bosch: Add initial board support for ACC

The Bosch ACC (Air Center Control) Board is based on the i.MX6D.

The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.

[1] Commit 6192cf8ac082 from
    git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git

Signed-off-by: Philip Oberfichtner <pro@denx.de>

4 files changed, 789 insertions, 0 deletions

diff --git a/board/bosch/acc/Kconfig b/board/bosch/acc/Kconfig
new file mode 100644
index 00000000000..da54d96e40e
--- /dev/null
+++ b/board/bosch/acc/Kconfig
@@ -0,0 +1,19 @@
+if TARGET_MX6Q_ACC
+
+config SYS_VENDOR
+	default "bosch"
+
+config SYS_BOARD
+	default "acc"
+
+config SYS_CONFIG_NAME
+	default "imx6q-bosch-acc"
+
+config SYS_BOOT_EMMC
+	bool "Boot from EMMC"
+	default y
+	help
+	  Say N here if you want to boot from SD card or microUSB.
+	  Say Y to boot from eMMC.
+
+endif
diff --git a/board/bosch/acc/MAINTAINERS b/board/bosch/acc/MAINTAINERS
new file mode 100644
index 00000000000..1b880037121
--- /dev/null
+++ b/board/bosch/acc/MAINTAINERS
@@ -0,0 +1,9 @@
+MX6Q_ACC
+M:	Matthias Winker <matthias.winker@de.bosch.com>
+M:	Philip Oberfichtner <pro@denx.de>
+S:	Maintained
+F:	board/bosch/acc
+F:	include/configs/imx6q-bosch-acc.h
+F:	configs/imx6q_bosch_acc_defconfig
+F:	arch/arm/dts/imx6q-bosch-acc.dts
+F:	arch/arm/dts/imx6q-bosch-acc-u-boot.dts
diff --git a/board/bosch/acc/Makefile b/board/bosch/acc/Makefile
new file mode 100644
index 00000000000..d425a677bc9
--- /dev/null
+++ b/board/bosch/acc/Makefile
@@ -0,0 +1,6 @@
+# Copyright (C) 2017
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := acc.o
diff --git a/board/bosch/acc/acc.c b/board/bosch/acc/acc.c
new file mode 100644
index 00000000000..dbc03c9371f
--- /dev/null
+++ b/board/bosch/acc/acc.c
@@ -0,0 +1,755 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2017 DENX Software Engineering GmbH, Heiko Schocher <hs@denx.de>
+ * Copyright (c) 2019 Bosch Thermotechnik GmbH
+ * Copyright (c) 2022 DENX Software Engineering GmbH, Philip Oberfichtner <pro@denx.de>
+ */
+
+#include <common.h>
+#include <bootstage.h>
+#include <dm.h>
+#include <dm/platform_data/serial_mxc.h>
+#include <dm/device-internal.h>
+#include <env.h>
+#include <env_internal.h>
+#include <hang.h>
+#include <init.h>
+#include <linux/delay.h>
+#include <mmc.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/sizes.h>
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+#include <fuse.h>
+
+#include <watchdog.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define GPIO_ACC_PLAT_DETECT     IMX_GPIO_NR(5, 9)
+#define GPIO_ACC_RAM_VOLT_DETECT IMX_GPIO_NR(5, 0)
+#define GPIO_BUZZER              IMX_GPIO_NR(1, 18)
+#define GPIO_LAN1_RESET          IMX_GPIO_NR(4, 27)
+#define GPIO_LAN2_RESET          IMX_GPIO_NR(4, 19)
+#define GPIO_LAN3_RESET          IMX_GPIO_NR(4, 18)
+#define GPIO_USB_HUB_RESET       IMX_GPIO_NR(5, 5)
+#define GPIO_EXP_RS485_RESET     IMX_GPIO_NR(4, 16)
+#define GPIO_TOUCH_RESET         IMX_GPIO_NR(1, 20)
+
+#define BOARD_INFO_MAGIC 0x19730517
+
+struct board_info {
+	int magic;
+	int board;
+	int rev;
+};
+
+static struct board_info *detect_board(void);
+
