diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/usb/host/ehci-mx6.c | 52 |
1 files changed, 7 insertions, 45 deletions
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c index 99fd0e71834..68f6ecc8722 100644 --- a/drivers/usb/host/ehci-mx6.c +++ b/drivers/usb/host/ehci-mx6.c @@ -550,49 +550,6 @@ static int ehci_usb_of_to_plat(struct udevice *dev) return 0; } -static int ehci_usb_bind(struct udevice *dev) -{ - /* - * TODO: - * This driver is only partly converted to DT probing and still uses - * a tremendous amount of hard-coded addresses. To make things worse, - * the driver depends on specific sequential indexing of controllers, - * from which it derives offsets in the PHY and ANATOP register sets. - * - * Here we attempt to calculate these indexes from DT information as - * well as we can. The USB controllers on all existing iMX6 SoCs - * are placed next to each other, at addresses incremented by 0x200, - * and iMX7 their addresses are shifted by 0x10000. - * Thus, the index is derived from the multiple of 0x200 (0x10000 for - * iMX7) offset from the first controller address. - * - * However, to complete conversion of this driver to DT probing, the - * following has to be done: - * - DM clock framework support for iMX must be implemented - * - usb_power_config() has to be converted to clock framework - * -> Thus, the ad-hoc "index" variable goes away. - * - USB PHY handling has to be factored out into separate driver - * -> Thus, the ad-hoc "index" variable goes away from the PHY - * code, the PHY driver must parse it's address from DT. This - * USB driver must find the PHY driver via DT phandle. - * -> usb_power_config() shall be moved to PHY driver - * With these changes in place, the ad-hoc indexing goes away and - * the driver is fully converted to DT probing. - */ - - /* - * FIXME: This cannot work with the new sequence numbers. - * Please complete the DM conversion. - * - * u32 controller_spacing = is_mx7() ? 0x10000 : 0x200; - * fdt_addr_t addr = devfdt_get_addr_index(dev, 0); - * - * dev->req_seq = (addr - USB_BASE_ADDR) / controller_spacing; - */ - - return 0; -} - static int mx6_parse_dt_addrs(struct udevice *dev) { struct ehci_mx6_priv_data *priv = dev_get_priv(dev); @@ -600,6 +557,7 @@ static int mx6_parse_dt_addrs(struct udevice *dev) const void *blob = gd->fdt_blob; int offset = dev_of_offset(dev); void *__iomem addr; + int ret, devnump; phy_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbphy"); if (phy_off < 0) { @@ -608,6 +566,11 @@ static int mx6_parse_dt_addrs(struct udevice *dev) return -EINVAL; } + ret = fdtdec_get_alias_seq(blob, dev->uclass->uc_drv->name, + phy_off, &devnump); + if (ret < 0) + return ret; + misc_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbmisc"); if (misc_off < 0) return -EINVAL; @@ -617,6 +580,7 @@ static int mx6_parse_dt_addrs(struct udevice *dev) return -EINVAL; priv->phy_addr = addr; + priv->portnr = devnump; addr = (void __iomem *)fdtdec_get_addr(blob, misc_off, "reg"); if ((fdt_addr_t)addr == FDT_ADDR_T_NONE) @@ -664,7 +628,6 @@ static int ehci_usb_probe(struct udevice *dev) return ret; priv->ehci = ehci; - priv->portnr = dev_seq(dev); priv->init_type = type; #if CONFIG_IS_ENABLED(CLK) @@ -774,7 +737,6 @@ U_BOOT_DRIVER(usb_mx6) = { .id = UCLASS_USB, .of_match = mx6_usb_ids, .of_to_plat = ehci_usb_of_to_plat, - .bind = ehci_usb_bind, .probe = ehci_usb_probe, .remove = ehci_usb_remove, .ops = &ehci_usb_ops, |