global: Remove unused or unnecessary CONFIG symbols related to DDR

These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>

11 files changed, 2 insertions, 134 deletions

diff --git a/arch/powerpc/cpu/mpc83xx/spd_sdram.c b/arch/powerpc/cpu/mpc83xx/spd_sdram.c
index a861e8dd2dd..e12043b2609 100644
--- a/arch/powerpc/cpu/mpc83xx/spd_sdram.c
+++ b/arch/powerpc/cpu/mpc83xx/spd_sdram.c
@@ -834,12 +834,6 @@ long int spd_sdram()
 #endif
 	debug("   DDRC ECC mode: %s\n", ddrc_ecc_enable ? "ON":"OFF");
 
-#if defined(CONFIG_DDR_2T_TIMING)
-	/*
-	 * Enable 2T timing by setting sdram_cfg[16].
-	 */
-	sdram_cfg |= SDRAM_CFG_2T_EN;
-#endif
 	/* Enable controller, and GO! */
 	ddr->sdram_cfg = sdram_cfg;
 	sync();
@@ -914,16 +908,12 @@ void ddr_enable_ecc(unsigned int dram_size)
 	pattern[0] = 0xdeadbeef;
 	pattern[1] = 0xdeadbeef;
 
-#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
-	dma_meminit(pattern[0], dram_size);
-#else
 	debug("ddr init: CPU FP write method\n");
 	size = dram_size;
 	for (p = 0; p < (u64*)(size); p++) {
 		ppcDWstore((u32*)p, pattern);
 	}
 	sync();
-#endif
 
 	t_end = get_tbms();
 	icache_disable();
diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h
index 2c96378efef..2a78551ce39 100644
--- a/arch/powerpc/include/asm/config.h
+++ b/arch/powerpc/include/asm/config.h
@@ -28,8 +28,7 @@
 
 /* Check if boards need to enable FSL DMA engine for SDRAM init */
 #if !defined(CONFIG_FSL_DMA) && defined(CONFIG_DDR_ECC)
-#if (defined(CONFIG_MPC83xx) && defined(CONFIG_DDR_ECC_INIT_VIA_DMA)) || \
-	((defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)) && \
+#if ((defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)) && \
 	!defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER))
 #define CONFIG_FSL_DMA
 #endif
diff --git a/board/freescale/mpc8349emds/mpc8349emds.c b/board/freescale/mpc8349emds/mpc8349emds.c
index c4c7f528b58..eff248104dc 100644
--- a/board/freescale/mpc8349emds/mpc8349emds.c
+++ b/board/freescale/mpc8349emds/mpc8349emds.c
@@ -100,21 +100,6 @@ int fixed_sdram(void)
 #if (CONFIG_SYS_DDR_SIZE != 256)
 #warning Currenly any ddr size other than 256 is not supported
 #endif
-#ifdef CONFIG_DDR_II
-	im->ddr.csbnds[2].csbnds = CONFIG_SYS_DDR_CS2_BNDS;
-	im->ddr.cs_config[2] = CONFIG_SYS_DDR_CS2_CONFIG;
-	im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
-	im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
-	im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
-	im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
-	im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
-	im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
-	im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
-	im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
-	im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
-	im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL;
-#else
-
 #if ((CONFIG_SYS_SDRAM_BASE & 0x00FFFFFF) != 0)
 #warning Chip select bounds is only configurable in 16MB increments
 #endif
@@ -134,18 +119,10 @@ int fixed_sdram(void)
 
 	im->ddr.sdram_cfg =
 		SDRAM_CFG_SREN
-#if defined(CONFIG_DDR_2T_TIMING)
-		| SDRAM_CFG_2T_EN
-#endif
 		| 2 << SDRAM_CFG_SDRAM_TYPE_SHIFT;
-#if defined (CONFIG_DDR_32BIT)
-	/* for 32-bit mode burst length is 8 */
-	im->ddr.sdram_cfg |= (SDRAM_CFG_32_BE | SDRAM_CFG_8_BE);
-#endif
 	im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
 
 	im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
-#endif
 	udelay(200);
 
 	/* enable DDR controller */
diff --git a/drivers/dma/fsl_dma.c b/drivers/dma/fsl_dma.c
index b7eddf0f04c..1864b5d88b0 100644
--- a/drivers/dma/fsl_dma.c
+++ b/drivers/dma/fsl_dma.c
@@ -130,11 +130,9 @@ int dmacpy(phys_addr_t dest, phys_addr_t src, phys_size_t count) {
 
