Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

39 files changed, 1503 insertions, 77 deletions

diff --git a/board/freescale/b4860qds/Makefile b/board/freescale/b4860qds/Makefile
index e5cc054a015..0acd2a9aa4a 100644
--- a/board/freescale/b4860qds/Makefile
+++ b/board/freescale/b4860qds/Makefile
@@ -4,9 +4,14 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-y	+= b4860qds.o
-obj-y	+= ddr.o
 obj-$(CONFIG_B4860QDS)+= eth_b4860qds.o
-obj-$(CONFIG_PCI)	+= pci.o
+obj-$(CONFIG_PCI)      += pci.o
+endif
+
+obj-y	+= ddr.o
 obj-y	+= law.o
 obj-y	+= tlb.o
diff --git a/board/freescale/b4860qds/b4_pbi.cfg b/board/freescale/b4860qds/b4_pbi.cfg
index 57b726eead8..05377bac5bb 100644
--- a/board/freescale/b4860qds/b4_pbi.cfg
+++ b/board/freescale/b4860qds/b4_pbi.cfg
@@ -22,6 +22,9 @@
 09110024 00100008
 09110028 00100008
 0911002c 00100008
+#slowing down the MDC clock to make it <= 2.5 MHZ
+094fc030 00008148
+094fd030 00008148
 #Flush PBL data
 09138000 00000000
 091380c0 00000000
diff --git a/board/freescale/b4860qds/ddr.c b/board/freescale/b4860qds/ddr.c
index 187c3b3ebca..2c17156586d 100644
--- a/board/freescale/b4860qds/ddr.c
+++ b/board/freescale/b4860qds/ddr.c
@@ -179,6 +179,7 @@ phys_size_t initdram(int board_type)
 {
 	phys_size_t dram_size;
 
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 	puts("Initializing....using SPD\n");
 
 	dram_size = fsl_ddr_sdram();
@@ -186,7 +187,9 @@ phys_size_t initdram(int board_type)
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
 
-	puts("    DDR: ");
+#else
+	dram_size =  fsl_ddr_sdram_size();
+#endif
 	return dram_size;
 }
 
diff --git a/board/freescale/b4860qds/spl.c b/board/freescale/b4860qds/spl.c
new file mode 100644
index 00000000000..3aa5a780f4b
--- /dev/null
+++ b/board/freescale/b4860qds/spl.c
@@ -0,0 +1,114 @@
+/* Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/spl.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include "../common/qixis.h"
+#include "b4860qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch ((sysclk_conf & 0x0C) >> 2) {
+	case QIXIS_CLK_100:
+		return 100000000;
+	case QIXIS_CLK_125:
+		return 125000000;
+	case QIXIS_CLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (ddrclk_conf & 0x03) {
+	case QIXIS_CLK_100:
+		return 100000000;
+	case QIXIS_CLK_125:
+		return 125000000;
+	case QIXIS_CLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, uart_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	/* compiler optimization barrier needed for GCC >= 3.4 */
+	__asm__ __volatile__("" : : : "memory");
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	uart_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     uart_clk / 16 / CONFIG_BAUDRATE);
+
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifndef CONFIG_SPL_NAND_BOOT
+	env_init();
+	env_relocate();
+#else
+	/* relocate environment function pointers etc. */
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+#endif
+
+	i2c_init_all();
+
+	puts("\n\n");
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/b4860qds/tlb.c b/board/freescale/b4860qds/tlb.c
index 00798a1c190..7b55b860d08 100644
--- a/board/freescale/b4860qds/tlb.c
+++ b/board/freescale/b4860qds/tlb.c
@@ -62,6 +62,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
 		      0, 2, BOOKE_PAGESZ_256M, 1),
 
+#ifndef CONFIG_SPL_BUILD
 	/* *I*G* - PCI */
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -96,6 +97,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 9, BOOKE_PAGESZ_16M, 1),
 #endif
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -118,6 +120,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	 * entry 14 and 15 has been used hard coded, they will be disabled
 	 * in cpu_init_f, so we use entry 16 for SRIO2.
 	 */
+#ifndef CONFIG_SPL_BUILD
 #ifdef CONFIG_SYS_SRIO1_MEM_PHYS
 	/* *I*G* - SRIO1 */
 	SET_TLB_ENTRY(1, CONFIG_SYS_SRIO1_MEM_VIRT, CONFIG_SYS_SRIO1_MEM_PHYS,
@@ -140,6 +143,13 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
 		      0, 17, BOOKE_PAGESZ_1M, 1),
 #endif
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 17, BOOKE_PAGESZ_2G, 1)
+#endif
 };
 
