571f6fc9381911304a0eca99f1b6951 ]
We should not cache deferred file handles if we dont have
handle lease on a file. And we should immediately close all
deferred handles in case of handle lease break.
Fixes: 9e31678fb403 ("SMB3: fix lease break timeout when multiple deferred close handles for the same file.")
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab9ddc87a9055c4bebd6524d5d761d605d52e557 ]
cifs_del_deferred_close function has a critical section which modifies
the deferred close file list. We must acquire deferred_lock before
calling cifs_del_deferred_close function.
Fixes: ca08d0eac020 ("cifs: Fix memory leak on the deferred close")
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Acked-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 158009f1b4a33bc0f354b994eea361362bd83226 ]
There was never a function named ktime_get_fast_ns().
Presumably these should refer to ktime_get_mono_fast_ns() instead.
Fixes: c1ce406e80fb15fa ("timekeeping: Fix up function documentation for the NMI safe accessors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/06df7b3cbd94f016403bbf6cd2b38e4368e7468f.1682516546.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 812489ac4dd91144a74ce65ecf232252a2e406fb ]
In commit 91993c8c2ed5 ("openrisc: use shadow registers to save regs on
exception") the unhandled exception path was changed to do an early
store of r30 instead of r31. The entry code was not updated and r31 is
not getting stored to pt_regs.
This patch updates the entry handler to store r31 instead of r30. We
also remove some misleading commented out store r30 and r31
instructrions.
I noticed this while working on adding floating point exception
handling, This issue probably would never impact anything since we kill
the process or Oops right away on unhandled exceptions.
Fixes: 91993c8c2ed5 ("openrisc: use shadow registers to save regs on exception")
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
init fails
[ Upstream commit fb73556386e074e9bee9fa2d253aeaefe4e063e0 ]
Smatch reports:
drivers/clocksource/timer-davinci.c:332 davinci_timer_register()
warn: 'base' from ioremap() not released on lines: 274.
Fix this and other potential memory leak problems
by adding a set of corresponding exit lables.
Fixes: 721154f972aa ("clocksource/drivers/davinci: Add support for clockevents")
Signed-off-by: Qinrun Dai <flno@hust.edu.cn>
Link: https://lore.kernel.org/r/20230413135037.1505799-1-flno@hust.edu.cn
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 746aa3c8cb1a650ff2583497ac646e505831b9b9 ]
Just like other QP types, when modify DC, the port_num should be compared
with dev->num_ports, instead of HCA_CAP.num_ports. Otherwise Multi-port
vHCA on DC may not work.
Fixes: 776a3906b692 ("IB/mlx5: Add support for DC target QP")
Link: https://lore.kernel.org/r/20230420013906.1244185-1-markzhang@nvidia.com
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 691d0b782066a6eeeecbfceb7910a8f6184e6105 ]
Currently call_bind_status places a hard limit of 3 to the number of
retries on EACCES error. This limit was done to prevent NLM unlock
requests from being hang forever when the server keeps returning garbage.
However this change causes problem for cases when NLM service takes
longer than 9 seconds to register with the port mapper after a restart.
This patch removes this hard coded limit and let the RPC handles
the retry based on the standard hard/soft task semantics.
Fixes: 0b760113a3a1 ("NLM: Don't hang forever on NLM unlock requests")
Reported-by: Helen Chao <helen.chao@oracle.com>
Tested-by: Helen Chao <helen.chao@oracle.com>
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e358ea8614ddfbc59ca7a3f5dff5dde2b350b2c ]
Commit cited in "fixes" tag added bulk support for flow counters but it
didn't account that's also possible to query a counter using a non-base id
if the counter was allocated as bulk.
When a user performs a query, validate the flow counter id given in the
mailbox is inside the valid range taking bulk value into account.
Fixes: 208d70f562e5 ("IB/mlx5: Support flow counters offset for bulk counters")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Link: https://lore.kernel.org/r/79d7fbe291690128e44672418934256254d93115.1681377114.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d43b020b0f82c088ef8ff3196ef00575a97d200e ]
relaxed_ordering_read HCA capability is set if both the device supports
relaxed ordering (RO) read and RO is set in PCI config space.
RO in PCI config space can change during runtime. This will change the
value of relaxed_ordering_read HCA capability in FW, but the driver will
not see it since it queries the capabilities only once.
This can lead to the following scenario:
1. RO in PCI config space is enabled.
2. User creates MKey without RO.
3. RO in PCI config space is disabled.
As a result, relaxed_ordering_read HCA capability is turned off in FW
but remains on in driver copy of the capabilities.
