mtd: spi_dataflash: Use spi read then write

Now, we have spi_write_then_read routine that would handle
spi_xfer handling based on the tx_buf and rx_buf parameters.

So, replace individual flash read/write/cmd transfer call
with spi_write_then_read.

Cc: Egnite GmbH <info@egnite.de>
Cc: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Cc: Ilko Iliev <iliev@ronetix.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Alison Wang <alison.wang@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

1 files changed, 13 insertions, 9 deletions

diff --git a/drivers/mtd/spi/sf_dataflash.c b/drivers/mtd/spi/sf_dataflash.c
index b6a2631747a..55fb4bd31ac 100644
--- a/drivers/mtd/spi/sf_dataflash.c
+++ b/drivers/mtd/spi/sf_dataflash.c
@@ -76,12 +76,14 @@ struct dataflash {
 static inline int dataflash_status(struct spi_slave *spi)
 {
 	int ret;
+	u8 opcode = OP_READ_STATUS;
 	u8 status;
+
 	/*
 	 * NOTE:  at45db321c over 25 MHz wants to write
 	 * a dummy byte after the opcode...
 	 */
-	ret = spi_flash_cmd(spi, OP_READ_STATUS, &status, 1);
+	ret =  spi_write_then_read(spi, &opcode, 1, NULL, &status, 1);
 	return ret ? -EIO : status;
 }
 
@@ -173,7 +175,7 @@ static int spi_dataflash_erase(struct udevice *dev, u32 offset, size_t len)
 		      command[0], command[1], command[2], command[3],
 		      pageaddr);
 
-		status = spi_flash_cmd_write(spi, command, 4, NULL, 0);
+		status = spi_write_then_read(spi, command, 4, NULL, NULL, 0);
 		if (status < 0) {
 			debug("%s: erase send command error!\n", dev->name);
 			return -EIO;
@@ -248,7 +250,7 @@ static int spi_dataflash_read(struct udevice *dev, u32 offset, size_t len,
 	command[3] = (uint8_t)(addr >> 0);
 
 	/* plus 4 "don't care" bytes, command len: 4 + 4 "don't care" bytes */
-	status = spi_flash_cmd_read(spi, command, 8, buf, len);
+	status = spi_write_then_read(spi, command, 8, NULL, buf, len);
 
 	spi_release_bus(spi);
 
@@ -327,7 +329,8 @@ int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len,
 			debug("TRANSFER: (%x) %x %x %x\n",
 			      command[0], command[1], command[2], command[3]);
 
-			status = spi_flash_cmd_write(spi, command, 4, NULL, 0);
+			status = spi_write_then_read(spi, command, 4,
+						     NULL, NULL, 0);
 			if (status < 0) {
 				debug("%s: write(<pagesize) command error!\n",
 				      dev->name);
@@ -352,8 +355,8 @@ int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len,
 		debug("PROGRAM: (%x) %x %x %x\n",
 		      command[0], command[1], command[2], command[3]);
 
-		status = spi_flash_cmd_write(spi, command,
-					     4, writebuf, writelen);
+		status = spi_write_then_read(spi, command, 4,
+					     writebuf, NULL, writelen);
 		if (status < 0) {
 			debug("%s: write send command error!\n", dev->name);
 			return -EIO;
@@ -376,8 +379,8 @@ int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len,
 		debug("COMPARE: (%x) %x %x %x\n",
 		      command[0], command[1], command[2], command[3]);
 
-		status = spi_flash_cmd_write(spi, command,
-					     4, writebuf, writelen);
+		status = spi_write_then_read(spi, command, 4,
+					     writebuf, NULL, writelen);
 		if (status < 0) {
 			debug("%s: write(compare) send command error!\n",
 			      dev->name);
@@ -508,6 +511,7 @@ static struct data_flash_info *jedec_probe(struct spi_slave *spi)
 	uint8_t			id[5];
 	uint32_t		jedec;
 	struct data_flash_info	*info;
+	u8 opcode		= CMD_READ_ID;
 	int status;
 
 	/*
@@ -519,7 +523,7 @@ static struct data_flash_info *jedec_probe(struct spi_slave *spi)
 	 * That's not an error; only rev C and newer chips handle it, and
 	 * only Atmel sells these chips.
 	 */
-	tmp = spi_flash_cmd(spi, CMD_READ_ID, id, sizeof(id));
+	tmp = spi_write_then_read(spi, &opcode, 1, NULL, id, sizeof(id));
 	if (tmp < 0) {
 		printf("dataflash: error %d reading JEDEC ID\n", tmp);
 		return ERR_PTR(tmp);