 int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/qemu-ppce500/Makefile b/board/freescale/qemu-ppce500/Makefile
new file mode 100644
index 00000000000..2d2749205f1
--- /dev/null
+++ b/board/freescale/qemu-ppce500/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	+= qemu-ppce500.o
diff --git a/board/freescale/qemu-ppce500/qemu-ppce500.c b/board/freescale/qemu-ppce500/qemu-ppce500.c
new file mode 100644
index 00000000000..3dbb0cf43b8
--- /dev/null
+++ b/board/freescale/qemu-ppce500/qemu-ppce500.c
@@ -0,0 +1,348 @@
+/*
+ * Copyright 2007,2009-2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/fsl_pci.h>
+#include <asm/io.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <netdev.h>
+#include <fdtdec.h>
+#include <errno.h>
+#include <malloc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void *get_fdt_virt(void)
+{
+	return (void *)CONFIG_SYS_TMPVIRT;
+}
+
+static uint64_t get_fdt_phys(void)
+{
+	return (uint64_t)(uintptr_t)gd->fdt_blob;
+}
+
+static void map_fdt_as(int esel)
+{
+	u32 mas0, mas1, mas2, mas3, mas7;
+	uint64_t fdt_phys = get_fdt_phys();
+	unsigned long fdt_phys_tlb = fdt_phys & ~0xffffful;
+	unsigned long fdt_virt_tlb = (ulong)get_fdt_virt() & ~0xffffful;
+
+	mas0 = MAS0_TLBSEL(1) | MAS0_ESEL(esel);
+	mas1 = MAS1_VALID | MAS1_TID(0) | MAS1_TS | MAS1_TSIZE(BOOKE_PAGESZ_1M);
+	mas2 = FSL_BOOKE_MAS2(fdt_virt_tlb, 0);
+	mas3 = FSL_BOOKE_MAS3(fdt_phys_tlb, 0, MAS3_SW|MAS3_SR);
+	mas7 = FSL_BOOKE_MAS7(fdt_phys_tlb);
+
+	write_tlb(mas0, mas1, mas2, mas3, mas7);
+}
+
+uint64_t get_phys_ccsrbar_addr_early(void)
+{
+	void *fdt = get_fdt_virt();
+	uint64_t r;
+
+	/*
+	 * To be able to read the FDT we need to create a temporary TLB
+	 * map for it.
+	 */
+	map_fdt_as(10);
+	r = fdt_get_base_address(fdt, fdt_path_offset(fdt, "/soc"));
+	disable_tlb(10);
+
+	return r;
+}
+
+int board_early_init_f(void)
+{
+	return 0;
+}
+
+int checkboard(void)
+{
+	return 0;
+}
+
+static int pci_map_region(void *fdt, int pci_node, int range_id,
+			  phys_size_t *ppaddr, pci_addr_t *pvaddr,
+			  pci_size_t *psize, ulong *pmap_addr)
+{
+	uint64_t addr;
+	uint64_t size;
+	ulong map_addr;
+	int r;
+
+	r = fdt_read_range(fdt, pci_node, 0, NULL, &addr, &size);
+	if (r)
+		return r;
+
+	if (ppaddr)
+		*ppaddr = addr;
+	if (psize)
+		*psize = size;
+
+	if (!pmap_addr)
+		return 0;
+
+	map_addr = *pmap_addr;
+
+	/* Align map_addr */
+	map_addr += size - 1;
+	map_addr &= ~(size - 1);
+
+	if (map_addr + size >= CONFIG_SYS_PCI_MAP_END)
+		return -1;
+
+	/* Map virtual memory for range */
+	assert(!tlb_map_range(map_addr, addr, size, TLB_MAP_IO));
+	*pmap_addr = map_addr + size;
+
+	if (pvaddr)
+		*pvaddr = map_addr;
+
+	return 0;
+}
+
+void pci_init_board(void)
+{
+	struct pci_controller *pci_hoses;
+	void *fdt = get_fdt_virt();
+	int pci_node = -1;
+	int pci_num = 0;
+	int pci_count = 0;
+	ulong map_addr;
+
+	puts("\n");
+
+	/* Start MMIO and PIO range maps above RAM */
+	map_addr = CONFIG_SYS_PCI_MAP_START;
+
+	/* Count and allocate PCI buses */
+	pci_node = fdt_node_offset_by_prop_value(fdt, pci_node,
+			"device_type", "pci", 4);
+	while (pci_node != -FDT_ERR_NOTFOUND) {
+		pci_node = fdt_node_offset_by_prop_value(fdt, pci_node,
+				"device_type", "pci", 4);
+		pci_count++;
+	}
+
+	if (pci_count) {
+		pci_hoses = malloc(sizeof(struct pci_controller) * pci_count);
+	} else {
+		printf("PCI: disabled\n\n");
+		return;
+	}
+
+	/* Spawn PCI buses based on device tree */
+	pci_node = fdt_node_offset_by_prop_value(fdt, pci_node,
+			"device_type", "pci", 4);
+	while (pci_node != -FDT_ERR_NOTFOUND) {
+		struct fsl_pci_info pci_info = { };
+		const fdt32_t *reg;
+		int r;
+
+		reg = fdt_getprop(fdt, pci_node, "reg", NULL);
+		pci_info.regs = fdt_translate_address(fdt, pci_node, reg);
+
+		/* Map MMIO range */
+		r = pci_map_region(fdt, pci_node, 0, &pci_info.mem_phys, NULL,
+				   &pci_info.mem_size, &map_addr);
+		if (r)
+			break;
+
+		/* Map PIO range */
+		r = pci_map_region(fdt, pci_node, 1, &pci_info.io_phys, NULL,
+				   &pci_info.io_size, &map_addr);
+		if (r)
+			break;
+
+		/*
+		 * The PCI framework finds virtual addresses for the buses
+		 * through our address map, so tell it the physical addresses.
+		 */
+		pci_info.mem_bus = pci_info.mem_phys;
+		pci_info.io_bus = pci_info.io_phys;
+
+		/* Instantiate */
+		pci_info.pci_num = pci_num + 1;
+
+		fsl_setup_hose(&pci_hoses[pci_num], pci_info.regs);
+		printf("PCI: base address %lx\n", pci_info.regs);
+
+		fsl_pci_init_port(&pci_info, &pci_hoses[pci_num], pci_num);
+
+		/* Jump to next PCI node */
+		pci_node = fdt_node_offset_by_prop_value(fdt, pci_node,
+				"device_type", "pci", 4);
+		pci_num++;
+	}
+
+	puts("\n");
+}
+
+int last_stage_init(void)
+{
+	void *fdt = get_fdt_virt();
+	int len = 0;
+	const uint64_t *prop;
+	int chosen;
+
+	chosen = fdt_path_offset(fdt, "/chosen");
+	if (chosen < 0) {
+		printf("Couldn't find /chosen node in fdt\n");
+		return -EIO;
+	}
+
+	/* -kernel boot */
+	prop = fdt_getprop(fdt, chosen, "qemu,boot-kernel", &len);
+	if (prop && (len >= 8))
+		setenv_hex("qemu_kernel_addr", *prop);
+
+	/* Give the user a variable for the host fdt */
+	setenv_hex("fdt_addr_r", (ulong)fdt);
+
+	return 0;
+}
+
+static uint64_t get_linear_ram_size(void)
+{
+	void *fdt = get_fdt_virt();
+	const void *prop;
+	int memory;
+	int len;
+
+	memory = fdt_path_offset(fdt, "/memory");
+	prop = fdt_getprop(fdt, memory, "reg", &len);
+
+	if (prop && len >= 16)
+		return *(uint64_t *)(prop+8);
+
+	panic("Couldn't determine RAM size");
+}
+
+int board_eth_init(bd_t *bis)
+{
+	return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
+#endif
+
+void print_laws(void)
+{
+	/* We don't emulate LAWs yet */
+}
+
+phys_size_t fixed_sdram(void)
+{
+	return get_linear_ram_size();
+}
+
+phys_size_t fsl_ddr_sdram_size(void)
+{
+	return get_linear_ram_size();
+}
+
+void init_tlbs(void)
+{
+	phys_size_t ram_size;
+
+	/*
+	 * Create a temporary AS=1 map for the fdt
+	 *
+	 * We use ESEL=0 here to overwrite the previous AS=0 map for ourselves
+	 * which was only 4k big. This way we don't have to clear any other maps.
+	 */
+	map_fdt_as(0);
+
+	/* Fetch RAM size from the fdt */
+	ram_size = get_linear_ram_size();
+
+	/* And remove our fdt map again */
+	disable_tlb(0);
+
+	/* Create an internal map of manually created TLB maps */
+	init_used_tlb_cams();
+
+	/* Create a dynamic AS=0 CCSRBAR mapping */
+	assert(!tlb_map_range(CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+			      1024 * 1024, TLB_MAP_IO));
+
+	/* Create a RAM map that spans all accessible RAM */
+	setup_ddr_tlbs(ram_size >> 20);
+
+	/* Create a map for the TLB */
+	assert(!tlb_map_range((ulong)get_fdt_virt(), get_fdt_phys(),
+			      1024 * 1024, TLB_MAP_RAM));
+}
+
+void init_laws(void)
+{
+	/* We don't emulate LAWs yet */
+}
+
+static uint32_t get_cpu_freq(void)
+{
+	void *fdt = get_fdt_virt();
+	int cpus_node = fdt_path_offset(fdt, "/cpus");
+	int cpu_node = fdt_first_subnode(fdt, cpus_node);
+	const char *prop = "clock-frequency";
+	return fdt_getprop_u32_default_node(fdt, cpu_node, 0, prop, 0);
+}
+
+void get_sys_info(sys_info_t *sys_info)
+{
+	int freq = get_cpu_freq();
+
+	memset(sys_info, 0, sizeof(sys_info_t));
+	sys_info->freq_systembus = freq;
+	sys_info->freq_ddrbus = freq;
+	sys_info->freq_processor[0] = freq;
+}
+
+int get_clocks (void)
+{
+	sys_info_t sys_info;
+
+	get_sys_info(&sys_info);
+
+	gd->cpu_clk = sys_info.freq_processor[0];
+	gd->bus_clk = sys_info.freq_systembus;
+	gd->mem_clk = sys_info.freq_ddrbus;
+	gd->arch.lbc_clk = sys_info.freq_ddrbus;
+
+	return 0;
+}
+
+unsigned long get_tbclk (void)
+{
+	void *fdt = get_fdt_virt();
+	int cpus_node = fdt_path_offset(fdt, "/cpus");
+	int cpu_node = fdt_first_subnode(fdt, cpus_node);
+	const char *prop = "timebase-frequency";
+	return fdt_getprop_u32_default_node(fdt, cpu_node, 0, prop, 0);
+}
+
+/********************************************
+ * get_bus_freq
+ * return system bus freq in Hz
+ *********************************************/
+ulong get_bus_freq (ulong dummy)
+{
+	sys_info_t sys_info;
+	get_sys_info(&sys_info);
+	return sys_info.freq_systembus;
+}
diff --git a/board/freescale/t1040qds/ddr.c b/board/freescale/t1040qds/ddr.c
index da89a36b96a..43f952f9c03 100644
--- a/board/freescale/t1040qds/ddr.c
+++ b/board/freescale/t1040qds/ddr.c
@@ -1,5 +1,5 @@
 /*
- * Copyright 2013 Freescale Semiconductor, Inc.
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -39,14 +39,10 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 		if (pbsp->n_ranks == pdimm->n_ranks &&
 		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
 			if (ddr_freq <= pbsp->datarate_mhz_high) {
-				popts->cpo_override = pbsp->cpo;
-				popts->write_data_delay =
-					pbsp->write_data_delay;
 				popts->clk_adjust = pbsp->clk_adjust;
 				popts->wrlvl_start = pbsp->wrlvl_start;
 				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
 				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-				popts->twot_en = pbsp->force_2t;
 				goto found;
 			}
 			pbsp_highest = pbsp;
@@ -59,13 +55,10 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 		printf("for data rate %lu MT/s\n", ddr_freq);
 		printf("Trying to use the highest speed (%u) parameters\n",
 		       pbsp_highest->datarate_mhz_high);
-		popts->cpo_override = pbsp_highest->cpo;
-		popts->write_data_delay = pbsp_highest->write_data_delay;
 		popts->clk_adjust = pbsp_highest->clk_adjust;
 		popts->wrlvl_start = pbsp_highest->wrlvl_start;
 		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
 		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-		popts->twot_en = pbsp_highest->force_2t;
 	} else {
 		panic("DIMM is not supported by this board");
 	}
@@ -81,7 +74,7 @@ found:
 	 * Factors to consider for half-strength driver enable:
 	 *	- number of DIMMs installed
 	 */
-	popts->half_strength_driver_enable = 0;
+	popts->half_strength_driver_enable = 1;
 	/*
 	 * Write leveling override
 	 */
@@ -97,8 +90,14 @@ found:
 	popts->zq_en = 1;
 
