diff options
Diffstat (limited to 'common')
| -rw-r--r-- | common/spl/Kconfig | 54 |
1 files changed, 22 insertions, 32 deletions
diff --git a/common/spl/Kconfig b/common/spl/Kconfig index 25078432a7e..9952a9b94c1 100644 --- a/common/spl/Kconfig +++ b/common/spl/Kconfig @@ -1,5 +1,3 @@ -menu "SPL / TPL / VPL" - config SUPPORT_SPL bool @@ -13,15 +11,16 @@ config SPL_DFU_NO_RESET bool config SPL - bool + bool "Enable SPL" depends on SUPPORT_SPL - prompt "Enable SPL" help If you want to build SPL as well as the normal image, say Y. +menu "SPL configuration options" + depends on SPL + config SPL_FRAMEWORK bool "Support SPL based upon the common SPL framework" - depends on SPL default y help Enable the SPL framework under common/spl/. This framework @@ -39,7 +38,6 @@ config SPL_FRAMEWORK_BOARD_INIT_F config SPL_SIZE_LIMIT hex "Maximum size of SPL image" - depends on SPL default 0x11000 if ARCH_MX6 && !MX6_OCRAM_256KB default 0x31000 if ARCH_MX6 && MX6_OCRAM_256KB default 0x0 @@ -122,7 +120,7 @@ config SPL_BSS_START_ADDR choice prompt "Enforce SPL BSS limit" - depends on SPL && !PPC + depends on !PPC default SPL_BSS_LIMIT help In some platforms we only want to enforce a limit on the size of the @@ -203,7 +201,7 @@ source "common/spl/Kconfig.nxp" config HANDOFF bool "Pass hand-off information from SPL to U-Boot proper" - depends on SPL && BLOBLIST + depends on BLOBLIST help It is useful to be able to pass information from SPL to U-Boot proper to preserve state that is known in SPL and is needed in U-Boot. @@ -211,8 +209,6 @@ config HANDOFF in boot. It is available in gd->handoff. The state state is set up in SPL (or TPL if that is being used). -if SPL - config SPL_HANDOFF bool "Pass hand-off information from SPL to U-Boot proper" depends on HANDOFF && SPL_BLOBLIST @@ -300,8 +296,7 @@ config SPL_LEGACY_IMAGE_CRC_CHECK are correct, without further integrity checks. config SPL_SYS_MALLOC_SIMPLE - bool - prompt "Only use malloc_simple functions in the SPL" + bool "Only use malloc_simple functions in the SPL" help Say Y here to only use the *_simple malloc functions from malloc_simple.c, rather then using the versions from dlmalloc.c; @@ -1020,7 +1015,6 @@ config SPL_NOR_SUPPORT config SPL_XIP_SUPPORT bool "Support XIP" - depends on SPL help Enable support for execute in place of U-Boot or kernel image. There is no need to copy image from flash to ram if flash supports execute @@ -1131,7 +1125,6 @@ config SPL_POST_MEM_SUPPORT config SPL_DM_RESET bool "Support reset drivers" - depends on SPL help Enable support for reset control in SPL. That can be useful in SPL to handle IP reset in driver, as in U-Boot, @@ -1472,35 +1465,32 @@ config SPL_TARGET On some platforms we need to have 'make' run additional build target rules. If required on your platform, enter it here, otherwise leave blank. + +config SPL_AT91_MCK_BYPASS + bool "Use external clock signal as a source of main clock for AT91 platforms" + depends on ARCH_AT91 + help + Use external 8 to 24 Mhz clock signal as source of main clock instead + of an external crystal oscillator. + This option disables the internal driving on the XOUT pin. + The external source has to provide a stable clock on the XIN pin. + If this option is disabled, the SoC expects a crystal oscillator + that needs driving on both XIN and XOUT lines. +endmenu + config TPL - bool depends on SUPPORT_TPL - prompt "Enable TPL" + bool "Enable TPL" help If you want to build TPL as well as the normal image and SPL, say Y. source "common/spl/Kconfig.tpl" config VPL - bool depends on SUPPORT_SPL - prompt "Enable VPL" + bool "Enable VPL" help If you want to build VPL as well as the normal image, TPL and SPL, say Y. source "common/spl/Kconfig.vpl" - -config SPL_AT91_MCK_BYPASS - bool "Use external clock signal as a source of main clock for AT91 platforms" - depends on ARCH_AT91 - help - Use external 8 to 24 Mhz clock signal as source of main clock instead - of an external crystal oscillator. - This option disables the internal driving on the XOUT pin. - The external source has to provide a stable clock on the XIN pin. - If this option is disabled, the SoC expects a crystal oscillator - that needs driving on both XIN and XOUT lines. - -endif # SPL -endmenu |