+#define PFID_BOARD_ACC 0xe
+
+static const char * const name_board[] = {
+	[PFID_BOARD_ACC] = "ACC",
+};
+
+#define PFID_REV_22 0x8
+#define PFID_REV_21 0x9
+#define PFID_REV_20 0xa
+#define PFID_REV_14 0xb
+#define PFID_REV_13 0xc
+#define PFID_REV_12 0xd
+#define PFID_REV_11 0xe
+#define PFID_REV_10 0xf
+
+static const char * const name_revision[] = {
+	[0 ... PFID_REV_10] = "Unknown",
+	[PFID_REV_10] = "1.0",
+	[PFID_REV_11] = "1.1",
+	[PFID_REV_12] = "1.2",
+	[PFID_REV_13] = "1.3",
+	[PFID_REV_14] = "1.4",
+	[PFID_REV_20] = "2.0",
+	[PFID_REV_21] = "2.1",
+	[PFID_REV_22] = "2.2",
+};
+
+/*
+ * NXP Reset Default: 0x0001B0B0
+ * - Schmitt trigger input (PAD_CTL_HYS)
+ * - 100K Ohm Pull Up (PAD_CTL_PUS_100K_UP)
+ * - Pull Enabled (PAD_CTL_PUE)
+ * - Pull/Keeper Enabled (PAD_CTL_PKE)
+ * - CMOS output (No PAD_CTL_ODE)
+ * - Medium Speed (PAD_CTL_SPEED_MED)
+ * - 40 Ohm drive strength (PAD_CTL_DSE_40ohm)
+ * - Slow (PAD_CTL_SRE_SLOW)
+ */
+
+/* Input, no pull up/down: 0x0x000100B0 */
+#define GPIN_PAD_CTRL (PAD_CTL_HYS \
+		| PAD_CTL_SPEED_MED \
+		| PAD_CTL_DSE_40ohm \
+		| PAD_CTL_SRE_SLOW)
+
+/* Input, pull up: 0x0x0001B0B0 */
+#define GPIN_PU_PAD_CTRL (PAD_CTL_HYS \
+		| PAD_CTL_PUS_100K_UP \
+		| PAD_CTL_PUE \
+		| PAD_CTL_PKE \
+		| PAD_CTL_SPEED_MED \
+		| PAD_CTL_DSE_40ohm \
+		| PAD_CTL_SRE_SLOW)
+
+/* Input, pull down: 0x0x000130B0 */
+#define GPIN_PD_PAD_CTRL (PAD_CTL_HYS \
+		| PAD_CTL_PUS_100K_DOWN \
+		| PAD_CTL_PUE \
+		| PAD_CTL_PKE \
+		| PAD_CTL_SPEED_MED \
+		| PAD_CTL_DSE_40ohm \
+		| PAD_CTL_SRE_SLOW)
+
+static const iomux_v3_cfg_t board_detect_pads[] = {
+	/* Platform detect */
+	IOMUX_PADS(PAD_DISP0_DAT15__GPIO5_IO09 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	/* RAM Volt detect */
+	IOMUX_PADS(PAD_EIM_WAIT__GPIO5_IO00 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	/* PFID 0..9 */
+	IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D1__GPIO2_IO01 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D3__GPIO2_IO03 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_D7__GPIO2_IO07 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	/* Manufacturer */
+	IOMUX_PADS(PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(GPIN_PAD_CTRL)),
+	/* Redundant */
+	IOMUX_PADS(PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(GPIN_PU_PAD_CTRL))
+};
+
+static int gpio_acc_pfid[] = {
+	IMX_GPIO_NR(2, 0),
+	IMX_GPIO_NR(2, 1),
+	IMX_GPIO_NR(2, 2),
+	IMX_GPIO_NR(2, 3),
+	IMX_GPIO_NR(2, 4),
+	IMX_GPIO_NR(6, 14),
+	IMX_GPIO_NR(6, 15),
+	IMX_GPIO_NR(2, 5),
+	IMX_GPIO_NR(2, 6),
+	IMX_GPIO_NR(2, 7),
+	IMX_GPIO_NR(6, 16),
+	IMX_GPIO_NR(5, 4),
+};
+
+static int init_gpio(int nr)
+{
+	int ret;
+
+	ret = gpio_request(nr, "");
+	if (ret != 0) {
+		printf("Could not request gpio nr: %d\n", nr);
+		hang();
+	}
+	ret = gpio_direction_input(nr);
+	if (ret != 0) {
+		printf("Could not set gpio nr: %d to input\n", nr);
+		hang();
+	}
+	return 0;
+}
+
+/*
+ * We want to detect the board type only once in SPL,
+ * so we store the board_info struct at beginning in IRAM.
+ *
+ * U-Boot itself can read it also, and do not need again
+ * to detect board type.