 	/* DHC_EN =1, ODT = 75 Ohm */
+#ifdef CONFIG_SYS_FSL_DDR4
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
+#else
 	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
 	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
 }
 
 phys_size_t initdram(int board_type)
diff --git a/board/freescale/t1040qds/ddr.h b/board/freescale/t1040qds/ddr.h
index afa72af26a6..a6e1673525f 100644
--- a/board/freescale/t1040qds/ddr.h
+++ b/board/freescale/t1040qds/ddr.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2013 Freescale Semiconductor, Inc.
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -14,9 +14,6 @@ struct board_specific_parameters {
 	u32 wrlvl_start;
 	u32 wrlvl_ctl_2;
 	u32 wrlvl_ctl_3;
-	u32 cpo;
-	u32 write_data_delay;
-	u32 force_2t;
 };
 
 /*
@@ -28,21 +25,25 @@ struct board_specific_parameters {
 static const struct board_specific_parameters udimm0[] = {
 	/*
 	 * memory controller 0
-	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
-	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl |
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |
 	 */
-	{2,  833,  4, 4,     6, 0x06060607, 0x08080807,   0xff,    2,  0},
-	{2,  833,  0, 4,     6, 0x06060607, 0x08080807,   0xff,    2,  0},
-	{2,  1350, 4, 4,     7, 0x0708080A, 0x0A0B0C09,   0xff,    2,  0},
-	{2,  1350, 0, 4,     7, 0x0708080A, 0x0A0B0C09,   0xff,    2,  0},
-	{2,  1666, 4, 4,     7, 0x0808090B, 0x0C0D0E0A,   0xff,    2,  0},
-	{2,  1666, 0, 4,     7, 0x0808090B, 0x0C0D0E0A,   0xff,    2,  0},
-	{1,  833,  4, 4,     6, 0x06060607, 0x08080807,   0xff,    2,  0},
-	{1,  833,  0, 4,     6, 0x06060607, 0x08080807,   0xff,    2,  0},
-	{1,  1350, 4, 4,     7, 0x0708080A, 0x0A0B0C09,   0xff,    2,  0},
-	{1,  1350, 0, 4,     7, 0x0708080A, 0x0A0B0C09,   0xff,    2,  0},
-	{1,  1666, 4, 4,     7, 0x0808090B, 0x0C0D0E0A,   0xff,    2,  0},
-	{1,  1666, 0, 4,     7, 0x0808090B, 0x0C0D0E0A,   0xff,    2,  0},
+#ifdef CONFIG_SYS_FSL_DDR4
+	{2,  1666, 0, 4,     7, 0x0808090B, 0x0C0D0E0A,},
+	{2,  1900, 0, 4,     6, 0x08080A0C, 0x0D0E0F0A,},
+	{1,  1666, 0, 4,     6, 0x0708090B, 0x0C0D0E09,},
+	{1,  1900, 0, 4,     6, 0x08080A0C, 0x0D0E0F0A,},
+	{1,  2200, 0, 4,     7, 0x08090A0D, 0x0F0F100C,},
+#elif defined(CONFIG_SYS_FSL_DDR3)
+	{2,  833,  0, 4,     6, 0x06060607, 0x08080807,},
+	{2,  1350, 0, 4,     7, 0x0708080A, 0x0A0B0C09,},
+	{2,  1666, 0, 4,     7, 0x0808090B, 0x0C0D0E0A,},
+	{1,  833,  0, 4,     6, 0x06060607, 0x08080807,},
+	{1,  1350, 0, 4,     7, 0x0708080A, 0x0A0B0C09,},
+	{1,  1666, 0, 4,     7, 0x0808090B, 0x0C0D0E0A,},
+#else
+#error DDR type not defined
+#endif
 	{}
 };
 
diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c
index 3dec4473e52..0e83d172dac 100644
--- a/board/freescale/t1040qds/t1040qds.c
+++ b/board/freescale/t1040qds/t1040qds.c
@@ -18,6 +18,8 @@
 #include <asm/fsl_portals.h>
 #include <asm/fsl_liodn.h>
 #include <fm_eth.h>
+#include <hwconfig.h>
+#include <asm/mpc85xx_gpio.h>
 
