diff options
Diffstat (limited to 'arch/arm/dts/stm32f746.dtsi')
| -rw-r--r-- | arch/arm/dts/stm32f746.dtsi | 747 |
1 files changed, 517 insertions, 230 deletions
diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi index afa7832f893..f48d06a80d1 100644 --- a/arch/arm/dts/stm32f746.dtsi +++ b/arch/arm/dts/stm32f746.dtsi @@ -1,9 +1,4 @@ /* - * Copyright 2016 - Michael Kurz <michi.kurz@gmail.com> - * Copyright 2016 - Vikas MANOCHA <vikas.manocha@st.com> - * - * Based on: - * stm32f429.dtsi from Linux * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com> * * This file is dual-licensed: you can use it either under the terms @@ -45,8 +40,8 @@ * OTHER DEALINGS IN THE SOFTWARE. */ +#include "skeleton.dtsi" #include "armv7-m.dtsi" -#include <dt-bindings/pinctrl/stm32f746-pinfunc.h> #include <dt-bindings/clock/stm32fx-clock.h> #include <dt-bindings/mfd/stm32f7-rcc.h> @@ -57,292 +52,584 @@ compatible = "fixed-clock"; clock-frequency = <0>; }; -}; + + clk-lse { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + }; + + clk-lsi { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32000>; + }; + + clk_i2s_ckin: clk-i2s-ckin { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <48000000>; + }; + }; soc { - u-boot,dm-pre-reloc; - mac: ethernet@40028000 { - compatible = "st,stm32-dwmac"; - reg = <0x40028000 0x8000>; - reg-names = "stmmaceth"; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(ETHMAC)>, - <&rcc 0 STM32F7_AHB1_CLOCK(ETHMACTX)>, - <&rcc 0 STM32F7_AHB1_CLOCK(ETHMACRX)>; - interrupts = <61>, <62>; - interrupt-names = "macirq", "eth_wake_irq"; - snps,pbl = <8>; - snps,mixed-burst; - dma-ranges; - status = "disabled"; - }; - - fmc: fmc@A0000000 { - compatible = "st,stm32-fmc"; - reg = <0xA0000000 0x1000>; - clocks = <&rcc 0 STM32F7_AHB3_CLOCK(FMC)>; - u-boot,dm-pre-reloc; - }; - - qspi: quadspi@A0001000 { - compatible = "st,stm32-qspi"; + timer2: timer@40000000 { + compatible = "st,stm32-timer"; + reg = <0x40000000 0x400>; + interrupts = <28>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM2)>; + status = "disabled"; + }; + + timers2: timers@40000000 { #address-cells = <1>; #size-cells = <0>; - reg = <0xA0001000 0x1000>, <0x90000000 0x10000000>; - reg-names = "qspi", "qspi_mm"; - interrupts = <92>; - spi-max-frequency = <108000000>; - clocks = <&rcc 0 STM32F7_AHB3_CLOCK(QSPI)>; - resets = <&rcc STM32F7_AHB3_RESET(QSPI)>; + compatible = "st,stm32-timers"; + reg = <0x40000000 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM2)>; + clock-names = "int"; status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@1 { + compatible = "st,stm32-timer-trigger"; + reg = <1>; + status = "disabled"; + }; }; - usart1: serial@40011000 { - compatible = "st,stm32f7-usart", "st,stm32f7-uart"; - reg = <0x40011000 0x400>; - interrupts = <37>; - clocks = <&rcc 0 STM32F7_APB2_CLOCK(USART1)>; + + timer3: timer@40000400 { + compatible = "st,stm32-timer"; + reg = <0x40000400 0x400>; + interrupts = <29>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM3)>; status = "disabled"; - u-boot,dm-pre-reloc; }; - pwrcfg: power-config@58024800 { - compatible = "syscon"; - reg = <0x40007000 0x400>; + timers3: timers@40000400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000400 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM3)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@2 { + compatible = "st,stm32-timer-trigger"; + reg = <2>; + status = "disabled"; + }; }; - rcc: rcc@40023810 { - #reset-cells = <1>; - #clock-cells = <2>; - compatible = "st,stm32f746-rcc", "st,stm32-rcc"; - reg = <0x40023800 0x400>; - clocks = <&clk_hse>; - st,syscfg = <&pwrcfg>; - u-boot,dm-pre-reloc; + timer4: timer@40000800 { + compatible = "st,stm32-timer"; + reg = <0x40000800 0x400>; + interrupts = <30>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM4)>; + status = "disabled"; }; - pinctrl: pin-controller { + timers4: timers@40000800 { #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32f746-pinctrl"; - ranges = <0 0x40020000 0x3000>; - u-boot,dm-pre-reloc; - pins-are-numbered; - - gpioa: gpio@40020000 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x0 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOA)>; - st,bank-name = "GPIOA"; - u-boot,dm-pre-reloc; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000800 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM4)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; - gpiob: