diff options
27 files changed, 1048 insertions, 751 deletions
diff --git a/arch/arm/cpu/arm920t/s3c24x0/speed.c b/arch/arm/cpu/arm920t/s3c24x0/speed.c index b13283a798e..3ae558dd628 100644 --- a/arch/arm/cpu/arm920t/s3c24x0/speed.c +++ b/arch/arm/cpu/arm920t/s3c24x0/speed.c @@ -54,9 +54,9 @@ static ulong get_PLLCLK(int pllreg) ulong r, m, p, s; if (pllreg == MPLL) - r = readl(&clk_power->MPLLCON); + r = readl(&clk_power->mpllcon); else if (pllreg == UPLL) - r = readl(&clk_power->UPLLCON); + r = readl(&clk_power->upllcon); else hang(); @@ -64,7 +64,12 @@ static ulong get_PLLCLK(int pllreg) p = ((r & 0x003F0) >> 4) + 2; s = r & 0x3; +#if defined(CONFIG_S3C2440) + if (pllreg == MPLL) + return 2 * m * (CONFIG_SYS_CLK_FREQ / (p << s)); +#endif return (CONFIG_SYS_CLK_FREQ * m) / (p << s); + } /* return FCLK frequency */ @@ -77,8 +82,23 @@ ulong get_FCLK(void) ulong get_HCLK(void) { struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power(); - - return (readl(&clk_power->CLKDIVN) & 2) ? get_FCLK() / 2 : get_FCLK(); +#ifdef CONFIG_S3C2440 + switch (readl(&clk_power->clkdivn) & 0x6) { + default: + case 0: + return get_FCLK(); + case 2: + return get_FCLK() / 2; + case 4: + return (readl(&clk_power->camdivn) & (1 << 9)) ? + get_FCLK() / 8 : get_FCLK() / 4; + case 6: + return (readl(&clk_power->camdivn) & (1 << 8)) ? + get_FCLK() / 6 : get_FCLK() / 3; + } +#else + return (readl(&clk_power->clkdivn) & 2) ? get_FCLK() / 2 : get_FCLK(); +#endif } /* return PCLK frequency */ @@ -86,7 +106,7 @@ ulong get_PCLK(void) { struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power(); - return (readl(&clk_power->CLKDIVN) & 1) ? get_HCLK() / 2 : get_HCLK(); + return (readl(&clk_power->clkdivn) & 1) ? get_HCLK() / 2 : get_HCLK(); } /* return UCLK frequency */ diff --git a/arch/arm/cpu/arm920t/s3c24x0/timer.c b/arch/arm/cpu/arm920t/s3c24x0/timer.c index 7d47354381c..8cf9ff6be00 100644 --- a/arch/arm/cpu/arm920t/s3c24x0/timer.c +++ b/arch/arm/cpu/arm920t/s3c24x0/timer.c @@ -43,7 +43,7 @@ static inline ulong READ_TIMER(void) { struct s3c24x0_timers *timers = s3c24x0_get_base_timers(); - return readl(&timers->TCNTO4) & 0xffff; + return readl(&timers->tcnto4) & 0xffff; } static ulong timestamp; @@ -56,7 +56,7 @@ int timer_init(void) /* use PWM Timer 4 because it has no output */ /* prescaler for Timer 4 is 16 */ - writel(0x0f00, &timers->TCFG0); + writel(0x0f00, &timers->tcfg0); if (timer_load_val == 0) { /* * for 10 ms clock period @ PCLK with 4 bit divider = 1/2 @@ -68,13 +68,13 @@ int timer_init(void) } /* load value for 10 ms timeout */ lastdec = timer_load_val; - writel(timer_load_val, &timers->TCNTB4); - /* auto load, manual update of Timer 4 */ - tmr = (readl(&timers->TCON) & ~0x0700000) | 0x0600000; - writel(tmr, &timers->TCON); - /* auto load, start Timer 4 */ + writel(timer_load_val, &timers->tcntb4); + /* auto load, manual update of timer 4 */ + tmr = (readl(&timers->tcon) & ~0x0700000) | 0x0600000; + writel(tmr, &timers->tcon); + /* auto load, start timer 4 */ tmr = (tmr & ~0x0700000) | 0x0500000; - writel(tmr, &timers->TCON); + writel(tmr, &timers->tcon); timestamp = 0; return (0); @@ -181,6 +181,7 @@ ulong get_tbclk(void) tbclk = timer_load_val * 100; #elif defined(CONFIG_SBC2410X) || \ defined(CONFIG_SMDK2410) || \ + defined(CONFIG_S3C2440) || \ defined(CONFIG_VCMA9) tbclk = CONFIG_SYS_HZ; #else @@ -206,13 +207,13 @@ void reset_cpu(ulong ignored) watchdog = s3c24x0_get_base_watchdog(); /* Disable watchdog */ - writel(0x0000, &watchdog->WTCON); + writel(0x0000, &watchdog->wtcon); /* Initialize watchdog timer count register */ - writel(0x0001, &watchdog->WTCNT); + writel(0x0001, &watchdog->wtcnt); /* Enable watchdog timer; assert reset at timer timeout */ - writel(0x0021, &watchdog->WTCON); + writel(0x0021, &watchdog->wtcon); while (1) /* loop forever and wait for reset to happen */; diff --git a/arch/arm/cpu/arm920t/s3c24x0/usb.c b/arch/arm/cpu/arm920t/s3c24x0/usb.c index e468ed08fc4..226a3f6c90c 100644 --- a/arch/arm/cpu/arm920t/s3c24x0/usb.c +++ b/arch/arm/cpu/arm920t/s3c24x0/usb.c @@ -39,14 +39,14 @@ int usb_cpu_init(void) * Set the 48 MHz UPLL clocking. Values are taken from * "PLL value selection guide", 6-23, s3c2400_UM.pdf. */ - writel((40 << 12) + (1 << 4) + 2, &clk_power->UPLLCON); + writel((40 << 12) + (1 << 4) + 2, &clk_power->upllcon); /* 1 = use pads related USB for USB host */ - writel(readl(&gpio->MISCCR) | 0x8, &gpio->MISCCR); + writel(readl(&gpio->misccr) | 0x8, &gpio->misccr); /* * Enable USB host clock. */ - writel(readl(&clk_power->CLKCON) | (1 << 4), &clk_power->CLKCON); + writel(readl(&clk_power->clkcon) | (1 << 4), &clk_power->clkcon); return 0; } @@ -55,14 +55,14 @@ int usb_cpu_stop(void) { struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power(); /* may not want to do this */ - writel(readl(&clk_power->CLKCON) & ~(1 << 4), &clk_power->CLKCON); + writel(readl(&clk_power->clkcon) & ~(1 << 4), &clk_power->clkcon); return 0; } int usb_cpu_init_fail(void) { struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power(); - writel(readl(&clk_power->CLKCON) & ~(1 << 4), &clk_power->CLKCON); + writel(readl(&clk_power->clkcon) & ~(1 << 4), &clk_power->clkcon); return 0; } diff --git a/arch/arm/cpu/arm920t/s3c24x0/usb_ohci.c b/arch/arm/cpu/arm920t/s3c24x0/usb_ohci.c index 5aa8d64a55c..ccc97384f33 100644 --- a/arch/arm/cpu/arm920t/s3c24x0/usb_ohci.c +++ b/arch/arm/cpu/arm920t/s3c24x0/usb_ohci.c @@ -1666,13 +1666,13 @@ int usb_lowlevel_init(void) * Set the 48 MHz UPLL clocking. Values are taken from * "PLL value selection guide", 6-23, s3c2400_UM.pdf. */ - clk_power->UPLLCON = ((40 << 12) + (1 << 4) + 2); - gpio->MISCCR |= 0x8; /* 1 = use pads related USB for USB host */ + clk_power->upllcon = ((40 << 12) + (1 << 4) + 2); + gpio->misccr |= 0x8; /* 1 = use pads related USB for USB host */ /* * Enable USB host clock. */ - clk_power->CLKCON |= (1 << 4); + clk_power->clkcon |= (1 << 4); memset(&gohci, 0, sizeof(struct ohci)); memset(&urb_priv, 0, sizeof(struct urb_priv)); @@ -1709,7 +1709,7 @@ int usb_lowlevel_init(void) if (hc_reset(&gohci) < 0) { hc_release_ohci(&gohci); /* Initialization failed */ - clk_power->CLKCON &= ~(1 << 4); + clk_power->clkcon &= ~(1 << 4); return -1; } @@ -1722,7 +1722,7 @@ int usb_lowlevel_init(void) err("can't start usb-%s", gohci.slot_name); hc_release_ohci(&gohci); /* Initialization failed */ - clk_power->CLKCON &= ~(1 << 4); + clk_power->clkcon &= ~(1 << 4); return -1; } #ifdef DEBUG @@ -1748,7 +1748,7 @@ int usb_lowlevel_stop(void) /* call hc_release_ohci() here ? */ hc_reset(&gohci); /* may not want to do this */ - clk_power->CLKCON &= ~(1 << 4); + clk_power->clkcon &= ~(1 << 4); return 0; } diff --git a/arch/arm/include/asm/arch-s3c24x0/s3c2440.h b/arch/arm/include/asm/arch-s3c24x0/s3c2440.h new file mode 100644 index 00000000000..8c606e3995a --- /dev/null +++ b/arch/arm/include/asm/arch-s3c24x0/s3c2440.h @@ -0,0 +1,161 @@ +/* + * (C) Copyright 2003 + * David Mueller ELSOFT AG Switzerland. d.mueller@elsoft.ch + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************ + * NAME : s3c2440.h + * Version : 31.3.2003 + * + * Based on S3C2440 User's manual Rev x.x + ************************************************/ + +#ifndef __S3C2440_H__ +#define __S3C2440_H__ + +#define S3C24X0_UART_CHANNELS 3 +#define S3C24X0_SPI_CHANNELS 2 + +/* S3C2440 only supports 512 Byte HW ECC */ +#define S3C2440_ECCSIZE 512 +#define S3C2440_ECCBYTES 3 + +enum s3c24x0_uarts_nr { + S3C24X0_UART0, + S3C24X0_UART1, + S3C24X0_UART2 +}; + +/* S3C2440 device base addresses */ +#define S3C24X0_MEMCTL_BASE 0x48000000 +#define S3C24X0_USB_HOST_BASE 0x49000000 +#define S3C24X0_INTERRUPT_BASE 0x4A000000 +#define S3C24X0_DMA_BASE 0x4B000000 +#define S3C24X0_CLOCK_POWER_BASE 0x4C000000 +#define S3C24X0_LCD_BASE 0x4D000000 +#define S3C2440_NAND_BASE 0x4E000000 +#define S3C24X0_UART_BASE 0x50000000 +#define S3C24X0_TIMER_BASE 0x51000000 +#define S3C24X0_USB_DEVICE_BASE 0x52000140 +#define S3C24X0_WATCHDOG_BASE 0x53000000 +#define S3C24X0_I2C_BASE 0x54000000 +#define S3C24X0_I2S_BASE 0x55000000 +#define S3C24X0_GPIO_BASE 0x56000000 +#define S3C24X0_RTC_BASE 0x57000000 +#define S3C2440_ADC_BASE 0x58000000 +#define S3C24X0_SPI_BASE 0x59000000 +#define S3C2440_SDI_BASE 0x5A000000 + +/* include common stuff */ +#include <asm/arch/s3c24x0.h> + +static inline struct s3c24x0_memctl *s3c24x0_get_base_memctl(void) +{ + return (struct s3c24x0_memctl *)S3C24X0_MEMCTL_BASE; +} + +static inline struct s3c24x0_usb_host *s3c24x0_get_base_usb_host(void) +{ + return (struct s3c24x0_usb_host *)S3C24X0_USB_HOST_BASE; +} + +static inline struct s3c24x0_interrupt *s3c24x0_get_base_interrupt(void) +{ + return (struct s3c24x0_interrupt *)S3C24X0_INTERRUPT_BASE; +} + +static inline struct s3c24x0_dmas *s3c24x0_get_base_dmas(void) +{ + return (struct s3c24x0_dmas *)S3C24X0_DMA_BASE; +} + +static inline struct s3c24x0_clock_power *s3c24x0_get_base_clock_power(void) +{ + return (struct s3c24x0_clock_power *)S3C24X0_CLOCK_POWER_BASE; +} + +static inline struct s3c24x0_lcd *s3c24x0_get_base_lcd(void) +{ + return (struct s3c24x0_lcd *)S3C24X0_LCD_BASE; +} + +static inline struct s3c2440_nand *s3c2440_get_base_nand(void) +{ + return (struct s3c2440_nand *)S3C2440_NAND_BASE; +} + +static inline struct s3c24x0_uart + *s3c24x0_get_base_uart(enum s3c24x0_uarts_nr n) +{ + return (struct s3c24x0_uart *)(S3C24X0_UART_BASE + (n * 0x4000)); +} + +static inline struct s3c24x0_timers *s3c24x0_get_base_timers(void) +{ + return (struct s3c24x0_timers *)S3C24X0_TIMER_BASE; +} + +static inline struct s3c24x0_usb_device *s3c24x0_get_base_usb_device(void) +{ + return (struct s3c24x0_usb_device *)S3C24X0_USB_DEVICE_BASE; +} + +static inline struct s3c24x0_watchdog *s3c24x0_get_base_watchdog(void) +{ + return (struct s3c24x0_watchdog *)S3C24X0_WATCHDOG_BASE; +} + +static inline struct s3c24x0_i2c *s3c24x0_get_base_i2c(void) +{ + return (struct s3c24x0_i2c *)S3C24X0_I2C_BASE; +} + +static inline struct s3c24x0_i2s *s3c24x0_get_base_i2s(void) +{ + return (struct s3c24x0_i2s *)S3C24X0_I2S_BASE; +} + +static inline struct s3c24x0_gpio *s3c24x0_get_base_gpio(void) +{ + return (struct s3c24x0_gpio *)S3C24X0_GPIO_BASE; +} + +static inline struct s3c24x0_rtc *s3c24x0_get_base_rtc(void) +{ + return (struct s3c24x0_rtc *)S3C24X0_RTC_BASE; +} + +static inline struct s3c2440_adc *s3c2440_get_base_adc(void) +{ + return (struct s3c2440_adc *)S3C2440_ADC_BASE; +} + +static inline struct s3c24x0_spi *s3c24x0_get_base_spi(void) +{ + return (struct s3c24x0_spi *)S3C24X0_SPI_BASE; +} + +static inline struct s3c2440_sdi *s3c2440_get_base_sdi(void) +{ + return (struct s3c2440_sdi *)S3C2440_SDI_BASE; +} + +#endif /*__S3C2440_H__*/ diff --git a/arch/arm/include/asm/arch-s3c24x0/s3c24x0.h b/arch/arm/include/asm/arch-s3c24x0/s3c24x0.h index 15f53dd35be..f634d112964 100644 --- a/arch/arm/include/asm/arch-s3c24x0/s3c24x0.h +++ b/arch/arm/include/asm/arch-s3c24x0/s3c24x0.h @@ -33,12 +33,12 @@ /* Memory controller (see manual chapter 5) */ struct s3c24x0_memctl { - u32 BWSCON; - u32 BANKCON[8]; - u32 REFRESH; - u32 BANKSIZE; - u32 MRSRB6; - u32 MRSRB7; + u32 bwscon; + u32 bankcon[8]; + u32 refresh; + u32 banksize; + u32 mrsrb6; + u32 mrsrb7; }; @@ -72,40 +72,38 @@ struct s3c24x0_usb_host { /* INTERRUPT (see manual chapter 14) */ struct s3c24x0_interrupt { - u32 SRCPND; - u32 INTMOD; - u32 INTMSK; - u32 PRIORITY; - u32 INTPND; - u32 INTOFFSET; -#ifdef CONFIG_S3C2410 - u32 SUBSRCPND; - u32 INTSUBMSK; + u32 srcpnd; + u32 intmod; + u32 intmsk; + u32 priority; + u32 intpnd; + u32 intoffset; +#if defined(CONFIG_S3C2410) || defined(CONFIG_S3C2440) + u32 subsrcpnd; + u32 intsubmsk; #endif }; /* DMAS (see manual chapter 8) */ struct s3c24x0_dma { - u32 DISRC; -#ifdef CONFIG_S3C2410 - u32 DISRCC; + u32 disrc; +#if defined(CONFIG_S3C2410) || defined(CONFIG_S3C2440) + u32 disrcc; #endif - u32 DIDST; -#ifdef CONFIG_S3C2410 - u32 DIDSTC; + u32 didst; +#if defined(CONFIG_S3C2410) || defined(CONFIG_S3C2440) + u32 didstc; #endif - u32 DCON; - u32 DSTAT; - u32 DCSRC; - u32 DCDST; - u32 DMASKTRIG; -#ifdef CONFIG_S3C2400 + u32 dcon; + u32 dstat; + u32 dcsrc; + u32 dcdst; + u32 dmasktrig; +#if defined(CONFIG_S3C2400) || defined(CONFIG_S3C2410) \ + || defined(CONFIG_S3C2440) u32 res[1]; #endif -#ifdef CONFIG_S3C2410 - u32 res[7]; -#endif }; struct s3c24x0_dmas { @@ -116,90 +114,111 @@ struct s3c24x0_dmas { /* CLOCK & POWER MANAGEMENT (see S3C2400 manual chapter 6) */ /* (see S3C2410 manual chapter 7) */ struct s3c24x0_clock_power { - u32 LOCKTIME; - u32 MPLLCON; - u32 UPLLCON; - u32 CLKCON; - u32 CLKSLOW; - u32 CLKDIVN; + u32 locktime; + u32 mpllcon; + u32 upllcon; + u32 clkcon; + u32 clkslow; + u32 clkdivn; +#if defined(CONFIG_S3C2440) + u32 camdivn; +#endif }; /* LCD CONTROLLER (see manual chapter 15) */ struct s3c24x0_lcd { - u32 LCDCON1; - u32 LCDCON2; - u32 LCDCON3; - u32 LCDCON4; - u32 LCDCON5; - u32 LCDSADDR1; - u32 LCDSADDR2; - u32 LCDSADDR3; - u32 REDLUT; - u32 GREENLUT; - u32 BLUELUT; + u32 lcdcon1; + u32 lcdcon2; + u32 lcdcon3; + u32 lcdcon4; + u32 lcdcon5; + u32 lcdsaddr1; + u32 lcdsaddr2; + u32 lcdsaddr3; + u32 redlut; + u32 greenlut; + u32 bluelut; u32 res[8]; - u32 DITHMODE; - u32 TPAL; -#ifdef CONFIG_S3C2410 - u32 LCDINTPND; - u32 LCDSRCPND; - u32 LCDINTMSK; - u32 LPCSEL; + u32 dithmode; + u32 tpal; +#if defined(CONFIG_S3C2410) || defined(CONFIG_S3C2440) + u32 lcdintpnd; + u32 lcdsrcpnd; + u32 lcdintmsk; + u32 lpcsel; #endif }; +#ifdef CONFIG_S3C2410 /* NAND FLASH (see S3C2410 manual chapter 6) */ struct s3c2410_nand { - u32 NFCONF; - u32 NFCMD; - u32 NFADDR; - u32 NFDATA; - u32 NFSTAT; - u32 NFECC; + u32 nfconf; + u32 nfcmd; + u32 nfaddr; + u32 nfdata; + u32 nfstat; + u32 nfecc; +}; +#endif +#ifdef CONFIG_S3C2440 +/* NAND FLASH (see S3C2440 manual chapter 6) */ +struct s3c2440_nand { + u32 nfconf; + u32 nfcont; + u32 nfcmd; + u32 nfaddr; + u32 nfdata; + u32 nfeccd0; + u32 nfeccd1; + u32 nfeccd; + u32 nfstat; + u32 nfstat0; + u32 nfstat1; }; +#endif /* UART (see manual chapter 11) */ struct s3c24x0_uart { - u32 ULCON; - u32 UCON; - u32 UFCON; - u32 UMCON; - u32 UTRSTAT; - u32 UERSTAT; - u32 UFSTAT; - u32 UMSTAT; + u32 ulcon; + u32 ucon; + u32 ufcon; + u32 umcon; + u32 utrstat; + u32 uerstat; + u32 ufstat; + u32 umstat; #ifdef __BIG_ENDIAN u8 res1[3]; - u8 UTXH; + u8 utxh; u8 res2[3]; - u8 URXH; + u8 urxh; #else /* Little Endian */ - u8 UTXH; + u8 utxh; u8 res1[3]; - u8 URXH; + u8 urxh; u8 res2[3]; #endif - u32 UBRDIV; + u32 ubrdiv; }; /* PWM TIMER (see manual chapter 10) */ struct s3c24x0_timer { - u32 TCNTB; - u32 TCMPB; - u32 TCNTO; + u32 tcntb; + u32 tcmpb; + u32 tcnto; }; struct s3c24x0_timers { - u32 TCFG0; - u32 TCFG1; - u32 TCON; + u32 tcfg0; + u32 tcfg1; + u32 tcon; struct s3c24x0_timer ch[4]; - u32 TCNTB4; - u32 TCNTO4; + u32 tcntb4; + u32 tcnto4; }; @@ -207,9 +226,9 @@ struct s3c24x0_timers { struct s3c24x0_usb_dev_fifos { #ifdef __BIG_ENDIAN u8 res[3]; - u8 EP_FIFO_REG; + u8 ep_fifo_reg; #else /* little endian */ - u8 EP_FIFO_REG; + u8 ep_fifo_reg; u8 res[3]; #endif }; @@ -217,29 +236,29 @@ struct s3c24x0_usb_dev_fifos { struct s3c24x0_usb_dev_dmas { #ifdef __BIG_ENDIAN u8 res1[3]; - u8 EP_DMA_CON; + u8 ep_dma_con; u8 res2[3]; - u8 EP_DMA_UNIT; + u8 ep_dma_unit; u8 res3[3]; - u8 EP_DMA_FIFO; + u8 ep_dma_fifo; u8 res4[3]; - u8 EP_DMA_TTC_L; + u8 ep_dma_ttc_l; u8 res5[3]; - u8 EP_DMA_TTC_M; + u8 ep_dma_ttc_m; u8 res6[3]; - u8 EP_DMA_TTC_H; + u8 ep_dma_ttc_h; #else /* little endian */ - u8 EP_DMA_CON; + u8 ep_dma_con; u8 res1[3]; - u8 EP_DMA_UNIT; + u8 ep_dma_unit; u8 res2[3]; - u8 EP_DMA_FIFO; + u8 ep_dma_fifo; u8 res3[3]; - u8 EP_DMA_TTC_L; + u8 ep_dma_ttc_l; u8 res4[3]; - u8 EP_DMA_TTC_M; + u8 ep_dma_ttc_m; u8 res5[3]; - u8 EP_DMA_TTC_H; + u8 ep_dma_ttc_h; u8 res6[3]; #endif }; @@ -247,69 +266,69 @@ struct s3c24x0_usb_dev_dmas { struct s3c24x0_usb_device { #ifdef __BIG_ENDIAN u8 res1[3]; - u8 FUNC_ADDR_REG; + u8 func_addr_reg; u8 res2[3]; - u8 PWR_REG; + u8 pwr_reg; u8 res3[3]; - u8 EP_INT_REG; + u8 ep_int_reg; u8 res4[15]; - u8 USB_INT_REG; + u8 usb_int_reg; u8 res5[3]; - u8 EP_INT_EN_REG; + u8 ep_int_en_reg; u8 res6[15]; - u8 USB_INT_EN_REG; + u8 usb_int_en_reg; u8 res7[3]; - u8 FRAME_NUM1_REG; + u8 frame_num1_reg; u8 res8[3]; - u8 FRAME_NUM2_REG; + u8 frame_num2_reg; u8 res9[3]; - u8 INDEX_REG; + u8 index_reg; u8 res10[7]; - u8 MAXP_REG; + u8 maxp_reg; u8 res11[3]; - u8 EP0_CSR_IN_CSR1_REG; + u8 ep0_csr_in_csr1_reg; u8 res12[3]; - u8 IN_CSR2_REG; + u8 in_csr2_reg; u8 res13[7]; - u8 OUT_CSR1_REG; + u8 out_csr1_reg; u8 res14[3]; - u8 OUT_CSR2_REG; + u8 out_csr2_reg; u8 res15[3]; - u8 OUT_FIFO_CNT1_REG; + u8 out_fifo_cnt1_reg; u8 res16[3]; - u8 OUT_FIFO_CNT2_REG; + u8 out_fifo_cnt2_reg; #else /* little endian */ - u8 FUNC_ADDR_REG; + u8 func_addr_reg; u8 res1[3]; - u8 PWR_REG; + u8 pwr_reg; u8 res2[3]; - u8 EP_INT_REG; + u8 ep_int_reg; u8 res3[15]; - u8 USB_INT_REG; + u8 usb_int_reg; u8 res4[3]; - u8 EP_INT_EN_REG; + u8 ep_int_en_reg; u8 res5[15]; - u8 USB_INT_EN_REG; + u8 usb_int_en_reg; u8 res6[3]; - u8 FRAME_NUM1_REG; + u8 frame_num1_reg; u8 res7[3]; - u8 FRAME_NUM2_REG; + u8 frame_num2_reg; u8 res8[3]; - u8 INDEX_REG; + u8 index_reg; u8 res9[7]; - u8 MAXP_REG; + u8 maxp_reg; u8 res10[7]; - u8 EP0_CSR_IN_CSR1_REG; + u8 ep0_csr_in_csr1_reg; u8 res11[3]; - u8 IN_CSR2_REG; + u8 in_csr2_reg; u8 res12[3]; - u8 OUT_CSR1_REG; + u8 out_csr1_reg; u8 res13[7]; - u8 OUT_CSR2_REG; + u8 out_csr2_reg; u8 res14[3]; - u8 OUT_FIFO_CNT1_REG; + u8 out_fifo_cnt1_reg; u8 res15[3]; - u8 OUT_FIFO_CNT2_REG; + u8 out_fifo_cnt2_reg; u8 res16[3]; #endif /* __BIG_ENDIAN */ struct s3c24x0_usb_dev_fifos fifo[5]; @@ -319,18 +338,18 @@ struct s3c24x0_usb_device { /* WATCH DOG TIMER (see manual chapter 18) */ struct s3c24x0_watchdog { - u32 WTCON; - u32 WTDAT; - u32 WTCNT; + u32 wtcon; + u32 wtdat; + u32 wtcnt; }; /* IIC (see manual chapter 20) */ struct s3c24x0_i2c { - u32 IICCON; - u32 IICSTAT; - u32 IICADD; - u32 IICDS; + u32 iiccon; + u32 iicstat; + u32 iicadd; + u32 iicds; }; @@ -338,25 +357,25 @@ struct s3c24x0_i2c { struct s3c24x0_i2s { #ifdef __BIG_ENDIAN u16 res1; - u16 IISCON; + u16 iiscon; u16 res2; - u16 IISMOD; + u16 iismod; u16 res3; - u16 IISPSR; + u16 iispsr; u16 res4; - u16 IISFCON; + u16 iisfcon; u16 res5; - u16 IISFIFO; + u16 iisfifo; #else /* little endian */ - u16 IISCON; + u16 iiscon; u16 res1; - u16 IISMOD; + u16 iismod; u16 res2; - u16 IISPSR; + u16 iispsr; u16 res3; - u16 IISFCON; + u16 iisfcon; u16 res4; - u16 IISFIFO; + u16 iisfifo; u16 res5; #endif }; @@ -365,87 +384,146 @@ struct s3c24x0_i2s { /* I/O PORT (see manual chapter 9) */ struct s3c24x0_gpio { #ifdef CONFIG_S3C2400 - u32 PACON; - u32 PADAT; + u32 pacon; + u32 padat; - u32 PBCON; - u32 PBDAT; - u32 PBUP; + u32 pbcon; + u32 pbdat; + u32 pbup; - u32 PCCON; - u32 PCDAT; - u32 PCUP; + u32 pccon; + u32 pcdat; + u32 pcup; - u32 PDCON; - u32 PDDAT; - u32 PDUP; + u32 pdcon; + u32 pddat; + u32 pdup; - u32 PECON; - u32 PEDAT; - u32 PEUP; + u32 pecon; + u32 pedat; + u32 peup; - u32 PFCON; - u32 PFDAT; - u32 PFUP; + u32 pfcon; + u32 pfdat; + u32 pfup; - u32 PGCON; - u32 PGDAT; - u32 PGUP; + u32 pgcon; + u32 pgdat; + u32 pgup; - u32 OPENCR; + u32 opencr; - u32 MISCCR; - u32 EXTINT; + u32 misccr; + u32 extint; #endif #ifdef CONFIG_S3C2410 - u32 GPACON; - u32 GPADAT; + u32 gpacon; + u32 gpadat; + u32 res1[2]; + u32 gpbcon; + u32 gpbdat; + u32 gpbup; + u32 res2; + u32 gpccon; + u32 gpcdat; + u32 gpcup; + u32 res3; + u32 gpdcon; + u32 gpddat; + u32 gpdup; + u32 res4; + u32 gpecon; + u32 gpedat; + u32 gpeup; + u32 res5; + u32 gpfcon; + u32 gpfdat; + u32 gpfup; + u32 res6; + u32 gpgcon; + u32 gpgdat; + u32 gpgup; + u32 res7; + u32 gphcon; + u32 gphdat; + u32 gphup; + u32 res8; + + u32 misccr; + u32 dclkcon; + u32 extint0; + u32 extint1; + u32 extint2; + u32 eintflt0; + u32 eintflt1; + u32 eintflt2; + u32 eintflt3; + u32 eintmask; + u32 eintpend; + u32 gstatus0; + u32 gstatus1; + u32 gstatus2; + u32 gstatus3; + u32 gstatus4; +#endif +#if defined(CONFIG_S3C2440) + u32 gpacon; + u32 gpadat; u32 res1[2]; - u32 GPBCON; - u32 GPBDAT; - u32 GPBUP; + u32 gpbcon; + u32 gpbdat; + u32 gpbup; u32 res2; - u32 GPCCON; - u32 GPCDAT; - u32 GPCUP; + u32 gpccon; + u32 gpcdat; + u32 gpcup; u32 res3; - u32 GPDCON; - u32 GPDDAT; - u32 GPDUP; + u32 gpdcon; + u32 gpddat; + u32 gpdup; u32 res4; - u32 GPECON; - u32 GPEDAT; - u32 GPEUP; + u32 gpecon; + u32 gpedat; + u32 gpeup; u32 res5; - u32 GPFCON; - u32 GPFDAT; - u32 GPFUP; + u32 gpfcon; + u32 gpfdat; + u32 gpfup; u32 