 #include "../common/qixis.h"
 #include "t1040qds.h"
@@ -89,6 +91,30 @@ int select_i2c_ch_pca9547(u8 ch)
 	return 0;
 }
 
+static void qe_board_setup(void)
+{
+	u8 brdcfg15, brdcfg9;
+
+	if (hwconfig("qe") && hwconfig("tdm")) {
+		brdcfg15 = QIXIS_READ(brdcfg[15]);
+		/*
+		 * TDMRiser uses QE-TDM
+		 * Route QE_TDM signals to TDM Riser slot
+		 */
+		QIXIS_WRITE(brdcfg[15], brdcfg15 | 7);
+	} else if (hwconfig("qe") && hwconfig("uart")) {
+		brdcfg15 = QIXIS_READ(brdcfg[15]);
+		brdcfg9 = QIXIS_READ(brdcfg[9]);
+		/*
+		 * Route QE_TDM signals to UCC
+		 * ProfiBus controlled by UCC3
+		 */
+		brdcfg15 &= 0xfc;
+		QIXIS_WRITE(brdcfg[15], brdcfg15 | 2);
+		QIXIS_WRITE(brdcfg[9], brdcfg9 | 4);
+	}
+}
+
 int board_early_init_r(void)
 {
 #ifdef CONFIG_SYS_FLASH_BASE
@@ -196,6 +222,8 @@ int misc_init_r(void)
 		}
 	}
 
+	qe_board_setup();
+
 	return 0;
 }
 
@@ -245,3 +273,14 @@ int board_need_mem_reset(void)
 {
 	return 1;
 }
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+	/* does not provide HW signals for power management */
+	QIXIS_WRITE(pwr_ctl[1], (QIXIS_READ(pwr_ctl[1]) & ~0x2));
+	/* Disable MCKE isolation */
+	gpio_set_value(2, 0);
+	udelay(1);
+}
+#endif
diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile
index e51fb7a7f45..6cd304cce91 100644
--- a/board/freescale/t104xrdb/Makefile
+++ b/board/freescale/t104xrdb/Makefile
@@ -4,10 +4,14 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-y	+= t104xrdb.o
-obj-y	+= ddr.o
+obj-y	+= cpld.o
 obj-y	+= eth.o
 obj-$(CONFIG_PCI)	+= pci.o
+endif
+obj-y	+= ddr.o
 obj-y	+= law.o
 obj-y	+= tlb.o
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
index 1da52bb0b00..cdbe1fafd9a 100644
--- a/board/freescale/t104xrdb/README
+++ b/board/freescale/t104xrdb/README
@@ -198,3 +198,76 @@ The below commands apply to the board
 