gpio@40020400 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x400 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOB)>; - st,bank-name = "GPIOB"; - u-boot,dm-pre-reloc; + timer@3 { + compatible = "st,stm32-timer-trigger"; + reg = <3>; + status = "disabled"; }; + }; + + timer5: timer@40000c00 { + compatible = "st,stm32-timer"; + reg = <0x40000c00 0x400>; + interrupts = <50>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM5)>; + }; + timers5: timers@40000c00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000C00 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM5)>; + clock-names = "int"; + status = "disabled"; - gpioc: gpio@40020800 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x800 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOC)>; - st,bank-name = "GPIOC"; - u-boot,dm-pre-reloc; + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; - gpiod: gpio@40020c00 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0xc00 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOD)>; - st,bank-name = "GPIOD"; - u-boot,dm-pre-reloc; + timer@4 { + compatible = "st,stm32-timer-trigger"; + reg = <4>; + status = "disabled"; }; + }; - gpioe: gpio@40021000 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x1000 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOE)>; - st,bank-name = "GPIOE"; - u-boot,dm-pre-reloc; - }; + timer6: timer@40001000 { + compatible = "st,stm32-timer"; + reg = <0x40001000 0x400>; + interrupts = <54>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM6)>; + status = "disabled"; + }; + + timers6: timers@40001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001000 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM6)>; + clock-names = "int"; + status = "disabled"; - gpiof: gpio@40021400 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x1400 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOF)>; - st,bank-name = "GPIOF"; - u-boot,dm-pre-reloc; + timer@5 { + compatible = "st,stm32-timer-trigger"; + reg = <5>; + status = "disabled"; }; + }; - gpiog: gpio@40021800 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x1800 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOG)>; - st,bank-name = "GPIOG"; - u-boot,dm-pre-reloc; + timer7: timer@40001400 { + compatible = "st,stm32-timer"; + reg = <0x40001400 0x400>; + interrupts = <55>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM7)>; + status = "disabled"; + }; + + timers7: timers@40001400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001400 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM7)>; + clock-names = "int"; + status = "disabled"; + + timer@6 { + compatible = "st,stm32-timer-trigger"; + reg = <6>; + status = "disabled"; }; + }; + + timers12: timers@40001800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001800 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM12)>; + clock-names = "int"; + status = "disabled"; - gpioh: gpio@40021c00 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x1c00 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOH)>; - st,bank-name = "GPIOH"; - u-boot,dm-pre-reloc; + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; - gpioi: gpio@40022000 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x2000 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOI)>; - st,bank-name = "GPIOI"; - u-boot,dm-pre-reloc; + timer@11 { + compatible = "st,stm32-timer-trigger"; + reg = <11>; + status = "disabled"; }; + }; - gpioj: gpio@40022400 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x2400 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOJ)>; - st,bank-name = "GPIOJ"; - u-boot,dm-pre-reloc; + timers13: timers@40001c00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001C00 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM13)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; + }; - gpiok: gpio@40022800 { - gpio-controller; - #gpio-cells = <2>; - compatible = "st,stm32-gpio"; - reg = <0x2800 0x400>; - clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOK)>; - st,bank-name = "GPIOK"; - u-boot,dm-pre-reloc; + timers14: timers@40002000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40002000 0x400>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM14)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; + }; + + rtc: rtc@40002800 { + compatible = "st,stm32-rtc"; + reg = <0x40002800 0x400>; + clocks = <&rcc 1 CLK_RTC>; + clock-names = "ck_rtc"; + assigned-clocks = <&rcc 1 CLK_RTC>; + assigned-clock-parents = <&rcc 1 CLK_LSE>; + interrupt-parent = <&exti>; + interrupts = <17 1>; + interrupt-names = "alarm"; + st,syscfg = <&pwrcfg 0x00 0x100>; + status = "disabled"; + }; + + usart2: serial@40004400 { + compatible = "st,stm32f7-uart"; + reg = <0x40004400 0x400>; + interrupts = <38>; + clocks = <&rcc 1 CLK_USART2>; + status = "disabled"; + }; + + usart3: serial@40004800 { + compatible = "st,stm32f7-uart"; + reg = <0x40004800 0x400>; + interrupts = <39>; + clocks = <&rcc 1 CLK_USART3>; + status = "disabled"; + }; + + usart4: serial@40004c00 { + compatible = "st,stm32f7-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + clocks = <&rcc 1 CLK_UART4>; + status = "disabled"; + }; + + usart5: serial@40005000 { + compatible = "st,stm32f7-uart"; + reg = <0x40005000 0x400>; + interrupts = <53>; + clocks = <&rcc 1 CLK_UART5>; + status = "disabled"; + }; - sdio_pins: sdio_pins@0 { - pins { - pinmux = <STM32F746_PC8_FUNC_SDMMC1_D0>, - <STM32F746_PC9_FUNC_SDMMC1_D1>, - <STM32F746_PC10_FUNC_SDMMC1_D2>, - <STM32F746_PC11_FUNC_SDMMC1_D3>, - <STM32F746_PC12_FUNC_SDMMC1_CK>, - <STM32F746_PD2_FUNC_SDMMC1_CMD>; - drive-push-pull; - slew-rate = <2>; - }; + i2c1: i2c@40005400 { + compatible = "st,stm32f7-i2c"; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32F7_APB1_RESET(I2C1)>; + clocks = <&rcc 1 CLK_I2C1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@40005800 { + compatible = "st,stm32f7-i2c"; + reg = <0x40005800 0x400>; + interrupts = <33>, + <34>; + resets = <&rcc STM32F7_APB1_RESET(I2C2)>; + clocks = <&rcc 1 CLK_I2C2>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@40005C00 { + compatible = "st,stm32f7-i2c"; + reg = <0x40005C00 0x400>; + interrupts = <72>, + <73>; + resets = <&rcc STM32F7_APB1_RESET(I2C3)>; + clocks = <&rcc 1 CLK_I2C3>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@40006000 { + compatible = "st,stm32f7-i2c"; + reg = <0x40006000 0x400>; + interrupts = <95>, + <96>; + resets = <&rcc STM32F7_APB1_RESET(I2C4)>; + clocks = <&rcc 1 CLK_I2C4>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + cec: cec@40006c00 { + compatible = "st,stm32-cec"; + reg = <0x40006C00 0x400>; + interrupts = <94>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(CEC)>, <&rcc 1 CLK_HDMI_CEC>; + clock-names = "cec", "hdmi-cec"; + status = "disabled"; + }; + + usart7: serial@40007800 { + compatible = "st,stm32f7-uart"; + reg = <0x40007800 0x400>; + interrupts = <82>; + clocks = <&rcc 1 CLK_UART7>; + status = "disabled"; + }; + + usart8: serial@40007c00 { + compatible = "st,stm32f7-uart"; + reg = <0x40007c00 0x400>; + interrupts = <83>; + clocks = <&rcc 1 CLK_UART8>; + status = "disabled"; + }; + + timers1: timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM1)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; - sdio_pins_od: sdio_pins_od@0 { - pins1 { - pinmux = <STM32F746_PC8_FUNC_SDMMC1_D0>, - <STM32F746_PC9_FUNC_SDMMC1_D1>, - <STM32F746_PC10_FUNC_SDMMC1_D2>, - <STM32F746_PC11_FUNC_SDMMC1_D3>, - <STM32F746_PC12_FUNC_SDMMC1_CK>; - drive-push-pull; - slew-rate = <2>; - }; - - pins2 { - pinmux = <STM32F746_PD2_FUNC_SDMMC1_CMD>; - drive-open-drain; - slew-rate = <2>; - }; + timer@0 { + compatible = "st,stm32-timer-trigger"; + reg = <0>; + status = "disabled"; }; + }; - sdio_pins_b: sdio_pins_b@0 { - pins { - pinmux = <STM32F769_PG9_FUNC_SDMMC2_D0>, - <STM32F769_PG10_FUNC_SDMMC2_D1>, - <STM32F769_PB3_FUNC_SDMMC2_D2>, - <STM32F769_PB4_FUNC_SDMMC2_D3>, - <STM32F769_PD6_FUNC_SDMMC2_CLK>, - <STM32F769_PD7_FUNC_SDMMC2_CMD>; - drive-push-pull; - slew-rate = <2>; - }; + timers8: timers@40010400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010400 0x400>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM8)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; }; - sdio_pins_od_b: sdio_pins_od_b@0 { - pins1 { - pinmux = <STM32F769_PG9_FUNC_SDMMC2_D0>, - <STM32F769_PG10_FUNC_SDMMC2_D1>, - <STM32F769_PB3_FUNC_SDMMC2_D2>, - <STM32F769_PB4_FUNC_SDMMC2_D3>, - <STM32F769_PD6_FUNC_SDMMC2_CLK>; - drive-push-pull; - slew-rate = <2>; - }; - - pins2 { - pinmux = <STM32F769_PD7_FUNC_SDMMC2_CMD>; - drive-open-drain; - slew-rate = <2>; - }; + timer@7 { + compatible = "st,stm32-timer-trigger"; + reg = <7>; + status = "disabled"; }; + }; + usart1: serial@40011000 { + compatible = "st,stm32f7-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 1 CLK_USART1>; + status = "disabled"; }; - sdio: sdio@40012c00 { - compatible = "st,stm32f4xx-sdio"; - reg = <0x40012c00 0x400>; - clocks = <&rcc 0 171>; - interrupts = <49>; + + usart6: serial@40011400 { + compatible = "st,stm32f7-uart"; + reg = <0x40011400 0x400>; + interrupts = <71>; + clocks = <&rcc 1 CLK_USART6>; status = "disabled"; - pinctrl-0 = <&sdio_pins>; - pinctrl-1 = <&sdio_pins_od>; - pinctrl-names = "default", "opendrain"; - max-frequency = <48000000>; }; sdio2: sdio2@40011c00 { - compatible = "st,stm32f4xx-sdio"; + compatible = "arm,pl180", "arm,primecell"; + arm,primecell-periphid = <0x00880180>; reg = <0x40011c00 0x400>; - clocks = <&rcc 0 167>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(SDMMC2)>; + clock-names = "apb_pclk"; interrupts = <103>; + max-frequency = <48000000>; status = "disabled"; - pinctrl-0 = <&sdio_pins_b>; - pinctrl-1 = <&sdio_pins_od_b>; - pinctrl-names = "default", "opendrain"; + }; + + sdio1: sdio1@40012c00 { + compatible = "arm,pl180", "arm,primecell"; + arm,primecell-periphid = <0x00880180>; + reg = <0x40012c00 0x400>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(SDMMC1)>; + clock-names = "apb_pclk"; + interrupts = <49>; max-frequency = <48000000>; + status = "disabled"; }; - timer5: timer@40000c00 { - compatible = "st,stm32-timer"; - reg = <0x40000c00 0x400>; - interrupts = <50>; - clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM5)>; + syscfg: system-config@40013800 { + compatible = "syscon"; + reg = <0x40013800 0x400>; + }; + + exti: interrupt-controller@40013c00 { + compatible = "st,stm32-exti"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x40013C00 0x400>; + interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <42>, <62>, <76>; + }; + + timers9: timers@40014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014000 0x400>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM9)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@8 { + compatible = "st,stm32-timer-trigger"; + reg = <8>; + status = "disabled"; + }; + }; + + timers10: timers@40014400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014400 0x400>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM10)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + timers11: timers@40014800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014800 0x400>; + clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM11)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + pwrcfg: power-config@40007000 { + compatible = "syscon"; + reg = <0x40007000 0x400>; + }; + + crc: crc@40023000 { + compatible = "st,stm32f7-crc"; + reg = <0x40023000 0x400>; + clocks = <&rcc 0 12>; + status = "disabled"; + }; + + rcc: rcc@40023800 { + #reset-cells = <1>; + #clock-cells = <2>; + compatible = "st,stm32f746-rcc", "st,stm32-rcc"; + reg = <0x40023800 0x400>; + clocks = <&clk_hse>, <&clk_i2s_ckin>; + st,syscfg = <&pwrcfg>; + assigned-clocks = <&rcc 1 CLK_HSE_RTC>; + assigned-clock-rates = <1000000>; + }; + + dma1: dma@40026000 { + compatible = "st,stm32-dma"; + reg = <0x40026000 0x400>; + interrupts = <11>, + <12>, + <13>, + <14>, + <15>, + <16>, + <17>, + <47>; + clocks = <&rcc 0 STM32F7_AHB1_CLOCK(DMA1)>; + #dma-cells = <4>; + status = "disabled"; + }; + + dma2: dma@40026400 { + compatible = "st,stm32-dma"; + reg = <0x40026400 0x400>; + interrupts = <56>, + <57>, + <58>, + <59>, + <60>, + <68>, + <69>, + <70>; + clocks = <&rcc 0 STM32F7_AHB1_CLOCK(DMA2)>; + #dma-cells = <4>; + st,mem2mem; + status = "disabled"; + }; + + usbotg_hs: usb@40040000 { + compatible = "st,stm32f7-hsotg"; + reg = <0x40040000 0x40000>; + interrupts = <77>; + clocks = <&rcc 0 STM32F7_AHB1_CLOCK(OTGHS)>; + clock-names = "otg"; + g-rx-fifo-size = <256>; + g-np-tx-fifo-size = <32>; + g-tx-fifo-size = <128 128 64 64 64 64 32 32>; + status = "disabled"; }; - ltdc: display-controller@40016800 { - compatible = "st,stm32-ltdc"; - reg = <0x40016800 0x200>; - resets = <&rcc STM32F7_APB2_RESET(LTDC)>; - clocks = <&rcc 0 STM32F7_APB2_CLOCK(LTDC)>; - u-boot,dm-pre-reloc; + usbotg_fs: usb@50000000 { + compatible = "st,stm32f4x9-fsotg"; + reg = <0x50000000 0x40000>; + interrupts = <67>; + clocks = <&rcc 0 STM32F7_AHB2_CLOCK(OTGFS)>; + clock-names = "otg"; status = "disabled"; }; }; }; &systick { + clocks = <&rcc 1 0>; status = "okay"; }; |