res6; - u32 GPGCON; - u32 GPGDAT; - u32 GPGUP; + u32 gpgcon; + u32 gpgdat; + u32 gpgup; u32 res7; - u32 GPHCON; - u32 GPHDAT; - u32 GPHUP; + u32 gphcon; + u32 gphdat; + u32 gphup; u32 res8; - u32 MISCCR; - u32 DCLKCON; - u32 EXTINT0; - u32 EXTINT1; - u32 EXTINT2; - u32 EINTFLT0; - u32 EINTFLT1; - u32 EINTFLT2; - u32 EINTFLT3; - u32 EINTMASK; - u32 EINTPEND; - u32 GSTATUS0; - u32 GSTATUS1; - u32 GSTATUS2; - u32 GSTATUS3; - u32 GSTATUS4; + u32 misccr; + u32 dclkcon; + u32 extint0; + u32 extint1; + u32 extint2; + u32 eintflt0; + u32 eintflt1; + u32 eintflt2; + u32 eintflt3; + u32 eintmask; + u32 eintpend; + u32 gstatus0; + u32 gstatus1; + u32 gstatus2; + u32 gstatus3; + u32 gstatus4; + + u32 res9; + u32 dsc0; + u32 dsc1; + u32 mslcon; + u32 gpjcon; + u32 gpjdat; + u32 gpjup; + u32 res10; #endif }; @@ -454,74 +532,74 @@ struct s3c24x0_gpio { struct s3c24x0_rtc { #ifdef __BIG_ENDIAN u8 res1[67]; - u8 RTCCON; + u8 rtccon; u8 res2[3]; - u8 TICNT; + u8 ticnt; u8 res3[11]; - u8 RTCALM; + u8 rtcalm; u8 res4[3]; - u8 ALMSEC; + u8 almsec; u8 res5[3]; - u8 ALMMIN; + u8 almmin; u8 res6[3]; - u8 ALMHOUR; + u8 almhour; u8 res7[3]; - u8 ALMDATE; + u8 almdate; u8 res8[3]; - u8 ALMMON; + u8 almmon; u8 res9[3]; - u8 ALMYEAR; + u8 almyear; u8 res10[3]; - u8 RTCRST; + u8 rtcrst; u8 res11[3]; - u8 BCDSEC; + u8 bcdsec; u8 res12[3]; - u8 BCDMIN; + u8 bcdmin; u8 res13[3]; - u8 BCDHOUR; + u8 bcdhour; u8 res14[3]; - u8 BCDDATE; + u8 bcddate; u8 res15[3]; - u8 BCDDAY; + u8 bcdday; u8 res16[3]; - u8 BCDMON; + u8 bcdmon; u8 res17[3]; - u8 BCDYEAR; + u8 bcdyear; #else /* little endian */ u8 res0[64]; - u8 RTCCON; + u8 rtccon; u8 res1[3]; - u8 TICNT; + u8 ticnt; u8 res2[11]; - u8 RTCALM; + u8 rtcalm; u8 res3[3]; - u8 ALMSEC; + u8 almsec; u8 res4[3]; - u8 ALMMIN; + u8 almmin; u8 res5[3]; - u8 ALMHOUR; + u8 almhour; u8 res6[3]; - u8 ALMDATE; + u8 almdate; u8 res7[3]; - u8 ALMMON; + u8 almmon; u8 res8[3]; - u8 ALMYEAR; + u8 almyear; u8 res9[3]; - u8 RTCRST; + u8 rtcrst; u8 res10[3]; - u8 BCDSEC; + u8 bcdsec; u8 res11[3]; - u8 BCDMIN; + u8 bcdmin; u8 res12[3]; - u8 BCDHOUR; + u8 bcdhour; u8 res13[3]; - u8 BCDDATE; + u8 bcddate; u8 res14[3]; - u8 BCDDAY; + u8 bcdday; u8 res15[3]; - u8 BCDMON; + u8 bcdmon; u8 res16[3]; - u8 BCDYEAR; + u8 bcdyear; u8 res17[3]; #endif }; @@ -529,34 +607,34 @@ struct s3c24x0_rtc { /* ADC (see manual chapter 16) */ struct s3c2400_adc { - u32 ADCCON; - u32 ADCDAT; + u32 adccon; + u32 adcdat; }; /* ADC (see manual chapter 16) */ struct s3c2410_adc { - u32 ADCCON; - u32 ADCTSC; - u32 ADCDLY; - u32 ADCDAT0; - u32 ADCDAT1; + u32 adccon; + u32 adctsc; + u32 adcdly; + u32 adcdat0; + u32 adcdat1; }; /* SPI (see manual chapter 22) */ struct s3c24x0_spi_channel { - u8 SPCON; + u8 spcon; u8 res1[3]; - u8 SPSTA; + u8 spsta; u8 res2[3]; - u8 SPPIN; + u8 sppin; u8 res3[3]; - u8 SPPRE; + u8 sppre; u8 res4[3]; - u8 SPTDAT; + u8 sptdat; u8 res5[3]; - u8 SPRDAT; + u8 sprdat; u8 res6[3]; u8 res7[16]; }; @@ -570,53 +648,53 @@ struct s3c24x0_spi { struct s3c2400_mmc { #ifdef __BIG_ENDIAN u8 res1[3]; - u8 MMCON; + u8 mmcon; u8 res2[3]; - u8 MMCRR; + u8 mmcrr; u8 res3[3]; - u8 MMFCON; + u8 mmfcon; u8 res4[3]; - u8 MMSTA; + u8 mmsta; u16 res5; - u16 MMFSTA; + u16 mmfsta; u8 res6[3]; - u8 MMPRE; + u8 mmpre; u16 res7; - u16 MMLEN; + u16 mmlen; u8 res8[3]; - u8 MMCR7; - u32 MMRSP[4]; + u8 mmcr7; + u32 mmrsp[4]; u8 res9[3]; - u8 MMCMD0; - u32 MMCMD1; + u8 mmcmd0; + u32 mmcmd1; u16 res10; - u16 MMCR16; + u16 mmcr16; u8 res11[3]; - u8 MMDAT; + u8 mmdat; #else - u8 MMCON; + u8 mmcon; u8 res1[3]; - u8 MMCRR; + u8 mmcrr; u8 res2[3]; - u8 MMFCON; + u8 mmfcon; u8 res3[3]; - u8 MMSTA; + u8 mmsta; u8 res4[3]; - u16 MMFSTA; + u16 mmfsta; u16 res5; - u8 MMPRE; + u8 mmpre; u8 res6[3]; - u16 MMLEN; + u16 mmlen; u16 res7; - u8 MMCR7; + u8 mmcr7; u8 res8[3]; - u32 MMRSP[4]; - u8 MMCMD0; + u32 mmrsp[4]; + u8 mmcmd0; u8 res9[3]; - u32 MMCMD1; - u16 MMCR16; + u32 mmcmd1; + u16 mmcr16; u16 res10; - u8 MMDAT; + u8 mmdat; u8 res11[3]; #endif }; @@ -624,29 +702,29 @@ struct s3c2400_mmc { /* SD INTERFACE (see S3C2410 manual chapter 19) */ struct s3c2410_sdi { - u32 SDICON; - u32 SDIPRE; - u32 SDICARG; - u32 SDICCON; - u32 SDICSTA; - u32 SDIRSP0; - u32 SDIRSP1; - u32 SDIRSP2; - u32 SDIRSP3; - u32 SDIDTIMER; - u32 SDIBSIZE; - u32 SDIDCON; - u32 SDIDCNT; - u32 SDIDSTA; - u32 SDIFSTA; + u32 sdicon; + u32 sdipre; + u32 sdicarg; + u32 sdiccon; + u32 sdicsta; + u32 sdirsp0; + u32 sdirsp1; + u32 sdirsp2; + u32 sdirsp3; + u32 sdidtimer; + u32 sdibsize; + u32 sdidcon; + u32 sdidcnt; + u32 sdidsta; + u32 sdifsta; #ifdef __BIG_ENDIAN u8 res[3]; - u8 SDIDAT; + u8 sdidat; #else - u8 SDIDAT; + u8 sdidat; u8 res[3]; #endif - u32 SDIIMSK; + u32 sdiimsk; }; #endif /*__S3C24X0_H__*/ diff --git a/arch/arm/include/asm/arch-s3c24x0/s3c24x0_cpu.h b/arch/arm/include/asm/arch-s3c24x0/s3c24x0_cpu.h index c37d4a108d7..54184c460bb 100644 --- a/arch/arm/include/asm/arch-s3c24x0/s3c24x0_cpu.h +++ b/arch/arm/include/asm/arch-s3c24x0/s3c24x0_cpu.h @@ -22,6 +22,8 @@ #include <asm/arch/s3c2400.h> #elif defined CONFIG_S3C2410 #include <asm/arch/s3c2410.h> +#elif defined CONFIG_S3C2440 + #include <asm/arch/s3c2440.h> #else #error Please define the s3c24x0 cpu type #endif diff --git a/arch/arm/include/asm/arch-s5pc1xx/mmc.h b/arch/arm/include/asm/arch-s5pc1xx/mmc.h index 68c59d13e34..48de64d9c35 100644 --- a/arch/arm/include/asm/arch-s5pc1xx/mmc.h +++ b/arch/arm/include/asm/arch-s5pc1xx/mmc.h @@ -65,7 +65,7 @@ struct mmc_host { unsigned int clock; /* Current clock (MHz) */ }; -int s5p_mmc_init(int dev_index); +int s5p_mmc_init(int dev_index, int bus_width); #endif /* __ASSEMBLY__ */ #endif diff --git a/arch/arm/include/asm/arch-s5pc1xx/uart.h b/arch/arm/include/asm/arch-s5pc1xx/uart.h index 2d7ad7ec987..f6eeab45cdc 100644 --- a/arch/arm/include/asm/arch-s5pc1xx/uart.h +++ b/arch/arm/include/asm/arch-s5pc1xx/uart.h @@ -24,6 +24,12 @@ #define __ASM_ARCH_UART_H_ #ifndef __ASSEMBLY__ +/* baudrate rest value */ +union br_rest { + unsigned short slot; /* udivslot */ + unsigned char value; /* ufracval */ +}; + struct s5p_uart { unsigned int ulcon; unsigned int ucon; @@ -38,10 +44,12 @@ struct s5p_uart { unsigned char urxh; unsigned char res2[3]; unsigned int ubrdiv; - unsigned short udivslot; - unsigned char res3[2]; - unsigned char res4[0x3d0]; + union br_rest rest; + unsigned char res3[0x3d0]; }; + +static int use_divslot = 1; + #endif /* __ASSEMBLY__ */ #endif diff --git a/board/mpl/vcma9/vcma9.c b/board/mpl/vcma9/vcma9.c index eaeec828d70..978e6fdeff9 100644 --- a/board/mpl/vcma9/vcma9.c +++ b/board/mpl/vcma9/vcma9.c @@ -78,42 +78,43 @@ int board_init(void) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* to reduce PLL lock time, adjust the LOCKTIME register */ - clk_power->LOCKTIME = 0xFFFFFF; + clk_power->locktime = 0xFFFFFF; /* configure MPLL */ - clk_power->MPLLCON = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); + clk_power->mpllcon = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); /* some delay between MPLL and UPLL */ delay (4000); /* configure UPLL */ - clk_power->UPLLCON = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); + clk_power->upllcon = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); /* some delay between MPLL and UPLL */ delay (8000); /* set up the I/O ports */ - gpio->GPACON = 0x007FFFFF; - gpio->GPBCON = 0x002AAAAA; - gpio->GPBUP = 0x000002BF; - gpio->GPCCON = 0xAAAAAAAA; - gpio->GPCUP = 0x0000FFFF; - gpio->GPDCON = 0xAAAAAAAA; - gpio->GPDUP = 0x0000FFFF; - gpio->GPECON = 0xAAAAAAAA; - gpio->GPEUP = 0x000037F7; - gpio->GPFCON = 0x00000000; - gpio->GPFUP = 0x00000000; - gpio->GPGCON = 0xFFEAFF5A; - gpio->GPGUP = 0x0000F0DC; - gpio->GPHCON = 0x0028AAAA; - gpio->GPHUP = 0x00000656; + gpio->gpacon = 0x007FFFFF; + gpio->gpbcon = 0x002AAAAA; + gpio->gpbup = 0x000002BF; + gpio->gpccon = 0xAAAAAAAA; + gpio->gpcup = 0x0000FFFF; + gpio->gpdcon = 0xAAAAAAAA; + gpio->gpdup = 0x0000FFFF; + gpio->gpecon = 0xAAAAAAAA; + gpio->gpeup = 0x000037F7; + gpio->gpfcon = 0x00000000; + gpio->gpfup = 0x00000000; + gpio->gpgcon = 0xFFEAFF5A; + gpio->gpgup = 0x0000F0DC; + gpio->gphcon = 0x0028AAAA; + gpio->gphup = 0x00000656; /* setup correct IRQ modes for NIC */ - gpio->EXTINT2 = (gpio->EXTINT2 & ~(7<<8)) | (4<<8); /* rising edge mode */ + /* rising edge mode */ + gpio->extint2 = (gpio->extint2 & ~(7<<8)) | (4<<8); /* select USB port 2 to be host or device (fix to host for now) */ - gpio->MISCCR |= 0x08; + gpio->misccr |= 0x08; /* init serial */ gd->baudrate = CONFIG_BAUDRATE; diff --git a/board/samsung/goni/goni.c b/board/samsung/goni/goni.c index 43367291132..0b09ebaf898 100644 --- a/board/samsung/goni/goni.c +++ b/board/samsung/goni/goni.c @@ -87,6 +87,6 @@ int board_mmc_init(bd_t *bis) gpio_set_drv(&s5pc110_gpio->g0, i, GPIO_DRV_4X); } - return s5p_mmc_init(0); + return s5p_mmc_init(0, 4); } #endif diff --git a/board/samsung/smdk2400/smdk2400.c b/board/samsung/smdk2400/smdk2400.c index 1294d3f1b1c..895bd7789ab 100644 --- a/board/samsung/smdk2400/smdk2400.c +++ b/board/samsung/smdk2400/smdk2400.c @@ -52,30 +52,30 @@ int board_init (void) /* memory and cpu-speed are setup before relocation */ /* change the clock to be 50 MHz 1:1:1 */ - clk_power->MPLLCON = 0x5c042; - clk_power->CLKDIVN = 0; + clk_power->mpllcon = 0x5c042; + clk_power->clkdivn = 0; /* set up the I/O ports */ - gpio->PACON = 0x3ffff; - gpio->PBCON = 0xaaaaaaaa; - gpio->PBUP = 0xffff; - gpio->PECON = 0x0; - gpio->PEUP = 0x0; + gpio->pacon = 0x3ffff; + gpio->pbcon = 0xaaaaaaaa; + gpio->pbup = 0xffff; + gpio->pecon = 0x0; + gpio->peup = 0x0; #ifdef CONFIG_HWFLOW /*CTS[0] RTS[0] INPUT INPUT TXD[0] INPUT RXD[0] */ /* 10, 10, 00, 00, 10, 00, 10 */ - gpio->PFCON=0xa22; + gpio->pfcon = 0xa22; /* Disable pull-up on Rx, Tx, CTS and RTS pins */ - gpio->PFUP=0x35; + gpio->pfup = 0x35; #else /*INPUT INPUT INPUT INPUT TXD[0] INPUT RXD[0] */ /* 00, 00, 00, 00, 10, 00, 10 */ - gpio->PFCON = 0x22; + gpio->pfcon = 0x22; /* Disable pull-up on Rx and Tx pins */ - gpio->PFUP = 0x5; + gpio->pfup = 0x5; #endif /* CONFIG_HWFLOW */ - gpio->PGCON = 0x0; - gpio->PGUP = 0x0; - gpio->OPENCR = 0x0; + gpio->pgcon = 0x0; + gpio->pgup = 0x0; + gpio->opencr = 0x0; /* arch number of SAMSUNG-Board to MACH_TYPE_SMDK2400 */ gd->bd->bi_arch_number = MACH_TYPE_SMDK2400; diff --git a/board/samsung/smdk2410/smdk2410.c b/board/samsung/smdk2410/smdk2410.c index 5d1a8bb0cf6..76a24bb9398 100644 --- a/board/samsung/smdk2410/smdk2410.c +++ b/board/samsung/smdk2410/smdk2410.c @@ -73,36 +73,36 @@ int board_init (void) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* to reduce PLL lock time, adjust the LOCKTIME register */ - clk_power->LOCKTIME = 0xFFFFFF; + clk_power->locktime = 0xFFFFFF; /* configure MPLL */ - clk_power->MPLLCON = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); + clk_power->mpllcon = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); /* some delay between MPLL and UPLL */ delay (4000); /* configure UPLL */ - clk_power->UPLLCON = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); + clk_power->upllcon = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); /* some delay between MPLL and UPLL */ delay (8000); /* set up the I/O ports */ - gpio->GPACON = 0x007FFFFF; - gpio->GPBCON = 0x00044555; - gpio->GPBUP = 0x000007FF; - gpio->GPCCON = 0xAAAAAAAA; - gpio->GPCUP = 0x0000FFFF; - gpio->GPDCON = 0xAAAAAAAA; - gpio->GPDUP = 0x0000FFFF; - gpio->GPECON = 0xAAAAAAAA; - gpio->GPEUP = 0x0000FFFF; - gpio->GPFCON = 0x000055AA; - gpio->GPFUP = 0x000000FF; - gpio->GPGCON = 0xFF95FFBA; - gpio->GPGUP = 0x0000FFFF; - gpio->GPHCON = 0x002AFAAA; - gpio->GPHUP = 0x000007FF; + gpio->gpacon = 0x007FFFFF; + gpio->gpbcon = 0x00044555; + gpio->gpbup = 0x000007FF; + gpio->gpccon = 0xAAAAAAAA; + gpio->gpcup = 0x0000FFFF; + gpio->gpdcon = 0xAAAAAAAA; + gpio->gpdup = 0x0000FFFF; + gpio->gpecon = 0xAAAAAAAA; + gpio->gpeup = 0x0000FFFF; + gpio->gpfcon = 0x000055AA; + gpio->gpfup = 0x000000FF; + gpio->gpgcon = 0xFF95FFBA; + gpio->gpgup = 0x0000FFFF; + gpio->gphcon = 0x002AFAAA; + gpio->gphup = 0x000007FF; /* arch number of SMDK2410-Board */ gd->bd->bi_arch_number = MACH_TYPE_SMDK2410; diff --git a/board/sbc2410x/sbc2410x.c b/board/sbc2410x/sbc2410x.c index 3a936778ec4..c82382dc828 100644 --- a/board/sbc2410x/sbc2410x.c +++ b/board/sbc2410x/sbc2410x.c @@ -80,40 +80,40 @@ int board_init (void) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* to reduce PLL lock time, adjust the LOCKTIME register */ - clk_power->LOCKTIME = 0xFFFFFF; + clk_power->locktime = 0xFFFFFF; /* configure MPLL */ - clk_power->MPLLCON = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); + clk_power->mpllcon = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); /* some delay between MPLL and UPLL */ delay (4000); /* configure UPLL */ - clk_power->UPLLCON = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); + clk_power->upllcon = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); /* some delay between MPLL and UPLL */ delay (8000); /* set up the I/O ports */ - gpio->GPACON = 0x007FFFFF; - gpio->GPBCON = 0x00044556; - gpio->GPBUP = 0x000007FF; - gpio->GPCCON = 0xAAAAAAAA; - gpio->GPCUP = 0x0000FFFF; - gpio->GPDCON = 0xAAAAAAAA; - gpio->GPDUP = 0x0000FFFF; - gpio->GPECON = 0xAAAAAAAA; - gpio->GPEUP = 0x0000FFFF; - gpio->GPFCON = 0x000055AA; - gpio->GPFUP = 0x000000FF; - gpio->GPGCON = 0xFF95FF3A; - gpio->GPGUP = 0x0000FFFF; - gpio->GPHCON = 0x0016FAAA; - gpio->GPHUP = 0x000007FF; - - gpio->EXTINT0=0x22222222; - gpio->EXTINT1=0x22222222; - gpio->EXTINT2=0x22222222; + gpio->gpacon = 0x007FFFFF; + gpio->gpbcon = 0x00044556; + gpio->gpbup = 0x000007FF; + gpio->gpccon = 0xAAAAAAAA; + gpio->gpcup = 0x0000FFFF; + gpio->gpdcon = 0xAAAAAAAA; + gpio->gpdup = 0x0000FFFF; + gpio->gpecon = 0xAAAAAAAA; + gpio->gpeup = 0x0000FFFF; + gpio->gpfcon = 0x000055AA; + gpio->gpfup = 0x000000FF; + gpio->gpgcon = 0xFF95FF3A; + gpio->gpgup = 0x0000FFFF; + gpio->gphcon = 0x0016FAAA; + gpio->gphup = 0x000007FF; + + gpio->extint0 = 0x22222222; + gpio->extint1 = 0x22222222; + gpio->extint2 = 0x22222222; /* arch number of SMDK2410-Board */ gd->bd->bi_arch_number = MACH_TYPE_SMDK2410; diff --git a/board/trab/cmd_trab.c b/board/trab/cmd_trab.c index ca4415c0b92..dec3c618279 100644 --- a/board/trab/cmd_trab.c +++ b/board/trab/cmd_trab.c @@ -637,28 +637,28 @@ static int adc_read (unsigned int channel) adc_init (); - padc->ADCCON &= ~ADC_STDBM; /* select normal mode */ - padc->ADCCON &= ~(0x7 << 3); /* clear the channel bits */ - padc->ADCCON |= ((channel << 3) | ADC_ENABLE_START); + padc->adccon &= ~ADC_STDBM; /* select normal mode */ + padc->adccon &= ~(0x7 << 3); /* clear the channel bits */ + padc->adccon |= ((channel << 3) | ADC_ENABLE_START); while (j--) { - if ((padc->ADCCON & ADC_ENABLE_START) == 0) + if ((padc->adccon & ADC_ENABLE_START) == 0) break; udelay (1); } if (j == 0) { printf("%s: ADC timeout\n", __FUNCTION__); - padc->ADCCON |= ADC_STDBM; /* select standby mode */ + padc->adccon |= ADC_STDBM; /* select standby mode */ return -1; } - result = padc->ADCDAT & 0x3FF; + result = padc->adcdat & 0x3FF; - padc->ADCCON |= ADC_STDBM; /* select standby mode */ + padc->adccon |= ADC_STDBM; /* select standby mode */ debug ("%s: channel %d, result[DIGIT]=%d\n", __FUNCTION__, - (padc->ADCCON >> 3) & 0x7, result); + (padc->adccon >> 3) & 0x7, result); /* * Wait for ADC to be ready for next conversion. This delay value was @@ -676,8 +676,8 @@ static void adc_init (void) padc = s3c2400_get_base_adc(); - padc->ADCCON &= ~(0xff << 6); /* clear prescaler bits */ - padc->ADCCON |= ((65 << 6) | ADC_PRSCEN); /* set prescaler */ + padc->adccon &= ~(0xff << 6); /* clear prescaler bits */ + padc->adccon |= ((65 << 6) | ADC_PRSCEN); /* set prescaler */ /* * Wait some time to avoid problem with very first call of @@ -699,10 +699,10 @@ static void led_set (unsigned int state) switch (state) { case 0: /* turn LED off */ - gpio->PADAT |= (1 << 12); + gpio->padat |= (1 << 12); break; case 1: /* turn LED on */ - gpio->PADAT &= ~(1 << 12); + gpio->padat &= ~(1 << 12); break; default: break; @@ -729,8 +729,8 @@ static void led_init (void) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* configure GPA12 as output and set to High -> LED off */ - gpio->PACON &= ~(1 << 12); - gpio->PADAT |= (1 << 12); + gpio->pacon &= ~(1 << 12); + gpio->padat |= (1 << 12); } diff --git a/board/trab/rs485.c b/board/trab/rs485.c index 6a3a4cda9ce..30336f262cf 100644 --- a/board/trab/rs485.c +++ b/board/trab/rs485.c @@ -51,16 +51,16 @@ static void rs485_setbrg (void) reg = (33000000 / (16 * 38400)) - 1; /* FIFO enable, Tx/Rx FIFO clear */ - uart->UFCON = 0x07; - uart->UMCON = 0x0; + uart->ufcon = 0x07; + uart->umcon = 0x0; /* Normal,No parity,1 stop,8 bit */ - uart->ULCON = 0x3; + uart->ulcon = 0x3; /* * tx=level,rx=edge,disable timeout int.,enable rx error int., * normal,interrupt or polling */ - uart->UCON = 0x245; - uart->UBRDIV = reg; + uart->ucon = 0x245; + uart->ubrdiv = reg; for (i = 0; i < 100; i++); } @@ -69,16 +69,16 @@ static void rs485_cfgio (void) { struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); - gpio->PFCON &= ~(0x3 << 2); - gpio->PFCON |= (0x2 << 2); /* configure GPF1 as RXD1 */ + gpio->pfcon &= ~(0x3 << 2); + gpio->pfcon |= (0x2 << 2); /* configure GPF1 as RXD1 */ - gpio->PFCON &= ~(0x3 << 6); - gpio->PFCON |= (0x2 << 6); /* configure GPF3 as TXD1 */ + gpio->pfcon &= ~(0x3 << 6); + gpio->pfcon |= (0x2 << 6); /* configure GPF3 as TXD1 */ - gpio->PFUP |= (1 << 1); /* disable pullup on GPF1 */ - gpio->PFUP |= (1 << 3); /* disable pullup on GPF3 */ + gpio->pfup |= (1 << 1); /* disable pullup on GPF1 */ + gpio->pfup |= (1 << 3); /* disable pullup on GPF3 */ - gpio->PACON &= ~(1 << 11); /* set GPA11 (RS485_DE) to output */ + gpio->pacon &= ~(1 << 11); /* set GPA11 (RS485_DE) to output */ } /* @@ -104,9 +104,10 @@ int rs485_getc (void) struct s3c24x0_uart * const uart = s3c24x0_get_base_uart(UART_NR); /* wait for character to arrive */ - while (!(uart->UTRSTAT & 0x1)); + while (!(uart->utrstat & 0x1)) + ; - return uart->URXH & 0xff; + return uart->urxh & 0xff; } /* @@ -117,9 +118,10 @@ void rs485_putc (const char c) struct s3c24x0_uart * const uart = s3c24x0_get_base_uart(UART_NR); /* wait for room in the tx FIFO */ - while (!(uart->UTRSTAT & 0x2)); + while (!(uart->utrstat & 0x2)) + ; - uart->UTXH = c; + uart->utxh = c; /* If \n, also do \r */ if (c == '\n') @@ -133,7 +135,7 @@ int rs485_tstc (void) { struct s3c24x0_uart * const uart = s3c24x0_get_base_uart(UART_NR); - return uart->UTRSTAT & 0x1; + return uart->utrstat & 0x1; } void rs485_puts (const char *s) @@ -172,9 +174,9 @@ static void set_rs485de(unsigned char rs485de_state) /* This is on PORT A bit 11 */ if(rs485de_state) - gpio->PADAT |= (1 << 11); + gpio->padat |= (1 << 11); else - gpio->PADAT &= ~(1 << 11); + gpio->padat &= ~(1 << 11); } diff --git a/board/trab/trab.c b/board/trab/trab.c index 828facd763e..0f74e8fa1b7 100644 --- a/board/trab/trab.c +++ b/board/trab/trab.c @@ -77,36 +77,36 @@ int board_init () #ifdef CONFIG_TRAB_50MHZ /* change the clock to be 50 MHz 1:1:1 */ /* MDIV:0x5c PDIV:4 SDIV:2 */ - clk_power->MPLLCON = 0x5c042; - clk_power->CLKDIVN = 0; + clk_power->mpllcon = 0x5c042; + clk_power->clkdivn = 0; #else /* change the clock to be 133 MHz 1:2:4 */ /* MDIV:0x7d PDIV:4 SDIV:1 */ - clk_power->MPLLCON = 0x7d041; - clk_power->CLKDIVN = 3; + clk_power->mpllcon = 0x7d041; + clk_power->clkdivn = 3; #endif /* set up the I/O ports */ - gpio->PACON = 0x3ffff; - gpio->PBCON = 0xaaaaaaaa; - gpio->PBUP = 0xffff; + gpio->pacon = 0x3ffff; + gpio->pbcon = 0xaaaaaaaa; + gpio->pbup = 0xffff; /* INPUT nCTS0 nRTS0 TXD[1] TXD[0] RXD[1] RXD[0] */ /* 00, 10, 10, 10, 10, 10, 10 */ - gpio->PFCON = (2<<0) | (2<<2) | (2<<4) | (2<<6) | (2<<8) | (2<<10); + gpio->pfcon = (2<<0) | (2<<2) | (2<<4) | (2<<6) | (2<<8) | (2<<10); #ifdef CONFIG_HWFLOW /* do not pull up RXD0, RXD1, TXD0, TXD1, CTS0, RTS0 */ - gpio->PFUP = (1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<4) | (1<<5); + gpio->pfup = (1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<4) | (1<<5); #else /* do not pull up RXD0, RXD1, TXD0, TXD1 */ - gpio->PFUP = (1<<0) | (1<<1) | (1<<2) | (1<<3); + gpio->pfup = (1<<0) | (1<<1) | (1<<2) | (1<<3); #endif - gpio->PGCON = 0x0; - gpio->PGUP = 0x0; - gpio->OPENCR= 0x0; + gpio->pgcon = 0x0; + gpio->pgup = 0x0; + gpio->opencr = 0x0; /* suppress flicker of the VFDs */ - gpio->MISCCR = 0x40; - gpio->PFCON |= (2<<12); + gpio->misccr = 0x40; + gpio->pfcon |= (2<<12); gd->bd->bi_arch_number = MACH_TYPE_TRAB; @@ -114,8 +114,8 @@ int board_init () gd->bd->bi_boot_params = 0x0c000100; /* Make sure both buzzers are turned off */ - gpio->PDCON |= 0x5400; - gpio->PDDAT &= ~0xE0; + gpio->pdcon |= 0x5400; + gpio->pddat &= ~0xE0; #ifdef CONFIG_VFD vfd_init_clocks(); @@ -132,7 +132,7 @@ int board_init () #ifdef CONFIG_DRIVER_S3C24X0_I2C /* Configure I/O ports PG5 und PG6 for I2C */ - gpio->PGCON = (gpio->PGCON & 0x003c00) | 0x003c00; + gpio->pgcon = (gpio->pgcon & 0x003c00) | 0x003c00; #endif /* CONFIG_DRIVER_S3C24X0_I2C */ return 0; @@ -341,14 +341,14 @@ static inline void SET_CS_TOUCH(void) { struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); - gpio->PDDAT &= 0x5FF; + gpio->pddat &= 0x5FF; } static inline void CLR_CS_TOUCH(void) { struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); - gpio->PDDAT |= 0x200; + gpio->pddat |= 0x200; } static void spi_init(void) @@ -358,20 +358,20 @@ static void spi_init(void) int i; /* Configure I/O ports. */ - gpio->PDCON = (gpio->PDCON & 0xF3FFFF) | 0x040000; - gpio->PGCON = (gpio->PGCON & 0x0F3FFF) | 0x008000; - gpio->PGCON = (gpio->PGCON & 0x0CFFFF) | 0x020000; - gpio->PGCON = (gpio->PGCON & 0x03FFFF) | 0x080000; + gpio->pdcon = (gpio->pdcon & 0xF3FFFF) | 0x040000; + gpio->pgcon = (gpio->pgcon & 0x0F3FFF) | 0x008000; + gpio->pgcon = (gpio->pgcon & 0x0CFFFF) | 0x020000; + gpio->pgcon = (gpio->pgcon & 0x03FFFF) | 0x080000; CLR_CS_TOUCH(); - spi->ch[0].SPPRE = 0x1F; /* Baudrate ca. 514kHz */ - spi->ch[0].SPPIN = 0x01; /* SPI-MOSI holds Level after last bit */ - spi->ch[0].SPCON = 0x1A; /* Polling, Prescaler, Master, CPOL=0, CPHA=1 */ + spi->ch[0].sppre = 0x1F; /* Baudrate ca. 514kHz */ + spi->ch[0].sppin = 0x01; /* SPI-MOSI holds Level after last bit */ + spi->ch[0].spcon = 0x1A; /* Polling, Prescale, Master, CPOL=0, CPHA=1 */ /* Dummy byte ensures clock to be low. */ for (i = 0; i < 10; i++) { - spi->ch[0].SPTDAT = 0xFF; + spi->ch[0].sptdat = 0xFF; } wait_transmit_done(); } @@ -380,7 +380,8 @@ static void wait_transmit_done(void) { struct s3c24x0_spi * const spi = s3c24x0_get_base_spi(); - while (!(spi->ch[0].SPSTA & 0x01)); /* wait until transfer is done */ + while (!(spi->ch[0].spsta & 0x01)) /* wait until transfer is done */ + ; } static void tsc2000_write(unsigned int page, unsigned int reg, @@ -394,13 +395,13 @@ static void tsc2000_write(unsigned int page, unsigned int reg, command |= (page << 11); command |= (reg << 5); - spi->ch[0].SPTDAT = (command & 0xFF00) >> 8; + spi->ch[0].sptdat = (command & 0xFF00) >> 8; wait_transmit_done(); - spi->ch[0].SPTDAT = (command & 0x00FF); + spi->ch[0].sptdat = (command & 0x00FF); wait_transmit_done(); - spi->ch[0].SPTDAT = (data & 0xFF00) >> 8; + spi->ch[0].sptdat = (data & 0xFF00) >> 8; wait_transmit_done(); - spi->ch[0].SPTDAT = (data & 0x00FF); + spi->ch[0].sptdat = (data & 0x00FF); wait_transmit_done(); CLR_CS_TOUCH(); diff --git a/board/trab/trab_fkt.c b/board/trab/trab_fkt.c index 268162e53ae..fe3dab351f9 100644 --- a/board/trab/trab_fkt.c +++ b/board/trab/trab_fkt.c @@ -411,28 +411,28 @@ static int adc_read (unsigned int channel) padc = s3c2400_get_base_adc(); channel &= 0x7; - padc->ADCCON &= ~ADC_STDBM; /* select normal mode */ - padc->ADCCON &= ~(0x7 << 3); /* clear the channel bits */ - padc->ADCCON |= ((channel << 3) | ADC_ENABLE_START); + padc->adccon &= ~ADC_STDBM; /* select normal mode */ + padc->adccon &= ~(0x7 << 3); /* clear the channel bits */ + padc->adccon |= ((channel << 3) | ADC_ENABLE_START); while (j--) { - if ((padc->ADCCON & ADC_ENABLE_START) == 0) + if ((padc->adccon & ADC_ENABLE_START) == 0) break; udelay (1); } if (j == 0) { printf("%s: ADC timeout\n", __FUNCTION__); - padc->ADCCON |= ADC_STDBM; /* select standby mode */ + padc->adccon |= ADC_STDBM; /* select standby mode */ return -1; } - result = padc->ADCDAT & 0x3FF; + result = padc->adcdat & 0x3FF; - padc->ADCCON |= ADC_STDBM; /* select standby mode */ + padc->adccon |= ADC_STDBM; /* select standby mode */ debug ("%s: channel %d, result[DIGIT]=%d\n", __FUNCTION__, - (padc->ADCCON >> 3) & 0x7, result); + (padc->adccon >> 3) & 0x7, result); /* * Wait for ADC to be ready for next conversion. This delay value was @@ -450,8 +450,8 @@ static void adc_init (void) padc = s3c2400_get_base_adc(); - padc->ADCCON &= ~(0xff << 6); /* clear prescaler bits */ - padc->ADCCON |= ((65 << 6) | ADC_PRSCEN); /* set prescaler */ + padc->adccon &= ~(0xff << 6); /* clear prescaler bits */ + padc->adccon |= ((65 << 6) | ADC_PRSCEN); /* set prescaler */ /* * Wait some time to avoid problem with very first call of @@ -493,10 +493,10 @@ int do_power_switch (void) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* configure GPE7 as input */ - gpio->PECON &= ~(0x3 << (2 * 7)); + gpio->pecon &= ~(0x3 << (2 * 7)); /* signal GPE7 from power switch is low active: 0=on , 1=off */ - result = ((gpio->PEDAT & (1 << 7)) == (1 << 7)) ? 0 : 1; + result = ((gpio->pedat & (1 << 7)) == (1 << 7)) ? 0 : 1; print_identifier (); printf("%d\n", result); @@ -561,17 +561,17 @@ int do_vfd_id (void) /* try to red vfd board id from the value defined by pull-ups */ - pcup_old = gpio->PCUP; - pccon_old = gpio->PCCON; + pcup_old = gpio->pcup; + pccon_old = gpio->pccon; - gpio->PCUP = (gpio->PCUP & 0xFFF0); /* activate GPC0...GPC3 pull-ups */ - gpio->PCCON = (gpio->PCCON & 0xFFFFFF00); /* configure GPC0...GPC3 as + gpio->pcup = (gpio->pcup & 0xFFF0); /* activate GPC0...GPC3 pull-ups */ + gpio->pccon = (gpio->pccon & 0xFFFFFF00); /* configure GPC0...GPC3 as * inputs */ udelay (10); /* allow signals to settle */ - vfd_board_id = (~gpio->PCDAT) & 0x000F; /* read GPC0...GPC3 port pins */ + vfd_board_id = (~gpio->pcdat) & 0x000F; /* read GPC0...GPC3 port pins */ - gpio->PCCON = pccon_old; - gpio->PCUP = pcup_old; + gpio->pccon = pccon_old; + gpio->pcup = pcup_old; /* print vfd_board_id to console */ print_identifier (); @@ -593,40 +593,40 @@ int do_buzzer (char * const *argv) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* set prescaler for timer 2, 3 and 4 */ - timers->TCFG0 &= ~0xFF00; - timers->TCFG0 |= 0x0F00; + timers->tcfg0 &= ~0xFF00; + timers->tcfg0 |= 0x0F00; /* set divider for timer 2 */ - timers->TCFG1 &= ~0xF00; - timers->TCFG1 |= 0x300; + timers->tcfg1 &= ~0xF00; + timers->tcfg1 |= 0x300; /* set frequency */ counter = (PCLK / BUZZER_FREQ) >> 9; - timers->ch[2].TCNTB = counter; - timers->ch[2].TCMPB = counter / 2; + timers->ch[2].tcntb = counter; + timers->ch[2].tcmpb = counter / 2; if (strcmp (argv[2], "on") == 0) { debug ("%s: frequency: %d\n", __FUNCTION__, BUZZER_FREQ); /* configure pin GPD7 as TOUT2 */ - gpio->PDCON &= ~0xC000; - gpio->PDCON |= 0x8000; + gpio->pdcon &= ~0xC000; + gpio->pdcon |= 0x8000; /* start */ - timers->TCON = (timers->TCON | UPDATE2 | RELOAD2) & + timers->tcon = (timers->tcon | UPDATE2 | RELOAD2) & ~INVERT2; - timers->TCON = (timers->TCON | START2) & ~UPDATE2; + timers->tcon = (timers->tcon | START2) & ~UPDATE2; return (0); } else if (strcmp (argv[2], "off") == 0) { /* stop */ - timers->TCON &= ~(START2 | RELOAD2); + timers->tcon &= ~(START2 | RELOAD2); /* configure GPD7 as output and set to low */ - gpio->PDCON &= ~0xC000; - gpio->PDCON |= 0x4000; - gpio->PDDAT &= ~0x80; + gpio->pdcon &= ~0xC000; + gpio->pdcon |= 0x4000; + gpio->pddat &= ~0x80; return (0); } @@ -640,12 +640,12 @@ int do_led (char * const *argv) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* configure PC14 and PC15 as output */ - gpio->PCCON &= ~(0xF << 28); - gpio->PCCON |= (0x5 << 28); + gpio->pccon &= ~(0xF << 28); + gpio->pccon |= (0x5 << 28); /* configure PD0 and PD4 as output */ - gpio->PDCON &= ~((0x3 << 8) | 0x3); - gpio->PDCON |= ((0x1 << 8) | 0x1); + gpio->pdcon &= ~((0x3 << 8) | 0x3); + gpio->pdcon |= ((0x1 << 8) | 0x1); switch (simple_strtoul(argv[2], NULL, 10)) { @@ -655,30 +655,30 @@ int do_led (char * const *argv) case 2: if (strcmp (argv[3], "on") == 0) - gpio->PCDAT |= (1 << 14); + gpio->pcdat |= (1 << 14); else - gpio->PCDAT &= ~(1 << 14); + gpio->pcdat &= ~(1 << 14); return 0; case 3: if (strcmp (argv[3], "on") == 0) - gpio->PCDAT |= (1 << 15); + gpio->pcdat |= (1 << 15); else - gpio->PCDAT &= ~(1 << 15); + gpio->pcdat &= ~(1 << 15); return 0; case 4: if (strcmp (argv[3], "on") == 0) - gpio->PDDAT |= (1 << 0); + gpio->pddat |= (1 << 0); else - gpio->PDDAT &= ~(1 << 0); + gpio->pddat &= ~(1 << 0); return 0; case 5: if (strcmp (argv[3], "on") == 0) - gpio->PDDAT |= (1 << 4); + gpio->pddat |= (1 << 4); else - gpio->PDDAT &= ~(1 << 4); + gpio->pddat &= ~(1 << 4); return 0; default: @@ -695,22 +695,22 @@ int do_full_bridge (char * const *argv) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* configure PD5 and PD6 as output */ - gpio->PDCON &= ~((0x3 << 5*2) | (0x3 << 6*2)); - gpio->PDCON |= ((0x1 << 5*2) | (0x1 << 6*2)); + gpio->pdcon &= ~((0x3 << 5*2) | (0x3 << 6*2)); + gpio->pdcon |= ((0x1 << 5*2) | (0x1 << 6*2)); if (strcmp (argv[2], "+") == 0) { - gpio->PDDAT |= (1 << 5); - gpio->PDDAT |= (1 << 6); + gpio->pddat |= (1 << 5); + gpio->pddat |= (1 << 6); return 0; } else if (strcmp (argv[2], "-") == 0) { - gpio->PDDAT &= ~(1 << 5); - gpio->PDDAT |= (1 << 6); + gpio->pddat &= ~(1 << 5); + gpio->pddat |= (1 << 6); return 0; } else if (strcmp (argv[2], "off") == 0) { - gpio->PDDAT &= ~(1 << 5); - gpio->PDDAT &= ~(1 << 6); + gpio->pddat &= ~(1 << 5); + gpio->pddat &= ~(1 << 6); return 0; } printf ("%s: invalid parameter %s\n", __FUNCTION__, argv[2]); @@ -804,15 +804,15 @@ int do_motor (char * const *argv) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); /* Configure I/O port */ - gpio->PGCON &= ~(0x3 << 0); - gpio->PGCON |= (0x1 << 0); + gpio->pgcon &= ~(0x3 << 0); + gpio->pgcon |= (0x1 << 0); if (strcmp (argv[2], "on") == 0) { - gpio->PGDAT &= ~(1 << 0); + gpio->pgdat &= ~(1 << 0); return 0; } if (strcmp (argv[2], "off") == 0) { - gpio->PGDAT |= (1 << 0); + gpio->pgdat |= (1 << 0); return 0; } printf ("%s: invalid parameter %s\n", __FUNCTION__, argv[2]); @@ -832,36 +832,36 @@ int do_pwm (char * const *argv) if (strcmp (argv[2], "on") == 0) { /* configure pin GPD8 as TOUT3 */ - gpio->PDCON &= ~(0x3 << 8*2); - gpio->PDCON |= (0x2 << 8*2); + gpio->pdcon &= ~(0x3 << 8*2); + gpio->pdcon |= (0x2 << 8*2); /* set prescaler for timer 2, 3 and 4 */ - timers->TCFG0 &= ~0xFF00; - timers->TCFG0 |= 0x0F00; + timers->tcfg0 &= ~0xFF00; + timers->tcfg0 |= 0x0F00; /* set divider for timer 3 */ - timers->TCFG1 &= ~(0xf << 12); - timers->TCFG1 |= (0x3 << 12); + timers->tcfg1 &= ~(0xf << 12); + timers->tcfg1 |= (0x3 << 12); /* set frequency */ counter = (PCLK / PWM_FREQ) >> 9; - timers->ch[3].TCNTB = counter; - timers->ch[3].TCMPB = counter / 2; + timers->ch[3].tcntb = counter; + timers->ch[3].tcmpb = counter / 2; /* start timer */ - timers->TCON = (timers->TCON | UPDATE3 | RELOAD3) & ~INVERT3; - timers->TCON = (timers->TCON | START3) & ~UPDATE3; + timers->tcon = (timers->tcon | UPDATE3 | RELOAD3) & ~INVERT3; + timers->tcon = (timers->tcon | START3) & ~UPDATE3; return 0; } if (strcmp (argv[2], "off") == 0) { /* stop timer */ - timers->TCON &= ~(START2 | RELOAD2); + timers->tcon &= ~(START2 | RELOAD2); /* configure pin GPD8 as output and set to 0 */ - gpio->PDCON &= ~(0x3 << 8*2); - gpio->PDCON |= (0x1 << 8*2); - gpio->PDDAT &= ~(1 << 8); + gpio->pdcon &= ~(0x3 << 8*2); + gpio->pdcon |= (0x1 << 8*2); + gpio->pddat &= ~(1 << 8); return 0; } printf ("%s: invalid parameter %s\n", __FUNCTION__, argv[2]); diff --git a/board/trab/tsc2000.c b/board/trab/tsc2000.c index 5890624f0f0..426ed9c520b 100644 --- a/board/trab/tsc2000.c +++ b/board/trab/tsc2000.c @@ -50,21 +50,21 @@ void tsc2000_spi_init(void) int i; /* Configure I/O ports. */ - gpio->PDCON = (gpio->PDCON & 0xF3FFFF) | 0x040000; - gpio->PGCON = (gpio->PGCON & 0x0F3FFF) | 0x008000; - gpio->PGCON = (gpio->PGCON & 0x0CFFFF) | 0x020000; - gpio->PGCON = (gpio->PGCON & 0x03FFFF) | 0x080000; + gpio->pdcon = (gpio->pdcon & 0xF3FFFF) | 0x040000; + gpio->pgcon = (gpio->pgcon & 0x0F3FFF) | 0x008000; + gpio->pgcon = (gpio->pgcon & 0x0CFFFF) | 0x020000; + gpio->pgcon = (gpio->pgcon & 0x03FFFF) | 0x080000; CLR_CS_TOUCH(); - spi->ch[0].SPPRE = 0x1F; /* Baud-rate ca. 514kHz */ - spi->ch[0].SPPIN = 0x01; /* SPI-MOSI holds Level after last bit */ - spi->ch[0].SPCON = 0x1A; /* Polling, Prescaler, Master, CPOL=0, + spi->ch[0].sppre = 0x1F; /* Baud-rate ca. 514kHz */ + spi->ch[0].sppin = 0x01; /* SPI-MOSI holds Level after last bit */ + spi->ch[0].spcon = 0x1A; /* Polling, Prescaler, Master, CPOL=0, CPHA=1 */ /* Dummy byte ensures clock to be low. */ for (i = 0; i < 10; i++) { - spi->ch[0].SPTDAT = 0xFF; + spi->ch[0].sptdat = 0xFF; } spi_wait_transmit_done(); } @@ -74,7 +74,8 @@ void spi_wait_transmit_done(void) { struct s3c24x0_spi * const spi = s3c24x0_get_base_spi(); - while (!(spi->ch[0].SPSTA & 0x01)); /* wait until transfer is done */ + while (!(spi->ch[0].spsta & 0x01)) /* wait until transfer is done */ + ; } @@ -85,13 +86,13 @@ void tsc2000_write(unsigned short reg, unsigned short data) SET_CS_TOUCH(); command = reg; - spi->ch[0].SPTDAT = (command & 0xFF00) >> 8; + spi->ch[0].sptdat = (command & 0xFF00) >> 8; spi_wait_transmit_done(); - spi->ch[0].SPTDAT = (command & 0x00FF); + spi->ch[0].sptdat = (command & 0x00FF); spi_wait_transmit_done(); - spi->ch[0].SPTDAT = (data & 0xFF00) >> 8; + spi->ch[0].sptdat = (data & 0xFF00) >> 8; spi_wait_transmit_done(); - spi->ch[0].SPTDAT = (data & 0x00FF); + spi->ch[0].sptdat = (data & 0x00FF); spi_wait_transmit_done(); CLR_CS_TOUCH(); @@ -106,19 +107,19 @@ unsigned short tsc2000_read (unsigned short reg) SET_CS_TOUCH(); command = 0x8000 | reg; - spi->ch[0].SPTDAT = (command & 0xFF00) >> 8; + spi->ch[0].sptdat = (command & 0xFF00) >> 8; spi_wait_transmit_done(); - spi->ch[0].SPTDAT = (command & 0x00FF); + spi->ch[0].sptdat = (command & 0x00FF); spi_wait_transmit_done(); - spi->ch[0].SPTDAT = 0xFF; + spi->ch[0].sptdat = 0xFF; spi_wait_transmit_done(); - data = spi->ch[0].SPRDAT; - spi->ch[0].SPTDAT = 0xFF; + data = spi->ch[0].sprdat; + spi->ch[0].sptdat = 0xFF; spi_wait_transmit_done(); CLR_CS_TOUCH(); - return (spi->ch[0].SPRDAT & 0x0FF) | (data << 8); + return (spi->ch[0].sprdat & 0x0FF) | (data << 8); } diff --git a/board/trab/tsc2000.h b/board/trab/tsc2000.h index 0b6253f6566..f3cecb928e2 100644 --- a/board/trab/tsc2000.h +++ b/board/trab/tsc2000.h @@ -29,45 +29,49 @@ #define _TSC2000_H_ /* temperature channel multiplexer definitions */ -#define CON_MUX0 (gpio->PCCON = (gpio->PCCON & 0x0FFFFFCFF) | 0x00000100) -#define CLR_MUX0 (gpio->PCDAT &= 0x0FFEF) -#define SET_MUX0 (gpio->PCDAT |= 0x00010) - -#define CON_MUX1 (gpio->PCCON = (gpio->PCCON & 0x0FFFFF3FF) | 0x00000400) -#define CLR_MUX1 (gpio->PCDAT &= 0x0FFDF) -#define SET_MUX1 (gpio->PCDAT |= 0x00020) - -#define CON_MUX1_ENABLE (gpio->PCCON = (gpio->PCCON & 0x0FFFFCFFF) | 0x00001000) -#define CLR_MUX1_ENABLE (gpio->PCDAT |= 0x00040) -#define SET_MUX1_ENABLE (gpio->PCDAT &= 0x0FFBF) - -#define CON_MUX2_ENABLE (gpio->PCCON = (gpio->PCCON & 0x0FFFF3FFF) | 0x00004000) -#define CLR_MUX2_ENABLE (gpio->PCDAT |= 0x00080) -#define SET_MUX2_ENABLE (gpio->PCDAT &= 0x0FF7F) - -#define CON_MUX3_ENABLE (gpio->PCCON = (gpio->PCCON & 0x0FFFCFFFF) | 0x00010000) -#define CLR_MUX3_ENABLE (gpio->PCDAT |= 0x00100) -#define SET_MUX3_ENABLE (gpio->PCDAT &= 0x0FEFF) - -#define CON_MUX4_ENABLE (gpio->PCCON = (gpio->PCCON & 0x0FFF3FFFF) | 0x00040000) -#define CLR_MUX4_ENABLE (gpio->PCDAT |= 0x00200) -#define SET_MUX4_ENABLE (gpio->PCDAT &= 0x0FDFF) - -#define CON_SEL_TEMP_V_0 (gpio->PCCON = (gpio->PCCON & 0x0FFCFFFFF) | 0x00100000) -#define CLR_SEL_TEMP_V_0 (gpio->PCDAT &= 0x0FBFF) -#define SET_SEL_TEMP_V_0 (gpio->PCDAT |= 0x00400) - -#define CON_SEL_TEMP_V_1 (gpio->PCCON = (gpio->PCCON & 0x0FF3FFFFF) | 0x00400000) -#define CLR_SEL_TEMP_V_1 (gpio->PCDAT &= 0x0F7FF) -#define SET_SEL_TEMP_V_1 (gpio->PCDAT |= 0x00800) - -#define CON_SEL_TEMP_V_2 (gpio->PCCON = (gpio->PCCON & 0x0FCFFFFFF) | 0x01000000) -#define CLR_SEL_TEMP_V_2 (gpio->PCDAT &= 0x0EFFF) -#define SET_SEL_TEMP_V_2 (gpio->PCDAT |= 0x01000) - -#define CON_SEL_TEMP_V_3 (gpio->PCCON = (gpio->PCCON & 0x0F3FFFFFF) | 0x04000000) -#define CLR_SEL_TEMP_V_3 (gpio->PCDAT &= 0x0DFFF) -#define SET_SEL_TEMP_V_3 (gpio->PCDAT |= 0x02000) +#define CON_MUX0 (gpio->pccon = (gpio->pccon & 0x0FFFFFCFF) | 0x00000100) +#define CLR_MUX0 (gpio->pcdat &= 0x0FFEF) +#define SET_MUX0 (gpio->pcdat |= 0x00010) + +#define CON_MUX1 (gpio->pccon = (gpio->pccon & 0x0FFFFF3FF) | 0x00000400) +#define CLR_MUX1 (gpio->pcdat &= 0x0FFDF) +#define SET_MUX1 (gpio->pcdat |= 0x00020) + +#define CON_MUX1_ENABLE (gpio->pccon = (gpio->pccon & 0x0FFFFCFFF) | 0x00001000) +#define CLR_MUX1_ENABLE (gpio->pcdat |= 0x00040) +#define SET_MUX1_ENABLE (gpio->pcdat &= 0x0FFBF) + +#define CON_MUX2_ENABLE (gpio->pccon = (gpio->pccon & 0x0FFFF3FFF) | 0x00004000) +#define CLR_MUX2_ENABLE (gpio->pcdat |= 0x00080) +#define SET_MUX2_ENABLE (gpio->pcdat &= 0x0FF7F) + +#define CON_MUX3_ENABLE (gpio->pccon = (gpio->pccon & 0x0FFFCFFFF) | 0x00010000) +#define CLR_MUX3_ENABLE (gpio->pcdat |= 0x00100) +#define SET_MUX3_ENABLE (gpio->pcdat &= 0x0FEFF) + +#define CON_MUX4_ENABLE (gpio->pccon = (gpio->pccon & 0x0FFF3FFFF) | 0x00040000) +#define CLR_MUX4_ENABLE (gpio->pcdat |= 0x00200) +#define SET_MUX4_ENABLE (gpio->pcdat &= 0x0FDFF) + +#define CON_SEL_TEMP_V_0 (gpio->pccon = (gpio->pccon & 0x0FFCFFFFF) | \ + 0x00100000) +#define CLR_SEL_TEMP_V_0 (gpio->pcdat &= 0x0FBFF) +#define SET_SEL_TEMP_V_0 (gpio->pcdat |= 0x00400) + +#define CON_SEL_TEMP_V_1 (gpio->pccon = (gpio->pccon & 0x0FF3FFFFF) | \ + 0x00400000) +#define CLR_SEL_TEMP_V_1 (gpio->pcdat &= 0x0F7FF) +#define SET_SEL_TEMP_V_1 (gpio->pcdat |= 0x00800) + +#define CON_SEL_TEMP_V_2 (gpio->pccon = (gpio->pccon & 0x0FCFFFFFF) | \ + 0x01000000) +#define CLR_SEL_TEMP_V_2 (gpio->pcdat &= 0x0EFFF) +#define SET_SEL_TEMP_V_2 (gpio->pcdat |= 0x01000) + +#define CON_SEL_TEMP_V_3 (gpio->pccon = (gpio->pccon & 0x0F3FFFFFF) | \ + 0x04000000) +#define CLR_SEL_TEMP_V_3 (gpio->pcdat &= 0x0DFFF) +#define SET_SEL_TEMP_V_3 (gpio->pcdat |= 0x02000) /* TSC2000 register definition */ #define TSC2000_REG_X ((0 << 11) | (0 << 5)) @@ -130,7 +134,7 @@ static inline void SET_CS_TOUCH(void) { struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); - gpio->PDDAT &= 0x5FF; + gpio->pddat &= 0x5FF; } @@ -138,7 +142,7 @@ static inline void CLR_CS_TOUCH(void) { struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); - gpio->PDDAT |= 0x200; + gpio->pddat |= 0x200; } #endif /* _TSC2000_H_ */ diff --git a/board/trab/vfd.c b/board/trab/vfd.c index b7eb8cce03c..9a2b1ba1a5a 100644 --- a/board/trab/vfd.c +++ b/board/trab/vfd.c @@ -365,12 +365,12 @@ int vfd_init_clocks (void) /* try to determine display type from the value * defined by pull-ups */ - gpio->PCUP = (gpio->PCUP & 0xFFF0); /* activate GPC0...GPC3 pullups */ - gpio->PCCON = (gpio->PCCON & 0xFFFFFF00); /* configure GPC0...GPC3 as inputs */ + gpio->pcup = (gpio->pcup & 0xFFF0); /* activate GPC0...GPC3 pullups */ + gpio->pccon = (gpio->pccon & 0xFFFFFF00); /* cfg GPC0...GPC3 inputs */ /* allow signals to settle */ for (i=0; i<10000; i++) /* udelay isn't working yet at this point! */ __asm__("NOP"); - vfd_board_id = (~gpio->PCDAT) & 0x000F; /* read GPC0...GPC3 port pins */ + vfd_board_id = (~gpio->pcdat) & 0x000F; /* read GPC0...GPC3 port pins */ VFD_DISABLE; /* activate blank for the vfd */ @@ -381,39 +381,39 @@ int vfd_init_clocks (void) /* If new board revision, then use PWM 3 as cpld-clock */ /* Enable 500 Hz timer for fill level sensor to operate properly */ /* Configure TOUT3 as functional pin, disable pull-up */ - gpio->PDCON &= ~0x30000; - gpio->PDCON |= 0x20000; - gpio->PDUP |= (1 << 8); + gpio->pdcon &= ~0x30000; + gpio->pdcon |= 0x20000; + gpio->pdup |= (1 << 8); /* Configure the prescaler */ - timers->TCFG0 &= ~0xff00; - timers->TCFG0 |= 0x0f00; + timers->tcfg0 &= ~0xff00; + timers->tcfg0 |= 0x0f00; /* Select MUX input (divider) for timer3 (1/16) */ - timers->TCFG1 &= ~0xf000; - timers->TCFG1 |= 0x3000; + timers->tcfg1 &= ~0xf000; + timers->tcfg1 |= 0x3000; /* Enable autoreload and set the counter and compare * registers to values for the 500 Hz clock * (for a given prescaler (15) and divider (16)): * counter = (66000000 / 500) >> 9; */ - timers->ch[3].TCNTB = 0x101; - timers->ch[3].TCMPB = 0x101 / 2; + timers->ch[3].tcntb = 0x101; + timers->ch[3].tcmpb = 0x101 / 2; /* Start timer */ - timers->TCON = (timers->TCON | UPDATE3 | RELOAD3) & ~INVERT3; - timers->TCON = (timers->TCON | START3) & ~UPDATE3; + timers->tcon = (timers->tcon | UPDATE3 | RELOAD3) & ~INVERT3; + timers->tcon = (timers->tcon | START3) & ~UPDATE3; } #endif /* If old board revision, then use vm-signal as cpld-clock */ - lcd->LCDCON2 = 0x00FFC000; - lcd->LCDCON3 = 0x0007FF00; - lcd->LCDCON4 = 0x00000000; - lcd->LCDCON5 = 0x00000400; - lcd->LCDCON1 = 0x00000B75; + lcd->lcdcon2 = 0x00FFC000; + lcd->lcdcon3 = 0x0007FF00; + lcd->lcdcon4 = 0x00000000; + lcd->lcdcon5 = 0x00000400; + lcd->lcdcon1 = 0x00000B75; /* VM (GPD1) is used as clock for the CPLD */ - gpio->PDCON = (gpio->PDCON & 0xFFFFFFF3) | 0x00000008; + gpio->pdcon = (gpio->pdcon & 0xFFFFFFF3) | 0x00000008; return 0; } @@ -485,40 +485,44 @@ int drv_vfd_init(void) * see manual S3C2400 */ /* Stopp LCD-Controller */ - lcd->LCDCON1 = 0x00000000; + lcd->lcdcon1 = 0x00000000; /* frame buffer startadr */ - lcd->LCDSADDR1 = gd->fb_base >> 1; + lcd->lcdsaddr1 = gd->fb_base >> 1; /* frame buffer endadr */ - lcd->LCDSADDR2 = (gd->fb_base + FRAME_BUF_SIZE) >> 1; - lcd->LCDSADDR3 = ((256/4)); - lcd->LCDCON2 = 0x000DC000; + lcd->lcdsaddr2 = (gd->fb_base + FRAME_BUF_SIZE) >> 1; + lcd->lcdsaddr3 = ((256/4)); + lcd->lcdcon2 = 0x000DC000; if(gd->vfd_type == VFD_TYPE_MN11236) - lcd->LCDCON2 = 37 << 14; /* MN11236: 38 lines */ + lcd->lcdcon2 = 37 << 14; /* MN11236: 38 lines */ else - lcd->LCDCON2 = 55 << 14; /* T119C: 56 lines */ - lcd->LCDCON3 = 0x0051000A; - lcd->LCDCON4 = 0x00000001; + lcd->lcdcon2 = 55 << 14; /* T119C: 56 lines */ + lcd->lcdcon3 = 0x0051000A; + lcd->lcdcon4 = 0x00000001; if (gd->vfd_type && vfd_inv_data) - lcd->LCDCON5 = 0x000004C0; + lcd->lcdcon5 = 0x000004C0; else - lcd->LCDCON5 = 0x00000440; + lcd->lcdcon5 = 0x00000440; /* Port pins as LCD output */ - gpio->PCCON = (gpio->PCCON & 0xFFFFFF00)| 0x000000AA; - gpio->PDCON = (gpio->PDCON & 0xFFFFFF03)| 0x000000A8; + gpio->pccon = (gpio->pccon & 0xFFFFFF00) | 0x000000AA; + gpio->pdcon = (gpio->pdcon & 0xFFFFFF03) | 0x000000A8; /* Synchronize VFD enable with LCD controller to avoid flicker */ - lcd->LCDCON1 = 0x00000B75; /* Start LCD-Controller */ - while((lcd->LCDCON5 & 0x180000)!=0x100000); /* Wait for end of VSYNC */ - while((lcd->LCDCON5 & 0x060000)!=0x040000); /* Wait for next HSYNC */ - while((lcd->LCDCON5 & 0x060000)==0x040000); - while((lcd->LCDCON5 & 0x060000)!=0x000000); + lcd->lcdcon1 = 0x00000B75; /* Start LCD-Controller */ + while ((lcd->lcdcon5 & 0x180000) != 0x100000) /* Wait for VSYNC end */ + ; + while ((lcd->lcdcon5 & 0x060000) != 0x040000) /* Wait for next HSYNC */ + ; + while ((lcd->lcdcon5 & 0x060000) == 0x040000) + ; + while ((lcd->lcdcon5 & 0x060000) != 0x000000) + ; if(gd->vfd_type) VFD_ENABLE; - debug ("LCDSADDR1: %lX\n", lcd->LCDSADDR1); - debug ("LCDSADDR2: %lX\n", lcd->LCDSADDR2); - debug ("LCDSADDR3: %lX\n", lcd->LCDSADDR3); + debug("LCDSADDR1: %lX\n", lcd->lcdsaddr1); + debug("LCDSADDR2: %lX\n", lcd->lcdsaddr2); + debug("LCDSADDR3: %lX\n", lcd->lcdsaddr3); return 0; } @@ -532,8 +536,8 @@ void disable_vfd (void) struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); VFD_DISABLE; - gpio->PDCON &= ~0xC; - gpio->PDUP &= ~0x2; + gpio->pdcon &= ~0xC; + gpio->pdup &= ~0x2; } /************************************************************************/ diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c index c8371cf730c..ba6f39bee11 100644 --- a/drivers/i2c/s3c24x0_i2c.c +++ b/drivers/i2c/s3c24x0_i2c.c @@ -58,10 +58,10 @@ static int GetI2CSDA(void) struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio(); #ifdef CONFIG_S3C2410 - return (readl(&gpio->GPEDAT) & 0x8000) >> 15; + return (readl(&gpio->gpedat) & 0x8000) >> 15; #endif #ifdef CONFIG_S3C2400 - return (readl(&gpio->PGDAT) & 0x0020) >> 5; + return (readl(&gpio->pgdat) & 0x0020) >> 5; #endif } @@ -77,10 +77,10 @@ static void SetI2CSCL(int x) struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio(); #ifdef CONFIG_S3C2410 - writel((readl(&gpio->GPEDAT) & ~0x4000) | (x & 1) << 14, &gpio->GPEDAT); + writel((readl(&gpio->gpedat) & ~0x4000) | (x & 1) << 14, &gpio->gpedat); #endif #ifdef CONFIG_S3C2400 - writel((readl(&gpio->PGDAT) & ~0x0040) | (x & 1) << 6, &gpio->PGDAT); + writel((readl(&gpio->pgdat) & ~0x0040) | (x & 1) << 6, &gpio->pgdat); #endif } @@ -90,26 +90,26 @@ static int WaitForXfer(void) int i; i = I2C_TIMEOUT * 10000; - while (!(readl(&i2c->IICCON) & I2CCON_IRPND) && (i > 0)) { + while (!(readl(&i2c->iiccon) & I2CCON_IRPND) && (i > 0)) { udelay(100); i--; } - return (readl(&i2c->IICCON) & I2CCON_IRPND) ? I2C_OK : I2C_NOK_TOUT; + return (readl(&i2c->iiccon) & I2CCON_IRPND) ? I2C_OK : I2C_NOK_TOUT; } static int IsACK(void) { struct s3c24x0_i2c *i2c = s3c24x0_get_base_i2c(); - return !(readl(&i2c->IICSTAT) & I2CSTAT_NACK); + return !(readl(&i2c->iicstat) & I2CSTAT_NACK); } static void ReadWriteByte(void) { struct s3c24x0_i2c *i2c = s3c24x0_get_base_i2c(); - writel(readl(&i2c->IICCON) & ~I2CCON_IRPND, &i2c->IICCON); + writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon); } void i2c_init(int speed, int slaveadd) @@ -122,30 +122,30 @@ void i2c_init(int speed, int slaveadd) /* wait for some time to give previous transfer a chance to finish */ i = I2C_TIMEOUT * 1000; - while ((readl(&i2c->IICSTAT) && I2CSTAT_BSY) && (i > 0)) { + while ((readl(&i2c->iicstat) && I2CSTAT_BSY) && (i > 0)) { udelay(1000); i--; } - if ((readl(&i2c->IICSTAT) & I2CSTAT_BSY) || GetI2CSDA() == 0) { + if ((readl(&i2c->iicstat) & I2CSTAT_BSY) || GetI2CSDA() == 0) { #ifdef CONFIG_S3C2410 - ulong old_gpecon = readl(&gpio->GPECON); + ulong old_gpecon = readl(&gpio->gpecon); #endif #ifdef CONFIG_S3C2400 - ulong old_gpecon = readl(&gpio->PGCON); + ulong old_gpecon = readl(&gpio->pgcon); #endif /* bus still busy probably by (most) previously interrupted transfer */ #ifdef CONFIG_S3C2410 /* set I2CSDA and I2CSCL (GPE15, GPE14) to GPIO */ - writel((readl(&gpio->GPECON) & ~0xF0000000) | 0x10000000, - &gpio->GPECON); + writel((readl(&gpio->gpecon) & ~0xF0000000) | 0x10000000, + &gpio->gpecon); #endif #ifdef CONFIG_S3C2400 /* set I2CSDA and I2CSCL (PG5, PG6) to GPIO */ - writel((readl(&gpio->PGCON) & ~0x00003c00) | 0x00001000, - &gpio->PGCON); + writel((readl(&gpio->pgcon) & ~0x00003c00) | 0x00001000, + &gpio->pgcon); #endif /* toggle I2CSCL until bus idle */ @@ -164,10 +164,10 @@ void i2c_init(int speed, int slaveadd) /* restore pin functions */ #ifdef CONFIG_S3C2410 - writel(old_gpecon, &gpio->GPECON); + writel(old_gpecon, &gpio->gpecon); #endif #ifdef CONFIG_S3C2400 - writel(old_gpecon, &gpio->PGCON); + writel(old_gpecon, &gpio->pgcon); #endif } @@ -183,13 +183,13 @@ void i2c_init(int speed, int slaveadd) /* set prescaler, divisor according to freq, also set * ACKGEN, IRQ */ - writel((div & 0x0F) | 0xA0 | ((pres == 512) ? 0x40 : 0), &i2c->IICCON); + writel((div & 0x0F) | 0xA0 | ((pres == 512) ? 0x40 : 0), &i2c->iiccon); /* init to SLAVE REVEIVE and set slaveaddr */ - writel(0, &i2c->IICSTAT); - writel(slaveadd, &i2c->IICADD); + writel(0, &i2c->iicstat); + writel(slaveadd, &i2c->iicadd); /* program Master Transmit (and implicit STOP) */ - writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->IICSTAT); + writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat); } @@ -218,47 +218,47 @@ int i2c_transfer(unsigned char cmd_type, /* Check I2C bus idle */ i = I2C_TIMEOUT * 1000; - while ((readl(&i2c->IICSTAT) & I2CSTAT_BSY) && (i > 0)) { + while ((readl(&i2c->iicstat) & I2CSTAT_BSY) && (i > 0)) { udelay(1000); i--; } - if (readl(&i2c->IICSTAT) & I2CSTAT_BSY) + if (readl(&i2c->iicstat) & I2CSTAT_BSY) return I2C_NOK_TOUT; - writel(readl(&i2c->IICCON) | 0x80, &i2c->IICCON); + writel(readl(&i2c->iiccon) | 0x80, &i2c->iiccon); result = I2C_OK; switch (cmd_type) { case I2C_WRITE: if (addr && addr_len) { - writel(chip, &i2c->IICDS); + writel(chip, &i2c->iicds); /* send START */ writel(I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP, - &i2c->IICSTAT); + &i2c->iicstat); i = 0; while ((i < addr_len) && (result == I2C_OK)) { result = WaitForXfer(); - writel(addr[i], &i2c->IICDS); + writel(addr[i], &i2c->iicds); ReadWriteByte(); i++; } i = 0; while ((i < data_len) && (result == I2C_OK)) { result = WaitForXfer(); - writel(data[i], &i2c->IICDS); + writel(data[i], &i2c->iicds); ReadWriteByte(); i++; } } else { - writel(chip, &i2c->IICDS); + writel(chip, &i2c->iicds); /* send START */ writel(I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP, - &i2c->IICSTAT); + &i2c->iicstat); i = 0; while ((i < data_len) && (result = I2C_OK)) { result = WaitForXfer(); - writel(data[i], &i2c->IICDS); + writel(data[i], &i2c->iicds); ReadWriteByte(); i++; } @@ -268,42 +268,42 @@ int i2c_transfer(unsigned char cmd_type, result = WaitForXfer(); /* send STOP */ - writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->IICSTAT); + writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->iicstat); ReadWriteByte(); break; case I2C_READ: if (addr && addr_len) { - writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->IICSTAT); - writel(chip, &i2c->IICDS); + writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat); + writel(chip, &i2c->iicds); /* send START */ - writel(readl(&i2c->IICSTAT) | I2C_START_STOP, - &i2c->IICSTAT); + writel(readl(&i2c->iicstat) | I2C_START_STOP, + &i2c->iicstat); result = WaitForXfer(); if (IsACK()) { i = 0; while ((i < addr_len) && (result == I2C_OK)) { - writel(addr[i], &i2c->IICDS); + writel(addr[i], &i2c->iicds); ReadWriteByte(); result = WaitForXfer(); i++; } - writel(chip, &i2c->IICDS); + writel(chip, &i2c->iicds); /* resend START */ writel(I2C_MODE_MR | I2C_TXRX_ENA | - I2C_START_STOP, &i2c->IICSTAT); + I2C_START_STOP, &i2c->iicstat); ReadWriteByte(); result = WaitForXfer(); i = 0; while ((i < data_len) && (result == I2C_OK)) { /* disable ACK for final READ */ if (i == data_len - 1) - writel(readl(&i2c->IICCON) - & ~0x80, &i2c->IICCON); + writel(readl(&i2c->iiccon) + & ~0x80, &i2c->iiccon); ReadWriteByte(); result = WaitForXfer(); - data[i] = readl(&i2c->IICDS); + data[i] = readl(&i2c->iicds); i++; } } else { @@ -311,11 +311,11 @@ int i2c_transfer(unsigned char cmd_type, } } else { - writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->IICSTAT); - writel(chip, &i2c->IICDS); + writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->iicstat); + writel(chip, &i2c->iicds); /* send