 	2.To change from vbank4 to vbank0
 		=> qixis reset (it will boot using vbank0)
+
+NAND boot with 2 Stage boot loader
+----------------------------------
+PBL initialise the internal SRAM and copy SPL(160KB) in SRAM.
+SPL further initialise DDR using SPD and environment variables and copy
+u-boot(768 KB) from flash to DDR.
+Finally SPL transer control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+ Run time view of SPL framework during  boot :-
+ -----------------------------------------------
+ Area        | Address                         |
+-----------------------------------------------
+ Secure boot | 0xFFFC0000 (32KB)               |
+ headers     |                                 |
+ -----------------------------------------------
+ GD, BD      | 0xFFFC8000 (4KB)                |
+ -----------------------------------------------
+ ENV         | 0xFFFC9000 (8KB)                |
+ -----------------------------------------------
+ HEAP        | 0xFFFCB000 (30KB)               |
+ -----------------------------------------------
+ STACK       | 0xFFFD8000 (22KB)               |
+ -----------------------------------------------
+ U-boot SPL  | 0xFFFD8000 (160KB)              |
+ -----------------------------------------------
+
+NAND Flash memory Map on T104xRDB
+------------------------------------------
+ Start		 End		Definition			Size
+0x000000	0x0FFFFF	u-boot                          1MB
+0x180000	0x19FFFF	u-boot env                      128KB
+0x280000	0x29FFFF	FMAN Ucode                      128KB
+0x380000	0x39FFFF	QE Firmware                     128KB
+
+SD Card memory Map on T104xRDB
+------------------------------------------
+ Block		#blocks		Definition			Size
+0x008		2048		u-boot                          1MB
+0x800		0024		u-boot env                      8KB
+0x820		0256		FMAN Ucode                      128KB
+0x920		0256		QE Firmware                     128KB
+
+SPI Flash memory Map on T104xRDB
+------------------------------------------
+ Start		 End		Definition			Size
+0x000000	0x0FFFFF	u-boot                          1MB
+0x100000	0x101FFF	u-boot env                      8KB
+0x110000	0x12FFFF	FMAN Ucode                      128KB
+0x130000	0x14FFFF	QE Firmware                     128KB
+
+Please note QE Firmware is only valid for T1040RDB
+
+
+Switch Settings: (ON is 0, OFF is 1)
+===============
+NAND boot SW setting:
+SW1: 10001000
+SW2: 00111001
+SW3: 11110001
+
+SPI boot SW setting:
+SW1: 00100010
+SW2: 10111001
+SW3: 11100001
+
+SD boot SW setting:
+SW1: 00100000
+SW2: 00111001
+SW3: 11100001
diff --git a/board/freescale/t104xrdb/cpld.c b/board/freescale/t104xrdb/cpld.c
new file mode 100644
index 00000000000..df0e348d4af
--- /dev/null
+++ b/board/freescale/t104xrdb/cpld.c
@@ -0,0 +1,112 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * This file provides support for the board-specific CPLD used on some Freescale
+ * reference boards.
+ *
+ * The following macros need to be defined:
+ *
+ * CONFIG_SYS_CPLD_BASE-The virtual address of the base of the CPLD register map
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+	void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+	return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+	void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+	out_8(p + reg, value);
+}
+
+/**
+ * Set the boot bank to the alternate bank
+ */
+void cpld_set_altbank(void)
+{
+	u8 reg = CPLD_READ(flash_ctl_status);
+
+	reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK;
+
+	CPLD_WRITE(flash_ctl_status, reg);
+	CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
+}
+
+/**
+ * Set the boot bank to the default bank
+ */
+void cpld_set_defbank(void)
+{
+	u8 reg = CPLD_READ(flash_ctl_status);
+
+	reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK;
+
+	CPLD_WRITE(flash_ctl_status, reg);
+	CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
+}
+
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+	printf("cpld_ver	 = 0x%02x\n", CPLD_READ(cpld_ver));
+	printf("cpld_ver_sub	 = 0x%02x\n", CPLD_READ(cpld_ver_sub));
+	printf("hw_ver		 = 0x%02x\n", CPLD_READ(hw_ver));
+	printf("sw_ver		 = 0x%02x\n", CPLD_READ(sw_ver));
+	printf("reset_ctl1	 = 0x%02x\n", CPLD_READ(reset_ctl1));
+	printf("reset_ctl2	 = 0x%02x\n", CPLD_READ(reset_ctl2));
+	printf("int_status	 = 0x%02x\n", CPLD_READ(int_status));
+	printf("flash_ctl_status = 0x%02x\n", CPLD_READ(flash_ctl_status));
+	printf("fan_ctl_status	 = 0x%02x\n", CPLD_READ(fan_ctl_status));
+	printf("led_ctl_status	 = 0x%02x\n", CPLD_READ(led_ctl_status));
+	printf("sfp_ctl_status	 = 0x%02x\n", CPLD_READ(sfp_ctl_status));
+	printf("misc_ctl_status	 = 0x%02x\n", CPLD_READ(misc_ctl_status));
+	printf("boot_override	 = 0x%02x\n", CPLD_READ(boot_override));
+	printf("boot_config1	 = 0x%02x\n", CPLD_READ(boot_config1));
+	printf("boot_config2	 = 0x%02x\n", CPLD_READ(boot_config2));
+	putc('\n');
+}
+#endif
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int rc = 0;
+
+	if (argc <= 1)
+		return cmd_usage(cmdtp);
+
+	if (strcmp(argv[1], "reset") == 0) {
+		if (strcmp(argv[2], "altbank") == 0)
+			cpld_set_altbank();
+		else
+			cpld_set_defbank();
+#ifdef DEBUG
+	} else if (strcmp(argv[1], "dump") == 0) {
+		cpld_dump_regs();
+#endif
+	} else
+		rc = cmd_usage(cmdtp);
+
+	return rc;
+}
+
+U_BOOT_CMD(
+	cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+	"Reset the board or alternate bank",
+	"reset - hard reset to default bank\n"
+	"cpld reset altbank - reset to alternate bank\n"
+#ifdef DEBUG
+	"cpld dump - display the CPLD registers\n"
+#endif
+	);
diff --git a/board/freescale/t104xrdb/cpld.h b/board/freescale/t104xrdb/cpld.h
new file mode 100644
index 00000000000..0da9a0159ba
--- /dev/null
+++ b/board/freescale/t104xrdb/cpld.h
@@ -0,0 +1,40 @@
+/**
+ * Copyright 2013 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * This file provides support for the ngPIXIS, a board-specific FPGA used on
+ * some Freescale reference boards.
+ */
+
+/*
+ * CPLD register set. Feel free to add board-specific #ifdefs where necessary.
+ */
+struct cpld_data {
+	u8 cpld_ver;		/* 0x00 - CPLD Major Revision Register */
+	u8 cpld_ver_sub;	/* 0x01 - CPLD Minor Revision Register */
+	u8 hw_ver;		/* 0x02 - Hardware Revision Register */
+	u8 sw_ver;		/* 0x03 - Software Revision register */
+	u8 res0[12];		/* 0x04 - 0x0F - not used */
+	u8 reset_ctl1;		/* 0x10 - Reset control Register1 */
+	u8 reset_ctl2;		/* 0x11 - Reset control Register2 */
+	u8 int_status;		/* 0x12 - Interrupt status Register */
+	u8 flash_ctl_status;	/* 0x13 - Flash control and status register */
+	u8 fan_ctl_status;	/* 0x14 - Fan control and status register  */
+	u8 led_ctl_status;	/* 0x15 - LED control and status register */
+	u8 sfp_ctl_status;	/* 0x16 - SFP control and status register  */
+	u8 misc_ctl_status;	/* 0x17 - Miscellanies ctrl & status register*/
+	u8 boot_override;	/* 0x18 - Boot override register */
+	u8 boot_config1;	/* 0x19 - Boot config override register*/
+	u8 boot_config2;	/* 0x1A - Boot config override register*/
+} cpld_data_t;
+
+
+/* Pointer to the CPLD register set */
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value)\
+		cpld_write(offsetof(struct cpld_data, reg), value)
diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c
index 57d0f9cfd86..34c9224adb6 100644
--- a/board/freescale/t104xrdb/ddr.c
+++ b/board/freescale/t104xrdb/ddr.c
@@ -113,6 +113,7 @@ phys_size_t initdram(int board_type)
 {
 	phys_size_t dram_size;
 
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 	puts("Initializing....using SPD\n");
 
 	dram_size = fsl_ddr_sdram();
@@ -120,6 +121,8 @@ phys_size_t initdram(int board_type)
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
 
-	puts("    DDR: ");
+#else
+	dram_size =  fsl_ddr_sdram_size();
+#endif
 	return dram_size;
 }
diff --git a/board/freescale/t104xrdb/eth.c b/board/freescale/t104xrdb/eth.c
index 0188fd4090b..63e5f900da7 100644
--- a/board/freescale/t104xrdb/eth.c
+++ b/board/freescale/t104xrdb/eth.c
@@ -41,6 +41,7 @@ int board_eth_init(bd_t *bis)
 			/* T1040RDB only supports SGMII on DTSEC3 */
 			fm_info_set_phy_address(FM1_DTSEC3,
 						CONFIG_SYS_SGMII1_PHY_ADDR);
+			break;
 #endif
 		case PHY_INTERFACE_MODE_RGMII:
 			if (FM1_DTSEC4 == i)
diff --git a/board/freescale/t104xrdb/spl.c b/board/freescale/t104xrdb/spl.c
new file mode 100644
index 00000000000..c628c95f2d2
--- /dev/null
+++ b/board/freescale/t104xrdb/spl.c
@@ -0,0 +1,122 @@
+/* Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	return CONFIG_DDR_CLK_FREQ;
+}
+
+#define FSL_CORENET_CCSR_PORSR1_RCW_MASK	0xFF800000
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, uart_clk;
+#ifdef CONFIG_SPL_NAND_BOOT
+	u32 porsr1, pinctl;
+#endif
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	/*
+	 * There is T1040 SoC issue where NOR, FPGA are inaccessible during
+	 * NAND boot because IFC signals > IFC_AD7 are not enabled.
+	 * This workaround changes RCW source to make all signals enabled.
+	 */
+	porsr1 = in_be32(&gur->porsr1);
+	pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
+	out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#endif
+
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	/* compiler optimization barrier needed for GCC >= 3.4 */
+	__asm__ __volatile__("" : : : "memory");
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	uart_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     uart_clk / 16 / CONFIG_BAUDRATE);
+
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+#endif
+
+	/* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	i2c_init_all();
+
+	puts("\n\n");
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/t104xrdb/t1040_rcw.cfg b/board/freescale/t104xrdb/t1040_rcw.cfg
new file mode 100644
index 00000000000..3300c184a1a
--- /dev/null
+++ b/board/freescale/t104xrdb/t1040_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x66
+0c18000e 0e000000 00000000 00000000
+66000002 80000002 e8106000 01000000
+00000000 00000000 00000000 00032810
+00000000 0342500f 00000000 00000000
diff --git a/board/freescale/t104xrdb/t1042_rcw.cfg b/board/freescale/t104xrdb/t1042_rcw.cfg
new file mode 100644
index 00000000000..a3ea8ada56c
--- /dev/null
+++ b/board/freescale/t104xrdb/t1042_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x66
+0c18000e 0e000000 00000000 00000000
+06000002 00400002 e8106000 01000000
+00000000 00000000 00000000 00030810
+00000000 01fe0a06 00000000 00000000
diff --git a/board/freescale/t104xrdb/t104x_pbi.cfg b/board/freescale/t104xrdb/t104x_pbi.cfg
new file mode 100644
index 00000000000..7b9e9b05f70
--- /dev/null
+++ b/board/freescale/t104xrdb/t104x_pbi.cfg
@@ -0,0 +1,26 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 256KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cd0 00000000
+09000cd4 fffc0000
+09000cd8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+091380c0 000FFFFF
diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c
index 6e29d641077..fb5b84940ea 100644
--- a/board/freescale/t104xrdb/t104xrdb.c
+++ b/board/freescale/t104xrdb/t104xrdb.c
@@ -17,16 +17,30 @@
 #include <asm/fsl_portals.h>
 #include <asm/fsl_liodn.h>
 #include <fm_eth.h>
+#include <asm/mpc85xx_gpio.h>
 