 /*
  * 85xx/86xx use dma to initialize SDRAM when !CONFIG_ECC_INIT_VIA_DDRCONTROLLER
- * while 83xx uses dma to initialize SDRAM when CONFIG_DDR_ECC_INIT_VIA_DMA
  */
 #if ((!defined CONFIG_MPC83xx && defined(CONFIG_DDR_ECC) &&	\
-	!defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)) ||		\
-	(defined(CONFIG_MPC83xx) && defined(CONFIG_DDR_ECC_INIT_VIA_DMA)))
+	!defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)))
 void dma_meminit(uint val, uint size)
 {
 	uint *p = 0;
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index d5af4e8166a..9e487b8da29 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -38,23 +38,9 @@
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
-/*
- * 32-bit data path mode.
- *
- * Please note that using this mode for devices with the real density of 64-bit
- * effectively reduces the amount of available memory due to the effect of
- * wrapping around while translating address to row/columns, for example in the
- * 256MB module the upper 128MB get aliased with contents of the lower
- * 128MB); normally this define should be used for devices with real 32-bit
- * data path.
- */
-#undef CONFIG_DDR_32BIT
-
 #define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
 					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#undef  CONFIG_DDR_2T_TIMING
-
 /*
  * DDRCDR - DDR Control Driver Register
  */
@@ -70,21 +56,6 @@
  * Manually set up DDR parameters
  */
 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
-#if defined(CONFIG_DDR_II)
-#define CONFIG_SYS_DDRCDR		0x80080001
-#define CONFIG_SYS_DDR_CS2_BNDS		0x0000000f
-#define CONFIG_SYS_DDR_CS2_CONFIG	0x80330102
-#define CONFIG_SYS_DDR_TIMING_0		0x00220802
-#define CONFIG_SYS_DDR_TIMING_1		0x38357322
-#define CONFIG_SYS_DDR_TIMING_2		0x2f9048c8
-#define CONFIG_SYS_DDR_TIMING_3		0x00000000
-#define CONFIG_SYS_DDR_CLK_CNTL		0x02000000
-#define CONFIG_SYS_DDR_MODE		0x47d00432
-#define CONFIG_SYS_DDR_MODE2		0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL		0x03cf0080
-#define CONFIG_SYS_DDR_SDRAM_CFG	0x43000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#else
 #define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
 				| CSCONFIG_ROW_BIT_13 \
 				| CSCONFIG_COL_BIT_10)
@@ -93,17 +64,10 @@
 #define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
 #define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
 
-#if defined(CONFIG_DDR_32BIT)
-/* set burst length to 8 for 32-bit data path */
-				/* DLL,normal,seq,4/2.5, 8 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000023
-#else
 /* the default burst length is 4 - for 64-bit data path */
 				/* DLL,normal,seq,4/2.5, 4 burst len */
 #define CONFIG_SYS_DDR_MODE	0x00000022
 #endif
-#endif
-#endif
 
 /*
  * SDRAM on the Local Bus
diff --git a/include/configs/MPC8349EMDS_SDRAM.h b/include/configs/MPC8349EMDS_SDRAM.h
index ac12b22e64e..e652309da58 100644
--- a/include/configs/MPC8349EMDS_SDRAM.h
+++ b/include/configs/MPC8349EMDS_SDRAM.h
@@ -38,23 +38,9 @@
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
-/*
- * 32-bit data path mode.
- *
- * Please note that using this mode for devices with the real density of 64-bit
- * effectively reduces the amount of available memory due to the effect of
- * wrapping around while translating address to row/columns, for example in the
- * 256MB module the upper 128MB get aliased with contents of the lower
- * 128MB); normally this define should be used for devices with real 32-bit
- * data path.
- */
-#undef CONFIG_DDR_32BIT
-
 #define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
 					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#undef  CONFIG_DDR_2T_TIMING
-
 /*
  * DDRCDR - DDR Control Driver Register
  */
@@ -70,21 +56,6 @@
  * Manually set up DDR parameters
  */
 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
-#if defined(CONFIG_DDR_II)
-#define CONFIG_SYS_DDRCDR		0x80080001
-#define CONFIG_SYS_DDR_CS2_BNDS		0x0000000f
-#define CONFIG_SYS_DDR_CS2_CONFIG	0x80330102
-#define CONFIG_SYS_DDR_TIMING_0		0x00220802
-#define CONFIG_SYS_DDR_TIMING_1		0x38357322
-#define CONFIG_SYS_DDR_TIMING_2		0x2f9048c8
-#define CONFIG_SYS_DDR_TIMING_3		0x00000000
-#define CONFIG_SYS_DDR_CLK_CNTL		0x02000000
-#define CONFIG_SYS_DDR_MODE		0x47d00432
-#define CONFIG_SYS_DDR_MODE2		0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL		0x03cf0080
-#define CONFIG_SYS_DDR_SDRAM_CFG	0x43000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#else
 #define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
 				| CSCONFIG_ROW_BIT_13 \
 				| CSCONFIG_COL_BIT_10)
@@ -93,17 +64,10 @@
 #define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
 #define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
 