START */ - writel(readl(&i2c->IICSTAT) | I2C_START_STOP, - &i2c->IICSTAT); + writel(readl(&i2c->iicstat) | I2C_START_STOP, + &i2c->iicstat); result = WaitForXfer(); if (IsACK()) { @@ -323,11 +323,11 @@ int i2c_transfer(unsigned char cmd_type, while ((i < data_len) && (result == I2C_OK)) { /* disable ACK for final READ */ if (i == data_len - 1) - writel(readl(&i2c->IICCON) & - ~0x80, &i2c->IICCON); + writel(readl(&i2c->iiccon) & + ~0x80, &i2c->iiccon); ReadWriteByte(); result = WaitForXfer(); - data[i] = readl(&i2c->IICDS); + data[i] = readl(&i2c->iicds); i++; } } else { @@ -336,7 +336,7 @@ int i2c_transfer(unsigned char cmd_type, } /* send STOP */ - writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->IICSTAT); + writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->iicstat); ReadWriteByte(); break; diff --git a/drivers/mmc/s5p_mmc.c b/drivers/mmc/s5p_mmc.c index 1fd425cbb67..195b5be39ea 100644 --- a/drivers/mmc/s5p_mmc.c +++ b/drivers/mmc/s5p_mmc.c @@ -352,11 +352,16 @@ static void mmc_set_ios(struct mmc *mmc) ctrl = readb(&host->reg->hostctl); /* + * WIDE8[5] + * 0 = Depend on WIDE4 + * 1 = 8-bit mode * WIDE4[1] * 1 = 4-bit mode * 0 = 1-bit mode */ - if (mmc->bus_width == 4) + if (mmc->bus_width == 8) + ctrl |= (1 << 5); + else if (mmc->bus_width == 4) ctrl |= (1 << 1); else ctrl &= ~(1 << 1); @@ -437,7 +442,7 @@ static int mmc_core_init(struct mmc *mmc) return 0; } -static int s5p_mmc_initialize(int dev_index) +static int s5p_mmc_initialize(int dev_index, int bus_width) { struct mmc *mmc; @@ -450,7 +455,11 @@ static int s5p_mmc_initialize(int dev_index) mmc->init = mmc_core_init; mmc->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; - mmc->host_caps = MMC_MODE_4BIT | MMC_MODE_HS_52MHz | MMC_MODE_HS; + if (bus_width == 8) + mmc->host_caps = MMC_MODE_8BIT; + else + mmc->host_caps = MMC_MODE_4BIT; + mmc->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; mmc->f_min = 400000; mmc->f_max = 52000000; @@ -462,7 +471,7 @@ static int s5p_mmc_initialize(int dev_index) return 0; } -int s5p_mmc_init(int dev_index) +int s5p_mmc_init(int dev_index, int bus_width) { - return s5p_mmc_initialize(dev_index); + return s5p_mmc_initialize(dev_index, bus_width); } diff --git a/drivers/mtd/nand/s3c2410_nand.c b/drivers/mtd/nand/s3c2410_nand.c index a27d47e5f1f..f70daefbfe1 100644 --- a/drivers/mtd/nand/s3c2410_nand.c +++ b/drivers/mtd/nand/s3c2410_nand.c @@ -69,11 +69,11 @@ static void s3c2410_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) chip->IO_ADDR_W = (void *)IO_ADDR_W; if (ctrl & NAND_NCE) - writel(readl(&nand->NFCONF) & ~S3C2410_NFCONF_nFCE, - &nand->NFCONF); + writel(readl(&nand->nfconf) & ~S3C2410_NFCONF_nFCE, + &nand->nfconf); else - writel(readl(&nand->NFCONF) | S3C2410_NFCONF_nFCE, - &nand->NFCONF); + writel(readl(&nand->nfconf) | S3C2410_NFCONF_nFCE, + &nand->nfconf); } if (cmd != NAND_CMD_NONE) @@ -84,7 +84,7 @@ static int s3c2410_dev_ready(struct mtd_info *mtd) { struct s3c2410_nand *nand = s3c2410_get_base_nand(); debugX(1, "dev_ready\n"); - return readl(&nand->NFSTAT) & 0x01; + return readl(&nand->nfstat) & 0x01; } #ifdef CONFIG_S3C2410_NAND_HWECC @@ -92,16 +92,16 @@ void s3c2410_nand_enable_hwecc(struct mtd_info *mtd, int mode) { struct s3c2410_nand *nand = s3c2410_get_base_nand(); debugX(1, "s3c2410_nand_enable_hwecc(%p, %d)\n", mtd, mode); - writel(readl(&nand->NFCONF) | S3C2410_NFCONF_INITECC, &nand->NFCONF); + writel(readl(&nand->nfconf) | S3C2410_NFCONF_INITECC, &nand->nfconf); } static int s3c2410_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code) { struct s3c2410_nand *nand = s3c2410_get_base_nand(); - ecc_code[0] = readb(&nand->NFECC); - ecc_code[1] = readb(&nand->NFECC + 1); - ecc_code[2] = readb(&nand->NFECC + 2); + ecc_code[0] = readb(&nand->nfecc); + ecc_code[1] = readb(&nand->nfecc + 1); + ecc_code[2] = readb(&nand->nfecc + 2); debugX(1, "s3c2410_nand_calculate_hwecc(%p,): 0x%02x 0x%02x 0x%02x\n", mtd , ecc_code[0], ecc_code[1], ecc_code[2]); @@ -130,7 +130,7 @@ int board_nand_init(struct nand_chip *nand) debugX(1, "board_nand_init()\n"); - writel(readl(&clk_power->CLKCON) | (1 << 4), &clk_power->CLKCON); + writel(readl(&clk_power->clkcon) | (1 << 4), &clk_power->clkcon); /* initialize hardware */ twrph0 = 3; @@ -141,10 +141,11 @@ int board_nand_init(struct nand_chip *nand) cfg |= S3C2410_NFCONF_TACLS(tacls - 1); cfg |= S3C2410_NFCONF_TWRPH0(twrph0 - 1); cfg |= S3C2410_NFCONF_TWRPH1(twrph1 - 1); - writel(cfg, &nand_reg->NFCONF); + writel(cfg, &nand_reg->nfconf); /* initialize nand_chip data structure */ - nand->IO_ADDR_R = nand->IO_ADDR_W = (void *)&nand_reg->NFDATA; + nand->IO_ADDR_R = (void *)&nand_reg->nfdata; + nand->IO_ADDR_W = (void *)&nand_reg->nfdata; nand->select_chip = NULL; diff --git a/drivers/rtc/s3c24x0_rtc.c b/drivers/rtc/s3c24x0_rtc.c index 04de5ca545d..7f02f0585ff 100644 --- a/drivers/rtc/s3c24x0_rtc.c +++ b/drivers/rtc/s3c24x0_rtc.c @@ -49,11 +49,11 @@ static inline void SetRTC_Access(RTC_ACCESS a) switch (a) { case RTC_ENABLE: - writeb(readb(&rtc->RTCCON) | 0x01, &rtc->RTCCON); + writeb(readb(&rtc->rtccon) | 0x01, &rtc->rtccon); break; case RTC_DISABLE: - writeb(readb(&rtc->RTCCON) & ~0x01, &rtc->RTCCON); + writeb(readb(&rtc->rtccon) & ~0x01, &rtc->rtccon); break; } } @@ -71,23 +71,23 @@ int rtc_get(struct rtc_time *tmp) /* read RTC registers */ do { - sec = readb(&rtc->BCDSEC); - min = readb(&rtc->BCDMIN); - hour = readb(&rtc->BCDHOUR); - mday = readb(&rtc->BCDDATE); - wday = readb(&rtc->BCDDAY); - mon = readb(&rtc->BCDMON); - year = readb(&rtc->BCDYEAR); - } while (sec != readb(&rtc->BCDSEC)); + sec = readb(&rtc->bcdsec); + min = readb(&rtc->bcdmin); + hour = readb(&rtc->bcdhour); + mday = readb(&rtc->bcddate); + wday = readb(&rtc->bcdday); + mon = readb(&rtc->bcdmon); + year = readb(&rtc->bcdyear); + } while (sec != readb(&rtc->bcdsec)); /* read ALARM registers */ - a_sec = readb(&rtc->ALMSEC); - a_min = readb(&rtc->ALMMIN); - a_hour = readb(&rtc->ALMHOUR); - a_date = readb(&rtc->ALMDATE); - a_mon = readb(&rtc->ALMMON); - a_year = readb(&rtc->ALMYEAR); - a_armed = readb(&rtc->RTCALM); + a_sec = readb(&rtc->almsec); + a_min = readb(&rtc->almmin); + a_hour = readb(&rtc->almhour); + a_date = readb(&rtc->almdate); + a_mon = readb(&rtc->almmon); + a_year = readb(&rtc->almyear); + a_armed = readb(&rtc->rtcalm); /* disable access to RTC registers */ SetRTC_Access(RTC_DISABLE); @@ -145,13 +145,13 @@ int rtc_set(struct rtc_time *tmp) SetRTC_Access(RTC_ENABLE); /* write RTC registers */ - writeb(sec, &rtc->BCDSEC); - writeb(min, &rtc->BCDMIN); - writeb(hour, &rtc->BCDHOUR); - writeb(mday, &rtc->BCDDATE); - writeb(wday, &rtc->BCDDAY); - writeb(mon, &rtc->BCDMON); - writeb(year, &rtc->BCDYEAR); + writeb(sec, &rtc->bcdsec); + writeb(min, &rtc->bcdmin); + writeb(hour, &rtc->bcdhour); + writeb(mday, &rtc->bcddate); + writeb(wday, &rtc->bcdday); + writeb(mon, &rtc->bcdmon); + writeb(year, &rtc->bcdyear); /* disable access to RTC registers */ SetRTC_Access(RTC_DISABLE); @@ -163,8 +163,8 @@ void rtc_reset(void) { struct s3c24x0_rtc *rtc = s3c24x0_get_base_rtc(); - writeb((readb(&rtc->RTCCON) & ~0x06) | 0x08, &rtc->RTCCON); - writeb(readb(&rtc->RTCCON) & ~(0x08 | 0x01), &rtc->RTCCON); + writeb((readb(&rtc->rtccon) & ~0x06) | 0x08, &rtc->rtccon); + writeb(readb(&rtc->rtccon) & ~(0x08 | 0x01), &rtc->rtccon); } #endif diff --git a/drivers/serial/serial_s3c24x0.c b/drivers/serial/serial_s3c24x0.c index 8a3e30209cf..f42b15e45ec 100644 --- a/drivers/serial/serial_s3c24x0.c +++ b/drivers/serial/serial_s3c24x0.c @@ -101,7 +101,7 @@ void _serial_setbrg(const int dev_index) /* value is calculated so : (int)(PCLK/16./baudrate) -1 */ reg = get_PCLK() / (16 * gd->baudrate) - 1; - writel(reg, &uart->UBRDIV); + writel(reg, &uart->ubrdiv); for (i = 0; i < 100; i++) /* Delay */ ; } @@ -131,26 +131,26 @@ static int serial_init_dev(const int dev_index) #endif /* FIFO enable, Tx/Rx FIFO clear */ - writel(0x07, &uart->UFCON); - writel(0x0, &uart->UMCON); + writel(0x07, &uart->ufcon); + writel(0x0, &uart->umcon); /* Normal,No parity,1 stop,8 bit */ - writel(0x3, &uart->ULCON); + writel(0x3, &uart->ulcon); /* * tx=level,rx=edge,disable timeout int.,enable rx error int., * normal,interrupt or polling */ - writel(0x245, &uart->UCON); + writel(0x245, &uart->ucon); #ifdef CONFIG_HWFLOW - writel(0x1, &uart->UMCON); /* RTS up */ + writel(0x1, &uart->umcon); /* rts up */ #endif /* FIXME: This is sooooooooooooooooooo ugly */ #if defined(CONFIG_ARCH_GTA02_v1) || defined(CONFIG_ARCH_GTA02_v2) /* we need auto hw flow control on the gsm and gps port */ if (dev_index == 0 || dev_index == 1) - writel(0x10, &uart->UMCON); + writel(0x10, &uart->umcon); #endif _serial_setbrg(dev_index); @@ -176,10 +176,10 @@ int _serial_getc(const int dev_index) { struct s3c24x0_uart *uart = s3c24x0_get_base_uart(dev_index); - while (!(readl(&uart->UTRSTAT) & 0x1)) + while (!(readl(&uart->utrstat) & 0x1)) /* wait for character to arrive */ ; - return readb(&uart->URXH) & 0xff; + return readb(&uart->urxh) & 0xff; } #if defined(CONFIG_SERIAL_MULTI) @@ -237,15 +237,15 @@ void _serial_putc(const char c, const int dev_index) return; #endif - while (!(readl(&uart->UTRSTAT) & 0x2)) + while (!(readl(&uart->utrstat) & 0x2)) /* wait for room in the tx FIFO */ ; #ifdef CONFIG_HWFLOW - while (hwflow && !(readl(&uart->UMSTAT) & 0x1)) + while (hwflow && !(readl(&uart->umstat) & 0x1)) /* Wait for CTS up */ ; #endif - writeb(c, &uart->UTXH); + writeb(c, &uart->utxh); /* If \n, also do \r */ if (c == '\n') @@ -272,7 +272,7 @@ int _serial_tstc(const int dev_index) { struct s3c24x0_uart *uart = s3c24x0_get_base_uart(dev_index); - return readl(&uart->UTRSTAT) & 0x1; + return readl(&uart->utrstat) & 0x1; } #if defined(CONFIG_SERIAL_MULTI) diff --git a/drivers/serial/serial_s5p.c b/drivers/serial/serial_s5p.c index 77096643f1f..36333c3d49a 100644 --- a/drivers/serial/serial_s5p.c +++ b/drivers/serial/serial_s5p.c @@ -70,7 +70,11 @@ void serial_setbrg_dev(const int dev_index) val = uclk / baudrate; writel(val / 16 - 1, &uart->ubrdiv); - writew(udivslot[val % 16], &uart->udivslot); + + if (use_divslot) + writew(udivslot[val % 16], &uart->rest.slot); + else + writeb(val % 16, &uart->rest.value); } /* |