 #include "t104xrdb.h"
+#include "cpld.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
 int checkboard(void)
 {
 	struct cpu_type *cpu = gd->arch.cpu;
+	u8 sw;
 
 	printf("Board: %sRDB\n", cpu->name);
+	printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
+	       CPLD_READ(hw_ver), CPLD_READ(sw_ver));
+
+	sw = CPLD_READ(flash_ctl_status);
+	sw = ((sw & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
+
+	if (sw <= 7)
+		printf("vBank: %d\n", sw);
+	else
+		printf("Unsupported Bank=%x\n", sw);
+
 	return 0;
 }
 
@@ -91,3 +105,12 @@ void ft_board_setup(void *blob, bd_t *bd)
 	fdt_fixup_fman_ethernet(blob);
 #endif
 }
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+	/* Disable MCKE isolation */
+	gpio_set_value(2, 0);
+	udelay(1);
+}
+#endif
diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c
index 84f97a41e36..95c15aa5965 100644
--- a/board/freescale/t104xrdb/tlb.c
+++ b/board/freescale/t104xrdb/tlb.c
@@ -53,6 +53,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
 		      0, 2, BOOKE_PAGESZ_256M, 1),
 
+#ifndef CONFIG_SPL_BUILD
 	/* *I*G* - PCI */
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -82,6 +83,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 8, BOOKE_PAGESZ_16M, 1),
 #endif
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -102,6 +104,16 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 11, BOOKE_PAGESZ_256K, 1),
 #endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 12, BOOKE_PAGESZ_1G, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
 };
 
 int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/t208xqds/Makefile b/board/freescale/t208xqds/Makefile
index 947b7f73241..6cb72c9fd5d 100644
--- a/board/freescale/t208xqds/Makefile
+++ b/board/freescale/t208xqds/Makefile
@@ -4,11 +4,16 @@
 # SPDX-License-Identifier:      GPL-2.0+
 #
 
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-$(CONFIG_T2080QDS) += t208xqds.o
 obj-$(CONFIG_T2080QDS) += eth_t208xqds.o
 obj-$(CONFIG_T2081QDS) += t208xqds.o
 obj-$(CONFIG_T2081QDS) += eth_t208xqds.o
 obj-$(CONFIG_PCI)      += pci.o
+endif
+
 obj-y   += ddr.o
 obj-y   += law.o
 obj-y   += tlb.o
diff --git a/board/freescale/t208xqds/ddr.c b/board/freescale/t208xqds/ddr.c
index ed1334d9859..3348971b01e 100644
--- a/board/freescale/t208xqds/ddr.c
+++ b/board/freescale/t208xqds/ddr.c
@@ -107,13 +107,16 @@ phys_size_t initdram(int board_type)
 {
 	phys_size_t dram_size;
 
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 	puts("Initializing....using SPD\n");
-
 	dram_size = fsl_ddr_sdram();
 
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
+#else
+	/* DDR has been initialised by first stage boot loader */
+	dram_size =  fsl_ddr_sdram_size();
+#endif
 
-	puts("    DDR: ");
 	return dram_size;
 }
diff --git a/board/freescale/t208xqds/spl.c b/board/freescale/t208xqds/spl.c
new file mode 100644
index 00000000000..a71c6171218
--- /dev/null
+++ b/board/freescale/t208xqds/spl.c
@@ -0,0 +1,137 @@
+/* Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+#include "../common/qixis.h"
+#include "t208xqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0F) {
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, ccb_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	ccb_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	puts("\nNAND boot...\n");
+#endif
+
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	i2c_init_all();
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/t208xqds/tlb.c b/board/freescale/t208xqds/tlb.c
index 62cd11033ad..8d602989b2d 100644
--- a/board/freescale/t208xqds/tlb.c
+++ b/board/freescale/t208xqds/tlb.c
@@ -65,6 +65,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
 		      0, 2, BOOKE_PAGESZ_256M, 1),
 
+#ifndef CONFIG_SPL_BUILD
 	/* *I*G* - PCIe 1, 0x80000000 */
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -110,6 +111,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 12, BOOKE_PAGESZ_16M, 1),
 #endif
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -141,6 +143,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      0, 18, BOOKE_PAGESZ_1M, 1),
 #endif
 
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 19, BOOKE_PAGESZ_2G, 1)
+#endif
 };
 
 int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/t208xrdb/Makefile b/board/freescale/t208xrdb/Makefile
index 092c9ff0dce..9605f8b606c 100644
--- a/board/freescale/t208xrdb/Makefile
+++ b/board/freescale/t208xrdb/Makefile
@@ -4,10 +4,15 @@
 # SPDX-License-Identifier:      GPL-2.0+
 #
 