+ *
+ */
+static struct board_info *detect_board(void)
+{
+	struct board_info *binfo = (struct board_info *)IRAM_BASE_ADDR;
+	int i;
+
+	if (binfo->magic == BOARD_INFO_MAGIC)
+		return binfo;
+
+	puts("Board: ");
+	SETUP_IOMUX_PADS(board_detect_pads);
+	init_gpio(GPIO_ACC_PLAT_DETECT);
+	if (gpio_get_value(GPIO_ACC_PLAT_DETECT)) {
+		puts("not supported");
+		hang();
+	} else {
+		puts("Bosch ");
+	}
+
+	for (i = 0; i < sizeof(gpio_acc_pfid) / sizeof(int); i++)
+		init_gpio(gpio_acc_pfid[i]);
+
+	binfo->board = gpio_get_value(gpio_acc_pfid[0]) << 0 |
+	    gpio_get_value(gpio_acc_pfid[1]) << 1 |
+	    gpio_get_value(gpio_acc_pfid[2]) << 2 |
+	    gpio_get_value(gpio_acc_pfid[11]) << 3;
+	printf("%s ", name_board[binfo->board]);
+
+	binfo->rev = gpio_get_value(gpio_acc_pfid[7]) << 0 |
+	    gpio_get_value(gpio_acc_pfid[8]) << 1 |
+	    gpio_get_value(gpio_acc_pfid[9]) << 2 |
+	    gpio_get_value(gpio_acc_pfid[10]) << 3;
+	printf("rev: %s\n", name_revision[binfo->rev]);
+
+	binfo->magic = BOARD_INFO_MAGIC;
+
+	return binfo;
+}
+
+static void unset_early_gpio(void)
+{
+	init_gpio(GPIO_LAN1_RESET);
+	init_gpio(GPIO_LAN2_RESET);
+	init_gpio(GPIO_LAN3_RESET);
+	init_gpio(GPIO_USB_HUB_RESET);
+	init_gpio(GPIO_EXP_RS485_RESET);
+	init_gpio(GPIO_TOUCH_RESET);
+
+	gpio_set_value(GPIO_LAN1_RESET, 1);
+	gpio_set_value(GPIO_LAN2_RESET, 1);
+	gpio_set_value(GPIO_LAN3_RESET, 1);
+	gpio_set_value(GPIO_USB_HUB_RESET, 1);
+	gpio_set_value(GPIO_EXP_RS485_RESET, 1);
+	gpio_set_value(GPIO_TOUCH_RESET, 1);
+}
+
+enum env_location env_get_location(enum env_operation op, int prio)
+{
+	if (op == ENVOP_SAVE || op == ENVOP_ERASE)
+		return ENVL_MMC;
+
+	switch (prio) {
+	case 0:
+		return ENVL_NOWHERE;
+
+	case 1:
+		return ENVL_MMC;
+	}
+
+	return ENVL_UNKNOWN;
+}
+
+int board_late_init(void)
+{
+	struct board_info *binfo = detect_board();
+
+	switch (binfo->board) {
+	case PFID_BOARD_ACC:
+		env_set("bootconf", "conf-imx6q-bosch-acc.dtb");
+		break;
+	default:
+		printf("Unknown board %d\n", binfo->board);
+		break;
+	}
+
+	unset_early_gpio();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+#if IS_ENABLED(CONFIG_SPL_BUILD)
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <spl.h>
+
+/* Early
+ * - Buzzer -> GPIO IN, Pull-Down (PWM enabled by Kernel later-on, lacks of an
+ *   external pull-down resistor)
+ * - Touch clean reset on every boot
+ * - Ethernet(s), USB Hub, Expansion RS485 -> Clean reset on each u-boot init
+ */
+static const iomux_v3_cfg_t early_pads[] = {
+	IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* Buzzer PWM */
+	IOMUX_PADS(PAD_DISP0_DAT6__GPIO4_IO27 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* #FEC_RESET_B */
+	IOMUX_PADS(PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* #ETH1_RESET */
+	IOMUX_PADS(PAD_DI0_PIN3__GPIO4_IO19 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* #ETH2_RESET */
+	IOMUX_PADS(PAD_DISP0_DAT11__GPIO5_IO05 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* #USB Reset */
+	IOMUX_PADS(PAD_DI0_DISP_CLK__GPIO4_IO16 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* #UART_RESET */
+	IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(GPIN_PD_PAD_CTRL)), /* #CTOUCH_RESET */