4. User requests to reconfig the MKey with RO via UMR.
5. Driver will try to reconfig the MKey with RO read although it
shouldn't (as relaxed_ordering_read HCA capability is really off).
To fix this, check pcie_relaxed_ordering_enabled() before setting RO
read in UMR.
Fixes: 896ec9735336 ("RDMA/mlx5: Set mkey relaxed ordering by UMR with ConnectX-7")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Link: https://lore.kernel.org/r/8d39eb8317e7bed1a354311a20ae707788fd94ed.1681131553.git.leon@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5499d01c029069044a3b3e50501c77b474c96178 ]
For io_tlb_nslabs, the debugfs code reports the correct value for a
specific reserved memory pool. But for io_tlb_used, the value reported
is always for the default pool, not the specific reserved pool. Fix this.
Fixes: 5c850d31880e ("swiotlb: fix passing local variable to debugfs_create_ulong()")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a90922fa25370902322e9de6640e58737d459a50 ]
The reservedmem_of_init_fn's are invoked very early at boot before the
memory zones have even been defined. This makes it inappropriate to test
whether the page corresponding to a PFN is in ZONE_HIGHMEM from within
one.
Removing the check allows an ARM 32-bit kernel with SPARSEMEM enabled to
boot properly since otherwise we would be de-referencing an
uninitialized sparsemem map to perform pfn_to_page() check.
The arm64 architecture happens to work (and also has no high memory) but
other 32-bit architectures could also be having similar issues.
While it would be nice to provide early feedback about a reserved DMA
pool residing in highmem, it is not possible to do that until the first
time we try to use it, which is where the check is moved to.
Fixes: 0b84e4f8b793 ("swiotlb: Add restricted DMA pool initialization")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5bca3688bdbc3b58a2894b8671a8e2378efe28bd ]
rpi_firmware_get() take reference, we need to release it in error paths
as well. Use devm_rpi_firmware_get() helper to handling the resources.
Also remove the existing rpi_firmware_put().
Fixes: 0b9f28fed3f7 ("Input: add official Raspberry Pi's touchscreen driver")
Fixes: 3b8ddff780b7 ("input: raspberrypi-ts: Release firmware handle when not needed")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221223074657.810346-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68d1151f03067533827fc50b770954ef33149533 ]
There's only one DSI PHY on this SoC. Remove the ghost entry for the
clock produced by a secondary one.
Fixes: cc517ea3333f ("clk: qcom: Add display clock controller driver for QCM2290")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230412-topic-qcm_dispcc-v1-2-bf2989a75ae4@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62db82f9c8004f1226f5cec8a5441fb89eb984fa ]
The test clock apparently it's not used by anyone upstream. Remove it.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221228185237.3111988-9-dmitry.baryshkov@linaro.org
Stable-dep-of: 68d1151f0306 ("clk: qcom: dispcc-qcm2290: Remove inexistent DSI1PHY clk")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a500e0bc97b6cb3c0d9859e81973b8dd07d1b7b ]
On SM8350 platform the PCIe PIPE clocks require additional handling to
function correctly. They are to be switched to the tcxo source before
turning PCIe GDSCs off and should be switched to PHY PIPE source once
they are working. Switch PCIe PHY clocks to use clk_regmap_phy_mux_ops,
which provide support for this dance.
Fixes: 44c20c9ed37f ("clk: qcom: gcc: Add clock driver for SM8350")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230412134829.3686467-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
lpass_cc_sc7280_desc
[ Upstream commit aad09fc7c4a522892eb64a79627b17a3869936cb ]
Add GDSCs in lpass_cc_sc7280_desc struct.
When qcom,adsp-pil-mode is enabled, GDSCs required to solve
dependencies in lpass_audiocc probe().
Fixes: 0cbcfbe50cbf ("clk: qcom: lpass: Handle the regmap overlap of lpasscc and lpass_aon")
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407092255.119690-4-quic_mohs@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4fc1c2d9a2b7a394f3b873aae5e03bffd8b5cd31 ]
The qdsp6ss memory region is being shared by ADSP remoteproc device and
lpasscc clock device, hence causing memory conflict.
To avoid this, when qdsp6ss clocks are being enabled in remoteproc driver,
skip qdsp6ss clock registration if "qcom,adsp-pil-mode" is enabled and
also assign max_register value.