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-$(CONFIG_T2080RDB) += t208xrdb.o
 obj-$(CONFIG_T2080RDB) += eth_t208xrdb.o
 obj-$(CONFIG_T2080RDB) += cpld.o
 obj-$(CONFIG_PCI)      += pci.o
+endif
+
 obj-y   += ddr.o
 obj-y   += law.o
 obj-y   += tlb.o
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
index 0012c6cb408..24484cd0ffc 100644
--- a/board/freescale/t208xrdb/README
+++ b/board/freescale/t208xrdb/README
@@ -67,7 +67,7 @@ T2080PCIe-RDB board Overview
      - One PCIe x2 end-point device (C293 Crypto co-processor)
  - IFC/Local Bus
      - NOR:  128MB 16-bit NOR Flash
-     - NAND: 512MB 8-bit NAND flash
+     - NAND: 1GB 8-bit NAND flash
      - CPLD: for system controlling with programable header on-board
  - SATA
      - Two SATA 2.0 onnectors on-board
@@ -120,7 +120,7 @@ Start Address   End Address	Definition			Max size
 0xEBF00000	0xEBF1FFFF	FMAN ucode (alt bank)		128KB
 0xEBE00000	0xEBE3FFFF	PHY CS4315 firmware (alt bank)	256KB
 0xE9300000	0xEBEFFFFF	rootfs (current bank)		44MB
-0xE8800000	0xE88FFFFF	Hardware device tree (cur bank)	11MB + 512KB
+0xE8800000	0xE88FFFFF	Hardware device tree (cur bank)	1MB
 0xE8020000	0xE86FFFFF	Linux.uImage (current bank)	7MB + 875KB
 0xE8000000	0xE801FFFF	RCW (current bank)		128KB
 
@@ -146,7 +146,8 @@ Software configurations and board settings
 ------------------------------------------
 1. NOR boot:
    a. build NOR boot image
-	$ make T2080RDB
+	$ make T2080RDB_config
+	$ make
    b. program u-boot.bin image to NOR flash
 	=> tftp 1000000 u-boot.bin
 	=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
@@ -155,18 +156,18 @@ Software configurations and board settings
    Switching between default bank and alternate bank on NOR flash
    To change boot source to vbank4:
 	via software:   run command 'cpld reset altbank' in u-boot.
-	via DIP-switch: set SW3[5:7] = '011'
+	via DIP-switch: set SW3[5:7] = '100'
 
    To change boot source to vbank0:
 	via software:   run command 'cpld reset' in u-boot.
-	via DIP-Switch: set SW3[5:7] = '111'
+	via DIP-Switch: set SW3[5:7] = '000'
 
 2. NAND Boot:
    a. build PBL image for NAND boot
 	$ make T2080RDB_NAND_config
-	$ make u-boot.pbl
-   b. program u-boot.pbl to NAND flash
-	=> tftp 1000000 u-boot.pbl
+	$ make
+   b. program u-boot-with-spl-pbl.bin to NAND flash
+	=> tftp 1000000 u-boot-with-spl-pbl.bin
 	=> nand erase 0 d0000
 	=> nand write 1000000 0 $filesize
 	set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
@@ -174,9 +175,9 @@ Software configurations and board settings
 3. SPI Boot:
    a. build PBL image for SPI boot
 	$ make T2080RDB_SPIFLASH_config
-	$ make u-boot.pbl
-   b. program u-boot.pbl to SPI flash
-	=> tftp 1000000 u-boot.pbl
+	$ make
+   b. program u-boot-with-spl-pbl.bin to SPI flash
+	=> tftp 1000000 u-boot-with-spl-pbl.bin
 	=> sf probe 0
 	=> sf erase 0 d0000
 	=> sf write 1000000 0 $filesize
@@ -185,13 +186,68 @@ Software configurations and board settings
 4. SD Boot:
    a. build PBL image for SD boot
 	$ make T2080RDB_SDCARD_config
-	$ make u-boot.pbl
-   b. program u-boot.pbl to TF card
-	=> tftp 1000000 u-boot.pbl
-	=> mmc write 1000000 8 1650
+	$ make
+   b. program u-boot-with-spl-pbl.bin to micro-SD/TF card
+	=> tftp 1000000 u-boot-with-spl-pbl.bin
+	=> mmc write 1000000 8 0x800
 	set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
 
 
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
+SPL further initializes DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area		   | Address			|
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB)		|
+-------------------------------------------------
+|GD, BD		   | 0xFFFC8000 (4KB)		|
+-------------------------------------------------
+|ENV		   | 0xFFFC9000 (8KB)		|
+-------------------------------------------------
+|HEAP		   | 0xFFFCB000 (50KB)		|
+-------------------------------------------------
+|STACK		   | 0xFFFD8000 (22KB)		|
+-------------------------------------------------
+|U-boot SPL	   | 0xFFFD8000 (160KB)		|
+-------------------------------------------------
+
+NAND Flash memory Map on T2080RDB
+--------------------------------------------------------------
+Start		End		Definition	Size
+0x000000	0x0FFFFF	u-boot img	1MB  (2 blocks)
+0x100000	0x17FFFF	u-boot env	512KB (1 block)
+0x180000	0x1FFFFF	FMAN ucode	512KB (1 block)
+0x200000	0x27FFFF	CS4315 ucode	512KB (1 block)
+
+
+Micro SD Card memory Map on T2080RDB
+----------------------------------------------------
+Block		#blocks		Definition	Size
+0x008		2048		u-boot img	1MB
+0x800		0016		u-boot env	8KB
+0x820		0128		FMAN ucode	64KB
+0x8a0		0512		CS4315 ucode	256KB
+
+
+SPI Flash memory Map on T2080RDB
+----------------------------------------------------
+Start		End		Definition	Size
+0x000000	0x0FFFFF	u-boot img	1MB
+0x100000	0x101FFF	u-boot env	8KB
+0x110000	0x11FFFF	FMAN ucode	64KB
+0x120000        0x15FFFF        CS4315 ucode	256KB
+
+
 How to update the ucode of Cortina CS4315/CS4340 10G PHY
 --------------------------------------------------------
 => tftp 1000000 CS4315-CS4340-PHY-ucode.txt
diff --git a/board/freescale/t208xrdb/cpld.h b/board/freescale/t208xrdb/cpld.h
index 4cee4e55cfc..3f1533888dd 100644
--- a/board/freescale/t208xrdb/cpld.h
+++ b/board/freescale/t208xrdb/cpld.h
@@ -35,8 +35,8 @@ void cpld_write(unsigned int reg, u8 value);
 #define CPLD_LBMAP_MASK		0x3F
 #define CPLD_BANK_SEL_MASK	0x07
 #define CPLD_BANK_OVERRIDE	0x40
-#define CPLD_LBMAP_ALTBANK	0x43 /* BANK OR | BANK 4 */
-#define CPLD_LBMAP_DFLTBANK	0x47 /* BANK OR | BANK 0 */
+#define CPLD_LBMAP_ALTBANK	0x44 /* BANK OR | BANK 4 */
+#define CPLD_LBMAP_DFLTBANK	0x40 /* BANK OR | BANK 0 */
 #define CPLD_LBMAP_RESET	0xFF
 #define CPLD_LBMAP_SHIFT	0x03
 #define CPLD_BOOT_SEL		0x80
diff --git a/board/freescale/t208xrdb/ddr.c b/board/freescale/t208xrdb/ddr.c
index 01e917398f9..8a262762735 100644
--- a/board/freescale/t208xrdb/ddr.c
+++ b/board/freescale/t208xrdb/ddr.c
@@ -100,13 +100,15 @@ phys_size_t initdram(int board_type)
 {
 	phys_size_t dram_size;
 