+};
+
+static void setup_iomux_early(void)
+{
+	SETUP_IOMUX_PADS(early_pads);
+}
+
+static void set_early_gpio(void)
+{
+	init_gpio(GPIO_BUZZER);
+	init_gpio(GPIO_LAN1_RESET);
+	init_gpio(GPIO_LAN2_RESET);
+	init_gpio(GPIO_LAN3_RESET);
+	init_gpio(GPIO_USB_HUB_RESET);
+	init_gpio(GPIO_EXP_RS485_RESET);
+	init_gpio(GPIO_TOUCH_RESET);
+
+	/* Reset signals are active low */
+	gpio_set_value(GPIO_BUZZER, 0);
+	gpio_set_value(GPIO_LAN1_RESET, 0);
+	gpio_set_value(GPIO_LAN2_RESET, 0);
+	gpio_set_value(GPIO_LAN3_RESET, 0);
+	gpio_set_value(GPIO_USB_HUB_RESET, 0);
+	gpio_set_value(GPIO_EXP_RS485_RESET, 0);
+	gpio_set_value(GPIO_TOUCH_RESET, 0);
+}
+
+/* UART */
+#define UART_PAD_CTRL \
+		(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+		PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#undef UART_PAD_CTRL
+#define UART_PAD_CTRL 0x1b0b1
+static const iomux_v3_cfg_t uart2_pads[] = {
+	IOMUX_PADS(PAD_SD3_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD3_DAT5__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD3_CMD__UART2_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD3_CLK__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static void setup_iomux_uart(void)
+{
+	SETUP_IOMUX_PADS(uart2_pads);
+}
+
+void spl_board_init(void)
+{
+}
+
+static const struct mx6dq_iomux_ddr_regs acc_mx6d_ddr_ioregs = {
+	.dram_sdclk_0 = 0x00008038,
+	.dram_sdclk_1 = 0x00008038,
+	.dram_cas = 0x00008028,
+	.dram_ras = 0x00008028,
+	.dram_reset = 0x00000028,
+	.dram_sdcke0 = 0x00003000,
+	.dram_sdcke1 = 0x00003000,
+	.dram_sdba2 = 0x00008000,
+	.dram_sdodt0 = 0x00000028,
+	.dram_sdodt1 = 0x00000028,
+	.dram_sdqs0 = 0x00008038,
+	.dram_sdqs1 = 0x00008038,
+	.dram_sdqs2 = 0x00008038,
+	.dram_sdqs3 = 0x00008038,
+	.dram_sdqs4 = 0x00008038,
+	.dram_sdqs5 = 0x00008038,
+	.dram_sdqs6 = 0x00008038,
+	.dram_sdqs7 = 0x00008038,
+	.dram_dqm0 = 0x00008038,
+	.dram_dqm1 = 0x00008038,
+	.dram_dqm2 = 0x00008038,
+	.dram_dqm3 = 0x00008038,
+	.dram_dqm4 = 0x00008038,
+	.dram_dqm5 = 0x00008038,
+	.dram_dqm6 = 0x00008038,
+	.dram_dqm7 = 0x00008038,
+};
+
+static const struct mx6dq_iomux_grp_regs acc_mx6d_grp_ioregs = {
+	.grp_ddr_type = 0x000C0000,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_ddrpke = 0x00000000,
+	.grp_addds = 0x00000030,
+	.grp_ctlds = 0x00000028,
+	.grp_ddrmode = 0x00020000,
+	.grp_b0ds = 0x00000038,
+	.grp_b1ds = 0x00000038,
+	.grp_b2ds = 0x00000038,
+	.grp_b3ds = 0x00000038,
+	.grp_b4ds = 0x00000038,
+	.grp_b5ds = 0x00000038,
+	.grp_b6ds = 0x00000038,
+	.grp_b7ds = 0x00000038,
+};
+
+static const struct mx6_mmdc_calibration acc_mx6d_mmdc_calib = {
+	.p0_mpwldectrl0 = 0x0020001F,
+	.p0_mpwldectrl1 = 0x00280021,
+	.p1_mpwldectrl0 = 0x00120028,
+	.p1_mpwldectrl1 = 0x000D001F,
+	.p0_mpdgctrl0 = 0x43340342,
+	.p0_mpdgctrl1 = 0x03300325,
+	.p1_mpdgctrl0 = 0x4334033E,
+	.p1_mpdgctrl1 = 0x03280270,
+	.p0_mprddlctl = 0x46373B3E,
+	.p1_mprddlctl = 0x3B383544,
+	.p0_mpwrdlctl = 0x36383E40,
+	.p1_mpwrdlctl = 0x4030433A,
+};
+
+/* Micron MT41K128M16JT-125 (standard - 1600,CL=11)
+ * !!! i.MX6 does NOT support data rates higher than DDR3-1066 !!!