Fixes: 4ab43d171181 ("clk: qcom: Add lpass clock controller driver for SC7280")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407092255.119690-3-quic_mohs@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f880d19e6ad645a4b8066d5ff091c980b3231e7 ]
With the addition of the V2 page table support, the domain page size
bitmap needs to be set prior to iommu core setting up direct mappings
for reserved regions. When reserved regions are mapped, if this is not
done, it will be looking at the V1 page size bitmap when determining
the page size to use in iommu_pgsize(). When it gets into the actual
amd mapping code, a check of see if the page size is supported can
fail, because at that point it is checking it against the V2 page size
bitmap which only supports 4K, 2M, and 1G.
Add a check to __iommu_domain_alloc() to not override the
bitmap if it was already set by the iommu ops domain_alloc() code path.
Cc: Vasant Hegde <vasant.hegde@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Fixes: 4db6c41f0946 ("iommu/amd: Add support for using AMD IOMMU v2 page table for DMA-API")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20230404072742.1895252-1-jsnitsel@redhat.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 40882deb83c29d8df4470d4e5e7f137b6acf7ad1 ]
The spec requires that we always at least send a RECLAIM_COMPLETE when
we're done establishing the lease and recovering any state.
Fixes: fce5c838e133 ("nfs41: RECLAIM_COMPLETE functionality")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d608c18018c897b88d66f1340fe274b7181817fa ]
XBAR_DIVBUS and AD_SLOW should set parent to XBAR_AD_DIVPLAT and
XBAR_DIVBUS respectively, not the NIC_AD. otherwise we will get
wrong clock rate.
Fixes: c43a801a5789 ("clk: imx: Add clock driver for imx8ulp")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230331063814.2462059-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4435467b15b069e5a6f50ca9a9260e86b74dbc13 ]
When programming PLL, should disable Hardware control select to make PLL
controlled by register, not hardware inputs through OSCPLL.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230403095300.3386988-3-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf8dccfedce848f67eaa42e8839305d028319161 ]
The Fvco should be range 2.4GHz to 5GHz, the original table voilate the
spec, so update the table to fix it.
Fixes: c196175acdd3 ("clk: imx: clk-fracn-gppll: Add more freq config for video pll")
Fixes: 044034efbeea ("clk: imx: clk-fracn-gppll: fix mfd value")
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230403095300.3386988-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00cbce5cbf88459cd1aa1d60d0f1df15477df127 ]
hfi1 user SDMA request processing has two bugs that can cause data
corruption for user SDMA requests that have multiple payload iovecs
where an iovec other than the tail iovec does not run up to the page
boundary for the buffer pointed to by that iovec.a
Here are the specific bugs:
1. user_sdma_txadd() does not use struct user_sdma_iovec->iov.iov_len.
Rather, user_sdma_txadd() will add up to PAGE_SIZE bytes from iovec
to the packet, even if some of those bytes are past
iovec->iov.iov_len and are thus not intended to be in the packet.
2. user_sdma_txadd() and user_sdma_send_pkts() fail to advance to the
next iovec in user_sdma_request->iovs when the current iovec
is not PAGE_SIZE and does not contain enough data to complete the
packet. The transmitted packet will contain the wrong data from the
iovec pages.
This has not been an issue with SDMA packets from hfi1 Verbs or PSM2
because they only produce iovecs that end short of PAGE_SIZE as the tail
iovec of an SDMA request.
Fixing these bugs exposes other bugs with the SDMA pin cache
(struct mmu_rb_handler) that get in way of supporting user SDMA requests
with multiple payload iovecs whose buffers do not end at PAGE_SIZE. So
this commit fixes those issues as well.
Here are the mmu_rb_handler bugs that non-PAGE_SIZE-end multi-iovec
payload user SDMA requests can hit:
1. Overlapping memory ranges in mmu_rb_handler will result in duplicate
pinnings.
2. When extending an existing mmu_rb_handler entry (struct mmu_rb_node),
the mmu_rb code (1) removes the existing entry under a lock, (2)
releases that lock, pins the new pages, (3) then reacquires the lock
to insert the extended mmu_rb_node.
If someone else comes in and inserts an overlapping entry between (2)
and (3), insert in (3) will fail.
The failure path code in this case unpins _all_ pages in either the
original mmu_rb_node or the new mmu_rb_node that was inserted between
(2) and (3).
3. In hfi1_mmu_rb_remove_unless_exact(), mmu_rb_node->refcount is
incremented outside of mmu_rb_handler->lock. As a result, mmu_rb_node
could be evicted by another thread that gets mmu_rb_handler->lock and
checks mmu_rb_node->refcount before mmu_rb_node->refcount is
incremented.
4. Related to #2 above, SDMA request submission failure path does not
check mmu_rb_node->refcount before freeing mmu_rb_node object.
If there are other SDMA requests in progress whose iovecs have
pointers to the now-freed mmu_rb_node(s), those pointers to the
now-freed mmu_rb nodes will be dereferenced when those SDMA requests
complete.