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 	puts("Initializing....using SPD\n");
-
 	dram_size = fsl_ddr_sdram();
 
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
-
-	puts("    DDR: ");
+#else
+	/* DDR has been initialised by first stage boot loader */
+	dram_size = fsl_ddr_sdram_size();
+#endif
 	return dram_size;
 }
diff --git a/board/freescale/t208xrdb/spl.c b/board/freescale/t208xrdb/spl.c
new file mode 100644
index 00000000000..9ae2b1e863f
--- /dev/null
+++ b/board/freescale/t208xrdb/spl.c
@@ -0,0 +1,107 @@
+/* Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	return CONFIG_DDR_CLK_FREQ;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, ccb_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	ccb_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	puts("\nNAND boot...\n");
+#endif
+
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	i2c_init_all();
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c
index f3fec2aa6eb..265c1f97ddb 100644
--- a/board/freescale/t208xrdb/t208xrdb.c
+++ b/board/freescale/t208xrdb/t208xrdb.c
@@ -44,7 +44,7 @@ int checkboard(void)
 		puts("NAND\n");
 	} else {
 		reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
-		printf("NOR vBank%d\n", ~reg & 0x7);
+		printf("NOR vBank%d\n", reg);
 	}
 #endif
 
diff --git a/board/freescale/t208xrdb/tlb.c b/board/freescale/t208xrdb/tlb.c
index 085d9f5c6a9..2ebea36a5c2 100644
--- a/board/freescale/t208xrdb/tlb.c
+++ b/board/freescale/t208xrdb/tlb.c
@@ -65,6 +65,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
 		      0, 2, BOOKE_PAGESZ_256M, 1),
 
+#ifndef CONFIG_SPL_BUILD
 	/* *I*G* - PCIe 1, 0x80000000 */
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -110,6 +111,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 12, BOOKE_PAGESZ_16M, 1),
 #endif
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -140,7 +142,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
 		      0, 18, BOOKE_PAGESZ_1M, 1),
 #endif
-#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
 	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
 		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
 		      0, 19, BOOKE_PAGESZ_2G, 1)
diff --git a/board/freescale/t4qds/Makefile b/board/freescale/t4qds/Makefile
index 2b1f7aa3019..4e8e5cb8e9a 100644
--- a/board/freescale/t4qds/Makefile
+++ b/board/freescale/t4qds/Makefile
@@ -4,10 +4,14 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-$(CONFIG_T4240QDS) += t4240qds.o
 obj-$(CONFIG_T4240EMU) += t4240emu.o
-obj-y	+= ddr.o
 obj-$(CONFIG_T4240QDS)+= eth.o
 obj-$(CONFIG_PCI)	+= pci.o
+endif
+obj-y	+= ddr.o
 obj-y	+= law.o
 obj-y	+= tlb.o
diff --git a/board/freescale/t4qds/ddr.c b/board/freescale/t4qds/ddr.c
index 7586cc3c4bd..7abd38def1a 100644
--- a/board/freescale/t4qds/ddr.c
+++ b/board/freescale/t4qds/ddr.c
@@ -117,11 +117,15 @@ phys_size_t initdram(int board_type)
 
 	puts("Initializing....using SPD\n");
 
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 	dram_size = fsl_ddr_sdram();
 
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
 
-	puts("    DDR: ");
+#else
+	/* DDR has been initialised by first stage boot loader */
+	dram_size = fsl_ddr_sdram_size();
+#endif
 	return dram_size;
 }
diff --git a/board/freescale/t4qds/spl.c b/board/freescale/t4qds/spl.c
new file mode 100644
index 00000000000..0c6156e7f09
--- /dev/null
+++ b/board/freescale/t4qds/spl.c
@@ -0,0 +1,141 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/spl.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include "../common/qixis.h"
+#include "t4240qds_qixis.h"
+
+#define FSL_CORENET_CCSR_PORSR1_RCW_MASK	0xFF800000
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0F) {
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, ccb_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#ifdef CONFIG_SPL_NAND_BOOT
+	u32 porsr1, pinctl;
+#endif
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	porsr1 = in_be32(&gur->porsr1);
+	pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
+	out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#endif
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	/* compiler optimization barrier needed for GCC >= 3.4 */
+	__asm__ __volatile__("" : : : "memory");
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	ccb_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	puts("\nNAND boot...\n");
+#endif
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	i2c_init_all();
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/t4qds/t4_pbi.cfg b/board/freescale/t4qds/t4_pbi.cfg
index c598fb5afd8..6126266a96f 100644
--- a/board/freescale/t4qds/t4_pbi.cfg
+++ b/board/freescale/t4qds/t4_pbi.cfg
@@ -13,20 +13,6 @@
 09000d00 00000000
 09000d04 fff80000
 09000d08 81000012
-#workaround for IFC bus speed
-091241c0 f03f3f3f
-091241c4 ff003f3f
-09124010 00000101
-09124130 0000000c
-#workaround for SERDES A-006031
-090ea000 064740e6
-090ea020 064740e6
-090eb000 064740e6
-090eb020 064740e6
-090ec000 064740e6
-090ec020 064740e6
-090ed000 064740e6
-090ed020 064740e6
 #Configure alternate space
 09000010 00000000
 09000014 ff000000
diff --git a/board/freescale/t4qds/t4_rcw.cfg b/board/freescale/t4qds/t4_rcw.cfg
index 74df01a70c2..3e568172046 100644
--- a/board/freescale/t4qds/t4_rcw.cfg
+++ b/board/freescale/t4qds/t4_rcw.cfg
@@ -1,7 +1,7 @@
 #PBL preamble and RCW header
 aa55aa55 010e0100
 #serdes protocol  1_28_6_12
-120c0019 0c101915 00000000 00000000
-04383063 30548c00 6c020000 1d000000
+16070019 18101916 00000000 00000000
+04383060 30548c00 ec020000 f5000000
 00000000 ee0000ee 00000000 000307fc
-00000000 00000000 00000000 00000020
+00000000 00000000 00000000 00000028
diff --git a/board/freescale/t4qds/tlb.c b/board/freescale/t4qds/tlb.c
index b701e752093..1e4d096f5f9 100644
--- a/board/freescale/t4qds/tlb.c
+++ b/board/freescale/t4qds/tlb.c
@@ -64,7 +64,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
 		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
 		      0, 2, BOOKE_PAGESZ_256M, 1),
-
+#ifndef CONFIG_SPL_BUILD
 	/* *I*G* - PCI */
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -105,6 +105,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 12, BOOKE_PAGESZ_16M, 1),
 #endif
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -136,6 +137,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      0, 18, BOOKE_PAGESZ_1M, 1),
 #endif
 
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 19, BOOKE_PAGESZ_2G, 1)
+#endif
 };
 
 int num_tlb_entries = ARRAY_SIZE(tlb_table);