-#if defined(CONFIG_DDR_32BIT)
-/* set burst length to 8 for 32-bit data path */
-				/* DLL,normal,seq,4/2.5, 8 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000023
-#else
 /* the default burst length is 4 - for 64-bit data path */
 				/* DLL,normal,seq,4/2.5, 4 burst len */
 #define CONFIG_SYS_DDR_MODE	0x00000022
 #endif
-#endif
-#endif
 
 /*
  * SDRAM on the Local Bus
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index 1d2389a1c60..5d5efd09678 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -113,17 +113,9 @@
 				| (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 				/* 0x06090100 */
 
-#if defined(CONFIG_DDR_2T_TIMING)
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
-					| SDRAM_CFG_SDRAM_TYPE_DDR2 \
-					| SDRAM_CFG_32_BE \
-					| SDRAM_CFG_2T_EN)
-					/* 0x43088000 */
-#else
 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
 					| SDRAM_CFG_SDRAM_TYPE_DDR2)
 					/* 0x43000000 */
-#endif
 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00001000 /* 1 posted refresh */
 #define CONFIG_SYS_DDR_MODE		((0x0406 << SDRAM_MODE_ESD_SHIFT) \
 					| (0x0442 << SDRAM_MODE_SD_SHIFT))
diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index 86bfc746d87..a3caee4254b 100644
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -171,11 +171,6 @@
 #endif
 
 /* DDR Setup */
-#define CONFIG_DDR_ECC_ENABLE
-#ifndef CONFIG_DDR_ECC_ENABLE
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_DDR_SPD
-#endif
 #define CONFIG_SYS_SPD_BUS_NUM 1
 
 #define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_512M
@@ -204,11 +199,7 @@
 #define CONFIG_SYS_DDR_SR_CNTR		0x00000000
 #define CONFIG_SYS_DDR_RCW_1		0x00000000
 #define CONFIG_SYS_DDR_RCW_2		0x00000000
-#ifdef CONFIG_DDR_ECC_ENABLE
 #define CONFIG_SYS_DDR_CONTROL		0xE70C0000	/* Type = DDR3 & ECC */
-#else
-#define CONFIG_SYS_DDR_CONTROL		0xC70C0000	/* Type = DDR3 */
-#endif
 #define CONFIG_SYS_DDR_CONTROL_2	0x04401050
 #define CONFIG_SYS_DDR_TIMING_4		0x00220001
 #define CONFIG_SYS_DDR_TIMING_5		0x03402400
diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h
index 05bb51f545e..45db5cf873c 100644
--- a/include/configs/km/km-mpc83xx.h
+++ b/include/configs/km/km-mpc83xx.h
@@ -18,7 +18,6 @@
 /*
  * Manually set up DDR parameters
  */
-#define CONFIG_DDR_II
 #define CONFIG_SYS_DDR_SIZE		2048 /* MB */
 
 /*
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 131f6147827..bca5b6af92c 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -72,7 +72,6 @@
 /* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS	0x50	/* CTLR 0 DIMM 0 */
 
-#define CONFIG_DDR_DEFAULT_CL	30		/* CAS latency 3	*/
 
 /* Hardcoded values, to use instead of SPD */
 #define CONFIG_SYS_DDR_CS0_BNDS		0x0000000f
diff --git a/post/cpu/mpc83xx/ecc.c b/post/cpu/mpc83xx/ecc.c
index cc971a89097..f88eff8998f 100644
--- a/post/cpu/mpc83xx/ecc.c
+++ b/post/cpu/mpc83xx/ecc.c
@@ -70,10 +70,6 @@ int ecc_post_test(int flags)
 	int_state = disable_interrupts();
 	icache_enable();
 
-#ifdef CONFIG_DDR_32BIT
-	/* It seems like no one really uses the CONFIG_DDR_32BIT mode */
-#error "Add ECC POST support for CONFIG_DDR_32BIT here!"
-#else
 	for (addr = (u64*)CONFIG_SYS_POST_ECC_START_ADDR, errbit=0;
 	     addr < (u64*)CONFIG_SYS_POST_ECC_STOP_ADDR; addr++, errbit++ ) {
 
@@ -138,7 +134,6 @@ int ecc_post_test(int flags)
 
 		errbit %= 63;
 	}
-#endif /* !CONFIG_DDR_32BIT */
 
 	ecc_clear(ddr);