Fixes: 7be85676f1d1 ("IB/hfi1: Don't remove RB entry when not needed.")
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/168088636445.3027109.10054635277810177889.stgit@252.162.96.66.static.eigbox.net
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fe8fec5e43d5a80f43cbf61aaada1b047a1eb61 ]
hfi1_mmu_rb_remove_unless_exact() did not move mmu_rb_node objects in
mmu_rb_handler->lru_list after getting a cache hit on an mmu_rb_node.
As a result, hfi1_mmu_rb_evict() was not guaranteed to evict truly
least-recently used nodes.
This could be a performance issue for an application when that
application:
- Uses some long-lived buffers frequently.
- Uses a large number of buffers once.
- Hits the mmu_rb_handler cache size or pinned-page limits, forcing
mmu_rb_handler cache entries to be evicted.
In this case, the one-time use buffers cause the long-lived buffer
entries to eventually filter to the end of the LRU list where
hfi1_mmu_rb_evict() will consider evicting a frequently-used long-lived
entry instead of evicting one of the one-time use entries.
Fix this by inserting new mmu_rb_node at the tail of
mmu_rb_handler->lru_list and move mmu_rb_ndoe to the tail of
mmu_rb_handler->lru_list when the mmu_rb_node is a hit in
hfi1_mmu_rb_remove_unless_exact(). Change hfi1_mmu_rb_evict() to evict
from the head of mmu_rb_handler->lru_list instead of the tail.
Fixes: 0636e9ab8355 ("IB/hfi1: Add cache evict LRU list")
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/168088635931.3027109.10423156330761536044.stgit@252.162.96.66.static.eigbox.net
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eca5cd9474cd26d62f9756f536e2e656d3f62f3a ]
When unregistering MAD agent, srpt module has a non-null check
for 'mad_agent' pointer before invoking ib_unregister_mad_agent().
This check can pass if 'mad_agent' variable holds an error value.
The 'mad_agent' can have an error value for a short window when
srpt_add_one() and srpt_remove_one() is executed simultaneously.
In srpt module, added a valid pointer check for 'sport->mad_agent'
before unregistering MAD agent.
This issue can hit when RoCE driver unregisters ib_device
Stack Trace:
------------
BUG: kernel NULL pointer dereference, address: 000000000000004d
PGD 145003067 P4D 145003067 PUD 2324fe067 PMD 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 10 PID: 4459 Comm: kworker/u80:0 Kdump: loaded Tainted: P
Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.5.4 01/13/2020
Workqueue: bnxt_re bnxt_re_task [bnxt_re]
RIP: 0010:_raw_spin_lock_irqsave+0x19/0x40
Call Trace:
ib_unregister_mad_agent+0x46/0x2f0 [ib_core]
IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
? __schedule+0x20b/0x560
srpt_unregister_mad_agent+0x93/0xd0 [ib_srpt]
srpt_remove_one+0x20/0x150 [ib_srpt]
remove_client_context+0x88/0xd0 [ib_core]
bond0: (slave p2p1): link status definitely up, 100000 Mbps full duplex
disable_device+0x8a/0x160 [ib_core]
bond0: active interface up!
? kernfs_name_hash+0x12/0x80
(NULL device *): Bonding Info Received: rdev: 000000006c0b8247
__ib_unregister_device+0x42/0xb0 [ib_core]
(NULL device *): Master: mode: 4 num_slaves:2
ib_unregister_device+0x22/0x30 [ib_core]
(NULL device *): Slave: id: 105069936 name:p2p1 link:0 state:0
bnxt_re_stopqps_and_ib_uninit+0x83/0x90 [bnxt_re]
bnxt_re_alloc_lag+0x12e/0x4e0 [bnxt_re]
Fixes: a42d985bd5b2 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Link: https://lore.kernel.org/r/20230406042549.507328-1-saravanan.vajravel@broadcom.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd9de1badac7e4ff6780365d4aa38983f5e2a436 ]
Trace icm_send_rej event before the cm state is reset to idle, so that
correct cm state will be logged. For example when an incoming request is
rejected, the old trace log was:
icm_send_rej: local_id=961102742 remote_id=3829151631 state=IDLE reason=REJ_CONSUMER_DEFINED
With this patch:
icm_send_rej: local_id=312971016 remote_id=3778819983 state=MRA_REQ_SENT reason=REJ_CONSUMER_DEFINED
Fixes: 8dc105befe16 ("RDMA/cm: Add tracepoints to track MAD send operations")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/20230330072351.481200-1-markzhang@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