+ * So this setting is actually invalid!
+ *
+static const struct mx6_ddr3_cfg acc_mx6d_mem_ddr3_1600 = {
+	.mem_speed = 1600,
+	.density = 2,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+	.SRT = 0,
+};
+ */
+
+/* Micron MT41K128M16JT-125 is backward-compatible with 1333,CL=9 (-15E) and 1066,CL=7 (-187E)
+ * Lowering to 1066 saves on ACC ~0.25 Watt at DC In with negligible performance loss
+ * width set to 64, as four chips are used on acc (4 * 16 = 64)
+ */
+static const struct mx6_ddr3_cfg acc_mx6d_mem_ddr3_1066 = {
+	.mem_speed = 1066,
+	.density = 2,
+	.width = 64,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1313, // 13.125ns
+	.trcmin = 5063, // 50.625ns
+	.trasmin = 3750, // 37.5ns
+	.SRT = 0, // Set to 1 for temperatures above 85°C
+};
+
+static const struct mx6_ddr_sysinfo acc_mx6d_ddr_info = {
+	.ddr_type = DDR_TYPE_DDR3,
+	/* width of data bus:0=16,1=32,2=64 */
+	.dsize = 2,
+	.cs_density = 32,	/* 32Gb per CS */
+	.ncs = 1,		/* single chip select */
+	.cs1_mirror = 0,
+	.rtt_wr = 1,		/* DDR3_RTT_60_OHM, RTT_Wr = RZQ/4 */
+	.rtt_nom = 1,		/* DDR3_RTT_60_OHM, RTT_Nom = RZQ/4 */
+	.walat = 0,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x33,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x33,	/* 33 cycles, 500us (JEDEC default) */
+};
+
+#define ACC_SPREAD_SPECTRUM_STOP	0x0fa
+#define ACC_SPREAD_SPECTRUM_STEP	0x001
+#define ACC_SPREAD_SPECTRUM_DENOM	0x190
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* Turn clocks on/off */
+	writel(0x00C0000F, &ccm->CCGR0);
+	writel(0x0030FC00, &ccm->CCGR1);
+	writel(0x03FF0033, &ccm->CCGR2);
+	writel(0x3FF3300F, &ccm->CCGR3);
+	writel(0x0003C300, &ccm->CCGR4);
+	writel(0x0F3000C3, &ccm->CCGR5);
+	writel(0x00000FFF, &ccm->CCGR6);
+
+	/* Enable spread spectrum */
+	writel(BM_ANADIG_PLL_528_SS_ENABLE |
+	       BF_ANADIG_PLL_528_SS_STOP(ACC_SPREAD_SPECTRUM_STOP) |
+	       BF_ANADIG_PLL_528_SS_STEP(ACC_SPREAD_SPECTRUM_STEP),
+	       &ccm->analog_pll_528_ss);
+
+	writel(BF_ANADIG_PLL_528_DENOM_B(ACC_SPREAD_SPECTRUM_DENOM),
+	       &ccm->analog_pll_528_denom);
+}
+
+/* MMC board initialization is needed till adding DM support in SPL */
+#if IS_ENABLED(CONFIG_FSL_ESDHC_IMX) && !IS_ENABLED(CONFIG_DM_MMC)
+#include <mmc.h>
+#include <fsl_esdhc_imx.h>
+
+static const iomux_v3_cfg_t usdhc2_pads[] = {
+	IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(0x00017069)),
+	IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(0x00010038)),
+	IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(0x00017069)),
+	IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(0x00017069)),
+	IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(0x00017069)),
+	IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(0x00017069)),
+	IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(0x0001B0B0)),	/* CD */
+};
+
+static const iomux_v3_cfg_t usdhc4_pads[] = {
+	IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(0x00010059)),
+	IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(0x00017059)),
+	IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(0x00017059)),
+};
+
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC2_BASE_ADDR, 1, 4},
+	{USDHC4_BASE_ADDR, 1, 8},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	detect_board();
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		return !gpio_get_value(USDHC2_CD_GPIO);
+	case USDHC4_BASE_ADDR:
+		return 1;	/* eMMC always present */
+	}
+
+	return ret;
+}
+
+int board_mmc_init(struct bd_info *bis)
+{
+	int i, ret;
+
+	gpio_direction_input(USDHC2_CD_GPIO);
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node) (Physical Port)
+	 * mmc0 USDHC2
+	 * mmc1 USDHC4
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			SETUP_IOMUX_PADS(usdhc2_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			SETUP_IOMUX_PADS(usdhc4_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+#endif
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	u32 bmode = imx6_src_get_boot_mode();
+	u8 boot_dev = BOOT_DEVICE_MMC1;
+
+	detect_board();
+
+	switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
+	case IMX6_BMODE_SD:
+	case IMX6_BMODE_ESD:
+		/* SD/eSD - BOOT_DEVICE_MMC1 */
+		if (IS_ENABLED(CONFIG_SYS_BOOT_EMMC)) {
+			/*
+			 * boot from SD is not allowed, if boot from eMMC is
+			 * configured.
+			 */
+			puts("SD boot not allowed\n");
+			spl_boot_list[0] = BOOT_DEVICE_NONE;
+			return;
+		}
+
+		boot_dev = BOOT_DEVICE_MMC1;
+		break;
+
+	case IMX6_BMODE_MMC:
+	case IMX6_BMODE_EMMC:
+		/* MMC/eMMC */
+		boot_dev = BOOT_DEVICE_MMC2;
+		break;
+	default:
+		/* Default - BOOT_DEVICE_MMC1 */
+		printf("Wrong board boot order\n");
+		break;
+	}
+
+	spl_boot_list[0] = boot_dev;
+}
+
+static void setup_ddr(void)
+{
+	struct board_info *binfo = detect_board();
+
+	switch (binfo->rev) {
+	case PFID_REV_20:
+	case PFID_REV_21:
+	case PFID_REV_22:
+	default:
+		/* Rev 2 board has i.MX6 Dual with 64-bit RAM */
+		mx6dq_dram_iocfg(acc_mx6d_mem_ddr3_1066.width,
+				 &acc_mx6d_ddr_ioregs,
+				 &acc_mx6d_grp_ioregs);
+		mx6_dram_cfg(&acc_mx6d_ddr_info, &acc_mx6d_mmdc_calib,
+			     &acc_mx6d_mem_ddr3_1066);
+		/* Perform DDR DRAM calibration */
+		udelay(100);
+		mmdc_do_write_level_calibration(&acc_mx6d_ddr_info);
+		mmdc_do_dqs_calibration(&acc_mx6d_ddr_info);
+		break;
+	}
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog power-down counter (only enabled after reset) */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* Enable device tree and early DM support*/
+	spl_early_init();
+
+	/* Setup early required pinmuxes */
+	setup_iomux_early();
+	set_early_gpio();
+
+	/* Setup UART pinmux */
+	setup_iomux_uart();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	setup_ddr();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+#endif
+
+#if IS_ENABLED(CONFIG_USB_EHCI_MX6)
+#define USB_OTHERREGS_OFFSET	0x800
+#define UCTRL_PWR_POL		BIT(9)
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return usb_phy_mode(port);
+}
+
+int board_ehci_hcd_init(int port)
+{
+	u32 *usbnc_usb_ctrl;
+
+	if (port > 1)
+		return -EINVAL;
+
+	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+				  port * 4);
+
+	/* Set Power polarity */
+	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+	return 0;
+}
+#endif
+
+int board_fit_config_name_match(const char *name)
+{
+	if (!strcmp(name, "imx6q-bosch-acc"))
+		return 0;
+	return -1;
+}
+
+void reset_cpu(ulong addr)
+{
+	puts("Hanging CPU for watchdog reset!\n");
+	hang();
+}
+
+#if CONFIG_IS_ENABLED(SHOW_BOOT_PROGRESS)
+void show_boot_progress(int val)
+{
+	u32 fuseval;
+	int ret;
+
+	if (val < 0)
+		val *= -1;
+
+	switch (val) {
+	case BOOTSTAGE_ID_ENTER_CLI_LOOP:
+		printf("autoboot failed, check fuse\n");
+		ret = fuse_read(0, 6, &fuseval);
+		if (ret == 0 && (fuseval & 0x2) == 0x0) {
+			printf("Enter cmdline, as device not closed\n");
+			return;
+		}
+		ret = fuse_read(5, 7, &fuseval);
+		if (ret == 0 && fuseval == 0x0) {
+			printf("Enter cmdline, as it is a Development device\n");
+			return;
+		}
+		panic("do not enter cmdline");
+		break;
+	}
+}
+#endif